注塑及模具英文

Hopper Dryer 料斗干燥器Injection Molding Cycle 注塑周期Crushing Mill 粉砕机Precision Injection 精密成形Gas Injection / AGI 吹气成形、气辅成形Set the condition 设定注塑前提Machine 机械Mold Set-Up 上模Screw 螺杆、螺钉、螺旋Mold Down 下模Screw Head 螺杆头Pressure 压力Joint 接头、接缝Low Pressure 低压Injection 注塑Low Pressure Clamping 低压锁模Feeder 送料（加料）器Holding Time 保压时间Compound 混炼料；Back Pressure 背压Blend 搅混、调合Clamping Force合模力Mixer 混淆器Hold Clamping pressure 锁模型压成力Mixing 混淆Clamping Stroke 合模行程Cooling 冷却Clamping Unit 锁模装配Cooling Tower 冷却塔Mold Opening 开模Chiller冷水机Mold Closing 合模Temperature Controller 温调机Speed 速率Cylinder 料筒Injection Speed 射出速率Heater 加热器Injection Capacity 注塑量Band Heater 加热圈Charging 计量Thermocouple 热电偶Charging Stroke 计量行程Nozzle 射嘴Rib 骨位、筋位、增强筋Nozzle Head 射嘴头子Insert 嵌件、镶嵌Tie Bar 、Tie rod 拉杆、拉杠Wall Thickness 胶厚、壁厚Distance Between Tie rods 拉杆距离Plasticizing 塑化Limit Switch 限位（限定）开关Thermal Decomposition 热分化Operation Switch 操作开关Shrinkage収缩Operation Guide 操作指南Resin 树胶Control Panel 节制器Material 原料、质料Automatic 全自己主动Plastics 份子化合物塑料、塑胶成品Semi Auto 半自己主动Rubber 橡胶Hand 手动Master Batch 色母Handle 手柄Powder 色粉、粉、粉末Extruder 押出机、挤塑机Dry Color 色粉、干色料Extrusion Molding 挤塑Pellet 粒、塑胶粒Blow Molding Machine 吹塑机Glass Fiber, Fibrous Glass 玻璃纤维Blow Molding 吹塑Hose 软管、管Program Control 步伐节制Over Packing 过充填Process 工艺、工序、历程MoldMark 马克模伤、模痕Inject visor 注塑工艺步伐节制装配Shock 冲击、冲击Damage 损坏、毁伤Cold Slug 冷料Sink 马克抽水、紧缩Cold Slug Well 冷料井Short Shot 充填不足、欠料Freeze 冷凝Flash 毛刺、披峰Hydraulic 液压、油压String Flash 胶丝Hydraulic Ejector 液压顶出、液压脱模White 马克白化、顶白Hydraulic Pump 液压泵Silver 雪白、银痕Hydraulic 摩托液压电动机Flow mark 流纹Air Compressor 空器压缩机、空压机Burn 烧黑、烧焦Oil Leakage 漏油异物Black Spot 异物、黑点Oil tank 油箱、油槽Sticking 粘模Piston 活塞Weld 溶接线、联合线Air Cylinder 气缸Flash 料花Alarm 报警Oil 马克油污、油渍Safety Gate 太平门Damage 打痕、击伤Emergency Stop 紧迫遏制Cracking 裂、开裂Color Change 换色Jetting 气纹Purge Material 清机份子化合物塑料Deform 变型Resin Thermal 胶料温度Warping 屈曲、翘曲、外倾Mold Thermal 模温Bend 屈曲Heat Up 升温、升热Torsion 扭曲Air Shot 空射胶、空打Uneven Color 色彩不匀称Try 试模Eccentric Wall Thickness 壁厚不匀称Mold Release 脱模Bladder、Cell 气泡儿、浮泛、空地Mold Release Agent 脱模剂Stripes 条纹Rust Preventatives 防锈剂Dirty 污痕、污点、渗溢Can’t Release （产物）没有办法脱模Flaking 脱落、剥落Shot 注、射、啤Tear Off 上下翻动Gate 进点，浇口Float 浮起Center Gate 中间浇口Screw Damage 螺钉滑牙Sprue Runner 水口，注口、流道料Shortage 员数不足、欠品Clearance 距离、余隔Run out 跃动度、偏疼Sprue 主流道注（塑）口Contraction 紧缩Runner 流道、流道料Assembly NG 嵌合不良、装配不良Air Vent 散气眼、透风口Stress 应力Breathing 排气、散气Internal Stress 内部策应力Anneal 热措置惩罚、退火Preparation 摆设、筹办Mold 生产模型Stopper 挡块Machining Center 加工中间Stripper 推板、脱模型板Universal Milling Machine 刨床、锣床Spacer Plate 垫板Latter 车床Mould Base 模胚Surface Grinder 最简单的面磨制机床Support Plate 托板Grinding Drilling 钻床Support Pillar 撑头Electric Discharge Machine 火花机加工Puller Lock 拉塞Wire EDM 线割切Puller Bolt 拉杆Nitride Steel 氮化钢取付板Top clamp Plate 工字板、水口板Nitrogen 氮气Bottom Plate 底板Nitride 氮化措置惩罚Return回针Titanium 钛Guider Pin 导柱Heat Treatment 热措置惩罚Guider Bush 导套Hardening 淬火Die 生产模型、动模、移动模型板Temper 回火Die Plate 模型板、载模型板Annealing 退火Module 板块、模件、模数Pre harden 预加硬钢Parts 零件、生产模型零件Hardness 硬度Eye Bolt 吊环螺栓Soft 软、软的Crane 吊车、吊车、行车Electrodes 铜公Hook 勾、吊勾Insert 镶件Wire 钢丝、钢丝绳Slide 行位、滑块File 锉子Taper 斜度Oil Stone 油石Taper 斜度、锥度、锥形的Sand Paper 砂纸Draft 脱模斜度Mesh 节号、目Guide Pin 导向柱刻印Engrave 刻印Sleeve Pin 司筒针Texture 蚀纹Square Pin 扁顶针放电目EDM Texture 火斑纹Angular Ejector 斜顶针Rough 粗的Cavity 模腔、前模、母模Trifling 细的、幼的Core 模心、后模、公模Diamond Cut 钻石纹Number of Cavities 取数、模腔数Roulette 滚花刀、刻痕Rocket Ring 定位环Blast 喷沙O Ring O环；胶圈Hot Runner 暖流道Wall Thickness 肉厚、胶厚Repair 补缀Add Material 加胶接Welding 溶接、焊接Building 加胶溶接机Welder 焊机、电焊机Cut Material 减胶溶接棒Welding Rod 焊条、电焊条Modify the tooling 改模（因设变补缀）Argon Arc Welder 氩弧焊Repairing the tooling 生产模型补缀Torch Bumper 喷燃烧现象器、火苗燃烧现象器Design 预设Ejector Pin 顶出Design Drawing 预设图Ejector Pin 顶针Design Change 预设变动、设变Gate Type 水口体式格局Designer 预设者、预设职员Tunnel Gate 隧道式浇口、潜入水下口Designer 预设者Pin Point Gate 针孔形浇口、细水口Mold Design 生产模型预设Side Gate 侧水口、洪流口Mold Specification 生产模型建造仕样书Direct Gate 直接浇口Specification 规格Multi Gate 复式浇口Mold Construction 生产模型机关、生产模型布局Fan Gate 扇形浇口Input 输入Film Gate 扇形浇口Programming 编程Jump Gate 搭接浇口3D Drawing 3D图、3维图Gate Balance 浇口均衡2D Drawing 2D图、最简单的面图Undercut 凹槽、倒扣Front Elevation 正面图Cooling Line 水管、运水Plan 平面图Cross-sectional Drawing 剖面图Cooling 冷却回路、运水CAD Date CAD 数值Modeling 模Mock-up 模子、原尺寸模子Software 软体Hand Made Sample 手板、手工样品Mold Drawing 生产模型图Module 模数、模量；模件Part Drawing 零件图Gear 齿轮；传动装配Diagrammatic Sketch 草图Helical Gear 螺旋齿轮Drawing 绘图Solid 群体的；固体Revised Drawing 图订変换Transformation 变换、转换Dimensioning 记入尺寸Floppy Disk 磁盘、软盘Out Mold Direction 出模标的目的Computer 台式机、计较机Draft 出模斜度Personal Computer 私家用电器脑、手提台式机Pitch 间距；齿距Version 情势、品类（译文，翻译，译本）Angle 角度Reading 读取Projected Area 投影平面或者物体表面的大Readout 读出Taper 锥度；斜度Reading 读数Under cut 倒扣圧缩Compression 压缩2 Plate 两板模开Open 打开；读出文件（软体）3 Plate 三板模Not Open 打（解）不开、读不出Offset 偏置、偏移Miss 纰缪、掉误Mold Layout 分模Condition of the progress 进程项度状态Split Mold 对于开式生产模型Finishing 打光、磨光Slide Core 滑动模芯Polish 研磨、打磨Loose Core 勾当模芯Target 方针、目的、对于准Loose Mold 勾当生产模型Schedule 每一日安排表Press 冲压、压床、压Maintenance 维护、调养Press Machine 冲床Did Casting 压铸Progressive 级进Sintering 加热使黏结Single 单冲Monkey 勾当板子Packing Plate 垫板Clamp 夹具（固定生产模型用）Punch 冲头、凸模、冲床Scrap 废铁；废物、废渣Punch Press 冲孔机Rust 生锈Die 下模Rust Inhibitor 防锈剂Die Set 模座、模架Washing Agent 洗濯剂Press Mold 冲压模、五金模Ultrasonic Cleaning 超音波洗濯Leveler 整平滚；矫平机Feeder 送料机；加料机Burr 反边、毛刺Drawing 拉伸Thinner 天纳水；淡薄剂Burring 去毛刺Triclinic 三氯乙烯脱脂剂Blank 复合Trivalent Chromium 六价铬Cutting] 落料、冲孔Bending 折弯Degreasing 脱脂、去油Bend 折弯、屈曲Harmful Metal 有害物Box-Bending 箱Cut 割切L-Bending L拆弯Press；Sheet Metal 板金V-Bending V折弯Cut 堵截、割断Punching 冲孔、钻孔Iron Plate 铁板SECC 镀锌板Cutting 冲压、抽去Silver Top 镀锌板Shirk 避空Stainless 不锈钢Calking 铆接Copper 铜Tap 螺丝攻Brass 黄铜Dies 板牙Steel 钢Reamer 铰孔Aluminum 铝Reamer 铰刀；扩孔器Width 宽度End Mill 刨刀板厚Thickness 板厚Grinder 砂轮儿机、磨制机床Density 疏密程度Barrel 滚筒Coil 卷材Barrel Tumbling 滚（桶抛）光Width Cut 片材Plating 电镀Nut 螺丝帽、螺帽Electro plating Vacuum真空电镀Bolt 螺栓、螺杆Spot Welding 点溶接、点焊Chrome plating 镀铬Jip 夹具，治具Galvanization 镀锌Clearance 间隙Shave 切、削Matching 接口Assembly 装配、组装Counter 统计器Assembly Unit 装配组件Count Method 统计法Assembly Time 装配工数Timer 按时器Line 出产线、拉线Digital 数码（的）、数码Self 单人装配Digital Camera 数码拍照机Conveyer 传送带Connect 插座、插嘴U Line U形出产线Plug 插头、瓶塞Capacitor 电器皿Lamp 灯Resistor 电阻器Lighting 点灯、灯亮Diode 二极管Fuse 断电丝LED (light-emitting diode) 闪光二极管Power Code 电源线Transistor 形成晶体体管Wire Hamess 电线导线IC集成电路Bar Code 条纹码LCD (liquid crystal display) 液态晶体预示器Vinyl Tape 绝缘带Sensor 传感器Noise 异音、杂音、噪音Relay 替续器Decibel 分贝（声强单元）Connector 保持器Instruction Sheet 功课引导书Transformer 变压器Access Platform 功课台Breaker 断路器Series 串联Buzzer 蜂鸣器Parallel 并联Printed Circuit Board /PCB 印刷电路板Clutch 连轴器、聚散器Driver 螺钉刀、起子Solenoid Coil 电磁线圈Driver 十字批（起）Coil 线圈Driver 一字批（起）Static Electricity 静电Electric Driver 电动螺钉刀、电批Prevent Electricity 防静电Torque 扭矩、转矩Fan Motor 电扇电动机Screw 螺钉Grease 润滑Washer 垫圈（片）Apply 涂油E-Ring 卡环Block Copy 底板、草图Solder 焊锡Film 胶卷、软片Soldering iron 烙铁Silk Print 丝印Tin 锡Pat Print 移印Earth 接地、地线Hot Stamp 烫印Alcohol 火酒、乙醇Ink 印字油墨Foot Switch 脚踏开关Color Sample 色板Terminal 端子印刷不良Print NG 印刷不良Terminal Block 端子板Bleeding 渗溢、飞油Label 标贴、标签Stamp 捺印Bar Code 条纹码、条形码Spray 涂装、喷涂Mile 软片；聚酯树胶Wood Graining 木纹加工Quality Control 品位办理Sample 样品、样本、样板Inspection 查抄Boundary Sample 限度样板I Q C 验收、受入查抄Approval Sample 认可样板O Q C 出货查抄Tolerance 公役P Q C 工程查抄Plus 正、加号Sampling 抽查Minus 负、减号Total Inspection 全检Disperse 不不变、颠簸Visual Inspection 目视查抄不稳固Unstable 不不变Appearance Check 外不雅查抄Balance 均衡、均衡Patrol 巡检工程能力Process Capability/CP 工程能力Measurement 丈量仪三角螺丝刀Detection 检验测定Measurement 丈量、标定Check Point 查验（重）点Measuring Method 丈量要领No Check 漏检Clogging 刻度、分度特采声请Special Adoption Application 特采声请Memory 储存、影象暂定対策Provisional Countermeasure 暂定对于策Three-Dimensional Measuring Machine 3D丈量仪长久対策Permanent Countermeasure 长久对于策Microscope 东西目镜Claim 投诉、报怨、索赔Profile Projector 投影机Appraisal 评价Slide Calipers 卡尺Decide 鉴定Micrometer 量具検査基准Check Standard 查抄基准Lever Type Dial Test 百分表検査基准表Inspection Sheet 查抄基准表Torque Gauge 扭转力计QC工程表QC Flow Chart QC工程表Scale 刻度尺Specula Face 镜面Square 90度角尺Mirror Face 光面、光泽面Steel Tate 皮尺Texture Face 蚀纹面Height Gauge 高度尺First the face 一级面Pin Gauge 柱规Appearance 外不雅面Thickness Gauge 片Appearance Part 外不雅产物Protractor 角度仪Function Part 性能部品Tension Gauge 拉力计Slide 滑动面Indicator 百分表Flatness 最简单的面度Hardness Tester 硬度计Reform 矫正Multitester 万用表Check Jig 查抄用治具Surface Plate 平台、平板Feed Back 反馈V Block V形块Communication 信息、报怨Gauge Block 方块规Manual 指南、手册Dial Gauge 百分表、百分表Flow Chart 流程图Data 数值Process Inspection 工程监查Data Sheet 数值单Qualification 确定地认为Parameter 参量Graph 图表、曲线图Warehouse 堆Customhouse 海关Pallet 卡板Customs Clearance 报关、通关Corrugated Fiberboard 纸箱Customs Clearance 报关手续Partition 刀卡Electronic DataInterchange 电子报关Recycle Box 周转箱Container 货柜车Plastics Box 折叠式周转箱Foot 英尺Container 份子化合物塑料周转箱Packing List 装箱单Poly-bag 胶袋List 详细登记单Tape 封箱品牌一字螺丝刀胶纸Declaration 申请报告Rope 绳索、线Import 入口First in First out 先入先出Export 出口Fork Lift 铲车Fumigation Certificate 薰蒸证实书Hand Lift 手推铲车No Wood Packing Certificate 无木质包装证实书Bogie 台车Wooden box 木箱Truck 卡车Shelf 货架License 批文、容许Stock 在库数License Document 转厂Shelf 盘货Limits 指标、配额指标Dead Stock 死仓储、积压品Import Limits 入口指标Purchasing 采集购买Unbalance 数目不服衡Supply Parts 支给品合约Contract 合约Purchase Parts 采集购买品Contract 手册Lead Time 交货期、定货期Order Placement 发定单Transfer; Carry Over 转余料、拔余料Pay 有偿Erase 核消Free of Charge 没有报酬的Provision of Information 加签Vender 供应商Submit Document 递单Quotation 报价单Brand Name 商物品名称称Invoice 发票、请款单Goods No 商品编码Deposit 预付款、包管金Foreign Enterprise 外资企业Payment 付款Owned Enterprise 独资企业Payment Condition 付款Partnership Enterprise 合资工厂Month Payment 月结Processing 来料加工Over Time 加班（没事了事情日加班）Bailment Processing 委托加工Over Time Fee 加班费Labor Cost 人件费Holiday Work 加班（节沐日上班）Amortization 折旧费Two shift 两班制Hour Charge 加工费；工时费Day Shift 白班Exchange Rate 汇价Night Shift 晚班Material Certificate 质料证实书。