hs白雪崩能天使说明书修正版
FOX Snow Float 3 和 Zero 系列悍马手册说明书

Quick Switch Compression KnobQUICK SWITCH WITH COMPRESSION EXPLAINEDThe Quick Switch Compression adjust feature gives you the ability to easily adjustthe shock’s compression damping with three easy clicks. Adjustments are made by turning the adjuster knob on the body cap located on the end of the shock absorber. The Quick Switch Compression adjuster has three clicks of adjustment. The factory setting is in the second, middle click. The performance of the shock at this setting is close to the performance of the non-adjustable shock and is a good all-around setting. For firmer compression, turn the knob clockwise. For softer compression, turn theCompression damping affects how quickly the shock reaches full bottom-out. Adjusting the compression affects how quickly the shocks compress when bumps orThe optimum compression setting usually requires the least amount of damping possible without bottoming out the shock. Firmer compression damping will typically be felt as harsh at slow speeds but plush at high speeds, large g-outs, and jumps. Firmer compression damping on ski shocks may provide more stability when cornering on the trail but can also make it more difficult to get the sled leaned over when boon docking. Switching a rear shock to Lockout mode (if equipped) will increase ski pressure, improve traction in deep snow, and improve transfer on top of the snow. The benefits of Lockout mode can provide superior stability when riding deep off-trail snow, hill climbing, and boon docking.Do not leave the rear track shock in Lockout mode when riding on the trail.This can create extremely high internal pressures.。
hg能天使说明书电子版

hg能天使说明书电子版
1、墙上安装:在选定的安装位置打两个直径为8毫米的孔。
放进随机携带的塑料胀栓,旋进螺钉,挂上主机并旋紧螺钉。
2、橱柜内安装:可不用打孔固定,选好位置放稳即可。
沈阳纯净水机,沈阳家用纯水机,沈阳反渗透纯水机无论在墙上安装还是在橱柜内安装,均应考虑将来更换滤芯和维修的方便性。
特别是橱柜内安装时,要把水机放在橱柜门外进行安装操纵。
3、安装鹅颈龙头预备:在客户选定的位置上安装。
如鹅颈龙头要安装在厨房的调理台面上,应在调理台面上钻一个直径为12毫米的孔。
如鹅颈龙头安装在墙上,应在选定的位置上,按支架的孔距钻两个直径为6- 8毫米的孔,塞进塑料胀栓,用自攻螺钉将支架固定在墙上,然后顺序安装鹅颈龙头。
4、在大理石台面上打孔时,应使用专用钻头,用定位板进行定位。
在仿大理石(合成材料)上打孔时,应使用普通麻花钻头。
此两种打孔均使用普通手电钻,切不可使用冲击钻。
5、安装储水桶上球阀:在储水桶螺纹处缠6-8圈密封胶带,旋进上球阀,然后以手力旋紧上球阀。
将储水桶安置到适当的安放位置。
6、安装鹅颈龙头:安装鹅颈龙头时,上面放大软胶圈,底部依次放小软胶圈、硬胶压板、金属垫圈。
hg暗物质能天使说明书

hg暗物质能天使说明书
此机体原先为结成达也与亚伦合力完成的惊异EXIA,除了武装、脚尖、脸部和天线外和惊异能天使完全一样,在总决赛前夕,真下会长为了绝对的胜利,让奈恩·巴托用具象化面具控制了结成,为了配合具象化系统,在机体表面涂上了紫红色的特殊颜料,配色也因此变成了宛如地狱君王一般的黑色与紫色。
在武装方面,将原本惊异GN剑的剑刃制成了另一把GN破坏剑,与原先的破坏剑一起装在腰部,可以双手拔出,并在两把破坏剑上加上了新的机能,能够操纵烈焰和寒冰这两种技能,用诡异的方式战斗,由于剑刃被用在了破坏剑上,所以GN战剑只剩下侧面的盾牌上的光束剑,保留了最基本的近战功能,因为采用了新技术,足以劈开了星创堪比卫星加农炮的全力炮击,威力可见一斑。
但可能是B 杜的技术还不足以还原原版能天使的战剑收纳机构的缘故,在剧中名人直接把武器给扔了出去作为攻击方法。
并且保留了手臂的GN火神炮的军刀模式,并且TRANS-AM推进器两翼下部可分离强化刺锥,同时分离后的头部可以发出强力炮击,另外不知道是为了减轻重量还是什么原因,本机没有装备惊异能天使的大型GN盾牌。
本机于24话登场,在一开始凭借强大的性能和结成出色的技术完虐星创,破坏剑的能力更是成了第一季最屌的特效,在坑道内(疑似)更是重创星创强袭将其打至无法行动。
只是,要是这样就能赢的话还叫主角吗······在艾拉,诚哥,043人坚定的信念下,星创依靠主角光环满血复活(真扯),并且依靠RG系统的BUG 性能一路开挂,最后暗物质能天使被星创强袭击中胸甲,漆面因巨大的冲击力而脱落,露出了里面的惊异能天使本体,结束了悲剧的一生。
产品调节说明说明书

C. GLASNOST: Upravlja skupni nivo glasnosti. D. VISOKI TONI: Modificira barvo tona v višjih frekvencah. E. SREDNJI TONI: Modificira barvo tona v srednjih frekvencah.
M. KONEKTOR NAPÁJACIEHO KÁBLA IEC A POISTKA: Slúži na pripojenie priloženého kábla, ktorého druhý koniec zapojte do uzemnenej zásuvky s napätím a frekvenciou uvedenou vedľa konektora. Ak potrebujete skontrolovať alebo vymeniť poistku, vytiahnite napájací kábel zo zásuvky a zapáčením otvorte kryt s poistkou pod konektorom. Poistku možno vymeniť iba za poistku rovnakého typu a rovnakých parametrov.
TYP PRÍKON A VÝKON VSTUPNÁ IMPEDANCIA VÝSTUPNÁ IMPEDANCIA REPRODUKTOR ELEKTRÓNKY POISTKA PRÍSLUŠENSTVO ROZMERY HMOTNOSŤ
Trynex SnowEx SP-3000 SP-6000 雪兜吹雪设备说明书

FoR ModElssP-3000 (Serial# K1-131116 and Higher)sP-6000(Serial# E1-712561 and Higher)800-725-8377This Manual Must Be Read Before Operating The Equipmentowner / operator’s ManualTable of ContentsGeneral Information (3)Introduction (4)Safety (5)Warning Decal Position ...............................................................................................................................................................................6-7 Operating the Spreader .. (8)Spreader Maintenance (9)General Wiring Instructions (10)Control and Harness Diagrams .............................................................................................................................................................. 11-15 Mounting Instructions .............................................................................................................................................................................16-17 Trobleshooting ...................................................................................................................................................................................... 18-19 Warranty . (20)Spreader ViewsModel # SP-3000/SP-6000 (21)Drive Assembly Parts BreakdownModel # SP-3000/SP-6000 ..................................................................................................................................................... 22-23 Auger Assembly Parts BreakdownModel # SP-3000/SP-6000 ..................................................................................................................................................... 24-25 Frame Assembly Parts BreakdownModel # SP-3000 .................................................................................................................................................................... 26-27 Frame Assembly Parts BreakdownModel # SP-6000 .................................................................................................................................................................... 28-29 Notes .................................................................................................................................................................................................... 30-31Have a question or need assistance?SnowEx Customer Care(800) 725-8377or (248) 586-3500Monday through Friday 8:00 AM to 4:30 PM ESTFax: (248) 691-8378E-Mail:******************************Website: General InformationCongratulations!The spreader you have purchased is an example of snow and ice control technology at its finest! Your spreader’s self-contained design is a trademark of all SnowEx products. Here’s why…simpliCity: Fewer moving parts manufactured of higher quality means minimal maintenance for your SnowEx spreader.reliability: High impact linear low density polyethelyne hopper. State-of-the-art electronic dual variable speed control, custom engineered powder coated frame, maximum torque 12-volt motor coupled to a custom engineered transmission; found only on SnowEx products.Versatility: Multi-use capabilities allows spreading of a variety of materials for snow and ice control.Warranty: Best in the industry, hands down! 2 years standard and now 5 year extended (optional).The benefits you are about to recognize are that of time, money and effort.We welcome you to the world of SnowEx Performance.RegistrationRecord the following information in this manual for quick reference.Spreader Model NumberSpreader Serial Number Controller Serial NumberDate of PurchaseDealer Where PurchasedWhen ordering Parts, the above information is necessary. This will help to see that you Array receive the correct parts.At the right is a diagram of the ID tag. This tag on the spreader is located on the frame.Please fill out the warranty card with all the necessary information to validate it.This will also give us a record so that any safety or service information can becommunicated to you.IntroductionThis manual has been designed for your help. It will assist you and instruct you on the proper set-up, installation and use of this spreader. Refer to the table of contents for an outline of this manual.We require that you read and understand the contents of this manual completely (especially all safety information) before attempting any procedure contained herein.this sign should alert you:The Society of Automotive Engineers has adopted this safety alert symbol to pinpoint characteristicsthat, if not carefully followed, can create a safety hazard. When you see this symbol in this manual or on themachine itself, be alert! Your personal safety and the safety of others is involved.Defined below are the safety alert messages and how they will appear in this manual:(red)Information that, if not carefully followed,can cause death!(orange)Information that, if not carefully followed,can cause serious personal injury or death!(yelloW)Information that, if not carefully followed,can cause minor injury or damage to equipmentSafetyBefore attempting any procedure in this book, these safety instructions must be read and understood by all workers who have any part in the preparation or use of this equipment.For your safety warning and information decals have been placed on this product to remind the operator of safety precautions . If anything happens to mark or destroy the decals, please request new ones from SnowEx.Never exceed the Gross Vehicle Weight Rating of vehicle. Failure to do so may limit a vehicles handlingcharacteristics.Never attempt to take a unit off a truck with material in it.Always keep hands, feet, and clothing away from power driven parts.Unit must be pinned and locked into position before operating vehicle.Always shut off vehicle and power source before attempting to attach or detach or service unit Be surevehicle/power source is properly braked or chocked.Remember, most accidents are preventable and caused by human error. Exercising of care and precautionsmust be observed to prevent the possibility of injury to operator or others!Never operate equipment when under the influence of alcohol, drugs, or medications that might alter yourjudgment and/or reaction time.Before working with the spreader, secure all loose fitting clothing and unrestrained hair.Always wear safety glasses with side shields when servicing spreader. Failure to do this could result inserious injury to the eyes.Never allow children to operate or climb on equipment.Always check areas to be spread to be sure no hazardous conditions or substances are in the area.Always inspect unit for defects: broken, worn or bent parts, weakened areas on spreader.Remember it is the owner’s responsibility to communicate information on safe usage and propermaintenance of all equipment.Always make sure personnel are clear of areas of danger when using equipment.Never weld or grind on equipment without having a fire extinguisher available.Inspect the unit periodically for defects. Parts that are broken, missing or worn out must be replacedimmediately. The unit or any part of it can not be altered without prior written permission from themanufacturer.Always inspect pins and latches whenever attaching or detaching spreader, and before operation of spreader.Never exceed 45 m.p.h. when loaded spreader is attached to vehicle. Braking distances may be increasedand handling characteristics may be impaired at speeds above 45 m.p.h.Never use wet materials or materials with foreign debris with any of these spreaders. These units aredesigned to handle dry, clean, free flowing material.Never leave material in hopper for long periods of time. Be aware that all ice melters are hygroscopic and willattract atmospheric moisture and harden up.Operating the SpreaderModel # SP-3000/SP-6000SPREADER LOADINGWarning – Do not overload vehicle. Use chart below to calculate weight of material. Weights of material are an average for dry materials.Material Weight Per Cubic Ft.Rock Salt 80-90 lbs.Sand/Salt Mix 95-120 lbs.• Warning – Never leave material in hopper for long periods of time as salt is hygroscopic and will attract atmospheric moisture and harden up. When spreading sand mix, a 1:1 ratio for Sand/Salt mix is recommended to prevent the material from freezing.Spreader Operation• The Dual Variable Speed Controller has dual finger-tip dials for maximum performance, digital system status with warning protection and built-in Vibrator Switch.• To start, press power switch on controller and spreader will accelerate to speed set on spinner and auger dials.• To stop, press power on controller to off position.• Speed of Auger and Spinner may be adjusted separately to get desired flow and spread distance• The Vibrator Switch is needed for dense material or to increase the flow to the Auger. This eliminates bridging of material in hopper.• A Material Baffle has been installed in your spreader to stop fine material from free flowing. If using dense or damp material, or if more flow is desired, remove Material Baffle. However, it is recommended that the Material Baffle remain in place if using bulk salt.• It is important that the Inverted Vee not be removed except when servicing.• If there are any problems while operating the spreader, refer to Troubleshooting Guide.Spreading Tips• Spread ice melters with the storm to prevent unmanageable levels of ice.• Never exceed 10 m.p.h. when spreading.• For a wider pass, increase spinner speed.• For a heavier pass, drive slower or increase auger speed.• Never operate spreader near pedestrians.• Calculate spread pattern when near vegetation.Auto-Reverse “AR” Function• If your controller displays “OL” this could indicate a jammed auger• To engage the Auto-Reverse “AR” function:Step1: Shut off Main Power Switch for 3 seconds.S tep2: Turn the Main Power Switch On. When the machine starts to back up the “AR” sequence will automatically start and the auger will reverse for several rotations to clear the jam.• After a pause of several moments, the auger will automatically return to correct rotation.• If the jam is still not cleared, the controller will again display “OL” code.• You may repeat Steps 1 & 2 for a second and third time.• If after the third attempt the controller displays “OL” code, you Must extract the material that is causing the problem.• Follow all Warning directions when clearing jams.Spreader MaintenanceModel # SP-3000/SP-6000Spreader Maintenance• Warning – When servicing is necessary, perform it in a protected area Do not use power tools in rain or snow because of danger of electrical shock or injury. Keep area well lighted. Use proper tools. Keep the area of service clean to help avoid accidents.• Warning: Never remove spreader with material in hopper.• Warning: Disconnect electricity to spreader before servicing.• Caution: – When replacing parts use only original manufacturer”s parts. Failure to do so will void warranty.• Caution: – The controller is a solid state electronic unit and is not serviceable. Any attempt to service will void warranty.• Caution: - There are no serviceable parts in the motor/transmission assembly. Any attempt to service will void warranty.• Caution: - Spinner motor is not designed for continuous duty. Allow motor to cool between long cycle times.• Caution: – When pressure washing motor enclosure area, stay at least 36’’ away from motor enclosures.• attention: Store control in cool dry place during the off season.• Use dielectric grease on all electrical connections to prevent corrosion at the beginning and end of the season and each time power plugs are disconnected.• Wash unit after each use to prevent material build-up and corrosion.• Paint or oil all bare metal surfaces at the end of the season.• Apply small amount of light oil to latches as needed.• If motor cover is removed for any reason, use silicone sealant to ensure weather proofing of enclosure.• After first use, tighten all nuts and bolts on spreader and mount.• Grease Bearings after every 20 hours of use.General Wiring InstructionsModel # SP-3000/SP-6000step 1: Take harness assembly and route from the rear of the vehicle to the front. Route harness along frame and attach to frame holes and frame supports. It is not recommended to attach to fuel or brake lines for obvious reasons. Do not route close to exhaust system or engine, even though Snowex uses high temperature wiring, it still could melt under extreme heat and short the spreader electrical system, as well as the vehicle electrical system.step 2: Mount rear plug on bumper using supplied bolts, locate towards the center of the bumper to reduce the amount of debris the tires will throw to the rear. Important: Apply a small amount of dielectric grease to the plug. Also try to mount so plug faces upward to help keep plugs tightly sealed.Step 3: Secure harness from the rear to the front using heavy duty ty-wraps or frame clips along the frame and lighter duty ty-wraps everywhere else.step 4: Layout harness portion that connects to the battery along the re wall and fender well. Do not connect power leads to battery yet. Drilla 3/4” hole in the fire wall, or use existing access hole, for the control portion of the harness and route connector and harness through hole.Be sure to check the area on the other side of the fire wall to make sure you are not going to dri ll into the vehicle harness or a control module. Generally you can drill on either side of the steering wheel for a good location.step 5: Connect harness to the back of the controller and mount to a suitable location. NOTE: You may want to contact customer before mounting controller, some prefer not to have holes drilled into the dashboard. Ty-wrap loose controller harness and move to the engine compartment. Do not mount close to any heater vents.step 6: Connect power leads to the battery: Red + Positive, Black – Negative, always connect to the primary battery if using a dual battery system, secure loose loom to any other large or medium vehicle harness with medium duty ty-wraps; this will secure wiring harness.step 7: Push the ON/OFF button on the controller to check for power, when that has been conrmed turn power OFF. The electrical portion of the installation is complete.note: If adding an inline fuse use a 60 amp slow blow (time delay) or a 60 amp relay.Harness DiagramModel # SP-3000/SP-6000CircuitCircuitMold CapNegative -Positive +D6322 Vehicle HarnessD6341 Control Power CableHarness DiagramModel # SP-3000/SP-6000D6511 Spreader HarnessViewViewCenter High Mount Stop Lamp (CHMSL)Model # SP-6000 Only• With spreader mounted on vehicle, plug vehicle (CHMSL) harness into spreader stop lamp harness.• U sing supplied harness clamps and screws, route harness along side wall lower corner or so that harness will be out of the way when spreader is in use.• L ocate vehicle ground wire and stop lamp power wire at rear of vehicle. Use supplied wire taps to connect harness to vehicle electrical system. Once wire taps are installed check to make sure stop lamp works when brake pedal is pressed. Properly complete installation by tying up any loose wires with ty-wraps, also add electrical tape over both connections to insure a solid electrical connection. Some newer trucks have auxiliary stop lamp power leads already at the rear for these types of applications.CHMSL circuit.Electrical RoutingModel # SP-3000-SP-6000CHMSLSpinnerMain InputAuger and Vibrator (not supplied on drawing)Mounting InstructionsModel # SP-3000/ SP-6000step 1: remove tailgate from pickup bed.step 2: load spreader onto truck bed and mount spinner assembly.step 3: s lide spreader forward until deector/chute assembly makes contact with vehicle. then, slide spreader back approx. 1” to allow proper clearance.step 4: i nstall stop bars using supplied hole patterns (see fig.2). to achieve the best position, you may need to drill additional holes in bracket in order to properly position spreader.step 5: n ow that the spreader is positioned front to back, you will now center it left to right. looking at the inside front and rear corner of the lower frame area, you will notice (4) holes in the bottom of the frame. using a paint pen or similar marking device, mark hole locations.step 6: b efore drilling holes, look beneath the approximate area where each hole will be located. make sure there are no vehicle components that will be in the path of the drill before doing this step. if there are interferences, you can relocate holes, making sure there are at least two forward and two rearward of the front to back centerline.step 7: install and tighten all (4) bolts.step 8: i nstall ratchet straps (see Vee pro 3000/6000 mounting system: strapping techniques). it is very important for everyone’s safety this strapping method be used as the standard mounting procedure. (do not use ratchet straps exclusively.)step 9: Connect the spreader power cord to vehicle main power plug mounted at rear of vehicle (see electrical installation).step 10: C onnect Center high mount stop lamp (Chmsl) cord from the spreader to mating half attached to vehicle (see electrical installation).TroubleshootingModel # SP-3000/SP-6000Snowex Diagnostic Test Kit (STK-080) Is Available To Accurately Diagnose Any Issues With Snowex Spreaders.Call Your Dealer For Details.Troubleshooting Material FlowModel # SP-3000/SP-6000Snowex Diagnostic Test Kit (STK-080) Is Available To Accurately Diagnose Any Issues With Snowex Spreaders.Call Your Dealer For Details.WarrantyLimited WarrantySnowex products are warranted for a period of two years from the date of purchase against defects in material or workmanship under normal use and service, subject to limitations detailed below. Warranty period of two years begins on the date of purchase by the original retail user. The WARRANTY REGISTRATION CARD must be returned to the manufacturer for this warranty to become e ective. This warranty applies to the original retail purchaser only. This warranty does not cover damages caused by improper installation, misuse, lack of proper maintenance, alterations or repairs made by anyone other than authorized Snowex dealers or Snowex personnel. Due to the corrosive properties of the materials dispensed by spreaders, Trynex does not warrant against damage caused by corrosion. Warranty claims by the user must be made to the dealer from where the product was purchased, unless otherwise authorized by Snowex. Snowex reserves the right to determine if any part is defective and to repair or replace such parts as it elects. This warranty does not cover shipping costs of defective parts to or from the dealer.LIMITATION OF LIABILITYNeither Snowex, nor any company a liated with it, makes any warranties, representations for promise as to the performance or quality other than what is herein contained. The liability of Snowex to the purchaser for damages arising out of the manufacture, sale, delivery, use or resale of this spreader shall be limited to and shall not exceed the costs of repair or replacement of defective parts. Snowex shall not be liable for loss of use, inconvenience or any other incidental, indirect or consequential damages, so the above limitations on incidental or consequential damages may not apply to you.NO DEALER HAS AUTHORITY TO MAKE ANY REPRESENTATION OR PROMISE ON BEHALF OF SNOWEX, OR TO ALTER OR MODIFY THE TERMS OR LIMITATIONS OF THIS WARRANTY IN ANY WAY.SP-6000Drive Assembly Parts Breakdown Model # SP-3000/SP-6000Drive Assembly Parts BreakdownModel # SP-3000/SP-6000Complete Drive AssemblyD6565Auger Assembly Parts Breakdown Model # SP-3000/SP-6000Auger Assembly Parts Breakdown Model # SP-3000/SP-6000NotesNotes31© Trynex International 2011 (REV 001)。
Honda HS1336i 雪扔机说明书

his powerful machine blends superior capabilities,advanced engineering and hybrid technology to clear snow in the most demanding commercial and residential scenarios.Honda’s Hybrid Technology:Better Throw, Smoother Go.The Honda HS1336i runs smarter and smoother thanks to the innovative use of hybrid technology. We’ve combined the engine and electric motor power to provide powerful snow throwing and uninterrupted travel and motion simultaneously. While engine power expels snow rapidly, dual electric motors deliver smooth and consistent power to the Honda track drive system.Ideal for:• L arge properties in areas prone to heavy snow• M unicipalities and public spaces• A cademic institutions • R etail and event venues • H otel andresort facilities• R esidential communities, particularly those with expansive, hilly conditionsIntroducing The UltimateWhen it comes to your extreme snowblowing needs, we’ve thought of everything. Peruse each essential detail to discover how the HS1336i is the dream machine you’ve been looking for.Fully electric auger housing: With electric movement powered by two motors, the HS1336i’s auger housing not only tilts up and down but rotates as well. This allows you to tackle hilly grades without compromising the balance of the snowblower , for more complete, efficient and safer performance.Engine and electric power combined: The iGX engine drives the auger and fan, effectively blowing snow , while an on-board alternator powers twin electric track drive motors.Electric starting: The 24v DC electric starting system employs two heavy- duty batteries as its power source. This is a clean, no hassle solution for starting the engine.Operator essentials kept handy: Just under the control panel, a large box holds the operator’s manual and tools for easy access and simple storage.Smart solutions for snow discharge: A fan, strategically placed behind the serrated augers, ensures snow discharge is expelled ahead of the augers to eliminate clogging and potential for back-up. Likewise, the discharge shoot is double-articulating with two hinge points for more accurate snow tossing trajectories.Electric clutch for auger engagement: Engage the auger and fan with just a fingertip thanks to the electric-powered clutch, a nice advancement from the traditional handlebar system that requires more manual effort.On-board diagnostics: Keep track of all operational details through the handy on-board diagnostics panel.Convenient electric transport mode: With the electric transport mode, you can move the unit without starting the engine—great for relocating from the garage or storage unit to work areas.Electronic IndicatorsQuick view indicators and diagnosticstrack vital information to monitor alloperating systems.Heavy-Duty, Serrated AugersIce-breaking augers automatically liftin reverse when Automatic orSemi-Automatic modes are engaged.Standard Work LightThe well positioned light illuminateswork paths in dark conditions.For optimum performance and safety we recommend you read the owner’s manual before operating your Honda Power Equipment. Specifications subject to change without notice.All images contained herein are either owned by American Honda Motor Co., Inc., or used under a valid license. It is a violation of federal law to reproduce these images without express written permission from American Honda Motor Co., Inc., or the individual copyright owner of such images. All rights reserved. HONDA, the HONDA POWER EQUIPMENT logo, Honda snowblower model names and their trade dress are trademarks of Honda Motor Co., Ltd. used under license by American Honda Motor Co., Inc. Many Honda engine, snowblower and power equipment model names,and associated trade dress may be seen at . ©2013 American Honda Motor Co., Inc. C0492Rev . 01Visit us at *Gasoline, engine oil, transmission oil, and battery fluid not included.。
爱尔士水炼器维护指南说明书

• The system will not be able to deliver Product Water while the system is being sanitized.
3/9
How to Sanitize the System (Direct-Q systems only), Continued
Sanitizing the System and the Tank
(continued)
Step
Action
The system will now go into FILLING TANK mode. Let the tank fill up to the 100% level.
o
• You will need 200 ml of 30% Hydrogen Peroxide solution and 200 ml of
purified water. Millipore does not sell Hydrogen Peroxide but it is readily available through most Scientific Supply Companies.
The total time needed to sanitize the system is at least 4.5 hours.
• If you have performed a system sanitization, then you do not need to perform a tank sanitization.
Esposlo White Eagle Digit 产品说明书

98050062 98050061
98050060
06200008 07300092
* SPECIFICARE VERSIONE SPECIFICY VERSION
TAV 03
COMPONENTI RUBINETTI VAPORE E ACQUA CALDA
COMPONENTS OF STEAM AND HOT WATER TAPS
00000118
07300166 பைடு நூலகம்2280012
06200089
00000197
40200004
07300183.5 (H=5mm) 07300183.3 (H=3mm) OPTZ
02280033 03000066 00000221 00000217 06200081
98030913 GRUPPO BASSO LOW GROUP 98030914 GRUPPO BASSO LOW GROUP
01000086 04600020
04000051
11600001.W
11600001.W 05000015
07300692
04900780
98030929
02280011
07300392 02280037 08000027 07300293 07300295
02280004
04100072 00300002 07300720
04000380
03003458
8
00000026 00000026 03003462
03003425
00000122
03003410 06100140*
14100044
14100043
00000196 00000073 00300024
- 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。
hs白雪崩能天使说明书修正版
一、产品概述:
HS白雪崩能天使是一种新一代的高性能能量饮料,旨在提供持久的能量和清爽的口感,为体力和脑力消耗大的人群提供补充。
本说明书旨在帮助用户了解产品的成分、功效以及使用方法等信息。
二、产品成分:
1.水:经过精细处理的纯净水,确保产品的安全和卫生。
2.咖啡因:适量咖啡因含量,提供快速且持久的能量供应,提高警觉性。
3.维生素B群:能够提供营养物质,促进新陈代谢和能量产生。
4.矿物质:包括钠、钾等重要的电解质,帮助维持身体正常功能。
5.糖分:适量的糖分提供即时的能量,并帮助产品的口感更加顺滑。
三、产品功效:
1.提供持久的能量:HS白雪崩能天使含有适量的咖啡因和糖分,能够提供快速和持久的能量供应,增加体力和耐力。
2.提高警觉性:咖啡因能够促进神经系统的活动,提高警觉性和集中注意力的能力,帮助应对疲劳和压力。
3.补充营养物质:维生素B群和矿物质的添加,能够为身体提供必要的营养物质,促进新陈代谢和能量产生。
4.提供清爽的口感:HS白雪崩能天使具有清爽的口感,通过适度的
碳酸化和口感调节,增加饮用时的满足感。
四、产品使用方法:
1.开封前请摇匀:在饮用前,将瓶子摇匀,确保产品中的成分均匀分布。
2.适度饮用:每次饮用量请根据个人需求和体重而定。
初次使用时,
请尝试较小的饮用量,以确定个人的耐受能力。
3.饮用时间:适合在感到疲劳、需要持续提神或进行高强度活动时饮用,不宜过度依赖。
4.请勿过量饮用:建议每天不超过2瓶,以免对身体健康产生不利影响。
五、产品注意事项:
1.儿童禁用:本产品适合成年人饮用,对于儿童和孕妇来说不适合。
3.运动前慎用:在进行高强度运动前,注意饮用时间间隔,以免影响
个人体感和运动能力。
4.存放要求:请存放在阴凉干燥处,避免阳光直射以及高温、高湿度
的环境。
5.因个体差异可能产生的效果:产品的功效会因个体差异而有所不同,具体效果请根据个体情况进行判断。
六、产品包装规格:每瓶HS白雪崩能天使容量为500毫升。
总结:
HS白雪崩能天使是一款提供持久能量和清爽口感的高性能能量饮料。
它包含适量的咖啡因和糖分,能够提供快速且持久的能量供应。
另外,添
加了维生素B群和矿物质,能够为身体提供必要的营养物质。
饮用时请摇匀,适度饮用,并在儿童和孕妇身上禁用。
存放时避免阳光直射和高温、
高湿度环境。
每瓶容量为500毫升。
请根据个人情况合理饮用,以确保健
康和效果。