海立压缩机规格书-WHP03500RCV-G7BUN
- 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。
目录
一、WHP03500RCV-G7BUN规格书 —————1~4
1.应用范围
2.压缩机规格
3.零件及图纸清单
4.一般特性
二、热泵热水器专用压缩机使用基准 ———5~12
1.系统设计限制
2.工艺限制
3.其他
三、验收 ———————13
1.验收依据
2.验收规则
四、图纸 ———————14~25
WHP03500RCV-G7BUN规格书
1. SCOPE 应用范围
This specification is applied to SHANGHAI HITACHI Heat pump water heater compressor. 此规格适用于上海日立电器有限公司生产的热泵热水器专用压缩机。
2. SPECIFICATION OF COMPRESSOR 压缩机规格
2.1 Model
型号 WHP03500RCV-G7BUN
2.2 Rated Voltage/Frequency/Phase 220-240V/50Hz/single
额定电压/频率/相数 220-240V/50Hz/单相
2.3 Application Heat pump water heater
应用 热泵热水器
2.4 Refrigerant
制冷剂 R-22
2.5 Compressor Cooling Forced air
压缩机冷却 强制空冷
2.6 Displacement
排气量 16.2ml/rev
2.7 Performance性能参数
Performance (Voltage 220V)
性能参数 (电压 220V)
Item 项目 Standard Condition标
准工况
Summer Condition
夏季工况
Winter Condition
冬季工况
Rated Condition
额定工况
Nominal Heating
Capacity
名义制热量
3790W 4360W 2880W 3520W
Motor input
电机输入功率
890W 890W 860W 870W
Current
电流
4.30A 4.30A 4.10A 4.10A
COP(see*)
能效比(见*)
4.26 4.90 3.35 4.05
Test Conditions测试条件
Evaporating temp.
蒸发温度 10℃ 15℃ 0℃ 7.2℃
Condensing temp.
冷凝温度 55℃ 55℃ 55℃ 54.4℃
Liquid temp.
entering
expansion valve.
膨胀阀前液体温度
46.7℃ 46.7℃ 46.7℃ 46.7℃
Return gas temp.
回气温度 20℃ 25℃ 10℃ 35℃
Ambient temp.
周围温度 35℃ 35℃ 15℃ 35℃
Wind speed
风速2m/s 2m/s2m/s2m/s
WHP03500RCV-G7BUN规格书
Heating capacity 名义制热量 (W)
* COP=
Motor input 电机输入功率 (W)
2.8 Allowable amount of
refrigerant charge
制冷剂充注允许量 1100 g
2.9 Amount of oil charge 350±10 ml(Initial)
油充注允许量 350±10 ml(最初)
2.10 Oil 4GSI or equivalent
油 4GSI或者SHEC指定同类冷冻机油
2.11 Space volume of inner case
壳体内容积 1260 ml
2.12 Net weight 11.8 kg incl.oil
净重 11.8kg 包括油
2.13 Hermetic Terminal 1/4”quick connect type
密封接线柱 1/4” 快速连接型
2.14 Motor
Type Permanent Split Capacitor
Capacitor 35MFD/450 Volts
Locked rotor amps 21A (240V/50Hz)
Approved voltage range Rated Voltage(-10%,+10%)
Winding resistance(M/S) 3.74Ω/3.72Ω(at 20℃)
电机
形式 PSC
电容器 35μF/450 V
堵转电流 21A (240V/50Hz)
电压变动范围 额定电压(-10%,+10%)
电阻(主线圈/副线圈) 3.74Ω/3.72Ω(at 20℃)
2.15 Starting performance (1) The starting voltage should be as follows.
(2) The starting pressure should be balanced
between the suction and discharge of the
compressor and should be adjusted to the
following table.
(3) The temperatures of the compressor encl-
osure should be more than 20℃continuously at the following table.