燃油暖风机操作手册
如何安全操作燃油暖风机
如何安全操作燃油暖风机燃油暖风机是一种常见的暖气设备，它利用燃油作为燃料，通过点火加热空气来达到取暖的目的。
然而，由于燃油暖风机具有燃烧过程，如果不正确使用，可能会产生火灾或爆炸等安全风险。
因此，在使用燃油暖风机之前，需要了解相关的安全操作要点。
1. 购买合格产品在购买燃油暖风机时，需要选择正规厂家生产的产品，且产品必须符合国家相关标准。
此外，需要注意以下几点：•燃油暖风机的外观和标识应清晰明了，硬件设施完好，无明显损伤或变形。
•燃油暖风机的使用说明书应包含详细和准确的安全操作要点，使用者必须认真阅读并遵照操作说明进行使用。
2. 安装燃油暖风机在安装燃油暖风机时，需要把握以下几点：•安装燃油暖风机的场所必须具备充足的通风条件，以保证排出燃烧产物，防止一氧化碳中毒等安全问题发生。
•安装燃油暖风机的位置应稳妥，且远离易燃物品和易燃气体。
如果需要室内使用，需要特别注意空气质量和通风情况。
•在使用前，需要检查管路、阀门及电气部分是否有漏气、漏油，如果发现异常应立即进行处理。
3. 操作燃油暖风机在操作燃油暖风机时，我们需要遵守以下注意事项：•启动燃油暖风机前，需要检查所有电气设施的状态，确保没有损坏和短路等问题。
同时，也需要检查燃油暖风机的燃油和气体管路是否正常。
•在点火前，需要开启通风窗，通风时间至少10分钟以上。
•操作燃油暖风机时，最好不要离开房间，以便随时发现异常情况。
•操作完毕后，需要关闭燃油暖风机并断电、关闭阀门。
4. 定期维护燃油暖风机对于燃油暖风机，定期的保养和维护显得尤为重要，具体措施如下：•定期清洗过滤器和燃烧室，保持燃烧均匀、充分，同时也能延长设备的使用寿命。
•定期检查管路、电气、阀门等部件是否存在老化、损坏、松动等安全隐患，勤于发现和处理问题。
•如果长时间停用燃油暖风机，需要将燃油和气体管路等全部拆卸并进行清洁、保养，并且存放在干燥通风的地方。
燃油暖风机的使用需要非常小心谨慎，一定要注意安全操作，防止发生意外。
柴油暖风机使用方法
柴油暖风机使用方法
柴油暖风机是一种常见的取暖设备，它使用柴油作为燃料来产生热量。
以下是柴油暖风机的使用方法：
1. 准备工作，首先，确保柴油暖风机放置在通风良好的地方，远离易燃物品和儿童。
然后检查柴油供应，确保柴油箱中有足够的柴油。
2. 加注柴油，打开柴油箱盖，将清洁的柴油倒入柴油箱中。
注意不要溢出或者漏出柴油。
3. 启动预热，在点火之前，需要进行预热。
打开暖风机的预热开关，让暖风机运行几分钟，直到燃烧室内的温度达到点火温度。
4. 点火，关闭预热开关，打开点火开关，启动柴油暖风机的点火系统，确保点火正常。
5. 调节温度，一旦点火成功，可以通过控制面板上的温度和风速调节按钮来调节所需的温度和风速。
6. 使用注意事项，在使用柴油暖风机时，要注意避免长时间连续使用，定期清洁滤网和燃烧室，保持通风良好，避免柴油泄漏和火灾危险。
总的来说，使用柴油暖风机需要注意安全和正确操作，确保设备正常运行，达到取暖的效果。
希望以上信息能够帮助到你。
24v柴油暖风机说明书
24v柴油暖风机说明书
24V柴油暖风机是一款采用柴油发动机驱动的工业排风机，常用于工厂、机械厂、化工厂、仓库、通风室等场所的通风净化和暖风循环，是实
现有效通风、排放污染物和暖风循环的理想设备。
1、24V柴油暖风机具
有节能环保、质量可靠、结构紧凑、噪音低，操作及维护简单等特点。
2、24V柴油暖风机采用柴油发动机驱动，配置比较完善，可以满足不同的工
况要求，燃油的消耗量低，作业时间长，安全可靠。
3、24V柴油暖风机
采用先进的风机设计，风量大，噪音低，满足安全环保的要求。
4、24V
柴油暖风机配置油箱，可在外放置，让机组空间更大，更加灵活方便。
5、24V柴油暖风机可采用控温系统，进行温度自动控制，以满足不同需求。
FVO-200RC 燃油取暖器使用说明书
OPERATING INSTRUCTIONS MANUAL(Please retain for future reference)ForFVO-200RC INDIRECT FIRED SPACE HEATERSCERTIFIED FOR USE IN CANADA AND U.S.A.As per CSA B140.8 Portable Oil Fired Heaters / CSA B140.02003 Oil Burning EquipmentUL733 Oil fired heatersConstruction Heaters Unattended Type.Issue date:2003325FLAGRO INDUSTRIES LIMITEDST. CATHARINES, ONTARIOCANADAGENERAL HAZARD WARNING:FAILURE TO COMPLY WITH THE PRECAUTIONS AND INSTRUCTIONS PROVIDED WITH THIS HEATER, CAN RESULT IN DEATH, SERIOUS BODILY INJURY AND PROPERTY LOSS OR DAMAGE FROM HAZARDS OF FIRE, EXPLOSION, BURN, ASPHYXIATION, CARBON MONOXIDE POISONING, AND/OR ELECTRICAL SHOCK.ONLY PERSONS WHO CAN UNDERSTAND AND FOLLOW THE INSTRUCTIONS SHOULD USE OR SERVICE THIS HEATER.IF YOU NEED ASSISTANCE OR HEATER INFORMATION SUCH AS AN INSTRUCTIONS MANUAL, LABELS, ETC. CONTACT THE MANUFACTURER.WARNING:FIRE, BURN, INHALATION, AND EXPLOSION HAZARD. KEEP SOLID COMBUSTIBLES, SUCH AS BUILDING MATERIALS, PAPER OR CARDBOARD, A SAFE DISTANCE AWAY FROM THE HEATER AS RECOMMENDED BY THE INSTRUCTIONS. NEVER USE THE HEATER IN SPACES WHICH DO OR MAY CONTAIN VOLATILE OR AIRBORNE COMBUSTIBLES, OR PRODUCTS SUCH AS GASOLINE, SOLVENTS, PAINT THINNER, DUST PARTICLES OR UNKNOWN CHEMICALS.WARNING:NOT FOR HOME OR RECREATIONAL VEHICLE USE.WARNING:INTENDED USE IS PRIMARILY THE TEMPORARY HEATING OF BUILDINGS UNDER CONSTRUCTION, ALTERATION, REPAIR OR EMERGENCIES ONLY.This heater is designed and approved for use as aconstruction heater under CSA B140.8 Portable OilFired Heaters / CSA B140.02003 Oil Burning Equipment& UL733 Oil Fired heaters.We cannot anticipate every use which may be madeof our heaters. CHECK WITH YOU LOCAL FIRESAFETY AUTHORITY IF YOU HAVE QUESTIONSABOUT APPLICATIONS.Other standards govern the use of fuel gases and heatproducing products in specific applications. Your localauthority can advise you about these.SPECIFICATIONSModel …………………………………………………….…. FVO-200RC Input ………………………………………………... BTUH Range185,000 Btu Fuel …………………………………………………………. No.1, No. 2,diesel orkerosene Fuel Pressure …………………………………………….... 180 psi Nozzle ………………………………………………………. 1.10 x 70A Electrical …………………………………………………… 115V 15 AMP Ignition ………………………………………………………. Direct SparkIgnition …….……………………………………………...…. ThermostatControlAir Circulation ………………………………………………. 2600 cfm Fuel Consumption ………………………………………...... 1.30 Gal/hr Approved …………………………………………………...... cETLus listedINSTALLATION:The installation of this heater for use with No.1, No.2, Diesel or Kerosene and shall conform with local codes or, in the absence of codes, with the National Fuel Gas Code ANSI Z223.1/NFPA 54. For recommended installation practices refer to CSA Standard B139.CLEARANCE TO COMBUSTIBLES:TOP FRONT SIDES REAR FLUE PIPE3 ft 10 ft 1 ft 2 ft 3 ft FUEL:This heater will operate with No.1, No.2, Diesel or Kerosene.Note:No.1 Fuel Oil or Kerosene must be used fortemperatures less than –10º C (8º F).ELECTRICAL:WARNINGElectrical Grounding InstructionsThis appliance is equipped with a three-prong (grounding)plug for your protection against shock hazard and should beplugged directly into a properly grounded three-prongreceptacle.115v supply must be available. Please note that the heaterrequires 15 amps for proper operation. Ensure appropriategauge extension cord is used.• 12/3 AWG at 50 Feet• 10/3 AWG at 100 FeetPOWER SUPPLY INDICATOR LIGHT:The power supply indicator light will help detect any faulty power supplied to the heater such as; grounding issues, reverse polarity or missing/poor connections.Warning Light IndicationsGreen Light ……………… Meets Power RequirementsSolid Red Light………….. Reverse PolaritySolid Red & Green Light… Ground IssueATTENTION: IF SOLID RED & GREEN IS INDICATED, MAKE CORRECTIONS TO POWER SUPPLY BEFORE TURNING HEATER ON. FAILURE TO DO SO WILL VOID ANY WARRANTY.FLUE PIPE: Flue pipe connection must terminate with a vertical run at least 2ft long. Horizontal runs should have a rise ratio of 1 in10 away from the heater. The chimney should have a 0.2”W.C. draft to ensure safe operation of the unit.The vent outlet on the heater is 6” diameter. Certified ventingmust be used at all times. Vent cap should be installed insituations where downdrafts occur. All venting mustcorrespond with the CSA B149 standard or in its absence,local codes.FV SERIES CONSTRUCTION HEATER – VENTINGREQUIREMENTS1. VERTICAL FLUE TERMINATIONSFLUE OUTLET OF HEA2. HORIZONTAL FLUE TERMINATIONSFLUE OUTLET OF HEAALLA - VENT TERMINATION MUST BE A MINIMUM OF 2FT HIGHER THAN ANY POINTWITHIN 10FT.B - MAXIMUM HORIZONTAL RUN IS 30FT.NOTE: 90deg ELBOW = 10ft HORIZONTAL VENT ALLOWANCE45deg ELBOW = 5ft HORIZONTAL VENT ALLOWANCEC - VENT TERMINATION IN HORIZONTAL POSITION MUST BE MINIMUM 4ft FROM ANYCOMBUSTABLE SURFACED - EXTERIOR VERTICAL VENT TERMINATION MUST BE A MINIMUM OF 2ft.NOTE: ALL VENT TERMINATIONS MUST HAVE A RAIN CAP INSTALLED AS PER LOCAL CODE REQUIREMENTS..OUTLET DUCTING:Hitex heater duct with a minimum temperature handling of300 deg F including wire reinforcement to prevent collapsing.Heater is designed for use with 1 x 12” (FV-HD12) or 1 x 16”(FV-HDG16) diameter ducting equipped with pin lock or cuff& buckle provided on collar of ducting. Ducting should beinspected periodically for tearing and/or wear marks.Ducting should be stored in a dry area when not in use. INLET DUCTING:Inlet ducting can be used on the return air inlet of heater.The heater is designed for 12” inlet diameter ducting with pinlock or cuff and buckle system.MAINTENANCE:1. Every construction heater should be inspected before each use, and atleast annually by a qualified service person. Incorrect maintenance my result in improper operation of the heater and serious injury could occur.2. The hose assemblies shall be visually inspected prior to each use of theheater. If it is evident there is excessive abrasion or wear, or the hose is cut, it must be replaced prior to the heater being put into operation. The replacement hose assembly shall be that specified by the manufacturer.3. The flow of combustion and ventilation air must not be obstructed. Be sure tocheck the fan assembly and ensure that the motor and blade are operating properly.4. Compressed air should be used to keep components free of dust and dirtbuild up. Note: Do not use the compressed air inside any piping or regulator components.5. Change fuel filter insert (Part# FVO-418) once per month. Change fuel filtercartridge (Part# FVO-419) once every 6 months.6. Change oil nozzle (Part# FV-235B) once per year.7. Fan Limit Switch (Part# FV-407A) should be replaced if the fan motor doesnot shut off after the heat exchanger has cooled down.8. The High Limit Switch (Part# FV-406) should be checked each season. Thislimit switch will ensure the burner shuts down if the temperature exceeds 250ºF at the outlet.9. Fuel tank should be drained on a regular basis by removing drain plug.10. CAUTION– Do not have any source of ignition near the heater whendraining tank.NOTE:No.1 fuel oil or kerosene is recommended for temperatures below-10º C / 8º F.11. Heat Exchanger should be cleaned if smokey conditions continue even afterthe air adjustments on the burner are made.START UP INSTRUCTIONS:1. Position heater properly on a level surface.2. Be sure the toggle switch in is the “OFF” position.3. Ensure burner “air gate” is properly set at 3.4. Ensure electrical cord is grounded and plugged into a 120V 15AMPoutlet. Verify cord size (12/3AWG at 50ft & 10/3AWG at 100ft)5. The power indicator light on the control box will engage. If the greenlight illuminates, you have proper power supply. If not, refer to stickeron heater to verify warning problem. Correct power supply problembefore operating heater.6. Move toggle switch to “MANUAL” position for manual control.7. Move toggle switch to “THERMOSTAT” position for thermostat control.Thermostat must be plugged into heater first.Please Note:1. If using Thermostat on unit, unit must be started in Thermostat position.2 When changing between manual and thermostat operation, the heatermust be left in the “OFF” position for 30 seconds to prevent the burner from locking out.3. When using a generator for electrical supply, make sure the generatoris properly grounded and generator is at a 60Hz frequency.4. In the event that a Generator is being used and the generator runs out offuel, make sure the heater switch is in the “OFF” position before restarting generator, failure to do so may damage heater.TO SHUT DOWN:1. Move toggle switch to “OFF” position. Do not disconnect power supplyuntil the heat exchanger cools downNOTE: Fan will continue to operate after the burner shuts down. Once the unit cools down, the fan will stop.IF HEATER FAILS TO START:1. Press manual reset button at rear of burner.2. Check fuel level. There must be 2-4 gallons of fuel in the tank for theheater to start properly.3. Make sure there are no air locks in fuel lines or filter.4. Ensure proper power supply and extension cord is being used.5. Check for dirty fuel filter or blocked fuel supply line.6. Check burner nozzle assembly.NOTE: IF THE BURNER HAS BEEN RESET SEVERAL TIMES THERE MAY BE AN ACCUMULATION OF OIL IN THE CHAMBER! DO NOT CONTINUE TO TRY AND START THE HEATER!DRAIN OIL FROM HEAT EXCHANGER USING DRAIN HOLE AT FRONT OF HEAT EXCHANGER FOR 15-20 MINUTES BEFORE ATTEMPTING TO RELIGHT. LET REMAINING EXCESS OIL BURN OFF BEFORE CHECKING COMBUSTION OF UNIT.SAFE OPERATION PRECAUTIONS:1. Do not fill fuel tank while heater is operation.2. Do not attempt to start heater if excess oil remains in the heatexchanger.3. Use switch to shut down the heater. Do not try to shut down the heaterby unplugging the electrical cord.4. Do not plug anything other than the thermostat into the “Thermostat”plug.5. Do not use any fuel other that those listed on rating plate.6. Follow electrical requirements shown on rating plate and/or Electricalrequirements section of this manual.7. Before removing any guards or performing any maintenance, be surethat the main power supply is disconnected.COMBUSTION AIR ADJUSTMENTS:NOTE: Proper combustion air adjustment must be achieved using a certified combustion analyzer and smoke tester to ensure completecombustion.The air adjustment should be made to achieve 10% CO2and No. 1 or “trace” smoke. (Bacharach Scale)SETTING THE AIRADJUSTMENT PLATEA) Regulation of the combustion airflow is made by adjustment of themanual AIR ADJUSTMENT PLATE (1)after loosening the FIXING SCREWS(2 & 3). The initial setting of the airadjustment plate should be madeaccording to Column 5 in the BurnerSet-up Chart.B) The proper number on the manualAIR ADJUSTMENT PLATE (1) shouldline up with the SETTING INDICATOR(4) on the fan housing cover. Once set, the air adjustment plate should be secured in place by tightening SCREWS 2 and 3.C) The final position of the air adjustment plate will vary on each installation. Use instruments to establish the proper settings for maximum CO2and a smoke reading of zero.NOTE: Variations in flue gas, smoke, CO2and temperature readings may be experienced when the burner cover is put in place. Therefore, the burner cover must be in place when making the final combustion instrument readings, to ensure proper test results.BURNER SET-UP CHART1 2 3 4 5ACTUAL FIRING RATE± 5%NOZZLESIZEPUMP PRESSURETURBULATORSETTINGAIRDAMPERSETTINGGPH GPH PSI BAR1.30 1.10 x 70°A 180 12.41 33.5* Note – Air damper setting is typically set at 3.5 for operation in colder temperatures. A combustion analyzer should always be used when setting the burner.TEMPERATURE FEELER GAUGE ADJUSTMENT(ATTACHED TO FAN SWITCH)The temperature feeler gauge is required to be always touching the heater exchanger.The temperature feeler gauge controls the air flow over the fan switch, which eliminates any unnecessary fan cycling. The temperature feeler gauge can be adjusted for different outside temperatures, by rotating the location of the temperature feeler gauge holes. This will provide maximum performance of the unit in different applications.If supply air is warm (-5º C, indoor application):Turn the temperature feeler gauge so that the holes are parallel with the heat exchanger. This will help the fan switch to remain cool and not overheat. See following:If supply air is cold (under -5ºC):Turn the temperature feeler gauge so that the holes are closed off as the air goes over the heat exchanger. This will reduce fan cycling and the unit from shutting down. See following:In extreme cold conditions, cover the holes on the temperature feeler gauge using foil tape or replace feller gauge with part# FV-433B Solid feeler gauge. Ensure that the temperature feeler gauge is readjusted for warmer weather conditions. Failure to do so may result in burning out fan switches- not covered under warranty.been made, or failure of the pump shaft seal may occur.WARNING: If a neutral or ground lead is attached to this terminal, the CONTROL BOX on the burner will be damaged should lockoutoccur.INSERTION / REMOVAL OF DRAWER ASSEMBLYA) To remove drawer assembly, loosen SCREW (3), then unplug CONTROLBOX (1) by carefully pulling it back and then up.B) Remove the AIR TUBE COVER PLATE (5) by loosening the two retainingSCREWS (4).C) Loosen SCREW (2), and then slide the complete drawer assembly out of thecombustion head as shown.D) To insert drawer assembly, reverse the procedure in items A to C above, andthen attach fuel line to the pump.NOZZLE PLACEMENTA) Remove the NOZZLE ADAPTER (2) from the DRAWER ASSEMBLY byloosening the SCREW (1).B) Insert the proper NOZZLE into the NOZZLE ADAPTER and tighten securely(Do not over tighten).C) Replace adapter, with nozzle installed, into drawer assembly and secure withscrew (1).ELECTRODE SETTINGTURBULATOR SETTINGA) Loosen NUT (1), then turn SCREW (2) until the INDEX MARKER (3) is alignedwith the correct index number as per the Burner Set-up chart, on page 12.B) Retighten the RETAINING NUT (1)NOTE: Zero and five are scale indicators only. From left to right, the first line is5 and the last line 0.OIL LINE CONNECTIONSNote:Pump pressure must be set at time of burner start-up. A pressure gauge is attached to the PRESSURE PORT (8) for pressure readings. Two PIPE CONNECTORS (5) are supplied with the burner for connection to either a single or a two-pipe system. Also supplied are two ADAPTORS (3), two female 1/4” NPT, to adapt oil lines to burner pipe connectors. All pump port threads are British Parallel Thread design. Direct connection of NPT threads to the pump will damage the pump body. Riello manometers and vacuum gauges do not require any adaptors, and can be safely connected to the pump ports. An NPT (metric) adapter must be used when connecting other gauge models.PARTS LIST FOR FVO-200Part Number Part DescriptionFV-2011/2 HP Fan MotorFV-202RC14" BC Impeller For FV-200RCFV-202RCA Venturi For 14" BC ImpellerFV-20312" WheelFV-20412" Power Cord c/w Plug EndFV-205SS Heat Exchanger40-113-D3.5GALV1/2" X 3.5" Galvanized Nipple40-108-8GALV1/2" Galvanized CapFV-406High Limit Switch (Outet) 250FFV-407A Fan Limit Switch (Adjustable)FV-407G Fan Limit Silicone GasketFV-207Lockable Caster WheelFV-270Fan Motor CanopyFV-409Toggle Switch (on control box)FV-411Red Light (on control box)FV-214Thermostat Plug (on box control) (Prior to 2011)FV-414B Thermostat Plug (on box control) (As of 2011)FV-215Female Connector for FV-TH2 (Prior to 2011)FV-415A Male Connector for FV-THB ( As of 2011)FVO-215Riello F5 Burner (Oil)FVO-21623 US Gallon Oil Tank (Steel)FVO-216G Fuel GaugeFVO-417Oil Tank Cap121-B Oil Tank Drain PlugFVO-418Fuel Filter (Complete)FVO-419Fuel Filter (insert Only)FVO-220Clear Fuel Line 6" (Tank to Filter)FVO-221Clear Fuel Line 7.5" (Filter to Burner)FVO-222Clear Fuel Return Line (Burner to Tank)48-6B Brass Fitting (Tank to inlet Fuel Line)48-6C Brass Fitting (Inlet Side of Filter)2103-C-CGA3/8" Shut Off Valve122-C3/8" Brass Hex Nipple50-6C3/8" FP X 3/8" MP Brass Elbow49-6C3/8" MP X 3/8" F.FL Brass ElbowFV-461Inlet/Outlet Burner Pump FittingFVO-2237" Copper Pick Up Tube c/w AdapterFV-231Burner GasketFV-433Feeler GaugeFV-234Front Face Plate (1 x 12")FV-235B Oil Burner Nozzle (1.10 x 70A)FV-437High Limit (Rear) 150FFV-240Wheel Axle - FV-200 SeriesFV-446Sight Glass c/w Fiber GasketFV-447Sight Glass WasherFV-449SI Smart Indicator LightFVO-3000443Pump Drive KeyFVO-3002278Sub Base for F10/F5 BurnerFVO-3002279Coil -F10/F5 BurnerFVO-3002280Photo Cell - F10/F5 BurnerFVO-3005844Capacitor F10/F5 BurnerFVO-3005855Mounting Flange for F10/F5 BurnerFVO-3005869Electrode PorcelainFVO-3005880Electrode AssemblyFVO-3006553Coil U-Bracket c/w Knurled NutFVO-3006965Nozzle Adapter F10/F5 BurnerFVO-3006966Electrode Support for F10/F5 Burner FVO-3006974Nozzle Oil Tube F5 BurnerFVO-3006977Turbulator Disc for F5 BurnerFVO-3006992Pipe Connector - SupplyFVO-3006993Pipe Connector - ReturnFVO-3007320Acoustic Liner for Burner Back Cover (F5) FVO-3008631Electrode AssemblyFVO-C7001010Pump AssemblyFVO-C700-1029Ignition Module (Oil Burner)ACCESSORIES FV-HD1212" x 12FT HiTex Ductingfv-hd12x2512" x 25FT Hitex DuctingFV-THB Thermostat c/w 25FT Cord ( As of 2011)FV-VK6" x 3FT C-Vent c/w Rain CapFVO-C7001001Emergency Service Kit (Oil Burner)FVO-C7050010Vaccum & Pressure Tester ManifoldFV-432Pressure Gauge Adapter。
燃油暖风机
燃油暖风机简介燃油暖风机是一种使用燃油作为燃料的暖风设备。
它能够将燃油燃烧产生的热能转换为热空气，从而提供温暖的空气。
燃油暖风机具有加热快、供暖效果好、使用方便等特点，可以广泛应用于建筑工地、仓库、车间、车辆、农业设施、矿井等场所。
工作原理燃油暖风机的工作原理是在燃油与空气充分混合的情况下，点燃混合气体，使其燃烧产生热能，并将热能转换成热空气。
具体的工作流程如下：1.燃油泵将燃油从油箱中抽取到燃烧器中。
2.燃油混合器将空气和燃油混合成为可燃气体。
3.点火器在混合气体进入燃烧器时点燃混合气体。
4.燃烧产生的热量通过燃烧室内的管道将空气加热，在风扇的作用下，将加热后的空气吹出去。
分类根据燃料种类不同，燃油暖风机可以分为柴油暖风机和液化气暖风机两种。
柴油暖风机柴油暖风机是指使用柴油作为燃料的暖风设备。
柴油暖风机具有加热速度快、使用方便等优点，是广泛运用于工地、车辆、船舶等领域的一种暖风设备。
但是柴油暖风机也存在柴油燃烧不完全产生的有害气体等问题，需要定期进行清洗和维护。
液化气暖风机液化气暖风机是指使用液化气作为燃料的暖风设备。
液化气暖风机具有供暖稳定、使用方便等优点，是广泛运用于居民、商业等场所的一种暖风设备。
但是液化气暖风机也存在燃烧不完全产生的有害气体等问题，需要在使用过程中加强安全防范。
使用注意事项1.在使用前，需要对燃油暖风机的安全防范措施、使用方法进行了解，并按照说明书正确使用燃油暖风机。
2.在使用过程中，要禁止打火机、火柴等明火靠近燃油暖风机。
3.在使用过程中，要加强对燃油和气源管道的检查，并在发现问题时及时维修或更换。
4.在使用过程中，要经常对燃油暖风机进行清洗和维护，确保燃油燃烧完全，避免产生有害气体。
结尾燃油暖风机是一种供暖设备，它能够将燃油燃烧产生的热能转换为热空气，从而提供温暖的空气。
在运用燃油暖风机时，需要注意安全事宜，并经常进行检查和维护。
总之，应该在保证供暖效果的前提下，切实遵守安全操作规程，确保使用燃油暖风机的安全性。
燃油热风烘炉操作规程
燃油热风烘炉操作规程
1、操作前检查各类开关是否正常运转，是否出现漏电或者短路现象，操作者做好防触电措施。
2、操作前检查油缸里的柴油是否足够，并由专门人员每天定时对烘炉添加柴油。
3、清理烘炉内残留的工件杂物，检查仪表、冷却泵、燃油、风机等是否正常，变速箱是否要加油等。
4、启动时，操作人员要检查燃油火枪是否开动，当燃油火枪不着时，马上通知车间主管部门修理，以免耽误生产。
5、生产线启动运作时，操作人员要检查是否有异物阻碍运作（如：生产线轮子脱离轨道等），马上通知车间主管部门修理。
6、将烘炉的温度表调整到所需的温度，然后加温，视坯件而调节烘炉的温度和转速，需要调整的必须由主管部门人员来调整，并观察是否在预定的时间内达到预定的温度。
7、调整生产线的速度，使之符合工件烘干所需要的时间。
8、出炉后经检查合格的工件，使用适当的工装箱，并用纸分隔装好，堆放稳妥。
对要补油的工件应小心在有缺陷的地方补上，不可胡乱扩大补油面积。
9、不合格品放在红线区处理，并作标识。
10、结束时，先关闭烘炉（火枪），再关闭流水线，然后是排风设备，直到全部设备完全静止为止。
燃油热风炉使用说明书
目录一、概述……………………………………………………二、工作原理…………………………………………………三、规格与技术参数…………………………………………四、安装调试与操作使用规程…………………………………五、维护保养与常见故障的排除………………………………六、安全事项…………………………………………………CONTENTSⅠ.I n t r o d u c t i o n……………………………………………Ⅱ.Wo r k i n g P r i n c i p l e s………………………………………Ⅲ. Specifications and technique instruction …………………Ⅳ. Installation adaptation and operation instruction…………Ⅴ. Care and maintenance and remove of common fault………Ⅵ.S a f e i t e m s…………………………………………………一、概述YR系列燃油热风炉是我公司在多年实践的基础上自行研制开发的一种高效节能燃油供热设备，供热能力为1×4.18×106kJ/h~30×4.18×106kJ/h。
热风炉主要由燃料供应装置、供风装置、燃烧装置、燃烧室、混合室及热工控制系统组成。
本产品结构简单、体积小巧、操作安全、维护简便、使用寿命长、供热范围广，温度可随意调配，广泛应用于水泥、化工、冶金等行业中的烘干、焙烧设备提供热源。
二、工作原理燃油热风炉工作原理：燃料由供应装置安全输送到燃烧器，与供风装置送入的空气经燃烧器组织在燃烧室里充分燃烧，产生的高温气体在混合室内与冷空气混合得到符合工艺要求的热烟气。
三、规格与技术参数㈠产品型号YR-nD（Z、G）n=1~30，n=1表示1×4.18×106kJ/h供热能力G表示高温型，供热温度为600~1200℃Z表示中温型，供热温度为300~600℃D表示低温型，供热温度为100~300℃燃油热风炉四、安装调试与操作使用规程㈠安装炉体安装：炉子要安装在牢固的基础上,各连接法兰之间应加石棉绳密封,详见燃油热风炉安装图。
柴油暖风机安全操作规程
柴油暖风机安全操作规程
《柴油暖风机安全操作规程》
一、操作前的准备
1. 在使用柴油暖风机之前，必须先检查机器的外观是否完好，各个部件是否牢固。
2. 确保柴油暖风机的油箱中有足够的柴油，同时油箱盖要紧固好，以防止柴油泄漏。
3. 将柴油暖风机放置在平稳的地面上，避免在使用过程中出现不稳定情况。
二、操作过程中的注意事项
1. 柴油暖风机在使用过程中必须保持通风良好，禁止在密闭的环境中使用，以免产生一氧化碳中毒的危险。
2. 在启动柴油暖风机之前，应该按照说明书的方法进行操作，确保启动过程顺利进行。
3. 在加注柴油时，必须停止加热并确保机器冷却后再进行，以免发生燃烧事故。
4. 柴油暖风机的使用环境中，不宜堆积易燃易爆的物品，以免引发火灾。
5. 在使用过程中，要随时检查燃烧是否正常，如发现异常应该立即停止使用并排除故障。
6. 对于长时间未使用的柴油暖风机，要进行定期检查和保养，确保机器的可靠性和安全性。
三、操作后的清理
1. 在使用结束后，应将柴油暖风机放置在通风良好的地方，待
机器冷却后进行清理和维护。
2. 清理过程中，要确保机器的各个部件都处于关闭状态，并且机器处于断电状态。
3. 清理的工具要放置在安全的地方，以免造成人员伤害。
通过遵循《柴油暖风机安全操作规程》，可以有效的保障设备的安全使用，减少事故的发生概率，提高工作效率，保护人员的安全。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
燃油暖风机操作手册
燃油暖风机简单的来说就是通过燃油的燃烧，对空气进行加热。
主要的用途就是以其高效性为需要即时供暖的地方提供高热量。
最适用于开放或通风良好的地方，如工厂、仓库、施工现场等。
燃油暖风机在操作的过程需要注意很多方面，正确、谨慎地使用燃油暖风机，才会让危险远离。
以下就如何正确的使用燃油暖风机作出了明确的指导。
一、燃料必须根据不同的环境温度使用规定的0#至-35#柴油，或者同类煤油，避免燃油发生结冻，结蜡现象，以免燃油工业取暖器发生堵塞油管及喷嘴。
二、燃烧室内部温度高达800摄氏度以上，严禁用手触摸其发热部位，且风口前面禁止堆放易燃易爆物品，严禁儿童在设备周围打闹嬉戏。
三、为保证燃料的输送顺畅，及燃烧效率等，油箱内及油泵内的过滤网至少每工作500小时进行一次清理，以保证机器的无故障运转。
四、严禁在短时间内多次对燃油工业取暖器进行关闭开启动作，这样容易造成多次电流过大可能会对主板或者其它电器元件造成瞬间多次冲击，可能会损毁这些部件。
五、关闭设备后，严禁立刻拔掉电流插头，因为刚关机时内部仍然拥有很高的温度，所以其会继续散热降温，当温度低于安全值之后，才会彻底停机。
六、每日使用时对其进行一些必要的检查，如油位是否符合最小启动位，电路是否安全等。
七、如果燃油工业取暖器需要长期闲置，需要将其进行拆解，并按原包装方式进行装箱保存，并将旋转在干燥，通风的空间内，避免腐蚀，并应定期对其进行试运转，避免长期不使用造成的报废。
八、如有必要，每隔一年对产品进行一定定期的全面检查，包括燃烧系统、供油部分、控制部件等各方面零件及元配件。
九、气泵低压系列的产品需要每工作200小时就将海绵垫拿出清理灰尘，清灰过程非常简单，用手单单即可，然后再放回原位。
十、由于电机转速过快，机器运转时，严禁将任何异物塞进其内部，避免和风扇接触而发生危险。
随着人们对供暖要求的变高，燃油暖风机也在不断的改进中，力求在使用上更加便捷，供暖效果更好，经济成本更加节约。
在使用燃油暖风机之前，请仔细阅读该操作手册，避免引起不必要的损害。