M12工业以太网交换机,EN50155嵌入式轨道交通插座
EN50155标准工业以太网交换机
产品特性支持8个10/100M以太网M12接口，2个1000M光口或2个10/100/1000M电口（M12）符合轨道交通EN50155标准,M12航空插头接口设计支持MR-Ring快速环网（自愈时间<20ms），兼容STP/RSTP/MSTP生成树协议支持QoS，基于端口的流量监管，WRR、DRR、SP、队列调度算法、报文的802.1p支持bypass功能可选满足工业4级电磁兼容性，IP54等级，无风扇设计产品概述MIES-5710系列产品是一款二层千兆工业以太网交换机，配置了8个10/100M以太网接口，2个1000M光口或2个10/100/1000M M12电口。
该交换机提供丰富的功能：支持MR-ring 环网协议，兼容STP/RSTP/MSTP、基于端口的VLAN、基于802.1Q的VLAN、QOS、IGMP Snooping、广播风暴抑制、端口聚合、端口镜像、端口状态管理等。
可选支持bypass功能。
设备符合IEEE802.3，IEEE802.3u标准，IEEE802.3ab和IEEE802.3x规范。
MIES-5710支持Console、Telnet、Web多种管理方式。
该系列具备IP54防护等级，适合在各种干扰较大的场合使用，如交通行业中震动和冲击非常频繁，使用M12则可以使得连接更为牢固。
此外MIES-5710系列安装方式提供壁挂式安装，可为现场安装节省空间。
产品参数属性MIES-5710接口8个1O/1OOM自适应以太网电口，M12接口2个1000M光口或2个10/100/1000M M12电口以太网口速率和距离1O/1OO/1000M自适应双绞线,最大传输距离100m光口属性及传输距离单模1310nm，多模850nm；单模20km,多模550m（长距离模块可定制）背板带宽 5.6Gbps包转发速率 4.6Mpps包缓存区2MbitMAC表支持8K个MAC地址VLAN支持基于端口的VLAN（4096个），802.1QVLAN支持GVRP二层环网协议支持MR-ring（自愈时间<20ms）支持STP/RSTP/MSTP自愈环组网方式支持多组自愈环支持相切环端口聚合支持静态聚合支持LACP动态聚合DHCP DHCP Client DHCP Relay DHCP Server端口镜像支持流镜像支持本地镜像组播支持IGMP Snooping v1/v2/v3，MLD Snooping v1支持IGMP v3QoS 支持对端口接收报文的速率和发送报文的速率进行限制支持CAR（Committed Access Rate）功能支持每个端口支持8个输出队列支持灵活的队列调度算法，可以同时基于端口和队列进行设置支持SP、WRR、SP+WRR三种模式ACL 支持L2（Layer2）~L4（Layer4）包过滤功能，提供基于源MAC地址、目的MAC地址、源IP(IPv4)地址、目的IP(IPv4)地址、TCP/UDP 端口号的流分类NTP<10ms网络安全支持用户分级管理和口令保护支持802.1X认证支持RADIUS认证支持端口隔离支持动态ARP检测支持IP/Port/MAC的绑定功能管理与维护支持FTP/TFTP加载升级支持命令行接口（CLI）配置支持Telnet远程配置支持通过Console口配置支持SNMP v1/v2/v3支持系统日志，分级告警，调试信息输出支持Ping风暴抑制可分别对广播、组播、未知单播速率控制指示灯电源指示，接口灯指示电源输入电压：AC/DC85～265V支持过载保护，反接保护，冗余保护最大功耗：10W工作环境工作温度：-40℃～+75℃储存温度：-40℃～85℃相对湿度：5％～95％无凝露安装方式DIN 桌面式/壁挂式安装外形尺寸宽×高×深：180×73×248mm 防护等级IP 54防护等级，无风扇设计MTBF350,000小时质保期5年符合标准IEEE802.3：CSMA/CDIEEE802.3i：10Base-TIEEE802.3u：100Base-TIEEE802.3z:1000Base-LXIEEE 802.3ad：链路聚合IEEE 802.3x：全双工以太网数据链路层流控IEEE 802.1p：流量优先级IEEE 802.1Q：VLANIEEE 802.1w：快速生成树IEEE 802.1X：基于端口的网络访问控制铁路电气标准EN50155EMI 电磁干扰度测试EMCIEC61000-4-2(ESD)±8kV(contact),±15kV(air)IEC61000-4-3(RS)10V/m(80MHz～2GHz)IEC61000-4-4(EFT)Power Port:±4kV;Data Port:±2kVIEC61000-4-5(Surge)Power Port:±2kV/DM,±4kV/CM;Data Port:±2kVIEC61000-4-6(CS)3V(10kHz～150kHz);10V(150kHz～80MHz)IEC61000-4-16(共模传导)30V(cont.),300V(1s)安装图示订货信息产品型号规格参数MIES-5710M8个10/100M 以太网口，2个1000M 多模光口或2个10/100/1000M 电口（M12连接器），输入电压：AC/DC85～265V MIES-5710S 8个10/100M 以太网口，2个1000M 单模光口或2个10/100/1000M 电口（M12连接器），输入电压：AC/DC85～265V上海兆越通讯技术有限公司创立于 2003 年，是国家科技部创新基金立项企业；公司致力于工业通信的产品研发与技术创新，专注于工业以太网通信、工业无线通信、现场总线、光纤通信、嵌入式通信，目前已成功推出数十条产品线、几百种产品，已成为国内工业通信领域的品牌。
moxa交换机
经过严格的ESD、EFT、宽温测试、抖动测 试、振动测试等严格的硬件测试
MOXA工业交换机的硬件特性
恶劣的工业现场环境
MOXA的工业交换机
环境温差大
低功耗无风扇 宽温设计
环境湿度大
工作湿度5-95%RH,无 凝露
5：EDS-P308系列：8口IEEE 802.3af PoE非网管型工业以太网交换机 6：EDS-P206A-4POE系列：6口IEEE 802.3af/at PoE+非网管型以太网交换
机 7：EDS-P510系列：7+3G口千兆IEEE 802.3af POE网管型以太网交换机 8：EDS-P506A-4POE系列：6口IEEE 802.3af/at PoE+网管型以太网交换机 9：SPL-24系列：适用于EDS-P510，EDS-P308和IKS-6726-8PoE系列PoE
操作温度范围，无风扇操 作，坚固耐用的外形设计， 以及一系列工业标准认证， 为严苛的工业应用保证高 网络可用性和环境适应能 力。
ICS-G7848/G7850/G7852系列 IKS-G6826/6828系列
MOXA IKS系列工业机架式以太网交换机
ICS-G7848/G7850/G7852系列：48G/48G+2 10GbE/48G+4 10GbE口全千兆网管型三层核心以太网交换机
工业以太网交换机
将以太网络应用于工业环境 与现场工业总线无缝兼容 无需更改现场总线的数据格式和协议 满足苛刻的工业现场环境 符合工业应用的安规标准 满足工业现场的安装方式 设备具有高可靠性 网络具有备份冗余功能和突发事件报警机制
NEBU-M12系列插座与插头连接器操作手册说明书
原版操作手册的译本© 2020 Festo SE & Co. KG 保留一切权利1适用文件有关产品的所有可用文件 è 。
2安全2.1安全注意事项–仅在无电压情况下进行插拔连接。
–仅允许将产品安装在处于安全状态的部件上。
2.2按规定使用连接电缆用于连接现场用设备（传感器、执行元件）和控制器。
3结构3.1产品配置1插座 M12x12插头 M12x13电缆Fig. 1 NEBU-M12G5-...-M12G...1插座 M12x12插头 M12x13电缆Fig. 2 NEBU-M12G5-...-M12W...1插座 M12x12插头 M12x13电缆4开关状态显示（可选）Fig. 3 NEBU-M12W5...-M12G...1插座 M12x12插头 M12x13电缆4开关状态显示（可选）Fig. 4 NEBU-M12W5...-M12W...1插座 M12x12插头 M12x13电缆Fig. 5 NEBU-M12G5-E-...-Q8N-M12G53.2针脚分配1) 颜色代码符合 IEC 60757:1983-01Tab. 1 针脚分配4装配4.1安装现场设备端1.将插座 1 与适配的插头对齐。
2.将插座 1 插到插头上。
3.拧紧插座 1 的螺丝紧固。
拧紧扭矩：0.3 Nm ± 67 %4.2安装控制端1.将插头 2 与适配的插座对齐。
2.将插头 2 插入插座中。
3.拧紧插头 2 的螺丝紧固。
拧紧扭矩：0.3 Nm ± 67 %4.3电缆敷设属性电缆属性电缆敷设-K-标准拖链中（弯曲半径 75 mm）或柔性（可自由移动，无导向的敷设）电缆可灵活弯曲，但不可用于机器人。
-E-适合于导向链中继用于拖链中或柔性敷设-R-适合于机械手用在机器人上、用于拖链中或柔性敷设Tab. 2 电缆敷设4.4拖链中的安装1.根据实际铺设情况截取所需长度的拖链。
2.拖链中的电缆铺设无扭曲。
Kyland-Aquam8012A-二层千兆网管型EN50155系列工业以太网交换机
Aquam8012A12/9+3G/8+4G端口二层千兆网管型EN50155系列工业以太网交换机产品简介Aquam8012A系列是专为轨道交通行业设计的二层网管型工业以太网交换机，最大支持8个百兆快速以太网接口及4个千兆上行接口，支持壁挂式安装方式，支持宽范围的可操作温度（-40℃~+70℃），满足EN50155、EN50121等轨道交通行业标准的要求。
Aquam8012A具有更优化的外形尺寸，便于灵活安装；支持IP65高防护等级，满足设备对防尘防水性能的要求；支持M12接口形式，保证端口连接的密封性和牢固性，尤其适合有强烈的振动和冲击的应用场景。
Aquam8012A系列交换机提供支持PoE功能的型号，支持宽范围的隔离电源（电源输入范围可达24VDC~110VDC），可提供9个支持IEEE802.3at PoE+（兼容IEEE802.3af）的百兆快速以太网接口，能够驱动9个支持IEEE802.3at/af的受电设备PD，减少终端设备的线缆连接。
交换机作为PSE设备可为每个端口提供最大30.8W的功率，整机可提供最大61.6W+的PoE功率输出。
Aquam8012A系列以太网交换机支持用于IP地址自动分配的DHCP协议，并且支持DRP和RSTP环网冗余协议，可以灵活组网，以满足铁路市场的需求。
Aquam8012A可广泛用于车载PIS、CCTV、视频监控系统、列车控制系统，同时也适用于任何对振动冲击、EMC兼容性要求严酷的工业应用场合。
关键特性该系列最多支持3个千兆电口+9个百兆电口或者4个千兆口+8个百兆口或12个百兆口支持最多达9个PoE接口支持Bypass功能可选该系列支持带PoE型号和不带PoE型号可选POE支持IEEE802.3af和IEEE802.3at标准电源接口及端口连接器型号支持M12支持DRP和RSTP环网冗余保护符合EN50155和EN50121行业标准要求,专为轨道交通应用设计防护等级IP65，需IP67请联系我司性能参数机械尺寸订购信息推荐型号带散热肋型号产品型号Aquam8012A-Ports-PS1-PS2代码定义代码选型Ports:端口3GE9T=3X10/100/1000BASE-TX M12电口; 9X10/100BASE-TX M12电口;4GE8T=4X10/100/1000BASE-TX M12电口; 8X10/100BASE-TX M12电口;3GE9P=3X10/100/1000BASE-TX M12电口; 9X10/100BASE-TX M12 PoE电口;4GE8P=4X10/100/1000BASE-TX M12电口; 8X10/100BASE-TX M12 PoE电口;9T=9X10/100BASE-TX M12电口;9P=9X10/100BASE-TX M12 PoE电口;产品型号Aquam8012A-B-Ports-PS1-PS2B:4GE型号千兆口支持2对Bypass功能;3GE型号千兆口支持1对Bypass功能;Ports:端口3GE9T=3X10/100/1000BASE-T(X) M12电口; 9X10/100BASE-T(X) M12电口;4GE8T=4X10/100/1000BASE-T(X) M12电口; 8X10/100BASE-T(X) M12电口;3GE9P=3X10/100/1000BASE-T(X) M12电口; 9X10/100BASE-T(X) M12 PoE电口;4GE8P=4X10/100/1000BASE-T(X) M12电口; 8X10/100BASE-T(X) M12 PoE电口;PS1-PS2:电源输入非PoE型号：H6-H6=72-110VDC(50.4-137.5VDC),冗余输入L14-L14=48VDC(33.6-60VDC),冗余输入L13-L13=24VDC(16.8-30VDC),冗余输入PoE型号：WV-WV=24-110VDC(16.8-154VDC),冗余输入去散热肋型号产品型号Aquam8012A-Ports-PS1-PS2-LVPorts:端口3GE9T=3X10/100/1000BASE-T(X) M12电口; 9X10/100BASE-T(X) M12电口;4GE8T=4X10/100/1000BASE-T(X) M12电口; 8X10/100BASE-T(X) M12电口;9T=9X10/100BASE-T(X) M12电口;产品型号Aquam8012A-B-Ports-PS1-PS2-LVB:4GE型号千兆口支持2对Bypass功能;3GE型号千兆口支持1对Bypass功能;Ports:端口3GE9T=3X10/100/1000BASE-T(X) M12电口;9X10/100BASE-T(X) M12电口;4GE8T=4X10/100/1000BASE-T(X) M12电口;8X10/100BASE-T(X) M12电口;PS1-PS2:电源输入H6-H6=72-110VDC(50.4-137.5VDC),冗余输入L14-L14=48VDC(33.6-60VDC),冗余输入L13-L13=24VDC(16.8-30VDC),冗余输入选购配件配件型号描述备注M12-A-4P-F M12, A-Coding, 4 Pin母头电缆连接器电源连接器头M12-A-4P-M M12, A-Coding, 4 Pin公头电缆连接器Console/USB口连接器头M12-D-4P-M M12, D-Coding, 4 Pin公头电缆连接器百兆电口连接器头M12-X-8P-M M12, X-Coding, 8 Pin公头电缆连接器千兆电口连接器头DT-XL-PWR-M12-XXX-3m电源接口连接线M12 to裸端，3m电源接头线缆Version:2020-07-22 17:26:18。
Moxa轨道交通网络解决方案
赫斯曼交换机产品介绍
• 9 ports • 17 ports • 25 ports
3FX / 6TX 3FX / 14TX 3FX / 22TX
e.g.：RS20-0900MMM2SDAE
7
4个光纤接口的千兆交换机
2 个千兆光口 2 个百兆光口 6/14/22 ports
1000BaseFX SFP插槽方式(LC型连接器） 100BaseFX SFP插槽方式(LC型连接器) 10/100 TX
13
产品型号－ OPENRAIL系列
1设计 2端口数量 3端口类型 4工作温度及涂层 5供电要求 6认证要求 7软件功能版本 8配置类型 9OEM类型 10软件发布号
RS30 08 00 M2 S2 S D A E H C 02.0
14
RS30 － 08 02 T1 O6 S D A P H C 01.0
赫斯曼工业以太网交换机产品说明
上海海得控制系统股份有限公司 工业IT事业部 交通行业组 王海刚
1
赫斯曼交换机的特性
外形 设计区分 端口数量 端口带宽类型 端口介质类型 端口连接器 温度范围 保护土层(PCB) 供电类型 认证要求
软件版本
增加客户定制的特性
外形尺寸大小？ 机架式(MACH,LION系列)/一体化(RS系列)/模块化(MS系列) 能提供或支持的最大端口数量 10GE,GE 或 FE 双绞线，多模光纤，单模光纤及长距离光纤等 RJ45，M12，MTRJ，SC，LC，ST 标准 0℃ -> +60℃，或扩展 -40℃ -> +70℃ 标准，或带保护涂层（防止SO2，H2S...） 12/24/48VDC，24 VAC …… 标准 cUL 508 cUL1604 class 1 DIV2 扩展增加 German LIoyd，铁路标准 EN 50121-4 和 EN 50155，ATEX 100a Zone 2，Substation IEC 61850 标准版（提供普遍的诊断、交换和相关冗余功能） 增强版（除具备增强版的所有功能以外，还带有更多安全和 冗余功能） 例如软件配置，OEM 版本，软件版本等
毛斯 Moxa ToughNet TN-5816A 5818A 高性能 M12 层3 以太网交换机说
P/N: 1802058000011 *1802058000011*TN-5816A/5818A Quick Installation GuideMoxa ToughNet SwitchEdition 2.0, February 2017Technical Support Contact Information/supportMoxa Americas:Toll-free: 1-888-669-2872 Tel: 1-714-528-6777 Fax: 1-714-528-6778 Moxa China (Shanghai office): Toll-free: 800-820-5036 Tel: +86-21-5258-9955 Fax: +86-21-5258-5505 Moxa Europe:Tel: +49-89-3 70 03 99-0 Fax: +49-89-3 70 03 99-99 Moxa Asia-Pacific:Tel: +886-2-8919-1230 Fax: +886-2-8919-1231 Moxa India:Tel: +91-80-4172-9088 Fax: +91-80-4132-10452017 Moxa Inc. All rights reserved.OverviewThe ToughNet TN-5816A/5818A switches are high performance M12 Layer 3 Ethernet switches that support Layer 3 routing functionality to facilitate the deployment of applications across networks.TN-5816A/5818A switches use M12 and other circular connectors to ensure tight, robust connections and guarantee reliable operation against environmental disturbances, such as vibration and shock.TN-5816A/5818A switches support isolated power in the 24 to 110 VDC power input range, allowing the same model to be used at different sites around the globe. TN-5816A/5818A switches provide up to 16 Fast Ethernet M12 ports with 2 bypass relay ports, and 2 Ethernet interface Gigabit ports with bypass relay functionality. Furthermore, with a -40 to 75°C operating temperature and IP54-rated waterproof enclosure, the switches can be deployed in harsh environments. The TN-5816A/5818A series Ethernet switches are compliant with mandatory sections of EN 50155, covering operating temperature, power input voltage, surge, ESD, and vibration, as well as conformal coating and power insulation, making the switches suitable for a variety of industrial applications. Package ChecklistYour ToughNet TN-5816A/5818A switch is shipped with the following items. If any of these items is missing or damaged, please contact your customer service representative for assistance.• 1 Moxa ToughNet switch•M12 to DB9 console port cable• 2 protective caps for console and relay output ports•Panel mounting kit•CD-ROM with user’s manual, Windows utility, and SNMP MIB file •Quick installation guide (printed)•Warranty cardFeaturesAnti-Vibration Circular Connectors for Robust Links•M12 D-coding 4-pin female connectors for Fast Ethernet 10/100BaseT(X) ports.•M12 X-coded 8-pin connector for Gigabit Ethernet10/100/1000BaseT(X) ports•M12 A-coding 5-pin male connectors for console and relay output. •M23 6-pin male connector for power input.Dual Isolated Power Inputs•24 to 110 VDC (16.8 to 137.5 VDC), isolated.Designed for Industry-specific Applications•Two Gigabit Ethernet ports to meet high bandwidth requirements. •Bypass relay ensures non-stop data communication in the event the switch stops working due to a power failure.•Complies with all EN 50155 mandatory test items*.•-40 to 75°C operating temperature range.•IP54, rugged high-strength case.•Panel mounting or DIN-rail mounting installation capability.*This product is suitable for rolling stock railway applications, as defined by the EN 50155 standard. For a more detailed statement, click here: /doc/specs/EN_50155_Compliance.pdfRecommended Optional Accessories•CBL-M23(FF6P)Open-BK-100-IP67: 1-meter M23 to 6-pin power cable with IP67-rated female 6-pin M23 connector•CBL-M12D(MM4P)/RJ45-100 IP67: 1-meter M12-to-RJ45 Cat-5E UTP Ethernet cable with IP67-rated male 4-pin M12 D-coded connector •CBL-M12(FF5P)/OPEN-100 IP67: 1-meter M12-to-5-pin power cable with IP67-rated female 5-pin M12 A-coded connector•M12D-4P-IP68: Field-installable M12 D-coded screw-in connector, male 4-pin, IP68-rated•M12A-5P-IP68: Field-installable M12 A-coded screw-in connector, female 5-pin, IP68-rated•CAP-M12F-M: Metal cap for M12 female connector•DK-DC50131: DIN-rail mounting kit, 50 x 131 mm1.Model name2.Screw holes for panel mounting kit3.Console port4.Grounding screw5.Relay output port6.Power input voltage range indicator7.Power input port (male 6-pin shielded M23 connector)8.PWR1 LED: for power input 19.PWR2 LED: for power input 210.FAULT LED11.MSTR/HEAD LED: for ring master or chain head12.CPLR/TAIL LED: for ring coupler or chain tail13.TP port’s 10/100 Mbps LED14.10/100BaseT(X) port (female 4-pin shielded M12 connector with Dcoding)15.Waterproof vent16.Product label17.12 screw holes for DIN-rail mounting kit18.E2 LED: Not used by the TN-5816 series19.E1 LED: Not used by the TN-5816 series20.Ports 9-10, 13-14 with relay bypass function1.Model name2.Screw holes for panel mounting kit3.Console port4.Grounding screw5.Relay output port6.Power input voltage range indicator7.Power input port (male 5-pin shielded M23 connector)8.PWR1 LED: for power input 19.PWR2 LED: for power input 210.FAULT LED11.MSTR/HEAD LED: for ring master or chain head12.CPLR/TAIL LED: for ring coupler or chain tail13.TP port’s 10/100 Mbps LED14.10/100BaseT(X) port (female 4-pin shielded M12 connector with Dcoding)15.Waterproof vent16.Product label17.12 screw holes for DIN-rail mounting kit18.E2 LED: Down-side E2 Gigabit port’s 10/100/1000 Mbps LED19.E1 LED: Down-side E1 Gigabit port’s 10/100/1000 Mbps LED20.Gigabit Ethernet port E1 (corresponding to port 17 in the TN-5818AUser's Manual; ports 17-18 support relay bypass function)21.Gigabit Ethernet port E2 (corresponding to port 18 in the TN-5818AUser’s Manual; ports 17-18 support relay bypass function)22.Ports 9-10, 13-14 with relay bypass functionMounting Dimensions (unit = mm)TN-5816A SeriesTN-5818A SeriesPanel/Wall MountingSTEP 1:Mounting the TN-5816A/5818A to a wall requires 4 screws. Use the ToughNet switch as a guide to mark the correct positions of the 4 screws. STEP 2:Use the 4 screws in the panel mounting kit. If youwould like to use your own screws, make sure thescrew head is between 6.0 mm and 7.0 mm indiameter and the shaft is less than 4.0 mm indiameter, as shown at the right.Do not screw the screws in all the way—leave a space of about 2 mm to allow room for sliding the ToughNet switch between the wall and the screws.NOTE Before tightening the screws into the wall, make sure the screw head and shaft size are suitable by inserting the screw through one of the keyhole-shaped apertures of the ToughNet switch.STEP 3:Once the screws are fixed in the wall, hang the ToughNet switch on the 4 screws through the large opening of the keyhole-shaped apertures, and then slide the switch downwards. Tighten the four screws for added stability.NOTE To provide greater protection from vibrations and shocks, use screws with shaft diameter between 6.0 mm and 7.0 mm, and fix the ToughNet switch onto the wall directly through the large opening of the keyhole-shaped apertures.DIN-Rail Mounting (optional)Use the optional DIN-rail mounting kit (DK-DC50131, must bepurchased separately) to mount the TN-5816A/5818A on a 35 mm DIN-rail.STEP 1: Use 12 screws (6 screws per plate) to attach the two DIN-rail attachment plates to the rear panelof the switch.STEP 2: If the spring-loaded bracket is locked in place, push the recessed button to release it. Once released, you should feel some resistance from the spring as you slide the bracket up and down a few millimeters in each direction.STEP 3: Position the ToughNet switch on the DIN-rail, tilted so the clamps hook over the top edge of the rail.STEP 4: Swing the switch down fully onto the DIN-rail, until both clamps completely latch.To remove the Moxa ToughNet Switch from Array the DIN-rail, use a screwdriver to pull out thetwo spring-loaded brackets from the bottomuntil they are fixed in a “locked” position.Then, reverse Steps 3 and 4 above.Wiring RequirementsPlease Read and Follow These Guidelines:•Use separate paths to route wiring for power and devices. If power wiring and device wiring paths must cross, make sure the wires are perpendicular at the intersection point.NOTE: Do not run signal or communications wiring and power wiring through the same wire conduit. To avoid interference, wires withdifferent signal characteristics should be routed separately.•You can use the type of signal transmitted through a wire to determine which wires should be kept separate. The rule of thumb is that wiring that shares similar electrical characteristics can bebundled together.•Keep input wiring and output wiring separated.•It is strongly advised that you label wiring for all devices in the system when necessary.Grounding the ToughNet SwitchGrounding and wire routing help limit the effects of noise due to electromagnetic interference (EMI). Run the ground connection from the grounding screw to the grounding surface prior to connecting devices.Connecting the Power SuppliesThe ToughNet TN-5816A/5818A series switches support two sets of power supplies—power input 1 and power input 2. The M23 6-pin male connector on the TN-5816A/5818A’s front panel is used for the dual power inputs.Pinouts for the power input port on the TN-5816A/5818ASTEP 1: Plug the power cord connector into the TN-5816A/5818A’s power input port.STEP 2: Screw in the nut on the power cord connector to the power input connector (on the switch) to ensure a tight connection.Connecting the Relay OutputsEach TN-5816A/5818A switch has two sets of relay outputs—relay output 1 and relay output 2.The M12 A-coded 5-pin male connector on the TN-5816A/5818A front panel is used for the two relay outputs. Use a power cord with an M12 A-coded 5-pin female connector to connect the relay contacts. You can purchase an M12 power cable from Moxa; the model number is CBL-M12 (FF5P)/OPEN-100 IP67.Pinouts for the TN-5816A/5818A’s relay output portN.C.: Not connectedFAULT:The two sets of relay contacts of the M12 A-coded 5-pin male connector are used to detect user-configured events. The two wires attached to the fault contacts form an open circuit when a user-configured event is triggered. If a user-configured event does not occur, the fault circuit remains closed.Connecting the Data Lines10/100BaseT(X) Ethernet Port ConnectionAll TN-5816A/5818A models have 16 10/100BaseT(X) Ethernet ports (4-pin shielded M12 connector with D coding). The 10/100TX ports located on the TN-5816A/5818A front panel are used to connect to Ethernet-enabled devices. Most users configure these ports for Auto MDI/MDI-X mode, in which case the port’s pinouts are adjusted automatically depending on the type of Ethernet cable used (straight-through or cross-over), and the type of device (NIC-type or HUB/Switch-type) connected to the port.In what follows, we give pinouts for both MDI (NIC-type) ports and MDI-X (HUB/Switch-type) ports. We also give cable wiring diagrams for straight-through and cross-over Ethernet cables.10/100BaseT(X) Port PinoutsHousing: shield10/100/1000BaseT(X) M12 (8-pin) Port PinoutsM12 (4-pin, M) to M12 (4-pin, M) Cross-Over Cable WiringM12 (4-pin, M) to M12 (4-pin, M) Straight-Through Cable WiringM12 (4-pin, M) to RJ45 (8-pin) Cross-Over Cable WiringM12 (4-pin, M) to RJ45 (8-pin) Straight-Through Cable WiringBypass Relay FunctionThe TN-5816A/5818A is equipped with a bypass relay function. When the switch is operating normally, these bypass ports work in the same way as the other ports. That is, frame ingressions are processed and thenforwarded. If the switch stops working due to a power failure, the bypass relay function will be triggered to ensure non-stop data communication. The figure below illustrates the bypass relay function. For example, if Switch B loses power, then the two Gigabit ports will be bypassed through the relay circuit and the transmission line from Switch A to B and the transmission line from Switch B to C will interconnect automatically, ensuring that power continues to be supplied.The bypass relay function helps the network recover from single-node failures in a linear topology.Since the maximum segment length of category 5 twisted-pair cable is 100 meters, cable length must be considered when designing a network that utilizes this function. For example, the total length of the cables from Switch A to B and from B to C must be no more than 100 meters. This way, if the two adjacent nodes (switch B and C for example) encounter a power failure, there will be no stoppage, provided that the total length of the cables A-to-B, B-to-C, and C-to-D are no more than 100 meters.The bypass relay function works best for networks with linear topologies. ToughNet™ switches with bypass relay function are not recommended to be used in networks that employ ring topologies because network loops may occur when redundancy protocols such as RSTP or TurboRing™ are applied.Bypassing Switch A Switch B Switch C Switch DLED IndicatorsSeveral LED indicators are located on the ToughNet switch’s front panel. The function of each LED is described in the table below.Specifications。
摩克（Moxa）TN-5305系列EN501555-口IP67无管理Ethernet开关产品介绍说明
TN-5305SeriesEN501555-port IP67unmanaged Ethernet switchesFeatures and Benefits•10/100BaseT(X),4-pin M12(D-coded),F/H duplex mode,and auto MDI/MDI-X connection•IP67-rated housing protection•Power input:12to45VDC,18to30VAC•Complies with all EN50155mandatory test items1•-40to75°C operating temperature range(-T models)CertificationsIntroductionThe TN-5305Series Ethernet switches are IP67-rated for tough industrial applications.By using M12connectors,you can rest assured that Ethernet cables will connect tightly to the switch,and will be robust enough to protect your applications from external disturbances,such as the vibration and shock encountered in the transportation industry.The space-saving TN-5305switches can be mounted virtually anywhere,and wide operating temperature(-40to75°C)models are also available for use in the most extreme weather conditions.TN-5305Series Ethernet switches comply with a portion of EN50155specifications,covering operating temperature,power input voltage,surge,ESD,and vibration,making the switches suitable for a variety of industrial applications.SpecificationsEthernet Interface510/100BaseT(X)Ports(M12D-coded4-pin femaleconnector)Standards IEEE802.3for10BaseTIEEE802.3u for100BaseT(X)IEEE802.3x for flow controlPower ParametersInput Current0.1A@24VDC,0.08A@36VDCInput Voltage18to30VAC(47to63Hz)24to36VDCNo.of Power Inputs1Operating Voltage18to30VAC12to45VDCPower Connector M12A-coded male connectorPhysical CharacteristicsHousing Plastic top cover,metal bottom plateIP Rating IP671.This product is suitable for rolling stock railway applications,as defined by the EN50155standard.For a more detailed statement,click here:/doc/specs/EN_50155_Compliance.pdfDimensions60x125x29.6mm(2.36x4.92x1.09in) Weight Packaged:270g(0.56lb)Installation DIN-rail mounting(with optional kit)Wall mountingEnvironmental LimitsOperating Temperature TN-5305:-25to60°C(-13to140°F)TN-5305-T:-40to75°C(-40to167°F)Storage Temperature(package included)-40to85°C(-40to185°F)Ambient Relative Humidity5to95%(non-condensing)Altitude2000mStandards and CertificationsFreefall IEC60068-2-32EMC EN55032/35EMI CISPR32,FCC Part15B Class AEMS IEC61000-4-2ESD:Contact:6kV;Air:8kVIEC61000-4-3RS:80MHz to1GHz:20V/mIEC61000-4-4EFT:Power:2kV;Signal:2kVIEC61000-4-5Surge:Power:2kV;Signal:2kVIEC61000-4-6CS:10VIEC61000-4-8PFMFEnvironmental Testing IEC60068-2-1,EN50155IEC60068-2-14,EN50155IEC60068-2-2,EN50155IEC60068-2-30,EN50155International Approval RCMRailway EN50121-4EN50155Railway Fire Protection EN45545-2Safety EN60950-1UL508Salt Spray Test IEC60068-2-11,EN50155Shock IEC60068-2-27,IEC61373,EN50155 Vibration IEC60068-2-64,IEC61373,EN50155 DeclarationGreen Product RoHS,CRoHS,WEEEMTBFTime3,451,678hrsStandards Telcordia SR332WarrantyWarranty Period5yearsDetails See /warrantyPackage ContentsDevice1x TN-5305Series switch Installation Kit1x panel-mounting kit Documentation1x quick installation guide1x warranty card DimensionsOrdering InformationModel Name PoE,10/100BaseT(X)Ports,M12D-CodedFemale Connector10/100BaseT(X)Ports,M12D-Coded FemaleConnectorPower Input Input Voltage Operating Temp.TN-5305–5Single input 24/36VDC,18to30VAC-25to60°CTN-5305-T–5Single input 24/36VDC,18to30VAC-40to75°CAccessories(sold separately)CablesCBL-M12(FF5P)/OPEN-100IP67A-coded M12-to-5-pin power cable,IP67-rated5-pin female M12connector,1m CBL-M12D(MM4P)/RJ45-100IP67M12-to-RJ45cable,IP67-rated,1mCBL-M12DMM4PM12DMM4P-BK-100-IP67M12-to-M12Cat-5E STP Ethernet cable,4-pin D-coded M12connector,IP67,1m ConnectorsM12D-4PMM-IP67M12D-coded connector,QUICKON type,4-pin male,IP67M12D-4P-IP68D-coded screw-in sensor connector,male,IP68M12A-5P-IP68A-coded screw-in sensor connector,female,IP68,4.05cmM12Connector CapsA-CAP-M12F-M Metal cap for M12female connectorA-CAP-M12M-M Metal cap for M12male connectorDIN-Rail Mounting KitsDK-M12-305DIN-rail mounting kit for EDS-305-M12©Moxa Inc.All rights reserved.Updated May17,2023.This document and any portion thereof may not be reproduced or used in any manner whatsoever without the express written permission of Moxa Inc.Product specifications subject to change without notice.Visit our website for the most up-to-date product information.。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
M12网络端口，三层工业以太网交换机，EN50155嵌入式轨道交通专用插座示例：
M8系列插座
PGS-B9142ET-M12-C是网管型M12网络端口，三层工业以太网交换机，EN50155嵌入式轨道交通专用插座，CompactPCI板卡式冗余环网交换机。
前面板带有6个10/100/1000Base-T(X)M12接口。
后面的CPCI接口有8个10/100/1000Base-T(X)以太网接口。
是特别为轨道交通行业EN50155标准要求而设计的坚固型交换机。
它同时具有以下特性：
●支持2线以太网距离扩展端口，节约布线成本。
●介质冗余协议(MRP)允许环网中的交换机在信号失效时快速恢复。
在生成树协议的网络中取得更快的恢复时间。
●提供高级IP-based带宽管理功能：可以现在每个IP设备的最大带宽用户可以在使用IP摄像机和NVR是通过带宽管理，给他们提供更大的带宽。
●支持应用级QoS功能：应用级QoS功能可以按TCP/UDP端口给数据流设置不同的优先级
●Device Binding功能：设备绑定功能只允许制定的MAC地址访问网络，在没有许可时其他人是无法访问网络的。
它可以有效防止未经授权进行网络访问的行为。
.
●高级DOS/DDOS自动防护功能：如果IP泛洪行为短时间内突然增大交换机将锁定源IP地址一段时间以防范攻击。
它是硬件级别的防护，因此可以立即启用，即刻防护DOS/DDOS攻击.
●TCP/IP网络Modbus协议
●IEEE802.3az节能以太网技术:允许在数据量少时减低硬件功耗。
减少50%以上的电力消耗，同时保持与现有设备的兼容性。
●支持以太网冗余协议MSTP（RSTP/STP兼容），可以让关键应用在网络通讯中断或短时故障时快速恢复通讯。
●宽温工作温度为-40°C到70°C可以满足严苛的工业环境需求。
同时提供Telnet和console(CLI)配置方式,
为保障车载CBTC系统信息传输的可靠性，在车载CBTC系统中采用CPGS-B9142ET-M12-C交换机，以配合车载ATC计算机的应用。
该交换机安装在车载ATC计算机里面，用来传输车载ATP等重要信号数据，CPGS-B9142ET-M12-C交换机部分端口可通过CPCI背板引出。
CPGS-B9142ET-M12-C满足TTDP列车拓扑发现协议。
在车头和车分别部署两台CPGS-B9142ET-M12-C，传输距离可达100~300米，中间不需要再额外部署交换机，减少故障点并提高传输效率。
TTDP（列车拓扑发现协议）为提高轨道交通网络配置的效率而开发。
该协议允许网络交换机在网络拓扑结构发生改变后自动与其他网络设备进行协商，并将根据新的列车车厢的指令为网络设备分配一个IP地址。
网络管理员或者其他运营人员不需要重新手动配置网络设备。
有了这项技术，列车操作人员可以很大地改进他们的运营效率并将配置错误减少到最低。
该系统同时具有Bypass硬件旁路功能，当一个节点出现故障了，系统很快找到另一条路径并继续运行，保证网络连接不间断。
M12系列插座
M12智能以太网交换机插座是适用于IA工程师及自动化机器制造商的理想，可确保网络契合工业 4.0的应用需求。
智能交换机将助力机器和控制柜焕发新的生机，由于安装和配置简便，可简化日常工作任务。
此外，该交换机能够被监测，而且在整个生命周期中均可轻松维护。
SDS-3008交换机支持最常用的自动化协议，包括EtherNet/IP、PROFINET和Modbus/TCP等，让用户可通过自动化HMI实现可控性及可视性，从而提升运行性能及灵活性。
该交换机还支持一系列实用的管理功能，包括IEEE802.1Q VLAN、端口镜像、SNMP和通过继电器发出警告等。
.
工业以太网交换机主要是应用于复杂的工业环境中的实时以太网数据传输。
以太网在设计时，由于其采用载波侦听多路复用冲突检测(CSMA/CD机制)，在复杂的工业环境中应用，其可靠性大大降低，从而导致以太网不能使用。
工业以太网交换机采用存储转换交换方式，同时提高以太网通信速度，并且内置智能报警设计监控网络运行状况，使得在恶劣危险的工业环境中保证以太网可靠稳定的运行。
工业以太网交换机在工业级设计一般在设计上满足:工业宽温设计，3级电磁兼容设计，冗余交直流电源输入，另外PCB板一般做"三防"处理。
工业现场的环境比普通环境都要恶劣，至少在震动，湿气，温度上都要比普通环境恶劣，普通交换机在设计上没有抵御在工业环境中出现的各种情况的能力，普通交换机不能长时间工作在这种恶劣环境下，经常容易出现故障，更使维护成本上升，一般不建议在工业环境中使用商业交换机，为了能使交换机在这种恶劣环境中使用，故生产出能适应这种环境的交换机，工业级别的交换机的可靠性有电源故障，端口中断，可由继电器输出报警，冗余双直流电源输入，主动式电路保护，过压、欠压自动断路保护。
特点
1、高性能以太网交换机技术，保证以太网通信速度
2、IEEE802.3/802.3d/802.3u/802.3x，存储转换交换方式
3、具有抑制广播风暴功能、端口链路告警信息、电源故障信息继电器输出功能
4、采用12~48VDC双冗余电源供电
5、工作温度-10~+60℃(常温)，-40~+85℃(宽温)
6、采用金属外壳，一般为铝合金外壳。
防护等级IP40。
7、10Base-T/100Base-TX自适应的以太网接口，MDI/MDI-X，全双工/半双工自适应
接口特性:支持IEEE802.3、IEEE802.3x、IEEE802.3d、IEEE802.3u标准
电气接口:支持多个10Base-T/100Base-TX以太网接口，MDI/MDI-X，全双工/半双工自适应支持功能传输方式:存储转发方式
工作方式:异步工作,点对点或多点,2线半双工
传输距离:小于100米
安装尺寸:支持壁挂式，导轨式，机架式安装
使用环境:工作温度:-40℃~+85℃，存储温度-45℃-80℃:工作湿度:5%-95%
传输速率:转发速度:148810bps，系统交换带宽:4.8G，最大过滤速度:148810bps，
支持4K以上MAC地址表
保护等级:IP40，工业级标准设计，波纹式高强度金属外壳
电源特性:12V、24V、48V直流输入双电源冗余备份
优势：
互联、设备的冗余以及设备的实时等;而性能上的区别则主要体现在适应外界环境参数的不同。
工业环境除了有很多如:煤矿、舰船等特别恶劣的环境外，还有在EMI(电磁兼容性)、温度、湿度以
及防尘等方面有特殊要求的环境。
其中温度对工业网络设备的影响面是最广泛的。
折叠编辑本段注意事项
(1)不要将设备放置在接近水源或者潮湿的地方;
(2)电源电缆上不要放任何的东西，将其放在碰不到的地方;
(3)为了避免火灾，不要将电缆打结或者包住;
(4)电源接头以及其他设备连接件需要连接牢固，并经常检查线路的牢固性;
(5)保持光纤插座和插头的清洁，设备工作时，不要直视光纤的断面;
(6)注意设备清洁，必要时可以用棉布擦拭;
(7)设备出现故障时，为了安全起见不要自己维修。
应用领域
工业以太网交换机市场主要应用在电力自动化、工厂自动化、煤矿自动化、轨道交通、风能风电等领域，其次是冶
金，石油石化，道路交通控制自动化，楼宇自动控制系统，油田控制自动化，水电站控制自动化，机房监控系统，水利监控，环保监控等工控自动场所。
工业以太网交换机以其较高的防护等级(一般IP40)、较强的电磁兼容性(EMS4级)、稳定的工作性能而应用在一些环境条件苛刻的工业现场，为工业通信提供有力的保障。