机械工程专业英语词汇
机械专业英语词汇英文版中文版
ceramics陶瓷
synthetic fibre合成纤维
electrochemical corrosion电化学腐蚀
automotive chassis车架
suspension悬架
redirector转向器
speed changer变速器
sheet metal parts板料冲压
spot facing machining孔加工
workshop车间
engineer工程技术人员
pneuma lock气动夹紧mathematicalmodel数学模型
descriptive geometry画法几何
Mechanical drawing机械制图
projection投影
view视图
profile chart剖视图
standard component标准件
part drawing零件图
assemble drawing装配图
size marking尺寸标注
technical requirements技术要求
rigidity刚度
internal force内力
displacement位移
section截面
fatigue limit疲劳极限
fracture断裂
plastic distortion塑性变形
brittleness material脆性材料
rigidity criterion刚度准则
washer垫圈
spacer垫片
straight toothed spur gear直齿圆柱齿轮
helical-spur gear斜齿圆柱齿轮
straight bevel gear直齿锥齿轮
kinematic sketch运动简图
pinion and rack齿轮齿条
worm and worm gear蜗杆蜗轮
tempering回火
hardening and tempering调质
abrasive grain磨粒
bonding agent结合剂
grinding wheel砂轮
clearance angle后角
planing龙门刨削
spindle主轴
headstock主轴箱
chuck卡盘
machining center加工中心
lathe tool车刀
lathe车床
turning钻削
grinder磨床
benchmark基准
locksmith钳工
forge锻
stamping压模
weld焊
broaching machine拉床
broaching拉孔
assembling装配
found铸造
fluid dynamics流体动力学
fluid mechanics流体力学machining加工
hydraulic pressure液压
tangent切线
mechanotronics mechanical-
机电一体化electrical integration
air pressure pneumatic pressure气压
stability稳定性
medium介质
fluid clutch液压驱动泵hydraulic pump液压泵
valve阀门
invalidation失效
intensity强度
load载荷
stress应力
safty factor安全系数
reliability可靠性
thread螺纹
screw rod丝杠
subassembly组件
Programmable Logic Controller
可编程序逻辑控制器PLC
electric spark machining电火花加工
electric discharge wire-cutting电火花线切割加工trolley台车
carton纸箱
sub line支线
left fork叉车
Assembly line组装线
Layout布置图Conveyer流水线物料板Rivet table拉钉机
Rivet gun拉钉枪
Screw driver起子Pneumatic screw driver气动起子worktable工作桌
OOBA开箱检查
fit together组装在一起fasten锁紧(螺丝) fixture夹具(治具) pallet栈板
barcode条码
barcode scanner条码扫描器fuse together熔合
fuse machine热熔机
repair修理
operator作业员supervisor课长
cosmetic inspect外观检查
inner parts inspect内部检查thumb screw大头螺丝
EMI gasket导电条
front plate前板
rear plate后板
chassis基座
bezel panel面板
power button电源按键
reset button重置键
Hi pot test of SPS高源高压测试Voltage switch of SPS电源电压接拉链plastic parts塑胶件material check list物料检查表Tiana天那水cleaning cloth抹布
to load material上料
to unload material卸料
to return material/stock to退料
scarped报废
deficient purchase来料不良manufacture procedure制程
deficient manufacturing
制程不良procedure
scratch刮伤
defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块
feeding is not in place送料不到位stamping missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善
spare parts=buffer备件
forklift叉车
trailer=long vehicle拖板车
compund die合模
die locker锁模器pressure plate=plate pinch压板
bolt螺栓administration/general affairs
总务部
dept
automatic screwdriver电动起子thickness gauge厚薄规
gauge治具
power wire电源线
buzzle蜂鸣器defective product lable不良标签identifying sheet list标示单
location地点
present members出席人员subject主题conclusion结论
decision items决议事项responsible department负责单位
pre fixed finishing date预定完成日
approved by/checked by/prepared
核准/审核/承办by
form block折刀
stop pin定位销
round pierce punch=die button圆冲子
shape punch=die insert异形子
stock lacater block定位块
under cut=scrap chopper清角
active plate活动板
baffle plate挡板
cover plate盖板
male die公模
female die母模
groove punch压线冲子
air cushion eject rod气垫顶杆
spring box eject plate弹簧箱顶板bushing block衬套
insert入块
club car高尔夫球车capability能力
shine亮斑
splay银丝
gas mark焦痕delamination起鳞
cold slug冷块
blush导色
gouge沟槽
satin texture段面咬花witness line证示线patent专利
coolant冷却液crusher破碎机Archimedes worm阿基米德蜗杆granule=peuet=grain细粒
grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金
metal plate钣金
lathe车
mill锉
plane刨
grind磨
boring镗
blinster气泡
through hole form通孔形式voller pin formality滚针形式cam driver铡楔
shank摸柄
crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩
spline=the multiple keys花键carbonization碳化tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单
volatile挥发性
resistance电阻
combination in parallel并联式组合
parallel combined mechanism并联组合机构concurrent engineering并行工程concurred design,CD并行设计
phase angle of unbalance不平衡相位intermittent gearing不完全齿轮机构wave generator波发生器
number of waves波数
compensation补偿parameterization design,PD参数化设计
residual stress残余应力
operation control device操纵及控制装置Geneva wheel槽轮
Geneva mechanism Maltese cross槽轮机构
Geneva numerate槽数
contact ratio重合度
groove cam槽凸轮
backlash侧隙
differential gear train差动轮系differential screw mechanism差动螺旋机构transmission angle传动角transmission shaft传动轴combination in series串联式组合
series combined mechanism串联式组合机构cascade speed control串级调速innovation creation创新
creation design创新设计
normal load垂直载荷、法向载荷lip rubber seal唇形橡胶密封magnetic fluid bearing磁流体轴承
driven pulley从动带轮
driven plink,follower从动件
width of flat face从动件平底宽度follower dwell从动件停歇
follower motion从动件运动规律driven gear从动轮
bold line粗线
coarse thread粗牙螺纹
gear wheel大齿轮
packer打包机
slipping打滑
belt driving带传动
belt pulley带轮
band brake带式制动器
single row bearing单列轴承
single direction thrust bearing单向推理轴承single universal joint单万向联轴节unit vector单位矢量equivalent spur gear当量齿轮
cutter刀具
derivative导数
chamfer倒角conduction of hear导热性
lead导程
lead angle导程角
uniform motion等速运动规律conjugate breadth cam等宽凸轮equivalent link等效构件equivalent force等效力equivalent moment of force等效力矩equivalent等效量equivalent mass等效质量equivalent moment of inertia等效转动惯性dynamically equivalent model等效动力学模型chassis底座
lower pair低副
chain dotted line点划线
pitting点蚀
gasket垫圈
gasket seal垫片密封belleville spring蝶形弹簧bottom clearance顶隙
ordinay gear train定轴轮系dynamics动力学
kinematical seal动密封
dynamic energy动能
dynamic viscosity动力粘度dynamic lubrication动力润滑dynamic balance动平衡dynamic balancing machine动平衡机dynamic characteristics动态特性dynamic analysis design动态分析设计dynamic reaction动压力effective resistance工作阻力effective resistance moment工作阻力矩common normal line公法线
general constraint公共约束metric gears公制齿轮power功率
function analyses design功能分析设计
conjugate profiles共轭齿廓conjugate cam共轭凸轮link构件blower鼓风机fixed link;frame固定构件rigid coupling刚性联轴器height series高度系列height speed belt高速带heigher pair高副nominal diameter公称直径work功application factor工况系数technological design工艺设计working cycle diagram工作循环图operation mechanism工作机构external loads工作载荷working space工作空间working stress工作应力oil consumption耗油量
oil consumption factor耗油量系数H.Hertz equation赫兹公式
resultant bending moment合成弯矩
resultant froce合力resultant moment of froce合力矩black box黑箱abscissa横坐标interchangeable gears互换性齿轮feather key滑链sliding bearing滑动轴承sliding ratio滑动率slider滑块
toroid helicoids worm环面蜗杆
mechanical system机械系统balance of machinery机械平衡machine design机械设计Mechanical behavior机械特性mechanical efficiency机械效率theory of machines and
机械原理mechanisms
annular spring环形弹簧shocks缓冲装置grey cast iron灰铸铁return回程balance of rotors回转体平衡integrate积分mechanism机构
analysis of mechanism机构分析balance of mechanism机构平衡
kinematic inversion机架变换
technique process技术过程technique system技术系统machinery机械
simple harmonic motion简谐运动
key键
repeated stress交变应力repeated fluctuating load交变载荷cross belt drive交叉带传动crossed helical gears交错轴斜齿轮scoring胶合
angular acceleration角加速度angular velocity角速度
hinge铰链、枢纽correcting plane校正平面contact stress接触应力contact seal接触式密封structure结构structure design结构设计pitch point节点
circular design节距
pitch line节线
pitch circle节圆thickness on pitch circle节圆齿厚pitch diameter节圆直径block diagram框图centrifugal force离心力centrifugal stress离心应力clutch离合器centrifugal seal离心密封pitch curve理论廓线theory line of action理论啮合线membership隶属度moment力矩equilibrium力平衡couple力偶
screw nut螺母
thread pitch螺距
Screws螺钉
bolts螺栓
lead螺纹导程
wear resistance耐磨性
flexible rotor挠性转子vice台钳、虎钳
hour glass砂漏
rise升程
lift升距sleeve套筒
studs双头螺栓prime mover原动机rocker摇杆
liquid spring液体弹簧stress diagram应力图
oil can油壶preload预紧力round belt圆带
round belt drive圆带传动fillet radius圆角半径brake制动器tension张紧力tension pulley张紧轮vibration振动
right triangle直角三角形linear motion直线运动mass质量center of mass质心center distance中心距
mid plane中间平面center gear中心轮mean distance中径
final contact终止啮合点pitch周节bearing cup轴承盖bearing alloy轴承合金bearing block轴承座bearing height轴承高度bearing width轴承宽度bearing bore diameter轴承内径theory of constitution组成原理composite tooth form组合齿形stack mounting组合安装combined mechanism组合机构ordinate纵坐标applied force作用力coordinate坐标系electrolytic grinding电解研磨embossing压花加工facing面车削filing锉刀修润hand finishing手工修润hemming卷边加工
hobbing滚齿加工joggling摇动加工lapping抛光/研磨修润shaping成形加工skiving表面研磨slotting切缝切削taper turning锥度车削bearing alloy轴承合金blister steel浸碳钢
carbon tool steel碳素工具钢emery金刚砂
forging die steel锻造模用钢drill钻
drilling钻孔,钻削
bit钻嘴
drill-chuck钻头夹盘
drill-chuck-key钻头扳手layout布置图
Rivet table拉钉机
Rivet gun拉钉枪
welder电焊机
staker铆合机
glove手套
band aid创可贴
air pipe气管packaging tool打包机
wrong part错件equipment设备regulation整顿classifcation整理cleanness清扫conservation清洁
culture教养
major defect主要缺陷minor defect次要缺陷waste废料
board看板
feeder送料机
sliding rack滑料架speckle斑点
rust生锈deformation变形
burr毛边
poor staking铆合不良grease/oil stain油污
inclusion杂质
mixed color杂色
shrinking缩水to pull and stretch拉深plastic basket胶框taker取料机top stop上死点bottom stop下死点one stroke一行程location lump定位块smoothly顺利dent压痕punched hole冲孔mold成型
语词汇--电子版
英文版中文版
passive constraint虚约束
crank曲柄
racker摇杆
cams凸轮
conjugate curve共轭曲线
generation method范成法
defintional domain定义域
range值域
differential coefficient导数/微分
derivation求导
definite integral定积分
indefinite integral不定积分
curvature曲率
partial differential偏微分
rough毛坯
slide caliper游标卡尺
micrometer calipers千分尺
tap攻丝
second order determinant二阶行列式
inverse matrix逆矩阵
linear equations线性方程组
probability概率
random variable随机变量
permutation and combination排列组合
equation of state of gas气体状态方程kinetic energy动能
potential energy势能
conservation of mechanical energy机械能量守恒momentum动量
truss桁架
axes轴线
cofactor余子式
logic circuit逻辑电路
flip-flop触发器
pulse shape脉冲波形
digital analogy数模
fluid drive mechanism液压传动机构mechanical parts机械零件
quench淬火冷却
hardening淬火
helix螺旋
spline键
pin销
rolling bearing滚动轴承
sliding bearing滑动轴承spring弹簧
arrester brake制动器crosshead十字结联轴节coupling联轴器
chain链
strap皮带
finish machining精加工
rough machining粗加工gearbox casing变速箱体
rust腐蚀oxidation氧化
wear磨损durability耐用度random signal随机信号discrete signal离散信号ultrasonic sensor超声传感器integrate circuit集成电路orifice plate挡板
residual stress残余应力sleeve套筒
torsion扭力
cold machining冷加工electromotor电动机cylinder汽缸
interference fit过盈配合
hotwork热加工
CCD camera摄像头rouding chamfer倒角
optimal design优化设计industrial moulding design工业造型设计finite element有限元hobbing滚齿
gear shaping插齿actuating motor伺服电机milling machine铣床
drill machine钻床
boring machine镗床sterpper motor步进电机lead rail导轨tempering回火
phase diagram相图
heat treatment热处理
solid state phase changes固态相变nonferrous metal有色金属personnel resource department人力资源部
production department生产部门planning department企划部
QC Section品管科stamping factory冲压厂
molding factory烤漆厂
molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine冲床
robot机械手hydranulic machine油压机electrical sparkle电火花
welder电焊机
staker=reviting machine铆合机
position职务
president董事长
general manager总经理
special assistant manager特助
factory director厂长department director部长
deputy manager副理
section supervisor课长
group leader/supervisor组长
Line supervisor线长
assistant manager助理
to move,to carry,to handle搬运
be put in storage入库
pack packing包装
to apply oil擦油
to file burr锉毛刺
final inspection终检
to cinnect material接料
to reverse material翻料
wet station沾湿台
work cell工作间
work order工令
revision版次
remark备注production control confirmation生产确认checked by初审
approved by核准department部门
stock age analysis sheet库存货龄分析表on hand inventory现有库存
available material良品可使用
dents压痕
obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明part number/P/N料号
type形态
intem/group/class类别quality品质prepared by制表
notes说明
year end physical inventory difference analysis sheet 年终盘点差异分析表
physical inventory盘点数量physical count quantity账面数量difference quantity差异量cause analysis原因分析
raw materials原材料
materials物料
finished product成品
semi finished product半成品packing materials包材
good product/accepted goods良品defective product/non good parts不良品disposed goods处理品warehouse/hub仓库
on way location在途仓oversea location海外仓
spare parts physical inventory list备品盘点清单
spare molds location模具备品仓skid/pallet栈板
tox machine自铆机
wire EDM线割
EDM放电机
flow chart流程表单assenbly组装stamping冲压
molding成型coordinate坐标dismantle the die折模auxiliary fuction辅助功能poly line多义线heater band加热线thermocouple热电偶
sand blasting喷砂
grit砂砾
derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应
ram连杆
edge finder巡边器concave凸
convex凹
short射料不足nick缺口
speck瑕疵
ion离子titrator滴定仪safety factor安全系数concavity凹面wrench扳手
flat leaf spring板簧woodruff key半圆键deformation变形oscillating bar摆杆oscillating follower摆动从动件
cam with oscillating follower 摆动从动件凸轮机构
oscillating guide bar mechanism摆动导杆机构cycloidal gear摆线齿轮cycloidal tooth profile摆线齿形cycloidal motion摆线运动规律cycloidal pin wheel摆线针轮angle of contact包角
cage保持架
back to back arrangement背对背安装back angle背锥角
back cone distance背锥距
scale比例尺specific heat capacity比热容closed kinematic chain闭式链closed chain mechanism闭链机构arm臂部frequency cinverters变频器frequency control of motor speed变频调速speed change变速
change gear change wheel变速齿轮modified gear变位齿轮modification coefficient变位系数standard spur gear标准齿轮
superficial mass factor标准直齿轮surface roughness表面质量系数parallelmechanism并联机构hob,hobbing cutter齿轮滚刀gear齿轮机构blank齿轮轮坯pinion unit齿轮传动系gear coupling齿轮联轴器rack gear齿条传动tooth number齿数
gear ratio齿数比
rack齿条
rack cutter;rack shaped shaper
齿条插刀cutter
silent chain齿形链
form factor齿形系数tooth ratchet mechanism齿式棘轮机构gear shaper插齿机coincident points重合度punch冲床transmission ratio,speed ratio传动比gearing;transmission gear传动装置driven system传动系统bearing capacity承载能力paired mounting成对安装dimension series尺寸系列tooth space齿槽spacewidth齿槽宽backlash齿侧间隙addendum齿顶高addendum circle齿顶圆dedendum齿根高dedendum circle齿根圆
tooth thickness齿厚
circular pitch齿距
face width齿宽
tooth profile齿廓
tooth curve齿廓曲线speed changing gear boxes齿轮变速箱pinion and rack齿轮齿条机构dynamic load动载荷transverse plane端面transverse parameters端面参数transverse circular pitch端面齿距transverse tooth profile端面轮廓transverse contact ratio端面重合度transverse module端面模数