CCNA第二学期期末考试Exam
CCNA期末考试试题
1、要求:(1)VTP域名为benet;密码为123;启用修剪;(2)配置2台3层交换机为VTP的server模式;配置2层交换机为VTP的client模式;(3)设置SW-3L-1是VLAN 2－6的生成树根网桥;设置SW-3L-2是VLAN 7－11的生成树根网桥;在2层交换机上配置速端口与上行速链路;(4)配置路由器接口的IP地址;配置路由器启动RIP路由协议;配置路由器上的默认路由，指向10.1.1.1/24;(5)在3层交换机上配置各VLAN的IP地址;配置两台3层交换机之间的EthernetChannel;(6)配置3层交换机的路由接口;在3层交换机上配置RIP路由协议（1）（2）○1SW1-3L 配置vtp域名benetpassword 123 Server模式SW2-3L同样配置○2SW1-3L启用修剪SW2-3L同样配置○3SW3-2L配置vtp的client模式、SW4-2L、SW5-3L、SW6-3L相同配置（3）设置SW-3L-1是VLAN 2－6的生成树根网桥;设置SW-3L-2是VLAN 7－11的生成树根网桥;在2层交换机上配置速端口与上行速链路;○1SW-3L-1是VLAN 2－6的生成树根网桥;;○2设置SW-3L-2是VLAN 7－11的生成树根网桥○3SW3-2L配置速端口与上行链路，SW4-2L、SW5-2L 、SW6-2L上同样配置（4）配置路由器接口的IP地址;配置路由器启动RIP路由协议;配置路由器上的默认路由，指向10.1.1.1/24○1路由器上配置ip地址○2路由器上配置默认路由和RIP○3SW1-3L各vlan的ip地址○4SW2-3L各vlan的ip地址（5）在3层交换机上配置各VLAN的IP地址;配置两台3层交换机之间的EthernetChannel ○1在SW1-3L配置EthernetChannel;○2在SW2-3L配置EthernetChannel;（6）配置3层交换机的路由接口;在3层交换机上配置RIP路由协议○1SW1-3L上配置路由接口○2SW2-3L上配置路由接口○3SW1-3L上的RIP配置○4SW2-3L上的RIP配置○5在SW1-3L验证RIP○6在SW2-3L验证RIP2、要求:如图所示，四台路由器R1，R2，R3以及R4运行OSPF协议（要求发布各路由器的loopback0地址），R1与R2属于Area1，R2与R3属于Area0，R3与R4属于Area2。
CCNA2final期末考试答案A
CCNA2final期末考试答案A1.A technician configures the Fa0/0 interface on a router with ip address 192.168.3.5 255.255.255.252. What additional comma issued by the technician to activate the interface to forward traffic?Router(config-if)# exitRouter(config-if)# no shutdownRouter(config-if)# clock rateRouter# copy running-config startup-config2Refer to the exhibit. A technician has configured the interfaces on the Router, but upon inspection discovers that interface FastEthernet0/1 is not functioning. Which action will most likely correct the problem with FastEthernet0/1?A clock rate should be added to the interface configuration.The subnet mask should be added to the interface configuration.An interface description needs to be added to the interface configuration.The no shutdown command needs to be added to the interface configuration.3Refer to the exhibit. A router interface is configured with the command ip address 172.16.3.31 255.255.192.0. Which set o values would allow a computer that is connected to the router interface to communicate with remote networks?A: 172.16.3.254B: 255.255.192.0C: 172.16.3.31A: 172.16.3.31B: 255.255.192.0C: 172.16.3.255A: 172.16.3.254B: 255.255.255.0C: 172.16.3.31A: 172.16.3.31B: 255.255.255.0C: 172.16.3.14Refer to the exhibit. On the basis of the show running-config output, which option correctly reflects the routes that will be l routing table?ssss5Refer to the exhibit. PC1 is unable to access the Internet. What is the cause of the problem?An incorrect IP address is configured between the two routers.No static route is configured on Router2.A routing loop has occurred.No routing protocol is configured on either of the two routers.Refer to the exhibit. Which three statements are true of the routing table for Router1? (Choose three.)The route to network 172.16.0.0 has an AD of 156160.Network 192.168.0.16 can best be reached using FastEthernet0/0.The AD of EIGRP routes has been manually changed to a value other than the default value.Router1 is running both the EIGRP and OSPF routing process.Network 172.17.0.0 can only be reached using a default route.No default route has been configured.7Refer to the exhibit. The network has three connected routers: R1, R2, and R3. The routes of all three routers are displaye are operational and pings are not blocked on this network.Which ping will fail?from R1 to 172.16.1.1from R1 to 192.168.3.1from R2 to 192.168.1.1from R2 to 192.168.3.18Refer to the exhibit. A network administrator has configured OSPF using the following command:network 192.168.1.32 0.0.0.31 area 0Which router interface will participate in OSPF?FastEthernet0/0FastEthernet0/1Serial0/0/0Serial0/0/19Refer to the exhibit. The hosts on the R1 LAN are unable to access the Internet. What is incorrectly configured?the IP address of the Fa0/0 interface at R1the IP address of the S0/0/1 interface at R2the IP address of the S0/0/0 interface at R1the subnet mask of the S0/0/1 interface at R210Refer to the exhibit. Host A is having problems accessing server A. All routers have the same EIGRP configuration as rou What should be done so that host A can access server A?Add the command no auto-summary on all routers.Change the network statements to include a wildcard mask.Adjust the EIGRP hello timers to account for the network delay.Add the command eigrp log-neighbor-changes on all routers.Which feature of RIPv2 enables it to function as a classless routing protocol?Subnet masks are included in routing updates.Routing updates are triggered by topology changes.Next-hop addresses are included in routing updates.Multicast addresses are used to send routing updates.12A network administrator must use the subnet 172.16.128.0/18 to create 6 additional subnets each containing up to 2000 h LANs. Which subnet mask should the administrator use to create the new subnets?255.255.224.0255.255.240.0255.255.248.0255.255.252.013 A network administrator is in charge of two separate networks that share a single building. What device will be required to two networks and add a common connection to the Internet that can be shared?hubrouteraccess pointEthernet switch14Refer to the exhibit. What needs to be done to allow these two routers to connect successfully?Add a clock rate to S0/0/0 on R1.Add an interface description to S0/0/1 on R2.Change the serial interface on R2 to S0/0/0 so that it matches R1.Change the IP address of S0/0/1 on R2 so that it is in the same subnet as R1.15In which situation would a default static route be recommended?when connecting an edge router to the Internetwhen variable length subnet masking is in effectwhen there is more than one valid route for a destination networkwhen a destination network has a larger mask than any routes in the routing tableRefer to the exhibit. A network engineer has run the show version command on R3. Upon rebooting, R3 does not load th configuration settings.What could be the cause of this problem?There is insufficient NVRAM.There is insufficient flash memory.The configuration register is not configured with the default setting.The system image file is not located in NVRAM.17Refer to the exhibit. Host A is unable to access the Internet. What is the reason for this?The IP address of host A is incorrect.The default gateway of host A is incorrect.The Fa0/1 interfaces of the two routers are configured for different subnets.The subnet mask for the Fa0/0 interface of R1 is incorrect.18Refer to the exhibit. R1 and R2 are adjacent routers both running RIP. All interfaces on both routers are correctly configur operational. Both routers are configured to include all connected interfaces in routing updates. R2 is not showing any rout the routing table. What is the likely cause?The adjacent interfaces are passive.The distance of 120 exceeds 15 hops.19W hich two technologies can be used in distance vector routing protocols to prevent routing loops? (Choose two.)authenticationlink-state advertisementshold-down timersSpanning Tree Protocolsplit horizon20Which prompt is used to allow a user to change the IP address of an interface on a router?Router>Router#Router(config)#Router(config-if)#Refer to the exhibit. A network administrator adds this command to router R1: ip route 192.168.2.0 255.255.255.0 S0/0/0 result of adding this command?This route is automatically propagated throughout the network.The traffic for network 172.16.1.0 is forwarded to network 192.168.2.0.A static route is established.The traffic for all Class C networks is forwarded to 172.16.1.2.22Refer to the exhibit. What information can be determined from the displayed output?EIGRP packets are waiting to be sent to the neighbors.The adjacencies between the routers are yet to be established.The IP address 192.168.10.10 is configured at serial interface S0/0/1 of router R2.Router R2 is receiving hello packets from a neighbor with the IP address 192.168.10.10 via the R2 S0/0/1 interface.23Refer to the exhibit. Based on the partial output in the exhibit, why can users establish a console connection to this router entering a password?The login command was not entered on the cons ole line.The enable password should be an enable secret password.No username and password combination has been configured.Console connections cannot be configured to require users to provide passwords.24W hich of the following are primary functions of a router? (Choose two.)packet switchingmicrosegmentationdomain name resolutionpath selectionflow control25Because of a topology change, the next hop IP address in the current static route must be reconfigured. How can a static altered to accommodate a topology change?Negate the existing static route and configure a new static route with the correct next hop IP address.Do nothing. The existing static route will automatically update the next hop entry with the new IP address.Keep the existing static route, reload the router, and configure a new static route with the correct next hop IP addresRefer to the exhibit. All routers are configured with no auto-summary. All routers have a default route via their Serial0/1 Router B receives a packet with a destination of 10.16.1.98. What path will the packet take?B-EB-E-D-AB-E-D-A then loop A-D-A until the TTL expiresB will immediately drop the packet.There is insufficient information to answer the question.27Refer to the exhibit. A network administrator is investigating why data packets with destination addresses of 172.16.10.10 192.168.10.100 are being dropped instead of being forwarded via the static route as expected. After confirming that the ip command has been applied on all routers in the network, what other action should the administrator take to ensure that da these addresses are forwarded via the static route?Check that all routers are configured with the same autonomous system number.Issue the no auto-summary command within the EIGRP configuration of all routers.Issue the no passive-interface command within the EIGRP configuration of all routers.Configure the static route to point to the next hop address instead of the outbound interface.28If a router is booting with its default configuration register setting and its NVRAM lacks boot system commands, from whe router try to load the IOS image first?ROMRAMNVRAMflashTFTP server29T wo routers need to be configured within a single OSPF area. Which two components need to be configured on both rout this? (Choose two.)the same process IDthe same area IDnetwork addresses and wildcard masksthe same router IDthe same loop back address30Refer to the exhibit. Packets destined to which two networks will require the router to perform a recursive lookup? (Choos10.0.0.0/864.100.0.0/16128.107.0.0/16172.16.40.0/24192.168.1.0/24192.168.2.0/24Which candidate route has the longest match for a packet with a destination address of 10.30.16.48?10.30.0.0/1610.30.15.0/2310.30.16.0/2410.30.16.32/2710.30.16.32/3032W hich three statements are true regarding the encapsulation and de-encapsulation of packets when traveling through a r (Choose three.)The router modifies the TTL field, decrementing it by one.The router changes the source IP to the IP of the exit interface.The router maintains the same source and destination IP.T he router changes the source physical address to the physical address of the exit interface.The router changes the destination IP to the IP of the exit interface.The router sends the packet out all other interfaces, besides the one it entered the router on.33Refer to the exhibit. The interfaces of all routers are configured for OSPF area 0. R3 can ping R1, but the two routers are establish a neighbor adjacency. What should the network administrator do to troubleshoot this problem?Check if the interfaces of the routers are enabled.Check the hello and dead intervals between the routers.Check the process ID of both routers.Check if CDP is enabled on all the routers.34W hich mechanism helps to avoid routing loops by advertising a metric of infinity?route poisoningsplit horizonhold-down timertriggered updates35Refer to the exhibit. A device is required to complete the connection between router R1 and the WAN. Which tw o devices for this? (Choose two.)a CSU/DSU devicea modeman Ethernet switcha huba bridge36Why is fast convergence desirable in networks that use dynamic routing protocols?Hosts are unable to access their gateway until the network is converged.Routers will not allow packets to be forwarded until the network is converged.Routers may make incorrect forwarding decisions until the network has converged.Routers will not allow configuration changes to be made until the network has converged.37Refer to the exhibit. R1 is configured properly for a single area OSPF, and R2 has been recently installed in the network. commands is required to configure a single area OSPF for the networks that are connected to R2?R2(config)# router ospf 1R2(config-router)# network 192.168.2.0 0.0.0.255 area 0R2(config-router)# network 10.1.1.0 0.0.0.3 area 0R2(config)# router ospf 1R2(config-router)# network 192.168.2.0 0.0.0.255 area 0R2(config)# router ospf 2R2(config-router)# network 10.1.1.0 0.0.0.3 area 0R2(config)# router ospf 1R2(config-router)# network 192.168.2.0 0.0.0.255 area 0R2(config-router)# network 10.1.1.0 0.0.0.3 area 1R2(config)# router ospf 1R2(config-router)# network 192.168.2.0 0.0.0.255 area 0R2(config-router)# network 10.0.0.0 0.0.0.3 area 138。
CCNA2PracticeFinalExamAnswerV3.1
CCNA2PracticeFinalExamAnswerV3.11. Which statements are true regarding VTY passwords? (Choose two.)VTY passwords must be encrypted.All VTY lines do not need to use the same password.A VTY password is required to establish telnet sessions.The VTY password is set with the command line console 0.The VTY password must be identical with the enable secret password. 2.Refer to the network and routing table entries shown in the graphic. What will happen when a packet destined for network 192.66.7.0 is received by Router A?It will be forwarded through interface S1.It will be forwarded to the default route.It will be directed toward the Internet.It will be discarded.3.Which command will produce the output shown in the graphic?show cdpshow cdp neighborsshow cdp neighbors detailshow cdp detail4.Router B received an interface configuration change. Suddenly, it transmits a new update. Which of the following could have triggered this update? (Choose two.)Router B received a configuration change.Router A sent a message requesting an update.Router C came online after Router B sent the RIP update.Router B received an error message indicating the last update was not received.5. How many Telnet sessions can take place simultaneously on a router running a standard edition of the IOS?458106. Which of the following WAN connection services typically use synchronous communications? (Choose two.)circuit-switchedleased linepacket-switchedEthernetanalog modem services7. Which of the following will add a TFTP server as a fallback source fora router to load an IOS image?Router# boot system tftp 163.150.9.31 c2500-d-l.120-9Router# copy run startRouter# boot system tftp c2500-d-l.120-9.bin 163.150.9.31Router# copy run startRouter# config tRouter(config)# boot system tftp c2500-d-l.120-9.bin 163.150.9.31 Router(config)# exitRouter# copy run startRouter# config tRouter(config)# boot system tftp 163.150.9.31 c2500-d-l.120-9.binRouter(config)# exitRouter# copy run start8. What types of messages are sent periodically by devices configured for CDP?probesbeaconssignalsadvertisementsrouting updatesunicast9. An administrator has made routing protocol changes to a ro uter’s configuration. To ensure that the changes are implemented, the active configuration is saved and the router is reloaded. After the router has initialized, the output on the screen displays "Would you like to enter the initial configuration dialog?[yes/no]:" Why did this dialog appear?There was a POST failure.The incorrect IOS loaded.There was an error in the startup configuration file.The configuration register was set to ignore NVRAM.10. Which command is used to redirect debug information to a device that is connected though a Telnet session? Router# monitorRouter# terminal redirect vty 0Router# terminal monitorRouter# monitor output vty 011. After issuing the show interfaces command, a technician notices the line "Serial1 is down, line protocol is down" in the output. Which of the following are possible reasons for this message output? (Choose three.)There is a mismatch in the encapsulation type on both ends of the link.A Layer 1 issue exists.An interface problem exists.The clockrate was not set during configuration.There is no usable media for the protocol.Keepalive messages are not being sent.12.Refer to the above graphic. When using RIP as the routing protocol, how would Chicago use load balancing to route packets to New York? (Choose two.)by forwarding packets over paths of equal costby forwarding packets according to hop count and speed of the linkby determining which interface has the least traffic and sending to it firstby first determining the speed of the links and then cycling packets through the fastest links firstby cycling packets through interfaces and routes following the same pattern (Router 1, 2, 3) each time13. When would the ROM monitor mode be used? (Choose two.) maintaining routing configuration settingsmodifying the IOS image stored in Flashrunning a limited IOS feature setperforming the bootstrap process14. Which two statements are true about route metrics? (Choose two.)The more factors that make up a metric, the greater the flexibility to tailor network operations.The larger the metric number, the better the path.Routing protocols use metrics to send routing updates to directly connected neighbors.Bandwidth and delay are static metrics used by RIP v1.Ticks, delay, and cost are metrics used by routing protocols.15.Which of the following are valid static IP routes? (Choose three.) RouterB(config)# ip route 192.168.5.0 255.255.255.0 S1 RouterC(config)# ip route 192.168.1.0 255.255.255.0 S1RouterA(config)# ip route 192.168.3.0 255.255.255.0 192.168.2.2 RouterB(config)# ip route 192.168.1.0 255.255.255.0 192.168.2.2 RouterC(config)# ip route 192.168.2.0 255.255.255.0 192.168.4.1 RouterA(config)# ip route 192.168.4.0 255.255.255.0 192.168.2.116. Of the eight network users on the Human Resources department LAN, one cannot connect to the file serv er. The user’s PC has successfully booted but can not see the network. What should be checked first?the PC power cordthe file serverthe PC network interface card LEDsthe LAN switch in the wiring closetthe configuration of the router interface attached to the LAN17. What can be determined from the partial output of the show ip route command displayed below? (Choose two.)R 200.200.200.0/24 [120/1] via 192.168.10.2, 00:00:14, Serial0/0C 192.168.10.0/24 is directly connected, Serial0/0The next update will be in 76 seconds.The next update will be in 16 seconds.The administrative distance is 120 and the metric is 1.The metric is 120 and the administrative distance is 1.200.200.200.0 is configured on Serial0/0.192.168.10.2 is configured on Serial0/0.18. Why is it useful to have an interface description?A user can telnet to the router using the interface description.The interface description is a shortcut way to edit the running-config. The interface description helps identify distant network connections.The interface will remain inactive until an interface description is applied.19.Assume OSPF is being used on all routers. What happens when the link between Router1 and Router2 goes down? (Choose two.)Updates start broadcasting every 30 seconds.Updates start broadcasting every 90 seconds.Link-state advertisements are flooded.Link-state advertisements are sent only to neighboring routers.All routers note the change and adjust routes.All routers ignore the change until the route becomes active again. 20.The internetwork needs to communicate between the hosts connected to the E0 interface of the Utah router and hosts connected to the E0 interface of the Idaho router. The hosts should also have connectivity to the Internet. Which commands must be configured in order to enable this communication? (Choose three.)Idaho(config)# ip route 172.31.1.0 255.255.255.0 172.31.2.1Idaho(config)# ip route 0.0.0.0 0.0.0.0 s0Idaho(config)# ip route 172.31.2.0 255.255.255.0 172.31.2.2Utah(config)# ip route 172.31.3.0 255.255.255.0 172.31.2.1Utah(config)# ip route 172.31.3.0 255.255.255.0 s1Utah(config)# ip route 0.0.0.0 0.0.0.0 s021. Which statement about datagram life is true?Each router increments the TTL value of the datagram until the maximum hop count of the routing protocol is reached. The packet is then returned to the source.The packet is dropped when the router count and the TTL value match. The source is notified that transmission has failed. Each router decreases the TTL value by one until it reaches zero. The datagram is then discarded and a time exceeded for message is sent to the source.The destination device discards the datagram if the TTL value is zero on arrival. An ICMP destination unreachable message is sent back to the source.22.The following access list has been created to prevent traffic from host 204.204.7.122 from accessing the 201.100.11.0 network.access-list 22 deny host 204.204.7.122access-list 22 permit anyWhich group of commands will properly place this access list so that this host is denied access only to the 201.100.11.0 network?RouterA(config)# interface s0/0RouterA(config-if)# ip access-group 22 inRouterA(config)# interface s0/0RouterA(config-if)# ip access-group 22 outRouterA(config)# interface fa0/0RouterA(config-if)# ip access-group 22 inRouterB(config)# interface fa0/0RouterB(config-if)# ip access-group 22 inRouterB(config)# interface s0/0RouterB(config-if)# ip access-group 22 inRouterB(config)# interface fa0/0RouterB(config-if)# ip access-group 22 out23. A network administrator can establish a remote session to a host using the Router> telnet 192.168.1.1command but is unsuccessful when using the Router> telnet Boston command to connect to the same interface. Which of the following could be the problem? (Choose two.)The ip host table on the router is not configured.The command telnet Boston was issued from the wrong router prompt.The routing table is missing.Domain name services are not available.24. Which of the following are functions of a router? (Choose three.)packet switchingextension of network segmentssegmentation of local area networksselection of best path based on a logical addressingselection of best path based on a physical addressingThe commands shown in the graphic were entered to alter the startup sequence of the router. On the next reload, which IOS will be loaded?The router will load c2500-js-l.112-26d.The router will load c2500-d-l.120-9.The router will load the IOS from ROM.The router will boot into ROM monitor mode.26.A network administrator trying to deny Telnet traffic from the 192.5.5.0 network to the 201.100.11.0 network entered the commands shown in the graphic. When monitoring the network, the administrator noticed that Telnet packets were still passing between those networks. What is the cause?The router ignored this type of traffic because it required a standard access list to be configured instead of an extended one. The wrong port was configured for the ACL so Telnet traffic was still allowed.The access list has not been assigned to an interface.The permit ip any any allowed all traffic to pass regardless of the other statements listed in this ACL.Refer to the network graphic. A packet needs to travel from Router F to Router A. Which path would be selected by the RIP routing protocol if the default metrics are used?F, G, E, D, B, AF, E, D, C, AF, E, D, AF, E, D, B, A28. Which of the following is the correct flow of routines for a router startup?load bootstrap, load IOS, apply configurationload bootstrap, apply configuration, load IOSload IOS, load bootstrap, apply configuration, check hardwarecheck hardware, apply configuration, load bootstrap, load IOS29. In the configuration register value 0×2104, which value represents the boot field setting?x2430. ACL statements operate in sequential, logical order. If a condition match is true, the rest of the ACL statements are not checked. If all of the ACL statements are unmatched, what happens to the packet?The packets will be placed in a buffer and forwarded when the ACL is removed.The packets will be sent to the source with an error notification message.The implicit permit any statement placed at the end of the list will allow the packets to flow through uninhibited.The implicit deny any statement placed at the end of the list will cause the packets to be dropped.31. Which of the following would cause the "Message Of The Day" banner to appear? (Choose three.)telnetting into the routerinitiating a debug sessionconfiguring a router for the first timeusing the Aux port to check the current configurationusing the console port to check the current configuration32.The administrator knows that port E0 on router B connects to a small LAN without any routers. Which command can be executed on router B to conserve bandwidth on port E0?no update timersholdown-timer 96poison reverse E0passive-interface E0no triggered updates33. When must a router serial interface be configured with the clock rate command?when the interface is functioning as a DTE devicewhen the interface timers have been clearedwhen the connected DTE device is shut downwhen the interface is functioning as a DCE device34. What are the major characteristics of a wide area network? (Choose three.)connect devices separated by wide geographical areasincludes technologies of FDDI and Ethernetuses serial connections to access bandwidthcommon carriers are needed for connectionstype of connection between a router and a switch35. If the config-register on a router is set to 0×2102, where is the first place the router will look for boot system commands? RAMROMFlashNVRAM36. Why would an administrator use the Telnet application when troubleshooting a network? (Choose three.)It can be used to verify the operation of application layer software between the source and destination.Telnet can use the ICMP protocol to verify a hardware connection and network layer address.It is the most complete testing mechanism available.Remote networks may be accessed via a Telnet session for troubleshooting.Time to Live values are used by Telnet to identify a failure of device between source and destination.37.The network shown in the graphic is using RIP as the routing protocol. Which of the following are true regarding the network discovery process that will occur for this network? (Choose three.)The Palm Beach router will show networks 192.168.7.0 and 192.168.8.0 as directly connected networks.All of the routers will have direct knowledge of the exact topology of the entire network.The Key West router will forward routing table information to the Miami and Palm Beach routers.The Miami router will learn about network 192.168.1.0 from the Key West router.If network 192.168.4.0 becomes unavailable, the Key West router will notify the other routers of this fact in the next update.38. Which of the following are characteristics of the Open Shortest Path First (OSPF) routing protocol? (Choose two.) functions as a link-state routing protocoldiscards packets when the hop count is greater than 15calculates the shortest path to a destination using the Diffused Update Algorithm (DUAL)created as a proprietary routing protocolfloods updates as topology changes occurbroadcasts routing updates every 90 seconds or as triggered by topology changes39. The following line was displayed in the output of the show ip route command.R 192.168.3.0/24 [120/3] via 192.168.2.2, 00:00:30, Serial0/0What is the value of the routing metric?312203012040.Refer to the output from the show ip route command. What can be concluded from the output of this router command?A preferred route to the destination has not been set.There are two equal cost paths to network 1.0.0.0.Both interfaces are being used equally to route traffic.A variance must be set to load-balance across multiple paths.41. Which of the following are true statements about creating and applying access lists? (Choose three.)Access list entries should filter in the order from general to specific.One access list per port per protocol per direction is permitted.Standard ACLs should be applied closest to the source while extended ACLs should be applied closest to the destination. There is an implicit deny at the end of all access lists.Statements are processed sequentially from top to bottom until a match is found.The inbound keyword refers to traffic entering the network from the router interface where the ACL is applied.42. Which of the following are true regarding the setup configuration mode? (Choose three.)To abort the setup mode, use the CTRL+SHIFT+6 keys.To abort the setup mode, use the CTRL+C keys.Setup mode allows a complete configuration of the router.To enter setup mode, use the privileged mode setup command.A router that does not find a valid IOS during the boot process will start the system configuration dialog.A router that does not find a valid configuration file during the boot process will start the system configuration dialog.43. Which of the following are necessary for basic network communication to occur between hosts that will run such applications as Telnet, web browsers, and e-mail? (Choose three.)TCP/IP must be installed and properly configured on each device.。
CCNA期末测试多选题
CCNA期末测试多选题多选题：1、对于这样一个地址,192.168.19.255/20,下列说法正确的是: （）(A) 这是一个广播地址(B) 这是一个网络地址(C) 这是一个私有地址(D) 地址在192.168.19.0网段上(E) 地址在192.168.16.0网段上(F) 这是一个公有地址答案：CE2、下面有关NAT叙述正确的是（）(A) NAT是英文“地址转换”的缩写，又称地址翻译(B) NAT用来实现私有地址与公用网络地址之间的转换(C) 当内部网络的主机访问外部网络的时候，一定不需要NAT(D) 地址转换的提出为解决IP地址紧张的问题提供了一个有效途径答案：ABD3、关于VLAN下面说法正确的是（）(A) 隔离广播域(B) 相互间通信要通过路由器(C) 可以限制网上的计算机互相访问的权限(D) 只能在同一个物理网络上的主机进行逻辑分组答案:ABC4、下面对路由器的描述正确的是（交换机指二层交换机）（）(A) 相对于交换机和网桥来说，路由器具有更加复杂的功能(B) 相对于交换机和网桥来说，路由器具有更低的延迟(C) 相对于交换机和网桥来说，路由器可以提供更大的带宽和数据转发功能(D) 路由器可以实现不同子网之间的通信，交换机和网桥不能(E) 路由器可以实现虚拟局域网之间的通信，交换机和网桥不能答案:ADE5、关于IP报文头的TTL字段，以下说法正确的有（）（多选）(A) TTL的最大可能值是65535(B) 在正常情况下，路由器不应该从接口收到TTL=0的报文(C) TTL主要是为了防止IP报文在网络中的循环转发，浪费网络带宽(D) IP报文每经过一个网络设备，包括Hub、LAN SWITCH和路由器，TTL值都会被减去一定的数值答案:BC6、VLAN的划分方法有（多选）（）(A) 基于设备端口(B) 协议(C) MAC(D) 物理地址答案:ABCD7、路由项10.0.24.0/21由哪几条子网路由聚合而来（）(A) 10.0.0.25/16(B) 10.0.0.23/16(C) 10.0.0.26/16(D) 10.0.0.22/16答案:AC8、在OSPF中，以下（）是两台路由器成为邻居关系的必要条件。
CCNA第二学期考试答案
以下是针对您未获得满分的试题给出的反馈。
某些交互式试题可能不显示您的答案。
分项分数：1与固定配置的交换机相比，模块化交换机具有哪两个优点？（请选择两项。
）正确响应您的响应每台交换机的成本更低可扩展性更高转发率更低需要的电源插座数目更少带宽聚合可以使用多个端口固定配置交换机价格较低，但是它具有指定数量的端口且不能添加端口。
它们提供的高速端口通常比较少。
为了在包含固定配置交换机的网络上扩展交换，需要购买更多的交换机。
这增加了需要使用的电源插座数量。
模块化交换机只需要购买额外的线卡便可以扩展。
带宽聚合也更容易，因为机箱的背板可以为交换机端口线卡提供所需的带宽。
此试题参考以下领域的内容：Routing and Switching Essentials• 1.1.2 交换网络2思科无边界架构接入层的基本功能是什么？正确响应您的响应聚合第 2 层广播域聚合第 3 层路由边界为用户提供访问权提供高可用性思科无边界架构接入层的功能是为用户提供网络访问。
第 2 层广播域聚合、第 3 层路由边界聚合和高可用性是分布层的功能。
也有说答案是聚合第 3 层路由边界此试题参考以下领域的内容：Routing and Switching Essentials• 1.1.1 融合网络3思科无边界架构分布层的基本功能是什么？正确响应您的响应充当主干聚合所有园区块聚合第 3 层路由边界为用户提供访问权思科无边界架构的分布层的一项基本功能是在不同的VLAN 之间路由。
充当主干和聚合园区块是核心层的功能。
为用户提供访问是接入层的功能。
此试题参考以下领域的内容：Routing and Switching Essentials• 1.1.1 融合网络4若将大端口密度、容错和低价作为重要指标，应使用哪个交换机外形因素？正确响应您的响应固定配置交换机模块化交换机可配备机架的1U 交换机可堆叠式交换机堆叠式交换机可以使用特殊电缆实现互联，从而在交换机之间提供高带宽的吞吐量，并像单个大型交换机一样运行。
CCNA第二学期
CCNA 2 - Module 1If a router cannot find a valid configuration file during the startup sequence, what will occur?The router will prompt the user for a response to enter setup mode.Refer to the exhibit. The network administrator has configured the router with the interface IP addresses shown for the directly connected networks. Pings from the router to hosts on the connected networks or pings between router interfaces are not working. What is the most likely problem?The interfaces must be enabled with the no shutdown command.Refer to the exhibit. What can be concluded from the routing table output in the exhibit? (Choose two.) The FastEthernet0/0 and Serial0/0/0 interfaces of this router were configured with an IP address and the no shutdown command.An IP packet received by this router with a destination address of 198.18.9.1 will be forwarded out of the Serial0/0/0 interface.Refer to the exhibit. The frame shown in the exhibit was received by the router. The router interfaces are operational. How will the router process this frame? (Choose two.)The router will change the frame type to one supported by the WAN link before forwarding the frame.The frame was received on the Fa0/0 interface of the router and will be s witched to the S0/0/0 interface.Passwords can be used to restrict access to all or parts of the Cisco IOS. Select the modes and interfaces that can be protected with passwords. (Choose three.)VTY interfaceconsole interfaceprivileged EX EC modeWhich two statements correctly describe the components of a router? (Choose two.)ROM contains diagnostics executed on hardware modules.Flash memory does not lose its contents during a reboot.Refer to the exhibit. After host 2 is connected to the switch on the LAN, host 2 is unable to communicate with host 1. What is the cause of this problem?The subnet mask of host 2 is incorrect.Host 1 and host 2 are on different networks.The switch needs an IP address that is not configured.The router LA N interface and host 1 are on different networks.The IP address of host 1 is on a different network than is the LAN interface of the router.Which are functions of a router? (Choose three.)packet s witchingsegmentation of broadcast domainsselection of best path based on logical addressingRefer to the exhibit. A ll routers have a route in its routing table to each network that is shown in the exhibit. Default routes have not been issued on these routers. What can be concluded about how packets are forwarded in this network? (Choose two.)If RouterA receives a packet that is destined for 192.168.3.146, it will be forwarded out interface S0/0/1.If RouterB receives a packet that is destined for 10.5.27.15, it will be forwarded out interface S0/0/1.The serial connection shown in the graphic needs to be configured. Which configuration commands must be made on the Sydney router to establish connectivity with the Melbourne site? (Choose three.) Sydney(config-if)# ip address 201.100.53.2 255.255.255.0Sydney(config-if)# no shutdownSydney(config-if)# clock rate 56000Refer to the exhibit. What can be concluded from the output of the running-configuration of a router? The commands that are dis played determine the current operation of the router.Refer to the exhibit. Host A pings host B. When R4 accepts the ping into the Ethernet interface, what two pieces of header information are included? (Choose two.)destination IP address: 192.168.10.134destination MAC address: 9999.DADC.1234What is the outcome of entering these commands?R1(config)# line vty 0 4R1(config-line)# password check123R1(config-line)# loginsets the password to be used for connecting to this router via T elnetWhich of the following is the correct flow of routines for a router startup?load bootstrap, load IOS, apply configurationWhat three processes does a router execute when it receives a packet from one network that is destinedfor another network? (Choose three.)decapsulates the Layer 3 packet by stripping off the Layer 2 frame headeruses the destination IP Address in the IP header to look up the next-hop address in the routing tableencapsulates the Layer 3 packet into the new Layer 2 frame and forwards it out the exit interfaceThe network administrator needs to connect two routers directly via their FastEthernet ports. What cable should the network administrator use?cross-overWhich two statements describe characteristics of load balancing? (Choose two.)Load balancing allows a router to forward packets over multiple paths to the same destination network.Unequal cost load balancing is supported by EIGRP.What information about the router and its startup process can be gathered from the output of the show version command? (Choose three.)the last restart methodthe configuration register settingsthe location from where the IOS loadedWhich interfaces in the exhibit could be used for a leased line WAN connection? (Choose two.)14From what location can a router load the Cisco IOS during the boot process? (Choose two.)TFTP serverFlash memoryA network administrator has just entered new configurations into Router1. Which command should be executed to save configuration changes to NVRAM?Router1# copy running-config startup-configWhat is the default sequence for loading the configuration file?NVRAM, TFTP, CONSOLEWhat header address information does a router change in the information it receives from an attached Ethernet interface before information is transmitted out another interface?the Layer 2 source and destination addressCCNA 2 - Module 2Which of the following are displayed by the Router# show cdp neighbors command? (Choose three.)platformholdtimelocal interfaceWhy is it advisable to enter a next-hop IP address when creating a static route whose exit interface is an Ethernet network?In a multi-access network, the router cannot determine the next-hop MAC address for the Ethernet frame without a next-hop address.The output of the Router# show interfaces serial 0/1 command displays the following: Serial0/1 is up, line protocol is down.What is the most likely cause for the line protocol being down?No clock rate has been set.A static route that points to the next hop IP will have what administrative distance and metric in the routing table?administrative distance of 1 and metric of 0Refer to the exhibit. What two commands will change the next-hop address for the 10.0.0.0/8 network from 172.16.40.2 to 192.168.1.2? (Choose two.)A(config)# no ip route 10.0.0.0 255.0.0.0 172.16.40.2A(config)# ip route 10.0.0.0 255.0.0.0 192.168.1.2Refer to the exhibit. A company network engineer is assigned to establish connectivity between the two Ethernet networks so that hosts on the 10.1.1.0/24 subnet can contact hosts on the 10.1.2.0/24 subnet. The engineer has been told to use only static routing for these company routers. Which set of commands will establish connectivity between the two Ethernet networks?R1(config)# ip route 10.1.1.0 255.255.255.0 192.168.0.2R2(config)# ip route 10.1.2.0 255.255.255.0 192.168.0.1Refer to the exhibit. Which static route should be configured on Router1 so that hostA will be able to reach hostB on the 172.16.0.0 network?ip route 172.16.0.0 255.255.0.0 S0/0/0Which address can be used to summarize networks 172.16.0.0/24 thru 172.16.7.0/24?172.16.0.0/21Refer to the exhibit. What is the significance of the /8 in the route to the 10.0.0.0 network?It indicates the number of consecutive bits, from the left, in the destination IP address of a packet that must match 10.0.0.0 to use that route.What two devices are responsible for converting the data from the WAN service provider into a form acceptable by the router? (Choose two).a modema CSU/DSU deviceA network administrator enters the following command into Router1: ip route 192.168.0.0 255.255.255.0 S0/1/0. Router1 then receives a packet that is destined for192.168.0.22/24. After finding the recently configured static route in the routing table, what does Router1 do next to process the packet?encapsulates the packet into a frame for the WAN link and forwards the packet out the S0/1/0 interfaceWhich piece of information is available from examining the output of the command show ip interface brief?Interface IP addressWhich of the following is true regarding CDP and the graphic shown?By default, Router A will receive CDP advertisements from routers B and C.Which two statements describe functions or characteristics of CDP? (Choose two.)It starts up automatically and allows the device to detect directly connected neighbor devices that use CDP.It allows systems to learn about each other even if different network layer protocols are configured.Hosts on two separate subnets cannot communicate. The network administrator suspectsa missing route in one of the routing tables. Which three commands can be used to help troubleshoot Layer 3 connectivity issues? (Choose three.)pingtracerouteshow ip routeWhat happens to a static route entry in a routing table when the outgoing interface is not available?The route is removed from the table.The routers in the diagram use the subnet assignments shown. What is the most efficient route summary that can be configured on Router3 to advertise the internal networks to the cloud?192.1.1.0/25Refer to the exhibit. How will packets destined to the 172.16.0.0 network be forwarded? Router1 will perform recursive lookup and packet will exit S0/0.A router has one static route configured to each destination network. Which two scenarios would require an administrator to alter the static routes that are configured on that router? (Choose two.)The destination network no longer exists.A topology change occurs where the existing next-hop address or exit interface is not accessible.Refer to the exhibit. Given the output in the exhibit, how would a clock rate be determined for this link?The rate configured on the DCE determines the clock rate.Refer to the exhibit. Which set of commands will configure static routes that will allow the WinterPark and the Altamonte routers to deliver packets from each LAN and direct all other traffic to the Internet?WinterPark(config)# ip route 0.0.0.0 0.0.0.0 192.168.146.1Altamonte(config)# ip route 10.0.234.0 255.255.255.0 192.168.146.2Altamonte(config)# ip route 0.0.0.0 0.0.0.0 s0/1Refer to the exhibit. What two commands are required to provide connectivity betw een the 192.168.1.0 and 10.0.0.0 networks without requiring recursive lookup? (Choose two.)A(config)# ip route 10.0.0.0 255.0.0.0 s 0/1/0B(config)# ip route 192.168.1.0 255.255.255.0 s 0/0/0CCNA 2 - Module 3Which two statements correctly describe the concepts of administrative distance and metric? (Choose two.)Administrative distance refers to the trustworthiness of a particular route.Routes with the smallest metric to a destination indicate the best path.Refer to the exhibit. Which statement correctly describes how R1 will determine the best path to R2?R1 will install an EIGRP route using network B in its routing table because the administrative distance of EIGRP is lower than RIP.Which two statements are true regarding classless routing protoc ols? (Choose two.) sends subnet mask information in routing updatesallows for use of both 192.168.1.0/30 and 192.168.1.16/28 subnets in the same topologyWhich command would the network administrator issue to determine if load balancing is in effect on a router?show ip routeWhich statement is true regarding routing protocols?EIGRP uses DUAL to calculate the shortest path and can be configured to do unequal cost load balancing.Which two conditions would create a setting where the use of a distance-vector routing protocol would be efficient? (Choose two.)the network is using a hub and spoke topologythe network is using a flat designWhat is the purpose of a routing protocol?It allows a router to share information about known networks with other rou ters.Which of the following best describes the operation of distance vector routing protocols? They send their routing tables to directly connected neighbors.Which of the following is associated with link-state routing protocols?shortest-path first calculationsWhy is fast convergence desirable in networks that use dynamic routing protocols? Routers may make incorrect forwarding decisions until the network has converged.Which of the following conditions must be met in order for a network to have con verged The routers in the network are operating with consistent routing knowledge.Which two statements are true regarding metrics? (Choose two.)EIGRP uses bandwidth as a metric.OSPF uses cost based on bandwidth as a metric.Which two statements are true regarding the advantages of the use of static routes? (Choose two).increased securitythe administrator maintains control over routingThe following line of code is displayed in a routing table:R 209.165.201.0/24 [120/2] via 192.168.252.2, 00:00:16, S0/0/0What can be concluded from this output?The value, 120, is used to determine the best path when a router has more than one routing protocol configured for the same destination network.What will be the result of the following commands?ORL(config)# interface fastethernet 0/0ORL(config-if)# ip address 172.16.3.1 255.255.255.0ORL(config-if)# no shutdownA routing table entry is made to the 172.16.3.0 network with a code of "C".An engineer creates a static route by entering the Router(config)# ip route 10.0.0.0 255.255.255.0 192.168.1.2 command. What can be concluded about this route?The administrative distance of this route is 1.Refer to the exhibit. Router1 and Router2 are running EIGRP. All interfaces are operational and packets can be forwarded between all networks. What information will be found in the routing table for Router1?The administrative distance of the route to network 172.16.0.0 will be 90.The following line of code is present in the routing table:O 10.16.1.0/27 [110/129] via 192.168.1.5, 00:00:05, Serial0/0/1What does the number 129 indicate in this output?The cost for this link has a value of 129.A growing medium-sized manufacturing company recently began to have routing instability issues. The company uses static routes and has a mixture of over 30 Cisco and non-Cisco routers. The network administrator has decided to convert the network to dynamic routing. What characteristics of protocols should be considered in this selection process?OSPF can be used between the routers.Refer to the exhibit. If RIP is the routing protocol, what is the value of the metric from router A to network 192.168.5.0/24?3A router learns two paths with equal metrics to a destination network via the RIP routing protocol. How will the router handle packets to the destination network?The router will install both routes in the routing table and load balance between the two.CCNA 2 - Module 4Which event will cause a triggered update?a route is installed in the routing tableThree routers running a distance-vector routing protocol lost all power, including the battery backups. When the routers reload, what will happen?They will send updates that include only directly connected routes to their directly connected neighbors.What does the RIP holddown timer do?instructs routers to ignore updates, for a specified time or event, about possible inaccessible routesWhich two statements are true regarding the function of the RIPv1 routing updates? (Choose two).updates are broadcast at regular intervalsbroadcasts are sent to 255.255.255.255Which of the following statements are correct about RIP?will send out an update if there is a failure of a linkWhich two statements describe EIGRP? (Choose two.)EIGRP sends triggered updates whenever there is a change in topology that influences the routing information.EIGRP sends a partial routing table update, which includes just routes that have been changed.Which statement is true regarding cisco’s RIP_JITTER variable?It prevents the synchronization of routing updates by subtracting a random length of time ranging from 0% to 15% of the specified interval time from the next routing update interval.What actions will occur after RouterA loses connectivity to network 114.125.16.0? (Choose two.)RouterB will include network 123.92.76.0 and 136.125.85.0 in its update to RouterA.Router C will learn of the loss of connectivity to network 114.125.16.0 from RouterB.Which of the following methods does split horizon use to reduce incorrect routing information?Information learned from one source is not distributed back to that source.The graphic shows a network that is configured to use RIP routing protocol. Router2 detects that the link to Router1 has gone down. It then advertises the network for this link with a hop count metric of 16. Which routing loop prevention mechanism is in effect?route poisoningWhat is the purpose of the TTL field in the IP header?limits the time or hops that a packet can traverse through the network before it should be discardedWhich of the following can exist in a distance vector network that has not converged? (Choose three.)routing loopsinconsistent traffic forwardinginconsistent routing table entriesRefer to the exhibit. The routers in this network are running RIP. Router A has not received an update from Router B in over three minutes. How will Router A respond?The Invalid timer will mark the route as unusable if an update has not been received in 180 seconds.A network administrator is evaluating RIP versus EIGRP for a new network. The network will be sensitive to congestion and must respond quickly to topology changes. What are two good reasons to choose EIGRP instead of RIP in this case? (Choose two.)EIGRP only updates affected neighbors.EIGRP updates are partial.Refer to the exhibit. What path will packets from the 192.168.1.0/24 network travel to reach the 10.0.0.0/8 network if RIP is the active routing protocol?The path will be router A -> router D -> router E.Which three routing protocols are distance vector routing proto cols? (Choose three).RIPv1EIGRPRIPv2What is a routing loop?a condition where a packet is constantly transmitted within a series of routers without ever reaching its intended destinationWhich two conditions are most likely to cause a routing loop? (Choose two.)inconsistent routing tablesincorrectly configured static routesWhat metric does the RIP routing protocol consider to be infinity?16What does a router running RIP do first with a new route that is received from an advertisement?adjusts the metric for the new route to show the added distance for the routeRefer to the exhibit. If all routers are using RIP, how many rounds of updates will occur before all routers know all networks?3CCNA 2 - Module 5Refer to the exhibit. The network that is shown is running RIPv1. The 192.168.10.0/24 network was recently added and will only contain end users. What command or set of commands should be entered on Router1 to prevent RIPv1 updates from being sent to the end user devices on the new network while still allowing this new network to be advertised to other routers?Router1(config-router)# passive-interface fastethernet 0/0The following line was displayed in the output of the show ip route command.R 192.168.3.0/24 [120/3] via 192.168.2.2, 00:00:30, Serial0/0What is the value of the routing metric?3Which of the following is considered a limitation of RIP v1?RIP v1 does not send subnet mask information in its updates.Refer to the exhibit. The Ethernet interface on Router2 goes down and the administrator notices that the route is still in the Router1 routing table. How much longer will Router1 keep the down network in its routing table before marking it as possibly down?155 secondsRefer to the exhibit. Router1 is running RIPv1. What command was entered into Router1 to configure the gateway of last resort?ip route 0.0.0.0 0.0.0.0 S0/0/1What are three characteristics of the RIPv1 routing protocol? (Choose three.)uses hop count as a metricconsiders a metric of 16 as infinitycalculates metrics using the Bellman Ford algorithmWhich of the following would be the correct command sequence to enable RIP on Router B for all connected networks?RouterB(config)# router ripRouterB(config-router)# network 198.16.4.0RouterB(config-router)# network 210.36.7.0RouterB(config-router)# network 220.17.29.0What is the default update period in seconds for the RIP routing protocol?30Refer to the exhibit. What can be concluded from the routing table output of router B? The default-information originate command has been entered on A.Refer to the exhibit. A network consists of multiple routers. What can be verified when the show ip protocols command is issued on one of the routers in the network? routing protocol configuration in use for IP on this routerRefer to the exhibit. All routers are configured with valid interface addresses in the indicated networks and are running RIPv1. The network is converged. Which routes are present in the routing tables?All routers have all /30 routes. Routers A and E also have some of the /24 routes in their routing table.Which two statements are true regarding the characteristics of RIPv1? (Choose two). It is a distance vector routing protocol.The data portion of a RIP message is encapsulated into a UDP segment.Which command or set of commands will stop the RIP routing process?RouterB(config)# no router ripRefer to the exhibit. All routers in the exhibit are running RIP v1. The network administrator issues the show ip route command on router A. What routes would ap pear in the routing table output if the network is converged? (Choose two).R 192.168.2.0/24 [120/1]R 10.10.1.0/24 [120/2]Which command will display RIP activity as it occurs on a router?debug ip ripRefer to the output from the show ip route command. What can be concluded from the output of this router command?There are two equal cost paths to network 1.0.0.0.Refer to the exhibit. Router1 and Router2 are running the RIPv1 protocol. The network administrator configures the command network 10.1.0.0 on Router1. What network will Router1 advertise to Router2?10.0.0.0/8Refer to the exhibit. Pings between the serial interfaces of the routers are successful. Hosts on each LAN can ping the Fa0/0 interface of the router to which they are directlyconnected through the switch. However, pings between hosts on the 10.1.1.0/24 and 10.1.2.0/24 networks are unsuccessful. What is a likely cause of this problem?RIP is configured incorrectly on R1.What will happen if an interface IP address is entered for the address portion of the network command in a RIPv1 configuration instead of a network address?All interfaces in the same classful network as the configured address will be included in the RIPv1 routing process.Refer to the exhibit. All routers that are shown are running the RIP routing protocol. All unknown IP traffic must be forwarded to the ISP. What router or set of routers are recommended to have both a default route and the default-information originate command issued to implement this forwarding policy?only the gateway routerCCNA 2 - Module 6What two advantages does CIDR provide to a network? (Choose two.)reduced routing table sizereduced routing update trafficRefer to the exhibit. The network administrator wants to create a subnet for the po int-to-point connection between the two routers. Which subnetwork mask would provide enough addresses for the point-to-point link with the least number of wasted addresses?255.255.255.252Refer to the exhibit. A network engineer is summarizing the two groups of routes on router R1 shown in the exhibit. Which summarization will work for all the subnets?192.168.0.0/21Which of the following are contained in the routing updates of classless routing protocols? (Choose two.)32-bit addresssubnet maskWhich of the following problems does VLSM help to alleviate?the shortage of IP addressesWhat does VLSM allow a network administrator to do?utilize multiple subnet masks in the same IP address spaceRefer to the exhibit. What subnet mask will be applied if Router A sends a RIPv1 update for the network 172.16.1.0 to Router B?24Refer to the exhibit. The network administrator wants to minimize the number of entries in Router1’s routing table. What should the administrator implement on the network?CIDRA router has a summary route to network 192.168.32.0/20 installed in its routing table. What range of networks are summarized by this route?192.168.32.0 – 192.168.47.0/24A network administrator is tasked with dividing up a class C network among the QA, Sales, and Administration departments. The QA department is made up of 10 people, the Sales is made up of 28 people, and the Administration has 6. Which two subnets masks adequately address the QA and Sales departments? (Choose two.)255.255.255.224 for Sales255.255.255.240 for QAIn the network shown in the graphic, three bits were borrowed from the host portion of a Class C address. How many valid host addresses will be unused on the three point-to-point links combined if VLSM is not used?84A Class C address has been assigned for use in the network shown in the graphic. Using VLSM, which bit mask should be used to provide for the number of host addresses required on Router A, while wasting the fewest addresses?/27An additional subnet is required for a new Ethernet link between Router1 and Router2 as shown in the diagram. Which of the following subnet addresses can be configured in this network to provide a maximum of 14 useable addresses for this link while wasting the fewest addresses?192.1.1.224/28Which three interior routing protocols support VLSM? (Choose three.)OSPFRIP v2EIGRPRefer to the exhibit. The number of required host addresses for each subnet in a network is listed in the exhibit. This number includes the host address requirements for all router ports and hosts on that subnet. After all device and router port address assignments are determined, what will be the total number of unused host addresses available?29Refer to the exhibit. In the network that is shown, the router interfaces are assigned the first address ineach subnet. Which IP address would be usable for a host on one of the LANs in this network?192.168.2.130/25Refer to the exhibit. Which address is a broadcast address for one of the subnets that are shown in the exhibit?192.168.4.15/29Refer to the exhibit. A network administrator needs to create two subnetworks from 10.0.0.0/8 for a router running RIPv2. The Admin subnet requires 120 hosts and the Sales subnet requires 58 hosts. The network administrator assigned 10.0.1.128/25 to the Admin subnet. The Sales subnet i s given 10.0.1.192/26. What will be the result of this addressing scheme?Because RIPv2 does not support VLSM, the subnet masks will not be allowed.The subnets overlap and will be rejected by the router.Refer to the exhibit. A network technician enters the static route in R1 needed to reach network 10.1.1.0/24. A ping from the S0/0/0 interface on R1 to host B fails. The technician begins testing the network and has the following results:1. pings from R1 to the S0/0/0 interface on R2....successful2. pings from R1 to the Fa0/0 interface on R2....successful3. pings from host B to hosts on the 10.1.1.0/24 network....successful4. pings from host B to the Fa0/0 interface on R2....successful5. pings from R2 to host B....successful.The default gateway on host B is not correctly set.What is a supernet?a summarization of classful addressesCCNA 2 - Module 7Refer to the exhibit. If all routers are running RIP version 2, why is there no route for the 192.168.1.32/27 network?Rip version 2 will auto summarize routes by default.Refer to the exhibit. Which two statements are true? (Choose two.)Router1 will install a route to 192.168.0.0/20Router2 will not install a route to 192.168.16.0/20Refer to the exhibit. Which command on which router will allow Router1 to learn about the 192.168.0.0/20 network?Router2(config-router)# version 2What are two reasons to implement RIP version 2 rather than RIP version 1? (Choose two.)RIP version 2 supports VLS M.。
CCNA2期末测试题
1请参见图示。
对于发往192.168.2.0 的数据包，R2 会采取什么操作？它会丢弃数据包。
它会通过S0/0/0 接口转发数据包。
它会通过Fa0/0 接口转发数据包。
它会将数据包转发给R1。
2请参见图示。
R1 会使用哪一总结地址来向R2 通告其网络？3请参见图示。
尽管R2 已配置正确，但主机A 还是无法访问Internet。
可以在R1 上配置哪两条可让主机A 访问Internet 的静态路由？（选择两项。
）ip route .0 0.0.0.0 Fa0/0ip route .0 0.0.0.0 Fa0/1ip routeip routeip route 209.165.202.0 255.255.255.0 .14请参见图示。
网络管理员已按图示配置了R1，并且所有接口都运作正常。
但从R1 ping 172.16.1.1 时失败。
造成此问题的原因可能是什么？R1 上的串行接口配置有误。
默认路由配置有误。
必须在R1 上发出default-information originate命令。
必须在R1 上禁用自动总结。
5请参见图示。
所有接口都已编址，并且运行正常。
网络管理员在主机A 上运行了tracert命令。
得到这种输出的原因可能是什么？（选择两项。
）主机A 缺少网关或配置不正确。
主机B 缺少网关或配置不正确。
R1 的路由表中缺少192.168.1.0/24 的条目。
R2 的路由表中缺少192.168.1.0/24 的条目。
R1 的路由表中缺少192.168.2.0/24 的条目。
R2 的路由表中缺少192.168.2.0/24 的条目。
6请参见图示。
从主机A 到主机B 的ping 成功，但从主机A ping 在Internet 上正常运行的主机却失败了。
此问题的原因是什么？R1 的快速以太网接口被禁用。
其中一条默认路由配置有误。
未在这两台路由器上配置路由协议。
主机A 上尚未配置默认网关。
7 网络管理员使用RIP 路由协议在一个自治系统内实施路由。
CCNA 2 Final Exam Answers V3.1
1. What are two possible reasons a router would not load a valid IOS from flash? (Choose two.)The configuration register is set to 0×2142.The first boot system command executed in the startup configuration file is boot system rom.The configuration register is set to 0×2100.The boot field is set to the hexadecimal number 2.The startup configuration file is missing or corrupt.2. What are two recommended uses of login banners? (Choose two.)to display security warning messagesto welcome any user to the routerto warn people about misusing privileged EXEC modeto identify circuits and other devices connected to the routerto announce a scheduled system shutdown3.Router A and Router B have been correctly configured to use RIP as a dynamic routing protocol and all intefaces on Router A and Router B are reporting "interface is up, line protocol is up" status. RIP is then configured onRouter C using the following commands:RouterC(config)# router ripRouterC(config-router)# network 192.168.4.0RouterC(config-router)# network 172.16.0.0If no additional routing is configured on Router A, Router B, and Router C, what will be the result?Networks 192.168.12.0/24, 192.168.4.0/24, and 172.16.0.0/16 will be unreachable from Router A.Router A will have no knowledge of network 192.168.12.0/24, but will have routes to networks 192.168.4.0/24 and 172.16.0.0/16.All networks shown in the graphic will be reachable by Router A, Router B, and Router C.Networks 192.168.4.0/24 and 172.16.0.0/16 will be unreachable from Router A and Router B.4. What are the primary functions of a router? (Choose two.) determine the best path for packetsprevent collisions on the network LANregulate flow control between sender and receiverprovide domain name resolutionforward packets to the appropriate interface5. What are some reasons to change the configuration register setting? (Choose two.)to force the system to ignore the configuration file stored in NVRAM to monitor password changesto change the POST sequenceto force the router to boot the IOS from NVRAMto force the system into ROM monitor mode6. A network administrator issues the erase startup-config command on a configured router with the configuration register set to 0×2102 and observes the following output:Erasing the nvram filesystem will remove all files! Continue? [Confirm] [OK]Erase of nvram: completeIf the router unexpectedly loses power after this sequence, what will occur when power is restored?The router will enter ROM monitor mode upon completion of the power-on self test (POST).The router will load the last known valid configuration file.The router will enter Rx-boot mode.The router will prompt the user to enter setup mode or to continue without entering setup mode.7. Why are routed protocols important to networking? (Choose two.) Routed protocols detect collisions and fragments.Routers use routed protocols to calculate the best path to a destination. Routed protocols transport data across the network.The fields and formats used within a packet are defined by routed protocols.Routed protocols are used to configure the metrics used by routing protocols.8. The main router of XYZ company has enough flash and RAM to store multiple IOS images. An administrator wants to upload a second IOS image from a TFTP server to the flash of the router. Which method will accomplish this task?Paste the IOS filename to the command line of the router while in global configuration mode. Press enter. Then issue the copy tftp flash command.Use the setup utility to load the new image to flash.Copy the IOS image file from a TFTP server using the command copy filenameip address flash .Copy the IOS image file from a TFTP server using the command copy tftp flash. When prompted, provide the IP address or name of the TFTP server and the IOS image filename.9.A network administrator has a console connection to the Fremantle router. Pings to Melville are successful, but pings to Cottesloe and Nedlands fail. What could be a first step in troubleshooting the problem?Use an extended ping from Fremantle to each router in the network.Use the show interfaces command from a Telnet session on Melville to check the connection to Cottesloe.Use the traceroute command to discover exactly which link in the network is down.Use the show cdp neighbors detail command from Fremantle to gather information about all Cisco routers in the network.10.Refer to the exhibit. The new security policy for the company allows all IP traffic from the Engineering LAN to the Internet while only web traffic from the Marketing LAN is allowed to the Internet. Which ACL can be applied in the outbound direction of Serial 0/1 on the Marketing router to implement the new security policy?access-list 197 permit ip 192.0.2.0 0.0.0.255 anyaccess-list 197 permit ip 198.18.112.0 0.0.0.255 any eq wwwaccess-list 165 permit ip 192.0.2.0 0.0.0.255 anyaccess-list 165 permit tcp 198.18.112.0 0.0.0.255 any eq wwwaccess-list 165 permit ip any anyaccess-list 137 permit ip 192.0.2.0 0.0.0.255 anyaccess-list 137 permit tcp 198.18.112.0 0.0.0.255 any eq wwwaccess-list 89 permit 192.0.2.0 0.0.0.255 anyaccess-list 89 permit tcp 198.18.112.0 0.0.0.255 any eq www11.Hosts from the Limerick LAN are not allowed access to the Shannon LAN but should be able to access the Internet. Which set of commands will create a standard ACL that will apply to traffic on the Shannon router interface Fa0/0 implementing this security?access-list 42 deny 172.19.123.0 0.0.0.255 192.0.2.0 0.0.0.255 access-list 42 permit anyaccess-list 56 deny 172.19.123.0 0.0.0.255access-list 56 permit anyaccess-list 61 deny 172.19.123.0 0.0.0.0access-list 61 permit anyaccess-list 87 deny ip any 192.0.2.0 0.0.0.255access-list 87 permit ip any12. Which of the following commands will correctly configure an extended ACL? (Choose two).Router(config)# access-list 18 permit tcp host 192.168.73.3 eq 25Router(config)# access-list 102 permit tcp 10.43.0.0 0.0.255.255 any eq 80Router(config)# access-list 187 permit tcp host 192.168.42.34 172.29.0.0 0.0.255.255 eq 23Router(config)# access-list 99 permit host 10.217.32.3Router(config)# access-list 128 permit tcp host 192.168.100.31 eq 2313. What are the results of setting the boot field bits in the configuration register to "0000"? (Choose two.)The startup-config file will be ignored at bootup.The router will load the IOS from Flash.The router will enter ROM monitor mode upon reload.The router will enter boot ROM mode and have limited capabilities. The administrator can enter the b command to manually boot the IOS.14.Refer to the exhibit. Router D interface S0 on has gone down. What is the maximum time that will elapse before Router A learns that network 168.58.14.0 is down?5 seconds13 seconds17 seconds25 seconds30 seconds77 seconds15. During initial router bootup the following line appears: "NVRAM invalid, possibly due to write erase."What are two possible reasons for this result? (Choose two.)The startup-config file was not saved to RAM before reboot.The IOS has been erased.The router has not been configured.The startup-config file cannot be located.The router will not enter initial configuration dialog.16.The Suffolk router is directly connected to the networks shown in the graphic and has a default route that points to the Richmond router. All interfaces are active and properly addressed. However, when the workstation on network 172.29.5.0/24 sends a packet to destination address 172.29.198.5, it is discarded by the Suffolk router. What can be a reason for this result?The ip classless command is not enabled on the Richmond router.The route was ignored if the Richmond router did not include the 172.29.198.0/24 network in its routing updates.The Richmond router is in a different autonomous system than the Suffolk router.The ip subnet-zero command was not configured on the Suffolk router.The ip classless command is not enabled on the Suffolk router.17. access-list 199 deny tcp 178.15.0.0 0.0.255.255 any eq 23 access-list 199 permit ip any anyAssuming this ACL is correctly applied to a router interface, which statements describe traffic on the network? (Choose two.)All FTP traffic from network 178.15.0.0 will be permitted.All Telnet traffic destined for network 178.15.0.0 will be denied.Telnet and FTP will be permitted from all hosts on network 178.15.0.0 to any destination.Telnet will not be permitted from any hosts on network 178.15.0.0 to any destination.Telnet will not be permitted to any host on network 178.15.0.0 from any destination.18.What facts can be determined from the highlighted text shown in the exhibit? (Choose two.)A weak encryption was applied to all unencrypted passwords.The enable password is now more secure than the enable secret password.An MD5 hashing algorithm was used on all encrypted passwords.Any configured user EXEC mode or Telnet passwords will be encrypted in this configuration.The service password-encryption command was used to encrypt all passwords on the router including enable secret.19. What are three features of CDP? (Choose three.)provides information on directly connected devices that have CDP enabled tests Layer 2 connectivityenabled by default on each interfaceprovides a layer of securityused for debugging Layer 4 connectivity issues20. What information can be learned during the initial router bootup? (Choose two.)the configuration register valuethe number and types of interfaces installedthe router model and the amount of memory that is availablethe amount of memory required to load the IOS and configurationthe number of interfaces with connected cables21.What can be concluded from the output shown in the exhibit? (Choose three.)This is a standard IP access list.This is an extended IP access list.The keyword host is implied in the command line access-list 99 deny 10.213.177.76.The wildcard mask must be configured for this access list to function properly.Host 10.213.177.100 will be allowed access to the Serial0/1 interface.22. Which statements are true regarding setup mode? (Choose three.)Press Ctrl-z to terminate setup mode.Enter a question mark (?) for help at any point.Press Spacebar to accept the default settings.Use setup mode to enter complex protocol features.Press Enter to accept the default settings.Press Ctrl-c to abort configuration dialog.23.Refer to the graphic. Which series of commands will create static routes that will allow Router A and Router B to deliver packets destined for LAN A and LAN B, and direct all other traffic to the Internet?RouterA(config)# ip route 10.90.3.0 255.255.255.0 192.168.3.2RouterB(config)# ip route 192.168.2.0 255.255.255.0 192.168.3.1 RouterB(config)# ip route 0.0.0.0 0.0.0.0 s0/0RouterA(config)# ip route 10.90.3.0 255.255.255.0 192.168.3.2RouterA(config)# ip route 0.0.0.0 0.0.0.0 192.168.3.2RouterB(config)# ip route 192.168.2.0 255.255.255.0 192.168.3.1RouterA(config)# ip route 0.0.0.0 0.0.0.0 192.168.3.2RouterB(config)# ip route 192.168.2.0 255.255.255.0 192.168.3.1 RouterB(config)# ip route 172.20.20.4 255.255.255.252 s0/0RouterA(config)# ip route 0.0.0.0 0.0.0.0 192.168.3.2RouterB(config)# ip route 192.168.2.0 255.255.255.0 192.168.3.1 RouterB(config)# ip route 0.0.0.0 0.0.0.0 s0/024.Which devices can be used to convert the data from a WAN router at the customer site into a form acceptable for use by the WAN service provider? (Choose three.)Ethernet switchDTEmodemhubDCE deviceCSU/DSU25.What will occur when the following ACL is applied inbound to both FastEthernet interfaces of Router A in the graphic?access-list 125 permit tcp 192.168.2.0 0.0.0.255 10.90.3.0 0.0.0.255 eq 23access-list 125 permit tcp 10.90.3.0 0.0.0.255 192.168.2.0 0.0.0.255 eq 23access-list 125 permit tcp 192.168.2.0 0.0.0.255 any eq wwwWorkstations A and B will be able to Telnet to each other. WorkstationA will be allowed to access Web servers on the Internet, while WorkstationB will be denied Internet Web access.Workstations A and B will be able to Telnet to each other. All other traffic will be denied.The ACL will have no effect because it should be applied in the outbound direction on the FastEthernet interfaces.The ACL will deny all traffic because of the implied deny ip any any statement at the end of the ACL.26. Based on this partial output of the show ip route command, which routing protocol is configured on the router?R 172.16.3.0/24 [120/3] via 172.16.2.2, 00:00:27, Serial0/0RIPEIGRPOSPFIGPBGP27.Which of the following are correct statements verified by the router output shown in the graphic? (Choose two.)Layer 3 connectivity exists between BigCity and the devices in the Device ID column.Layer 2 connectivity exists between BigCity and the devices in the Device ID column.All devices shown in the Device ID column use the TCP/IP protocol suite.All devices shown in the Device ID column can be pinged from BigCity.All devices listed in the Device ID column are directly connected to BigCity.28. A network administrator must configure a FastEthernet interface with an IP address. The configuration must also identify the remote site to which the interface is connected. Which set of commands will meet these requirements?StPetersburg(config)# banner San Jose T1StPetersburg(config)# interface fa0/0StPetersburg(config-if)# ip address 172.26.155.5 255.255.255.252StPetersburg(config)# interface fa0/0StPetersburg(config-if)# ip address 172.26.155.5 netmask255.255.255.252StPetersburg(config-if)# description San Jose T1StPetersburg(config)# interface fa0/0StPetersburg(config-if)# ip address 172.26.155.5 255.255.255.252 StPetersburg(config-if)# banner remote site San Jose T1StPetersburg(config)# interface fa0/0StPetersburg(config-if)# ip address 172.26.155.5 255.255.255.252 StPetersburg(config-if)# description San Jose T129. What are the features of a serial interface on a router? (Choose two.) enabled by defaultassigned a unique MAC addressmust be configured as a DCE in lab and production environmentsmust be configured with the default clock rate of 56000may be administratively enabled by using the no shutdown commandmust be configured with a valid IP address and subnet mask in order to forward packets30. Assuming the following ACL is correctly applied to a router interface, what can be concluded about this set of commands? (Choose two.) Router(config)# access-list 165 deny tcp 192.28.115.0 0.0.0.255 172.20.0.0 0.0.255.255 eq 23Router(config)# access-list 165 permit ip any anyThis is a standard IP access list that denies network 192.28.115.0 Telnet access to the 172.20.0.0 network.All Telnet traffic destined for 172.20.0.0 from any network will be denied access.Network 192.28.115.0 is denied Telnet access to the 172.20.0.0 network. Network 172.20.0.0 is denied Telnet access to the 192.28.115.0 network.All FTP and HTTP traffic destined for 172.20.0.0 will be permitted access.31. Which two steps describe how to create a functional physical connection between a router console and a terminal? (Choose two.)Use a crossover cable to connect the terminal serial port to the router console port.Use a rollover cable to connect the terminal NIC to the router console port.Use an RJ-45 to DB-9 adapter on the terminal serial port to connect to the cable going to the router console.Use a transceiver to connect a straight-through cable to the router console port.Use a straight-through cable to connect the router console port to the terminal NIC.Use a rollover cable to connect from a terminal serial port to the router console port.32. What critical information about the status of the router can be found in the outputs of both the show interfaces and show protocols commands? (Choose two.)the Layer 3 address of each configured interfacethe routing protocol configured to forward updates out of each interface the operational status of each interfacetraffic statistics for each interfacewhether the interface is configured as a DTE or DCE33.The following access list has been created to prevent traffic from the 192.0.2.63 host on the Sales LAN from accessing servers and hosts on the Payroll LAN.access-list 26 deny host 192.0.2.63access-list 26 permit anyRefer to the exhibit. Which group of commands will properly place the access list so that only the host on the Sales LAN is denied access to the 172.29.7.0 network but all other traffic is permitted?Payroll(config)# interface fa0/0Payroll(config-if)# ip access-group 26 outPayroll(config)# interface fa0/1Payroll(config-if)# ip access-group 26 outSales(config)# interface fa0/1Sales(config-if)# ip access-group 26 inSales(config)# interface fa0/0Sales(config-if)# ip access-group 26 out34.Refer to the exhibit. Assuming default metrics are used and the networkis fully converged, which path will RIP use to send a packet from Router A to Router F?A, D, E, FA, B, D, E, FA, C, D, E, G, FA, B, D, E, G, F35.Refer to the graphic. Communication is needed between the LAN connected to the fa0/0 interface of the Kansas router and the fa0/0 interface of the Maine router. All hosts on those LANs also need connectivity to the Internet. Which commands will allow this communication? (Choose three).Kansas(config)# ip route 192.168.6.0 255.255.255.0 172.18.64.2Kansas(config)# ip route 192.168.6.0 255.255.255.0 s0/1Kansas(config)# ip route 0.0.0.0 0.0.0.0 s0/1Maine(config)# ip route 192.168.6.0 255.255.255.0 172.18.64.1Maine(config)# ip route 0.0.0.0 0.0.0.0 s0/1Maine(config)# ip route 172.16.32.0 255.255.255.0 172.18.64.236. Why are interface descriptions used in router configurations? (Choose three).to enable support personnel to easily identify networks and customers that may be affected by a possible interface issueto provide comments on the interface without affecting the router functionalityto display access warning messages before users enter the interface configuration modeto eliminate the need to use IP addresses when using the ping and telnet commandsto identify the purpose and location of the interface37.A network administrator has enabled RIP on routersB andC in the network diagram. Which of the following commands will prevent RIP updates from being sent to Router A?A(config)# router ripA(config-router)# passive-interface S0/0B(config)# router ripB(config-router)# network 192.168.25.48B(config-router)# network 192.168.25.64A(config)# router ripA(config-router)# no network 192.168.25.32B(config)# router ripB(config-router)# passive-interface S0/0A(config)# no router rip38. What could a Cisco support technician learn from the IOS filename c2600-d-mz.121-3? (Choose three.)the format of the filethe RAM memory requirements of the filethe version number of the filethe size of the filethe device platform of the file39.While planning an IOS upgrade, the administrator issues the show version command. Based on the output in the graphic, what is the current IOS boot location?RAMNVRAMFlashROM40. A new technician must add boot system commands to one of the department routers. Which available commands will the router return as output when the command shown below is entered? (Choose two.)Router(config)# boot system ?RAMNVRAMIOSIP AddressTFTPFLASH41. From the running-config, the following configuration entries are displayed:Router(config)# line vty 0 2Router(config-line)# password g8k33prRouter(config-line)# loginWhat can be interpreted from the exhibited configuration? (Choose two.)Three Telnet lines are available for remote access.Two Telnet lines are available for remote access.Future configuration of the remaining Telnet lines will require the password to be set to g8k33pr.To login to the remote device, g8k33pr will be used as the Telnet and secret password.Remote access to this local router will require a Telnet password of g8k33pr.42. Which router component stores the information that is displayed by the show running-config command?flashNVRAMRAMROM43. What are two characteristics of the support for Telnet within Cisco IOS software? (Choose two.)Up to five separate Telnet lines are supported by default in standard edition IOS files.For security purposes, Telnet sessions are required to be established from the privileged mode.A router can host simultaneous Telnet sessions.Once established, a Telnet session can remain operational regardless of network status.Telnet tests wireless connectivity and does not require a physical connection between devices to gain remote access.44. Which router components and operations are correctly described? (Choose two.)RAM – stores the ARP cacheNVRAM – store the operating systemROM – stores the backup IOSPOST – verifies the validity of the running-configFlash – executes diagnostics at bootupDRAM – loads the bootstrap45.Given the output shown in the exhibit, in what order and location will the router search for the IOS if no boot system commands are found in the startup-config file?ROM, Flash, TFTP serverFlash, NVRAM, RAMROM, TFTP server, FlashRAM, Flash, NVRAMFlash, TFTP server, ROM46. What can a network administrator do to recover from a lost router password?perform a reload or resettelnet from another router and issue the show running-config command to view the passwordboot the router to ROM monitor mode and configure the router to ignore NVRAM when it initializesboot the router to bootROM mode and enter the b command to load the IOS manually47.Neither router in the exhibit has a host table or DNS available. The interfaces and passwords have been correctly configured. Which of the following commands will initiate a Telnet session? (Choose two.)Tottenham# telnet OxfordTottenham> telnet 198.18.139.1Oxford# connect 198.18.139.0Oxford> connect TottenhamOxford# telnet TottenhamOxford# 198.18.139.248. If a PC does not have network connectivity to a router, which router port can be used to establish communication?consoleEthernetserialVTY。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
C C N A第二学期期末考试E x a m集团文件发布号：（9816-UATWW-MWUB-WUNN-INNUL-DQQTY-路由器获知到的第一条路径仅使用路由器获知到的前两条路径路由器获知到的最后一条路径所有四条路径对于为防止路由环路而通过毒性反转实现的水平分割方法，哪两项叙述正确（选择两项所有 Cisco IOS 都会默认启用此方法。
会将一个表示无穷大度量的值分配给路由以将其毒化。
将毒化路由更新发回该更新的发送接口。
指示路由器将可能会影响路由的更改保持一段特定的时间。
限制数据包在被丢弃之前能够在网络中传输的跳数。
在两台路由器能够使用 OSPF 形成邻居邻接关系之前必须完成哪两项任务（选择两项。
路由器必须选举出指定路由器。
路由器必须在网络类型方面达成一致。
路由器必须使用相同的 dead 时间间隔。
路由器必须交换链路状态请求。
路由器必须交换数据库描述数据包。
下列路由器组件和操作的配对中，哪两项是正确的（选择两项。
）D RAM - 加载 bootstrapR AM - 存储操作系统闪存 - 启动时执行诊断N VRAM - 存储配置文件R OM - 存储备份配置文件P OST - 运行硬件模块诊断下列关于无类路由协议的陈述，哪两项是正确的（选择两项。
）无类路由协议可用于不连续子网。
无类路由协议可在路由更新中转发超网路由。
无类路由协议无法在路由表中实施有类路由。
无类路由协议仅使用跳数度量。
无类路由协议的路由更新中不包含子网掩码。
请参见图示。
在图示的其中一台设备上运行了show cdp neighbors命令。
根据此信推断出哪两项结论（选择两项。
）在路由器上运行了该命令。
A BCD 是一台非 CISCO 设备。
两台设备间存在第 3 层连通性。
A BCD 支持路由功能。
A BCD 连接到相邻设备的 Fa0/0 接口。
请参见图示。
网络连接有三台路由器：R1、R2 和 R3。
图中显示了所有三台路由器的从该输出可以得到什么结论R1 和 R3 通过 S0/0/0 接口相连。
R1 S0/0/0 接口的 IP 地址为 10.1.1.2。
R2 S0/0/1 接口的 IP 地址为 10.3.3.2。
R2 连接到 R3 的 S0/0/1 接口。
√D请参见图示。
要完成路由器 R1 与 WAN 之间的连接，可使用下列哪两种设备（选择C SU/DSU 设备调制解调器以太网交换机集线器网桥请参见图示。
根据如图所示的输出，下列哪两项陈述是正确的（选择两项。
）所有路由都处于稳定状态。
每条路由都有一个可行后继。
两台路由器之间的串行接口关闭。
E IGRP 的管理距离已设置为 50。
R1 上已运行了show ip eigrp topology命令。
一台使用 RIP 路由协议的路由器在路由表中存有到某个网络的路由条目。
后来，路由另一条到同一目的网络的路由条目的更新，且与前者比，该路由跳数较少。
对于此更器会采取什么操作路由器会将更新信息附加到路由表中。
路由器会将路由表中到该网络的路由条目标记为无效。
路由器会用新信息替换现有的路由表条目。
路由器会忽略新的更新。
请参见图示。
网络管理员将此命令添加到路由器 R1：。
添加此命令会产生什么结果此路由会在网络中自动传播。
建立一条静态路由。
请参见图示。
从突出显示的输出可以得到什么信息自动总结被禁用。
选B网络使用的是有类路由协议。
请参见图示。
网络管理员从 R3 上成功 ping 通了 R1。
接下来，管理员在 R3 上运show cdp neighbors命令。
图中显示了该命令的输出。
输出中缺少 R1 的两个原因是什么（选择两项。
）R1 和 R3 之间有连通性问题。
R1 的 Fa0/0 接口配置了不正确的 IP 地址。
在 R1 上运行了no cdp run命令。
对 R3 的 Fa0/1 接口运行了no cdp enable命令。
关闭了 R1 的电源。
数据会通过 R3-R2 传输。
数据会通过 R3-R1-R2 传输。
流量会在两条路径（R3-R2 和 R3-R1-R2）间进行负载均衡。
数据会通过 R3-R2 传输，而另一条通过 R3-R1-R2 的路径则会留作备用路径。
请参见图示。
网络管理员运行了show interface命令。
图中显示了该命令的输出。
接口工作，需要采取的第一步是什么用已知能够正常工作的电缆替换所用电缆。
对接口发出no shutdown命令。
将接口配置为环回接口。
为接口设置封装。
经由 A、B 和 C 传输。
经由 A、F、E、D 和 C 传输。
经由 A、G、H 和 C 传输。
流量会在所有路径上进行负载均衡。
网络管理员在所示网络图中的路由器 B 和 C 上启用了 RIP。
什么命令可防止向路由器RIP 更新A(config)# router ripA(config-router)# passive-interface S0/0B(config)# router ripB(config-router)#B(config-router)#A(config)# router ripA(config-router)#B(config)# router ripB(config-router)# passive-interface S0/0A(config)# no router rip请参见图示。
下列有关所示网络中快速以太网接口的陈述，哪一项是正确的帧离开 R1 的接口 Fa0/0，源 MAC 地址为 000C.。
10.1.1除非对 R1 的 Fa0/0 接口发出no shutdown 命令，否则 R1 和 R2 之间不会转发数据请参见图示。
R2 应使用哪个总结地址将其 LAN 网络通告给 R1请参见图示。
PC1 无法访问 Internet。
此问题的原因是什么两台路由器之间配置了错误的 IP 地址。
R outer2 上未配置静态路由。
出现了路由环路。
两台路由器上均未配置路由协议。
请参见图示。
所有路由器都配置为运行 RIPv1，并已完全收敛。
R3 会收到下列哪项由更新哪种路由协议默认使用带宽和延迟来计算路由的度量R IPv1R IPv2O SPFE IGRP关于数据包通过路由器传输时的封装和解封的叙述，下列哪三项是正确的（选择三项。
路由器修改 TTL 字段，将其值减 1。
路由器将源 IP 更改为送出接口的 IP。
路由器保持相同的源 IP 和目的 IP。
路由器将源物理地址更改为送出接口的物理地址。
路由器将目的 IP 更改为送出接口的 IP。
路由器会从所有接口将数据包转发出去，包括路由器接收数据包时使用的那个接口。
路由器配置了不同版本的 RIP。
R2 不会转发路由更新。
R1 的配置应包含no auto-summary命令。
已超出最大路径数。
请参见图示。
网络管理员从控制台端口访问路由器 R1，以配置一个新连接的接口。
接并进行必要的配置更改，管理员需要需要输入什么口令仅需输入 Cisco123 口令仅需输入 Cisco789 口令仅需输入 Cisco001 口令C isco001 和 Cisco789 口令C isco001 和 Cisco123 口令请参见图示。
尽管两台路由器都可以 ping 通其邻居的串行接口，但无法 ping 通其的以太网接口。
下列关于此网络的说法中哪两项正确（选择两项。
）两台路由器上的管理距离都设置为 50。
两台路由器上都未运行network 10.1.1.0 命令。
两台路由器上都启用了自动总结。
请参见图示。
网络管理员已使用以下命令配置了 OSPF。
0.0.0.31 area 0哪个路由器接口将参与 OSPFF astEthernet0/0F astEthernet0/1S erial0/0/0S erial0/0/1R outer1R outer2R outer3R outer4路由器启动时，如果没有boot system命令，则查找 Cisco IOS 的默认顺序是什么R OM、TFTP 服务器、闪存闪存、TFTP 服务器、ROM 选B闪存、NVRAM、TFTP 服务器R OM、TFTP 服务器、闪存网络管理员需要配置一台路由器，用于在不等价路径上负载均衡流量。
管理员应采用由协议E IGRPO SPFR IPv1R IPv20/1/1下列关于 OSPF Hello 数据包的陈述，哪两项是正确的（选择两项。
）用于动态发现邻居。
用于维护邻居关系。
用于确定完整的网络拓扑。
与计时器一起用来选举链路速度最快的指定路由器。
用于在相邻接口之间协商正确的参数。
请参见图示。
命令ip route 0.0.0已在路由器 R2 上生效。
此命令会产生哪两项结择两项。
）会在路由表中更新静态路由。
来自 Internet 的流量会转发给 R2。
该路由会被指定为到路由表中所有未定义的网络的默认路由。
所有广播都会通过 R2 的 S0/0/0 接口转发。
请参见图示。
网络管理员已在 R1 上运行了show ip protocol命令。
从所示的输出什么结论路由器正在使用 RIPv2。
路由器不会转发路由更新。
路由器会收到两个 RIP 版本的更新。
F astEthernet0/0 接口关闭。
请参见图示。
R1 LAN 中的主机无法访问 Internet。
下列哪项配置有误R1 Fa0/0 接口的 IP 地址R2 S0/0/1 接口的 IP 地址R1 S0/0/0 接口的 IP 地址R2 S0/0/1 接口的子网掩码请参见图示。
从 R1 能够 ping 通 10.1.1在 R1 处没有最后选用网关。
两台路由器之间的串行接口关闭。
R1 上未配置默认路由。
下列哪两项是路由器的功能（选择两项。
）连接多个 IP 网络。
通过使用第 2 层地址控制数据流。
确定发送数据包的最佳路径。
管理 VLAN 数据库。
扩大广播域。
请参见图示。
有多少条路由是子路由346请参见图示。
所有路由均已通告给所有路由器且均运行正常。
下列有关数据从路由器由器 B 传输的路径，哪一项叙述正确如果采用 EIGRP 的默认配置，数据会在两条路径（A, D, B 和 A, C, B）之间平均分如果采用 RIPv1 的默认配置，数据会在所有路径上进行负载均衡。
如果同时使用 EIGRP 和 OSPF 的默认配置，数据会通过由 OSPF 协议获知的路径发送如果采用 RIPv2 的默认配置，数据会在两条路径（A, D, B 和 A, C, D）之间平均分请参见图示。
突出显示的值 120 表示什么意思路由协议计算出的度量。
D UAL 算法使用该值来确定该链路的带宽。
路由协议的管理距离。
收到下一个更新前的抑制时间，单位为秒。
请参见图示。
当数据包发往哪两个网络时需要路由器执行递归查找（选择两项。
）10.0.0.0/8请参见图示。
主机 A 无法访问 Internet，经查明这是由编址问题造成的。