海洋钢结构制造专业英语词汇大全

合集下载

钢结构常用单词

钢结构常用英语单词ABOM 预估料单Anchor 锚固Anchor bolt 锚栓，Chemical anchor bolt 化学锚栓Anchor rod 锚杆Angle 角钢Axial 轴向的Back gouge 清根Backing bar/strip 背垫衬条（焊接用）Backstay 刚性梁Bar 棒材Bar code 条形码Base plate 底板Beam 梁Bearing 承压的，轴承Bearing bar 承载条，serration type锯齿型，plain type 直边型Bending 弯曲Bent plate 折弯板Bevel 坡口Beveled/Tapered washer 斜垫圈Blasting 喷扫Block 块，框；Title block 标题框Blueprint 蓝图Bolt 螺栓，Stud bolt 双头螺栓BOM 料单Both sides(B.S) 二侧Bottom 底Box girder 箱式板梁Brace 斜拉Bracing 斜拉（总称）Bracket 托架Built-up member 组合构件Butt joint 对接缝Butt weld 对接焊缝Cable tray 电缆槽架Cage 护笼Camber 起拱Cantilevered beam 悬臂梁Cap plate 盖帽板Cast in 埋入的Casting 浇铸件Center of gravity（C.O.G）重心Chain 链Chamfer 倒角，倒棱Channel 槽钢Check-Review-Approval 检查-审阅-批准Checker 审图员Checkered plate 花纹板Chord 弦Cladding 建筑物金属外覆盖面Clearance 净空、间隙距Cleat 隅角板，连接板Clevis U形夹Clip 卡子、剪去（动词）Cloud-line 云雾线Coat涂层: Primer底漆, undercoat中间漆, top/cover/finish coat 面漆Coating 涂料Cold formed冷成形的Color code 色卡号Column 立柱Component 部件Compression member 受压构件Complete penetration (CP) 全熔透Complete joint penetration(CJP) 全熔透Concrete 混凝土Connection 连接，节点Connection detail 节点详图Connection plate/angle 连接板/角钢Continuous beam 连续梁Continuous weld 连续焊缝Cope开锁口，锁口Corrugated sheet 波纹板Cotter pin 开口销Countersink 埋头Cover plate 盖板Crane 吊车Crane runway girder 吊车梁Crane stop 吊车止挡Cross/Transverse/Lateral 横向的Cross bar 横条Cross bracing 交叉斜拉Cross section 横截面Cut 切割，切口；Cut out 开口Datum line 基准线Dead load 恒负荷Deck 甲板Decking 复合混凝土层面中的压型钢板Deflection 挠度/曲Deformed bar 螺纹钢筋Design drawing 设计图Detail 详图Diagonal bracing 对角斜拉Diameter 直径Dimension 尺寸Direction 方向Drift pin 对孔用的打入销Drill 钻孔Drop in/Laid in 嵌入的Dowel 定位销Edge distance 边缘距Elevation 立面图，标高Embedment 埋件Edge 边缘Edge preparation 边缘开坡口End 端头End preparation端头开坡口Epoxy 环氧Erection 安装Erection bolt 安装螺栓Erection drawing 安装图Erection mark 安装标记Expansion bolt 膨胀螺栓Fabrication 制作Face 面Far face (F.F) 远的那面Fastener 紧固件Faying/contact surface 摩擦/接触面Field 现场Field bolt/weld 现场螺栓/焊缝Filler 填充板Fillet 内角Fillet weld (FW) 角焊缝Finish 面漆，精整的表面Fixed 固定的Flame火焰Flame cut 火焰切割Flange 翼缘，法兰Flange plate 翼缘板Flange weld 翼缘焊缝Flat bar 扁钢Floor 层面、地板Flooring 层面材料Floor plate 层面板Flush 平齐的Footing 立柱墩Forging 锻件Foundation 基础Frame 框架Full penetration (FP) 全熔透Gable 缆绳Gage 螺栓排中心距Gage line螺栓排中心线Galvanization镀锌；hot dip ∽，electro-∽，mechanical ∽热浸/电/机械镀锌Gantry 龙门吊Gap 间隙Girder 板梁Girt 墙面檩条Grade材质Grating 格栅Grating panel格栅板Gridline 轴线Grillage 排栅Grip 螺栓夹紧厚度Groove weld 坡口焊缝GRP 玻璃钢Grout 灰浆Gusset plate 节点板Hand hole 手孔Handrail 栏杆Hanger 吊杆High-strength bolt 高强螺栓Hinger 合页Hole 孔，洞Hollow structural shape(HSS)中空型钢: CHS, RHS, SHS圆/长方/方管（有缝）Hook 吊钩Horizontal 水平的Impact test 冲击试验Inclined/Raked 斜的Item/piece number 件号Jig and fixture胎具Joist 托梁Joint 接头，接缝Joint preparation 开焊接坡口Kickplate/toe plate 踢脚板Ladder 爬梯Landing 梯子平台Laying out 放样Layout 布置Left 左Leg 腿，直角边Level 标高，水平Load 负荷，Dead load恒负荷，Live load动负荷Location 位置Longitudinal 纵向的Lug 板式吊耳，耳片Match mark 配合标记Member 构件Mill 钢厂Milled surface 机加工面Modeling 建模Module 模块MTO 材料估算Near face (N.F) 近的那面Neoprene氯丁橡胶Nominal size公称尺寸Nosing 踏级防滑条Nut 螺母，Lock nut锁紧螺母Opening 开口Orientation 方位Packer 垫板Paint 油漆Painting 涂装Panel 板块Parallel 平行的Partial penetration(PP) 部分熔透Penetration hole 穿越孔Perpendicular 垂直的Pier 码头，墩Pile 桩Pin 销Pipe 管Pitch 纵向上的螺栓间距Plan 平面图Plate 板Platform 平台Plug 堵头Primer 底漆Projection 投影，突出量Pole 杆Position 位置Post 栏柱Profile 型钢，断面Profile sheet 压型钢板Purlin 屋面檩条Radius 半径Rafter 人字梁Rail 道轨，横杆Ream 铰孔，扩孔Reinforced bar 钢筋Rib 肋板Right 右Rod 圆钢Rolled 轧制的Roof 屋面Roofing 屋面材料Round/Circular 圆的Rubber 橡胶Rust 铁锈Sag rod 抗弛杆Scale 氧化皮Seal 密封，Seal weld密封焊缝Sealant密封剂Section 截面，剖视，型钢Self tapping screw 自攻螺钉Shackle 卸扣Shape 型钢，形状Shear 剪切Sheet 薄板，纸页Sheeting 压型钢板Shim 垫片Shipping 海运Shop 车间Shop drawing 车间工作图Siding 墙面材料Sketch 草图Slab 混凝土板Sleeve 套筒Slide 滑动的Slip-critical joint/Friction grip joint 摩擦型连接Slope 坡度Slot 槽Smooth 光滑的Snug tightened bolt 上紧到板紧贴程度的螺栓Snipe 剪去Spacing 间距Span 跨度Splice 拼接Square 方的，直角的Stair tread 梯踏级Stair/staircase 楼梯Stanchion 柱Stiffener 加劲板Stool 支墩Stitch weld 跳焊Stringer 纵梁Strut 支柱Stub column 短立柱Stud/Shear connector 栓钉Support 支架Surface 表面Surface preparation 表面处理Tack weld 点焊Tape 胶带Tee steel T型钢Teflon 聚四氟乙烯Template 样板，模板Tension member 受拉构件Threaded rod 螺杆Tie 系杆Tier 层，柱节Top 顶T.O.C 混凝土顶面T.O.S 钢件顶面Truss 桁架Trunnion 管式吊耳Tube 非标管Turnbuckle 花兰螺套Underside 底面Unit 单位，Metric unit公制单位，Imperial unit英制单位Vertical 垂直的View 视图W alkway 走道W asher 垫圈W eld 焊接，焊缝W eld access hole 过焊孔W eld pass/run 焊道W eld reinforcement 焊缝余高W eld root 焊缝根部，打底焊道W elded焊接的Wire 钢丝，铁丝Yield 屈服。

钢结构工程词汇(全)

钢结构工程词汇（全）（全面完整资料，可直接使用，可编辑，推荐下载）钢结构词汇参考(xsteel)Aactive area 有效面积ANCHOR 锚ANCHOR BOLT锚栓angle 角钢angle brace 隅撑angle leg 角钢肢angle with equal legs 等肢角钢angle with unequal legs 不等肢角钢aperture 孔径arch beam 拱梁area of section 截面面积area of structural steel 型钢截面面积assembly 构件awning 雨篷BBackplan 底视图baffle plate 隔板bar 条钢base PL.底板backfilling plate 垫板batten plate 缀板battened grating栅格板beam 次梁bearing bar 横杆bearing plate 支承板bend 弯头（弯曲半径）bent排架bevel 倾斜的，坡口bevel cut 斜切BILL 清单BILL OF MATERIAL 材料表bracket 牛腿bridging 拉条(澳洲)bolt 螺栓bolted steel structure 螺栓连接钢结构building 建筑built-up steel column格构式钢柱butt weld 对接焊缝Ccamber 拱，起拱cantilever beam 挑梁cap PL.盖板CHUTE 滑运槽circuit 电路CLEAN COAL 洗煤clearance 净距clip angle 角钢夹板COLLECTING CONVEYOR 集煤传送带column 柱子column bracing 柱间支撑concrete 混凝土connections of steel structure 钢结构连接constant cross-section column 等截面柱continuous weld 连续焊缝COUNTERWEIGHT 平衡器coupling wall-beam 联系梁cover plate 盖板CONVEYOR DESK 传送台CRANE 吊车crane girder 吊车梁criteria 标准cross beam 井字梁custom 自定义custom component 自定义组件cyclone 旋流器Ddesignations of steel钢材牌号detail 详图，零件图，细部detailer 详图员dimension 尺寸（线）diaphragm 横隔板double angle bracing 双角钢支撑E edition 版本elevation view主视图embedded parts 预埋件end plate 端板engineering drawing 工程图EXP METAL = expanded metal 金属网FF=freeze 冻结field welding现场焊filler plate 填板fillet weld 角焊缝finish floor 楼面装修层地板FLATTENED 展平的floor board 楼面板floor depth 楼板厚度floor plate 楼板floor topping 楼板面层flange翼缘G G= arrange drawing 布置图gable roof truss 人字形屋架gable column 山墙柱galvanized 镀锌的grid 轴线grid plane轴线平面girder 主梁girth墙梁groove 坡口gusset plate 节点板gutter 檐沟Hhead room 净高haunch 腋high-strength bolt 高强度螺栓high-strength bolted connection 高强度螺栓连接hinged connection 铰接hollow section中空截面horizontal bracing 横向水平支撑（transverse bracing）horizontal stiffener横向加劲肋（transverse stiffener）horizontal weld横向焊缝（transverse weld）hot-rolled section steel 热轧型钢HS. 承压型（螺栓）hunched beam 加腋梁II= issue v.发行inclined section 斜截面incomplete penetration 未焊透incompletely filled groove 未焊满intermediate stiffener 中间加劲肋intermittent weld 断续焊缝ITEM NO. 项目编号JJack bolt 定位螺栓Jagging 开槽口job location 施工现场job shop 加工车间job schedule 工程进度表joggled beam 拼接梁joining beam联系梁joining plate 连接板joist托梁joint flange 接合法兰joint free 无缝的joist steel 工字钢Kknee brace隅撑，角撑knee pipe 弯管kick plate 踢脚板killesse 槽钢king rod 腹杆LLabel v. 标注（lace v.扎带子，缚带子）laced of battened compression member 格构式钢柱lacing and batten elements 缀材(缀件)lacing bar 缀条ladder 爬梯landing 楼梯平台leg肢leg size of fillet weld 角焊缝焊脚尺寸LLH. = long leg horizontal angle 长肢水平角钢longitude horizontal bracing 纵向水平支撑longitudinal brace纵向拉条longitudinal weld纵向焊缝longitudinal tie 纵拉杆MM= multiple drawing 多构件图main member 主构件man lock column 开孔柱material 原料multiple span girder多跨梁Nnon-uniform cross-section beam 变截面粱normal section 正截面notch 槽口nut 螺母O oblique section 斜截面outline plane主要平面outstanding width of flange 翼缘板外伸宽outstanding width of stiffener 加劲肋外伸宽度Ppadding plate 垫板part 零件，部件perspective view透视图piece mark 零件标号pipe 圆管plate 板plank 板材portal span 门式刚架（portal 入口）post 立杆，小立柱PULLEY STAND 滑车架PULLEY GUARD 滑车防护装置punched hole 冲孔purling檩条Rrabbet 槽口rail扶手reference line 参考线rigid framed structure 刚架结构remove v.去掉resting 楼梯平台Rev= revision 修正ridge line 屋脊线(rigid connection 刚接)right angle 直角R= rise 踏步之间竖向距离rise of a flight ＝rise梯级高度rise of flight 梯段高度riser board 踏步竖板rod 杆roof girder 屋面梁roof plate 屋面板roof truss 屋架round tube 圆管run 踏步之间水平间距Ssag rod拉条，（系杆，吊杆）SAMPLER ACCESS PLATFORM 取样通道平台scale 比例scaling drawing 设计图secondary beam 次粱section plane 剖面section steel 型钢shear plane 剪面shear plate simple 单剪板shear splice 抗剪拼接short stiffener 短加劲肋shop drawing 加工图shop-fabricated member 工厂预制构件single slope roof 单坡屋顶slab 楼层板slope 斜坡slope angle 倾角slope of stair 楼梯坡度slope of roof 屋面坡度sloping beam 斜梁sloping plate斜板sloping roof 斜屋顶sloping side 斜边slot 长孔slotted hole 长圆孔slotted angle 开槽角钢slotting 开槽SP.= splice connection拼接节点space v.间隔specification 规范stair＝staircase楼梯stairway width 楼梯宽度stair landing楼梯平台stair tread 楼梯踏步stanchion 立杆（栏杆中）stitch连接stitch detail 细部连接stringer 楼梯斜梁stub 短柱stud 栓钉steel column base钢柱脚steel pipe 钢管stepped column 阶形柱stiffener 加劲肋storey 层storey height 层高strength classes of structural steel 钢材强度等级SUPPORT POST 立柱TT= tread 踏板长度tab plate 接头板thickness 厚度tie拉杆toe plate 踢脚板transfer conveyor 传送带(trapezoid 梯形)trapezoid roof truss 梯形屋架tread 踏步triangular roof truss 三角形屋架truss 桁架TS. 摩擦型（螺栓）Tube 管two sides(edges supported plate 两边支承板Uuniform cross-section beam 等截面粱（cross-section 横截面）V valley beam斜梁vertical bracing 竖向支撑WW =widget 单部件(single part )washer 垫圈web 腹板web member 腹杆weld bead焊缝weld bead height 焊缝高度weld bead length 焊缝长度welded steel beam 焊接钢梁welding connection 焊缝连接windcolumn 抗风柱welding rod 焊条welding wire焊丝Yyield stress 钢材屈服点ZZinc 锌zinc coating hole镀锌孔疑问：1． Allinment 什么意思？AFTER FINIAL ALLINMENT AND WELDFor sale a 2003 Kia SedonaMinivan. Everything has been kept up to date oil changes, brakes, allinment, new rackopinion, winter studded tires plus summer tires. It is inspected and on the road now. The van is in excellant shape we are only selling it to buy a truck to haul our travel trailer.2． Hilti kwik bolt 什么意思？参见2962-0001-0014 3.H.M. = ?参见2977-3000-3010。

海洋工程英语词汇 Word版

海工英语词汇

一. 技术词汇AA-60 fire door A－60级防火门Abrasive (喷砂用的)磨料abrasive paper 砂纸AC generator 交流发电机AC motor 交流电动机Accelerated corrosion testing 加速腐蚀试验Acceptance criteria 合格准则access hole (for welding)= cope hole (焊接)工艺孔accommodation and power platform (APP)生活动力平台according to = in accordance with = in line with = as per =in the light of 按照acetylene gas 乙炔acid electrode 酸性焊条acid proof cement 防酸水泥Additive 添加剂adhere to 遵守(动词)Adherence to 遵守(名词)adjacent columns 相邻立柱adverse combination of loads 荷载的不利组合adverse condition 不利条件aeronautical radio system 航空无线电系统AFC (approved for construction) 建造批准aforementioned 上述的aft winch 船艉绞车Agitator搅拌器a-hundred-year return period 百年一遇air blower 鼓风机air compressor 空压机air driven pump 气动泵air hoister 气动绞车air manifold 气包air tight test 气密性试验aircraft obstruction beacon 航空障碍灯air-hose 风带alarm buzzer 报警蜂鸣器alarm horn 报警喇叭aliphatic polyurethane 脂肪族聚氨酯漆Allowable(working) stress 许用应力Aluminum alloy anode 铝合金阳极Aluminum ingot 铝锭Aluminum paint 银粉漆Aluminum sheet 铝皮ambient air temperature 环境气温ambient temperature 环境温度anchor block 地锚块anchor bolt 地脚螺栓anchor ground 锚地anchor pile 锚桩anchor profile 磨料喷入母材的深度anchor pattern 磨料喷后母材留下的小坑形状(圆形、角形等)anchor rack 锚架anchoring buoy 锚泊浮筒angle of incidence 入射角angle of reflection 折射角angle probe method 超声波斜射探伤angle steel 角钢angle valve 角阀anode core 阳极芯子anode end face geometry 阳极端面几何形状anode life 阳极寿命anode potential 阳极电位anode stand-off post 支架式阳极的立柱anodic resistance 阳极电阻anticorrosive paint 防锈漆anti-electrostatic floor 防静电地板antipollution measures 防污染措施API specified requirements A PI规定的要求apparent batter 视斜度applicable API specification API 适用规范approach-departure sector直升飞机起落扇形区Appurtenance=attachment=accessory=auxiliary附件arc air gouging 碳弧气刨arc cutting 电弧切割arc strike 弧击argon arc welding 氩弧焊argon arc welding machine 氩弧焊机articulated tower mooring system铰接塔系泊系统artificial island 人工岛as per 按照as-built 完工as-built dossier 完工资料as-built drawing 完工图as-rolled 轧制状态Assemble 组装(动词)Assembly 组装(名词)Associated gas 伴生气at the option of A 按A的意愿atmospheric diving system= unpressurized diving system 常压潜水系统atmospheric vent 放空管attachments 附件auto fire alarm system 火灾自动报警系统automatic spraying system 自动喷淋系统B(to be ) buttered (焊接的)长肉back chipping 清根back gouging 反面气刨Backing weld 打底焊道backpressure regulator (self contained) 背压式调节阀(自力式)backwash return pump 反冲洗回流泵backwash surge tank 反冲洗罐backwash tank 反冲洗水罐Ball hardness 布氏硬度ball valve 球阀Bar (截面较小的)圆钢方钢六角钢等bar chart 统计用的柱状图barge bumper 靠船件barge strength and stability 驳船强度及稳性Barrel (管件的)加厚段base metal 母材、基本金属basic design 基本设计basic electrode= lime type covered electrode 碱性焊条battery room 蓄电池间beam depth 梁高beam path distance 超声波发射程距bearing strength of the ground 地基承载力bearing stress支撑应力before welding is initiated 始焊前Bending moment 弯矩Bending stress 弯曲应力Bevel 坡口bevel angle 坡口面角度Beveling / chamfering 开坡口bid / tender for ... 投标bid drawing 招标图纸bilge alarm system 污水报警系统bilge/ fire pump 舱底污水－消防两用泵blast cleaning 喷砂除锈blind flange 盲法兰blind spectacle flange 快速盲法兰blow count 打桩的锤击数Blowdown vessel 排放罐blowhole; gas pore 气孔blowout preventer stack 防喷器组blowout preventer system(BOP system) 防喷器系统boat landing 登船平台bolt, nut and washer 螺栓、螺母及垫片bolted connection螺栓连接Boom 吊机扒杆boom angle 吊臂倾斜角bore hole 镗孔boss with plug 带有丝堵的管座bottom echo 底面回声bottom sitting drilling platform 坐底式钻井船Boundary condition 边界条件Bow 船艏box beam 箱形梁box type joint 箱形节点Brace 拉筋bracelet anode 手镯式阳极branch member 支杆breathing apparatus , respirator 防毒面具Bridge 栈桥bridge (overhead) crane 天车吊Brittleness 脆性brush coating 用毛刷涂漆buckle fastener 绑带build-up girder 组合梁bulb angle 球扁钢bulk head 隔板，舱壁，刚性法兰(海管) buoyant turret mooring 浮筒转塔式系泊burn through 烧穿Burner 气焊工burr and flashing 飞边毛刺business and management 经营管理Butterfly valve 蝶阀butt-welded seam 对接焊缝Ccable hanger 电缆马脚cable layer 敷缆船cable rack /tray 电缆托架Caisson 沉箱caisson washing pump 洗舱泵caisson-type platform 沉箱式平台Can (管件的)段Cantilever beam 悬臂梁Cantilever jack-up rig 悬臂自升式钻井船Cantilever well module 悬臂式井口模块cap beam帽梁capped steel 半镇静钢capsizing lever 倾覆力臂capsizing moment=overturn moment 倾覆力矩carbon arc air gouging 碳弧气刨carbon dioxide cylinder 二氧化碳气瓶carbon equivalent 碳当量carbon-dioxide(CO2) arc welding 二氧化碳气体保护电弧焊cargo master system 货油舱总监控系统cargo tank cleaning machine 洗舱机Carrier (搬运)小车carry out = perform = conduct= execute 进行、执行catenary anchor leg mooring (CALM) 悬链锚腿系泊cathodic protection 阴极保护cellar deck 底甲板cellar shutdown panel (CSDP)井口系统关断盘cement grout 水泥浆cementing vessel 固井船center line 中心线center of buoyancy 浮心center of floatation 漂心center of gravity 重心center punch 冲子central control room (CCR) 中央控制室central processing platform 中心处理平台centrifugal pump 离心泵Centrifuger 离心机ceramic fibres 防火陶棉ceramic tiles 瓷砖certifying authority 第三方检验机构chain block 倒链、链滑车chair with arm-rests 带扶手的半软椅Chamfering 开坡口channel steel 槽钢charpy-V notch energy 夏比V形缺口韧性值charpy-V notch impact test 夏比V形缺口冲击试验chart datum 海图基准面check randomly 抽检check valve 止回阀checkered plate 花纹板chemical composition 化学成分chemical injection package 化学注入撬chemical injection system 化学药剂注入系统chemical seal 化学密封chipping hammer 敲渣锤Chisel 风铲Chord member 弦杆Christmas tree 采油树circumference 周长circumferential weld 环焊缝classification survey 入级检验clean water injection pump 清水注入泵clean water surge tank 清水缓冲罐Clearance 间隙Client 业主、顾客close drain tank 闭式排放罐closed / open circuit 闭/开路Closed drain pump 闭式排放泵closed drain tank 闭式排放罐clustered well heads 丛式井口CO2 cylinder unit CO2 气瓶组CO2 extinguisher C O2 灭火器coal tar epoxy paint 含焦油环氧涂料Coaming 档水扁钢Coating 涂装coating interval 涂漆间隔Coefficient 系数Cold formed pipe 冷卷管cold shut 冷隔cold work 冷加工、冷作collapse ring 加强环板Column 立柱combustible gas detector 可燃气体探测器Come-along 手搬葫芦commercial blast cleaning 普通级喷砂除锈commissioning 调试compile and maintain a document编制和保存文件complete penetration groove weld 全熔透坡口焊Completion riser 完井立管complex joint 复杂节点Compliance with 符合(名词)comply with 符合(动词)composite rockwool ceiling 复合岩棉天花板composite rockwool panel 复合岩棉板concentric reducer 同心大小头Conceptual design 概念设计concrete platform 混凝土平台Condensate drum 冷凝液罐Condensing water 冷凝水Conductor 隔水套管conductor guide 套管导向Cone 大小口、锥体conform to = stick to = adhere to 符合、遵守Connection 节点、连接consumption rate 阳极消耗率Continuous beam 连续梁Continuous double fillet weld 双面连续贴角焊Continuous welding 连续焊Contract 合同Contraction stress 收缩应力Contractor 承包商control valve (accessories handwheel) 带手轮的控制阀control valve assembly 控制阀总成coordinates 坐标系coordination 协调cope hole (焊接)工艺孔corrective and preventive action纠正和预防措施Correlation curve 相关曲线corrosion allowance 腐蚀余量corrosion coupon 腐蚀挂片corrosion protection 防腐Corrugated plate interceptor 斜板分离器Couplant UT用的耦合剂Coupling 连轴器、管箍Crack 裂纹crane barge, crane vessel 起重船crane support 吊机支撑Crater 焊口crawler crane 履带吊车Criteria (验收)标准cross angle 交叉角cross section 横截面crow bar 撬杠cruciform bollard 单十字带缆柱crude cooler 原油冷却器crude filter 原油过滤器crude heat exchanger 原油换热器crude loading /export pump 原油外输泵crude loading pump 原油装载泵crude oil drain tank 原油排放舱crude preheat exchanger 原油预热器crude suction strainer 原油吸入滤器crude transfer pump 原油输送泵cup support 垫墩curing time (油漆的)固化时间Current capacity (阳极的)电流容量Current density (阳极的)电流密度Current direction 海流方向curvature radius 曲率半径Customer (试比较purchaser 需方) 客户(签合同后,客户变需方)cut by torch 以火焰切割cut off 割除、割除物cutoff allowance 切割裕量Cutting plan 排板图Cutting sheet 单件图D( in ) duplicate 一式两份(to)drive piles 打桩DAC curves 距离-振幅曲线daily diesel filter 日用柴油滤器damage-prone connection 易破坏的节点Damper, dampener 减振器DC generator 直流发电机Decibel (dB) 分贝deck beam 甲板梁deck cover 甲板敷料deck crane 甲板吊车deck floor plate 甲板板deck water seal unit 甲板水封装置deep freeze compressor 深冷压缩机deepwater jacket 深水导管架defect /default /disconnection 缺陷Deflection 挠度dehydration degassing vessel脱水除气器dehydration preheater 脱水预热器dehydrator feed pump 电脱水供给泵delivery of materials 材料交货Derrick barge 回转式起重船Desander 除砂罐design basis 设计基准design parameters 设计参数Detail 详图detail design 详细设计develop / establish a document 编制文件dew point 露点DFT(dry film thickness) 干膜厚度diagonal brace 斜拉筋dial gauge 百分表Diaphragm 隔板diaphragm valve 隔膜阀die stamp 钢印diesel daily tank 柴油日用罐diesel filter coalescer 柴油过滤净化装置diesel generator set 柴油发电机组diesel oil daily tank with heater 柴油日用罐(带加热器)diesel pump 柴油泵diesel storage tank 柴油储罐diesel storage tank with heater 柴油储罐(带加热器)diesel tank 柴油罐diesel transfer pump 柴油输送泵differential pressure control valve 差压控制阀Diffuser 布风器dihedral angle 二面角dimensional checks 尺寸检验direct / alternating current arc welding 直/交流电弧焊Direct current emergency supply 直流应急电源Disassembling 拆除Discontinuity 缺陷displacement oil tank 置换油罐distortion from welding 焊接变形Distress signals 遇险呼救信号Diver 潜水员diver support vessel 潜水作业船document approval and issue 文件的批准和下发Documentation 文件编制Dog 组装用的刀把Dolphin 系缆柱domestic sea water pump 生活海水泵double agent facility 双介质灭火装置double bed 双层床double bevel groove K 形坡口double bollard 双柱带缆柱double groove 双面坡口double probe method 双探头法Double V groove 双面V 形坡口(X 形坡口) doubler plate 垫板、包板down hill welding 下向焊drain pit 排放池draught gauge 吃水标尺drawing and specification 图纸及技术规格书drawing types 图纸种类Drilling module 钻井模块Drilling platform 钻井平台Drilling template 钻井基盘drillship ,drilling ship 浮式钻井船Driving voltage 驱动电压dry chemical extinguisher 干粉灭火器Dryer 烘箱dry-type tree 干式采油树during the course of fabrication在制造过程中during the life of structures 结构寿命期间dye penetrant inspection8 着色检验dynamic-positioning rig 动力定位钻井船Dredger 挖泥船drift pin 心轴、销子drift test 管流试验、管线试通Drill 钻头图纸种类有：conceptual drawing 概念图纸basic drawing 基本设计图bid drawing 招标图纸design drawing 详细设计图fabrication drawing 加工设计图shop drawing 车间加工图as-built drawing 完工图Eearth lead 地线eccentric reducer 偏心大小头echo height 回波高度edge crimping (卷管的)压头edge preparation 坡口加工effective throat thickness 焊缝计算厚度elbow 弯头electric dehydrator 电脱水器electric desalter 电脱盐器electric drill 手电钻electric heater 电加热器electric submersible pump 电潜泵electrical connection 导电连接electric-hydraulic valve 电-液操作阀electrochemical property 电化学特性electrode 电焊条electrode covering 焊条药皮electrode holder 焊把、焊钳electrolyte 电解质electro-slag welding 电渣焊接elevation (EL) 标高、立面图elongation 延伸率emergency air compressor 应急空压机emergency ballast control system 应急压载控制系统emergency BOP recovery system 防喷器紧急回收系统emergency generator 应急发电机emergency light 应急照明灯emergency power station 应急电站emergency shutdown 紧急关断emergency shutdown system (ESD) 应急关断系统emergency switch board 应急开关柜emergency switch room 应急配电间emery cloth 金刚砂布emulsion transfer pump 乳化油输送泵engine room 动力舱、机舱engineering geotechnical vessel 工程地质船engineering vessel 工程船舶entire length 全长equal angle 等边角钢equation 公式equipment base 设备底座erection 安装ERW (electric resistance welding) 电阻焊escape route 逃生路线essential variable 焊接基本参数excess of weight超重existing structure 已有结构explosion proof equipment 防爆设备exposure distance 防火距离extent of defect in %缺陷百分率extent of inspection 检验范围extent of repair 返修率external surface of brace 拉筋的外表面extra margin of stress 应力裕量Ffabricated wide flange shape焊接成的宽翼缘型钢fabrication aids 制造辅助物(如临时吊点) fabrication design 加工设计fabrication phase 制造阶段fabrication sequence 制造顺序fabrication yard 制造场地face bend test 表面弯曲试验facsimile transceiver 传真收发两用机fastener 紧固件fatigue damage 疲劳破坏field assembly 空间组对、现场组对field mating point 海上对接点(如导管架与组块对接点)field splice 现场拼接field weld 现场焊缝fifty year return period 五十年一遇file 锉刀filler metal 填充金属final fabrication tolerance 最终制造公差finish coat 面漆finished product 成品finite element analyses 有限元分析fire alarm siren 火灾警笛fire and gas detecting system 火灾－可燃气探测系统fire control panel 消防控制盘fire damper 防火风闸fire door closer, fire proof door 防火门fire extinguishing system 消防系统fire fighting water , fire water 消防水fire foam hydrant 消防泡沫栓fire hose station , hose box 消防箱fire monitor 消防炮fire panel火灾－可燃气报警显示盘fire proof wall , fire wall 防火墙fire protected plastic tiles 防火塑料地板fire protection wall 防火墙fire station 消防软管箱fire water / foam monitor 消防炮(水或泡沫)fire water deluge system 大水量灭火系统fire water hose rock 消防水软管fire water hydrant 消防水栓fire water jockey pump 消防水增压泵fire water lift pump 消防水提升泵fire water pump 消防水泵fire-fighting vessel , fire boat 消防船fireman box 消防员箱first aid kit 急救箱first coat 底漆first stage hydro cyclone 一级水力旋流器first stage separator 一级分离器fitter 组装工fit-up 坡口组对fixed crude oil washing machine 固定式原油清洗机fixed drilling platform 固定式钻井平台fixed platform 固定式平台fixed tower SPM 塔系泊flame arrester 阻火器flame cutting 火焰切割flame cutting droplets and debris 火焰切割形成的熔滴和料头flame cutting machine 火焰切割机flame cutting torch 火焰割枪flammability limits 可燃度极限flange 翼缘、法兰flare assembly 火炬总成flare boom 火炬臂flare drum 闪蒸罐flare pilot gas 火炬引燃器flare scrubber 火炬分液器flare tower 火炬塔flat bar 扁钢flat plate anode 扁阳极flat welding 平焊flaw 裂纹flaw detectability 缺陷检测灵敏度flaw echo 缺陷回声flexible hose 柔性软管flexible riser 挠性立管floater controlled valve 浮球控制阀floating cargo hose 浮式输油软管floating loading hose 浮式装油软管floating oil production and storage unit (FPSU)浮式生产储油装置floating oil storage unit 浮式储油装置floating production platform 浮式生产平台floating production, storage and off-loading tanker 浮式生产储油外输轮floating state 飘浮状态flooding 注水floppy disk 软盘flow chart 流程图flow indicator (FI) 流量显示器flow quantity recorder (FQ) 累计流量计flow switch 流量开关flux 焊药flux cored arc welding (FCAW) 药芯焊flux-cored electrode 管状焊条flux-cored wire 药芯焊丝foam extinguishing system固定式泡沫灭火系统foam monitor泡沫炮foam station 泡沫站fog horn , fog signal 雾笛folding bed 折叠床folding chair 折叠椅foot print 被交位置foot valve 底阀forecastle 艏楼foreman领班forged steel (FS) 锻钢fork lift 铲车、叉车forming 压制成型forming of plates into tubular 由板卷成管formula / equation of carbon equivalent 碳当量公式four way valve 四通阀fracture toughness 断裂韧性frame structure 梁格结构free water knockout vessel 游离水分离器fresh water pressure vessel 淡水压力罐fresh water pump 淡水泵fresh water tank with electric heater淡水罐(带加热器)friction coefficient 摩擦系数fuel gas compressor package 燃气压缩机撬fuel gas heater 燃料气加热器fuel gas scrubber 燃气洗涤器fuel gas treatment package 燃料气处理撬fuel oil drain tank燃料油排放罐fuel pump 燃油泵full coupling 全螺纹的接头full penetration weld全熔透焊缝funnel-shaped guide 喇叭口状导向furnace 熔炉、加热炉fusible plug 易熔塞fusion /bond line 熔合线G(to be ) ground flush 磨平gantry crane 龙门吊gap gauge 间隙尺gas bottle 气瓶gas cutting 气割gas cutting machine with magnetic wheels 磁轮式气割机gas detector 可燃气体探测器gas export facility 天然气外输设施gas injection module注气组块gas metal arc welding (GMAW) 熔化极气体保护焊gas processing plant 天然气处理厂gas shielded arc welding 气体保护电弧焊gas tungsten metal arc welding (GTAW) 钨极气体保护焊(含氩弧焊)gas turbine generator set 燃气轮发电机组gas turbine power generator燃气轮机发电机gas welding 气焊gasket 垫圈gate valve 闸阀geophysical survey vessel 物探船girders and webs 水平桁材和垂直桁材girth weld 环缝global positioning system (GPS) 全球定位系统globe valve (normally closed) 截止阀(常闭) Glycerin 甘油Gouging 气刨graphite crucible 石墨坩埚grating 格栅gravity damper 重力风闸gravity platform 重力式平台gravity type foundation 重力式基础Grease 黄油, 润滑油Grind 打磨Grinder 砂轮机Grinding 打磨(名词)grinding machine 砂轮机grit 磨料grit blasting 喷丸除锈Groove 熔池groove angle 坡口角guard filter 保护滤器guide funnel 导向喇叭口guide structure 导向结构Gusset 节点板、筋板guyed tower platform 拉索塔平台Hhalf nipple 一端带螺纹的接头halogenated hydrocarbon local panel 卤化烃就地控制盘halogenated hydrocarbon cylinder 卤化烃瓶halogenated hydrocarbon fire extinguishing system 卤化烃灭火系统Hammer 锤子hand operated pump 手动泵hand winch 手动缆绳车Handrail 栏杆hard hat 安全帽Hardener 固化剂hauling to the front 牵引至码头前沿hazardous area 危险区heat affected zones (HAZ) 热影响区heat detector 热探测器heat exchanger 热交换器heat medium drain tank 热介质排放罐heat number 炉号heat traced pipeline 伴热管线heat treater 加热器处理器heat treatment 热处理Heater 加热器heater treater 热处理器heater treater feed pump 热处理器供液泵heating medium boiler package 热介质锅炉撬heating medium circulating package热介质循环撬heating medium collection tank 热介质收集罐heating medium diesel daily tank 热介质柴油日用罐heating medium drain pump 热介质排放泵heating medium drain tank 热介质排放罐heating medium expansion vessel 热介质膨胀罐heating medium make-up pump 热介质再启动泵heating medium oil, thermal oil 传热介质油heating medium storage tank 热介质油储存罐heating, ventilation and air conditioning system (HA V) 采暖、通风、空调系统heave wall section 厚壁段heavy can 节点加厚段heavy duty coating 厚层防腐heavy plate 厚板heavy wall pipe 厚壁管helideck 直升机甲板helmet 安全帽、焊接面罩hex head bolt 六角头螺栓high / low pressure switch (PSHL) 高－低压开关high concentration gas alarm 高浓度可燃气报警high pressure condensate tank 高压凝析油罐high pressure flare 高压火炬high pressure separator (HP separator)高压分离器high strength steel 高强度钢high-low 错皮histogram (统计用)直方图hold 待定hold point (检验的)停点holder 焊钳holiday detector 气孔探测仪horizontal distance 水平距离horizontal welding 横焊hose 软管hose assembly 软管总成hose connection 软管接头hose handling crane 软管起升吊机hose reel 软管轮hot dip galvanizing 热浸锌hot water pressure vessel with electric heater 热水压力罐(带加热器)hot work 明火作业H-shapeH型钢human life and property 人民生命财产hydrant 消火栓hydraulic pile-driving hammer 液压打桩锤hydraulic press 液压机hydrostatic/ hydraulic test 水压试验hyperbaric diving system= pressurized diving system 高压潜水系统Iice-breaker 破冰船if (when) necessary 若有必要Ignitor 点火器immersion suit 防寒救生衣impact resistance 耐冲击性impressed-current protectionsystem 外加电流保护系统in accordance with 按照in any jacket plane 在任意导管架平面内in line with 按照in the light of 按照inclined stair 斜梯include but not limited to 包括但不限于included / groove angle 坡口角度inclusion 夹杂物incomplete fusion 未熔合incomplete penetration 未焊透inflatable liferaft 气胀式救生筏inlet gas generator package 惰性气体发生器撬inorganic Zinc primer 无机锌底漆in-process inspection 工序间的检验inside diameter (ID) 内径Inspection 检验inspection criteria 检验标准installation site 安装现场instrument air receiver 仪表空气接受器instrument capillary tube仪表控制管线instrument master control room 仪表总控制室insulating flange 绝缘法兰Insulation 保温insulation (heat traced) 保温加伴热intact / damage stability 完整/破损稳性Interference (杆件之间的)相碰、打架intergranular corrosion 晶间腐蚀intermediate strength steel 中强度钢intermittent welding 断续焊internal and external beveling 内外坡口internal diameter 内径internal quality audits 内部质量审核internal stress 内应力interpass temperature 层间温度intersected pipe 被交管intersection line 相贯线invitation for bid = call for bid 招标JJack 千斤顶Jacket 导管架jacket cap 导管架帽jacket handling 导管架扶正jacket launching and upending导管架下水及扶正jacket launching barge 导管架下水驳船jacket leg 导管架腿柱jacket leveling 导管架调平jacket lifted on and off the barge 吊上及吊下驳船的导管架jacket lifting eye 导管架吊耳jacket modification 导管架改造jacket panel 导管架片jacket panel assembly 导管架片组对jacket positioning 导管架定位jacket securing 导管架固定jacking state 升降状态jacking system 升降系统jack-up rig 自升式钻井船jockey pump 供消防水干管的补给水泵joint can 节点加厚段joint detail 节点详图J-tube J形管junction box (explosion proof)接线箱(防爆型)Kkey plan 总图、索引图killed steel 镇静钢Kingpost 将军柱Llack of fusion 未融合lack of penetration 未焊透Ladder 直梯ladle analysis 熔炼分析lamellar tearing 层状撕裂Lap 焊缝盖面lap welding 搭接焊lateral load 侧向荷载launch / cargo barge 滑道式/装载式驳船launch way and rocker 滑道和摇臂launching and uprighting of a jacket 导管架的下水和直立launching truss 下水珩架lay barge 铺管船lead sections and subsequent add-ons of piles 首桩及后续桩段leak test 密封性试验(试漏)Leg 桩腿、导管leg of a fillet weld (角焊缝)焊角高度Level 水平仪level gauge (with drain) 液位计(带排放)life boat 救生艇life boat davit , davit 吊艇架life buoy 救生圈life jacket 救生衣life raft , life float 救生筏lift calculation 吊装计算lifting gear 吊艇机lifting load 起吊荷载lifting lug 吊点lifting padeye 吊点lifting up of panel structure 单片起吊light type combustible gas detector 轻质可燃气体探测器line pipe 管线管line throwing apparatus 抛绳装置liquid trap 液体捕集器living quarter 生活块LNG carrier, LNG tanker 液化天然气运输船loading arm 输油臂loading flexible hose 柔性装载软管loadout and seafastening 装船固定local deformation 局部变形local stress 局部应力longitudinal seam/weld 纵焊缝low explosion limit (LEL) 爆炸下限low heat input 低热量输入low hydrogen type electrode 低氢型焊条low pressure scrubber 低压气净化器low stress round nosed die stamp低应力圆头钢印lower deck 下甲板lub oil drain tank 润滑油排放罐lub oil tank with heater 润滑油罐(带加热器) Lubricant oil transfer pump 润滑油传输泵Lug 吊耳Mmachinery deck 机械甲板machining 机加工macrosection 宏观断面magnetic particle and suspension 磁粉和悬剂magnetic particle technique (MT) 磁粉探伤main boiler 主锅炉main deck 主甲板main generator set 主发电机组main process line 主要工艺管线main switch room 主变电间main transformer room 主变压器室make-up drawing 造管图Manhole 人孔Manifold 管汇manned platform 驻人平台manual / hand welding 手工焊manufacturer's instruction 产品使用说明marine growth 海生物marine radio system 海事通讯系统marine transportation 海运Marking 做标记、划线marking and cutting 划线下料mat support jack-up rig 沉垫自升式钻井船Material 材质、材料material identification 材料标识material list 材料表material storage 材料储存material substitution 材料代用material take-off 材料估算单material traceability 材料跟踪maximum operating water depth 最大工作水深mean sea level (MSL) 平均海平面mechanical property 机械性能mechanical test 机械性能试验medium pressure separator(MP separator) 中压分离器member 杆件member drawing (杆件的)单件图member number 杆件号metacenter 稳心metal lash 钢板网mezzanine deck 夹层甲板、半甲板middle deck 中甲板mild steel 低碳钢mill 钢厂mill certificate 厂家的材质证书mill scale 钢材出厂时的表面氧化皮mill sheet 制造工艺规程表mineral slag 矿渣miscellaneous items 附件mismatch = high-low 错皮mobile drilling platform / rig 移动式钻井平台mobile radio system 移动式无线电系统model test 模型试验module 撬块、模块mold 模具mold lofting 放样moment 力矩moment of longitudinal inclination 纵倾力矩moment of transverse inclination 横倾力矩moment of inertia 惯性矩mooring bit 系缆柱mooring cable 系泊缆绳mooring dolphin 系缆柱mooring head 系泊头mooring template 系泊基盘mooring yoke 系泊刚臂motor operated valve 电动阀move to yard front 移至码头前沿mud mat 防沉板mudline 泥线multihead metering pump 多头计量泵multipass welding 多层焊multiple lift 多台吊车联合起吊multi-point mooring , spread mooring 多浮筒系泊系统multi-purpose epoxy 多用途环氧漆multi-supported beam 连续梁multi-well template system 多井基盘系统Nnavigation channel 导航灯navigational light 导航灯NC(numerical-control) cutting machine 数控切割机NDT 包括：near white metal 接近金属白色needle valve 针阀Nipple 对丝node can 节点段nominal diameter 公称直径non-combustible 不可燃物质non-conformance 不一致事项nondestructive examination(NDE)无损检验nondestructive testing (NDT) 无损检验nonskid ceramic mosaic 防滑陶瓷马赛克normal practice 通常作法normalize 正火normally open / close valve 常开/常闭阀notch toughness 缺口韧性NRL (Naval Research Laboratory) drop weight test NRL 落锤试验nut 螺母penetrant technique (PT) 渗透检验radiographic technique (RT) 射线探伤magnetic particle technique (MT) 磁粉探伤ultrasonic technique (UT) 超声波探伤visual inspection 外观检验Oobsolete document 作废文件oceanographic research vessel 海洋调查船offshore drilling installation 海上钻井设施offshore drilling rig 海上钻井装置offshore hook-up海上连接offshore installation 海上安装offshore installation site 海上安装现场offshore oil exploration 海洋石油勘探offshore platform 海洋平台offshore structure 海洋结构物oil boom, oil fence 围油栅oil concentration (污水)含油浓度oil depot 油库oil fence reel 围油栅卷筒oil moisture content 油雾含量oil pollution 石油污染oil recovery vessel 污油回收船oil spill 溢油oil storage barge 储油轮oil storage, loading andtransportation equipment储油、装油与输油设备oil treatment facility 油处理设施oily water tank 含油污水仓oily water transfer pump 污油水传送泵one-line diagram 单线图onshore fabrication 陆上预制open drain pump 开式排放泵open drain tank 开式排放罐open drain tank with heater 开式排放罐(带加热器)open firing point 明火点operating condition 作业条件operating state 作业状态operation draft 作业吃水orifice plate 孔板流量计Original原稿out of roundness椭圆度outside diameter (OD) 外径Ovality 椭圆度over coating intervals 复涂间隔over head crane 天车吊Overboard 舷外Overhanging beam 悬臂梁overhead welding 仰脸焊Overlap 焊瘤Overlapping joint 搭接节点Owner 业主Oxyacetylene gas welding 氧－乙炔气焊oxyacetylene welding 氧乙炔焊oxygen cylinder 氧气瓶oxygen hose 氧气带Ppackaged air conditioner 空调机橇块Packer 封隔器Padeye 吊点paint brush 油刷子paint roller 油漆滚子Painter 油漆工panel assembling 平面组对，单片组对parasitic echo 干扰回声parent steel 母材past successful practice 以往成功的作法pedestal crane 基座式吊机pedestal crane 平台用吊机peening 捶击penetrant technique (PT) 渗透检验perimeter 周长periodical survey 定期检验permissible stress 许用应力perpendicularity of pipe end 管端垂直度personnel protection 人身保护phenolic paint 酚醛树脂涂料Philips driver 十字螺丝刀phthalic paint 苯二甲酸涂料pig launcher 清管器发射器pig receiver 清管接收器pile cap 桩帽pile driving records 打桩记录pile driving refusal 拒锤点pile extracting 拔桩pile foundation 桩基pile guide 桩导向pile penetration 桩的贯入度pile section / segment 桩段pile sleeve 桩套筒pile spacer 扶桩间隙块pile washing out 冲桩piling 打桩pilling barge 打桩船pilot house 驾驶室pinhole 针尖状气孔pipe diameter管径pipe fitting 管件pipe rack 管子托架pipe shoe管子支撑、管靴pipe wrench 管钳pipeline 管线、管道pipeline laying barge 铺管船piping and instrument diagram (P & ID)管线仪表图plain end 无螺纹管端plan 平面图、布置图plasma arc cutting (PAC) 等离子弧切割plasma arc welding (PAW) 等离子弧焊接plate girder 板梁plate type heat exchanger 板式换热器platform 平台platform positioning on the site 导管架的现场定位platform-to-shore radio system 平台－海岸无线电系统pliers 钳子plug 丝堵plug valve 旋塞阀plummet 铅坠plus or minus 2 正负2pneumatic binary signal 双向气动信号pneumatic lines 气控管线pneumatic operated valve 气动操作阀pneumatic operated with manualreset valve 手动复位气动阀pneumatic test 气压试验polarization potential (阳极的)极化电位polarized steel 极化铁polyurethane paint 聚氨酯涂料porosity 密集气孔port 左舷port hole 舷窗portable extinguisher 手提式灭火器portable two-way radio 双向无线电话positioner 定位器positioning 定位positive displacement flow meter 容积式流量计positive flow meter 正位流量计postweld heat treatment 焊后热处理pot life (油漆的)混合期效power wire brush 电动钢丝刷preheat temperature 预热温度preheater 预热器pressure differential flow meter差压流量计pressure gauge 压力表pressure regulation valve 压力调节阀pressure regulator (external tap) 压力调节阀(阀外引压)pressure relief valve 压力释放阀pressure safety valve 压力安全阀pressure vessels 压力容器primary structural member 主结构杆probe 探头procedure qualification record (PQR) 焊接工艺评定process 工序process drain 工艺排放process module 工艺模块product identification andtraceability 产品标识和跟踪production manifold 生产管汇production platform 生产平台production process and equipment 生产工艺及设备production shutdown panel (PSDP) 应急系统关断盘production welding 生产性焊接professional skill 专业技能protractor 量角器provision 条款、规定、措施punch marks 冲眼punch list 遗留工作清单punching shear 冲剪应力purchase 采购purchase order number 订货合同号purge/pilot gas package 吹扫/引燃器橇块Qquality assurance 质量保证quality audit 质量审核quality awareness 质量意识quality check in process 工作中自检quality control (QC) 质量控制quality evaluation 质量评估quality loop 质量环quality manual 质量手册quality objectives 质量目标quality plan 质量计划quality planning 质量策划quality policy 质量方针quality related costs 质量成本quality review/assessment 质量评审quality surveillance 质量监督quality system 质量体系quasi-static loading 准静力荷载quay 码头quenched and tempered steel 淬火加回火钢。

海洋工程专业英语

一词汇(be)subject to…经受…(in) duplicate 一分两式(to be) buttered (焊接的)长肉(to) drive piles 打桩4:1 taperd transition bevel 四比一过渡坡口A resulting formB 由B导致AA-60 fire door A-60级防火门abrasive （喷砂用的）磨料abrasive paper 砂纸AC generator 交流发电机AC motor 交流发动机accelerated corrosion testing 加速腐蚀试验acceptance criteria 合格准则access hole(for welding) =cope hole （焊接）工艺孔accommodation and power platform(APP) 生活动力平台according to=in accordance with=in line with =as per =in the light of 按照acetylene gas 乙炔acid electrode 酸性焊条acid proof cement 防酸水泥additive 添加剂adhere to 遵守（动词）adherence to 遵守（名词）adjacent columns 相邻立柱adverse combination of loads 荷载的不利组合adverse condition 不利条件aeronautical radio system航空无线电AFC(approved for construction) 建造批准aforementioned 上述的aft winch 船艉绞车agitator 搅拌器a-hundred-year return period 百年一遇air blower 鼓风机air compressor 空压机air driven pump 气动泵air hoister 气动绞车air manifold 气包air tight test 气密性试验aircraft obstruction beacon 航空障碍灯air-hose 风带alarm buzzer 报警蜂鸣器alarm horn 报警喇叭aliphatic polyurethanel 脂肪族聚氨脂漆allowable(working)stress 许用应力Aluminum alloy anode 铝合金阳极Aluminum ingot 铝锭aluminum paint 银粉漆aluminum sheet 铝皮ambient air temperature 环境气度ambient temperature 环境温度anchor block 地锚块anchor bolt 地脚螺拴anchor ground 锚地anchor pile 锚桩anchor profile/pattern 涂桩表面的粗糙度anchor rack 锚架anchoring buoy 锚泊浮筒angle of incidence 入射角angle of reflection 折射角angle probe method超声波斜射探伤angle steel 角钢angle valve 角阀anode core 阳极芯子anode end face geometry 阳极端面几何形状anode life 阳极寿命anode potential 阳极电位anode stand-off post 支架式阳极的立柱anodic resistance 阳极电阻anticorrosive paint 防锈漆anti-electrostatic floor 防静电地板antipollution measures 防污染措施API specified requirements API规定的要求apparent batter 视斜度applicable API specification API适用范围approach-departure sector 直升飞机起落扇行区appurtenance =attachment =accessory =auxiliary 附件arc air gouging 碳弧气刨arc cutting 电弧切割arc strike 弧击argon arc welding 氩弧焊argon arc welding machine 氩弧焊机articulated tower mooring system 铰接塔系泊系统artificial island 人工岛as per 按照as-built 完工as-built dossier 完工资料as-built drawing 完工图as-built drawing 完工图as-rolled 轧制状态assemble 组装(动词)assembly 组装(名词)associated gas 伴生气at the option of A 按A的意愿Atmospheric diving system =unpressurized diving system 常压潜水系统atmospheric vent 放空管attachments 附件auto fire alarm system 火灾自动报警系统automatic spraying system 自动喷淋系统back chipping 清根back gouging 反面气刨backing weld 打底焊道backpressure regulator (self contained) 背压式调节阀(自力式)backwash return pump 反冲洗回流泵backwash surge tank 反冲洗罐backwash tank 反冲洗水罐Ball hardness 布式硬度ball valve 球阀bar (截面较小的)圆钢方钢六角钢等bar chart 统计用的柱状图barge bumper 靠船件barge strength and stability 驳船强度及稳性barrel (管件的)加厚段base metal 母材、基本金属basic design 基本设计basic drawing 基本设计图basic electrode =lime type covered electrode 碱性焊条battery room 蓄电池间beam depth 梁高beam path distance 超声波发射程距bearing strength of the ground 地基承载力bearing stress 支撑应力before welding is initiated 始焊前bending moment 弯矩bending stress 弯曲应力bevel 坡口bevel angle 坡口面角度beveling/chamfering 开坡口bid / tender for …投标bid ddrawing 招标图纸bid drawing 招标图纸bilge / fire pump 舱底污水-消防两用泵bilge alarm system污水报警系统blast cleaning喷砂除锈blind flange 盲法兰blind spectacle flange 快速盲法兰blow count 打桩的锤击数blow out preventer system(BOP system) 防喷器系统blowdown vessel 排放罐blowhole;gas pore 气空blowout preventer stack 防喷器组boat landing 登船平台bolt,nut and washer 螺栓、螺母及垫片bolted connection 螺栓连接boom 吊机扒杆boom angle 吊臂倾斜角bore hole 镗孔boss with plug 带有丝堵的管座bottom echo 底面回声bottom sitting drilling platform 坐底式钻井船boundary condition 边界条件bow 船艏box beam 箱形梁box type joinnt 箱形节点brace 拉筋bracelet anode 手镯式阳极branch member 支杆breathing apparatus , respirator 防毒面具bridge 栈桥bridge (overhead) crane 天车吊brittleness 脆性brush coating 用毛刷涂漆buckle fastener 绑带build-up girder 组合梁bulb angle 球扁钢bulk head 隔板，舱壁buoyant turret mooring 浮筒转塔式系泊burn through 烧穿burner 气焊工burr and flashing 飞边毛刺business and management 经营管理butterfly valve 蝶阀butt-welded seam 对接焊缝cable layer 敷缆船cable rack / tray 电缆托架caisson 沉箱caisson washing pump 洗船泵caisson-type platform 沉箱式平台can （管件的）段cantilever beam 悬臂梁cantilever jack-up rig 悬臂自升式钻井船cantilever well module 悬臂式井口模块cap beam 帽梁capped steel 半镇静钢capsizing lever 倾覆力臂capsizing moment = overturn moment 倾覆力矩carbon arc air gouging 碳弧气刨carbon dioxide cylinder 二氧化碳气瓶carbon equivalent 碳当量carbon-dioxide(CO2) arc welding 二氧化碳气体保护电弧焊cargo master system 货油舱总监控系统cargo tank cleaning machine 洗舱机carrier （搬运）小车carry out = perform = conduct =execute 进行、执行catenary anchor leg mooring(CALM) 悬链锚腿系泊cathodic protection 阴极保护cellar deck 底甲板cellar shutdown panel(CSDP) 井口系统关断盘cement grout 水泥浆cementing vessel 固井船center line 中心线center of buoyancy 浮心center of floatation 漂心center of gravity 重心center punch 冲子central control room(CCR) 中央控制室central processing platform 中心处理平台centrifugal pump 离心泵ceramic tiles 瓷砖certifying authority 第三方检验机构chain block 倒链chair with arm-rests 带扶手的半软椅chamfering 开坡口channel steel 槽钢charpy-V notch energy 夏比V形缺口韧性值charpy-V notch impact test 夏比V形缺口冲击试验chart datum 海图基准面chemical injection package 化学注入撬chemical injection system 化学药剂注入系统chemical seal 化学密封chipping hammer 敲渣锤chisel 风铲chord member 弦杆Christmas tree 采油树circumference 周长circumferential weld 环焊缝classification survey 入级检验clean water injection pump 清水注入泵clean water surge tank 清水缓冲罐coefficient 系数cold formed pipe 冷卷管cold shut 冷隔cold work 冷加工、冷作collapse ring 加强环板column 立柱combustible gs detector 可燃气体探测器come-along 手搬葫芦commercial blast cleaning 普通级喷砂除锈commissioning 调试compile and maintain a document 编制和保存文件complete penetration groove weld 全熔透坡口焊completion riser 完井立管complex with 符合（名词）comply with 符合（动词）composite rockwool ceiling复合岩棉天花板composite rockwool panel复合岩棉板concentric reducer同心大小头conceptual design 概念设计cone 大小口、锥体conform to = stick to = adhere to符合、遵守connection 节点、连接consumption rate 阳极消耗率continuous beam 连续梁continuous double fillet weld双面连续贴角焊continuous weldings连续焊contract合同contraction stress收缩应力contractor 承包商contractor（合同供方）control valve (accessories handwheel) 带手轮的控制阀control valve assembly 控制阀总成coordinates 坐标系coordination 协调cope hole （焊接）工艺孔corrective and preventive action 纠正和预防措施correlation curve 相关曲线corrosion allowance 腐蚀余量corrosion coupon 腐蚀挂片corrosion protection 防腐corrugated plate interceptor 斜板分离器couplant UT用的耦合剂coupling 连轴器、管箍crack 裂纹crane barge,crane vessel起重机crane support吊机支撑crater 焊口crawler crane履带吊车criteria（验收）标准cross angle 交叉角cross section横截面crow bar撬杆cruciform bollard 单十字带缆柱crude cooler 原油冷却器cup support 垫墩curing time （油漆的）固化时间current capacity （阳极的）电流容量current density（阳极的）电流密度current direction 海流方向curvature radius 曲率半径customer (比较purchaser) 客户（签合同后，客户变需方）cut by torch 以火焰切割cut off 割除、割除物cutoff allowance 切割裕量cutting plan 排版图cutting sheet单件图DAC curves 距离-振幅曲线daily diesel filter日用柴油滤器damage_prone connection 易破坏的节点damper , dampener 减振器DC generator 直流发电机ddry chemical extinguisher 干粉式灭火器Decibel (dB) 分贝deck beam 甲板梁deck cover 甲板敷料deck crane 甲板吊车deck floor plate 甲板板deck water seal unit甲板水封装置deep freeze compressor 深冷压缩机deepwater jacket 深水导管架defect /default /disconnection 缺陷deflection 挠度dehydration degassing vessel 脱水除气器dehydration preheater脱水预热器dehydrator feed pump电脱水供给泵delivery of materials 材料交货derrick barge 回转式起重船desander 除砂罐design basis 设计基准design drawing详细设计图design parameters 设计参数detail 详图detail design详细设计develop /establish a document编制文件dew point露点DFT(dry film thickness) 干膜厚度diagonal brace 斜拉筋dial gauge 百分表diaphragm 隔板diaphragm valve隔膜阀die stamp 钢印diesel filter coalescer 柴油过滤净化装置diesel generator set柴油发动机diesel oil daily tank with heater 柴油日用罐（带加热器）diesel pump 柴油泵diesel storage tank with heater 柴油储罐（带加热器）diesel storage tank 柴油储罐diesel tank 柴油罐diesel transfer pump 柴油输送泵differential pressure control valve 差压控制阀diffuser 布风器dihedral angle 二面角dimensional checks 尺寸校验direct /alternating current arc welding 直/交流电弧焊direct current emergency supply直流应急电源disassembling拆除discontinuity缺陷displacement oil tank 置换油罐distortion from welding 焊接变形distress signals 遇险呼救信号diver 潜水员diver support vessel潜水作业船document approval and issue 文件的批准和下发documentation文件编制dog 组装用的刀把dolphin 系缆柱domestic sea water pump 生活海水泵double agent facility 双介质灭火装置double bevel groove K形坡口double bollard 双柱带缆柱double groove 双面坡口double plate 垫板、包板double probe method 双探头法doulbe bed 双层床doulbe V groove 双面V形坡口（X形坡口）down hill welding 下向焊drain pit 排水池draught gauge 吃水标尺drawing and specification 图纸及技术规格书drawing types 图纸种类dredger 挖泥船drift pin 心轴、销子drift test 管流试验、管线试通drill 钻头drilling module 钻井模块drilling platform 钻井平台drilling template 钻井基盘drillship ,drilling ship 浮式钻井船driving voltage 驱动电压dryer 烘箱dry-type tree 干式采油树during the course of fabrication 在制造过程中during the life of structures 结构寿命期间dye penetrant inspection 着色检验dynamic-positioning rig 动力定位钻井船earth lead 地线eccentric reducer 偏心大小头echo height 回波高度edge crimping （卷管的）压头edge preparation 坡口加工effective throat thickness 焊缝计算厚度elbow 弯头electric dehydrator 电脱水器electric desalter 电脱盐器electric drill 手电钻electric heater 电加热器electric submersible pump 电潜泵electrical connection 导电连接electric-hydraulic valve 电-液操作阀electrochemical property 电化学特性electrode 电焊条electrode covering 焊条药皮electrode holder 焊把、焊钳electrolyte 电解质electro-slag welding 电渣焊接elevation(EL) 标高、立面图elongation 延伸率emergency air compressor 应急空压机emergency ballast control system 应急压载控制系统emergency BOP recovery system 防喷器紧急回收系统emergency generator 应急发电机emergency light 应急照明灯emergency power station 应急电站emergency shutdown 紧急关断emergency shutdown system(ESD) 应急关断系统emergency switch board 应急开关柜emergency switch room 应急配电间emery cloth 金刚砂布emulsion transfer pump 乳化油输送泵engine room 动力舱、机舱engineering geotechnical vessel 工程地质船engineering vessel 工程船舶entire length 全长equal angle 等边角钢equation 公式equipment base 设备底座erection 安装ERW(electric resistance welding) 电阻焊escape route 逃生路线essential variable 焊接基本参数excess of weight 超重existing structure 已有结构explosion proof equipment 防暴设备exposure distance 防火距离extent of defect in % 缺陷百分率extent of inspection 检验范围extent of repair 返修率external surfaceof brace 拉筋的外表面extra margin of stress 应力裕量fabricated wide flange shape 焊接成的宽翼缘型钢fabrication aids 制造辅助物（如临时吊点）fabrication design 加工设计fabrication drawing 加工设计图fabrication phase 制造阶段fabrication sequence 制造顺序fabrication yard 制造场地face bend test 表面弯曲试验facsimile transceiver 传真收发两用机fastener 紧固件fatigue damage 疲劳破坏field assembly 空间组队、现场组对field mating point 海上对接点（如导管架与组块对接点）field splice 现场拼接field weld 现场焊缝fiexed platform 固定式平台fiexed tower SPM 塔系泊fifty year return period 五十年一遇file 锉刀filler metal 填充金属final fabrication tolerance 最终制造公差finish coat 面漆first coat 底漆finished product 成品finite element analyses 有限元分析fire alarm siren 火灾警笛fire and gs detecting system 火灾-可燃气探测系统fire control panel 消防控制盘fire damper 防火风闸fire door closer,fire proof door 防火门fire extinguishing system 消防系统fire fighting water, fire water 消防水fire foam hadrant 消防泡沫拴fire hose station ,hose box 消防箱fire monitor 消防炮fire panel 火灾-可燃气报警显示盘fire proof wall ,fire wall 防火墙fire protected plastic tiles 防火塑料地板fire protection wall 防火墙fire station 消防软管箱fire waater hose rock 消防水软管fire water deluge system 大水量灭火系统fire water hydrant 消防水拴fire water jockey pump 消防水增压泵fire water lift pump 消防水提升泵fire water pump 消防水泵fire water/foam monitor 消防炮（水或泡沫）fire-fighting vessel ,fire boat 消防船fireman box 消防员箱first aid kit 急救箱first stage hydrocyclone 一级水力旋转器first stage separator 一级分离器fitter 组装工fit-up 坡口组对fixed crude oil washing machine 固定式原油清洗机fixed drilling platform 固定式钻井平台flame arrester 阻火器flame cutting 火焰切割flame cutting droplets and debris 火焰切割形成的熔滴和料头flame cutting machine 火焰切割机flame cutting torch 火焰割枪flammability limits 可燃度极限flange 冀缘、法兰flare assembly 火炬总成flare boom 火炬臂flare drum 闪蒸罐flare pilot gas 火炬引燃器flare scrubber 火炬分液器flare tower 火炬塔flat bar 扁钢flat plate anode 扁阳极flat position / downhand welding 平焊flat wekding 平焊flaw 裂纹flaw detectability 缺陷检测灵敏度flaw echo 缺陷回声flexible hose 柔性软管flexible riser 挠性立管floater controlled valve 浮球控制阀floating cargo hose浮式输油软管floating loading hose浮式装油软管floating oil production and storage unit(FPSU)浮式生产储油装置floating oil storage unit 浮式储油装置floating production ,storage and off-loading tanker 浮式生产储油外输轮floating production platform 浮式生产平台floating state 漂浮状态flooding 注水floppy disk 软盘flow chart 流程图flow indicator(FI) 流量显示器flow quantity recorder(FQ) 累计流量计flow swith 流量开关flux 焊药flux cored arc welding(FCAW) 药芯焊flux-cored electrode 管状焊条flux-cored wire 药芯焊丝foam extinguishing system 固定式泡沫灭火系统foam monitor 泡沫炮foam station 泡沫站fog horn ,fog signal 雾笛folding bed 折叠床folding chair 折叠椅foot print 被交位置foot valve 底阀forecastle 艏楼foreman 领班forged steel(FS) 锻钢fork lift 铲车，叉车forming 压制成型forming of plates into tubular 由板卷成管formula /equation of carbon equivalent 碳当量公式four way valve 四通阀fracture toughness 断裂韧性frame structure 梁格结构free water knockout vessel 流离水分离器fresh water pressure vessel 淡水压力罐fresh water pump 淡水泵fresh water tank pump 淡水罐fresh water tank with electric heater 淡水罐（带加热器）friction coefficient 摩擦系数fuel gas compressor packge 燃气压缩机撬fuel gas heater 燃料气加热器fuel gas scrubber 燃气洗涤器fuel gas treatment package燃料气处理撬fuel oil drain tank燃料油排放罐fuel pump 燃油泵full coupling 全螺纹的接头full penetration weld 全溶透焊缝funnel-shaped guide喇叭口状导向furnace熔炉、加热炉fusible plug 异熔塞fusion/bond line 熔合线gantry crane 龙门吊gap gauge 间隙尺gas bottle 气瓶gas cutting 气割gas cutting machine with magnetic wheels 磁轮式气割机gas detector 可燃气体探测器gas injection module 注气组块gas metal arc welding 熔化极气体保护焊gas metal arc welding (GMAW) 熔化极气体保护焊gas tungsten metal arc welding (GTAW) 钨极气体保护焊gas tungsten metal arc welding (GTAW) 钨极气体保护焊（含氩弧焊）gas turbine generator set 燃汽轮机发电机组gas turbine power generator 燃汽轮机发电机gas welding 气焊gasket 垫圈gate valve 闸阀geophysical survey vessel 物探船girders and webs 水平绗材和垂直绗材girth weld 环缝global positioning system (GPS) 全球定位系统globe valve (normally clsoed) 截止阀（常闭）glycerin 甘油gouging 气刨graphite crucible 石墨坩埚grating 格栅gravity damper 重力风闸gravity platform 重力式平台gravity type foundation 重力式基础grease 黄油、润滑油grind 打磨grinder 砂轮机grinding 打磨（名词）grinding machine 砂轮机grit 石英砂grit blasting 喷丸除锈groove 熔池groove angle 坡口角ground flush 磨平gs export facility天然气外输设备guard filter 保护滤器guide funnel 导向喇叭口guide structure 导向结构gusset 节点板、筋板guyed tower platform拉索塔平台half nipple 一端带螺纹的接头halogenated hydrocarbon cylinder 卤化烃瓶halogenated hydrocarbon cylinder local panel 卤化烃就地控制盘halogenated hydrocarbon cylinder local panel 卤化烃就地控制盘halogenated hydrocarbon fire extinguishing system 卤化烃灭火系统hammer 锤子hand operated pump 手动泵hand winch 手动缆绳车handrail 栏杆hard hat 安全帽hardener 固化剂hauling to the front 牵引至码头前沿hazardous area 危险区heat affected zones(HAZ) 热影响区heat detector 热探测器heat exchanger 热交换气heat medium drain tank 热介质排放罐heat number 炉号heat traced pipeline 伴热管线heat treater 加热热处理器heat treatment 热处理heater 加热器heater treater 热处理器heater treater feed pump 热处理器供热泵heating medium boiler package 热介质锅炉撬heating medium circulating package 热介质循环撬heating medium collection tank 热介质收集罐heating medium diesel daily tank 热介质从柴油日用罐heating medium drain pump 热介质排放泵heating medium drain tank 热介质排放罐heating medium expansion vessel 热介质膨胀罐heating medium make-up pump 热介质再启动泵heating medium oil , thermal oil 传热介质油heating medium storage tank 传热介质油储存罐heating,ventilation and air conditioning system(HAV) 采暖、通风、空调系统heave wall section 厚壁段heavy can 节点加厚段heavy duty coating 厚层防腐heavy plate 厚板heavy wall pipe 厚壁管helideck 直升机甲板high pressure separator(HP separator) 高压分离器high strength steel 高强度钢high-low 错皮histogram （统计用）直方图hold 待定hold point （检验的）停点holder 焊钳holiday detector 气孔探测仪horizontal distance 水平距离horizontal position welding 横焊horizontal welding横焊hose 软管hose assembly 软管总成hose connection 软管接头hose handling crane软管起升吊机hose reel 软管轮hot dip galvanizing热浸锌hot water pressure vessel with electric heater 热水压力罐（带加热器）hot work 明火作业H-shape H型钢human life and property 人民生命财产hydrant 消火栓hydraulic pile_driving hammer 液压打桩锤impact resistance 耐冲击性impressed-current protection system 外加电流保护系统in accordance with 按照in any jacket plane 在任意导管架平面内in line with 按照in the light of 按照inclined stair 斜梯include but not limited to 包括但不限于included /groove angle 坡口角度inclusion 夹杂物incomplete fusion 未熔合incomplete penetration 未焊透inflatable liferaft气胀式救生筏inlet gas generator package 惰性气体发生器撬inorganic Zine primer 无机锌底漆in-process inspection 工序间的检验inside diameter(ID) 内径instrument master control room 仪表总控制室insulating flange 绝缘法兰insulation 保温insulation(heat traced) 保温加伴热intact / damage stability interference 完整/破损稳性（杆件之间的）相碰，打架intergranular corrosion 晶间腐蚀intermediate strength steel 中强度钢intermittent welding 断续焊internal and external beveling 内外坡口internal diameter 内径internal quality audits 内部质量审核internal stress 内应力interpass temperature 层间温度intersected pipe 被交管intersection line 相贯线invitation for bid =call for bid 招标jack 千斤顶jacket 导管架jacket cap 导管架帽jacket handling 导管架扶正jacket launching and upending 导管架下水及竖立jacket launching barge 导管架下水驳船jacket leg 导管架腿柱jacket leveling 导管架调平jacket lifted on and off the barge 吊上及吊下驳船的导管架jacket lifting eye 导管架吊耳jacket modification 导管架改造jacking state 升降状态jacking system 升降系统jack-up rig 自压式钻井船jockey pump 供消防水干管的补给水泵joint can 节点加厚joint detail 节点详图J-tube J形管junction box(explosion proof) 接线箱（防暴型）key plan 总图、索引图killed steel 镇静钢kingpost 将军柱lack of fusion 未融合lack of penetration 未焊透launch way and rocker 滑道和摇臂launching and uprighting of a jacket 导管架的下水和直立launching truss 下水珩架lay barge 铺管船lead sections and subsequent add-ons of piles 首桩及后续桩段leak test 密封性试验（试漏）leg 桩腿、导管leg of a fillet weld （角焊缝）焊角高度level 水平仪level gauge (with drain) 液位仪（带排放）life boat 救生艇life boat davit ,davit 吊艇架life buoy 救生圈life jacket 救生衣light type combustible gas detector 轻质可燃气体探测器line pipe 管线管line throwing apparatus 抛绳装置liquid trap 液体捕集器living quarter 生活块LNG carrier ,LNG tanker 液化天然气运输船loading arm 输油臂loading flexible hose 柔性装载软管loadout and seafastening 装船固定local deformation 局部变形local stress 局部应力longitudinal seam / weld 纵焊缝low explosion limit(LEL) 爆炸下限low heat input 底热量输入low hydrogen type electrode 底氢型焊条low pressure scrubber 底压气净化器low stress round nosed die stamp 底应力圆头钢印lower deck 下甲板lub oil drain tank 润滑油排放罐lub oil tank with heater 润滑油罐（带加热器）main generator set 主发电机组main process line 主要工艺管线main switch room 主变电间main transformer room 主变压器室make-up drawing 造管图manhole 人孔manifold 管汇manned platform 驻人平台manual / hand welding 手工焊manufacture's instruction 产品使用说明marine growth 海生物marine radio system 海事通讯系统material substitution 材料代用material take off 材料估算单material traceability 材料跟踪maximun iperating water depth 最大工作水深may 可以（任意性的）mean sea level(MSL) 平均海平面mechanical property 机械性能mechanical test 机械性能试验medium pressure separator (MP separator) 中压分离器member 杆件member drawing （杆件的）单件图member number 杆件号metacenter 稳心metal lash 钢板网mezzanine deck 夹层甲板，半甲middle deck 中甲板mild steel 底碳钢mill 钢厂mill certificate 厂家的材质证书mill scale 钢材出厂时的表面氧化皮mill sheet 制造工艺规程表mineral slag 矿渣miscellaneous items 附件mismatch = high-low 错皮mobile drilling platform / rig 移动式钻井平台mobile radio system 移动式无线电系统model test 模型试验module 组块mold 模具mold lofting 放样moment 力矩moment of inertia 惯性矩moment of longitudinal inclination 纵倾力矩moment of transverse inclination 横倾力矩mooring bit 系缆柱mooring cable 系泊缆绳mooring dolphin 系缆柱mooring head 系泊头mooring template 系泊基盘mooring yoke 系泊刚臂motor operated valve 电动阀needle valve 针阀nipple对丝node can接点段nominal diameter公称直径non-combustible不可燃物质non-conformance不一致事项nondestructive examination(NDE) 无损检验nondestructive testing 无损检验nonskid ceramic mosaic 外观检验normal practice 通常作法normalize 正火normally open /close valve 常开／常闭阀notch toughness 缺口韧性NRL(naval research laboratory) drop weight test NRL落锤试验nut 螺母obsolete document 作废文件oceanographic research vessel 海洋调查船offshore drilling installation 海上钻井设备offshore drilling rig 海上钻井装置offshore hook-up 海上连接offshore installation 海上安装offshore installation site 海上安装现场offshore oil exploration 海洋石油勘探offshore platform 海洋平台offshore structure 海洋结构物oil boom, oil fence 围油栅oil concentration （污水）含油浓度oil depot 油库oil fence reel 围油栅卷筒oil moisture content 油雾含量onshore fabrication 陆上预制open drain pump 开式排放泵open drain tank 开式排放罐open drain tank with heater 开式排放罐（带加热器）open firing point 明火点operating condition 作业条件operating state 作业状态operation draft 作业吃水orifice plate 孔板流量计original 原稿out of roundness 椭圆度outside diameter(OD) 外径ovality 椭圆度over coating intervals 复涂间隔over head crane 天车吊overboard 舷外overhanging beam 悬臂梁overhead position welding 仰脸焊overhead welding 仰脸焊overlap 焊瘤packer 封隔器padeye 吊点paint brush 油刷子paint roller 油漆滚子painter 油漆工panel assembling 平面组对，单片组对parasitic echo 干扰回声parent steel 母材past successful practice 以往成功的作法pedestal crane 基座式吊机pedestal crane 平台用吊机peening 捶击penetrant technique 渗透检验polyurethane paint 聚氨酯涂料porosity 密集气孔port 左舷port hole 舷窗portable extinguisher 手提式灭火器portable two-way radio 双向无线电话positioner 定位器positioning 定位positive displacement flow meter 容积式流量计positive flow meter 正位流量计postweld heat treatment 焊后热处理pot life （油漆的）混合期限power wire bruch 电动钢丝刷preheat temperature 预热温度preheater 预热器pressure differential flow meter 差压流量计pressure gauge 压力表pressure regulation valve 压力调节阀pressure regulator(external tap) 压力调节阀（阀外引压）pressure relief valve 压力释放阀pressure safety valve 压力安全阀pressure vessels 压力容器primary structrural member 主结构杆probe 探头procedure qualification record(PQR) 焊接工艺评定process 工序process drain 工艺排放process module 工艺模块product identification and traceability 产品标识和跟踪production manifold 生产管汇production platform 生产平台production process and equipment 生产工艺及设备production shutdown panel(PSDP) 应急系统关断盘production welding 生产性焊接professional skill 专业技能protractor 量角器provision 条款，规定，措施punch marks 冲眼punching shear 冲剪应力purchase 采购purchase order number 订货合同号purge / pilot gas package 吹扫/引燃器撬块quality assurance 质量保证quality audit 质量审核quality awareness 质量意识quality check in process 工作中自检quality control(QC) 质量控制quality evaluation 质量评估quality loop 质量环quality manual 质量手册quality objectives 质量目标quality plan 质量计划quality planing 质量策划quality policy 质量方针quality related costs 质量成本quality review/assessment 质量评审quality surveillance 质量监督quality system 质量体系quasi-static loading 准静力荷载quay 码头quenched and tempered steel 淬火加回火钢quick coupling 快接管箍quick release hook(QRH) 快速解脱钩quiver 焊条筒radial offset of abutting edges of longitudinal weld seam 纵缝对接口的经向错皮radio equipment 无线电设备radio positioning system 无线电定位系统radiographic examination 射线检验radiographic interpretion 射线探伤的评片radiographic technique 射线探伤radiographic technique (RT) 射线探伤radius of operation 作业半经receipt and storage of materials receipt to /dispatch form a warechhouse 材料的接受和储存入/出库receiving inspection 到货检验reciprocating pump 往复泵recommended practice 推荐作法recovered oil tank 回收油罐red lead 红丹reducer 大小头，变经头reducer concentric 同心大小头reducer eccentric 偏心大小头refinery /petrochemical works 炼油/石化厂reinforcement 加强筋rejected or scrapped 拒收或报废relative humidity 相对湿度relaxation of rejection criteria 拒收标准的放宽release=issue =distribution （文件的）发放removable hatch 活动舱盖removable spool piece 可拆短管remove rate 返修率remove rust 除锈repair welding 补焊，返修焊缝rescue boat 救助艇residual stress 残余应力retention of documents 文件的保管review point 审核点revolving derrick barge 全回转式起重船rework 返工rib plate 肋板rigger 组装工人rigger 起重工right angle squaure 直角尺righting moment 回复力矩rimmed steel 沸腾钢ring stiffener 补强用环板riser clamps 立管卡子riser template 立管基盘riveter 铆工rock wool penel 岩棉板rock wool shell （保温用的）岩棉管rockwell hardness 洛氏硬度rod bar 圆钢rod electrode 电焊条rod stub 焊条头rolled shape / section 轧制型钢rolled steel plate 轧制钢板rolled tubular 卷制管roller bearing 滚珠轴承rolling direction （钢板的）轧制方向roll-up support 翻身垫墩root face 坡口的钝边root gap /opening 焊根间隙root run 根部焊道rope reel 缆绳卷筒rotary oil burner 旋转燃烧器rotary pump 旋转泵routine installation 一般性安装ROV(remote operated vehicle) 水下机器人row -up 立片，单片起立rubber gasket 像皮垫run -off tab 熄弧板run-on tab 引弧板sacrificial anode 牺牲阳极sacrificial anode 牺牲阳极saddle 垫墩saddle end 马鞍口safe working load (SWL) 安全工作荷载safety cap 安全帽safety factor 安全系数safety valve 安全阀safety zone 安全区sag 下垂salt spray test 盐水噴雾腐蚀试验salvage vessel 救援船sand blasting 喷砂除锈sand filter unit 砂滤装置sand hopper 喷砂砂罐sand jack 砂墩sandpaper 砂纸satellite navigation system 卫星导航系统satellite platform 卫星平台saturation diving 饱和潜水scaffolding 脚手架scanning speed 扫查速度screw driver 螺丝刀，改锥scriber 划线针s-curve （统计用）S曲线sea chest 海水柜sea current 海流sea state 海况sea water life pump 海水提升泵seafastening /tie down of jeckets （导管架装船的）固定seafloor bearing capacity 海床承载力seal weld 密封焊道seal welding 密封焊seamless pipe 无缝管seawater lift pump 海水提升泵second coating 二遍漆second gas scrubber 二级气体洗涤器second stage hydrocyclone 二级水力旋流器secondary /primary brace 次要/主要拉筋section 剖面图，一段segment 一段self shielded welding 自保护焊self tapping screw 自攻螺丝self weight 自重self-contained pressure regulator 自给式压力调节阀self-elevating drilling platform 自升式钻井船self-inspection 自检semi-automatic welding 半自动焊semifinshed/intermediate product 半成品semisub drilling unit 半潜式钻井装置semisubmersible rig 半潜式钻井船separator/urge vessel 分离/缓冲器serrated 锯齿形service after sales 售后服务sewage treatment unit 生活污水处理装置sewage unit 排污罐shall 必须（强制性的）shape cutting 仿形切隔shape steel 型钢shear stress 剪切应力sheet pile 钢板桩sheet piling 板桩shelf life 油漆的储存期限shielded metal arc welding (SMAW) 手工电弧焊shielded metal arc welding (SMAW）手工电弧焊shim plate 间隙条，导向块shop design 加工设计shop drawing 车间加工图shop drawing 车间加工图shop primer 车间底漆shot blast 噴丸除锈should 应该、最好、宜（建议性的）shower bath 淋浴器shrinkage strains 收缩应变shutdown switch 关断开关shutdown valve 关断阀shuttle tanker 穿梭油轮side bend test 侧弯试验silencer 消音器silver/silver Chloride(Ag/Ag Cl) reference cell 银/氯化银参比电池simple beam 简支梁simple joint 简单节点simply supported beam 简支梁single anchor leg mooring (SALM) 单锚腿系泊single berth with chest and drawers 有柜和抽屉的单人床single buoy mooring (SBM) 单点系泊single groove 单面坡口single point mooring (SPM) 单点系泊single V groove 单面V形坡口site assembly 空间组装，现场组装site installed 现场安装site representative 驻厂代表sit-on bottom stability 坐底稳性sitting on the sea bed 坐底skidded loadout 滑道式装船skip weld 跳焊skirt pile 裙桩skirt plate 裙板skirt sleeve 裙装套筒slag 溶渣slag catcher 捕集器slag inclusion 夹渣slag removal 清渣slate pencil 石笔slide door 滑动门slide down the launch way 沿滑道滑动slide shoe=lunch cradle 滑靴sling 吊索slip way 滑轨slop tank 污油罐slope 坡度slot welding 槽焊slotted member 开槽杆件。

钢结构专业英语_史上最全

12钢结构专业英语史上最全Aacceptable quality 合格质量acceptance lot 验收批量aciera 钢材admixture 外加剂aggregate 骨料air content 含气量air-dried timber 气干arch—shaped roof truss 拱形屋架area of shear plane 剪面面积area of transformed section 换算截面面积assembled monolithic concrete structure 装配整体式混凝土结构automatic welding 自动焊接auxiliary steel bar 架立钢筋Bbackfilling plate 垫板balanced depth of compression zone 界限受压区高度balanced eccentricity 界限偏心距bar splice 钢筋接头bark pocket 夹皮batten plate 缀板beam 次梁bearing plane of notch 齿承压面bearing plate 支承板bearing stiffener 支承加劲肋bent-up steel bar 弯起钢筋block 砌块block masonry 砌块砌体block masonry structure 砌块砌体结构blow hole 气孔board 板材bolt 螺栓bolted connection (钢结构)螺栓连接bolted joint (木结构)螺栓连接bolted steel structure 螺栓连接钢结构bow 顺弯brake member 制动构件brick masonry column 砖砌体柱brick masonry structure 砖砌体结构brick masonry wall 砖砌体墙broad—leaved wood 阔叶树材building structural materials 建筑结构材料building structural unit 建筑结构单元building structure 建筑结构built—up steel column 格构式钢柱bundled tube structure 成束筒结构burn—through 烧穿butt connection 对接butt joint 对接butt weld 对接焊缝Ccalculating area of compression member 受压构件计算面积calculating overturning point 计算倾覆点calculation of load-carrying capacity of member 构件承载能力计算camber of structural member 结构构件起拱cantilever beam 挑梁cap of reinforced concrete column 钢筋混凝土柱帽carbonation of concrete 混凝土碳化cast-in—situ concrete slab column structure 现浇板柱结构cast-in—situ concrete structure 现浇混凝土结构cavitation 孔洞cavity wall 空斗墙cement 水泥cement content 水泥含量cement mortar 水泥砂浆characteriseic value of live load on floor or roof 楼面、屋面活荷载标准值characteristi cvalue o fwindload 风荷载标准值characteristic value of concrete compressive strength混凝土轴心抗压强度标准值characteristic value of concrete tensile strength 混凝土轴心抗拉标准值characteristic value of cubic concrete compressive strength混凝土立方体抗压强度标准值characteristic value of earthquake action 地震作用标准值characteristic value of horizontal crane load 吊车水平荷载标准值characteristic value of masonry strength 砌体强度标准值characteristic value of permanent action· 永久作用标准值characteristic value of snowload 雪荷载标准值characteristic value of strength of steel 钢材强度标准值characteristic value of strength of steel bar 钢筋强度标准值characteristic value of uniformly distributed live load 均布活标载标准值characteristic value of variable action 可变作用标准值characteristic value of vertical crane load 吊车竖向荷载标准值charaeteristic value of material strength 材料强度标准值checking section of log structural member·，原木构件计算截面chimney 烟囱circular double—layer suspended cable 圆形双层悬索circular single—layer suspended cable 圆形单层悬索circumferential weld 环形焊缝classfication for earthquake—resistance of buildings 建筑结构抗震设防类别clear height 净高clincher 扒钉coefficient of equivalent bending moment of eccentrically loaded steel memher(beam-column)钢压弯构件等效弯矩系数cold bend inspection of steelbar 冷弯试验cold drawn bar 冷拉钢筋cold drawn wire 冷拉钢丝cold—formed thin—walled sectionsteel 冷弯薄壁型钢cold-formed thin-walled steel structure 冷弯薄壁型钢结构cold—rolled deformed bar 冷轧带肋钢筋column bracing 柱间支撑combination value of live load on floor or roof 楼面、屋面活荷载组合值compaction 密实度compliance control 合格控制composite brick masonry member 组合砖砌体构件composite floor system 组合楼盖composite floor with profiled steel sheet 压型钢板楼板composite mortar 混合砂浆composite roof truss 组合屋架compostle member 组合构件compound stirrup 复合箍筋compression member with large eccentricity· 大偏心受压构件compression member with small eccentricity· 小偏心受压构件compressive strength at an angle with slope of grain 斜纹承压强度compressive strength perpendicular to grain 横纹承压强度concentration of plastic deformation 塑性变形集中conceptual earthquake—resistant design 建筑抗震概念设计concrete 混凝土concrete column 混凝土柱concrete consistence 混凝土稠度concrete floded—plate structure 混凝土折板结构concrete foundation 混凝土基础concrete mix ratio 混凝土配合比concrete wall 混凝土墙concrete-filled steel tubular member 钢管混凝土构件conifer 针叶树材coniferous wood 针叶树材connecting plate 连接板connection 连接connections of steel structure 钢结构连接connections of timber structure 木结构连接consistency of mortar 砂浆稠度constant cross—section column 等截面柱construction and examination concentrated load 施工和检修集中荷载continuous weld 连续焊缝core area of section 截面核芯面积core tube supported structure 核心筒悬挂结构corrosion of steel bar 钢筋锈蚀coupled wall 连肢墙coupler 连接器coupling wall—beam 连梁coupling wall—column... 墙肢coursing degree of mortar 砂浆分层度cover plate 盖板covered electrode 焊条crack 裂缝crack resistance 抗裂度crack width 裂缝宽度crane girder 吊车梁crane load 吊车荷载creep of concrete 混凝土徐变crook 横弯cross beam 井字梁cup 翘弯curved support 弧形支座cylindrical brick arch 砖筒拱Ddecay 腐朽decay prevention of timber structure 木结构防腐defect in timber 木材缺陷deformation analysis 变形验算degree of gravity vertical for structure or structural member 结构构件垂直度degree of gravity vertical forwall surface 墙面垂直度degree of plainness for structural memer 构件平整度degree of plainness for wall surface 墙面平整度depth of compression zone 受压区高度depth of neutral axis 中和轴高度depth of notch 齿深design of building structures 建筑结构设计design value of earthquake-resistant strength of materials 材料抗震强度设计值design value of load—carrying capacity of members 构件承载能力设计值designations 0f steel 钢材牌号designvalue of material strength 材料强度设计值destructive test 破损试验detailing reintorcement 构造配筋detailing requirements 构造要求diamonding 菱形变形diaphragm 横隔板dimensional errors 尺寸偏差distribution factor of snow pressure 屋面积雪分布系数dogspike 扒钉double component concrete column 双肢柱dowelled joint 销连接down-stayed composite beam 下撑式组合粱ductile frame 延性框架dynamic design 动态设计Eearthquake-resistant design 抗震设计earthquake-resistant detailing requirements 抗震构造要求effective area of fillet weld 角焊缝有效面积effective depth of section 截面有效高度effective diameter of bolt or high-strength bolt 螺栓(或高强度螺栓)有效直径effective height 计算高度effective length 计算长度effective length of fillet weld 角焊缝有效计算长度effective length of nail 钉有效长度effective span 计算跨度effective supporting length at end of beam 梁端有效支承长度effective thickness of fillet weld 角焊缝有效厚度elastic analysis scheme 弹性方案elastic foundation beam 弹性地基梁elastic foundation plate 弹性地基板elastically supported continuous girder 弹性支座连续梁elasticity modulus of materials 材料弹性模量elongation rate 伸长率embeded parts 预埋件enhanced coefficient of local bearing strength of materials 局部抗压强度提高系数entrapped air 含气量equilibrium moisture content 平衡含水率equivalent slenderness ratio 换算长细比equivalent uniformly distributed live load 等效均布活荷载etlectlve cross—section area of high-strength bolt 高强度螺栓的有效截面积ettectlve cross—section area of bolt 螺栓有效截面面积euler's critical load 欧拉临界力euler's critical stress 欧拉临界应力excessive penetration 塌陷Ffiber concrete 纤维混凝仁filler plate 填板门fillet weld 角焊缝final setting time 终凝时间finger joint 指接fired common brick 烧结普通砖fish eye 白点fish—belly beam 角腹式梁fissure 裂缝flexible connection 柔性连接flexural rigidity of section 截面弯曲刚度flexural stiffness of member 构件抗弯刚度floor plate 楼板floor system 楼盖four sides(edges)supported plate 四边支承板frame structure 框架结构frame tube structure 单框筒结构frame tube structure 框架—简体结构frame with sidesway 有侧移框架frame without sidesway 无侧移框架frange plate 翼缘板friction coefficient of masonry 砌体摩擦系数full degree of mortar at bed joint 砂浆饱满度function of acceptance 验收函数Ggang nail plate joint 钉板连接glue used for structural timberg 木结构用胶glued joint 胶合接头glued laminated timber 层板胶合木glued laminated timber structure 层板胶合结构grider 主梁grip 夹具grith weld 环形焊缝groove 坡口gusset plate 节点板Hhanger 吊环hanging steel bar 吊筋heartwood 心材heat tempering bar 热处理钢筋height variation factor of wind pressure 风压高度变化系数heliral weld 螺旋形僻缝high—strength bolt 高强度螺栓high—strength bolt with large hexagon bea 大六角头高强度螺栓high—strength bolted bearing type join 承压型高强度螺栓连接，high—strength bolted connection 高强度螺栓连接high—strength bolted friction—type joint 摩擦型高强度螺栓连接high—strength holted steel slsteel structure 高强螺栓连接钢结构hinge support 铰轴支座hinged connection 铰接hlngeless arch 无铰拱hollow brick 空心砖hollow ratio of masonry unit 块体空心率honeycomb 蜂窝hook 弯钩hoop 箍筋hot—rolled deformed bar 热轧带肋钢筋hot—rolled plain bar 热轧光圆钢筋hot-rolled section steel 热轧型钢hunched beam 加腋梁Iimpact toughness 冲击韧性impermeability 抗渗性inclined section 斜截面inclined stirrup 斜向箍筋incomplete tusion 未溶合incomplete penetration 未焊透incompletely filled groove 未焊满indented wire 刻痕钢丝influence coefficient for load—bearing capacity of compression member 受压构件承载能力影响系数influence coefficient for spacial action 空间性能影响系数initial control 初步控制insect prevention of timber structure 木结构防虫inspection for properties of glue used in structural member 结构用胶性能检验inspection for properties of masnory units 块体性能检验inspection for properties of mortar 砂浆性能检验inspection for properties of steelbar 钢筋性能检验integral prefabricated prestressed concrete slab—column structure 整体预应力板柱结构intermediate stiffener 中间加劲肋intermittent weld 断续焊缝Jjoint of reinforcement 钢筋接头Kkey joint 键连接knot 节子(木节)。

钢结构专业英语

钢结构设计专用术语1．1结构术语1 焊接钢结构welded steel structure以手工电弧焊接或自动、半自动埋弧焊接作为连接手段并用金属焊条、焊丝作为连接材料，将钢结构和部件连接成整体的结构。

2 铆接钢结构riveted steel structure以铆钉作为连接件将钢结构或部件连接成整体的结构。

3 螺栓连接钢结构bolted steel structure以普通螺栓作为连接件将钢结构或部件连接成整体的结构。

4 高强螺栓连接钢结构high-strength boltec steel structure以高强螺栓作为连接件将钢结构件或部件连接成整体的结构。

5 冷弯薄壁型钢结构cold-formed thin-walled steel structure以冷弯薄壁型钢作为主要材料所制成的结构。

6 钢管结构steel tubular structure以圆钢管或方钢管或矩形钢管作为主要材料制成的结构7 预应力钢结构prestressed steel structure通过张拉高强度钢丝束或钢绞线等手段或调整支座等方法，再钢结构构件或结构体系内建立预加应力的结构。

1.2 构件、部件术语1 实腹式钢柱solid-web steel column腹板为整体的竖向受压钢构件2格构式钢柱built-up steel column;laced or battened compression member由钢缀才将各分肢组成整体的竖向受压钢构件。

分双肢，三肢和四肢格构式钢柱3分离式钢柱separated steel column支承屋盖的竖向刚肢体和支承吊车梁的竖向刚肢体两者用水平钢板连接而成整体的双肢受压钢构件。

4 缀才(缀件) lacing and batten elements在格构式受压钢构件中用以连接肢体并承受剪力的腹杆。

分缀条和缀板4.1缀条lacing bar在格构式受压钢构件中用以连接肢体并承受剪力的条状腹杆缀板batten plate5 钢柱分肢steel column compnent组成格构式钢柱或分离式钢柱的竖向肢体6钢柱脚steel column base扩大钢柱底端与基础相连接的加强部分。

钢结构专业英语词汇

Accelerate 促进剂Accelerator硬化剂，接触剂Acetic acid 醋酸Acetone 丙酮Achromatic color 无彩色Acid stain 丙烯酸树脂Acrylic丙烯酸Acrylics acid resin 丙烯酸（类）树脂Acrylonitrile butadiene styrene resin ABS树脂，丙烯腈-丁二烯-苯乙烯树脂Active agent 活性剂Additive 添加剂Additive mixture 加色混合Adhesive 胶粘剂Adhesive solvent 胶（料）溶剂Adjacent color 类似色Advancing color 进出色Aerosol spraying 简易喷涂After image 残象Air drying 常温干燥Airless spraying 无气喷涂Alcohol stain 酒精着色剂Alert color警戒色Alkyd resin 醇酸树脂Alligatoring 漆膜龟裂Amount of spread 涂胶量Anticorrosive paint 防锈涂料Antifouling paint 防污涂料Antique finish 古式涂料Automatic spraying 自动喷涂BBaking finish 烤漆喷涂Base boat 底漆Blistering 小泡Blushing 白化Body varnish 磨光漆Brilliant 鲜艳的Brushing 刷涂Brushing mark/streak 刷痕Bubbling 气泡Button lac 精致虫胶Café 咖啡色Carbamide resin adhesive 尿素树脂胶Catalyst 催化剂，触媒，接触剂Chalking 粉化Cherry 樱桃色Chipping 剥落Chromatic color 有彩色Chromaticity 色度Chromaticity coordinates 色度坐标Chromaticity diagram色度圆Clssing 补漆Clear coating 透明涂层Clear lacquer 透明喷漆Clear paint 透明涂料Coarse particle 粗粒Coating 涂料Cobwebbing 裂痕Cocos 可可色Cold water paint 水性涂料Color blindness 色盲Color conditioning 色彩调节Color harmony 色彩调和Color in oil 片种特（调色用）Color matching 调色Color number 色号（色之编号或代号）Color paint 有色涂料Color reaction 显色反应Color reproduction 色重现Color tolerance 色容许差Compatibility 相容性Complimentary color 补色Consistency 稠厚度Contractive color 收缩色Col color 寒色，冷色Cooling agent 冷却剂Covering power 覆盖力Cracking 龟裂，裂纹Cresol resin adhesive 甲酚树脂胶Crimping 皱纹Cure 硬化Curing agent 固化剂Curing temperature 固化温度Dark 暗Deep 深Degumming 脱胶Dewaxed shellac 胶蜡虫胶Diluent 稀释剂，冲淡剂Dilution ratio 稀释比例Dingy 浊色Dipping 浸渍涂层Dipping treatment 变色Discoloring 变色Discord 不调和色Drier 干燥剂Dry rubbing 干磨Drying time 干燥时间Dulling 失光Dusting 粉化EEgg-shell 埴孔亚光，显孔亚光electrostatic spraying 静电涂装emulsion adhesive 乳化胶emulsion paint 乳化涂料enamel 色漆，磁漆end-coating 端面涂层end-gluing 端面胶合epoxy finish环氧效果epoxy resin glue环氧树脂胶ethyl cellulose lacquer乙基纤维素喷漆FFading退色Filler 腻子，埴料，填充剂Finish code 涂料编号Finshing 涂饰Flaking 剥落Flat paint 消光涂料Flatness 消光Floor paint 地板涂料Foam glue 泡沫胶GGelatin 明胶，凝胶Glare 眩目Glue 胶粘剂，胶，胶料Glue and filler bond 动物胶及填料胶结Glue mixer 调胶机Glue spreader 涂胶机Gum 树胶，胶树HHardener 硬化剂Hide 皮胶High solid lacquer 高固体分漆Honey color 蜂蜜色IIlluminant color 光源色JJelly strength 胶质强度Joint strength 胶接强度LLac 虫胶Lac varnish 光漆Lacquer 漆Latex 乳胶Latex paint 合成树脂乳化型涂料Leveling agent 均化剂Light 光亮的Liquid glue 液态胶Long oil varnish 长性清漆Love formaldehyde 低甲醛MMake up paint 调和漆Medium oil varnish 中油度清漆Melamine resin adhesive 三聚氯胺树脂胶，蜜胺树脂胶Melamine resin sheet 三聚氯胺树脂（片）Methyl alcohol 甲醛Multi-color 多彩漆NNatural clear lacquer 清漆N.C lacquer 硝化棉喷漆N.C lacquer enamel 硝色棉色漆N.C lacquer sealer硝化棉底涂料N.C lacquer surfacer 梢化棉中涂整面涂料Nitro-cellulose lacquer 硝化纤维漆，硝基榉Nitro-lacquer 硝基漆Nitrocellulose lacquer 硝化纤维（喷）漆Non toxix finishes无毒喷漆Novolac （线型）酚醛清漆OOff- color 变色的，退色的，不标准的颜色Oil paint 油性漆Oil putty 油性腻子Oil solvent 油溶剂Oil stain 油性着色剂Oil staining 油着色Oil stone 油石Oil varnish 油性清漆，上清漆Opacity 不透明度Opaque paint 不透明涂料PPaint 涂料，油漆Paint film 涂膜Paint nozzle 涂料喷头Penetrant 渗透剂Phenol aldehyde resin 酚醛树脂胶Polishing varish 擦光（亮）清漆Poly Urethane Resin 聚氨酯（PU）Poly ester 聚酯Polyester resin lacquer 聚酯树脂涂料Polypropylene 聚丙烯Polystyrene聚苯乙烯Polyurethane 聚氨酯Polyvinyl acetate adhesive 聚醋酸乙烯（树脂）胶Polyvinyl adhesive 聚乙烯树脂胶Polyvinyl chloride resin 聚乙烯树脂涂层Pre-coating 预涂Procuring 预固化Preservative 防腐剂Primer 底漆（下涂涂料）Putty 腻子Pyroxylin lacquer 硝基漆QQuick drying paint 速干漆RReady mixed paint 调和漆Refined shellac 精制虫胶Resin adhesive 树脂胶Reverse coater 反向涂料器Roller brush 滚筒刷SSample board 样板Sand blast 喷砂Sand pa。

1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。

海洋钢结构制造专业英语词汇大全
海洋钢结构制造涉及到许多专业英语词汇，以下是一些相关的词汇大全：
1. Marine: 海洋的。

2. Steel structure: 钢结构。

3. Manufacturing: 制造。

4. Offshore: 近海的。

5. Platform: 平台。

6. Subsea: 水下的。

7. Welding: 焊接。

8. Fabrication: 制作。

9. Corrosion protection: 防腐保护。

10. Structural integrity: 结构完整性。

11. Load-bearing capacity: 承载能力。

12. Seawater resistant: 耐海水的。

13. Installation: 安装。

14. Maintenance: 维护。

15. Quality control: 质量控制。

16. Steel plate: 钢板。

17. Pile driving: 打桩。

18. Underwater welding: 水下焊接。

19. Marine engineering: 海洋工程。

20. Oil and gas industry: 石油和天然气行业。

以上这些词汇可以帮助你更好地理解海洋钢结构制造领域的相关内容。

希望对你有所帮助！。