酸轧常用英语词汇(新)

合集下载

酸轧生产线英语

collapse 破裂，断裂；崩溃；折叠；收缩
collapsed mandrel 收缩（状态的）卷筒
coolant n. 冷冻剂, 冷却液, 散热剂
coolant guard 冷却剂挡板；挡油板
coolant jet 冷却剂喷嘴
coupling 耦合，匹配；联轴节；
Back wash(ing) 反冲洗
Back wash filter 反冲洗过滤
Band cutter 手动剪
Barrel [压]辊身
Barrel diameter 辊身直径
Barrel hardness 辊身硬度
Barrel length 辊身长度
Bearing carrier 轴承架，支架
Bearing chock 轴承座
Bearing support 轴承支架
Bearing Lubrication System 轴承润滑系统
Belt Wrappers 皮带助卷器；
Blow off device 吹扫装置
Coil car 上卷小车
Coil Turner 钢卷旋转装置，旋转台
Coil Opener 开卷器
Coil Weighing Scale 钢卷称重装置
（the）continuous pickling line and tandem
cold mill(PL——TCM) 连续酸洗轧制
润滑系统
Grease Lubricating System 油脂润滑系统
Grease Lubrication System 干油润滑系统
H
Hold-down 压紧，压边；压紧装置
Hold-down cylinder 压紧缸

轧钢专业词汇表

轧钢专业词汇表一、首钢京唐（酸轧机组）常用词1.entry W/B conveyor 入口步进梁运输机2. entry coil turner 旋转台3.entry coil car 入口钢卷车4.pay off reel 开卷机5.processor 处理器6.coll opener 开卷器7.ertry shear with pinch roll 入口剪带夹送辊8.scrap disposal equipment 废料处理装置9.deflector pinch roll 转向夹送辊10. deflector roll 转向辊11.welder 焊机12.notcher 月牙剪13.side guide 边部对中14.bridle roll 张力辊15.steering roll 纠偏辊16.tension meter roll 张力计辊17.tension leveller 拉伸破磷机18.entry wringer roll 入口挤干辊19.dryer 干燥器20.side notcher 月牙剪21.hold down roll 压辊22.side trimmer 切边剪23.scrap chopper 碎边剪24.scrap conveyor 废料运输带25.burr masher 去毛刺机l 轧机2l motor 轧机主电机28.rotary shear 飞剪29.carrousel reel 张力卷取机30.inspection table 检查台31.sleeve bucket transfer car 套筒运输车32.delivery coil conveyor 出口步进梁运输机33.skid 鞍座34.nozzle 喷嘴二、浙江东南1. Reversing Cold Mill RCM 可逆式冷轧机2. Motor Control Center MCC 电机控制中心3. E-house 电器室4. transformer 变压器5. skin pass mill 或temper mill 平整机6. product mix 产品大纲7.coil weight 卷重8. stack weight 垛重9. workbase 炉台10. Specific coil weight 卷材单重11. inner cover 内罩12. heating bell 加热罩13. cooling bell 冷却罩14. filter mesh 过滤器网15. pressure switch 压力开关16. isolating unit 隔离装置17. control relay 控制继电器18. emulsion room 乳化液站19. combustion 燃烧20. butterfly valve 蝶形阀21. Safety Equipment 安全设备22. roll chock 轴承座23. Spraying header 喷淋水管（喷淋头）24. Mill stand piping 轧机机座管系管线25. Drive spindles 驱动轴26. Cross cut shear 横剪机组27. Pivot 枢轴28. Coil car 卷材移动台车29. Segments （胀缩式卷筒）扇形体30. Snubber roll 缓冲辊31. Groove 凹槽32. flange 法兰33. Shape Measuring Roll 板形仪34. Delivery entryTension Reel 出入口卷取机35. Foundation Bolts and Nuts 基础螺栓36. Interconnecting piping 中间管线37. Gear Coupling 齿轮联轴器38. Load test 负载测试39. Breakage 断带40. Stoppage 停车cold rolled: 冷轧的冷态滚压的coating section:涂镀断面cold rolled steel sheet: 冷轧薄钢板welding: 焊接cold rolled coil : 冷轧薄卷scale breaker: 除鳞机铁皮清除机electrical steel sheet: 电工钢（片）heat treating furnace: 热处理炉uncoiler: 开卷机minimize spangle: 微化晶粒reheating furnace: 再加热炉coating bath: 镀槽cold leveling: 冷平整，冷矫正air cooling: 空气冷却pickling: 酸洗water cooling: 水冷却cold rolling mill: 冷轧机leveling: 矫正平整electrolytic cleaner: 电解清洗液Hot-dip galvanized steel strip: 热浸镀锌钢preheating: 预热带（卷）soaking cooling: 均匀退热Electrolytic cleaning：电解处理rapid cooling: 快速冷却Electrolytic cleaner：电解清洗液over aging: 过时效老化过度final cooling: 最后冷却reheating furnace：重热熔炉continuous annealing line：连续退火线crack：裂化recoiling：重绕temper rolling：斜坡轧制，硬化冷轧表面temper rolling: 硬化冷轧表面光轧平整光轧平整batch annealing line: 成批退火线Coil preparation line：成卷预热线cold rolled coil: 冷轧薄板Over aging ：过时效老化过度side trimming: 切侧边final cooling：最后冷却shearing line: 剪切线tandam cold rolling：拉锯冷轧cold rolled sheet: 冷轧薄板Trimmer 切边机pay off reel：松卷机Skinpass：表皮光轧shearer：剪切机剪断机delivery looper：传送活套entry looper: 进口活套BP coil：镀锡原板tension leveler：张力平整机Heating area:加热区Furnace：加热炉Bend：弯曲Gas：煤气Combust：燃烧Mixed gas：混合煤气Temperature：温度Nitrogen：氮气Centigrade degree：摄氏度Oxygen：氧气Pyrometer ：高温计Resident oxygen：炉内残氧Thermocouples：热电偶Pressure：压力Fixed beam：固定梁Vol ume：体积、流量Walking beam：步进梁Valve ：阀门Forward：向前Slab：板坯Backward：向后Slab yard：板坯库Discard：剔除Continuous cast slab：连铸板坯Discard table：剔除辊道Width：宽度Charge：装炉Thickness：厚度Discharge：出炉Length：长度Preheating zone：预热区Weight：重量Heating one：加热区Soaking zone：均热区Discharge machine：出钢机Vaporizing cooling/ vapor cooling：气化冷Compressed air 压缩空气却Burner 烧嘴Soft water：软水Combustion air fan 助燃风机Scale：氧化铁皮Recuperative 有恢复力的Ventilate：通风heat exchanger 回热式热交换器Chimney：烟囱Refractory brick 耐火砖Exhaust：废气Mathematic model 数学模型Stack：烟道Feed-forward 前馈Roller able：辊道Feedback 反馈Baffle：挡板Furnace pressure 炉压Charge machine：装钢机Temperature profile 温度曲线Hot rolling shop：热轧车间Mill 轧机Spindle 接轴4-high finishing mill 四辊精轧机Universal Spindle 万向接轴Rough mill 粗轧Shaft 轴Screw down 压下Roll changing device 换辊装置Screw up 抬升辊缝Crane 行车Edger 立辊轧机，轧边机Bite 咬入High-pressure descaling system 高压水除Cascade speed adjustment 串联调速鳞系统Cobble 堆钢事故，中间事故坯料Nozzle 喷嘴Tension 张力Heat cover 保温罩Tension control 张力控制Shear 剪机Loop height 活套量/活套高度Hydraulic loop 液压活套Speed up 升速Looper 活套Lock cylinder 锁紧缸Side guide 侧导卫Balance cylinder 平衡缸Interstand cooling 机架间冷却Lift 提升Run-out table 精轧输出辊道Shift 横移Laminar cooling 层流冷却Leveling 校平，调平Head water tank 高位水箱Zero 校零Side stripper 侧喷头Alignment 对中Pinch roll 夹送辊Industrial water 循环水Down Coiler 卷取机Water volume 水量Mandrel 卷取机芯轴Water pressure水压Wrapper roller 助卷辊Cooling r ate 冷却速度Coil stripper car 卸卷小车Speed cone 速度锥Strip catcher 卷取区域带钢拦截装置Maintenance 检修，维护Gear motor 齿轮马达Pneumatic system 气动系统Coupling 接手，连接器Roll shop 轧辊间Roll 轧辊Work roll 工作辊Grinder 磨床Back-up roll 支撑辊Work roll grinder 工作辊磨床Barrel 辊身Combinative/universal grinder 组合磨床Roll neck 辊颈Roll cooling 轧辊冷却Vertical 垂直的Work roll chock 工作辊轴承座Calibration 校准，刻度Work roll bending system 工作辊弯辊系统Compensation 补偿Work roll shifting system 工作辊窜辊系统Correction 纠正Back-up roll chock 支撑辊轴承座Control panel 控制面板，操作控制台Bearing 轴承Deviation 偏差Work roll bearing 工作辊轴承Error 误差，错误Oil film bearing/morgoil bearing 油膜轴承Offset 偏差量Headstock 头架Definition 定义Tailstock 尾架Reverse 反转Grinding carriage 磨头滑架Swivel 回转，转动Wheel 砂轮Distance 距离Dressing diamond 修整金刚石Range 范围Measure 测量Chamfer 凸度Diameter 直径Centerline 中心线Ovality 不圆度Infeed mode 进给模式Roundness 圆度Limit 限制，极限Eccentricity 偏心度Limit switch 限位开关Contour 外形轮廓Scan 扫描Geometry 几何尺寸，几何形状Coolant 冷却剂Curve 曲线Surface 表面Sine curve 正弦曲线Plunge grinding 掏沟磨削Active curve 实际曲线Caliper 测量卡规Rated curve 额定曲线/设定的曲线Optimize 优化Position 位置Load roll 装辊Axis 轴，数轴Unload roll 卸辊Horizontal 水平的Calibrate caliper 校准测量卡规Finishing area 精整区域Coil marking machine 钢卷标号机Walking beam transfer 步进梁运输机Coil strapping machine 钢卷打捆机Coil yard 钢卷库Coil weighing device 钢卷称重装置Skin pass 平整机Sampling shear 取样剪Saddle 鞍座Transfer chain 链条运输机Electric room 电气室Motor 电机Process computer 过程计算机Main motor 主电机Program 程序，编程Load 载荷PLC：programmable logic controller 可编Over load 过载程控制器Motor load 电机负荷Encoder 编码器Rolling force 轧制力Information 信息Rolling speed 轧制速度Ghost rolling 模拟轧制MPM: meter per minute 米/分钟Measuring instrument 测量仪表Torque 扭矩X-ray X 射线Rated torque 额定扭矩Thickness gauge 测厚仪Voltage 电压Width gauge 测宽仪HMD: hot material detector 热金属探测仪Emergency 紧急，急停CMD: cold material detector 冷金属探测仪Joggle 点动Light barrier 光栅HMI：human machine interface 人机界面Automatic model 自动模式AC frequency converter 交流变频器Semi-auto model 半自动模式I/O：input/output 输入/输出端口Manual model 手动模式Step control 卷取机助卷辊的“踏步”控制Hydraulic system 液压系统Grease 甘油Pump 泵Oil station 油站Screw pump 螺杆泵SSC: Short stroke control 短行程控制Filter 过滤器，滤网AGC: automatic gauge control 自动压下Cylinder 液压缸，圆柱体控制Valve stand 阀台AWC: automatic width control 自动宽度Accumulator 蓄能器控制Leakage 泄漏Product 产品Grade 钢种Ferrite 铁素体Batch 一炉，一批Pearlite 珠光体Batch No. 炉批号Deep drawn 深冲Coil 钢卷SPHC 普通级热轧钢板（卷）Strip 带钢，薄带钢SPHD 深冲级热轧钢板（卷）Sheet 钢板，薄钢板SPCC 普通级冷轧钢板（卷）Plate 中厚板SPCD 深冲级冷轧钢板（卷Physical performance 物理性能High strength low-alloy steel 低合金高强Mechanical performance 机械性能度钢Strength 强度Silicon steel 硅钢，电工钢Elongation 延伸Galvanizing 镀锌Flatness 平直度Coating 涂镀，涂层Plasticity 塑性Heat treatment 热处理Crown/chamber 凸度Aging 时效处理Hardness 硬度Annealing 退火Microstructure 微观组织结构Quenching 淬火Austenite 奥氏体Alarm 报警Radioactive hazard 放射性伤害Anchoring bolt 地脚螺栓Caution 注意，小心Yield 产量，成材率Layout 平面布置Ton 吨Document 文件Annual 一年的Documentation 技术文本，技术文件报价Shift 班书Safety 安全TOP: take-over poi n t 交接点耐磨性abrasive碰撞仪butt gauge气孔abscess计算calculation横坐标abscissa凸轮cam容纳、收纳accommodating曲线度cambering amount空气喷射air ejection辊型误差cambering profile气动电机air motor悬梁cantilever自动踏步控制AJCautomatic jumping有能力的capablecontrol能力capacity定中心、对中align渗碳carburized排成直线、列队、对中alignment小车，砂轮架carriage交替、轮流alternate延伸辊道carry over table电流量amperage连铸坯分段剪CC shear锚固、地脚anchor中心线centerline退火的annealed离心机centrifuge一年一次的annual房间chamber能应用的、适用的、适合的applicable 轴承座chock应用application垫板choke liner增多，重视appreciateC 形沟C-hook接近、进给approach溜槽chute适合的、特有的appropriate圆周运动circular motion裙板apron过滤设备clean-up device相变arrest间隙clearance装配、组装、配件assembly废钢收集装置cobble catcher分配assignment带卷打捆机coil banding machine奥氏体austenite带卷运输机coil conveyor奥氏体轧制austenite rolling带卷检查线coil inspection line 奥氏体的austenitic带卷提升机coil lifter辅助液压auxiliary hydraulic托卷臂coil loading arm轴向的axial带卷打号机coil marking machine 后退、退回backlash开卷机coil opener平衡力balance force带卷鞍座coil saddle球面丝杆ball jack screw带卷鞍座coil skid包装带分配器banding dispenser 带卷站coil station打捆带banding strap卸卷小车coil stripper car冷却段bank带卷回转台coil turner轴承架bearing bracket带卷称重装置coil weighter轴承箱bearing ca.。

轧钢生产必备英语词汇

轧钢生产必备英语词汇整理版4-high finishing mill 四辊精轧机abrasive耐磨性abscess气孔abscissa横坐标AC frequency converter 交流变频器accommodating容纳、收纳Accumulator 蓄能器Active curve 实际曲线AGC: automatic gauge control 自动压下控制Aging 时效处理air ejection空气喷射air motor气动电机AJC=automatic jumping control自动踏步控制Alarm 报警Alignment 对中alignment排成直线、列队、对中align定中心、对中Alloy Construction Steel合金结构钢Alloy Tool Steel合金工具钢alternate交替、轮流amperage电流量Anchoring bolt 地脚螺栓anchor锚固、地脚annealed退火的Annealing 退火Annual 一年的annual一年一次的applicable能应用的、适用的、适合的application应用appreciate增多，重视approach接近、进给appropriate适合的、特有的apron裙板arrest相变assembly装配、组装、配件assignment分配austenite rolling奥氏体轧制Austenite 奥氏体austenite奥氏体austenitic奥氏体的Automatic model 自动模式auxiliary hydraulic辅助液压AWC: automatic width control 自动宽度控制axial轴向的Axis 轴，数轴backlash后退、退回Back-up roll chock 支撑辊轴承座Back-up roll 支撑辊Backward 向后Baffle 挡板Balance cylinder 平衡缸balance force平衡力ball jack screw球面丝杆banding dispenser包装带分配器banding strap打捆带bank冷却段Barrel 辊身Basic Pig Iron炼钢生铁Batch No. 炉批号Batch 一炉，一批bearing bracket轴承架bearing cage轴承箱bearing chock轴承座bearing shoes轴承滑块，托瓦Bearing Steel轴承钢Bearing 轴承Bend 弯曲Billet,Bloom钢坯Bite 咬入Boiler Tube锅炉管bore口径、钻孔bracket支架、托架brittle脆性bronze青铜bucket水桶，废品箱buggy四轮小车Burner 烧嘴bushing衬板butt gauge碰撞仪calculation计算Calibrate caliper 校准测量卡规Calibration 校准，刻度Caliper 测量卡规cambering amount曲线度cambering profile辊型误差cam凸轮cantilever悬梁capable有能力的capacity能力Carbon Construction Steel碳素结构钢Carbon Tool Steel碳素工具钢carburized渗碳carriage小车，砂轮架carry over table延伸辊道Cascade speed adjustment 节联调速Cast Iron Pipe铸铁管Caution 注意，小心CC shear连铸坯分段剪Centerline 中心线centerline中心线Centigrade degree 摄氏度centrifuge离心机chamber房间Chamfer 凸度Channel槽钢Charge machine 装钢机Charge 装炉Chimney 烟囱chock轴承座choke liner垫板C-hook C形沟chute溜槽circular motion圆周运动clean-up device过滤设备clearance间隙CMD: cold material detector 冷金属探测仪Coating 涂镀，涂层cobble catcher废钢收集装置Cobble 堆钢事故，中间事故坯料coil banding machine带卷打捆机coil conveyor带卷运输机coil inspection line带卷检查线coil lifter带卷提升机coil loading arm托卷臂Coil marking machine 钢卷标号机coil marking machine带卷打号机coil opener开卷机coil saddle带卷鞍座coil skid带卷鞍座coil station带卷站Coil strapping machine 钢卷打捆机Coil stripper car 卸卷小车coil stripper car卸卷小车coil turner带卷回转台Coil weighing device 钢卷称重装置coil weighter带卷称重装置Coil yard 钢卷库coil yard带卷跨Coil 钢卷coiler entry side guide卷取机进口侧导板coiling temperature卷取温度Cold Rolled Steel Sheel or Coil冷轧钢板（卷）collapsed收缩状态collimator校准仪，准直仪Combinative/universal grinder 组合磨床Combust 燃烧Combustion air fan 助燃风机combustion燃烧compensate补偿Compensation 补偿complicate复杂的Compressed air 压缩空气compressed air压缩空气computer data line计算机数据传输线concave凹面conceive构想，认为concept概念concrete水泥，钢筋混凝土condition条件conjunction联接console控制台consortium统一，一致Continuous cast slab 连铸板坯Contour 外形轮廓Control panel 控制面板，操作控制台controller控制器convex profile凸形convex凸面convey输送，运输Coolant 冷却剂Cooling rate 冷却速度cooling water header冷却水管cooling water冷却水Correction 纠正correlation相互作用corrosive腐蚀性的Coupling 接手，连接器cradle roll托辊cradle支架Crane 行车criterion标准，准则critical point临界点cross pin type universal joint十字接头式万向接头Crown/chamber 凸度crystallization结晶cubic立方体的Curve 曲线curve曲线cutting force剪切力cutting speed剪切速度cyclic周期的Cylinder 液压缸，圆柱体cylindricity圆柱度dampen缓冲，减振Day 日decade十年Deep drawn 深冲defect缺陷Definition 定义deflector roll偏转辊deformation resistance变形抗力deformation变形despite不管，危害detector of ultrasonic or eddy current type超声波式涡流探伤仪deteriorate消耗，磨损detrimental不利的，有害的Deviation 偏差Diameter 直径digital positioning sensor数字位置传感器diredt servo valve先导伺服阀Discard table 剔除辊道Discard 剔除Discharge machine 出钢机Discharge 出炉dispersion散乱，分散disregard忽视Distance 距离distinct明显的，不同的distributor分配器Document 文件Documentation 技术文本，技术文件报价书double column type龙门式Down Coiler 卷取机down coiler地下卷取机down ender翻转装置downstream下游的Dressing diamond 修整金刚石Drill Pipe For Oil Field石油钻探杆drum changing hook转鼓更换钩drum转鼓ductile柔性，柔软的ductility延展性，延伸率dull变钝，钝的dynamic balance动平衡dynamic动态的eccentricity ring偏心套eccentricity shaft偏心轴Eccentricity 偏心度Edger 立辊轧机，轧边机elastic material弹性材料Electric room 电气室electro-hydraulic servo control电液伺服控制elevation高度eliminated除去，消除Elongation 延伸Emergency 紧急，急停empiric经验的Encoder 编码器energy能量Equal Angle Steel等边角钢Error 误差，错误essential必要的，必不可少的excel优于，擅长exclusive专有的excursion偏差execute实现Exhaust 废气expand伸展extractor分离（拆卸）装置faceplate面板，花盘feature特点，特征Feedback 后馈/反馈Feed-forward 前馈felt毛毡ferrite rolling铁素体轧钢Ferrite 铁素体ferrite铁素体ferritic铁素体结构fill-in table填充辊道Filter 过滤器，滤网finisher delivery temperature精轧机出口温度finisher entry temperature精轧机进口温度Finishing area 精整区域fissure裂纹Fixed beam 固定梁fixed guide固定导板flange法兰flared shape楔形Flat Steel Bar扁钢flat-face CRT平面液晶显示器Flatness 平直度flaw裂纹flexible dog挠性推爪flexible易弯曲的fluorescent荧光的foot stock尾座Forward 向前foundation bolt地脚螺栓foundry Pig Iron铸造生铁frame框架fully expanded全扩展状态funnel漏斗形Furnace pressure 炉压Furnace 加热炉Galvanized Low Carbon Steel Wire. 镀锌底碳钢丝Galvanized Steel Coil镀锌钢板（卷）Galvanized Welded Pipe镀锌焊管Galvanizing 镀锌Gas 煤气Gear motor 齿轮马达Geometry 几何尺寸，几何形状Ghost rolling 模拟轧制Grade 钢种grade级别，钢种grain晶粒Grease 甘油grease干油Grinder 磨床grinder磨床Grinding carriage 磨头滑架ground磨，打磨guard挡板guide roller导辊guide-liner导板guide导卫guiding apron导向导板gyrating旋转hand wheel手轮hanger钩子Hardness 硬度Hbeam型钢head stock床头head tank system高位水箱系统Head water tank 高位水箱header piping喷水横梁header集水管Headstock 头架Heat cover 保温罩heat holding cover保温罩Heat treatment 热处理Heating area:加热区Heating zone 加热区Heavy Rail重轨high speed strip shear高速飞剪high speed strip threading device高速穿带装置High Speed Tool Steel高速工具钢High Strength Deformed Steel Bar钢筋混凝土用变形钢筋High strength low-alloy steel 低合金高强度钢High-pressure descaling system 高压水除鳞系统hinge绞接hi-rotor高速转动体HMD: hot material detector 热金属探测仪HMI：human machine interface 人机界面hoist起重机hold down roll压紧辊Horizontal 水平的Hot Rolled Steel Coil热轧钢板（卷）Hot rolling shop：热轧车间Hydraulic loop 液压活套Hydraulic system 液压系统I/O：input/output 输入/输出端口Ibeam工字钢Industrial water 循环水Infeed mode 进给模式Information 信息Interstand cooling 机架间冷却Joggle 点动Laminar cooling 层流冷却Layout 平面布置Leakage 泄漏Length 长度Leveling 校平，调平Lift 提升Light barrier 光栅Light Rail轻轨Limit switch 限位开关Limit 限制，极限Load roll 装辊Load 载荷Lock cylinder 锁紧缸Loop height 活套量/活套高度Looper 活套辊Main motor 主电机Maintenance 检修，维护Mandrel 卷取机芯轴Manual model 手动模式Mathematic model 数学模型Measure 测量Measuring instrument 测量仪表Mechanical performance 机械性能Microstructure 微观组织结构Mill 轧机Mixed gas 混合煤气Month 月Motor load 电机负荷Motor 电机MPM: meter per minute 米/分钟Nitrogen 氮气Nozzle 喷嘴Offset 偏差量Oil film bearing/morgoil bearing 油膜轴承Oil station 油站Oil 油，稀油Optimize 优化Ovality 不圆度Over load 过载Oxygen 氧气Pearlite 珠光体Physical performance 物理性能Pinch roll 夹送辊Pipe For Oil Field石油套管Plasticity 塑性Plate 中厚板PLC：programmable logic controller 可编程控制器Plunge grinding 掏沟磨削Pneumatic system 气动系统Position 位置Preheating zone 预热区Pressure Pipe高压管Pressure 压力Process computer 过程计算机Product 产品Program 程序，编程Pump 泵Pyrometer 高温计Quenching 淬火Radioactive hazard 放射性伤害Range 范围Rated curve 额定曲线/设定的曲线Rated torque 额定扭矩Recuperative heat exchanger回热式热交换器Refractory brick 耐火砖Resident oxygen 炉内残氧Reverse 反转Roll changing device 换辊装置Roll cooling 轧辊冷却Roll neck 辊颈Roll shop 轧辊间Roll 轧辊Roller table 辊道Rolling force 轧制力Rolling speed 轧制速度Rough mill 粗轧Round Nails for General Uses普通圆钢钉Round Steel普通圆钢Roundness 圆度Run-out table 精轧输出辊道Saddle 鞍座Safety 安全Sampling shear 取样剪Scale 氧化铁皮Scan 扫描Screw down 压下Screw pump 螺杆泵Screw up 抬升辊缝Seamless Steel Pipe For Geological Drill In地质钻探用管Seamless Steel Pipe无缝钢管Semi-auto model 半自动模式Shaft 轴Shear 剪机Sheet 钢板，薄钢板Shift 班Shift 横移Side guide 侧导卫Side stripper 侧喷头Silicon steel 硅钢，电工钢Sine curve 正玄曲线Size 尺寸Skin pass 平整机Slab yard 板坯库Slab 板坯Soaking zone 均热区Soft water 软水SPCC 普通级冷轧钢板（卷）SPCD 深冲级冷轧钢板（卷Speed cone 速度锥Speed up 升速SPHC 普通级热轧钢板（卷）SPHD 深冲级热轧钢板（卷）Spindle 接轴Spring Steel弹簧钢SSC: Short stroke control 短行程控制Stack 烟道Stainless & Heat Resisting Steel不锈耐热钢Steel Plate中厚钢板Steel Strip钢带Steel Wire For Prestressed Concrete预应力混凝土钢丝Steel Wire Rope钢丝绳Step control 卷取机助卷辊的“踏步”控Stranded Wire钢绞线Strength 强度Strip catcher 卷取区域带钢拦截装置Strip 带钢，薄带钢Surface 表面Swivel 回转，转动Tailstock 尾架Temperature profile 温度曲线Temperature 温度Tension control 张力控制Tension 张力Thermocouples 热电偶Thickness gauge 测厚仪Thickness 厚度Ton 吨TOP: take-over point 交接点Torque 扭矩Transfer chain 链条运输机Tube for High-Pressure Vessel高压气瓶用管Unequal Angle Steelh不等边角钢Universal Spindle 万向接轴Unload roll 卸辊Valve stand 阀台Valve 阀门Vaporizing cooling/ vapor cooling 气化冷却Ventilate 通风Vertical 垂直的Voltage 电压Volume 体积、流量Walking beam transfer 步进梁运输机Walking beam 步进梁Water pressure 水压Water volume 水量Weight 重量Wheel Circle轮筛Wheel Tyre车轮Wheel 砂轮Width gauge 测宽仪Width 宽度Window Sash窗框钢Window Screen窗纱Wire Rod Coil线材Work roll bearing 工作辊轴承Work roll bending system 工作辊弯辊系统Work roll chock 工作辊轴承座Work roll grinder 工作辊磨床Work roll shifting system 工作辊窜辊系统Work roll 工作辊Wrapper roller 助卷辊X-ray X射线Yield 产量，成材率Zero 校零。

轧钢专业英语必备词汇[1]1

(5)轧钢Rolling八辊轧机MKW mill 板坯slab 半连续热带轧机semi-continuous hot-strip mill 薄板sheet 薄板轧机sheet mill 保温炉heat holding furnace 扁锭slab i ngot, slab 扁钢flat bar 不可逆轧机non-reversing mill 步进梁式加热炉walki ng beam type furnace 槽钢channel 车底式加热炉car bottom furnace 车轮轧机railway-wheel mill 车丝机threading machine 成卷coiling 成品包装跨packing bay 初轧机blooming mill 初轧坯翻转装置bloom turnover device 出料拉杆kick-out arm 穿孔机piercing mill 粗轧机rough mill 淬火炉harde ning furnace 搭接炉焊管机lap-welded pipe mill 打包用带钢轧机package mill 打捆机bundle machine 打捆机bundler 打印台stamping station 大型型钢轧机heavy section mill 导辊装置roller guide 地上卷取机up coiler 地下卷取机down coiler 地下卷取机down coiler 地下油库oil cellar 地下运输机t unnel conveyer 叠板轧机pack mill 定径机sizing mill 定心机centering mac hine 镀槽coating bath 镀锡板tinning sheet 镀锡槽tinning bath 镀锡线tinn ing line 镀锌板galvanized sheet 镀锌槽galvanizing bath 镀锌线galvanizin g line 堆储跨storage bay 堆垛机piler 钝化处理passivation 多辊矫直机mu lti-roll straightening machine 方钢square bar 方坯bloom 非连续性轧机no n-continuous rolling mill 飞锯flying saw 干燥台drying station 钢坯, 小方坯billet 钢坯库billet store 钢坯修磨conditioning 高速线材轧机high speed wi re rod mill 高压水除鳞hydraulic jet descaler 工字钢I-bar 工字钢轧机I-bea m mill 工作辊换辊装置work roll changer 工作辊支撑装置work roller suppo rting apparatus 钩式运输机hook transfer 光亮退火炉bright annealing furn ace 轨梁轧机rail-beam section mill 滚筒剪drum type shear 横切机transv ersal shear 厚板heavy plate 厚板轧机heavy plate mill 环形加热炉rotary hearth furnace 换辊小车roll change carriage 荒管, 毛管, 空心坯pierced bi llet, hollow billet 回火炉tempering furnace 回转剪rotary cropping shear 活套loop 活套张紧辊bridle roll 机后输出辊道mill run-out table 机架, 牌坊stand, housing 机架辊breast roll 机前输入辊道mill run-in table 挤压机ex truder 夹送辊deflector pinch roll 加热炉heating furnace 碱槽alkaline bath 剪切跨shear bay 减径机reducing mill 矫直机straightening machine, stra ightening mill 角钢angle steel 揭盖机cover carriage 紧卷tight coil 进料拉杆kick-in arm 浸镀immersion coating 井式炉pit batch type furnace 精轧机finish mill 精整加工线finishing machine 精整跨finishing bay 卷材, 线卷coil 均热炉pit furnace 均热炉跨soaking pit bay 均整机,整径机(管) reeling machine 开卷机, 拆卷机decoiler 开坯机cogging mill 可逆辊道reversing t able 空心坯减径机shell-reducing mill 拉丝机wire-drawing machine 扩径机(管) repiercing machine 冷床cold bed 冷锯cold saw 冷轧板带钢cold rolle d strip 立辊vertical roll 连续式加热炉continuous type furnace 连续酸洗co ntinuous acid-washing 链式运输机chain transfer 磷化处理phosphate treat ment 磷酸phosphoric acid 硫酸sulfurous acid 炉卷机steckel mill炉用卷取机furnace coiler 轮箍轧机tyre mill 内表修磨inside grinding 拧接头机coupling applicator 盘条rod coil 平立(万能)轧机horizontal-vertical (H V) mill 平整机temper machine 破鳞辊descaling roll 破鳞机scale breaker, descaler 切边side crops 切边剪end trimming shear 切头top crops 切头剪end shear 切尾end crops 去刺机deburring machine 热处理heat treat ment 热带轧机hot-strip mill 热镀hot-dip coating 热锯hot saw 热轧板带钢hot rolled strip 乳化液emulsion 森吉米尔轧机Sendzimir mill 上料台架ingo ing skid 深冲薄钢板deep drawing sheet 石油管套管pipe case 收集台coll ecting table 受料辊道receiving table 输出辊道run-out table 输入辊道run-i n table 水力除鳞hydraulic descaler 水压试验机hydraulic pressure tester 酸槽acid bath 酸洗槽pickling bath 酸洗工段pickling department 酸洗机pi ckling machine 酸洗线pickling line 酸洗用酸acid for pickling 甩尾back-en d whip 丝扣保护套thread protector 四机架连续式带钢冷轧机four-stand ten dem cold strip mill 松卷loose coil 碎断剪chopping shear 塔式酸洗机towe r pickler 套管接头pipe coupling 铁皮坑scale pit 通径机drifter 筒式卷取机drum type coiler 涂漆装置painting unit 吐丝机laying head 推钢机, 推杆p usher 拖运机,移送机dragging device 脱脂槽degreasing bath 外表修磨out side grinding 弯辊装置bending-up roll device 万向连轴节universal spindlecoupling 无扭轧机non-twist mill 无损探伤non destoryed test 铣头机cha mfering machine 限动芯棒轧管机retained mandrel pipe mill 硝酸nitric aci d 小型型钢轧机light section mill, merchant bar mill 芯棒式轧管机mandrel mill 型钢, 条钢bar 行星轧机planetary rolling mill 修磨机grinder 压下螺丝screw down 压下装置, 压下机构screwdown 延伸机elongator 硬度试验机hardness tester 油膜轴承oil film lubrication bearing 预精轧机pre-finishing mill 预热炉preheating furnace 圆锭round ingot, round billet 圆钢round b ar 圆盘锯circular saw 运锭车, 翻锭车ingot buggy 运输辊道processing ta ble 再加热炉reheating furnace 轧边机, 立辊轧机edger 轧钢rolling 轧钢车间rolling plant 轧管机设备tube mill equipment 轧辊及辊道roller and tabl e 轧辊压下装置roller press-down device 轧辊轴承座roll bearing chock 轧辊支架roll support 轧机rolling mill 轧机传动装置rolling mill drive devic e 轧机跨mill bay, mill aisle 轧机输出辊道mill delivery table 轧机输入辊道mill approach table 窄带strip 张力减径机(管) tension-reducing machine张力控制tension control 罩式炉bell type furnace 支撑辊back-up roll 中板轧机medium plate mill 中厚板medium plate 中间辊道intermediate table 中型宽带轧机medium wide-strip mill 中型型钢轧机medium section mill 中轧机intermediate mill 周期式轧管机pilger mill 转盘turntable 自动轧管机plug mill 纵切机longitudinal shear, slitting shear。

冷轧词汇

部分词汇整理Cold Rolling Mill Line 冷轧厂High Performance HCL Pickling Line高效盐酸酸洗线Chemical Processing Section化学处理段Mechanical Section机械工艺段Process Section工艺段State of the art先进的State of the art technology先进的技术Pickling line (chemical section)酸洗线（化学段）Concentration of pickling acid酸洗浓度Temperature of pickling acid酸洗温度Diffusion in the strip酸液浸透Boundary Phase界面Rinsing water漂洗水Pickling tank酸洗槽Drain-off chamber排放室Squeegee roll units挤干辊设备Squeegee roll挤干辊Pickling medium酸洗介质Hydrochloric acid盐酸Conventional shallow-tank pickling tank常规浅槽酸洗Turbulence pickling tank 湍流酸洗线Strip Break断带Strip Cleanliness 带钢清洁度初漆层、初漆Primer耐酸衬板Acid proof lining耐磨石质枕块Friction Blocks加热循环槽Heating and Circulation Tank短时间停车Standstill循环槽Circulation Tank/chamber酸雾排放回流管座Sockets for fume exhausting return-flow通气管座Venting Socke溢流管座Overflow Sockets喷淋管Spray tube喷嘴Spray nozzleHeat Exchanger of graphite 石墨换热器Horizontal Centrifugal pump 卧式离心泵Filter 过滤器Pressure pipe 高压配管Discharge pipes 排泄管Acid circulation tank 酸循环槽Steel tank，rubber lining 钢槽，橡胶衬cascade pump 梯流泵steadying tank 稳态罐hot rinsing chamber 热漂洗室cold rinsing chamber 冷漂洗室condensate water 冷凝水per rinsing section 预漂洗段integrated collecting tank 组合式收集槽barrel 辊身chock 轴承座journal 轴颈bearing housing 轴承外圈antifriction bearing 耐磨轴承slide door 移动门roll neck 轧辊轴颈compressed air cylinder 压缩空气缸valve stand 阀座stripdryer 带钢烘烤炉radial flow fan pinion and rack conveyor roll inlet air pipe suction box protective grill steem/air heat exchanger though shaft adjustment device sound absorbing cover for fan fume exhaust system absorption tower exhaust gas concertration droplet separation at stack exit sump pit submerged pump temperature control field instrument sensor and transmitter lever control lever indicator differential pressure transducer pressure indicator transmitte flow meter regenerated acid filtered water dematerialized water conductivity control of condensate conductivity transmitter －converter PH monitoring sensor with indicator spressure monitoring for all pump capacity level sensor isolated double electrodes analog transmitter Tandem Cold Mill（TCM ）steering roll driven snubber roll strip clamping assembly ancillary winch parting shear back－up roll fixed strip guide table base frame thickness gauge mill stand hydraulic gap control cylinder cylinder suspension W.R.离心风机齿轮齿条移送辊进气管进气箱防护格栅蒸汽/空气换热器直通轴调整装置风机隔音罩酸雾洗涤系统吸附塔废气浓度烟囱出口滴液防护罩废水坑潜水泵温度控制现场仪表传感器和变送器液位控制液位计差压变送器压力表变送器流量计再生酸过滤水脱盐水冷凝水导电率控制导电率变送率PH 值传播指示计泵压力监测容量液位传感器绝缘双极模拟变送器冷连轧机纠偏辊传动压下辊带钢夹持装置辅助卷扬分切剪支承辊固定式带钢导板台基础框架测厚仪轧机机架辊缝液压控制缸液压缸悬挂缸工作辊W.R. bearingW.R. chockW.R. changing equipment thrust bearingB.U.R.B.U.R. bearingB.U.R. chock B.U.R.changing equipment Emulsion damming roll wrapping angle pivoting carry －over table pivoting guard shape meter roll blow off device splash guard motor coupling momentW.R. drive splindle splindle carrier pinch roll rotary flying shear tension meter roll deflector roll magnetic belt conveyor carrousel tension reel 工作辊轴承工作辊轴承座工作辊换辊装置止推轴承支承辊支承辊轴承支承辊轴承座支承辊换辊装置乳化液档辊包角摆动输送台摆动导板板型仪吹扫装置防溅导板马达接手力矩工作辊传动主轴主轴机架夹紧辊圆盘剪张力辊转向辊电磁皮带机双卷筒旋转式卷取机宽厚板轧机机械部分abort escape system 紧急逃逸系统abort handle 应急把手abrasion resistant 抗磨的，耐磨的absorption of moisture 吸湿，吸潮abrupt change 急剧变化acceleration ramp 加速斜坡，速度爬升accumulator 活套acid resistant 耐酸的acoustic baffle 声障板(damping，enclosure，panel，barrier)actuator 执行机构air inlet duct 空气入口管道air knife 气刀air pocket 气穴air damper 节气门air cushion 气垫allen key 艾伦内六角扳手amplification factors 放大系数anti－flutter roll 防振辊AOD process 氩氧脱碳法Application software 应用软件approach roller table 输入辊道arithmetic mean value 算术平均值armour plate 护板articulated dummy bar 铰链引锭杆As－build construction drawing 建设竣工图纸asynchronous motor 异步电动机axial runout 轴向跳动accelerated plate cooling equpment 快速冷却装置（ACC ）agitator 搅拌器air cylinder 气缸air pressure tank 空气压力罐anti－rusting coat 防锈涂层apron 挡板，裙板automatic valve 自动阀manual valve 手动阀roller bearing 滚珠轴承backprussure 背压backlash compensation 间隙补偿backstop 托架，止回器backup rolls 支撑辊backup roll assembly 支撑辊装配总成backup roll bending 支撑辊弯曲backup roll change(dismantle)stool 支撑辊更换（分解）托架backup roll cleaning device 支撑辊清洗装置backwash water baffle plate bag filter bag house baling press baling wire ball valve bank of pumps bar coded label bar mill barrel hardness base line battery power supply unit bayonet locking bearing chock bearing clearance bearing extractor bearing end play bearing thrust belt wrapper belt wrapper tucking arm bending stress bifurcatrd launder bleed port block diagram block circuit bogie bloted connection booster pump booster fan bottom bending roller bottom sump bottom-pure ladle bottom－tap ladle bottom－roll motor boundary friction boundary lubrication clyburn spanner cock spanner double spanner double－ended open－jawed spanner double offset ring spanner english spanner hammering spanner hose spanner inner hexagon spanner ratchet spanner brace nut 反冲水回洗水隔板挡板布袋滤器袋滤捕尘室打包机打包钢丝铁丝球阀水泵机组排条形码标签小型轧机棍身硬度基线电池供电机组卡口锁定轴承座轴承余隙轴承提取装置轴承的轴向间隙轴承推力助卷皮带助卷皮带压臂抗弯强度分叉流槽泄放孔框图闭塞电路小车螺旋连接增压泵增压风机下转向弯辊废水坑底流式钢包底部放流钢包下轧辊马达边缘摩擦边缘润滑活扳手旋塞扳手双头螺丝扳双端开口爪形扳手梅花扳手活动扳手单头开口爪形扳手软管扳手内六角扳手棘轮扳手拉紧螺帽漏钢，烧穿breakout。

酸轧常用英语词汇

1. PL（酸洗）Operate panels 操作面板岗位：头部1)walking beam=W/B 步进梁2)conveyor 运输器3)entry 入口4)handing 操作5)lock 锁定6)sequence=SEQ. 序列7)band 捆带8)cancel 退出，取消9)fwd =forword 向前10)bwd =backforword 向后11)cycle 循环12)hp=home position 起始位置13)traverse 来回移动、贯穿14)skid centering 对中15)display 显示16)swing 摆臂17)cradle roll 地辊18)lift 升起19)pay off reel=por 开卷线20)opener 开卷器21)jog 点动22)turner 旋转台，旋转者23)leveler i/m 水平矫直24)transfer car 转运小车25)C/C =coil car钢卷小车26)clock wise=CW. 顺时针27)counter clockwise 逆时针28)direction 方向29)by-pass 旁路，边道30)height 高度31)pressure 压力32)mandrel 卷筒33)collap 收缩34)expand 膨胀35)outboard 外支撑36)snubber roll 压辊、缓冲辊37)protector 保护罩38)detect 检查39)pr.=pressure 压力40)increase 增加41)decrease 减少42)inner diameter 内径43)frame 框架44)wedge 楔形45)intermesh 相互啮合46)processor 处理线，处理器47)levelling roll 矫直辊48)P/R=pinch roll 夹送辊49)deviation 偏差50)lv/r chg dev. =leveler change deviation矫直辊更换偏差51)height 高度52)deflect/pinch roll 转向、夹送辊53)side guide=s/g 侧导板54)knife clearance 剪刃间隙55)hot coil thick. 热轧卷厚度56)scrap 废料57)chute 斜槽58)tilt 倾斜、使倾斜59)apron 挡板60)welder 焊机岗位：拉矫机61)Tension leveler 拉矫机62)S/R=steering roll 纠偏辊63)elongation 延伸率64)wiper 刷子65)device 设备岗位：出口圆盘剪66)side trimmer 圆盘剪67)clearance=CLR 侧间隙(水平间隙)68)lap 垂直间隙69)housing 外罩70)scrap chopper 碎边剪71)burr masher 去毛刺辊72)s/t housing width 圆盘剪宽度73)sensor 传感器74)notcher 冲边剪75)center hold down roll 中心压辊LEVEL1 HMI（一级画面）76)monitor 监控器77)looper 活套78)APC =Auto position control 位置自动控制79)drain 排水80)fume 烟气81)pump 泵82)switch 开关，转换83)MCC 电机控制中心84)ARP =Acid Reprocess 酸再生85)layout 布局86)consumption 消费，耗尽87)inspection 检查88)delivery 传送89)length 长度90)weight 重量91)defect 缺陷92)distance 距离93)notcher 冲边剪94)diameter 直径95)weld 焊接96)steel grade 钢种97)yield point 屈服点98)indication 指示99)bucket 桶、斗100)vector 矢量101)source 源头102)converter 变压器103)winding 缠绕弯曲104)inert 迟钝的105)inverter 变频器106)temperature 温度107)actual 实际的108)dust collect fan 除尘风机109)measure 测量110)area 区域111)angel 角度112)COMP.=compensation 补偿113)pitch 向前114)receive 接受115)manual 手动116)remain length 剩余长度117)rinse 漂洗118)dryer 烘干机119)CYL=cylinder 缸120)tail 尾部121)swing angle 摆角122)scrap box 废料箱123)scrap disposal 废料处理124)hopper 漏斗(原文是hooper) 125)layout 布局126)winger roll 挤干辊127)industrial 工业的128)steam 蒸汽129)scrubber 洗刷者130)treatment facility 处理设备131)observation 观察132)acid picking tank 酸洗槽133)acid 酸134)spray 喷射135)storage 储存136)fresh 新鲜的137)regenerate 回收138)waste water 废水139)gas 气体140)compress 压缩141)hydraulic 液压142)discharge 排出143)fume exhaust 排烟144)stack 烟囱145)scale 规模，比例146)induce 感应147)heater 加热器148)filter 过滤器149)sump 污水坑150)inhibitor 抑制剂151)consumption 消耗152)lubrication 润滑153)remote 远程154)local 就地155)clamp 锁紧156)protector 保护罩157)condensate 冷凝物LEVEL2 HMI（二级画面）158)logging 记录，存入159)trend data 趋势数据160)utility 功效161)summary 摘要，一览162)reject 拒绝，封闭163)release 释放，解锁164)inner dia. 内径165)outer dia. 外径166)preceding process 先前的过程167)regist 登记，注册168)match 匹配169)forward 向前170)backward 向后171)temporary 临时的172)consumption 消耗173)statistical 统计的174)division 分开175)delay 延时，延期176)steel grade 钢种177)current 现在的178)punch 冲孔179)preset 预设定180)allowable 可行的181)bridle roll 张力辊182)looper drum 活套卷扬183)productive 生产率184)target 目标185)information 信息186)refresh 恢复2. TCM（轧机）操作面板（operate panels）187)actual data 实际数据188)mill 轧机189)gauge 测厚仪190)R/F=roll force 轧制力191)tension 张力192)level 水平193)roll gap 辊缝194)tandem jog 组合点动195)adjust 调整196)BWD 向后，FWD 向前197)shutter 安全门198)x-ray x射线199)S/G=side guide 侧导板200)online 在线，offline 离线201)touch 接触202)retract 缩回203)BR=bride roll 张力辊204)shift 移动，改变205)Bender 弯辊206)roll change 换辊207)Dif.R/F 轧制力偏差208)forward slip 前滑值209)IMR 中间辊210)WR 工作辊211)roll gap（AVE）辊缝平均值212)wide 宽213)narrow 窄214)shift 移动，改变215)constant 常量216)decrease 减少217)increase 增加218)C-frame c型框架219)damming roll 挡辊220)raise 上升221)carry-over table 引导板222)coolant 冷却液223)air wiper 空气刷224)cobble guard 防缠导板225)pass line 轧制线226)rocker plate 梯板227)balance 平衡228)cyl.height 液压缸高度229)hyrop master 液压控制系统230)wedge 斜锲231)hook 抓钩232)BUR 支撑辊233)idle run 空转234)spindle spotting 轴定位235)push-puller 推拉车236)side shift 侧移237)clamp 夹紧238)ret /set 释放/夹紧239)FL.PLATE 地板盖240)spindle support 轴支撑241)insert 插入242)indication 指示243)retract 缩回244)splash guard 防溅导板245)shape meter roll 板型辊246)LDV shutter 安全门247)sleeve 套筒248)carrousel 卷取机249)casing angle 转鼓旋转角度250)B/W=belt wrapper 助卷器251)W/B=walk beam 步进梁252)pinch roll 夹送辊253)rotary shear 飞剪254)air purge 空气吹扫255)def.=deflector 导向装置256)TR select 卷筒选择257)lift 上升258)mandrel 卷筒259)snubber roll 缓冲辊，压辊260)safe cage 安全门261)traverse 贯穿262)outboard 支撑263)collap. 收缩264)expand 膨胀265)centering 对中266)turner 旋转台267)bander 打捆机268)inspection 检查站269)sensor 传感器270)bucket 桶，斗LEVEL HMI(一级画面) 271)zeroing 零位272)APC 自动位置控制273)ASC 自动板型控制274)thickness 厚度275)hydraulic 液压276)lubrication 润滑277)drain/fume exhaust 排烟风机278)spray 喷射279)MF=meter flow 秒流量280)BIS. 轧制力前馈281)ATL. 自动张力限制282)RFC(GAP+FGC) 动态变规格283)REC 轧辊偏心控制284)GMS 反馈285)ATR 自动张力调节器286)FF 速度前馈287)FB 速度反馈288)FGC 动态变规格289)ATL 自动张力限制290)delivery 传送291)steering roll 纠偏辊292)def.roll 导向辊293)side shift 侧移294)looper drum 活套卷扬295)celler 地下室296)innet 入口297)reel 卷298)revolution 旋转299)belt 皮带300)tail out 甩尾301)leveling 水平302)grade 钢种303)tandem jog 组合点动304)current 当前的，电流305)deviation 偏差306)scale 比例，测量307)forward slip 前滑308)memorized 记忆、存储309)narrow 窄310)wide 宽311)presence 仪表312)weighter 称重器313)winder 旋转型楼梯314)RSV 传感器315)zero compensation 零位补偿316)range 范围317)selective 精心选择318)Stand-by 备用319)calibration 校准320)gear 齿轮321)centralized 集中的322)grease 油脂323)eliminator 消除器324)drainage 排水325)circulation 流通326)accelerate 加速327)decelerate 减速328)confirmation 确认329)strip break 断带330)exhauster 抽气装置331)overload 过载332)media 滤纸333)over low 溢出334)wash down 清洗335)sprinkler 洒水器336)progress 进程337)charge 补给338)amount 总量339)340)LEVEL2 HMI(二级画面) 341)342)unit tension 单位张力343)draft 初步设计344)pinch roll 夹送辊345)defector roll 导向辊346)surface 表面347)dull roll 毛辊348)bright roll 光辊349)diameter 直径350)crown 凸度351)rough 粗糙度352)shape 形状353)chock 轴承座354)roll type 辊子类型355)rolling time 轧制时间356)product time 生产时间357)reduction 变形量358)refresh 恢复，翻新359)log 记录360)label 标记、标签361)pulpit 操纵台362)electrical 带电的363)utility 功效364)quantity 数量365)tonnage 吨位366)parameter 矢量,参数367)friction 摩擦368)modulus 系数，模数369)adapt 相适应370)back-up 备用，备份371)reject 拒绝，封闭372)release 释放，解锁373)quarter 四分之一374)camber 模型375)arch shape 拱形状376)modification 修改377)schedule 规程表378)flag 旗帜，标示379)sample 样品380)preceding 先前的381)flattener 平整机382)unload 卸货，处理383)withholding 扣留，抑制384)register 登记385)pair 一对，交配386)sticky 粘性的387)crack 断裂388)shell 剥皮389)skin 皮肤，剥皮390)scratches 抓痕391)imprint 压印392)dents 凹痕393)undulation 波动394)folder 折叠395)warp 弯曲，弄弯396)telescope 叠缩，嵌入397)knock 敲击398)bur. 粘附物399)edge wire 边丝400)simulation 模拟401)deform resistance 变形阻力。

酸轧常用英语词汇(新)[1]

轧钢分册酸再生—工艺Aa density meter 密度仪a pneumatically operated valve 气动阀absorber 吸收塔agglomerate 聚结agitator 搅拌器air cylinder 气缸ammonia agitator 氨水搅拌器aqueous ammonia-solution 氨水溶液automatically 自动地，机械地Bbeam 横粱bolt 螺钉Ccake bin 滤饼槽coated steel 镀层钢collecting tank 收集罐combustion gases 燃气commissioning 调试、试车compensators 补偿器consumption 消费(量) contaminate 污染countercurrent 逆流CPVC 氯化聚氯乙烯Ddemineralised water 脱盐水dust separator 粉尘分离器Eelectromagnetic hoist 电磁吊· 2 ·evaporate 蒸发、脱水evaporated 蒸发的exhaust gas fan 废气风机Ffilter 过滤器filter press 压滤机Filter tissue 过滤网．filtrate 滤出液flange 法兰flocculant 絮凝剂FRP 玻璃钢funnel 漏斗HHDPE 高密度聚乙烯heat exchanger 热交换器hydraulic cylinder 液压缸hydrochloric acid 盐酸hydrogen chloride 氯化氢IImmersion tub 插入管impeller 叶轮insert 插入、嵌入Iron oxide 氧化铁leaching column 溶解槽liquid 液体lump breaker 块状破碎机Mmanhole cover人孔盖metering pump 计量泵Nniobium 铌nitrogen 氮气nozzle plate 喷板· 4 ·oxidation 氧化oxide bin 氧化物料仓oxygen 氧气PPE 聚乙烯pH-value pH值pickle line 酸洗线piston 活塞plug 塞子PP 聚丙烯PPH 均聚聚丙烯precipitate 沉淀(物) preconcentrator 预浓缩塔process bin 工艺槽protection tube 保护管PTFE 聚四氟乙烯· 5 ·purification 纯化PVC 聚氯乙烯PVDF 聚偏二氟乙烯Rrefractory brick 耐火砖regenerated acid 再生酸regeneration 再生residue 残渣、滤渣retention bin 存料仓roaster 焙烧炉rotary valve 旋转阀Sscrap iron 铁屑screw conveyer 螺旋输送机scrubber 洗涤塔sedimentation bin 沉淀槽sedimentation bin 沉淀槽· 6 ·shell 外壳silica Removal Plant 脱硅线slight negative pressure 微负压slurry 泥浆solid particle 固体颗粒spray boom 喷射梁spray boom tube 喷粱管spray system 喷淋系统squeegee roller 挤干辊stack 烟囱steel structure 钢结构storage tank 储酸罐support 支撑swivel 旋转Tthe absorption column 吸收塔the chloride-content 氯含量the filter cake 滤饼·7 ·the hot roasting gases 热焙烧气体the leaching column 溶解槽the preconcentrated acid 预浓缩过的酸the preconcentrator 预浓缩塔the recirculation pump 循环泵the rinse water 漂洗水the spray nozzle 喷嘴transfer pump 输送泵tray 盘、碟Uundissolved 未溶解的Wwaste acid 废酸watervapour 水蒸气·8 ·酸再生—焙烧炉Aambient temperature 环境温度Bbasicity 碱度blower 风机burner chamber 烧嘴燃烧室Ccalorific value 热值charging 装料chimney 烟囱COG gas 焦炉煤气coke oven gas 焦炉煤气·9 ·Ddew point 露点discharging 卸料dust 灰份Eemergency water 事故水exhaust 排气Fflame detector 火焰监测器fuel gas 燃气furnace 炉子GGas-fired 燃气式·10 ·Hhose 软管humidity 湿度Iinsulation material 绝热材料Mmain burner 主烧嘴naphthalene 萘net calorific value 净热值Oorganic sulphur 有机硫pilot burner 点火烧嘴11pressure 压力purge 吹扫purity纯度Rrefractory brick lining 耐火砖衬roasting reactor 焙烧炉Ssolid particle 固体颗粒sparking electrode 点火电极stack 堆垛suspended solid 固体悬浮物Ttar 焦油thermocouple 热电偶·12 ·酸轧机组—工艺Aacceleration 加速度accessories 附件accuracy 精度acid 酸adjust 调整alarm 警报amount 数量automatically 自动地auxiliary 辅助的Bband 带bander 打捆机barrel 桶bay 跨；间·13 ·beam 梁because 因为bed 底座bender 弯曲装置，弯管机bevel 斜面bridle 辊式张紧装置bucket 桶burr 焊疤carrousel 卡罗塞尔卷取机casing 罩center 中心coefficient [数]系数coil 钢卷compensation 补偿console 操作台constant 常数controller 控制器·14 ·conveyor 输送机coolant 冷却液cooler 冷却器correspond 协调counter 计数器cover 盖cradle 鞍座crane 起重机curve 曲线Ddeceleration 减速deflector 偏转板detector 探头device 装置diagram 图表diameter 直径dust 灰尘·15 ·Eemergency 紧急情况emulsion 乳化液energy 能量entry 入口equipment 设备external 外部的Fforce 力frame 框架fume 烟function 功能Ggap 缝隙；辊缝gauge 量规；厚度grip 把手Hhard 硬harmonic 调和的heater 加热器Iindicator 指示器inhibitor 缓蚀剂interrupt 中断intersection 交点Interstand 中间机座lamp 灯length 长度leveler 水平仪levelling 矫直机line 线load 负荷looper 活套Mmarks 标记masher 磨碎机flow 秒流量measuring 测量meter 米；仪表mill 轧机Nnotch 缺口Oopener 直头机Ppanel 盘pickling 酸洗pinion 齿轮轴，小齿轮piping 管路pit 槽，坑plate 盘子plating 电镀pocket 袋、槽point 点pole 极position 位置pressure 压力prevent 预防processor 信息处理机pulse 脉冲pump 泵quality 质量Rratio 比率reducer 减速器reel 卷轴rinse 漂洗ripple 脉动roll 轧辊rolling 轧制rolling schedule轧制图表Ssaddle 鞍座safety 安全sampling 取样scale 氧化铁皮schedule 进度表scope 范围scrap 废料section 部分；截面sensor 传感器shaft 轴shear 剪切shop 车间shutter 关闭skid 制动器subber 缓冲器source 信号源spare 备件spindle 传动轴spot 斑点；污点spray 喷雾；喷嘴stand 机架standard 标准steel 钢storage 存储；库supply 供应support 支座switch 开关Ttail 尾部tank 槽；罐temperature 温度tension 张力thickness 厚度thread 线torque 扭矩tracking 跟踪transfer 移动；传输type 类型Vvalue 价值valve 阀Wwarning 警告wave 波width 宽度weigh 重量welder 焊机laser welder 激光焊机width 宽度winch 绞盘wire 金属丝；电线wrapping 包装23酸轧机组—生产管理Aaverage 平均值average pickling speesd 平均酸洗速度average TCM speed 平均轧制速度Bbar code information 条形码信息Ccoil No．钢卷号compressed air 压缩空气concentration 浓度control thickness 轧机控制厚度crown 凸度cut mode 切割方式·24 ·Ddata classification(TC) 数据分类(冗)defect class 缺陷等级defect type 缺陷类型discharging temp(slab) 出炉温度(板坯) dismount upper roll No 撤销上轧辊号dR．chock No．传动侧轴承座号dR．Exit coil thickness 出口卷传动侧厚度Eedge state 边部状态elapsed time 休止时间end time 生产结束时间error type 故障类型Fflatness 平直度frequency of sample 取样频率25Hheat no 熔炼号S1 stand elongation S1机架延伸率S1 stand front tension S1机架前张力S1~32 stand tension S1-S2机架间张力Ilower Roll crown 下轧辊凸度Mmaterial tension grade 材料强度等级max．pickling speed 最大酸洗速度Nnode ID 节点号·26 ·Op.chock No，操作侧轴承座号Op．Exit coil thickness 出口卷操作侧厚度original hot coil No 母卷号(最初热卷号) overall judgement result 综合判定结果Ppickling data 酸洗数据pL Derail defect data PL缺陷数据position of sample 取样位置preceding process code 前道工序号process code 机组号Rreserve 预留roll roughness 轧辊粗糙度roll shape code 轧辊外形代码roll type 轧辊类型·27 ·Ssample mark 取样标志sample code 试样号sorting grade 分选度spec．change 规格变换spool code 套筒代码stand No．机架号starting position 开始位置steel grade 钢种stoppage data 停机数据Ttaper 锥度temperature of pickling bath酸洗槽温度tension leveler code 拉矫代码tension leveler elongation 拉矫延伸率test No．测试号the number of coils 钢卷数·28 ·the number of division 分卷数量the number of entry 人口卷数目the number of weld points 焊接点数tons rolled 轧辊轧制吨数transmission date 传送日期trimming width 切边宽度type 类型Uused material weight 使用原料重量user ID (withholder) 封闭责任者代码Wweighting measure 重量测量weld position 焊缝位置weld type 焊缝类型withholding reason 封闭原因work order No．生产合同号Sol-A1 酸熔铝·29 ·酸轧机组—机械Aacc stand 蓄能器站agitator 搅拌器air blast 空气喷吹装置air breather 空气滤清器air clutch 气动离合器air Cyl 气缸air filter 空气过滤器air ventilation system 通风系统air Wipers 空气吹扫装置apron 护板auto flex coupling 自动柔性、联轴器auxiliary Equipment 辅助设备Bback-up roll changing rails 支撑辊换辊轨道·30 ·bag Filter 布袋过滤器ball bearing 滚珠轴承ball Screw Jack 滚珠丝杆千斤顶ball valve 球阀barrel pump 桶式泵base 底座bearing 轴承belt wrapper 皮带助卷器bevel gear 锥齿轮bevel gear box 伞齿轮箱breaker roll 抗折弯辊brick Lining 砖衬bridle roll 张紧辊子BUR 支撑辊burr masher 去毛刺机butterfly valve 蝶阀Ccam 凸轮·31cam follower 随动轴承carrousel type Tension Reel Carrousel式张力卷取机carryover Table 辊道运输台板centering Device 对中装置centrifugal fan 离心式风机contrifugal separator 离心式分离器chain and sproket 链条与链轮chain coupling 链条联轴器check valve 单向阀chock 轴承座clutch 离合器cobble guard 防缠导板coil band cutter 打捆带剪coil opener 开卷器coil transfer car 钢卷运输车combination tool 组合工具commercial parts 通用件controller 控制器coolant oil supplying system 乳化液供液系统·32 ·coupling 联轴器cover lifter 盖提升机cover ,retainer,thrust ring 端盖、挡环、止推环cradle roll 鞍座辊cubicle 控制柜Ddam roll 坝辊damper 挡板deck 盖板delivery coil car 卸卷小车delivery section equipment 出口区设备detector 检测器differencial pressure switch 压差开关differential Gear 差动齿轮disk spring 碟形弹簧distributor 分配器dividing shear 切分剪double cut shear，双切剪·33 ·drum 卷筒dryer 干燥机DS mill housing 操作侧牌坊dust seal 挡尘圈Eearth clamp 接地夹子eccentric wheel 偏心轮eck radial bearings 径向轴承electrical heater 电加热器eliminator 分离器entry coil car 人口钢卷小车eye bolt 调环螺拴Ffan 风机fire damper 防火挡板fitting bolts 紧固螺栓fixed Beam 固定梁·34 ·flange 法兰flash suction duct 闪光吸入管flash Welding Machine 闪光焊机flexible joint 柔性接头flow meter 流量计flow sight 流量显示器foot chain 脚链foundation bolt & Nuts 地脚螺栓&螺母frame 框架flanges 法兰fume exhaust 烟雾抽排fume exhaust system 废气排放系统Cgauge valve 仪表阀gear 齿轮gear coupling 齿轮联轴器globe valve、Gate valve 截止阀、闸阀gratings 隔栏·35 ·grease gun 润滑脂枪grease nipple 干油嘴guide 导板．guide rod 导向杆guide Roll 导向辊子Hhand pump 手动泵heat exchanger 热交换器hold Down Roll 压下辊hook 钩housing机架housing lifting beam 牌坊吊梁hyd．Cyl．液压缸hyd．Motor 液压马达hyd．Cyl．for swing 摆动液压缸hyd．Cyl．forpinch 夹紧液压缸hyd cylinder for IMR keeper plate 中间辊保持板锁紧缸hyd．cylinder for IMR shift 中间辊窜动缸·36 ·hydraulic Valve Stands 液压阀台Iinspection Mirror 检查镜intermediate roll 中间辊Jjig 夹具Kkeeper plate for IMR 中间辊锁紧板knives 剪刃Lleveller Driving System 破鳞机驱动系统levelling Mill 破鳞机levelling Roll 矫直辊lever 杠杆·37 ·lift Cyl，Bracket 提升缸支架load cells 测压头looper Car 活套小车Mmagnetic separator 磁性分离器mandrel 心轴mandrel neck 轴颈manual Hoist beam 手拉葫芦梁measuring valve ．测量阀middle roll 中间辊mill entry and Exit Guides 轧机入口和出口导板mill Exit Protection Cage 轧机出口防护罩mill Hood 轧机护罩mill Stands 轧机机架mill Wash Down Unit 轧机清洗装置mixing tank 混合槽motor base 马达底座motor cylinder for side shift 侧移马达缸·38 ·Nneck thrust bearings 推力轴承needle valve 针阀notcher 月牙剪oil cooler 油冷却器oil plug 油塞oiless bush 含油轴承ON-OFF air valve 气动开关阀Ppay-off reel 开卷机pillow Block 轴承座Pin 销子pinch Roll Chock 夹紧辊轴承座pinion 小齿轮piping on the machine 机上配管·39·polyurethane Lining 聚胺脂衬potable pump 饮用水泵presure gauge 压力表presure reducing valve 减压阀processor 直头机projet block 弯辊块Protector 保护器pulley 滑轮pump 泵puncher 冲孔机push pull car 推拉车Qquick joint 快速接头Rmill & base 轨道与底座ram 推杆ratchet wheel 棘轮·40·reducing valve 减压阀regulator 调节器relief valve 安全阀retaining ring 定位环rinse tank 漂洗槽rocker 摇杆rod 杆roll Bending 弯辊rotary cylinder 旋转缸rotary joint 旋转接头rubber coupling 弹性接手Ssaddle 鞍座scrap chopper 碎边剪scrap chute 废料溜槽screw jack 螺旋千斤顶screw Shaft 丝杆轴scrubber 洗涤塔·41 ·shaft 轴shift block 窜动块shutter 卷帘门skid 滑动座sleeve 钢套sleeve feeder 装套器sleeve ramp 套筒滑道slide liner 滑动衬板slip ring 集电环snubber Roll 缓冲辊socket bolts 内六角螺拴speed meter mountings 测速仪支架spherical bush 球面套spindle 轴splash Cover 飞溅罩spray Header 喷射集管spray header for delivery strip cooling 出口钢带冷却喷射集管spray Nozzle 喷嘴spray Valve 喷射阀·42·steam heater 蒸汽加热器steering Roll 纠偏辊子stop valve 停止阀strainer 过滤器strtching Gear Reducer 拉伸齿轮减速机strip Clamp Car 带钢夹持车strip Lifter 带钢提升机suction strainer 吸人过滤网swing Roll 摆动辊子switch 开关TTension meter roll 张力计辊子timing belt 同步带top BUR balance cylinder 上支撑辊平衡缸torque limitter 扭矩限制器traverse Cyl Bracket 横移缸支架trimmer 切边剪twin basket type filter 双筒式过滤器·43 ·tyre coupling 轮胎联轴器Uuncoiler 开卷机universal Joint 万向联轴器Vventilator 通风机volume damper 流量挡板o—ring O型圈Wwalking beam 步进粱washer 垫圈wearing plates for project block windows 平衡块耐磨衬板wedge Roll 楔辊wedged plates 斜楔板weigher 称重机welder 焊机·44·wheel 轮子worm jack 蜗杆winger roll 挤干辊磨辊间—工艺accuracy 精度axis 轴back up roll 支撑辊bearing 轴承chock 轴承座compensation 补偿coolant 冷却液crack 裂纹crown 凸度Ddetection 探测dinameter 直径dielectric oil 绝缘油Eeddy current tester 涡流探测器edt(electrical dischange texturing) 电火花打毛electrode 电极empirical-shaped 经验辊型Ffaceplate 花盘Cgenerator 发生器grind 磨削47grinding machine 磨床grinding wheel 砂轮Hhardness 硬度headstock 床头箱hydrodynamic 动压hydrostatic 静压Iintermediate roll 中间辊Llurfication 润滑Jjib crane 旋臂吊·48 ·Umeasurement 测量Nneck 辊颈Ppad 垫、瓦profile 轮廓、外形Qquill 套筒Rrecording station 检查台rms 轧辊间管理系统roll 轧辊·49·roll shop 轧辊间roughness 粗糙度roundness 圆度Ssemi-gantry roll loader 半臂龙门吊spindle 轴steady rest 托架stock removal 磨削量storage pad 搁架surface 表面Ttailstock 尾架taper 锥度texture 打毛transfer car 运输小车·50 ·Uultrasonic 超声波Vv-belt v型皮带workpiece 工件work roll 工作辊磨辊间—机械Aanchor parts 固定件automatic drying wiper 自动干燥棉拭器Bbarrel chamfer grinding 圆柱状斜面磨削bedway covers 滑板盖Ccaliper 卡规cambering mechanism 向上弯曲机构carriage bed 床身chocks 轴承座concave 凹面control cabinet 控制柜convex 凸面·52·cover plates 盖板crack and bruise detecting device 裂缝和划伤检测装置crane 行车、起重机crossways 横仪轨道cylindrical 圆柱的Ddiamond 金刚石driving dogs 驱动爪Eeccentric grinding spindle 偏心轴Eeddy current testing 涡流探伤·53 ·Fflat shape grinding 平形磨削Cgear wheel pump 齿轮泵grinder 磨床grinding coolant system 磨削液系统grinding wheel 砂轮Hheadstock 床头箱heavy duty type 重载类型Iinfinitely variable 无级变速loader 装货机·54 ·Mmagnetic filter 磁性过滤器mirror corwn grinding 对称冠性磨削multi-machine operation 多机床操作multi-shift operation 轮班操作Ppaper filter 纸过滤器positioning accuracy 定位精度probes 探针profile 剖面Rribbed cast iron 带肋铸铁件roll shop 磨辊间roll transfer car 辊子运输小车ruler 标尺·55·Ssinusoidal barrel 正弦辊形special measuring tools 专用测量工具steady rest left 左侧固定架storage pads 储存架storage racks 储存架suction pump 抽水机swarf boxes 铁屑箱Ttailstock 机床尾架telescopic way covers 伸缩轨道盖teleservice 电信服务travelling carriage 移动车架twisted pair 双绞线Uu-axis U轴·56 ·universal roll griding machine 万能轧辊磨床Wworkpiece bed 车架Xx-axis x轴电气AA/D 模拟／数字acceleration 加速度accident 事故accumulator 蓄电池accuracy 精确性actuator 执行器address 地址adjustment 调节器alarm 警报ammeter 电流表amperage 安培数amplifier 放大器amplitude 幅值analysis 分析annunciator 信号器·58 ·appendix 附录arithmetic 算法armature 电枢arrester 制动器attachment 附加装置automatic 自动机械Bbar code 条形码battery 电池baud 波特率bin 箱柜binary 二进位bit [二进制]位blower 送风机、吹风机breaker 断路器buffer 缓冲器button 按钮buzzer 蜂鸣器·59byte 字节Ccabinet 柜cable 电缆cancel 取消capacitor 电容器capacity 容量cell 电池center 中央chamber 室channel 通道character 特征charge 负荷chopper 断路器circuit 电路class 等级client 客户机code 代码·60 ·command 命令comment 注释communication 通讯condenser 电容器connect 连接constant 常数contactor 接触器control 控制converter 整流器current 电流cycle 循环DD／A 数字／模拟data 数据database 数据库defect 过失deflector 变流装置delivery 出口·61 ·description 描述desktop [计]桌面detector 检电器device 装置diagnostic 诊断的diagram 图表dial 刻度盘digital 数字的diode 二极管direction 方向display 显示distance 距离drive 传动Eelectric 电的、电气electricity 电流、电、电学electrode 电极emergency 紧急情况·62 ·encoder 编码器entry 入口equipment 设备error 错误Ethernet 以太网exhaust 排放Ffacility 设备fan 风机fault 故障feedback 反馈field 域、地区figure 数字filter 过滤器flux 磁通frequency 频率function 功能fuse 熔断器·63 ·Ggauge 测量gear 传动柜generator 发生器grounding v．[电]接地Hhardware 硬件heater 加热器horn 喇叭hydraulic 液压的Iimpedance 阻抗indicator 指示器induction 感应input 输人insulation 绝缘·64 ·interface 接口interrupt 中断inverter 逆变器Kkeyboard [计]键盘Llamp 灯LAN 局域网layout 布局图LED 发光二极管light 灯list 列表Mmagnet 磁铁manual 手册master ，主机·65 ·maximum 最大measure 测量memory 存储器menu 菜单minimum 最小modem 调制解调器module 模式monitor 监视器motor 电动机NNetwork 网络operator 操作员option 选项·66 ·Ppanel 面板parameter 参数phase 相位plug 插头polarity 极性power 功率pressure 压力printer 打印机procedure 程序process 过程protocol 协议pulse 脉冲pushbutton 按钮Rrated 额定receptacle 插座·67 ·recuperator 换热器regulator 调整器relay 继电器remote 远程的resistor 电阻器Ssafety 保险selector 选择器semiconductor 半导体sensor 传感器sequence 顺序Server 服务器signal 信号snubber 缓冲器socket 插座software 软件solenoid 电磁阀starter 启动器·68 ·station 站supervision 监视switch 电闸switchboard 配电盘switchgear 开关设备system 系统Ttechnical 技术的temperature 温度tension 张力Terminal 终端thermocouple 热电偶thermometer 温度计thermostat 自动调温器timer 定时器transmitter 变送器·69 ·Uunit (计量)单位Vvalve 阀variable 变量vector 矢量velocity 速度via 经voltage 电压voltmeter 伏特计Wwinding 绕组wire 电线·70 ·缩写A1S-2P single solenoid and two position1S-2P单电磁线圈两位(阀)2S-2P double solenoid and two position 2S-2P 双电磁线圈两位(阀)2S-3P double solenoid and three position2S-3P 双电磁线圈三位(阀)ABS absocorder(absolute—encoder)(绝对值编码器)和SYN不一样ACC acceleration加速器、加速度ACM ac motor交流电动机ACR automatic current regulator自动电流调节器ACRR automatic current rate regulator自动电(气)流强度调节器，·71 ·ADJ adjust调整、调节AEC automatic elongation control自动延伸率控制AGC automatic gauge control自动厚度控制AGM aC gear motor交流齿轮电机AHY auxilliary hydraulic system for tcm & pl delivery TCM和PL传输辅助液压系统AI analog input模拟量输入·AIC analog input controller模拟量输入控制器AISD automatic intermediate slow down自动降速AMP amp．cub比例阀放大板柜·72 ·ANN annunciator信号器、报警器AO analog output模拟量输出APC automatic position control自动位置控制ARP acid regeneration plant酸再生AS ac current select电流选择ASD automatic slow down自动慢车ASR automatic speed regulator自动速度调节器ATL automatic tension limit自动张力限制控制ATR automatic tension regulator 自动张力调节器，·73 ·AUX auxiliary辅助的、附属的A VR automatic voltage regulator 电压自动调节器、自动稳压器BB buy买方B／W belt wrapper皮带助卷机BAF bell annealler facility罩式炉BCR back uproll conveyor car支撑辊换辊小车BEL bell钟、圆锥状物、电铃、铃(声)、响铃Bend bender弯管机·74 ·BI built-in type magnet brake内置型电磁抱闸BOT bottom底部、下部BR bridle roll张紧辊BR br．cub．电磁抱闸柜HRG bearing轴承BT battery & distribution电池和配电BUR back up roll支撑辊BWD backward向后的、向后BZ buzzer蜂鸣器·75 ·CC／C Trax coil car transfer运卷小车CAN control area network控制区域网络(CAN总线又称DeviceNet总线) CGL continuous hot dip galvanizing line连续热镀锌线CHG changing替换、变换、变化CL(GLS) cam limit switch/geard limit switch 凸轮限位开关Gear(齿轮)CLF current limiting fuse限流熔丝CNT counter计数器、计算器CO CO--manufacturing联合制造·76 ·Compen compensat补偿、校正、均衡、偿还、付报酬CONDUCT conductivity传导率、传导性、电导率、电导性Const constant常数、恒定值、恒量CONV converter整流器COS change Over switch改变结束开关CPC center positioning cortrol带钢对中CPL continuous pickling line连续酸洗线CPR恒定压力调节器CPU central processing unit中央处理单元·77 ·CRT显示器CS control switch控制开关．CSR change spring reverse switch弹簧转换倒顺开关CT current transformer变流器、电流互感器CTR carrousel type tension rell卡鲁塞尔卷取机CTT contactor电流接触器CUB cubicle柜CV control valve servo valve控制阀、伺服阀、从动阀CVF cellar vent．fan地下室通风风机·78 ·CWT coil weighing scale钢卷重量测量DD delivery运送、输送、输出D／L drive linkage驱动连接、链系DBR dynamic brake电动制动器DCM direct current motor直流电动机data equalizing bus that transfers DCM bus common control data from the mastercpu(hpu) to the standby cpu(hpu) DCM bus 数据平衡总线是从主CPU（HPU）备用CPU（HPU）的普通传输控制数据DEC decelerate(使)减速·79 ·DEF．deflector转向辊、偏转DGS digital switch数字开关DI digital input数字量输入DLA diameter直径DIF direct pi／o interface直接过程输入输出接口DL drive linkage驱动连接、链系DO digital output module数字输出模板DP differential pressure switch压差开关DPM dual port memory双端口记忆·80 ·UPR delivery pinch roll出口夹紧辊DS double solenoid valve双线圈阀DSA pneumatic double solenoid气动双线圈阀DSH hydraulic double solenoid液压双线圈阀EE entry登录、条目、进入、人口E．END emergency end紧急状况(事故)结束E．S emergency stop紧急停车E／R electric room电气室·81 ·ECC查错和纠错EE electronic equipment电子设备EH electronic heater电加热器EIC electrical instrumentation and computer 电气的仪器、仪表和计算机Elet electrical电的、电气的、与电有关的EMF electrical motive force电气的原动力、推动力ENT entry进口、人口ES(E．S) emergency stop pbs紧急停车EWS engineering work station工程工作站·82 ·FFB feed back反馈FC function code功能[操作]码FFB fuse free breaker无熔丝断路器FG frame graound termial框架接地端FGC flying gauge changing自动换规格FI flow transduser流量传感器FL finish line精整线FS flow switch流量开关、气流换向器·83 ·GCB gas circuit breaker气体断路开关GND地线GP means control parel with grahic panel display 表明带图形显示的控制盘HHC hard copy硬拷贝机HCD HCDHITACHI的保存装置(当为了故障诊断执行测试和维护程序时连接这个HCD)HI hardwire input硬连线输入HKP hardware kemal program硬件核心程序84HM mill stands轧机机架HMD(HD) hot metal detector热金属检测器HMI hmi desk操作站、人机界面HO hardwire output硬连线输出HPU handling control cpu用于处理控制的CPU.功能和速度比CPU小HPU high speed electical control processor unit 高速电气控制处理单元HSCB high speed circuit breaker高速自动断路器HYD hydraulic液压的、水压的·85 ·II/D inner dia．内径I/F(IF) interface接口ID intelligent director智能的控制仪表IGBT insulated gate bipolar transistor绝缘栅双极晶体管IM induction motor感应电动机IMR intermediate roll中间轧辊INC increase加、增加、加速INR inching reversible微动、微调可逆的·86 ·Inspec inspection检查、验收、探伤Inst instrument仪器、仪表、仪器、工具INV(INV) inverter逆变器IPO inspection reel检查滚筒ITV industry tv工业电视JJIS 日本工业标准KK 轧机系数·87 ·LLAN local area network局域网LANCP lan pc局域网网卡LANCP lan control processor局域网控制处理器LC load center负荷中心LC low-pressure cupboard低压配电柜LC load cell测压元件LCB local control box switch(pendant box)本地控制箱开关(悬吊箱)LED light emitting diode发光二极管·88 ·LEH post type pulse generator柱(杆)式的脉冲发生器LEN length长度、时间的长短LG．line filter groud termianal．线性滤波器接地端子LI liquid level transducer液位传感器’LP loop sensor环形传感器LS post type mangnetic brake柱(杆)式的电磁抱闸LSH level type limit switch水平(位)式行程开关LST fork type limit switch叉式行程开关LSV sleeve loading system钢卷加套筒系统·89 ·LT float switch浮动开关LUB lubrication润滑油LV level converter液位／电子变换器Mmeans control panel with graphic panel display heavy 重的、繁重的、巨大的、沉重的，MAC medium access cortrol介质通路控制MB magnetic brake磁制动器MC magnetic clutch电磁离合器MCB main circuit breaker主断路器·90 ·MCC motor control center电机控制中心MCCB mccb panel塑壳空气断路器电路盘MCS metal clad switchgear铁壳开关装置MDV mill drive gear boxes轧机传动齿轮箱MEAS measuring测量MICA modular intergrated concept architecture 模块集成概念结构(指日立的PLC编程软件) MINS module／network status模块／网络状态MRH master rheostat主变阻器MS magne scale磁尺·91 ·MV magnet valve电磁阀、磁力阀MV／CUB magnet value cubicle电磁阀柜NCP nσnetwork cp NCPu∑Network 网卡NNL near limit switch接进行程开关O／D outer dia外径OS operation system操作系统·92 ·PPBL pbs with lampPBS push button switch按钮开关PC pressure cell测压头、测压发送器、压敏元件PC NO plc no．PLC号PDB plant database subsystem工厂数据库子系统PDI pri mary data input生产指令数据的基本数据信息、初始的数据输入PF power factor功率因数PG piolt generator辅助发电机、测速发电机·93 ·PC(PLG,PL) pulse generator(600 pulse/turn)脉冲发生器(600个脉冲／每圈)PH photo cell／photo switchPH光电发射管、光电开关PI pressure transducer压力传感器PI／O process input／output过程输入输出PIF plant interface & console设备接口和控制台(用于PLC和HSC6800控制面板连接的模扳PIFA pif adaptorPIF模扳的接头PL pulse generator for asr(1200 or 2400 pulse/turn) 用于速度调节器的脉冲发生器(1200或2400个脉冲／每圈)PL plg for asr with motor shaft电机轴上的脉冲发生器用于自动速度调节器·94 ·PLC programmable logic controller可编程控制器PLS PLS速度传感器PL-TCM pickling line tandem cold mill酸洗连轧线PM potensio(potential) meter电位计POLPOR pay-off reel开卷机POS position位置PR printer打印机PRESS pressure压力·95 ·PROC(Ptoce) processor处理机PS pressure switch压力开关PS power source module电源模板PS(P．S) power stop pbs电源停止PSE programming support equipment程序设计配套设备PSI position and speed detection interface 位置和速度检测接口PSW position switch接近开关PT position transmitter位置变送器PTI．pulse train input脉冲序列输入·96 ·PV proportional valve比例阀PWM pulse width modulate脉冲调制、脉宽调制PX．S proximity switch近程开关QQ．S quick stop快速停车·RRB rheostat braking制动电阻’RCG roll change换辊REC roil eccentric control轧辊偏心控制·97 ·REF reference参照、参考RG ramp generator斜坡发生器·RI remote input远程输入RIO(RI/O/O remote i／O远程RIW remote input word远程输入(字)RO remote output远程输出RPC roll load systam(hyrop—f systan)轧辊加载系统(压上系统)RS rotary type cam limit switch凸轮式限位开关RW ref．work中间存储器(参考工作)·98 ·RY relay继电器SS／C scrap chopper碎边剪S／D synchro to digital给数字信号同步S／E线性编码器S／E sine encoder正弦编码器S／R snubber roll缓冲辊S／T side trimmer切边剪SA surge absorber[过压、电涌]吸收器、避雷器‘99 ·SB光电转换器SD speed detector转速检测装置SE sine encorder for asr (16000 pulse/turn maindrive)自动速度调节器的正弦编码器(16000个脉冲／每圈用于主传动) ·SH space heater空间加热器(用于6台主电机)SHD shield屏蔽线SHT mill shutter轧机活门(卷帘门)SL signal lamp信号灯SNSW snap switch速动开关·100·SOL solenoid电磁铁(solenoid valve电磁阀)SP speed速度SPM shape meter roll板型仪SR(RF) silicon rectiffer(selenium rectifier)硅整流(整流器)SS speed sensor速度传感器SS single solenoid valve单线圈阀SSA pneumatic single solenoid气动单线圈阀SSH hydraulic single solenoid液压单线圈阀SSR slid-state relay滑移、滑座、滑动状态继电器101·ST synchro transmitter同步发送机ST station module站模板STD stand机架、轧机SRR steering roll纠偏辊STU serial signal transmitting unit串行信号发送单元SV solenoid valve。

轧钢专业英语必备词汇

轧钢专业英语必备词汇(5)轧钢Rolling八辊轧机MKW mill板坯slab半连续热带轧机semi-continuous hot-strip mill 薄板sheet 薄板轧机sheet mill保温炉heat holding furnace扁锭slab ingot, slab扁钢flat bar不可逆轧机non-reversing mill步进梁式加热炉walking beam type furnace 槽钢channel 车底式加热炉car bottom furnace车轮轧机railway-wheel mill车丝机threading machine成卷coiling成品包装跨packing bay初轧机blooming mill初轧坯翻转装置bloom turnover device出料拉杆kick-out arm穿孔机piercing mill粗轧机rough mill淬火炉hardening furnace搭接炉焊管机lap-welded pipe mill打包用带钢轧机package mill打捆机bundle machine打捆机bundler打印台stamping station大型型钢轧机heavy section mill导辊装置roller guide地上卷取机up coiler地下卷取机down coiler地下卷取机down coiler地下油库oil cellar地下运输机tunnel conveyer叠板轧机pack mill定径机sizing mill定心机centering machine镀槽coating bath镀锡板tinning sheet镀锡槽tinning bath镀锡线tinning line镀锌板galvanized sheet镀锌槽galvanizing bath镀锌线galvanizing line堆储跨storage bay堆垛机piler钝化处理passivation多辊矫直机multi-roll straightening machine 方钢square bar 方坯bloom非连续性轧机non-continuous rolling mill飞锯flying saw干燥台drying station钢坯, 小方坯billet钢坯库billet store钢坯修磨conditioning高速线材轧机high speed wire rod mill高压水除鳞hydraulic jet descaler工字钢I-bar工字钢轧机I-beam mill工作辊换辊装置work roll changer工作辊支撑装置work roller supporting apparatus 钩式运输机hook transfer光亮退火炉bright annealing furnace轨梁轧机rail-beam section mill滚筒剪drum type shear横切机transversal shear厚板heavy plate厚板轧机heavy plate mill环形加热炉rotary hearth furnace换辊小车roll change carriage荒管, 毛管, 空心坯pierced billet, hollow billet回火炉tempering furnace回转剪rotary cropping shear活套loop活套张紧辊bridle roll机后输出辊道mill run-out table机架, 牌坊stand, housing机架辊breast roll机前输入辊道mill run-in table挤压机extruder夹送辊deflector pinch roll加热炉heating furnace碱槽alkaline bath剪切跨shear bay减径机reducing mill矫直机straightening machine, straightening mill角钢angle steel揭盖机cover carriage紧卷tight coil进料拉杆kick-in arm浸镀immersion coating井式炉pit batch type furnace精轧机finish mill精整加工线finishing machine精整跨finishing bay卷材, 线卷coil均热炉pit furnace均热炉跨soaking pit bay均整机,整径机(管) reeling machine开卷机, 拆卷机decoiler开坯机cogging mill可逆辊道reversing table空心坯减径机shell-reducing mill拉丝机wire-drawing machine扩径机(管) repiercing machine冷床cold bed冷锯cold saw冷轧板带钢cold rolled strip立辊vertical roll连续式加热炉continuous type furnace 连续酸洗continuous acid-washing链式运输机chain transfer磷化处理phosphate treatment磷酸phosphoric acid硫酸sulfurous acid炉卷机steckel mill炉用卷取机furnace coiler轮箍轧机tyre mill内表修磨inside grinding拧接头机coupling applicator盘条rod coil平立(万能)轧机horizontal-vertical (HV) mill 平整机temper machine破鳞辊descaling roll破鳞机scale breaker, descaler切边side crops切边剪end trimming shear切头top crops切头剪end shear切尾end crops去刺机deburring machine热处理heat treatment热带轧机hot-strip mill热镀hot-dip coating热锯hot saw热轧板带钢hot rolled strip乳化液emulsion森吉米尔轧机Sendzimir mill上料台架ingoing skid深冲薄钢板deep drawing sheet石油管套管pipe case收集台collecting table受料辊道receiving table输出辊道run-out table输入辊道run-in table水力除鳞hydraulic descaler水压试验机hydraulic pressure tester酸槽acid bath酸洗槽pickling bath酸洗工段pickling department酸洗机pickling machine酸洗线pickling line酸洗用酸acid for pickling甩尾back-end whip丝扣保护套thread protector四机架连续式带钢冷轧机four-stand tendem cold strip mill 松卷loose coil碎断剪chopping shear塔式酸洗机tower pickler套管接头pipe coupling铁皮坑scale pit通径机drifter筒式卷取机drum type coiler涂漆装置painting unit吐丝机laying head推钢机, 推杆pusher拖运机,移送机dragging device脱脂槽degreasing bath外表修磨outside grinding弯辊装置bending-up roll device万向连轴节universal spindle coupling无扭轧机non-twist mill无损探伤non destoryed test铣头机chamfering machine限动芯棒轧管机retained mandrel pipe mill硝酸nitric acid小型型钢轧机light section mill, merchant bar mill 芯棒式轧管机mandrel mill型钢, 条钢bar行星轧机planetary rolling mill修磨机grinder压下螺丝screw down压下装置, 压下机构screwdown延伸机elongator硬度试验机hardness tester油膜轴承oil film lubrication bearing预精轧机pre-finishing mill预热炉preheating furnace圆锭round ingot, round billet圆钢round bar圆盘锯circular saw运锭车, 翻锭车ingot buggy运输辊道processing table再加热炉reheating furnace轧边机, 立辊轧机edger轧钢rolling轧钢车间rolling plant轧管机设备tube mill equipment轧辊及辊道roller and table轧辊压下装置roller press-down device轧辊轴承座roll bearing chock轧辊支架roll support轧机rolling mill轧机传动装置rolling mill drive device轧机跨mill bay, mill aisle轧机输出辊道mill delivery table轧机输入辊道mill approach table窄带strip张力减径机(管) tension-reducing machine 张力控制tensioncontrol罩式炉bell type furnace支撑辊back-up roll中板轧机medium plate mill中厚板medium plate中间辊道intermediate table中型宽带轧机medium wide-strip mill中型型钢轧机medium section mill中轧机intermediate mill周期式轧管机pilger mill转盘turntable自动轧管机plug mill纵切机longitudinal shear, slitting shear。

1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。