最全模具行业术语英文翻译
(完整版)模具专业英文术语大全
模具英语专业术语模具述语一、入水：gate进入位： gate location水口形式：gate type大水口：edge gate细水口： pin-point gate水口大小：gate size转水口： switching runner/gate唧嘴口径： sprue diameter二、流道: runner热流道： hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance热嘴： hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头： connector plug插座： connector socket密封/封料： seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件： mold components 三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin顶针板：ejector retainner plate托板： support plate螺丝： screw管钉：dowel pin 开模槽：ply bar scot内模管位：core/cavity inter-lock顶针： ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter模胚（架）： mold base上内模：cavity insert下内模：core insert行位（滑块）： slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴： sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cuton B-plate.不准用镶件： Do not use (core/cavity) insert用铍铜做镶件： use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length 稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrodeMold & die components 模具单元Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Pressing dies 压模Quick die change systems 速换模系统Quick mold change systems 快速换模系统三、模具塑料模具 mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA 板A plateB 板B plate支承板 support plate方铁 spacer plate底针板 ejector plate面针板 ejector retainer plate回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush直导套 Straight Guide bush动模座板Bottom clamp plateMoving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道 sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould 动模movable mould, movable half上模upper mould， upper half下模lower mould， lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft 滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具 three plate mould脱模ejection换模腔模具 interchangeable cavity mould 脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining 数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine compre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具（移转成型用模具）encapsulation molding 低压封装成型（射出成型用模具）two plate 两极式（模具）well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spindle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道welding line 熔合痕eject pin 顶出针knock pin 顶出销return pin 回位销反顶针sleave 套筒stripper plate 脱料板insert core 放置入子runner stripper plate 浇道脱料板guide pin 导销eject rod (bar)（成型机）顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orientation 定向sprue gate 射料浇口，直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆) slag well 冷料井side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口subarine gate 潜入式浇口tunnel gate 隧道式浇口pin gate 针点浇口Runner less 无浇道(sprue less)无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣emboss 凸点dome 凸圆semi-shearing 半剪stamp mark 冲记号deburr or coin 压毛边punch riveting 冲压铆合side stretch 侧冲压平reel stretch 卷圆压平groove 压线blanking 下料stamp letter 冲字(料号) shearing 剪断tick-mark nearside 正面压印tick-mark farside 反面压印冲压名称类extension dwg 展开图procedure dwg 工程图die structure dwg 模具结构图material 材质material thickness 料片厚度factor 系数upward 向上downward 向下press specification 冲床规格die height range 适用模高die height 闭模高度burr 毛边gap 间隙weight 重量total wt.总重量punch wt.上模重量五金零件类inner guiding post 内导柱inner hexagon screw 内六角螺钉dowel pin 固定销coil spring 弹簧lifter pin 顶料销eq-height sleeves=spool 等高套筒pin 销lifter guide pin 浮升导料销guide pin 导正销wire spring 圆线弹簧outer guiding post 外导柱stop screw 止付螺丝located pin 定位销outer bush 外导套模板类top plate 上托板（顶板）top block 上垫脚punch set 上模座punch pad 上垫板punch holder 上夹板stripper pad 脱料背板up stripper 上脱料板male die 公模(凸模)feature die 公母模female die 母模(凹模)upper plate 上模板lower plate 下模板die pad 下垫板die holder 下夹板die set 下模座bottom block 下垫脚bottom plate 下托板(底板)stripping plate 内外打(脱料板)outer stripper 外脱料板inner stripper 内脱料板lower stripper 下脱料板零件类punch 冲头insert 入块(嵌入件)deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller 滚轴baffle plate 挡块located block 定位块supporting block for location定位支承块air cushion plate 气垫板air-cushion eject-rod 气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block 滑块塑料模具专业术语动模 movable mould moving half 定模座板 fixed clamp plate, top clamping plate. top plate 动模座板 moving clamp plate. bottom clamping plate. bottom plate上模座板 upper clamping plate下模座板 lower clamping plate凹模固定板 cavity-retainer plate型芯固定板 core-retainer plate凸模固定板 punch-retainer plate模套 chase. bolster. frame支承板 backing plate. supprr plate 垫块 spacer parallel支架 ejector housing. mould base leg 压力铸造模具 die-casting die压铸模零部件定模 fixed die, cover die定模座板 fixed clamping plate定模套板 bolstor, fixed die动模 moving die,ejector die动模座板 moving clamping plate直流道 sprue横流道 runner内浇口 gatelanded plunger mold||有肩柱塞式模具burnishing die||挤光模landed positive mold||有肩全压式模具button die||镶入式圆形凹模loading shoe mold||料套式模具center-gated mold||中心浇口式模具loose detail mold||活零件模具chill mold||冷硬用铸模loose mold||活动式模具clod hobbing||冷挤压制模louvering die||百叶窗冲切模composite dies||复合模具manifold die||分歧管模具counter punch||反凸模modular mold||组合式模具double stack mold||双层模具multi-cavity mold||多模穴模具electroformed mold||电铸成形模multi-gate mold||复式浇口模具expander die||扩径模offswt bending die||双折冷弯模具extrusion die||挤出模palletizing die||叠层模family mold||反套制品模具plaster mold||石膏模blank through dies||漏件式落料模porous mold||通气性模具duplicated cavity plate||复板模positive mold||全压式模具fantail die||扇尾形模具pressure die||压紧模fishtail die||鱼尾形模具profile die||轮廓模flash mold||溢料式模具progressive die||顺序模gypsum mold||石膏铸模protable mold||手提式模具hot-runner mold||热流道模具prototype mold||雏形试验模具ingot mold||钢锭模punching die||落料模lancing die||切口模raising(embossing)||压花起伏成形re-entrant mold||倒角式模具sectional die||拼合模runless injection mold||无流道冷料模具sectional die||对合模具segment mold||组合模semi-positive mold||半全压式模具shaper||定型模套single cavity mold||单腔模具solid forging die||整体锻模split forging die||拼合锻模split mold||双并式模具sprueless mold||无注道残料模具squeezing die||挤压模stretch form die||拉伸成形模sweeping mold||平刮铸模swing die||振动模具three plates mold||三片式模具trimming die||切边模unit mold||单元式模具universal mold||通用模具unscrewing mold||退扣式模具yoke type die||轭型模模具钢材 khuôn thépalloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 矽钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑胶覆面钢板塑件与模具compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具（移转成型用模具）encapsulation molding低压封装成型（射出成型用模具）two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Runner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量连接器connector端子terminal条型连接器bar connector阴连接器Housing阳连接器wafer线束wire harness间距space额定电压 rated voltage额定电流 rated current接触电阻contact resistance 绝缘电阻insulation resistance 超声波焊接ultrasonic welding 耐压withstand voltage针pin 物料编号part number导线wire基体金属Base metal电缆夹cable clamp倒角chamfer接触面积contact area接触件安装孔contact cavity 接触长度contact length接触件电镀层contact plating 接触压力contact pressure 接触件中心距contact space 接触簧片contact spring插孔socket contact法兰、凸缘Flange界面间隙interfacial gap键Key键槽keyway过渡段ramp屏蔽套shielding定位基准Datum reference扁平电缆flat cable ，Ribbon cable柔性印刷电线Flexible printed wiring多层印制电路Multilayer printed circuit焊盘pad图形pattern间距pitch负极Negative pole正极positive pole回流Reflow原理图Schematic diagram单面板single sided board双面板Two-sided board，Double-sided board表面安装surface Mounting翘曲warp， bow波峰焊wave soldering编织层braid同轴电缆coaxial cable电介质dielectric电缆中导线的头数ends外部干扰external interference填充物filler护套jacket比重specific gravity电阻的温度系数Temperature coefficient of resistance模具塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plate A板A plateB板B plate支承板 support plate方铁 spacer plate底针板 ejector plate面针板 ejector retainer plate回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush 直导套 Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate 凸模固定板punch-retainer plate 顶针ejector pin单腔模具single cavity mould 多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force 锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道 sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould 动模movable mould, movable half上模upper mould， upper half下模lower mould， lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core 螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具 interchangeable cavity mould 脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining 数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine模具零件Top Plate 上托板（顶板）Top Block 上垫脚Punch Set 上模座Punch Pad 上垫板Punch Holder 上夹板Stripper Pad 脱料背板Up Stripper 上脱料板Male Die 公模（凸模）Feature Die 公母模Female Die 母模（凹模）Upper Mold Plate 上模板Lower Mold Plate 下模板Die Pad 下垫板Die Holder 下夹板Die Set 下模座Bottom Block 下垫脚Bottom Plate下托板（底板）Stripping Plate 内外打（脱料板）Outer Stripper 外脱料板Inner Stripper 内脱料板Lower Stripper 下脱料板11 / 17Inner Guiding Post 内导柱Inner Hexagon Screw 内六角螺钉Dowel Pin 固定销Mould Coil Spring 模具弹簧Lifter Pin 顶料销Isoheight Sleeve 等高套筒Pin 销Lifter Guide Pin 浮升导料销Guide Pin 导正销Wire Spring 圆线弹簧Outer Guiding Post 外导柱Stop Screw 止付螺丝Located Pin 定位销Outer Bush 外导套Punch 冲头Insert 入块（嵌入件）Deburring Punch 压毛边冲子Groove Punch 压线冲子Stamped Punch 字模冲子Round Punch 圆冲子Special Shape Punch 异形冲子Bending Block 折刀Roller 滚轴Baffle Plate 挡块Located Block 定位块Supporting Block for Location 定位支承块Air Cushion Plate 气垫板Air-Cushion Eject-rod 气垫顶杆Trimming Punch 切边冲子Stiffening Rib Punch Stinger 加强筋冲子Ribbon Punch 压筋冲子Reel-stretch Punch 卷圆压平冲子Guide Plate 定位板Sliding Block 滑块Sliding Dowel Block 滑块固定块Active Plate 活动板Lower Sliding Plate 下滑块板Upper Holder Block 上压块Upper Mid Plate 上中间板Spring Box 弹簧箱Spring-Box Eject-rod 弹簧箱顶杆Spring-Box Eject-Plate 弹簧箱顶板Bushing Block Liner Bushing 衬套Cover Plate 盖板Guide Pad 导料块模具技术用语各种常用模具成形方式Accurate Die Casting 精密压铸Powder Forming 粉末成形Calendaring Molding 压延成形Powder Metal Forging 粉末锻造Cold Chamber Die Casting 冷式压铸Precision Forging 精密锻造Cold Forging 冷锻Press Forging 冲锻Compacting Molding 粉末压出成形Rocking Die Forging 摇动锻造Compound Molding 复合成形Rotary Forging 回转锻造Compression Molding 压缩成形Rotational Molding 离心成形Dip Mold 浸渍成形Rubber Molding 橡胶成形Encapsulation Molding 注入成形Sand Mold Casting 砂模铸造Extrusion Molding 挤出成形Shell Casting 壳模铸造Foam Forming 发泡成形Sinter Forging 烧结锻造Forging Roll 轧锻Six Sides Forging 六面锻造Gravity Casting 重力铸造Slush Molding 凝塑成形Hollow Blow Molding 中空（吹出）成形Squeeze Casting 高压铸造Hot Chamber Die Casting 热室压铸Swaging 挤锻Hot Forging 热锻Transfer Molding 转送成形Injection Molding 射出成形Warm Forging 温锻Investment Casting 精密铸造Matched Die Method 对模成形法Laminating Method 被覆淋膜成形Low Pressure Casting 低压铸造Lost Wax Casting 脱蜡铸造Matched Mould Thermal Forming 对模热成形模Close Mold 合模Demould 脱模脱模剂Mould Unloading 开模Eject 顶出Tool Change Retooling Die Changing 换模Mould Clamping 锁模各式模具分类用语Bismuth Mold 铋铸模Landed Plunger Mold 有肩柱塞式模具Burnishing Die 挤光模Landed Positive Mold 有肩全压式模具Button Die 镶入式圆形凹模Loading Shoe Mold 料套式模具Center-Gated Mold 中心浇口式模具Loose Detail Mold 活零件模具Chill Mold 冷硬用铸模Loose Mold 活动式模具Cold Hobbing 冷挤压制模法Louvering Die 百叶窗冲切模Composite Dies 复合模具Manifold Die 分歧管模具Counter Punch 反凸模Modular Mold 组合模具Double Stack Mold 双层模具Multi-Cavity Mold 多模穴模具Electroformed Mold 电铸成形模Multi-Gate Mold 复式浇口模具Expander Die 扩径模Offset Cold Bending Die 双折冷弯模具Extrusion Die 挤出模Stack Mold, Stack Injection Mould 叠层模Family Mold 反套制品模具Plaster Mold 石膏模Blank Through Dies 漏件式落料模Porous Mold 通气性模具Duplicated Cavity Plate 复板模Positive Mold 全压式模具Fantail Die 扇尾形模具Pressure Die 压紧模Fishtail Die 鱼尾形模具Profile Die 轮廓模Flash Mold 溢料式模具Progressive Die 顺序模Gypsum Mold 石膏铸模Portable Mold 手提式模具Hot-Runner Mold 热流道模具Prototype Mold 雏形试验模具原型模具Ingot Mold 钢锭模Punching Die 落料模Lancing Die 切口模切缝模Raising（Embossing）压花起伏成形Re-entrant Mold 倒角式模具Sectional Die 拼合模Runless Injection Mold 无流道冷料模具Sectional Die 对合模具Segment Mold 组合模Semi-Positive Mold 半全压式模具Shaper 定型模套Single Cavity Mold 单腔模具Solid Forging Die 整体锻模Split Forging Die 拼合锻模Split Mold 双并式模具Sprueless Mold 无注道残料模具Squeezing Die 挤压模Stretch Form Die 拉伸成形模Sweeping Mold 平刮铸模Swing Die 振动模具Three Plates Mold 三片式模具Trimming Die 切边模Unit Mold 单元式模具Universal Mold 通用模具Unscrewing Mold 退扣式模具Yoke Type Die 轭型模模具厂常用之标准零配件Air Vent Valve 通气阀Anchor Pin 锚梢Angular Pin 角梢Baffle 调节阻板Angular Pin 倾斜梢Baffle Plate 折流档板Ball Button 球塞套Ball Plunger 定位球塞Ball Slider 球塞滑块Binder Plate 压板Blank Holder 防皱压板Blanking Die 落料冲头Bolster 上下模板Bottom board 浇注底板Bolster 垫板Bottom Plate 下固定板Bracket 托架Bumper Block 缓冲块Buster 堵口Casting Ladle 浇注包Casting lug 铸耳Cavity 模穴（模仁）Cavity Retainer Plate 模穴托板Center Pin 中心梢Clamping Block 锁定块Coil Spring 螺旋弹簧Cold Punched Nut 冷冲螺母Cooling Spiral 螺旋冷却栓Core 心型Core Pin 心型梢Cotter 开口梢Cross 十字接头Cushion Pin 缓冲梢Diaphragm Gate 盘形浇口Die Approach 模头料道Die Bed 型底Die Block 块形模体Die Body 铸模座Die Bush 合模衬套Die Button 冲模母模Die Clamper 夹模器Die Fastener 模具固定用零件Die Holder 母模固定板Die Lip 模唇Die Plate 冲模板Die Set 冲压模座Direct Gate 直接浇口Dog Chuck 爪牙夹头Dowel 定位梢Dowel Hole 导套孔Dowel Pin 合模梢Dozzle 辅助浇口Dowel Pin 定位梢Draft 拔模锥度Draw Bead 张力调整杆Drive Bearing 传动轴承Ejection Pad 顶出衬垫Ejector 脱模器Ejector Guide Pin 顶出导梢Ejector Leader Bush 顶出导梢衬套Ejector Pad 顶出垫Ejector Pin 顶出梢Ejector Plate 顶出板Ejector Rod 顶出杆Ejector Sleeve 顶出衬套Ejector Valve 顶出阀Eye Bolt 环首螺栓Filling Core 填充型芯椿入蕊Film Gate 薄膜形浇口Finger Pin 指形梢Finish Machined Plate 角形模板Finish Machined Round Plate 圆形模板Fixed Bolster Plate 固定侧模板Flanged Pin 带凸缘针Flash Gate 毛边形浇口Flask 上箱Floating Punch 浮动冲头Gate 浇口Gate Land 浇口面Gib 凹形拉紧楔Goose Neck 鹅颈管Guide Bushing 引导衬套Guide Pin 导梢Guide Post 引导柱Guide Plate 导板Guide Rail 导轨Head Punch 顶头冲孔Headless Punch 直柄冲头Heavily Tapered Solid 整体模蕊盒Hose Nippler 管接头Impact Damper 缓冲器Injection Ram 压射柱塞Inlay Bush 嵌入衬套Inner Plunger 内柱塞Inner Punch 内冲头Insert 嵌件Insert Pin 嵌件梢King Pin 转向梢King Pin Bush 主梢衬套Knockout Bar 脱模杵Land 合模平坦面Land Area 合模面Leader Bush 导梢衬套Lifting Pin 起模顶针起模杆Lining 内衬Locating Center Punch 定位中心冲头Locating Pilot Pin 定位导梢Locating Ring 定位环Lock Block 压块Locking Block 定位块Locking Plate 定位板Loose Bush 活动衬套Making Die 打印冲子Manifold Block 歧管档块Master Plate 靠模样板Match Plate 分型板Mold Base 塑胶模座Mold Clamp 铸模紧固夹Mold Platen 模用板Moving Bolster 换模保持装置Moving Bolster Plate 可动侧模板One Piece Casting 整体铸件Parallel Block 平行垫块Parting Line 分模线Parting Lock Set 合模定位器Pass Guide 穴型导板Peened Head Punch 镶入式冲头锤击强化冲头钻杆凸模Pilot Pin 定位销导向销子Pin Gate 针尖浇口Plate 衬板Pre Extrusion Punch 顶挤冲头Punch 冲头Puncher 推杆Pusher Pin 衬套梢Rack 机架Rapping Rod 起模杆Re-entrant Mold 凹入模Retainer Pin 嵌件梢Retainer Plate 托料板Return Pin 回位梢Riding Stripper 浮动脱模器Ring Gate 环型浇口Roller 滚筒Runner 流道Runner Ejector Set 流道顶出器Runner Lock Pin 流道拉梢Screw Plug 头塞Set Screw 固定螺丝Shedder 脱模装置Shim 分隔片Shoe 模座之上下模板Shoot 流道Shoulder Bolt 肩部螺丝Skeleton 骨架Slag Riser 冒渣口Slide（Slide Core）滑块Slip Joint 滑配接头Spacer Block 间隔块Spacer Ring 间隔环Spider 模蕊支架Spindle 主轴Sprue 注道Sprue Bushing 注道衬套Sprue Bushing Guide 注道导套Sprue Lock Bushing 注道定位衬套Sprue Puller 注道拉料浇道推出杆注道残料顶销Spew Line 合模线Square Key 方键Square Nut 方螺帽Square Thread 方螺纹Limit Stop Collar 限位套Stop Pin 止动梢Stop Ring 止动环Stopper 定位停止梢Straight Pin 圆柱销Stripper Bolt 脱料螺栓Stripper Bushing 脱模衬套Stripper Plate 剥料板Stroke End Block 行程止梢Submarine Gate 潜入式浇口Support Pillar 支撑支柱顶出支柱Support Pin 支撑梢Supporting Plate 托板Sweep Template 造模刮板Tab Gate 辅助浇口Taper Key 推拔键Taper Pin 拔锥梢锥形梢Teeming Pouring 浇注Three Start Screw 三条螺纹Thrust Pin 推力销Tie Bar 拉杵Tunnel Gate 隧道形浇口Vent 通气孔Wortle Plate 拉丝模板模具术语翻译动模 Movable Mould Moving Half定模座板 Fixed Clamp Plate Top Clamping Plate Top Plate动模座板 Moving Clamp Plate Bottom Clamping Plate Bottom Plate上模座板 Upper Clamping Plate下模座板 Lower Clamping Plate凹模固定板 Cavity-retainer Plate型芯固定板 Mould Core-retainer Plate凸模固定板 Punch-retainer Plate模套 Die Body Die Sleeve Die Blank支承板 Backing Plate Support Plate垫块 Spacer Parallel支架 Ejector Housing Mould Base Leg模头 Die Head根据国家标准，以下为部分压铸模具标准翻译。
模具专业术语英语
模具专业术语英语
模具专业涉及许多专业术语，在英语中对应的词汇如下：
1. Mold/Mould: 模具
2. Die: 模具，尤指金属冲压模
3. Cavity: 模穴
4. Core: 模芯
5. Runner: 喷嘴，注塑道
6. Gate: 浇口，进料口
7. Ejector Pin: 顶针，用于将制品从模具中推出
8. Injection Molding: 注塑成型
9. Blow Molding: 吹塑
10. Compression Molding: 压缩成型
11. Extrusion Molding: 挤出成型
12. Casting: 铸造
13. Hot Runner: 热流道系统
14. Cooling Channel: 冷却通道
15. Draft Angle: 脱模锥度
16. Shrinkage: 收缩率
17. Surface Finish: 表面处理/光洁度
18. Undercut: 模具槽，模具凹槽
这些词汇在模具制造和加工过程中经常使用，涵盖了模具设计、制造和加工等方面的专业术语。
最全模具行业术语英文翻译
hole for screw
行位槽：
slide scot/scot for slide
喷砂：
engraving
螺母：
Nuts screw:
螺杆
导套：
guide bushing
try out:
试模
配镶件
making inserts
装配：
assemble
晒纹：
texturing
运水孔：
hole for water line
弹簧复位
manifold
热流道板
draft
斜度
热唧嘴hot runner
Inserted
镶件模
行位（滑块）：
slide
镶件：
insert
推板：
stripper plate
斜顶：
lifter
undercut倒扣/里面
Driller
钻床
flash披风
rib骨位一.
模具加工方法英语词汇四.
模具线切割放电加工相关英语词汇
顶料销
锁模块：
lock plate
斜顶：
lifters
Miller Milling Machine
铣床
快速接头：
jiffy quick connector plug/socker
Dowel Pin
定位梢
turnnel
隧道进浇
镶针
insert pin
排气槽: scot for venting
胶位: plastic
ball catch
喉塞: pipe plug
流道平衡:runner balance
斜顶杆：
angle ejector rod
模具专业英文术语大全
模具专业英文术语大全模具英语专业术语模具述语一、入水：gate进入位：gate locati on水口形式：gate type 大水口：edge gate 纟田水口：pin-point gate水口大小：gate size 转水口：s witchi ng runn er/gate唧嘴口径：sprue diameter二、流道：runner热流道：hot runn er,hot mani fold热嘴冷流道:hot sprue/cold runner 唧嘴直流:direct sprue gate 圆形流道：rou nd （full/half ru nner 流道电脑分析：mold flow an alysis流道平衡：runner balanee 热嘴：hot sprue 热流道板：hot man ifold 发热管：cartridge heater 探针:thermocouples 插头：conn ector plug 插座：conn ector socket 密封/封料：seal三、运水：water line 喉塞：line lpug 喉管：tube塑胶管：plastic tube 快速接头：jiffy quick conn ector plug/socker四、模具零件：mold comp onents 三板模：3-plate mold二板模：2-plate mold 边钉/ 导边：leader pin/guide pin 边司/ 导套：bushi ng/guide bush ing 中托司：shoulder guide bush ing 中托边L: guide pin 顶针板：ejector retainner plate 托板：support plate 螺丝：screw 管钉：dowel pin开模槽：ply bar scot 内模管位：core/cavity in ter-lock 顶针：ejector pin 司筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate 缩呵：movable core,return core core puller 扣机（尼龙拉勾）：n ylon latch lock斜顶：lifter 模胚（架）：mold base 上内模：cavity in sert 下内模：core insert 行位（滑块）：slide 镶件：in sert 压座/斜鸡：wedge 而寸磨板/油板：wedge wear plate 压条：plate 撑头:support pillar 唧嘴：sprue bush ing 挡板：stop plate 定位圈：locati ng ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B 顶板：eracuretu n 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spri ng rod 弹弓:die spring 中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞:pipe plug锁模块：lock plate 斜顶：an gle from pin 斜顶杆：an gle ejector rod 尼龙拉勾：part ing locks 活动臂：lever arm 复位键、提前回杆：early return bar气阀：valves 斜导边：an gle pin 术语：terms承压平面平衡：part ing surface supportbala nee模排气：part ing line ven ti ng回针碰料位：retur n pin and cavityin terfere nee模总高超岀啤机规格：mold base shuthight顶针碰运水：water line in terfereswithejector pin料位岀上/下模：part from cavith (core) side 模胚原身岀料位：cavity direct cut on A- plate,core direct cut on B-plate.不准用镶件：Do n ot use (core/cavity)in sert用铍铜做镶件：use beryllium copperin sert初步(正式)模图设计：preliinary (final) mold desig n反呵：reverse core弹弓压缩量：spri ng compressed len gth稳定性好：good stability,stable 强度不够：in sufficie nt rigidity 均匀冷去卩：eve n cooli ng 扣模：stick ing 热膨胀：thero expa nsion 公差：tolora nee 铜公(电极)：copper electrode Mold & die comp onents 模具单元Mold cha nging systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair模具维修Molds模具Press ing dies 压模Quick die cha nge systems 速换模系统Quick mold cha nge systems 快速换模系统三、模具塑料模具mould of plastics 注塑模具injection mould 冲压模具die 模架mould base定模座板Top clamping plateTop plateFixed clamp plate 水口推板stripper plate A 板 A plateB 板B plate 支承板support plate 方铁spacer plate 底针板ejector plate 面针板ejector retainer plate 回针Retur n pin 导柱Guide pin有托导套Shoulder Guide bush 直导套Straight Guide bush 动模座板Bottom clamp plate Mov ing clamp plate 基准线datum line 基准面datum plan 型芯固定板core-retainer plate 凸模固定板punch-retainer plate 顶针ejector pin单腔模具single cavity mould 多腔模具multi-cavity mould 多浇口multi-gating 浇口gate 缺料starving 排气breathing 光泽gloss 合模力mould clamping force 锁模力mould locking force 挤岀extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道sprue分流道runner浇口gate直浇口direct gate , sprue gate 轮辐浇口spoke gate , spider gate 点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线(面)parti ng line定模stationary mould ，Fixed mould 动模movable mould, movable half 上模upper mould ，upper half 下模lower mould ，lower half 型腔cavity凹模cavity plate ，cavity block拼块split定位销dowel定位销孑L dowel hole型芯core斜销an gle pin, fin ger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core 螺纹型芯threaded core热流道模具hot-ru nner mould 绝热流道模insulated runner mould 熔合纹weld line (flow line ) 三板式模具three plate mould 脱模ejection换模腔模具interchangeable cavity mould 脱模剂release age nt 注射能力shot capacity 注射速率injection rate 注射压力injection pressure 差色剂colorant 保压时间holdup time 闭模时间closing time 定型装置sizing system 阴模female mould , cavity block 阳模male mould电加工设备Electro n Discharge Machi ning 数控加工中心CNC machi ne cen ter 万能铁床Universal milling machine 卧式刨床Horizontal planer 车床Engine lathe 平面磨床Surface grinding machine 去磁机Demagnetization machine 万能摇臂钻床Uni versal radial movable driller 立式钻床Vertical driller 超声波清洗机Ultras onic cleari ng machi ne compre sio n moldi ng 压缩成型flash mold溢流式模具plsitive mold 挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak 仿皮革shiver饰纹flow mark 流痕weldi ng mark 溶合痕post screw in sert 螺纹套筒埋值self tapp ing screw 自攻螺丝striper plate 脱料板piston活塞cylinder汽缸套chip细碎物han dle mold 手持式模具（移转成型用模具）en capsulati on moldi ng 低压圭寸装成型（射岀成型用模具）two plate两极式（模具）well type 蓄料井in sulated runner 绝缘浇道方式hot runner 热浇道runner plat浇道模块valve gate 阀门浇口band heater环带状的电热器spindle 阀针spear head 刨尖头slag well冷料井cold slag冷料渣air vent排气道weldi ng line 熔合痕eject pin 顶岀针knock pin顶岀销return pin 回位销反顶针sleave 套筒stripper plate 脱料板insert core 放置入子runner stripper plate 浇道脱料板guide pin 导销eject rod （bar）（成型机）顶业捧subzero深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orie ntati on 定向sprue gate 射料浇口，直浇口nozzle射嘴sprue lock pin 料头钩销（拉料杆） slag well 冷料井side gate 侧浇口edge gate侧缘浇口tab gate搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate 隔膜浇口ring gate环形浇口subari ne gate 潜入式浇口tu nnel gate 隧道式浇口pin gate针点浇口Runner less 无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口；溶渣emboss 凸点dome 凸圆semi-sheari ng 半剪stamp mark 冲记号deburr or coin 压毛边punch riveti ng 冲压铆合side stretch 侧冲压平reel stretch 卷圆压平groove 压线blanking 下料stamp letter 冲字(料号) shearing 剪断tick-mark n earside 正面压印tick-mark farside 反面压印冲压名称类exte nsion dwg 展开图procedure dwg 工程图die structure dwg 模具结构图material 材质material thick ness 料片厚度factor系数upward 向上dow nward 向下upper plate 上模板lower plate 下模板die pad下垫板die holder 下夹板die set下模座bottomblock 下垫脚bottom plate下托板（底板）strippingplate 内外打（脱料板） outer stripper 夕卜脱料板inner stripper 内脱料板lower stripper 下脱料板零件类punch冲头insert入块（嵌入件）deburri ng punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller滚轴baffle plate 挡块located block 定位块support ing block for locati on定位支承块air cushi on plate 气垫板air-cushi on eject-rod 气垫顶杆trim ming punch 切边冲子stiffe ning rib punch = st in ger 力廿强筋冲子ribb on punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板slidi ng block 滑块塑料模具专业术语动模movable mould movi ng half 定模座板fixed clamp plate, top clampi ng plate. top plate动模座板movi ng clamp plate. bottom clampi ng plate. bottom plate上模座板upper clamp ing plate下模座板lower clampi ng plate 凹模固定板cavity-reta inerplate型芯固定板core-reta iner plate凸模固定板pun ch-reta iner plate模套chase. bolster. frame支承板back ing plate. supprr plate垫块spacer parallel支架ejector hous ing. mould base leg 压力铸造模具die-casti ng diepress specificati on 冲床规格die height range 适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guid ing post 内导柱inner hexago n screw 内六角螺钉dowel pin 固定销coil spring 弹簧lifter pin顶料销eq-height sleeves=spool 等高套筒pin销lifter guide pin 浮升导料销guide pin 导正销wire spri ng 圆线弹簧outer guid ing post 夕卜导柱stop screw 止付螺丝located pin 定位销outer bush 夕卜导套模板类top plate上托板（顶板）top block上垫脚punch set 上模座punch pad 上垫板punch holder 上夹板stripper pad脱料背板up stripper 上脱料板male die 公模（凸模） feature die 公母模female die 母模（凹模）。
模具专业英文术语大全
模具英语专业术语模具述语一、入水:gate进入位: gate location水口形式:gate type大水口:edge gate细水口: pinpoint gate水口大小:gate size转水口: switching runner/gate唧嘴口径: sprue diameter二、流道: runner热流道: hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道:round(full/half runner流道电脑分析:mold flow analysis流道平衡:runner balance热嘴: hot sprue热流道板:hot manifold发热管:cartridge heater探针: thermocouples插头: connector plug插座: connector socket密封/封料: seal三、运水:water line喉塞:line lpug喉管:tube塑胶管:plastic tube快速接头:jiffy quick connector plug/socker 四、模具零件: mold ponents三板模:3plate mold二板模:2plate mold边钉/导边:leader pin/guide pin边司/导套:bushing/guide bushing中托司:shoulder guide bushing中托边L:guide pin顶针板:ejector retainner plate托板: support plate螺丝: screw管钉:dowel pin开模槽:ply bar scot内模管位:core/cavity interlock顶针: ejector pin司筒:ejector sleeve 司筒针:ejector pin推板:stripper plate缩呵:movable core,return core core puller 扣机(尼龙拉勾):nylon latch lock斜顶:lifter模胚(架): mold base上内模:cavity insert下内模:core insert行位(滑块): slide镶件:insert压座/斜鸡:wedge耐磨板/油板:wedge wear plate压条:plate撑头: support pillar唧嘴: sprue bushing挡板:stop plate定位圈:locating ring锁扣:latch扣鸡:parting lock set推杆:push bar栓打螺丝:S、H、S、B顶板:eracuretun活动臂:lever arm分流锥:spure sperader水口司:bush垃圾钉:stop pin隔片:buffle弹弓柱:spring rod弹弓:die spring中托司:ejector guide bush中托边:ejector guide pin镶针:pin销子:dowel pin波子弹弓:ball catch喉塞: pipe plug锁模块:lock plate斜顶:angle from pin斜顶杆:angle ejector rod尼龙拉勾:parting locks活动臂:lever arm复位键、提前回杆:early return bar气阀:valves斜导边:angle pin术语:terms承压平面平衡:parting surface support balance模排气:parting line venting回针碰料位:return pin and cavity interference模总高超出啤机规格:mold base shut hight 顶针碰运水:water line interferes withejector pin料位出上/下模:part from cavith (core) side 模胚原身出料位:cavity direct cut on Aplate,core direct cuton Bplate、不准用镶件: Do not use (core/cavity) insert 用铍铜做镶件: use beryllium copper insert 初步(正式)模图设计:preliinary (final) mold design反呵:reverse core弹弓压缩量:spring pressed length稳定性好:good stability,stable强度不够:insufficient rigidity均匀冷却:even cooling扣模:sticking热膨胀:thero expansion公差:tolorance铜公(电极):copper electrodeMold & die ponents 模具单元Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Pressing dies 压模Quick die change systems 速换模系统Quick mold change systems 快速换模系统三、模具塑料模具 mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plate Top plateFixed clamp plate水口推板stripper plateA 板A plateB 板B plate支承板 support plate方铁 spacer plate底针板 ejector plate面针板 ejector retainer plate 回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush 直导套 Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板coreretainer plate 凸模固定板punchretainer plate 顶针ejector pin单腔模具single cavity mould 多腔模具multicavity mould多浇口multigating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force 锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道 sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pinpoint gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴coldslug well浇口套sprue bush流道板runner plate排飞槽vent分型线(面)parting line定模stationary mould,Fixed mould动模movable mould, movable half上模upper mould, upper half下模lower mould, lower half型腔cavity凹模cavity plate,cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hotrunner mould绝热流道模insulated runner mould熔合纹weld line (flow line)三板式模具 three plate mould脱模ejection换模腔模具 interchangeable cavity mould 脱模剂release agent注射能力shot capacity注射速率injection rate 注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould,cavity block阳模male mould电加工设备Electron Discharge Machining 数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine pre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具(移转成型用模具)encapsulation molding 低压封装成型(射出成型用模具)two plate 两极式(模具)well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状得电热器spindle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道welding line 熔合痕eject pin 顶出针knock pin 顶出销return pin 回位销反顶针sleave 套筒stripper plate 脱料板insert core 放置入子runner stripper plate 浇道脱料板guide pin 导销eject rod (bar)(成型机)顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orientation 定向sprue gate 射料浇口,直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆) slag well 冷料井side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口subarine gate 潜入式浇口tunnel gate 隧道式浇口pin gate 针点浇口Runner less 无浇道(sprue less)无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣emboss 凸点dome 凸圆semishearing 半剪stamp mark 冲记号deburr or coin 压毛边punch riveting 冲压铆合side stretch 侧冲压平reel stretch 卷圆压平groove 压线blanking 下料stamp letter 冲字(料号) shearing 剪断tickmark nearside 正面压印tickmark farside 反面压印冲压名称类extension dwg 展开图procedure dwg 工程图die structure dwg 模具结构图material 材质material thickness 料片厚度factor 系数upward 向上downward 向下press specification 冲床规格die height range 适用模高die height 闭模高度burr 毛边gap 间隙weight 重量total wt、总重量punch wt、上模重量五金零件类inner guiding post 内导柱inner hexagon screw 内六角螺钉dowel pin 固定销coil spring 弹簧lifter pin 顶料销eqheight sleeves=spool 等高套筒pin 销lifter guide pin 浮升导料销guide pin 导正销wire spring 圆线弹簧outer guiding post 外导柱stop screw 止付螺丝located pin 定位销outer bush 外导套模板类top plate 上托板(顶板)top block 上垫脚punch set 上模座punch pad 上垫板punch holder 上夹板stripper pad 脱料背板up stripper 上脱料板male die 公模(凸模)feature die 公母模female die 母模(凹模)upper plate 上模板lower plate 下模板die pad 下垫板die holder 下夹板die set 下模座bottom block 下垫脚bottom plate 下托板(底板)stripping plate 内外打(脱料板)outer stripper 外脱料板inner stripper 内脱料板lower stripper 下脱料板零件类punch 冲头insert 入块(嵌入件)deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller 滚轴baffle plate 挡块located block 定位块supporting block for location定位支承块air cushion plate 气垫板aircushion ejectrod 气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子reelstretch punch 卷圆压平冲子guide plate 定位板sliding block 滑块塑料模具专业术语动模 movable mould moving half定模座板 fixed clamp plate, top clamping plate、 top plate动模座板 moving clamp plate、 bottom clamping plate、 bottom plate上模座板 upper clamping plate下模座板 lower clamping plate凹模固定板 cavityretainer plate型芯固定板 coreretainer plate凸模固定板 punchretainer plate模套 chase、 bolster、 frame 支承板 backing plate、 supprr plate 垫块 spacer parallel支架 ejector housing、 mould base leg 压力铸造模具 diecasting die压铸模零部件定模 fixed die, cover die定模座板 fixed clamping plate定模套板 bolstor, fixed die动模 moving die,ejector die动模座板 moving clamping plate直流道 sprue横流道 runner内浇口 gatelanded plunger mold||有肩柱塞式模具burnishing die||挤光模landed positive mold||有肩全压式模具button die||镶入式圆形凹模loading shoe mold||料套式模具centergated mold||中心浇口式模具loose detail mold||活零件模具chill mold||冷硬用铸模loose mold||活动式模具clod hobbing||冷挤压制模louvering die||百叶窗冲切模posite dies||复合模具manifold die||分歧管模具counter punch||反凸模modular mold||组合式模具double stack mold||双层模具multicavity mold||多模穴模具electroformed mold||电铸成形模multigate mold||复式浇口模具expander die||扩径模offswt bending die||双折冷弯模具extrusion die||挤出模palletizing die||叠层模family mold||反套制品模具plaster mold||石膏模blank through dies||漏件式落料模porous mold||通气性模具duplicated cavity plate||复板模positive mold||全压式模具fantail die||扇尾形模具pressure die||压紧模fishtail die||鱼尾形模具pro轮廓模flash mold||溢料式模具progressive die||顺序模gypsum mold||石膏铸模protable mold||手提式模具hotrunner mold||热流道模具prototype mold||雏形试验模具ingot mold||钢锭模punching die||落料模lancing die||切口模raising(embossing)||压花起伏成形reentrant mold||倒角式模具sectional die||拼合模runless injection mold||无流道冷料模具sectional die||对合模具segment mold||组合模semipositive mold||半全压式模具shaper||定型模套single cavity mold||单腔模具solid forging die||整体锻模split forging die||拼合锻模split mold||双并式模具sprueless mold||无注道残料模具squeezing die||挤压模stretch form die||拉伸成形模sweeping mold||平刮铸模swing die||振动模具three plates mold||三片式模具trimming die||切边模unit mold||单元式模具universal mold||通用模具unscrewing mold||退扣式模具yoke type die||轭型模模具钢材 khuôn thépalloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 矽钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑胶覆面钢板塑件与模具pre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具(移转成型用模具)encapsulation molding低压封装成型(射出成型用模具)two plate两极式(模具)well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状得电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)(成型机)顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口,直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Runner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板aircushion ejectrod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reelstretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱springbox ejectrod弹簧箱顶杆springbox ejectplate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块模板类top plate上托板(顶板)top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semishearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tickmark nearside正面压印tickmark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt、总重量punch wt、上模重量连接器connector端子terminal条型连接器bar connector阴连接器Housing阳连接器wafer线束wire harness间距space额定电压 rated voltage额定电流 rated current接触电阻contact resistance 绝缘电阻insulation resistance 超声波焊接ultrasonic welding 耐压withstand voltage针pin物料编号part number导线wire基体金属Base metal电缆夹cable clamp倒角chamfer接触面积contact area接触件安装孔contact cavity 接触长度contact length 接触件电镀层contact plating接触压力contact pressure接触件中心距contact space接触簧片contact spring插孔socket contact法兰、凸缘Flange界面间隙interfacial gap键Key键槽keyway过渡段ramp屏蔽套shielding定位基准Datum reference扁平电缆flat cable ,Ribbon cable柔性印刷电线Flexible printed wiring 多层印制电路Multilayer printed circuit 焊盘pad图形pattern间距pitch负极Negative pole正极positive pole回流Reflow原理图Schematic diagram单面板single sided board双面板Twosided board,Doublesided board表面安装surface Mounting翘曲warp, bow波峰焊wave soldering编织层braid同轴电缆coaxial cable电介质dielectric电缆中导线得头数ends外部干扰external interference填充物filler护套jacket比重specific gravity电阻得温度系数Temperature coefficient of resistance模具塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板 support plate方铁 spacer plate底针板 ejector plate面针板 ejector retainer plate回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush直导套 Straight Guide bush动模座板Bottom clamp plateMoving clamp plate基准线datum line基准面datum plan型芯固定板coreretainer plate凸模固定板punchretainer plate顶针ejector pin 单腔模具single cavity mould多腔模具multicavity mould多浇口multigating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道 sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pinpoint gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴coldslug well浇口套sprue bush流道板runner plate排飞槽vent分型线(面)parting line定模stationary mould,Fixed mould动模movable mould, movable half上模upper mould, upper half下模lower mould, lower half型腔cavity凹模cavity plate,cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hotrunner mould绝热流道模insulated runner mould熔合纹weld line (flow line)三板式模具three plate mould脱模ejection换模腔模具 interchangeable cavity mould 脱模剂release agent注射能力shot capacity 注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould,cavity block阳模male mould电加工设备Electron Discharge Machining 数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine模具零件Top Plate 上托板(顶板)Top Block 上垫脚Punch Set 上模座Punch Pad 上垫板Punch Holder 上夹板Stripper Pad 脱料背板Up Stripper 上脱料板Male Die 公模(凸模)Feature Die 公母模Female Die 母模(凹模)Upper Mold Plate 上模板Lower Mold Plate 下模板Die Pad 下垫板Die Holder 下夹板Die Set 下模座Bottom Block 下垫脚Bottom Plate下托板(底板) Stripping Plate 内外打(脱料板) Outer Stripper 外脱料板Inner Stripper 内脱料板Lower Stripper 下脱料板Inner Guiding Post 内导柱Inner Hexagon Screw 内六角螺钉Dowel Pin 固定销Mould Coil Spring 模具弹簧Lifter Pin 顶料销Isoheight Sleeve 等高套筒Pin 销Lifter Guide Pin 浮升导料销Guide Pin 导正销Wire Spring 圆线弹簧Outer Guiding Post 外导柱Stop Screw 止付螺丝Located Pin 定位销Outer Bush 外导套Punch 冲头Insert 入块(嵌入件)Deburring Punch 压毛边冲子Groove Punch 压线冲子Stamped Punch 字模冲子Round Punch 圆冲子Special Shape Punch 异形冲子Bending Block 折刀Roller 滚轴Baffle Plate 挡块Located Block 定位块Supporting Block for Location 定位支承块Air Cushion Plate 气垫板AirCushion Ejectrod 气垫顶杆Trimming Punch 切边冲子Stiffening Rib Punch Stinger 加强筋冲子Ribbon Punch 压筋冲子Reelstretch Punch 卷圆压平冲子Guide Plate 定位板Sliding Block 滑块Sliding Dowel Block 滑块固定块Active Plate 活动板Lower Sliding Plate 下滑块板Upper Holder Block 上压块Upper Mid Plate 上中间板Spring Box 弹簧箱SpringBox Ejectrod 弹簧箱顶杆SpringBox EjectPlate 弹簧箱顶板Bushing Block Liner Bushing 衬套Cover Plate 盖板Guide Pad 导料块模具技术用语各种常用模具成形方式Accurate Die Casting 精密压铸Powder Forming 粉末成形Calendaring Molding 压延成形Powder Metal Forging 粉末锻造Cold Chamber Die Casting 冷式压铸Precision Forging 精密锻造Cold Forging 冷锻Press Forging 冲锻pacting Molding 粉末压出成形Rocking Die Forging 摇动锻造pound Molding 复合成形Rotary Forging 回转锻造pression Molding 压缩成形Rotational Molding 离心成形Dip Mold 浸渍成形Rubber Molding 橡胶成形Encapsulation Molding 注入成形Sand Mold Casting 砂模铸造Extrusion Molding 挤出成形Shell Casting 壳模铸造Foam Forming 发泡成形Sinter Forging 烧结锻造Forging Roll 轧锻Six Sides Forging 六面锻造Gravity Casting 重力铸造Slush Molding 凝塑成形Hollow Blow Molding 中空(吹出)成形Squeeze Casting 高压铸造Hot Chamber Die Casting 热室压铸Swaging 挤锻Hot Forging 热锻Transfer Molding 转送成形Injection Molding 射出成形Warm Forging 温锻Investment Casting 精密铸造Matched Die Method 对模成形法Laminating Method 被覆淋膜成形Low Pressure Casting 低压铸造Lost Wax Casting 脱蜡铸造Matched Mould Thermal Forming 对模热成形模Close Mold 合模Demould 脱模脱模剂Mould Unloading 开模Eject 顶出Tool Change Retooling Die Changing 换模Mould Clamping 锁模各式模具分类用语Bismuth Mold 铋铸模Landed Plunger Mold 有肩柱塞式模具Burnishing Die 挤光模Landed Positive Mold 有肩全压式模具Button Die 镶入式圆形凹模Loading Shoe Mold 料套式模具CenterGated Mold 中心浇口式模具Loose Detail Mold 活零件模具Chill Mold 冷硬用铸模Loose Mold 活动式模具Cold Hobbing 冷挤压制模法Louvering Die 百叶窗冲切模posite Dies 复合模具Manifold Die 分歧管模具Counter Punch 反凸模Modular Mold 组合模具Double Stack Mold 双层模具MultiCavity Mold 多模穴模具Electroformed Mold 电铸成形模MultiGate Mold 复式浇口模具Expander Die 扩径模Offset Cold Bending Die 双折冷弯模具Extrusion Die 挤出模Stack Mold, Stack Injection Mould 叠层模Family Mold 反套制品模具Plaster Mold 石膏模Blank Through Dies 漏件式落料模Porous Mold 通气性模具Duplicated Cavity Plate 复板模Positive Mold 全压式模具Fantail Die 扇尾形模具Pressure Die 压紧模Fishtail Die 鱼尾形模具Pro 轮廓模Flash Mold 溢料式模具Progressive Die 顺序模Gypsum Mold 石膏铸模Portable Mold 手提式模具HotRunner Mold 热流道模具Prototype Mold 雏形试验模具原型模具Ingot Mold 钢锭模Punching Die 落料模Lancing Die 切口模切缝模Raising(Embossing) 压花起伏成形Reentrant Mold 倒角式模具Sectional Die 拼合模Runless Injection Mold 无流道冷料模具Sectional Die 对合模具Segment Mold 组合模SemiPositive Mold 半全压式模具Shaper 定型模套Single Cavity Mold 单腔模具Solid Forging Die 整体锻模Split Forging Die 拼合锻模Split Mold 双并式模具Sprueless Mold 无注道残料模具Squeezing Die 挤压模Stretch Form Die 拉伸成形模Sweeping Mold 平刮铸模Swing Die 振动模具Three Plates Mold 三片式模具Trimming Die 切边模Unit Mold 单元式模具Universal Mold 通用模具Unscrewing Mold 退扣式模具Yoke Type Die 轭型模模具厂常用之标准零配件Air Vent Valve 通气阀Anchor Pin 锚梢Angular Pin 角梢Baffle 调节阻板Angular Pin 倾斜梢Baffle Plate 折流档板Ball Button 球塞套Ball Plunger 定位球塞Ball Slider 球塞滑块Binder Plate 压板Blank Holder 防皱压板Blanking Die 落料冲头Bolster 上下模板Bottom board 浇注底板Bolster 垫板Bottom Plate 下固定板Bracket 托架Bumper Block 缓冲块Buster 堵口Casting Ladle 浇注包Casting lug 铸耳Cavity 模穴(模仁)Cavity Retainer Plate 模穴托板Center Pin 中心梢Clamping Block 锁定块Coil Spring 螺旋弹簧Cold Punched Nut 冷冲螺母Cooling Spiral 螺旋冷却栓Core 心型Core Pin 心型梢Cotter 开口梢Cross 十字接头Cushion Pin 缓冲梢Diaphragm Gate 盘形浇口Die Approach 模头料道Die Bed 型底Die Block 块形模体Die Body 铸模座Die Bush 合模衬套Die Button 冲模母模Die Clamper 夹模器Die Fastener 模具固定用零件Die Holder 母模固定板Die Lip 模唇Die Plate 冲模板Die Set 冲压模座Direct Gate 直接浇口Dog Chuck 爪牙夹头Dowel 定位梢Dowel Hole 导套孔Dowel Pin 合模梢Dozzle 辅助浇口Dowel Pin 定位梢Draft 拔模锥度Draw Bead 张力调整杆Drive Bearing 传动轴承Ejection Pad 顶出衬垫Ejector 脱模器Ejector Guide Pin 顶出导梢Ejector Leader Bush 顶出导梢衬套Ejector Pad 顶出垫Ejector Pin 顶出梢Ejector Plate 顶出板Ejector Rod 顶出杆Ejector Sleeve 顶出衬套Ejector Valve 顶出阀Eye Bolt 环首螺栓Filling Core 填充型芯椿入蕊Film Gate 薄膜形浇口Finger Pin 指形梢Finish Machined Plate 角形模板Finish Machined Round Plate 圆形模板Fixed Bolster Plate 固定侧模板Flanged Pin 带凸缘针Flash Gate 毛边形浇口Flask 上箱Floating Punch 浮动冲头Gate 浇口Gate Land 浇口面Gib 凹形拉紧楔Goose Neck 鹅颈管Guide Bushing 引导衬套Guide Pin 导梢Guide Post 引导柱Guide Plate 导板Guide Rail 导轨Head Punch 顶头冲孔Headless Punch 直柄冲头Heavily Tapered Solid 整体模蕊盒Hose Nippler 管接头Impact Damper 缓冲器Injection Ram 压射柱塞Inlay Bush 嵌入衬套Inner Plunger 内柱塞Inner Punch 内冲头Insert 嵌件Insert Pin 嵌件梢King Pin 转向梢King Pin Bush 主梢衬套Knockout Bar 脱模杵Land 合模平坦面Land Area 合模面Leader Bush 导梢衬套Lifting Pin 起模顶针起模杆Lining 内衬Locating Center Punch 定位中心冲头Locating Pilot Pin 定位导梢Locating Ring 定位环Lock Block 压块Locking Block 定位块Locking Plate 定位板Loose Bush 活动衬套Making Die 打印冲子Manifold Block 歧管档块Master Plate 靠模样板Match Plate 分型板Mold Base 塑胶模座Mold Clamp 铸模紧固夹Mold Platen 模用板Moving Bolster 换模保持装置Moving Bolster Plate 可动侧模板One Piece Casting 整体铸件Parallel Block 平行垫块Parting Line 分模线Parting Lock Set 合模定位器Pass Guide 穴型导板Peened Head Punch 镶入式冲头锤击强化冲头钻杆凸模Pilot Pin 定位销导向销子Pin Gate 针尖浇口Plate 衬板Pre Extrusion Punch 顶挤冲头Punch 冲头Puncher 推杆Pusher Pin 衬套梢Rack 机架Rapping Rod 起模杆Reentrant Mold 凹入模Retainer Pin 嵌件梢Retainer Plate 托料板Return Pin 回位梢Riding Stripper 浮动脱模器Ring Gate 环型浇口Roller 滚筒Runner 流道Runner Ejector Set 流道顶出器Runner Lock Pin 流道拉梢Screw Plug 头塞Set Screw 固定螺丝Shedder 脱模装置Shim 分隔片Shoe 模座之上下模板Shoot 流道Shoulder Bolt 肩部螺丝Skeleton 骨架Slag Riser 冒渣口Slide(Slide Core) 滑块Slip Joint 滑配接头Spacer Block 间隔块Spacer Ring 间隔环Spider 模蕊支架Spindle 主轴Sprue 注道Sprue Bushing 注道衬套Sprue Bushing Guide 注道导套Sprue Lock Bushing 注道定位衬套Sprue Puller 注道拉料浇道推出杆注道残料顶销Spew Line 合模线Square Key 方键Square Nut 方螺帽Square Thread 方螺纹Limit Stop Collar 限位套Stop Pin 止动梢Stop Ring 止动环Stopper 定位停止梢Straight Pin 圆柱销Stripper Bolt 脱料螺栓Stripper Bushing 脱模衬套Stripper Plate 剥料板Stroke End Block 行程止梢Submarine Gate 潜入式浇口Support Pillar 支撑支柱顶出支柱Support Pin 支撑梢Supporting Plate 托板Sweep Template 造模刮板Tab Gate 辅助浇口Taper Key 推拔键Taper Pin 拔锥梢锥形梢Teeming Pouring 浇注Three Start Screw 三条螺纹Thrust Pin 推力销Tie Bar 拉杵Tunnel Gate 隧道形浇口Vent 通气孔Wortle Plate 拉丝模板模具术语翻译动模 Movable Mould Moving Half定模座板 Fixed Clamp Plate Top Clamping Plate Top Plate动模座板 Moving Clamp Plate Bottom Clamping Plate Bottom Plate上模座板 Upper Clamping Plate下模座板 Lower Clamping Plate凹模固定板 Cavityretainer Plate型芯固定板 Mould Coreretainer Plate凸模固定板 Punchretainer Plate模套 Die Body Die Sleeve Die Blank支承板 Backing Plate Support Plate垫块 Spacer Parallel支架 Ejector Housing Mould Base Leg模头 Die Head根据国家标准,以下为部分压铸模具标准翻译。
模具术语中英文对照
模具术语中英文对照模具(Mold) - A shaped cavity or matrix into which molten or uncured material is poured so thatupon solidification it will take on the shape of the cavity.注射模(Injection mold) - A molding cavity created by injecting material into a mold via a runner system.常用于塑料件注塑。
压铸模(Die casting mold) - A metal mold created for die casting processes, usually zinc, copper or aluminum based alloys.充型范(Pattern) - A full sized model of the desired casting, used to create the mold cavity in processes like sand casting.冒口(Sprue) - The primary vertical channel through which liquid material is poured into mold cavities.冒口通过主要供料道向模板腔内引入熔融金属。
气孔(Vent) - A small channel allowing the gases formed (by vaporization,chemical reaction etc.) to escape from mold cavity.用来排出模具腔内气体的小通道。
流道(Gate) - The channel that conveys molten metal from the sprue into the mold cavity.将熔融金属从主流道(冒口)引入模腔的小槽道。
模具基本术语英汉对照
各种模具常用成形方式accurate die casting 精密压铸 powder forming 粉末成形calendaring molding 压延成形 powder metal forging 粉末锻造cold chamber die casting 冷式压铸 precision forging 精密锻造cold forging 冷锻 press forging 冲锻compacting molding 粉末压出成形 rocking die forging 摇动锻造compound molding 复合成形 rotary forging 回转锻造compression molding 压缩成形 rotational molding 离心成形dip mold 浸渍成形 rubber molding 橡胶成形encapsulation molding 注入成形 sand mold casting 砂模铸造extrusion molding 挤出成形 shell casting 壳模铸造foam forming 发泡成形 sinter forging 烧结锻造forging roll 轧锻 six sides forging 六面锻造gravity casting 重力铸造 slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形 squeeze casting 高压铸造hot chamber die casting 热室压铸 swaging 挤锻hot forging 热锻 transfer molding 转送成形injection molding 射出成形 warm forging 温锻investment casting 精密铸造 matched die method 对模成形法laminating method 被覆淋膜成形 low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模常用模具英语die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die 连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销模具术语中英文对照，全面、精选第一期：组装、冲压、喷漆等专业词汇Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条形码barcode scanner条形码扫描仪fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造技术cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs.inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis |'∫æsi| 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS电源电压接柆键sheet metal parts 冲件plastic parts塑料件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork*车personnel resource department 人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |'plein |刨床miller铣床grinder磨床driller钻床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager |'depjuti| =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dei★n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embeded lump|in'bed| |l mp|镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift*车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓name of a department部门名称administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift*车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头sweeper扫把mop拖把vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机production line流水线chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程die repair模修enterprise plan = enterprise expansion projects企划QC品管die worker模工production, to produce生产equipment设备to start a press开机stop/switch off a press关机classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-grade products良品defective products, not up-to-grade products不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱die change 换模to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---to throw--over switching over切换engineering, project difficulty工程瓶颈stage die工程模automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊vocabulary for stamping冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to. to send delinery back to retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑common vocabulary for die engineering模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder活页夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physical invetory second count 复盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accounting department for reference会计部存查end-user/using unit(department)使用单位summary of year-end physical inventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条形码flow chart流程窗体assembly组装stamping冲压molding成型spare parts=buffer备品coordinate坐标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕疪shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧。
模具专业英文术语大全
模具英语专业术语模具述语顶针：ejector pin司筒：一、入水：gate ejector sleeve司筒针：ejector pin 进入位：gate location推板：stripper plate水口形式：gate type缩呵：edge gate movable core,return core core 大水口：pullerpin-point gate 细水口：扣机（尼龙拉勾）：nylon latch lock gate size水口大小：斜顶：lifterswitching runner/gate 转水口：模胚（架）：mold base sprue diameter 唧嘴口径：上内模：cavity insert : runner二、流道下内模：core insert hot runner,hot manifold 热流道：行位（滑块）：slide : hot sprue/cold runner 热嘴冷流道镶件：insert : direct sprue gate 唧嘴直流压座/斜鸡：wedgeround(full/half runner 圆形流道：耐磨板/油板：wedge wear plate mold flow analysis 流道电脑分析：压条：plate :runner balance 流道平衡撑头: support pillar hot sprue 热嘴：唧嘴：sprue bushing hot manifold 热流道板：挡板：stop plate cartridge heater 发热管：定位圈：locating ring : thermocouples 探针锁扣：latchconnector plug 插头：扣鸡：parting lock set connector socket 插座：推杆：push bar seal 密封封料：/栓打螺丝：S.H.S.B water line 三、运水：顶板：eracuretun line lpug 喉塞：活动臂：lever arm tube喉管：分流锥：spure sperader plastic tube塑胶管：水口司:bush jiffy quick connector 快速接头：垃圾钉：stop pin plug/socker隔片：四、模具零件：mold components buffle弹弓柱：spring rod 三板模：3-plate mold弹弓:die spring二板模：2-plate mold中托司：导边：/边钉leader pin/guide pin ejector guide bush中托边：bushing/guide bushing ejector guide pin 导套：/边司镶针：pin shoulder guide bushing 中托司：销子：guide pin：中托边Ldowel pin波子弹弓：顶针板：ejector retainner plate ball catch喉塞托板：support plate : pipe plug锁模块：lock plate screw 螺丝：斜顶：dowel pin 管钉：angle from pin斜顶杆：开模槽：ply bar scotangle ejector rodparting locks尼龙拉勾：core/cavity inter-lock内模管位：活动臂：lever armQuick mold change systems 快速换模系统三、模具early return bar 复位键、提前回杆：塑料模具气阀：valves mould of plastics注塑模具斜导边：angle pin injection mould冲压模具die 术语：terms模架mould base承压平面平衡：parting surface supportbalance定模座板Top clamping plate parting line venting模排气：Top plateFixed clamp platereturn pin and cavity 回针碰料位：水口推板stripper plate interferencemold base shut 模总高超出啤机规格：A 板A platehightB 板B plate water line interferes 顶针碰运水：支承板support plate withejector pin方铁spacer plate part from cavith (core) 料位出上/下模：底针板ejector plate side面针板ejector retainer plate cavity direct cut on A-模胚原身出料位：plate,core direct cut 回针Return pin on B-plate.导柱Guide pinDo not use (core/cavity) 不准用镶件：有托导套Shoulder Guide bush insert直导套Straight Guide bush use beryllium copper 用铍铜做镶件：insert动模座板Bottom clamp plate preliinary (final) 初步（正式）模图设计：Moving clamp platemold design基准线datum line reverse core反呵：基准面datum planspring compressed length 弹弓压缩量：型芯固定板core-retainer plate good stability,stable 稳定性好：凸模固定板punch-retainer plate insufficient rigidity 强度不够：顶针ejector pineven cooling 均匀冷却：单腔模具single cavity mould sticking扣模：多腔模具multi-cavity mould thero expansion 热膨胀：多浇口multi-gating tolorance公差：浇口gate copper electrode (电极）：铜公缺料starving模具单元Mold & die components 排气breathing换模系统Mold changing systems 光泽glossMold core 模芯合模力mould clamping force冷却器模具加热器Mold heaters/chillers /锁模力mould locking forceMold polishing/texturing 模具打磨/磨纹挤出extrusionMold repair 模具维修开裂crack模具Molds 循环时间cycle timePressing dies 压模老化agingQuick die change systems 速换模系统screw螺杆．麻点pit 熔合纹weld line （flow line）三板式模具insertthree plate mould 嵌件脱模活动镶件movable insert ejection换模腔模具interchangeable cavity mould 起垩chalking脱模剂release agent 浇注系统feed system注射能力sprue shot capacity 主流道注射速率分流道runner injection rate注射压力浇口gateinjection pressure差色剂colorant 直浇口direct gate , sprue gate保压时间holdup time 轮辐浇口spoke gate , spider gate闭模时间pin-point gate closing time 点浇口定型装置sizing system测浇口edge gate阴模female mould，潜伏浇口submarine gate , tunnel gate cavity block阳模料穴cold-slug well male mould电加工设备Electron Discharge Machining 浇口套sprue bush数控加工中心流道板runner plate CNC machine center万能铁床Universal milling machine 排飞槽vent卧式刨床parting lineHorizontal planer 分型线（面）车床定模stationary mouldEngine lathe，Fixed mould平面磨床movable mould, movable half Surface grinding machine 动模去磁机Demagnetization machine ，upper half 上模upper mould万能摇臂钻床下模lower mouldUniversal radial movable ，lower halfdrillercavity型腔立式钻床Vertical drillercavity block cavity plate，凹模超声波清洗机Ultrasonic clearing machine split 拼块compre sion molding 压缩成型dowel 定位销flash mold 溢流式模具dowel hole 定位销孔plsitive mold 挤压式模具core型芯split mold 分割式模具angle pin, finger cam 斜销cavity 型控母模slide滑块core 模心公模slide guide strip 滑块导板taper 锥拔heel block, wedge lock 楔紧块leather cloak 仿皮革sprue puller 拉料杆shiver 饰纹locating ring 定位环flow mark 流痕cooling channel 冷却通welding mark 溶合痕draft 脱模斜度post screw insert 螺纹套筒埋值slide core 滑动型芯self tapping screw 自攻螺丝threaded core 螺纹型芯striper plate 脱料板hot-runner mould 热流道模具piston 活塞insulated runner mould绝热流道模汽缸套cylinderchip 细碎物flash gate 闸门浇口slit gate 手持式模具缝隙浇口handle mold（移转成型用模具）fan gate 扇形浇口dish gate 因盘形浇口encapsulation molding 低压封装成型（射出成型用模具）diaphragm gate 隔膜浇口ring gate 环形浇口two plate 两极式（模具）subarine gate 潜入式浇口well type 蓄料井tunnel gate 隧道式浇口insulated runner 绝缘浇道方式pin gate 针点浇口hot runner 热浇道Runner less runner plat 无浇道浇道模块(sprue less)无射料管方式valve gate 阀门浇口long nozzle 延长喷嘴方式band heater 环带状的电热器sprue 浇口;spindle 阀针溶渣emboss 凸点刨尖头spear headdome 凸圆slag well 冷料井semi-shearing 半剪cold slag 冷料渣stamp mark 冲记号排气道air ventdeburr or coin 熔合痕welding line 压毛边punch riveting 冲压铆合eject pin 顶出针side stretch 侧冲压平顶出销knock pinreel stretch return pin 回位销反顶针卷圆压平groove 压线套筒sleaveblanking 下料stripper plate 脱料板stamp letter 冲字(料号) 放置入子insert coreshearing 剪断runner stripper plate 浇道脱料板tick-mark nearside 正面压印导销guide pintick-mark farside eject rod (bar)（成型机）顶业捧反面压印冲压名称类深冷处理subzeroextension dwg 三极式模具three plate 展开图procedure dwg 工程图浇道系统runner systemdie structure dwg 模具结构图stress crack 应力电裂定向orientation material 材质sprue gate 射料浇口，直浇口料片厚度material thickness射嘴nozzle 系数factorsprue lock pin 料头钩销向上) 拉料杆(upward冷料井slag well downward 向下side gate 侧浇口冲床规格press specification适用模高die height range 侧缘浇口edge gate搭接浇口tab gate 闭模高度die height毛边burr 薄膜浇口film gategap 间隙die pad 下垫板die holder 下夹板weight 重量die set 下模座total wt.总重量bottom block 下垫脚punch wt.上模重量五金零件类bottom plate 下托板(底板)stripping plate inner guiding post 内导柱内外打(脱料板)outer stripper 外脱料板inner hexagon screw 内六角螺钉inner stripper 内脱料板dowel pin 固定销lower stripper coil spring 弹簧下脱料板零件类顶料销lifter pinpunch 冲头eq-height sleeves=spool 等高套筒insert 入块(嵌入件销pin )deburring punch 压毛边冲子lifter guide pin 浮升导料销groove punch 压线冲子guide pin 导正销stamped punch 字模冲子wire spring 圆线弹簧round punch 圆冲子外导柱outer guiding postspecial shape punch 异形冲子stop screw 止付螺丝bending block 折刀located pin 定位销roller 滚轴outer bush 外导套模板类baffle plate 挡块located block 定位块top plate 上托板（顶板）supporting block for location 上垫脚top block 定位支承块punch set 上模座air cushion plate 气垫板上垫板punch padair-cushion eject-rod 气垫顶杆punch holder 上夹板trimming punch 切边冲子stripper pad 脱料背板stiffening rib punch = stinger 加强筋冲子up stripper 上脱料板ribbon punch 压筋冲子) (male die 公模凸模reel-stretch punch 卷圆压平冲子feature die 公母模guide plate 定位板) (female die 母模凹模sliding block 滑块上模板upper plate下模板lower plate塑料模具专业术语动模movable mould moving half 下模座板lower clamping plate凹模固定板cavity-retainer plate 定模座板fixed clamp plate, topclamping plate. top plate 型芯固定板core-retainer plate moving clamp plate. bottom 动模座板凸模固定板punch-retainer plate clamping plate. bottom platechase. bolster. frame 模套upper clamping plate 上模座板支承板backing plate. supprr plate duplicated cavity plate||复板模spacer parallel 垫块positive mold||全压式模具ejector housing. mould base leg 支架fantail die||扇尾形模具压力铸造模具die-casting die pressure die||压紧模压铸模零部件fishtail die||鱼尾形模具定模fixed die, cover die profile die||轮廓模fixed clamping plate 定模座板flash mold||溢料式模具定模套板bolstor, fixed die progressive die||顺序模moving die,ejector die 动模gypsum mold||石膏铸模动模座板moving clamping plate protable mold||手提式模具直流道sprue hot-runner mold||热流道模具runner 横流道prototype mold||雏形试验模具gate 内浇口ingot mold||钢锭模punching die||落料模有肩柱塞式模具landed plunger mold||lancing die||切口模burnishing die||挤光模raising(embossing)||压花起伏成形有肩全压式模具landed positive mold||re-entrant mold||倒角式模具button die||镶入式圆形凹模sectional die||拼合模loading shoe mold||料套式模具runless injection mold||无流道冷料模具center-gated mold||中心浇口式模具对合模具sectional die|| loose detail mold||活零件模具segment mold||组合模冷硬用铸模chill mold|| semi-positive mold||半全压式模具loose mold||活动式模具shaper||定型模套冷挤压制模clod hobbing|| single cavity mold||单腔模具louvering die||百叶窗冲切模solid forging die||整体锻模composite dies||复合模具拼合锻模split forging die|| manifold die||分歧管模具双并式模具split mold|| counter punch||反凸模无注道残料模具sprueless mold|| 组合式模具modular mold|| 挤压模squeezing die|| double stack mold||双层模具拉伸成形模stretch form die|| 多模穴模具multi-cavity mold|| 平刮铸模sweeping mold|| 电铸成形模electroformed mold|| swing die||振动模具multi-gate mold||复式浇口模具three plates mold||三片式模具expander die||扩径模切边模trimming die|| 双折冷弯模具offswt bending die|| 单元式模具unit mold|| 挤出模extrusion die|| 通用模具universal mold|| palletizing die||叠层模unscrewing mold||退扣式模具family mold||反套制品模具轭型模yoke type die|| 石膏模plaster mold||p én th模具钢材khu? 漏件式落料模blank through dies|| 合金工具钢alloy tool steel 通气性模具porous mold||aluminium alloy 铝合金钢leather cloak仿皮革shiver轴承合金饰纹bearing alloyflow mark流痕blister steel 浸碳钢welding mark溶合痕bonderized steel sheet 邦德防蚀钢板post screw insert螺纹套筒埋值carbon tool steel 碳素工具钢self tapping screw自攻螺丝clad sheet 被覆板striper plate脱料板clod work die steel 冷锻模用钢piston活塞emery 金钢砂cylinder汽缸套钢铁水静压力ferrostatic pressurechip细碎物forging die steel 锻造模用钢handle mold手持式模具galvanized steel sheet 镀锌铁板（移转成型用模具）超硬合金钢hard alloy steelencapsulation molding低压封装成型高速度工具钢high speed tool steel（射出成型用模具）hot work die steel 热锻模用钢两极式（模具）two platelow alloy tool steel 特殊工具钢蓄料井well typelow manganese casting steel 低锰铸钢绝缘浇道方式马式体高强度热处理钢marging steel insulated runner 热浇道hot runner martrix alloy 马特里斯合金浇道模块runner platmeehanite cast iron 米汉纳铸钢valve gatemeehanite metal 米汉纳铁阀门浇口band heater环带状的电热器市售钢材merchant iron 阀针molybdenum high speed steel 钼系高速钢spindle molybdenum steel 钼钢刨尖头spear head 镍铬钢nickel chromium steel 冷料井slag well 冷料渣prehardened steel 顶硬钢cold slag air vent排气道矽钢板silicon steel sheet不锈钢welding line熔合痕stainless steeltin plated steel sheet eject pin镀锡铁板顶出针韧铜knock pin顶出销tough pitch copper troostite return pin吐粒散铁回位销反顶针tungsten steel 钨钢套筒sleave vinyl tapped steel sheet 脱料板stripper plate塑胶覆面钢板放置入子insert core 塑件与模具runner stripper plate浇道脱料板compre sion molding压缩成型guide pin导销flash mold溢流式模具（成型机）顶业捧eject rod (bar) 挤压式模具plsitive mold 深冷处理subzero 分割式模具split mold three plate三极式模具cavity母模型控浇道系统runner system 模心core公模应力电裂stress crack 锥拔taper orientation定向stiffening rib punch = stinger 加强筋冲子ribbon punch射料浇口，直浇口压筋冲子sprue gatereel-stretch punch卷圆压平冲子nozzle射嘴guide plate定位板(拉料杆) sprue lock pin料头钩销sliding block滑块slag well冷料井sliding dowel block滑块固定块侧浇口side gateactive plate活动板edge gate侧缘浇口lower sliding plate下滑块板tab gate搭接浇口upper holder block上压块film gate薄膜浇口upper mid plate上中间板flash gate闸门浇口spring box弹簧箱slit gate缝隙浇口spring-box eject-rod弹簧箱顶杆fan gate扇形浇口spring-box eject-plate弹簧箱顶板dish gate因盘形浇口bushing bolck 衬套隔膜浇口diaphragm gatecover platering gate环形浇口盖板guide pad 导料块subarine gate潜入式浇口隧道式浇口tunnel gate模板类针点浇口pin gatetop plate上托板（顶板）Runner less无浇道top block上垫脚(sprue less)无射料管方式punch set 上模座long nozzle延长喷嘴方式punch pad上垫板;溶渣浇口spruepunch holder上夹板零件类stripper pad脱料背板up stripper 上脱料板冲头punchmale die公模(凸模(insert入块嵌入件))feature die公母模压毛边冲子deburring punchfemale die母模groove punch压线冲子(凹模)upper plate字模冲子stamped punch 上模板lower plate圆冲子round punch下模板die pad异形冲子special shape punch 下垫板die holderbending block折刀下夹板die setroller下模座滚轴bottom block下垫脚挡块baffle platebottom plate下托板定位块located block(底板)supporting block for location stripping plate内外打(脱料板) 定位支承块outer stripper外脱料板气垫板air cushion plateinner stripper内脱料板air-cushion eject-rod气垫顶杆下脱料板lower stripper trimming punch切边冲子plain die简易模stamp letter冲字(料号)shearing剪断pierce die冲孔模tick-mark nearside正面压印成型模forming dietick-mark farside反面压印progressive die连续模冲压名称类gang dies复合模extension dwg展开图shearing die剪边模procedure dwg工程图铆合模riveting diedie structure dwg pierce冲孔模具结构图material材质成型(抽凸,冲凸) formingmaterial thickness料片厚度抽孔draw holefactor折弯bending 系数upward向上trim切边downward向下凸点embosspress specificationdome凸圆冲床规格die height range适用模高半剪semi-shearingdie height闭模高度stamp mark冲记号burr 毛边deburr or coin压毛边gap 冲压铆合间隙punch rivetingweightside stretch重量侧冲压平total wt.reel stretch卷圆压平总重量punch wt.压线groove 上模重量下料blanking倒角chamfer 连接器connector接触面积contact area 端子terminal接触件安装孔bar connector contact cavity 条型连接器接触长度contact length 阴连接器Housing接触件电镀层阳连接器contact plating wafer接触压力线束wire harness contact pressure接触件中心距contact space 间距space接触簧片contact spring 额定电压rated voltage插孔socket contact rated current 额定电流法兰、凸缘contact resistance Flange 接触电阻界面间隙insulation resistance 绝缘电阻interfacial gap键ultrasonic welding Key 超声波焊接键槽withstand voltage 耐压keyway过渡段ramp pin针屏蔽套shieldingpart number 物料编号定位基准Datum reference 导线wire扁平电缆Base metal 基体金属flat cable ，Ribbon cableFlexible printed wiring柔性印刷电线cable clamp电缆夹．多层印制电路Multilayer printed circuit 直导套Straight Guide bush动模座板焊盘pad Bottom clamp plateMoving clamp plate pattern 图形基准线datum line pitch间距基准面datum planNegative pole 负极型芯固定板core-retainer plate positive pole 正极凸模固定板punch-retainer plate Reflow回流顶针ejector pinSchematic diagram 原理图单腔模具single cavity mould single sided board单面板多腔模具multi-cavity mould Double-sided ，双面板Two-sided board多浇口multi-gating board 浇口surface Mounting 表面安装gate缺料，bow starving 翘曲warp排气波峰焊wave soldering breathing光泽glossbraid编织层合模力mould clamping force 同轴电缆coaxial cable锁模力mould locking force dielectric 电介质挤出extrusion 电缆中导线的头数ends开裂external interference 外部干扰crack循环时间cycle time filler 填充物老化jacket 护套aging螺杆比重specific gravityscrew麻点pit Temperature coefficient of 电阻的温度系数resistance 嵌件insert模具活动镶件movable insert mould of plastics 塑料模具起垩chalking injection mould 注塑模具浇注系统feed system die 冲压模具主流道sprue mould base模架分流道runner Top clamping plate 定模座板浇口gateTop plate直浇口direct gate , sprue gate Fixed clamp plate轮辐浇口spoke gate , spider gate stripper plate 水口推板点浇口pin-point gate A plate A板测浇口edge gateB plate B板潜伏浇口submarine gate , tunnel gate support plate 支承板料穴cold-slug well spacer plate 方铁浇口套sprue bush ejector plate 底针板流道板runner plate ejector retainer plate 面针板排飞槽ventReturn pin 回针分型线（面）parting lineGuide pin导柱Fixed mould，stationary mould定模Shoulder Guide bush有托导套．动模movable mould, movable half 脱模ejection换模腔模具interchangeable cavity mould upper mould，upper half 上模脱模剂lower half release agent 下模lower mould，注射能力型腔cavityshot capacity注射速率，cavity block injection rate cavity plate凹模注射压力injection pressure 拼块split差色剂dowel colorant 定位销保压时间定位销孔dowel hole holdup time闭模时间型芯coreclosing time定型装置sizing system斜销angle pin, finger cam阴模female mould，滑块slidecavity block阳模滑块导板slide guide strip male mould电加工设备楔紧块heel block, wedge lock Electron Discharge Machining数控加工中心sprue puller 拉料杆CNC machine center万能铁床Universal milling machine 定位环locating ring卧式刨床cooling channel 冷却通Horizontal planer车床Engine lathe脱模斜度draft平面磨床Surface grinding machine slide core 滑动型芯去磁机threaded core Demagnetization machine 螺纹型芯万能摇臂钻床热流道模具Universal radial movable hot-runner moulddrillerinsulated runner mould 绝热流道模立式钻床Vertical drillerflow line）weld line 熔合纹（超声波清洗机Ultrasonic clearing machinethree plate mould 三板式模具模具零件Bottom Plate下托板（底板）Stripping Plate 内外打（脱料板）上托板（顶板）Top PlateOuter Stripper 外脱料板T op Block 上垫脚Inner Stripper 内脱料板上模座Punch SetLower Stripper 下脱料板Punch Pad 上垫板Inner Guiding Post 内导柱上夹板Punch Holder Inner Hexagon Screw 内六角螺钉Stripper Pad 脱料背板Dowel Pin 固定销上脱料板Up Stripper Mould Coil Spring Male Die 公模（凸模）模具弹簧Lifter Pin 公母模Feature Die 顶料销Isoheight Sleeve 等高套筒Female Die 母模（凹模）Pin 上模板Upper Mold Plate 销Lifter Guide Pin Lower Mold Plate 浮升导料销下模板Guide Pin 下垫板Die Pad 导正销Wire Spring 圆线弹簧Die Holder 下夹板Outer Guiding Post 外导柱下模座Die Set止付螺丝Stop Screw 下垫脚Bottom BlockLocated Pin 定位销Compacting Molding 粉末压出成形Rocking Die Forging 外导套Outer Bush 摇动锻造Compound Molding 复合成形Punch 冲头Rotary Forging 回转锻造Insert 入块（嵌入件）Compression Molding 压缩成形Deburring Punch 压毛边冲子Rotational Molding Groove Punch 压线冲子离心成形Dip Mold 字模冲子浸渍成形Stamped PunchRubber Molding Round Punch 圆冲子橡胶成形Encapsulation Molding 注入成形Special Shape Punch 异形冲子Sand Mold Casting 砂模铸造折刀Bending BlockExtrusion Molding 挤出成形Roller 滚轴Shell Casting 壳模铸造Baffle Plate 挡块Foam Forming 发泡成形Located Block 定位块Sinter Forging 烧结锻造定位支承块Supporting Block for LocationForging Roll Air Cushion Plate 气垫板轧锻Six Sides Forging 六面锻造Air-Cushion Eject-rod 气垫顶杆Gravity Casting 切边冲子重力铸造Trimming PunchSlush Molding 加强筋冲子Stiffening Rib Punch Stinger 凝塑成形Hollow Blow Molding 中空（吹出）成形Ribbon Punch 压筋冲子Squeeze Casting 高压铸造Reel-stretch Punch 卷圆压平冲子Hot Chamber Die Casting 热室压铸Guide Plate 定位板Swaging 挤锻滑块Sliding BlockHot Forging Sliding Dowel Block 滑块固定块热锻Transfer Molding 转送成形活动板Active PlateInjection Molding 射出成形Lower Sliding Plate 下滑块板Warm Forging 温锻上压块Upper Holder BlockInvestment Casting Upper Mid Plate 上中间板精密铸造Matched Die Method 对模成形法弹簧箱Spring BoxLaminating Method 被覆淋膜成形Spring-Box Eject-rod 弹簧箱顶杆Low Pressure Casting 低压铸造弹簧箱顶板Spring-Box Eject-PlateLost Wax Casting 衬套脱蜡铸造Bushing Block Liner BushingMatched Mould Thermal Forming Cover Plate 对模热成形模盖板Guide Pad 导料块合模Close Mold脱模剂脱模Demould 模具技术用语Mould Unloading 开模各种常用模具成形方式Eject 顶出Accurate Die Casting 精密压铸换模Tool Change Retooling Die ChangingPowder Forming 粉末成形锁模Mould Clamping压延成形Calendaring Molding各式模具分类用语Powder Metal Forging 粉末锻造铋铸模Bismuth Mold 冷式压铸Cold Chamber Die Casting精密锻造Precision Forging 有肩柱塞式模具Landed Plunger Mold冷锻Cold Forging 挤光模Burnishing Die有肩全压式模具Landed Positive Mold 冲锻Press ForgingButton Die 镶入式圆形凹模Segment Mold 组合模Semi-Positive Mold 半全压式模具Loading Shoe Mold 料套式模具Shaper 定型模套Center-Gated Mold 中心浇口式模具Single Cavity Mold 单腔模具Loose Detail Mold 活零件模具Solid Forging Die 整体锻模Chill Mold 冷硬用铸模Split Forging Die Loose Mold 活动式模具拼合锻模Split Mold Cold Hobbing 冷挤压制模法双并式模具Sprueless Mold 无注道残料模具Louvering Die 百叶窗冲切模Squeezing Die 挤压模Composite Dies 复合模具Stretch Form Die 拉伸成形模分歧管模具Manifold DieSweeping Mold 平刮铸模Counter Punch 反凸模Swing Die 振动模具Modular Mold 组合模具Three Plates Mold 三片式模具Double Stack Mold 双层模具Trimming Die 切边模Multi-Cavity Mold 多模穴模具Unit Mold Electroformed Mold 电铸成形模单元式模具Universal Mold 通用模具Multi-Gate Mold 复式浇口模具Unscrewing Mold 退扣式模具Expander Die 扩径模Yoke Type Die 轭型模双折冷弯模具Offset Cold Bending Die挤出模Extrusion Die 模具厂常用之标准零配件叠层模Stack Mold, Stack Injection Mould通气阀Air Vent Valve Family Mold 反套制品模具锚梢Anchor Pin Plaster Mold 石膏模角梢Angular Pin 漏件式落料模Blank Through DiesBaffle 调节阻板Porous Mold 通气性模具Angular Pin 倾斜梢Duplicated Cavity Plate 复板模Baffle Plate 折流档板Positive Mold 全压式模具Ball Button 球塞套扇尾形模具Fantail DieBall Plunger 定位球塞Pressure Die 压紧模球塞滑块Ball Slider 鱼尾形模具Fishtail Die压板Binder Plate Profile Die 轮廓模防皱压板Blank Holder Flash Mold 溢料式模具落料冲头Blanking Die 顺序模Progressive Die上下模板Bolster 石膏铸模Gypsum Mold浇注底板Bottom board Portable Mold 手提式模具Bolster 垫板Hot-Runner Mold 热流道模具Bottom Plate 下固定板Prototype Mold 雏形试验模具原型模具托架Bracket 钢锭模Ingot Mold缓冲块Bumper Block 落料模Punching Die堵口Buster 切缝模切口模Lancing DieCasting Ladle 浇注包（Raising ）压花起伏成形Embossing 铸耳Casting lug 倒角式模具Re-entrant Mold模穴（模仁）Cavity 拼合模Sectional Die模穴托板Cavity Retainer Plate Runless Injection Mold 无流道冷料模具中心梢Center Pin 对合模具Sectional DieClamping Block 锁定块Film Gate 薄膜形浇口Finger Pin 指形梢Coil Spring 螺旋弹簧Finish Machined Plate 角形模板Cold Punched Nut 冷冲螺母Finish Machined Round Plate 圆形模板Cooling Spiral 螺旋冷却栓Fixed Bolster Plate 固定侧模板Core 心型Flanged Pin Core Pin 心型梢带凸缘针Flash Gate 开口梢Cotter 毛边形浇口Flask 上箱Cross 十字接头Floating Punch 浮动冲头Cushion Pin 缓冲梢Gate 浇口Diaphragm Gate 盘形浇口Gate Land 浇口面Die Approach 模头料道Gib 凹形拉紧楔Die Bed 型底Goose Neck 鹅颈管Die Block 块形模体Guide Bushing 引导衬套Die Body 铸模座Guide Pin Die Bush 导梢合模衬套Guide Post 引导柱Die Button 冲模母模Guide Plate 导板Die Clamper 夹模器Guide Rail 导轨Die Fastener 模具固定用零件Head Punch 顶头冲孔母模固定板Die HolderHeadless Punch Die Lip 模唇直柄冲头Heavily Tapered Solid 整体模蕊盒冲模板Die PlateHose Nippler 管接头Die Set 冲压模座Impact Damper 缓冲器直接浇口Direct GateInjection Ram 爪牙夹头压射柱塞Dog ChuckInlay Bush Dowel 定位梢嵌入衬套Inner Plunger 内柱塞Dowel Hole 导套孔Inner Punch 内冲头合模梢Dowel PinInsert 嵌件Dozzle 辅助浇口Insert Pin 定位梢Dowel Pin 嵌件梢King Pin 转向梢Draft 拔模锥度King Pin Bush 主梢衬套张力调整杆Draw BeadKnockout Bar 脱模杵Drive Bearing 传动轴承Land 合模平坦面顶出衬垫Ejection PadLand Area 脱模器Ejector 合模面Leader Bush Ejector Guide Pin 导梢衬套顶出导梢Lifting Pin 起模顶针起模杆Ejector Leader Bush 顶出导梢衬套Lining 内衬顶出垫Ejector PadLocating Center Punch 定位中心冲头顶出梢Ejector PinLocating Pilot Pin 顶出板Ejector Plate 定位导梢Locating Ring Ejector Rod 顶出杆定位环Lock Block Ejector Sleeve 压块顶出衬套Locking Block Ejector Valve 定位块顶出阀Locking Plate 定位板环首螺栓Eye Bolt活动衬套Loose Bush 椿入蕊填充型芯Filling CoreMaking Die 打印冲子Slide（Slide Core）滑块Slip Joint 滑配接头Manifold Block 歧管档块Spacer Block 间隔块Master Plate 靠模样板Spacer Ring 间隔环Match Plate 分型板Spider Mold Base 塑胶模座模蕊支架Spindle 铸模紧固夹主轴Mold ClampSprue 注道Mold Platen 模用板Sprue Bushing 注道衬套Moving Bolster 换模保持装置Sprue Bushing Guide 注道导套Moving Bolster Plate 可动侧模板Sprue Lock Bushing 注道定位衬套One Piece Casting 整体铸件Sprue Puller 注道拉料平行垫块Parallel Block 浇道推出杆注道残料顶销Spew Line 合模线Parting Line 分模线Square Key 方键Parting Lock Set 合模定位器Square Nut 方螺帽Pass Guide 穴型导板Square Thread 方螺纹镶入式冲头Peened Head Punch 锤击强化冲头钻杆凸模限位套Limit Stop Collar止动梢Stop Pin 导向销子定位销Pilot PinPin Gate 针尖浇口止动环Stop Ring定位停止梢Stopper Plate 衬板圆柱销Straight Pin Pre Extrusion Punch 顶挤冲头脱料螺栓冲头Punch Stripper Bolt推杆脱模衬套Stripper Bushing PuncherPusher Pin 衬套梢Stripper Plate 剥料板Stroke End Block Rack 机架行程止梢Submarine Gate 潜入式浇口起模杆Rapping RodRe-entrant Mold 凹入模顶出支柱Support Pillar 支撑支柱Retainer Pin Support Pin 支撑梢嵌件梢Retainer Plate 托料板托板Supporting Plate造模刮板回位梢Return Pin Sweep Template辅助浇口Tab Gate Riding Stripper 浮动脱模器推拔键Taper Key 环型浇口Ring Gate拔锥梢锥形梢滚筒Roller Taper PinTeeming Pouring 浇注流道RunnerThree Start Screw 三条螺纹Runner Ejector Set 流道顶出器推力销Thrust Pin 流道拉梢Runner Lock Pin拉杵Tie Bar 头塞Screw Plug隧道形浇口Tunnel Gate 固定螺丝Set ScrewVent 脱模装置Shedder 通气孔拉丝模板分隔片Shim Wortle Plate模座之上下模板Shoe 模具术语翻译Shoot 流道Movable Mould Moving Half动模Shoulder Bolt 肩部螺丝Fixed Clamp Plate Top Clamping Plate 定模座板Skeleton 骨架Top Plate冒渣口Slag Riser动模座板Moving Clamp Plate Bottom Clamping Extrusion Mold 挤压式模具Plate Bottom PlateSplit Mold 分割式模具Upper Clamping Plate 上模座板Mould Cavity 型腔母模Lower Clamping Plate 下模座板Mold Core 模芯公模Cavity-retainer Plate 凹模固定板Large Die Mold 大型模具Mould Core-retainer Plate 型芯固定板Precise Die Mold 精密模具Punch-retainer Plate 凸模固定板Complex Die Mold 复杂模具Die Body Die Sleeve Die Blank 模套Foaming Mould 发泡模具Backing Plate Support Plate 支承板Metal Die 金属模具Spacer Parallel垫块Plastic Mold 塑料模具Ejector Housing Mould Base Leg支架Press Tool Stamping Die Punch Die 冲压模具Die Head 模头Extrusion Die 挤压模具石墨模具Graphite Die 根据国家标准，以下为部分压铸模具标准翻译。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
主题：模具常用英语单词一、入水：gate 缩呵：movablecore,return core core puller 进入位：gate location 扣机（尼龙拉勾）：nylon latch lock 水口形式：gate type 上内模：cavity insert 下内模：core insert 大水口：edge gate 压座/ 斜鸡：wedge 活动臂：lever arm 细水口：pin-point gate 耐磨板/ 油板：wedge wear plate 水口大小：gate size 压条：plate 撑头: support pillar 转水口：switching runner/gate 扣鸡：parting lock set 推杆：push bar 唧嘴口径：sprue diameter 栓打螺丝：S.H.S.B 顶板：eracuretun 二、流道: runner 分流锥：spure sperader 热流道：hot runner,hot manifold 隔片：buffle 弹弓柱：spring rod 热嘴冷流道: hot sprue/cold runner 弹弓:die spring 中托司：ejector guide bush 唧嘴直流: direct sprue gate 中托边：ejector guide pin 圆形流道：round （full/half runner 镶针：pin 销子：dowel pin 流道电脑分析：mold flow analysis 波子弹弓：ball catch 喉塞: pipe plug 流道平衡:runner balance 斜顶杆：angle ejector rod 热流道板：hot manifold 尼龙拉勾：parting locks活动臂：lever arm 发热管：cartridge heater 复位键、提前回杆：early return bar 探针: thermocouples 气阀：valves 斜导边：angle pin 插头：connector plug 承压平面平衡：parting surface support balance 插座：connector socket 回针碰料位：return pin and cavity interference 密封/ 封料：seal 模总高超出啤机规格：mold base shut hight 三、运水：water line 顶针碰运水：water line interferes withejector pin 喉塞：line lpug 料位出上/ 下模：part from cavith (core) side 喉管：tube 模胚原身出料位：cavity direct cut on A-plate, 塑胶管：plastic tube 不准用镶件：Do not use (core/cavity) insert 四、模具零件：mold components 用铍铜做镶件：use beryllium copper insert 三板模：3-plate mold 初步(正式)模图设计：preliinary (final) mold design 二板模：2-plate mold 反呵：reverse core 边钉/ 导边：leader pin/guide pin 弹弓压缩量：spring compressed length 中托司：shoulder guide bushing 稳定性好：good stability,stable 中托边Lguide pin 强度不够：insufficient rigidity 托板：support plate 均匀冷却：even cooling 管钉：dowel pin 扣模：sticking 公差：tolorance 开模槽：ply bar scot 热膨胀：thero expansion 内模管位：core/cavity inter-lock铜公(engraving 螺母：电极)：Nuts screw:copper electrode 螺杆司筒：导套：ejector sleeve guide bushing模排气：try out:parting line venting 试模司筒针：配镶件ejector pin making inserts core direct cut on B-plate. 装配：热嘴：assemblehot sprue 晒纹：Moulding texturing模塑运水孔：水口司hole for water line:bush 限位开关：垃圾钉：Limit Switchesstop pin 直顶：Lifter Pin top顶料销engraving:锁模块：晒字lock plate 喷砂：斜顶：texturelifters 吹塑Miller Milling Machine :blowmolding铣床guide pin :快速接头：导柱jiffy quick connector plug/socker solidDowel Pin 整板模定位梢cold sprueturnnel 冷唧嘴隧道进浇, cold runner镶针hydraulic ejectioninsert pin 油缸顶出排气槽cashew: scot for venting 腰果型进浇胶位spring return: plastic 弹簧复位牙孔：manifoldhole for screw 热流道板行位槽：draftslide scot/scot for slide 斜度喷砂：热唧嘴hot runnerInserted 镶件模行位（滑块）：slide 镶件：insert 推板：stripper plate 斜顶：lifter undercut 倒扣/ 里面Driller 钻床flash 披风rib 骨位模具加工方法英语词汇四模具线切割放电加工相关英语词汇abnormal glow 不规则辉光放电barrel 滚筒（加工）arc discharge 电弧放电bending 波纹加工belt 皮带broaching 拉刀切削centreless 无心centering 定中心chrome bronze 铭铜cutting 切削clearance angle 後角cylindrical lathe cutting 外圆车削corner shear drop 直角压陷electric discharge machine 放电加工deflection 桡曲度electrolytic grinding 电解研磨discharge energy 放电能量embossing 压花加工dressing 修整facing 面车削dwell 保压filing 锉刀修润flange 凸缘hand finishing 手工修润gap 间隙hemming 卷边加工graphite 石墨hobbing 滚齿加工graphite contraction allowance 电极缩小余量joggling 摇动加工graphite holder 电极夹座lapping 抛光skiving 表面研磨 slotting 切缝切削 sharp edge 锐角部 taper turning 锥度车削 tough bronze 韧铜 thread cutting 螺纹切削 traverse 摇臂 ultrasonic machining 超音波加工 tungsten bronze 钨青铜 up cut milling 逆铣加工 waviness 波形起伏 working allowance 加工余量 模具砂轮用语英语词汇 working dischard 加工废料 abrasive 砂轮 Al2O3 氧化铝 五 模具冲压机械及周边英语词汇 borazon氧化硼立方晶 back shaft 支撑轴 buffing wheel 抛光布轮 blank determination 胚料展开/ 研磨修润 hair crack 发裂 laser beam machining 雷射加工 horn 电极臂 lathe cutting 车床车削 jump 跳刀 planning 刨削加工 magnetic base 磁性座 polishing 抛亮光 master graphite 标准电极 reaming 铰孔修润 pipe graphite 管状电极 rough machining 粗切削pulse脉冲rounding 圆形加工 rib working 肋部加工 sawing 锯削 roller electrode 滚轮式电极 scaling 清除钢碇缺陷 rotary surface 旋转面 shaping 成形加工 shank 柄部型 砂 轮 slitting 切缝量 clutch 离合器 vitrified 陶瓷的 clutch brake 离合器制动器 clutch boss 离合器轮壳模具锻铸造相关英语词汇 clutch lining 离合器覆盖 accretion 炉瘤 coil car 带卷升降运输机 acid converter 酸性转炉 coil cradle 卷材进料装置 acid lining cupola 酸性熔铁炉 coil reel stand 钢材卷料架 acid open-hearth furnace 酸性平炉 column 圆柱 aerator 松砂机 connection screw 连杆调节螺钉 air set mold 常温自硬铸模 core compound 砂心黏结剂 airless blasting cleaning 离心喷光diamond 钻石 bottom slide press 下传动式压力机 dresser 砂轮整修机 board drop hammer 板落锤 dressing 修整 brake 煞车 buckle 剥砂面 endless grinding belt 循环式研磨带 camlachie cramp 铸包 finishing allowance 加工余量 chamotte sand 烧磨砂 grain 磨粒 charging hopper 加料漏斗 grinding disc 研磨盘 clearance 间隙 jamp up 孔眼堵塞 closed-die forging 合模锻造 mesh 网筛目 clump 夹紧 resinoid grinding wheel 半 树 脂counter blow hammer 对击锻锤all core molding 集合式铸模cradle 送料架all round die holder 通用模座crank 曲柄轴assembly mark 铸造合模记号crankless 无曲柄式back pouring 补浇注cross crank 横向曲轴backing sand 背砂cushion 缓冲base bullion 粗金属锭depression 外缩凹孔base permeability 原砂透气度dial feed 分度送料belling 压凸die approach 模口角度billet 坏料die assembly 合模bleed 漏铸die cushion 模具缓冲垫blocker 预锻模膛die height 冲压闭合高度blocking 粗胚锻件die life 模具寿命blow hole 铸件气孔die opening 母模逃孔board drop hammer 板落锤die spotting press 调整冲模用压力机bottom pour mold 底浇double crank press 双曲柄轴冲床bottom pouring 底注draght angle 逃料倾斜角boxless mold 脱箱砂模edging 边锻伸break-off core 缩颈砂心embedded core 加装砂心brick molding 砌箱造模法feed length 送料长度buckle 剥砂面feed level 送料高度camber 错箱filling core 埋入砂心camlachie cramp 铸包friction brake 摩擦煞车 counter blow hammer 对击锻造 gap shear 凹口剪床 counter lock 止口镶嵌方式 gear 齿轮 depression 外缩凹孔 gib 滑块引导部 die approach 模口角度 gripper 夹具 draw out 锻造拔长 gripper feed 夹持进料 draw plate 起模板 gripper feeder 夹紧传送装置 draw spike 起模长针 hammer 槌机 dummying 预锻 hand press 手动冲床 embedded core 加装砂心 hand rack pinion press 手动齿轮齿条式冲床 erosion 冲砂 hand screw press 手动螺旋式冲床 fettling 铸件清理filling in 填砂 cast blade 铸造叶片 film play 液面花纹 casting flange 铸造凸缘 fine blanking press 精密下料冲床 casting on flat 水平铸造 forging roll 辊锻机 chamotte sand 烧磨砂 finishing slag 炼後熔渣 charging hopper 加料漏斗 fly wheel 飞轮 cleaning of casting 铸件清理 fly wheel brake 飞轮制动器 closed-die forging 合模锻造 foot press 脚踏冲床 core compound 砂心黏结剂 formboard 进模口板 core template 砂心模板 frame 床身机架 core vent 砂蕊排气孔 friction 摩擦 corner gate 压边浇口hopper feed 料斗送料heading machine 顶镦机filling core micro inching device埋入砂心微寸动装置idle stage impacter空站卧式锻造机filling in microinching equipment 填砂微动装置inching inblock cast微调尺寸整体铸造film play moving bolster液面花纹活动工作台isothermal forging ingot恒温锻造铸锭finishing slag notching press炼後熔渣冲缺口压力机key clutch ingot blank键槽离合器铸坯flash gutter opening锻模飞边槽排料逃孔knockout inlay casting脱模装置镶铸法flask molding overload protection device 砂箱造模防超载装置knuckle mechanic investment casting转向机构失模铸造forging roll pinch roll辊锻机导正滚轮land isothermal forging模具直线刀面部恒温锻造formboard pinion进模口板小齿轮loader loose piece供料器木模活块unloader pitch卸料机节距gutter molding pit锻模飞边槽铸模地坑loop controller pressfit闭回路控制器压入hammer man pouring process锻工浇注法lower die progressive下模连续送料recasting sieve mesh重铸筛孔pusher feed roller leveler推杆式送料辊式矫直机roll forging sintering of sand 轧锻铸砂烧贴pusher feeder rotary bender料片押片装置卷弯成形机rolled surface slag轧制表面熔渣quick die change system safety guard快速换模系统安全保护装置rough sand slag inclusion粗砂夹渣regrinding scrap cutter再次研磨废料切刀roughing forge stickness粗锻黏模性releasing scrap press松释动作废料冲床sand crushing strip layout塌箱带状胚料排样法reversed blanking seamless forging 反转下料无缝锻造seamless forging tap casting无缝锻造顶注robot shave机器人崩砂separate top gate分离顶注浇口roll forming machine shear angle辊轧成形剪角shave unworked casting 崩砂不加工铸件roll forming machine sheet loader辊轧成形机薄板装料机shrinkage fit upender收缩配合翻转装置roll release shot脱辊单行程工作shut height upending闭合高度顶锻roller feed shrinkage fit辊式送料收缩配合uphill casting 拉伸矫直机底铸compressingshut height 压缩加工闭合高度strip feederwhite cast iron 料材送料装置白口铸件compression bendingsieve mesh 押弯曲加工筛孔stripping pressure六弹出压力crowning模具冲模加工英语词汇凸面加工sintering of sand stroke铸砂烧贴冲程barreling curl bending滚光加工卷边弯曲加工slide balancer take out device滑动平衡器取料装置belling curling压凸加工卷曲加工slug hole toggle press逃料孔肘杆式压力机bending cutting弯曲加工切削加工spin forming machine transfer feed旋压成形机连续自动送料装置blanking dinking下料加工切断蕊骨spotting turrent punch press 合模转塔冲床bulging double shearing撑压加工叠板裁断stack feeder two speed clutch堆叠拨送料机双速离合器burring drawing冲缘加工引伸加工stickness uncoiler黏模性闭卷送料机cam die bending drawing with ironing 凸轮弯曲加工抽引光滑加工straight side frame unloader冲床侧板卸载机coining embossing压印加工浮花压制加工stretcher leveler vibration feeder振动送料机extrusion 挤制加工wiring press 嵌线卷边机filing 锉削加工七模具常用刀具工作法英语词汇fine blanking 精密下料加工finish blanking 光制下料加工adjustable spanner 活动扳手finishing 精整加工angle cutter 角铣刀flanging 凸缘加工arbour 心轴folding 折边弯曲加工backing 衬垫folding 摺叠加工belt sander 带式打磨机forming 成形加工buffing 抛光impact extrusion 冲击挤压加工chamfering machine 倒角机indenting 压痕加工chamfering tool 去角刀具ironing 引缩加工chisel 扁錾knurling 滚花chuck 夹具lock seaming 固定接合compass 两角规louvering 百叶窗板加工concave cutter 凹面铣刀marking 刻印加工convex cutter 凸形铣刀necking 颈缩加工cross joint 十字接头notching 冲口加工cutting edge clearance 刃口余隙角parting 分断加工drill stand 钻台piercing 冲孔加工edge file 刃用锉刀progressive bending 连续弯曲加工file 锉刀progressive blanking连续下料加工flange joint 凸缘接头progressive drawing shaving连续引伸加工缺口修整加工grinder metal saw砂轮机金工锯progressive forming shearing连续成形加工切断加工hammer nose angle铁锤刀角reaming sizing铰孔加工精压加工hand brace /手摇钻矫正加工restriking pinchers二次精冲加工钳子hatching slitting剖面线割缝加工riveting pliers铆接加工铗钳hexagon headed bolt plug六角头螺栓柱塞头roll bending spinning滚筒弯曲加工卷边hexagon nut ?六角螺帽接roll finishing polisher滚压加工磨光器index head stamping分度头锻压加工rolling protable driller 压延加工手提钻孔机jack swaging千斤顶挤锻压加工roughing punch粗加工冲头jig trimming治具整缘加工scrapless machining sand paper无废料加工砂纸kit upsetting工具箱锻粗加工seaming scraper折弯重叠加工刮刀lapping wiring研磨抽线加工screw driver 螺丝起子scribing 划线second out file 中纹锉spanner 扳手spline broach 方栓槽拉刀square 直角尺square sleeker 方形镘刀encapsulation molding 低压封装成型、射出成型用模具two plate 两极式（模具）well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spindle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道welding line 熔合痕eject pin 顶出针knock pin 顶出销return pin 回位销反顶针sleave 套筒stripper plate 脱料板insert core 放置入子runner stripper plate 浇道脱料板guide pin 导销eject rod （bar）（成型机）顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orientation 定向sprue gate 射料浇口，直浇口nozzle 射嘴sprue lock pin 料头钩销（拉料杆）slag well 冷料井side gate 侧浇口edge gate 侧缘浇口tab gate搭接浇口film gate 薄膜浇口Linear Cutting 线割wire-cutElectrical Sparkle 电火花EDM 唧嘴：sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch 边司/ 导套：bushing/guide bushing stock removal 切削cross feature 交叉部分weld 烧焊corner pad 立面图套角elevation 提高，上移，立体图，高处代表typical draft 斜度垂直壁面vertical radius 半径直径diameter 壁面notch PL 分型面weld sealoff for slot 封胶面烧焊，形成凹槽顶针：ejector pin 螺丝：screw 顶针板：ejector retainner plate Pin 销Guide Pin 导正销flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口subarine gate 潜入式浇口tunnel gate 隧道式浇口pin gate 针点浇口Runner less 无浇道(sprue less) 无射料管方式long nozzle 延长喷嘴方式sprue 浇口溶渣square trowel 直角度stripping 奥氏体剥离工具bainiteT-slot T 贝氏体形槽banded structuretool for lathe 条纹状组织车刀barrel platingtool point angle 滚镀刀刃角barrel tumblingtool post 滚筒打光刀架blackeningtosecan 染黑法划线盘blue shortnesstrimming 青熟脆性去毛边bonderizingwaffle die flattening 磷酸盐皮膜处理压纹效平box annealingwiper 箱型退火脱模钳box carburizingwrench 封箱渗碳螺旋扳手bright electroplating八辉面电镀bright heat treatment模具表面处理英语词汇光辉热处理age hardening bypass heat treatment时效硬化旁路热处理ageing carbide老化处理炭化物air hardening carburized case depth气体硬化浸碳硬化深层air patenting carburizing空气韧化渗碳annealing cementite退火炭化铁anode effect chemical plating阳极效应化学电镀anodizing chemical vapor deposition 阳极氧化处理化学蒸镀atomloy treatment coarsening阿托木洛伊表面结晶粒粗大化austempering coating奥氏体等温淬火涂布被覆austenite cold shortness奥斯田体低温脆性/ comemtite渗碳体controlled atmosphere 大气热处理corner effect 锐角效应creeping discharge 蠕缓放电decarburization 脱碳处理decarburizing 脱碳退火depth of hardening 硬化深层diffusion 扩散diffusion annealing 扩散退火electrolytic hardening 电解淬火embossing 压花etching 表面蚀刻ferrite 肥粒铁first stage annealing 第一段退火flame hardening 火焰硬化flame treatment 火焰处理full annealing 完全退火gaseous cyaniding 气体氧化法globular cementite 球状炭化铁grain size 结晶粒度granolite treatment 磷酸溶液热处理graphitizing 石墨退火塑件模具专业英语词汇大全compre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具配镶件:making inserts 清角：clearance。