18650锂电池组技术规格书
YAGEO
6
R9,R10
Resistor
SMD 5.1KΩ±5%
0603
2
YAGEO
7
R7
合金电阻
P=1W
SMD 10mΩ±5%
2512
1
YAGEO
8
R6
Resistor
SMD 51Ω±5%
0603
1
YAGEO
9
C1,C2,C3
Capacitor
SMD 0.22μF
0603
3
YAGEO
10
C5,C6
断开短路电路
内阻
RSS
主回路通态电阻
RSS≤65mΩ
消耗电流
IDD
工作时电路内部消耗
30.0μA Max
零 V 充电
OV
向0 V电池充电（电芯电压最小1.7V）
允许
4 Parts list主要元件清单
NO.
元件编号
元件名称
元件规格
封装式
数量
厂商/备注
1
U1
Batteryprotection IC
S8254AANFT-TB-G
TSSOP-16
1
SEIKO
2
Q3,Q4
Silicon MOSFET
AO4407
SO-8
2
AOS
3
R1,R2,R3
Resistor
SMD 510Ω±5%
0603
3
YAGEO
4
R4,R5,R11
Resistor
SMD 10KΩ±5%
0603
3
YAGEO
5
R8
Resistor
SMD 1MΩ±5%
0603
0.1±0.025V
VDET3
过充电流检测电压
/
IDP
过电流保护电流
8.0～11.0A
IDP
过充电流保护电流
/
tVDET3
检测延迟时间
10.0±5.0mS
保护解除条件
Cut load
断开负载
保护板最大持续电流
≤4.5A
短路保护
保护条件
外部电路短路
TSHORT
检测延迟时间
100～600uS
保护解除条件
VREL1
过充电解除电压
4.15±0.05V
最大充电电流
≤4.5A
过放保护
过放电检测电压（保护电压）
2.5±0.08V
tVDET2
过放电检测延迟时间
100±50mS
VREL2
过放电解除电压（备有休眠的IC，需
VDD-VM电压差在1.3V以上才可以恢复）
3.0±0.1V
过流保护
VDET3
过电流检测电压
12.6V→12.8V
外形尺寸
约35*185*68mm
要求电池组输出功率
25W
电池组标准充电电流
0.2-0.5C
锂电池保护功能部分
电池组具有充放电电流.电压保护电路，短路保护
二、电气特性
项目
符号
详细内容
标准
过充保护
VDET1
过充电检测电压（保护电压）
4.25±0.05V
过充电检测延迟时间
1.0±0.5S
2、将锂电池与保护板按接线图连接，当电池电压处于过充电压与过放电压之间，并对P+，B-充电1秒钟后，P+与B-的输出电压为电池电压。
3电池过充保护功能：在P+与B-之间加上充电器，对电池充电，电池电压充到过充检测电压时，保护电路动作，切断充电通路，实现过充保护。
4电池过放保护功能：在P+与B-之间接上负载让电池放电，当电池电压下降到过放电压时，保护电路动作，关断放电通路，实现过放保护。
5短路保护功能：当P+与B-短路时，保护电路会在5-50uS内迅速动作，切断通路，实现短路保护。
6过流保护功能：当V-端电压达（0.15±0.015V）时,保护电路会在5-15ms内迅速动作,切断通路，实现过流保护。
7过放保护恢复电压：在常温常压下，将电池连接到水泥电阻负载放电，当电流突然变为零时，断开负载，电池立即恢复输出，时，只需将充电电源电压调至比电池电压高0.1V即可对电池进行充电。
上海艾九能源科技有限公司
电池组技术规格书
型号：AJ-11.1V/15.6AH
生产日期：2011-11-03
一、电池主要参数：（具体可根据客户要求设计）
电池型号
全新进口索尼18650/2600MAH电芯
组合方式
三串六并
电池容量
15.6AH
电池组平均电压
11.1V
电池组输出电压范围
9V→12.6V
电池组充电电压范围
Capacitor
SMD 0.1μF
0603
2
YAGEO
11
C4
Capacitor
SMD 2.2μF
0603
1
YAGEO
12
PCB
Print Circuit Board
I-2040
52*16*1.2mm
1
九和咏
5 、线路板原理图
6、顶层线路板元件位置图
六、功能与说明
1、电池组的输出为两根线（红“+”黑“—”）。
18650单电芯2000MAH10C倍率型规格书
DOC NO.:江西力能新能源科技有限公司REV. :PAGE: 1 of 11Specification Approval Sheet (cylinder Cell) 产品规格确认书（圆柱电池）Model/型号：18650PCapacity/容量2000mAhVoltage/电压： 3.7V制定（Prepared By）审核（Checked By）批准（Approved By）DOC NO.:江西力能新能源科技有限公司REV. :PAGE: 2 of 111 .0 基本特性Basic performance2.0 外形图 figure 型号 Model18650S标称容量 NominalCapacity （0.5C A ）52000mAh 最低容量 （0.5C A ）51980mAh 额定电压 Nominal Voltage3.70V4.20 V 3.00V 充电截止电压 Max Charge Voltage放电终止电压 Discharge Cut-off Voltage 最大充电电流 Max. Charge Current 1C A5标准持续放电流Standard Discharge Current 1C A （最大10C A ） 5 5最大瞬间放电电流 Max. Discharge Curent 电池最大直径（光壳） Max. Diameter 15C A518.3mm 电池最大高度（光壳） Max. Height 电池重量 (Approx.) Weight (Approx.) 65mm 约5.2g 内阻（Max, at 1000Hz.） Cell Impedance ≤15m Ω(充电态) 2 .1 结构图 Structure充电方法 Charge 标准 Standard 快速 Quick0.2C A ×7.5hrs51 C A ×2.5hrs.5Method0 ℃～45℃充电 Charge放电 Discharge 贮存 Storageo o3 2 F ～113 F 操 作 温 度Operating - 20℃～60℃ o o -4 F ～140 F Temperature- 10℃～45℃ o o -4 F ～113 F3 .0 主要放电曲线 Mainly capability graph1 8650S-2000mAh 单体0.5C 充放放电图 18650S-2000mAh 单体电池不同倍率循环寿命充电电压放电电压4.0 电池性能 Characteristic若没有特别说明，电池在做各项试验前，均需在86KPa ～106 KPa 大气压，环境温度20℃±5℃，相对湿度为45％～ 7 5％的条件下，以0.2C A 恒流放电至终止电压2.75V ，并在收到产品两周内进行以下试验。
18650（2600mAh 3.7V）规格确认书说明书
CUSTOMER NO:Specification Approval Sheet规格确认书MODEL /型号: 18650（2600mAh 3.7V ）Prepared By/Date 编 制/日 期Checked By/Date 审 核/日 期Approved By/Date 批 准/日 期杨小莹/2012-5-16Customer Approval 客户确认Signature/签 字Date/日 期Company Name/公司名称Company Stamp/公司印章Amendment Records/修正记录Revision 版本Description/记述Prepared by编制Approved by批准Date/日期A FirstPublish 杨小莹Content/目录2. Model/型号Page 43.Cell Specification/电芯规格说明Page 4/54. Battery/Cell performance test Criteria/电池性能标准Page 6 4.1 Appearance inspection by visual/外观目测Page 6 4.2 Environmental test condition/外界环境条件Page6 4.3 Electrical characteristics/电气特性Page 6/7 4.4 Mechanical characteristics/机械特性Page 74.5 Safety performance/安全性能Page 85. Cell initial Dimensions/电芯初始尺寸Page 96. CAUTIONS IN USE(谨慎使用)Page 107. Period of Warranty/保质期Page 108. Storage of the Batteries/电池的存放Page 109. Other The Chemical Reaction/其它化学反应Page 1010. Note/注释Page 10 2. Model/型号Page 41 Scope/适用范围This specification is applies to describe the related Battery product in this Specification and the Battery/cell supplied by CTECHI only.本说明书只适用于描述本规格书中相关的产品。
NCR18650B规格书
ContentsPage1RecordPublication1.2. Safety Instructions 2-53. Extent of the Application 64. Battery Classification and Type 6NominalSpecifications 65.6. Electrical Characteristics 7-88andDimensions7.Design8Appearance8.8ChargeShipping9.10. Precautions on Designing of Note PC, 9-10the Charger and the Battery Pack11ConditionsStoring11.12. Handing Precautions for Lithium Ion Cells 11WarrantyExemptions 12 13.OtherRemarks 1214.15. Standard Charging Method 1213Period16.WarrantyBattery17. Battery Safety Requirements 132. Safety InstructionsProhibited ActionsThe cell contains flammable objects such as organic solvents. If the battery is mishandled, it may cause fire, smoke or an explosion and the battery’s functionality will be seriously damaged. Please read and check the following prohibited actions. Also, please equip a protection in the application so the application troubles don’t affect the battery. Additionally, SANYO highly recommends embedding these instructions into the owner’s manual.！Ｄａｎｇｅｒz Immersion"Do not immerse the battery with liquid such as water, sea water or soda."If the protection circuit in the battery is broken with liquid, the battery cannot be protected and may on fire, smoke, explode, or cause heat generation. by unexpected electrical load.z High Temperature"Do not use or place the battery near fire, a heater or a high temperatures (more than 80℃)."The battery’s polyolefin separator may get damaged from the heat and could cause an internal short circuit. This may cause the battery to catch on fire, smoke, explode, or cause heat generation.z Charger and Charge Condition"Do not use unauthorized chargers."If the battery is charged under unacceptable conditions (For example: usage in restricted temperature ranges, over voltage, or over current with unauthorized chargers) the battery may catch on fire, smoke, explode, or cause heat generation.z Reverse Polarity"Do not force a reverse-charge or a reverse-connection."The battery has correct polarity. If the battery doesn’t fit, please check the battery’s orientation and do not force into the battery mount. If the battery is forced to set with a different polarity, the battery may catch on fire, smoke, explode, or cause heat generation.z Direct Connection"Do not connect the battery with AC plug (outlet) or car plugs."The battery requires a specific charger. If the battery connects with the outlet directly, the battery may catch on fire, smoke, explode, or cause heat generation.Energy Company, SANYO Electric Co., Ltd.z Inappropriate Use with Other Equipment"Do not adapt the battery to unspecified applications. "If the battery is used for unspecified applications or systems, the battery may get damaged or catch on fire, smoke, explode, or cause heat generation.z Incineration and Heat"Please keep the battery away from heat and fire"The battery materials will get damaged and may catch on fire, smoke, explode, or cause heat generation.z Short-Circuit"Do not make a short-circuit."Do not connect the + and - terminals with conductive material. Do not carry or store the battery with metal objects (such as wire, necklace or hairpins). If the battery is in a short-circuit, excessive large current will flow and may catch on fire, smoke, explode, or cause heat generation.z Impact" Avoid unnecessary impact to the battery"Unnecessary impact may cause the battery to leak, heat generation, smoke, fire or explode. Also, the protection circuit may break and that will lose the function of the battery’s protection system.z Penetration" Do not penetrate with a nail or strike with a hammer"The battery cell may get destroyed or damaged. And the battery’s protection circuit may get damaged and case an internal short-circuit. Additionally, the battery may catch on fire, smoke, explode, or cause heat generation.z Soldering"Do not directly solder the battery"The insulator could melt or the gas release vent might get damaged from the heat.Additionally, the battery may catch on fire, smoke, explode, or cause heat generation.z Disassemble and Reconstruction"Do not disassemble the battery"If the protection circuit gets damaged, the battery will not be protected. Then, the battery may catch on fire, smoke, explode, or cause heat generation.z Charge near High Temperatures"Do not charge the battery near high temperatures"If the battery is charged near high temperatures, the battery may not be able to charge due to the activation of the protection circuit. In these conditions, the protection circuit may break and the battery may catch on fire, smoke, explode, or cause heat generation.Energy Company, SANYO Electric Co., Ltd.！Ｗａｒｎｉｎｇz Ingestion"Keep away from infants"The battery should be kept away from infants. In case of swallowing the battery, see a doctor immediately.z Storing"Do not put the battery in the microwave or other cooking appliances"The battery may on fire, smoke, explode, or cause heat generation due to heat or the electrical impact from the microwave.z Mixed Use"Do not mix the battery with other batteries."The battery should not be used with other batteries with different capacity, chemistry or manufacturer. Do not connect with other batteries or mix with other batteries. The battery may catch on fire, smoke, explode, or cause heat generation.z Rust, Changing Color and Deformities"Do not use abnormal batteries."Please stop using the battery if there are noticeable abnormalities such as abnormal smell, heat, deformities, or discoloration. The battery may have a defect and may catch fire, smoke, heat generation or explode if used continuously.z Charging Time" Stop charging if the charging process cannot be finished."If the battery can not finish the charging process within the specified time, please stop the charging process. The battery may catch on fire, smoke, explode, or cause heat generation.z Leakage①"Do not use a leaking battery near flames"If the battery or liquid leaking from the battery has a pungent odor, the battery should keep away from flames. The battery may ignite and explode.z Leakage②"Do not touch a leaking battery"If the liquid leaking from the battery gets into eyes, it will cause significant damage. If the leaking liquid gets into your eyes, please flush eyes immediately with pure water. Please consult a physician immediately. If the liquid remains in the eyes it will cause significant damage.z Transport" Pack the battery tightly during transport"To prevent short-circuit or damages, please tightly pack the battery into a case or a carton box.Energy Company, SANYO Electric Co., Ltd.！Ｃａｕｔｉｏｎz Use under Direct SunlightDo not use or leave the battery in excessive heat such as in a car in direct sunlight.The battery may catch on fire, smoke, explode, or cause heat generation. Also, it might cause a deterioration of battery's characteristics and battery life.z Static ElectricityThe battery pack has a protection circuit. Do not use the battery where it generates static electricity (more than 100V) that might damage the protection circuit. If the protection circuit is broken, the battery may catch on fire, smoke, explode, or cause heat generation. z Charging Temperature RangeCharging temperature range is regulated between 0℃ and 40℃. Do not charge the battery out of the specified temperature range. Otherwise, it may cause heat generation, leakage or a serious damage. Also, it might cause deterioration of the battery's characteristics and battery life.z ManualPlease read the manual before usage. Please save the manual for future reference.z Charging MethodPlease read the charger’s manual for the charging method.z First Time UsePlease contact the supplier If the battery has unusual odor, heat generation or rusts during the first usage.z Use by ChildrenParents must explain how to use the system and the battery. Please check back periodically to ensure children are using the system and the battery correctly.z Inflammable MaterialsPlease keep away from flammable materials during the charge and the discharge. It may catch on fire, smoke, explode, or cause heat generation.z LeakageIf electrolyte leak from the battery and adhere to the skin or clothes, immediately flush it with water. Otherwise, it may cause skin irritation.z InsulationIf lead wires or metal objects come out from the battery, please seal and insulate them completely. Otherwise, the battery may cause a short circuit and catch on fire, smoke, explode, or cause heat generation.z RecyclePlease recycle the battery according to local rules or regulations after use.Energy Company, SANYO Electric Co., Ltd.3. Extent of the ApplicationThis specification is applied to SANYO Lithium Ion Battery ofNCR18650B-H00HA for Notebook Type Personal Computer withShenzhen Syren Energy Co., Ltd.For special applications in which quality and reliability are required, or if the failure or malfunction ofthe products may directly jeopardize life or cause threat of personal injury such as for weapon,aircraft and aerospace equipment, aircraft electronics equipment, medical equipment (a part of class2 equipment, class3 or more equipment), or cause large-scale system troubles, explosion-proofequipment, electric vehicle, hybrid electric vehicle, and electric motor cycle (except electricpower-assisted bicycle), this specification shall not be applied.4. Battery Classification and Type4.1 Battery Classification SANYO Lithium Ion Battery4.2 Battery Type NCR18650B-H00HA(This model is controlled by Wassenaar Arrangement.)5. Nominal SpecificationsNotes Items Specifications5.1 Rated Capacity (Minimum) 3200mAh 0.65A discharge at 20℃5.2 Nominal Capacity (Minimum) 3250mAh 0.65A discharge at 25℃5.3 Nominal Capacity (Typical) 3350mAh Reference only5.4 Nominal Voltage 3.6V 0.65A discharge5.5 Discharging End Voltage 2.5V5.6 Charging Current (Std.) 1.62A5.7 Charging Voltage 4.20 ± 0.03V5.8 Charging Time (Std.) 4.0 hours5.9 Continuous Discharging Current (Max.)※1 4.87A 0 ~ +40℃5.10 Internal Resistance less than 100mΩAC Impedance 1 kHz5.11Weight less than 48.5gCharge 0 ~ +40℃5.12 Operating TemperatureDischarge -20 ~ +60℃5.13 less than 1 month-20 ~ +50℃Percentage ofStoring Conditions less than 3 months-20 ~ + 45℃recoverable capacityless than 1 year -20 ~ + 20℃80%※2※1 The maximum discharge current for a single cell use. However after the battery pack assembly , there will be a limitation of maximum discharge current due to a protection circuit or a protectiondevice.※2 Percentage of recoverable capacity= (Discharging time after storage / Initial discharging time) ×100The discharging time is measured by the discharge current of 0.65A until 2.5V of end voltage afterthe battery is fully charged at 25℃.Energy Company, SANYO Electric Co., Ltd.6. Electrical CharacteristicsItems Conditions Criteria 6.1 Full Charge The battery is charged with 1.62A constant currentuntil the voltage reaches 4.20V. Then, the current isreduced in order to keep the constant voltage of4.20V. The total charging time is 4.0 hours at 25 ℃.①Within 1 hour, after fully charged at 25℃, the battery is discharged with 0.65A continuously until 2.5V of end voltage at 25℃. More than 300min.6.2 Capacity②Within 1 hour, after fully charged at 25℃, thebattery is discharged with 3.25A continuously until2.5V of end voltage at 25℃.More than 54min.6.3 Cycle Life The battery is repeated 300 times of Charge andDischarge cycles, (Charged by CC-CV of1.62A-4.20V for 4.0 hours, Discharged by CC of3.25A to 2.5V (E.V.)) at 25℃. After the 300 cycles,the discharge time is measured by the Item 6.2.①.More than 180min.①Within 1 hour, after fully charged at 25℃, the battery is stored at 0 ℃ for 3 hours. After that, the discharge time is measured Item 6.2.② at 0 ℃. More than 30min.6.4 TemperatureCharacteristics②Within 1 hour, after fully charged at 25℃, thebattery is stored at 60 ℃ for 3 hours. After that,the discharge time is measured Item 6.2.② at60 ℃.More than 50min.6.5 Storage at FullyCharged State After fully charged at 25℃, the battery is stored for20 days at 60 ℃. After the storage, the battery isset in 25℃ for 3 hours. Then, the discharge time ismeasured Item 6.2.②.Then, the same battery is fully charged again andchecked the second discharge time by the Item 6.2② at 25 ℃.More than 30min.More than 40min.Energy Company, SANYO Electric Co., Ltd.6.6 Storage at Full Discharged State After fully charged at 25℃, the battery isdischarged by the Item 6.2.②. Then, the battery isstored for 20days at 60 ℃. After the storage, thebattery is set in 25℃ for 3 hours. Then, thedischarge time is measured by Item 6.2.② at25℃.More than 50min.6.7 Drop After fully charged at 25℃, the cell is dropped 3times in random direction from a height of 1 monto a flat surface of concrete.No rupture, no fireSTANDARD TEST CONDITIONS:The testes shall be implemented with new batteries that were delivered within the last 7 days.The tests shall be performed at 25±2℃(The standard temperature of second grade is specified by JIS Z 8703 (Standard Test Conditions)), 65±20 % (The standard humidity of twentieth grade is specified by JIS Z 8703 (Standard Test Conditions)). The grade of voltmeter and ammeter in the tests shall be higher than Class 0.5 which is specified by JIS C 1102 (Electric Indicator).7. Design and DimensionsThe battery design is shown in the following documents or drawings.(Drawing No. NCR18650B)8. AppearanceThe battery should not have the following appearance issues at delivery:・Scratch・Rust・Discoloration・Dirt・Deformation・LeakageThe battery should be in good condition.Energy Company, SANYO Electric Co., Ltd.9. Shipping ChargeThe battery is shipped out with the approximately 40%＊ charged state.*The 40% capacity is the condition in which SANYO ships the battery but it’s not the condition when Shenzhen Syren Energy Technology Co., Ltd. receives the battery.10. Precautions for Designing of Note PCs, the Chargers and the Battery Packs10-1. Precautions for Designing of Note PC and the Charger.(1) Charge･The battery is charged by a method of constant current-constant voltage.･Regarding NCR18650B, the charging current should not exceed 2.38A /cell.・The charging voltage should not exceed 4.20V /cell.The charging voltage is required to be set to less than 4.23V/cell with considering theaccuracy of charger. Even if the charger is failed, the total safety shall be secured.･The charger shall be equipped with a pre-charge system.If battery voltage goes down to less than 2.5V/cell, the battery should be charged by pre-charge current of maximum 0.32A. Once, the battery reached more than 2.5V/cell by the pre-charging, the charger can resume the standard charging method. However, if the battery voltage never recovers more than 2.5V/cell, the charger must be stopped and turned off.・The charger shall be equipped a full charge detection.The charger shall detect the full-charged state by a timer, current detection or open circuit voltage detection. When the charger detects the full-charge, the charger shall stop charging. Do not apply the continuous charging (trickle charging) method.･The charging temperature range should be set between 0 ℃ to +40 ℃.(2) Discharge･The discharge current should not exceed 4.87A/cell.･The discharge temperature should be between -20℃ to ＋60 ℃.･The discharge end voltage should be more than 2.5V/cell.(3) Over discharge･Do not discharge the battery less than 2.0V/cell.(4) Design of Note PCs and chargers.・The cells should be kept away from heat generating electronic parts in order to avoid deterioration of battery performance.10-2. Precautions for Battery Pack Design.(1) Shape, mechanism and material of battery packs･ The battery pack should be designed so it does not connect with to unauthorized chargers.･The battery pack should be designed so it cannot connect with unauthorized equipment and/or devices.File No NCR18650-055 Energy Company, SANYO Electric Co., Ltd.Lithium-Ion Battery Business Unit Battery System Management Department・ The terminal shape should be designed to avoid short circuit issues. In addition, the battery pack should be equipped with an over current protection function in order to prevent from external short circuit issues.・ The terminal shape and structure should be designed so it does not connect in backwards.・ The battery pack should be designed to prevent static electricity, electrolyte or water ingress issues.・The battery pack should be designed so the protection circuit functions can be inspected during the assembly process.･The battery pack should be designed so electrolyte cannot reach to the protection circuit board even if electrolyte leak out of the cells.･The cells should be fixed by a tape or a glue in the case. If the battery pack is dropped, the cells should be protected against dents, deformations and other mechanical stresses.･Plastic cases should be closed with glue. If an ultra sonic welding method is applied to the case sealing, SANYO will not take any responsibilities for any defects.･The pack shall be designed so end users cannot remove or disassemble the cells.(2) Protection CircuitThe following protection circuit should be equipped in the battery pack:･Overcharge protectionWe recommend the overcharge protection works when cell voltage reaches more than4.23V. Then, the current shall be shut down.･Over discharge protectionIf cell voltage reaches approximately 2.2V, we recommend the over discharge protection will shut down the discharge current and the circuit consumption current will be set to less than 1µA.･Over current protectionIf discharge current exceeds approximately 4.87A, the over current protection will shut down the current.(3)Electric circuit･To avoid over discharge mode during long storage times, the consumption current of the battery pack’s protection circuit should be set as low as possible.(4)Cell connection･ The cells should not be connected using a soldering process. In order to avoid any damages, cells should be connected to lead plates by a spot welding method.(5)Precautions on label･The rating label should indicate required information and precautions.The precautions should be based on the information in section 2.File No NCR18650-055 Energy Company, SANYO Electric Co., Ltd.Lithium-Ion Battery Business Unit Battery System Management Department11. Storing Condition11-1 Storage Temperature and Humidity (Within 3 months)・ Cells should be stored between -20℃ to +40℃ in a low humidity condition (less than70 %RH) without any corrosive gases.･No condensation on the cell11-2 Long Duration Storage･ Cells should be stored between -20℃ to +20℃ in a low humidity condition (less than 70%RH) without any corrosive gases. We recommend the discharged state or partially charged state SANYO shipped out for the long duration storage.･No condensation on cells.12. Handling Precautions for Lithium Ion Cells・This section describes handling precautions for SANYO lithium ion cells which will be assembled as Note PC’s battery packs with Shenzhen Syren Energy Technology Co., Ltd. This battery pack consists of NCR18650B.12-1 Series Connections Precautions・ When cells are connected in series, make sure the lot number, the shipping charge date, and capacity rank match. Please do not mix cells with different lot numbers, shipping charge date, and capacity rank. Also, the voltage variability should be within 10mV.・ The lot number, the shipping charge date and the capacity rank are indicated on the shipping carton label.・ If cells are connected in series, the discharge end voltage should be set more than2.75V/cell.12-2 Inspection of the Battery Pack before ShippingAll battery packs shall be inspected for:・Voltage・Internal impedance・Function of protection circuit・Thermistor resistance・Thermal fuse12-3 Abnormal Cells･ Do not use damaged cells by dropping, and/or short circuit and cells with electrolyte smell and any other damaged cells.File No NCR18650-055 Energy Company, SANYO Electric Co., Ltd.Lithium-Ion Battery Business Unit Battery System Management Department13. Warranty Exemptions･ SANYO will not be liable for any damages that are caused by violations of the precautions in this specification.･SANYO will not be liable for any problems caused by design defects of the battery packs, Note PC and/or chargers.･ SANYO will not accept any abnormal cells that were caused due to any incorrect assembly process.14. Other Remarks･If there are problems in this specification, SANYO will take them into consideration.･SANYO can discuss specs or precautions that are not described in this specification.･Do not use the provided cells for other applications.15. Standard Charging Method(1) The standard charge condition is 1.62A/cell - 4.20V/cell (Constant current-constantvoltage).The charging process should be discontinued when either time, the, OCV or current, reach certain values.(2) In case of the over discharge state(For example: Battery voltage is less than 2V), thebattery should be charged by a pre-charge system in order to prevent FET’s heat generation in a circuit.(3) The pre-charging current should be approximately 0.32A. Once the battery voltagereaches more than 2.5V/cell with, the charger can resume the standard charging method. The pre-charging should have a cut-off timer and if the voltage doesn’t recover over 2.5V/cell in the set time, the charging should be stopped.(4) The current interrupt device (CID) may work if the battery is charged continuously afterfully-charged and/or is charged at high temperature.Please consult SANYO for charging method instructions.File No NCR18650-055 Energy Company, SANYO Electric Co., Ltd.Lithium-Ion Battery Business Unit Battery System Management Department16. Battery Warranty PeriodThe warranty period is limited to one year from date of shipment. SANYO will replace batteries if it is clear that there was a defect in SANYO’s manufacturing process and that the battery was not misused.17. Battery Safety RequirementsIn order to ensure the safety of the battery, please contact SANYO to discuss the application design from a mechanical or a electrical viewpoint. Also, if there are special conditions (For example: lager current load, a quick charge method or an unique usage pattern), please contact SANYO to check the conditions before the product specification is fixed.18File No NCR18650-055 Energy Company, SANYO Electric Co., Ltd.Lithium-Ion Battery Business Unit Battery System Management Department。
ICR18650NH锂电池电芯规格书
7.SafetyCharacteristics
Item
Test Method
Performances
Short Circuit
Over charge
Thebattery cellistobeshort-circuitedbyconnecting thepositiveand negativeterminals ofthebatterywith anexternalloadoflessthan100mΩuntilthesurface temperaturedecrease 10degree from the highest point.
Thebattery cellshallnot rupture, smoke, catch fire, vent or leak.The voltage is no less than .
Thebattery cellshallnot rupture, smoke, catch fire, vent or leak.
voltageofwhiletaperingthechargecurrenttoless than or equalto C. Charging time ishours inall.
①Within1hourafterfullycharged,dischargedat
continuouslydown to .
Page
4/11
Over discharge
Crush
Impact
Heating
Aftercompletecharge,thebattery cellwillbe discharged toend voltage.Then connectwith external loadof30Ωdischarge for 24hrs.
友创伟业 YCY Li-ion 18650 3.7V 2200mAh电池说明书
SpecificationSeries系列:圆柱锂离子电池Pack Type组合类型:电芯+保护板+引线Model No.型号:YCY Li-ion186503.7V2200mAhCapacity容量:2200mAhVersion版本:01Customer Approve客户确认Company Name客户名称Dept.部门Signature签名Date日期QA Dept品质R&D Dept研发Approved批准1.SCOPE使用范围This specification is applied to the reference battery in this specification and manufactured by Shenzhen YCY Technology Co.,Ltd本说明书适用于本书中所提及的深圳市友创伟业科技有限公司生产的锂电池。
12Max.Continuous Discharge Current最大连续放电电流 1.5CmA 13Operation Temperature Range操作温度Charge 充电:0~45℃60±25%R.H.Discharge 放电:-20~60℃14Storable Temperature Range储存温度1year 一年-20~25℃60±25%R.H.3months 三个月-20~40℃1week 一周-20~60℃15Weight 重量Approx 约:48.0gBattery pack 电池包16Dimension尺寸Height :64.9±0.2mm (Max.50.1mm )Battery CELL电芯Diameter :18.3±0.1mm (Max.18.4mm )3.Performance And Test Conditions3.1Standard Test Conditions 标准测试条件Test should be conducted with new batteries within one week after shipment from our factory and the batterys shall not be cycled more than five times before the test.Unless otherwise defined,test and measurement shall be done under temperature of 20±5℃and relative humidity of 45~85%.If it is judged that the test results are not affected by such conditions,the tests may be conducted at temperature 15~30℃and humidity 25~85%RH.测试必须使用出厂时间不超过一个星期的新电池，且未进行过五次以上的充放电循环。
横店集团东磁股份有限公司圆柱型锂离子电芯INR18650-26E规格书说明书
1、Scope适用范围This product specification has been prepared to specify t he Cylindrical Lithium-ion Cell to be supplied to the customer by HENGDIAN GROUP DMEGC MAGNETICS Co.,Ltd.本规格书适用于由横店集团东磁股份有限公司生产的圆柱型锂离子电芯。
2、Description and Model型号及说明2.1Description说明Cylindrical Lithium-ion Cell圆柱型锂离子电芯2.2Model电芯型号INR18650-26E2.3Site产地Manufactured in Zhejiang,China3、General Specification电芯特性NO.序号ITEMS项目SPECIFICATION参数3.1Nominal Capacity标称容量************3.2Minimum Capacity最小容量************3.3Nominal Voltage标称电压3.65V3.4Charging Voltage充电电压4.2V3.5Charging Method充电方式CC-CV(0.5C，4.2V，0.05C cut-off)恒流恒压充电(电芯以0.5C恒流充电至4.2V转恒压充电，截止电流0.05C)3.6Standard Charge Current标准充电电流0.5C3.7Standard Discharge Current标准放电电流1C3.8Discharge Cut-off Voltage放电终止电压2.5V3.9Max Discharge Current最大放电电流3C3.10Internal Resistance内阻＜25mΩ(ACIR)3.11Cycle Life循环性能+0.5C/-1C Cap(1000th)/Cap(Av10)≥80%3.12Operating Temperature（Cell surfacetemperature）工作温度（电芯表面温度）Charge充电时：0to50°CDischarge放电时：-20to60°C3.13Cell Weight重量＜47g3.14Cell Dimension电芯尺寸Height（高度）:64.95mm±0.20mmDiameter（直径）:18.25mm±0.20mmRefer to the following Fig.1参考附图13.15Storage Environment存储环境1year：-20~25℃≤70%RH3months：-20~45℃≤70%RH1month：-20~60℃≤70%RH4、Outline Dimensions外形尺寸See the following Fig.1单位：毫米Unit：mm 5.Prohibited area for welding at bottom底部禁止焊接区域6、Standard Test Conditions标准试验条件6.1Environmental Conditions环境条件Unless otherwise specified,all tests stated in this specification are conducted at25±2°C and humidity of65±20%.除非有特殊说明，所有测试的环境条件要求如下：温度25±2℃、湿度65±20%。
量能科技圆柱18650锂电池-2200mAh产品规格书
Specification for Li-ion Rechargeable cylindrical battery圆柱锂离子电池规格书MODEL/型号: 18650-2200mAh1.0 SPECIFICATIONS基本特性2.0 CONFIGURATION外形图DiameterHeight3.0 The definitions of some nomenclatures of this specification标准中的一些术语的定义：（1）Standard Charge: Charge with current 0.5C5A to limit charge voltage 4.2V under the condition of 25℃±5℃surrounding temperature, then change to charge with constant voltage till the current less than or equal to 0.01 C5A.标准充电：在环境温度20℃±5℃的条件下，以0.5C5A充电，当电池端电压达到充电限制电压4.2V时，改为恒压充电，直到充电电流小于或等于0.01C5A后停止充电（2）Initial State: The initial appearance, open-circuit voltage and internal resistance of battery.初始状态：电池的初始外观、开路电压、交流内阻。
（3）Final State: The final appearance, open-circuit voltage and internal resistance of battery.最终状态：电池的最终外观、开路电压、交流内阻。
（4）Residual Capacity: After a specific testing program, the first discharge capacity of battery.剩余容量：电池经过特定的检测程序后的首次放电容量。
18650（3600mah）规格书（标准书）
18650（3600mah）规格书（标准书）文件名称产品型号修改记录产品型号目录1 适用范围 (4)2 引用标准 (4)3 定义........................................ .. (4)3.1 手机用电池battery for cellular phone ..... . (4) 3.2 充电限制电压 limited charge voltage ............... .. (4)3.3 额定容量 rated capacity ........................... .. (4)3.4 标称电压 nominal voltage (4)3.5 终止电压 cut-off voltage (4)4 技术参数 (4)4.1 电芯参数表 (4)4.2 主要参数表 (5)4.3 保护板参数表 (5)5 要求 (5)5.1 测试条件 (5)5.2 测量仪表与设备要求 (6)5.3 外观 (6)5.4 充电制式 (6)5.5 20℃放电性能 (6)5.6 高温性能 (6)5.7 低温性能 (6)5.8 荷电保持能力 (6)5.9 循环寿命 (7)5.10 环境适应性 (7)5.11 安全保护性能 (7)5.12 电池完全完全充电后内阻 (8)6 运输、贮存 (8)7 安全规程及使用说明 (8)8 特殊要求 (8)9 PCB原理图，电芯基本特性及外形图 (9)10 电芯充放电曲线图11 成品电池尺寸图产品型号1 适用范围本规格书适用于可充电锂离子电池产品的定义、要求、测试方法、质量评定程序及标志、包装、运输、贮存。
用户请务必严格按照规格书中的测试或使用方法进行测试或使用，如对表中的测试项目或测试方法有异议，请与供应方协商解决2 引用标准下列标准所包含的条文，通过在本规范中引用而构成为本规范的条文。
GB/T 2828-1987 逐批检查计数抽样程序及抽样表（适用于连续批的检查）GB/T 2829-1987 周期检查计数抽样程序及抽样表（适用于生产过程稳定性的检查）GB/T 2900.11-1988 蓄电池名词术语3 定义本规范采用GB/T 2900.11 中规定的术语和下列定义。
三星18650 2200mAh规格书
SPECIFICATION OF PRODUCTfor Lithium-ion Rechargeable CellModel : ICR18650-22FMAug, 2008Samsung SDI Co., Ltd.Battery Business DivisionHistory of Revisions1. ScopeThis product specification has been prepared to specify the rechargeable lithium-ion cell ('cell') to be supplied to the customer by Samsung SDI Co., Ltd.2. Description and Model2.1 Description Cell (lithium-ion rechargeable cell)2.2 Model ICR18650-22FM3. Nominal SpecificationsNote (1): If the cell is kept as ex-factory status(50% of charge),the capacity recovery rate is more than 80%.4. Outline DimensionsSee the attachment(Fig. 1)5. AppearanceThere shall be no such defects as scratch, rust, discoloration, leakage whichmay adversely affect commercial value of the cell.6. Standard Test Conditions6.1 Environmental ConditionsUnless otherwise specified, all tests stated in this specification areconducted at temperature 25±5℃and humidity 65±20%.6.2 Measuring Equipment(1) Ammeter and VoltmeterThe ammeter and voltmeter should have an accuracy of the grade 0.5 or higher.(2) Slide caliperThe slide caliper should have 0.05 mm scale.(3) Impedance meterThe impedance meter with AC 1kHz should be used.7. Characteristics7.1 Standard ChargeThis "Standard Charge" means charging the cell with charge current1100mA and constant voltage 4.2V at 25℃for 3hours.7.2 Standard Discharge CapacityThe standard discharge capacity is the initial discharge capacity of the cell, which is measured with discharge current of 440mA with 2.75V cut-off at 25℃within 1 hour after the Standard charge.Standard Discharge Capacity ≥2150mAh7.3 Initial internal impedanceInitial internal impedance measured at AC 1kHz after Standard charge.Initial internal impedance ≤100mΩ7.4 Temperature Dependence of Discharge CapacityDischarge capacity comparison at each temperature, measured with dischargeconstant current 1100mA and 2.75V cut-off with follow temperature after the standard charging at 25℃.Note: If charge temperature and discharge temperature is not the same,the interval for temperature change is 3 hours.Percentage as an index of the Standard discharge capacity(=2150mAh) is 100%.7.5 Temperature Dependence of Charge CapacityCapacity comparison at each temperature, measured with dischargeconstant current 1000mA and 2.75V cut-off at 25℃after the Standard charge isas follow temperature.Note: If charge temperature and discharge temperature is not the same,the interval for temperature change is 3 hours.Percentage as an index of the Standard discharge capacity(=2150mAh) is 100%.7.6 Charge Rate CapabilitiesDischarge capacity is measured with constant current 440mA and 2.75V cut-offafter the cell is charged with 4.2V as follows.Note: Percentage as an index of the capacity at 25℃(=2150mAh) is 100%.7.7 Discharge Rate CapabilitiesDischarge capacity is measured with the various currents in under table and 2.75Vcut-off after the standard charge.Note: Percentage as an index of the capacity at 25℃(=2150mAh) is 100%.7.8 Cycle LifeEach cycle is an interval between the charge (charge current 1760mA) and thedischarge (discharge current 2200mA) with 2.75V cut-off. Capacityafter 299cycles and plus 1 day, measured under the same condition in 7.2Capacity ≥1500mAh7.9 Storage CharacteristicsCapacity after storage for 30days at 25℃after the Standard charged,measured with discharge current 1100mA with 2.75V cut-off at 25℃.Capacity retention(after the storage) ≥1720mAh7.10 Status of the cell as of ex-factoryThe cell should be shipped in 50% charged state.8. Mechanical Characteristics8.1 Drop TestTest method: Cell(as of shipment or full charged) drop onto the oak-board(thickness:≥30mm) from 4feet height at a random direction 6 times.Criteria: No leakage8.2 Vibration TestTest method: Cell(as of shipment) is vibrated along 2 mutuallyperpendicular axes with total excursion of 1.6mm and withfrequency cycling between 10Hz and 55Hz by 1Hz/min.Criteria: No leakage9. Safety10.1 Overcharge TestTest method: To charge the standard charged cell with 12V and 2200mA at 25℃for 2.5 hours.Criteria: No fire, and no explosion.10.2 External Short-circuit TestTest method: To short-circuit the standard charged cell by connecting positive and negative terminal by less than 50mΩwire for 3 hours.Criteria: No fire, and no explosion.10.3 Reverse Charge TestTest method: To charge reversely the standard charged cell with charge current2200mA for 2.5 hours.Criteria: No fire, and no explosion.10.4 Heating TestTest method: To heat the standard charged cell at heating rate of 5℃per minute up to 130℃and keep the cell in oven for 60 minutes.Criteria: No fire, and no explosion.10. WarrantySamsung SDI will be responsible for replacing the cell against defects or poor workmanship for 15month from the date of shipping. Any other problems caused by malfunction of the equipment or unsuitable use of the cell are not under this warranty.The warranty set forth in proper use, handling conditions described above,and excludes in the case of a defect which is not related to manufacturing of the cell.11. Others12.1 Storage for a long timeIf the cell is kept for a long time(3months or more), It is strongly recommendedthat the cell is preserved at dry and low-temperature.12.2 OtherAny matters that specifications does not have, should be conferred withbetween the both parties.12. PackagingSee Fig.2,Package DrawingFig. 1 Outline Dimensions of ICR18650-22FMUnit : mm Max. 18.4 Max. 65.0Fig 2. Package DrawingProper Use and Handling of Lithium Ion CellsSee before using lithium-ion cellSupplied bySamsung SDIEM1. GeneralThis document has been prepared to describe the appropriate cautions and prohibitions, which the customer should take or employ when the customer usesand handles the lithium ion cell to be manufactured and supplied by Samsung SDIEM in order to obtain optimum performance and safety.2. Charging2.1 Charging currentCharging current should be less than maximum charge current specified inthe product specification.2.2 Charging voltageCharging should be done by voltage less than that specified inthe product specification.2.3 Charging timeContinuous charging under appropriate voltage does not cause any loss ofcharacteristics. However, the charge timer is recommended to be installedfrom a safety consideration, which shuts off further charging at time specifiedin the product specification.2.4 Charging temperatureThe cell should be charged within a range of specified temperatures inthe product specification.2.5 Reverse chargingThe cell should be connected, confirming that its poles are correctly aligned.Inverse charging should be strictly prohibited. If the cell is connectedimproperly, it may be damaged.3. Discharging3.1 Discharging3.1.1 The cell should be discharged at less than maximum discharge currentspecified in the product specification.3.2 Discharging temperature3.2.1 The cell should be discharged within a range of temperatures specified inthe product specification.3.2.2 Otherwise, it may cause loss of characteristics.3.3 Over-discharging3.3.1 The system should be equipped with a device to prevent further dischargingexceeding discharging cut-off voltage specified in the productspecification.(over-discharging)3.3.2 Over-discharging may cause loss of performance, characteristics, ofbattery function.3.3.3 Over-discharging may occur by self-discharge if the battery is left fora very long time without any use.3.3.4 The charger should be equipped with a device to detect cell voltage and todetermine recharging procedures.4. Storage4.1 Storage conditions4.1.1 The cell should be stored within a range of temperatures specifiedin the product specification.4.1.2 Otherwise, it may cause loss of characteristics, leakage and/or rust.4.2 Long-term storage4.2.1 The cell should be used within a short period after charging becauselong-term storage may cause loss of capacity by self-discharging.4.2.2. If long-term storage is necessary, the cell should be stored at lowervoltage within a range specified in the product specification, becausestorage at higher voltage may cause loss of characteristics.5. Cycle life5.1 Cycle life performance5.1.1 The cell can be charged/discharged repeatedly up to times specified inthe produce specification with a certain level of capacity also specifiedin the product specification.5.1.2 Cycle life may be determined by conditions of charging, discharging,operating temperature and/or storage.6. Design of System6.1 Connection between the cell and the battery6.1.1 The cell should not be soldered directly with leads. Namely, the cellshould be welded with leads on its terminal and then be soldered withwire or leads to soldered lead.6.1.2 Otherwise, it may cause damage of component, such as separator andinsulator, by heat generation.6.2 Positioning the battery in the System6.2.1 The battery should be positioned as possible as far from heat sourcesand high temperature components.6.2.2 Otherwise, it may cause loss of characteristics.6.3 Mechanical shock protection of the battery6.3.1 The battery should be equipped with appropriate shock absorbers in order tominimize shock.6.3.2 Otherwise, it may cause shape distortion, leakage, heat generationand/or rupture.6.4 Short-circuit protection of the cell6.4.1 The cell is equipped with an insulating sleeve to protect short-circuit whichmay occur during transportation, battery assembly and /or systemoperation.6.4.2 If the cell sleeve is damaged by some causes such as outside impact,it may cause short-circuit with some wiring inside the battery.6.5 Connection between the battery and charger/system6.5.1 The battery should be designed to be connected only to the specifiedcharger and system.6.5.2 A reverse connection of the battery, even in the specified system,should be avoided by employing special battery design such asa special terminals.7. Battery Pack Assembly7.1 Prohibition of usage of damaged cell7.1.1 The cell should be inspected visually before battery assembly.7.1.2 The cell should not be used if sleeve-damage, can-distortion and/orelectrolyte-smell is detected.7.2 Transportation7.2.1 If the cell is necessary to transport to order place, such as thebattery manufacturer, careful precautions should be taken to avoiddamage of cell.8. Others8.1 Disassembly8.1.1 The cell should not be dismantled from the battery pack.8.1.2 Internal short-circuit caused by disassembly may lead to heat generationand/or venting.8.1.3 When the electrolyte is coming in contact with the skin or eyes,wash immediately with fresh water and seek medical advice.8.2 Short-circuiting8.2.1 Short-circuit results in very high current which leads to heat generation.8.2.2 An appropriate circuitry should be employed to protect accidentalshort-circuiting.8.3 Incineration8.3.1 Incinerating and disposing of the cell in fire are strictly prohibited,because it may cause rupture.8.4 Immersion8.4.1 Soaking the cell in water is strictly prohibited, because it may causemelt of components to damaged to functions.8.5 Mixing use8.5.1 Different types of cell, or same types but different manufacturer's cellmay lead to cell rupture or damage to system due to the differentcharacteristics of cell.8.6 Battery disposal8.6.1 Although the cell contains no environmentally hazardous component,such as lead or cadmium. the battery should be disposed according tothe local regulations when it is disposed.8.6.2 The cell should be disposed with a discharged state to avoid heat generationby an inadvertent short-circuit.8.7 Caution - The Battery used in this device may present a risk of fire or chemical burn ifmistreated. Do not disassemble, heat above 100℃or incinerate. Replacebattery with Samsung SDI battery only. Use of another battery may present a riskof fire or explosion. Dispose of used battery promptly. Keep away from children.Do not disassemble and do not dispose of in fire.8.8 AttachedSystem Pack Quality Guideline8-8-1 The battery pack’s consumption current.- Sleep Mode: Under 250uA.- Shut Down Mode: Under 10uA (under 2.5V).8-8-2 SOC 0%- Any bank voltage in SOC 0% of Pack should be higher than 3.0V.(Discharging Cut-off Voltage)8-8-3 Operating Charging Voltage of a cell.- Normal operating voltage of cell is 4.20V.- Max operating voltage of cell is 4.25V.8-8-4 No continuous charge- Charge cut-off condition : Cut-off Current is higher than 1/20C(Charging method: CC-CV)- Initial recharging condition : Remaining Capacity is lower than 90% or Voltageis lower than 4.10V8-8-5 Pre-charging function- Pre-charge function should be implemented to prevent abnormal high ratecharging after deep discharge.- Pre-charging condition :Operation: less than 3.0VCharging current : Under 150mA/Cell.(Continuous)Pre-charge stop (Normal Charge Start) : All cells reach 3.0V8-8-6 Cell voltage monitoring system.- The system (Charger or Pack) should equip a device to monitor each cellvoltage and to stop charging if a cell imbalance happened.8-8-7 The battery pack should have warning system for over temperature, over voltage, over current, and unexpected events would be harm to system. If battery facesharsh condition such as over temperature, Battery pack should control FET-offdirectly.8-8-8 Mechanical guides.- PCBA and Cell stack should have heat insulation material between them. (Suchas plastic barrier which is giving air isolation or non-thermal conductivematerial.)- B+ and B- wire connection should not be crossed each other. Do not make wirewhich had the voltage difference more than 4.0V get together.- The material such as double sided tape and rubber which are used in batterypack should be verified for its flammabilityHandling Precaution and Prohibitions of Lithium Ion & Lithium Ion PolymerRechargeable Cells and BatteriesInaccurate handling of lithium ion and lithium ion polymer rechargeable battery may cause leakage, heat, smoke, an explosion, or fire.This could cause deterioration of performance or failure. Please be sure to follow instructions carefully.1.1 StorageStore the battery at low temperature (below 20℃is recommended), low humidity, no dust and no corrosive gas atmosphere.1.2 Safety precaution and prohibitionsTo assure product safety, describe the following precautions in the instruction manual of theapplication.[ Danger!]■Electrical misusageUse dedicated charger.Use or charge the battery only in the dedicated application.Don't charge the battery by an electric outlet directly or a cigarette lighter charger.Don't charge the battery reversely.■Environmental misusageDon't leave the battery near the fire or a heated source.Don't throw the battery into the fire.Don't leave, charge or use the battery in a car or similar place where inside of temperature may be over 60℃.Don't immerse, throw, wet the battery in water / seawater.■othersDon't fold the battery cased with laminated film such as pouch and Polymer.Don't store the battery in a pocket or a bag together with metallic objects such as keys, necklaces, hairpins, coins, or screws.Don't short circuit (+) and (-) terminals with metallic object intentionally.Don't pierce the battery with a sharp object such as a needle, screw drivers.Don't heat partial area of the battery with heated objects such as soldering iron.Don't hit with heavy objects such as a hammer, weight.Don't step on the battery and throw or drop the battery on the hard floor to avoid mechanical hock.Don't disassemble the battery or modify the battery design including electric circuit.Don't solder on the battery directly.Don't use seriously scared or deformed battery.Don't put the battery into a microwave oven, dryer ,or high-pressure container.Don't use or assemble the battery with other makers' batteries, different types and/or models of batteries such as dry batteries, nickel-metal hydride batteries, or nickel-cadmium batteries.Don't use or assemble old and new batteries together.[ Warning! ]Stop charging the battery if charging isn't completed within the specified time.Stop using the battery if the battery becomes abnormally hot, order, discoloration, deformation, orabnormal conditions is detected during use, charge, or storage.Keep away from fire immediately when leakage or foul odors are detected. If liquid leaks onto your skin or cloths, wash well with fresh water immediately.If liquid leaking from the battery gets into your eyes, don't rub your eyes and wash them with clean water and go to see a doctor immediately.If the terminals of the battery become dirty, wipe with a dry cloth before using the battery.The battery can be used within the following temperature ranges. Don't exceed these ranges.Charge temperature ranges : 0℃~ 45℃Discharge Temperature ranges : -20℃~ 60℃Store the battery at temperature below 60℃Cover terminals with proper insulating tape before disposal.[ Caution! ]■Electrical misusageBattery must be charge with constant current-constant voltage (CC/CV).Charge current must be controlled by specified value in Cell specification.Cut-off Voltage of charging must be 4.2V.Charger must stop charging battery by detecting either charging time or cur rent specified in Cell’s specification.Discharge current must be controlled by specified value in Cell’s specification.Cut-off Voltage of discharging must be over 2.5V.■othersKeep the battery away from babies and children to avoid any accidents such as swallow.If younger children use the battery, their guardians should explain the proper handling method and precaution before using.Before using the battery, be sure to read the user's manual and precaution of it's handling.Before using charger, be sure to read the user's manual of the charger.Before installing and removing the battery from application, be sure to read user's manual of the application.Replace the battery when using time of battery becomes much shorter than usual.Cover terminals with insulating tape before proper disposal.If the battery is needed to be stored for an long period, battery should be removed from the application and stored in a place where humidity and temperature are low.While the battery is charged, used and stored, keep it away from object materials with static electric chargers.Safety Handling Procedure for the Transporter■Quarantine : Packages that are crushed, punctured or torn open to reveal contents should not be transported. Such packages should be isolated until the shipper has been consulted,provided instructions and, if appropriate, arranged to have the product inspected andrepacked.■Spilled Product : In the event that damage to packaging results in the release of cells or batteries, the spilled products should be promptly collected and segregated and the shippershould be contacted for instructions.Design of positioning the battery pack in application and charger To prevent the deterioration of the battery performance caused by heat, battery shall be positioned away from the area where heat is generated in the application and the charger.Design of the Battery PackBe sure adopting proper safe device such as PTC specified type or model in Cell Specification.If you intend to adopt different safety device which is not specified in Cell Specification, please contact Samsung SDI to investigate any potential safety problem.Be sure designing 2nd protective devices such as PTC & PCM at the same time to protect Celljust in case one protective device is fault.Please contact following offices when you need any help including safety concerns.Samsung SDI Emergency Contact Information■Samsung SDI Headquarter.575 Shin-dong, Youngtong-gu, Suwon, Kyunggi-doTel:(+82)31-210-7114 Fax:(+82)31-8006-3689■Samsung SDI Chonan factory.508, Sungsung-Dong, Chonan City, Chungchongnam-Do, KoreaTel:(+82)41-560-3669 Fax:(+82)41-560-3697■Samsung SDI America office.18600 Broadwick Street Rancho Dominguez CA 90220Tel:(+1)310-900-5205 Fax:(+1)310-537-1033■Samsung SDI Taiwan office.Rm. 3010, 30F., 333, Keelung Rd. Sec. 1, Taipei, TaiwanTel:(+886)2-2728-8469 Fax:(+886)2-2728-8480。
H18650CIL-2400mAh通用规格书A02
锂离子电芯规格书SpecificationForLithium-ion Rechargeable Cell电芯型号:H18650CILCell Type:H18650CILDocument No P/PR03/PB-D-H18650CIL Revised date2015.11.13 Version A/02Pages9 Approved Checked Designed孙新科Contents目录1Preface前言2Definition定义2.1Rated capacity标称容量2.2Standard charge method标准充电方式2.3Standard discharge method标准放电方式3Cell type and dimension电芯型号及尺寸3.1Description and model电芯说明及型号3.2Cell dimension电芯尺寸4Cell characteristics电芯特性5Technical requirements技术要求5.1Cell usage conditions电芯使用环境5.2Cell testing conditions电芯实验环境5.3Requirement of the testing equipment测量仪表要求5.4Electrochemical characteristics电化学特性5.5Environmental characteristics and safety characteristics环境适应性能与安全性能6Package picture包装图片7Shipment出货8Warranty质量保证9Storage and Shipment Requirement存储及运输要求10Warning and cautions in handling the lithium-ion cell电芯使用时警告事项及注意事项11The restriction of the use of hazardous substances有害物质控制要求12Contact information联系方式13Version history修订履历1Preface前言This specification describes the type and dimension,performance,technical characteristics,warning and caution of the lithium ion rechargeable cell.The specification only applies to H18650CIL cell supplied by Shenzhen BAK Power Battery Co.,Ltd.本标准描述了圆柱型锂离子电芯的外型尺寸、特性、技术要求及注意事项。