中兴OLT全局配置流程
C300 EPON 中兴开局初学者配置手册最新
1、一个新的OLT了首先第一步就是配置单板，卡槽，机框等信息ZXAN(config)#add-rack rackno 1 racktype IEC19ZXAN(config)#add-shelf rackno 1 shelfno 1 shelftype IEC_SHELFZXAN(config)#add-card rackno 1 shelfno 1 slotno 0 PRWGZXAN(config)#add-card rackno 1 shelfno 1 slotno 1 PRWGZXAN(config)#add-card rackno 1 shelfno 1 slotno 2 ETGOZXAN(config)#add-card rackno 1 shelfno 1 slotno 3 GTGOZXAN(config)#add-card rackno 1 shelfno 1 slotno 19 GUFQ查看卡槽信息ZXAN(config)#show cardRack Shelf Slot CfgType RealType Port HardV er SoftV er Status-------------------------------------------------------------------------------1 1 0 PRWG PRWG 0 INSERVICE 1 1 1 PRWG PRWG 0 NOPOWER 1 12 ETGO ETGOD 8 091201 V1.2.3P3 INSERVICE 1 1 3 GTGO GTGOA 8 080802 V1.2.3P3 INSERVICE 1 1 10 SCXM SCXM 0 090700 V1.2.3P3 STANDBY 1 1 11 SCXM SCXM 0 090700 V1.2.3P3 INSERVICE 1 1 19 GUFQ GUFQ4 090200 V1.2.3P3 INSERVICEZXAN(config)#show running-configadd-rack rackno 1 racktype IEC19add-shelf rackno 1 shelfno 1 shelftype IEC_SHELFadd-card rackno 1 shelfno 1 slotno 0 PRWGadd-card rackno 1 shelfno 1 slotno 1 PRWGadd-card rackno 1 shelfno 1 slotno 2 ETGOadd-card rackno 1 shelfno 1 slotno 3 GTGOadd-card rackno 1 shelfno 1 slotno 19 GUFQadd-card rackno 1 shelfno 1 slotno 20 GUFQ2、创建VLAN 100 200 并配置各vlan的ip地址，以便后期检测链路的正确性ZXAN(config)#vlan databaseZXAN(vlan)#vlan 100ZXAN(config-vlan)#exitZXAN(config)#inter vlan 100ZXAN(config-if)#ip address 192.168.128.232 255.255.255.0ZXAN(config-if)#exitZXAN(config)#vlan 200ZXAN(config-vlan)#exitZXAN(config)#inter vlan 200ZXAN(config-if)#ip address 192.168.200.200 255.255.255.0ZXAN(config-if)#exitZXAN(config)#epononu认证模式只对epon卡槽有效ZXAN(config-epon)#onu-authentication-mode auth-loid-as-sn 1/2 enable3、创建ONU的流量模板ZXAN(config-epon)#onu-sla-pro create 10MZXAN(config-epon)#onu-sla-pro 10M upstream assured 5000 maximum 10000ZXAN(config-epon)#onu-sla-pro 10M downstream maximum 10000ZXAN(config-epon)#exit4、创建SIP模板ZXAN(config-epon)#sip-pro register-server ip 192.168.128.70ZXAN(config-epon)#sip-pro backup-register-server ip 192.168.128.70ZXAN(config-epon)#sip-pro proxy-server ip 192.168.128.70ZXAN(config-epon)#sip-pro backup-proxy-server ip 192.168.128.70ZXAN(config-epon)#sip-pro outbound-server ip 192.168.128.705、创建fax模板ZXAN(config-epon)#fax pro t38 disable control-mode ss6、创建h248模板ZXAN(config-epon)#h248-pro register-server ip 192.168.128.70 port 5060ZXAN(config-epon)#h248-pro backup-register-server ip 192.168.128.70 port 5060ZXAN(config-epon)#h248-pro mg register-mode ip port 5060ZXAN(config-epon)#h248-pro heartbeat-mode h248ctc rtp-link-test disable cycle 30 count 37、创建VOIP-IP模板ZXAN(config-epon)#voip-vlan pro tag-mode tag cvlan 300 priority 78、创建VOIP-VLAN模板ZXAN(config-epon)#voip-ip pro relation independent mode static gateway 192.168.128.1 dns 192.168.128.1ZXAN(config)#show running-configeponvoip-ip pro relation independent mode static gateway 192.168.128.1 dns 192.168.128.1voip-vlan pro tag-mode tag cvlan 300 priority 7h248-pro register-server ip 192.168.128.70 port 5060h248-pro backup-register-server ip 192.168.128.70 port 5060h248-pro heartbeat-mode h248ctc rtp-link-test disable cycle 30 count 3h248-pro mg register-mode ip port 5060sip-pro register-server ip 192.168.128.70 port 5060sip-pro backup-register-server ip 192.168.128.70 port 5060sip-pro proxy-server ip 192.168.128.70 port 5060sip-pro backup-proxy-server ip 192.168.128.70 port 5060sip-pro outbound-server ip 192.168.128.70 port 5060sip-pro register-interval 3600sip-pro heartbeat enable cycle 20 count 3sip-pro mg port 5060fax pro t38 disable control-mode ss!重命名ONU-sla名字ZXAN(config-epon)#onu-sla-pro rename oldname xlxh-onu-dba newname onu-sla-test 配置改ONU-type不会自动下发配置ZXAN(config)#eponZXAN(config-epon)#auto-dispatch-set ZTE-EPON disableZXAN(config-epon)#exit9、配置ONU-TYPE如果OLT没有配置ONU-type则需要自己配置ONU-typeZXAN(config)#ponZXAN(config-pon)#onu-type ZTE-EPON epon description 804WZXAN(config-pon)#onu-type-if ZTE-EPON eth_0/1-4ZXAN(config-pon)#show onu-type epon ZTE-EPONOnu type name: ZTE-EPONPon type: eponDescription: 804WProtect type: noneSpeed: 1gZXAN(config-pon)#exit10、配置带宽业务10.1、查询未注册的ONUZXAN(config)#inter epon-olt_1/2/1ZXAN(config-if)#show onu unauthenticationOnu Interface : epon-onu_1/2/1:1Onu Model : RL-4WMAC Address : 1c18.4a0d.d30fSN :LOID :LOID_PSW :Online State : authentication denyExtOam State : completeSoftware Version : 6151Hardware Version : v1.0_01RegTime : 2015/07/22 10:43:06ZXAN(config-if)#exit10.2、注册ONUZXAN(config-if)#onu 1 type ZTE-EPON mac 1c18.4a0d.d30fZXAN(config-if)#show onu detail-info epon-onu_1/2/1:110.3、进入ONU端口下配置业务端口VLANZXAN(config)#inter epon-onu_1/2/1:1ZXAN(config-if)#sla-proZXAN(config-if)#switchport vlan 200 tagZXAN(config-if)#exit10.4、上行添加ＶＬＡＮZXAN(config)#inter gei_1/19/1ZXAN(config-if)#switchport default vlan 100ZXAN(config-if)#switchport vlan 200 tagZXAN(config)#inter gei_1/19/2ZXAN(config-if)#switchport vlan 200 tagZXAN(config-if)#switchport default vlan 100ZXAN(config-if)#exit10.5、远程ONU下配置用户侧VLAN由于带WiFi的onu带有web管理界面；在web页面上配置vlan相当于untag vlan ZXAN(config)#pon-onu-mng epon-onu_1/2/1:1ZXAN(epon-onu-mng)#vlan port eth_0/1 mode transparentZXAN(epon-onu-mng)#exitZXAN(config)#exit11、保存配置ZXAN#writeZXAN(config)#show runningvlan databasevlan 1,100,200,300!!epononu-authentication-mode auth-loid-as-sn 1/2 enableencrypt algorithm 1/2 triple-churning key-update-period 20 churning-timer 3onu-sla-pro create onu-sla-testonu-sla-pro onu-sla-test upstream fixed 0 fixedpkt 64 assured 102400 maximum 1024000maxburst 45000 priority 0onu-sla-pro onu-sla-test downstream maximum 1024000onu-sla-pro create 10Monu-sla-pro 10M upstream fixed 0 fixedpkt 64 assured 5000 maximum 10000 maxburst 45000 priority 0onu-sla-pro 10M downstream maximum 10000auto-dispatch-set ZTE-EPON disable!pononu-type ZTE-EPON epon description 804Wonu-type-if ZTE-EPON eth_0/1onu-type-if ZTE-EPON eth_0/2onu-type-if ZTE-EPON eth_0/3onu-type-if ZTE-EPON eth_0/4uncfg-onu-display-info sn pw!interface vlan 100ip address 192.168.128.232 255.255.255.0!interface vlan 200ip address 192.168.200.200 255.255.255.0!interface vlan 300ip address 192.168.100.100 255.255.255.0!interface null1!interface epon-olt_1/2/1p2p mode grouponu 1 type ZTE-EPON mac 1c18.4a0d.d30f ip-cfg static !interface epon-onu_1/2/1:1admin enablesla-pro vport 1encrypt direction downstream enable vport 1ems-autocfg-request disableswitchport mode hybrid vport 1switchport vlan 100 tag vport 1!!interface gei_1/19/1hybrid-attribute fibernegotiation autoflowcontrol disableport-protect disableuplink-isolate disableswitchport mode hybridswitchport default vlan 100switchport vlan 200 tag!interface gei_1/19/2hybrid-attribute fibernegotiation autoflowcontrol disableport-protect disableuplink-isolate disableswitchport mode hybridswitchport default vlan 100!二、配置不带WIFI的EPON ONU RL804C || 804FCZXAN(config)#RL804C || 804FCZXAN(config)#show onu unauthenticationOnu Interface : epon-onu_1/2/1:1Onu Model : RL-4FCMAC Address : 1c18.4a0f.e563SN :LOID :LOID_PSW :Online State : authentication denyExtOam State : completeSoftware Version : 6151Hardware Version : v1.0_01RegTime : 2015/07/22 13:44:41ZXAN(config-if)#show running-config inter epon-olt_1/2/1!interface epon-olt_1/2/1p2p mode grouponu 1 type ZTE-EPON mac 1c18.4a0d.d30f ip-cfg static!ZXAN(config-if)#interface epon-olt_1/2/1ZXAN(config-if)#onu 2 type ZTE-EPON mac 1c18.4a0f.e563ZXAN(config)#inter epon-onu_1/2/1:2ZXAN(config-if)#switchport vlan 100 tagZXAN(config-if)#switchport vlan 200 tagZXAN(config-if)#exitZXAN(config)#pon-onu-mng epon-onu_1/2/1:2ZXAN(epon-onu-mng)#vlan port eth_0/1 mode tag vlan 100 priority 0 ZXAN(epon-onu-mng)#vlan port eth_0/2 mode tag vlan 200 priority 1ZXAN(epon-onu-mng)#show running-configadd-rack rackno 1 racktype IEC19add-shelf rackno 1 shelfno 1 shelftype IEC_SHELFadd-card rackno 1 shelfno 1 slotno 0 PRWGadd-card rackno 1 shelfno 1 slotno 1 PRWGadd-card rackno 1 shelfno 1 slotno 2 ETGOadd-card rackno 1 shelfno 1 slotno 3 GTGOadd-card rackno 1 shelfno 1 slotno 19 GUFQsystem-monitor watchdog rackno 1 shelfno 1 slotno 0 disablesystem-monitor watchdog-duration rackno 1 shelfno 1 slotno 0 value 5 system-monitor endless-loop duration rackno 1 shelfno 1 slotno 0 value 75 system-monitor endless-loop reboot rackno 1 shelfno 1 slotno 0 disable system-monitor task-suspend-reboot rackno 1 shelfno 1 slotno 0 all system-monitor watchdog rackno 1 shelfno 1 slotno 1 disablesystem-monitor watchdog-duration rackno 1 shelfno 1 slotno 1 value 5 system-monitor endless-loop duration rackno 1 shelfno 1 slotno 1 value 75 system-monitor endless-loop reboot rackno 1 shelfno 1 slotno 1 disable system-monitor task-suspend-reboot rackno 1 shelfno 1 slotno 1 all system-monitor watchdog rackno 1 shelfno 1 slotno 2 disablesystem-monitor watchdog-duration rackno 1 shelfno 1 slotno 2 value 5 system-monitor endless-loop duration rackno 1 shelfno 1 slotno 2 value 75 system-monitor endless-loop reboot rackno 1 shelfno 1 slotno 2 disable system-monitor task-suspend-reboot rackno 1 shelfno 1 slotno 2 all system-monitor watchdog rackno 1 shelfno 1 slotno 3 disablesystem-monitor watchdog-duration rackno 1 shelfno 1 slotno 3 value 5 system-monitor endless-loop duration rackno 1 shelfno 1 slotno 3 value 75 system-monitor endless-loop reboot rackno 1 shelfno 1 slotno 3 disable system-monitor task-suspend-reboot rackno 1 shelfno 1 slotno 3 all system-monitor watchdog rackno 1 shelfno 1 slotno 10 enablesystem-monitor watchdog-duration rackno 1 shelfno 1 slotno 10 value 5 system-monitor endless-loop duration rackno 1 shelfno 1 slotno 10 value 75 system-monitor endless-loop reboot rackno 1 shelfno 1 slotno 10 disable system-monitor task-suspend-reboot rackno 1 shelfno 1 slotno 10 all system-monitor watchdog rackno 1 shelfno 1 slotno 11 enablesystem-monitor watchdog-duration rackno 1 shelfno 1 slotno 11 value 5 system-monitor endless-loop duration rackno 1 shelfno 1 slotno 11 value 75 system-monitor endless-loop reboot rackno 1 shelfno 1 slotno 11 disable system-monitor task-suspend-reboot rackno 1 shelfno 1 slotno 11 all system-monitor watchdog rackno 1 shelfno 1 slotno 19 disablesystem-monitor watchdog-duration rackno 1 shelfno 1 slotno 19 value 5 system-monitor endless-loop duration rackno 1 shelfno 1 slotno 19 value 75 system-monitor endless-loop reboot rackno 1 shelfno 1 slotno 19 disable system-monitor task-suspend-reboot rackno 1 shelfno 1 slotno 19 all!vlan databasevlan 1,100,200,300!!epononu-authentication-mode auth-loid-as-sn 1/2 enableencrypt algorithm 1/2 triple-churning key-update-period 20 churning-timer 3onu-sla-pro create onu-sla-testonu-sla-pro onu-sla-test upstream fixed 0 fixedpkt 64 assured 102400 maximum 1024000maxburst 45000 priority 0onu-sla-pro onu-sla-test downstream maximum 1024000onu-sla-pro create 10Monu-sla-pro 10M upstream fixed 0 fixedpkt 64 assured 5000 maximum 10000 maxburst 45000 priority 0onu-sla-pro 10M downstream maximum 10000auto-dispatch-set ZTE-EPON disable!!pononu-type ZTE-EPON epon description 804Wonu-type-if ZTE-EPON eth_0/1onu-type-if ZTE-EPON eth_0/2onu-type-if ZTE-EPON eth_0/3onu-type-if ZTE-EPON eth_0/4uncfg-onu-display-info sn pw!interface mng1ip address 136.1.1.100 255.255.255.0boot-server 192.168.110.2boot-username xlxhconfig- startrun.datimg local!interface vlan 100ip address 192.168.128.232 255.255.255.0!interface vlan 200ip address 192.168.200.200 255.255.255.0!interface vlan 300ip address 192.168.100.100 255.255.255.0!interface null1!interface epon-olt_1/2/1p2p mode grouponu 1 type ZTE-EPON mac 1c18.4a0d.d30f ip-cfg static onu 2 type ZTE-EPON mac 1c18.4a0f.e563 ip-cfg static !interface epon-onu_1/2/1:1admin enablesla-pro vport 1encrypt direction downstream enable vport 1ems-autocfg-request disableswitchport mode hybrid vport 1switchport vlan 100,200 tag vport 1!interface epon-onu_1/2/1:2admin enableencrypt direction downstream enable vport 1ems-autocfg-request disableswitchport mode hybrid vport 1switchport vlan 100,200 tag vport 1!interface gei_1/19/1hybrid-attribute fibernegotiation autoflowcontrol disableport-protect disableuplink-isolate disableswitchport mode hybridswitchport default vlan 100switchport vlan 200 tag!interface gei_1/19/2hybrid-attribute fibernegotiation autoflowcontrol disableport-protect disableuplink-isolate disableswitchport mode hybridswitchport default vlan 100switchport vlan 200,300 tag!!!pon-onu-mng epon-onu_1/2/1:1no auto-configvlan port eth_0/1 mode transparent!!pon-onu-mng epon-onu_1/2/1:2no auto-configvlan port eth_0/1 mode tag vlan 100 priority 0vlan port eth_0/2 mode tag vlan 200 priority 1!eponvoip-ip pro relation independent mode static gateway 192.168.128.1 dns 192.168.128.1 voip-vlan pro tag-mode tag cvlan 300 priority 7h248-pro register-server ip 192.168.128.70 port 5060h248-pro backup-register-server ip 192.168.128.70 port 5060h248-pro heartbeat-mode h248ctc rtp-link-test disable cycle 30 count 3h248-pro mg register-mode ip port 5060sip-pro register-server ip 192.168.128.70 port 5060sip-pro backup-register-server ip 192.168.128.70 port 5060sip-pro proxy-server ip 192.168.128.70 port 5060sip-pro backup-proxy-server ip 192.168.128.70 port 5060sip-pro outbound-server ip 192.168.128.70 port 5060sip-pro register-interval 3600sip-pro heartbeat enable cycle 20 count 3sip-pro mg port 5060fax pro t38 disable control-mode ss!12、配置RL804系列不带WiFi的vlan业务配置方式一：通过trunk vlan配置，但是起不到端口隔离的作用；ZXAN(epon-onu-mng)#vlan port eth mode hybrid def-vlan 200 vlan-list 100ZXAN(epon-onu-mng)#vlan port eth_0/2 mode trunk vlan-list 100 def-vlan 200三四口的方式配置；起到端口隔离作用；可以配置不同的业务vlanZXAN(epon-onu-mng)#vlan port eth_0/3 mode tag vlan 100 priority 0ZXAN(epon-onu-mng)#vlan port eth_0/4 mode tag vlan 200 priority 013、配置RL804W系列带WiFi的vlan业务配置pon-onu-mng epon-onu_1/2/1:1no auto-configvlan port eth_0/1 mode transparent804W WEB 管理界面配置这样能实现配置两个业务vlan的功能2、如果配置eth1 口为路由DHCP 绑定1 口；可以上网，但是如果eth2 绑定的vlan200 也是Internet route模式；则接入2 口也能ping通eth1 口绑定的vlan1003、如果配置eth1 口为路由DHCP 绑定1 口；可以上网，但是如果eth2 绑定的vlan200 是other 桥模式；则接入2 口不能ping通eth1 口绑定的vlan 100 起到两个业务分配的效果14、中兴对接GPON ONU的配置14.1 配置ONU-type gpononu-type ZTE-EPON epon description 804Wonu-type ZTE-GPON gpon description 1GE+4FE+2POTS onu-type ZTE-GPON gpon max-tcont 8onu-type ZTE-GPON gpon max-gemport 32onu-type ZTE-GPON gpon max-switch-perslot 32onu-type ZTE-GPON gpon max-flow-perswitch 32onu-type ZTE-GPON gpon max-iphost 1onu-type-if ZTE-GPON eth_0/1onu-type-if ZTE-GPON eth_0/2onu-type-if ZTE-GPON eth_0/3onu-type-if ZTE-GPON eth_0/4onu-type-if ZTE-GPON pots_0/1onu-type-if ZTE-GPON pots_0/2uncfg-onu-display-info sn pw配置gpon ONU对接OLT14.2、查询未注册的ONUZXAN(config)#show gpon onu uncfgOnuIndex Sn State---------------------------------------------------------------------gpon-onu_1/3/1:1 GPON12345678 unknown ZXAN(config)#14.2、注册gpon ONUZXAN(config-if)#onu 1 type ZTE-GPON sn?sn Serial number authentication modesn+pw Sn+pw authentication modesn+hpw Sn+hpw authentication modesn+rid sn+rid authentication mode(XGPON)ZXAN(config-if)#onu 1 type ZTE-GPON sn GPON12345678 ?vport-mode Vport configuration mode<cr>ZXAN(config-if)#onu 1 type ZTE-GPON sn GPON12345678.[Successful]ZXAN(config-if)#14.3、配置tcont 带宽模板ZXAN(config)#gponZXAN(config-gpon)#profile ?tcont Configure T-CONT profiletraffic Configure traffic pro(config-gpon)#pro 100M type ?1 -Fixed bandwidth2 -Assured bandwidth3 -Assured bandwidth and Non-assured bandwidth4 -Best-effort bandwidth5 -The super set of all of T-CONT typesZXAN(config-gpon)#pro 100M type 3 assured 100000 maximum 1024000 [Successful]ZXAN(config-gpon)#14.4、配置ONU-SIP模板ZXAN(config-gpon)#onu pro sip-test proxy 192.168.128.7014.5、配置带宽业务端口ZXAN(config)#inter gpon-onu_1/3/1:1ZXAN(config-if)#tcont 1 name tcont1 proZXAN(config-if)# gemport 1 name gemport1 unicast tcont 1 dir both queue 1 ZXAN(config-if)# service-port 1 user-vlan 300 vlan 10014.6、配置业务通道pon-onu-mng gpon-onu_1/3/1:1service internet type internet gemport 1 vlan 300switchport-bind switch_0/1 veip 1!!14.7、配置用户侧VLAN15、配置gpon-onu的线路模板onu-pro line line-gpontcont 1 name tcont1 protcont 1 gap mode3gemport 1 unicast tcont 1 dir both queue 1!pon!16、配置gpon-onu远程管理模板方式一：pononu-pro remote remote-gponservice date type internet gemport 1 cos 0 vlan 300switchport-bind switch_0/1 veip 1!方式二：pononu-pro remote remote-cvlan300service intenet gemport 1 vlan 300veip 1 inter-domain test1switchport-bind switch_0/1 veip 1vlan-filter-mode veip 1 tag-filter vid-match untag-filter discardvlan-filter veip 1 priority 0 vid 300ex-vlan veip 1 input-tpid 0x8100 output-tpid 0x8100 down-mode inverse-upstream !17、加入已配置的线路模板和远程onu模板（下面即配置带宽业务）ZXAN(config)#inter gpon-olt_1/3/1ZXAN(config-if)#onu 1 profile ?alarm Alarm profileline Line profileperformance Performance profileremote Remote pro(config-if)#onu 1 pro line-gponZXAN(config-if)#onu 1 profiler remote remote-gpon17.1 在onu接口下配置业务VLANZXAN(config)#inter gpon-olt_1/3/1：1ZXAN(config-if)# service-port 1 user-vlan 300 vlan 100。
ZTE C200 OLT基本配置方法
ZTE C200 OLT 配置username : ztepassword : zteZXAN(config)#config tershow onu-typeZXAN(config)#show onu-typpon type Onu type Description------------------------------------------------------------------------------------epon ZTE-9806 0epon ZTE-D400 4FE /*F23*/ epon ZTE-D402 8FEepon ZTE-D420 4FE, 2Pots /*TWF23*/ epon ZTE-D421 4FE, 1wifiepon ZTE-D422epon ZTE-F401 1GE############ 配置bandwidth-profile ################ZXAN(config)#eponZXAN(config-epon)#bandwidth-profile profile-name create 28ZXAN(config-epon)# bandwidth-profile profile-set 28 downstream maximum 800000ZXAN(config-epon)# bandwidth-profile profile-set 28 upstream maximum 800000ZXAN(config-epon)# exit############ 配置上联口vlan ##################ZXAN(config)#interface gei_0/4/3ZXAN(config-if)# switchport mode hybridZXAN(config-if)# no switchport default vlanZXAN(config-if)# switchport vlan 500-527 tagZXAN(config-if)# exit########## Create ONU ####################-------------------*******----------------------------------- /*在OLT下配置ONU */ZXAN(config)#interface epon-olt_0/3/3ZXAN(config-if)#onu 1 type ZTE-F401 mac 0000.62ee.eeeeZXAN(config-if)#show onu all-status epon-olt_0/3/3ZXAN(config-if)#interface epon-olt 0/3/1------------------------onu 1 type ZTE-F401 mac 0000.C000.0001onu 2 type ZTE-F401 mac 0000.C000.0002onu 3 type ZTE-F401 mac 0000.C000.0003onu 4 type ZTE-F401 mac 0000.C000.0004ZXAN(config-if)#exit######### 配置ONU ###############ZXAN(config)#interface epon-onu_0/3/1:1ZXAN(config-if)#activate #激活#ZXAN(config-if)#authentication enable #开启认证#ZXAN(config-if)#no bandwidth-profileZXAN(config-if)#bandwidth-profile 28 # #绑定bandwidth-profile ##ZXAN(config-if)#switchport mode hybrid #配置pon 口vlan 这是配置olt上的不会下发onu# ZXAN(config-if)#no switchport default vlanZXAN(config-if)#switchport default vlan 528ZXAN(config-if)#switchport vlan 100-110 tagZXAN(config-if)#encrypt direction downstream disable #关闭下行方向三重搅动/可选/ # ZXAN(config-if)#exit########## ONU端VLAN mode #################pon-onu-mng epon-onu_0/3/1:2vlan port eth_0/1 mode transparentexitinterface epon-onu_0/3/1:2activateauthentication enableenableencrypt direction downstream disablebandwidth-profile 28switchport mode hybridswitch default vlan 528switch vlan 500-527 tagswitchport vlan 4000-4096 tagexitpon-onu-mng epon-onu_0/3/1:2vlan port eth_0/1 mode transparentexitinterface epon-onu_0/3/1:3activateauthentication enableenableencrypt direction downstream disablebandwidth-profile 28switchport mode hybridswitchport default vlan 528switchport vlan 500-527 tagswitchport vlan 4000-4096 tagexitpon-onu-mng epon-onu_0/3/1:3vlan port eth_0/1 mode transparentexit********************* onu 4 ***************************interface epon-onu_0/3/1:4activateauthentication enableenableencrypt direction downstream disablebandwidth-profile 28switchport mode hybridswitchport default vlan 528switchport vlan 500-527 tagswitchport vlan 4000-4094 tagexitpon-onu-mng epon-onu_0/3/1:4vlan port eth_0/1 mode transpanentexit*********************************************************############配置onu classification ################ZXAN(epon-onu-mng)#---------------------------------smac based ------------------------ classification rule-profile 5 queue 3 priority 1classification rule-profile 6 queue 2 priority 2classification rule-profile 7 queue 1 priority 3classification rule-profile 8 queue 0 priority 4classification condition-profile 15 smac 0000.0000.00a1 operation-type equal classification condition-profile 16 smac 0000.0000.00a2 operation-type equal classification condition-profile 17 smac 0000.0000.00a3 operation-type equal classification condition-profile 18 smac 0000.0000.00a4 operation-type equal classification port eth_0/1 rule-precedence 5 add 5 15classification port eth_0/1 rule-precedence 6 add 6 16classification port eth_0/1 rule-precedence 7 add 7 17classification port eth_0/1 rule-precedence 8 add 8 18-------------------------- vlanid based -------------------------classification rule-profile 5 queue 3 priority 1classification rule-profile 6 queue 2 priority 2classification rule-profile 7 queue 1 priority 3classification rule-profile 8 queue 0 priority 4classification condition-profile 15 vlanId 501 operation-type equal classification condition-profile 16 vlanId 502 operation-type equal classification condition-profile 17 vlanId 503 operation-type equal classification condition-profile 18 vlanId 504 operation-type equal classification port eth_0/1 rule-precedence 5 add 5 15classification port eth_0/1 rule-precedence 6 add 6 16classification port eth_0/1 rule-precedence 7 add 7 17classification port eth_0/1 rule-precedence 8 add 8 18--------------------- priority based ----------------------------classification rule-profile 5 queue 3 priority 1classification rule-profile 6 queue 2 priority 2classification rule-profile 7 queue 1 priority 3classification rule-profile 8 queue 0 priority 4classification condition-profile 15 priority 1 operation-type equal classification condition-profile 16 priority 2 operation-type equal classification condition-profile 17 priority 3 operation-type equal classification condition-profile 18 priority 4 operation-type equal classification port eth_0/1 rule-precedence 5 add 5 15classification port eth_0/1 rule-precedence 6 add 6 16classification port eth_0/1 rule-precedence 7 add 7 17classification port eth_0/1 rule-precedence 8 add 8 18---------------------------src IP based ------------------------------------classification rule-profile 5 queue 3 priority 1classification rule-profile 6 queue 2 priority 2classification rule-profile 7 queue 1 priority 3classification rule-profile 8 queue 0 priority 4classification condition-profile 15 srcIp 192.168.1.1 operation-type equalclassification condition-profile 16 srcIp 192.168.1.1 operation-type equalclassification condition-profile 17 srcIp 192.168.1.3 operation-type equalclassification condition-profile 18 srcIp 192.168.1.4 operation-type equalclassification port eth_0/1 rule-precedence 5 add 5 15classification port eth_0/1 rule-precedence 6 add 6 16classification port eth_0/1 rule-precedence 7 add 7 17classification port eth_0/1 rule-precedence 8 add 8 18---------------------dstIP based----------------------------------classification rule-profile 5 queue 3 priority 1classification rule-profile 6 queue 2 priority 2classification rule-profile 7 queue 1 priority 3classification rule-profile 8 queue 0 priority 4classification condition-profile 15 dstIp 192.168.1.1 operation-type equalclassification condition-profile 16 dstIp 192.168.1.1 operation-type equalclassification condition-profile 17 dstIp 192.168.1.3 operation-type equalclassification condition-profile 18 dstIp 192.168.1.4 operation-type equalclassification port eth_0/1 rule-precedence 5 add 5 15classification port eth_0/1 rule-precedence 6 add 6 16classification port eth_0/1 rule-precedence 7 add 7 17classification port eth_0/1 rule-precedence 8 add 8 18---------------------dscp based -----------------------------------classification rule-profile 5 queue 3 priority 1classification rule-profile 6 queue 2 priority 2classification rule-profile 7 queue 1 priority 3classification rule-profile 8 queue 0 priority 4classification condition-profile 15 dscp 1 operation-type equalclassification condition-profile 16 dscp 2 operation-type equalclassification condition-profile 17 dscp 3 operation-type equalclassification condition-profile 18 dscp 4 operation-type equalclassification port eth_0/1 rule-precedence 5 add 5 15classification port eth_0/1 rule-precedence 6 add 6 16classification port eth_0/1 rule-precedence 7 add 7 17classification port eth_0/1 rule-precedence 8 add 8 18------------------------------------------------------------------------ZXAN(epon-onu-mng)#interface eth eth_0/1 auto-neg #onu uni 1 auto-negotiate ZXAN(epon-onu-mng)#interface eth eth_0/1 flow-controlZXAN(epon-onu-mng)#interface eth eth_0/1 phy-state #physical port state ZXAN(epon-onu-mng)#interface eth eth_0/1 policing #Ingress policing ZXAN(epon-onu-mng)#fastleave#enable/disable fastleaveZXAN(epon-onu-mng)#fec#enable/disble fec##### 配置onu multicast ########ZXAN(epon-onu-mng)#multicast vlan port eth_0/1 add vlanlist 4000 #add mvlanZXAN(epon-onu-mng)#multicast vlan port eth_0/1 delete vlanlist 4000 #del mvlanZXAN(epon-onu-mng)#multicast vlan port eth_0/1 clear #clear mvlanZXAN(epon-onu-mng)#multicast group-max-number eth_0/1 32 #config max group ZXAN(epon-onu-mng)#multicast switch igmpsnooping # multicast snooping mode ZXAN(epon-onu-mng)#multicast switch control-multicast # multicast CTC modeZXAN(epon-onu-mng)#multicast control-type gda-ip-and-vlan #组播控制类型切换#### holdover 开关###########ZXAN(epon-onu-mng)#holdover disable/enable清除配置ZXAN(config-if)# no onu id# <1-64> onu id #。
中兴OLT配置
OLT开局配置提示符命令> enablePassword: zxr10 密码ZXAN# dir 查询flash保存的文件目录ZXAN# cd cfg 进入配置文件夹cfgZXAN# del cfg *、*ZXAN# Reboot 重启ZXAN# Show runZXAN# conf t 全局模式ZXAN(config)# hostname OLT 进入OLTOLT(config)# username zte password zte private 10 //远程登录用户名与密码OLT(config)# Enable secret zte //enable密码OLT(config)# exitOLT# show runOLT# show card 查瞧设备OLT# conf t 全局s add-rack rackno 0 racktype ZXPON 添加机架OLT (config)# add-shelf shelfno 0 shelftype ZXA10C200-A 添加机框OLT (config)# show card //直到EPFC卡出现在real硬件中OLT (config)# add-card slotno 2 EPFC 在2号槽添加EPFC板OLT (config)# Master-backup enable rackno 0 shelfno 0 删除主控板OLT (config)# show card //直到所有EPFC、EC4GM卡出现在ctgtype与realtype中OLT# Write保存OLT# Conf tOLT(config)# inter epon-olt_0/1/2 进入端口0/1/2OLT(config-if)# Show onu-typeOLT(config-if)# endOLT# Show onu unauth epon-olt_0/2/1 //查瞧ONU interface与MAC address OLT# Conf tOLT(config)# inter epon-olt_0/1/2OLT(config-if)# onu 1 type ZTE-D420 mac 001e、73e5、fb62OLT(config-if)# Show onu unauth epon-olt_0/2/1 //直到no relate information to show OLT(config-if)# exitOLT(config)# inter epon-onu_0/2/1:1OLT(config-if)# Authentication enableOLT(config-if)# endOLT# show onu detail-info epon-onu_0/2/1:1//直到adminstate为enable,Regstate为Registered OLT# Conf tOLT(config)# snmp-server host 192、168、88、100trap version 2c zte enable NOTI server-index 1// 网管信息上传到192、168、88、100OLT(config-if)# show run //保证有snmp trap信息OLT# conf tOLT# show nvram runOLT# conf tOLT(config)# nvram mng-ip-add 192、168、40、1 255、255、255、0 //带外网管IP OLT(config)# exitOLT# show nvram runOLT# conf tOLT(config)# vlan 88OLT(config-vlan)# exitOLT(config)# interface vlan 88OLT(config-if)# ip add 192、168、88、1 255、255、255、0 //带内网管IPOLT(config-if)# exitOLT(config)# inter epon-onu_0/2/1:1OLT(config-if)# switchport mode hybrid //或trunkOLT(config-if)# switchport vlan 10,50,88,100 tag // 语音、视频、上网数据、网管OLT(config-if)# show run //保证epon-onu_0/2/1:1接口的vlan OLT(config)# inter gei_0/4/4OLT(config-if)# switchport mode hybrid //或trunkOLT(config-if)# switchport vlan 10,50,88,100 tagOLT(config-if)# shutdownOLT(config-if)# no shutdown //确保上联口upOLT(config-if)# endOLT# Conf tOLT(config)# pon-onu-mng epon-onu_0/2/1:1OLT(config-onu-mng)# Mgmt-ip onu-ip 192、168、88、11 255、255、255、0 7 88 mgm-ip 192、168、0、0 255、255、0、0 192、168、88、254 status enable//远程管理ONU的IP,并指定静态路由OLT(config-onu-mng)# endOLT# Ping 192、168、88、11 //保证OLT与ONU连通OLT# Conf tOLT(config)# pon-onu-mng epon-onu_0/2/1:1OLT(config-onu-mng)# Vlan port eth_0/1 mode tag vlan 10 priority 6OLT(config-onu-mng)# Vlan port eth_0/1 mode tag vlan 0 priority 4OLT(config-onu-mng)# Vlan port eth_0/2 mode tag vlan 50 priority 4OLT(config-onu-mng)# Vlan port eth_0/2 mode tag vlan 0 priority 5OLT(config-onu-mng)# Vlan port eth_0/3 mode tag vlan 100 priority 5OLT(config-onu-mng)# exitOLT(config)# exitOLT# writeCISCO> enable //如何切换成CISCO？CISCO # conf tCISCO(config) # Vlan 10CISCO(config-vlan) # exitCISCO(config) # vlan 50CISCO(config-vlan) # exitCISCO(config) # vlan 88CISCO(config-vlan) # exitCISCO(config) # vlan 100CISCO(config-vlan) # exitCISCO(config) # inter f0/4CISCO(config-if) # Sw mode trunkCISCO(config-if) # Sw trunk allow allCISCO(config) # inter f0/5CISCO(config-if) # Sw mode accessCISCO(config-if) # Sw access vlan 50CISCO(config) # inter f0/10CISCO(config-if) # Sw mode accessCISCO(config-if) # Sw access vlan 100CISCO # show run // f0/1 in vlan100,Access口;f0/2 in vlan50,Access口CISCO # erase startup-configCISCO # reloadCISCO> enableCISCO # show vlan //vlan50含f0/2,vlan88, vlan100含f0/1,f0/23, vlan200 CISCO # conf tCISCO(config) # vlan databaseCISCO(config) # no vlan 50 88 100 200CISCO(config) # endC ISCO # show vlan //确保vlan清空C ISCO # conf tCISCO(config) # interface range fastethernet 0/1-24CISCO(config-range) # Sw mode accessCISCO(config-range) # Sw access vlan 1CISCO(config-range) # endC ISCO # show vlanC ISCO # Show ip in bIngter f0/4C ISCO # conf tCISCO(config) #OLT# conf tOLT(config)# vlan 200 //VOIP业务OLT(config-vlan)# exitOLT(config)# Show vlan summary。
实验1 中兴OLT基本操作
实验一中兴OLT基本操作一、实验目的：1．了解实验室设备组网情况；2．熟悉C200/C220设备结构；3．了解和掌握C200的基本操作命令；4．开通网元带内，带外网管；二、实验设备：C200、ZXR10 2826、ZXR10 3928、电脑、串口线、网线、光纤三、实验内容与步骤1.串口登录计算机通过串口线与交换主控处理板的CONSOLE口连接。
用超级终端登录设备。
在运行Windows操作系统的PC上启动超级终端程序，选择串口和波特率，配置结束后，点击“确定”按钮，即可进入本地操作维护登录界面。
使用“enable”命令，登录到超级用户权限，密码是“zxr10”。
2．设备基本信息查询（1）查询设备版本信息ZXAN#show version-running 察看运行的版本信息Shelf/Slot VerType FileType V erTag VerLenth BuildTime--------------------------------------------------------------------------------0/0/1 EPFC MVR V1.1.1ET9 185**** ****-03-01 17:28:10 0/0/1 EPFC BOOTROM V1.1.1ET8 271072 2008-02-16 14:03:41 0/0/4 EC4G MVR V1.1.1ET9 9366418 2008-03-01 18:02:51 0/0/4 EC4G BOOTROM V1.1.1ET8 358752 2008-02-16 14:02:56ZXAN#show version-saved 察看保存的版本信息Shelf/Slot FileName VerType VerTag BuildTime VerLenth Active--------------------------------------------------------------------------------0/0/1 epfc.mvr EPFC V1.1.1ET9 2008-03-01 17:28:10 1853485 00/0/4 ec4g.mvr EC4G V1.1.1ET9 2008-03-01 18:02:51 9366418 1 （2）察看设备单板状态ZXAN#show cardRack Shelf Slot CfgType RealType Port HardVer SoftVer Status-------------------------------------------------------------------------------0 0 1 EPFC EPFC 4 V0 V1.1.1ET9 INSERVICE 0 0 4 EC4GM EC4GM 4 V0 V1.1.1ET9 INSERVICE 0 0 5 EC4GM 4 OFFLINE （3）察看设备的运行配置文件ZXAN#show running-configBuilding configuration...!**********Before interface -- show run on RP start!*********!!add-rack rackno 0 racktype ZXPONadd-shelf rackno 0 shelfno 0 shelftype ZXA10C200master-backup enable rackno 0 shelfno 0add-card rackno 0 shelfno 0 slotno 1 EPFC!clock3．机架配置，机框配置，单板配置（1）机架配置C200设备第一次使用时，必须要先进行机架配置。
OLT(ONU)语音业务数据标准配置指导-zte
中兴语音业务配置流程：（本数据规范以常见开局方式为例）假设在OLT的5板1口下注册一个onu，该onu的语音vlan为3000,语音IP:10.65.3.22,语音网关为：19.65.3.1，主用软交换地址为：10.63.7.97，备用软交换地址为：10.63.7.98.OLT配置数据：（通用于所有onu，只是注册时标注为不同的ONU类型）ZXAN#show onu all-status epon-olt_0/5/1（显示相关PON口下所有ONU的状态，查找没注册的onu）ZXAN#show onu unauthentication epon-olt_0/5/1（显示相关PON口下未注册认证的ONU的mac地址）ZXAN<config>#interface epon-olt_0/5/1（进入PON口）ZXAN<config-if>#onu 1 type ZTE-F820 mac 0015.EB71.F6C8（根据MAC地址添加ONU，如果为9806，onu类型填写ZTE-9806）ZXAN<config>#interface epon-onu_0/5/1:1（进入PON-ONU口）ZXAN<config-if>#authentication enable（开通ONU，新添加的ONU，默认状态是未开通的，故需要执行此命令，否则业务不通）ZXAN<config-if>#bandwidth downstream maximum 100000（设置下行最大带宽）ZXAN<config-if>#bandwidth upstream maximum 100000（设置上行最大带宽）ZXAN<config>#interface epon-onu_0/5/1:1（进入PON-ONU口）ZXAN<config-if>#switchport mode trunk（把端口模式改成trunk）ZXAN<config-if>#switchport vlan 3000 tag（在该端口下以tag方式加入语音VLAN）ZXAN<config># interface gei_0/6/1（进入上联端口）ZXAN<config-if>#switchport vlan 3000 tag（在上联口里以tag方式加入语音VLAN）ZXAN#write （保存数据）F820配置方法：ZXAN(config)#interface fei_0/5/1 //进入语音板的内联口ZXAN(config-if)#show vlan port fei_0/5/1 //查看已配置的配置ZXAN(config-if)#no switchport defaut vlan //删除已配置的VLANZXAN(config-if)#show vlan port fei_0/5/1 //查看是否成功ZXAN(config-if)#switchport vlan 3000 tag //配置语音VLANZXAN(config-if)#show vlan port fei_0/5/1 //查看配置ZXAN(config-if)#exitZXAN(config)#exit进入子卡：ZXAN(config)#voip 5设置子卡ip地址，掩码，网关,静态IP方式：ZXAN(config-voip)# mg net 1 mode 0 ip-address 10.65.3.22 mask 255.255.255.0 gateway 10.65.3.1 vlan-option 1 vlan-id 3000 vlan-priority 7设置协议认证方式为静态IP方式：ZXAN(config-voip)# mg add 1 1 port 2944 mid-flag 0设置主用软交换地址：ZXAN(config-voip)# mgc add 1 ip-address 10.63.7.97 port 2944 md5-profile 1设置备用软交换地址：ZXAN(config-voip)# mgc add 2 ip-address 10.63.7.98 port 2944 md5-profile 1设置心跳检测模式为hw的方式：ZXAN(config-voip)# mgc h248tid test-link-flag 2设置TID和RTP资源：ZXAN(config-voip)# mgc h248tid user-tid-prefix A user-tid-index 0 rtp-tid-prefix RTP/ link-kept-flag 0 link-kept-time 3000设置传真模式为(全控＋T30)：ZXAN(config-voip)# rtp parameter fax-modem t38-enable 0 fax-control 2设置定时器时长：ZXAN(config-voip)# mgc h248-timer dml 300 dms 100子卡保存数据，子卡会重启：ZXAN(config-voip)# saveZXAN(config-voip)# exitZXAN(config)# exitZXAN# write9806h配置方法：9806# show cardSlot Shelf Type Port HardVer SoftVer Status----------------------------------------------------------------------2 1 ATLC 48 080100 version no Inservice5 1 SCCB 2 080100 version no Inservice----------------------------------------------------------------------9806# configure9806(config)# add-vlan 30009806(config)# vlan 3000 5/1 tag 设置5号板位以tag方式加入vlan3000语音vlan 9806(config)# ip subnet 10.65.3.22 255.255.255.0 3000 voip 设置窄带静态ip与vlan 9806(config)# ip route 10.0.0.0 255.0.0.0 10.65.3.1 设窄带静态网关和路由配置MGC：根据软交换的IP地址，使用mod-mgc命令修改缺省数据。
中兴OLT组播配置
目前，EPON作为主要的接入技术，在运营商中大量使用，下面以中兴C220/C200（Version V1.1.3P2T6）OLT为例，在EPON网络中配置组播。
网络环境信息如下：用户访问VLAN为100，OLT透传该VLAN，用户网关在上级三层交换机上，组播地址为239.192.0.1，OLT上联千兆端口为gei_0/2/1，ONU连接的PON口为epon-olt_0/11/1，ONU型号为D402，PC/STB连接到ONU的第1端口。
1、配置用户接入VLAN100，连接用户电脑/STB。
vlan 100name STB_PCmulticast-packet drop-unknown2、IGMP相关参数检查。
缺省情况下，IGMP都是起来的，不用额外配置。
igmp enableigmp version-mode v1 acceptigmp version-mode v2 acceptigmp version-mode v3 acceptigmp span-vlan enableigmp snooping-aging-time 300igmp bandwidth-control disableigmp host-tracking disableigmp robustness 2igmp query-interval 125igmp query-max-resp 100igmp last-query-interval 10igmp last-query-count 2igmp v1router-timeout 400igmp unsolicited-report-interval 10igmp non-match-group dropigmp mcm disable3、配置MVLAN。
MVLAN必须配置，且须与上联路由器或三层交换机所配置的VLAN号相同，亦即VLAN 100。
IGMP模式可以是proxy，也可以是snooping，推荐proxy模式，据中兴说工作稳定些。
中兴OLT全局配置流程
中兴OLT全局配置流程中兴C200/c220配置脚本配置流程：1、添加机架、机框、单板2、配置管理和业务VLAN3、配置OLT管理地址，指定路由4、注册、认证ONU5、配置OLT上行口（模式为trunk）6、配置EPON-ONU口（模式为trunk）7、配置ONU下行口（模式为tag及vlanid）8、配置ONU管理地址及网关ZXAN#conf t 进入配置模式1、添加机架、机框、单板ZXAN(config)#add-rack rackno 0 racktype ZXPONZXAN(config)#add-shelf shelfno 0 shelftype ZXA10C200-A （C200)ZXAN(config)#add-shelf shelfno 0 shelftype ZXA10C220-B （C220)ZXAN(config)#add-card slotno 1 EPFC2、创建业务VLAN 1）逐渐创建VLANZXAN(config)#vlan 100 ZXAN(config)#vlan 101 ZXAN(config)#vlan 31 2）批量创建VLANZXAN (config )#vlan databaseZXAN(vlan)#vlan 100，101，31（批量增加VLAN）3、配置OLT管理地址，指定路由ZXAN(config)#Interface vlan 31ZXAN(config-if)ip add 172.16.31.2 255.255.255.0ZXAN(config-if)exitZXAN(config)#ip route 0.0.0.0 0.0.0.0 172.16.31.14、注册、认证ONU 1）注册ONUZXAN(config)#interface epon-olt_0/1/2ZXAN(config-if)#onu 1 type ZTE-F402 mac 000c.0000.0001 （mac地址可以通过ZXAN#show onu unauthentication epon-olt_0/1/2 查看）2）认证ONUZXAN(config)#interface epon-onu_0/1/2:1ZXAN(config-if)#authentication enable5、配置OLT上行口ZXAN(config)#interface gei_0/4/3ZXAN(config-if)#switchport mode trunkZXAN(config-if)#switchport vlan 31，100，101 tag6、配置EPON-ONU口ZXAN(config)#interface epon-onu_0/1/2:1ZXAN(config-if)switchport mode trunkZXAN(config-if)switchport vlan 31，101，100 tag7、配置ONU下行口（数据从OLT下发）ZXAN(config)#pon-onu-mng epon-onu_0/1/2:1ZXAN(epon-onu-mng)#vlan port eth_0/1 mode tag vlan 101 priority 0>进入ONU管理视图>配置ONU的eth_0/1口模式为tag(即access)，属于lan101，优先级为08、配置OLT管理地址，配置ONU管理地址及网关ZXAN(config)#pon-onu-mng epon-onu_0/1/2:1ZXAN(epon-onu-mng)#mgmt-ip onu-ip 172.16.31.3 255.255.255.0 0 31 mgm-Ip 0.0.0.0 0.0.0.0 172.16.31.1 status enable >进入ONU管理视图>配置ONU管理地址及网关（onu管理地址/掩码/优先级0/管理vlan31/网关/status enable）。
C300 EPON 中兴开局初学者配置手册最新
1、一个新的OLT了首先第一步就是配置单板，卡槽，机框等信息ZXAN(config)#add-rack rackno 1 racktype IEC19ZXAN(config)#add-shelf rackno 1 shelfno 1 shelftype IEC_SHELFZXAN(config)#add-card rackno 1 shelfno 1 slotno 0 PRWGZXAN(config)#add-card rackno 1 shelfno 1 slotno 1 PRWGZXAN(config)#add-card rackno 1 shelfno 1 slotno 2 ETGOZXAN(config)#add-card rackno 1 shelfno 1 slotno 3 GTGOZXAN(config)#add-card rackno 1 shelfno 1 slotno 19 GUFQ查看卡槽信息ZXAN(config)#show cardRack Shelf Slot CfgType RealType Port HardV er SoftV er Status-------------------------------------------------------------------------------1 1 0 PRWG PRWG 0 INSERVICE 1 1 1 PRWG PRWG 0 NOPOWER 1 12 ETGO ETGOD 8 091201 V1.2.3P3 INSERVICE 1 1 3 GTGO GTGOA 8 080802 V1.2.3P3 INSERVICE 1 1 10 SCXM SCXM 0 090700 V1.2.3P3 STANDBY 1 1 11 SCXM SCXM 0 090700 V1.2.3P3 INSERVICE 1 1 19 GUFQ GUFQ4 090200 V1.2.3P3 INSERVICEZXAN(config)#show running-configadd-rack rackno 1 racktype IEC19add-shelf rackno 1 shelfno 1 shelftype IEC_SHELFadd-card rackno 1 shelfno 1 slotno 0 PRWGadd-card rackno 1 shelfno 1 slotno 1 PRWGadd-card rackno 1 shelfno 1 slotno 2 ETGOadd-card rackno 1 shelfno 1 slotno 3 GTGOadd-card rackno 1 shelfno 1 slotno 19 GUFQadd-card rackno 1 shelfno 1 slotno 20 GUFQ2、创建VLAN 100 200 并配置各vlan的ip地址，以便后期检测链路的正确性ZXAN(config)#vlan databaseZXAN(vlan)#vlan 100ZXAN(config-vlan)#exitZXAN(config)#inter vlan 100ZXAN(config-if)#ip address 192.168.128.232 255.255.255.0ZXAN(config-if)#exitZXAN(config)#vlan 200ZXAN(config-vlan)#exitZXAN(config)#inter vlan 200ZXAN(config-if)#ip address 192.168.200.200 255.255.255.0ZXAN(config-if)#exitZXAN(config)#epononu认证模式只对epon卡槽有效ZXAN(config-epon)#onu-authentication-mode auth-loid-as-sn 1/2 enable3、创建ONU的流量模板ZXAN(config-epon)#onu-sla-profile profile-name create 10MZXAN(config-epon)#onu-sla-profile profile-set 10M upstream assured 5000 maximum 10000 ZXAN(config-epon)#onu-sla-profile profile-set 10M downstream maximum 10000ZXAN(config-epon)#exit4、创建SIP模板ZXAN(config-epon)#sip-profile sip-test register-server ip 192.168.128.70ZXAN(config-epon)#sip-profile sip-test backup-register-server ip 192.168.128.70ZXAN(config-epon)#sip-profile sip-test proxy-server ip 192.168.128.70ZXAN(config-epon)#sip-profile sip-test backup-proxy-server ip 192.168.128.70ZXAN(config-epon)#sip-profile sip-test outbound-server ip 192.168.128.705、创建fax模板ZXAN(config-epon)#fax profile t30 t38 disable control-mode ss6、创建h248模板ZXAN(config-epon)#h248-profile h248-test register-server ip 192.168.128.70 port 5060ZXAN(config-epon)#h248-profile h248-test backup-register-server ip 192.168.128.70 port 5060 ZXAN(config-epon)#h248-profile h248-test mg register-mode ip port 5060ZXAN(config-epon)#h248-profile h248-test heartbeat-mode h248ctc rtp-link-test disable cycle 30 count 37、创建VOIP-IP模板ZXAN(config-epon)#voip-vlan profile voipvlan-test tag-mode tag cvlan 300 priority 78、创建VOIP-VLAN模板ZXAN(config-epon)#voip-ip profile voipip-test relation independent mode static gateway 192.168.128.1 dns 192.168.128.1ZXAN(config)#show running-configeponvoip-ip profile voipip-test relation independent mode static gateway 192.168.128.1 dns 192.168.128.1voip-vlan profile voipvlan-test tag-mode tag cvlan 300 priority 7h248-profile h248-test register-server ip 192.168.128.70 port 5060h248-profile h248-test backup-register-server ip 192.168.128.70 port 5060h248-profile h248-test heartbeat-mode h248ctc rtp-link-test disable cycle 30 count 3h248-profile h248-test mg register-mode ip port 5060sip-profile sip-test register-server ip 192.168.128.70 port 5060sip-profile sip-test backup-register-server ip 192.168.128.70 port 5060sip-profile sip-test proxy-server ip 192.168.128.70 port 5060sip-profile sip-test backup-proxy-server ip 192.168.128.70 port 5060sip-profile sip-test outbound-server ip 192.168.128.70 port 5060sip-profile sip-test register-interval 3600sip-profile sip-test heartbeat enable cycle 20 count 3sip-profile sip-test mg port 5060fax profile t30 t38 disable control-mode ss!重命名ONU-sla名字ZXAN(config-epon)#onu-sla-profile profile-name rename oldname xlxh-onu-dba newname onu-sla-test配置改ONU-type不会自动下发配置ZXAN(config)#eponZXAN(config-epon)#auto-dispatch-set ZTE-EPON disableZXAN(config-epon)#exit9、配置ONU-TYPE如果OLT没有配置ONU-type则需要自己配置ONU-typeZXAN(config)#ponZXAN(config-pon)#onu-type ZTE-EPON epon description 804WZXAN(config-pon)#onu-type-if ZTE-EPON eth_0/1-4ZXAN(config-pon)#show onu-type epon ZTE-EPONOnu type name: ZTE-EPONPon type: eponDescription: 804WProtect type: noneSpeed: 1gZXAN(config-pon)#exit10、配置带宽业务10.1、查询未注册的ONUZXAN(config)#inter epon-olt_1/2/1ZXAN(config-if)#show onu unauthenticationOnu Interface : epon-onu_1/2/1:1Onu Model : RL-4WMAC Address : 1c18.4a0d.d30fSN :LOID :LOID_PSW :Online State : authentication denyExtOam State : completeSoftware Version : 6151Hardware Version : v1.0_01RegTime : 2015/07/22 10:43:06ZXAN(config-if)#exit10.2、注册ONUZXAN(config-if)#onu 1 type ZTE-EPON mac 1c18.4a0d.d30fZXAN(config-if)#show onu detail-info epon-onu_1/2/1:110.3、进入ONU端口下配置业务端口VLANZXAN(config)#inter epon-onu_1/2/1:1ZXAN(config-if)#sla-profile 10MZXAN(config-if)#switchport vlan 200 tagZXAN(config-if)#exit10.4、上行添加ＶＬＡＮZXAN(config)#inter gei_1/19/1ZXAN(config-if)#switchport default vlan 100ZXAN(config-if)#switchport vlan 200 tagZXAN(config)#inter gei_1/19/2ZXAN(config-if)#switchport vlan 200 tagZXAN(config-if)#switchport default vlan 100ZXAN(config-if)#exit10.5、远程ONU下配置用户侧VLAN由于带WiFi的onu带有web管理界面；在web页面上配置vlan相当于untag vlan ZXAN(config)#pon-onu-mng epon-onu_1/2/1:1ZXAN(epon-onu-mng)#vlan port eth_0/1 mode transparentZXAN(epon-onu-mng)#exitZXAN(config)#exit11、保存配置ZXAN#writeZXAN(config)#show runningvlan databasevlan 1,100,200,300!!epononu-authentication-mode auth-loid-as-sn 1/2 enableencrypt algorithm 1/2 triple-churning key-update-period 20 churning-timer 3onu-sla-profile profile-name create onu-sla-testonu-sla-profile profile-set onu-sla-test upstream fixed 0 fixedpkt 64 assured 102400 maximum 1024000maxburst 45000 priority 0onu-sla-profile profile-set onu-sla-test downstream maximum 1024000onu-sla-profile profile-name create 10Monu-sla-profile profile-set 10M upstream fixed 0 fixedpkt 64 assured 5000 maximum 10000 maxburst 45000priority 0onu-sla-profile profile-set 10M downstream maximum 10000auto-dispatch-set ZTE-EPON disable!pononu-type ZTE-EPON epon description 804Wonu-type-if ZTE-EPON eth_0/1onu-type-if ZTE-EPON eth_0/2onu-type-if ZTE-EPON eth_0/3onu-type-if ZTE-EPON eth_0/4uncfg-onu-display-info sn pw!interface vlan 100ip address 192.168.128.232 255.255.255.0!interface vlan 200ip address 192.168.200.200 255.255.255.0!interface vlan 300ip address 192.168.100.100 255.255.255.0!interface null1!interface epon-olt_1/2/1p2p mode grouponu 1 type ZTE-EPON mac 1c18.4a0d.d30f ip-cfg static !interface epon-onu_1/2/1:1admin enablesla-profile 10M vport 1encrypt direction downstream enable vport 1ems-autocfg-request disableswitchport mode hybrid vport 1switchport vlan 100 tag vport 1!!interface gei_1/19/1hybrid-attribute fibernegotiation autoflowcontrol disableport-protect disableuplink-isolate disableswitchport mode hybridswitchport default vlan 100switchport vlan 200 tag!interface gei_1/19/2hybrid-attribute fibernegotiation autoflowcontrol disableport-protect disableuplink-isolate disableswitchport mode hybridswitchport default vlan 100!二、配置不带WIFI的EPON ONU RL804C || 804FC ZXAN(config)#RL804C || 804FCZXAN(config)#show onu unauthenticationOnu Interface : epon-onu_1/2/1:1Onu Model : RL-4FCMAC Address : 1c18.4a0f.e563SN :LOID :LOID_PSW :Online State : authentication denyExtOam State : completeSoftware Version : 6151Hardware Version : v1.0_01RegTime : 2015/07/22 13:44:41ZXAN(config-if)#show running-config inter epon-olt_1/2/1 !interface epon-olt_1/2/1p2p mode grouponu 1 type ZTE-EPON mac 1c18.4a0d.d30f ip-cfg static!ZXAN(config-if)#interface epon-olt_1/2/1ZXAN(config-if)#onu 2 type ZTE-EPON mac 1c18.4a0f.e563ZXAN(config)#inter epon-onu_1/2/1:2ZXAN(config-if)#switchport vlan 100 tagZXAN(config-if)#switchport vlan 200 tagZXAN(config-if)#exitZXAN(config)#pon-onu-mng epon-onu_1/2/1:2ZXAN(epon-onu-mng)#vlan port eth_0/1 mode tag vlan 100 priority 0 ZXAN(epon-onu-mng)#vlan port eth_0/2 mode tag vlan 200 priority 1ZXAN(epon-onu-mng)#show running-configadd-rack rackno 1 racktype IEC19add-shelf rackno 1 shelfno 1 shelftype IEC_SHELFadd-card rackno 1 shelfno 1 slotno 0 PRWGadd-card rackno 1 shelfno 1 slotno 1 PRWGadd-card rackno 1 shelfno 1 slotno 2 ETGOadd-card rackno 1 shelfno 1 slotno 3 GTGOadd-card rackno 1 shelfno 1 slotno 19 GUFQsystem-monitor watchdog rackno 1 shelfno 1 slotno 0 disablesystem-monitor watchdog-duration rackno 1 shelfno 1 slotno 0 value 5 system-monitor endless-loop duration rackno 1 shelfno 1 slotno 0 value 75 system-monitor endless-loop reboot rackno 1 shelfno 1 slotno 0 disable system-monitor task-suspend-reboot rackno 1 shelfno 1 slotno 0 all system-monitor watchdog rackno 1 shelfno 1 slotno 1 disablesystem-monitor watchdog-duration rackno 1 shelfno 1 slotno 1 value 5 system-monitor endless-loop duration rackno 1 shelfno 1 slotno 1 value 75 system-monitor endless-loop reboot rackno 1 shelfno 1 slotno 1 disable system-monitor task-suspend-reboot rackno 1 shelfno 1 slotno 1 all system-monitor watchdog rackno 1 shelfno 1 slotno 2 disablesystem-monitor watchdog-duration rackno 1 shelfno 1 slotno 2 value 5 system-monitor endless-loop duration rackno 1 shelfno 1 slotno 2 value 75 system-monitor endless-loop reboot rackno 1 shelfno 1 slotno 2 disable system-monitor task-suspend-reboot rackno 1 shelfno 1 slotno 2 all system-monitor watchdog rackno 1 shelfno 1 slotno 3 disablesystem-monitor watchdog-duration rackno 1 shelfno 1 slotno 3 value 5 system-monitor endless-loop duration rackno 1 shelfno 1 slotno 3 value 75 system-monitor endless-loop reboot rackno 1 shelfno 1 slotno 3 disable system-monitor task-suspend-reboot rackno 1 shelfno 1 slotno 3 all system-monitor watchdog rackno 1 shelfno 1 slotno 10 enablesystem-monitor watchdog-duration rackno 1 shelfno 1 slotno 10 value 5 system-monitor endless-loop duration rackno 1 shelfno 1 slotno 10 value 75 system-monitor endless-loop reboot rackno 1 shelfno 1 slotno 10 disable system-monitor task-suspend-reboot rackno 1 shelfno 1 slotno 10 all system-monitor watchdog rackno 1 shelfno 1 slotno 11 enablesystem-monitor watchdog-duration rackno 1 shelfno 1 slotno 11 value 5 system-monitor endless-loop duration rackno 1 shelfno 1 slotno 11 value 75 system-monitor endless-loop reboot rackno 1 shelfno 1 slotno 11 disable system-monitor task-suspend-reboot rackno 1 shelfno 1 slotno 11 all system-monitor watchdog rackno 1 shelfno 1 slotno 19 disablesystem-monitor watchdog-duration rackno 1 shelfno 1 slotno 19 value 5system-monitor endless-loop duration rackno 1 shelfno 1 slotno 19 value 75system-monitor endless-loop reboot rackno 1 shelfno 1 slotno 19 disablesystem-monitor task-suspend-reboot rackno 1 shelfno 1 slotno 19 all!vlan databasevlan 1,100,200,300!!epononu-authentication-mode auth-loid-as-sn 1/2 enableencrypt algorithm 1/2 triple-churning key-update-period 20 churning-timer 3onu-sla-profile profile-name create onu-sla-testonu-sla-profile profile-set onu-sla-test upstream fixed 0 fixedpkt 64 assured 102400 maximum 1024000maxburst 45000 priority 0onu-sla-profile profile-set onu-sla-test downstream maximum 1024000onu-sla-profile profile-name create 10Monu-sla-profile profile-set 10M upstream fixed 0 fixedpkt 64 assured 5000 maximum 10000 maxburst 45000priority 0onu-sla-profile profile-set 10M downstream maximum 10000auto-dispatch-set ZTE-EPON disable!!pononu-type ZTE-EPON epon description 804Wonu-type-if ZTE-EPON eth_0/1onu-type-if ZTE-EPON eth_0/2onu-type-if ZTE-EPON eth_0/3onu-type-if ZTE-EPON eth_0/4uncfg-onu-display-info sn pw!interface mng1ip address 136.1.1.100 255.255.255.0boot-server 192.168.110.2boot-username xlxhconfig-filename startrun.datimgfile-location local!interface vlan 100ip address 192.168.128.232 255.255.255.0!interface vlan 200ip address 192.168.200.200 255.255.255.0!interface vlan 300ip address 192.168.100.100 255.255.255.0!interface null1!interface epon-olt_1/2/1p2p mode grouponu 1 type ZTE-EPON mac 1c18.4a0d.d30f ip-cfg static onu 2 type ZTE-EPON mac 1c18.4a0f.e563 ip-cfg static !interface epon-onu_1/2/1:1admin enablesla-profile 10M vport 1encrypt direction downstream enable vport 1ems-autocfg-request disableswitchport mode hybrid vport 1switchport vlan 100,200 tag vport 1!interface epon-onu_1/2/1:2admin enableencrypt direction downstream enable vport 1ems-autocfg-request disableswitchport mode hybrid vport 1switchport vlan 100,200 tag vport 1!interface gei_1/19/1hybrid-attribute fibernegotiation autoflowcontrol disableport-protect disableuplink-isolate disableswitchport mode hybridswitchport default vlan 100switchport vlan 200 tag!interface gei_1/19/2hybrid-attribute fibernegotiation autoflowcontrol disableport-protect disableuplink-isolate disableswitchport mode hybridswitchport default vlan 100switchport vlan 200,300 tag!!!pon-onu-mng epon-onu_1/2/1:1no auto-configvlan port eth_0/1 mode transparent!!pon-onu-mng epon-onu_1/2/1:2no auto-configvlan port eth_0/1 mode tag vlan 100 priority 0vlan port eth_0/2 mode tag vlan 200 priority 1!eponvoip-ip profile voipip-test relation independent mode static gateway 192.168.128.1 dns 192.168.128.1voip-vlan profile voipvlan-test tag-mode tag cvlan 300 priority 7h248-profile h248-test register-server ip 192.168.128.70 port 5060h248-profile h248-test backup-register-server ip 192.168.128.70 port 5060h248-profile h248-test heartbeat-mode h248ctc rtp-link-test disable cycle 30 count 3h248-profile h248-test mg register-mode ip port 5060sip-profile sip-test register-server ip 192.168.128.70 port 5060sip-profile sip-test backup-register-server ip 192.168.128.70 port 5060sip-profile sip-test proxy-server ip 192.168.128.70 port 5060sip-profile sip-test backup-proxy-server ip 192.168.128.70 port 5060sip-profile sip-test outbound-server ip 192.168.128.70 port 5060sip-profile sip-test register-interval 3600sip-profile sip-test heartbeat enable cycle 20 count 3sip-profile sip-test mg port 5060fax profile t30 t38 disable control-mode ss!12、配置RL804系列不带WiFi的vlan业务配置方式一：通过trunk vlan配置，但是起不到端口隔离的作用；ZXAN(epon-onu-mng)#vlan port eth mode hybrid def-vlan 200 vlan-list 100ZXAN(epon-onu-mng)#vlan port eth_0/2 mode trunk vlan-list 100 def-vlan 200三四口的方式配置；起到端口隔离作用；可以配置不同的业务vlanZXAN(epon-onu-mng)#vlan port eth_0/3 mode tag vlan 100 priority 0ZXAN(epon-onu-mng)#vlan port eth_0/4 mode tag vlan 200 priority 013、配置RL804W系列带WiFi的vlan业务配置pon-onu-mng epon-onu_1/2/1:1no auto-configvlan port eth_0/1 mode transparent804W WEB 管理界面配置这样能实现配置两个业务vlan的功能2、如果配置eth1 口为路由DHCP 绑定1 口；可以上网，但是如果eth2 绑定的vlan200 也是Internet route模式；则接入2 口也能ping通eth1 口绑定的vlan1003、如果配置eth1 口为路由DHCP 绑定1 口；可以上网，但是如果eth2 绑定的vlan200 是other 桥模式；则接入2 口不能ping通eth1 口绑定的vlan 100 起到两个业务分配的效果14、中兴对接GPON ONU的配置14.1 配置ONU-type gpononu-type ZTE-EPON epon description 804Wonu-type ZTE-GPON gpon description 1GE+4FE+2POTS onu-type ZTE-GPON gpon max-tcont 8onu-type ZTE-GPON gpon max-gemport 32onu-type ZTE-GPON gpon max-switch-perslot 32onu-type ZTE-GPON gpon max-flow-perswitch 32onu-type ZTE-GPON gpon max-iphost 1onu-type-if ZTE-GPON eth_0/1onu-type-if ZTE-GPON eth_0/2onu-type-if ZTE-GPON eth_0/3onu-type-if ZTE-GPON eth_0/4onu-type-if ZTE-GPON pots_0/1onu-type-if ZTE-GPON pots_0/2uncfg-onu-display-info sn pw配置gpon ONU对接OLT14.2、查询未注册的ONUZXAN(config)#show gpon onu uncfgOnuIndex Sn State---------------------------------------------------------------------gpon-onu_1/3/1:1 GPON12345678 unknown ZXAN(config)#14.2、注册gpon ONUZXAN(config-if)#onu 1 type ZTE-GPON sn?sn Serial number authentication modesn+pw Sn+pw authentication modesn+hpw Sn+hpw authentication modesn+rid sn+rid authentication mode(XGPON)ZXAN(config-if)#onu 1 type ZTE-GPON sn GPON12345678 ?vport-mode Vport configuration mode<cr>ZXAN(config-if)#onu 1 type ZTE-GPON sn GPON12345678.[Successful]ZXAN(config-if)#14.3、配置tcont 带宽模板ZXAN(config)#gponZXAN(config-gpon)#profile ?tcont Configure T-CONT profiletraffic Configure traffic profileZXAN(config-gpon)#profile tcont 100M type ?1 -Fixed bandwidth2 -Assured bandwidth3 -Assured bandwidth and Non-assured bandwidth4 -Best-effort bandwidth5 -The super set of all of T-CONT typesZXAN(config-gpon)#profile tcont 100M type 3 assured 100000 maximum 1024000 [Successful]ZXAN(config-gpon)#14.4、配置ONU-SIP模板ZXAN(config-gpon)#onu profile sip sip-test proxy 192.168.128.7014.5、配置带宽业务端口ZXAN(config)#inter gpon-onu_1/3/1:1ZXAN(config-if)#tcont 1 name tcont1 profile 100MZXAN(config-if)# gemport 1 name gemport1 unicast tcont 1 dir both queue 1 ZXAN(config-if)# service-port 1 user-vlan 300 vlan 10014.6、配置业务通道pon-onu-mng gpon-onu_1/3/1:1service internet type internet gemport 1 vlan 300switchport-bind switch_0/1 veip 1!!14.7、配置用户侧VLAN15、配置gpon-onu的线路模板onu-profile gpon line line-gpontcont 1 name tcont1 profile 100Mtcont 1 gap mode3gemport 1 unicast tcont 1 dir both queue 1!pon!16、配置gpon-onu远程管理模板方式一：pononu-profile gpon remote remote-gponservice date type internet gemport 1 cos 0 vlan 300switchport-bind switch_0/1 veip 1!方式二：pononu-profile gpon remote remote-cvlan300service intenet gemport 1 vlan 300veip 1 inter-domain test1switchport-bind switch_0/1 veip 1vlan-filter-mode veip 1 tag-filter vid-match untag-filter discardvlan-filter veip 1 priority 0 vid 300ex-vlan veip 1 input-tpid 0x8100 output-tpid 0x8100 down-mode inverse-upstream !17、加入已配置的线路模板和远程onu模板（下面即配置带宽业务）ZXAN(config)#inter gpon-olt_1/3/1ZXAN(config-if)#onu 1 profile ?alarm Alarm profileline Line profileperformance Performance profileremote Remote profileZXAN(config-if)#onu 1 profile line line-gponZXAN(config-if)#onu 1 profiler remote remote-gpon17.1 在onu接口下配置业务VLANZXAN(config)#inter gpon-olt_1/3/1：1ZXAN(config-if)# service-port 1 user-vlan 300 vlan 100。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
中兴C200/c220配置脚本
配置流程：
1、添加机架、机框、单板
2、配置管理和业务VLAN
3、配置OLT管理地址，指定路由
4、注册、认证ONU
5、配置OLT上行口（模式为trunk）
6、配置EPON-ONU口（模式为trunk）
7、配置ONU下行口（模式为tag及vlanid）
8、配置ONU管理地址及网关
ZXAN#conf t 进入配置模式
1、添加机架、机框、单板
ZXAN(config)#add-rack rackno 0 racktype ZXPON
ZXAN(config)#add-shelf shelfno 0 shelftype ZXA10C200-A （C200)
ZXAN(config)#add-shelf shelfno 0 shelftype ZXA10C220-B （C220)
ZXAN(config)#add-card slotno 1 EPFC
2、创建业务VLAN 1）逐渐创建VLAN
ZXAN(config)#vlan 100 ZXAN(config)#vlan 101 ZXAN(config)#vlan 31 2）批量创建VLAN
ZXAN (config )#vlan database
ZXAN(vlan)#vlan 100，101，31（批量增加VLAN）
3、配置OLT管理地址，指定路由ZXAN(config)#Interface vlan 31
ZXAN(config-if)ip add 172.16.31.2 255.255.255.0
ZXAN(config-if)exit
ZXAN(config)#ip route 0.0.0.0 0.0.0.0 172.16.31.1
4、注册、认证ONU 1）注册ONU
ZXAN(config)#interface epon-olt_0/1/2
ZXAN(config-if)#onu 1 type ZTE-F402 mac 000c.0000.0001
（mac地址可以通过ZXAN#show onu unauthentication epon-olt_0/1/2 查看）
2）认证ONU
ZXAN(config)#interface epon-onu_0/1/2:1
ZXAN(config-if)#authentication enable
5、配置OLT上行口
ZXAN(config)#interface gei_0/4/3
ZXAN(config-if)#switchport mode trunk
ZXAN(config-if)#switchport vlan 31，100，101 tag
6、配置EPON-ONU口
ZXAN(config)#interface epon-onu_0/1/2:1
ZXAN(config-if)switchport mode trunk
ZXAN(config-if)switchport vlan 31，101，100 tag
7、配置ONU下行口（数据从OLT下发）
ZXAN(config)#pon-onu-mng epon-onu_0/1/2:1
ZXAN(epon-onu-mng)#vlan port eth_0/1 mode tag vlan 101 priority 0
>进入ONU管理视图
>配置ONU的eth_0/1口模式为tag(即access)，属于lan101，优先级为0
8、配置OLT管理地址，配置ONU管理地址及网关
ZXAN(config)#pon-onu-mng epon-onu_0/1/2:1
ZXAN(epon-onu-mng)#mgmt-ip onu-ip 172.16.31.3 255.255.255.0 0 31 mgm-Ip 0.0.0.0 0.0.0.0 172.16.31.1 status enable >进入ONU管理视图
>配置ONU管理地址及网关（onu管理地址/掩码/优先级0/管理vlan31/网关/status enable）。