钢结构专业术语英文简称与中文对照
建筑结构丨钢结构术语中英文对照，按字母分类，收藏留用吧！
建筑结构丨钢结构术语中英文对照，按字母分类，收藏留用吧！强度strength承载能力load-carrying capacity脆断brittle fracture强度标准值characteristic value of strength强度设计值design value of strength一阶弹性分析first order elastic analysis阶弹性分析second order elastic analysis屈曲buckling腹板屈曲后强度post-buckling strength of web plate通用高厚normalizde web slenderness整体稳定overall stability有效宽度。
effective width有效宽度系数effective width factor长细比 slenderness ratio换算长细比equivalent slenderness ratio支撑力 nodal bracing force无支撑纯框架unbraced frame强支撑框架frame braced with strong bracing system弱支撑框架frame braced with weak bracing system摇摆柱leaning column柱腹板节点域panel zone of column web球形钢支座spherical steel bearing橡胶支座couposite rubber and steel support主管chord member支管bracing member隙节点 gap joint搭接节点 overlap joint平面管节点 uniplanar joint空间管节点multiplanar joint组合构件built-up member钢与混凝土组合梁 composite steel and concrete beamAacceptable quality 合格质量acceptance lot 验收批量aciera 钢材against slip coefficient between frictionsurface of high-strength bolted connection高强度螺栓摩擦面抗滑移系数allowable ratio of height to sectionalthickness of masonry wall or column砌体墙、柱容许高厚比allowable slenderness ratio of steel member 钢构件容许长细比allowable slenderness ratio of timbercompression member 受压木构件容许长细比allowable stress range of fatigue 疲劳容许应力幅allowable ultimate tensile strain ofreinforcement 钢筋拉应变限值allowable value of crack width 裂缝宽度容许值allowable value of deflection of structuralmember 构件挠度容许值allowable value of deflection of timberbending member 受弯木构件挠度容许值allowable value of deformation of steelmember 钢构件变形容许值allowable value of deformation of structuralmember 构件变形容许值allowable value of drift angle of earthquakeresistant structure抗震结构层间位移角限值amplified coefficient of eccentricity 偏心距增大系数anchorage 锚具anchorage length of steel bar 钢筋锚固长度approval analysis during construction stage 施工阶段验算arch 拱arch with tie rod 拉捍拱arch-shaped roof truss 拱形屋架area of shear plane 剪面面积area of transformed section 换算截面面积aseismic design 建筑抗震设计assembled monolithic concrete structure 装配整体式混凝土结构automatic welding 自动焊接auxiliary steel bar 架立钢筋Bbackfilling plate 垫板balanced depth of compression zone 界限受压区高度balanced eccentricity 界限偏心距bar splice 钢筋接头bark pocket 夹皮batten plate 缀板beam 次梁bearing plate 支承板bearing stiffener 支承加劲肋bent-up steel bar 弯起钢筋board 板材bolt 螺栓bolted connection 钢结构螺栓连接bolted joint 木结构螺栓连接bolted steel structure 螺栓连接钢结构bonded prestressed concrete structure 有粘结预应力混凝土结构bow 顺弯breadth of wall between windows 窗间墙宽度building structural materials 建筑结构材料building structural unit 建筑结构单元building structure 建筑结构built-up steel column 格构式钢柱bundled tube structure 成束筒结构burn-through 烧穿butt connection 对接butt joint 对接butt weld 对接焊缝Ccalculating area of compression member 受压构件计算面积calculating overturning point 计算倾覆点calculation of load-carrying capacity ofmember 构件承载能力计算camber of structural member 结构构件起拱cantilever beam 挑梁cavitation 孔洞characteriseic value of live load on floor orroof 楼面、屋面活荷载标准值characteristi cvalue o fwindload 风荷载标准值characteristic value of concrete compressivestrength 混凝土轴心抗压强度标准值characteristic value of concrete tensilestrength 混凝土轴心抗拉标准值characteristic value of cubic concretecompressive strength 混凝土立方体抗压强度标准值characteristic value of earthquake action 地震作用标准值characteristic value of horizontal crane load吊车水平荷载标准值characteristic value of masonry strength 砌体强度标准值characteristic value of permanent action 永久作用标准值characteristic value of snowload 雪荷载标准值characteristic value of strength of steel 钢材强度标准值characteristic value of strength of steel bar钢筋强度标准值characteristic value of uniformly distributedlive load 均布活标载标准值characteristic value of variable action 可变作用标准值characteristic value of vertical crane load 吊车竖向荷载标准值charaeteristic value of material strength 材料强度标准值chimney 烟囱circular double-layer suspended cable 圆形双层悬索circular single-layer suspended cable 圆形单层悬索circumferential weld 环形焊缝clear height 净高cold bend inspection of steelbar 冷弯试验cold drawn bar 冷拉钢筋cold drawn wire 冷拉钢丝cold-formed thin-walled sectionsteel 冷弯薄壁型钢cold-formed thin-walled steel structure 冷弯薄壁型钢结构cold-rolled deformed bar 冷轧带肋钢筋column bracing 柱间支撑combination value of live load on floor orroof 楼面、屋面活荷载组合值compaction 密实度compliance control 合格控制composite floor system 组合楼盖composite floor with profiled steel sheet 压型钢板楼板composite roof truss 组合屋架compostle member 组合构件compound stirrup 复合箍筋compression member with large eccentricity 大偏心受压构件compression member with small eccentricity 小偏心受压构件compressive strength at an angle with slopeof grain 斜纹承压强度compressive strength perpendicular to grain 横纹承压强度concentration of plastic deformation 塑性变形集中conceptual earthquake-resistant design 建筑抗震概念设计connecting plate 连接板connection 连接connections of steel structure 钢结构连接connections of timber structure 木结构连接consistency of mortar 砂浆稠度constant cross-section column 等截面柱construction and examination concentratedload 施工和检修集中荷载continuous weld 连续焊缝core area of section 截面核芯面积core tube supported structure 核心筒悬挂结构corrosion of steel bar 钢筋锈蚀coupled wall 连肢墙coupler 连接器coupling wall-beam 连梁coupling wall-column... 墙肢coursing degree of mortar 砂浆分层度cover plate 盖板covered electrode 焊条crack 裂缝crack resistance 抗裂度crack width 裂缝宽度crane girder 吊车梁crane load 吊车荷载creep of concrete 混凝土徐变crook 横弯cross beam 井字梁cup 翘弯curved support 弧形支座Ddeformation analysis 变形验算degree of gravity vertical for structure orstructural member 结构构件垂直度degree of gravity vertical forwall surface 墙面垂直度degree of plainness for structural memer 构件平整度degree of plainness for wall surface 墙面平整度depth of compression zone 受压区高度depth of neutral axis 中和轴高度design of building structures 建筑结构设计design value of earthquake-resistant strengthof materials 材料抗震强度设计值design value of load-carrying capacity ofmembers 构件承载能力设计值designations 0f steel 钢材牌号designvalue of material strength 材料强度设计值destructive test 破损试验detailing reintorcement 构造配筋detailing requirements 构造要求diamonding 菱形变形diaphragm 横隔板dimensional errors 尺寸偏差distribution factor of snow pressure 屋面积雪分布系数double component concrete column 双肢柱dowelled joint 销连接down-stayed composite beam 下撑式组合粱ductile frame 延性框架dynamic design 动态设计Eearthquake-resistant design 抗震设计earthquake-resistant detailing requirements 抗震构造要求effective area of fillet weld 角焊缝有效面积effective depth of section 截面有效高度effective diameter of bolt or high-strength bolt 螺栓或高强度螺栓有效直径effective height 计算高度effective length 计算长度effective length of fillet weld 角焊缝有效计算长度effective length of nail 钉有效长度effective span 计算跨度effective supporting length at end of beam 梁端有效支承长度effective thickness of fillet weld 角焊缝有效厚度elastic analysis scheme 弹性方案elastic foundation beam 弹性地基梁elastic foundation plate 弹性地基板elastically supported continuous girder 弹性支座连续梁elasticity modulus of materials 材料弹性模量elongation rate 伸长率embeded parts 预埋件enhanced coefficient of local bearingstrength of materials 局部抗压强度提高系数equivalent slenderness ratio 换算长细比equivalent uniformly distributed live load 等效均布活荷载etlectlve cross-section area of high-strengthbolt 高强度螺栓的有效截面积ettectlve cross-section area of bolt 螺栓有效截面面积euler's critical load 欧拉临界力euler's critical stress 欧拉临界应力Ffiller plate 填板门fillet weld 角焊缝finger joint 指接fish eye 白点fish-belly beam 角腹式梁fissure 裂缝flexible connection 柔性连接flexural rigidity of section 截面弯曲刚度flexural stiffness of member 构件抗弯刚度floor plate 楼板floor system 楼盖four sides(edgessupported plate 四边支承板frame structure 框架结构frame tube structure 单框筒结构frame tube structure 框架-简体结构frame with sidesway 有侧移框架frame without sidesway 无侧移框架frange plate 翼缘板friction coefficient of masonry 砌体摩擦系数full degree of mortar at bed joint 砂浆饱满度function of acceptance 验收函数Ggang nail plate joint 钉板连接grider 主梁grip 夹具grith weld 环形焊缝groove 坡口gusset plate 节点板Hhanger 吊环hanging steel bar 吊筋heat tempering bar 热处理钢筋height variation factor of wind pressure 风压高度变化系数heliral weld 螺旋形僻缝high-strength bolt 高强度螺栓high-strength bolt with large hexagon bea 大六角头高强度螺栓high-strength bolted bearing type join 承压型高强度螺栓连接，high-strength bolted connection 高强度螺栓连接high-strength bolted friction-type joint 摩擦型高强度螺栓连接high-strength holted steel slsteel structure 高强螺栓连接钢结构hinge support 铰轴支座hinged connection 铰接hlngeless arch 无铰拱hollow brick 空心砖hollow ratio of masonry unit 块体空心率honeycomb 蜂窝hook 弯钩hoop 箍筋hot-rolled deformed bar 热轧带肋钢筋hot-rolled plain bar 热轧光圆钢筋hot-rolled section steel 热轧型钢hunched beam 加腋梁Iimpact toughness 冲击韧性impermeability 抗渗性inclined section 斜截面inclined stirrup 斜向箍筋incomplete penetration 未焊透incomplete tusion 未溶合incompletely filled groove 未焊满indented wire 刻痕钢丝influence coefficient for load-bearingcapacity of compressionmember 受压构件承载能力影响系数influence coefficient for spacial action 空间性能影响系数initial control 初步控制inspection for properties of glue used instructural member结构用胶性能检验inspection for properties of steelbar 钢筋性能检验integral prefabricated prestressed concreteslab-column structure整体预应力板柱结构intermediate stiffener 中间加劲肋intermittent weld 断续焊缝Jjoint of reinforcement 钢筋接头Kkey joint 键连接kinetic design 动态设计knot 节子(木节)Llaced of battened compression member 格构式钢柱lacing and batten elements 缀材(缀件)lacing bar 缀条lamellar tearing 层状撕裂lap connectlon 叠接(搭接)lapped length of steel bar 钢筋搭接长度large pannel concrete structure 混凝土大板结构large-form cocrete structure 大模板结构lateral bending 侧向弯曲lateral displacement stiffness of storey 楼层侧移刚度lateral displacement stiffness of structure 结构侧移刚度lateral force resistant wallstructure 抗侧力墙体结构leg size of fillet weld 角焊缝焊脚尺寸length of shear plane 剪面长度lift-slab structure 升板结构limiting value for sectional dimension 截面尺寸限值limiting value for supporting length 支承长度限值limiting value for total height of masonrystructure 砌体结构总高度限值linear expansion coeffcient 线膨胀系数lintel 过梁load bearing wall 承重墙load-carrying capacity per bolt 单个普通螺栓承载能力load-carrying capacity per high-strength holt单个高强螺桂承载能力load-carrying capacity per rivet 单个铆钉承载能力long term rigidity of member 构件长期刚度longitude horizontal bracing 纵向水平支撑longitudinal steel bar 纵向钢筋longitudinal stiffener 纵向加劲肋longitudinal weld 纵向焊缝losses of prestress 预应力损失lump material 块体Mmain axis 强轴main beam 主梁major axis 强轴manual welding 手工焊接manufacture control 生产控制mechanical properties of materials 材料力学性能melt-thru 烧穿method of sampling 抽样方法minor axls 弱轴modified coefficient for allowable ratio ofheight to sectionalthickness of masonry wall 砌体墙容许高厚比修正系数modulus of elasticity of concrete 混凝土弹性模量modulus of elasticity parellel to grain 顺纹弹性模量moisture content 含水率moment modified factor 弯矩调幅系数monitor frame 天窗架mortar 砂浆multi-defence system of earthquake-resistantbuilding 多道设防抗震建筑multi-tube supported suspended structure 多筒悬挂结构Nnailed joint 钉连接net height 净高net span 净跨度non-destructive inspection of weld 焊缝无损检验non-destructive test 非破损检验non-load-bearingwall 非承重墙non-uniform cross-section beam 变截面粱non-uniformly distributed strain coefficientof longitudinal tensile reinforcement纵向受拉钢筋应变不均匀系数normal concrete 普通混凝土normal section 正截面notch and tooth joint 齿连接number of sampling 抽样数量Oobligue section 斜截面oblique-angle fillet weld 斜角角焊缝one-way reinforced(or prestressedconcreteslab 单向板open web roof truss 空腹屋架ordinary concrete 普通混凝土ordinary steel bar 普通钢筋orthogonal fillet weld 直角角焊缝outstanding width of flange 翼缘板外伸宽度outstanding width of stiffener 加劲肋外伸宽度over-all stability reduction coefficient ofsteel beam 钢梁整体稳定系数overturning or slip resistance analysis 抗倾覆、滑移验算Ppadding plate 垫板partial penetrated butt weld 不焊透对接焊缝partition 非承重墙penetrated butt weld 透焊对接焊缝percentage of reinforcement 配筋率pilastered wall 带壁柱墙pit 凹坑pith 髓心plain concrete structure 素混凝土结构plane hypothesis 平截面假定plane structure 平面结构plane trussed lattice grids 平面桁架系网架plank 板材plastic adaption coefficient of cross-section截面塑性发展系数plastic design of steel structure 钢结构塑性设计plastic hinge 塑性铰plastlcity coefficient of reinforced concretemember in tensile zone受拉区混凝土塑性影响系数plate-like space frame 干板型网架plate-like space truss 平板型网架plug weld 塞焊缝plywood 胶合板pockmark 麻面polygonal top-chord roof truss 多边形屋架post-tensioned prestressed concrete structure后张法预应力混凝土结构precast reinforced concrete member 预制混凝土构件prefabricated concrete structure 装配式混凝土结构presetting time 初凝时间prestressed concrete structure 预应力混凝土结构prestressed steel structure 预应力钢结构prestressed tendon 预应力筋pre-tensioned prestressed concrete structure 先张法预应力混凝土结构primary control 初步控制production control 生产控制properties of fresh concrete 可塑混凝土性能properties of hardened concrete 硬化混凝土性能property of building structural materials 建筑结构材料性能purlin 檩条Qquality grade of weld 焊缝质量级别quality inspection of bolted connection 螺栓连接质量检验quality inspection of riveted connection 铆钉连接质量检验quasi-permanent value of live load on flooror roof 楼面、屋面活荷载准永久值Rradial check 辐裂ratio of axial compressive force to axialcompressive ultimate capacity of section轴压比ratio of height to sectional thickness ofwall or column 砌体墙柱高、厚比ratio of reinforcement 配筋率ratio of shear span to effective depth ofsection 剪跨比redistribution of internal force 内力重分布reducing coefficient of compressive strengthin sloping grain for bolted connection螺栓连接斜纹承压强度降低系数reducing coefficient of liveload 活荷载折减系数reducing coefficient of shearing strength fornotch and tooth connection齿连接抗剪强度降低系数regular earthquake-resistant building 规则抗震建筑reinforcement ratio 配筋率reinforcement ratio per unit volume 体积配筋率relaxation of prestressed tendon 预应筋松弛representative value of gravity load 重力荷载代表值resistance to abrasion 耐磨性resistance to freezing and thawing 抗冻融性resistance to water penetration 抗渗性reveal of reinforcement 露筋right-angle filletweld 直角角焊缝rigid analysis scheme 刚性方案rigid connection 刚接rigid transverse wall 刚性横墙rigid zone 刚域rigid-elastic analysis scheme 刚弹性方案rigidity of section 截面刚度rigidly supported continous girder 刚性支座连续梁ring beam 圈梁rivet 铆钉riveted connecction 铆钉连接riveted steel beam 铆接钢梁riveted steel girder 铆接钢梁riveted steel structure 铆接钢结构rolle rsupport 滚轴支座rolled steel beam 轧制型钢梁roof board 屋面板roof bracing system 屋架支撑系统roof girder 屋面梁roof plate 屋面板roof slab 屋面板roof system 屋盖roof truss 屋架round wire 光圆钢丝Ssafety classes of building structures 建筑结构安全等级safetybolt 保险螺栓saw-tooth joint failure 齿缝破坏scarf joint 斜搭接seamless steel pipe 无缝钢管seamless steel tube 无缝钢管second moment of area of tranformed section 换算截面惯性矩second order effect due to displacement 挠曲二阶效应secondary axis 弱轴secondary beam 次粱section modulus of transformed section 换算截面模量section steel 型钢semi-automatic welding 半自动焊接separated steel column 分离式钢柱setting time 凝结时间shake 环裂shaped steel 型钢shapefactorofwindload 风荷载体型系数shear plane 剪面shearing rigidity of section 截面剪变刚度shearing stiffness of member 构件抗剪刚度short stiffener 短加劲肋short term rigidity of member 构件短期刚度shrinkage 干缩shrinkage of concrete 混凝干收缩silos 贮仓skylight truss 天窗架slab 楼板slab-column structure 板柱结构slag inclusion 夹渣sloping grain 斜纹slump 坍落度snow reference pressure 基本雪压solid-web steel column 实腹式钢柱space structure 空间结构space suspended cable 悬索spacing of bars 钢筋间距spacing of rigid transverse wall 刚性横墙间距spacing of stirrup legs 箍筋肢距spacing of stirrups 箍筋间距specified concrete 特种混凝上spiral stirrup 螺旋箍筋spiral weld 螺旋形焊缝split ringjoint 裂环连接square pyramid space grids 四角锥体网架stability calculation 稳定计算stability reduction coefficient of axiallyloaded compression 轴心受压构件稳定系数stair 楼梯static analysis scheme of building 房屋静力汁算方案static design 房屋静力汁算方案statically determinate structure 静定结构statically indeterminate structure 超静定结构sted 钢材steel bar 钢筋steel column component 钢柱分肢steel columnbase 钢柱脚steel fiber reinforced concrete structure 钢纤维混凝土结构steel hanger 吊筋steel mesh reinforced brick masonry member 方格网配筋砖砌体构件steel pipe 钢管steel plate 钢板steel plateelement 钢板件steel strip 钢带steel support 钢支座steel tie 拉结钢筋steel tie bar for masonry 砌体拉结钢筋steel tube 钢管steel tubular structure 钢管结构steel wire 钢丝stepped column 阶形柱stiffener 加劲肋stiffness of structural member 构件刚度stiffness of transverse wall 横墙刚度stirrup 箍筋storev height 层高straight-line joint failure 通缝破坏straightness of structural member 构件乎直度strand 钢绞线strength classes of masonry units 块体强度等级strength classes of mortar 砂浆强度等级strength classes of structural steel 钢材强度等级strength classes(grades of prestressed tendon预应力筋强度等级strength classes(grades of steel bar 普通钢筋强度等级strength of structural timber parallel tograin 木材顺纹强度strongaxis 强轴structural system composed of bar 杆系结构structural system composed of plate 板系结构structural wall 结构墙superposed reinforced concrete flexuralmember 叠合式混凝土受弯构件suspended crossed cable net 双向正交索网结构suspended structure 悬挂结构swirl grain 涡纹Ttensile(compressive) rigidity of section 截面拉伸(压缩刚度)tensile(compressive) stiffness of member 构件抗拉(抗压刚度) tensile(ultimate) strength of steel 钢材抗拉(极限强度)test for properties of concrete structuralmembers 构件性能检验thickness of concrete cover 混凝土保护层厚度thickness of mortarat bed joint 水平灰缝厚度thin shell 薄壳three hinged arch 三铰拱tie bar 拉结钢筋tie beam 系梁tie tod 系杆tied framework 绑扎骨架tor-shear type high-strength bolt 扭剪型高强度螺栓torsional rigidity of section 截面扭转刚度torsional stiffness of member 构件抗扭刚度total breadth of structure 结构总宽度total height of structure 结构总高度total length of structure 结构总长度transmission length of prestress 预应力传递长度transverse horizontal bracing 横向水平支撑transverse stiffener 横向加劲肋transverse weld 横向焊缝transversely distributed steelbar 横向分布钢筋trapezoid roof truss 梯形屋架triangular pyramid space grids 三角锥体网架triangular roof truss 三角形屋架trussed arch 椽架trussed rafter 桁架拱tube in tube structure 筒中筒结构tube structure 简体结构twist 扭弯two hinged arch 双铰拱Uunbonded prestressed concrete structure 无粘结预应力混凝土结构undercut 咬边uniform cross-section beam 等截面粱upper flexible and lower rigid complexmultistorey building 上柔下刚多层房屋upper rigid lower flexible complexmultistorey building 上刚下柔多层房屋Vvalue of decompression prestress 预应力筋消压预应力值value of effective prestress 预应筋有效预应力值verification of serviceability limit states 正常使用极限状态验证verification of ultimate limit states 承载能极限状态验证vertical bracing 竖向支撑vierendal roof truss 空腹屋架visual examination of structural member 构件外观检查visual examination of structural steel member钢构件外观检查visual examination of weld 焊缝外观检查Wwall beam 墙梁wall frame 壁式框架wall-slab structure 墙板结构warping 翘曲warping rigidity of section 截面翘曲刚度water retentivity of mortar 砂浆保水性water tower 水塔water／cement ratio 水灰比weak axis 弱轴weak region of earthquake-resistant building 抗震建筑薄弱部位web plate 腹板weld 焊缝weld crack 焊接裂纹weld defects 焊接缺陷weld roof 焊根weld toe 焊趾weldability of steel bar 钢筋可焊性welded framework 焊接骨架welded steel beam 焊接钢梁welded steel girder 焊接钢梁welded steel pipe 焊接钢管welded steel strueture 焊接钢结构welding connection 焊缝连接welding flux 焊剂welding rod 焊条welding wire 焊丝wind fluttering factor 风振系数wind reference pressure 基本风压wind-resistant column 抗风柱Yyield strength (yield point) of steel 钢筋屈服强度(屈服点)。
钢结构术语和符号(中英文对照)
钢结构术语和符号（中英文对照）一、术语1、强度：构件截面材料或连接抵抗破坏的能力。
强度计算是防止结构构件或连接因材料强度被超过而破坏的计算。
2、承载能力：结构或构件不会因强度、稳定或疲劳等因素破坏所能承受的最大内力；或塑性分析形成破坏机构时的最大内力；或达到不适应于继续承载的变形时的内力。
3、脆断：一般指钢结构在拉应力状态下没有出现警示性的塑性变形而突然发生的脆性断裂。
4、强度标准值：国家标准规定的钢材屈服点(屈服强度)或抗拉强度。
5、强度设计值：钢材或连接的强度标准值除以相应抗力分项系数后的数值。
6、一阶弹性分析：不考虑结构二阶变形对内力产生的影响，根据未变形的结构建立平衡条件，按弹性阶段分析结构内力及位移。
7、二阶弹性分析：考虑结构二阶变形对内力产生的影响，根据位移后的结构建立平衡条件，按弹性阶段分析结构内力及位移。
8、屈曲：杆件或板件在轴心压力、弯矩、剪力单独或共同作用下突然发生与原受力状态不符的较大变形而失去稳定。
9、腹板屈曲后强度：腹板屈曲后尚能继续保持承受荷载的能力。
10、通用高厚比：参数，其值等于钢材受弯、受剪或受压屈服强度除以相应的腹板抗弯、抗剪或局部承压弹性屈曲应力之商的平方根。
11、整体稳定：在外荷载作用下，对整个结构或构件能否发生屈曲或失稳的评估。
12、有效宽度：在进行截面强度和稳定性计算时宽度。
假定板件有效的那13、有效宽度系数：板件有效宽度与板件实际宽度的比值。
14、计算长度：构件在其有效约束点间的几何长度乘以考虑杆端变形情况和所受荷载情况的系数而得的等效长度，用以计算构件的长细比。
计算焊缝连接强度时采用的焊缝长度。
15、长细比：构件计算长度与构件截面回转半径的比值。
16、换算长细比：在轴心受压构件的整体稳定计算中，按临界力相等的原则，将格构式构件换算为实腹构件进行计算时所对应的长细比或将弯扭与扭转失稳换算为弯曲失稳时采用的长细比。
17、支撑力：为减小受压构件(或构件的受压翼缘)的自由长度所设置的侧向支承处，在被支撑构件（或构件受压翼缘)的屈曲方向，所需施加于该构件(或构件受压冀缘)截面剪心的侧向力。
最全的钢结构术语中英对照
最全的钢结构术语（中英对照)Aacceptable quality 合格质量acceptance lot 验收批量aciera 钢材admixture 外加剂against slip coefficient between friction surface of high-strength bolted connection 高强度螺栓摩擦面抗滑移系数aggregate 骨料air content 含气量air-dried timber 气干材allowable ratio of height to sectional thickness of masonry wall or column砌体墙、柱容许高厚比allowable slenderness ratio of steel member 钢构件容许长细比allowable slenderness ratio of timber compression member 受压木构件容许长细比allowable stress range of fatigue 疲劳容许应力幅allowable ultimate tensile strain of reinforcement 钢筋拉应变限值allowable value of crack width 裂缝宽度容许值allowable value of deflection of structural member 构件挠度容许值allowable value of deflection of timber bending member 受弯木构件挠度容许值allowable value of deformation of steel member 钢构件变形容许值allowable value of deformation of structural member 构件变形容许值allowable value of drift angle of earthquake resistant structure 抗震结构层间位移角限值amplified coefficient of eccentricity 偏心距增大系数anchorage 锚具anchorage length of steel bar 钢筋锚固长度approval analysis during construction stage 施工阶段验算arch 拱arch with tie rod 拉捍拱arch-shaped roof truss 拱形屋架area of shear plane 剪面面积area of transformed section 换算截面面积aseismic design 建筑抗震设计assembled monolithic concrete structure 装配整体式混凝土结构automatic welding 自动焊接auxiliary steel bar 架立钢筋Bbackfilling plate 垫板balanced depth of compression zone 界限受压区高度balanced eccentricity 界限偏心距bar splice 钢筋接头bark pocket 夹皮batten plate 缀板beam 次梁bearing plane of notch 齿承压面bearing plate 支承板bearing stiffener 支承加劲肋bent—up steel bar 弯起钢筋block 砌块block masonry 砌块砌体block masonry structure 砌块砌体结构blow hole 气孔board 板材bolt 螺栓bolted connection (钢结构螺栓连接bolted joint (木结构螺栓连接bolted steel structure 螺栓连接钢结构bonded prestressed concrete structure 有粘结预应力混凝土结构bow 顺弯brake member 制动构件breadth of wall between windows 窗间墙宽度brick masonry 砖砌体brick masonry column 砖砌体柱brick masonry structure 砖砌体结构brick masonry wall 砖砌体墙broad—leaved wood 阔叶树材building structural materials 建筑结构材料building structural unit 建筑结构单元building structure 建筑结构built-up steel column 格构式钢柱bundled tube structure 成束筒结构burn-through 烧穿butt connection 对接butt joint 对接butt weld 对接焊缝Ccalculating area of compression member 受压构件计算面积calculating overturning point 计算倾覆点calculation of load—carrying capacity of member 构件承载能力计算camber of structural member 结构构件起拱cantilever beam 挑梁cap of reinforced concrete column 钢筋混凝土柱帽carbonation of concrete 混凝土碳化cast-in—situ concrete slab column structure 现浇板柱结构cast-in—situ concrete structure 现浇混凝土结构cavitation 孔洞cavity wall 空斗墙cement 水泥cement content 水泥含量cement mortar 水泥砂浆characteriseic value of live load on floor or roof 楼面、屋面活荷载标准值characteristi cvalue o fwindload 风荷载标准值characteristic value of concrete compressive strength 混凝土轴心抗压强度标准值characteristic value of concrete tensile strength 混凝土轴心抗拉标准值characteristic value of cubic concrete compressive strength混凝土立方体抗压强度标准值characteristic value of earthquake action 地震作用标准值characteristic value of horizontal crane load 吊车水平荷载标准值characteristic value of masonry strength 砌体强度标准值characteristic value of permanent action 永久作用标准值characteristic value of snowload 雪荷载标准值characteristic value of strength of steel 钢材强度标准值characteristic value of strength of steel bar 钢筋强度标准值characteristic value of uniformly distributed live load 均布活标载标准值characteristic value of variable action 可变作用标准值characteristic value of vertical crane load 吊车竖向荷载标准值charaeteristic value of material strength 材料强度标准值checking section of log structural member，原木构件计算截面chimney 烟囱circular double-layer suspended cable 圆形双层悬索circular single—layer suspended cable 圆形单层悬索circumferential weld 环形焊缝classfication for earthquake-resistance of buildings 建筑结构抗震设防类别clear height 净高clincher 扒钉coefficient of equivalent bending moment of eccentrically loaded steel memher （beam—column 钢压弯构件等效弯矩系数cold bend inspection of steelbar 冷弯试验cold drawn bar 冷拉钢筋cold drawn wire 冷拉钢丝cold-formed thin-walled sectionsteel 冷弯薄壁型钢cold—formed thin-walled steel structure 冷弯薄壁型钢结构cold—rolled deformed bar 冷轧带肋钢筋column bracing 柱间支撑combination value of live load on floor or roof 楼面、屋面活荷载组合值compaction 密实度compliance control 合格控制composite brick masonry member 组合砖砌体构件composite floor system 组合楼盖composite floor with profiled steel sheet 压型钢板楼板composite mortar 混合砂浆composite roof truss 组合屋架compostle member 组合构件compound stirrup 复合箍筋compression member with large eccentricity 大偏心受压构件compression member with small eccentricity 小偏心受压构件compressive strength at an angle with slope of grain 斜纹承压强度compressive strength perpendicular to grain 横纹承压强度concentration of plastic deformation 塑性变形集中conceptual earthquake—resistant design 建筑抗震概念设计concrete 混凝土concrete column 混凝土柱concrete consistence 混凝土稠度concrete floded-plate structure 混凝土折板结构concrete foundation 混凝土基础concrete mix ratio 混凝土配合比concrete wall 混凝土墙concrete-filled steel tubular member 钢管混凝土构件conifer 针叶树材coniferous wood 针叶树材connecting plate 连接板connection 连接connections of steel structure 钢结构连接connections of timber structure 木结构连接consistency of mortar 砂浆稠度constant cross—section column 等截面柱construction and examination concentrated load 施工和检修集中荷载continuous weld 连续焊缝core area of section 截面核芯面积core tube supported structure 核心筒悬挂结构corrosion of steel bar 钢筋锈蚀coupled wall 连肢墙coupler 连接器coupling wall-beam 连梁coupling wall—column.。
钢结构专业术语英文简称与中文对照
University beam (UB)----通用梁(工字梁)University columns (UC)----通用柱Rolled steel angles (RSA)----角钢RSC----C型钢(槽钢)Rectangular hollow sections (RHS)----矩形中空型钢Square hollow sections (SHS)-----正方形中空型钢Circular hollow sections (CHS)----圆形中空型钢High strength friction GRIP (HSFG)----高强度摩擦紧固螺栓Tension control (TC)----拉力控制All flux -----合金焊剂All-weld-metal test specimen------全焊缝金属试件(完全由焊缝金属组成的缩短断面试件)Automatic welding-----自动焊接Back gouging-----清根Backing----衬垫base metal----母材Bevel angle----破口面角度Box tubing-----箱型管Butt joint ---- 对接接头Butt weld ---- 对接焊缝Cap pass ---- 盖面焊道Complete penetration ---- 完全熔透Corner joint ---- 角接接头contract documents ---- 合同文件contractor ---- 承包商contractor’s Inspector ---- 承包商检验员ESW (electroslag welding) ---- 电渣焊FCA W(flux cored arc welding) ---- 药芯焊丝电弧焊。
钢结构专业术语——中英文对照
ANCHOR BOLT LAYOUT 地脚锚栓平面布置图ANCHOR BOLT 地脚锚栓Width×Depth 槽宽×槽深Base plate 底板Column 柱子Base plate center point 底板中心点shear plates 剪力键Eave beam 屋檐梁int.beam 中间梁sidewall column 边墙柱int.column 中间柱bolted connection schedule 连接螺栓表QTY 数量Description 说明Part NO 零件图号bolt assy.connection number 螺栓组件连接号Frange Brace layout see 07-G140223 翼缘支撑见07-G140223purlin 檩条purlin brace location see 07-G140222 檩条支撑位置见07-G140222purlin location 檩条位置beam direction erection see detail CX003 梁的安装指向块见详图CX003 RIDGE LINE 屋脊中心线Frame cross section @ GRID 2 2轴框架立面图part schedule 部件表part length 部件长度field work 现场加工Note: Flange brace conn Please see cx001&cz002 翼缘支撑连接节点参照cx001&cx002 flange description 翼缘说明double brace 双支撑length 长度DIM dimension 尺寸detail no 详图图号plateROOF BRACING LAYOUT 屋面支撑布置图WALL BRACING LAYOUT@GRID A A轴墙面支撑布置图BACK-UP PLATE 背板use(4) M20×70 Grade 10.9 bolt assmbly 采用4个M20×70 10.9级的螺栓紧固。
钢结构专业术语——中英文对照
ANCHOR BOLT LAYOUT 地脚锚栓平面布置图ANCHOR BOLT 地脚锚栓Width×Depth 槽宽×槽深Base plate 底板Column 柱子Base plate center point 底板中心点shear plates 剪力键Eave beam 屋檐梁中间梁sidewall column 边墙柱中间柱bolted connection schedule 连接螺栓表QTY 数量Description 说明Part NO 零件图号bolt assy.connection number 螺栓组件连接号Frange Brace layout see 07-G140223 翼缘支撑见07-G140223purlin 檩条purlin brace location see 07-G140222 檩条支撑位置见07-G140222purlin location 檩条位置beam direction erection see detail CX003 梁的安装指向块见详图CX003 RIDGE LINE 屋脊中心线Frame cross section @ GRID 2 2轴框架立面图part schedule 部件表part length 部件长度field work 现场加工Note: Flange brace conn Please see cx001&cz002 翼缘支撑连接节点参照cx001&cx002 flange description 翼缘说明double brace 双支撑length 长度DIM dimension 尺寸detail no 详图图号plateROOF BRACING LAYOUT 屋面支撑布置图WALL BRACING LAYOUT@GRID A A轴墙面支撑布置图BACK-UP PLATE 背板use(4) M20×70 Grade 10.9 bolt assmbly 采用4个M20×级的螺栓紧固。
钢结构英文缩写及含义
构件篇COLUMN 柱子POST 从梁上升起的柱子BASE PLATE 底板CAP PLATE 顶板COVER PLATE 盖板END PLATE 封板，短板SEAL PLATE 封板SHEAR PLATE 剪切板CONNECTION PLATE 连接板BEAM 梁/次梁SECONDARY BEAM 次梁JOIST GIRDER 主桁架GIRDER 主梁JOIST 次桁架BRACE 支撑LINTEL 过梁MISC 杂件EMBED PALTE 预埋板件ANCHOR BOLT 地脚螺栓FRAME 钢架RAILING 扶手STAIR 楼梯RC WALL 混凝土墙BRACKET 马仔PART/TYP PART 零件ASSY 组合件CANOPY 雨棚CATWALK 猫道LADDER 爬梯PURLIN 檩条FISH PLATE 结合板HOIST BEAM 起吊运输梁BUILT-UP SECTION 组合截面BEARING PLATE 支撑板CANTILEVER BEAM 悬臂梁/挑梁CRANE GIRDER 吊车梁CROSS BEAM 井字梁GIRT 抗风梁RING BEAM 圈梁DIAPHRAGM 横隔板STIFFENER/STIFF 加劲板/肋GUSSET PLATE 节点板HANGER 吊杆/吊环GRIP夹具/卡子TIE BAR 拉结钢筋TIE BEAM 系梁TIE TOD 系杆TIE ROD 系杆FLANGE 翼缘/法兰WEB PLATE/WEB 腹板图纸/版本篇DESIGN DRAWING 设计图SHOP DRAWING 施工图/详图FABRICATION DRAWING 加工图ARCHITECTURE 建筑图AS-BUILT DRAWING 竣工图FOR APPROVAL 审批FOR FAB 加工UPDATE 更新FOR FIELD USED 现场使用材料篇SHS 方通/方管SQUARE HOLLOW SECTION RHS 矩形管RECTANGLE HOLLOW SECTION CHS 圆管/喉管CIRCULAR HOLLOW SECTION GMS 低碳钢GALV MILD STEELRSC 槽钢ROLLED STEEL CHANNELRSA 角钢ROLLED STEEL AMGLEHSB 高强螺栓HIGN STRENGTH BOLTCSK BOLT 沉头螺栓FLAT BAR 扁钢CHANNEL 槽钢TS 方通/方管HSS 方通/方管HOLLOW SQUARE SECTION ANGLE 角钢TC BOLT 扛剪型螺栓RB 混凝土RIVET 铆钉ROD 圆钢PLATE 板材SECTION STEEL 型钢SHAPED STEEL 型钢SEAMLESS STEEL PIPE 无缝钢管〔圆〕SEAMLESS STEEL TUBE 无缝钢管〔方〕WELDED STEEL PIPE 焊接钢管〔圆〕WELDED STEEL TUBE 焊接钢管〔方〕STEEL STRIP 钢带/带钢STEEL BELT 钢带/带钢STEEL WIRE 钢丝GRATING 格栅板EA 等边角钢EQUAL ANGLE UA 不等边角钢UNEQUAL ANGLE UC 等边工字钢UNIVERSAL COLUMNS UB 不等边工字钢UNIVERSAL BEAM PFC 方脚槽钢PARALLEL FLANGE CHANNEL焊接篇FIELD WELD 现场焊接〔美〕SITE WELD 现场焊接〔英〕SHOP WELD 工厂焊接FILLET WELD 角焊缝FPBW 完全熔透对接焊BW 对接焊FSBW 完全等强对接焊CONTINUOUS WELD 连续焊缝GRITH WELD 环形焊缝PLUG WELD 塞焊缝SLOT WELDING 槽焊缝WELDING WITH BACKING 衬垫焊STUD WELDING 螺柱焊GROOVE 坡口SEAM 接缝WELDING SYMBOL 焊缝符号THROAT 焊喉FILLET WELD LEG 焊脚FLAT FILLET 平面角焊缝CONVEX FILLET WELD 凸面角焊缝CONCAVE FILLET WELD 凹面角焊缝STAGGERED INTERMITTENT FILLET WELD 交错断续角焊缝CHAIN INTERMITTENT FILLET WELD 并列断续角焊缝SEAL WELD 密封焊缝STRENGTH WELD 承载焊缝CONNECTIVE WELD 联系焊缝QUALITY GRADE OF WELD 焊缝质量级别VISUAL EXAMINATION OF STRUCTURAL MEMBER 构件外观检查VISUAL EXAMINATION OF WELD 焊缝外观检查(VT)WELD PROCESS 焊接过程WELD TECHNIQUE 焊接技术TECHNOLOGY/PROCEDURE 焊接工艺WELDING OPERATION 焊接操作WELDING SEQUENCE 焊接顺序FILLET WELDING 角焊缝GROOVE WELDING 坡口焊TACK WELDING 定位焊CONTINUOUS WELDING 连续焊INTERMITTENT WELDING 断续焊BRACKING WELDING 打底焊工序篇CUT 切割COPE 切割HDG 热浸锌FINGER TIGHTEN 手拧DRILL HOLES 钻孔FABRICATION PROCEDURE 制作顺序PREPARATION FOR FABRICATION 制作准备CUTTING WORKS 下料GALVANIZING PROCESS 镀锌程序REPAIRING GALVANIZING SURFACE 镀锌后外表修复TAP 攻丝SIZE DIMENSION 定形尺寸LOCATION DIMENSION 定位尺寸视图篇PLAN ELEVATION 平面图立面图VIEW 视图LAYOUT PLAN 平面布置图ROOF FRAMING 屋面平面图THREE-VIEW DRAWING 三视图FRONTAL VIEW 前视图，主视图TOP VIEW 俯视图LEFT/RIGHT SIDE VIEW 左视图/右视图REAR VIEW/BACK VIEW 后视图BOTTOM VIEW 仰视图PARTIAL VIEW 局部视图SECTION/SECTION VIEW 剖面/剖视图FULL VIEW 全视图HALF VIEW 半视图DEVELOPMENT 展开图SKETCH 草图SYMMETRY 对称END VIEW 侧视图/端视图DETAIL 细部放大图杂项篇PCS NOS AS REQ’D PER 件件根据需要/如果需要根据RFI 问题联系单CONNECTION DETAIL 连接节点JOBSITE/SITE 现场MOMENT CONNECTION 刚性连接RIGID CONNECTION 刚性连接SLOPE 坡度/斜度OBLIQUE 倾斜的螺栓篇THREAD 螺纹EXTERNAL THREAD 外螺纹INTERNAL THREAD 内螺纹SCREW 螺钉/螺丝自攻螺钉TAPPING SCREW 螺母NUT HEXAGON NUT 六角螺母SQUARE NUT 方螺母ROUND NUT 圆螺母HOOK BOLT 勾头螺栓WELDING STUD 剪力钉TORQUE BOLT 扭剪螺栓STUD BOLT 双头螺栓ASSEMBLED BOLT 组合螺栓FLANGE NUT 法兰螺母CAP NUT 盖形螺母PLAIN(FLAT) WASHER 平垫SPRING WASHER 弹簧垫圈WEDGE WASHER 楔形垫圈PLATE WASHER 大垫圈说明篇UNO/TYP UNO 除非有特殊说明〔如有其它说明，则以其它说明为准〕TYP 典型的NS/NS ONLY 仅近端/正面有FS/FS ONLY 仅远端/反面有BS 正反面都有NS&FS 正反面都有。
钢结构英文缩写及含义
钢结构英文缩写及含义构件篇COLUMN 柱子POST 从梁上升起的柱子BASE PLATE 底板CAP PLATE 顶板COVER PLATE 盖板END PLATE 封板，短板SEAL PLATE 封板SHEAR PLATE 剪切板CONNECTION PLATE 连接板BEAM 梁/次梁SECONDARY BEAM 次梁JOIST GIRDER 主桁架GIRDER 主梁JOIST 次桁架BRACE 支撑LINTEL 过梁MISC 杂件EMBED PALTE 预埋板件ANCHOR BOLT 地脚螺栓FRAME 钢架RAILING 扶手STAIR 楼梯RC WALL 混凝土墙BRACKET 马仔PART/TYP PART 零件ASSY 组合件CANOPY 雨棚CATWALK 猫道LADDER 爬梯PURLIN 檩条FISH PLATE 结合板HOIST BEAM 起吊运输梁BUILT-UP SECTION 组合截面BEARING PLATE 支撑板CANTILEVER BEAM 悬臂梁/挑梁CRANE GIRDER 吊车梁CROSS BEAM 井字梁GIRT 抗风梁RING BEAM 圈梁DIAPHRAGM 横隔板STIFFENER/STIFF 加劲板/肋GUSSET PLATE 节点板HANGER 吊杆/吊环GRIP夹具/卡子TIE BAR 拉结钢筋TIE BEAM 系梁TIE TOD 系杆TIE ROD 系杆FLANGE 翼缘/法兰WEB PLATE/WEB 腹板图纸/版本篇DESIGN DRAWING 设计图SHOP DRAWING 施工图/详图FABRICATION DRAWING 加工图ARCHITECTURE 建筑图AS-BUILT DRAWING 竣工图FOR APPROVAL 审批FOR FAB 加工UPDATE 更新FOR FIELD USED 现场使用材料篇SHS 方通/方管SQUARE HOLLOW SECTION RHS 矩形管RECTANGLE HOLLOW SECTIONCHS 圆管/喉管CIRCULAR HOLLOW SECTIONGMS 低碳钢GALV MILD STEELRSC 槽钢ROLLED STEEL CHANNELRSA 角钢ROLLED STEEL AMGLEHSB 高强螺栓HIGN STRENGTH BOLTCSK BOLT 沉头螺栓FLAT BAR 扁钢CHANNEL 槽钢TS 方通/方管HSS 方通/方管HOLLOW SQUARE SECTION ANGLE 角钢TC BOLT 扛剪型螺栓RB 混凝土RIVET 铆钉ROD 圆钢PLATE 板材SECTION STEEL 型钢SHAPED STEEL 型钢SEAMLESS STEEL PIPE 无缝钢管（圆）SEAMLESS STEEL TUBE 无缝钢管（方）WELDED STEEL PIPE 焊接钢管（圆）WELDED STEEL TUBE 焊接钢管（方）STEEL STRIP 钢带/带钢STEEL BELT 钢带/带钢STEEL WIRE 钢丝GRATING 格栅板EA 等边角钢EQUAL ANGLE UA 不等边角钢UNEQUAL ANGLE UC 等边工字钢UNIVERSAL COLUMNS UB 不等边工字钢UNIVERSAL BEAM PFC 方脚槽钢PARALLEL FLANGE CHANNEL焊接篇FIELD WELD 现场焊接（美）SITE WELD 现场焊接（英）SHOP WELD 工厂焊接FILLET WELD 角焊缝FPBW 完全熔透对接焊BW 对接焊FSBW 完全等强对接焊CONTINUOUS WELD 连续焊缝GRITH WELD 环形焊缝PLUG WELD 塞焊缝SLOT WELDING 槽焊缝WELDING WITH BACKING 衬垫焊STUD WELDING 螺柱焊GROOVE 坡口SEAM 接缝WELDING SYMBOL 焊缝符号THROAT 焊喉FILLET WELD LEG 焊脚FLAT FILLET 平面角焊缝CONVEX FILLET WELD 凸面角焊缝CONCAVE FILLET WELD 凹面角焊缝STAGGERED INTERMITTENT FILLET WELD 交错断续角焊缝CHAIN INTERMITTENT FILLET WELD 并列断续角焊缝SEAL WELD 密封焊缝STRENGTH WELD 承载焊缝CONNECTIVE WELD 联系焊缝QUALITY GRADE OF WELD 焊缝质量级别VISUAL EXAMINATION OF STRUCTURAL MEMBER 构件外观检查VISUAL EXAMINATION OF WELD 焊缝外观检查(VT)WELD PROCESS 焊接过程WELD TECHNIQUE 焊接技术TECHNOLOGY/PROCEDURE 焊接工艺WELDING OPERATION 焊接操作WELDING SEQUENCE 焊接顺序FILLET WELDING 角焊缝GROOVE WELDING 坡口焊TACK WELDING 定位焊CONTINUOUS WELDING 连续焊INTERMITTENT WELDING 断续焊BRACKING WELDING 打底焊工序篇CUT 切割COPE 切割HDG 热浸锌FINGER TIGHTEN 手拧DRILL HOLES 钻孔FABRICATION PROCEDURE 制作顺序PREPARATION FOR FABRICATION 制作准备CUTTING WORKS 下料GALVANIZING PROCESS 镀锌程序REPAIRING GALVANIZING SURFACE 镀锌后表面修复TAP 攻丝SIZE DIMENSION 定形尺寸LOCATION DIMENSION 定位尺寸视图篇PLAN ELEVATION 平面图立面图VIEW 视图LAYOUT PLAN 平面布置图ROOF FRAMING 屋面平面图THREE-VIEW DRAWING 三视图FRONTAL VIEW 前视图，主视图TOP VIEW 俯视图LEFT/RIGHT SIDE VIEW 左视图/右视图REAR VIEW/BACK VIEW 后视图BOTTOM VIEW 仰视图PARTIAL VIEW 局部视图SECTION/SECTION VIEW 剖面/剖视图FULL VIEW 全视图HALF VIEW 半视图DEVELOPMENT 展开图SKETCH 草图SYMMETRY 对称END VIEW 侧视图/端视图DETAIL 细部放大图杂项篇PCS NOS AS REQ’D PER 件件根据需要/如果需要根据RFI 问题联系单CONNECTION DETAIL 连接节点JOBSITE/SITE 现场MOMENT CONNECTION 刚性连接RIGID CONNECTION 刚性连接SLOPE 坡度/斜度OBLIQUE 倾斜的螺栓篇THREAD 螺纹EXTERNAL THREAD 外螺纹INTERNAL THREAD 内螺纹SCREW 螺钉/螺丝自攻螺钉TAPPING SCREW 螺母NUT HEXAGON NUT 六角螺母SQUARE NUT 方螺母ROUND NUT 圆螺母HOOK BOLT 勾头螺栓WELDING STUD 剪力钉TORQUE BOLT 扭剪螺栓STUD BOLT 双头螺栓ASSEMBLED BOLT 组合螺栓FLANGE NUT 法兰螺母CAP NUT 盖形螺母PLAIN(FLAT) WASHER 平垫SPRING WASHER 弹簧垫圈WEDGE WASHER 楔形垫圈PLATE WASHER 大垫圈说明篇UNO/TYP UNO 除非有特殊说明（如有其它说明，则以其它说明为准）TYP 典型的NS/NS ONLY 仅近端/正面有FS/FS ONLY 仅远端/反面有BS 正反面都有NS&FS 正反面都有。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
University beam (UB)----通用梁(工字梁)
University columns (UC)----通用柱
Rolled steel angles (RSA)----角钢
RSC----C型钢(槽钢)
Rectangular hollow sections (RHS)----矩形中空型钢
Square hollow sections (SHS)-----正方形中空型钢
Circular hollow sections (CHS)----圆形中空型钢
High strength friction GRIP (HSFG)----高强度摩擦紧固螺栓
Tension control (TC)----拉力控制
All flux -----合金焊剂
All-weld-metal test specimen------全焊缝金属试件(完全由焊缝金属组成的缩短断面试件)
Automatic welding-----自动焊接
Back gouging-----清根
Backing----衬垫
base metal----母材
Bevel angle----破口面角度
Box tubing-----箱型管
Butt joint ---- 对接接头
Butt weld ---- 对接焊缝
Cap pass ---- 盖面焊道
Complete penetration ---- 完全熔透
Corner joint ---- 角接接头
contract documents ---- 合同文件
contractor ---- 承包商
contractor’s Inspector ---- 承包商检验员
ESW (electroslag welding) ---- 电渣焊
FCA W(flux cored arc welding) ---- 药芯焊丝电弧焊。