汽车专业英语4-1
《汽车专业英语》word版
齿轮副gear pair平行轴齿轮副gear pair with parallel axes 相交轴齿轮副gear pair with intersecting axles交错轴齿轮副gear pair with non-parallel齿轮系gear train复合行星齿轮系compound planetary gear train配对齿轮mating gears小齿轮pinion大齿轮wheel行星齿轮planet gear行星架planet carrier太阳轮sun gear内齿圈ring gear外齿轮external gear内齿轮internal gear减速齿轮副speed reducing gear pair 增速齿轮副speed increasing gear train 中心距centre distance轴交角shaft angle连心线line of centres齿数比gear ratio传动比transmission ratio 减速比speed reducing ratio 参考平面reference planes轴平面axial plane基准平面datum plane节平面pitch plane端平面transverse plane法平面normal plane遐想曲面imaginary srufaces 分度曲面reference surface节曲面pitch surface齿顶曲面tip surface齿根曲面root surface基本齿廓basic rack tooth profile 产形齿条counterpart rack基准线datum line轮齿特性teeth characteristics 轮齿gear齿槽tooth space右旋齿right-hand teeth左旋齿left-hand teeth齿面tooth flank右侧齿面right flank左侧齿面left flank同侧齿面corresponding flanks 异侧齿面opposite flanks工作齿面working flank非工作齿面non-working flank 相齿齿面mating flank可用齿面rsable flank有效齿面active flank上齿面addendum flank 下齿面dedendum flank 齿根过渡曲面fillet齿顶面crest top land齿槽底面〔槽底〕bottom land齿廓tooth profile端面齿廓transverse profile 法向齿廓normal profile轴向齿廓axial profile齿线tooth trace齿棱tip surface模数module端面模数transverse module法面模数normal module轴向模数axial module径节diametral pitch当量齿数virtual number of teeth 头数number of threads螺旋线helix and spirals圆锥螺旋线conical spiral螺旋角helix angle导程lead导程角lead angle摆线trochoids外摆线eqicycloid圆心渐开线involute to a circle 延伸渐开线prolate involute 螺旋面helicoid干涉interference修形correction of the flank shape 修像tip relief修根root relief齿面修形axial modification齿端修薄end relief鼓形修整crowning挖根undercut瞬时轴instantaneous axis啮合engagement mesh端面啮合线transverse path of contact啮合齿面surface of action啮合平面plane of action重合度contact ratio and overlap ratio 总作用弧total arc of transmission纵向作用弧overlap arc总作用角total angle of transmission径向变位系数overlap arc圆程齿轮和圆柱齿轮副ckyclindrical gears and gear pairs 齿条rack直齿轮spur gear斜齿轮helical gear直齿条spur rack大字齿轮double-helical gear渐开线齿轮involute cylindrical gear 圆弧圆柱齿轮circular -arc gear分度圆柱面reference cylinder节圆柱面pitch cylinder基圆柱面base cylinder齿顶圆柱面tip cylinder齿根圆柱面root cylinder节点pitch point分度圆pitch line节圆pitch circle基圆base circle齿顶圆〔顶圆〕tip circle齿根圆〔根圆〕root circle法向螺旋线normal helix齿距pitch齿距角angular pitch公法线总长base tangent length分度圆直径reference diameter 齿高tooth depth齿宽face width齿顶高dedendum齿根高dedendum弦齿高chordal height固定弦齿高constant cord height 齿厚tooth thickness惊险电影thriller movie电影院常客cinemogoer以惊险的谋杀疑案为主线thriller nuder mystery at its heart 顶隙bottom clearance圆周侧隙circumferential backlash法向侧隙normal backlash径向侧隙radial backlash锥齿轮bevel gear锥齿轮副bevel gear pair准双曲面齿轮副hypoid gear pair冠轮crown gear端面齿盘contrate gear直齿锥齿轮straight bevel gear斜齿锥齿轮helical bevel gear曲线齿锥齿轮spiral bevel gear弧齿锥齿轮gleason spiral bevel gear 摆线齿锥齿轮overlikon spiral bevel gear 零度锥齿轮zerol bevel gear分度圆锥面reference cone分度圆reference circle分锥顶点reference cone apex外锥距outer cone distance分度圆直径reference diameter齿高tooth depth齿顶高addendum齿根高dedendum工作高度working depth弦齿高chordal height齿距pitch齿距pitch齿厚tooth thickness弦齿厚chordal tooth thickness齿槽宽space width齿宽face width安装距locating distance轮冠距tip distance冠顶距apex to crown顶隙bottom clearance分度圆锥角reference cone angle 齿顶角addendum angle齿根角dedendum angle压力角pressure angle齿厚半角tooth thickness half angle槽宽半角apace width half angle轮椅升降机Wheel chair lift图例legend工位station吊运装置overhead hoist更衣室restroom1号厂房工艺布置方案图proposal of the Plant I layout 合笼mate底盘平移台chassis shuttle车辆转移台bus transfer前围角板front wall angle cover后围侧板rear wall side cover保险杠bumper三类底盘three type chassis左侧围应力蒙皮R/S stretching skin <road side>中涂floating coat拼装台collector切割轮口wheel -arch cutting内饰trim线束harness返工re-doing轮罩护板wheel house发车前准备pre-delivery举升hoist小批量产品be pilot2 套two kits配电站power transformer substation裙板skirt发动机托架engine holding frame诊断报警系统diagnosis and alarming system 互换性interchangeability缩微图纸microfiche files总装final assembly磷化phosphating仪表板dash board切齐trimming结构完整性structure integrity自动愈合的防腐材料self-healing corrosion preventative material 长途客车inter-city bus改装厂refitting factory遮阳板sun visor随车工具tool box钢化玻璃toughened grass异形钢管special steel pipe全天候空调系统full range A/C强制通风ram-air ventilation停机时间downtime无公害柴油clean diesel宽敞悬臂式座椅roomy cantilevered seat防滑地板no-skid floor织物纹里铝合金textured aluminum extrution爬坡能力grade ability排水阀drain valve除湿器moisture ejector怠速时at idle琴式驱动桥banjo type drive axle通风口duct恒温控制thermostatic control平衡水箱surge tank变光开关simmer switch消音器muffler防破坏vandal resistant聚碳化透镜poly-carbonate len镀锌板galvanized plate搭接lap亮丽的外表smart apperance隐藏式固定concealed fastening水洼ponding发动机中置式客车bus with under floor engine 组合式客车车身modular bus body薄壳式结构shell construction衬垫pad空气导流板air deflector搁梁shelf beam腰梁waist rail梭梁stabilizing beam腰带式安全带diagonal safety belt压条trim strip嵌条insertion strip翼板fender斜撑bracing piece转向盘回正性试验test of steering wheel returnability转向盘转角脉冲试验steering wheel impulse input test转向盘转角阶跃输入试验steering wheel step input or transient state yaw response test极限侧向加速度试验limiting lateral acceleration test汽车平顺性随机输入行驶试验automobile ride random input running test汽车平顺性单脉冲输入行驶试验automobile ride single pulse input running test 汽车悬挂系统固有频率与阻尼比的测定试验measurement of natural frequency and damping raito of suspension功率突然变化影响试验test of effect of sudden power change收油门后控制试验test of control at breakway横风稳定性试验test of crosswind stability反冲试验kick-back test轮胎爆破响应时间试验test of burst response of tyre绕过障碍物试验obstacle avoidance test移线试验lane change testJ型转弯试验test of J turn频率响应时间试验frequency response test瞬态响应时间试验transient response test阶路响应时间试验step response test脉冲响应试验pulse response test静态操舵力试验static steering effort test悬架举升试验jack-up test of suspension耐翻倾试验test of overturning immunity轮辋错动试验rim slip test风洞试验wind tunnel test制动稳定性试验test of braking stability最小转弯直径试验minimum turning diameter test 操舵力试验steering effort test汽车发动机类型type发动机engine内燃机intenal combusiton engine动力机装置power unit汽油机gasoline engine汽油喷射式汽油机gasoline-injection engine火花点火式发动机spark ignition engine压燃式发动机compression ignition engine往复式内燃机reciprocating internal combustion engine 化油器式发动机carburetor engine柴油机diesel engine转子发动机rotary engine旋轮线转子发动机rotary trochoidal engine二冲程发动机two-stroke engine四冲程发动机four-stroke engine直接喷射式柴油机direct injection engine间接喷射式柴油机indirect injection engine增压式发动机supercharged engine风冷式发动机air-cooled engine油冷式发动机oil-cooled engine水冷式发动机water-cooled engine自然进气式发动机naturally aspirated engine煤气机gas engine液化石油气发动机liquified petroleum gas engine柴油煤气机diesel gas engine多种燃料发动机multifuel engine石油发动机hydrocarbon engine双燃料发动机duel fuel engine热球式发动机hot bulb engine多气缸发动机multiple cylinder engine 对置活塞发动机opposed piston engine 对置气缸式发动机opposed-cylinder engine 十字头型发动机cross head engine直列式发动机in-line engine星型发动机radial engine筒状活塞发动机trunk-piston engine斯特林发动机stirling engine套阀式发动机knight engine气孔扫气式发动机port-scavenged engine 倾斜式发动机slant engine前置式发动机front-engine后置式发动机rear-engine中置式发动机central engine左侧发动机left-hand engine右侧发动机right-hand engine短冲程发动机oversquare engine长冲程发动机undersquare engine等径程发动机square engine顶置凸轮轴发动机overhead camshaft engine双顶置凸轮轴发动机dual overhead camshaft engine V形发动机V-engine顶置气门发动机valve in-head engine侧置气门发动机side valve engine无气门发动机valveless engine多气门发动机multi-valve engine 卧式发动机horizontal engine 斜置式发动机inclined engine立式发动机vertical engineW形发动机w-engineI形发动机I-engineL形发动机L-engineF形发动机F-engine性能performance二冲程循环two-stroke cycle四冲程循环four-stroke cycle狄塞尔循环diesel cycle奥托循环otto cycle混合循环mixed cycle定容循环constant volume cycle 工作循环working cycle等压循环constant pressure cycle 理想循环ideal cycle热力循环thermodynamic cycle 冲程stroke活塞行程piston stroke长行程long stroke上行程up stroke下行程down stroke进气行程intake stroke充气行程charging stroke压缩行程compression stroke 爆炸行程explosion stroke膨胀行程expansion stroke 动力行程power stroke排气行程exhaust stroke膨胀换气行程expansion-exchange stroke换气压缩行程exchange-compression stroke止点dead center上止点top dead center<upper dead center>下止点lower dead center<bottom dead center> 上止点前budc<before upper dead center>上止点后atdc<after top dead cetner>下止点前bbdc<before bottom dead center>下止点后abdc<after bottom dead center>缸径cylinder bore缸径与行程bore and stroke空气室energy chamber气缸余隙容积cylinder clearance volume燃烧室容积combustion chamber volume 气缸最大容积maximum cylinder volume 压缩室compression chamber排气量displacement发动机排量engine displacement活塞排量piston swept volume气缸容量cylinder capacity单室容量single-chamber capacity 容积法volumetry压缩比compression ratio临界压缩比critical compression ratio 膨胀比expansion ratio面容比surface to volume ratio 行程缸径比stroke-bore ratio混合比mixture ratio压缩压力compression pressure制动平均有效压力brake mean effective pressure<bmep> 空燃比air fuel ratio燃空比fuel air ratio燃料当量比fuel equivalence ratio扭矩torque单缸功率power per cylinder升功率power per liter升扭矩torque per liter升质量mass per liter减额功率derating power输出马力shaft horsepower马力小时,马力时horsepower-hour总马力gross horse power总功率gross power净功率net power燃油消耗量fuel consumption比燃料消耗率specific fuel consumption 空气消耗率air consumption机油消耗量oil consumption有效马力net horse power额定马力rated horse power马力重量系数horsepower-weight factor 制动功率brake horse power制动热效率brake thermal efficiency总效率overall efficiency排烟极限功率smoke limiting horsepower 功率曲线power curve机械损失mechanical loss机械效率mechanical efficiency有效热效率effective thermal efficiency充气系数volumetric efficiency过量空气系数coefficient of excess air适应性系数adaptive coefficient扭矩适应性系数coefficient of torque adaptibility 转速适应性系数speed adaptive coefficient强化系数coefficient of intensification校正系数correction factor换算系数conversion factor活塞平均速度mean piston speed发动机转速engine speed <rotational frequency> 怠速转速idling speed经济转速economic speed起动转速starting speed最低稳定工作转速lowest continuous speed with load 最大扭矩转速speed at maximum torque最高空转转速maximum no load governed speed 调速speed governing超速overspeed怠速idling转速波动率speed fluctuation rate工况working condition<operating mode> 额定工况declared working condition变工况variable working condition稳定工况steady working condition空载no-load全负荷full load超负荷overload部分负荷part load充量〔进气〕charge旋转方向direction of rotation 顺时针clockwise逆时针counter-clockwise 左转left-hand rotation 右转right-hand rotation 外径major diameter中径pitch diameter内径minor diameter径向间隙radial clearance发动机性能engine performance 加载性能loading performance起动性能starting performance加速性能acceleration performance动力性能power performance排放性能emission performance空转特性no load characteristics负荷特性part throttle characteristics调速特性governor control characteristics 万有特性mapping characteristics稳定调速率steady state speed governing rate 气缸体和气缸盖cylinder block and head气缸体cylinder block整体铸造cast inblock <cast enblock> 发动机罩engine bonnet气缸体加强筋engine block stiffening rib 气缸cylinder〔转子机〕缸体stator缸径cylinder bore气缸体机架cylinder block frame气缸盖cylinder head配气机构箱valve mechanism casing气缸体隔片cylinder spacer气缸盖密封环cylinder head ring gasket气缸盖垫片cylinder head gasket气缸套cylinder liner<cylinder sleeve> 干式缸套dry cylinder liner湿式缸套wet cylinder liner气缸水套water jacket膨胀塞expansion plug防冻塞freeze plug气缸壁cylinder wall环脊ring ridge排气口exhaust port中间隔板intermediate bottum导板guideway创成半径〔转子机〕generating radius缸体宽度〔转子机〕operating width机柱column燃烧室combustion chamber主燃烧室main combustion chamber 副燃烧室subsidiary combustion chamber预燃室prechamber涡流燃烧室`swirl combustion chamber分开式燃烧室divided combustion chamber涡流式燃烧室turbulence combustion chamber半球形燃烧室hemispherical combustion chamber 浴盆形燃烧室bathtub section combustion chamber L形燃烧室L-combustion chamber楔形燃烧室wedge-section combustion chamber 开式燃烧室open combustion chamber封闭喷射室closed spray chamber活塞顶内燃烧室piston chamber爆发室explosion chamber燃烧室容积比volume ratio of combustion cahmber燃烧室口径比surface-volume ratio of combustion chamber 通道面积比area ratio of combustion chamber passage 曲轴箱通气口crankcase breather凸轮轴轴承座camshaft bearing bush seat定时齿轮室罩camshaft drive<gear>cover曲轴箱检查孔盖crankcase door曲轴箱防爆门crankcase explosion proof door 主轴承盖main bearing cap气缸盖罩valve mechanism cover飞轮壳flywheel cover扫气储器scavenging air receiver活塞piston裙部开槽活塞split skirt pistonU形槽活塞U-slot piston滚花修复活塞knurled piston圆顶活塞dome head piston平顶活塞flat head piston凸顶活塞crown head piston<convex head piston> 凹顶活塞concave head piston阶梯顶活塞step-head piston筒形活塞trunk piston椭圆形活塞oval piston抗热变形活塞autothermic piston不变间隙活塞constant clearance piston镶因瓦钢片活塞invar strut piston直接冷却式活塞direct-cooled piston间接冷却式活塞indirect cooled piston 滑裙活塞slipper piston活塞速度piston speed活塞顶部piston head活塞裙部piston skirt整体活塞裙solid skirt活塞裙扩大衬簧piston skirt expander 滑履式活塞裙slipper skirt隔热槽heat dam活塞标记piston mark活塞销。
汽车专业英语
Chapter One — History of Automobile1.1 How Automobile Develops译前词语准备a car powered by steam以蒸汽为动力的汽车self-powered vehicle自身产生动力的汽车at an average speed平均时速gasoline engine汽油发动机auto conglomerate汽车集团a gas-powered quadricycle with no brakes一辆燃气动力、无制动装置的四轮车automaker汽车制造商Model T.“T”型车TextIn 1678, Ferdinand Verbiest built a working model of a car powered by steam. In 1769, Nicholas J. Cagnot built one of the first full-sized, self-powered vehicles that could travel about two miles per hour.By 1801 an English man, Richard Trevithica built another crude steam-powered carriage. By 1829 Sir G. Gurney built a steam engine that broke all distance records, it managed to make a 200-mile trip at an average speed of 15 miles per hour. The automobile is on its way!As engines grew more efficient and control devices improved, new power systems were tested. An early favorite was an electric automobile. It proved to be easy to start, and it was free of the sputtering noise.Electric cars soon lost their appeal because they could only travel about 50 miles before their batteries had to be recharged. This opened the door for the gasoline engine, however today electric cars may make a comeback.Detroit was a city of machine shops and skilled mechanics. It attracted many automakers like the Packard Motor Company from Ohio. Then David Buick, a local plumber, began turning out cars. The Dodge brothers built auto parts. By 1908 W.C. Durant from nearby Flint Michigan bought up several of the Detroit producers. The world first auto conglomerate, the General Motors Corporation, was launched.Detroit true pioneer was Henry Ford. In 1896 he built his first car, a gas-powered quadricycle with no brakes. Several improved models followed, each one represented by a letter of the alphabet. By 1907 Ford had reached T. He was determined to build a motor car that was affordable toeveryone. The Model T was just that. By 1914 more than half the cars in America were Model T.The demand for these Model T was so great that Henry Ford had to boost output. He began tinkering with the production process. By 1914, the world first automobile assembly line rolled into action. Other car makers quickly adopted assembly line production and the American car industry was revolutionized. Today there are many types of cars to choose from. There is the sporty coupe, the two-door sedan, the four-door sedan, hard top, convertible, station wagon, minivan, van, limousines and a wide variety of luxury cars.ExercisesTranslate following expressions into English（将下列词组译成英语）1. 蒸汽动力车2. 平均速度3. 电动汽车4. 汽油发动机5. 汽车装配线6. 四门轿车Translate following sentences into English（将下列句子译成英语）.1. 第一批汽车是在十九世纪晚期发展起来的。
汽车专业英语
Unit 12 Chassis Maintenance
底盘的维修
Section 1 Clutch Systems and Transmissions Troubleshooting
离合器与变速箱的检修
1 Clutch Maintaining and Adjusting
2 变速器养护 之道
如果你知道自
动变速器的各种 故障与引起故障 的原因之间的关 系，那么在寻找 故障原因时，你 就可以节省大量 的时间和精力。
大多数变速器
的故障是由于过 热造成的。在大 载荷下，如用拖 车载运、在雪地 上车子剧烈摇摆、 在炎热的天气下 连续刹车、赛车 等，变速器就会 过热。
At higher temperature the transmission fluid bums losing its lubricating qualifies and becomes oxidized leaving deposits all over inside the transmission ． Exposed to the heat the rubber seals and gaskets inside the transmission become hardened causing leaks．The metal parts warp and lose their strength．All this ， sooner or later ， results in transmission failure．
If you are able to relate various automatic transmission complaints to the condition that cause them，you can save a great deal of time and effort to find what is causing the trouble．
汽车专业英语全集
engine type) liquid cooled, in-line, 4cylinder, carb (发动机型号)水冷，直列，四缸，化油器式(engine) compression ratio (发动机)压缩比(engine) displacement (发动机)排量(engine) fuel (发动机)燃料3rd gear 三档齿轮3-way seat 三向座椅4WD control device 四轮驱动控制装置4WD indicator switch 四轮驱动指示灯开关4WD lamp electrical connection 四轮驱动指示灯接线4WD switch 四轮驱动开关5th synchromesh assy. 五档同步器总成6PK belt 6PK 多楔驱动皮带A / C compressor assembly 空调压缩机总成A / C control assembly 空调控制装置A/C & heater assy. 空调加热器总成A/C blower 空调鼓风机A/C clutch 空调压缩机离合器A/C compressor MTG bracket 空调压缩机安装支架A/C control assy. 空调控制器A/C housing assy. 空调箱总成A/C low pressure switch 空调低压开关A/C mode select switch 空调状态选择开关abdomen performance criterion 腹部性能指标Abdominal Peak Force 腹部力峰值ABS 防抱死制动系统acceleration fuel system 加速系统acceleration running noise level 加速行驶噪声accelerator interlocking type 加速踏板联锁式accounting foundation 财政基础Actual cycle work 实际循环功Actual torso angle 实际躯干角adapter 连接器additional features 附加装置additional rule 附加法规adjust screw 调整螺钉adjuster cable 调整拉线adjuster plug 调整盖adjuster screw assy. 调整螺栓总成adjuster washer 调整棘片adjuster, diff. bearing 差速器轴承调整螺母Adjustment system 调节装置Administration and Registration Division 管理科Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles, Equipment and Parts WhichCan Be Fitted and/or Be Used on Wheeled Vehicles and the Conditions for Reciprocal Recognition of Approvals Granted on the Basis of These Prescriptions关于对轮式车辆、安装和/或用于轮式车辆的装备和部件采用统一条件并相互认可基于上述条件批准的协定书Agreement Regulations 协定法规air cleaner 空气滤清器air cleaner assy. 空气滤清器总成air cleaner cartridge 空气滤清器滤芯Air compressor 空压机air condition compressor 空调压缩机air direct 空气走向air filter 空气滤清器air flow 空气流向Air flow meter 空气流量计air jet 空气量孔air metering hole 空气量孔air path 气道Air Pressure of Tire 轮胎气压Air type 空气型air valve 空气阀air-cooled 风冷Aisles 通道Alcohol 酒精all bearing 球轴承alternater bracket 发动机支架alternator 交流发电机alterntor assembly 交流发电机总成alumininum-rim 铝合金钢圈alumininum opposed model 铝制对开式AM/FM cassette stereo radio 调幅/调频立体声收放机ambulance 救护车Amended by 修正文amount of exhaust emission 排气排放量Amplitude resolution 幅度分辨率Analogue magnetic recorder 模拟式磁记录仪ANALYZER 分析仪anchor plate, brake caliper 制动钳安装支架Anchorage 座椅固定装置Angle of divergence 偏离角Angle of rotation 旋转角angles drift off vertical line 指针偏离垂直线的角度Angular diameter of the retro-reflecting device 回复反射装置的角直径annex 附件Announcement 公告anti, shutdown screw 防不灭车调整螺钉Antilock Brake System 防抱死制动系统appendix 附录Applicable motor vehicle 适用机动车Applicable scope 适用范围applicant 申请人application 申请application for notification 认可申请书approval 认可arm, valve rocket 摇臂armature 转子总成armature shaft 电枢轴Arm-rests 靠手Article 条Asphalt solution 沥青溶剂Attached document 附署文件attached sheet 附表Attached Table 附表attaching location of seat belt anchorage 座椅安全带固定装置的固定位置attachment 附属文件Attendants onboard 车上值班人员automatic chock cover setting 自动阻风门盖调到automotive electric system 汽车电系automotive engine system 引擎系统automatic transmission 自动变速器，自动排挡变速箱Auxiliary Brake 辅助制动器Auxiliary Direction Indicator Lamps 辅助转向信号灯auxiliary spring 副簧Auxiliary Stop Lamp 辅助驻车灯axle case 桥壳axle case assy. 桥壳总成axle ratio 桥速比axle weight 轴重back angle level 靠背角水平仪back angle quadrant 靠背角量角器back pan 靠板back spring 回位弹簧backing plate 制动底板Backing sheet 衬背板Back-Up Light 倒车灯backup washer 支撑挡圈bail wire 卡紧环balance tube 平衡管ball 钢球ball bearing 球轴承ball joint assy. , upper 上球销总成ball valve 球阀ball valve, inlet 进油口球阀bar 拉杆barrier 障碍壁battery 蓄电池battery terminal 蓄电池接线柱bearing cap 轴承盖bearing cover, input shaft 输入轴轴承盖bearing, connecting rod 连杆轴承bearing, input shaft 输入轴轴承Bed for babies 婴儿床bell 带束层bench seat 长条座椅berived cap 轴承盖bezel assy. 框板总成bezel, cluster 表框be pilot 小批量产品blead door 混合风门bleeder screw 放气螺钉blower assy. 鼓风机总成blower motor 鼓风发电机blower resistor 鼓风机电阻blower switch 鼓风机开关body 车身,阀体body & liftgate assembly 车身和举升门总成body assy. 车身总成body block 人体模块body of A/C & heater 空调加热器壳体bolt 主缸连接螺栓bolt, connecting rod 连杆螺栓Booster 助力器boot 护罩BOSCH starter motor assembly “波舍”起动机总成bottle assy. , coolant recover 冷却液回收罐总成bottom houseing, fuel pump 燃油泵下壳体bottom housing, fuel tank 燃油箱下壳体bracket 支架bracket assy. , spring seat 弹簧座支架bracket, steering damper mounting 转向减振器支架brake alarm lamp 制动报警灯brake alarm lamp switch 制动报警灯开关Brake booster 制动助力器brake caliper 制动钳brake caliper assy. 制动钳总成brake caliper piston 制动钳活塞brake combination valve 制动组合阀brake disc 制动盘Brake drum 制动鼓brake fluid 刹车油Brake hose 制动软管brake lining 刹车来令brake line, LF 左前制动油管字串6brake line, RF 右前制动油管brake oil flow 制动液流向brake paddle 制动踏板brake pedal 制动踏板Brake pipe 制动管brake shoes 刹车蹄片brake shoe 制动衬块Brake System 制动系Brake Systems for Tractors and Trailers 牵引车及挂车的制动装置Brake tester 制动器试验台brake valve 制动阀brake warning lamp 制动报警灯brake warning switch 制动报警开关Braking efficiency 制动效能braking force control system 制动控制装置Braking wheel 制动轮branch office 分署breaker 断电器bridge 过桥broadcasting vehicle 广播车brush 碳刷总成Buckle 带扣bulkhead 隔板Bulldozer 推土机bumper 保险杠Bumper element 保险杠构件bus transfer 车辆转移台bushing 衬套bushing, upper control arm 上控制臂衬套Business Place 业务场所bypass valve 旁通阀Cabinet Decision 内阁决议cable guide 拉线导向块cable-operated control system 液压式离合器系统Calibration factor of a data channel 数据通道校正系数calibration gas 标定气体calibration method 标定方法caliper assy. , front brake 前制动钳总成Camber 外倾camber angle 前轮外倾角camshaft 凸轮轴camshaft oil gallery 凸轮轴油道cap 加机油口盖cap assy. , power steering fluid reservoir 动力转向液油罐盖cap assy. , radiator 散热器盖总成cap screws 螺钉cap, connecting rod 连杆盖Capacity 容量,规格Capacity of the fuel tank 燃油箱容量capillary tube 毛细管carbon brushes & brush holder 电刷支架总成Carbon monoxide measuring instrument 一氧化碳分析仪Carburetor 化油器carburetor assy. 化油器总成carburetor bowl 化油器浮子室carburetor bowl vent system 化油器浮子室通风系统carburetor overhaul scheme 化油器分解图carburetor working scheme 化油器工作示意图carcase 胎体case runout (Max.) 差速器壳圆跳动（最大）Caster 后倾Catalyst 催化器category 类别cement and aggregate 水泥和混凝料Centreplane of occupant 乘员中心面Certified 经认证的Cetane number 十六烷值chain 驱动链chain drive 驱动链Channel amplitude class 幅度级通道Channel Frequency Class 频率级通道chassis 底盘chassis dynamometer 底盘测功机chassis shuttle 底盘平移台chassis number 底盘号Check and Maintenance 检查和保养check assy. , front door 前门限位器总成check assy. , rear door 后门限位器总成check ball 回止球check bracket 限位器支架check nut 限位器螺母check valve 单向阀check valve hole 回止阀孔check valve retainer 单向阀保持架check valve spring 单向阀弹簧check weight 回止块Chigi Circular No. 地技第…号Chigi No. 地技第…号Child Restraints 儿童约束装置chime module 蜂鸣器Chishin Circular No. 地审第…号Chishin No. 地审第…号chock heater 阻风门加热器总成chock plate 阻风门chock unloaded 阻风门连动装置choke 阻风门choke device 阻风装置choke unload mode 阻风门卸载状态cigarette lighter 点烟器circuit breaker, wiper/washer 刮水器/洗涤器电器断路器Circular 通告circular notice 通告clamp 卡圈Clamp ring type 锁紧圈式Cleaning efficiency 清洗效率Cleaning period 清洗周期clearance 最小离地间隙Clearance Lamp 示廓灯clinder head 气缸盖clip 卡子cluster housing 组合仪表壳Clutch system 离合器clutch assembly 离合器总成clutch control device 离合器控制装置clutch disc,clutch 离合器片clutch housing 离合器壳clutch master cylinder 离合器主缸clutch working cylinder 离合器工作缸Coating 涂层Code No. 型号Code of Federal Regulations 美国联邦法规总览Coefficient of luminous intensity (CIL) 亮度系数coil spring 圈状弹簧cold air 冷空气cold cranking voltage(min.) 最小冷启动电压collapsible spacer 可压缩隔垫collector 拼装台colorimeter 色度计coloured-light unit 有色灯光组column assy. 转向管柱总成combination brake switch and proporting 组合阀combined lamp 复合灯combined pump 复合泵combined pump diaphragm 复合泵膜片combined pump diaphragm rod 复合泵膜片杆combined pump lifter link 复合泵举升拉杆combined pump move direct 复合泵运动方向Combustion Chamber 燃烧室commutator 换向器compensate opening 补偿孔completion inspection certificate 终了检验证书Completion of notification 完成认可compressor 压缩机compression (both) 气环槽（两个）compression ignition type 压燃式Compression ratio 压缩比concrete mixer truck 混凝土搅拌车condenser 冷凝器condenser assy. 冷凝器总成conduit pipe 导管cone , diff. side bearing 差速器轴承，内圈带滚子cone, pinion front bearing 主动齿轮前轴承内圈带滚子cone, pinion rear bearing 主动齿轮后轴承内圈带滚子Confirmor 确认者connecting rod 连接杆connecting link 连接杆connecting rod journal diameter 连杆轴径connecting rod journal width 连杆轴径宽度connecting rod throttle 连杆喷油孔connector 连接器connector of service valve 维修阀接口Constant speed 等速construction and device 结构和装置control & tube assy. , hyd clutch 离合器工作缸和油管总成Control System 操纵系control valve 控制阀阀门control valve model 控制阀型式control valve seat 控制阀阀座convex plate 凸台cooling fan 冷却风扇cooling system 冷却系统Cornering Lamp 转弯灯corrected 修正的cotter 开口销counter 5th gear 中间轴五档齿轮counter shaft 中间轴coupled condition 连接状态Coupling Device 牵引装置cover 端盖cover & plate assy. 离合器盖及压盘总成cover assy. , air cleaner 空气滤清器盖总成cover, gear 侧盖cover, heater air 空气加热罩cover, rear axle case 后桥壳盖crane vehicle 起重车crankcase 曲轴箱crankshaft 曲轴crankshaft gear 曲轴齿轮crankshaft & connecting 曲轴连杆机构crankshaft oil gallery 曲轴油道crankshaft sprocket 轴承链轮critical flow 临界流Cross sensitivity of a linear transducer 线性传感器的横向灵敏度Crush distance 压碎距离Crush rate 压碎速率Crush Strength 压碎强度Cumulative time 累计时间cup 皮碗cup, diff. side bearing 差速器轴承外圈cup, pinion front bearing 主动齿轮前轴承外圈cup, pinion rear bearing 主动齿轮后轴承外圈Cut-off 明暗截止线cycle 冲程cyclinder head cover 气门室罩Cylinder 气缸cylinder block 汽缸体cylinder body 缸体Cylinder bore 缸径cylinder head 汽缸盖cylinder head cover 气门室罩cylinder number 气缸数cylinder working order(clockwise) 气缸工作顺序（顺时针）damper 转向减振器dangerous article 危险物darkroom 暗室Data channel 数据通道Data Processing 数据处理Date of notification 认可日期Deceleration of the structure 地板减速度Definitions 定义Definitions 术语deflection 偏移defroster 除霜器dehydrator 储液器和干燥器delay valve 延迟阀Design torso angle 设计躯干角designated 认定designated motor vehicle 经型式认定的机动车Designation 名称Designation of business place 业务场所名称Designation of Confirmor 指定确认者detonation 爆震device proper 装置本身Device type designation 装置的型式认定dextrorotation 右旋diameter 口径diaphragm 膜片diaphragm of fuel pump 油泵膜片diaphragm return spring 膜片回位弹簧diaphragm rod 膜片杆diaphragm spring 膜片弹簧Diesel fuel 柴油Diesel oil 轻柴油diesel smoke 柴油排烟Diesel smoke measuring instrument 柴油机排烟测量仪diesel-powered motor vehicle 柴油机动车differential case 差速器壳differential gear 半轴齿轮differential gearbox , front axle 前桥减速器differential gearbox , rear axle 后桥减速器differential side gear-to-case clearance 半轴齿轮与差速器壳之间的间隙Digital magnetic recorder 数字式磁记录仪Digitilizing 数字化Diluted exhaust gas 稀释排气dilution tunnel 取样探管direct injection type 直喷型direction indicator lamp 转向信号灯directly controlled wheel 直接控制车轮Director of the Vehicle and Component Approvals Division 车辆和零部件认证科长Director-General 署长Director-General of District Transport Bureau 地方运输局长Director-General of Land Transport Engineering Department 陆运管理处长Director-General of Local Land Transport Office 地方陆运署长Director-General of Motor Vehicle Inspection and Registration Office 机动车检验注册署长disc brakes 碟式刹车disc brake 盘式制动器disk assy. , clutch drived 从动盘总成disk type braker 盘式制动器Displacement 排气量Displacement system 位移装置Distillation properties 分馏特性distillation temperature 馏出温度distribution device 配气机构distributor 分电器distributor assy. 分电器总成distributor cap 分电器盖distributor rotor 分电器转子distributor shaft 分电器轴distributor type 分电器型号District Transport Bureau 地方陆运署documents to Be Submitted 需提交的文件dome lamp 顶灯door assy. , front RH. 右前门总成door assy. , rear RH. 右后门总成door hinge assy. 车门铰链总成door hinge plate 车门铰链垫板doors assembly & body accessories 前后车门总成及其附件double-lip seal 双唇油封double-tire 双胎dowel pin 定位销dowel pins-pump ring 定子定位销DRAWING PROCEDURE 绘制规程drier 干燥剂drier receiver 贮液干燥器drier receiver body 贮液气壳体drive end shield 前驱动端盖drive line system 传动系统drive pinion gear depth 驱动齿轮深度drive shaft 驱动轴drive sprocket 驱动链轮driver’s Seat驾驶员座椅driving beam 远光光束driving wheel 驱动轮drum brakes 鼓式刹车drum brake 鼓式制动器drum type braker 鼓式制动器dry air 干空气dry basis 干基dry-bulb 干球dummy 假人dump 自卸车dust boot 防尘罩Dynamic test 动态试验ECE Regulation ECE法规eddy-current type 电涡流式efe heater 进气加热器Effective height 有效高度Effective Weighted factor 有效加权系数Effective width 有效宽度Electrical 汽车电器Electrical System 电器系electromagnetic compatibility 电磁兼容性EMBOSSMENT 凸字Emergency Brake 紧急制动器Emergency Exit 紧急出口Emergency Motor Vehicles 应急用车Emergency Signals 应急信号用具Emergency Stop Indication Devices 紧急停车表示用具emergency valve 应急阀Emission Control Device 排放物控制装置end clearance 轴向间隙ENFORCEMENT PROCEDURE 实施规程Enforcement Regulation 实施规则engine 发动机，引擎Engine and Power Train System 发动机及动力传动系engine assy. 发动机总成engine displacement 发动机排量engine hood 发动机罩engine intake manifold 发动机进气歧管engine load 发动机负荷engine oil 发动机润滑油engine oil capacity 发动机机油容量engine outside diagram 发动机外形图engine revolution speed 发动机转速engine type 发动机型号Engineering and Safety Department 技术安全部entrance step 入口台阶entry item 填写项目entry value 填入值eqalizer 平衡架Equivalent inertia weight 当量惯性重量escort vehicle 护卫车European Economic Community Command 欧洲经济共同体指令Examination 审查examination affair 审查事务Exception to application 不适用条款excrement 排泄物exhaust 排水管exhaust duration 排气持续角exhaust emission 排气排放物Exhaust Emission Control Device 排放物控制装置exhaust hose 排放管exhaust manifold （发动机）排气歧管exhaust sytem 排气系统exhaust tube 放气管exhaust valve 排气门exhaust valve timing 排气门定时expander oil rail 油环衬簧expansion box 膨胀盒expansion core 蒸发器芯expansion valve body 阀体extension case 外接壳体EXTERNAL PROJECTION 外部突出物External surface 外表面External view 外观图extreme idle screw 极限怠速调整螺钉factory plate model 厂牌型号fan 风扇fan belt 风扇皮带fan & viscous drive 风扇及硅油离合器fast idle cam 快怠速凸轮fast idle cam link 快怠速凸轮连杆fast idle cam second step 快怠速凸轮第二阶段fast idle cam setting index 快怠速凸轮调整刻度fast idle mode 快怠速状态fast idle screw 快怠速调整螺钉fast idle speed 快怠速转速Federal Motor Vehicles Safety Standards 美国联邦机动车安全标准Feeling test 感觉试验Fiducial marks 基准标记Filament Lamp 白炽灯filler neck seal 加水口密封filler opening 进油口Filling-in Procedure 填写规程Filling-in Procedure for Each Item 每一项目的填写规程filter 滤清器，滤网Filter characteristics 滤波特性Filtering 滤波Fire Extinguisher 灭火器Fire truck 消防车fitting, flow control valve 流量控制阀接头fix shaft 定位轴flange 法兰flash point 闪点flasher, hazard lamp 危险报警闪光器Flexible Disk 软盘float 浮子float level 浮筒油面高度float pin 浮子轴floating coat 中涂floor damper 地板风门flow control valve 流量控制阀Fluid container 液体容器fluid torque converter 液力变扭器fluorescent surface 荧光面flying wheel 飞轮fog lamp 雾灯fog lamp relay 雾灯继电器fog lamp switch 雾灯开关Foil Thickness 箔厚folded seat 折叠椅folding seat 折叠式座椅foot angle quadrant 小腿夹角量角器fork 拨叉Formalin 福尔马林forward-opening inner door 内门前开型four-stroke cycle 四行程引擎four-wheel drive motor vehicle 四轮驱动的机动车Four-wheeled 四轮Frame 车架Frame and Body 车架及车身Friction clutch 摩擦离合器from evaporator drier 自蒸发器from heater core 出加热器from receiver drier 自贮液干燥器from water jacket intake manifold 自进气歧管水套front axle 前桥front axle assy. 前桥总成front axle motor 前桥挂档马达front bearing 前轴承front bearing retainer 前轴承盖front bearing, front output shaft 前输出轴前轴承front bearing, input shaft 输入轴前轴承front bearing, output shaft 输出轴前轴承front brake disc 前制动盘front brake disc assy. 前制动盘总成front case 前壳体front case of vacuum booster 助力器前壳体front coil spring 前螺旋弹簧front combined lamps 前组合灯front disk braker 前盘式制动器front edge 前边缘front end of shield 发电机前端盖front engine front drive F.F.式车辆front engine rear drive F.R.式车辆front fan 前风扇Front Fog Lamp 前雾灯front front axle 前前桥front opening 出油口front output shaft 前输出轴front output shaft gear 前输出轴齿轮Front overhang 前悬front panel 前板front pinion bearing 前主动齿轮轴承front port 前接口front propeller shaft 前传动轴front propeller shaft assy. 前传动轴总成front shock absorber 前减震器front stabilizer 前稳定杆front suspension 前悬吊front thrust plate 前配流盘front transfer 车辆转移台front tube failure 前管路失效状态front wall angle cover 前围角板front washer pump 前洗涤器泵front washer reservoir 前风挡洗涤器储液罐front wheel 前轮，前壳体front wheel alignment 前轮定位front wheel brake 前轮制动器Front Windshield 前风窗front wiper motor 前刮水器电动机Front-End Outline Marker Lamps 前端示廓灯Fuel 燃料fuel direct 燃油走向fuel filter 集滤器fuel filter housing 燃油滤清器壳体fuel filter paper 燃油滤清器滤纸fuel gauge 燃油表fuel gauge calibration 燃油表电阻Fuel Injection Device 燃料喷射装置fuel level indicator 机油压力表fuel pump 然油泵Fuel Resistance 耐油性fuel sensor 燃油（箱）传感器fuel sensor harness 燃油传感器线束fuel supply system 供油系Fuel System 燃料系Fuel System of Motor Vehicles Whose Fuel Is High-Pressure Gas 以高压气体作为燃料的机动车燃料系Fuel System of Motor Vehicles Whose Fuel Is Producer Gas 以发生炉煤气作为燃料的机动车燃料系Fuel Tank 燃料箱fule metering bar 计量杆full circle 大循环Full flow dilution 全流稀释full trailer 全挂车full-hydraulic type 全液力式full-trailer 全挂车fully-loaded 全负荷fuse 熔断器fuse panel 熔断器板garbage truck 垃圾车gas container 气体容器gas sample 样气gas turbine 燃气轮机gasket 节温器密封垫，衬垫gasket cylinder head cover 气门室罩垫gasket, intake manifold 进气歧管衬垫gasket, liftgate handle 举升门手柄垫片Gasoline 汽油gasoline fueled motor vehicle 汽油机动车gathering heat cover-TCV system TCV 系统集热罩gear , counter shaft fifth 五档中间齿轮gear end clearance, plastic gauge 齿轮端部间隙，塑料间隙规gear hub 齿毂gear range 档位级别Gear ratio 速比gear to body clearance(radial) 齿轮到壳体间隙（径向）gear, 4WD 四轮驱动齿轮gear, annulus 齿圈gear, low shift 抵挡齿轮gear, rear axle diff. 半轴齿轮gear, sleeve 齿套Gear-change lever 变速杆gears 档位General Comments 概述General Construction 通用结构GENERAL PROVISIONS 通用规则General provisions 一般规定generator 发电机Glazing 车窗glove box lamp 杂物箱灯Goods-Loading Accommodation 载货装置governor type 调节器式Gravimeter 重力计Gross Vehicle Weight 车辆总重ground Clearance 离地间隙Ground-Contact Section and Contact Pressure 接地部位及接地压力grouped lamp 组合灯grouped, combined or reciprocally incorporated lamps 组合、复合或混合灯光组halogen headlamp 卤素头灯halogen sealed-beam unit (HSB unit) 卤素封闭式(HSB)handle assy. , door I/S 车门内手柄总成handle assy. , door O/S 前门外手柄总成handle, liftgate lock 举升门锁芯手柄handle, window regulator 玻璃升降器手柄handling 处理办法HANDLING PROCEDURE 管理规程hanger 调耳harness 线束harness, body 车身线束harness, engine housing 发动机仓线束harness, lift gate 尾门线束hatch-back 掀背型Hazard Warning Lamps 危险报警闪光灯head 缸盖head form 头部模型head performance criterion 头部性能指标Head Restraint 头枕head room probe 头部空间探测杆Headlamp cleaner 前照灯清洗器headlamp dimmer switch 变光开关headlamp switch 前照灯开关Headlamps 前照灯Headlight tester 前照灯试验器Heat Resistance Test 耐热性试验heat-damage 热损害heated hydrogen flame ionization detector 加热式氢火焰离子化检测器heater 加热器heater & A/C panel lamp 暖风/空调开关灯heater, intake manifold 进气歧管加热器Heavy oil 重柴油hereinafter referred to as 下文称为Hereinafter the same 下文同hi-beem indicator lamp 组合仪表远光指示灯high idle speed 高怠速high pressure gas 高压气体high range 高档High-floor 高地板High-floor that can be opened in three ways 三向开启的高地板High-Pressure Gas Transport Devices 高压气体运输装置hip angle quadrant 臀部角度量角器hoist 举升hold in winding 保持线圈holddown pin 拉紧销钉holddown spring 压紧弹簧hole ladder type 带孔梯式honeycomb cell axes 蜂窝单元轴honeycomb ribbon axis 蜂窝条纹轴Horizontally-opposed 水平对置horn relay 喇叭继电器horn switch 喇叭按钮Horns 喇叭hose assy. , power steering return 动力转向回油管总成hose assy. , power to pump 油罐到泵的油管总成hose, coolant recover 冷却液回收管hose, radiator inlet 散热器进水软管hose, radiator to water pump 散热器至水泵软管hose, thermostat to intake minifold 节温器至进气歧管软管hot air 热空气hot idle mode 热怠速状态hot idle screw 热怠速调整螺钉housing 壳体，外壳字串5housing assy. 壳总成housing clutch 离合器壳housing end plug 壳体端盖housing, steering gear 转向器壳体H-point pivot H点支轴H-point sight button H点标记钮hub & bearing assy. 轮毂与轴承总成hub cap 车轮盖hub gear 齿毂hub range shift 换档毂hub sleeve No 2 二号毂套humidity correction factor 湿度修正系数hydraulic tappet 液力挺柱hydraulic type 液力式Hydrocarbon measuring instrument 碳氢化合物分析仪Hydrogen flame ionization detector 氢火焰离子化分析仪I/S locking rod 内锁止拉杆I/S release rod 内开启拉杆Identification Code 标记idle fuel tube 怠速油管idle fuel way 怠速油道idle jet 怠速喷口idle mixture screw 怠速混合气调整螺钉idle tube 怠速油管idling operation 怠速工况Idling Speed 怠速ignition coil 点火线圈ignition coil type 点火线圈类型ignition controler 点火控制器ignition key 点火钥匙ignition module 点火控制器ignition point 燃点ignition switch 点火开关Ignition System 点火系ignition wire 点火线Illuminating axis 光照轴illuminating surface 透光面Illumination angle 入射角Illumination intensity 光照强度Illumination of the retro-reflecting device 回复反射装置的照度illuminations actually measured 实测照度Illuminometer 照度计IMPACT REDUCTION OF INSIDE REARVIEW MIRRORS 缓冲式室内后视镜IMPACT REDUCTION TYPE OUTSIDE REARVIEW MIRRORS 缓冲式后视镜Impact test 冲击试验Impactor 碰撞块IMPORTED MOTOR VEHICLE 进口机动车in connection with 与…有关inclination angle 倾斜角indicating section 指示部分indicator lamp 指示灯indicator lamp, left turn 左转向指示灯indicator lamp, right turn 右转向指示灯indirectly controlled wheel 间接控制车轮Infant-carrying vehicles 幼儿专用车information 资料initial choke valve clearance 初始阻风门间隙initial inspection 初始检验Injection Nozzle 喷油嘴Injection Pump 喷油泵injector 喷油器inlet 进油口inlet hole 进气孔inlet hose 进风口inlet opening 进油口inlet tube 进油管inlet valve 进油阀Inner Dimension 内部尺寸inner shaft 内半轴inner tube 内胎input shaft 输入轴input shaft, tranmission 变速器输入轴input voltage 输入电压Inspection equipment 检验设备inspector 检验人员install panel 安装板instrument cluster 组合仪表（盘）instrument harness 仪表板线束instrument illumination lamps 组合仪表照明灯instrument panel assy. 仪表板总成instrument panels 仪表板intake and exhaust device 进排气装置intake duration 进气持续角intake heater 进气加热器intake manifold 进气歧管intake silencer 进气消声器intake valve 进气门intake valve timing 进气门定时integral place 整数integral power steering 整体式动力转向器integral type 整体式inter shaft assy. 动力转向中间轴总成Intercooler 增压中冷器intermediate axle shaft 中间半轴intermediate guide 中间导向器intermediate shaft 中间轴internal fan 内风扇interpolated value 内插值In-Use Motor Vehicles 在用车辆Issuance 发放ISSUANCE OF NOTICE 通知书的发放ist idle jet 第一怠速空气量孔Items 项JAIA 日本汽车进口商协会JAMA 日本汽车制造商协会Japan Automobile Importers' Association 日本汽车进口商协会Japan Automobile Manufacturers Association 日本汽车制造商协会Japan Automobile Standards Internationalization Center 日本汽车标准国际化中心Japanese Automobile Type Approval Handbook 日本车辆型式认证手册Japanese Industrial Standards 日本工业标准Jiko No. 自公第…号通告JIS 日本工业标准Jisei No. 自整第…号Jisha Circular 自车第…号通告Jiyu No. 自运第…号journal cross assy. 十字万向节总成jump, spark wire 高压电线katakana 片假名Kerosene 灯油key 键kick-type 反冲式Kinematic viscosity 运动粘度Kingpin 立轴kingpin caster angle 主销后倾角Kingpin inclination angle 主销内倾角kingpin sidewise inclination angle 主销内倾角knock 敲击knee angle quadrant 膝部角量角器Koshin No. 交审第xx号lamp switch, 4WD 四轮驱动灯开关lamp type 灯式Lap belt anchorages 腰带固定装置Large-Sized Rear Reflex Reflectors 大型后回复反射器Large-sized special 大型专用latch assy. , front RH. Door 右前门锁总成latch assy. , rear RH. Door 右后门总成lateral level 横向水平仪leading shoe 领蹄Leaf spring 片簧left fog lamp 左雾灯left headlamp 左前照灯left horn 左喇叭left steering 左转向left tail lamp 左尾灯legend 图例Length of trochoid 旋轮线Length, Width and Height 全长、全宽、全高Lens 配光镜lens, cluster 表蒙let in air 进气lever assy. , turn signal standard 综合开关操纵杆总成license lamp 牌照灯lift gate 举升门liftgate assy. 举升门总成liftgate latch assy. 举升门锁总成liftgate lock assy. 举升门锁芯总成light source module 光源模组Light Vehicles 轻型车辆Light-Exposure and Light-and-Water-Exposure Apparatus 光线暴露及光线与水暴露设备lighting device 照明装置Lighting System 照明系统Limit towards blue 趋蓝极限Limit towards red 趋红极限limiting valve body 限压阀壳体limiting valve spring 限压阀弹簧Linearity error 线性误差lining 衬片link assy. of front stabilizer 前稳定杆连杆总成linkage type 联杆式Liquefied Petroleum Gas-Fueled 燃用液化石油气机动车load cell simulator 载荷传感器模拟装置load sensing device 负载感受装置Loaded goods 装载物loaded WT 最大总质量Loading Capacity 载重量Loading platform 货箱Loading platform offset 货箱偏移量Local Land Transport Office 地方陆运署Local Office 地方署Location of business place 业务场所地点lock CYL assy. , RH. door 右车门锁芯总成lock piece, reverse gear 换档器锁片locking & indexing plate 锁止刻度盘Locking Device 锁止装置Locking system 锁止装置long axis 长轴long-body 长车身longitudinal center 纵向中心longitudinal centerline 纵向中心线longitudinal plane 纵向平面longitudinally-mounted 纵向安装low fuel warning indicator bezel 低燃油报警灯框low fuel warning indicator lens 低燃油报警灯透片low fuel warning module 低燃油报警组件low idle system 低怠速系统low range 抵挡low range lock plate 抵挡锁止板low speed jet 低速喷口lower control arm 下控制臂总成lower pressure switch 低压开关lubricant capacity 润滑油加注油lubricants 润滑油Lubricating oil 润滑油lubricating system 润滑系luminance factor 亮度因数luminous flux 光通量luminous intensity 光照强度M / CYL / vacuum booster assembly 制动主缸及真空助力器总成M/CYL push rod 主缸推杆Magnification 增大率main bearing 主轴承main bearing journal clearance 主轴承间隙main bearing journal diameter 主轴承轴径main bearing journal width 主轴承宽度main body, connector 化油器中体mainfold presure 歧管压力mainfold vacuum 歧管真空main fuel system & vacuum reriched system 主油系及真空加泷系统Main honeycomb block 主蜂窝块main injection jet 主喷口main jet 主量孔main oil gallery 主油道main spring 主簧Make and type 厂牌和型号Management supervisor 主管人manual transmission 手动变速器，手排挡变速箱Manufacturer 制造者MANUFACTURER TEST 制造者试验mapping 瞬态性能字串6mapping curve 瞬态性能曲线marker lamp, left front 左前示廓灯marker lamp, right front 右前示廓灯mass flow rate 质量流动速率master cylinder 制动主缸,总泵,刹车总泵master cylinder and vacuum booster 制动主缸及真空助力器master cylinder body 制动主缸缸体master cylinder cover 制动主缸缸盖mate 合笼max gas direct 混合器走向max. amps 最大电流MAX. power 最大功率Max. torque 最大扭距Maximum Loading Capacity 最大载重量maximum out-of round(all journals) 最大不圆度（所有轴径）maximum output 最大功率Maximum Stable Inclination Angle 最大稳定倾斜角maximum taper(all journals) 最大锥度（所有轴径）Maximum Torque 最大扭矩Measuring equipment 度量装备Measuring tape 卷尺mechanical steering 机械转向器median seating plane 座椅中心面medical treatment and epidemics prevention vehicle 医疗防疫车Meter 仪表metering rod 计量杆metering rod arm 计量杆摇臂metering rod arm assy. 计量杆摇臂总成metering valve 限流阀,限压阀micro-air direct 微量空气走向microphone 话筒Middle density foam rubber 中密度泡沫橡胶min. output voltage at 1000r/min 1000r/min 最小输出电压min. rpm 最小转速Minimum Ground Clearance 最小离地间隙Mini-sized 微型mini-sized motor vehicle 小型机动车。
汽车专业英语
汽车专业英语汽车专业英语Unit 1 Basic Structure of Automobile1.1 Structural Drawing and Terminology1.2 Basic Structure of Automotive1.3 The Vchicle Technical ParametersReading MaterialⅠHistory of the AutomobileReading Material ⅡThe Brief History of Electric VehicleT echnologyUnit 2 Engine Structure2.1 Structural Drawing and Terminology2.2 Classification of Engine2.3 Construction of Engine2.4 Engine Operating Principles2.5 Engine Starting System2.6 EFI System2.7 Cooling System2.8 Lubrication System2.9 Vehicle Emissions Contr01Reading MaterialⅠEight Possible Choices for Replacements ofEnginesReading Material ⅡThe New Diesel Technology and Its Training andRepairUnit 3 Chassis3.1 Structural Drawing and Terminology3.2 了he Drive Line3.3 Manual Transmission3.4 Automatic Transmissions3.5 Components of Suspension Systems3.6 Steering System3.7 Automobile Brake SystemReading MaterialⅠElectronic Brake Actuation SystemReading Materi alⅡSuspension Development 7ransverse SpringComposite Suspension ant Optimizing Unsprung Mass with wheel TravelUnit 4 Vehicle Body4.l Structural Drawing and Terminology4.2 Body4.3 Monocoque Construction Body4.4 Introduction to the Simple StructuralSurfaces（SSS）MethodReading MaterialⅠAerodynamics and Weight SavingReading MaterialⅡConcept Car DevelopmentUnit 5 Electrical and Electronic System5.1 Structural Drawing and Terminology5.2 Instrument Panel5.3 Electronic Devices5.4 CAN and L1N5.5 Antilock Brake System5.6 Air Bag System5.7 Lighting System5.8 Cruise Control System5.9 Air Conditioning SystemReading Material An Electronic Throttle Control and Its NoteworthyCapabilitiesUnit 6 New Energy of Automobile6.1 Structural Drawing and Terminology6.2 Alternative FueI Possibilities for Future6.3 Hybrid Vehicle Technologies6.4 The Electric Hybrid VehicleReading Material工正lcctric—gas01ine Engine Hybrid PowertrainSystem by 70yota Reading Material 11 wh。
汽车专业英语unit 4 Type of Automobile
Listening and Speaking
•
Fill in the blanks according to the text.
1. s_e_d_a_n 3. a_m_bul_a_nce 5. p_i_ck-_u_p
2. tr_a_ct_o_r 4. off-r_o_ad ve_h_icle 6. ti_p_ _p_ing vehicle
Relaxing
火车司机按喇叭, 按喇叭,按喇叭, 火车司机按喇叭,按喇叭, 交叉路口快到了, 交叉路口快到了, 交叉路口快到了,快到了。 火车上的人们晃得到处碰撞, 到处碰撞,到处碰撞, 火车上的人们晃得到处碰撞,到处碰撞 。
Words and expressions
vehicle [viːɪk(ə)l] n.
Listening and Speaking
•
Complete the word map according to the text.
小轿车
sedan
Types of Automobile
越野车
商务车
off-road vehicle commercial vehicle
Relaxing
The Train
Relaxing
the people on the train get bumped around,, bumped around bumped around, the people on the train get bumped around, bumped around,
火车 火车的轮子转呀转, 咔嗒咔嗒, 火车的轮子转呀转, 咔嗒咔嗒。 火车司机按喇叭,
4s store
sedan
passhicle
汽车专业英语
Accommodation 适应性Aerodynamics 空气动力学Air Conditioner 空调Air Drag 风阻Air Suspension 空气悬挂Analysis 分析Anti Corrosion 防腐Anti Rust 防锈Ashtray 烟灰盒Assembly 装配Assistant’s seat 副驾驶座Attaching Parts 附件Azimuth 方位（角）（极坐标）Back Angle 靠背角Backrest 靠背Backup Lamp 倒车灯Binocular Obstruction 双眼盲区BIW (Body-In-White) 白车身Blower 风机Body 车身，车体Bolt 螺栓Bonneted Cab 凸头驾驶室Bracket 托架Breakdown 分块Bumper 保险杠Bushing 衬套Case 壳体Caution Plate 警告牌Centroid 重心Cigarette Lighter 点烟器Chassis 底盘Chassis Frame 车架Check Arm 限位器Clip 卡扣Cluster Meter 组合仪表盘Coat Hanger 衣帽架Coat Hook 衣帽钩Collar 套环Combination Switch 组合开关Comfort 舒适性Component 总成Concealed Wipers 隐藏式雨刮器Condenser 冷凝器Contour 轮廓线Controls 控制件Convex Mirror 凸面镜Coolant 冷却液Cooler 制冷器Crash 碰撞Cup Holder 水杯架Curtain 窗帘Curtain Rail 窗帘滑轨Curvilineal 曲线的Dash Board 前围内板Delivery of the Drawing 出图Displacement 位移Door Check 限位器Door Header Rail 车门顶轨Door Lock 车门锁Door Opening 门洞Door Outer Handle 车门外手柄Door Outer Panel 车门外板Door Panel 门护板Door Pocket 门袋Door Regulator 车门玻璃升降器Door Sash 车门窗框Door Striker 锁环Door Trim 车门护板Door Ventilator 三角窗Drip Rail 滴水凹槽顶轨Drive Configuration 驱动形式Dummy Plate 平衡板Dynamic 动态的Ellipsoid Surface 椭球面Emblem 商标Engine 发动机Engineering 工程Entrance Handrail 上车门扶手Entry & Exit 进出Ergonomics 人机工程学Eyellipse 眼椭圆Fatigue Analysis 疲劳分析FEM (Finite Element Method) 有限元Fender 翼子板Fender Protector 挡泥护板Fender Stay 挡泥撑条Fender Welt 挡泥衬板Field of View 视野Finish Washer 精加工垫圈Fire Fighting Truck 消防车Fixed 固定的Flange Bolt 凸缘螺栓Fleece 绒毛织物Floor Insulator 地板隔热层Fluid Reservoir 贮液罐Fog Lamp 雾灯Fore/aft 前后Forward Control 平头Frame 车架Front Overhang 前悬Front Panel 前挡板，前围外板Front Turn Signal Lamp 前转向灯Fuse & Relay Box 保险丝和继电器箱Garnish 装饰板Gauge 量表Glare-free 防眩目Glass Run Channel 玻璃滑槽Glazing Rubber Plate 镶玻璃用橡胶板Glove Box 杂物盒Gradeability 爬坡度Grille 格栅Grip 扶手Grommet 密封圈Ground Clearance 离地间隙Halogen Headlamp 卤素大灯Handle Cover 手柄罩Head Contour 头廓包络线Head Restraints 头枕Headlamp 前大灯Headliner 顶棚Headlining 顶棚内饰Headrest 头枕Heater 加热器Heater Plumbing 取暖装置管路Height Adjuster 高度调节器High-mount 高位Hinge 铰链Hinge Bracket 铰链托架Holder 支架Hood 发动机罩Hook 挂钩Hose 软管Impact 碰撞In-line 直列Ingress/egress 进出Inside Lock Knob 内锁止按钮Instrument Panel 仪表板Interior Trim 内饰Intermittent Wiper 间歇式刮水器Joint 接头Joint Duct 连接管道Kinematics 运动学Lateral 横向Lever 杆籁绅士Plate 牌照籁绅士Plate Bracket 牌号托架籁绅士Plate Lamp 车牌灯Lift-up Type 翻转式（前围外板）Linear 线性的Load 载荷Lock Cylinder & Key 锁芯和钥匙Longitudinal 长度方向的Loose Panel 可卸盖板Lower Apron 下挡板Lumbar Support 腰托Luxury Interior Level 豪华内饰Mud Guard 挡泥板Mud Shield 挡泥板（侧）Male-to-Female Ration 男女比例Manikin 人体模型Manoeuvrable 操纵灵活的Meeting Minutes 会议纪要Member 横梁Meter & Gauge 仪表盘Meter Cable 仪表电缆Meter Cluster 仪表束Meter Cover 仪表面罩Meter Face 仪表面Meter Hood 仪表罩Milling 铣Mirror Holder 后视镜支架Model 模型Moquette 绒面Mount 悬置Movable Part 运动件Mudguard 挡泥板Muffler 排气消声器Muscular Contour 强壮的外形（造型风格）））Non-linear 非线性的Nozzle 喷嘴Nut 螺母Operation Hardware 开闭、锁紧装置Optimization 优化Ornament 标识Outlet 出风口Overhead Console Box 高架箱Packing 衬垫Parking Brake Lever 驻车制动手柄Percentile 百分位Perimeter 周长、周边Pillar 立柱Pin 销Pivot Point 关节点Plain Washer 平垫圈Plan View 俯视图Plate & Label 名牌和标识Plate Nut 板螺母Pneumatic Spring 空气弹簧Pocket 凹槽Pocket Facing 凹槽镶面Power Steering 动力转向Presentation 展示Push Button 按钮Push-on Spring Nut 顶推弹簧螺母Quarter Panel 后顶盖侧板Quarter Window 侧车窗Radiator 散热器Raised Roof 高顶Rear Overhang 后悬Rear View Mirror 后视镜Rear Wall 后围Reclining 倾斜Reflector 反射板Regulation 法规Reinforcement 加强件Rendering 效果图Requirement 要求Resin 树脂Retainer 护圈Rigidity 刚度Rivet 铆钉Roof Console 高架箱Roof Hatch 天窗Roof Panel 车顶板Room Lamp 室内灯Root-Mean-Square 均方根Round Oval Instrumentation 环抱式仪表板Safety 安全性Screw 螺钉Screw Grommet 密封圈螺钉Scuff 压条（门槛处）Seat Bench 长排座Seat Support 座椅支架Seat Track 座椅导轨Self-Supporting 自承载式Service Parts 修理配件Set Screw 定位螺钉Shim 调整垫片Shin-Knee Contour 膝部包络线Shock Absorber 减振器Side View 侧视图Sight Line 视线Silencer 消声器Sill 横梁Simulation 模拟Sketch 草效果图Sleeper 卧铺Sleeping Bed 卧铺Sleeping Berth 卧铺Slide Adjuster 前后滑动调节器Snap Ring 开口环Snorkel 进气管Snowplow 除雪车Spacer 隔环Speedometer 车速仪Splash Apron 侧挡泥板Spot Welding 点焊Static 静态的Steering Column 转向柱Steering Column Adjuster 转向柱调整器Steering Gear 转向机构Steering Wheel 方向盘Step Plate 踏脚板Step Protector 脚踏板护板Stiffener 加强肋Stiffness 刚度Stop Lamp 制动灯Stopper 挡块Strain 应变Strength 强度Stress 应力Structure 结构Styling 造型Sun Visor 遮阳板Surfacing 线图Suspension 悬架Switch 开关Tachograph & Speedometer 自记式转速记和车速表Tachometer 发动机转速表Tail Lamp 尾灯Tapping Screw 自攻螺钉Template 模板Ticket/Card Holder 名片夹Tilt 翻转（驾驶室）Tipper 自卸车Tonnage 吨位Torsional Stiffness 扭转刚度Tread 轮距Trim 饰件Trim Panel 装饰板Turning Radius 转弯半径Upper Console 高架箱Variant 变形车Ventilation 通风Vertical 垂直方向的Vinyl 乙烯基Washer 垫圈Water Proof Film 防水层Weather Strip 密封条Wear-Resistant 防磨Windscreen 风窗Windshield 风窗Windshield Washer 挡风玻璃洗涤器Windshield Wiper 挡风玻璃刮水器Wiper 刮水器Wiper Arm 刮臂Wiper Blade 刮片Wiper Link Assembly 刮水器连杆组件Wiring Harness 线束07轮椅升降机Wheel chair lift图例legend工位station吊运装置overhead hoist更衣室restroom1号厂房工艺布置方案图proposal of the Plant I layout合笼mate底盘平移台chassis shuttle车辆转移台bus transfer前围角板front wall angle cover后围侧板rear wall side cover保险杠bumper三类底盘three type chassis左侧围应力蒙皮R/S stretching skin (road side)中涂floating coat拼装台collector切割轮口wheel -arch cutting内饰trim线束harness返工re-doing轮罩护板wheel house发车前准备pre-delivery举升hoist小批量产品be pilot2 套two kits配电站power transformer substation裙板skirt发动机托架engine holding frame诊断报警系统diagnosis and alarming system互换性interchangeability缩微图纸microfiche files总装final assembly磷化phosphating仪表板dash board切齐trimming结构完整性structure integrity自动愈合的防腐材料self-healing corrosion preventative material 长途客车inter-city bus改装厂refitting factory遮阳板sun visor随车工具tool box钢化玻璃toughened grass异形钢管special steel pipe全天候空调系统full range A/C强制通风ram-air ventilation停机时间downtime无公害柴油clean diesel宽敞悬臂式座椅roomy cantilevered seat防滑地板no-skid floor织物纹里铝合金textured aluminum extrution 爬坡能力grade ability排水阀drain valve除湿器moisture ejector怠速时at idle琴式驱动桥banjo type drive axle通风口duct恒温控制thermostatic control平衡水箱surge tank变光开关simmer switch消音器muffler防破坏vandal resistant聚碳化透镜poly-carbonate len镀锌板galvanized plate搭接lap亮丽的外表smart apperance隐藏式固定concealed fastening水洼ponding发动机中置式客车bus with under floor engine 组合式客车车身modular bus body薄壳式结构shell construction衬垫pad空气导流板air deflector搁梁shelf beam腰梁waist rail梭梁stabilizing beam腰带式安全带diagonal safety belt压条trim strip嵌条insertion strip翼板fender斜撑bracing piece转向盘回正性试验test of steering wheel returnability转向盘转角脉冲试验steering wheel impulse input test转向盘转角阶跃输入试验steering wheel step input or transient state yaw response test极限侧向加速度试验limiting lateral acceleration test汽车平顺性随机输入行驶试验automobile ride random input running test汽车平顺性单脉冲输入行驶试验automobile ride single pulse input running test汽车悬挂系统固有频率与阻尼比的测定试验measurement of natural frequency and damping raito of suspension 功率突然变化影响试验test of effect of sudden power change收油门后控制试验test of control at breakway横风稳定性试验test of crosswind stability反冲试验kick-back test轮胎爆破响应时间试验test of burst response of tyre绕过障碍物试验obstacle avoidance test移线试验lane change testJ型转弯试验test of J turn频率响应时间试验frequency response test瞬态响应时间试验transient response test阶路响应时间试验step response test脉冲响应试验pulse response test静态操舵力试验static steering effort test悬架举升试验jack-up test of suspension耐翻倾试验test of overturning immunity轮辋错动试验rim slip test风洞试验wind tunnel test制动稳定性试验test of braking stability最小转弯直径试验minimum turning diameter test操舵力试验steering effort test汽车发动机类型type发动机engine内燃机intenal combusiton engine动力机装置power unit汽油机gasoline engine汽油喷射式汽油机gasoline-injection engine火花点火式发动机spark ignition engine压燃式发动机compression ignition engine往复式内燃机reciprocating internal combustion engine 化油器式发动机carburetor engine柴油机diesel engine转子发动机rotary engine旋轮线转子发动机rotary trochoidal engine二冲程发动机two-stroke engine四冲程发动机four-stroke engine直接喷射式柴油机direct injection engine间接喷射式柴油机indirect injection engine增压式发动机supercharged engine风冷式发动机air-cooled engine油冷式发动机oil-cooled engine水冷式发动机water-cooled engine自然进气式发动机naturally aspirated engine煤气机gas engine液化石油气发动机liquified petroleum gas engine 柴油煤气机diesel gas engine多种燃料发动机multifuel engine石油发动机hydrocarbon engine双燃料发动机duel fuel engine热球式发动机hot bulb engine多气缸发动机multiple cylinder engine对置活塞发动机opposed piston engine对置气缸式发动机opposed-cylinder engine十字头型发动机cross head engine直列式发动机in-line engine星型发动机radial engine筒状活塞发动机trunk-piston engine斯特林发动机stirling engine套阀式发动机knight engine气孔扫气式发动机port-scavenged engine倾斜式发动机slant engine前置式发动机front-engine后置式发动机rear-engine中置式发动机central engine左侧发动机left-hand engine右侧发动机right-hand engine短冲程发动机oversquare engine长冲程发动机undersquare engine等径程发动机square engine顶置凸轮轴发动机overhead camshaft engine双顶置凸轮轴发动机dual overhead camshaft engine V形发动机V-engine顶置气门发动机valve in-head engine侧置气门发动机side valve engine无气门发动机valveless engine多气门发动机multi-valve engine卧式发动机horizontal engine斜置式发动机inclined engine立式发动机vertical engineW形发动机I形发动机I-engineL形发动机L-engineF形发动机F-engine性能performance二冲程循环two-stroke cycle四冲程循环four-stroke cycle狄塞尔循环diesel cycle奥托循环otto cycle混合循环mixed cycle定容循环constant volume cycle 工作循环working cycle等压循环constant pressure cycle 理想循环ideal cycle热力循环thermodynamic cycle 冲程stroke活塞行程piston stroke长行程long stroke上行程up stroke下行程down stroke进气行程intake stroke充气行程charging strokecompression stroke爆炸行程explosion stroke膨胀行程expansion stroke动力行程power stroke排气行程exhaust stroke膨胀换气行程expansion-exchange stroke换气压缩行程exchange-compression stroke止点dead center上止点top dead center(upper dead center)下止点lower dead center(bottom dead center) 上止点前budc(before upper dead center)上止点后atdc(after top dead cetner)下止点前bbdc(before bottom dead center)下止点后abdc(after bottom dead center)缸径cylinder bore缸径与行程bore and stroke空气室energy chamber气缸余隙容积cylinder clearance volume燃烧室容积combustion chamber volume气缸最大容积maximum cylinder volume压缩室compression chamber排气量displacement发动机排量engine displacement活塞排量piston swept volume气缸容量cylinder capacity单室容量single-chamber capacity容积法volumetry压缩比compression ratio临界压缩比critical compression ratio膨胀比expansion ratio面容比surface to volume ratio行程缸径比stroke-bore ratio混合比mixture ratio压缩压力compression pressure制动平均有效压力brake mean effective pressure(bmep) 空燃比air fuel ratio燃空比fuel air ratio燃料当量比fuel equivalence ratio扭矩torque单缸功率power per cylinder升功率power per liter升扭矩torque per liter升质量mass per liter减额功率derating power输出马力shaft horsepower马力小时，马力时horsepower-hour总马力gross horse power总功率gross power净功率net power燃油消耗量fuel consumption比燃料消耗率specific fuel consumption 空气消耗率air consumption机油消耗量oil consumption有效马力net horse power额定马力rated horse power马力重量系数horsepower-weight factor 制动功率brake horse power制动热效率brake thermal efficiency总效率overall efficiency排烟极限功率smoke limiting horsepower 功率曲线power curve机械损失mechanical loss机械效率mechanical efficiency有效热效率effective thermal efficiency 充气系数volumetric efficiency过量空气系数coefficient of excess air适应性系数adaptive coefficient扭矩适应性系数coefficient of torque adaptibility转速适应性系数speed adaptive coefficient强化系数coefficient of intensification校正系数correction factor换算系数conversion factor活塞平均速度mean piston speed发动机转速engine speed (rotational frequency) 怠速转速idling speed经济转速economic speed起动转速starting speed最低稳定工作转速lowest continuous speed with load 最大扭矩转速speed at maximum torque最高空转转速maximum no load governed speed 调速speed governing超速overspeed怠速idling转速波动率speed fluctuation rate工况working condition(operating mode) 额定工况declared working condition变工况variable working condition 稳定工况steady working condition 空载no-load全负荷full load超负荷overload部分负荷part load充量（进气）charge旋转方向direction of rotation顺时针clockwise逆时针counter-clockwise左转left-hand rotation右转right-hand rotation外径major diameter中径pitch diameter内径minor diameter径向间隙radial clearance发动机性能engine performance加载性能loading performance起动性能starting performance加速性能acceleration performance 动力性能power performance排放性能emission performance空转特性no load characteristics负荷特性part throttle characteristics调速特性governor control characteristics万有特性mapping characteristics稳定调速率steady state speed governing rate气缸体和气缸盖cylinder block and head气缸体cylinder block整体铸造cast inblock (cast enblock)发动机罩engine bonnet气缸体加强筋engine block stiffening rib气缸cylinder（转子机）缸体stator07 reock frameadhanism casingacer环ad ring gasketad gasketer(cylinder sleeve)r linerer lineretplugallrtte bottum转子机）radius转子机）widthn chamberustion chamber combustion chamberrustion chamber室mbustion chamber室combustion chamber室cal combustion chamberction combustion chamberon chambertion combustion chamberustion chamberay chamber烧室mberhamber比io of combustion cahmber比ume ratio of combustion chamberof combustion chamber passage 口breather座earing bush seat罩rive(gear)cover孔盖door门explosion proof doorng caphanism coververair receiver塞iston塞tonpistonistond piston(convex head piston) ead pistonpistonn塞c piston塞earance piston活塞piston活塞ed piston活塞oled pistononedd衬簧expander裙tkbossbushing销g piston pin销g piston pin活塞销piston pin环piston ringpiston ringiston ringngne ringr ringringcontrol ring载双坡口油环loaded slotted oil control ring elled oil control ringvel topvel bottom环ge oil control ring ngted piston ringexpandergrooveland面g构rod杆机构ated connecting rod 杆机构ecting rod杆机构necting rodrodrod small endg rod big endrod shankecting rodade connecting rod ecting rode connecting rod connecting rod rod caprod bearingcrankshaftcrankshaftcrankshaftrankshaft曲轴ankshaftfront endmain journalal overlapng承thrust bearing earing shelloil passageeuseelalancereightvibration damperanceralanceralancersprocketalhaft通风装置nkcase ventilating system ng gearindle矩oment of inertiaarksystemshaft length性力ng inertia force,1st order 性力ng inertia force, 2nd order inertia force轴camshaft轴camshaft机构rive轴haftearing journalearing轮ccentricprocket齿轮ming gearear wheel）：swm45100 FanE『翻译中国』2004-5-27 14:07:30 te gear(counter gear)aft gearaft轴on imput shaft轴on output shaft齿轮轴on drive gear shafton main shaft轴on countershaft刚度shaft（变速比）on gear ratiorepressure力odulator pressureressureor or trimmer pressurere(input pump )置充油压力mic unit change pressure(output pump )il pumpegulator vavle阀gulator valve旁通阀bypass valvealvelvee生器n generatortor(shift torwer)veve控制阀ntrol valve锁止ockup换档系统utomatic control system 换档系统-hydraulic automatiec换档shfititshfithiftiftte shiftresisulepower shift程automatic shift automatic shft lementergear shift lever) ）变速杆ctork (gear shift fork)杆ar shift forkpedal叉道轨）ge(direct control)速ft (handle change)ontrole07空档位置neutral position直接驱动direct drive高速档top gear(high gear)低速档bottom gear(low speed gear)第一档first gear第二档second gear超速档overdirve gear经济档economic gear倒档reverse gear爬行档creeper gear驱动特性drive performance反拖特性coast performance定输入扭矩特性constant input torque performance全油门特性full throttle performance寄生损失特性no load (parasitic losses)performance 原始特性primary characteristic响应特性response characteristic吸收特性absorption characteristic全特性total external characteristic输入特性characteristic of enhance输出特性characteristic of exit力矩特性torque factor(coefficient of moment) 过载系数overloading ratio变矩系数torque ratio能容系数capacity factorr几何相似geometry similarity运动相似kinematic similarity动力相似dynamic similarity透穿性transparency万向节和传动轴universal joint and drive shaft万向节universal joint非等速万向节nonconstant velocity universal joint 等速万向节constant velocity universal joint准等速万向节near constant velocity universal joint 自承式万向节self-supporting universal joint非自承式万各节non self suporting universal joint 回转直径swing diameter等速平面constant velocity plane万向节夹角true joint angle十字轴式万向节cardan (hookes)universal joint 万向节叉yoke突缘叉flange york滑动叉slip yoke滑动节，伸缩节slip joint花键轴叉slip shaft yoke轴管叉（焊接叉）tube(weld yoke)十字轴cross(spider)十字轴总成cross assembly挠性元件总成flexible universal joint球销式万向节flexible member assembly双柱槽壳housing球环ball球头轴ball head球头钉button中心球和座centering ball and seat球笼式万向节rzeppa universal joint钟形壳outer race星型套inner race保持架cage可轴向移动的球笼式万向节plunging constant velocity joint筒形壳cylinder outer race柱形滚道星形套inner race withcylinder ball grooves 偏心保持架non-concentric cage滚动花键球笼式万向节ball spline rzeppa universal joint外壳outer housing内壳体inner housing球叉式万向节weiss universal joint球叉ball yoke定心钢球centering ball三球销万向节tripod universal joint三柱槽壳housing三销架spider双联万向节double cardan universal joint凸块式万向节tracta universal joint凸块叉fork yoke榫槽凸块tongue and groove couplijng凹槽凸块groove coupling传动轴drive shaft(propeller shaft)传动轴系drive line传动轴形式drive shaft type两万向节滑动的传动轴two -joint inboard slip ddiveshaft 两万向节外侧滑动传动轴two joint ouboard slip drive shaft 单万向节传动轴single joint coupling shaft组合式传动轴unitized drive shaft传动轴减振器drive shaft absorber传动轴中间轴承drive shaft center bearing传动轴管焊接合件weld drive shaft tube assembly传动轴特征长度drive shaft length传动轴谐振噪声resonant noise of rive shaft传动轴的临界转速critical speed of drive shaft传动轴总成的平衡balance of drive shaft assembly允许滑动量slip相位角phase angle传动轴安全圈drive shaft safety strap驱动桥drive axle(driving axle)类型type断开式驱动桥divided axle非独立悬架式驱动桥rigid dirve axle独立悬架式驱动桥independent suspension drive axlesteering drive axle贯通式驱动桥tandem axles“三速”贯通轴"three-speed" tandem axles单驱动桥single drive axle多桥驱动multiaxle drive减速器reducer主减速器final drive单级主减速器single reduction final drive双级主减速器double reduction final drive前置式双级主减速器front mounted double reduction final drive后置式双级主减速器rear mounted double reduction final drive上置式双级主减速器top mounted double reducton final drive行星齿轮式双级主减速器planetary double reduction final drive贯通式主减速器thru-drive双速主减速器two speed final drive行星齿轮式双速主减速器two speed planetary final drive双级双速主减速器two speed double reduction final drive轮边减速器wheel reductor(hub reductro)行星圆柱齿轮式轮边减速器planetary wheel reductor行星锥齿轮式轮边减速器differential geared wheel reductor(bevelepicyclick hub reductor) 外啮合圆柱齿轮式轮边减速器spur geared wheel reductor差速器锥齿轮式差速器bevel gear differential圆柱齿轮式差速器spur gear differential防滑式差速器limited -slip differential磨擦片式自锁差速器multi-disc self -locking differential凸轮滑滑块自锁差速器self-locking differential with side ring and radial cam plate 自动离合式自锁差速器automotive positive locking differential强制锁止式差速器locking differential液压差速器hydraulic differential轴间差速器interaxial differential差速器壳differential carrieer(case)主降速齿轮final reduction gear驱动轴减速比axle ratio总减速比total reduction ratio主降速齿轮减速比final reduction gear ratio双减速齿轮double reduction gear差速器主齿轮轴differential pinion-shaft差速器侧齿轮differential side gear行星齿轮spider gear(planetary pinion)螺旋锥齿轮spiral bevel gear双曲面齿轮hypoid gear格里林齿制gleason tooth奥林康型齿制oerlikon tooth锥齿轮齿数number of teeth in bevel gears and hypoid gears锥齿轮齿宽face width of tooth in bevel gears and hypoid gears 平面锥齿轮plane bevel gear奥克托齿形octoid form平顶锥齿轮contrate gear齿面接触区circular tooth contact齿侧间隙backlash in circular tooth差速器十字轴differential spider差速器锁止机构differential locking -device差速器锁止系数differential locking factor差速器壳轴承carrier bearing桥壳axle housing整体式桥壳banjo housing可分式桥壳trumpet-type axle housing组合式桥壳unitized carrier-type axle housing对分式桥壳split housing冲压焊接桥壳press-welding axle housing钢管扩张桥壳expanded tube axle housing锻压焊接桥壳forge welding axle housing整体铸造式桥壳cast rigid axle housing半轴axle shaft全浮式半轴full-floating axle shaft半浮式半轴semi-floating axle shaft四分之三浮式半轴three-quarter floating axle shaft 驱动桥最大附着扭矩slip torque驱动桥额定桥荷能力rating axle capactiy驱动桥减速比driveaxle ratio驱动桥质量drive axle mass单铰接式摆动轴single-joint swing axle双铰接式摆动轴double joint swig axle悬架系suspension system悬架suspension类型type非独立悬架rigid axle suspension独立悬架independent suspension平衡悬架equalizing type of suspension组合式悬架combination suspension可变刚度悬架。
汽车专业英语
专业英语一automobile 汽车（美）assembly line 装配线petroleum refining石油提炼body and frame 车身与车架engine发动机、引擎drive line 传动系统running gear 控制装置suspension 悬架系统unitized body 承载式车身gasoline engine 汽油机diesel engine 柴油机gas turbine 燃气轮机battery 电池（组）fuel cell 燃料电池hybrid power混合动力系统piston 活塞rotary engine 转子发动机vehicle 车辆transmission 变速器drive shaft 传动轴differential 差速器rear axle 后轴rear-wheel drive 后轮驱动front-wheel drive 前轮驱动braking system 制动系统wheel 车轮tire 轮胎steering system 转向系统spring 弹簧shock absorber 减震器Macpherson strut 麦弗逊式悬架torsion bar 扭力杆strut rod 支撑杆stabilizer bar 横向稳定杆二internal combustionengine 内燃机external combustionengine 外燃机fuel 燃料steam engine 蒸汽机intermittentcombustion engine 间隔燃烧式发动机continuous combustionengine 连续燃烧式发动机turbine engine 涡轮发动机rocket engine 火箭发动机jet engine 火箭发动机Wankel engine 汪克尔发动机、转子发动机stroke 行程cooling system 冷却系统fuel system 燃料系统ignition system 点火系统spark-ignition engine 火花点燃式发动机compression-ignitionengine 压燃式发动机liquid-cooled 水冷式（液体冷却）air-cooled 风冷式（空气冷却）三cylinder block 缸体cylinder 气缸connecting rod 连杆crankshaft 曲轴cylinder head 气缸盖combustion chamber燃烧室valve 气门、阀camshaft 凸轮轴flywheel 飞轮intake manifold 进气歧管exhaust manifold 排气歧管carburetor 化油器fuel injector 燃料喷射器cast iron 铸铁aluminum 铝cooling fluid 冷却液spark plug 火花塞intake valve 排气门cam 凸轮gear 齿轮belt 皮带chain 链条overhead camshaft（OHC）上置式凸轮轴rpm=revolutions perminute 转速、转数每分钟horsepower 马力intake system 进气系统sensor 传感器oxygen sensor 氧传感器fuel induction燃料吸入系统四fuel tank 油箱fuel line 燃料管路fuel pump 燃料泵fuel filter燃料滤清器power train controlmodule（PCM）动力系统控制模块fuel injection system 燃料喷射系统distributor 分电器ignition coil 点火线圈ignition wire 点火线路charging system 充电系统ignition switch 点火开关solenoid 电磁线圈starter motor 起动电机alternator 交流发电机voltage regulator 稳压器lubrication system润滑系统oil pump 机油泵oil filter 机油滤清器oil cooler 机油冷却器antifreeze 防冻液coolant pump 冷却液泵thermostat 节温器radiator 散热器、水箱clutch 离合器radiator overflow tank 散热器溢流箱、膨胀水箱air intake ducting 进气管air filter 空气滤清器manifold air pressure sensor 进气歧管压力传感器turbocharger 涡轮增压器muffler 消声器、消音器catalytic converter 催化转化器exhaust pipe 排气管pollution control system 排放控制系统carbon monoxide 一氧化碳nitrogen oxide 氮氧化物hydrocarbons 碳氢化合物carbon canister 碳罐exhaust gas recirculator （EGR）废气再循环positive crankcase ventilation强制曲轴箱通风diverter valve 分流阀vapor-liquid separator气液分离器vacuum modulator 真空调节器五timing 正时、定时air-fuel ratio 空燃比stoichiometric ratio 理论空燃比mixture 混合气top dead center（TDC）上止点bottom dead center（BDC）下止点bore 气缸直径、孔径crankpin 连杆轴颈、曲柄销throw 曲柄半径displacement 排量compression ratio 压缩比four-stroke engine 四冲程发动机intake stroke 进气冲程compression stroke 压缩冲程power stroke 做功行程exhaust stroke 排气行程preignition 提前点火valve overlap 气门重叠六two-stroke engine 二冲程发动机truck 货车、卡车bus 公共汽车Mercedes-Benz 梅赛德斯奔驰pickup truck 皮卡camper 露营车travel trailer 旅行拖车high-pressure injection高压喷射low-pressure injection低压喷射injector 喷油器、喷嘴psi 磅/平方英寸（英制压强单位）photochemical smog 光化学烟雾outboard motor 舷外发动机snowmobile 摩托雪橇chain saw 链锯、电锯reed valve 簧片阀lubricant 润滑剂、润滑油scavenging 扫气General Motors 通用汽车blower 扫气泵rotor 转子coal-fired 燃煤的、烧煤的nuclear-powered 核动力的drivability 动力性、驱动性能generator 发电机transaxle 变速差速器、联合传动器electronic controller 电子控制器downshift 降档manual transmission手动变速器hydrogen 氢carbon dioxide 二氧化碳oxygen 氧methanol 甲醇spacecraft 航天器、宇宙飞船anode 正极、阳极cathode 阴极、负极七oil pan 油底壳、机油盘water jacket 水套cylinder sleeve 气缸套dry sleeve 干缸套wet sleeve 湿缸套warpage 变形liner 衬套、衬垫bearing 轴承harmonic balancer vibration damper 扭转减震器timing gear 正时齿轮connecting rod journal 连杆轴颈main(bearing)journal主轴颈counterweight 平衡重thrust surface 推力面drive flange 传动法兰盘、凸缘fillet 圆角nose （曲轴）前端pulley 皮带轮air conditioning 空调bearing cap 轴承盖copper 铜lead 铅Babbitt 巴氏合金tin 锡bearing clearance 轴承间隙thrust bearing 推力轴承、止推轴承thrust washer 推力垫圈、止推垫圈piston ring 活塞环compression ring 气环oil control ring 油环piston pin 活塞销lock ring 锁环piston land 活塞顶部heat dam 绝热槽piston head 活塞头部piston skirt 活塞裙部ring groove 活塞环槽piston pin bushing 活塞销衬套ring end gap 活塞销开口间隙ductile iron 球墨铸铁chromium 铬molybdenum 钼torsional ring 扭曲环chrome-plated 镀铬的rod cap 连杆盖bearing insert 轴承衬套八cross-flow head 横流式气缸盖coolant 冷却液head gasket 气缸垫wedge-shapedcombustion chamber 楔形燃烧室hemisphericalcombustion chamber 半球形燃烧室open combustionchamber 开式燃烧室、统一式燃烧室pre-combustionchamber 预燃式燃烧室valve seat 气门座valve guide 气门导管retainer 弹簧座valve spring 气门弹簧high-chrome steel 高铬钢stellite 钴铬钨硬质合金keeper 锁紧装置valve stem 气门杆lifter 挺柱pushrod 推杆rocker arm 摇臂valve train clearance 气门间隙variable valve timing 可变气门正时九oil pressure regulator机油压力调节器main oil gallery 主油道oil screen 机油滤网oil pressure sensor 机油压力传感器dashboard 仪表板sump 机油箱、油底壳baffle 挡板gear-type oil pump齿轮油泵rotor oil pump 转子油泵pressure regulator valve调压阀十water pump 冷却水泵pressure cap 压力水箱盖fan 冷却风扇temperature indicator温度指示器air-cooled system 风冷系统liquid-cooled system 水冷系统transmission cooler 自动变速箱油冷却器expansion tank 膨胀水箱housing 外壳impeller 叶轮、转子hub 轮毂pulley 皮带轮closed cooling system闭式冷却系统十一electronic carburetor 电控化油器fuel vapor line 燃油蒸汽管fuel injector pump 喷油泵nozzle 喷嘴、管嘴plastic 塑料fuel cap 油箱盖filler neck 油箱填充口颈fuel metering unit 油量计量装置mechanical fuel pump 机械燃油泵electrical fuel pump 电动燃油泵fuel pressure regulator 燃油压力调节器injector fuel rail 燃油分配管、燃油轨direct injection system 直接喷射式燃料系统indirect injection system 非直喷式燃料系统port fuel injection（PFI）进气道燃油喷射throttle body injection （TBI）气门体燃油喷射multiple-point fuel injection 多点燃油喷射single-point fuel injection 单点燃油喷射continuous injection 连续喷射十二dry-type air filter 干式空气滤清器exhaust pipe 排气管undercarriage 底盘、下部结构fiberglass 玻璃纤维glass pack muffler 玻璃纤维消声器supercharging system 进气增压系统turbocharger 涡轮增压十三conventional ignitionsystem 传统点火系统primary circuit 初级回路（低压回路）secondary circuit 次级回路（高压回路）ballast resistor 附件电阻、稳流电阻crank 起动、摇转primary winding 初级线圈、一次绕组breaker 断电器secondary winding 次级线圈、二次绕组condenser 电容器arc 电弧distributor cap 分电器盖coil tower 点火线圈顶端接头surge 电涌振荡distributor shaft 分电器轴firing order 点火顺序electronic ignitionsystem 电子点火系统semiconductor 半导体electronic spark timing（EST）电子点火正时ignition control（IC）点火控制hight energy ignition（HEI）module 高能点火模块computer-controlledcoil ignition system 微机控制线圈点火系统electronic ignition（EI）电子点火distributorless ignitionsystem 无分电器点火系统ignition module 点火控制模块direct ignition system直接点火系统cableless EI system 无高压线电子点火系统十四。
汽车专业英语汇总
汽车专业英语汇总一、Vehicle classification 汽车分类1.1 Car 轿车1.2 Bus 客车1.3 Motor truck 货车1.4 special purpose vehicle 专用汽车二、Vehicle construction 汽车构造2.1 Main components of vehicle 汽车主要组成2.2 Vehicle performance 汽车性能 2.3 engine position 发动机布置三、Vehicle dimensions汽车尺寸四、Wheel alignment前轮定位五、Diameter of turning circle 转弯直径第二类ENGINE 发动机一、Engine construction 发动机构造二、Essential term 基本术语三、Engine operation principle发动机工作原理3.1 Four-stroke gasoline engine operationprinciple3.2 Four-stroke diesel engine operationalprincipleprinciple3.4 Two-stroke diesel engine operation principle二冲程柴油机工作原理四、Engine performance 发动机性能5.2 Piston,connecting rod 活塞连杆组7.5 Carburetor 化油器7.6 Carburetor elements化油器零件7.7 Carburetor control 化油器操纵件8.3 Injection pump 喷油泵8.4 Injection 喷油器九、Exhaust system 排气系统十、Turbo-supercharging 蜗轮增压10.1 Turbocharging system 蜗轮增压系统12.3 Fan,water pump 风扇，水泵12.4 Air cooling system 风冷系十三、Engine-lubrication system13.2 Oil pump 机油泵十五、Engine-starting system发动机起动系15.2 Electric starter 电动起动机16.2 Gas turbine 燃气轮机16.3 Stirling engine 斯特林发动机（热气机）第三类 CHASSIS 底盘一、Drive line 传动系1.2 Friction clutch 摩擦离合器1.3 Hydrodynamic coupling 液力偶合器1.7 Automatic transmission 自动变速器1.8 Transfer case 分动器1.10 Flexible coupling 挠性联轴节前轮独立悬架2.8 Rear wheel independent suspension后轮独立悬架2.9 Leaf spring 钢板弹簧2.10 Air suspension 空气悬架2.11 Hydro-pneumatic spring 液压充气弹簧2.13 Cam hydraulic shock absorber凸轮式液压减振器4.2 Drum brake4.4 Hand brake 手制动器 （parking brake 驻车制动器）4.5 hydraulic brake system 液压制动系 制动主缸，制动轮缸 4.7 Compressed-air brake system 气压制动系4.8 Anti-lock braking system 防抱死制动系第四类、BODY AND ACCESSORIES 车身及附属装置一、Car body 轿车车身二、All-steel body 全钢车身四、Bus body 大客车车身七、Cab 驾驶室十二、Compressor 压缩机十三、Lighting 照明十五、Turnsignal lamp 转向灯. Word 文档。
汽车专业英语
Accommodation 适应性Aerodynamics 空气动力学Air Conditioner 空调Air Drag 风阻Air Suspension 空气悬挂Analysis 分析Anti Corrosion 防腐Anti Rust 防锈Ashtray 烟灰盒Assembly 装配Assistant’s seat 副驾驶座Attaching Parts 附件Azimuth 方位（角）（极坐标）Back Angle 靠背角Backrest 靠背Backup Lamp 倒车灯Binocular Obstruction 双眼盲区BIW （Body-In-White）白车身Blower 风机Body 车身,车体Bolt 螺栓Bonneted Cab 凸头驾驶室Bracket 托架Breakdown 分块Bumper 保险杠Bushing 衬套Case 壳体Caution Plate 警告牌Centroid 重心Cigarette Lighter 点烟器Chassis 底盘Chassis Frame 车架Check Arm 限位器Clip 卡扣Cluster Meter 组合仪表盘Coat Hanger 衣帽架Coat Hook 衣帽钩Collar 套环Combination Switch 组合开关Comfort 舒适性Component 总成Concealed Wipers 隐藏式雨刮器Condenser 冷凝器Contour 轮廓线Controls 控制件Convex Mirror 凸面镜Coolant 冷却液Cooler 制冷器Crash 碰撞Cup Holder 水杯架Curtain 窗帘Curtain Rail 窗帘滑轨Curvilineal 曲线的Dash Board 前围内板Delivery of the Drawing 出图Displacement 位移Door Check 限位器Door Header Rail 车门顶轨Door Lock 车门锁Door Opening 门洞Door Outer Handle 车门外手柄Door Outer Panel 车门外板Door Panel 门护板Door Pocket 门袋Door Regulator 车门玻璃升降器Door Sash 车门窗框Door Striker 锁环Door Trim 车门护板Door Ventilator 三角窗Drip Rail 滴水凹槽顶轨Drive Configuration 驱动形式Dummy Plate 平衡板Dynamic 动态的Ellipsoid Surface 椭球面Emblem 商标Engine 发动机Engineering 工程Entrance Handrail 上车门扶手Entry ＆Exit 进出Ergonomics 人机工程学Eyellipse 眼椭圆Fatigue Analysis 疲劳分析FEM (Finite Element Method）有限元Fender 翼子板Fender Protector 挡泥护板Fender Stay 挡泥撑条Fender Welt 挡泥衬板Field of View 视野Finish Washer 精加工垫圈Fire Fighting Truck 消防车Fixed 固定的Flange Bolt 凸缘螺栓Fleece 绒毛织物Floor Insulator 地板隔热层Fluid Reservoir 贮液罐Fog Lamp 雾灯Fore/aft 前后Forward Control 平头Frame 车架Front Overhang 前悬Front Panel 前挡板,前围外板Front Turn Signal Lamp 前转向灯Fuse ＆Relay Box 保险丝和继电器箱Garnish 装饰板Gauge 量表Glare—free 防眩目Glass Run Channel 玻璃滑槽Glazing Rubber Plate 镶玻璃用橡胶板Glove Box 杂物盒Gradeability 爬坡度Grille 格栅Grip 扶手Grommet 密封圈Ground Clearance 离地间隙Halogen Headlamp 卤素大灯Handle Cover 手柄罩Head Contour 头廓包络线Head Restraints 头枕Headlamp 前大灯Headliner 顶棚Headlining 顶棚内饰Headrest 头枕Heater 加热器Heater Plumbing 取暖装置管路Height Adjuster 高度调节器High-mount 高位Hinge 铰链Hinge Bracket 铰链托架Holder 支架Hood 发动机罩Hook 挂钩Hose 软管Impact 碰撞In—line 直列Ingress/egress 进出Inside Lock Knob 内锁止按钮Instrument Panel 仪表板Interior Trim 内饰Intermittent Wiper 间歇式刮水器Joint 接头Joint Duct 连接管道Kinematics 运动学Lateral 横向Lever 杆籁绅士Plate 牌照籁绅士Plate Bracket 牌号托架籁绅士Plate Lamp 车牌灯Lift-up Type 翻转式（前围外板）Linear 线性的Load 载荷Lock Cylinder ＆Key 锁芯和钥匙Longitudinal 长度方向的Loose Panel 可卸盖板Lower Apron 下挡板Lumbar Support 腰托Luxury Interior Level 豪华内饰Mud Guard 挡泥板Mud Shield 挡泥板（侧）Male—to—Female Ration 男女比例Manikin 人体模型Manoeuvrable 操纵灵活的Meeting Minutes 会议纪要Member 横梁Meter ＆Gauge 仪表盘Meter Cable 仪表电缆Meter Cluster 仪表束Meter Cover 仪表面罩Meter Face 仪表面Meter Hood 仪表罩Milling 铣Mirror Holder 后视镜支架Model 模型Moquette 绒面Mount 悬置Movable Part 运动件Mudguard 挡泥板Muffler 排气消声器Muscular Contour 强壮的外形（造型风格)））Non—linear 非线性的Nozzle 喷嘴Nut 螺母Operation Hardware 开闭、锁紧装置Optimization 优化Ornament 标识Outlet 出风口Overhead Console Box 高架箱Packing 衬垫Parking Brake Lever 驻车制动手柄Percentile 百分位Perimeter 周长、周边Pillar 立柱Pin 销Pivot Point 关节点Plain Washer 平垫圈Plan View 俯视图Plate ＆Label 名牌和标识Plate Nut 板螺母Pneumatic Spring 空气弹簧Pocket 凹槽Pocket Facing 凹槽镶面Power Steering 动力转向Presentation 展示Push Button 按钮Push-on Spring Nut 顶推弹簧螺母Quarter Panel 后顶盖侧板Quarter Window 侧车窗Radiator 散热器Raised Roof 高顶Rear Overhang 后悬Rear View Mirror 后视镜Rear Wall 后围Reclining 倾斜Reflector 反射板Regulation 法规Reinforcement 加强件Rendering 效果图Requirement 要求Resin 树脂Retainer 护圈Rigidity 刚度Rivet 铆钉Roof Console 高架箱Roof Hatch 天窗Roof Panel 车顶板Room Lamp 室内灯Root—Mean-Square 均方根Round Oval Instrumentation 环抱式仪表板Safety 安全性Screw 螺钉Screw Grommet 密封圈螺钉Scuff 压条（门槛处）Seat Bench 长排座Seat Support 座椅支架Seat Track 座椅导轨Self—Supporting 自承载式Service Parts 修理配件Set Screw 定位螺钉Shim 调整垫片Shin—Knee Contour 膝部包络线Shock Absorber 减振器Side View 侧视图Sight Line 视线Silencer 消声器Sill 横梁Simulation 模拟Sketch 草效果图Sleeper 卧铺Sleeping Bed 卧铺Sleeping Berth 卧铺Slide Adjuster 前后滑动调节器Snap Ring 开口环Snorkel 进气管Snowplow 除雪车Spacer 隔环Speedometer 车速仪Splash Apron 侧挡泥板Spot Welding 点焊Static 静态的Steering Column 转向柱Steering Column Adjuster 转向柱调整器Steering Gear 转向机构Steering Wheel 方向盘Step Plate 踏脚板Step Protector 脚踏板护板Stiffener 加强肋Stiffness 刚度Stop Lamp 制动灯Stopper 挡块Strain 应变Strength 强度Stress 应力Structure 结构Styling 造型Sun Visor 遮阳板Surfacing 线图Suspension 悬架Switch 开关Tachograph & Speedometer 自记式转速记和车速表Tachometer 发动机转速表Tail Lamp 尾灯Tapping Screw 自攻螺钉Template 模板Ticket/Card Holder 名片夹Tilt 翻转(驾驶室）Tipper 自卸车Tonnage 吨位Torsional Stiffness 扭转刚度Tread 轮距Trim 饰件Trim Panel 装饰板Turning Radius 转弯半径Upper Console 高架箱Variant 变形车Ventilation 通风Vertical 垂直方向的Vinyl 乙烯基Washer 垫圈Water Proof Film 防水层Weather Strip 密封条Wear—Resistant 防磨Windscreen 风窗Windshield 风窗Windshield Washer 挡风玻璃洗涤器Windshield Wiper 挡风玻璃刮水器Wiper 刮水器Wiper Arm 刮臂Wiper Blade 刮片Wiper Link Assembly 刮水器连杆组件Wiring Harness 线束07-0轮椅升降机Wheel chair lift图例legend工位station吊运装置overhead hoist更衣室restroom1号厂房工艺布置方案图proposal of the Plant I layout合笼mate底盘平移台chassis shuttle车辆转移台bus transfer前围角板front wall angle cover后围侧板rear wall side cover保险杠bumper三类底盘three type chassis左侧围应力蒙皮R/S stretching skin （road side）中涂floating coat拼装台collector切割轮口wheel —arch cutting内饰trim线束harness返工re-doing轮罩护板wheel house发车前准备pre-delivery举升hoist小批量产品be pilot2 套two kits配电站power transformer substation裙板skirt发动机托架engine holding frame诊断报警系统diagnosis and alarming system互换性interchangeability缩微图纸microfiche files总装final assembly磷化phosphating仪表板dash board切齐trimming结构完整性structure integrity自动愈合的防腐材料self-healing corrosion preventative material 长途客车inter-city bus改装厂refitting factory遮阳板sun visor随车工具tool box钢化玻璃toughened grass异形钢管special steel pipe全天候空调系统full range A/C强制通风ram-air ventilation停机时间downtime无公害柴油clean diesel宽敞悬臂式座椅roomy cantilevered seat防滑地板no—skid floor织物纹里铝合金textured aluminum extrution 爬坡能力grade ability排水阀drain valve除湿器moisture ejector怠速时at idle琴式驱动桥banjo type drive axle通风口duct恒温控制thermostatic control平衡水箱surge tank变光开关simmer switch消音器muffler防破坏vandal resistant聚碳化透镜poly—carbonate len镀锌板galvanized plate搭接lap亮丽的外表smart apperance隐藏式固定concealed fastening水洼ponding发动机中置式客车bus with under floor engine 组合式客车车身modular bus body薄壳式结构shell construction衬垫pad空气导流板air deflector搁梁shelf beam腰梁waist rail梭梁stabilizing beam腰带式安全带diagonal safety belt压条trim strip嵌条insertion strip翼板fender斜撑bracing piece转向盘回正性试验test of steering wheel returnability转向盘转角脉冲试验steering wheel impulse input test转向盘转角阶跃输入试验steering wheel step input or transient state yaw response test极限侧向加速度试验limiting lateral acceleration test汽车平顺性随机输入行驶试验automobile ride random input running test汽车平顺性单脉冲输入行驶试验automobile ride single pulse input running test汽车悬挂系统固有频率与阻尼比的测定试验measurement of natural frequency and damping raito of suspension 功率突然变化影响试验test of effect of sudden power change收油门后控制试验test of control at breakway横风稳定性试验test of crosswind stability反冲试验kick—back test轮胎爆破响应时间试验test of burst response of tyre绕过障碍物试验obstacle avoidance test移线试验lane change testJ型转弯试验test of J turn频率响应时间试验frequency response test瞬态响应时间试验transient response test阶路响应时间试验step response test脉冲响应试验pulse response test静态操舵力试验static steering effort test悬架举升试验jack—up test of suspension耐翻倾试验test of overturning immunity轮辋错动试验rim slip test风洞试验wind tunnel test制动稳定性试验test of braking stability最小转弯直径试验minimum turning diameter test操舵力试验steering effort test汽车发动机类型type发动机engine内燃机intenal combusiton engine动力机装置power unit汽油机gasoline engine汽油喷射式汽油机gasoline—injection engine火花点火式发动机spark ignition engine压燃式发动机compression ignition engine往复式内燃机reciprocating internal combustion engine 化油器式发动机carburetor engine柴油机diesel engine转子发动机rotary engine旋轮线转子发动机rotary trochoidal engine二冲程发动机two—stroke engine四冲程发动机four—stroke engine直接喷射式柴油机direct injection engine间接喷射式柴油机indirect injection engine增压式发动机supercharged engine风冷式发动机air—cooled engine油冷式发动机oil—cooled engine水冷式发动机water-cooled engine自然进气式发动机naturally aspirated engine煤气机gas engine液化石油气发动机liquified petroleum gas engine 柴油煤气机diesel gas engine多种燃料发动机multifuel engine石油发动机hydrocarbon engine双燃料发动机duel fuel engine热球式发动机hot bulb engine多气缸发动机multiple cylinder engine对置活塞发动机opposed piston engine对置气缸式发动机opposed—cylinder engine十字头型发动机cross head engine直列式发动机in—line engine星型发动机radial engine筒状活塞发动机trunk—piston engine斯特林发动机stirling engine套阀式发动机knight engine气孔扫气式发动机port—scavenged engine倾斜式发动机slant engine前置式发动机front-engine后置式发动机rear—engine中置式发动机central engine左侧发动机left—hand engine右侧发动机right—hand engine短冲程发动机oversquare engine长冲程发动机undersquare engine等径程发动机square engine顶置凸轮轴发动机overhead camshaft engine双顶置凸轮轴发动机dual overhead camshaft engine V形发动机V—engine顶置气门发动机valve in—head engine侧置气门发动机side valve engine无气门发动机valveless engine多气门发动机multi—valve engine卧式发动机horizontal engine斜置式发动机inclined engine立式发动机vertical engineW形发动机I形发动机I-engineL形发动机L—engineF形发动机F—engine性能performance二冲程循环two—stroke cycle四冲程循环four—stroke cycle狄塞尔循环diesel cycle奥托循环otto cycle混合循环mixed cycle定容循环constant volume cycle 工作循环working cycle等压循环constant pressure cycle 理想循环ideal cycle热力循环thermodynamic cycle 冲程stroke活塞行程piston stroke长行程long stroke上行程up stroke下行程down stroke进气行程intake stroke充气行程charging strokecompression stroke爆炸行程explosion stroke膨胀行程expansion stroke动力行程power stroke排气行程exhaust stroke膨胀换气行程expansion—exchange stroke换气压缩行程exchange—compression stroke止点dead center上止点top dead center(upper dead center)下止点lower dead center（bottom dead center）上止点前budc（before upper dead center）上止点后atdc（after top dead cetner）下止点前bbdc（before bottom dead center)下止点后abdc（after bottom dead center）缸径cylinder bore缸径与行程bore and stroke空气室energy chamber气缸余隙容积cylinder clearance volume燃烧室容积combustion chamber volume气缸最大容积maximum cylinder volume压缩室compression chamber排气量displacement发动机排量engine displacement活塞排量piston swept volume气缸容量cylinder capacity单室容量single-chamber capacity容积法volumetry压缩比compression ratio临界压缩比critical compression ratio膨胀比expansion ratio面容比surface to volume ratio行程缸径比stroke-bore ratio混合比mixture ratio压缩压力compression pressure制动平均有效压力brake mean effective pressure(bmep) 空燃比air fuel ratio燃空比fuel air ratio燃料当量比fuel equivalence ratio扭矩torque单缸功率power per cylinder升功率power per liter升扭矩torque per liter升质量mass per liter减额功率derating power输出马力shaft horsepower马力小时,马力时horsepower-hour总马力gross horse power总功率gross power净功率net power燃油消耗量fuel consumption比燃料消耗率specific fuel consumption 空气消耗率air consumption机油消耗量oil consumption有效马力net horse power额定马力rated horse power马力重量系数horsepower-weight factor 制动功率brake horse power制动热效率brake thermal efficiency总效率overall efficiency排烟极限功率smoke limiting horsepower 功率曲线power curve机械损失mechanical loss机械效率mechanical efficiency有效热效率effective thermal efficiency 充气系数volumetric efficiency过量空气系数coefficient of excess air适应性系数adaptive coefficient扭矩适应性系数coefficient of torque adaptibility转速适应性系数speed adaptive coefficient强化系数coefficient of intensification校正系数correction factor换算系数conversion factor活塞平均速度mean piston speed发动机转速engine speed (rotational frequency）怠速转速idling speed经济转速economic speed起动转速starting speed最低稳定工作转速lowest continuous speed with load 最大扭矩转速speed at maximum torque最高空转转速maximum no load governed speed 调速speed governing超速overspeed怠速idling转速波动率speed fluctuation rate工况working condition(operating mode）额定工况declared working condition变工况variable working condition 稳定工况steady working condition 空载no-load全负荷full load超负荷overload部分负荷part load充量（进气）charge旋转方向direction of rotation顺时针clockwise逆时针counter—clockwise左转left—hand rotation右转right—hand rotation外径major diameter中径pitch diameter内径minor diameter径向间隙radial clearance发动机性能engine performance加载性能loading performance起动性能starting performance加速性能acceleration performance 动力性能power performance排放性能emission performance空转特性no load characteristics负荷特性part throttle characteristics调速特性governor control characteristics万有特性mapping characteristics稳定调速率steady state speed governing rate气缸体和气缸盖cylinder block and head气缸体cylinder block整体铸造cast inblock (cast enblock）发动机罩engine bonnet气缸体加强筋engine block stiffening rib气缸cylinder（转子机）缸体stator07—0 reock frameadhanism casingacer环ad ring gasketad gasketer(cylinder sleeve)r linerer lineretplugallrtte bottum转子机）radius转子机）widthn chamberustion chamber combustion chamberrustion chamber室mbustion chamber室combustion chamber室cal combustion chamberction combustion chamberon chambertion combustion chamberustion chamberay chamber烧室mberhamber比io of combustion cahmber比olume ratio of combustion chamberof combustion chamber passage口breather座earing bush seat罩rive（gear）cover孔盖door门explosion proof doorng caphanism coververair receiver塞iston塞tonpistonistond piston（convex head piston) ead pistonpistonn塞c piston塞earance piston活塞piston活塞led piston活塞oled pistononedd衬簧expander裙tkbossbushing销ng piston pin销g piston pin活塞销piston pin环piston ringpiston ringiston ringngne ringr ringringcontrol ring载双坡口油环loaded slotted oil control ring elled oil control ringvel topvel bottom环ege oil control ring ngted piston ringexpandergrooveland面g构rod杆机构cated connecting rod 杆机构ecting rod杆机构necting rodrodrod small endg rod big endrod shankecting rodblade connecting rod ecting rode connecting rod connecting rod rod caprod bearingcrankshaftcrankshaftd crankshaftrankshaft曲轴ankshaftfront endmain journalal overlapng承thrust bearing earing shelloil passageeuseelalancereightvibration damperanceralanceralancersprocketalhaft通风装置nkcase ventilating system ng gearindle矩oment of inertiaarksystemshaft length性力ng inertia force，1st order 性力ng inertia force，2nd order inertia force轴camshaft轴camshaft机构rive轴haftearing journalearing轮ccentricprocket齿轮ming gearear wheel）:swm45100 FanE『翻译中国』2004-5—27 14：07:30 te gear(counter gear）aft gearaft轴on imput shaft轴on output shaft齿轮轴on drive gear shafton main shaft轴on countershaft刚度shaft（变速比）on gear ratiorepressure力odulator pressureressureor or trimmer pressurere（input pump )置充油压力mic unit change pressure（output pump ）il pumpegulator vavle阀gulator valve旁通阀bypass valvealvelvee生器n generatortor(shift torwer)veve控制阀ntrol valve锁止ockup换档系统utomatic control system 换档系统-hydraulic automatiec换档shfititshfithiftiftte shiftresisulepower shift程automatic shift automatic shft lementer（gear shift lever））变速杆ctork (gear shift fork）杆ar shift forkpedal叉道轨）ge(direct control）速ft （handle change）controle07-空档位置neutral position直接驱动direct drive高速档top gear（high gear）低速档bottom gear（low speed gear)第一档first gear第二档second gear超速档overdirve gear经济档economic gear倒档reverse gear爬行档creeper gear驱动特性drive performance反拖特性coast performance定输入扭矩特性constant input torque performance全油门特性full throttle performance寄生损失特性no load （parasitic losses）performance 原始特性primary characteristic响应特性response characteristic吸收特性absorption characteristic全特性total external characteristic输入特性characteristic of enhance输出特性characteristic of exit力矩特性torque factor（coefficient of moment）过载系数overloading ratio变矩系数torque ratio能容系数capacity factorr几何相似geometry similarity运动相似kinematic similarity动力相似dynamic similarity透穿性transparency万向节和传动轴universal joint and drive shaft万向节universal joint非等速万向节nonconstant velocity universal joint等速万向节constant velocity universal joint准等速万向节near constant velocity universal joint自承式万向节self—supporting universal joint 非自承式万各节non self suporting universal joint 回转直径swing diameter等速平面constant velocity plane万向节夹角true joint angle十字轴式万向节cardan (hookes)universal joint 万向节叉yoke突缘叉flange york滑动叉slip yoke滑动节,伸缩节slip joint花键轴叉slip shaft yoke轴管叉（焊接叉）tube（weld yoke）十字轴cross（spider）十字轴总成cross assembly挠性元件总成flexible universal joint球销式万向节flexible member assembly双柱槽壳housing球环ball球头轴ball head球头钉button中心球和座centering ball and seat球笼式万向节rzeppa universal joint钟形壳outer race星型套inner race保持架cage可轴向移动的球笼式万向节plunging constant velocity joint筒形壳cylinder outer race柱形滚道星形套inner race withcylinder ball grooves 偏心保持架non-concentric cage滚动花键球笼式万向节ball spline rzeppa universal joint外壳outer housing内壳体inner housing球叉式万向节weiss universal joint球叉ball yoke定心钢球centering ball三球销万向节tripod universal joint三柱槽壳housing三销架spider双联万向节double cardan universal joint凸块式万向节tracta universal joint凸块叉fork yoke榫槽凸块tongue and groove couplijng凹槽凸块groove coupling传动轴drive shaft(propeller shaft）传动轴系drive line传动轴形式drive shaft type两万向节滑动的传动轴two —joint inboard slip ddiveshaft 两万向节外侧滑动传动轴two joint ouboard slip drive shaft 单万向节传动轴single joint coupling shaft组合式传动轴unitized drive shaft传动轴减振器drive shaft absorber传动轴中间轴承drive shaft center bearing传动轴管焊接合件weld drive shaft tube assembly传动轴特征长度drive shaft length传动轴谐振噪声resonant noise of rive shaft传动轴的临界转速critical speed of drive shaft传动轴总成的平衡balance of drive shaft assembly允许滑动量slip相位角phase angle传动轴安全圈drive shaft safety strap驱动桥drive axle(driving axle)类型type断开式驱动桥divided axle非独立悬架式驱动桥rigid dirve axle独立悬架式驱动桥independent suspension drive axlesteering drive axle贯通式驱动桥tandem axles“三速”贯通轴"three—speed" tandem axles单驱动桥single drive axle多桥驱动multiaxle drive减速器reducer主减速器final drive单级主减速器single reduction final drive双级主减速器double reduction final drive前置式双级主减速器front mounted double reduction final drive后置式双级主减速器rear mounted double reduction final drive上置式双级主减速器top mounted double reducton final drive行星齿轮式双级主减速器planetary double reduction final drive贯通式主减速器thru-drive双速主减速器two speed final drive行星齿轮式双速主减速器two speed planetary final drive双级双速主减速器two speed double reduction final drive轮边减速器wheel reductor（hub reductro）行星圆柱齿轮式轮边减速器planetary wheel reductor行星锥齿轮式轮边减速器differential geared wheel reductor(bevelepicyclick hub reductor) 外啮合圆柱齿轮式轮边减速器spur geared wheel reductor差速器锥齿轮式差速器bevel gear differential圆柱齿轮式差速器spur gear differential防滑式差速器limited —slip differential磨擦片式自锁差速器multi—disc self -locking differential凸轮滑滑块自锁差速器self—locking differential with side ring and radial cam plate 自动离合式自锁差速器automotive positive locking differential强制锁止式差速器locking differential液压差速器hydraulic differential轴间差速器interaxial differential差速器壳differential carrieer（case）主降速齿轮final reduction gear驱动轴减速比axle ratio总减速比total reduction ratio主降速齿轮减速比final reduction gear ratio双减速齿轮double reduction gear差速器主齿轮轴differential pinion-shaft差速器侧齿轮differential side gear行星齿轮spider gear(planetary pinion）螺旋锥齿轮spiral bevel gear双曲面齿轮hypoid gear格里林齿制gleason tooth奥林康型齿制oerlikon tooth锥齿轮齿数number of teeth in bevel gears and hypoid gears锥齿轮齿宽face width of tooth in bevel gears and hypoid gears 平面锥齿轮plane bevel gear奥克托齿形octoid form平顶锥齿轮contrate gear齿面接触区circular tooth contact齿侧间隙backlash in circular tooth差速器十字轴differential spider差速器锁止机构differential locking —device差速器锁止系数differential locking factor差速器壳轴承carrier bearing桥壳axle housing整体式桥壳banjo housing可分式桥壳trumpet-type axle housing组合式桥壳unitized carrier—type axle housing对分式桥壳split housing冲压焊接桥壳press-welding axle housing钢管扩张桥壳expanded tube axle housing锻压焊接桥壳forge welding axle housing整体铸造式桥壳cast rigid axle housing半轴axle shaft全浮式半轴full—floating axle shaft半浮式半轴semi-floating axle shaft四分之三浮式半轴three—quarter floating axle shaft 驱动桥最大附着扭矩slip torque驱动桥额定桥荷能力rating axle capactiy驱动桥减速比driveaxle ratio驱动桥质量drive axle mass单铰接式摆动轴single—joint swing axle双铰接式摆动轴double joint swig axle悬架系suspension system悬架suspension类型type非独立悬架rigid axle suspension独立悬架independent suspension平衡悬架equalizing type of suspension组合式悬架combination suspension可变刚度悬架。