360gps定位器使用说明书
GPS操作规程
GPS操作规程一、概述GPS（全球定位系统）是一种通过卫星定位技术来确定地理位置的系统。
本操作规程旨在规范GPS设备的使用和操作，确保正确、安全地使用GPS设备。
二、设备准备1. 确保GPS设备已充电并处于正常工作状态。
2. 检查GPS设备是否与导航软件或者应用程序连接正常。
3. 确保GPS设备的天线没有被遮挡，以获得最佳信号接收。
三、GPS操作步骤1. 打开GPS设备，并等待设备获取卫星信号。
2. 在设备菜单中选择导航功能，并输入目的地的地址或者坐标。
3. 确认导航路线后，开始导航。
4. 在行驶过程中，注意设备的屏幕显示，包括导航指示、距离、速度等信息。
5. 遵循设备的导航指示，按照设备提示的路线前进。
6. 在需要转弯或者改变方向时，提前注意设备的语音提示或者屏幕指示。
7. 如遇到交通阻塞或者其他导航变更情况，设备会自动重新规划路线，请及时遵循设备的指示。
8. 在到达目的地后，关闭导航功能，并关闭GPS设备。
四、注意事项1. 在使用GPS设备时，务必保持注意力集中于道路和交通安全。
2. 遵守交通规则，不要因为看GPS设备而分散注意力。
3. 在驾驶过程中，不要频繁操作GPS设备，以免影响驾驶安全。
4. 如遇到设备故障或者操作难点，请停车后再进行检查或者操作。
5. 定期更新GPS设备的地图和软件，以确保设备的正常运行和准确导航。
6. 在户外环境使用GPS设备时，注意防水和防震，避免设备受损。
7. 在长期不使用GPS设备时，应将设备存放在干燥、通风的地方，避免长期暴露在高温或者低温环境中。
五、常见问题解决1. 无法获取卫星信号：检查GPS设备是否处于开放空旷的区域，确保天线没有被遮挡。
2. 导航路线错误：检查输入的目的地地址或者坐标是否正确，或者重新规划路线。
3. 设备死机或者无响应：尝试重新启动设备，如果问题仍然存在，联系设备厂商进行维修或者更换。
六、总结本操作规程提供了GPS设备的使用和操作指南，匡助用户正确、安全地使用GPS设备进行导航。
GPS监控系统操作手册
2017—GPS车辆监控系统平台使用操作手册本监控平台前台支持HTML5的浏览器，请使用如firefox火狐浏览器54.0、chrome 谷歌浏览器59.0，微软IE11,360浏览8.0等。
登录后可见，平台由车辆监控，报表系统和用户设置组成。
一、车辆监控监控页面由左侧的模块列表，右侧的车辆列表，中间的地图和下方的状态栏组成。
模块列表包括：（一）实时监控、（二）轨迹回放和（三）条件查车。
1.1实时监控登录后，选中实时监控，如图：1.1.1车辆选择用户可以选择监控某台车，某几台车、或者所有车辆。
以下选择方式均可：1、选中一个或者几个车辆。
在下面的状态栏或者右侧分组栏对应的车辆名称前的小框内打勾，所勾车辆图标显示在地图上。
2、选中所有车辆：在状态栏的序号两字前方框内打勾，所有车辆显示在地图上。
3、选中某组车辆：在状态栏上方的工具条，点击“选择”，在弹出窗口内选择需要的组，再在状态栏上方序号左边打勾，所选所有车辆显示在地图上。
需要在地图上车辆图标上显示车牌号和当前速度，请在相应的框内打勾，如下图。
在实时监控中，车辆图标有默认的普通车标和圆点车标两种显示方式。
圆点车标的显示方式，主要用于车辆数量大，显示密集，需要了解密集分布程的情况，可以用于出租车辆是否发生无规律突然聚集的判断，同时可以用于表达出租车辆的空载和有客两种状态。
圆点图标显示车辆分布态势1.1.2车标图例1.1.3车辆状态选择根据车辆状态选择：本系统中用户可以根据车辆的状态进行选择，如全部车辆、在线车辆、离线车辆、报警车辆。
状态栏中当前显示的数据，如全部车辆、在线车辆、离线车辆、报警车辆都可以导出成EXCEL格式文件。
1.2车辆查询在系统中查找所关心的车辆，有以车牌号码（包括手机号车机号）查询和区域（包括矩形和多边形）查询两类方式：1.2.1车牌号码查询在状态栏中查询，如果要查询某一台车的数据，如粤CUD896，在查询栏中输入查询内容：再按【回车键】或者点击【查询按钮】，即可查出。
GPS操作规程
GPS操作规程一、引言GPS（全球定位系统）是一种基于卫星定位的导航系统，广泛应用于航空、航海、汽车导航等领域。
为了确保GPS设备的正常使用和操作，制定本操作规程，以指导用户正确操作GPS设备。
二、设备准备1. 确保GPS设备处于正常工作状态，电量充足。
2. 根据需要选择合适的GPS天线，并正确连接至设备。
3. 检查GPS设备的固件版本，确保已安装最新的软件更新。
三、开机与初始化1. 将GPS设备放置在开阔地区，确保设备能够接收到卫星信号。
2. 按下电源按钮，等待设备启动。
3. 在设备菜单中选择“初始化”选项，以获取卫星信号并确定当前位置。
四、基本操作1. 导航模式：选择导航模式以获取目的地的导航指引。
输入目的地地址或者坐标，设备将计算最佳路线并提供导航指示。
2. 地图浏览：通过地图浏览模式，可以查看当前位置、周边地图和地理特征。
可以缩放地图、切换地图视图等。
3. 路径记录：在需要记录路径的情况下，选择路径记录功能。
设备将记录行进轨迹，并提供相关统计信息。
4. 坐标标记：通过坐标标记功能，可以标记感兴趣的地点或者位置。
标记的坐标可以用于导航或者导出。
五、导航安全1. 在驾驶过程中，不要长期盯着GPS屏幕，以免分散注意力，应时刻保持注意力集中在道路上。
2. 遵守交通规则，遵循GPS设备提供的导航指引，但不要盲目依赖。
在特殊情况下，应根据实际道路情况进行判断。
3. 在导航过程中，及时注意设备的语音提示，以免错过导航指示。
4. 在使用GPS设备进行户外活动时，应注意天气状况、地形地貌等因素，确保安全。
六、设备维护1. 定期清洁GPS设备的屏幕和外壳，使用柔软的布擦拭，不要使用化学溶剂。
2. 避免将GPS设备长期暴露在高温或者低温环境中，以免影响设备性能。
3. 定期检查设备电池电量，确保充足。
长期不使用时，应将电池取出。
4. 如遇设备故障或者异常，应及时联系售后服务部门进行维修。
七、免责声明1. GPS操作规程仅供参考，用户在使用GPS设备时应自行承担风险。
北斗360电动车定位系统手机APP功能及操作方法
0
2
0
北斗360电动车定位系统手机APP功能及操
远程断电功能介绍
远程断电：经过数百次试验研发的远程断电执行设备可通 过手机远程断开/恢复电动车电路，远程断电后，电动车将 进入远程断电状态，无法加电，保证用户电动车能够有效的 防止盗抢。
具体操作：打开手机APP，登录账户后，点击下方“远程断 电”，进入“远程断电”，点击“远程断电”或“恢复通电 ”就可以实现电动车断电和恢复。
历史轨迹查询功能介绍
电子栅栏功能介绍
电子栅栏：当用户为电动车设置一个安全范围，比如100 米为安全范围，进出电子栅栏会发送报警信息。
具体操作：打开手机APP，登录账户后，点击下方“电子 栅栏，进入“电子栅栏”，然后选定一个范围，当电动车 出了这个范围，手机就会接到报警提示。
电子栅栏功能介绍
报警设置功能介绍
报警提示：北斗360电动车卫士具有断电报警、低 电报警、震动报警、出入电子栅栏报警等报警功 能，当用户电动车出现设备电量低、车辆震动、 出入电子栅栏时及时通知车主。
具体操作：进入APP，登录账号，点击“相关设 置”，点击“开启报警”，然后进入“报警设 置”，然后有多种选项，开启相应的报警设置。 比如开启“出电子栅栏”报警，当电动车出了设 置的电子栅栏范围，手机就会收到报警提示。
报警设置功能介绍
电动车生活功能介绍
电动车生活：北斗创新科技分享的一些关于电动车及电动 车定位器的知识和常识。
ห้องสมุดไป่ตู้
更多
更多APP功能尽请期待
感谢聆听
远程断电功能介绍
历史轨迹查询功能介绍
历史轨迹查询：自动记录电动车行驶记录，并将行驶数据通过GPRS上 传至北斗360·云计算中心，用户可通过手机回放永久性的行驶轨迹， 回放过程中可查看当时车速，方向，停留时间等信息。
GPS测绘使用手册(P360)
LI1C7200927序列号:R9D0-D1GJ激活码KBD6-KDK[序言亲爱的用户，GPS测绘软件是我公司总结当前市面上GPS导航软件的优缺点，结合用户使用的实际需求，经过我公司技术人员艰苦努力开发出的较为实用的导航软件,经过多次升级完善，软件最新的版本为2.0.0.2GPS测绘软件是基于WinCE平台，在嵌入式手机掌上电脑（MIO A700/ Mio A701）上使用的自导航定位软件。
内含全国主要大中城市矢量地图，无缝拼接，自动切换；超大容量MMC卡或SD卡，可存储大量的航点、航线、面积、航迹等导航信息；集多种数据采集方式和导航模式于一身；可自定义的数据属性可应用于各行各业；更简单、更人性化的界面使得操作简单，使用更方便，是众多同类产品中的佼佼者。
本手册共分3大部分，第一部分讲述软件的启动，菜单，窗口，热键以及系统的设置等等(第一章,第二章)；第二部分讲述如何使用GPS测绘软件软件(第三章)；第三部分讲述GPS测绘软件的数据接口(第四章)；目录第一章 GPS测绘的界面环境1.1 如何启动GPS测绘软件 (4)1.2 界面环境 (5)1.3 信息窗口 (5)1.3.1卫星星历 (5)1.3.2 导航罗盘 (6)1.3.3 旅行计算机 (6)1.4 使用快捷键 (7)第二章软件的配置2.1 设置航迹的存储方式 (8)2.2 设置系统参数 (9)2.3 设置图层 (9)2.4 设置坐标转换参数 (10)2.5 自定义属性 (10)第三章导航定位3.1 数据采集 (11)3.1.1 采集点 (11)3.1.2 采集线 (12)3.1.3 采集面 (13)3.1.4 采集轨迹 (13)3.2 定位 (13)3.2.1 地图浏览 (13)3.2.2 地图分级显示和切换 (14)3.3 导航 (15)3.3.1 导航模式 (15)3.3.2 测量 (15)3.3.3 分类查询 (16)3.3.4 使用管理器 (16)3.3.4.1航点表 (17)3.3.4.2兴趣点表 (17)3.3.4.3航线表 (18)3.3.4.4航迹表 (18)3.3.4.5区域表 (19)3.4 通信 (19)3.4.1 通信概述 (19)3.4.2 设置终端ID (19)3.4.3 呼叫 (20)3.4.4 发送短消息 (21)第四章 GPS测绘数据下载软件4.1 关于DataLog (21)4.2 安装DataLog (21)4.3 DataLog的界面环境 (21)4.4 如何下载数据 (22)4.5 编辑下载的数据 (23)4.6 如何将数据上传给GPS测绘 (23)4.7 数据交换 (24)编后语 (25)第一章 GPS测绘的界面环境1.1 如何启动GPS测绘软件GPS测绘软件是运行于Mio P360掌上电脑上的WINCE应用程序，安装在MMC卡或者SD卡的GpsNav文件夹中。
GPS车辆追踪器用户手册说明书
GPS Vehicle tracker(GPS+GSM+SMS/GPRS)User Manual(Version 5.0N)This user manual has been specially designed to guide you through the functions and features of your GPS vehicle tracker.1. Accessories:▶Device▶Power cord▶Relay▶Microphone▶SOS alarm cable & button▶User Manual2. SpecificationsDimension 106(L) x 54(W) x 16(H) mm Weight 96gBackup Battery 450mAh / 3.7VOperation Temperature-25℃-60℃Humidity 5% - 95%Standby Time 60hoursGSM Frequencies 850/900/1800/1900 MHz GPRS Class 12GPS Channel 20GPS Sensitivity -159dBmAcquisition Sensitivity -144dBmPosition Accuracy 10mTTFF （Open Sky）Cold Start: ＜38s Warm Start：＜15s Hot Start：＜2sGSM/GPS Antenna Built-in designLED Indicator GSM-green, GPS-blue, Power-redData Transmit TCP, SMSGeo-fence View any existing Geo-fence in the mapSpeeding Alarm Report when speeds higher than the pre-set value. Low Power Alarm Alarm when backup battery is running outNon-movement Detection Movement alarm based on built-in 3D motion sensor Mileage Report Track by time/distance intervalRemote Control Cut off petrol/electricity3. LED IndicationsGPS LED Indicator - BlueFlashing (interval 0.1s) Searching GPS signalSolid blue GPS fixOFF No GPS fix or initializingGSM LED Indicator - GreenQuick flashing (interval 0.1s) GSM initializingSlow flashing (flash 0.1s every 2s) Receive GSM signal normally Solid green Connected to GSM network OFF No GSM signalPower Status - RedFlashing (interval 0.1s) Low batterySlow flashing (interval 0.2s) Full chargeSlow flashing (flash 0.1s every 2s) Normal operatingSolid Red ChargingOFF Low battery/Power offIgnition detection indication: three LED indicators take turns flashing.4. Getting StartedPlease follow below instructions for ensuring safe and correct use.4.1 Install the SIM cardPlace the SIM card into the device with the gold-colored side facing down.Note: Make sure there is enough credit on the SIM card. If you will be using the GPRS function, you should pay attention to the current SIM card GPRS charge.4.2 Install the deviceYou need to choose somewhere that it won't be found, because the whole point of fitting covert GPS vehicle tracker is the secrecy element.Installation please refers to below picture.NOTE:1. Any high power devices such as reversing radar, anti-theft device or communication equipment would affect the signal of the device.2. All metallic cases of the windshield will attenuate the signal on the tracking device. It’s simply due to the shielding effects of the metal compound of the case.4.3 Wiring configurationLine No. Specification Color Instruction1. 2 Keypod Orange / Orange Connect to SOS button3. 4 MIC-,MIC+ Black / Red Connect to Microphone5 TX Green Sending data (TX) / backup6 RX White Receiving data (RX) / backup7 GND Black Ground wire8 MOTOR Yellow Connect to relay control line9 ACC White Connect to ACC ignition10 V- Black(thick) Negative side of 12V/24Vcar storage battery.11 V+ Red(thick)Notes of the relay wiringThe relay wiring of pump: oil connectors of both ends are a fine white line (85) and a fine yellow line (86). The fine white line (85) is connected to vehicle positive power (+12V). The fine yellow line is connected to the device relay control line.Cut off the positive connection line of the pump; then connect in series to the relay N.C. contact (thick green line 87a) and the other end to relay COM contact (thick green line 30).4.4 Device wiring diagramPlease choose the right relay (12V-standard / 24V-optional) for the proper installation. 4.5 Power/ACC/Tele-cutoff(petrol/electricity) control line (4 pin) 1. Your device comes with a power cord and is designed to use only manufacturer-specified original device. The red line is positive while the black one is negative (the side should not be connect with ground wire).2. The ACC line (white) connects to ACC switch of the vehicle. Please be sure to connect the ACC line; otherwise the device will enter ignition detectionstatus when disconnect the ACC line. If you don’t need to anti-theft temporarily, just connect the ACC line to the positive side in parallel.3. Tele-cutoff (petrol/ electricity) control line (yellow) is connected to pin 86 of the Tele-cutoff (petrol/ electricity) relay (equal to the yellow line of the relay socket).4. USB cable (3 pin)Firmware updating interface/expanded function to reserve space.5. MIC line (2 pin)Externally connect to microphone for voice monitoring function.6. SOS line (2 pin)Externally connect to SOS switch for SOS function.5. Quick Operation InstructionsOperation Tips: To properly use the device, common parameters should be set before initial use. This can be done by using the parameter editor or by sending SMS commands to the device. (“,”should be English comma and no space before and after the comma)5.1 APN settingTo connect default platform , please send the SMS command below:APN command format: APN,APN's Name#E.g: APN,internet# (“internet” is the APN of carrier)The device will reply “OK” if setting successfully.Note: The APN of some countries have user name and password, you may need to send SMS command as following:APN,APN name,user name,password#E.g: APN,internet,CLIENTE,AMENA#5.2 DNS settingTo connect other platform, please send the two SMS commands bleow: Command format：SERVER,1,DNS,Port,0#E.g:SERVER, 1,,8841,0#It will reply “OK” after set successfully.5.3 ON /OFF GPRSWhen you want to disable GPRS, you can SMS command to the SIM card number which used in the device.Command format:GPRS ON：GPRSON,1#GPRS OFF：GPRSON,0#It will reply “OK” after set successfully.5.4 Add specific numberSMS command to the device to set the SOS number.SOS,A,No.1,No.2,No.3#“A” means to add new numbers, for example:SOS,A,135****5991,135****5992,135****5993#If there is only one SOS number, you can appoint a specific number as SOS number. And the null means no adding.For example:SOS,A,135****5991#means to set the first number as SOS number SOS,A,,135****5992#means to set the second number as SOS number SOS,A,,,135****5993#means to set the third number as SOS numberIf set successfully, there is a “success” reply SMS.5.5 Delete specific numberBefore deleting specific number, please check its corresponding code. For the code, please SMS “PARAM#” to the device.SMS command to the device to delete the number.SOS,D,serial NO.1,serial NO.2,serial NO.3#“D” means to delete the number, for example:SOS,D,1# means to delete the first numberSOS,D,3# means to delete the third numberIf you want to delete more than one numbers, you can send this command: SOS,D,1,3# means to delete the first and third numbers.If you forget serial number of the mobile number you want delete, you can send this command:SOS,D,mobile number# means to delete the mobile number directly.For example:SOS,D,135****2360#meanstodeletethe135********directly.After deleting the SOS number, it will receive “Delete number 135XXXXXXXX success! specific number total 2” for successful deleting of the specific number.5.6 Set the center numberIf you want to cut off/restore oil by SMS command, you have to set a centernumber firstly. Only the center number can send the cut off/restore oil command to the device. You can set your own mobile number as center number.The command for setting center number is:CENTER,A,mobile number#Forexample:CENTER,A,159****3401#If set successfully, there is an “OK” reply message.NOTE：Only the SOS number can be used to set center number successfully.5.7 Delete the center numberSMS command to the device to delete the center number.The command is:CENTER,D#For example:CENTER,D#If set successfully, there is an “OK” reply SMS.NOTE：Only the SOS number can be used to delete center number successfully.Only SOS phone number can send this command successfully to set the center number. There is only one center number can be set.5.8 Check parameter settingSend command to the terminal, you can check the parameter setting. Command format: PARAM#e.g.: PARAM# Information replied:IMEI: 353419032348877 ---IMEI number of the device;Timer: 10,10; ---GPS data uploading Interval;SENDS:5; --- the GPS working time when ACC is OFF;SOS:159****3401;---SOSnumbers,maximum3SOSnumberscanbeset and used for alarm and monitoring;CenterNumber:159****3401;---only1centernumbercanbesetandused for cutting off /restoring oil command;Sensorset:10,1,5,180 --- detect 5 vibrations in 10s; the alarm delay is 180s; Defense time: 10; --- the defense delay is 10 minute;TimeZone:E,8,0; --- set time zone; default as E8.The replied information contains IMEI number, GPS data uploading interval, SENDS, SOS, center number, sensor set time interval, defense time and time zone.5.9 Check GPRS parametersSMS command format：GPRSSET#Eg：GPRSSET#Reply message：GPRS:ON //GPRS on/off status// Currently use APN:,,; //APN setting information// Server:1,,8841,0; //platform information// URL:/maps?q=; //preset web link setting information // 5.10 GPS data uploading intervalThe default sending interval is 10,10. It means when ACC ON ,the device will upload positioning data to platform server every 10s.when ACC OFF ,the device will upload positioning data to platform server every 10s.Users can modify sending interval by SMS“TIMER,time1(seconds), time2(seconds)”The time1&time2 ranges from 10-18000sFor example:TIMER,10,20#It means when ACC ON ,the device will upload positioning data to platform server every 10s.when ACC OFF ,the device will upload positioning data to platform server every 20s.5.11 Sensor alarm time settingWhen the vehicle power is off and ACC is in low-level, if ACC is off over 10 minutes, the device will enter sensor alarm state. In this case, if the vehicle vibrates for a few times, it will activate the vibration alarm system. If the vehicle battery is still not on (ACC is in low level) after 3 minutes, the device will start vibration alarm.SMS format: “DEFENSE,TIME(minutes)#” The time ranges from 1 to 60 mins.For example: DEFENSE,15#. It means when ACC is in low level for 15mins, it will enter sensor alarm status (vehicle power is off)NOTE：1. Preset SOS numbers when send SMS alarm messages and calls2. If there is no need for vibration alarm, please SMS SENSOR,0# to close it.5.12 Restore to factory settingSMS command format: “FACTORY#” to set all parameter to default factory value. Once received “OK”, it succeeds.5.13 Reboot deviceWhen there is something wrong with the link of GPRS, e.g., The parameter setting of the device is correct, but you can't track the car on the platform. At this moment you can send a command to the device to reboot the device. The format is: RESET#After receiving this command, the device will reboot after 1mins.6. Operation of device6.1 Power on/ Power offPower on: Once insert a valid SIM card and connect all the wires, turn on the device, then Power LED will flash first, During signal searching process, GSM and GPS LED will flash. Once GPS LED keeps solid light, it means the device has been located and it starts to work.Power off: Just turn off the power switch.The device will begin to upload positioning data to server once inserting a valid SIM card and power on. During the working time, it can upload data to server every 10 seconds.6.2 Check location1. Via SMS1.1 SMS “WHERE#”, to the SIM number of device. The device will send a location message automatically. You can get the coordinates. If the device does not search any information of location, it will send “No data” to the cell phone.Example:Lat:N22.571285,Lon:E113.877115,Course:42.20,Speed:0.0740,DateTime:10-11-23 22:28:511.2 SMS “URL#”, to the SIM number of device. The device will send a location Google Map link. If the device does not search any information of location, it will send “No data” to the cell phone.Example:<Date Time：10-11-23 23:42:51> /maps?q=N22.571490,E113.8771032. Via platformGo to the platform website offered by dealers to check your vehicle location.6.3 SOS alarmIn emergent case, press SOS for 3s to activate SOS alarm. Then the device will send SOS SMS to preset specific numbers and then dial the numbers in circles until the call is picked up. At the meantime, the device will upload SOS alarm data to the server. And it will send:SOS Alarm! <DateTime:11-06-17 14：53：06>，/maps?q=N22576713,E113.916585Note: The specific numbers should be preset, just refer to 6.46.4 Wire cut-off alarmWhen the electricity supply of device is cut off, it will activate cut-off alarm. In this case, the device will send related SMS to the specific numbers and dial the numbers in circles. If nobody answers, the call just keeps 3 loops at most. At the meantime, the device will upload SOS alarm data to the server. And it will send:Cut Power！<Date Time:11-06-17 14：53：06>，/maps?q=N22576713,E113.916585Note: The specific numbers should be preset, just refer to 6.46.5 Low battery alarmWhen the device is only working with battery, once the internal voltage of battery is less than 3.7V, device will send low battery alarm sms to specific number and alarm on platform.Low battery alarm sms content example: “Attentionbattery too low, please charge.” Which means the battery is to low, to inform user charging it i n time. Note: The specific numbers should be preset, just refer to 6.46.6 Vibration alarmThe vibration alarm function is off by default. To activate this function, please send the following command: SENALM, ON#. The alarm will be sent to both the service platform and SOS numbers.When vehicle power is off, ACC status is low, and if the lead time of low ACC is more than 10 minutes （settable）, device will activate security alarm. When the security alarm is on, once the vehicle vibrates for several times, the alarm will be activated; in the next 3 minutes, if vehicle power is still off（ACC status is low）, device will start alarm. At this time, it will send alarm message to the service platform with the latitude and longitude, while the platform will reply the Chinese address. Then the terminal will send vibration alarm message to SOS numbers with the Chinese address, and call the SOS numbers in cycle. If nobody answers, it will stop calling after 3 loops.If the Chinese address can not be acquired for certain reason, the terminal will send a message with the website link to the SOS numbers.e.g.:Sensor Alarm！<11-23 14:53>,/maps?q=N22576713,E113.916585Note:1.The SOS numbers should be preset.2.Send “SEN ALM, OFF#” to turn off the vibration alarm.6.7 Voice monitoringWhen the special number cell phone dial device, ringing for 10 seconds, it will enter voice monitoring status. At this time, caller can monitoring the sound in vehicle. Incoming call from non special number will not activate voice monitoring function.Note:To realize this function, please set special number beforehand.The SIM card put into the device should be equipped with caller identification.6.8 Oil cut-off1. Via platformSend oil cut-off command on platform. To make sure the security of vehicle, tracker can only indicate to cut off oil when GPS is in valid position status, and the speed is less than 20KM/H or in static. Platform account password is needed when sending oil cut off command.2. Via SMSFirstly, you should set a center number. Please refer to 6.6.Only center number can send the command to the device to cut off and restore oil.The format is: RELAY,1#After the command is carried out, it will reply “Cut off the fuel supply: Success! Speed:0 Km/h”. If the command didn't carry out, it will reply the reason about fail to carry out.Note: To ensure the safety of the driver and the car, this command is valid only under two conditions: the GPS is located; the speed is less than 20km/h 6.9 Restoring Oil1. Via platformWhen the alarm is off, sending recover oil commands manually. Device will restore oil supplying, and vehicle will work normally again.Platform account password is needed when sending oil cut off command.2. Via SMSOnly center number can send the command to the device to restore oil.The format is: RELAY,0#After the command is carried out, it will receive “Restore fuel supply:Success!”6.10 Over speed AlarmWhen the car is moving over a limited speed in average in a limited time period, then the device will send over speed alarm SMS to user.To turn on the over speed function, please send below SMS command: SPEED,ON/OFF,Time,Limited speed,uploading mode#Speed alarm switch:ON/OFF default:OFFTime range (seconds):5-600s(default as 20s)Limited speed range(km/h):1-255km/h. default:100Mode:0/1. default:1 way of alarming,0 means GPRS only,1 meansSMS+GPRSExample:SPEED,ON,20,100,1#Means when the car is moving over 100km/h in average in 20 seconds,the device will send over speed alarm to user7．Web based tracking online activationThe GPRS web based tracking platform allows real time tracking with the latest Google maps. There is also a playback feature that allows you to view where the vehicle has been for up to 30 days in the past making it ideal for fleet management.8．Trouble shootingIf you are having trouble with your device, try these troubleshooting procedures before contacting a service professional.Problems Causes SolutionsFail to connect platform The fuse blows Replace the fuse ACC ignition disconnected Turn on ACC with keyFail to connect network Wrong installation of SIMcardCheck SIM card installation(Refer to 4.1 Install SIM card) Filth on the SIM card ironsurface.Clean itUseless SIM Contact internet serviceproviderImproper installation Check installation of device(Refer to 4.2 Install the device) Beyond GSM service area Use it in effective GSM serviceoffer areaBad signal Try again in a better signalareaFail to charge The voltage is unsuitable Connect with power withsuitable voltage Improper connection Check connection withcharger1. The warranty is valid only when the warranty card is properly completed, and upon presentation of the proof of purchase consisting of original invoice indicating the date of purchase, model and serial No.of the product. Wereserve the right to refuse warranty if this information has been removed or changed after the original purchase of the product from the dealer.2. Our obligations are limited to repair of the defect or replacement the defective part or at its discretion replacement of the product itself.3. Warranty repairs must be carried out by our Authorized Service Centre. Warranty cover will be void, even if a repair has been attempted by any unauthorized service centre.4. Repair or replacement under the terms of this warranty does not provide right to extension or renewal of the warranty period.5. The warranty is not applicable to cases other than defects in material, design and workmanship.Maintenance RecordShenZhen Concox Information Technology CO.,LtdTel: +86 755 2912 1200Fax: +86 755 2912 1290E-mail:**************.Add: 4/F, Building B, Gaoxinqi Industrial Park,Liuxian 1st Road, No.67 Bao'an District, Shenzhen DateServiced by Product ModelIMEI NumberFaultDescriptionsCommentsWarranty instructions and service。
GPS定位终端说明书
GPS车辆防盗追踪器安装使用指南（版本1.3）GPS定位防盗一体替代传统防盗器手机就是你的遥控器安装使用前请仔细阅览说明书绑定激活说明（必须要做，否则无法进行其它操作）车主手机给追踪器手机号码发送激活短信：（注：发短信前先确定开机状态，并可正常接收短信）短信格式：SZMM,老密码,新密码, 定位器手机号码其中初始密码为123456，新密码由用户自己设置。
【举例】注：(隔开符号为：逗号)SZMM,123456,123456,138XXXXXXXX 其中“138XXXXXXXX”为定位器内所插卡的手机号码。
收到提示成功的短信后，车主可以进行其它短信指令操作或网上查车操作。
（需要修改密码也同上操作）设置参数：（车主手机发送短信代码给定位器手机号）车主发送“SZCS”指令，可以对车辆的相关配置信息进行修改。
指令格式如下：SZCS,密码,参数名=参数值（,参数名=参数值，……）(隔开符号为：逗号)参数名可以为下列几种：例如：开启震动短信通知：SZCS,密码,VIB =1关闭振动短信通知：SZCS,密码,VIB =0 （默认）开启震动电话通知：SZCS,密码,VIBCALL=1 （默认）关闭震动电话通知：SZCS,密码,VIBCALL=0注：短信通知每次短信费0.1元电话通知直接挂机零费用开启自动休眠：SZCS,密码,SLEEP=1关闭自动休眠：SZCS,密码,SLEEP=0 （默认）自动休眠说明：静止超过30分钟自动进入休眠省电状态，有震动立即唤醒，或者车主拨打定位器卡号即唤醒开启超速短信通知：SZCS,密码,SPEED =130（超速130公里即短信报警，数值自由设定）关闭超速短信通知：SZCS,密码,SPEED =0 （默认）关闭追踪：GBZZ 开启追踪：KQZZ定位：车主手机发送短信“DW”到追踪器电话号码上，追踪器将回复中文短信，短信中描述车辆当前所处的位置。
比如：XX 省XX市XX路XX大厦附近。
360汽车卫士(精英版)中文使用说明书V1.0
目录一、注意事项………………………………………………二、终端设备的组成………………………………………三、终端主要功能…………………………………………四、终端功能设置五、功能实现必备条件……………………………………六、终端设备的安装………………………………………七、应用范围………………………………………………八、终端设备参数…………………………………………一、注意事项：1、用户安装设备前请仔细阅读本说明书。
2、安装前请先插入UIM卡，确保UIM卡支持CDMA网络，没有欠费、开通短信、开通CDMA1X数据功能，并开通来电显示，否则设备无法正常工作。
3、请先确认所有设备和连接线连接正确后再接主机电源。
切勿在主机上电的情况下安装或拆卸。
如发现有遗漏线或误接，请先切断电源，否则容易损坏设备。
4、本设备为无线通讯设备，进入油库和危险品场所前请切断主机电源。
5、本设备工作电压为12V-24V，请在工作电压范围内使用。
6、您的GPSone车载终端的主机是一个低功率的无线发射机和接收机，它在使用中接收并发送射频信号。
7、为了避免电磁干扰或配置不兼容，请您在贴有通知的场所按规定停止使用设备。
360汽车定位防盗终端二、终端设备的组成：1．终端（如图）：2．终端指示灯：终端设备有红色指示灯。
在给设备通上电源后，终端设备的红色指示灯会亮十几秒，然后进入每两秒闪一下，表示设备进入工作状态。
三、终端主要功能：A、定位跟踪：通过互联网平台或手机W AP网站对终端设备进行实时定位，了解设备运行状态。
定位平台根据客户要求确定。
B、远程监听：通过车主绑定的手机拨打该设备号码，设备将自动接听来电，接通后即可随时随地监听终端设备周围2--4米范围内的声音。
C、手机登陆W AP网站获取车辆所在经纬度及地图位置信息：通过手机登陆指定的网址可以获取安装设备车辆所在位置的经纬度及文字描述的位置信息，并且在地图上显示所在的位置。
D、设置定位时间间隔：通过互联网或手机W AP网站对终端设备设置定位时间的间隔和定位频率。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
360gps定位器使用说明书
一、安装360gps定位器卡。
用户需要在定位器关机的状态下将卡装进去，然后开机。
二、安装360gps定位器。
根据说明书的指示将GPS定位器的线分别接上，无线GPS定位器不用接线，要找好合适的安装位置，防止温度过高或者金属物太多影响定位器的使用。
三、登录平台。
根据说明书的提示登录，输入自己的设备号与初始密码，即可进行查车。
四、溜车。
安装完毕后，将车开出去匀速溜一圈，速度不能太快。
大概二十分钟后汽车定位器的定位数据就能在平台上显示了。