N Type connector series
MWTC无线智能连接器系列说明书
Miniature Wireless Thermocouple ConnectorsU Available in J, K, T , E, R, S, B, C, and N Thermocouple CalibrationsU Built-In Cold Junction Compensation and LinearizationU Records 65,400 Process Temperature Data Points or 32,700 Process and Ambient Temperature Data Points U Records at Power-Up, or at a Pre-Determined Time and Date U Transmits Process and AmbientTemperatures, and Battery Information Wirelessly to MWTC-REC Receivers U Free Application Software Converts Your PC Into a Multi-Channel Chart Recorder or Data LoggerThe new MWTC wireless Smart Connector series features a compact, battery powered thermocouple connector that can transmit and/or record temperature data back to a mating receiver up to 90 m (300') away. During the initial set-up, the connector can be set to transmit, transmit and record, or record only at a pre-set time interval. The recording can begin either at power up, or at a pre-set time and date. Multiple wireless connectors (up to 48 channels) can transmit to one MWTC-REC receiver.Stored data can be easily downloaded to a PC via direct USB connection. The user can record either 65,400 process temperature data points, or 32,700 Process and ambient temperature data points.SPECIFICATIONSThermocouple Types: J, K, T, E, R, S, B, C, N (factory set)PC Interface: USB (one cable inlcuded)Modes of Operation:Transmit, transmit and record, or record only, set by softwareMemory: 65,400 process rdgs, or 32,700 process and ambient rdgs, set by softwareData Logging Start Time:At power-up or at a pre-set time and date, set by software Logging/Transmit Time Interval: 2 sec to 2 minutes, set by software Radio Frequency:ISM 915 MHz or ISM 868 MHz RF Power Output: Less than 5 mW (7 dBm)Range of RF Link:Outdoor Line of Sight: 90 m (300')Indoor/Urban: 39 m (130')Battery: AAA size, 1.5V Lithium battery (included). Also, compatible with 1.5V alkaline or 3.6V lithium batteryBattery Life (Typical): 7.2 months at 1 sample per minute at room temperatureMWTC Series* Specify calibration: J, K, T , E, R, S, B, C, or N .** Specify ISM Frequency: 915 for USA/Canada, or 868 for Europe.Note: Because of transmission frequency regulations, these products may only be used in the United States and Canada (915 MHz models) or Europe (868 MHz models).Note: Optional wireless receiver is not required to operate the data logging connectors. Stored readings can be downloaded via the USB connection. One USB cable is included with transmitter.Wireless transmitter comes complete with 1 m (40") thermocouple sensor, USB cable, mounting bracket, and one “AAA” size 1.5V Lithium battery. Wireless receiver comeswith operator’s manual and software CD.USB connectionItem shown is not actual size.For more information visit:/mwtcMWTC-REC148 Channel MWTCreceiverItems shown are not actual size.MWTC-REC5-91548 Channel MWTC receiverDAS – Networking/Wireless93。
Sophos APX 320X 操作指南说明书
Operating Instructions APX 320XForewardWe are pleased to welcome you as a new Sophos APX Series customer.Sophos APX Series access points are high performance wireless products using the latest 802.11ac Wave 2 technology for a best-in-class user experience. The APX Series models can be easily managed in Sophos Central, our cloud-based security management platform. All you need to do is set up a Sophos Central account and plug in the device anywhere in your network. The access point will find the cloud-based controller automatically and become operable within seconds.These operating instructions will help you set up your Sophos Central account, install and configure your Sophos APX Series access point and also provide detailed technical specifications. In addition, please also see the following documents that contain useful information on safety, regulatory compliance, and configuration options:ÌSophos APX Series Safety Instructions and Regulatory InformationÌSophos APX 320X Quick Start GuideThe instructions must be read carefully prior to using the device and should be kept in a safe place. You can download all user manuals and additional documentation from the Sophos Knowledgebase under /en-us/support/knowledgebase.aspx or from /get-started-ap.Security symbolsThe following symbol and its meaning appears in the Quick Start Guide, Safety Instructions and in these Operating Instructions.Caution and Important Note. If these notes are not correctly observed:ÌThis is dangerous to life and the environmentÌThe access point may be damagedÌThe functions of the access point will be no longer guaranteedÌSophos shall not be liable for damages arising from afailure to comply with the Safety InstructionsDesigned useThe access point must be installed pursuant to the current installation notes. Otherwise failure-free and safe operation cannot be guaranteed. The EU declaration of conformity is available upon request from the following address:Sophos Technology GmbHGustav-Stresemann-Ring 165189 WiesbadenGermanyOperating elements and connections N type connector for 2.4/5 GHz antenna (Radio 1)N type connector for 2.4/5 GHz antenna(Radio 0)N type connector for 2.4/5 GHz antenna (Radio 1)N type connector for 2.4/5 GHz antenna(Radio 0)Forge posts for mounting plate connection Gore vent LED RJ45 connector/Reset button Grounding wireconnectorComponent descriptionsLEDs* Your AP should recover from this state after a maximum of 5 minutes.Connection and configurationYour access point can be managed by a wireless controller located in Sophos Central. The initial connection of your access point to your network and the wireless controller is described in the APX Quick Start Guide which was shipped with your device or is available under /get-started-ap.For the access point to communicate with Sophos Central servers the following ports will need to be open on your firewall:Ì443 (HTTPS)Ì80 (HTTP)Ì123 (NTP)After successful connection you can start your initial configuration.Setting up your access point in Sophos CentralYou will need a Sophos Central account to manage your access points from Sophos Central. Please go to https:// to sign in under your account or create a new account.After signing in select Wireless from the popup screen or click on Wireless in the left navigation to get started.Follow the Onboarding Wizard to register your access point.For more information, please see the Sophos Central Admin Help.Setting up your access point in XG FirewallPlease note: APX 320X is not supported on XG or XGS Firewalls.Reboot and resetYour access point can be rebooted with the installed configuration or reset to the factory default configuration depending on how long you press and hold the reset button. Reboot with current image and configuration1. Press reset button.2. Release reset button.3. AP reboots (LED will go off, then will turn to solid green).Reboot with current image and clear configuration1. Press and hold reset button.2. AP reboots (LED will go off and then switch to green briefly).3. LED will turn solid red for 5 sec. You can still cancel the configuration clearanceprocess by releasing the reset button before the LED starts blinking.4. LED will blink red (configuration will be cleared).5. Release reset button.6. AP reboots with factory default settings.Technical specifications* Not available in the countries listed here: https:///support/s/article/KB-000039850 ** For the countries listed here: https:///support/s/article/KB-000039850Radiation patterns2.4 GHz BandH-plane V-plane—2400 (MHz) —2450 (MHz) —2500 (MHz)5 GHz BandH-plane V-plane—4900 (MHz) —5150 (MHz) —5350 (MHz)—5475 (MHz)—5725 (MHz)—5875 (MHz)Optional Sector / Directional AntennasTechnical specifications120° Sector AntennaFrequency range2400~2500 MHz5150~5850 MHzPort V-pol. / H-pol.V-pol. / H-pol.Antenna Gain10.6~10.8 dBi) / 10.0~11.4 dBi 12.5~13.1 dBi / 11.6~12.9 dBi HPBW / Horizontal76~77 deg / 63~66 deg40~61 deg / 52~76 deg HPBW / Vertical24~25 deg / 26~28 deg11~13 deg / 11~13 deg Isolation20 dBImpedance50 OhmsConnector N JackDimensions320 x 200 x 20.5 mm (12.6 x 7.87 x 0.81 inches)(Height x Width x Depth)30° Directional AntennaFrequency range2400~2500 MHz5150~5850 MHzPort V-pol. / H-pol.V-pol. / H-pol.Antenna Gain11.6~11.8 dBi) / 11.6~12.0 dBi 10.6~11.0 dBi / 10.4~11.5 dBi HPBW / Horizontal36~37 deg / 35~36 deg33~35 deg / 26~36 deg HPBW / Vertical34~35 deg / 36~38 deg32~39 deg / 30~41 deg Isolation20 dBImpedance50 OhmsConnector N JackDimensions320 x 200 x 20.5 mm (12.6 x 7.87 x 0.81 inches)(Height x Width x Depth)Radiation patterns Sector Antenna – Horizontal Polarization 2.4 GHz BandH-plane V-plane—2400 (MHz) —2450 (MHz) —2500 (MHz)5 GHz BandH-plane V-plane—4900 (MHz) —5150 (MHz) —5350 (MHz)—5475 (MHz)—5725 (MHz)—5875 (MHz)Radiation patterns Sector Antenna – Vertical Polarization 2.4 GHz BandH-plane V-plane—2400 (MHz) —2450 (MHz) —2500 (MHz)5 GHz BandH-plane V-plane—4900 (MHz) —5150 (MHz) —5350 (MHz)—5475 (MHz)—5725 (MHz)—5875 (MHz)H-plane V-plane—2400 (MHz) —2450 (MHz) —2500 (MHz)5 GHz BandH-plane V-plane—4900 (MHz) —5150 (MHz) —5350 (MHz)—5475 (MHz)—5725 (MHz)—5875 (MHz)H-plane V-plane—2400 (MHz) —2450 (MHz) —2500 (MHz)5 GHz BandH-plane V-plane—4900 (MHz) —5150 (MHz) —5350 (MHz)—5475 (MHz)—5725 (MHz)—5875 (MHz)Mounting instructionsThere are various mounting options available allowing you to hang your access point on the wall or mount it on a pole. Both options require the use of the mounting bracket which is shipped with your access point. The following sections provide detailed instructions on each of these options.Mounting bracketMounting holesVertical orientation mounting clamp slots Horizontal orientation mounting clamp slotsMountingattachment slotsMount plateattachment screwWall mount1. Use the mounting bracket to mark the screw mounting positions on the wall.2. Attach the access point to the bracket by hanging the 4 forge postsinto the attachment slots of the bracket and pressing it down.3. Tighten the attachment screw to fix the access point to the bracket.1.3.Tighten the attachment screwPole mount1. Attach the two metal clamps to the back of the mounting bracket using thevertical or horizontal mounting slots (according to the desired orientation).2. Hold the bracket against the pole and tighten the metal clamps.3. Attach the access point to the bracket by hanging the 4 forge postsinto the attachment slots of the bracket and pressing it down.4. Tighten the attachment screw to fix the access point to the bracket1. 2.3. 4.Sector / Directional Antenna Mounting Instructions1. Attach the articulating mount to the back of the Sector /Directional antenna using four of the supplied M6 nuts.2. Fix the T-form bracket to the pole by using the two supplied stainless steel hoseclamps.Please note: The clamps can be used for poles of 35-80 mm (1.5-3 inches) diameter.3. Fix the articulating mount to the T-form bracket by using thesupplied M8x40 bolts, nut, spring washer and washer.4.Direct the antenna upward or downward (max. angle is 27°) and fix it into place.1.27°27°Use a No. 12 hexagonal wrench to lock the M8 nut.4.M8x40 ScrewBoltsT-form BracketWasherSpring WasherM8 Nut3.2.Connect the Sector / Directional Antenna to the Access Point Connect the antenna to your APX 320X access point by using the supplied cables. You can use your sector/directional antenna either in combination with the standard omni-directional antennas or with another sector/ directional antenna.Choose the appropriate connection for the scenario which best fits your use case - as shown in the table below.NOTE: If you use the sector/directional antenna with the APX 320X in some countries, the use of Radio-1 may not be possible. Regulatory restrictions in some countries prohibit the use of low band 5 GHz channels which do not support DFS in outdoor environments. Therefore, Radio-1 cannot be configured when used in the countries listed here: https:// /support/s/article/KB-000039850. In those countries, this model will function as a single radio device (2.4 OR 5 GHz), your antennas should be connected to Radio-0 only, and concurrent use of the sector/directional and omni-directional antennas is not possible.a. b. c.Configure Sector / Directional Antenna Software SettingsOnce the external antenna is connected, please select the corresponding antenna settings in your Sophos Central Wireless admin account. Once selected and the configuration synched, the AP reboots and the correct power values will be set. WARNING: Failure to configure the correct antenna settings may place the AP outsideof regulatory limits. The administrator is responsible for ensuring this configuration is correct.Operating Instructions APX 320X© Copyright 2020-22. Sophos Ltd. All rights reserved.United Kingdom and Worldwide Sales Tel: +44 (0)8447 671131Email: ****************North American SalesToll Free: 1-866-866-2802Email: ******************Australia and New Zealand Sales Tel: +61 2 9409 9100Email: ****************.au Asia SalesTel: +65 62244168Email: ********************。
HDMI CM CONN规格书
创亿欣电子有限公司TRONIXIN ELECTRONICS CO.LTDHdmi c type SeriesConnectorProduct SpecificationDOC. No.:SP-HDMI CM CONN-00Rev.:APage:1/ 7Approved/Date Checked/Date Written/DateTom2012.11.15Rokie2012.11.15Kenn.lin2012.11.15Product SpecificationFor HDMI C Type Series ConnectorRev. ECR# Description Written/Date Checked/Date Approved/Date X1 N/A NEW Kenn.lin 11.15 Rokie 11.15 Sady 11/15创亿欣电子有限公司TRONIXIN ELECTRONICS CO.LTDHdmi c type SeriesConnectorProduct SpecificationSP-HDMI CM CONN-00 A 2/ 7Approved/Date Checked/Date Written/DateTom2012.11.15Rokie2012.11.15Kenn.lin2012.11.151.0 Scope :It applies to all products which specified the application of this standard. But, when there is an item which isn't based on this standard, it mentions to the product drawing about the item. The entry of this product drawing in the case has priority over more than this standard..2.0 Test Condition:Unless other wise specified elsewhere, the following characteristics shall be defined:3.1 Temperature range : +15℃ to +35℃3.2 Humidity range: 45% to 75%;3.3 Atmospheric Pressure : 86kPa to 106 kPa (860 to 1060 mber)But, it supposes that it has only a temperature and atmospheric pressure and that it is permitted to make a standard condition.3.0 Rating :3.1 Voltage: AC 40V[R.M.S]3.2 Current: 0.5A MAX/1 contact3.3 Rated temperature:storage : -40~60℃operating : -25~+85℃normal: +20℃4.0 Test Methods and Requirements:4.1 Examination of product:Item Test Description Test Methods Requirement4.1.1 Structure, dimensionand appearance EIA 364-18Shall be confirmed with eyes inaccordance with each drawing.Shall be confirmed by using propermeasuring instruments.1, The structure, the dimension, thematerial of the main components,and the surface finishing shall bespecified in the attached drawings.2, There shall be no scratches,cracks, stains or warps that aredetrimental to the function or theappearance of the connector创亿欣电子有限公司TRONIXIN ELECTRONICS CO.LTDHdmi c type SeriesConnectorProduct SpecificationSP-HDMI CM CONN-00 A 3/ 7Approved/Date Checked/Date Written/DateTom2012.11.15Rokie2012.11.15Kenn.lin2012.11.154.2 Electrical Performance:Item Test Description Test Methods Requirement4.2.1 Low Level ContactResistance EIA-RS-364-06BMate connectors：Measure by open circuit,20V maximum, 10m A.Contact: Initial Value 10m ohm Max.(Excluding conductor resistance)After Test, Change from Initial Value 30m ohm Max.EIA-RS-364-06BMate connectors：Measure by open circuit,5V maximum, 10m A.Shell: Change from Initial Value 50mohm Max.4.2.2 Insulation Resistance EIA –RS-364-21CUnmated connectors, apply 500V DCbetween adjacent terminal or ground;100 MΩ minimum. (unmated)EIA –RS-364-21CUnmated connectors, apply 150V DCbetween adjacent terminal or ground;10 MΩ minimum. (mated)4.2.3 DielectricWithstanding Voltage EIA-RS-364-20CUnmated connector, apply 500V AC(R.M.S) for 1 minute between adjacentterminal or ground.No damage.EIA-RS-364-20CUnmated connector, apply 300V AC(R.M.S) for 1 minute between adjacentterminal or ground.TRONIXIN ELECTRONICS CO.LTD Product Specification Tom2012.11.15Rokie2012.11.15Kenn.lin2012.11.154.3 Mechanical Performance:Item Test Description Test Methods Requirement4.3.1 Durability EIA-RS-364-09AMate and unmate samples for 5000cycles at maximum rate of 100±50cycles per hour. Contact resistance:Contact: Delta 30 mohm Max. Shell: Delta 50 mohm Max.4.3.2 Mating Force &Unmating Force. EIA-RS-364-13The force shall be measured with theplug at rate of 25±3 mm/minute. Thistest shall be made in a direction alongthe axis of both the socket and the plug.After 4 times, mating force andunmating force shall be measure.1, Mating Force:45N Max;2, Unmating Force:7N Min and 25 N Max.4.3.3 Vibration EIA-RS-364-28Amplitude: 1.52mm P-P or 147m/s2(15G)Sweep time: 50~2000-50Hz in 20minutes.Duration: 12times in each X.Y.Z axes.(total of 36 times)Electrical load: DC 100 mA currentshall be flowed during the test. 1, Appearance no damageno evidence2, Contact resistance Contact: delta 30 mohm Max; Shell: delta 50 mohm Max. 3, Discontinuity:1usec Max.TRONIXIN ELECTRONICS CO.LTD Product Specification Tom2012.11.15Rokie2012.11.15Kenn.lin2012.11.154.4 Environmental Performance:Item Test Description Test Methods Requirement4.4.1 Solderability MIL-STD-202F, Method 208After 5~10 seconds flux deep.Subject connector lead to solder bath at245℃ ± 5℃ for 5 ± 0.5 seconds. 1, Appearance: No evidence of physical damage.2, More than 95% of the solderable area shall be covered with solder.4.4.2 Humidity EIA-RS-364-31 AMated and unmated each connectorand perform the test as follows.Temperature: +25 to +85℃Relative Humidity: 80 to 95%;Duration: 4 cycles (96hours);Upon completion of the test,specimens shall be conditioned atambient room conditions for 24 hours,after which the specified measurementsshall be performed. 1, No evidence of physical damage. 2, Contact resistance:contact: change from initial value 30m ohm Max.shell: change from initial value 50 m ohm Max.EIA-RS-364-31 AMated and unmated each connector and perform the test as follows. Temperature: +25 to +85℃Relative Humidity: 80 to 95%; Duration: 4 cycles (96hours);Upon completion of the test, specimens shall be conditioned at ambient room conditions for 24 hours, after which the specified measurements shall be performed. 1, No evidence of physical damage. 2, Conform to item of dielectric withstanding voltage and insulation resistance.4.4.3 Salt Spray EIA-RS-364-26The connector specimen are testingwith the 5% salt water (NaCl ), 6.5~7.2PH, for 48hours of salt spray test. 1, Appearance no damage;2, Contact resistance: Contact: delta 30m ohm max; Shell: delta 50m ohm max.TRONIXIN ELECTRONICS CO.LTD Product Specification Tom2012.11.15Rokie2012.11.15Kenn.lin2012.11.154.4 Environmental Performance: (Continued)Item Test Description Test Methods Requirement4.4.4 Resistance tosoldering heat MIL-STD-202F, Method 210A, TestCondition B.The connector shall be testedresistance.To soldering heat in the followingconditions. (Refer fig.1)No evidence of physical damage.4.4.5 Temperature life(heat) MIL-STD-1344A, Method 1005.1The specimens shall be subjected toa temperature of 105℃ for 250 hours,and then placed in ambient temperaturefor more than 2 hours.1, No evidence of physical damage.2, Insulation resistance: 100M ohmMin. (Finally)4.4.6 Temperature life(cold) MIL-STD-1344A, Method 1005.1The specimens shall be subjected toa temperature of -40℃ for 250 hours,and then placed in ambient temperaturefor more than 2 hours.1, No evidence of physical damage.2, Insulation resistance: 100M ohmMin. (Finally)TRONIXIN ELECTRONICS CO.LTD Product Specification Tom2012.11.15Rokie2012.11.15Kenn.lin2012.11.155.0 Test Sequence:Test Group (a) Sample GroupsTest Item Test Description A B C D E F G H I J K L 4.1.1 Examination of product 1,3 1,5 1,3 1,3 1,3 1,5 1,5 1,3 1,5 1,54.2.1 Low Level Contact Resistance 2,4 2,44.2.2 Insulation Resistance 2,4 2,4 2,44.2.3 Dielectric Withstanding Voltage 24.3.1 Durability 34.3.2 Mating Force & unmating force 24.3.3 Vibration 24.4.1 Sorderability 24.4.2 Humidity 34.4.3 Salt Spray 34.4.4 Resistance to Soldering heat 24.4.5 Temperature Life ( heat) 34.4.6 Temperature Life ( cold) 3Number of Test Samples (Minimum) 5 5 5 5 5 5 5 5 5 5Note:a. S amples shall be prepare in accordance with applicable manufacture’s instructions and shal l be selected at random from current production.b. T he numbers in the table indicate sequence in which tests are performed.c. All the tests shall be performed in the sequence, indicated by the number in the columns.。
Dix-Lock N-Series 快速连接器说明说明书
Customer Service 877.963.4966Dix-Lock ®N-Series2877.963.4966 • Dix-Lock N-SeriesApplication• Full flow coupling used on utility, air, water, and nitrogen lines as well as pneumatic toolsFeatures• Non-valved design allows air flow to the tool, while providing a quick, secure connection • Convenient push-twist-click connection• Locking sleeve offered to enhance safe, reliable connections • S tainless steel retaining ring and spring maximizes corrosion resistance and extends service life • Highly versatile end configuration selection • Low profile prevents hose snags • I nterchangeable with Bowes 51000-Series, National Series 'B', MacDonald Quick-Action, Campbell Single-Lock • Conforms to MIL-C-3486 and A-A-50431A Interchange StandardMaterials • M achined components: manufactured using solid steel, brass, or 303 stainless steel bar stock, 316 stainless steel available in some versions upon request• Steel componentry: plated using ROHS Compliant Trivalent Chrome • Retaining ring and spring: stainless steel • Coupling sleeve: cast zinc steel• Locking ring: steel and brass nipple with aluminum ring, stainless nipple with stainless ring • Seals: pneumatically energized Nitrile (Nitrile Rubber)• Dust cap: steel and brass • Dust cap cable: carbon steelSpecifications• Temperature range: -40°F to 250°F (-40°C to 121°C)• P ressure rating: 300 PSI in brass, 500 PSI in steel and 303 stainless steel at ambient temperature70°F (21°C)Dix-Lock N-Series Pneumatic Couplings3877.963.4966 • Dix-Lock N-SeriesBody SizeSteel Coupler/ PlugBrass Coupler/ Plug 303 Stainless Steel Coupler/Plug Max Working BurstMax Working BurstMax Working BurstPSIBar PSI Bar PSI Bar PSIBar PSI Bar PSI Bar 3/8"500357,000480--------1/2"5003511,000755300208,2005655003512,600865Pressure RatingsNOTE: All dimensions are shown in inches unless otherwise notedFemale Head x Female Threaded End CouplersBrassSteel 303/316 stainless steelFemale Head x Male Threaded End CouplersBrass Steel303/316 stainless steelMale Head x Female Threaded End PlugsBrassSteel303/316 stainless steel4877.963.4966 • Dix-Lock N-Series5877.963.4966 • Dix-Lock N-SeriesMale Head x Male Threaded End PlugsMale Head x Male Threaded Safety Lock End PlugsBrassSteel303/316 stainless steelBrassSteel303 stainless steel6877.963.4966 • Dix-Lock N-SeriesMale End x Hose Barb Safety Lock PlugsBrass Steel303 stainless steelDix-Lock N-Series Pneumatic CouplingsMale End x Hose Barb PlugsBrass Steel303/316 stainless steelFemale Head x Standard Hose Barb CouplersBrassSteel303/316 stainless steel7877.963.4966 • Dix-Lock N-SeriesGender Change UnionCapsSeals3/4"1-10/64"BrassPlated steel BrassPlated steelBrass8877.963.4966 • Dix-Lock N-SeriesCrimped Dix-Lock N-Series Recommendation Guide• T he Crimped Dix-Lock Recommendation Guide is only a guide. It will not apply to every coupling situation. In some instancesalternative dies and crimping dimensions must be employed to ensure safety.• E xperience has shown that variances in the construction of similar hoses and couplings may cause some assemblies to react differently when crimped. It is not uncommon to find hose with an outer diameter that fluctuates from one end to the other or from production lot to production lot. • T hese inconsistencies coupled with the inherent differences between textile or wire braid, hard, or soft wall, the presence or absence of an internal spiral wire and the differences in hose coverings make it difficult to establish hard and fast rules.• T herefore, its imperative that hose dimensions are accurately measured, assemblies are tested, and documentation is maintained.• I t is important to be safe when installing quick disconnect couplings into a pneumatic circuit. Never install a pneumatic coupling directly into an air tool, use a piece of hose that is at least 18" long, between the tool and the coupling, to prevent damage to the coupling.• T o protect the operator, safety devices, such as a safety check valve and safety cable should be installed in case there is a hose or coupling failure. For safety cables and check valves, call Dixon 877.963.4966 or visit .Hose IDHose OD Crimp Diameter(± 0.005)Crimp Length %Reduction Fractional Decimal 1/2"54/64"0.844"0.917"1-1/8"18.955/64"0.859"0.929"1-1/8"18.956/64"0.875"0.942"1-1/8"19.057/67"0.891"0.954"1-1/8"19.058/64"0.906"0.967"1-1/8"19.059/64"0.922"0.980"1-1/8"19.060/64"0.938"0.992"1-1/8"19.061/64"0.953" 1.005"1-1/8"19.062/64"0.969" 1.018"1-1/8"19.063/64"0.984" 1.030"1-1/8"19.01" 1.000" 1.043"1-1/8"19.01-1/64" 1.016" 1.056"1-1/8"19.01-2/64" 1.031" 1.068"1-1/8"19.03/4"1-10/64" 1.156" 1.220"1-1/4"18.51-11/64" 1.171" 1.235"1-1/4"18.01-12/64" 1.187" 1.244"1-1/4"18.71-13/64" 1.203" 1.260"1-1/4"18.11-14/64" 1.218" 1.270"1-1/4"18.81-15/64"1.234" 1.285"1-1/4"18.21-16/64" 1.250" 1.295"1-1/4"18.81-17/64" 1.265" 1.310"1-1/4"18.41-18/64" 1.281" 1.320"1-1/4"18.81-19/64" 1.296" 1.335"1-1/4"18.51-20/64" 1.312" 1.345"1-1/4"19.01-21/64" 1.328" 1.360"1-1/4"18.51-22/64"1.343"1.370"1-1/4"19.0Dixon couplings and retention devices are designed to work safely for their intended use. The selection of the proper hose, coupling and retention device, and the proper application of the coupling to the hose are of utmost importance.Users must consider the size, temperature, application, media, pressure, and hose and coupling manufacturer'srecommendations when selecting the proper hose assembly components. Dixon recommends that all hose assemblies be tested in accordance with the Association for Rubber Products Manufacturer's (ARPM) recommendations and be inspected regularly (before each use) to ensure that they are not damaged or have become loose. Visit for more information.Where safety devices are integral to the coupling, they must be working and utilized. The use of supplementary safety devices such as safety clips or safety cables are recommended.If any problem is detected, couplings must be removed from service immediately.Dixon is available to consult, train and recommend the proper selection and application of all fittings we sell. We strongly recommend that distributors and end users make use of Dixon Testing and Recommendation Services. Call 877.963.4966 or visit to learn more.SafetyNOTE: All dimensions are shown in inches unless otherwise noted9877.963.4966 • Dix-Lock N-SeriesNotes10877.963.4966 • Dix-Lock N-Series11877.963.4966 • Dix-Lock N-Series Dixon by its supplier; (b) any product that has been subject to abuse, negligence, accident, or misapplication; (c) any product altered or repaired by others than Dixon; and (d) to normal maintenance services and the replacement of service items (such as washers, gaskets, and lubricants) made in connection with such services. To the extent permitted by law, this limited warranty shall extend only to the buyer and any other person reasonably expected to use or consume the goods who is injured in person by any breach of the warranty. No action may be brought against Dixon for an alleged breach of warranty unless such action is instituted within one (1) year from the date the cause of action accrues. This limited warranty shall be construed and enforced to the fullest extent allowable by applicable law.Other than the obligation of Dixon set forth herein, Dixon disclaims all warranties, express or implied, including but not limited to any implied warranties of merchantability or fitness for a particular purpose, and any other obligation or liability. The foregoing constitutes Dixon's sole obligation with respect to damages, whether direct, incidental, or consequential, resulting from the use or performance of the product.Some products and sizes may be discontinued when stock is depleted or may require a minimum quantity for ordering.CopyrightCopyright © 2021 by Dixon Valve and Coupling, LLCAll rights reserved. This book is copyrighted material. Use, reproduction or copying of it by anyone other than Dixon ® is strictly forbidden without its express written consent.About This Catalog and Our ProductsThis catalog is intended as a product offering. It is not a user or technical manual. Information in this catalog is subject to change without notice. We may modify product design and specification without notice and without any obligation to modify or substitute products previously purchased. All users and distributors of products sold through this catalog are strongly encouraged to contact Dixon with questions on use, compatibilities, coupling procedures, and life of product. Our full-time engineering and test staff are always available to recommend uses and to assist distributors and users with questions.SafetyTrademarksDelrin ® and Zytel ® are registered trademarks of DuPont Nemours and Company.Kalrez ® is a registered trademark of DuPont Dow Elastomers.All other trademarks appearing in the Dixon illustrated price list are the property of their respective owners.Safety logos, which appear throughout our catalog, are used as a reminder that the user should carefully review for the appropriateness of the product for the media, application, and environment in which it will be used.NOTE: Because of the health hazards associated with contamination and lead content in drinking water systems, Dixon couplings, unless otherwise specifically approved, are not recommended for potable water service and should not be used in applications where drinking water will contact the wetted surfaces of the coupling.All Dixon products are shipped in cartons with the following warning:"WARNING: This product contains lead, a chemical known to the State of California to cause cancer and birth defects or other reproductive harm."© 2021 DVCC Printed in the USA DIXLOCK_11211 Dixon Square Chestertown, MD 21620Phone: 877.963.4966Email:********************Dixon ®connect with us on。
XG5N系列连接器套头产品说明书
XG5N-241XG5W-0231XG5N-502Crimped MIL Connector Sockets for Discrete WiresXG5N/XG5N-U1Crimped Sockets for Discrete Wires Join the MIL Connector Series•XG5N-U Sockets with OMRON’s unique lock enable one-hand insertion with a secure lock.•Save up to 24%of the space required for theXG4A.■Ratings and Characteristics■Materials and Finish■Applicable Contacts and WiresXG5N-UDiscrete wiresXG4CXG5NXG5N Socket XG4A Plug XG5N-U Socket with Lock XG4C Plug2Crimped MIL Connector Sockets for Discrete WiresXG5N/XG5N-U■XG5N /XG5N-UDimensions (Unit:mm)Ordering Information*Order the required number of reels (10,000contacts).Note:1.Each XG5N-@@@connector requires two lock levers.(XG5U-0001is not packaged as a pair of levers).2.The pitch between the two polarity guides on Connectors with 50,60,or 64contacts is 22.86mm.(15.6)(16.4)(C)(D)14.46.102.54BA 2.546.107.902.54BA 2.54XG5N-U (with Lock Levers Attached)XG5NNo.of contactsDimension (mm)A B C D1017.2610.1626.8026.201422.3415.2431.8831.281624.8817.7834.4233.822029.9622.8639.5038.902637.5830.4847.1246.523042.6635.5652.2051.603447.7440.6457.2856.684055.3648.2664.9064.305068.0660.9677.6077.006080.7673.6690.3089.706485.8478.7495.3894.78AppearanceSocketandLockSet Note:The Locks and Sockets are provided separately.Socket HousingLock Levers (See note 1)Crimp Contacts,Type 1Crimp Contacts,Type 2No.of contactsNo.of polarity guidesModel Model Model Model Model100XG5N-100-U XG5N-100XG5U-0001XG5W-0231(loose contacts)XG5W-0231-R*(reel contacts)XG5W-0232(loose contacts)XG5W-0232-R*(reel contacts)1XG5N-101-U XG5N-101141XG5N-141-U XG5N-141161XG5N-161-U XG5N-161201XG5N-201-U XG5N-201261XG5N-261-U XG5N-261301XG5N-301-U XG5N-301341XG5N-341-U XG5N-341401XG5N-401-U XG5N-401501XG5N-501-U XG5N-5012XG5N-502-U XG5N-502601XG5N-601-U XG5N-6012XG5N-602-U XG5N602641XG5N-641-U XG5N-6412XG5N-642-UXG5N-642Crimped MIL Connector Sockets for Discrete WiresXG5N/XG5N-U3ContactRemovalToolXY2E-0003TEL 03-3756-1434China:Japan Automatic Machine T echnology (Huizhou)Ltd.6-1-B,Songshan Industrial Park,Huizhou Zhongkai Hi-T ech Industrial Development Zone,Huizhou,Guangdong,China TEL(86-752)2771-614FAX(86-752)2771-619South-eastern Asia:Japan Automatic Machine Singapore Pte.Ltd.HB Centre 12T annery Road #04-02,Singapore 347722TEL 65-6545-8140FAX 65-6545-8141USA,Europe:T oyojamco,Ltd.8370Burnahm Road Suite 200EL Paso,TX 79907USA TEL (915)595-8825FAX (915)595-8794*1:Inquire for details.*2:This model number is for standard specifications.Inquire for other specifications.Safety PrecautionsAlways use the specified Crimping T ool or Applicator to wire the crimped contacts.Refer to the instruction sheet that is provided separately for details.Contact Insertion MethodConfirm the orientation of the crimped contacts and then insert them all the way to the back of the Socket.After insertion,confirm that the lances are securely set in the lance holes on the socket housing.Contact Replacement MethodT o remove contacts that have been incorrectly inserted,always use the XY2E-0003Contact Removal T ool.1.Insert the end of the Removal T ool into the lance hole in the socket housing and press the lance all the way inside the socket housing.2.While pressing in on the lance,pull out the Contact.3.Insert a new Contact.Note:Do not use any Contacts that havebeen removed.Attach the holes in the Lock Levers to the protrusions on both sides of the housing and make sure that they are set securely.Precautions for Correct UseWhen mating the Sockets with XG4C Box Plugs,always use the XG5U-0001Lock Levers.Otherwise the Connectors may become disconnected due to vibration or shock.Storage1.Do not store the Sockets in locations subject to dust or high humidity.2.Do not store the Sockets in locations close to sources of gasses such ammonia gas or sulfide gas.Before Insertion After Insertion (Set in Socket)4Crimped MIL Connector Sockets for Discrete WiresXG5N/XG5N-UOMRON ON-LINEGlobal -USA -Cat.No.G023-E-03Printed in USAOMRON ELECTRONIC COMPONENTS LLCmerce Drive,Suite B Schaumburg,IL 60173847-882-228808/13Specifications subject to change without noticeAll sales are subject to Omron Electronic Components LLC standard terms and conditions of sale,which can be found at /components/web/webfiles.nsf/sales_terms.html ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.T o convert millimeters into inches,multiply by 0.03937.T o convert grams into ounces,multiply by 0.03527.XG5N-241XG5W-0231XG5N-502。
Fujitsu 560H 系列 Compact Flash 卡插座连接器说明书
COMPACT FLASH CARD CONNECTORS560H SERIES (CFA COMPATIBLE)s FEATURES•The connectors conform to the Compact Flash Association (CFA) specifications.•The terminal of the plug is a 0.635 mm pitch, one-row, SMT type.•Raised mounting type connectors (standoff), which allow mounting components under a connector, are also available.•The ejector mechanism makes insertion and ejection of a card easier is available.•There are two types of sockets for CFA cards: a straddle mount type and single-sided mounting type.s SPECIFICATIONSs PIN CONNECTOR (PLUG) CONTACT LENGTHsMATERIALSme t I la i r e t a M l a i r e t a m g n i t a l u s n I 0-V 49L U n i s e r S P P :y d ob n i a M 0-V 49L U T B P :e d i u G 0-V 49L U S B A :n o t t u B r o tc ud n o C y o l l a re p p o C gn i t a l P dl o g :t c a t n o C mu i d a l l a p :l a n i m r e T e p y T t c a t n o C .o n n i P h t g n e l t c a t n o C s n i p d n u o r g ,r e w o P 05,83,31,1).n i 691.0(m m 89.4s n i p n o i t c e d d r a C 62,52).n i 731.0(m m 84.3sn i p l a n g i s r e h t O re h t O ).n i 761.0(m m 42.4me t I no i t a c i f i c e p S e g n a r e r u t a r e p m e t g n i t a r e p O C °58+o t °55-t n e r r u c d e t a R C D A 5.0e g a t l o v d e t a R CA V 052e c n a t s i s e r t c a t n o C m 08Ω)A m 01,V m 02C D (x a m e c n a t s i s e r n o i t a l u s n I M 0001Ω,C D V 005,.n i m eg a t l o v d n a t s h t i w c i r t c e l e i D CD V 005RIGHT ANGLE PLUG, SMT TYPE (WITH NO EJECTOR)sDIMENSIONSs PC BOARD MOUNTING PATTERN (MOUNTING SIDE)s ORDERING PART NUMBER FCN-568H050-G/A1For above connector with ejector mechanism see page 3.Unit: mm (in.)Unit: mm (in.)40.16 (1.581)31.115±0.2 (1.225±.008)0.635±0.15(.025±.006)2x Ø2.2(.086)2x 4(0.157)2x2(0.079)35.9 (1.413)50.6 (1.992)16 (.630)19 (.749)25 (.984)26.5 (1.043)1(.039)4.5 (.177)4.5 (.177)1.25(.049)43.03±0.06 (1.225±.002)B30.48 (1.200)No. 13No. 381.27(.050)1.27(.050)1.4±0.05(.055±.002)No. 1No. 13BNo. 25No. 5040.16 (1.581)2x0.89±0.05(.035±.002)0.79±0.06 (.031±.002)1.75 (.069)2.6±0.03 (.102±.0001)2(.079)2.5 (0.098)5.25 (0.207)3.5 (0.138)4.5 (0.177)φ1.5+0 (0.059+0 )-0.1-0.004 3.5±08 (0.138±003)1(0.039)1 (.039)5.1(0.201)2.54 (0.1)1.8(.071)9.5 (0.374)11 (0.433)Section B-BRecommended PCB Pattern2 x 3(.079 x .118)46.13±0.15 (1.816±0.006)40.16±0.05 (1.581±0.002)31.115±0.05 (1.225±0.002)0.635±0.03 (0.025±0.001)2 × φ1.7±0.03(0.67±0.001)2 × φ2.2±0.05 (0.087±0.002)2±0.15(0.079±0.006)7.55±0.05(0.297±0.002)3.5±0.05(0.138±0.002)3±0.1 (.118±0.004)2 × 5±0.15(0.197±0.006)0.4±0.03 (0.016±0.001)No.38No.50No.26No.13No.1No.2547.10 -0 (1.854-0)7.45 (0.293)3.5 (0.138)5.55-0 (0.219-0)3 (.118)7.6-0(0.299-0)20.5-0(0.807-0)1.85-0.1 (0.073-0.004)+0+0The End of the P.C. BoardComponent mounting prohibited areaComponent mounting prohibited areas ORDERING PART NUMBER FOR CONNECTOR/EJECTOR KIT FCN-568H050-G/A1ACRIGHT ANGLE PLUG, SMT TYPE (WITH EJECTOR)sDIMENSIONSUnit: mm (in.)47.6 (1.874)23.8 (0.937)27.3 (1.074)5.5 (0.217)10.65 (0.420) a t c a r d e j e c t e d17.4 (0.685) a t c a r d i n s e r t e d6.75(0.266)29.25 (1.151)10.95 (0.431)28.6 (1.126)7.85 (0.309)0.3 (0.012)5.8 (0.228)1.5 (0.060)Connector/Ejector KitConnector/Ejector mechanism (P/N FCN-560HAC)RIGHT ANGLE PLUG, SMT TYPE (WITH NO EJECTOR, TO BE MOUNTED ON BACK OF PC BOARD)sDIMENSIONSs PC BOARD MOUNTING PATTERN (MOUNTING SIDE)s ORDERING PART NUMBER FCN-568H050-G/A2For above connector with ejector mechanism see page 5.Unit: mm (in.)Unit: mm (in.)40.16 (1.581)31.115±0.15 (1.225±0.006)0.635±0.15(0.025±0.006)2 x φ2.2(0.086)2 X 4(0.157)4.5(0.177)1 (0.039)1(0.039)16 (0.630)19 (0.749)25 (0.984)26.5 (1.043)1.25 (0.049)5.1 (0.201)2.5 (0.098)3.5±08 (0.138±003)5.25 (0.207)3.5 (0.138) 11 (0.433)φ1.50 (0.0590)000035.9 (1.413)2 x 0.89(0.035)50.6 (1.992)43.03±0.06 (1.225±0.002) 1.27(0.050)1.27 x (25-1) = 30.48 (1.200)No. 38No. 262 X 2.0 (0.079)40.16 (1.581)1.400(0.055000)BNo. 50No. 25No. 13 0.79 00(0.031000)No. 11.27 (0.050)4.5 (0.177)1.5(0.059)4.5 (0.177)2.54 (0.1)Section B-BB9.5(0.374) 1.8(0.070)No.13No.1No.25No.50No.38No.262±0.15(0.079±0.006)7.55±0.05 (0.297±0.002)3.5±0.05(0.138±0.002)0.4±0.03 (0.016±0.001)46.13±0.15 (1.816±0.006)0.635 × (50 – 1)= 31.115±0.05 (1.225±0.002)0.635±0.03(0.025±0.001)2 × φ1.7±0.03(0.67±0.001)2 × φ2.2±0.05(0.087±0.002)3±0.1(118±0.004)2 × 5±0.15(0.197±0.006)Recommended PCB pattern47.10 -0 (1.854-0)7.45 (0.293)3.5 (0.138)5.55 (0.219)3 (0.118) 7.6-0(0.299-0)20.5-0(0.807-0)1.85-0.1(0.073-0.004)+0+0The End of the P.C. BoardComponent mounting prohibited areaComponent mounting prohibited area2 x 3(.079 x .118)s ORDERING PART NUMBER FOR CONNECTOR/EJECTOR KIT FCN-568H050-G/A2ADRIGHT ANGLE PLUG, SMT TYPE (WITH EJECTOR, TO BE MOUNTED ON BACK OF PC BOARD)sDIMENSIONSUnit: mm (in.)47.6 (1.874)23.8 (0.937)27.3 (1.874)5.5 (0.217)10.65 (0.420) w h e n c a r d i s e j e c t e d17.4 (0.685)w h e n c a r d i s i n s e r t e d29.25 (1.151)10.95 (0.431)28.6 (1.126)0.3 (0.011)5.8 (0.228)1.5 (0.060)7.85 (0.309)Connector/Ejector KitConnector/Ejector mechanism (P/N FCN-560HAD)RIGHT-ANGLE PLUG, SMT TYPE (WITH NO EJECTOR, 1.64mm RAISED TYPE)sDIMENSIONSs PC BOARD MOUNTING PATTERN (MOUNTING SIDE)s ORDERING PART NUMBER FCN-568H050-G/A3For above connector with ejector mechanism see page 7.Unit: mm (in.)Unit: mm (in.)No.38No.50No.26No.1No.13No.252 × 3(0.079 x 0.118)2±0.15(0.079±0.006)7.55±0.05 (0.297±0.002)3.5±0.05(0.138±0.002)0.4±0.03 (0.016±0.001)46.13±0.15 (1.816±0.006)40.16±0.05 (1.581±0.002)0.635 × (50 – 1)= 31.115±0.05 (1.225±0.002)0.635±0.03 (0.025±0.001)2 × φ1.7±0.03(0.67±0.001)2 × φ2.2±0.05(0.087±0.002)3±0.1 (118±0.004)2 × 5±0.15(0.197±0.006)Recommended PCB patternComponent with 1.1 mm (0.043 in.)or less height can be mounted.47.10 -0 (1.854-0)7.45 (0.293)2.3(0.090)3.5 (0.138)5.55 (0.219)3 (0.118)7.6-0(0.299-0)20.5-0(0.807-0)3.0-0 (0.118-0)1.85-0.1 (0.073-0.004)+0+0The End of the P.C. BoardComponent mounting prohibited area Component mounting prohibited area50.60 (1.992)40.16 (1.581)31.115±0.15 (1.225±0.006)35.9 (1.413)2 x 0.89±0.05(0.035±0.002)2.0 (0.079)1.64 (0.065)2.5 (0.098)43.03±0.06 (1.225±0.002)0.635±0.15 (0.025±0.006)2 x φ2.2(0.086)2x 4(0.157)4.5(0.177)1 (0.039)16 (0.630)19 (0.749)25 (0.984)26.5 (1.043)4.5(0.177)5.25 (0.207)3.5(0.138)4.5 (0.177)11 (0.433)1.75 (0.069)1.27 (0.050)1.27(0.050)0.79 ±0.05(0.031±0.002) 1.4 ±0.05(0.055±0.002)φ1.5+0(0.059+0 )-0.1-0.004No. 1No. 26No. 38No. 13No. 25No. 503.5±08 (0.138±003)1(0.039)6.64 (0.261)BBASection B-B1.25 (0.050)2.54 (0.1)1.5 (0.060)9.5(0.374)1.8(0.070)30.48 (1.2)s ORDERING PART NUMBER FOR CONNECTOR/EJECTOR KIT FCN-568H050-G/A3ACRIGHT-ANGLE PLUG, SMT TYPE (WITH EJECTOR, 1.64mm (0.065 in.) RAISED TYPE)sDIMENSIONSUnit: mm (in.)1.84 (0.072)7.34 (0.289)Connector/Ejector Kit47.6 (1.874)23.8 (0.937)27.3 (1.074)5.5 (0.217)10.65 (0.420)w h e n c a r d i s e j e c t e d17.4 (0.685)w h e n c a r d i s i n s e r t e d6.75(0.266)28.6 (1.126)29.25 (1.151)4.05(0.159)1.5 (0.060)10.95 (0.431)7.85 (0.309)Connector/Ejector mechanism (P/N FCN-560HAC)RIGHT-ANGLE PLUG, SMT TYPE (WITH NO EJECTOR, 1.64mm (0.065) RAISED TYPE, TO BE MOUNTED ON BACK OF PC BOARD)s DIMENSIONSs ORDERING PART NUMBER FCN-568H050-G/A4For above connector with ejector mechanism see page 9.s ORDERING PART NUMBER FCN-568H050-G/A4ADRIGHT-ANGLE PLUG, SMT TYPE (WITH EJECTOR, 1.64mm (0.065 in.) RAISED TYPE, TO BE MOUNTED ON BACK OF PC BOARD)sDIMENSIONSUnit: mm (in.)6.75 (0.265)1.84 (0.072)7.34 (0.289)4.05 (0.159)Ejector mechanism (P/N FCN-560 HAD)Connector/Ejector Kit47.6 (1.874)23.8 (0.937)27.3 (1.074)5.5 (0.217)10.95 (0.431)7.85 (0.309)10.65 (0.420)w h e n c a r d i s e j e c t e d17.4 (0.685)w h e n c a r d i s i n s e r t e d29.95 (1.151)28.6 (1.126)1.5 (0.060)Part No: FCN-560HAC10.95 (0.431)5.5 (0.216)47.6 (1.874)23.8 (0.937)26.75 (1.053)5.5 (0.217)10.65 (0.420)w h e n c a r d i s e j e c t e d17.4 (0.685)w h e n c a r d i s i n s e r t e d28.6 (1.126)4.05(0.159)7.85 (0.309)29.25 (1.151)6.75 (0.266)FCN-560H Series Connector PLUG (Guide)Part No: FCN-560HAD10.95 (0.431)5.5(0.216)47.6 (1.874)23.8 (0.937)27.3 (1.075) 5.5 (0.217)10.65 (0.420)w h e n c a r d i s e j e c t e d17.4 (0.685)w h e n c a r d i s i n s e r t e d4.05(0.159)7.85 (0.309)29.25 (1.151)6.75 (0.266)28.6 (1.126)FCN-560 Series Connector PLUG (GUIDE)560H Series (Compact Flash Connector)11Dimensions are in millimeters (inches) Specifications subject to change© 2001 Fujitsu Components America, Inc. All company and product names are trademarks or registered trademarks of their respective owners. Rev. 09/2001JapanFujitsu Component Limited Gotanda-Chuo Building3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010Fax: (81-3) 5449-2626Email:************** Web: North and South AmericaFujitsu Components America, Inc.250 E. Caribbean DriveSunnyvale, CA 94089 U.S.A.Tel: (1-408) 745-4900Fax: (1-408) 745-4970Email:*******************.com Web: EuropeFujitsu Components Europe B.V.Diamantlaan 252132 WV Hoofddorp NetherlandsTel: (31-23) 5560910Fax: (31-23) 5560950Email:***************************.com Web: Asia PacificFujitsu Components Asia Ltd.102E Pasir Panjang Road#04-01 Citilink Warehouse Complex Singapore 118529Tel: (65) 375-8560Fax: (65) 273-3021Email:*****************.com Fujitsu Components International Headquarter Offices。
ITT Industries ARINC 600 数据手册
ARINC 600 BKAD/E/FLow insertion force contacts.Both environmental and non- environmentalversions.Polarizing posts that are removable from themating face.Field replaceable inserts for size 22 andpower contacts.Up to 800 size 22 contacts in one connector.Crimp, coax, power, printed circuit and wirewrappable post style contacts.Uses standard DPX crimp, insertion/extractiontooling.Waveguide connections available.BKAD/E BKAD/E connectors represent a major milestones in presenting a new rack and panel connector for support of the air transportation market.Several important design concerns have been ad-dressed and solved in this new series. High mating forces of pluggable modules in a rack have been reduced by approximately two-thirds.The low insertion force contacts are also inter-changeable with the contacts used in the DPX series and permit retrofit of existing equipment.BKAFThis new connector is totally intermateable andintermountable with ARINC 600 connectors now inthe field.The BKAF permits the user to easily replace acontact in case of problems, rather than disas-semble the entire connector--it is available withsize 22 contacts in wrap post or solder-tail ver-sions. The system maintains the advantages of lowinsertion force technology incorporated in all ARINC600 connectors.Rear Release/Rear Removable Size 12, 16, 20, 22 Crimp Contacts Front Release/Front RemovableSize 22 Solder Tail and Wrap Post ContactsPos-Aline Connector Construction FeatureMaterial SpecificationsIn the ARINC 600 connector series, Size 22 con-tacts are the only size that utilize this design feature. The hooded socket extends from its in-sulator while the pin contacts are shrouded by its front insulator.All other contacts used in this series employ stan-dard contact design.The result is that the complement of contacts forthe plug connectors will consist of pin contacts forsize 22 and socket contacts for all others. Thereceptacle contacts will be just the reverse, socketcontact for size 22 and pin contacts for thebalance.Shell & Waveguide BKAD BKAE BKAF SpecificationsInsulator Contacts Grommets/Seals O-Ring Finish Material Material Material Finish Termination Material Material 1200Alodine Thermoset Aluminum alloy Copper alloy Gold over Nickel Crimp N/A N/A 1200Alodine Thermoset Aluminum alloy Copper alloy Gold over Nickel Crimp Silicone-based Elastomer Silicone-based Elastomer 1200Alodine Thermoset Aluminum alloy Copper alloy Gold over Nickel P .C./Wrap Post N/A N/A MIL-C-5541N/AQQ A-591/A380QQ-C-533MIL-G-45204N/AN/A N/A* = For Polarizing Position greater then 99, add third digit.ARINC 600 BKAD/E/F CONNECTOR SERIESCLASSSHELL SIZECONNECTOR LAYOUT DESCRIPTIONSIZE 1 COAX INSERT MODIFIERBOEING COAX MODIFIERSHELL STYLECONNECTOR MOUNTING MODIFIERPOLARIZING POSITIONMODIFIER (Contact, Finish, Material)How to OrderBKA D 2 A234 M * 3 00 01 * F0CONNECTOR SERIES BOEING COAX MODIFIERSHELL STYLE CONNECTOR MOUNTING MODIFIERCLASS Non-environmental (rear release, crimp contacts)Environmental (rear release, crimp con-tacts)Non-environmental (front release, solder and wrap post #22 contact, rear release all others)Same as E, except uses BKAD shells, and Less 0 rings on plug side.Environmental (0-ring is used to seal between connector shell and insulators)with rear release, crimp contacts.Non-environmental connector using fil-tered contacts (reference Cannon Phoe-nix)Max. contact capacity - 125Max. contact capacity - 400Max. contact capacity - 800Connector contains modified 71W1 or 2W2 insert (four MTG screw hole loca-tions and coaxial contact used in this insert are interchangeable between dif-ferent manufacturers Plug (rack side)Receptacle (box side)Standard design, .148 dia. holesWith #6-32 ESNA (#12 NCFMA2-62) clinchnuts (see chart)Size 1 receptacle only - less 3 printed circuitboard mounting lugsWith #4-40 ESNA (#22 NCFMA2-40) clinchnuts (see chart)Size 2 and 3 plug and receptacle only - with#4-40 ESNA (#22 NCFMA2-40) clinch nuts(all mounting holes)Size 2 and 3 plug and receptacle only - with#6-32 ESNA (#12 NCFMA2-62) clinch nuts(all mounting holes)Same as - 00 mounting modification exceptwith nickel finished shells .0008 - .0012 thickwith EMI grounding spring for plug shells and supplied with non-environmental inserts.Same as - 00 mounting modification exceptwith nickel finished shells .0008 - .0012 thickwith EMI grounding spring for plug shells andsupplied with environmental inserts not pottedinto shell.With floating eyelets (.048 min. radial float)4 corner holes per connector.Consult factory if other modifications are requiredSHELL SIZE CONNECTOR LAYOUT DESCRIPTION SIZE 1 COAX INSERT MODIFIER NOTE: A dash must be inserted whenever code does not apply.D BKA (Per ARINC 600)E F C S T 3 -4 -00 -01 -02 -03 -08 -09 -16 -17 -23 -M 123(See page 4)----------BoeingCoax Code Connector Size 1234484610Number of Clinch NutsPlug ReceptacleITTC Code Plug Connector Receptacle ConnectorITTC Coax Contacts SuppliedAA AB AC AD AE AF Blank B C D E F No Coax Supplied 349-0013-000 349-0015-000 349-0013-000 349-0017-000 349-0015-000 349-0018-000 349-0015-000 349-0017-000No Coax Supplied349-0014-000349-0016-000349-0014-000349-0002-000 349-0016-000349-0004-000349-0016-000349-0002-000AR INC 600 B K AD/E/F How to Order (Continued)CONNECTOR LAYOUT DESCRIPTION NOTE. ANY OTHER COMBINATION OF INSERTS WITHIN A SPECIFIC SHELL IS AVAILABLE UPON REQUESTPOLARIZING POSITION MODIFIER (Contact, Finish, Material)01 thru 99 (per ARINC 600)Blank-Polarizing posts or keys not installed butsupplied with connectorBlank -SC -WC -WD -SD -WA -WB -Rear release, crimp, signal and power contacts supplied with connector (when applicable)Contacts not supplied with connector (FO not stamped on connector)Less contacts and waveguide (FOO not stamped on connector)Front release .025(0.63) D. x .150(3.81) solder post and crimp, rear re-lease power contacts (when applica-ble) supplied with connector Front release .025(0.63) D. x .250(6.35) solder post and crimp, rear re-lease power contacts (when applica-ble) supplied with connector Front release .025(0.63) D. x .375(9.53) solder post and crimp, rear re-lease power contacts (when applica-ble) supplied with connector Front release .025(0.63) D. x .500(12.7) solder post and crimp, rear re-lease power contacts (when applica-ble) supplied with connector Front release .025(0.63) Sq. x .250(6.35) (1 wrap) wrap post and crimp,rear release power contacts (when ap-plicable) supplied with connectorFront release .025(0.63 Sq. x .375(9.53) (2 wraps) wrap post and crimp,rear relase power contacts (when ap-plicable) supplied with connectorFront release .025(0.63) Sq. x 500(12.7) (3 wraps) wrap post and crimp,rear release power contacts (when ap-plicable) supplied with connectorFront release .025 (0.64) Sq. x 641(16.28) (3 wraps) wrap post andcrimp, rear release power contacts (when applicable) supplied with con-nectorNOTE: COAXIAL CONTACTS TO BE ORDERED SEPARATELY FO -FOO -SA -SB -Layout included in the following ARINC configurations 702, 710, 711, 712, 714, 715, 716, 723.Layout included in the following ARINC configurations 707, 718 & 730.Layout included in the following ARINC configurations 701, 702, 703, 704, 705, 706, 724, 725.Layout included in the following ARINC configurations 701, 717, 726, 729.Note: All layouts with "OPEN' insert cavity are not supplied with an insulator. If a Blank insert is required please consult factory.Retainer Plate *This dimension indicates distance from centerline of retaining screw to the centerline of first contact cavity.For further information, refer to ARINC 600 specification or consult factory.Size 1 Receptacle Panel CutoutRetainer Plate Size 1 Plug Panel CutoutReceptacleFor further information, refer to ARINC 600 specification or consult factory.* This dimension indicates distance from centerline of retaining screw to the centerline of first contact cavity.BKAE SERIES 1.550 (39.37) MAX C B A BKAE SERIES 1.670 (42.42)11550 (39.37) MAXBKAE SERIES130 (3.30.120 (3.05)1.317 (33.45).355 (9.02)1.5301.670 (42.42)Retainer Plate*This dimension indicates distance from centerline of retaining screw to the centerline of first contact cavity.For further information, refer to ARINC 600 specification or consult factory.Size 2 Receptacle Panel Cutout Retainer Plate Size 2 Plug Panel Cutout ReceptacleFor further information, refer to ARINC 600 specification or consult factory.* This dimension indicates distance from centerline of retaining screw to the centerline of first contact cavity.BKAE SERIES 1.550 (39.37) MAX1.670 (42.42 )MAX Retainer Plate ReceptacleSize 3 Plug Panel Cutout* This dimension indicates distance form centerline of retaining screw to the centerline of first contact cavity.For furter information, refer to ARINC 600 specification or consult factory.Retainer Plate Size 3 Plug Panel Cutout* This dimension indicates distance form centerline of retaining screw to the centerline of first contact cavity.For furter information, refer to ARINC 600 specification or consult factory.Contact Arrangements - Shell Size 1Contact Arrangements - Shell Sizes 2 and 3BKAD/BKAE (Plug Rear face shown)BKAD/BKAE (Plug Rear face shown)REAR SURFACE WHITE ON BLUE TO INDICATE REAR RELEASE REAR REMOVAL CONTACTS ENGAGING END SURFACE WHITE ON RED TO INDICATEFRONT RELEASE FRONT REMOVAL CONTACTS**Pending ARINC release.NOTE: In layouts using #22 contacts mixed with any other contact size (20HD, 16, 12), the size #22 contact type (pin or socket) determines the insulator as a pin insert or a socket insert.(For Contact Cavity Location and Contact Cavity Identification refer to ARINC 600 or consult factory)REAR SURFACE WHITE ON BLUE TO INDICATE REAR RELEASE, REAR REMOVAL CONTACTS FOR INSERTS CONTAINING STANDARD SIGNAL & POWER CONTACTS(For Contact Cavity Location and Contact Cavity Identification refer to ARINC 600 or consult factory)30T228 #222 #8 TWINAX/COAX (#8 Grounded to Shell)6060 #226**6 #86T6**6 #8(Metallic Insert)13W24 #20, 4 #12, 3 #162 #5 COAX24T4**20 #20, 4 #8100100 #228580 #22, 4 #20, 1 #1659**50 #22, 5 #16, 4 #1234**24 #20, 10 #1844 #125W21 #122 #162 #5 COAX 4040 #226060 #225W21 #122 #162 #5 COAXBKAF - Available Receptacle Shell Only(Front Release)Shell Cavity A or B Shell CavityC or FShell Cavity C Shell CavityC Shell CavityA or BBKAD/BKAE (Plug Rear face shown)Shell CavityA,B,D,E2W22 #1 COAX 4W44 Modified #1 COAX (Metallic Insert)10T10**10 #8 TRIAX/COAX (#8 Grounded to Shell)(Metallic Insert)24**24 #1271W170 #221 #1 COAX 71W1B70 #221 #1 COAX60**60 #2049T2**47 #202 #8110**100 #225 #12 & 5 #20** Pending ARINC release.(For Contact Cavity Location and Contact Cavity Identification refer to ARINC 600 or consult factory)REAR SURFACE WHITE ON BLUE TO INDICATE REAR RELEASE. REAR REMOVAL CONTACTS FOR INSERTS CONTAINING STANDARD SIGNAL & POWER CONTACTS150150 #22120T2 **118 #222 #8 TWINAX/COAX (#8 Grounded to Shell)121**110 #225 #166 #20BKAF - Available Receptacle Shell ONLY(Front Release)SHELL CAVITYA, B, D, E,BKAF - Available Receptacle Shell ONLY(Front Release)SHELL CAVITY C, F** Pending ARINC release.NOTE #22 CONTACTS ARE SOCKETS, 20HD,16, 12 ARE PIN CONTACTS.(For Contacts Cavity Location and Contact Cavity Identification refer to ARINC 600 or Consult Factory)ENGAGING END SURFACE WHITE ON RED TO INDICATE FRONT RELEASE FRONT REMOVAL CONTACTS FOR INSERTS CONTAINING STANDARD SIGNAL & POWER CONTACTS ENGAGING END SURFACE WHITE ON RED TO INDICATE FRONT RELEASE, FRONT REMOVAL CONTACTS FOR INSERTS CONTAINING STANDARD SIGNAL & POWER CONTACTS 71W170 #22150150 #226T6**6 #813W24 #203 #164 #122 #5 COAX100100 #2271W1B 70 #2210T10**10 #8121F**110 #226 #205 #16Waveguide ConnectionsPolarization (Engaging End)WAVEGUIDE DETAIL SHOWN FULLY ENGAGEDFULLYCENTERPOSTRIGHTPOSTLEFTPOSTCENTERPOSTRIGHTPOSTLEFTPOST INSULATOR ANDWAVEGUIDE RETAININGPLATEPlugBKA*1PLUG RECEPTACLE PLUG RECEPTACLEBKA*2BKA*3ReceptaclePolarizing PositionsPOST Dark area represents postPlug Shell Receptacle ShellKEYKit P/N 320-1067-000Kit P/N 320-1067-003Contact and Termination Tooling DataBKA* (LIF) Crimp ContactsBKAF-ARINC 600 Size 22 Wrap Post Socket Contacts With .025(6.35) Square Wire-Wrappable Tails-Receptacle Only.BKA* Thermocouple ContactsBKAF Printed Circuit Solder Post Socket Contacts Size 22 with .025(6.35) Dia. Printed Circuit Tails-Receptacle Only.The new low insertion force, front-insertable, front-removable #22 socket contacts with .025(6.35) dia., PC tails are now availble for use in the BKAF non-environmental receptacle version only.These contacts can be sold separately or they can be supplied with a connector (see How to Order). Use part numbers shown in the table on the right when ordering separately.BKAD/F Solder Post, Power Pin Contacts (Captive)-Receptacle Only.Contacts are captivated between two unbonded insulator halves.BKAF Solder Post Pin Contact Front Release Front Release Pin Contacts Size 20 and 16The new low insertion force, front-insertable, front-removable #22 socket contacts with .025(6.35) square wire wrappable tails are now available for use in the BKAF non-enviornmental receptacle version only.These contacts can be sold separately or they can be supplied with a connector (see How to Order). Use part numbers shown in the table on the right when ordering separately.*Applies to BKAF 13W2 and 5W2 inserts only*Consult facotry for other available lengthsSize 5 Coax Contact (Rear insertable/removable)Size 12 Shielded Contact (Rear insertable/removable)Size 1 Modified Coaxial Contacts (4W4 Layout Only)Crimp Center Contact-Conforming to ARINC 600Part Number Style Solder Type Replacement Termination KitsCrimpTypeCoax Coax Replacement Termination KitsCable Accommodation Part Number Style Solder Type CrimpTypeCable Accommodation RG316 DS RG142Various 349-1051-002349-1044-000349-1042-000Straight Straight SMA Adapter 320-1066-008320-1066-007N/AN/ARG214AA-5886RG393ECS 311201AA-5887AA-5888RG142Various 349-1043-001349-1048-000349-1051-000349-1046-000349-1049-000349-1050-000349-1047-000349-1047-001Straight Straight Straight Straight Straight Straight Straight TNC Adapter 320-1066-000320-1066-002320-1066-003320-1066-001320-1066-004320-1066-005320-1066-006320-1066-016320-1066-018320-1066-019320-1066-017320-1066-013320-1066-014320-1066-015----Plug ConnectorCustomer Use Drawings:All Coax contacts (except 349-1047-001) customer use drawing #349-0000-305Crimp termination kits: Customer use drawing #320-0000-305Solder termination kits: Customer use drawing #320-0000-304Receptacle ConnectorCustomer Use Drawings:Coax contacts 349-1051-002 and 349-1044-000 are located on cusomter use drawing #349-0000-304Coax contacts 349-1042-000 is located on cusomter use drawing #320-1042-000Sizes 1 Coax Contacts (71W1 layout only)Sizes 1 Coax Contacts (To be used with connectors containing 71W1A, 71W1B and 2W2 insert modifier-"M")Same standard coax contacts as used in ITT Cannon's DPX (ARINC 404) connector series.Designed to be interchangeable with contacts made by other manufacturers.Receptacle Connector Plug ConnectorSize 8 Coaxial ContactsSize 8 Twinax ContactsSize 8 Ground ContactsPlug ConnectorReceptacle ConnectorPlug ConnectorReceptacle ConnectorReceptacle ConnectorPlug ConnectorContact Type Socket Part Number *Engagement **TerminationShort Long Crimp RR-RR X -----349-1087-000-----349-1087-001349-1084-000349-1084-001349-1084-002349-1084-003349-1086-000349-1086-001349-1006-000349-1081-000----X X 349-1007-000349-1080-000349-1080-001349-1080-002349-1080-003349-1082-000349-1082-001349-1088-000031-3300-000--X 8, 10 AWG030-3306-000030-3306-001030-3676-000---X X 8, 10 AWG8, 10 AWG8, 10 AWGX X -X -X -X -X ----X XX-X XX-X X X X X X X X X XXX XXX X X X X Crimp FR-RR Solder .250 (6.35)FR-FR .375 (9.52)RF CableNumberContact Type Socket Part Number *Engagement **TerminationShort Long Crimp RR-RR Crimp FR-RR FR-FR .250 (6.35)Solder .375 (9.52)RF CableNumberContact Type Socket Part Number *Engagement **TerminationShort Long Crimp RR-RR Crimp FR-RR Solder .250 (6.35)FR-FR .375 (9.52)RF CableNumberContact Type Socket Part Number *Engagement **TerminationShort Long Crimp RR-RR Crimp FR-RR Solder .250 (6.35)FR-FR .375 (9.52)RF CableNumberContact Type Socket Part Number * The electrical engagement of "Long" contacts is .150 (3.81) greater than the electrical engagement of "Short" contact.**RR-RR indicates rear release, rear removal.FR-RR indicates front release, rear removal.FR-FR indicates front release, front removal.*Engagement **TerminationShort Long Crimp RR-RR Crimp FR-RR Solder .250 (6.35)FR-FR .375 (9.52)WireSizeContact Type Socket Part Number *Engagement **TerminationShort Long Crimp RR-RR Crimp FR-RR Solder .250 (6.35)FR-FR .375 (9.52)WireSizeAdams-Russell Co. Inc.FC11ZAdams-Russell Co. Inc.FC14ZAdams-Russell Co. Inc.FC11ZAdams-Russell Co. Inc.FC14ZM17/176-00002Tensolite Co.24463/9 B017X-2 (LD)Tensolite Co.24463/9 B017X-2 (LD)Tensolite Co.24463/9 B017X-2 (LD)Tensolite Co.24463/9 B017X-2 (LD)M17/176-00002Sealing Plugs-BKAE Environmental Connnectors OnlyFiller Plugs-BKAD Non-Environmental Connectors OnlyCavity ReducerDust Caps#5 Coax to #12 ContactCavity reducers are available when additional circuits are required for siz 12 power contacts. Thesereducers, having the internal configuration of size 12 power contact, are inserted into the size 5 coaxialinsulator cavity to create size 12 power contact cavity.025-1121-001025-1122-001025-1123-001025-1124-001PinP/N 021-8756-000SocketP/N 021-8757-000Note: Supplied as standard for BKA product line only.BKAD 1-A & B-PlugBKAD 1-C-PlugBKAD 2&3-A & B-PlugBKAD 2&3-C-Plug025-1155-001025-1156-001025-1157-001025-1158-001BKAD 1-A&B-ReceptacleBKAD 1-C-ReceptacleBKAD 2&3-A & B-ReceptacleBKAD 2&3-C-ReceptaclePart Number Part NumberDescription DescriptionP/N 225-0090-000Material: Teflon(All others thermoplastic)P/N 225-0099-000Material: Teflon(All others thermoplastic)BKAF P/N 225-1058-000(Size 22 - Black)(See Customer Use Drawing for details)Conductive dust caps protect againststatic electricity.Replaceable InsertsPart NumberSocket AssemblyPin AssemblyClassBKAD BKAE BKAE BKAD BKAE BKAD BKAE BKAF BKAE BKAD BKAE BKAF BKAD BKAE BKAD BKAE BKAF BKAD BKAE BKAD BKAE BKAE BKAE BKAE BKAD BKAE BKAF BKAD BKAE BKAF BKAD BKAE BKAF BKAD BKAE BKAF BKAD BKAE BKAF BKAD BKAE BKAF BKAE BKAD BKAE BKAF BKAD BKAE BKAD BKAE BKAF 144-2944-000144-2944-000143-1156-001177-1000-002177-1000-002143-1912-000143-1912-001143-1141-000143-1154-001228-1026-002228-1026-001N/A228-1027-002228-1027-001143-1908-000143-1908-001143-1142-000143-1173-000143-1173-001143-1159-001143-1097-005143-1171-001143-1167-001143-3714-003143-1910-000143-1910-001N/A143-1958-000143-1958-002N/A143-2085-001143-2085-000N/A143-1113-000143-114-000N/A143-3877-000143-3879-000N/A143-2015-000143-2015-001N/A143-1182-000N/A143-1165-001N/A143-1150-002143-1150-001143-1906-000143-1906-001N/A144-2945-000144-2945-000143-1157-001177-1001-004177-1001-004143-1913-000143-1913-001N/A143-1155-001228-1012-003228-1012-001228-1015-001N/A228-1014-002143-1909-000143-1909-001N/A143-1174-000143-1174-001N/A143-1098-005143-1172-001143-1170-001143-3715-003143-1911-000143-1911-001143-2065-000143-1960-000143-1960-002143-2090-000143-2086-001143-2086-000143-2066-000143-1111-000143-1112-000143-1118-000143-3878-000143-3880-000143-1178-000143-2016-000143-2016-001143-2067-000143-1183-000143-1166-002143-1166-001143-1177-000143-1158-002143-1158-001143-1907-000143-1907-001143-2068-000Layout2W2**A4W4**5W266T610T1013W230T2344059*60-#20**60-#22**71W171W1A*71W1B85100110120T2121150Consult factory for Insert Part Numbers not listed.*Modified 71W1 insert to be used with connectors containing 71W1 insert modifier "M"**"Pin Inserts' accept receptacle coax contacts. "Socket Inserts" accept plug coax contacts.AR INC 600 R ack and Panel Connectors B K AD/E/F Cross Reference-Part Number/Customer-Use DrawingCOMPONENT PART NUMBER CUSTOMER USE DRAWING NUMBER COMPONENT PART NUMBER CUSTOMER USE DRAWING NUMBER COMPONENT PART NUMBER CUSTOMER USE DRAWING NUMBER030-1975-009030-1975-010030-2259-000030-2273-000030-2280-000030-2286-000030-2356-000030-2357-000030-2358-000031-1113-009031-1113-010031-1287-000031-1302-000031-1303-000031-1308-000031-1351-000031-1351-001031-1351-002031-1351-003031-1352-000031-1252-000031-1252-002031-1352-003143-1908-000143-1908-001143-1909-000143-1909-001143-1910-000143-1910-001143-1911-000143-1911-001143-1912-000143-1912-001143-1913-000143-1913-001143-1958-000143-1958-002143-1960-000143-1960-002143-2015-000143-2015-001143-2016-000143-2016-001143-2065-000143-2066-000143-2067-000143-2068-000143-2085-000143-2085-001143-2086-000143-2086-001249-1521-002249-1522-009249-1522-010249-1554-002249-1604-003249-1604-004249-2201-000249-2202-000249-5027-013249-5027-015249-5027-016320-0051-000320-1066-000320-1066-001320-1066-002320-1066-003320-1066-004320-1066-005320-1066-006249-1521-002249-1522-010249-1522-010249-1554-002249-1604-003249-1604-004249-1521-002249-1522-010249-5027-013249-5027-007249-5027-0161250Y 320-000-305025-1121-001025-1122-001025-1123-001025-1124-001025-1155-001025-1156-001025-1157-001025-1158-001025-0000-054(Conductive Only)025-0000-055(Conductive Only)225-0000-014225-0094-000225-0095-000225-0096-000225-0097-000225-0098-000225-0099-000225-1058-000225-0072-000225-0090-000225-1013-000225-1014-000225-1015-000225-0000-006225-0090-000225-0000-008143-0000-081143-0000-077143-0000-080143-0000-079143-0000-0781247Y143-0000-079249-1521-000249-1522-000249-1522-002249-1554-000249-1604-000249-1604-001249-1604-002249-1882-0001250Y 249-5027-008249-5027-017249-5027-000249-5027-007349-0000-306249-1521-000249-1522-000249-1522-002249-1554-000249-1604-000249-1604-001249-1604-002249-1882-000249-1882-002249-1885-002249-5027-008249-5027-017249-5123-000249-5123-001349-1053-000349-1053-001349-1053-002349-1053-003349-1053-0043491053-005349-1053-006349-1053-007349-1053-008349-1053-009030-1975-009030-1975-010030-2259-000030-2273-000030-2280-000030-2286-000030-2356-000030-2357-000030-2358-000031-1113-009031-1113-010031-1287-000031-1302-000031-1303-000031-1308-000031-0000-343031-0000-344021-0144-000021-0144-001021-0144-002021-0144-003021-0144-004021-0144-006021-0144-008021-0144-011021-0144-000021-0144-001021-0144-002021-0144-003021-0144-004021-0144-006021-0144-008021-0144-011349-0013-000349-0014-000349-0015-000349-0016-000349-1003-000349-1009-000349-0000-000349-0000-001349-0000-002349-0000-001349-000-301249-1767-000249-1767-001249-1768-000249-2203-000249-1767-000249-1767-001249-1768-000249-2203-000143-1906-000143-1906-001143-1907-001143-1907-001143-0000-079Contacts Replacement Coax Termination Kit Dust CapsFiller PlugsSealing PlugsReplacement Coax Body Assembly Size #1 Coax Contacts Size #5 Coax Contacts Size #12 Shielded Contact Replaceable Inserts For part numbers not listed, consult ITT Cannon for applicalbe customer-use drawing.ARINC 600 Rack and Panel Connectors BKAD/E/F ARINC 600 Connector Engaging SequenceMating Sequence Flange Position With:#22#221. Varies; See Mil-Spec. (#5 Coax)2. Size 1 only.3. Flush head screws are not permitted for connector mounting as they would position connector incorrectly.4. Dimension 7 was calculated to provide clearance for - MCU backplate mat'l thickness of 2.5 mm (.10 in).- Rack backplate mat'l thickness of 2.5 mm (.10 in).- Connector mounting pan head screws, MCU 2.0 mm (.08 in).- Tolerance allowance - 3.2 mm (.13 in.) rack 2.0 mm (.08 in.)Total - 12.2 (.50 in) (minimum).1.110 (28.19)1.073 (27.25).800 (22.32).748 (18.99).805 (20.44).741 (18.82)1.012 (25.70).949 (24.10)1.008 (23.60).953 (24.20).642 (16.30).547 (13.89).649 (16.48).553 (14.04).728 (18.49).818 (20.77).772 (19.60).692 (17.57).618 (15.70).578 (14.68).522 (13.26).488 (12.40)Shells Initially Engaged Contacts EnteringMating Insulator#22#20#16#12"0" Ring Engagement (BKAE Only)Shells Fully Mated Contacts ElectricallyEngaged#22#20#16#12Flange Spacingin. (mm)2245176。
3M 面板接头.100 × .100 高温 N4600 系列说明书
.25 Ref [6.4]
.17 [4.3]
A
Optional Ejector Latch
.243 Ref [6.17]
.525 [13.34]
.100 Ref [2.54]
.025 Sq Typ [0.64]
CO 06 NotchA
(See Table 1 & Note 1)
IS 1 .100 Typ Ref D ECO [2.54]
Moisture Sensitivity Level: 1 (per J-STD-020C)
UL File No.: E68080
3
Electronic Solutions Division Interconnect Solutions
3M is a trademark of 3M Company. For technical, sales or ordering information call
Plating suffix: blank = tin-lead solder tails (RIA E3 & C2 Apply) RB = matte tin solder tails (RIA E1 & C1 Apply)
Ejector Latch
(May be ordered separately for use with N46XX-20XX-XX version)
TS‑0168-E Sheet 3 of 3
3M is a trademark of 3M Company. For technical, sales or ordering information call
800-225-5373
Body Style: 0 = with mounting ears 1 = without mounting ears
Omega MWTC Wireless Smart Thermocouple Connector S
ߜ Available in Types J, K, T, E,R, S, B, C or N ThermocoupleCalibrationߜ Built-In Cold JunctionCompensation andLinearizationߜ Model MWTC-REC1 ReceiverWorks with Multiple WirelessRemote Connectorsߜ Low Power Operation andSleep Mode For ExtendedBattery Lifeߜ Each Wireless ConnectorTransmits ThermocoupleTemperature and AmbientTemperature in Real Timeߜ Free Software Converts YourPC Into a Multi-Channel ChartRecorder or Data LoggerOmega’s new MWTC WirelessSmart Thermocouple ConnectorSeries features stand-alone,compact, battery poweredthermocouple connectors thattransmit measurement data back toa mating receiver up to 90 m (300')away. Each unit is factory set as aType J, K, T, E, R, S, B, C, or Ncalibration connector. Whenactivated the connector will transmitreadings continuously at pre-settime interval that was programmedby the user during the initial setup.Each unit measures and transmits:thermocouple input reading andconnector ambient temperature to areceiver and is displayed on the PCscreen in real time using the freeprovided software. When used withreceiver model MWTC-REC1 datafrom multiple wireless thermocoupleconnectors can be received anddisplayed. Each unit includes freesoftware that converts your PC intoa strip chart recorder or data loggerso readings can be saved and laterprinted or exported to a spreadsheet file. When used with matingtransceiver model MWTC-REC2,wireless data from one connectorcan be re-transmitted as athermocouple signal back out of thereceiving connector by a wiredconnection.Miniature Wireless Thermocouple ConnectorsThe Smart Connector™MWTC-K wirelessconnector, $79,shown smallerthan actual size.MWTC-K, $79, shown actual size.MWTC-REC1,USB receiver,$116, shownsmaller thanactual size.MWTC SeriesStarts at$P l u g Y o ur P r o b eI n t oA S m a r tC o n n e c to r T oM a k e AS m a r t Sens o rCovered by U.S. andInternational Patents andpending applicationsPATENTEDThermocouple Types:(Factory Set) J, K, T, E, R, S, B, C or NThermocouple Measurement Range:J: -100 to 760°C (-148 to 1400°F)K:-100 to 1260°C (-148 to 2300°F)T:-200 to 400°C (-328 to 752°F)E:-200 to 1000°C (-328 to 1832°F)R:260 to 1760°C (500 to 3200°F)S:260 to 1760°C (500 to 3200°F)B:870 to 1820°C (1598 to 3308°F)C:0 to 2315°C (32 to 4200°F)N:-100 to 1260°C (-148 to 2300°F)TC Measurement Accuracy:J, K:±0.5% of reading or ±1.0°C (1.8°F), whichever greaterT, E, N:±0.5% of reading or ±2.0°C (3.6°F), whichever greaterR, S, B, C:±0.5% of full scaleTC Measurement Resolution:Type J, K, T, E, N:1°C/1°FType R, S, B, C:1°C/1°FCold Junction Compensation:-10 to 70°C (14 to 158°F)Thermocouple Connection:Patented universal femaleaccepts both standard male (OSTW Series) or miniature male(SMPW Series) mating connectorOperating Environment:-10 to 70°C (14 to 158°F)Computer Interface:USB (one interface cable includedwith receivers)Transmit Sample Rate:Programmable from1 sample/15 minute to 1 sample/every2 secondsRadio Frequency:ISM 915 mHz or ISM 868 mHzRF Output Power:10dBm (10 mW)Range of RF Link:Up to 90 m (300'):Outdoor line of sightUp to 45 m (130'):Indoor/urbanSoftware:Requires Windows®2000, XP,or Vistaoperating system (included)MWTC-REC1This compact multi-channel wirelessUSB receiver works with all MWTCwireless thermocouple connectors.When connected to your PC, readingsfrom multiple connectors can bedisplayed, charted and saved inreal-time with the FREE user software.MWTC-REC1, $116,shown smaller thanactual size.Battery:One 3.6 V lithium, 650 mA capacity(AAA) (included)Battery Life (Typical):1 year at 1 sample/minute reading rate @25°C (77°F)Data Transmitted to Receiver:Thermocouple reading andconnector ambient readingDimensions:76 L x 25.4 W x 13 H mm (3 x 1 x 0.5")Enclosure:Plastic (Nylon)Note:Because of transmission frequency regulations, theseproducts may only be used in the United States and Canada(915 mHz models) or Europe (868 mHz models).*Insert connector Type J, K, T, E, R, S, B, C or N**Insert ISM frequency “915”for USA and Canada, “868”for Europe†Insert output type “MA”for 4 to 20 mA, “V1”for 0 to 5 Vdc, “V2”for 0 to 10 Vdc, or Thermocouple J, K, T, E, R, S, B, C or NUSA, Canada Ordering Examples: Two MWTC-K-915, 915 mHz wireless Type-K thermocouple connector/transmitters, MWTC-REC1-915multi-channel 915 mHz receiver, $79 + 79 + 116 = $274.MWTC-K-915,915 mHz wireless Type-K thermocouple connector/transmitter,MWTC-REC2-MA-915,one-channel 915 mHz transceiver with 4 to 20 mA output, $79 + 109 = $188.Europe Ordering Examples: Two MWTC-K-868,868 mHz wireless Type-K thermocouple connector/transmitters, MWTC-REC1-868,multi-channel 868 mHz receiver, $79 + 79 + 116 = $274.MWTC-K-868,868 mHz wireless Type-K thermocouple connector/transmitter,MWTC-REC2-MA-828,one-channel 868 mHz transceiver with 4 to 20 mA output, $79 + 109 = $188.operator’s manual.Each connector includes a free 1 m (40")Type K insulated beaded wire thermocouplewith subminiature connector and wire spool caddy.(subminiature connector).(standard connector).Free Thermocouple Included!CANADA www.omega.ca Laval(Quebec) 1-800-TC-OMEGA UNITED KINGDOM www. Manchester, England0800-488-488GERMANY www.omega.deDeckenpfronn, Germany************FRANCE www.omega.frGuyancourt, France088-466-342BENELUX www.omega.nl Amstelveen, NL 0800-099-33-44UNITED STATES 1-800-TC-OMEGA Stamford, CT.CZECH REPUBLIC www.omegaeng.cz Karviná, Czech Republic596-311-899TemperatureCalibrators, Connectors, General Test and MeasurementInstruments, Glass Bulb Thermometers, Handheld Instruments for Temperature Measurement, Ice Point References,Indicating Labels, Crayons, Cements and Lacquers, Infrared Temperature Measurement Instruments, Recorders Relative Humidity Measurement Instruments, RTD Probes, Elements and Assemblies, Temperature & Process Meters, Timers and Counters, Temperature and Process Controllers and Power Switching Devices, Thermistor Elements, Probes andAssemblies,Thermocouples Thermowells and Head and Well Assemblies, Transmitters, WirePressure, Strain and ForceDisplacement Transducers, Dynamic Measurement Force Sensors, Instrumentation for Pressure and Strain Measurements, Load Cells, Pressure Gauges, PressureReference Section, Pressure Switches, Pressure Transducers, Proximity Transducers, Regulators,Strain Gages, Torque Transducers, ValvespH and ConductivityConductivity Instrumentation, Dissolved OxygenInstrumentation, Environmental Instrumentation, pH Electrodes and Instruments, Water and Soil Analysis InstrumentationHeatersBand Heaters, Cartridge Heaters, Circulation Heaters, Comfort Heaters, Controllers, Meters and SwitchingDevices, Flexible Heaters, General Test and Measurement Instruments, Heater Hook-up Wire, Heating Cable Systems, Immersion Heaters, Process Air and Duct, Heaters, Radiant Heaters, Strip Heaters, Tubular HeatersFlow and LevelAir Velocity Indicators, Doppler Flowmeters, LevelMeasurement, Magnetic Flowmeters, Mass Flowmeters,Pitot Tubes, Pumps, Rotameters, Turbine and Paddle Wheel Flowmeters, Ultrasonic Flowmeters, Valves, Variable Area Flowmeters, Vortex Shedding FlowmetersData AcquisitionAuto-Dialers and Alarm Monitoring Systems, Communication Products and Converters, Data Acquisition and Analysis Software, Data LoggersPlug-in Cards, Signal Conditioners, USB, RS232, RS485 and Parallel Port Data Acquisition Systems, Wireless Transmitters and Receivers。
Type-C连接器商品说明书
Material declaration MATERIAL
DESCRIPTION
-
HIGH TEMP[Black]
COPPER ALLOY【G/F】 Au:15μ” PLATING OVERALL;[t=0.12mm]銅鎳硅合金
Universal Serial Bus Connectors
Technical parameter
PROJECT
╲ ╲
LEVEL Contact Rating
Electrical
Initial Contact Resulation Resistance
Withstand Voltage
A10
SSRXn2
SuperSpeed RX differential pair
B3
Positive half of second
A11
SSRXp2
SuperSpeed RX differential pair
B2
A12
GND
Ground return
B1
Signal NAME GND
SSRXp1
SSRXn1 V BUS SBU2
COPPER ALLOY【G/F】 Au:15μ” PLATING OVERALL;[t=0.12mm]銅鎳硅合金
STAINLESS【G/F】
STAINLESS STEEL(t=0.15mm)
STAINLESS【G/F】
STAINLESS STEEL/ Ni PLATING(t=0.10mm)
STAINLESS【G/F】
Durable Performance
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
COPYRIGHT © CMPTER ELECTRONICS 2010Cable ConnectorsReceptacles With Solder EndProtective Caps
N CONNECTORS
... A Vital Part of Connection WorldCMPTERType N 50 Ohm Coaxial Connectors
#45 ZhongShan East Road, ZhenJiang 212003, JiangSu, ChinaTel : +86-511-8443 6131Fax : +86-511-8698 8811Website: www.cmpter.com
Email : sales@cmpter.com
CMPTER1DESCRIPTION
CONTENTSDescription ..............................................................................
Technical data ...........................................................................Interface dimensions ....................................................................Cable connectors .......................................................................Receptacles with solder end ............................................................PCB connectors .........................................................................Protective cap ...........................................................................Assembly instruction ....................................................................Mounting hole ........................................................................... 211234
1516
1114
The development of the Type N connector by the United States Army/Navy ran directly parallel to theesca-lation of U.S. involvement in WWII. It was finally released in 1942, shortly after the U.S. officially ment field and join the coaxial cable of the radio frequency extensively entered the war, and since that time it has been a staple in RF and Microwave applications all over the world.
Due to N type connectors joins by one whorl, it has the characteristic of raliable and strong ant-vibrationnature, machinery and electric performance finely. It is used in vibration and environment abominable radio equipment of terms and instrument and ground launch system join the coaxial cable of the radion frequency extensively.Type N INTERFACE
#45 ZhongShan East Road, ZhenJiang 212003, JiangSu, ChinaTel : +86-511-8443 6131Fax : +86-511-8698 8811Website: www.cmpter.com
Email : sales@cmpter.com
CMPTER2Interface dimensions conformable to the standards: International: IEC61169-16Europe: CECC 22210USA: MIL-STD-348A/304,
IP rating (interface, mated) IP68
LETTERmminchLETTERmminchmin.max.min.max.min.max.min.max.A0.131.03.005.13A9.059.19.356.362B2.803.56.110.140B4.755.25.187.207C5.335.83.210.229C1.201.95.047.077D12.016.066D4.45.1.173.201E4.545.39.179.212E6.89.268.354F4.054.20.159.165F10.911.2.429.441G10.2310.43.403.411G DIA6.987.02.275.276H DIA8.278.37.326.329H DIA8.038.13.316.320J DIA16.116.2.634.638J DIA8.538.73.336.344K DIA20.921.823.827K DIA15.6515.85.616.624L DIA3.013.05.118.120L DIA3.013.05.118.120M DIA1.631.67.064.066TECHNICAL DATA
#45 ZhongShan East Road, ZhenJiang 212003, JiangSu, ChinaTel : +86-511-8443 6131Fax : +86-511-8698 8811Website: www.cmpter.com
Email : sales@cmpter.com
CMPTER3ELECTRICAL DATAImpedanceFrequency rangeDielectric withsanding voltageV.S.W.R.
50 OhmDC 0 — 11 GHz2,500 volts rmsstraight connectors: 1.3 max 0-11 GHz; right angle connectors: 1.35 max 0-11 GHz
Insulation resistance
Contact resistance RF leakage≥ 5*1000 MΩCenter Contact 1.0 mΩ Outer Contact 1.0 mΩ-90 dB minimum at 3 GHz
MECHANICAL DATACenter Conductor Cale AffixmentMatingAssembly Torque (body/clamp nut)
Crimps: hex braid crimp;Clamps:screw-thread nut and braid clampCrimp: crimp or solder;All others: solder only5/8-24 threaded coupling18/22 lb-ft (25/30 N-m)
Braid/Jacket Cable Affixment
ENVIRONMENTALThermal shockMoisture resistanceCorrosion
TFE: -65°C to +165°CMIL-STD-202, method 107, test condition A-1MIL-STD-202, method 106MIL-STD-202, method 101, test condition B
Temperature Range
MIL-STD-202, Method 204, Condition DVibration
MATERIAL DATAFemale contactGasketCrimp Ferrule
Brass, silver or gold platedPhosphorous bronze or beryllium copper, silver or gold plated Other Metal Parts Brass Silicone rubberCopperMale Contact