集装箱加固件词汇
集装箱船加固件英语专用词汇
集装箱船加固件英语专用词汇集装箱绑扎件Container lashing equipment船用集装箱紧固件Container securing fitting for ships埋入式底座Flush Sockets Flush iso foundatons带孔底板Double Plate立式底座Raised Foundations燕尾底座Dovetail Foundation / Dovetail plates锥头Welding coneD型环D-ring D型座Breech D-ring Removable D-ring Flush D-ring 梅花底座Round sockets圆底座Round Socket眼板Lashing Eyes / Lashing plates导锥Guide Cone导座Guide fittings窝座Lashing pot花篮螺丝Turnbuckle拉杆Lashing Bar / Lashing rods接长杆Eye hook extension rod/ knob extension rod单锥Single stacker横向双锥Double Stacker纵向双锥Double Stacker安全单锥Hanging Stacker / Lockable stacking cones扭锁Manul Twistlock半自动钮锁Semi-automatic Twistlock中间钮锁Intermadiate Twistlock底部固定扭锁Fixed base twistlock中间锁Midlock燕尾底锁Dovetail Twistlock底锁Bottom Twistlock圆形底锁Breech twistlocks / round twistlock侧开底锁Side twistlocks桥锁桥码桥型连接器Bridge Fitting支撑Pressure elements/supports波浪杆Crinkle bar企鹅钩Penguin hook象脚Elephant foot吊座Lifting Socket拉索steel wire rope / steel wire handle活动头Swivel Head半自动锁拉锁wire rope for semi-automatic twistlock便携式系固设备（portable securing device）（1）系固链条（lashing chain）及紧链器（Tension lever）（2）钢丝缆lashing rod lashing bar集装箱绑扎杆（4）卸扣Shackle集装箱绑扎件埋入式底座（imbed foundation）主要用于仓底，也有用于仓盖上，单埋入式、埋双埋入、纵双埋入和四联埋入imbed foundation Flush Sockets Flush iso foundaton立式底座突出底座Foundation Raised foundations。
集装箱术语词汇表
集装箱术语词汇表附录A 术语词汇表下⾯是集装箱构件及其损坏和磨蚀形态⽅⾯的术语词汇表，以英语字母顺序依次列出，其中包括对于⽂件化要求有关的术语（包括缩写）的解释。
抗变形装置（Anti- Rack Device )通常装在箱门上对箱门和门框起增加强度及刚性作⽤的⾦属构件。
装有这种装置的集装箱能经受更⼤的横向扭⼒。
弯曲（Bend)结构件上的⼀种变形。
构件发⽣这种变形时，与原来设计的形状相⽐，其⽅向出现了急剧的变化。
铰链板（Blade )⽤焊接和螺栓连接⽅法永久安装在箱门上的铰链构件。
底架（Bottom Frame 或Understructure )⽀承地板、箱⾯板和⾓柱的底部框架。
底（侧）梁（Bottom ( Side ) Rail在前后框架之间沿集装箱下侧纵向排列的结构件。
⼸形（Bow )构件上沿整个长度⽅向上的⼀种渐进性（⾮急剧性）变形，变形垂直于长度⽅向。
破损（Broken )断裂成两块或更多的碎块。
衬套（Bushing )套在转轴上的管状零件，起减少旋转摩擦阻⼒和降低电解腐蚀的作⽤。
密封胶（Caulking 或Sealant )⽤于填塞所有连接间隙及铆接缝隙以确保⽔密效果的材料。
在⽊地板边缘、箱的两侧及端部框架之间要施打密封胶。
中梁（Center Spacer )在移安装胶合⽊地板的集装箱中可以见到这种型钢。
该型钢从后槛⾄前槛（或到鹅颈槽主横梁）分布在集装箱中央，沿纵向中线将地板分为两部分。
该型钢常为‘帽型’结构，但在某些集装箱中也有使⽤平型梁来实现同样的中央隔开功能的。
底盘车（Chassis )⼀种专为运输集装箱⽽制造的车辆。
当底盘车与集装箱联为⼀体时，整个部分与运货拖车具有相同的功能。
综合资料牌（Consolidated data Plate )⼀块固定在箱门上的矩形板，上⾯含有适⽤于⼀种以上公约、规则或其他的证书信息。
集装箱（Container )⼀种尺⼨标准化的矩形设备，设计⽤于装运组合货物、包装货物或散货，能适应不同种类运输⽅式的快速转换（本指南中的“集装箱”⼀词除另有注明者外，指的是⼲货箱即封闭型集装箱，其装货空间在集装箱装货时处于封闭状态，能防⾬⽔渗漏）。
集装箱专用词汇中英文对照表(内部参考)
序号
中文名称
英文名称
1
生产制造
Fabrication
2
组装
Building
3
剪切
Shearing
4
切断
Cutting
5
压
Pressing
6
压弯
Bending
7
冲压
Punching
8
成型
Forming
9
一次打砂
1stShot Blasting
10
车间底漆
Shop Priming
Corner Floor Support
16
底角板
Bottom Support Angle
七、侧墙Side
1
侧板
Side Wall
Side Panel
2
边侧板（大四波板）
Side Wall Outer
End Panel
Edge Side Panel
3
大内侧板（四波板）
Main Panel
Side Wall Inner (Large)
17
把手座
Handle Guide
Handle Hub
18
把手座铆钉
Handle Guide Rivet
Handle Hinge Pin
19
把手铰链
Handle Hinge
20
把手锁件
Handle Retainer
21
把手锁件垫片
Handle Retainer Spacer
22
锁头
(Gear)Cam
21
焊机
Welding Equipment
集装箱英语
Gasket. Hinge Blade Retainer Gasket. Large Bearing Bracket Gasket. Small Bearing Bracket Gasket. Retainer Plate Gasket. T.I.R. Plate-B Hinge Blade Retainer Tapped Metal Plate Large Bearing Bracket Tapped Metal Plate Small Bearing Bracket Tapped Metal Plate Retainer Plate Tapped Metal Plate T.I.R. Plate Tapped Metal Plate-B Corner Reinforcement Door Bumper Tapping Screw
７
８ ９
Cross Member
Bottom Side Rail Lower Forklift Pocket
底横梁
底侧梁下 叉车槽
→ Rear Frame(一) 后端框
１ ２ ３ ４ 5 6 7 8 9 10 11 12 13 14 15 Hinge Lug Cam Keeper Corner Casting Rear Corner Post (Outer) Rear Corner Post (Inner) Door Sill (Outer) Door Sill (Inner) Reinforcement Plate Door Sill Stiffener (Lower) Door Sill Stiffener (Upper) Door Header (Outer) Door Header (Inner) Door Header Stiffener Roof Gusset Door Sill Timber 铰链搭子 锁座 角件 后角柱(外) 后角柱(内) 门槛(外) 门槛(内) 加强板 门槛加强板(下) 门槛加强板(上) 门楣(外) 门楣(内) 门楣加强板 箱顶加强板 门槛木枕
[精华]集装箱英语术语
![[精华]集装箱英语术语](https://img.taocdn.com/s3/m/8b5deba6dc88d0d233d4b14e852458fb770b38b9.png)
[精华]集装箱英语术语Container-related Expressions 集装箱相关术语TEU Twenty-Foot Equivalent Unit / Twenty-Foot container ( 20’GP) 20尺标箱FEU Forty-Foot Equivalent Unit./ Forty-Foot equivalent equals/ container(40’GP)40尺标箱rack container/ flat rack container (FR) 框架箱 open top (OT) 开顶箱Platform Container (PF) 平板箱HC/HQ(high cube)高箱tank container 油罐集装箱reefer container/ refrigerated container (RF) 冷藏集装箱 dry container/ dry freight container (DC) 干箱corner fitting 角件corner post 角柱corner flitting 角配件cross member 底梁door hinge 门锁链door holde 门钩door licking handle 门把手handle lock 把手锁件door lock rd 门锁杆door meander 门媚door sheet 门板door sil 门栏l front lining 端壁内衬板roof 箱顶roof bows 顶板梁roof sheet 顶板dunnage lumber 垫料bull ring(D Ring)箱内稳货环 reefer draws power/ power pack 冷箱发电机 container accessories and parts 集装箱配件container leasing 集装箱租赁round trip lease 往返租赁one-way lease 单程租箱container leasing long-term 集装箱长期租赁 container leasing short-term lease 集装箱短期租赁 period of container leasing 租箱期 off-hire containers 退租箱container inspection/ survey 集装箱检验container maintenance 集装箱维修 container modification 集装箱改造container transportation 集装箱运输 container packing 集装箱装箱temperature and humidity 集装箱箱内气体、温度、湿度container cleaning洗箱cracked 裂痕dent 凹进bend 弯曲bow 压弯container wear and tear 集装箱箱体自然损耗container cubic 集装箱容量 efficient of container 集装箱箱容系数container internal volume 集装箱内容积 container dimensions 集装箱尺寸container’s internal dimensions/ inside dimension (I.D.) 集装箱箱内尺寸container’s overall external dimensions/ outside dimension 集装箱箱外尺寸container height 集装箱高度 container length 集装箱长度 container width 集装箱宽度 container load weight 集装箱载重量 container weight 集装箱重量 type of container 集装箱规格 strength of container 集装箱强度Container No. 箱号container carrier集装箱运输车 container carrier truck集装箱载运汽车container chassis集装箱底盘车 container trailer集装箱拖车 container semi-trailer集装箱半挂车 container car集装箱专用车fork truck for lifting container 集装箱叉车 container handler 集装箱搬运车 container carrying vessel 集装箱船equipment control (E/C) 箱管 cargo interests 货主forwarder 货代ISO Standard for Container 国际标准集装箱规格 container depot/ yard (YD) 集装箱堆场 less than container load (LCL) 拼箱shipper’s own container(SOC) 货主自备(有)箱carrier’s own container(COC) 船东自备(有)箱。
集装箱英语术语
Container-related Terms 集装箱相关术语fleet of containers 集装箱箱队E/C Equipment control 箱管TEU Twenty-Foot Equivalent Unit is the value of 1 twenty-foot container. ( 20’GP) 20尺标箱FEU Forty-Foot Equivalent Unit. 1 Forty-Foot equivalent equals （40’GP）2 Twenty-Foot containers. 40尺标箱Corner Fitting 角件Corner Post 角柱End Wall/Side Wall 端墙/侧墙Bull Ring（D Ring）cargo-securing devices mounted in the floor of containers 箱内稳货环Container No。
箱号Seal metal strip or lead fastener used for locking freight car 箱封Seal record a record of the number，condition and marks of identificationon seals made at various times and places，referring to themovement of the container between origin and destination 箱封检查记录Collection and Distribution Transport 拼箱分拨运输SL&C Shipper’s Load and Count 货主装箱、点数SP & S Shipper’s Pack and Seal 货主装箱、加封SOC Shipper’s Own Container （SHIPPER OWNED CTN）货主自有箱The maintenance of a sufficient quantity of containers may beexpensive, but may prove to be worthwhile in the long run,depending on the trade volume. In cases, shippers may purchasefrom the market the used container to send the cargo with, justfor once and keep the container for a makeshift warehouseafter its delivery or for some other use at destinationCOC Carrier’s Own Container（CARRIER OWNED CTN）船东自有箱From others’ point of view, containers for a specific carrier’s use are allcalled COC. Therefore, the carrier’s leased in containers are also his COC. Equipment change 换箱GP General Product ( Dry Cargo ) Container 干货箱DC Dry Cargo Container 干货箱Garmentainer 挂衣箱GOH Garment on Hanger 挂衣箱HC/HQ HI-CUBE （HIGH CUBE）Container Any container whichexceeds 8 feet 6 inches in height，usually 9’6’’ 高箱40 TH 40’ TIE High Cube 40尺高箱40 GH 40’ G arment High Cube 40尺挂衣高箱40’/45’ HI-CUBE CONTAINER SURCHARGE 40’/45’高箱费All-in Rate/40’ x 1.125 ( for 40’ HC ) 海运费计收All-in Rate/40’ x 1.266 (for 45’ HC )FR Flat Rack Container 框架箱OT Open Top 开顶箱PF （Platform Container）平板箱RF Refrigerated Container 冷藏箱COLLAPSIBLE CONTAINER（FR 框架）折叠式集装箱DG Container Dangerous Goods Container 危险品箱Controlled Atmosphere an atmosphere in which oxygen, carbon dioxide and nitrogen concentrations are regulated, as well astemperature and humidity. 箱体内气体、温度、湿度调控Empties Empty containers are provided by ship operatorsto cargo owners at container depots. Appropriatecharges are made for the lease of their ownership. 空箱Genset a portable power generator, which convert fuel intoElectrical power by mechanical means, and from whichA reefer draws power. （手提式/轻便）冷箱发电机Power Pack 供冷箱用的小型发电机（可租用）Container Cleaning 洗箱VEN Ventilated 通风FRZ Frozen 冰冻HTD Heated 加热I.D. Inside Dimension 箱内尺码Inside Measurement 箱内尺码TW ( TARE WEIGHT ) The weight of an empty container 箱子皮重Container Leasing Co。
集装箱术语——精选推荐
集装箱术语FCLFull Container Load整柜LCLLess Than Container Load 拼箱40 HC40’ High Cubic40高柜40 HRF40’ High Refrigerator40高冻柜G.CGeneral Cargo普通柜S.HSemi Hazardous半危险品H.ZHazardous危险品O/TOpen Top开顶柜F/RFlat rack框架箱R.FRefrigerator冻柜CYContainer Y ard集装箱堆场CFSContainer Freight Station集装箱处理站TEUTwenty-feet Equivalent Units20英尺集装箱FEUForty-feet Equivalent Units40英尺集装箱A/WAll Water全水路（主要指由美国西岸中转至东岸或内陆点的货物的运输方式）MLBMini Land Bridge迷你大陆桥（主要指由美国西岸中转至东岸或内陆点的货物的运输方式）二、主要船务术语Carrier船公司NVOCCNon-V essel OperatingCommon Carrier无船公共承运人Booking Sheet订舱单S/OShipping Order装货通知书Shipper发货人Exporter出口商Consignee收货人Notify Party通知人Port of Loading装运港Port of Discharge卸货港Place of Delivery交货地B/LBill of lading提单Original B/L正本提单Copy B/L副本提单Shipped on Board B/L已装船提单Received for Shipping B/L收迄待运提单或待运提单Direct B/L直达提单Through B/L联运提单或称转船提单MT B/LMultimode Transport B/L多式联运提单Liner B/L班轮提单Clean B/L清洁提单Foul B/L不清洁提单House Bill of Lading货运提单MB/LMaster Bill of Lading船东提单MTDMultimode Transport Document多式联运单据W/TWeight Ton重量吨（即货物收费以重量计费）M/TMeasurement Ton尺码吨（即货物收费以尺码计费）W/MWeight or Measurement ton即以重量吨或者尺码吨中从高收费ETDEstimated time of departure预计开船时间ETAEstimated time of arrival预计到达时间三、运输费用常用术语英文缩写英文中文O/FOcean Freight海运费BAFBunker Adjustment Factor燃油附加费BAFBunker Surcharge or BunkerAdjustment Factor燃油附加费Y ASY en Appreciation Surcharge日元增值附加费Y ASY ard Surcharges码头附加费ORCOrigin Receiving Charge码头附加费DDCDestination Delivery Charge目的港码头附加费（美国）PSSPeak Season Surcharge旺季附加费GRIGeneral Rate Increase旺季附加费THCTerminal Handling Charge码头处理费CAFDevaluation Surcharge orCurrency Adjustment Factor货币贬值附加费PCSPort Congestion Surcharge港口拥挤附加费EPSEquipment PositionSurcharges设备位置附加费DOCDocument charges文件费Deviation Surcharge绕航附加费Suez Canal Surcharge苏伊士运河附加费Transshipment Surcharge 转船附加费Direct Additional直航附加费Port Surcharge港口附加费Heavy-Lift Additional超重附加费Long Length Additional超长附加费Cleaning Charge洗舱费Fumigation Charge熏蒸费Ice Surcharge冰冻附加费Optional Fees or Optional Additional 选择卸货港附加费Alteration Charge变更卸货港附加费运输条款中CY/CY、CY/FO、CY/LO解释1. CY/CY是指堆场到堆场方式，承运人在装货港集装箱堆场接收整箱货物并负责运至卸货港集装箱堆场整箱交付收货人；2. CY/FO（free out）承运人在装货港集装箱堆场接收整箱货物并负责运至卸货港但不负责卸货；3. CY/LO(line out)承运人在装货港集装箱堆场接收整箱货物并负责运至卸货港卸货；4. CY/TACKLE承运人在装货港集装箱堆场接收整箱货物并负责运至卸货港卸货至接货车上；5. CY/HOOK承运人在装货港集装箱堆场接收整箱货物并负责运至卸货港卸货，此处当吊臂吊下货物后服务终止。
集装箱专用词汇中英文对照表
集装箱专用词汇中英文对照表(内部参考)版本号：200001日期：Tuesday, May 23, 2000南通中集顺达集装箱有限公司目录一、生产制造二、门端、后端三、锁杆装置四、铰链五、紧固件六、前端七、侧墙八、顶部九、底部十、焊接十一、打砂十二、油漆十三、地板十四、密封胶十五、门封十六、材料、部件十七、机器设备、工具十八、试验十九、标贴二十、缺陷及维修二十一、其他二十二、罐箱一、生产过程Producing Process1生产制造Fabrication 2组装Building3剪切Shearing4切断Cutting5压 Pressing6压弯Bending7冲压Punching 8成型Forming9一次打砂1st Shot Blasting10车间底漆Shop Priming 11部装Sub Ass’y 12总装Main Ass’y 13二次打砂2nd Shot Blasting14喷漆Painting15完工Finishing 16开卷Decoiling二、门端Door End 后端Rear, Rear End1门板Door Panel2门端框 Door Frame3门楣Door Header4门楣加强板 DoorHeader GussetDoor HeaderWeb Door Header Patch5门楣板 Door Header CapDoor Header ExtensivePlate6门槛Door Sill7门槛加强板 Door SillGusset Door Sill Web DoorSill Patch8门槛封板Rear CornerCover Plate9后角柱 Rear Corner Post10后角柱加强板RearCorner Post Stiffener11内角柱Rear Corner PostInner12内角柱垫板RearCorner Post Inner Spacer13外角柱Rear CornerPost Outer J-Bar14角件Corner CastingCorner Fitting15门拉筋Lashing Bar16槽钢Channel Section17门横梁Door HorizontalMember18门竖梁Door VerticalMember19门中竖梁DoorVertical Member Center20门边竖梁DoorVertical Member Side21门竖梁封板Door FrameCover Plate22封板Cover Plate23角结构Corner Structure24后下角海关封板RearBottom Corner TIR Filler25门档板Stopping PlateDoor Button26绳Rope Tie Rope27绳环Tie Down Chain三、锁杆装置Locking Device1锁杆Locking Rod2托架Bearing Bracket3大托架组件 LargeBracket Ass’y4大托架外Large BracketOuter5大托架内Large BracketInner6小托架组件 SmallBracket Ass’y7托架垫片BearingBracket Back Up Plate8托架衬套（指塑料或尼龙衬套）Bearing Bush9托架盖搭扣（Custom）Catch10托架座锁牌（Custom）Seal Plate Handle RetainerBack Up Plate11搭扣衬套Bush12大托架密封垫（指橡胶密封垫片）Large BracketGasket13小托架密封垫（指橡胶密封垫片）SmallBracket Gasket14把手Handle15锻造把手Forged Lever16压型手柄Pressed Lever17把手座HandleGuide Handle Hub18把手座铆钉HandleGuide Rivet Handle HingePin19把手铰链Handle Hinge20把手锁件HandleRetainer21把手锁件垫片HandleRetainer Spacer22锁头（Gear）CamLocking Cam23锁座（Gear）CamKeeper24垫片Pad Shim四、铰链Hinge1铰链Hinge Blade2门耳朵 Hinge LugHinge Gusset3铰链销 Hinge Pin4铰链衬套Hinge PinBush5铜 Bronze6尼龙Nylon7铰链垫片Hinge Washer五、紧固件Fastener1铆钉Rivet2抽芯铆钉Blind Rivet3开花铆钉Drive Rivet4索钉Huck Bolt5螺栓Bolt6螺母Nut7弹簧垫圈Spring Washer8圆头螺栓Round HeadBolt9六角头螺栓 HexagonHead Bolt10索钉套Huck Collar 11锁紧螺栓Lock Bolt12弹性Elasticity13扭矩Torque六、前端Front, FrontEnd1前墙Front Wall FrontPanel2端框End Frame3前端上梁/前楣FrontTop End Rail Front Header4前楣板 Front HeaderCap5前端下梁前槛FrontBottom End Rail FrontSill6前端下梁加强板 FrontSill Web Front BottomRail Patch7前角柱 Front CornerPost8前角柱加强板FrontCorner Post Stiffener9前拉筋 Lashing Bar10槽钢防撞槽钢ChannelSection Protection ChannelCone Damage Protector11前槽封Cover Plate12角件Corner Casting13底角加强板Bottom Corner Stiffener14木板支撑Floor Support 15底角封板Corner Floor Support16底角板Bottom Support Angle七、侧墙Side1侧板Side Wall Side Panel2边侧板（大四波板）Side Wall Outer End Panel Edge Side Panel3大内侧板（四波板）Main Panel Side Wall Inner ( Large )4小内侧板（三、二波板）Side Wall Inner ( Small ) 5顶侧梁 Top Side Rail （迷宫型）通风器(Labyrinth Type ) Ventilator7绳勾Lashing Ring Tie Hook Rope Holder八、顶部Roof1顶板Roof Panel2顶角保护板/顶角加强板Roof Corner Protection Plate Roof Corner Gusset Top Corner Reinforcement 3顶前加强板 Front Roof Gusset4顶后加强板 Rear Roof Gusset九、底部Base1底架Base Structure 2底侧梁 Bottom Side Rail 3底侧梁加强板Bottom Side Rail Reinforcement4底侧梁角撑/地板支撑底角撑Bottom Side Rail Angle Floor Support Angle 5底横梁 Cross Member6宽边底横梁 Wide Cross Member7底短梁 Outrigger Tunnel Outrigger8底横梁加强板Cross Member Gusset CrossMember Web CrossMember Patch9地板中梁Floor CenterRail10地板中梁封板FloorCenter Rail TIR Patch11地板中梁橡胶塞FloorRail Plug Rubber12叉槽Fork Lift Pocket13叉槽顶板Fork LiftPocket Top Plate ForkLift Pocket Upper Plate14叉槽底板Fork LiftPocket Bottom Plate ForkLift Pocket Lower Plate15叉槽加强板ForkLift Pocket Reinforcement16叉槽侧梁Fork LiftPocket Side Rail ForkLift Pocket Side Member17鹅颈槽GooseneckTunnel18鹅颈大梁，鹅颈（槽）后梁Tunnel Bolster19鹅颈（槽）后梁加强板Tunnel Bolster GussetTunnel Bolster Web20鹅颈小梁，鹅颈背梁Tunnel Bow21鹅颈盖板Tunnel Plate22鹅颈侧梁Tunnel SideRail十、焊接Welding1焊接Welding2电弧焊 Arc Welding3手工电弧焊 ShieldedMetal Arc Welding4气体Gas5二氧化碳气体保护焊CO2Gas Metal ArcWelding6自动焊 Auto Welding7半自动焊Semi AutoWelding8手工焊 Manual Welding9平焊Flat Welding10横焊HorizontalWelding11立焊Vertical Welding12仰焊OverheadWelding13点焊Tack Welding14对接焊Butt JointWelding 搭接焊15周围焊AroundWelding16跳焊Skip Welding17间断焊StitchWelding18连续焊ContinuousWelding19焊缝Welding SeamWelding Line WeldingBeam20背面焊缝Back Bead21焊机WeldingEquipment22焊丝Welding Wire23焊条Welding Rod24电焊条Electrode25焊条夹ElectrodeHolder26引弧板End Tab27渗透,渗透率Penetration,penetration rate28百分之xxxx xxxxPercent29气割Oxygen Cutting30熔合,未熔合Fusion,incomplete fusion十一、打砂Shot Blasting1打砂抛丸喷砂 ShotBlasting2一次打砂零部件打砂1st Shot Blasting3二次打砂整箱打砂2nd Shot Blasting4钢砂Shot Ball5棱角砂 Grit6金属切丸钢丝切丸Cut Wire7去油脂 Degreasing8喷吹Blowing9粗糙度 ProfileRoughness10密度覆盖度DensityCoverage11清洁度Cleanliness十二、油漆Painting1油漆喷涂 PaintingPaint Spraying2表面预处理 SurfaceReservation3预处理 Pretreatment4车间底漆Shop Primer5富锌底漆Primer6环氧富锌漆 Epoxy ZincRich Primer7中间漆 Middle Coating8面漆Top Coating9沥青漆底架漆BitumenUnder Coating10基料PTA（Base）11固化剂PTB（CuringAgent）12稀释剂Thinner13喷漆房Painting Booth14烘房Dry Booth DryOven15停留房流平房 SettingBooth16干膜厚度Dry FilmThickness ( D.F.T. )17湿膜厚度Wet FilmThickness ( W.F.T. )18油漆表膜厚仪 FilmThickness Gauge19喷枪Spray Gun十三、地板Flooring1地板Floor2沉头的埋头的Countersunk3地板角铁底角撑Floor Guide Rail4含水量 Moisture Content5湿度计 Moisture Gauge6地板清漆Varnish7地板钉油地板钉头漆Polyurethane ResinProtective Resin8自攻螺钉Self Tapping Screw9上漆地板Urethane Coated Plywood Floor10地板安装Plywood floor installation十四、密封胶Sealant1丁基密封胶 Butyl Sealant2氯化密封胶 Chloroprene Sealant3硅胶Silicon Sealant十六、材料、部件1母材Base metal2材料Material3零部件 Component4原材料 Raw Material5科碳钢 Corten （SPA-H）6碳素钢 Mild steel7钢板Steel Sheet8不锈钢 Stainless Steel9波纹Corrugation10斜面Slope11波度Waviness12方管Square Tube13平板Flat14扁铁Flat Bar15金属Metal16铁Iron17塑料Plastics18电镀锌板Electrically Zinc Plate19热镀锌板Hot-Dipping Zinc Galvanized Plate20热轧Hot Roll21冷轧Cold Roll十七、机器、设备、工具1装配台 Ass’y Die2电动葫芦Electric Hoist 3千斤顶 Jack4装配架 Jig5夹具Clamp6模具Die Mould7输送机 Conveyor 8托辊输送机 RollerConveyor9校平机 Leveller10折弯机Press Brake11罗拉机辊压成形机Roller Roll FormingMachine12剪切机ShearingMachine13开卷机Slitter14喷砂机Blaster15冲床Punch Press16拖车Chasis17吊车Crane18叉车Fork Lifter19电机Motor20液压缸HydraulicCylinder21泵Pump22手锤ChippingHammer23砂轮机Grinder24砂轮Grinding Wheel25钢丝刷Wire Brush26锤子Hammer27手电钻Hammer Drill28接点夹Joint Keeper29木锤Mallet30磁力钻Magnet Drill31喷枪Spray Gun32喷嘴Nozzle33橡胶锤UrethaneHammer34铆钉枪Rivet Gun35焊枪Welding Torch36压实机（打锁杆螺栓用）Compactor Machine十八、试验Test1尺寸检查DimensionalCheck2地板强度试验FloorStrength Test3端板强度试验EndWall Strength Test4底角件起吊试验 LiftingFrom Bottom CornerFitting5顶角件起吊试验 LiftingFrom Top Corner Fitting6叉槽起吊试验ForkLift Pocket Lifting Test7拉伸试验Lashing Test8漏光试验Light Leak Test9纵向刚性试验Longitudinal Racking Test10横向刚性试验Transverse Racking Test11栓固试验RestrainTest12顶板强度试验RoofStrength Test13侧板强度试验SideWall Strength Test14堆码试验StackingTest15内部纵向刚性Internallongitudinal restraint16内部横向刚性Internallateral restraint17水密试验Watertightness18风雨密试验Weatherproofness19集中载荷Concentrated20均布载荷UniformlyDistributed21减速Deceleration22变形Deformation23永久变形PermanentDeformation24对角线Diagonal25方向Direction26力Force27开门尺寸Door Opening28内部Internal29外部External30量具Gauge31指示器Indicator32横向Transverse33纵向Longitudinal34公称尺寸NominalDimension35公差Tolerance36出始的Original37最大的Maximum38最小的Minimum39平行Parallel40位置Position41样箱试验Prototype Test42支撑Support43拉Tension44锁具Twist Lock45空载的Unloaded46试验小车Vehicle47游标卡尺VenireCalipers48屈服点Yield Point49垫块Pad50口径Aperture51推Compression52同心Concentric53偏心Eccentric 注：*为罐箱项目。
集装箱工件名称、术语中英对照
7
总装配线
Total assembly line
8
箱顶装焊线
Roof welding jig line
9
总焊接线
Full welding jig line
生产机械
1
冲压机 45吨
Power press 45 ton
2
冲压机 100吨
Power press 100 ton
10
侧板翻转焊
Side panel turning welding
生产线名称
1
门板线
Door line
2
门框装配线
Rear assembly line
3
前端装配线
Front assembly line
4
箱底装配线
Base assembly line
5
侧壁装配线
Side assembly line
6
箱顶装配线
2
侧板（中间板）
Side panel (inner)
3
侧上梁
Side top rail
4
通气孔盖
Ventilator
5
螺栓
Lock bolt
6
绑绳环
Lashing ring
7
箱门搭扣件
Rope ring
8
侧板组装
Side ass’y (assembly)
9
侧板自动焊
Side auto welding
集装箱工件名称、术语中英对照
工件名称
1
前角柱
Front corner post
2
前下梁
Front bottom rail
集装箱相关术语
集装箱相关术语fleet of containers 集装箱箱队E/C Equipment control 箱管TEU Twenty-Foot Equivalent Unit is the value of 1 twenty-foot container. ( 20’GP) 20尺标箱FEU Forty-Foot Equivalent Unit. 1 Forty-Foot equivalent equals （40’GP）2 Twenty-Foot containers. 40尺标箱Corner Fitting 角件Corner Post 角柱End Wall/Side Wall 端墙/侧墙Bull Ring（D Ring）cargo-securing devices mounted in the floor of containers 箱内稳货环Container No。
箱号Seal metal strip or lead fastener used for locking freight car 箱封Seal record a record of the number，condition and marks of identificationon seals made at various times and places，referring to themovement of the container between origin and destination 箱封检查记录Collection and Distribution Transport 拼箱分拨运输SL&C Shipper’s Load and Count 货主装箱、点数SP & S Shipper’s Pack and Seal 货主装箱、加封SOC Shipper’s Own Container （SHIPPER OWNED CTN）货主自有箱The maintenance of a sufficient quantity of containers may beexpensive, but may prove to be worthwhile in the long run,depending on the trade volume. In cases, shippers may purchasefrom the market the used container to send the cargo with, justfor once and keep the container for a makeshift warehouseafter its delivery or for some other use at destinationCOC Carrier’s Own Container（CARRIER OWNED CTN）船东自有箱From others’point of view, containers for a specific carrier’s use are all called COC. Therefore, the carrier’s leased in containers are also his COC. Equipment change 换箱GP General Product ( Dry Cargo ) Container 干货箱DC Dry Cargo Container 干货箱Garmentainer 挂衣箱GOH Garment on Hanger 挂衣箱HC/HQ HI-CUBE （HIGH CUBE）Container Any container which exceeds 8 feet 6 inches in height，usually 9’6’’高箱40 TH 40’TIE High Cube 40尺高箱40 GH 40’Garment High Cube 40尺挂衣高箱40’/45’HI-CUBE CONTAINER SURCHARGE 40’/45’高箱费All-in Rate/40’x 1.125 ( for 40’HC ) 海运费计收All-in Rate/40’x 1.266 (for 45’HC )FR Flat Rack Container 框架箱OT Open Top 开顶箱PF （Platform Container）平板箱RF Refrigerated Container 冷藏箱COLLAPSIBLE CONTAINER（FR 框架）折叠式集装箱DG Container Dangerous Goods Container 危险品箱Controlled Atmosphere an atmosphere in which oxygen, carbon dioxide and nitrogen concentrations are regulated, as well astemperature and humidity. 箱体内气体、温度、湿度调控Empties Empty containers are provided by ship operatorsto cargo owners at container depots. Appropriatecharges are made for the lease of their ownership. 空箱Genset a portable power generator, which convert fuel intoElectrical power by mechanical means, and from whichA reefer draws power. （手提式/轻便）冷箱发电机Power Pack 供冷箱用的小型发电机（可租用）Container Cleaning 洗箱VEN Ventilated 通风FRZ Frozen 冰冻HTD Heated 加热I.D. Inside Dimension 箱内尺码Inside Measurement 箱内尺码TW ( TARE WEIGHT ) The weight of an empty container 箱子皮重Container Leasing Co。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
集装箱船加固件英语专用词汇
集装箱绑扎件Container lashing equipment
船用集装箱紧固件Container securing fitting for ships
埋入式底座Flush Sockets Flush iso foundatons
带孔底板Double Plate
立式底座Raised Foundations
燕尾底座Dovetail Foundation / Dovetail plates
锥头Welding cone
D型环D-ring
D型座Breech D-ring Removable D-ring Flush D-ring 梅花底座Round sockets
圆底座Round Socket
眼板Lashing Eyes / Lashing plates
导锥Guide Cone
导座Guide fittings
窝座Lashing pot
花篮螺丝Turnbuckle
拉杆Lashing Bar / Lashing rods
接长杆Eye hook extension rod/ knob extension rod
单锥Single stacker
横向双锥Double Stacker
纵向双锥Double Stacker
安全单锥Hanging Stacker / Lockable stacking cones 纵向双锥Double Stacker
安全单锥Hanging Stacker / Lockable stacking cones 扭锁Manul Twistlock
半自动钮锁Semi-automatic Twistlock
中间钮锁Intermadiate Twistlock
底部固定扭锁Fixed base twistlock
中间锁Midlock
燕尾底锁Dovetail Twistlock
底锁Bottom Twistlock
圆形底锁Breech twistlocks / round twistlock
侧开底锁Side twistlocks
桥锁桥码桥型连接器Bridge Fitting
支撑Pressure elements/supports
波浪杆Crinkle bar
企鹅钩Penguin hook
象脚Elephant foot
吊座Lifting Socket
拉索steel wire rope / steel wire handle
活动头Swivel Head
半自动锁拉锁wire rope for semi-automatic twistlock 便携式系固设备（portable securing device）
（1）系固链条（lashing chain）及紧链器（Tension lever）
（2）钢丝缆lashing rod
（3）lashing bar集装箱绑扎杆
（4）卸扣Shackle 集装箱绑扎件
埋入式底座（imbed foundation）
主要用于仓底，也有用于仓盖上，单埋入式、埋双埋入、纵双埋入和四联埋入
imbed foundation/ Flush Sockets /Flush iso foundaton
立式底座突出底座Foundation Raised foundations。