易信L-28h使用说明书
HSX Home Server 智能热水控制系统用户手册说明书
在使用之前請詳細閱讀 「使用說明書」及「保用條款」，並妥為保存。
Please read these instructions and warranty information carefully before use and keep them handy for future reference.HSX Home Server智能熱水控制系統家用伺服器HSX使用說明書U S E R M A N U A L請即進行保用登記﹗有關保用條款細則，請看本說明書最後一頁。
Please register your warranty information now !For Warranty Terms & Conditions,please refer to the last page of these operating instructions.重要提示1.1 如何使用本使用及安裝說明書 1.2 安全指引設備簡介2.1 概覽 2.2 技術規格 2.3 尺寸 2.4 包裝內含物安裝3.1 安裝條件 3.2 安裝位置 3.3 掛牆安裝 3.4 初次使用使用方法4.1 介面及信號燈4.2 家用伺服器與現有網路的連接 4.2.1 通過無線網路連接家用伺服器 4.2.2 通過網路電線連接家用伺服器 4.3 軟件更新 4.3.1 APP更新4.3.2 家用伺服器的軟件更新 4.4 如何使用APP 4.5 恢復出廠設定 4.5.1 重設APP 4.5.2 重設家用伺服器 4.6 清潔與保養疑難排解及客戶服務 5.1 客服地址廢物處理6.1 環境與回收利用目錄03040405060707080811111213121819202013131413171717060917App 圖標環境與回收利用該產品是由高質的元件與材料組成的，均可回收與重複利用。
在產品上的這些標記，代表著這些電子（氣）產品必須和家庭生活垃圾分類處理。
易声无线多方通话系统用户手册
方 式 1. 固 定 至 用 户 10米 范 围 内的物体上如：
铁塔
方 式 2. 利 用 臂带夹至上 臂 ，尽 量 靠 近肩部：
方 式 3. 夹 至 腰带/安全带， 尽量靠近身体 侧面：
高空作 业平台
实际使用效果，方式1优于方式2，方式2优于方式3. 其他用户按以上步骤开机自动加入网络。 注：本产品会根据环境状态自动调整耳机音量，但由于个人听力有差异，需要 手动调节时请慢慢调节耳麦音量调节按钮E，并尽可能维持在较低的音量以保护听力 。 2、 终端连接手机
（3） A.戴上Wave蓝牙耳麦（当用户佩戴有安全 帽时，请将耳麦通过安全帽下颚带固定至脸颊更可 靠）；
B.Drive蓝牙外放耳麦可手持或通过臂带挂于 上臂部；
F 左耳 B
Be
7 / 16
（4） 如果有第2个耳麦且需要使用，按（1）～（ 3）步操作；
易声无限多方通话系统
K
（5） 轻按ESound终端K按钮约1s打开电源：— —指示灯L闪亮3次后熄灭， K持续闪亮（连接上耳麦后熄灭） （6） 约5s后耳麦中听到语音提示“欢迎使用易声 语音系统”，产品已正常工作；
● 具备录音功能，16G大容量存储空间； ●空旷无遮挡环境下，地面通话距离可达500米以上，当主机用户位于5米高度 时通话距离可达1000米； ● 蓝牙耳麦和终端有效距离为10米，因此在一些特殊场合，可将终端置于附近而不用 随身携带，既避免随身携带可能带来的不便，又可防止人体对终端的遮挡干扰，增 强了通话距离和效果； ● 多重降噪技术，最大程度的避免风声等环境噪声的干扰，同时根据环境自动调节耳 麦的音量，保证语音的清晰； ● 采用耳背式耳麦，造型纤细，材质柔软，佩戴舒适可靠，可利用安全帽下颚带将耳 麦固定至脸颊以保证作业时不会掉落，简单的转动耳塞即可适应左耳和右耳； ● 符合《微功率（短距离）无线电设备的技术要求》规定的多个频段自动跳频工作， 多套设备可同时工作互不干扰；
SM828H-C-1 GPRS 采集器使用说明书
SM828H-C-1 GPRS 采集器使用说明书嘉兴市松茂电子有限公司目录1、SM828H-C-1 GPRS采集器介绍........................................................................................................... - 3 -1.1产品简介...................................................................................................................................... - 3 -1.2产品性能...................................................................................................................................... - 3 -1.3主要参数...................................................................................................................................... - 3 -2、SM828H-C-1采集器实物图及指示灯功能 ......................................................................................... - 4 -2.1实物图.......................................................................................................................................... - 4 -2.2 SM828H-C产品选型.................................................................................................................... - 4 -2.3接线图.......................................................................................................................................... - 4 -2.4端口介绍...................................................................................................................................... - 5 -2.5指示灯说明.................................................................................................................................. - 5 -3、配置软件功能介绍及操作步骤.......................................................................................................... - 6 -3.1通讯连接...................................................................................................................................... - 6 -3.2配置以太网络参数...................................................................................................................... - 8 -3.3基本参数设置............................................................................................................................ - 11 -3.4 GPRS通讯方式.......................................................................................................................... - 12 -3.5 AD/DI/DO输入输出参数设置 .................................................................................................. - 13 -3.5.1 AD/DI通道数据显示 .................................................................................................... - 13 -3.5.2 AD/DI参数配置 ............................................................................................................ - 14 -3.5.3 OUT继电器输出参数设置 ............................................................................................ - 15 -3.5.4 RS232与RS485接口配置 ............................................................................................ - 17 -3.5.5设置GSM报警短信内容 ................................................................................................ - 18 -3.5.6 SMS报警短信设置1/2 ................................................................................................. - 19 -3.5.7温度传感器序列号 ........................................................................................................ - 20 -3.6数据记录.................................................................................................................................... - 21 -3.7 TCP网络modbus通讯测试 ...................................................................................................... - 22 -4、服务与保修........................................................................................................................................ - 23 -免责声明：在您使用本产品前，请您仔细阅读本文档。
GMV-2021B MEMS 氢气传感器使用说明书
GMV-2021B MEMS氢气传感器使用说明书版本号：1.0实施日期：2021.08.28郑州炜盛电子科技有限公司Zhengzhou Winsen Electronic Technology Co., Ltd声明本说明书版权属郑州炜盛电子科技有限公司（以下称本公司）所有，未经书面许可，本说明书任何部分不得复制、翻译、存储于数据库或检索系统内，也不得以电子、翻拍、录音等任何手段进行传播。
感谢您选择炜盛科技的产品和服务。
本说明书是您恰当使用所述产品的基础，使用前请务必仔细阅读所有内容并按照所提供的使用方法使用。
任何偏离本说明书使用或去除、拆解、更换传感器内部组件，将给您带来损失，本公司对此类损失不承担任何责任。
您所购买产品的外形、结构及尺寸以实物为准。
炜盛科技致力于通过科技创新推动产品的持续改进和提升，以此为前提，本公司保留任何产品改进升级而不预先通知的权力。
使用本说明书时，确认其版本的有效性对您至关重要。
再次感谢您对我们所提供产品的认可，炜盛科技鼓励使用者根据应用场景的进化，寻求更优化的使用方法。
请妥善保管本说明书，以便在您日后需要时能及时查阅并获得帮助。
郑州炜盛电子科技有限公司GMV-2021B 氢气传感器主要应用氢能源汽车 氢能源制备 氢能源存储 氢能源输运及使用 其他场景中的氢气检测引脚定义图1 传感器结构示意图产品描述GMV-2021B 氢气传感器是基于先进MEMS 架构的全固态MOS 原理的气体传感器。
环境中的氢气将导致MOS 电导率发生变化，变化量与氢气浓度呈指数函数关系。
Pin Connection ① R H1 ② ③ R H2 ④ ⑤ R S1 ⑥ ⑦ R S2 ⑧主要特点全固态 轻量化 低功耗 长寿命优异的抗干扰能力表1产品型号GMV-2021B产品原理MEMS-MOS 标准封装 陶瓷封装检测气体 氢气 检测浓度 0.1～1000ppm(H2)标准电路条件回路电压 V C ≤24V DC 加热电压 V H 2.5V±0.1V AC or DC负载电阻 R L 可调 标准测试条件下气敏元件特性 加热电阻 R H 80Ω±5Ω（室温）加热功耗 P H ≤50mW敏感体 电 阻 R S 1KΩ～30KΩ(in 200ppmH 2) 灵敏度 S R 0(in air)/Rs(in 200ppmH 2)≥5 浓度斜率α≤0.6(R 500ppm /R 200ppmH2)说明：上图为GMV-2021B 传感器的基本测试电路。
德西玛 DEX-M-18 电热水器 用户手册说明书
Online Warranty Registration歐盟A級能源效益認證EU ENERGY EFFICIENCY CLASS APlease read these instructions and warranty information carefullybefore use and keep them handy for future reference.U S E R M A N U A LContents請即進行保用登記﹗有關保用條款細則，請看本說明書最後一頁。
Please register your warranty information now !For Warranty Terms & Conditions,please refer to the last page of this user manual.2.Safety Instructions1.OverviewPart1-11 is intended for the specialist who is responsible for the installation of the appliance. Part2, 12 and 13 are for the end user. The provided manuals correspond to the technical specifications of the appliance.The latest version of the instructions can be found online at .NoticePlease read these instructions carefully before installing or using the appliance! Keep the instructions handy with the appliance for future use!- Do not use the appliance until it has been correctly installed and unless it is in perfect working order.- Do not remove the front cover under any circumstances before switching off the mains electrical supply to the unit.- Never make technical modifications, either to the appliance itself or the electrical leads and water pipes.- The appliance must be earthed at all times.- Pay attention to the fact that water temperatures in excess of approx. 43°C are perceivedas hot, especially by children, and may cause a feeling of burning. Please note that the fittings and taps may be very hot when the appliance has been in use for some time. - The appliance is only suitable for domestic use and similar applications inside closed rooms, and must only be used to heat incoming water from the mains supply. - The appliance must never be exposed to frost. - The values stated on the rating plate must be observed.- In case of malfunction, disconnect the fuses immediately. In case of leaks, cut off the mains water supply instantly. Repairs must only be carried out by the customer service department or an authorised professional.- This appliance can be used by children aged from 3 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.2.安全守則2.Safety Instructions• If the appliance is factory equipped with a power supply cable, it must be replaced with an original spare cable from the manufacturer in case of damaged by an authorizedtechnician in order to avoid any hazards.• In accordance with VDE 0700, a circuit breaker with a contact opening gap of at least 3 mm for each pole must be provided on the mains side of the connecting box forappliances with a fixed connection.• The wall bracket must be secured with the supplied screws and dowels. The appliance must be secured to the wall bracket. The appliance may only be operated if it has been properly mounted on the wall bracket.• The prescribed nominal pressure stated on the rating plate may not be exceeded at any time.• The required water resistance may not fall below the value stated on the rating plate at any time. To observe additionally for pressure less installation:• The water outlet behind the devices must not be blocked, an d the water flow must not be restricted.• The water outlet facilities, such as shower head, jet control and other outlet unit, must be decalcified regularly. Deposits must be removed in regular intervals.• Only the fittings recommended by the manufacturer may be used.• If the appliance is exclusively connected to a single shower, only the shower headsrecommended by the manufacturer may be used. No other fittings or appliances which decrease the water flow to the shower may be installed.注意安裝及使用本熱水器前請細閱本說明書。
RDLB-28 便携式故障录波仪 使用说明书
RDLB—28便携式故障录波仪使用说明书武汉融德电测科技有限公司简介便携式故障录波仪，是以DSP、嵌入式操作系统为核心，采用三层体系结构，实现了数据采集、处理、传输、存储功能的便携式装置。
基于DSP的先进数据处理能力，录波仪实现全数字模拟信号滤波，可以根据用户需要，灵活地采用不同的采样频率，最高为100K/S，可用于暂态电气信号的录制分析。
采用先进工控内核，结合嵌入式操作系统，高效、可靠地实现数据高级处理、传输、存储、显示功能。
录波仪提供上位机软件包，可安装于基于Windows操作系统的计算机，如笔记本电脑、工程师站、DCS主机等。
上位机通过现场总线或局域网与录波仪连接，实现远程控制、数据共享、电气试验等功能。
录波仪主要功能包括：故障录波：按用户预先定义的故障判据，录波仪实时监测被测信号，并在出现故障时，启动波形录制，同时通知上位机，录制的数据保存在永久存储器上，掉电不失。
此功能可用于电力系统或其他关键设备的运行监测，用于故障诊断、排除故障。
实时监测：录波仪接入了16路开关量、24路模拟量。
录波仪实时计算模拟量有效值，计算量值（频率、有功、无功、零序、负序等），并可实时计算谐波（同时计算3路，最高21次）、矢量图（最多4组，每组最多包括6个模拟量）。
所有以上数据，包括开关量状态、模拟量波形都可以实时显示。
有效值、开关量可以实时传输给上位机。
3天历史曲线：录波仪可以以每秒一点的频率，记录16路开关量和8个模拟量（任选、包括计算量），总计3天，循环记录，用以描述被测信号的长期趋势。
录制的数据掉电不失。
发电机总启动电气试验：录波仪可以方便实现任意二组参量的X-Y特性试验，可做曲线拟合。
也可以替代振子示波器，录制任选的模拟量有效值。
功能覆盖发电机空载试验、短路试验等，以及励磁调解器阶跃试验、灭磁试验、零起升压试验等。
录波仪进行电气试验，可提高试验效率、测量精度和数据处理能力，实现电气试验的自动化。
录波仪可用于电力系统或其他行业的关键设备的在线监测；也可作为便携式仪器，用于各种工业设备的故障的监录、分析；或利用其数据处理计算能力，作为数据源，向其他系统提供实时数据。
好易通CRM 380 錄音筆簡易操作說明说明书
CRM 380錄音筆簡易操作說明一、開機/關機⏹開機：電源開關撥至“開”的位置。
⏹待機：非錄音中狀態中→長按【】鍵約3秒→進入待機狀態。
⏹待機開機：待機狀態下→長按【】鍵約3秒→開機。
⏹關機：電源開關撥至“關”的位置。
二、播放/暫停/停止⏹播放音樂檔：主畫面→按【+】或【-】鍵選擇“音樂播放”→輕按【】鍵→再按【】鍵。
⏹播放錄音檔：主畫面→按【+】或【-】鍵選擇“錄音播放”→輕按【】鍵→再按【】鍵。
⏹暫停播放：播放中→輕按【】鍵。
⏹停止播放：播放中→輕按【停止/刪除/A-B】鍵。
三、錄音操作⏹錄音：在開機狀態下→將【錄音】鍵撥至“錄音”位置。
⏹暫停錄音：錄音中→輕按【】→再輕按【】鍵即繼續錄音。
⏹停止錄音：錄音中→將【錄音】鍵撥至“停止”位置。
在錄音前請調整好系統時間。
四、播放操作⏹選曲播放：輕按【 】或【 】鍵可依次向前或向後選擇歌曲播放。
⏹快進/快退：在播放中長按住【 】或【 】鍵，即可將當前歌曲進行快進或快退，鬆開按鍵即可在選定的位置繼續播放。
⏹音量調整：在播放中→輕按【+】或【-】調整音量大小。
⏹播放功能：在播放中→輕按【功能選單】鍵→進入(循環模式、音效模式、播放速度、退出)設定。
五、A-B複讀⏹複讀設定：播放中→長按【停止/刪除/A-B】設定A起點→再長按【停止/刪除/A-B】設定B終點→即重複播放A-B段的聲音。
⏹複讀取消：複讀播放中，長按【停止/刪除/A-B】即恢復播放。
六、刪除功能⏹刪除：播放停止狀態下→輕按【停止/刪除/A-B】→選擇“刪除”→輕按【】鍵，選擇“是”，輕按【】鍵。
⏹刪除全部：播放停止狀態下→輕按【停止/刪除/A-B】→選擇“全部刪除”→輕按【】鍵，選擇“是”，輕按【】鍵。
目錄一、注意事項 (4)二、外觀圖及各部分名稱 (5)三、基本操作說明 (6)四、錄音功能 (7)五、播放功能 (12)六、刪除 (15)七、背光時間設定 (15)八、語言選擇 (16)九、關機設定 (16)十、記憶體狀態 (16)十一、軟體版本 (16)十二、儲存設定 (16)十三、密碼設定 (17)十四、恢復原廠設定 (18)十五、版本升級 (18)十六、電腦連接 (18)十七、充電 (19)十八、疑難排解 (20)十九、規格參數 (22)一、注意事項●為了保持良好性能，請避免在下列場所放置或使用本機。
LEMWS28U80 ◇SZE0N Series 产品说明书
.
DATE
: Mar. 15, 2018 .
REV
: REV. 1.0 .
SPECIFICATIONS FOR APPROVAL
3528 B105N
MODEL NAME : LEMWS28U80◇SZE0N Series
APPROVAL REMARK APPENDIX
DESIGNED
6. Flux Characteristics and Order Code
Color CRI CCT
Cool
80
6500 (F)
Cool
80
5700 (G)
Cool
80
5000 (H)
Neutral
80
4000 (J)
Warm
80
3500 (K)
Warm
80
3000 (L)
Warm
80
2700 (M)
180
3.10
0.559
30
2.69
0.081
65(Typ.)
2.80
5000K (H)
100
2.90
150
3.03
0.182 0.290 0.454
180
3.10
0.559
30
2.69
0.081
65(Typ.)
2.80
4000K (J)
100
2.90
150
3.03
0.182 0.290 0.454
3 / 25
4. Absolute Maximum Ratings
Item
Symbol
Rating
( Ta=25℃) Unit
DigitaLinx DL-HDM88A-H2 八输入八输出 HDMI 2.0 矩阵开关说明书
11675 Ridgeline Drive Colorado Springs, CO 80918Rev 180822Phone: 719-260-0061Toll-Free: 800-530-8998Fax: 719-260-0075DL-HDM88A-H2 Quick Install GuideThis guide is for quick installation only. For complete owners manual go to or use a QR reader to access the manual via QR code below.Scan QR Code with your Smart-phone or TabletDL-HDM88A-H2 Quick Guide2The DigitaLinx DL-HDM88A-H2 is an eight input by eight output HDMI 2.0 matrix switcher with HDCP 2.2 support and capable of handling resolutions up 4K@60Hz 4:4:4 / 8 bit color with static and dynamic HDR output support for each channel. The matrix features advanced independent EDID management control for each HDMI input as well as an Easy EDID analyzer. The analog and digital audio outputs on the DL-HDM88A-H2 can be set to follow the HDMI video route or can be independently routed either by API or web control interface. Built in re-clocking circuitry ensures the switcher is backwards compatible with sources with older HDMI version chip sets.The DL-HDM88A-H2 can be controlled via front panel buttons, front panel IR, external IR, remote IR, RS232, and Ethernet. The matrix includes a simple IR remote control to allow IR switching. The matrix also features a full command set for RS232 and Ethernet control with third party control systems, plus control via web user interface.Product OverviewPackage Contents•DL-HDM88A-H2 Matrix Switcher •Quick Install Guide •(1) Matrix IR Remote •(1) IR Receiver (38KHz)•(1) AC power adapter with US, UK, EU and AU power plugs •(8) Phoenix Male Connector (3.5mm, 3 Pins)• (2) Rack mounting clips with mounting screwsDL-HDM88A-H2 Quick Guide3Front Panel View1. OUTPUT CHANNEL INDICATOR - Indicates input for output port 1-82. IR - Receives signals from IR remote3. INPUT 1-8 - Input 1-8 selection buttons4. OUTPUT 1-8 - Output 1-8 selection buttons5. CLEAR - Clear button, clears the selection operation6. TAKE - Take button, implements input selection7. STORE - Store button, stores the matrix routes to preset8. RECALL - Recall button, loads the matrix routes from preset9. POWER SWITCH - Power switch for on/off control of matrixDL-HDM88A-H2 Quick Guide4Rear Panel View1. AC - AC power cord input2. HDMI IN (1-8) - HDMI input ports for connections to HDMI video sources3. HDMI IN (1-8) - HDMI output ports for connections to displays4. IR EXT. - 3.5mm IR input port for connection to IR extension cable5. EDID - EDID switch for EDID management6. FIRMWARE - USB port firmware updates7. LAN - RJ45 port for LAN connection to network or control system for telnet control8. RS232 - DB9 port for connection to control system for serial control9. AUDIO OUT - Audio de-embedded outputs for 1-8; phoenix for analog 2 channel audio and RCA for digital S/PDIF multichannelDL-HDM88A-H2 Quick Guide5Connectivity Instructions1. Verify all components included with the switcher are present before installation.2. If the switcher is going to be permanently mounted in a rack, attach the supplied rack ears to the sides of the DL-HDM88A-H2 matrix.Note: The matrix requires one rack unit (1 RU) of space. It is recommended that you leave an empty rack space above and below the DL-HDM88A-H2 for additional cooling.3. Turn off power and disconnect the audio/video equipment by following the manufacturer’s instructions.4. Connect the source devices to the HDMI inputs using HDMI cables that are less than or equal to 1.5 meters in length for 4k/60Hz signals. For source devices that are further away, it is highly recommended to install an extender such as the Digitalinx DL-HD70, DL-HDE100 or DL-HD2100.5. Connect the display devices to HDMI outputs using HDMI cables that are less than or equal to 1.5 meters in length for 4k/60Hz signals. For display devices that are further away, it is highly recommended to install an extender such as the Digitalinx DL-HD70, DL-HDE100 or DL-HD2100.6. If IR extension is required, connect the TRS 3.5 mm plug IR RX to the matrix IR EXT port, ensuring the IR receiver eye is placed in clear view of the handset used to control.7. Insert the matrix power supply included and switch on power located on the front panel. Check that the front panel LED screen is on to indicate the matrix is ready for use.8. Power on attached audio/video devices.9. Switch between sources and displays using the matrix front panel buttons, IR remote control, serial RS232, or LAN. To set a route using the front panel of the DL-HDM88A-H2, press the desired Input button (Source) and desired Output button (Display), then press Take.DL-HDM88A-H2 Quick Guide6Cabling Wiring RequirementsEthernet ControlThe DL-HDM88A-H2 may be controlled via Ethernet through a web browser interface.The TCP/IP port requires a standard straight-through Category 5 or greater cable with the TIA/EIA-568B crimp pattern for optimal operation.The default settings for the TCP/IP port are:IP address: 192.168.0.178TIA/EIA-568BOr n e/Wh te Or n e Green/Wh te Blue Blue/Wh te Green Brown/Wh te Brown P n 1P n 2P n 3P n 4P n 5P n 6P n 7P n 8Connect the Ethernet cable between to the matrix and a router with a straight-through cable or between the matrix and a computer with a crossover cable.RS232 ControlThe RS232 connection on the matrix is female DB9. User can use a USB to UART cable or a direct serial cable for matrix control. See below for control system configuration.• 9600 baud • 8 Data Bits • 1 Stop Bit •Parity = noneDL-HDM88A-H2 Quick Guide7Technical SpecificationsInput/Output Connections HDMI InputsFour (8) HDMI Type A Receptacle HDMI OutputsFour (8) HDMI Type A Receptacle IROne (1) 3.5mm TRS TCP/IPOne (1) 8P8C Port (Shielded RJ45 Female)RS232One (1) DB9 Port Female PowerOne (1) IEC C14Audio - Eight (8) Analog L/R audio outputs, 3-Pin 3.5mm Phoenix connectors - Eight (8) Digital S/PDIF audio outputs, RCA connectorsSupported Audio, Video, and Embedded Control Video Resolutions Up to 4K@60Hz 4:4:4 8 bit Color Depth: 1080p 48bit / 4K 24bitMaximum Passive HDMI Cable Distance 1.5m for 4k60 signalsVideo Compliance HDMI 2.0b and HDCP 2.2Embedded Audio Up to PCM 8 channel, Dolby Digital TrueHD, and DTS-HD Master AudioDe-embedded Audio Analog L/R Out: PCM 2.0Digital RCA S/PDIF Out: Up to Dolby 5.1, DTS 5.1Device Control Parameters IR Carrier Frequency Range38kHz at 5 volts Ethernet100BaseT RS232 Baud Rate9600 baud Chassis and Environmental EnclosurePainted Aluminum Dimensions (H x W x D)43.5 mm x 440 mm x 300 mm (1.71 in x 17.32 in x 11.81 in) – 1 RU Shipping Weight4.22kg (9.30 lbs.)Operating Temperature0° to +45° C (+32° to +113° F) Operating Humidity10% to 90%, Non-condensing Storage Temperature-20° to +70° C ( -4° to +140° F)Storage Humidity10% to 90%, Non-condensing Power, ESD, and Regulatory Power Supply100V-240VAC / 50-60 Hz Power Consumption60W (Max.)ESD Protection8kV air, 4kV contact Product RegulatoryFCC, CE, RoHS Other Standard Warranty5 years Diagnostic IndicatorsSystem LCD Included Accessories Quick Install Guide, IR Remote, IR Receiver, Rack Mounting Ears with Screws, (1) AC power adapter with US, UK, EU and AU power plugsDistances and picture quality may be affected by cable grade, cable quality, source and destination equipment, RF and electrical interference, and cable patches.Thank you for your purchase.For Technical Support please call our tollfree number at 800-530-8998 or email us at**********************Digitalinx is a brand of:11675 Ridgeline DriveColorado Springs, Colorado80921 USAPhone: 719-260-0061Fax: 719-260-0075Toll-Free: 800-530-8998。
海尔电子科技有限公司电子水洗机用户指南说明书
of the impeller.
7. Insert the pump cover and press
down .
2
a The pump cover clicks into position.
1
8. Install the filter system.
Troubleshooting
Fault
E:32-00 will light up alternately or indicator for water supply lights up.
bile device and follow the instructions.
2. Scan the QR code with the Home Connect app.
Overview of water hardness settings
You can find an overview of the water hardness values that can be selected here. A table of country-specific units can be found in the instruction manual.
Hardness mmol/l range
Setting value
Medium Medium Medium Hard Hard Hard
Soft
0 - 1.1
H00
Soft
1.2 - 1.4 H01
1.5 - 1.8 1.9 - 2.1 2.2 - 2.9 3.0 - 3.7 3.8 - 5.4 5.5 - 8.9
residue.
2. Turn the coarse filter anticlock-