杜邦 PBT HR5330HF 物性表
Rynite 530
ISO 11469 ISO 1043
结构件
@厚2.00毫米， 温度23.0 - 55.0°C
254 °C
英语
评论
1.56克/立方厘米
ASTM D792
0.0564磅/³
ISO 1183
30％的
0.050％ 50％RH，23℃，
@温度73.4°F
24小时 ASTM D570
0.20％ 平衡相对湿度50
@温度73.4°F ％; ISO 62，类似
微丸 微丸 PET
热稳定 材料状态 部件标识代码 聚合物产品系列 聚合物类型 加工方法 产品类别 地区 - 全球 树脂识别 符合 RoHS 标准 超声波可焊接 用途
是 当前 > PET-GF30 < 聚酯纤维 PET 注塑成型 玻璃纤维增 强树脂
是 PET-GF30 联系制造商
是 汽车上的应用 电气/电子应用
81.0 μm/m-°C
温度23.0 - 55.0°C
81.0 μm/m-°C
温度23.0 - 55.0°C
107 μm/m-°C
温度55.0 - 160°C
107 μm/m-°C
温度55.0 - 160°C
122 μm/m-°C
@厚2.00毫米， 温度23.0 - 55.0°C
122 μm/m-°C
284 °F
UL 746B
@厚度0.118
284 °F
UL 746B
@厚度0.0787
284 °F
UL 746B
@厚度0.0591
284 °F
UL 746B
@厚度0.236
HB IEC 60695-11-10
@厚度0.118
美国杜邦 PA66 HTN501NC010 物性表
HTN501 NC010 is a 30% glass reinforced, flame retardant, lubricated high performance polyamide HTN501 NC010DuPont ™ Zytel ®HTNhigh performance polyamide resinZytel ®ValueDAM50%RHIdentification Part Marking Code ISO 11469>PA6T/XT-GF35FR< Part Marking Code SAE J1344>PPA-GF35FR<Mechanical Stress at Break ISO 527MPa (kpsi)165 (24) Strain at Break ISO 527% 1.6 Tensile Modulus ISO 527MPa (kpsi)13000 (1885) Shear Strength ASTM D 732MPa (kpsi)64 (9.3)70 (10) Flexural Modulus ISO 178MPa (kpsi)12000 (1740)12000 (1740) Flexural Strength ISO 178MPa (kpsi)250 (36)235 (34)Compressive Strength ASTM D 695MPa (kpsi)293 (42.6) Compressive ModulusASTM D 695MPa (kpsi)3580 (520)Notched Charpy Impact Strength ISO 179/1eAkJ/m2-30°C (-22°F)13 23°C (73°F)11 Unnotched Charpy Impact Strength ISO 179/1eUkJ/m2-30°C (-22°F)30 23°C (73°F)40Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm. Test temperatures are 23°C unless otherwise stated.The DuPont Oval Logo, DuPont™, The miracles of science™ and Zytel® are trademarks or registered trademarks of DuPont Company. Copyright© 2008080505/080804The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated; these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in thispublication is to be considered as a license to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. CAUTION: Do not use DuPont materials in medical application involving implantation in the human body or contact with internal body fluids or tissues unless the material has been provided from DuPont undera written contract that is consistent with DuPont policy regarding medical applications and expressly acknowledges the contemplated use. For further information, please contact your DuPont representative. You may also request a copy of DuPont POLICY Regarding Medical Applications H-50103-3 and DuPont CAUTION Regarding Medical Applications … H-50102-3Zytel ®resin. It is also a PPA resin.PropertyTest Method UnitsDuring molding, use proper protective equipment and adequate ventilation. Avoid exposure to fumes and limit the hold up time and temperature of the resin in the machine. Purge degraded resin carefully with HDPE.Zytel®ValueDAM50%RHThermalDeflection Temperature ISO 75-1/-2 °C (°F)0.45MPa 270 (518) 1.80MPa260 (500)Melting Temperature ISO 11357-1/-3 °C (°F)10°C/min, First Heat 300 (574)CLTE, Parallel ISO 11359-1/-2E-4/C (E-4/F)-40 - 23°C (-40 - 73°F)0.20 (0.11) 23 - 55°C (73 - 130°F)0.18 (0.10) 55 - 125°C (131 - 257°F)0.18 (0.10)CLTE, Normal ISO 11359-1/-2E-4/C (E-4/F)-40 - 23°C (-40 - 73°F)0.46 (0.26) 23 - 55°C (73 - 130°F)0.50 (0.28) 55 - 125°C (131 - 257°F)0.60 (0.33)Glass Transition Temperature DMA °C (°F)140 (284)90 (194)Electrical Surface Resistivity IEC 60093ohm 1E13 Volume Resistivity IEC 60093ohm m >1E131E13 Electric Strength IEC 60243-1kV/mm (V/mil)1.0mm34 (863)34 (863)Relative Permittivity IEC 602501E2 Hz 3.9 1E3 Hz 3.8 1E6 Hz 3.6Dissipation Factor IEC 60250E-41E2 Hz 80 1E3 Hz 130 1E6 Hz 150Arc Resistance ASTM D 495s 80 CTIIEC 60112V 525Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm. Test temperatures are 23°C unless otherwise stated.The DuPont Oval Logo, DuPont™, The miracles of science™ and Zytel® are trademarks or registered trademarks of DuPont Company. Copyright© 2008080505/080804The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated; these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in thispublication is to be considered as a license to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. CAUTION: Do not use DuPont materials in medical application involving implantation in the human body or contact with internal body fluids or tissues unless the material has been provided from DuPont undera written contract that is consistent with DuPont policy regarding medical applications and expressly acknowledges the contemplated use. For further information, please contact your DuPont representative. You may also request a copy of DuPont POLICY Regarding Medical Applications H-50103-3 and DuPont CAUTION Regarding Medical Applications … H-50102-3PropertyTest Method UnitsHTN501 NC010Zytel®ValueDAM50%RHFlammabilityFlammability Classification UL940.81mm V-0Oxygen Index ISO 4589-1/-2%37Hot Wire Ignition UL 746As0.81mm >150 1.5mm >150 3.0mm>150Temperature Index RTI, Electrical UL 746B°C0.81mm 150 1.5mm 150 3.0mm 150RTI, Impact UL 746B°C0.81mm 120 1.5mm 125 3.0mm 130RTI, Strength UL 746B°C0.81mm 130 1.5mm 130 3.0mm150Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm. Test temperatures are 23°C unless otherwise stated.The DuPont Oval Logo, DuPont™, The miracles of science™ and Zytel® are trademarks or registered trademarks of DuPont Company. Copyright© 2008080505/080804The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated; these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in thispublication is to be considered as a license to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. CAUTION: Do not use DuPont materials in medical application involving implantation in the human body or contact with internal body fluids or tissues unless the material has been provided from DuPont undera written contract that is consistent with DuPont policy regarding medical applications and expressly acknowledges the contemplated use. For further information, please contact your DuPont representative. You may also request a copy of DuPont POLICY Regarding Medical Applications H-50103-3 and DuPont CAUTION Regarding Medical Applications … H-50102-3PropertyTest Method UnitsHTN501 NC010Zytel®ValueDAM 50%RHOther DensityISO 1183kg/m 3 (g/cm 3)1680 (1.68)Hardness, Rockwell ASTM D 785Scale M 108 Scale R 124Taber AbrasionASTM D 1044mgCS-17 Wheel, 1kg, 1000 cycles 57Water Absorption ASTM D 570%Immersion 24h 0.25Molding Shrinkage ISO 294-4%Normal, 2.0mm 0.5 Parallel, 2.0mm 0.2ProcessingMelt Temperature Range °C (°F)320-330 (610-625) Mold Temperature Range °C (°F)140-160 (280-320)Drying Time, Dehumidified Dryer h 6-8 Drying Temperature°C (°F)100 (210) Processing Moisture Content%<0.10Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm. Test temperatures are 23°C unless otherwise stated.The DuPont Oval Logo, DuPont™, The miracles of science™ and Zytel® are trademarks or registered trademarks of DuPont Company. Copyright© 2008080505/080804The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated; these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in thispublication is to be considered as a license to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. CAUTION: Do not use DuPont materials in medical application involving implantation in the human body or contact with internal body fluids or tissues unless the material has been provided from DuPont undera written contract that is consistent with DuPont policy regarding medical applications and expressly acknowledges the contemplated use. For further information, please contact your DuPont representative. You may also request a copy of DuPont POLICY Regarding Medical Applications H-50103-3 and DuPont CAUTION Regarding Medical Applications … H-50102-3PropertyTest Method Units HTN501 NC010。
聚对苯二甲酸丁二醇酯(PBT)
聚对苯二甲酸丁二醇酯（PBT）
聚对苯二甲酸丁二醇酯，英文名polybutylece terephthalate（简称PBT），PBT为乳白色半透明到不透明、结晶型热塑性聚酯。
具有高耐热性、韧性、耐疲劳性，自润滑、低摩擦系数，耐候性、吸水率低，仅为0.1%，在潮湿环境中仍保持各种物性（包括电性能），电绝缘性，但体积电阻、介电损耗大。
耐热水、碱类、酸类、油类、但易受卤化烃侵蚀，耐水解性差，低温下可迅速结晶，成型性良好。
缺点是缺口冲击强度低，成型收缩率大。
故大部分采用玻璃纤维增强或无机填充改性，其拉伸强度、弯曲强度可提高一倍以上，热变形温度也大幅提高。
可以在140℃下长期工作，玻纤增强后制品纵、横向收缩率不一致，易使制品发生翘曲。
PBT 结晶速度快，最适宜加工方法为注塑，其他方法还有挤出、吹塑、涂覆和各种二次加工成型，成型前需预干燥，水分含量要降至0.02%。
PBT（增强、改性PBT）主要用于汽车、电子电器、工业机械和聚合物合金、共混工业。
如作为汽车中的分配器、车体部件、点火器线圈骨架、绝缘盖、排气系统零部件、摩托车点火器、电子电器工业中如电视机的偏转线圈，显象管和电位器支架，伴音输出变压器骨架，适配器骨架，开关接插件、电风扇、电冰箱、洗衣机电机端盖、轴套。
另外还有运输机械零件，缝纫机和纺织机械零件、钟表外壳、镜筒、电熨斗罩、水银灯罩、烘烤炉部件、电动工具零件、屏蔽套等。
已商品化PBT合金有：PBT/弹性体、PBT/PC/弹性体、PBT/PPO、PBT/PE、PBT/ASA合金等。
0号锂基润滑脂参数
0号锂基润滑脂参数1. 简介0号锂基润滑脂是一种常见的工业润滑脂，具有优异的润滑性能和耐高温性能。
本文将介绍0号锂基润滑脂的参数，包括其化学成分、物理性质、适用范围等方面的内容。
2. 化学成分0号锂基润滑脂主要由以下几种化学成分组成：•基础油：0号锂基润滑脂通常采用合成油或矿物油作为基础油，具有良好的稳定性和润滑性能。
•锂基皂：锂基皂是0号锂基润滑脂的主要增稠剂，能够增加脂肪润滑脂的黏度和凝固点，提高其润滑性能。
•添加剂：0号锂基润滑脂还包含了各种添加剂，如抗氧化剂、防锈剂、抗磨剂等，以提高其耐高温、抗氧化和抗磨损性能。
3. 物理性质0号锂基润滑脂具有以下物理性质：•外观：0号锂基润滑脂呈黄色或棕色均匀油膏状。
•凝固点：0号锂基润滑脂的凝固点通常在60℃以上，可以在较高温度下保持润滑性能。
•滴点：0号锂基润滑脂的滴点通常在180℃以上，表示其在高温下仍能保持稳定的润滑性能。
•针入度：0号锂基润滑脂的针入度通常在265~295之间，反映了其黏度和流动性。
4. 适用范围0号锂基润滑脂适用于以下领域和设备：•工业设备：0号锂基润滑脂可以用于各种工业设备的摩擦部位，如轴承、齿轮、链条等，提供良好的润滑和保护。
•汽车工业：0号锂基润滑脂可以用于汽车发动机、变速器、制动系统等润滑部位，具有良好的抗氧化和抗磨损性能。
•航空航天：0号锂基润滑脂适用于航空航天设备的高温润滑，如发动机、起落架等，能够在极端条件下提供可靠的润滑效果。
•轨道交通：0号锂基润滑脂也适用于轨道交通设备的润滑，如铁路机车、地铁列车等，能够提供长期稳定的润滑效果。
5. 使用注意事项在使用0号锂基润滑脂时，需要注意以下事项：•清洗：在润滑部位更换润滑脂前，应先清洗干净旧润滑脂和污垢，确保新润滑脂能够有效附着和润滑。
•适量使用：使用0号锂基润滑脂时，要根据设备的要求和工作条件合理使用适量的润滑脂，避免过量或不足。
•储存条件：0号锂基润滑脂应存放在干燥、阴凉、通风的地方，避免受潮和高温，确保其质量和性能不受影响。
杜邦公司MOLYKOTE G-1068润滑脂说明书
化学品安全技术说明书科波西电子材料张家港有限公司按照GB/T 16483、GB/T 17519编制产品名称:MOLYKOTE® G-1068 润滑脂 / MOLYKOTE® G-1068 Grease SDS编号:4092334最初编制日期:27.04.2015发行日期:16.10.2020打印日期:22.06.2023科波西电子材料张家港有限公司鼓励并希望您能阅读和理解整份(M)SDS，该文件包括了重要的信息。
我们希望您能遵从该文件给出的预防措施，除非你的使用条件需要其他更合适的方法或措施。
一化学品及企业标识产品名称:MOLYKOTE® G-1068 润滑脂MOLYKOTE® G-1068 Grease推荐用途和限制用途已确认的各用途:润滑剂和润滑添加剂公司名称:科波西电子材料张家港有限公司扬子江国际化学工业园南京路3号215633 江苏省张家港市中国客户咨询方式:86-512-5561 1616*************************传真：86-21-3862 2896应急咨询电话24-小时应急联系电话:************国内应急电话:************二危险性概述紧急情况综述外观与性状糊狀物颜色白色至灰白色气味略微的长期吞咽或反复接触可能损害器官。
对水生生物有毒。
对水生生物有毒并具有长期持续影响。
GHS危险性类别根据法规的标准, 被列为有害品。
特异性靶器官系统毒性（反复接触） (经口):类别 2 (肾)急性（短期）水生危害:类别 2长期水生危害:类别 2GHS标签要素象形图信号词:警告!危险性说明长期吞咽或反复接触可能损害(肾)器官。
对水生生物有毒并具有长期持续影响。
防范说明预防措施不要吸入粉尘/ 烟/ 气体/ 烟雾/ 蒸气/ 喷雾。
避免释放到环境中。
事故响应如感觉不适，须求医/就诊。
收集溢出物。
废弃处置将内装物/容器送到批准的废物处理厂处理。
杜邦物性表-POM DELRIN100TNC010
DuPont ™ Delrin®acetal resinPRELIMINARY DATADelrin ®100T NC010IdentificationResin Identification ISO 1043POM-I Part Marking Code ISO 11469>POM-I<Mechanical Yield Stress ISO 527MPa (kpsi)52 (7.5) Yield Strain ISO 527%25 Strain at Break ISO 527%50mm/min>50Nominal Strain at Break ISO 527%>50 Tensile Modulus ISO 527MPa (kpsi)1900 (276) Flexural ModulusISO 178MPa (kpsi)1700 (245)Notched Charpy Impact Strength ISO 179/1eAkJ/m2-30°C (-22°F)13 23°C (73°F)25Unnotched Charpy Impact Strength ISO 179/1eUkJ/m 2-30°C (-22°F)NB 23°C (73°F)NBContact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm. Test temperatures are 23°C unless otherwise stated.The above data are preliminary and are subject to change as additional data are developed on subsequent lots.The DuPont Oval Logo, DuPont™, The miracles of science™ and Delrin® are trademarks or registered trademarks of DuPont Company. Copyright© 2005.060126/060126The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated; these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise. The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this publication is to be considered as alicense to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. Caution: Do not use this product in medical applications involving permanent implantation in the human body. For other medical applications see "DuPont Medical Caution Statement", H-50102.Delrin ® 100T NC010 is a toughened, high viscosity acetal homopolymer grade with high impact resistance.PropertyTest Method Units ValueDelrin ®100T NC010ThermalDeflection TemperatureISO 75f °C (°F)0.45MPa 130 (265) 1.80MPa72 (160)Melting Temperature ISO 11357-1/-3 °C (°F)10°C/min 178 (352)CLTE, Parallel ISO 11359-1/-2E-4/C (E-4/F)23 - 55°C (73 - 130°F) 1.2 (0.67)Rheological Melt Mass-Flow Rate ISO 1133g/10 min190°C, 2.16kg 2.0ElectricalRelative Permittivity IEC 602501E6 Hz 3.1Dissipation Factor IEC 60250E-41E6 Hz 90CTI IEC 60112V 600Other DensityISO 1183kg/m 3 (g/cm 3)1370 (1.37)Hardness, Rockwell ISO 2039/2Scale M 59 Scale R 113Water Absorption ISO 62, Similar to%Equilibrium 50%RH 0.3 Saturation, immersed 0.9Molding Shrinkage ISO 294-4%Normal, 2.0mm 1.9 Parallel, 2.0mm2.1Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm. Test temperatures are 23°C unless otherwise stated.The above data are preliminary and are subject to change as additional data are developed on subsequent lots.The DuPont Oval Logo, DuPont™, The miracles of science™ and Delrin® are trademarks or registered trademarks of DuPont Company. Copyright© 2005.060126/060126The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated; these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise. The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this publication is to be considered as alicense to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. Caution: Do not use this product in medical applications involving permanent implantation in the human body. For other medical applications see "DuPont Medical Caution Statement", H-50102.PropertyTest Method Units ValueDelrin ®100T NC010ProcessingMelt Temperature Range °C (°F)200-210 (390-410)Melt Temperature Optimum °C (°F)205 (400) Mold Temperature Range °C (°F)40-60 (100-140)Mold Temperature Optimum °C (°F)50 (122) Drying Time, Dehumidified Dryer h 2-4 Drying Temperature °C (°F)80 (175) Processing Moisture Content %<0.05 Hold Pressure RangeMPa (kpsi)60-80 (9-12)Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm. Test temperatures are 23°C unless otherwise stated.The above data are preliminary and are subject to change as additional data are developed on subsequent lots.The DuPont Oval Logo, DuPont™, The miracles of science™ and Delrin® are trademarks or registered trademarks of DuPont Company. Copyright© 2005.060126/060126The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated; these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise. The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this publication is to be considered as alicense to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. Caution: Do not use this product in medical applications involving permanent implantation in the human body. For other medical applications see "DuPont Medical Caution Statement", H-50102.PropertyTest Method Units Value。
PA66和PBT的简介
PA66和PBT的简介PA66-(聚酰胺66或尼龙66)聚己二酸己二胺化学式:[-NH(CH2)6－NHCO(CH2)4CO]n－外观:白包或带黄色颗粒状密度:(g/cm3)1．10-1．14 拉伸强度:(MPa) 60. 0-80．0 洛氏硬度:118 冲击强度:(kJ/m2)60-100 静弯曲强度:(MPa)100-120 马丁耐热:(℃)50-60 弯曲弹性模量:(MPa)2000～3000 体积电阻率:(Ωcm)1.83×1015 介电常数:1．63 PA66同PA6相比,PA66更广泛应用于汽车工业、仪器壳体以及其它需要有抗冲击性和高强度要求的产品.聚酰胺66-性状半透明或不透明乳白色结晶形聚合物,具有可塑性.密度1．15g/cm3.熔点252℃.脆化温度-30℃.热分解温度大于350℃.连续耐热80-120℃,平衡吸水率2．5%.能耐酸、碱、大多数无机盐水溶液、卤代烷、烃类、酯类、酮类等腐蚀,但易溶于苯酚、甲酸等极性溶剂.具有优良的耐磨性、自润滑性,机械强度较高.但吸水性较大,因而尺寸稳定性较差.聚酰胺66-应用广泛用于制造机械、汽车、化学与电气装置的零件,如齿轮、滚子、滑轮、辊轴、泵体中叶轮、风扇叶片、高压密封围、阀座、垫片、衬套、各种把手、支撑架、电线包层等.亦可制成薄膜用作包装材料.此外,还可用于制作医疗器械、体育用品、日用品等.聚酰胺66-塑模工艺燥处理:如果加工前材料是密封的，那么就没有必要干燥.然而,如果储存容器被打开,那么建议在85℃的热空气中干燥处理.如果湿度大于0.2%,还需要进行105℃,12小时的真空干燥.熔化温度:260~290℃.对玻璃添加剂的产品为275~280℃.熔化温度应避免高于300℃. 模具温度:建议80℃.模具温度将影响结晶度,而结晶度将影响产品的物理特性.对于薄壁塑件,如果使用低于40℃的模具温度,则塑件的结晶度将随着时间而变化,为了保持塑件的几何稳定性,需要进行退火处理. 注射压力:通常在750~1250bar,取决于材料和产品设计.注射速度:高速（对于增强型材料应稍低一些）. 流道和浇口:由于PA66的凝固时间很短,因此浇口的位置非常重要.浇口孔径不要小于0.5*t(这里t为塑件厚度).如果使用热流道,浇口尺寸应比使用常规流道小一些,因为热流道能够帮助阻止材料过早凝固.如果用潜入式浇口,浇口的最小直径应当是0.75mm.聚酰胺66-化学物理PA66在聚酰胺材料中有较高的熔点.它是一种半晶体-晶体材料.PA66在较高温度也能保持较强的强度和刚度.PA66在成型后仍然具有吸湿性,其程度主要取决于材料的组成、壁厚以及环境条件.在产品设计时,一定要考虑吸湿性对几何稳定性的影响.为了提高PA66的机械特性,经常加入各种各样的改性剂.玻璃就是最常见的添加剂,有时为了提高抗冲击性还加入合成橡胶,如EPDM和SBR等.PA66的粘性较低,因此流动性很好（但不如PA6）.这个性质可以用来加工很薄的元件.它的粘度对温度变化很敏感.PA66的收缩率在1%~2%之间,加入玻璃纤维添加剂可以将收缩率降低到0.2%~1%.收缩率在流程方向和与流程方向相垂直方向上的相异是较大的.PA66对许多溶剂具有抗溶性,但对酸和其它一些氯化剂的抵抗力较弱.PBT-聚对苯二甲酸丁二醇酯属于聚酯系列,是由1.4-pbt丁二醇(1.4-Butyleneglycol)与对苯二甲酸(PTA)或者对苯二甲酸酯(DMT)聚缩合而成,并经由混炼程序制成的乳白色半透明到不透明、结晶型热塑性聚酯树脂.与PET一起统称为热塑性聚酯,或饱和聚酯. PBT为乳白色半透明到不透明、结晶型热塑性聚酯.具有高耐热性、韧性、耐疲劳性,自润滑、低摩擦系数,耐候性、吸水率低,仅为0.1%,在潮湿环境中仍保持各种物性(包括电性能),电绝缘性,但体积电阻、介电损耗大.耐热水、碱类、酸类、油类、但易受卤化烃侵蚀,耐水解性差,低温下可迅速结晶,成型性良好.缺点是缺口冲击强度低,成型收缩率大.故大部分采用玻璃纤维增强或无机填充改性,其拉伸强度、弯曲强度可提高一倍以上,热变形温度也大幅提高.可以在140℃下长期工作,玻纤增强后制品纵、横向收缩率不一致,易使制品发生翘曲. PBT燃烧鉴别:不易燃烧,燃烧时无液体流下,离开火焰后在5秒钟内熄灭,相似于PC.PBT注塑参数1.注射温度:PBT的分解温度为280℃,所以实际生产中一般控制在240-260℃之间.2.注射压力:注射压力一般为50～100MPa.3.注射速率:PBT冷却速度快,因此要采用较快的注射速率.4.螺杆转速和背压:成型PBT的螺杆转速不宜超过80r/min,一般在25～60r/min之间.背压一般为注射压力的10%～15%.5.模具温度:一般控制在70～80℃,各部位的温度差不超过10℃.6.成型周期:一般情况下为15～60s.PBT注意事项1.再生料使用:再生料与新料的比例一般在25%～75%.2.脱模剂使用:一般情况下不使用脱模剂,必要时可采用有机硅脱模剂.3.停机处理:PBT停机时间在30min以内,可将温度降到200℃时停机.长期停机后再生产时,要将料筒内的料排空,再加入新料才能进行正常生产.PA66\PBT厂家东莞湘樟塑化公司，美国杜邦公司，美国杜邦公司，美国液氮公司，基础创新塑料(美国)公司，美国赫斯特公司，美国泰科纳公司，美国普立万公司，美国Chem Polymer公司，美国舒尔曼公司，美国TEKNOR APEX公司，美国RTP公司，德国朗盛公司，美国巴斯夫公司，美国巴斯夫公司，瑞士EMS，台湾耐特，广州金发。
杜邦(Dupont) Nylon 6 Zytel 73G45L
Zytel 73G45L物性表概述：Zytel 73G45L是一种45%的玻纤增强级聚酰胺，具体物性及用途如下；物理性质公英语方法密度 1.51克/立方厘米0.0546磅/³DAMISO1183 填料含量45％45％DAM吸水率 1.5％@温度23.0°C1.5％@温度73.4°F平衡50％线性成型收缩率0.0010厘米/厘米板厚1.60毫米@厚度0.0630 0.0010 / 流;DAM线性成型收缩率，流动0.0015厘米/厘米厚度2.00毫米@厚度0.0787 0.0015 / ISO294-;线性成型收缩率，横向0.0090厘米/厘米厚度2.00毫米@厚度0.0787 0.0090 / 正常;DAM力学性能公英语方法拉伸断裂强度160兆帕@温度23.0°C23200磅@温度73.4°F50％拉伸强度145兆帕温度23.0°C21000磅@温度73.4°F50％张应力0.000兆帕应变0.000％，温度-20.0°C0.000磅应变0.000％，温度-4.00°F50％RH;ISO11403-1/-2断裂伸长率 3.0％@温度23.0°C3.0％@温度73.4°FDAMASTMD638拉伸模量 4.415 GPA温度150°C640.3 KSI温度302°F50％RH;ISO527弯曲模量7.00 GPA温度23.0°C1020 KSI@温度73.4°FASTMD790，50％RH;剪切模量0.392 GPA温度210°C56.9 KSI温度410°FDAMISO6721梁缺口冲击强度，缺口 1.85焦耳/平方厘米温度23.0°C3.47 ft-lb/in温度73.4°FDAMASTMD256梁缺口冲击强度，无缺口14.9 J /厘米温度23.0°C27.9 ft-lb/in温度73.4°FDAMASTMD4812梁缺口冲击强度，缺口（ISO）15.0千焦/平方米@温度-30.0°C7.14 ft-lb/in²@温度-22.0°FDAMISO180/1A简支梁冲击缺口10.1 J /平方厘米@温度-30.0°C48.1 ft-lb/in²@温度-22.0°F50％RH;ISO179/1eU无简支梁冲击，缺口 1.90焦耳/平方厘米@温度-30.0°C9.04 ft-lb/in²@温度-22.0°FDAMISO179/1eA简拉伸蠕变模量，1小时9400兆帕温度23.0°C1.36e +6 PSI@温度73.4°F50％RH;ISO899拉伸蠕变模量，1000小时7300兆帕温度23.0°C1.06E +6 PSI@温度73.4°F50％RH;ISO899热性能公英语方法热膨胀系数，线性，并行的流500μm/m-°C温度23.0 - 55.0°C278μin/in-°F温度73.4 - 131°FDAM ASTM E 831500μm/m-°C温度23.0 - 55.0°C278μin/in-°F温度73.4 - 131°FDAM ISO 11359-1/-2热膨胀系数，线性，横向流动100μm/m-°C温度23.0 - 55.0°C55.6μin/in-°F温度73.4 - 131°FDAM ASTM E 831100μm/m-°C温度23.0 - 55.0°C55.6μin/in-°F温度73.4 - 131°FDAM ISO 11359-1/-2在0.46兆帕的热变形温度221 °C 430 °F DAM ISO 75-1/-2无冲击易燃性，UL94。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
杜邦PBT HR5330HF本色NC010黑色BK503物性表：
产品提供久隆塑胶原料tEL134********
CRASTIN®HR5330HF是30％的玻璃纤维增强，高流量（HF)，抗水解（HR）树脂。
耐冲击性及强度出色的平衡性能。
添加剂：润滑剂,、脱模助剂。
特征：可焊、耐化学试剂、水解稳定。
应用：汽车,电子电气。
熔体体积流动速度(MVR)8cm³/10min ISO1133
温度250℃ISO1133
载荷2.16kg ISO1133
模塑收缩率(平行)0.3%ISO294-4,2577
模塑收缩率(垂直) 1.0%ISO294-4,2577
拉伸模量8500MPa ISO527-1/-2
断裂应力110MPa ISO527-1/-2
断裂伸长率 2.9%ISO527-1/-2
无缺口简支梁冲击强度(+23°C)75kJ/m²ISO179/1eU
简支梁缺口冲击强度(+23°C)15kJ/m²ISO179/1eA
简支梁缺口冲击强度(-30°C)12kJ/m²ISO179/1eA
熔融温度(10°C/min)225°C ISO11357-1/-3
热变形温度(1.80MPa)205°C ISO75-1/-2
热变形温度(0.45MPa)220°C ISO75-1/-2
维卡软化温度(50°C/h50N)215°C ISO306
线性热膨胀系数(平行)21E-6/K ISO11359-1/-2
线性热膨胀系数(垂直)85E-6/K ISO11359-1/-2
1.5mm名义厚度时的燃烧性HB class IEC60695-11-10
测试用试样的厚度 1.5mm IEC60695-11-10
吸水性0.35%类似ISO62
吸湿性0.15%类似ISO62
密度1500kg/m³ISO1183。