模具英语
模具专业术语英语
模具专业术语英语
模具专业涉及许多专业术语，在英语中对应的词汇如下：
1. Mold/Mould: 模具
2. Die: 模具，尤指金属冲压模
3. Cavity: 模穴
4. Core: 模芯
5. Runner: 喷嘴，注塑道
6. Gate: 浇口，进料口
7. Ejector Pin: 顶针，用于将制品从模具中推出
8. Injection Molding: 注塑成型
9. Blow Molding: 吹塑
10. Compression Molding: 压缩成型
11. Extrusion Molding: 挤出成型
12. Casting: 铸造
13. Hot Runner: 热流道系统
14. Cooling Channel: 冷却通道
15. Draft Angle: 脱模锥度
16. Shrinkage: 收缩率
17. Surface Finish: 表面处理/光洁度
18. Undercut: 模具槽，模具凹槽
这些词汇在模具制造和加工过程中经常使用，涵盖了模具设计、制造和加工等方面的专业术语。
模具英语专业术语
模具英语专业术语模具的分类:冲压模(五金模): stamping die分离模: cutting die成形模: forming die塑胶模: plastics mold注射模: injection mold压缩模: compression mold铸塑模: transfer mold吹塑模: blow mold吸塑模: suck mold铸造模: casting die砂型铸造: sand casting压铸模: die casting锻造模: forging die塑胶模具术语一、入水：gate进入位(入水点)：gate location水口形式：gate type大水口(侧浇口): edge gate潜水口: sub-gate薄膜式水口: film gate牛角式潜水口: banana gate扇形水口: fan gate环形水口: ring gate二次水口:细水口：pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter直接水口: direct gate二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形(整圆/半圆)流道：round(full/half) runner矩形流道: rectangle runner梯形流道: trapezoid runnerU形流道: U shape runner流道电脑分析(模流分析)：mold flow analysis流道平衡: runner balance热嘴：hot sprue/tip热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line plug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socket 四、模具零件：mold components 三板模(细水口模)：3-plate mold二板模(大水口模)：2-plate mold热流道模具: hot-runner/manifold mold叠层模: stacked mold边钉/导边：leader pin/guide pin边司/导套：guide pin/guide bushing直导套：shoulder guide bushing有托导套：straight guide bushing中托司：ejector guide bush中托边：ejector guide pin回针: return pin面板: top clamp plateA板: A plate推板：stripper plateB板: B plate托板：support plate方铁: spacer block加高方铁: higher spacer block顶针固定板：ejector retainner plate顶针板：ejector plate底板: bottom clamp plate螺丝：screw杯头螺丝: socket cup head screw平头螺丝: socket flat head screw机米螺丝:外六角头螺丝: bolt栓打螺丝(等高螺丝)：S.H.S.B管钉：dowel pin开模槽：ply bar socket内模管位(模仁互锁)：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：sleeve ejector pin缩呵：movable core,return core, core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位（滑块）：slide行位扣:镶件：insert压座/斜鸡：wedge耐磨板/油板：wear plate压条：gib撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈(法兰)：locating ring锁扣(模锁)：latch扣鸡：parting lock set推杆：push bar顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring型腔(前模仁): cavity型芯(后模仁): core镶针：insert pin销子(销钉)：dowel pin波子弹弓：ball catch喉塞(堵头): pipe plug锁模块：lock plate斜顶杆：angle ejector rod斜顶针：angle from pin尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边(斜导柱)：angle pin油缸: hydraulic cylinder液压马达: hydraulic motor齿轮: gear轴承: bear术语：terms承压平面平衡：parting surface support balance分模面排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes with ejector pin料位出上/下模：part from cavity (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate. 不准用镶件：Do not use (core/cavity) insert用铍铜做镶件：use beryllium copper insert初步模图设计：preliminary mold design正式模图设计：final mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模(粘模)：sticking顶白: stress mark热膨胀：thero expansion缩水: shrinkage物料表: BOM原料: raw materials物料: materials工程试模材料: material for engineering mold testing成品: finished product半成品: semi-finished product公差：tolorance铜公(电极)：copper electrode射料不足: short shot缺口: nick瑕疪(斑点): speck亮斑: shine银纹: splay焦痕: gas mark起鳞: delamination冷块: cold slug导色: blush沟槽;凿槽: gouge段面咬花: satin texture证示线: witness line专利: patent沙砾: grit细粒: granule=peuet=grain抽粒机: grit maker缓冲: cushion不锈钢: stainless steel镁铝合金: magnalium镁金属: magnesium钣金: metal plate车/车床: lathe铣床/铣床: mill刨/刨床: plane磨/磨床: grind钻/钻床: drill镗: boring气泡: blinster版次: revision备注: remark生产确认: production control confirmation 初审: checked by核准: approved by部门: department电镀: plate成型: molding样品: sample雕刻: engrave蚀纹: texture加硬: harden热处理: heat treatment淬火: quenching回火: tempering退火: annealing碳化: carbonization铬酸处理: chromate阳性处理: anodize氮化: nitrifying。
模具英语
替换镶件：Interchangeable Mold Inserts。
模芯：Parting Core。
侧抽芯：Side Action 。
脱螺纹：unscrew。
excluding metallic parts price：不包括五金件价格。
Subtract to button up, convenient mold：反向弹出：reverse eject，硬度：hardness 。
牛角进胶：cashew gate 。
runner system：浇道系统。
stress crack：应力电裂。
orientation：定向。
sprue gate；射料浇口。
直浇口：nozzle射嘴。
slag well：冷料井。
bronze：青铜。
brass；黄铜。
prototype mold；手办模。
side gate：侧浇口。
edge gate：侧缘浇口。
tab gate：搭接浇口。
film gate：薄膜浇口。
flash gate：闸门浇口。
slit gate：缝隙浇口。
fan gate：扇形浇口。
dish gate：因盘形浇口。
Mold working automatic 模具自动生产 overmolding 包胶模H=F=1/2t~1/5t 。
T=2.5~3.5mm 。
diaphragm gate：隔膜浇口。
ring gate：环形浇口。
Sub gate：潜入式浇口。
tunnel gate：隧道式浇口 pin gate：针点浇口。
晒纹Texturing。
方铁;Spacer Block . 顶针板:Ejector Plate。
There are under cut at this area of part 零件这处有倒扣，can not be released 不能脱模 runner shut off 转水口cavity and core direct cut on A.B-plate 料位在A,B板上原身出。
2 stage ejection 二次顶出interchangeable cavity,core and sliders for each part互换前后模和行位生产每一个产品。
模具英语词汇大全
汽车冲压模具英语词汇Die / Tool= 模具Prog. Die=progressive die 级进模Casti ng die=W 造模Part=ffi 件Die material=制模材料Tool desig门=模具设计Strip desig门=料条设计Tool desig n approval^ 具设计审核Tool desig n modificatio n/revisio n=模具设计更改Tool parts design （detail） = 模具钣件设计（详细）FMC Make=保丽龙制作modification= 更改Check & measured查& 测试Machining= 机器加工Large m a c h i n i n g =在大型机器上加工上下模架（铣、车等）Small machi ning二在小型机器上加工模块等Assembly 二组立NC Machining=NC 雕刻加工Fitti ng=研磨组立Spott ing二合模Dowel pi n=定位销Assemble gas spri ng安装氮气缸Adjustme nt=调试Lower trim steels=下刃块Sectio门=冲头断面Trim pun ch=切刃冲头jack screw hole=起重［千斤顶］螺旋孑L Die set, lower plate=T 模架Die set, upper plate=h 模架Ball beari ng guide posts and bush in §$=球形滚珠导柱和轴套Cage=®Rigidity= 强度Thi n=薄Using material thickness radii where sharp corners are shown on the part reduces the occurrence of chipped punch or die corners in the tool. =在尖角处使用与材料厚度一样的R 角减少冲头碎裂或模具中有“刀口”Heeled die sets, internally heel form & trim sections^箱根的模架，成形与切刃冲头带导引Con structio n method^ 构方法Lower die trim in serts=下模切刃块Lower trim in serts retai ner=T 模切刃块承盘Assemble in serts=fi 立镶块Punch stripp ing platesh 中头压料板Trim punch back ing plates=切刃冲头背板Stripper wi ndow in serts=# 条窗户镶块Die tryout=试模Cushi ng stroked 冲行程Guide lift pin= 导引升降销Stamp partsh 中钣件Run off parts=中钣件Hit parts=冲钣件Lifters=提升器Coil=卷材Guide block 二导弓I块Guide the coil through the tool=# 引卷材layout in spectio n=全尺寸检验Die in specti on & approval=模具检查和审核delivery=发货Rejected* 收Scrapped=报废Rework=返工stop block=停止块Hydro form液压成形Shear=K 切Sen sor=ft 感器Stretch web=S 伸网Layout the parts=S 计钣件Preced ing into the desig n继续设计Guide the coil through the tool=# 弓I卷材Check ing aid /check ing gage=检具Jig=夹具Fixture=夹具Ball beari ng guide posts and bush in gs= 球形滚珠轴套Guide post=导柱Bushings二导套Using material thickness radii where sharp corners are shown on the part reduces the occurre nee of chipped punch or die corners in the tool.=在尖角处使用与材料厚度一样的R 角减少冲头碎裂或模具中有“刀口”Heeled die sets, intern ally heel form & trim sectio ns=带箱根的模架，成形与切刃冲头带导引Gra nite Tabled 岗岩平台Plotter=.描绘器,图形显示器,绘图器,坐标自记器，标图员Belt San der=# 磨机Metal Cutti ng Ba nd Saw^ 式带锯床Bla nchard Grin der=大型平面磨床Stretch carriers=S 伸运送装置Punch stripp ing platesh 中头压料板Trim punch back ing plates=切刃冲头背板Stripper wi ndow in serts=M 条窗户镶块Heel plates=W 托Prepare for delivery^® 备发货Key=键For locati ng reta iner blocks^ 盘键For holdi ng butt ons or pilots=冲母座或导销键For fixed heel or positive stop=B 根键Con structio n method=S 构方法Manual Surface Grin der=手动平面磨床Spott ing red=合模用丹红Layout ink=试模用蓝墨水Masking tape=M色不透明胶带(遮蔽胶带) Pliers=尖嘴钳，老虎钳Crese nt wren ch=可调扳手Pump pipe=泵管CMM=三次元测量仪Symmetric=对称的The axis of symmetry^ 称轴Tech nical^ 术上的Diago nal=对角线One two three block” 二三模块Adjustable parallels^ 调平行块Stop block=阻止块Backi ng Plate=背板Shoulder Bolt=肩头螺丝(Stripper bolt)Keeper Block=行程块Corner Guide Block=# 块Dowel pi n=定位销Joe Blocks=ft 密量块Whirly Gig=筒夹式冲子成形器Chamfer Tools= 到角刀具组Angle Plate=L形直角座Gage Pins=^寸塞规Si ne Plate (mag netic)=E 弦磁台Flute End Mill=硬质合金钢铣刀Mill Cutter=波纹粗铣刀(标准型) C' bore/ counter bore六角沉头铣刀Radius Dresser=^ 轮修整器Boring Head & Boring Bar=搪孔器、搪刀杆Pin二销Reamer=绞刀Approval 确认Impact wren ch二气动扳手Air pi n=空气销bumper[‘ bQmpE(rn.缓冲器Ven dor [ ‘ ven dE(r)d C:(r)] n.卖主stripper layout=排样图drawing of panel #987415&16=钣件设计图(公差)Arbor =柄轴；心轴Drill chuck=钻夹头Butt on=冲母座Nitroge n Cyli nder=氮气缸Pilot=导销Retai ner二承盘Butt on=冲母座Hose Straps嗽管夹(塑料)Set Screw=S 塞Jig & fixture =夹具Checking fixture二检具Guide Block 二导块Plu nger二柱塞Pierce=?中孑LWear Strip=W 磨板Mating area=ffl立的接触面Accommodate 二适应Wiping hard (very shiny)=过分摩擦闭合[接触](闪光)In crease the die cleara nee betwee n the form steels=®加成形块间隙Cleara nce= 间隙Oil paper 二油纸0-11” Micrometer=0-11 ”千分尺Trim line=切边+/-0.5mm uni ess otherwise specified除非另有规定，否则公差为+/-0.5mmPart tolera nce=R件公差Ball no se=球刀Bore二镗Line tap=攻丝校直Borer二镗刀，镗床Chamfer二倒角Radius=半径Coola nt=切削液Pun ch=^冲头Distribution Blocks=接头座Screw二螺丝Shop# 间Flat Feet Keepers顶料销Ejector Pin=顶出销Spring二弹簧Straight Port Adapter=直管接头Y-205 Hose=< 管(塑料)Short Neck Adapter=S 接头45 Swivel= 45 接头(adjustable) 45。
模具词汇英语翻译汇总特全
模具词汇英语翻译汇总特全burnishingdie挤光模landedpositivemold有肩全压式模具buttondie镶入式圆形凹模loadingshoemold料套式模具center-gatedmold中心浇口式模具loosedetailmold活零件模具chillmold冷硬用铸模loosemold活动式模具clodhobbing冷挤压制模louveringdie百叶窗冲切模compositedies复合模具manifolddie分歧管模具counterpunch反凸模modularmold组合式模具doublestackmold双层模具multi-cavitymold多模穴模具electroformedmold电铸成形模multi-gatemold复式浇口模具expanderdie扩径模offswtbendingdie双折冷弯模具extrusiondie挤出模palletizingdie叠层模familymold反套制品模具plastermold石膏模blankthroughdies漏件式落料模porousmold通气性模具duplicatedcavityplate复板模positivemold全压式模具fantaildie扇尾形模具pressuredie压紧模fishtaildie鱼尾形模具profiledie轮廓模flashmold溢料式模具progressivedie顺序模gypsummold石膏铸模protablemold手提式模具hot-runnermold热流道模具prototypemold雏形试验模具ingotmold钢锭模punchingdie落料模lancingdie切口模raising(embossing)压花起伏成形re-entrantmold倒角式模具sectionaldie拼合模runlessinjectionmold无流道冷料模具sectionaldie对合模具segmentmold组合模semi-positivemold半全压式模具shaper定型模套singlecavitymold单腔模具solidforgingdie整体锻模splitforgingdie拼合锻模splitmold双并式模具spruelessmold无注道残料模具squeezingdie挤压模stretchformdie拉伸成形模sweepingmold平刮铸模swingdie振动模具threeplatesmold三片式模具trimmingdie切边模unitmold单元式模具universalmold通用模具unscrewingmold退扣式模具yoketypedie轭型模模具词汇英语翻译(模具常用成形方式) accuratediecasting精密压铸powderforming粉末成形calendaringmolding压延成形powdermetalforging粉末锻造coldchamberdiecasting冷式压铸precisionforging精密锻造coldforging冷锻pressforging冲锻compactingmolding粉末压出成形rockingdieforging摇动锻造compoundmolding复合成形rotaryforging回转锻造compressionmolding压缩成形rotationalmolding离心成形dipmold浸渍成形rubbermolding橡胶成形encapsulationmolding注入成形sandmoldcasting砂模铸造extrusionmolding挤出成形shellcasting壳模铸造foamforming泡沫成形sinterforging烧结锻造forgingroll轧锻sixsidesforging六面锻造gravitycasting重力铸造slushmolding凝塑成形hollow(blow)molding中空(吹出)成形squeezecasting高压铸造hotchamberdiecasting热室压铸swaging挤锻hotforging热锻transfermolding转送成形injectionmolding射出成形warmforging温锻investmentcasting精密铸造matcheddiemethod对模成形法laminatingmethod被覆淋膜成形lowpressurecasting低压铸造lostwaxcasting脱蜡铸造matchedmouldthermalforming对模热成形模模具词汇英语翻译(成形不良用语) aberration色差bite咬入blackinghole涂料孔(铸疵)blackingscab涂料疤blister起泡blooming起霜blowhole破孔blushing泛白bodywrinkle侧壁皱纹breaking-in冒口带肉bubble膜泡burnmark糊斑burr毛边camber翘曲cell气泡centerbuckle表面中部波皱check细裂痕checking龟裂chipping修整表面缺陷clamp-off铸件凹痕collapse塌陷colormottle色斑corrosion腐蚀crack裂痕crazing碎裂crazing龟裂deformation变形edge切边碎片edgecrack裂边fading退色fillerspeak填充料斑fissure裂纹flangewrinkle凸缘起皱flaw刮伤flowmark流痕galling毛边glazing光滑gloss光泽greasepits污斑grindingdefect磨痕haircrack发裂haze雾度incrustation水锈indentation压痕internalporosity内部气孔mismatch偏模mottle斑点necking缩颈nick割痕rangepeel橘皮状表面缺陷overflow溢流peeling剥离pit坑pittingcorrosion点状腐蚀platemark模板印痕pock麻点pockmark痘斑resinstreak树脂流纹resinwear树脂脱落riding凹陷sagging松垂saponification皂化scar疤痕scrap废料scrapjam废料阻塞scratch刮伤/划痕scuffing深冲表面划伤seam裂痕shockline模口挤痕shortshot充填不足shrinkagepool凹孔sinkmark凹痕skininclusion表皮摺叠straightening矫直streak条状痕surfacecheck表面裂痕surfaceroughening橘皮状表皮皱摺surging波动torsion扭曲warpage翘曲waviness波痕webbing熔塌weldmark焊痕whitening白化wrinkle皱纹模具词汇英语翻译(塑胶原料)acrylic压克力casein酪素celluloseacetate醋酸纤维素CAcelluloseacetatebutyrate醋酸丁酸纤维素CABcompositematerial复合材料cresolresin甲酚树脂CFdiallyphthalate苯二甲酸二烯丙酯dispersereinforcement分散性强化复合材料engineeringplastics工程塑胶epoxyresin环氧树脂EPethylcellulose乙基纤维素ethylenevinylacetatecopolymer乙烯-醋酸乙烯EVAethylene-vinlacetatecopolyme醋酸乙烯共聚物EVAfiberreinforcement纤维强化热固性/纤维强化复合材料highdensitypolyethylene高密度聚乙烯HDPEhighimpactpolystyrene高冲击聚苯乙烯HIPShighimpactpolystyrenerigidity高冲击性聚苯乙烯lowdensitypolyethylene低密度聚乙烯LDPEmelamineresin三聚氰胺酚醛树脂MFnitrocellulose硝酸纤维素phenolicresin酚醛树脂plastic塑胶polyacrylicacid聚丙烯酸PAPpolyamide耐龙PApolybutyleneterephthalate聚对苯二甲酸丁酯PBTpolycarbonate聚碳酸酯PCpolyethyleneglycol聚乙二醇PFGpolyethyleneoxide聚氧化乙烯PEOpolyethyleneterephthalate聚乙醇对苯PETPpolymetylmethacrylate聚甲基丙烯酸甲酯PMMApolyoxymethylene聚缩醛POMpolyphenyleneoxide聚硫化亚苯polyphenyleneoxide聚苯醚PPOpolypropylene聚丙烯PPpolystyrene聚苯乙烯PSpolytetrafluoroethylene聚四氟乙烯PTFEpolytetrafluoroethylene聚四氟乙烯polythene聚乙烯PEpolyurethane聚氨基甲酸酯PUpolyvinylacetate聚醋酸乙烯PVACpolyvinylalcohol聚乙烯醇PVApolyvinylbutyral聚乙烯醇缩丁醛PVBpolyvinylchloride聚氯乙烯PVCpolyvinylfuoride聚氟乙烯PVFpolyvinylidenechloride聚偏二氯乙烯PVDCprepolymer预聚物siliconeresin矽树脂thermoplastic热塑性thermosetting热固性thermosettingplastic塑胶unsaturatedpolyester不饱和聚酯树脂模具词汇英语翻译(射出成形)activator活化剂bagmoulding气胎施压成形bondingstrength黏合强度breathing排气caulkingcompound填隙料cell气孔coldslug半凝式射出colorant著色剂colormatching调色colormasterbatch色母料compound混合料copolymer共聚合体cull残料废品cure凝固化cryptometer不透明度仪daylight开隙drycycletime空料试车周期时间ductility延性elastomer弹性体extrudedbeadsealing压出粒涂层法feed供料filler充填剂filmblowing薄膜吹制法floatingplaten活动模板foamingagent发泡剂gloss光泽granule颗粒料gunk料斗hotmark热斑hotstamping烫印injectionnozzle射出喷嘴injectionplunger射出柱塞injectionram射出冲柱isomer同分异构物kneader混合机levelingagent匀涂剂lubricant润滑剂matcheddiemethod配合成形法mouldclampingforce锁模力mouldreleaseagent脱模剂nozzle喷嘴orientedfilm取向薄膜parison吹气成形坏料pellet粒料plasticizer可塑剂plunger压料柱塞porosity孔隙率postcure后固化premix预混料purging清除reciprocatingscrew往复螺杆resilience回弹性resininjection树脂射出法rheology流变学sheet塑胶片shot注射shotcycle射出循环slipagent光滑剂takeoutdevice取料装置tiebar拉杆toggletypemouldclampingsystem肘杆式锁模装置torpedospreader鱼雷形分流板transparency透明性voidcontent空洞率模具词汇英语翻译(表面处理) agehardening时效硬化ageing老化处理airhardening气体硬化airpatenting空气韧化annealing退火anodeeffect阳极效应anodizing阳极氧化处理atomloytreatment阿托木洛伊表面austempering奥氏体等温淬火austenite奥斯田体/奥氏体bainite贝氏体bandedstructure条纹状组织barrelplating滚镀barreltumbling滚筒打光blackening染黑法blueshortness青熟脆性bonderizing磷酸盐皮膜处理boxannealing箱型退火boxcarburizing封箱渗碳brightelectroplating辉面电镀brightheattreatment光辉热处理bypassheattreatment旁路热处理carbide炭化物carburizedcasedepth浸碳硬化深层carburizing渗碳cementite炭化铁chemicalplating化学电镀chemicalvapordeposition化学蒸镀coarsening结晶粒粗大化coating涂布被覆coldshortness低温脆性comemtite渗碳体controlledatmosphere大气热处理cornereffect锐角效应creepingdischarge蠕缓放电decarburization脱碳处理decarburizing脱碳退火depthofhardening硬化深层diffusion扩散diffusionannealing扩散退火electrolytichardening电解淬火embossing压花etching表面蚀刻ferrite肥粒铁firststageannealing第一段退火flamehardening火焰硬化flametreatment火焰处理fullannealing完全退火gaseouscyaniding气体氧化法globularcementite球状炭化铁grainsize结晶粒度granolitetreatment磷酸溶液热处理graphitizing石墨退火hardenability硬化性hardenabilitycurve硬化性曲线hardening硬化heattreatment热处理hotbathquenching热浴淬火hotdipping热浸镀inductionhardening高周波硬化ioncarbonitriding离子渗碳氮化ioncarburizing离子渗碳处理ionplating离子电镀isothermalannealing等温退火liquidhoning液体喷砂法lowtemperatureannealing低温退火malleablizing可锻化退火martempering麻回火处理martensite马氏体/硬化铁炭metallikon金属喷镀法metallizing真空涂膜nitriding氮化处理nitrocarburizing软氮化normalizing正常化oilquenching油淬化overageing过老化overheating过热pearlite针尖组织phosphating磷酸盐皮膜处理physicalvapordeposition物理蒸镀plasmanitriding离子氮化pre-annealing预备退火precipitation析出precipitationhardening析出硬化pressquenching加压硬化processannealing制程退火quenchageing淬火老化quenchhardening淬火quenchingcrack淬火裂痕quenchingdistortion淬火变形quenchingstress淬火应力reconditioning再调质recrystallization再结晶redshortness红热脆性residualstress残留应力retainedaustenite残留奥rustprevention防蚀saltbathquenching盐浴淬火sandblast喷砂处理seasoning时效处理secondstageannealing第二段退火seculardistortion经年变形segregation偏析selectivehardening部分淬火shotblast喷丸处理shotpeening珠击法singlestagenitriding等温渗氮sintering烧结处理soaking均热处理softening软化退火solutiontreatment固溶化热处理spheroidizing球状化退火stabilizingtreatment安定化处理straighteningannealing矫直退火strainageing应变老化stressrelievingannealing应力消除退火subzerotreatment生冷处理supercooling过冷surfacehardening表面硬化处理temperbrittleness回火脆性tempercolour回火颜色tempering回火temperingcrack回火裂痕texture咬花thermalrefining调质处理thermoechanicaltreatment加工热处理timequenching时间淬火transformation变态tufftrideprocess软氮化处理underannealing不完全退火vacuumcarbonitriding真空渗碳氮化vacuumcarburizing真空渗碳处理vacuumhardening真空淬火vacuumheattreatment真空热处理vacuumnitriding真空氮化waterquenching水淬火wetout浸润处理模具词汇英语翻译(模具常用刀具工作法) adjustablespanner活动扳手anglecutter角铣刀arbour心轴backing衬垫beltsander带式打磨机buffing抛光chamferingmachine倒角机chamferingtool去角刀具chisel扁錾chuck夹具compass两角规concavecutter凹面铣刀convexcutter凸形铣刀crossjoint十字接头cuttingedgeclearance刃口余隙角drillstand钻台edgefile刃用锉刀file锉刀flangejoint凸缘接头grinder砂轮机hammer铁锤handbrace手摇钻hatching剖面线hexagonheadedbolt六角头螺栓hexagonnut六角螺帽indexhead分度头jack千斤顶jig治具kit工具箱lapping研磨metalsaw金工锯noseangle刀角pinchers钳子pliers铗钳plug柱塞头polisher磨光器protabledriller手提钻孔机punch冲头sandpaper砂纸scraper刮刀screwdriver螺丝起子scribing划线secondoutfile中纹锉spanner扳手splinebroach方栓槽拉刀square直角尺squaresleeker方形镘刀squaretrowel直角度stripping剥离工具T-slotT形槽toolforlathe车刀toolpointangle刀刃角toolpost刀架tosecan划线盘trimming去毛边waffledieflattening压纹效平wiper脱模钳wrench螺旋扳手模具词汇英语翻译(冲模加工) barreling滚光加工belling压凸加工bending弯曲加工blanking下料加工bulging撑压加工burring冲缘加工camdiebending凸轮弯曲加工coining压印加工compressing压缩加工compressionbending押弯曲加工crowning凸面加工curlbending卷边弯曲加工curling卷曲加工cutting切削加工dinking切断蕊骨doubleshearing叠板裁断drawing引伸加工drawingwithironing抽引光滑加工embossing浮花压制加工extrusion挤制加工filing锉削加工fineblanking精密下料加工finishblanking光制下料加工finishing精整加工flanging凸缘加工folding折边弯曲加工folding摺叠加工forming成形加工impactextrusion冲击挤压加工indenting压痕加工ironing引缩加工knurling滚花lockseaming固定接合louvering百叶窗板加工marking刻印加工necking颈缩加工notching冲口加工parting分断加工piercing冲孔加工progressivebending连续弯曲加工progressiveblanking连续下料加工progressivedrawing连续引伸加工progressiveforming连续成形加工reaming铰孔加工restriking二次精冲加工riveting铆接加工rollbending滚筒弯曲加工rollfinishing滚压加工rolling压延加工roughing粗加工scraplessmachining无废料加工seaming折弯重叠加工shaving缺口修整加工shearing切断加工sizing精压加工/矫正加工slitting割缝加工spinning卷边?接stamping锻压加工swaging挤锻压加工trimming整缘加工upsetting锻粗加工wiring抽线加工模具词汇英语翻译(冲压机械及周边) backshaft支撑轴blankdetermination胚料展开bottomslidepress下传动式压力机boarddrophammer板落锤brake煞车buckle剥砂面camlachiecramp铸包chamottesand烧磨砂charginghopper加料漏斗clearance间隙closed-dieforging合模锻造clump夹紧clutch离合器clutchbrake离合器制动器clutchboss离合器轮壳clutchlining离合器覆盖coilcar带卷升降运输机coilcradle卷材进料装置coilreelstand钢材卷料架column圆柱connectionscrew连杆调节螺钉corecompound砂心黏结剂counterblowhammer对击锻锤cradle送料架crank曲柄轴crankless无曲柄式crosscrank横向曲轴cushion缓冲depression外缩凹孔dialfeed分度送料dieapproach模口角度dieassembly合模diecushion模具缓冲垫dieheight冲压闭合高度dielife模具寿命dieopening母模逃孔diespottingpress调整冲模用压力机doublecrankpress双曲柄轴冲床draghtangle逃料倾斜角edging边锻伸embeddedcore加装砂心feedlength送料长度feedlevel送料高度fillingcore埋入砂心fillingin填砂filmplay液面花纹fineblankingpress精密下料冲床forgingroll辊锻机finishingslag炼后熔渣flywheel飞轮flywheelbrake飞轮制动器footpress脚踏冲床formboard进模口板frame床身机架friction摩擦frictionbrake摩擦煞车gapshear凹口剪床gear齿轮gib滑块引导部gripper夹具gripperfeed夹持进料gripperfeeder夹紧传送装置hammer槌机handpress手动冲床handrackpinionpress手动齿轮齿条式冲床handscrewpress手动螺旋式冲床hopperfeed料斗送料idlestage空站inching微调尺寸isothermalforging恒温锻造keyclutch键槽离合器knockout脱模装置knucklemechanic转向机构land模具直线刀面部loader供料器unloader卸料机loopcontroller闭回路控制器lowerdie下模microinchingdevice微寸动装置microinchingequipment微动装置movingbolster活动工作台notchingpress冲缺口压力机opening排料逃孔overloadprotectiondevice防超载装置pinchroll导正滚轮pinion小齿轮pitch节距pressfit压入progressive连续送料pusherfeed推杆式送料pusherfeeder料片押片装置quickdiechangesystem快速换模系统regrinding再次研磨releasing松释动作reversedblanking反转下料robot机器人rollformingmachine辊轧成形rollformingmachine辊轧成形机rollrelease脱辊rollerfeed辊式送料rollerleveler辊式矫直机rotarybender卷弯成形机safetyguard安全保护装置scrapcutter废料切刀scrappress废料冲床seamlessforging无缝锻造shave崩砂shearangle剪角sheetloader薄板装料机shot单行程工作shrinkagefit收缩配合shutheight闭合高度sievemesh筛孔sinteringofsand铸砂烧贴slidebalancer滑动平衡器slughole逃料孔spinformingmachine旋压成形机spotting合模stackfeeder堆叠拨送料机stickness黏模性straightsideframe冲床侧板stretcherleveler拉伸矫直机stripfeeder料材送料装置strippingpressure弹出压力stroke冲程takeoutdevice取料装置togglepress肘杆式压力机transferfeed连续自动送料装置turrentpunchpress转塔冲床twospeedclutch双速离合器uncoiler闭卷送料机unloader卸载机vibrationfeeder振动送料机wiringpress嵌线卷边机模具词汇英语翻译(线切割放电加工关连用语) abnormalglow不规则辉光放电arcdischarge电弧放电belt皮带centreless无心chromebronze铭铜clearanceangle后角cornersheardrop直角压陷deflection桡曲度dischargeenergy放电能量dressing修整dwell保压flange凸缘gap间隙graphite石墨graphitecontractionallowance电极缩小余量graphiteholder电极夹座haircrack发裂horn电极臂jump跳刀magneticbase磁性座mastergraphite标准电极pipegraphite管状电极pulse脉冲ribworking肋部加工rollerelectrode滚轮式电极rotarysurface旋转面shank柄部sharpedge锐角部toughbronze韧铜traverse摇臂tungstenbronze钨青铜waviness波形起伏workingallowance加工余量workingdischard加工废料模具相关词汇英语翻译(锻铸造关连用语) accretion炉瘤acidconverter酸性转炉acidliningcupola酸性熔铁炉acidopen-hearthfurnace酸性平炉aerator松砂机airsetmold常温自硬铸模airlessblastingcleaning离心喷光allcoremolding集合式铸模allrounddieholder通用模座assemblymark铸造合模记号backpouring补浇注backingsand背砂basebullion粗金属锭basepermeability原砂透气度belling压凸billet坏料bleed漏铸blocker预锻模膛blocking粗胚锻件blowhole铸件气孔boarddrophammer板落锤bottompourmold底浇bottompouring底注boxlessmold脱箱砂模break-offcore缩颈砂心brickmolding砌箱造模法buckle剥砂面camber错箱camlachiecramp铸包castblade铸造叶片castingflange铸造凸缘castingonflat水平铸造chamottesand烧磨砂charginghopper加料漏斗cleaningofcasting铸件清理closed-dieforging合模锻造corecompound砂心黏结剂coretemplate砂心模板corevent砂蕊排气孔cornergate压边浇口counterblowhammer对击锻造counterlock止口镶嵌方式depression外缩凹孔dieapproach模口角度drawout锻造拔长drawplate起模板drawspike起模长针dummying预锻embeddedcore加装砂心erosion冲砂fettling铸件清理fillingcore埋入砂心fillingin填砂filmplay液面花纹finishingslag炼后熔渣flashgutter锻模飞边槽flaskmolding砂箱造模forgingroll辊锻机formboard进模口板gutter锻模飞边槽hammerman锻工headingmachine顶镦机impacter卧式锻造机inblockcast整体铸造ingot铸锭ingotblank铸坯inlaycasting镶铸法investmentcasting失模铸造isothermalforging恒温锻造loosepiece木模活块moldingpit铸模地坑pouringprocess浇注法recasting重铸rollforging轧锻rolledsurface轧制表面roughsand粗砂roughingforge粗锻sandcrushing塌箱seamlessforging无缝锻造separate分离shave崩砂shrinkagefit收缩配合shutheight闭合高度sievemesh筛孔sinteringofsand铸砂烧贴slag熔渣slaginclusion夹渣stickness黏模性striplayout带状胚料排样法tapcasting顶注topgate顶注浇口unworkedcasting不加工铸件upender翻转装置upending顶锻uphillcasting底铸whitecastiron白口铸件模具词汇相关英语翻译(砂轮用语) abrasive砂轮Al2O3氧化铝borazon氧化硼立方晶buffingwheel抛光布轮diamond钻石dresser砂轮整修机dressing修整endlessgrindingbelt循环式研磨带finishingallowance加工余量grain磨粒grindingdisc研磨盘jampup孔眼堵塞mesh网筛目resinoidgrindingwheel半树脂型砂轮slitting切缝量vitrified陶瓷的模具加工方法词汇的英语翻译barrel滚筒(加工)bending波纹加工broaching拉刀切削centering定中心cutting切削cylindricallathecutting外圆车削electricdischargemachine放电加工electrolyticgrinding电解研磨embossing压花加工facing面车削filing锉刀修润handfinishing手工修润hemming卷边加工hobbing滚齿加工joggling摇动加工lapping抛光/研磨修润laserbeammachining雷射加工lathecutting车床车削planning刨削加工polishing抛亮光reaming铰孔修润roughmachining粗切削rounding圆形加工sawing锯削scaling清除钢碇缺陷shaping成形加工skiving表面研磨slotting切缝切削taperturning锥度车削threadcutting螺纹切削ultrasonicmachining超音波加工upcutmilling逆铣加工特别声明：1：资料来源于互联网，版权归属原作者2：资料内容属于网络意见，与本账号立场无关3：如有侵权，请告知，立即删除。
模具专业的英语词汇大全
模具专业的英语词汇大全一、模具基础词汇1. Mold 模具2. Die 冲模3. Core 核心模4. Cavity 型腔5. Mold Base 模架6. Mold Steel 模具钢7. Runner 流道8. Gate 进浇口9. Ejector Pin 顶针10. Ejector Plate 顶板二、模具设计相关词汇1. Draft Angle 脱模斜度2. Parting Line 分模线3. Radius 圆角4. Undercut 难以脱模的凹槽5. Slide 滑块6. Lifters 顶杆7. Cooling Channel 冷却水道8. Injection Point 注射点9. Shrinkage 收缩率10. Molding Cycle 成型周期三、模具加工与维护词汇1. Machining 加工2. Milling 铣削3. Grinding 磨削4. EDM (Electrical Discharge Machining) 电火花加工5. Wire Cutting 线切割6. Polishing 抛光7. Assembly 装配8. Maintenance 维护9. Repair 修理10. Replacement 更换四、模具材料与热处理词汇1. Tool Steel 工具钢2. Stainless Steel 不锈钢3. Aluminum 铝4. Plastic 塑料5. Rubber 橡胶6. Heat Treatment 热处理7. Hardness 硬度8. Tempering 回火9. Quenching 淬火10. Annealing 退火五、模具行业相关词汇1. Mold Maker 模具师傅2. Mold Designer 模具设计师3. Mold Manufacturer 模具制造商4. Injection Molding 注塑成型5. Blow Molding 吹塑成型6. Compression Molding 压缩成型7. Transfer Molding 传递成型8. Prototype Model 原型模具9. Mass Production 批量生产10. Quality Inspection 质量检验六、模具测试与质量控制词汇1. First Article Inspection 首件检查2. Sample 样品3. Defect 缺陷4. Dimensional Accuracy 尺寸精度5. Tolerance 公差6. Surface Finish 表面光洁度7. Stress Analysis 应力分析8. Flow Analysis 流动分析9. Mold Flow Simulation 模具流动模拟10. Quality Control 质量控制七、模具行业常用设备词汇1. Injection Molding Machine 注塑机2. Extruder 挤出机3. Blow Molding Machine 吹塑机4. CNC Machine 数控机床5. Lathe 车床6. Milling Machine 铣床7. Grinder 磨床8. EDM Machine 电火花机床9. Laser Cutter 激光切割机10. Robot 自动化八、模具生产流程词汇1. Design Drawing 设计图纸2. Mold Construction 模具构建3. Machining Process 加工工艺4. Tooling Setup 模具安装5. Trial Run 试模6. Adjustment 调整7. Production Run 生产运行8. Mold Maintenance 模具保养9. Mold Modification 模具修改10. Mold Recycling 模具回收九、模具行业认证与标准词汇1. ISO Certification ISO认证2. Quality Management System 质量管理体系3. Standard 标准化4. DIN 德国工业标准5. ASTM 美国材料与试验协会6. JIS 日本工业标准7. Certification Body 认证机构8. Audit 审核检查9. Compliance 符合性10. Continuous Improvement 持续改进十、模具行业发展趋势词汇1. Automation 自动化2. Intelligent Manufacturing 智能制造3. 3D Printing 三维打印4. Rapid Prototyping 快速原型5. Industry 4.0 工业4.06. Internet of Things (IoT) 物联网7. Big Data 大数据8. Cloud Computing 云计算9. Sustainable Development 可持续发展10. CrossIndustry Integration 跨行业整合通过这些词汇，我们可以看到模具行业不仅涉及具体的技术和操作，还包括了管理、质量控制、认证以及未来的发展趋势。
模具英语专业术语分析解析
模具（MOULD/MOLD，TOOL）：CAVITY：前模CORE：后模（定模）DIMENSION：寸法GATE：浇口/水口/入水口PIN GATE：点水口/点浇入水SIDE GATE：边水口/侧浇入水/大水口APPERANCE SURFACE：体裁面WARPAGE DIRECTION：变形方向DRAFT ANGEL：脱模斜度PARTING LINE/P。
L：分模线EJECT PIN/E。
P：注塑顶针BLAST/TEXTURE：喷啥，蚀纹MIRROR FINISH：镜面（抛光）处理POLISH：抛光EMD：放电加工WELD：熔接加工（烧焊）LATHE：车床MILLING CUTTER：铣刀MILLING MACHINE：铣床WIRE CUT：线切割CNC：主加工中心POWER DRILL：电钻DRILLING：钻孔FRITING：烧结ANNEALING：淬火注塑术语（INJECTION）SCREW：螺杆WELD LINE：熔接线SINK MARK：缩水DRAG MARK：脱花BURR：批锋FLOW MARK：流纹SHADOW MARK/GLOSS DIFFERENCE：光影SHORT：缺胶INJECTION CYCLE：成型周期注塑英语型厚大小Thick size锁模结构（机绞/直压）Mode locking structure(machine twists/straight pressure)最大开模距离The biggest die sinking is away from动模板最大模具重量Moves the template maximum mold weight哥林柱间距Elder brother forest column spacing顶出形式（电动五点，油压五点，油压十三点）Goes against the form (electrically operated five spots, flowing tubing head pressure five spots, flowing tubing head pressure 13 spots)顶出长度Goes against the length顶棍孔直径Goes against the stick hole diameter顶棍孔中心矩Goes against the stick hole central moment螺杆材质（合金）Screw rod material quality (alloy)螺杆转速Screw rod rotational speed最大射出体积Projects the volume most greatly最大射出量Projects the quantity most greatly射出率Ejection rate每10mm射出量（理论）Each 10mm projects the quantity (theory)射咀直径Shoots ju the diameter射咀R值Shoots ju the R value射咀空径Shoots ju the spatial diameter定位环直径Locating ring diameter溶胶能力Sol ability驱动方式（全自动/全液压）Drive type (completely automatic/entire hydraulic pressure)电压Voltage电热功率Electric heating power电机功率Electrical machinery power作动油量Does moves the oil mass机械尺寸Mechanical size机械重量Mechanical weight最高溶胶温度Highest sol temperature是否带中子Whether to bring the neutron是否带吹气Whether to have the air flus开模行程，open ould stroke定产，order production定产效率，efficiency of order prod uction注胶切换点，glue-injection switching point保压压力1，protective pressure倒索，inverse sling模保护，mould protection关模低压，close mould low pressure炮筒温度，gun barrel temperature回料量，returning amount注射压力，injecting pressure色母配比，raw color ratio mixing配套摸具，matched mold顶针次数，thimble times立式注胶机vertical injector工艺卡，WSP(work specification procedure)工作指导work instr uction注塑机部分英语钣金machine cover / upper cover/ side cover锁模部分clamping unit射胶部分injection unit机架machine frame / base电气系统electric system液压系统hydraulic system机械系统mechanical system机门safety door / fixed door / movable door锁模部分clamping unit电脑控制器computer controller机械安全锁mechanical safety interlock射胶部分injection unit液压系统hydraulic system电箱electrical cabinet / cable机架分体线stand split line机架螺丝孔foundation bolt hole机架machine base / supporting frame理论注射容积theoretical shot volume实际注射量shot weight螺杆直径screw diameter注射压力injection pressure注射速度injection speed注射速率injection rate螺杆长径比screw L/D ratio螺杆行程screw stroke螺杆转速screw speed熔胶能力plasticizing capacity锁模力clamping force开模/锁模行程mold clamping / opening stroke模板尺寸platen size拉杆间距distance between tie bars / rods模板最大距离max. daylight容模量mold thickness (min. & max.)顶出行程hydraulic ejection stroke顶出力hydraulic ejection force顶针数nos. of ejector pin液压系统压力hydraulic system pressure油泵马达pump motor电热量heating capacity温度控制区数nos. of temp control zones射嘴接触力nozzle contact forceInjection 注射Mould closing 关模Cooling time冷却时间Holding time 保压时间Injection start delay 注射延迟Injection alarm time注射报警时间Final cushion minimum value最后段位置Change-over to holding by value切换到锁模Plasticizing end value预塑重终点Hydrarlic change-over pressure holding切换到保压Screwvalue for change-over to holding加料Hydraulic pressure in holding锁模力Filling stage pressure limit充模压力Injection speed注射速度Plasticizing delay预塑延时1st suck-back speed储料一速度1st suck-back pressure储料一压力Screwrotation speed螺杆转速Decompression value at end of injection注射终点Decompression value at end of plasticizing预塑终点Mould close force关模压力Mould closing safety time .. 时间Mould closing pressure .. 压力1st closing safety stage pressure 合模一段压力1st mould closing speed ...成型速度1st stage mould closing safety position.....位置High pressure start position高压锁模位置注塑专业英语Surface Appearance外观Glossiness/gloss finish光洁度Matt finish/matt surface毛面Glass fiber rich surface/glass emergence on the surface 玻纤外露Blooming/surface blooming表面析出White patches on surface表面白斑Silver marks/silver streak银纹Splay mark水纹Flow mark流纹Weld line溶结纹Brittle/brittleness脆Bubbles/trapped gas气泡Void孔Burn marks烧伤FR failed阻燃不合格Flame rating V-2阻燃V-2Poor dispersion分散不好FR/PTFE …agglomerates etc 阻燃剂/PTFE…结块Pellet porous粒子不密/蜜蜂窝Low impact/tensile etc物理性能低High flow/filler content etc流动性/填充…过高Longs/fines/doubles长粒/碎屑/连粒Poor cut粒形不好Bristle/voids表面有小气泡/孔Glass bundles玻纤结团Product was rejected due to 产品不能接受因为…High moisture level高水分Warpage/warped翘曲Shrinkage/shrink收缩Sink marks缩影Short shot/short molding打不满Distortion变形Over dimension尺寸过大Under dimension尺寸过小Flashing飞边Discoloration变色Off color颜色差异Flow rate流动率Viscous粘High flow高流动Low flow低流动Sticky粘Mold release脱模Antioxidant抗氧剂Flame retardant agent阻燃剂Heat stabilizer热稳定剂Chopped glass fiber短切玻纤Roving glass fiber粗纱/长玻纤Glass beads玻璃微珠Milled fiber碾磨纤Molybdenum disulfide/moly/MoS2 二硫化钼Colorant着色剂Pigment颜料Dye染料Accepted product specification接受产品规格Approved our product认可我们的产品Re-set spec重新定标准Add in e xtra …添加多一点…Reduced … content减少…含量Dropped/reduced … by x％减少…含量…％Confirmed color standard确认颜色标准Approved color standard认可颜色标准Re-confirmed color standard重新确认颜色标准Qualified our product认可我们的产品Undergoing heat aging test在做热老化实验Product is under testing产品在测试当中Received first order接了第一个定单Expected to finish by …预计在…完成Expected order is xMT预计定单量…吨Estimated annual/monthly consumption预计年/月用量--- 详细信息1. 注射模具名称注射模：Injection mould热塑性塑料注射模：Injection mould for thermoplasctics 热固性塑料注射模：Injection mould for thermosets无流道模：Runerless mould热流道模：Hot runner mould绝热流道模：Insulated温流道模：Warm runner mould2. 浇注，排溢，分型浇注系统：Feed system主流道：Sprue分流道：Runner浇口：Gate直接浇口：Direct gate ;Sprue gate环行浇口：Ring gate盘型浇口：Disk gate ;Diaphragm轮辐浇口：Spoke gate :Spider gate点浇口：Pin-point gate侧浇口：Edge gate潜伏浇口：Submarine gate护耳浇口：Tab gate扇型浇口：Fan gate 牛角浇口：Horn gate冷料穴：Cold-slug well浇口套：Sprue bush ;Sprue bushing浇口镶块：Gating insret分流锥：Sprader流道板：Runner plate热流道板：Manifold block;Hot-runner manifold温流道板：Warm runner plate二级喷嘴：Secondary nozzle鱼雷形组合体：Torpedo;Torpedo body assembly管式加热器：Cartridge heater热管：Heat pipe阀式浇口：Valve gate加热腔：Loading chamber柱塞：Force plunger;Pot plungr溢料槽：Flash grorve ;Spew grovve排气槽：Vent分型面：Parting line水平分型面：Horizontal parting half垂直分型面：Vertical parting half3. 成型零件定模：Stationary mould:Fixed half动模；Movable mould ;Moving half上模:Upper mould;Upper half下模：Lower mould :Lower half型腔：Cavity凹模：Impression;Cavity plate镶件：Mould insert活动镶件：Movable insert;Lose detail拼块：Splits凹模拼块：Cavity splits型芯拼块：Core splits型芯：Core侧型芯：Side core:slide core螺纹型芯：Thread plug;Threaded core螺纹型环：Thread ring;Threaded cavity凸模：Punch;Force嵌件：Insert for mould4. 支持与固定零件定模座板：Fixed clamp plate:Top clamping plate;Top plate动模座板：Moving clamp plate :Bottom clamping plate; Bottm plate 上模座板：Upper clamping plate下模座板：Lower clamping plate凹模固定板：Cavity-retaier plate型芯固定板：Core-retaier plate凸模固定板：Punch-retaier pilte模套：Chase ;Bolster;Frame;支撑板：Backing plate垫块：Spacer parallel支架：Ejector housing支撑柱：Support pillar模板：Mould plate5. 抽芯零件斜销：Angle pin; Finger cam滑块：Slide;Cam slide侧型芯滑块：Slide core-slide滑块导板：Slide guide strip锲紧块：Heel block;Wedge block;Locking heel斜槽导板：Finger guide plate弯销：Dog-leg cam斜滑块：Angled-lift splits6. 导向零件导柱：Guide pillar;Guide pin;Leader pin带头导柱：Guide pillar ;Straight leader pin带肩导柱：Guide pillar Shouldered;Shoulder leader pin推板导柱：Ejector guide pillar;Ejeector guide pin导套：Guide bush ;Guide bushing直导套：Guide bush ;Straight ;Straight bushing带头导套：Guide bush ;Shoulder bushing推板导套：Ejector guide bush;Ejector bushing7. 定位和限位零件定位圈：Locating ring锥形定位圈：Mould bases locating elements复位杆：Ejector plate return pin;Push-back pin限位钉：Stop pin;Stop button限位块：Stop block ;Stop pad定距拉杆：Length bolt;Puller bolt定距拉板：Puller plate;Limit plate8. 推出零件推杆：Ejector pin圆柱头推杆：Ejector pin with cytindrical head带肩推杆:Shouldered ejector pin扁推杆:Flar ejector pin推管：Ejector sleeve推块：Ejector pad推件板：Stripper plate推件环：Stripper ring;Stripper dlisk推杆固定板：Ejector retainer plate推板：Ejector plate;Ejection plate连接推杆：Ejector tie rod 拉料杆：Sprue puller钩形垃料杆：Sprue puller ;Z-shaped球头垃料杆：Sprue puller;Ball headed圆锥头垃料杆：Sprue puller;Conical headed分流道垃料杆：Runner puller;Runner lock pin推流道板：Runner stripper plate9. 冷却和加热零件冷却通道：Cooling channel;Cooling line隔板：Baffle加热板：Heating plate隔热板：Thermal insulation board10. 模架模架：Mould base标准模架：Standard mould base11. 塑料成型模具的主要设计要素注射能力：Shot capacity收缩率：Shrinkage注射压力：Injection pressure锁模力：Clamping force ;Locking force成型压力：Moulding pressure模内压力：Internal mould pressure;Cavity pressure 开模力：Mould opening force脱模力：Ejection force抽芯力：Core-pulling force抽芯距：Core-pulling distance闭合高度：Mould shut height最大开距：Maximum daylight;Open daylight投影面积：Projected area脱模斜度：Draft脱模距：Stripper distance。
模具专业英语词汇
Here is a list of mold-related vocabulary in English:1. Mold -模具2. Mold cavity -模腔3. Mold core -模芯4. Mold base -模座5. Injection molding -注塑成型6. Blow molding -吹塑成型7. Compression molding -压缩成型8. Extrusion molding -挤出成型9. Rotational molding -旋转成型10. Thermoforming -热成型11. Mold design -模具设计12. Mold manufacturing -模具制造13. Mold making -模具加工14. Mold material -模具材料15. Mold steel -模具钢16. Mold release agent -脱模剂17. Mold temperature -模具温度18. Mold flow analysis -模流分析19. Mold maintenance -模具维护20. Mold repair -模具修复22. Mold polishing -模具抛光23. Molded part -注塑件24. Molded product -成型产品25. Molded surface -成型表面26. Molded feature -成型特征27. Ejector pins -顶出针28. Runner system -流道系统29. Cooling system -冷却系统30. Venting -通气31. Molded part defects -成型件缺陷32. Molded part warpage -成型件翘曲33. Molded part shrinkage -成型件收缩34. Mold release system -脱模系统35. Mold venting system -通气系统36. Mold temperature controller -模具温度控制器37. Mold gate -模具流道口38. Mold runner -模具流道39. Mold ejector system -模具顶出系统40. Mold clamping force -模具锁模力41. Mold shot size -模具射胶量42. Mold cycle time -模具循环时间44. Mold cooling time -模具冷却时间45. Mold release mechanism -模具脱模机构46. Molded part dimensions -成型件尺寸47. Molded part tolerance -成型件公差48. Molded part surface finish -成型件表面处理49. Molded part strength -成型件强度50. Molded part flexibility -成型件柔韧性51. Molded part accuracy -成型件精度52. Molded part durability -成型件耐久性53. Molded part weight -成型件重量54. Molded part texture -成型件纹理55. Molded part transparency -成型件透明度56. Molded part color -成型件颜色57. Molded part function -成型件功能58. Molded part assembly -成型件装配59. Molded part packaging -成型件包装60. Molded part labeling -成型件标记61. Molded part quality control -成型件质量控制62. Mold material selection -模具材料选择63. Mold design software -模具设计软件64. Mold manufacturing process -模具制造过程65. Mold injection molding machine -模具注塑机66. Mold blow molding machine -模具吹塑机67. Mold compression molding machine -模具压缩成型机68. Mold extrusion molding machine -模具挤出成型机69. Mold rotational molding machine -模具旋转成型机70. Mold thermoforming machine -模具热成型机71. Mold tooling -模具工装72. Molded part inspection -成型件检验73. Molded part packaging -成型件包装74. Molded part labeling -成型件标记75. Molded part storage -成型件存储76. Molded part transportation -成型件运输77. Molded part disposal -成型件处理78. Molded part recycling -成型件回收79. Molded part cost -成型件成本80. Molded part production rate -成型件生产率81. Molded part tooling cost -成型件工装成本82. Molded part tooling lead time -成型件工装交货期83. Molded part tooling lifespan -成型件工装寿命84. Molded part tooling maintenance -成型件工装维护85. Molded part tooling repair -成型件工装修复86. Molded part tooling modification -成型件工装修改87. Molded part tooling replacement -成型件工装更换88. Molded part tooling storage -成型件工装存储89. Molded part tooling transportation -成型件工装运输90. Molded part tooling disposal -成型件工装处理91. Molded part tooling recycling -成型件工装回收92. Molded part tooling cost estimation -成型件工装成本估算93. Molded part tooling design optimization -成型件工装设计优化94. Molded part tooling production planning -成型件工装生产计划95. Molded part tooling quality control -成型件工装质量控制96. Molded part tooling process improvement -成型件工装工艺改进97. Molded part tooling waste reduction -成型件工装废物减少98. Molded part tooling cost reduction -成型件工装成本降低99. Molded part tooling cycle time optimization -成型件工装循环时间优化100. Molded part tooling material selection -成型件工装材料选择101. Molded part tooling design validation -成型件工装设计验证102. Molded part tooling production monitoring -成型件工装生产监控103. Molded part tooling maintenance scheduling -成型件工装维护计划104. Molded part tooling repair process -成型件工装修复流程105. Molded part tooling modification process -成型件工装修改流程106. Molded part tooling replacement process -成型件工装更换流程107. Molded part tooling storage management -成型件工装存储管理108. Molded part tooling transportation logistics -成型件工装运输物流109. Molded part tooling disposal methods -成型件工装处理方法110. Molded part tooling recycling techniques -成型件工装回收技术111. Molded part tooling cost estimation tools -成型件工装成本估算工具112. Molded part tooling design optimization software -成型件工装设计优化软件113. Molded part tooling production planning systems -成型件工装生产计划系统114. Molded part tooling quality control methods -成型件工装质量控制方法115. Molded part tooling process improvement strategies -成型件工装工艺改进策略116. Molded part tooling waste reduction techniques -成型件工装废物减少技术117. Molded part tooling cost analysis -成型件工装成本分析118. Molded part tooling design review -成型件工装设计审查119. Molded part tooling production efficiency -成型件工装生产效率120. Molded part tooling maintenance checklist -成型件工装维护清单121. Molded part tooling repair cost estimation -成型件工装修复成本估算122. Molded part tooling modification cost estimation -成型件工装修改成本估算123. Molded part tooling replacement cost estimation -成型件工装更换成本估算124. Molded part tooling storage system -成型件工装存储系统125. Molded part tooling transportation cost calculation -成型件工装运输成本计算126. Molded part tooling disposal methods evaluation -成型件工装处理方法评估127. Molded part tooling recycling process optimization -成型件工装回收流程优化128. Molded part tooling cost reduction strategies -成型件工装成本降低策略129. Molded part tooling cycle time reduction techniques -成型件工装循环时间减少技术130. Molded part tooling material waste reduction -成型件工装材料废物减少131. Molded part tooling design validation methods -成型件工装设计验证方法132. Molded part tooling production monitoring tools -成型件工装生产监控工具133. Molded part tooling maintenance scheduling software -成型件工装维护计划软件134. Molded part tooling repair process optimization -成型件工装修复流程优化135. Molded part tooling modification process improvement -成型件工装修改流程改进136. Molded part tooling replacement process optimization -成型件工装更换流程优化137. Molded part tooling storage management techniques -成型件工装存储管理技术138. Molded part tooling transportation logistics optimization -成型件工装运输物流优化139. Molded part tooling disposal methods assessment -成型件工装处理方法评估140. Molded part tooling recycling techniques evaluation -成型件工装回收技术评估141. Molded part tooling cost estimation software -成型件工装成本估算软件142. Molded part tooling design optimization tools -成型件工装设计优化工具143. Molded part tooling production planning systems evaluation -成型件工装生产计划系统评估144. Molded part tooling quality control methods assessment -成型件工装质量控制方法评估145. Molded part tooling process improvement strategies implementation -成型件工装工艺改进策略实施146. Molded part tooling waste reduction techniques optimization -成型件工装废物减少技术优化147. Molded part tooling cost analysis tools -成型件工装成本分析工具148. Molded part tooling design review software -成型件工装设计审查软件149. Molded part tooling production efficiency evaluation -成型件工装生产效率评估150. Molded part tooling maintenance checklist optimization -成型件工装维护清单优化151. Molded part tooling repair cost estimation software -成型件工装修复成本估算软件152. Molded part tooling modification cost estimation software -成型件工装修改成本估算软件153. Molded part tooling replacement cost estimation software -成型件工装更换成本估算软件154. Molded part tooling storage system optimization -成型件工装存储系统优化155. Molded part tooling transportation cost calculation software -成型件工装运输成本计算软件156. Molded part tooling disposal methods evaluation tools -成型件工装处理方法评估工具157. Molded part tooling recycling process optimization techniques -成型件工装回收流程优化技术158. Molded part tooling cost reduction strategies implementation -成型件工装成本降低策略实施159. Molded partooling design validation methods -成型件工装设计验证方法160. Molded part tooling production monitoring tools -成型件工装生产监控工具161. Molded part tooling maintenance scheduling software -成型件工装维护计划软件162. Molded part tooling repair process optimization -成型件工装修复流程优化163. Molded part tooling modification process improvement -成型件工装修改流程改进164. Molded part tooling replacement process optimization -成型件工装更换流程优化165. Molded part tooling storage management techniques -成型件工装存储管理技术166. Molded part tooling transportation logistics optimization -成型件工装运输物流优化167. Molded part tooling disposal methods assessment -成型件工装处理方法评估168. Molded part tooling recycling techniques evaluation -成型件工装回收技术评估169. Molded part tooling cost estimation software -成型件工装成本估算软件170. Molded part tooling design optimization tools -成型件工装设计优化工具171. Molded part tooling production planning systems evaluation -成型件工装生产计划系统评估172. Molded part tooling quality control methods assessment -成型件工装质量控制方法评估173. Molded part tooling process improvement strategies implementation -成型件工装工艺改进策略实施174. Molded part tooling waste reduction techniques optimization -成型件工装废物减少技术优化175. Molded part tooling cost analysis tools -成型件工装成本分析工具176. Molded part tooling design review software -成型件工装设计审查软件177. Molded part tooling production efficiency evaluation -成型件工装生产效率评估178. Molded part tooling maintenance checklist optimization -成型件工装维护清单优化179. Molded part tooling repair cost estimation software -成型件工装修复成本估算软件180. Molded part tooling modification cost estimation software -成型件工装修改成本估算软件181. Molded part tooling replacement cost estimation software -成型件工装更换成本估算软件182. Molded part tooling storage system optimization -成型件工装存储系统优化183. Molded part tooling transportation cost calculation software -成型件工装运输成本计算软件184. Molded part tooling disposal methods evaluation tools -成型件工装处理方法评估工具185. Molded part tooling recycling process optimization techniques -成型件工装回收流程优化技术186. Molded part tooling cost reduction strategies implementation -成型件工装成本降低策略实施187. Molded part tooling risk assessment methods -成型件工装风险评估方法188. Molded part tooling safety protocols optimization -成型件工装安全协议优化189. Molded part tooling environmental impact assessment -成型件工装环境影响评估190. Molded part tooling sustainability evaluation -成型件工装可持续性评估191. Molded part tooling efficiency improvement strategies implementation -成型件工装效率提升策略实施192. Molded part tooling inventory management techniques -成型件工装库存管理技术193. Molded part tooling repair process optimization -成型件工装修复流程优化194. Molded part tooling modification cost reduction techniques -成型件工装修改成本降低技术195. Molded part tooling replacement cost reduction strategies -成型件工装更换成本降低策略196. Molded part tooling storage space optimization techniques -成型件工装存储空间优化技术197. Molded part tooling transportation cost reduction strategies -成型件工装运输成本降低策略198. Molded part tooling disposal methods optimization -成型件工装处理方法优化199. Molded part tooling recycling process evaluation -成型件工装回收流程评估200. Molded part tooling cost analysis techniques -成型件工装成本分析技术201. Molded part tooling design review process optimization -成型件工装设计审查流程优化202. Molded part tooling production efficiency improvement strategies -成型件工装生产效率提升策略203. Molded part tooling maintenance checklist evaluation -成型件工装维护清单评估204. Molded part tooling repair process efficiency improvement techniques -成型件工装修复流程效率提升技术205. Molded part tooling modification cost reduction strategies -成型件工装修改成本降低策略206. Molded part tooling replacement cost reduction techniques -成型件工装更换成本降低技术207. Molded part tooling storage system evaluation -成型件工装存储系统评估208. Molded part tooling transportation cost analysis techniques -成型件工装运输成本分析技术209. Molded part tooling disposal methods optimization strategies -成型件工装处理方法优化策略210. Molded part tooling recycling process efficiency improvement techniques -成型件工装回收流程效率提升技术211. Molded part tooling cost reduction strategies implementation -成型件工装成本降低策略实施212. Molded part tooling risk assessment techniques -成型件工装风险评估技术213. Molded part tooling safety protocols evaluation -成型件工装安全协议评估214. Molded part tooling environmental impact assessment techniques -成型件工装环境影响评估技术215. Molded part tooling sustainability improvement strategies -成型件工装可持续性改进策略216. Molded part tooling efficiency evaluation techniques -成型件工装效率评估技术217. Molded part tooling inventory management optimization -成型件工装库存管理优化218. Molded part tooling repair process efficiency evaluation -成型件工装修复流程效率评估219. Molded part tooling modification cost reduction strategies implementation -成型件工装修改成本降低策略实施220. Molded part tooling replacement cost reduction techniques implementation -成型件工装更换成本降低技术实施221. Molded part tooling storage space optimization strategies -成型件工装存储空间优化策略222. Molded part tooling transportation cost reduction techniques implementation -成型件工装运输成本降低技术实施223. Molded part tooling disposal methods optimization techniques -成型件工装处理方法优化技术224. Molded part tooling recycling process efficiency evaluation -成型件工装回收流程效率评估225. Molded part tooling cost analysis techniques implementation -成型件工装成本分析技术实施226. Molded part tooling design review process optimization strategies -成型件工装设计审查流程优化策略227. Molded part tooling production efficiency improvement techniques implementation -成型件工装生产效率提升技术实施228229. Molded part tooling quality control measures evaluation -成型件工装质量控制措施评估230. Molded part tooling inspection process optimization strategies -成型件工装检验过程优化策略231. Molded part tooling maintenance schedule development -成型件工装维护计划制定232. Molded part tooling repair cost analysis techniques -成型件工装修复成本分析技术233. Molded part tooling modification process efficiency improvement techniques implementation -成型件工装修改过程效率提升技术实施234. Molded part tooling replacement process cost reduction strategies implementation -成型件工装更换过程成本降低策略实施235. Molded part tooling storage system optimization -成型件工装存储系统优化236. Molded part tooling transportation cost analysis techniques implementation -成型件工装运输成本分析技术实施237. Molded part tooling disposal methods evaluation -成型件工装处理方法评估238. Molded part tooling recycling process efficiency improvement techniques implementation -成型件工装回收流程效率提升技术实施239. Molded part tooling cost reduction strategies evaluation -成型件工装成本降低策略评估240. Molded part tooling risk assessment techniques implementation -成型件工装风险评估技术实施241. Molded part tooling safety protocols optimization strategies -成型件工装安全协议优化策略242. Molded part tooling environmental impact assessment techniques implementation -成型件工装环境影响评估技术实施243. Molded part tooling sustainability improvement strategies evaluation -成型件工装可持续性改进策略评估244. Molded part tooling efficiency evaluation techniques implementation -成型件工装效率评估技术实施245. Molded part tooling inventory management optimization strategies implementation -成型件工装库存管理优化策略实施246. Molded part tooling repair process efficiency evaluation techniques -成型件工装修复流程效率评估技术247. Molded part tooling modification cost reduction strategies evaluation -成型件工装修改成本降低策略评估248. Molded part tooling replacement cost reduction techniques evaluation -成型件工装更换成本降低技术评估249. Molded part tooling storage space optimization strategies implementation -成型件工装存储空间优化策略实施250. Molded part tooling transportation cost reduction techniques evaluation -成型件工装运输成本降低技术评估251. Molded part tooling design optimization techniques implementation -成型件工装设计优化技术实施252. Molded part tooling production capacity evaluation -成型件工装生产能力评估253. Molded part tooling inspection methods improvement strategies -成型件工装检验方法改进策略254. Molded part tooling maintenance cost analysis techniques -成型件工装维护成本分析技术255. Molded part tooling repair process optimization strategies implementation -成型件工装修复过程优化策略实施256. Molded part tooling modification process cost reduction techniques -成型件工装修改过程成本降低技术257. Molded part tooling replacement process efficiency evaluation techniques -成型件工装更换过程效率评估技术258. Molded part tooling storage system efficiency improvement strategies implementation -成型件工装存储系统效率提升策略实施259. Molded part tooling transportation cost reduction strategies evaluation -成型件工装运输成本降低策略评估260. Molded part tooling disposal methods optimization techniques implementation -成型件工装处理方法优化技术实施261. Molded part tooling quality control measures implementation -成型件工装质量控制措施实施262. Molded part tooling material selection criteria evaluation -成型件工装材料选择标准评估263. Molded part tooling cost estimation techniques implementation -成型件工装成本估算技术实施264. Molded part tooling waste reduction strategies evaluation -成型件工装废料减少策略评估265. Molded part tooling energy consumption optimization techniques -成型件工装能源消耗优化技术266. Molded part tooling production cycle time reduction strategies evaluation -成型件工装生产周期缩短策略评估267. Molded part tooling training programs implementation -成型件工装培训计划实施268. Molded part tooling maintenance schedule optimization strategies -成型件工装维护计划优化策略269. Molded part tooling inspection frequency evaluation techniques -成型件工装检验频率评估技术270. Molded part tooling repair cost reduction strategies implementation -成型件工装修复成本降低策略实施271. Molded part tooling modification process efficiency evaluation techniques -成型件工装修改过程效率评估技术272. Molded part tooling replacement process cost reduction strategies -成型件工装更换过程成本降低策略273. Molded part tooling storage system organization techniques implementation -成型件工装存储系统组织技术实施274. Molded part tooling transportation safety protocols evaluation -成型件工装运输安全协议评估275. Molded part tooling disposal methods cost evaluation techniques -成型件工装处理方法成本评估技术276. Molded part tooling quality assurance audits implementation -成型件工装质量保证审计实施277. Molded part tooling material sourcing optimization strategies -成型件工装材料采购优化策略278. Molded part tooling cost control measures implementation -成型件工装成本控制措施实施279. Molded part tooling waste management techniques evaluation -成型件工装废料管理技术评估280. Molded part tooling energy efficiency improvement strategies -成型件工装能效提升策略281. Molded part tooling production planning optimization techniques implementation -成型件工装生产计划优化技术实施282. Molded part tooling training effectiveness evaluation techniques -成型件工装培训效果评估技术283. Molded part tooling maintenance cost reduction strategies evaluation -成型件工装维护成本降低策略评估284. Molded part tooling inspection methods optimization techniques -成型件工装检验方法优化技术285. Molded part tooling repair process cost reduction strategies implementation -成型件工装修复过程成本降低策略实施286. Molded part tooling modification process efficiency improvement techniques -成型件工装修改过程效率提升技术287. Molded part tooling replacement process safety protocols evaluation -成型件工装更换过程安全协议评估288. Molded part tooling storage system space optimization strategies -成型件工装存储系统空间优化策略289. Molded part tooling transportation cost analysis techniques implementation -成型件工装运输成本分析技术290. Molded part tooling disposal methods efficiency evaluation techniques -成型件工装处理方法效率评估技术291. Molded part tooling quality control system implementation -成型件工装质量控制系统实施292. Molded part tooling material selection process optimization strategies -成型件工装材料选择过程优化策略293. Molded part tooling cost estimation accuracy evaluation techniques -成型件工装成本估算准确度评估技术294. Molded part tooling waste reduction techniques implementation -成型件工装废料减少技295. Molded part tooling energy consumption monitoring system implementation -成型件工装能耗监测系统实施296. Molded part tooling production scheduling optimization strategies -成型件工装生产调度优化策略297. Molded part tooling training program development techniques -成型件工装培训计划开发技术298. Molded part tooling maintenance schedule optimization strategies -成型件工装维护计划优化策略299. Molded part tooling inspection frequency optimization techniques -成型件工装检验频率优化技术300. Molded part tooling repair process efficiency improvement strategies -成型件工装修复过程效率提升策略301. Molded part tooling replacement cost analysis techniques -成型件工装更换成本分析技术302. Molded part tooling storage system organization techniques -成型件工装存储系统组织技术303. Molded part tooling transportation safety protocols implementation -成型件工装运输安全协议实施304. Molded part tooling disposal methods cost analysis techniques -成型件工装处理方法成本分析技术305. Molded part tooling quality control system evaluation techniques -成型件工装质量控制系统评估技术306. Molded part tooling material selection process efficiency evaluation techniques -成型件工装材料选择过程效率评估技术307. Molded part tooling cost estimation accuracy improvement strategies -成型件工装成本估算准确度提升策略308. Molded part tooling waste management system implementation -成型件工装废料管理系统实施309. Molded part tooling energy consumption reduction techniques -成型件工装能耗减少技术310. Molded part tooling production scheduling efficiency evaluationtechniques -成型件工装生产调度效率评估技术311. Molded part tooling training program effectiveness evaluation techniques -成型件工装培训计划效果评估技术312. Molded part tooling maintenance schedule optimization techniques -成型件工装维护计划优化技术313. Molded part tooling inspection frequency optimization strategies -成型件工装检验频率优化策略314. Molded part tooling repair process cost analysis techniques -成型件工装修复过程成本分析技术315. Molded part tooling replacement process efficiency evaluation techniques -成型件工装更换过程效率评估技术316. Molded part tooling storage system space utilization techniques -成型件工装存储系统空间利用技术317. Molded part tooling transportation cost reduction strategies -成型件工装运输成本降低策略318. Molded part tooling disposal methods efficiency improvement strategies -成型件工装处理方法效率提升策略319. Molded part tooling quality control system implementation techniques -成型件工装质量控制系统实施技术320. Molded part tooling material selection process optimization techniques -成型件工装材料选择过程优化技术321. Molded part tooling cost estimation accuracy improvementtechniques -成型件工装成本估算准确度提升技术322. Molded part tooling waste reduction strategies implementation -成型件工装废料减少策略实施323. Molded part tooling energy consumption monitoring system optimization techniques -成型件工装能耗监测系统优化技术324. Molded part tooling production scheduling efficiency improvement strategies -成型件工装生产调度效率提升策略325. Molded part tooling training program development techniques -成型件工装培训计划开发技术326. Molded part tooling maintenance schedule optimization techniques -成型件工装维护计划优化技术327. Molded part tooling inspection frequency optimization strategies -成型件工装检验频率优化策略328. Molded part tooling repair process efficiency evaluation techniques -成型件工装修复过程效率评估技术329. Molded part tooling replacement cost analysis methods -成型件工装更换成本分析方法330. Molded part tooling storage system organization strategies -成型件工装存储系统组织策略331. Molded part tooling transportation safety protocols evaluation -成型件工装运输安全协议评估332. Molded part tooling disposal methods cost analysis methods -成型件工装处理方法成本分析方法333. Molded part tooling quality control system effectiveness evaluation techniques -成型件工装质量控制系统效果评估技术334. Molded part tooling material selection process efficiency improvement strategies -成型件工装材料选择过程效率提升策335. Molded part tooling cost optimization techniques -成型件工装成本优化技术336. Molded part tooling maintenance record keeping methods -成型件工装维护记录保持方法337. Molded part tooling inspection checklist development techniques -成型件工装检查清单开发技术338. Molded part tooling repair process time reduction strategies -成型件工装修复过程时间减少策略339. Molded part tooling replacement frequency analysis methods -成型件工装更换频率分析方法340. Molded part tooling storage system inventory management techniques -成型件工装存储系统库存管理技术341. Molded part tooling transportation route optimization strategies -成型件工装运输路线优化策略342. Molded part tooling disposal methods environmental impact assessment techniques -成型件工装处理方法环境影响评估技术343. Molded part tooling quality control system auditing methods -成型件工装质量控制系统审核方法344. Molded part tooling material selection process cost analysis techniques -成型件工装材料选择过程成本分析技术345. Molded part tooling cost estimation error analysis techniques -成型件工装成本估算误差分析技术346. Molded part tooling waste reduction strategies implementation monitoring techniques -成型件工装废料减少策略实施监测技术347. Molded part tooling energy consumption reduction techniques -成型件工装能耗减少技术348. Molded part tooling production scheduling optimization techniques -成型件工装生产调度优化技术349. Molded part tooling training program effectiveness evaluation methods -成型件工装培训计划效果评估方法350. Molded part tooling maintenance schedule flexibility strategies -成型件工装维护计划灵活性策略351. Molded part tooling design software proficiency assessment methods -成型件工装设计软件熟练度评估方法352. Molded part tooling cost reduction strategies implementation monitoring techniques -成型件工装成本降低策略实施监测技术353. Molded part tooling storage system space optimization strategies -成型件工装存储系统空间优化策略354. Molded part tooling transportation risk assessment methods -成型件工装运输风险评估方法355. Molded part tooling disposal methods regulatory compliance evaluation techniques -成型件工装处理方法合规性评估技术356. Molded part tooling quality control system training program development techniques -成型件工装质量控制系统培训计划开发技术357. Molded part tooling material selection process sustainability assessment methods -成型件工装材料选择过程可持续性评估方法358. Molded part tooling cost estimation accuracy improvement strategies -成型件工装成本估算准确性提升策略359. Molded part tooling waste management system implementation techniques -成型件工装废料管理系统实施技术360. Molded part tooling energy efficiency improvement strategies -成型件工装能效提升策略361. Molded part tooling production scheduling flexibility analysis methods -成型件工装生产调度灵活性分析方法362. Molded part tooling training program effectiveness evaluation criteria -成型件工装培训计划效果评估标准363. Molded part tooling maintenance schedule optimization techniques -成型件工装维护计划优化技术364. Molded part tooling design optimization methods for reducing defects -成型件工装设计优化方法降低缺陷365. Molded part tooling cost estimation techniques for new product development -成型件工装成本估算技术新产品开发366. Molded part tooling storage system inventory tracking methods -成型件工装存储系统库存跟踪方法367. Molded part tooling transportation risk mitigation strategies -成型件工装运输风险缓解策略368. Molded part tooling disposal methods environmental sustainability evaluation techniques -成型件工装处理方法环境可持续性评估技术369. Molded part tooling quality control system documentation management techniques -成型件工装质量控制系统文件管理技术370. Molded part tooling material selection process sustainability improvement strategies -成型件工装材料选择过程可持续性改善策略371. Molded part tooling cost estimation error reduction techniques -成型件工装成本估算误差减少技术372. Molded part tooling waste reduction strategies effectiveness evaluation methods -成型件工装废料减少策略效果评估方法373. Molded part tooling energy consumption monitoring techniques -成型件工装能耗监测技术374. Molded part tooling production scheduling optimization tools -成型件工装生产调度优化工具375. Molded part tooling training program evaluation methods -成型件工装培训计划评估方法376. Molded part tooling maintenance schedule adjustment techniques -成型件工装维护计划调整技术377. Molded part tooling design software selection criteria -成型件工装设计软件选择标准378. Molded part tooling cost reduction strategies effectiveness evaluation methods -成型件工装成本降低策略效果评估方法379. Molded part tooling storage system organization tools -成型件工装存储系统组织工具380. Molded part tooling transportation risk mitigation measures -成型件工装运输风险缓解措施381. Molded part tooling disposal methods regulatory compliance monitoring techniques -成型件工装处理方法合规性监测技术382. Molded part tooling quality control system training program evaluation methods -成型件工装质量控制系统培训计划评估方法383. Molded part tooling material selection process cost-benefit analysis techniques -成型件工装材料选择过程成本效益分析技术384. Molded part tooling waste management strategies sustainability assessment methods -成型件工装废料管理策略可持续性评估方法385. Molded part tooling energy efficiency improvement measures -成型件工装能效改善措施386. Molded part tooling production scheduling optimization algorithms-成型件工装生产调度优化算法387. Molded part tooling training program effectiveness evaluation tools -成型件工装培训计划效果评估工具388. Molded part tooling maintenance schedule optimization models -成型件工装维护计划优化模型389. Molded part tooling design optimization techniques for improving product performance -成型件工装设计优化技术提高产品性能390. Molded part tooling cost estimation methods for budget planning -成型件工装成本估算方法预算规划391. Molded part tooling storage system inventory management techniques -成型件工装存储系统库存管理技术392. Molded part tooling transportation risk assessment methods -成型件工装运输风险评估方法393. Molded part tooling disposal methods environmental impact assessment techniques -成型件工装处理方法环境影响评估技术394. Molded part tooling quality control system documentation control methods -成型件工装质量控制系统文件控制方法395. Molded part tooling material selection process sustainability evaluation criteria -成型件工装材料选择过程可持续性评估标准396. Molded part tooling cost estimation accuracy improvement techniques -成型件工装成本估算准确性改善技术397. Molded part tooling waste reduction strategies monitoring methods。
模具英语专业术语
模具英语专业术语如下：1. 模具：Mold，Die2. 模具设计：Mold Design3. 模具制造：Mold Manufacturing4. 模具工程师：Mold Engineer5. 模具材料：Mold Material6. 耐磨材料：wear-resistant material7. 热处理：Heat Treatment8. 水路设计：Water Path Design9. 浇注系统：Injection Sleeve10. 冷却系统：Cooling System11. 顶出系统：Pop-out System12. 复位系统：Reset System13. 导向机构：Guide Device14. 模板：Base Plate15. 顶杆：Pushrod16. 复位杆：Reset Rod17. 斜导柱：Oblique Guide Column18. 导套：Guide Bushing19. 滑块：Slider20. 镶针：Pillow Block21. 弹簧：Spring22. 皮囊弹簧：Kelvin Spring23. 油压缓冲器：Hydraulic Buffer24. 压力表：Pressure Gauge25. 安全阀：Safety Valve26. 水路板：Waterway Plate27. 分流器：Flow Divider28. 水口：Filler Port29. 冷料穴：Cold Molding Chamber30. 模具钢：Mold Steel31. SKH-55、SKH-55M、高速工具钢、HSS等。
32. SKD、SKH-S、SKD61、SKH-9等。
模具钢硬度（Hardness of die steel）：布氏硬度（HB）、洛氏硬度（HRC）、维氏硬度（HV）等。
33. SKD61(级硬SKD61) ，Cr12MoV，A3，A2，SKH-9，718，738，P20等。
塑料模具钢有PXZ、SACD、S136、S718、SS446、3Cr2Mo等。
模具专业英语词汇
模具专业英语词汇摘要：模具是一种用于生产特定形状的产品的工具，它在制造业中有着广泛的应用。
模具专业英语词汇是指与模具相关的专业术语，它涉及到模具的设计、制造、检验、使用等方面。
本文根据不同的主题，整理了一些常用的模具专业英语词汇，并用表格的形式进行了展示，以便于读者学习和参考。
1. 模具类型模具是一种用于生产特定形状的产品的工具，它可以分为不同的类型，根据加工方法和材料的不同，可以分为以下几类：中文英文注塑模injection mold压铸模die-casting mold冲压模stamping mold挤出模extrusion mold吹塑模blow mold硅胶模silicone mold砂型模sand mold石膏模plaster mold三板模three-plate mold双色模two-color mold2. 模具结构模具结构是指模具的组成部分和连接方式，它决定了模具的功能和性能。
一般来说，一个完整的模具由以下几个部分组成：中文英文模架mold base模芯core模腔cavity浇口系统gate system导向系统guiding system顶出系统ejection system冷却系统cooling system3. 模架模架是指支撑和固定模芯、模腔等部件的基础结构，它通常由标准件或定制件组成。
常见的模架部件有：中文英文定模座板fixed clamping plate动模座板moving clamping plate定模套板fixed bolster plate动模套板moving bolster plate支承板backing plate垫块spacer block4. 模芯和模腔模芯和模腔是指与被加工材料直接接触并形成产品形状的部件，它们通常由钢材或其他硬质材料制成。
常见的与模芯和模腔相关的术语有：中文英文凹面（内型面）concave surface (inner surface)凸面（外型面）convex surface (outer surface)分型面（合型面）parting surface (matching surface)型芯固定板（凸模固定板）core-retainer plate (punch-retainer plate)凹模固定板（凸模固定板）cavity-retainer plate (die-retainer plate)5. 浇口系统浇口系统是指将熔融或液态材料从注塑机或压铸机输送到型腔中的通道，它包括浇口、流道、冷料井等部件。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口：pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker 四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝：screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位（滑块）：slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch模具钢材行业的相关英语单词汇总塑件&模具compre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具（移转成型用模具）encapsulation molding 低压封装成型（射出成型用模具）two plate 两极式（模具）well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spindle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道welding line 熔合痕eject pin 顶出针knock pin 顶出销return pin 回位销反顶针sleave 套筒stripper plate 脱料板insert core 放置入子runner stripper plate 浇道脱料板guide pin 导销eject rod (bar)（成型机）顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orientation 定向sprue gate 射料浇口，直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆) slag well 冷料井side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口subarine gate 潜入式浇口tunnel gate 隧道式浇口pin gate 针点浇口Runner less 无浇道(sprue less) 无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming 泡沫成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模transfer die连续自动冲切,连续冲模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingotmold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁) cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧楔goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶头冲孔headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶销lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑胶模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导销pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 托料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱销stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 托板sweep templete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板工作机械3D coordinate measurement 三次元量床boring machine 搪孔机cnc milling machine CNC铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床copy lathe 仿形车床copy milling machine 仿形铣床copy shaping machine 仿形刨床cylindrical grinding machine 外圆磨床die spotting machine 合模机drilling machine 冲孔机engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindrical machine 内圆磨床jig boring machine 冶具搪孔机jig grinding machine 冶具磨床lap machine 研磨机machine center 加工制造中心multi model miller 靠磨铣床NC drilling machine NC钻床NC grinding machine NC磨床NC lathe NC车床NC programming system NC程序制作系统planer 龙门刨床profile grinding machine 投影磨床projection grinder 投影磨床radial drilling machine 旋臂钻床shaper 牛头刨床surface grinder 平面磨床try machine 试模机turret lathe 转塔车床universal tool grinding machine 万能工具磨床vertical machine center 立式加工制造中心wire E.D.M. 线割放电加工机模具加工方法barrel 滚筒(加工) bending 波纹加工broaching 拉刀切削centering 定中心cutting 切削cylindrical lathe cutting 外圆车削electric discharge machine 放电加工electrolytic grinding 电解研磨embossing 压花加工facing 面车削filing 锉刀修润hand finishing 手工修润hemming 卷边加工hobbing 滚齿加工joggling 摇动加工lapping 抛光/研磨修润laser beam machining 雷射加工lathe cutting 车床车削planning 刨削加工polishing 抛亮光reaming 铰孔修润rough machining 粗切削rounding 圆形加工sawing 锯削scaling 清除钢碇缺陷shaping 成形加工skiving 表面研磨slotting 切缝切削taper turning 锥度车削thread cutting 螺纹切削ultrasonic machining 超音波加工up cut milling 逆铣加工机床常用词汇punching machine 冲床robot机械手hydraulic machine油压机lathe车床|刨床?planer |'plein miller铣床grinder磨床driller钻床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架冲压模具的零部件punch 冲压模具的冲头insert 冲压模具的入块(嵌入件) deburring punch 冲压模具的压毛边冲子groove punch 冲压模具的压线冲子stamped punch 冲压模具的字模冲子round punch 冲压模具的圆冲子special shape punch 冲压模具的异形冲子bending block 冲压模具的折刀roller 冲压模具的滚轴baffle plate 冲压模具的挡块located block 冲压模具的定位块supporting block forlocation 冲压模具的定位支承块air cushion plate 冲压模具的气垫板air-cushion eject-rod 冲压模具的气垫顶杆trimming punch 冲压模具的切边冲子stiffening rib punch = stinger 冲压模具的加强筋冲子ribbon punch 冲压模具的压筋冲子reel-stretch punch 冲压模具的卷圆压平冲子guide plate 冲压模具的定位板sliding block 冲压模具的滑块sliding dowel block 冲压模具的滑块固定块active plate 冲压模具的活动板lower sliding plate 冲压模具的下滑块板upper holder block 冲压模具的上压块upper mid plate 冲压模具的上中间板spring box 冲压模具的弹簧箱spring-box eject-rod 冲压模具的弹簧箱顶杆spring-box eject-plate 冲压模具的弹簧箱顶板bushing bolck 冲压模具的衬套cover plate 冲压模具的盖板砂轮用词汇abrasive 砂轮Al2O3 氧化铝borazon 氧化硼立方晶buffing wheel 抛光布轮diamond 钻石dresser 砂轮整修机dressing 修整endless grinding belt 循环式研磨带finishing allowance 加工余量grain 磨粒grinding disc 研磨盘jamp up 孔眼堵塞mesh 网筛目resinoid grinding wheel 半树脂型砂轮slitting 切缝量vitrified 陶瓷的wheel 旋转热处理常用英文词汇indication 缺陷test specimen 试样bar 棒材stock 原料billet 方钢，钢方坯bloom 钢坯,钢锭section 型材steel ingot 钢锭blank 坯料，半成品cast steel 铸钢nodular cast iron 球墨铸铁ductile cast iron 球墨铸铁bronze 青铜brass 黄铜copper 合金stainless steel不锈钢decarburization 脱碳scale 氧化皮anneal 退火process anneal 进行退火quenching 淬火normalizing 正火Charpy impact text 夏比冲击试验fatigue 疲劳tensile testing 拉伸试验solution 固溶处理aging 时效处理Vickers hardness维氏硬度Rockwell hardness 洛氏硬度Brinell hardness 布氏硬度hardness tester硬度计descale 除污，除氧化皮等ferrite 铁素体austenite 奥氏体martensite马氏体cementite 渗碳体iron carbide 渗碳体solid solution 固溶体sorbite 索氏体bainite 贝氏体pearlite 珠光体nodular fine pearlite/ troostite屈氏体black oxide coating 发黑grain 晶粒chromium 铬cadmium 镉tungsten 钨molybdenum 钼manganese 锰vanadium 钒molybdenum 钼silicon 硅sulfer/sulphur 硫phosphor/ phosphorus 磷nitrided 氮化的case hardening 表面硬化，表面淬硬air cooling 空冷furnace cooling 炉冷oil cooling 油冷electrocladding /plating 电镀brittleness 脆性strength 强度rigidity 刚性,刚度creep 蠕变deflection 挠度elongation 延伸率yield strength 屈服强度elastoplasticity 弹塑性metallographic structure 金相组织metallographic test 金相试验carbon content 含碳量induction hardening 感应淬火impedance matching 感应淬火hardening and tempering 调质crack 裂纹shrinkage 缩孔，疏松forging 锻（件）casting 铸（件）rolling 轧（件）drawing 拉（件）shot blasting 喷丸（处理）grit blasting 喷钢砂（处理）sand blasting 喷砂（处理）carburizing 渗碳nitriding 渗氮ageing/aging 时效grain size 晶粒度pore 气孔sonim 夹砂cinder inclusion 夹渣lattice晶格abrasion/abrasive/rub/wear/wearing resistance (property) 耐磨性spectrum analysis 光谱分析heat/thermal treatment 热处理inclusion 夹杂物segregation 偏析picking 酸洗，酸浸residual stress 残余应力remaining stress 残余应力relaxation of residual stress 消除残余应力stress relief 应力释放常用塑料英语缩略语英文简称英文全称中文全称A BA Acrylonitrile-butadiene-acrylate 丙烯腈/丁二烯/丙烯酸酯共聚物A BS Acrylonitrile-butadiene-styrene 丙烯腈/丁二烯/苯乙烯共聚物A ES Acrylonitrile-ethylene-styrene 丙烯腈/乙烯/苯乙烯共聚物AMMA Acrylonitrile/methyl Methacrylate 丙烯腈/甲基丙烯酸甲酯共聚物A RP Aromatic polyester 聚芳香酯AS Acrylonitrile-styrene resin 丙烯腈-苯乙烯树脂ASA Acrylonitrile-styrene-acrylate 丙烯腈/苯乙烯/丙烯酸酯共聚物CA Cellulose acetate 醋酸纤维塑料CAB Cellulose acetate butyrate 醋酸-丁酸纤维素塑料CAP Cellulose acetate propionate 醋酸-丙酸纤维素CE Cellulose plastics, general 通用纤维素塑料CF Cresol-formaldehyde 甲酚-甲醛树脂CMC Carboxymethyl cellulose 羧甲基纤维素CN Cellulose nitrate 硝酸纤维素CP Cellulose propionate 丙酸纤维素CPE Chlorinated polyethylene 氯化聚乙烯CPVC Chlorinated poly(vinyl chloride) 氯化聚氯乙烯CS Casein 酪蛋白CTA Cellulose triacetate 三醋酸纤维素EC Ethyl cellulose 乙烷纤维素EMA Ethylene/methacrylic acid 乙烯/甲基丙烯酸共聚物EP Epoxy, epoxide 环氧树脂EPD Ethylene-propylene-diene 乙烯-丙烯-二烯三元共聚物EPM Ethylene-propylene polymer 乙烯-丙烯共聚物EPS Expanded polystyrene 发泡聚苯乙烯ETFE Ethylene-tetrafluoroethylene 乙烯-四氟乙烯共聚物EV A Ethylene/vinyl acetate 乙烯-醋酸乙烯共聚物EV AL Ethylene-vinyl alcohol 乙烯-乙烯醇共聚物FEP Perfluoro(ethylene-propylene) 全氟（乙烯-丙烯）塑料FF Furan formaldehyde 呋喃甲醛HDPE High-density polyethylene plastics 高密度聚乙烯塑料HIPS High impact polystyrene 高冲聚苯乙烯IPS Impact-resistant polystyrene 耐冲击聚苯乙烯LCP Liquid crystal polymer 液晶聚合物LDPE Low-density polyethylene plastics 低密度聚乙烯塑料LLDPE Linear low-density polyethylene 线性低密聚乙烯LMDPE Linear medium-density polyethylene 线性中密聚乙烯MBS Methacrylate-butadiene-styrene 甲基丙烯酸-丁二烯-苯乙烯共聚物MC Methyl celluloseMDPE Medium-density polyethylene 中密聚乙烯MF Melamine-formaldehyde resin 密胺-甲醛树脂MPF Melamine/phenol-formaldehyde 密胺/酚醛树脂PA Polyamide (nylon) 聚酰胺（尼龙）PAA Poly(acrylic acid) 聚丙烯酸PADC Poly(allyl diglycol carbonate) 碳酸-二乙二醇酯• 烯丙醇酯树脂PA E Polyarylether 聚芳醚PA EK Polyaryletherketone 聚芳醚酮PAI Polyamide-imide 聚酰胺-酰亚胺PAK Polyester alkyd 聚酯树脂PAN Polyacrylonitrile 聚丙烯腈PA RA Polyaryl amide 聚芳酰胺PASU Polyarylsulfone 聚芳砜PAT Polyarylate 聚芳酯PAUR Poly(ester urethane) 聚酯型聚氨酯PB Polybutene-1 聚丁烯-[1]PBA Poly(butyl acrylate) 聚丙烯酸丁酯PBA N Polybutadiene-acrylonitrile 聚丁二烯-丙烯腈PBS Polybutadiene-styrene 聚丁二烯-苯乙烯PBT Poly(butylene terephthalate) 聚对苯二酸丁二酯PC Polycarbonate 聚碳酸酯PCTFE Polychlorotrifluoroethylene 聚氯三氟乙烯PDAP Poly(diallyl phthalate) 聚对苯二甲酸二烯丙酯PE Polyethylene 聚乙烯PEBA Polyether block amide 聚醚嵌段酰胺PEBA Thermoplastic elastomer polyether 聚酯热塑弹性体PEEK Polyetheretherketone 聚醚醚酮PEI Poly(etherimide) 聚醚酰亚胺PEK Polyether ketone 聚醚酮PEO Poly(ethylene oxide) 聚环氧乙烷PES Poly(ether sulfone) 聚醚砜PET Poly(ethylene terephthalate) 聚对苯二甲酸乙二酯PETG Poly(ethylene terephthalate) glycol 二醇类改性PET PEUR Poly(ether urethane) 聚醚型聚氨酯PF Phenol-formaldehyde resin 酚醛树脂PFA Perfluoro(alkoxy alkane) 全氟烷氧基树脂PFF Phenol-furfural resin 酚呋喃树脂PI Polyimide 聚酰亚胺PIB Polyisobutylene 聚异丁烯PISU Polyimidesulfone 聚酰亚胺砜PMCA Poly(methyl-alpha-chloroacrylate) 聚α-氯代丙烯酸甲酯PMMA Poly(methyl methacrylate) 聚甲基丙烯酸甲酯PMP Poly(4-methylpentene-1) 聚4-甲基戊烯-1PMS Poly(alpha-methylstyrene) 聚α-甲基苯乙烯POM Polyoxymethylene, polyacetal 聚甲醛PP Polypropylene 聚丙烯PPA Polyphthalamide 聚邻苯二甲酰胺PPE Poly(phenylene ether) 聚苯醚PPO Poly(phenylene oxide) deprecated 聚苯醚PPOX Poly(propylene oxide) 聚环氧（丙）烷PPS Poly(phenylene sulfide) 聚苯硫醚PPSU Poly(phenylene sulfone) 聚苯砜PS Polystyrene 聚苯乙烯PSU Polysulfone 聚砜PTFE Polytetrafluoroethylene 聚四氟乙烯PUR Polyurethane 聚氨酯PV A C Poly(vinyl acetate) 聚醋酸乙烯PV A L Poly(vinyl alcohol) 聚乙烯醇PVB Poly(vinyl butyral) 聚乙烯醇缩丁醛PVC Poly(vinyl chloride) 聚氯乙烯PVCA Poly(vinyl chloride-acetate) 聚氯乙烯醋酸乙烯酯PVDC Poly(vinylidene chloride) 聚（偏二氯乙烯）PVDF Poly(vinylidene fluoride) 聚（偏二氟乙烯）PVF Po ly(vinyl fluoride) 聚氟乙烯PVFM Poly(vinyl formal) 聚乙烯醇缩甲醛PVK Polyvinylcarbazole 聚乙烯咔唑PVP Polyvinylpyrrolidone 聚乙烯吡咯烷酮S/MA Styrene-maleic anhydride plastic 苯乙烯-马来酐塑料SA N Styrene-acrylonitrile plastic 苯乙烯-丙烯腈塑料SB Styrene-butadiene plastic 苯乙烯-丁二烯塑料Si Silicone plastics 有机硅塑料SMS Styrene/alpha-methylstyrene plastic 苯乙烯-α-甲基苯乙烯塑料SP Saturated polyester plastic 饱和聚酯塑料SRP Styrene-rubber plastics 聚苯乙烯橡胶改性塑料TEEE Thermoplastic Elastomer,Ether-Ester 醚酯型热塑弹性体TEO Thermoplastic Elastomer, Olefinic 聚烯烃热塑弹性体TES Thermoplastic Elastomer, Styrenic 苯乙烯热塑性弹性体TPEL Thermoplastic elastomer 热塑(性)弹性体TPES Thermoplastic polyester 热塑性聚酯TPUR Thermoplastic polyurethane 热塑性聚氨酯TSUR Thermoset polyurethane 热固聚氨酯UF Urea-formaldehyde resin 脲甲醛树脂UHMWPE Ultra-high molecular weight PE 超高分子量聚乙烯UP Unsaturated polyester 不饱和聚酯VCE Vinyl chloride-ethylene resin 氯乙烯/乙烯树脂VCEV Vinyl chloride-ethylene-vinyl 氯乙烯/乙烯/醋酸乙烯共聚物VCMA Vinyl chloride-methyl acrylate 氯乙烯/丙烯酸甲酯共聚物VCMMA Vinyl chloride-methylmethacrylate 氯乙烯/甲基丙烯酸甲酯共聚物VCOA Vinyl chloride-octyl acrylate resin 氯乙烯/丙烯酸辛酯树脂VCV A C Vinyl chloride-vinyl acetate resin 氯乙烯/醋酸乙烯树脂VCVDC Vinyl chloride-vinylidene chloride 氯乙烯/偏氯乙烯共聚物。