L6599-高压谐振控制器芯片-中文资料

合集下载

L6599-高压谐振控制器芯片-中文资料

L6599高压谐振控制器特征50%占空比，谐振半桥变频控制高精度振荡器高至500kHz 的工作频率序号编码器件编码封装包装L6599D SO-16N 管装 L6599DTR SO-16N 卷带 L6599NDIP16管装两级过流保护：变频和停机闭锁与PFC 控制器的接口自锁禁止输入轻载脉冲工作模式上电/断电顺序或欠压保护输入单调输出电压上升为非线性软启动整合了一个能够承受600V 以上电压的高压浮动结构和一个同步驱动式高压横向双扩散金属氧化物半导体(LDMOS)器件，节省了一个外部快速恢复自举二极管用低电压下拉方式为两个栅驱动器提供一个输出电流0.3A 和灌入电流0.8A的典型峰值电流处理能力。

DIP-16，SO-16N 两种封装特征液晶电视和等离子电视的电源台式电脑和初级服务器电信设备开关电源交直流适配器的开关电源框图目录1 驱动描述 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 引脚设置 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52.1 引脚排列 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52.2 引脚功能说明 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 典型系统框图 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 电气数据 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74.1 极限参数. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74.2 热相关数据. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85 电气参数. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 典型的电气性能. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127 应用资料. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157.1 振荡器. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .167.2 工作在空载或非常轻的负载状态. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .187.3 软启动. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .217.4 电流检测，过流保护和过载保护 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237.5 闭锁关机. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .267.6 LINE检测功能. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .277.7 自举部分 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .287.8 应用实例. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .298 封装外形尺寸 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 修订记录 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 驱动描述L6599是一个用于谐振半桥拓扑电路的精确的双端控制器。

L6599中文规格 PDF

力。
n DIP-16，SO-16N 两种封装
特征
n 液晶电视和等离子电视的电源 n 台式电脑和初级服务器 n 电信设备开关电源 n 交直流适配器的开关电源
框图
1/29
PDF created with pdfFactory trial version
2/29
PDF created with pdfFactory trial version
L6599
高压谐振控制器
特征
n 50%占空比，谐振半桥变频控制 n 高精度振荡器
n 高至 500kHz 的工作频率 n 两级过流保护：变频和停机闭锁
序号编码
n 与 PFC 控制器的接口
器件编码
封装
包装
n 自锁禁止输入
L6599D
SO-16N
管装
n 轻载脉冲工作模式
L6599DTR SO-16N
卷带
n 上电/断电顺序或欠压保护输入
2.1 引脚排列 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 2.2 引脚功能说明 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3 典型系统框图 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4 电气数据 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4.1 极限参数 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 4.2 热相关数据 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 5 电气参数 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 6 典型的电气性能 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 7 应用资料 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 7.1 振荡器 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 7.2 工作在空载或非常轻的负载状态 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 7.3 软启动 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 7.4 电流检测，过流保护和过载保护 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 7.5 闭锁关机 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 7.6 LINE检测功能 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 7.7 自举部分 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 7.8 应用实例 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 8 封装外形尺寸 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 修订记录 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6599中文说明

L6599高压谐振控制器特征⏹ 50%占空比，谐振半桥变频控制 ⏹ 高精度振荡器⏹ 高至500kHz 的工作频率 ⏹ 两级过流保护：变频和停机闭锁 ⏹ 与PFC 控制器的接口 ⏹ 自锁禁止输入 ⏹ 轻载脉冲工作模式⏹ 上电/断电顺序或欠压保护输入 ⏹ 单调输出电压上升为非线性软启动⏹ 整合了一个能够承受600V 以上电压的高压浮动结构和一个同步驱动式高压横向双扩散金属氧化物半导体(LDMOS)器件，节省了一个外部快速恢复自举二极管⏹ 用低电压下拉方式为两个栅驱动器提供一个输出电流0.3A 和灌入电流0.8A的典型峰值电流处理能力。

⏹ DIP-16，SO-16N 两种封装特征⏹ 液晶电视和等离子电视的电源 ⏹ 台式电脑和初级服务器 ⏹ 电信设备开关电源 ⏹ 交直流适配器的开关电源框图目录1 驱动描述 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 引脚设置 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52.1 引脚排列 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52.2 引脚功能说明 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 典型系统框图 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 电气数据 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74.1 极限参数 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74.2 热相关数据 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85 电气参数 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 典型的电气性能 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127 应用资料 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157.1 振荡器 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .167.2 工作在空载或非常轻的负载状态 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .187.3 软启动 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .217.4 电流检测，过流保护和过载保护 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237.5 闭锁关机 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .267.6 LINE检测功能 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .277.7 自举部分 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .287.8 应用实例 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .298 封装外形尺寸 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 修订记录 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 驱动描述L6599是一个用于谐振半桥拓扑电路的精确的双端控制器。

L6599D中文资料

L6599D中⽂资料May 2006 Rev 11/36L6599High-voltage resonant controllerFeatures■50% duty cycle, variable frequency control of resonant half-bridge ■High-accuracy oscillator■Up to 500kHz operating frequency■Two-level OCP: frequency-shift and latched shutdown■Interface with PFC controller ■Latched disable input■Burst-mode operation at light load ■Input for power-ON/OFF sequencing or brownout protection■Non-linear soft-start for monotonic output voltage rise■600V-rail compatible high-side gate driver with integrated bootstrap diode and high dV/dt immunity■-300/800mA high-side and low-side gate drivers with UVLO pull-down ■DIP-16, SO-16N packagesApplications■LCD & PDP TV■Desktop PC, entry-level server ■Telecom SMPS■AC-DC adapter, open frame SMPSOrder codePart number Package Packaging L6599D SO-16N T ube L6599TR SO-16N Tape and reelL6599NDIP-16T ube/doc/128b95b11a37f111f1855bea.htmlContents L6599Contents1Device description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Pin Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42.1Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42.2Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3Typical system block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64Electrical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74.1Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74.2Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 5Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 6Typical electrical performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157.1Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167.2Operation at no load or very light load . . . . . . . . . . . . . . . . . . . . . . . . . . . 187.3Soft-start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217.4Current sense, OCP and OLP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237.5Latched shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277.6Line sensing function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277.7Bootstrap section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297.8Application example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 8Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 9Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 352/36L6599Device description3/361 Device descriptionThe L6599 is a double-ended controller specific for the resonant half-bridge topology. Itprovides 50% complementary duty cycle: the high-side switch and the low-side switch are driven ON 180° out-of-phase for exactly the same time.Output voltage regulation is obtained by modulating the operating frequency. A fixed dead-time inserted between the turn-OFF of one switch and the turn-ON of the other one guarantees soft-switching and enables high-frequency operation.To drive the high-side switch with the bootstrap approach, the IC incorporates a high-voltage floating structure able to withstand more than 600V with a synchronous-driven high-voltage DMOS that replaces the external fast-recovery bootstrap diode.The IC enables the designer to set the operating frequency range of the converter by means of an externally programmable oscillator.At start-up, to prevent uncontrolled inrush current, the switching frequency starts from a programmable maximum value and progressively decays until it reaches the steady-state value determined by the control loop. This frequency shift is non linear to minimize output voltage overshoots; its duration is programmable as well.The IC can be forced to enter a controlled burst-mode operation at light load, so as to keep converter's input consumption to a minimum.IC's functions include a not-latched active-low disable input with current hysteresis useful for power sequencing or for brownout protection, a current sense input for OCP with frequency shift and delayed shutdown with automatic restart.A higher level OCP latches off the IC if the first-level protection is not sufficient to control the primary current. Their combination offers complete protection against overload and short circuits. An additional latched disable input (DIS) allows easy implementation of OTP and/or OVP .An interface with the PFC controller is provided that enables to switch off the pre-regulator during fault conditions, such as OCP shutdown and DIS high, or during burst-mode operation.Pin Settings L65994/362 Pin Settings2.1 Connection2.2 FunctionsTable 1.Pin functionsN.NameFunction1C SSSoft start. This pin connects an external capacitor to GND and a resistor to RFmin (pin 4)that set both the maximum oscillator frequency and the time constant for the frequency shift that occurs as the chip starts up (soft-start). An internal switch discharges this capacitor every time the chip turns OFF (V CC < UVLO, LINE < 1.25V or > 6V , DIS > 1.85V , ISEN > 1.5V , DELAY > 3.5V) to make sure it will be soft-started next, and when the voltage on the current sense pin (ISEN) exceeds 0.8V , as long as it stays above 0.75V .2DELAYDelayed shutdown upon overcurrent. A capacitor and a resistor are connected from this pin to GND to set both the maximum duration of an overcurrent condition before the IC stops switching and the delay after which the IC restarts switching. Every time the voltage on the ISEN pin exceeds 0.8V the capacitor is charged by an internal 150µA current generator and is slowly discharged by the external resistor. If the voltage on the pin reaches 2V , the soft start capacitor is completely discharged so that the switching frequency is pushed to its maximum value and the 150µA is kept always on. As the voltage on the pin exceeds 3.5V the IC stops switching and the internal generator is turned OFF , so that the voltage on the pin will decay because of the external resistor. The IC will be soft-restarted as the voltage drops below 0.3V . In this way, under short circuit conditions, the converter will work intermittently with very low input average power.3CFTiming capacitor. A capacitor connected from this pin to GND is charged and discharged by internal current generators programmed by the external network connected to pin 4 (RFmin) and determines the switching frequency of the converter.L6599Pin Settings5/364RFminMinimum oscillator frequency setting. This pin provides a precise 2V reference and a resistor connected from this pin to GND defines a current that is used to set the minimum oscillator frequency. T o close the feedback loop that regulates the converter output voltage bymodulating the oscillator frequency, the phototransistor of an optocoupler will be connected to this pin through a resistor. The value of this resistor will set the maximum operatingfrequency. An R-C series connected from this pin to GND sets frequency shift at start-up to prevent excessive energy inrush (soft-start).5STBYBurst-mode operation threshold. The pin senses some voltage related to the feedbackcontrol, which is compared to an internal reference (1.25V). If the voltage on the pin is lower than the reference, the IC entersan idle state and its quiescent current is reduced. The chip restarts switching as the voltage exceeds the reference by 50mV . Soft-start is not invoked. This function realizes burst-mode operation when the load falls below a level that can be programmed by properly choosing the resistor connecting the optocoupler to pin RFmin (see block diagram). Tie the pin to RFmin if burst-mode is not used.6ISENCurrent sense input. The pin senses the primary current though a sense resistor or acapacitive divider for lossless sensing. This input is not intended for a cycle-by-cycle control; hence the voltage signal must be filtered to get average current information. As the voltage exceeds a 0.8V threshold (with 50mV hysteresis), the soft-start capacitor connected to pin 1 is internally discharged: the frequency increases hence limiting the power throughput. Under output short circuit, this normally results in a nearly constant peak primary current. This condition is allowed for a maximum time set at pin 2. If the current keeps on building up despite this frequency increase, a second comparator referenced at 1.5V latches the device off and brings its consumption almost to a “before start-up” level. The information is latched and it is necessary to recycle the supply voltage of the IC to enable it to restart: the latch is removed as the voltage on the Vcc pin goes below the UVLO threshold. Tie the pin to GND if the function is not used.7LINELine sensing input. The pin is to be connected to the high-voltage input bus with a resistor divider to perform either AC or DC (in systems with PFC) brownout protection. A voltage below 1.25V shuts down (not latched) the IC, lowers its consumption and discharges the soft-start capacitor. IC’s operation is re-enabled (soft-started) as the voltage exceeds 1.25V . The comparator is provided with current hysteresis: an internal 15µA current generator is ON as long as the voltage applied at the pin is below 1.25V and is OFF if this value is exceeded. Bypass the pin with a capacitor to GND to reduce noise pick-up. The voltage on the pin is top-limited by an internal zener. Activating the zener causes the IC to shut down (not latched). Bias the pin between 1.25 and 6V if the function is not used.8DISLatched device shutdown. Internally the pin connects a comparator that, when the voltage on the pin exceeds 1.85V , shuts the IC down and brings its consumption almost to a “before start-up” level. The information is latched and it is necessary to recycle the supply voltage of the IC to enable it to restart: the latch is removed as the voltage on the V CC pin goes below the UVLO threshold. Tie the pin to GND if the function is not used.9PFC_STOPOpen-drain ON/OFF control of PFC controller. This pin, normally open, is intended forstopping the PFC controller, for protection purpose or during burst-mode operation. It goes low when the IC is shut down by DIS > 1.85V , ISEN > 1.5V , LINE > 6V and STBY < 1.25V .The pin is pulled low also when the voltage on pin DELAY exceeds 2V and goes back open as the voltage falls below 0.3V . During UVLO, it is open. Leave the pin unconnected if not used.10GNDChip ground. Current return for both the low-side gate-drive current and the bias current of the IC. All of the ground connections of the bias components should be tied to a track going to this pin and kept separate from any pulsed current return.Table 1.Pin functionsTypical system block diagram L65996/363 Typical system block diagramTypical system block diagram11LVGLow-side gate-drive output. The driver is capable of 0.3A min. source and 0.8A min. sink peak current to drive the lower MOSFET of the half-bridge leg. The pin is actively pulled to GND during UVLO.12V CC Supply Voltage of both the signal part of the IC and the low-side gate driver. Sometimes a small bypass capacitor (0.1µF typ.) to GND might be useful to get a clean bias voltage for the signal part of the IC.13N.C.High-voltage spacer. The pin is not internally connected to isolate the high-voltage pin and ease compliance with safety regulations (creepage distance) on the PCB.14OUTHigh-side gate-drive floating ground. Current return for the high-side gate-drive current. Layout carefully the connection of this pin to avoid too large spikes below ground.15HVGHigh-side floating gate-drive output. The driver is capable of 0.3A min. source and 0.8A min. sink peak current to drive the upper MOSFET of the half-bridge leg. A resistor internally connected to pin 14 (OUT) ensures that the pin is not floating during UVLO.16VBOOTHigh-side gate-drive floating supply Voltage. The bootstrap capacitor connected between this pin and pin 14 (OUT) is fed by an internal synchronous bootstrap diode driven in-phase with the low-side gate-drive. This patented structure replaces the normally used external diode.Table 1.Pin functionsL6599Electrical data7/364 Electrical data4.1 Maximum ratingsNote:ESD immunity for pins 14, 15 and 16 is guaranteed up to 900V4.2 Thermal dataTable 2.Absolute maximum ratingsSymbol Pin ParameterValue Unit V BOOT 16 Floating supply voltage -1 to 618 V V OUT 14 Floating ground voltage -3 to V BOOT -18V dV OUT /dt 14 Floating ground max. slew rate 50V/nsV CC 12 IC Supply voltage (I CC ≤ 25 mA) Self-limited V V PFC_STOP 9 Maximum voltage (pin open) -0.3 to V CC V I PFC_STOP 9 Maximum sink current (pin low)AV LINEmax 7Maximum pin voltage (Ipin ≤ 1mA) Self-limited VI RFmin4 Maximum source current 2 mA 1 to 6, 8 Analog inputs & outputs-0.3 to 5VTable 3.Thermal dataSymbol DescriptionValue Unit R thJA Max. thermal resistance junction to ambient (DIP16)80°C/W Max. thermal resistance junction to ambient (SO16)120T STG Storage temperature range-55 to 150°C T J Junction operating temperature range-40 to 150°C P TOTRecommended max. power dissipation @T A = 70°C (DIP16) 1 WRecommended max. power dissipation @T A = 50°C (SO16)0.835 ElectricalcharacteristicsT J = 0 to 105°C, V CC = 15V, V BOOT = 15V, C HVG = C LVG = 1nF; C F = 470pF;R RFmin = 12k?; unless otherwise specified.Table 4.Electrical characteristicsSymbol Parameter TestconditionMin Typ Max Unit IC supply voltageV CC Operating range After device turn-on8.85 16 VV CC(ON)Turn-ON threshold Voltage rising10 10.7 11.4 VV CC(OFF)Turn-OFF threshold Voltagefalling 7.45 8.15 8.85 V Hys Hysteresis 2.55 VV Z V CC clamp voltage Iclamp = 10mA 16 17 17.9 V Supply currentI start-up Start-up current Before device turn-ONV CC = V CC(ON) - 0.2V200 250 µAI q Quiescent current Device ON, V STBY = 1V 1.5 2 mAI op Operating current Device ON,V STBY = V RFmin 3.5 5 mAI q Residual consumption V DIS> 1.85V or V DELAY> 3.5V or V LINE < 1.25 Vor V LINE = V clamp300 400 µAHigh-side floating gate-drive supplyI LKBOOT V BOOT pin leakagecurrentV BOOT= 580V 5 µAI LKOUT OUT pin leakage current VOUT= 562V 5 µAr DS(on)Synchronous bootstrapdiode ON-resistanceV LVG= High 150 ?Overcurrent comparatorI ISEN Input bias current V ISEN = 0 to V ISENdis-1 µAt LEB Leading edge blanking After V HVG and V LVGlow-to-high transition250 nsV ISENx Frequency shiftthreshold Voltage rising(1)0.76 0.8 0.84 VHysteresis Voltagefalling 50 mV V ISENdis Latch OFF threshold Voltage rising (1) 1.44 1.5 1.56 V td(H-L)Delay to output 300400 ns8/369/36Symbol Parameter Test condition Min Typ Max UnitLine sensing V th Threshold voltage Voltage rising or falling(1)1.2 1.25 1.3 V I Hyst Current hysteresis V CC > 5V , V LINE = 0.3V 12 15 18 µA V clamp Clamp levelI LINE = 1mA6 8 VDIS functionI DIS Input bias current V DIS = 0 to V th -1 µAV th Disable thresholdVoltage rising (1)1.77 1.85 1.93 VOscillatorDOutput duty cycleBoth HVG and LVG4850 52 %f oscOscillation frequency58.2 60 61.8kHzR RFmin = 2.7 k ?240 250 260Maximumrecommended500kHz T D Dead-time Between HVG and LVG0.20.3 0.4µs V CFp Peak value 3.9 V V CFv Valley value 0.9 VV REF Voltage reference at pin 4(1)1.92 22.08 VK M Current mirroring ratio 1A/A RF MINTiming resistor range1100k ?PFC_STOP functionI leak High level leakage currentV PFC_STOP = V CC ,V DIS = 0V 1 µAV LLow saturation levelI PFC_STOP =1mA,V DIS = 2V0.2 VSoft-start functionI leakOpen-state currentV(Css) = 2V0.5µA R Discharge resistance V ISEN > V ISENx 120Standby functionI DIS Input Bias Current V DIS = 0 to V th -1 µAV thDisable thresholdVoltage falling (1) 1.2 1.25 1.3 VHys HysteresisVoltage rising50mVTable 4.Electrical characteristics10/36Symbol Parameter Test condition Min TypMax UnitDelayed shutdown functionI leak Open-state current V(DELAY) = 0 0.5 µAI CHARGE Charge current V DELAY = 1V , V ISEN = 0.85V 100 150 200 µA Vth 1 Threshold for forcedoperation at max. frequencyVoltage rising (1)1.92 22.08 VVth 2Shutdown threshold Voltage rising (1) 3.3 3.5 3.7 V Vth 3Restart thresholdVoltage falling (1)0.25 0.3 0.35 VLow - side gate driver (voltages referred to GND)V LVGL Output low voltage I sink = 200mA 1.5 VV LVGH Output high voltage I source = 5mA12.8 13.3 V I sourcepk Peak source current -0.3 A I sinkpk Peak sink current 0.8A t f Fall time 30 ns t rRise time 60nsUVLO saturationV CC = 0 to V CC(ON),I sink = 2mA 1.1 VHigh-side gate driver (voltages referred to OUT)V HVGL Output low voltage I sink = 200 mA 1.5 V V HVGH Output high voltage I source = 5 mA12.8 13.3 V I sourcepk Peak source current -0.3 A I sinkpk Peak sink current 0.8A t f Fall time 30 ns t rRise time60 ns HVG-OUT pull-down25k ?1.Values traking each otherTable 4.Electrical characteristics11/366 Typical electrical performanceFigure 3.Device consumption vssupply voltageFigure 4.IC consumption vs junction temperatureV CC clamp voltage vs junction temperatureFigure 6.UVLO thresholds vs junction temperature12/36Figure 7.Oscillator frequency vsjunction temperature Figure 8.Dead-time vsjunction temperatureFigure 9.Oscillator frequency vstiming components Figure 10.Oscillator ramp vs junction temperature13/36Figure 11.Reference voltage vsjunction temperatureFigure 12.Current mirroring ratio vsjunction temperatureFigure 13.OCP delay source current vsjunction temperature Figure 14.OCP delay thresholds vs junction temperatureFigure 15.Standby thresholds vsjunction temperatureFigure 16.Current sense thresholds vsjunction temperatureFigure 17.Line thresholds vsjunction temperatureFigure 18.Line source current vsjunction temperatureFigure /doc/128b95b11a37f111f1855bea.html tched disable threshold vs junction temperature7 ApplicationinformationThe L6599 is an advanced double-ended controller specific for resonant half-bridge topology. In these converters the switches (MOSFETs) of the half-bridge leg are alternately switched on and OFF (180° out-of-phase) for exactly the same time. This is commonly referred to as operation at "50% duty cycle", although the real duty cycle, that is the ratio of the ON-time of either switch to the switching period, is actually less than 50%. The reason is that there is an internally fixed dead-time T D, inserted between the turn-OFF of either MOSFET and the turn-ON of the other one, where both MOSFETs are OFF. This dead- time is essential in order for the converter to work correctly: it will ensure soft-switching and enable high-frequency operation with high efficiency and low EMI emissions.To perform converter's output voltage regulation the device is able to operate in different modes (Figure20), depending on the load conditions:1.Variable frequency at heavy and medium/light load. A relaxation oscillator (see "Oscillator" section for more details) generates a symmetrical triangular waveform,which MOSFETs' switching is locked to. The frequency of this waveform is related to a current that will be modulated by the feedback circuitry. As a result, the tank circuitdriven by the half-bridge will be stimulated at a frequency dictated by the feedback loopto keep the output voltage regulated, thus exploiting its frequency-dependent transfer characteristics.2. Burst-mode control with no or very light load. When the load falls below a value, the converter will enter a controlled intermittent operation, where a series of a fewswitching cycles at a nearly fixed frequency are spaced out by long idle periods whereboth MOSFETs are in OFF-state. A further load decrease will be translated into longeridle periods and then in a reduction of the average switching frequency. When theconverter is completely unloaded, the average switching frequency can go down evento few hundred Hz, thus minimizing magnetizing current losses as well as all frequency-related losses and making it easier to comply with energy saving recommendations.Figure 20.Multi-mode operation15/3616/367.1 OscillatorThe oscillator is programmed externally by means of a capacitor (CF), connected from pin 3 (CF) to ground, that will be alternately charged and discharged by the current defined with the network connected to pin 4 (RF min ). The pin provides an accurate 2V reference with about 2mA source capability and the higher the current sourced by the pin is, the higher the oscillator frequency will be. The block diagram of Figure 21 shows a simplified internal circuit that explains the operation. The network that loads the RFmin pin generally comprises three branches:1. A resistor RF min connected between the pin and ground that determines the minimum operating frequency;2.A resistor RF max connected between the pin and the collector of the (emitter-grounded) phototransistor that transfers the feedback signal from the secondary side back to the primary side; while in operation, the phototransistor will modulate the current through this branch - hence modulating the oscillator frequency - to perform output voltage regulation; the value of RF max determines the maximum frequency the half-bridge will be operated at when the phototransistor is fully saturated;3.An R-C series circuit (C SS + R SS ) connected between the pin and ground that enables to set up a frequency shift at start-up (see Chapter 7.3: Soft-start ). Note that the contribution of this branch is zero during steady-state operation.The following approximate relationships hold for the minimum and the maximum oscillatorfrequency respectively:f min 13CF RF min------------------------------------------=f max 13CF RF min RF max ||()--------------------------------------------------------------------------=17/36After fixing CF in the hundred pF or in the nF (consistently with the maximum sourcecapability of the RF min pin and trading this off against the total consumption of the device), the value of RF min and RF max will be selected so that the oscillator frequency is able to cover the entire range needed for regulation, from the minimum value f min (at minimum input voltage and maximum load) to the maximum value f max (at maximum input voltage and minimum load):A different selection criterion will be given for RF max in case burst-mode operation at no-load will be used (see "Operation at no load or very light load" section).In Figure 22 the timing relationship between the oscillator waveform and the gate-drive signals, as well as the swinging node of the half-bridge leg (HB) is shown. Note that the low-side gate-drive is turned on while the oscillator's triangle is ramping upand the high-side gate-drive is turned on while the triangle is ramping down. In this way, at start-up, or as the IC resumes switching during burst-mode operation, the low-side MOSFET will be switched on first to charge the bootstrap capacitor. As a result, the bootstrap capacitor will always be charged and ready to supply the high-side floating driver.RF min 13CF f min-----------------------------------=RF max RF minf maxf min----------1–--------------------=7.2 Operation at no load or very light loadWhen the resonant half-bridge is lightly loaded or unloaded at all, its switching frequency willbe at its maximum value. T o keep the output voltage under control in these conditions and toavoid losing soft-switching, there must be some significant residual current flowing throughthe transformer's magnetizing inductance. This current, however, produces someassociated losses that prevent converter's no-load consumption from achieving very lowvalues.To overcome this issue, the L6599 enables the designer to make the converter operateintermittently (burst-mode operation), with a series of a few switching cycles spaced out bylong idle periods where both MOSFETs are in OFF-state, so that the average switchingfrequency can be substantially reduced. As a result, the average value of the residualmagnetizing current and the associated losses will be considerably cut down, thusfacilitating the converter to comply with energy saving recommendations.The device can be operated in burst-mode by using pin 5 (STBY): if the voltage applied tothis pin falls below 1.25V the IC will enter an idle state where both gate-drive outputs arelow, the oscillator is stopped, the soft-start capacitor C SS keeps its charge and only the 2Vreference at RF min pin stays alive to minimize IC's consumption and V CC capacitor'sdischarge. The IC will resume normal operation as the voltage on the pin exceeds 1.25V by50mV.To implement burst-mode operation the voltage applied to the STBY pin needs to be relatedto the feedback loop. Figure23 shows the simplest implementation, suitable with a narrowinput voltage range (e.g. when there is a PFC front-end).18/3619/36Essentially, RF max will define the switching frequency f max above which the L6599 will enter burst-mode operation. Once fixed f max , RF max will be found from the relationship:Note that, unlike the f max considered in the previous section ("Chapter 7.1: Oscillator "), here f max is associated to some load Pout B greater than the minimum one. Pout B will be such that the transformer's peak currents are low enough not to cause audible noise.Resonant converter's switching frequency, however, depends also on the input voltage; hence, in case there is quite a large input voltage range with the circuit of Figure 23 the value of Pout B would change considerably. In this case it is recommended to use thearrangement shown in Figure 24 where the information on the converter's input voltage is added to the voltage applied to the STBY pin. Due to the strongly non-linear relationship between switching frequency and input voltage, it is more practical to find empirically the right amount of correction R A / (R A + R B ) needed to minimize the change of Pout B . Just be careful in choosing the total value R A + R B much greater than R C to minimize the effect on the LINE pin voltage (see Chapter 7.6: Line sensing function ).Whichever circuit is in use, its operation can be described as follows. As the load falls below the value Pout B the frequency will try to exceed the maximum programmed value f max and the voltage on the STBY pin (V STBY ) will go below 1.25V . The IC will then stop with both gate-drive outputs low, so that both MOSFETs of the half-bridge leg are in OFF-state. The voltage V STBY will now increase as a result of the feedback reaction to the energy delivery stop and, as it exceeds 1.3V, the IC will restart switching. After a while, V STBY will go down again in response to the energy burst and stop the IC. In this way the converter will work in a burst-mode fashion with a nearly constant switching frequency. A further load decrease will then cause a frequency reduction, which can go down even to few hundred hertz. The timing diagram of Figure 25 illustrates this kind of operation, showing the most significant signals. A small capacitor (typically in the hundred pF) from the STBY pin to ground, placed as close to the IC as possible to reduce switching noise pick-up, will help get clean operation. To help the designer meet energy saving requirements even in power-factor-correctedsystems, where a PFC pre-regulator precedes the DC-DC converter, the device allows that the PFC pre-regulator can be turned off during burst-mode operation, hence eliminating the no-load consumption of this stage (0.5 ÷ 1W). There is no compliance issue in that because EMC regulations on low-frequency harmonic emissions refer to nominal load, no limit is envisaged when the converter operates with light or no load.To do so, the device provides pin 9 (PFC_STOP): it is an open collector output, normally open, that is asserted low when the IC is idle during burst-mode operation. This signal will be externally used for switching off the PFC controller and the pre-regulator as shown in Figure 26 When the L6599 is in UVLO the pin is kept open, to let the PFC controller start first.RF max 38--RF min f maxf min----------1–--------------------?=。

L6599应用讲解

L6599中文资料

ST公司针对日益广泛使用的LCD-TV电源推出了新一代的HB-LLC控制IC-L6599,它从L6598改进而来，从而性能更优秀，使用更便捷。

下面介绍IC特色及主要应用。

L6599是一个双端输出的控制器。

它专为谐振半桥拓朴设计，提供两个50%的互补的占空比。

高边开关和低边开关输出相位差180°,输出电压的调节用调制工作频率来得到。

两个开关的开启关断之间有一个固定的死区时间，以确保软开关及高频下可靠工作。

为使高边驱动采用高压电平位移的结构具有600V耐压，用高压MOSFET取代了外部快速二极管，IC设置的工作频率范围由外部元件调节。

起动时为防止失控的冲击电流，开关频率从设置的最大值开始逐渐衰减直到由控制环路给出的稳定状态，这个频率的移动不是线性的，用来减小输出电压的过冲，做到更好的调节。

在轻载时，IC可以强制进入到控制为猝发模式工作，用以保持空载时的最低功耗。

IC的功能包括非锁定低边禁止输入以实现OCP，具有频率移动及延迟关断，然后再自动重新起动。

更高水平的OCP在第一保护电平不足时可锁住IC以控制初级电流。

它结合了完整的应对过载及短路的保护，此外锁住禁止输入(DIS)可以很容易地改善OTP及OVP。

与PFC的接口处提供了PFC预调整器在故障时的使能端子，这些故障包括OCP，在猝发模式时令DIS为高电平。

L6599的内部方框电路如图1所示。

图1 L6599 HB-LLC控制IC的内部等效电路L6599的16PIN功能如下:1 PIN CSS 软起动。

此端接一外部电容到GND，接一电阻到RF端(4PIN)，它设置了最高振荡频率及频率移动到恒定的时间，IC加一个内部开关可以在芯片每次关闭时将此电容放电(Vcc<UVLO,LINE<1.25等)，以确保下次正常软起动。

此时，ISEN端上的电压超过0.8V，然后长期保留在0.75V以上。

8 PIN DELAY 过流的延迟关断。

从此端接一电容及电阻到GND，设置IC关断前的过流最大时间以及IC重起动之后的延迟，每个时段ISEN端电压超过0.8V时,电容就由内部150ua 电流源发生器来缓慢放电。

L6599中文资料

L6599中文资料1，Css软启动：连接一个外部电容到地，和一个电阻到RFmin到第4脚，用以设置最大振荡频率和为频率切换设定时间常数，以及芯片启动（软启动）。

当V cc<UVLO，Line<1.25V or >6V，DIS>1.85V，Isen>1.5V，Delay>3.5V时，一个内部开关会给这个电容放电，使芯片关闭，为下一个软启动作准备。

2，Delay延时：过电流延时关机，一个电容和一个电阻接在1脚与地之间，设置过流条件下的最大持续时间（从IC开始延时到IC关断），每当Isen脚上的电压超过0.8V时，其电容会由内部电流发生器充电（150uA），并由外部电阻缓慢放电，如果此电压超过2V，软启动电容就完全地放电，所以开关频率会推高到最高大值，150uA电流一直连续。

如果此电压超过3.5V，IC会关断，其内部电流发生器了也会关断，从而该点电压下降（因为外部电阻），当该点电压下降到低于0.35V时，IC会重新启动，因此，在短路条件下转换器会工作在间歇状态，输入平均功率非常低。

3，CF，时间电容：一个电容接在此脚与地之间，由内部电流发生器充电或放电，以此确定转换器的开关频率。

4，RFmin,设置最小的振动荡频率：此脚提供一下精确的2V参考电压，一个电阻接在此脚与地之间确定一个电流，此电流用来设定最小振动荡频率。

关闭反馈回路，通过调节振荡频率来调节转换器输出电压，光耦的光电三极管通过串联一个电阻接到此脚，此电阻将设定最大工作频率，一个R-C串联接于此脚与地之间，防止过多的能量涌入。

5，Stby，爆发模式工作门槛：此脚检测反馈控制电压，使之与一个内部参考电压（1.25V）比较，如果此脚电压低于参考电压，IC会进入空闭状态，静态电流会减少。

当此脚电压超过参考电压50mA时，IC会重启动，软启动不调节，如果不启用跳跃模式，应将此脚与RFmin脚联结在一起。

6，Isen，电流检测输入：此脚检测初级电流（通过一个电阻或一个电容无损的检测）。

L6599功能(中文)

1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。

它提供50%的占空比：在同一时间高端和低端180°反相。

输出电压的调整是通过调整工作频率来实现。

在高低端开关管的开关之间插入一个固定的死区时间来保证软开关的实现和能够工作于高频开关状态。

用自举方法驱动高端开关，IC整合了一个能够承受600V以上电压的高压浮动结构和一个同步驱动式高压横向双扩散金属氧化物半导体(DMOS)器件，节省了一个外部快速恢复自举二极管。

集成电路使设计师通过一个外部可设定的振荡器来设置转换器的工作频率范围。

启动时，为防止开机涌流，开关频率从一个可设定的启动极限频率逐步降低，直到控制回路达到稳定值为止。

这个频率变化是非线性的，它将输出电压过调降到最低限度；启动过程的时间可以设定。

在轻载状态下，集成电路可以被迫进入一个间歇脉冲工作模式，以便维持转换器的输入能量到一个最小值。

集成电路的功能包括非闭锁的低门限输入使用电流延迟作用或高门限的过流保护，当电流检测输入时，具有变频和延迟关闭自动重启两种方式。

如果第一级的保护不足以控制住主回路电流，高电平过流保护将闭锁集成电路。

它们的组合提供完全的过载和短路保护。

另外还有闭锁的过温和过压保护也很容易实现。

一个与PFC控制器的接口，可以在条件发生时，例如过流保护停机和闭锁式停机，或者在间歇脉冲工作状态，关掉PFC。

2 引脚设置2.1 引脚排列图1 引脚排列（顶视）2.2 引脚功能说明表1 引脚功能序号名称功能1 Css软启动端。

此脚与地（GND ）间接一只电容Css ，与4脚（RFmin ）间接一只电阻Rss ，用以确定软启动时的最高工作频率。

当Vcc （12脚）<UVLO （低电压闭锁），LINE （7脚）<1.25V 或>6V ，DIS （8脚）>1.85V （禁止端），ISEN （6脚）>1.5V ，DELAY （2脚）>3.5V ，以及当ISEN 的电压超过0.8V 并长时间超过0.75V 时，芯片关闭，电容器Css 通过芯片内部开关放电，以使再启动过程为软启动。

2 DELAY过载电流延迟关断端。

此端对地并联接入电阻Rd 和电容Cd 各一只，设置过载电流的最长持续时间。

当ISEN 脚的电压超过0.8V 时，芯片内部将通过150uA 的恒流源向Cd 充电，当充电电压超过2.0V 时，芯片输出将被关断，软启动电容Css 上的电也被放掉。

电路关断之后，过流信号消失，芯片内部对Cd 充电的3.5V 电源被关断，Cd 上的电通过Rd 放掉，至电压低于0.3V 时，软启动开始。

这样，在过载或短路状态下，芯片周而复始地工作于间歇工作状态。

（Rd 应不小于2V/150uA ＝13.3kΩ。

Rd 越大，允许过流时间越短，关断时间越长。

） 3 CF定时电容。

对地间连接一只电容CF，和4脚对地的RFmin 配合可设定振荡器的开关频率。

4 RFmin最低振荡频率设置。

4脚提供2V 基准电压，并且，从4脚到地接一只电阻RFmin，用于设置最低振荡频率。

从4脚接一只电阻RFmax，通过反馈环路控制的光耦接地，将用于调整交换器的振荡频率。

RFmax 是最高工作频率设置电阻。

4脚―1脚―GND 间的RC 网络实现软启动。

14 OUT高端门极驱动的浮地。

为高端门极驱动电流提供电流返回回路。

应仔细布局以避免出现太大的低于地的毛刺。

15 HVG高端悬浮门极驱动输出。

该脚能够提供0.3A的输出电流和0.8A 的灌入峰值电流驱动半桥电路的上端MOS管。

有一只电阻通过芯片内部连接到14脚（OUT）以确保在UVLO期间不悬浮驱动。

16 VBOOT高端门极驱动浮动电源。

在16脚（Vboot）与14脚（OUT）间连接一只自举电容Cboot，被芯片内部的一个自举二极管与低端门极驱动器同步驱动。

这个专利结构替换通常使用的外在二极管。

3 典型系统框图图2 典型系统框图4 电气数据4.1 极限参数表2 极限参数符号引脚参数值单位V BOOT16 浮电源电压 -1～618 VV OUT14 浮地电压 -3～V BOOT-18V dV OUT/dt 14 浮地电压最大恢复速度 50 V/ns V CC12 IC电源电压（I CC≤25mA）自限 V V PFC_STOP9 极限电压（针打开） -0.3～V CC VI PFC_STOP9 极限灌入电流（针低电平）自限 AV LINEmax7 极限针电压（I PIN≤1mA）自限 VI RFmin 4 极限输出电流 2 mA1～6，8 模拟输入和输出 -0.3～5 V 注：14、15和16脚的抗静电能力（ESD）保证在900V以上。