screw spec-螺丝规格说明书
screw spec-螺丝规格说明书
一、螺丝通用技术条件如无其它规定,则按本公司以下要求:1.外观质量检查:表面镀层/氧化层均匀致密,无露底、脱落、变形、缺口、裂纹和披锋等不良.2.盐雾腐蚀试验: 350C/5%NaCl水溶液/2hrs.3.可针对具体要求, 对样品作扭力装配试验二、分类本公司涉及的螺丝分类如下:2.1PA--圆头尖脚螺丝2.2PB--圆头平脚螺丝2.3PT--圆头介脚螺丝2.4BA—大头尖脚螺丝2.5BT--平脚介脚螺丝2.6KA--平头尖脚螺丝2.7KB--平头平脚螺丝2.8KT--平头介脚螺丝2.9PWA/ WA--带介子尖脚螺丝2.10PWB /WB--带介子平脚螺丝2.11PWT/ WT--带介子介脚螺丝2.12PM--圆头机牙螺丝2.13KM--平头平脚机牙螺丝2.14六角机牙螺丝代号说明: A-尖脚; B-大头,平脚; M-机牙; K-平头; P-圆头; T-介脚; W-带介子.电镀种类蓝锌白锌五彩镀红铜镀黄铜黑锌+防锈油黑锌+Lacquer涂装镀镍镀锡镀铬镀古铜不锈钢清洗■基本头型P 头 B 头V 头喇叭头R 头T 头O 头H 头C 头 F 头I 头IP 头■基本槽型十字槽十一槽一字槽梅花槽内六角槽米字槽精密机械牙小螺丝*种类1.精密小螺丝 ( 1.4 <= d <2.6 )2.特殊极微小螺丝 ( d < 1.4 ).*头型*螺丝公差2.1 PA--圆头尖脚螺丝实物图片结构示意图2.2PB--圆头平脚螺丝2.3 PT--圆头介脚螺丝2.4 BA—大头尖脚螺丝2.5 BT—大头介脚螺丝2.6 KA—平头尖脚螺丝2.7 KB--平头平脚螺丝2.8 KT----平头介脚螺丝2.9 WA--带介子尖脚螺丝2.10 WB/PWB--带介子平脚螺丝2.11 WT/PWT---带介子介脚螺丝2.12 PM--圆头机牙螺丝2.13 KM--平头机牙螺丝2.14六角机牙螺丝PA--圆头尖脚螺丝PB--圆头平脚螺丝PT--圆头介脚螺丝BA—大头尖脚螺丝BT--平脚介脚螺丝KA--平头尖脚螺丝KB--平头平脚螺丝KT--平头介脚螺丝PWA/ WA--带介子尖脚螺丝P WB/WB--带介子平脚螺丝PWT/ WT--带介子介脚螺丝PM--圆头机牙螺丝KM--平头平脚机牙螺丝。
螺丝详解说明书
ψ3.7
24-3082-9001
unit: mm
unit: mm
Remark 鍍鎳 黑色 鍍鎳 鍍鎳 鍍鎳 黑色 黑色 黑色
8
ψ2.6
ψ2
4
1.6
9
ψ2.6
ψ2
5
1.3
10
ψ2.6
ψ1.8
6
1.6
11
ψ2.6
ψ1.8
8
1.6
12
ψ2.6
ψ1.8
8
1.6
13
ψ2.6
ψ1.8
6
1.6
14
ψ2.6
ψ2
10
鍍鎳
3.8
黑色/鍍
1.5
24-0005-9001/9005
鎳
3.3
1.2
24-0022-9001
黑色
3.2
1.2
24-3051-9001
黑色
3.6
1.4
24-3109-9001
黑色
3.8
1.4
24-3001-9005
鍍鋅
5.2
2
24-0026-9005
鍍鎳
5.2
2
24-0096-9005
鍍鎳
5.3
2.2
24-3009-9005
鍍鎳
5.7
鍍白鋅
2
24-3007-9005
(鍍鎳)
7
鍍鎳(白
2.3
24-0099-9005
鋅)
6.5
黑色/鍍
2.4
24-0083-9001/9005
鎳
6.5
2.4
24-0070-9001
黑色
6.7
钻尾螺丝使用说明书
#6,8,10 #12,14
批 规 格 2号批 3号批
- 10 -
② 批的硬度 节省十字批的使用成本，建议使用以下产品中的 X 或H标识产品。
标识 X H G E S
硬度
特征、用途
最高硬度
自钻螺丝以及自攻螺丝、干壁钉螺丝 用 耐磨性能好， 建议用于低扭矩连发螺丝
高硬度
自攻螺丝等中硬度的螺丝 适用中扭矩，建议用于单发螺丝
标准自攻自钻螺丝 (全
标准自攻自钻螺丝 (半牙型)
引导型(PL 自攻自钻螺丝
带翼 自攻自钻螺
- 自攻自钻螺丝的品质
拥有坚固的结合力和长效的耐久性。 代表性的性能数据(并非保证值)如下。
1) 抗拔力 ① 木材的抗拔力 螺丝比螺钉有着高出4~5倍的抗拔力.
-8-
② 铁板的抗拔力(Pull-Out Test)
牙峰高，螺距宽，与木材的结合力和抗拔力强。
两翼防止组合件起翘， 容易使碎屑排出。 两翼在穿过下钢板时自动碎掉。
薄铁板用 标准厚度用
厚板用
引导杆（PL）长度超过结合材料的厚度， 在螺纹攻到上钢板之前钻尾已穿过下钢板， 防止结合物起翘。
用于尖尾无法稳定贯通的薄板(1.0~1.2mm) 的连接, 比标准型有着更强的结合力。
自攻自钻螺丝的材料为低碳素钢(JIS G 3539 SWCH材以及以其相当的材料)和
马式体系不锈钢材(JIS G 4315의 410 以及以其相当的材料). 部分也使用奥式 体系不锈钢材(JIS G 4351 的 SUS304 , XM-7等)
- 自攻自钻螺丝的使用方法
1) 适用的铁板厚度
① 标准型自攻自钻螺丝(带翼，引导杆 产品以外) 铁板和铁板的固定
正确的使用方法(引导杆的应用)
法国螺钉标准(NF screw standards)
编号中文名称英文名称NF B51-128-1993纤维板.螺钉轴向抽出阻力的测定(FIBREBOARDS. DETERMINATION OF RESISTANCE TO AXIAL WITHDRAWAL OF SCREWS. (EUROPEAN STANDARD EN 320).)NF B51-260-1972木屑板.螺丝拔除试验(PARTICLE BOARD. TEST FOR WITHDRAWAL OF SCREWS.)NF C20-115-1971标定截面不超过2.5mm**2，线芯无特殊预加工的硬铜导线连接的无螺钉接线端(TERMINALS WITHOUT SCREW CLAMPING FOR CONNECTION OFCONDUCTORS FOR FIXED WIRING,WITH A NOMINAL CROSS-SECTIONNOT EXCEEDIND 2,5 MM2, AND WITHOUT SPECIAL PREPARATION OFTHE CONDUCTOR)NF C20-116-1981室外铜导线用螺钉丝端子(Terminals with screw campling for external copper conductors.)NF C60-002-1994家用及类似用低压电路用连接装置.第2-2部分:不带螺钉型夹件的分开的部件连接装置的特别要求(Connecting devices for low voltage circuits for householdand similar purposes. Part 2-2 : particular requirementsfor connecting devices as separate entities with screwless-type clamping units)NF C83-403-803-2003详细规范:防松螺钉不可拆卸的厚度为0.8MM的带扁平触点的矩形连接器(Detail Specification : rectangular connectors - Flatcontacts, 0,8 mm thickness, locking screw not detachable.)NF C93-561-1981电子元件.螺钉锁定的小型同轴接头.一般规定(Components for electronic equipment. Miniature coaxialconnectors with screw coupling. General requirements.)NF C93-566-1981电子元件.螺钉锁定射频用同轴接头（ＫＮ系列）.一般规定(ELECTRONIC COMPONENTS. RF COAXIAL CONNECTORS WITH SCREWCOUPLING (TYPE KN). GENERAL REQUIREMENTS.)法国螺钉标准(NF screw standards)NF C93-578-1996射频连接件.第20部分:外导线内径为13.56mm(0,534 in)同时带有两条内导线的屏蔽平衡电缆用双头螺钉(3/4-20统(Radio-frequency connectors. Part 25 : two-pole screw (3/4-20 unef) coupled connectors for use with shielded balancedcables having twin inner conductors with inner diameter ofouter conductor1356mm(0534in)(type twhn))NF E02-312-1981钢制规.螺丝孔莫氏锥环规(STEEL GAUGES. MORSE TAPER RING GAUGES.) NF E02-316-1981钢制规.螺丝孔５％锥度环规(STEEL GAUGES. METRIC TAPER RING GAUGES.)NF E03-152-1981用极限量规检验螺纹.螺钉用螺纹规(Thread checking with limit gauges. Threaded gauges for screw.)NF E03-154-1970公制三角螺纹.用极限规检验螺纹.螺钉和螺钉孔光滑度检查器(THREAD CHECKING WITH LIMIT GAUGES. PLAIN GAUGES FOR SCREWSAND NUTS.)NF E04-012-1-1996技术制图.螺钉和螺纹部件.第1部分:通用规范(Technical drawings. Screw threads and threaded parts. Part1 : general conventions.)NF E04-012-2-1996技术制图.螺钉和螺纹部件.第2部分:螺纹嵌镶件(TECHNICAL DRAWINGS. SCREW THREADS AND THREADED PARTS. PART2 : SCREW THREAD INSERTS. (EUROPEAN STANDARD EN ISO 6410-2).)NF E04-012-3-1996技术制图.螺钉和螺纹部件.第3部分:简化表示(TECHNICAL DRAWINGS. SCREW THREADS AND THREADS AND THREADEDPARTS. PART 3 : SIMPLIFIED REPRESENTATION. (EUROPEANSTANDARD EN ISO 6410-3).)NF E22-201-1992滚珠螺钉.第1部分:词汇和命名(Ball screws. Part 1 : vocabulary and designation.)NF E22-202-1992滚珠螺钉.第2部分:公称直径和公称引线.米制系列(Ball screws. Part 2 : nominal diameters and nominal leads.Metric series.)NF E22-203-1993球端螺钉.第3部分:合格条件和合格试验(Ball screws. Part 3 : acceptance conditions and acceptance tests.)NF E25-011-1992紧固件的机械特性.由非亚铁金属制造的螺栓,螺钉,柱螺栓和螺母(MECHANICAL PROPERTIES OF FASTENERS. BOLTS, SCREWS, STUDSAND NUTS MADE OF NON-FERROUS METALS. (EUROPEAN STANDARD EN28839).)NF E25-018-2-1994沉头螺钉.第2部分:十字槽(CONTERSUNK FLAT HEAD SCREWS. PART 2 : PENETRATION DEPTHY OF CROSS RECESSES. (EUROPEAN STANDARD EN ISO 7721-2).)NF E25-021-1994螺钉的十字槽(欧洲标准EN ISO 4757)(Cross recesses for screws.)NF E25-022-1-2001紧固件公差.螺栓、螺钉、双头螺栓和螺母.第1部分:产品等级A、B及C(Tolerances for fasteners - Bolts, screws, studs and nuts -Part 1 : product grades A, B and C.)NF E25-022-1987紧固件.Ｆ级螺钉和螺帽公差（精密机械）.螺纹直径1到3mm(FASTENERS. TOLERANCES FOR BOLTS,SCREWS AND NUTS PRODUCTGRADE F (FINE MECHANIC). THREAD DIAMETERS FROM 1 UP TO 3MM.)NF E25-023-1992紧固件.螺栓和螺钉的自由尺寸孔(Fasteners. Clearance hole for bolts and screws.)NF E25-100-1-1999碳钢合金制成的紧固件的机械性能.第1部分:螺栓、螺钉和螺柱(Mechanical properties of fasteners made of carbon steeland alloy steel - Part 1 : bolts, screws and studs.)NF E25-100-3-1992紧固件.表面不连续性.第1部分:一般要求的螺栓、螺钉和螺柱(FASTENERS. SURFACE DISCONTINUITIES. PART 1 : BOLTS, SCREWSAND STUDS FOR GENERAL REQUIREMENTS. (EUROPEAN STANDARD EN26157-1).)NF E25-100-4-1992紧固件.表面不连续性.第3部分:特殊要求的螺栓、螺钉和螺柱(FASTENERS. SURFACE DISCONTINUTIES. PART 3 : BOLTS, SCREWAND STUDS FOR SPECIAL REQUIREMENTS. (EUROPEAN STANDARD EN26157-3).)NF E25-100-5-1998碳钢和不锈钢制紧固件的机械性能.第5部分:不处在拉伸应力下的固定螺钉和类似螺纹紧固件(Mechanical properties of fasteners made of carbon steeland alloy steel. Part 5 : set screws and similar threadedfasteners not under tensile stresses.)NF E25-100-6-1998不锈钢紧固件耐腐蚀的机械特性.螺栓,螺丝和双端螺栓(Mechanical properties of corrosion-resistant stainless-steel fasteners. Part 1 : bolts, screws and studs.)NF E25-100-7-1995紧固件的机械性能.第7部分:公称直径1-10mm的螺栓和螺钉的扭力试验和最小扭矩(MECHANICAL PROPERTIES OF FASTENERS. PART 7 : TORSIONALTEST AND MINIMUM TORQUES FOR BOLTS AND SCREWS WITH NOMINALDIAMETERS 1 MM TO 10 MM. (EUROPEAN STANDARD EN 20898-7).)NF E25-100-8-1998不锈钢紧固件耐腐蚀的机械特性.不低于拉伸应力下配套螺钉和类似紧固件(Mechanical properties of corrosion-resistant stainless-steel fasteners. Part 3 : set screws and similar fastenersnot under tensile stress.)NF E25-107-1983金属用螺钉.内部六叶埋头.Ａ级.符号ＦＸ(SCREWS. SIX LOBES RECESSED CONTERSUNK HEAD. PRODUCT GRADE A. SYMBOL FX.)NF E25-108-2001半埋头内六角螺钉(Hexalobular socket raised countersunk head screws.) NF E25-109-2001平头内六角螺钉(Hexalobular socket pan head screws.)NF E25-110-2001圆柱头内六角螺钉(Hexalobular socket head cap screws.)NF E25-111-2001凸头内六角螺钉(Hexalobular socket cheese head screws.)NF E25-114-2001六角头螺钉.产品等级A和B(Hexagon head bolts - Product grades A and B.)NF E25-115-2-2001六角头螺钉.产品等级C(Hexagon head screws - Product grade C.)NF E25-116-1983金属用螺钉.方头.标准杆.A和B级.符号Q(Square head screws. Product grades A and B. Symbol Q.) NF E25-117-1983金属用螺钉.方头.全螺纹.A和B级.符号Q(Square head screws. Product grades A and B. Symbol Q.) NF E25-118-1983金属用螺钉.方头.C级.符号Q(Square head screws. Product grade C. Symbol Q.)NF E25-119-1-1994带有H型或Z型的十字槽沉头螺钉(普通头型).产品等级A.第1部分:性能类别4.8的钢(Countersunk flat head screws (common head style) with typeH or type Z cross recessed. Product grade A. Part 1 : steelof property class 4.8.)NF E25-119-2-1994十字槽沉头螺钉(一般头形).等级A.第2部分:8.8类特性钢,不锈钢和有色金属(Cross recessed countersunk flat head scews (common headstyle). Grade A. Part 2 : steel of property class 8.8,stainless steel and non-ferrous metals.)NF E25-120-1994带有H型或Z型的十字槽半沉头螺钉(普通头型).产品等级A(Countersunk raised head screws (common head style) withtype H or type Z cross recessed. Product grade A.)NF E25-121-1994带有H型或Z型十字槽的平圆头螺钉.产品等级A(Pan head screws with type H or type Z cross recess.Product grade A.)NF E25-122-1984金属用螺钉.称作“POLIER“的Z十字槽宽圆头.A级.符号RLZ(SCREWS. CROSS RECESSED MUSHROOM HEAD (POELIERS). PRODUCTGRADE A. SYMBOL RL Z.)NF E25-123-1994一字槽沉头螺钉(普通头型).产品等级A (Slotted countersunk flat head screws (common head style). Product grade A.)NF E25-124-1994一字槽半沉头螺钉(普通头型).产品等级A (Slotted raised countersunk head screws (common head style). Product grade A.)NF E25-126-1997内六角圆头螺钉(HEXAGON SOCKET BUTTON HEAD SCREWS. (EUROPEAN STANDARD EN ISO 7380).)NF E25-128-1994一字槽平圆头螺钉.产品等级A(Slotted pan head screws. Product grade A.)NF E25-130-1986加垫圈的金属用螺钉.锥形光滑压紧垫圈.Ａ级(SCREWS WITH CONICAL SPRING TIGHTENING WASHER. PRODUCTGRADE A.)NF E25-131-1986加垫圈的金属用螺钉.内齿锥形垫圈.Ａ级(SCREWS WITH CONICAL SPRING INTERNAL TOOTHED TIGHTENING WASHER. PRODUCT GRADE A.)NF E25-132-1986加垫圈的金属用螺钉.外齿垫圈.Ａ级(SCREWS WITH SERRATED EXTERNAL OVERLAPED TOOTHED LOCK TIGHTENNING WASHER. PRODUCT GRADE A.)NF E25-133-1987紧固件.螺杆千斤顶用的金属螺钉.短六角头长制动端螺钉.Ａ和Ｂ级.符号ＨＺ(Fasteners. Screws for screw-jacks. Small hexagon headscrews with long dog point. Product grades A and B. SymbolHZ.)NF E25-134-1987紧固件.螺杆千斤顶用的金属螺钉.短方头短制动端螺钉.Ａ和Ｂ级.符号ＱＺ(Fasteners. Screws for screw-jacks. Small square headscrews with short dog point. Product grades A and B. SymbolQZ.)NF E25-139-1987紧固件.金属用螺钉.Ｚ十字槽宽凸圆柱形头.Ａ级.符号ＣＢＬＺＳ(FASTENERS. SCREWS. Z CROSS RECESSED AND SLOTTED PAN HEAD.GRADE A. SYMBOL CBL ZS.)NF E25-142-1991紧固件.电阻焊金属螺钉.缩小头(FASTENERS. RESISTANCE WELDING SCREWS. REDUCED HEAD. SYMBOL Z. SR.)NF E25-149-1998十字槽圆头螺钉(CROSS RECESSED CHEESE HEAD SCREWS. (EUROPEAN STANDARD EN ISO 7048).)NF E25-150-1998带平垫圈的螺钉和垫圈组件.垫圈强度等级为200 HV和300 HV.(Screw and washer assemblies with plain washers. Washerhardness classes 200 HV and 300 HV.)NF E25-151-2001米制细牙螺纹的六角头螺钉.产品等级A和B (Hexagon head screws with metric fine pitch thread -Product grades A and B.)NF E25-160-1992平端开槽调整螺钉(SLOTTED SET SCEWS WITH FLAT POINT. (EUROPEAN STANDARD EN 24766).)NF E25-161-1992锥端开槽调整螺钉(SLOTTED SET SCEWS WITH CONE POINT. (EUROPEAN STANDARD EN 27434).)NF E25-162-1992长制动端开槽调整螺钉(SLOTTED SET SCREWS WITH LONG DOG POINT. (EUROPEAN STANDARD EN 27435).)NF E25-163-1992蝶形端开槽调整螺钉(SLOTTED SET SCEWS WITH CUP POINT. (EUROPEAN STANDARD EN 27436).)NF E25-501-2000紧固件公差.第3部分:螺栓、螺钉和螺母用平垫圈.A级和C级(Tolerances for fasteners - Part 3 : plain washers forbolts, screws and nuts - Product grades A and C.)NF E25-520-1998螺丝和洗衣机组件用水平式洗衣机.小型,常规型和大型系列.A级产品(PLAIN WASHERS FOR SCREW AND WASHER ASSEMBLIES. SMALL,NORMAL AND LARGE SERIES. PRODUCT GRADE A. (EUROPEANSTANDARD EN ISO 10673).)NF E25-525-2000通用米制螺栓、螺钉和螺母用平垫圈.一般示意图(Plain washers for metric bolts, screws and nuts forgeneral purposes - General plan.)NF E25-600-1984紧固件.木螺钉系列标准(FASTENERS. WOOD SCREWS FAMILY STANDARD.)NF E25-601-1984十字槽沉头木螺钉.符号FZ(CROSS RECESSED COUNTERSUNK HEAD WOOD SCREWS. SYMBOL FZ.)NF E25-602-1984十字槽沉头木螺钉.符号FBZ (CROSS RECESSED RAISED COUNTERSUNK HEAD WOOD SCREWS. SYMBOL FBZ.)NF E25-603-1984一字槽圆头木螺钉.符号RZ(CROSS RECESSED ROUND HEAD WOOD SCREWS. SYMBOL RZ.)NF E25-604-1984有槽沉头木螺钉.符号FS(Slotted countersunk head wood screws. Symbol FS.)NF E25-605-1984木螺丝.一字槽沉头.FBS符号(Slotted raised countersunk head wood screws. Symbol FBS.) NF E25-609-1985木螺钉.螺丝眼(WOODSCREWS. SCREW-EYES.)NF E25-609-1985木螺钉.螺丝眼(WOODSCREWS. SCREW-EYES.)NF E25-610-1985木螺钉.螺丝钩(WOODSCREWS. SCREW-HOOKS.)NF E25-610-1985木螺钉.螺丝钩(WOODSCREWS. SCREW-HOOKS.)NF E25-611-1985木螺钉.直角弯头螺丝钩(WOODSCREWS. SQUARE BEND SCREW HOOKS.)NF E25-611-1985木螺钉.直角弯头螺丝钩(WOODSCREWS. SQUARE BEND SCREW HOOKS.)NF E25-650-1-1994热处理钢自攻螺钉.机械性能(Heat-treated steel tapping screws. Mechanical properties.) NF E25-650-2-1999自攻螺钉螺纹(Tapping screw thread.)NF E25-651-2003耐腐蚀不锈钢紧固件的机械特性.第4部分:攻丝螺钉(Mechanical properties of corrosion-resistant stainlesssteel fasteners - Part 4 : tapping screws.)NF E25-652-2001沉头内六角攻丝螺钉(Hexalobular socket countersunk head tapping screws.)NF E25-653-2001半埋头(椭圆形)内六角攻丝螺钉(Hexalobular socket raised countersunk (oval) head tapping screws.)NF E25-654-2001平头内六角攻丝螺钉(Hexalobular socket pan head tapping screws.)NF E25-655-1983内六角圆头自攻螺钉.符号RLX (ROUND HEAD TAPPING SCREWS WITH SIX LOBES RECESS. SYMBOL RLX .)NF E25-656-1994十字槽沉头自攻螺钉(普通头型)(Cross recessed countersunk (flat) head tapping screws (common head style).)NF E25-657-1994十字槽半沉头椭圆头自攻螺钉(Cross recessed raised countersunk (oval) head tapping screws.)NF E25-658-1994十字槽平圆头自攻螺钉(Cross recessed pan head tapping screws.)NF E25-659-1984自攻螺钉.十字槽半沉头.(`Poelier`).符号RLZ(TAPPING SCREWS. CROSS RECESSED MUSHROOM HEAD (“POELIER“). SYMBOL RL Z.)NF E25-664-1986一字槽六角头自攻螺钉.符号HS(HEXAGON SLOTTED HEAD TAPPING SCREWS. SYMBOL HS.)NF E25-666-1987紧固件.自攻螺钉.Z形十字槽和一字槽平圆头螺钉.符号CBL ZS(FASTENERS. TAPPING SCREWS. Z CROSS RECESSED AND SLOTTEDPAN HEAD. SYMBOL CBL ZS.)NF E25-755-1997非硬度钢和奥斯特不锈钢的内螺纹平行螺钉(Parallel pins with internal thread, of unhardened steel and austenitic stainless steel.)NF E25-756-1997金属不锈钢和硬化钢的平行螺钉(Parallel pins, of hardened steel and martensitic stainless steel (Dowel pins).)NF E25-757-1997非硬度钢和奥斯特不锈钢的内螺纹平行螺钉(Parallel pins with internal thread, of hardened steel and martensitic stainless steel.)NF E25-800-1-1994紧固件.波纹钢管用螺栓.第1部分:带法兰或不带法兰,带尖或不带尖的六角头螺钉.产品等级A(FASTENERS. BOLTS FOR CORRUGATED STEEL PIPES. PART 1 :HEXAGON HEAD SCREWS WITH OR WITHOUT FLANGE, WITH OR WITHOUTNIBS. PRODUCT GRADE A.)NF E25-800-2-1994紧固件.波纹钢管用螺栓.第2部分:带尖或不带尖的圆头螺钉.产品等级A(FASTENERS. BOLTS FOR CORRUGATED STEEL PIPES. PART 2 :CHEESE HEAD SCREWS, WITH OR WITHOUT NIBS. PRODUCT GRADE A.)NF E25-851-1987紧固件.滚制螺钉(ISO米制螺纹).特性(FASTENERS. THREAD ROLLING SCREWS (ISO METRIC THREAD). PROPERTIES.)NF E27-163-1972调整螺钉(ADJUSTING SCREW.)NF E27-164-1976锁紧螺钉的垫板(LOCKING SCREW.)NF E27-165-1976锁紧螺钉的穿销(SLIDE FOR LOCKING SCREW.)NF E27-166-1976滚花头锁紧螺钉(LOCKING SCREW WITH KNURLED KNOB.)NF E27-167-1976星形手扭锁紧螺钉(LOCKING SCREW WITH PALM KNOB.)NF E27-168-1976四翼锁紧螺钉(LOCKING SCREW WITH 4 ARMED KNOB.)NF E27-170-1974通用滚花头螺钉(GENERAL PURPOSE KNURLED THUMBS SCREWS.) NF E27-191-1983紧固件.有肩固定螺钉(FASTENERS. SHOULDERED RETAINING SCREWS.)NF E27-214-1976带小提琴紧弦用的蝶形螺母锁紧螺钉(LOCKING SCREW WITH VIOLIN TYPE THUMB NUT.) NF E27-215-1976带六角螺母的锁紧螺钉(LOCKING SCREWS WITH HEXAGON NUT.)NF E27-303-1968有孔球头螺钉(SPHERICAL HOLED HEAD SCREW.)NF E27-853-1989通用金属卡箍.带型，无螺钉，不可重复使用(Metallic hose clamps for general purpose. Band type,without screws, non re-usable. Specifications.)NF E27-854-1982通用金属卡箍.带型,无螺钉,可重复使用的销钉卡箍或轴的卡箍(METAL-HOSE CLAMPS FOR GENERAL PURPOSES ; BAND TYPE,WITHOUTSCREWS,RE-USABLE,PIN OR AXLE CLAMPS.)NF E62-307-1977机床构造标准部件.多轴头.防护装置.２８和３６卧式防护装置.支架.行程止推螺钉(MODULAR UNITS FOR MACHINE TOOL CONSTRUCTION. MULTI-SPINDLEHEADS. HORIZONTAL TEMPLATES 28 AND 36. SUPPORTS : STOPSCREW.)NF E62-519-2003柱形扁柄刀具用螺钉压紧刀具夹(立铣刀刀夹).第1部分:刀柄驱动系统的尺寸(Tool chucks (end mill holders) wirth clamp screws forflatted cylindrical shank tool - Part 1 : dimensions of thedriving system of tool shanks.)NF E62-520-2003柱形扁柄刀具用螺钉压紧刀具夹(立铣刀刀夹).带7/24锥柄的夹头尺寸(Tools chucks (end mill holders) wirth clamp screws forflatted cylindrical shank tools - Dimensions of chucks with7/24 taper shank.)NF E62-526-2003带7/24外圆锥和莫氏内圆锥缩径套筒和连接螺钉(Reduction sleeves with 7/24 external and Morse internaltaper and incorporated screw.)NF E63-512-1983铸型和挤压器材.金属模型构件.止动螺钉(MOULDING AND EXTRUSION EQUIPMENT. METALLIC MOULDING ELEMENTS. LOCKING SCREWS.)NF E66-103-1993机用螺丝锥和手动螺丝锥(Short machine taps and hand taps.)NF E66-107-2000公称直径由M3-M10的长杆螺丝攻.由回缩的全直径杆型螺丝攻(Long shank taps with nominal diameters from M3 to M10 -Full-diameter shank taps with recess.)NF E66-108-2000公称直径由M3-M24和1/8-1 英寸的长杆螺丝攻.渐减型螺丝攻(Long shank taps with nominal diameters from M3 to M24 and1/8 in to 1 in - Reduced shank taps.)NF E66-120-1975圆柱和锥形管螺纹手用螺丝锥(HAND TAPS FOR PIPE THREADS FOR PARALLEL AND TAPER THREADS.)NF E66-150-1990ＩＳＯ公制螺纹的手用和机用圆螺丝板牙(Hand- An machine-operated circular screwing dies and hand-operated die stocks.)NF E66-153-1990煤气管道圆柱螺纹手用和机用圆螺丝板牙(Hand-and machine-operated circular screwing dies for parallel pipe threads. G series.)NF E74-303-2001螺钉和螺母组装工具.锻造的和管形套筒扳手.头部外形最大尺寸(Assembly tools for screws and nuts - Forged and tubularsocket wrenches - Maximum outside head dimensions.)NF E74-304-2001螺钉和螺母装配工具.双头开口扳手、双头环形扳手和多用扳手.端部最大宽度(Assembly tools for screws and nuts - Double-headed open-ended wrenches, double-headed ring wrenches and combinationwrenches - Maximum widths of heads.)NF E74-305-2001螺钉和螺母装配工具.双头扳手.尺寸选配(Assembly tools for screws and nuts - Double-ended wrenches - Size pairings.)NF E74-307-2001螺钉和螺母用装配工具.组合扳手.扳手长度和端口最大厚度(Assembly tools for screws and nuts - Combination wrenches- Lengths of wrenches and maximum thickness of heads.)NF E74-310-2001螺钉和螺母用装配工具.工程用双头开口扳手.扳手长度和端口厚度(Assembly tools for screws and nuts - Double-headed open-ended engineers' wrenches - Length of wrenches andthickness of the heads.)NF E74-311-2001螺钉和螺母用装配工具.双头平直套筒扳手和斜口套筒扳手.扳手长度和端口厚度(Assembly tools for screws and nuts - Double-headed, flatand offset, box wrenches - Length of wrenches and thicknessof the heads.)NF E74-313-2001螺钉和螺母用装配工具.双头深斜口套筒扳手和改进的斜口套筒扳手.扳手长度和端口厚度(Assembly tools for screws and nuts - Double-headed, deepoffset and modified offset, box wrenches - Length ofwrenches and thickness of the heads.)NF E74-321-1998螺钉和螺母用装配工具.十字形套筒扳手.尺寸和扭矩试验(ASSEMBLY TOOLS FOR SCREWS AND NUTS. FOUR-WAY SOCKETWRENCHES. DIMENSIONS AND TORQUE TEST.)NF E74-322-1972螺钉螺帽紧固工具.齿条式扳手(ASSEMBLY TOOLS FOR SCREWS AND NUTS.RACK WRENCHES.)NF E74-323-1972螺钉螺帽紧固工具.开槽螺帽用单钩扳手(ASSEMBLY TOOLS FOR SCREWS AND NUTS.HOOK WRENCHES)NF E74-324-2001螺钉和螺母用装配工具.可调扳手(Assembly tools for screws and nuts - Adjustable wrenches.)NF E74-325-2003螺钉和螺母用装配工具.手动转矩工具.设计一致性试验、质量一致性试验和重新校准程序的要求和试验方法(Assembly tools for screws and nuts - Hand torque tools -Requirements and test methods for design conformancetesting, quality conformance testing and recalibrationprocedure)NF E74-331-2003螺钉和螺母用装配工具.内六角扳手(Assembly tools for screws and nuts - Hexagon socket screw keys.)NF E74-351-2002螺钉和螺母用装配工具.一字槽头螺钉用旋具.第2部分:手工操作旋具的一般要求、刀刃长度和标记(Assembly tools for screws and nuts - Screwdrivers forslotted-head screws - Part 2 : general requirements,lengths of blades and marking of hand-operatedscrewdrivers)NF E74-352-1998螺钉和螺母用装配工具.槽螺钉用旋具.第1部分:手工及机械操作用的旋具头(Assembly tools for screws and nuts. Screwdrivers forslotted-head screws. Part 1 : tips for hand- and machine-operated screwdrivers.)NF E74-353-1-2002螺钉和螺母用装配工具.机动旋转头.第1部分:一字槽螺钉旋具(Assembly tools for screws and nuts - Machine-operatedscrewdriver bits - Part 1 : screwdriver bits for slottedhead screws.)NF E74-353-2-2002螺钉和螺母用装配工具.机动旋转头.第2部分:十字槽螺钉旋具头(Assembly tools for screws and nuts - Machine-operatedscrewdrivers bits - Part 2 : screwdriver bits for cross-recessed head screws.)NF E74-353-3-2002螺钉和螺母用装配工具.机动旋转头.第3部分:内六角螺钉用旋具头(Assembly tools for screws and nuts - Machine-operatedscrewdriver bits - Part 3 : screwdriver bits for hexagonsocket screws.)NF E74-354-2002螺钉和螺母用装配工具.螺旋棘轮螺钉旋具头.尺寸(Assembly tools for screws and nuts - Spiral ratchetscrewdriver ends - Dimensions.)NF E74-355-1993十字槽头螺钉用旋转具.第1部分:旋具尖(SCREWDRIVERS FOR CROSS-RECESSED HEAD SCREWS. PART 1 : DRIVERS POINTS.)NF E74-356-1993十字槽头螺钉用旋具.第2部分:手持式旋具的一般要求、旋具头长度和标记(SCREWDRIVERS FOR CROSS-RECESSED HEAD SCREWS. PART 2 :GENERAL REQUIREMENTS, LENGTHS OF BLADES AND MARKING OFHAND-OPERATED SCREWDRIVERS.)NF E74-360-2001螺钉和螺母用装配工具.手动和机动螺丝刀的驱动端和连接部件.尺寸和扭矩试验(Assembly tools for screws and nuts - Drive ends for hand-and machine-operated screwdriver bits and connecting parts- Dimensions, torque testing.)NF E74-360-2001螺钉和螺母用装配工具.手动和机动螺丝刀的驱动端和连接部件.尺寸和扭矩试验(Assembly tools for screws and nuts - Drive ends for hand-and machine-operated screwdriver bits and connecting parts- Dimensions, torque testing.)NF E74-361-1997螺钉和螺母用装配工具.方形旋具.第1部分:手动套筒工具用方形旋具(Assembly tools for screws and nuts. Driving squares. Part1 : driving squares for hand socket tools.)NF E74-362-1997螺钉和螺母用装配工具.方形旋具.第2部分:电动套筒工具用方形旋具(Assembly tools for screws and nuts. Driving squares. Part2 : driving squares for power socket tools.)NF E74-363-1-1997螺钉和螺母用装配工具.方形传动套筒.第1部分:手动套筒.尺寸(Assembly tools for screws and nuts. Square drive sockets.Part 1 : hand-operated sockets. Dimensions.)NF E74-363-2-1997螺钉和螺母用装配工具.方形传动套筒.第2部分:机动“冲击“套筒.尺寸(Assembly tools for screws and nuts. Square drive sockets.Part 2 : machine-operated sockets “impact“. Dimensions.)NF E74-363-3-2001螺钉和螺母用组合工具.方形驱动套筒.第3部分:机器驱动套筒(无冲击).尺寸(Assembly tools for screws and nuts - Square drive sockets- Part 3 : machine-operated sockets (“non impact“) -Dimensions.)NF E74-365-1997螺钉和螺母用装配工具.手动方形传动套筒扳手上的传动件.尺寸和试验(Assembly tools for screws and nuts. Driving parts forhand-operated square drive socket wrenches. Dimensions andtests.)NF E74-366-1997螺钉和螺母用装配工具.手动方形传动套筒扳手上的附件.尺寸和试验(Assembly tools for screws and nuts. Attachments for hand-operated square drive socket wrenches. Dimensions andtests.)NF E74-367-1995螺钉和螺母用装配工具.机动插头扳手的方块传动加长六角插头(Assembly tools for screws and nuts. Square drive extensionhexagon insert, for power socket wrenches.)NF E74-381-1997螺钉和螺母用装配工具.技术规范.第1部分:手动扳手和套筒(Assembly tools for screws and nuts. Technicalspecifications. Part 1 : hand-operated wrenches andsockets.)NF E82-020-1984模压锻造零件.拉紧装置用灯的螺钉.规范(DROP FORGINS. EYEBOLTS FOR TURNBUCKLES. REQUIREMENTS.)NF F01-088-1971铁路运输设备.带有槽端头和螺纹端头的未钻孔轴.头部钻孔的螺钉(RAILWAY TRANSPORT EQUIPMENT. UNBORED AXLES WITH SLOTTEDAND THREADED ENDS. SCREWS WITH DRILLED HEADS.)NF F03-004-1983铁路车辆.金属螺钉. 沉头和半沉头. Ａ级.符号Ｆ和ＦＢ(Railway rolling stock. Grade A. Countersunk and raisedcountersunk notched head machine screws. Symbols F and FB.)NF F03-005-1983铁路车辆.金属螺钉. 圆柱头和球面圆柱头.Ａ级. 符号Ｃ和ＣＲ(Railway rolling stock. Grade A. Notched cheese head ornotched dome head machine screws. Symbols C and CR.)NF F03-006-1983铁路车辆.开槽懦半沉头螺钉一螺母. Ａ级.符号ＦＢＰ(Railway rolling stock. Grade A. Slotted or notched raisedcountersunk head screws nuts. Symbol FBP.)NF F03-016-1983铁路车辆.开槽沉头螺钉, 螺母. Ａ级. ＦＰ(Railway rolling stock. Grade A. Slotted countersunk headscrews nuts. Symbol FP.)NF F10-404-1984铁路车辆.0.25MN的联接螺钉(Railway transport equipment. Coupling screw of 0,25 mn.)NF F11-003-1970铁路车辆.手制动. 螺钉和螺母. 螺距和螺纹剖面. 螺钉传动(RAILWAY TRANSPORT EQUIPMENT. HAND BRAKE. SCREWS AND NUTS.PITCHES AND PROFILES. SCREW DRIVES.)NF F50-006-1998铁路固定设备.带可变螺纹的枕木螺丝(Railway fixed equipment. Sleeper screws with variable thread.)NF F55-251-1991铁路固定设备.信号电路.连接和分段器材.螺钉连接部件(RAILWAY FIXED EQUIPMENT. SIGNALLING. CIRCUITS. CONNECTINGAND BREAKING COMPONENTS. SCREW-TYPE TERMINAL BLOCKS.)NF F56-123-1980铁路固定设备.通讯和信号装置架空线路用器材.直径口毫米镀锌方头木螺钉(FIXED RAILWAY INSTALLATIONS. EQUIPMENT FOR OVERHEADTELECOMMUNICATION AND SIGNALLING LINES. GALVANIZED SQUAREHEAD WOOD SCREWS.)NF J41-465-1957造船工业.“金士顿“阀门.螺钉零件(SHIPBUILDING. KINGSTON VALVES. BOLTS AND SCREWS.)NF J46-126-1951造船工业.空气入口.手柄和紧固螺钉(SHIPBUILDING. VENTILATORS. HANDLE AND LOCKING SCREW.) NF L22-063-1970用板手操作的螺母、螺钉和轴的间隙(CLEARANCE FOR WRENCHING NUTS,SCREWS AND PINS.)NF L22-070-1976螺钉的BNAE型十字槽(CROSS RECESS (B.N.A.E.).)NF L22-071-1976NFL ２２-０７０ 型螺钉十字槽用螺丝刀头(SCREW-DRIVER END FOR CROSS RECESS ACCORDING TO NF L 22-070.)NF L22-071-1976NFL ２２-０７０ 型螺钉十字槽用螺丝刀头(SCREW-DRIVER END FOR CROSS RECESS ACCORDING TO NF L 22-070.)NF L22-072-1991航天建筑.螺丝.920型十字槽(Aerospace construction. Bolts and screws. 92 degrees cruciform recess.)NF L22-090-1966修配用大直径标准螺钉、销和垫圈(STANDARDIZED SCREWS,PINS AND WASHERS WITH INCREASED DIAMETER INTENDED FOR REPAIR WORK.)NF L22-111-1975无销孔六角头螺钉.国际单位制螺纹(Hexagon head bolts without split pin hole. Sim thread (rech.).)NF L22-112-1975带销孔六角头螺钉.国际单位制螺纹(Hexagon head bolts with split pin hole. Sim thread (rech.).)NF L22-121-1975带轻杆无锁孔六角头螺钉.国际单位制螺纹(Hexagon head bolts with waisted shank without split pin hole. Sim thread (rech.).)NF L22-122-1975带轻杆有销孔六角头螺钉.国际单位米制螺纹(Hexagon head bolts with waisted shank with split pin hole.Sim thread.)NF L22-125-1985六角头承拉螺钉ISO 螺纹４h 类(Bolt, hexagonal head, for tensile application, . ISO thread 4H class.)NF L22-126-1985带锁紧孔六角头承拉螺钉.ISO螺纹４h 类(Bolt, hexagonal head, with locking hole, for tensile application. ISO thread 4H class.)NF L22-127-1985带颈杆六角头承拉螺钉.ISO螺 纹４h 类(Bolt, hexagonal head, necked shank, for tensile application. ISO thread 4H class.)NF L22-128-1985带颈杆有锁紧孔六角头承拉螺钉.ISO 螺纹４h 类(Bolt, hexagonal head, necked shank, with locking hole, fortensile application. ISO thread 4H class.)NF L22-129-1985带销孔六角头承拉螺钉.ISO 螺纹４h 类(Bolt, hexagonal head, with split pin hole, for tensile application. ISO thread 4H class.)NF L22-134-1975无销孔六角头槽制螺钉.国际单位制螺纹(Precision hexagon head bolts without split pin hole. Sim thread (rech.).)NF L22-135-1975带销孔六角头槽制螺钉.国际单位制螺纹(Precision hexagon head bolts with split pin hole. Sim thread (rech.).)NF L22-136-1984通用六角头螺钉短螺纹(Bolt, hexagonal head, current use, short thread.)NF L22-137-1984带锁紧孔六角头短螺纹螺钉(Bolt, hexagonal head, with locking hole, short thread.) NF L22-138-1984精密六角头短螺纹螺钉(Bolt, hexagonal head, close tolerance, short thread.)NF L22-139-1984带锁紧孔精密头角头短螺纹螺钉(BOLT,HEXAGONAL HEAD,CLOSE TOLERANCE,WITH LOCKING HOLE,SHORT THREAD.)NF L22-140-1984六角头全螺纹螺钉(Bolt, hexagonal head, threaded to head.)NF L22-141-1984有锁紧孔方角头全螺纹螺钉(Bolt, hexagonal head, with locking hole, threaded to head.)NF L22-142-1984常用有销孔六角头螺钉(BOLT,HEXAGONAL HEAD,WITH COTTER PIN HOLE,CURRENT USE.)NF L22-145-1985六角头承拉螺钉.ISO螺纹4G类(Bolt, hexagonal head, for tensile application, ISO thread 4G class.)NF L22-146-1985有锁紧孔六角头承拉螺钉.ISO螺纹4G类(Bolt, hexagonal head, with locking hole, for tensile application. ISO thread 4G class.)NF L22-147-1985带颈杆六角头承拉螺钉.ISO螺纹4G类(Bolt, hexagonal head, necked shank, for tensile application. ISO thread 4G class.)NF L22-148-1985带颈杆有销紧孔六角头承拉螺钉.ISO螺纹4G类(Bolts, hexagonal head, necked shank, with locking hole,for tensile application. ISO thread 4G class.)NF L22-151-1975开槽圆柱头螺钉和紧固凸圆头螺钉.国际单位制螺纹(Slotted and drilled cheese head screws. Sim thread(rech.).)NF L22-152-1975开槽扁头螺钉.国际单位米制螺纹(Slotted mushroom head screws. Sim thread (rech.).)NF L22-153-197590°埋头开槽螺钉.国际单位米制螺纹(Slotted 90 degrees countersunk head screws. Sim thread (rech.).)NF L22-154-1975120°半圆头开槽埋头螺钉.单际单位米制螺纹(Slotted raised 120 degrees countersunk head screws. Simthread (rech.).)NF L22-156-1975锥顶凸圆头开槽螺钉.国际单位米制螺纹(Slotted raised cheese head screws with cone point. Sim thread (rech.).)NF L22-157-1975锥顶扁头开槽螺钉.国际单位米制螺纹(Slotted mushroom head screws with cone point. Sim thread (rech.).)NF L22-158-1975锥顶90°埋头开槽螺钉.国际单位米制螺纹(Slotted 90 degrees countersunk head screws with cone point. Sim thread (rech.).)NF L22-159-1975锥顶120°半圆头开槽埋头螺钉.国际单位米制螺纹(Slotted raised 120 degrees countersunk head screws withcone point. Sim thread (rech.).)NF L22-161-1984有NF L22-72十字槽的通用100°埋头螺钉(Bolt, 100 degrees countersunk head, current use, nf L 22-072 cross recess.)NF L22-162-1984有NF L22-072十字槽的精密100°全螺纹埋头螺钉(Bolt, 100 degrees countersunk head, close tolerance, nf L22-072 cross recess.)NF L22-163-1984有NF L22-072十字槽的常用100°度全螺纹埋头螺钉(Bolt, 100 degrees countersunk head, threaded to head, nf L22-072 cross recess.)NF L22-167-1984有NF L22-070十字槽的常用100°埋头螺钉(Bolt, 100 degrees countersunk head, current use, nf L 22-070 cross recess.)NF L22-168-1984有NF L22-070 十字槽的紧公差100°沉头螺钉(BOLT,100 DEGREES COUNTERSUNK HEAD,CLOSE TOLERANCE,NF L 22-070,CROSS RECESS.)NF L22-169-1984有 NF L22-070十字槽的100°全螺纹埋头螺钉(BOLT,100 DEGREES COUNTERSUNK HEAD,THREADED TO HEAD,NF L22-070,CROSS RECESS.)NF L22-171-1984有NF L22-072十字槽的常用半圆头螺钉(Bolt, pan head, current use, nf L22-072 cross recess.) NF L22-173-1984有NF L22-072十字槽全螺纹半圆头螺钉(BOLT,PAN HEAD,THREADED TO HEAD,NF L 22-072 CROSS RECESS.)NF L22-176-1984有NF L22-072十字槽锥顶半圆头非磁性螺钉(Bolt, pan head, amagnetic with cone point NF L 22-072 cross recess.)NF L22-177-1984有NF L22-070十字槽常用半圆头螺钉(Bolt, pan head, current use, nf L 22-070 cross recess.) NF L22-179-1984有NF L22-070十字槽全螺纹半圆头螺钉(BOLT,PAN HEAD,THREADED TO HEAD,NF L 22-070 CROSS RECESS.)NF L22-181-1976有BNAE十字槽扁头螺钉.国际单位米制螺纹(MUSHROOM HEAD SCREWS WITH B.N.A.E. CROSS RECESS. SIM THREAD.)NF L22-182-1976有BNAE十字槽90°埋头螺钉.国际单位米制螺纹(90 DEGREES COUNTERSUNK HEAD SCREWS WITH B.N.A.E. CROSSRECESS. SIM THREAD.)NF L22-183-1976有BNAE十字槽90°埋头螺钉.国际单位米制螺纹(RAISED 120 DEGREES COUNTERSUNK HEAD SCREWS WITH B.N.A.E.CROSS RECESS. SIM THREAD.)NF L22-184-1976有BNAE十字槽120°埋头螺钉.国际单位米制螺纹(120 DEGREES COUNTERSUNK HEAD SCREWS WITH B.N.A.E. CROSSRECESS. SIM THREAD.)NF L22-186-1976有BNAE十字槽锥顶扁头螺钉.国际单位米制螺纹(MUSHROOM HEAD SCREWS WITH B.N.A.E. CROSS RECESS AND CONEPOINT. SIM THREAD.)NF L22-187-1976有BNAE十字槽锥顶90°埋头螺钉.国际单位米制螺纹(90 DEGREES COUNTERSUNK HEAD SCREWS WITH B.N.A.E. CROSSRECESS AND CONE POINT. SIM THREAD.)NF L22-188-1976有BNAE十字槽锥顶120°埋头半圆头螺钉单国际单位制米螺纹(RAISED 120 DEGREES COUNTERSUNK HEAD SCREWS WITH B.N.A.E.CROSS RECESS AND CONE POINT. SIM THREAD.)NF L22-189-1976有BNAE十字槽锥顶120°埋头螺钉.国际单位米制螺纹(120 DEGREES COUNTERSUNK HEAD SCREWS WITH B.N.A.E. CROSSRECESS AND CONE POINT. SIM THREAD.)NF L22-201-1984短螺纹精密螺钉.六角头.ISO螺纹(Bolt, hexagonal head, short thread, close tolerance. ISO thread.)。
螺丝手册
螺丝基础知识一、螺丝的结构螺丝头型部分螺杆部分槽的形状头的形状螺纹形状末端形状机丝螺钉自攻螺钉二、槽型的分类注：型十字槽为最常用槽型名 称槽型槽型六角三角十字组合一字型十字型十字名 称梅花四方字字梅花带柱梅花组合H 型十字槽规格三、常用头型的形状及分类(注：代码是为方便本公司管理而编制)头部形状头部形状名 称代 码盘头带介大平头平圆头六角头内六角头六角头带介半圆头大扁头中柱头半沉头沉 头盘 头代 码名 称四、常用螺纹的形状及各类（包括末端）螺纹形状自攻牙平尾自攻牙尖尾自攻牙尖尾机械开束尾机械开平尾名称代码注：代码是为方便本公司管理而编制规格(槽号)适用范围特征备注00#M0.6-M1.0极少用0#1种M1.4-M2.6小而浅2种M1.4-M2.6大而浅极少用3种M1.4-M2.6大而深1#M2-M2.6T 头M3属1#槽2#M3-M53#M6-M8螺纹形状自攻牙束尾铣尾自攻牙铣尾自攻牙双线束尾自攻牙双线自攻牙束尾名称代码注：代码是为方便本公司管理而编制代码名称三角自攻单牙三角自攻双牙三角自攻机械牙三角自攻机械牙螺纹形状注：代码是为方便本公司管理而编制五、螺丝的表面处理1、普通电镀名称彩锌白锌蓝锌黑锌白镍铬军绿锌锡代码CZn WZn Uzn BZn Ni Cr GZ Sn2、环保电镀3、其他涂饰六、常用螺钉线材的钢铁□代号与化学成分注：1、JISG3507（日本钢号标准）2、AISI（美国钢铁协会）、SAE（美国自动工作协（学）会）3、★号数量表示常用级别4、1006-1010材质多数用于制造无需热处理螺钉使用1018-1022材质多数用于制造热处理螺钉使用名称彩锌Cr3+白锌Cr3+蓝锌Cr3+黑锌Cr3+白镍Cr3+锡Cr3+代码CZn3+WZn3+UZn3+BZn3+Ni3+Sn3+名称达克罗耐落染色代码达克罗NYLOK染色钢铁代号化学成分%备注JIS G3507AISI SAE C Si Mn P(最高)S(最高)S06C 10060.08(最高)0.17-0.370.25-0.400.0400.050★★★S08C 10080.01(最高)0.17-0.370.30-0.500.0400.050★S10C 10100.08-0.130.17-0.370.30-0.600.0400.050★★★S12C 10120.10-0.150.17-0.370.30-0.600.0400.050★S18C 10180.15-0.200.17-0.370.60-0.900.0400.050★★★S22C10220.18-0.230.17-0.370.70-1.000.0400.050★★十字槽螺钉(JIS B 1111)一、适用范围本标准规定了一般用途的钢制、不锈钢制和黄铜制十字槽螺钉。
技友电动螺丝刀中英文彩色说明书
榮獲世界專利：Had passed through and got the patent certificates from:德國專利 Germany(G9405525.4)美國專利 U.S.A.(5310010) (4913242)(4756216) (4712456)義大利專利 Italy(00220090)韓國專利 Korea(0204888)台灣專利 Taiwan(for over 30 more ltems.)Since 1975 in TaiwanDirect Plug-In 110V/220V AC SeriesX 系列Direct Plug-In 110V/220V X SeriesA 系列Direct Plug-In 110V/220V A SeriesS 系列Direct Plug-In 110V/220V S SeriesRE/F 系列DC 30V RE/F SeriesRE/F-BL 系列Brushless Motor SeriesCY-D 系列DC 30V CY-D Series傳統式／氣吸式系列Traditional / VacuumISO 9001認證通過經營理念 Business Principle公司組織 Company Organization公司目標公司歷史及成就 Company History and Achievement「創新求進、永續經營」The innovation seeks improvement & lasting management技友牌電動起子不斷秉持「創新求進，永續經營」的精神，致力於自行研究開發，堅持不抄襲或仿冒國外產品，至今具有雄厚的新產品開發能力，並擁有創新進取的專業研發、生產和行銷管理等團隊，以生產製造符合客戶需要及經久耐用的工業級電動起子為目標，產品已行銷世界各國多年，並深獲客戶的肯定及信賴。
在其創建30多年後的今天，技友企業仍致力於不斷提供新的技術、產品和服務，確保客戶和合作夥伴可以相互依存、共同發展。
螺丝规格及其使用规范
基本技能訓練
螺絲規格及其使用規范
Jim.guo
1 2019/3/16
一.螺絲簡介
(一).螺絲大致分類:
第一种分法: T-SCREW 自攻螺絲 第二种分法: 公制螺絲 如:M3;M6等
12 2019/3/16
3.正確使用電批應注意事項 A.電批在使用時螺絲軸線應與電批頭軸線同心. B.手持電批時應便於鎖緊與鬆開,及手要能觸及 按鍵. C.在鎖螺絲應保証電批垂直或者水平. D.電批頭要具有一定磁性,以確保螺絲取拿,方 便作業. E.電批應固定牢固,防止脫落;且應有支架以便 於放置. F.電批嚴禁非工作狀態不間斷運轉長時間. G.嚴禁用電批頭橇起東西.
13 2019/3/16
14 2019/3/16
SCREW 非自攻螺絲 英制螺絲 #6-32
(二).螺絲電鍍方式:
NIB------鍍黑鎳 NIW------鍍白鎳 GREEN CATED-----綠色鍍層 YELLOW-----黃色鍍層 ZNC------鍍鋅白色 ZNC------鍍鋅五彩色. CRW-----鍍鉻 PSV-------鈍化處理 BCT------BLACK COATING 染黑
#6-40
40
3.484
3.356
32
24 24 20
4.142
4.800 5.461 6.322
3.991
#10-32 4.618 #12-28 5.279 6.117 1 / 4-28 32 4.803 4.651
#10-24 #12-24 #1/4-20
28
5.461
5.296
28
螺纹锁固用户指南说明书
Threadlocking User’s GuideWhat you need to know to ensure a reliable threaded assemblyLoctite® – Finding a Better WaySince the design of threaded fasteners, engineers havebeen searching for the solutions to vibrational loosening.Vibration loosening of fasteners creates relability issues,Prone to rust•Better WayLoctite ThreadlockersInvented fifty years ago by Loctite Corporation, now Henkel Corporation,this revolutionary method to lock and seal threaded fasteners withliquid anaerobic adhesives has found worldwide acceptance. Suited fora wide range of applications, from delicate electronic components toheavy industrial equipment, Loctite® threadlockers have dramaticallyincreased the reliability of threaded assemblies.Benefits of Loctite•Lock nuts and bolts against vibration and thermal expansion•Seal against corrosion and leakage•Reduce inventory costs•Suitable for all shapes and sizes of fasteners•Act as a thread lubricantMaintain critical adjustments of the assembly••No on-torque adjustments needed•High chemical resistanceLoctite® Threadlocking Guide Table of ContentsTHREADED FASTENERSWhy do threaded assemblies fail?Threaded FastenersFunctions of a threaded assembly1. Create clamp force2. Maintain clamp force Clamp ForceCorroded assemblies can be difficult to take apart......which can lead to broken bolts.Parts toleranceVibration and looseningStretching of the bolt beyond its yield point and thermal expansion/contraction of parts leads to lack of structural rigidity and relaxation of partsDispensing Optionsthreadlocker?For through holesFor blind holesFor post assembly (using Loctite 290)250 ml and 50 ml Loctite hand pumpsHow does a Loctite ®threadlocker work?Fill GapsLoctite ®threadlockers are single-component adhesives that cure in the absence of air and in contact with active metal to form a tough thermoset plastic. They completely Loctite threadlocker between the interfacing threadsFor overhead applicationsFor maximum convenience andproductivity, Loctite ®threadlockers can be dispensed through Loctite ®dispensing Loctite integrated semiautomatic dispenser, dispense valve, and stationary dispense valveEngagement area of rusty bolt that did NOT have Loctite threadlocker appliedEngagement area of rusty bolt that DID have Loctite threadlocker appliedLoctite ®Threadlocking SolutionsLoctite® Threadlocking SolutionsWhy use Loctite® threadlockers?ConventionalLOCKNUTS SPRING WASHERS NYLON INSERTS TAB WASHERS / SPLIT PINSStrengthLow strength: • Ideal for fasteners <M6. Easy disassembly using hand toolsLoctite ®threadlocker key selection factorssticks semisolid formula can be applied beforehand on bolts that are waiting to be assembled liquid threadlockers are designed to be applied at the moment that parts will be assembled Easy disassembly with hand tools when using Low & Medium Strength formulasWhen assembling metal parts with inactive surfaces, Loctite ®primers are Loctite 7088 PrimerLoctite ®Threadlocking SolutionsSelectors chartLow strength Core liquid line:Loctite ® 222M14-55°C to + 150°C purple fluorescent CriteriaProductThread size uptoOperating temperatureColourApplication Cases7König + Neurath AGAssemblies in seating furniture are subject to enormous forces of motion. König + Neurath AG uses threadlocking adhesives on variousApplication CasesEhlebracht Slowakei s.r.o.A large portion of LCD and plasma monitors are mounted on rotatingholders before being fixed to the wall. Ehlebracht Slowakei s.r.o.manufactures these mounting devices for the electronics industry. Asthese holders are often subject to numerous load cycles there is a highrisk of self-loosening of the nuts and bolts. To counteract this problem,wicking grade threadlocker Loctitescrew after assembly.Professional Barrier Systems Ltd.Professional Barrier Systems Ltd. manufactures the highly respectedExtendor range of physical security devices for the protection ofwindow and door openings. The systems feature retractable grilleswhich blend into door and window surrounds when they are not in use.From a security standpoint, preventing the barrier’s threaded lockingmechanism from moving is a necessity. For this crucial task Loctite268 threadlocking stick is applied before assembling the parts.Hiller GmbHThe decanter centrifuge has become a major processing tool in a widerange of applications, e.g. for the separation of waste water and rapeseed. The environment is harsh and chemical resistance is needed forall parts of the centrifuge. For components such as the bowl, conveyor,base frame, housing and most of all the centrifuge drive it is veryimportant to prevent loosening and corrosion of the fasteners to ensurereliability of the components. As a result, manufacturer Hiller GmbHuses LoctiteHILLERWe trust in Loctite® Threadlocking Solutions46/F, Menara Telekom (South Wing)Henkel Taiwan Ltd.10/F, No. 866 Chung Cheng Road Chung Ho City, Taipei County 235Taiwan (R.O.C)Tel: +886-2-2227 1988Fax: +886-2-2226 8699Henkel (Thailand) Ltd.35/F, Central World Tower 999/9 Rama I Road Khwaeng Patumwan When you choose the Loctite ®brand, you receive much more than areliable assembly, you obtain a comprehensive solutions package:Wide product range •Loctite ®Solutions。
螺杆钻具使用手册(中英文对照版)
1、前言上海奥森油田服务有限公司为渤海石油有限公司（天津）钻井部提供螺杆钻具设备服务，与此同时联同各油田、科研院所，在消化国内外先进技术，结合我国国情的基础上，开发和制造出多种型号的螺杆钻具，能为油田提供满意服务。
本手册主要介绍螺杆钻具的性能和使用要求以及注意事项，便于用户更好地了解我公司的钻具，结合钻井的需要，选好、用好、维护好钻具，发挥其应有的技术性能，提高钻井经济效益。
2．螺杆钻具工作原理螺杆钻具是以泥浆为动力的一种井下动力钻具。
泥浆泵泵出的泥浆液流经旁通阀进入马达，在马达进出口处形成一定压差推动马达的转子旋转，并将扭矩和转速通过万向轴和传动轴传递给钻头。
螺杆钻具的性能主要取决于螺杆马达的性能参数。
3．螺杆钻具的组成螺杆钻具由旁通阀、马达、万向轴和传动轴四大总成组成（如图1）表 1 Table 15LZ165X7。
0Y BH 5LZ165X14。
0 BH q = 8。
5 5LZ197X7。
0Y BH 5LZ197X14。
0 BH q= 14。
0 5LZ120X7。
0Y BH q = 5。
0 5LZ95X7。
0Y BHq = 2.6按以上推荐计算公式，用户可以根据使用需要随时更换不同直径的喷咀，从而达到理想的效果。
Based on the above recommended equation, the customers can timely change different diameter nozzles according to the actual demand, so as to reach ideal effect.3．3 万向轴总成万向轴的作用是将马达的行星运动转变为传动轴的定轴转动，将马达产生的扭矩及转速传递给传动轴至钻头。
万向轴大多采用瓣形，也有采用挠轴形式的。
渤海启明钻具的瓣型万向轴采用线切割技术制成，切口平行度高，粗糙度可达且不破坏金属化学成分，因此使用寿命高、机械损失小（如图4）。
自攻螺丝介绍及规格表
自攻螺丝一般是指尖头的，粗牙的，质地较硬的木螺丝，也有用于铝合金、塑料的。
用于金属孔开螺纹的一种特殊自攻螺丝被叫做丝攻。
自攻螺丝用于非金属或较软的金属,不用打低孔和攻丝;自攻螺丝是尖头的,这样才能"自攻"；普通螺丝都是平头的,粗细一致.自攻螺丝是说：钻的孔为无屑攻牙的孔，用的螺丝和一般的不同，头为尖尖的，牙距比较大，与无屑丝攻有点像，可以不用攻牙直接旋进去，金属与塑胶通常使用这种方法。
自攻螺丝，就是不用螺母的螺丝。
它可以在被固结的材料上，靠其自身的螺纹，将被固结体“攻－钻、挤、压”出相应的螺纹，使之相互紧密配合。
补充：（来自同济大学教材）自攻螺丝是一种带有钻头的螺丝，通过专用的电动工具施工，钻孔、攻丝、固定、锁紧一次完成。
自攻螺丝主要用于一些较薄板件的连接与固定，如彩钢板与彩钢板的连接，彩钢板与檩条、墙梁的连接等，其穿透能力一般不超过6mm，最大不超过12mm。
自攻螺丝常常暴露在室外，自身有很强的耐腐蚀能力；其橡胶密封圈能保证螺丝处不渗水且具有良好的耐腐蚀性。
自攻螺丝通常用螺钉直径级数、每英寸长度螺纹数量及螺杆长度三个参数来描述。
螺钉直径级数有10级和12级两种，其对应螺钉直径分别为4.87mm和5.43mm；每英寸长度螺纹数量有14、16、24三种级别，每英寸长度螺纹数量越多，其自钻能力越强。
1发展(Evolution):自1914年自攻螺丝开始商品化.第一次之设计─主要源自木螺丝─系属可渗碳钢锥尾A型螺纹成型螺丝.当时主要之用途是用在空调系统导管上铁皮之接合,因此又叫做铁皮螺丝.经过80余年之发展,共可分为四个时期─螺纹成型、螺纹切削、螺纹滚成及自钻。
螺纹成型自攻螺丝(Thread Forming Tapping Screws)─系直接由铁皮螺丝发展而来,螺纹成型自攻螺丝使用时须预先钻孔,再将螺丝旋入孔中,强力挤出配合阴螺纹,而原来在阴螺纹位置上之材料将被挤到阳螺纹之间,此谓之螺纹成型自攻螺丝.仅可适用于薄且具有可塑性之材料,因此又发展出;螺纹切削自攻螺丝(Thread Cutting Tapping Screws)─在螺纹之尾端切割出一或多道之切削口,使能在旋入预钻孔时,利用螺丝尾部及牙部以类似螺丝攻的方式切削出配合阴螺纹.它可以用在厚板,比较坚硬或易碎等不易塑造之材料,.螺纹滚成自攻螺丝(Thread Rolling Tapping Screws)─三角牙自攻螺丝,又称为Type TT(Type Tai目前仍有专利)系基于成型螺丝攻之原理发展而成,螺纹滚成自攻螺丝具有特殊设计之螺纹及尾端使螺丝可以在断续之压力下自行滚成配合之阴螺纹.同时在孔周围之材料可以更轻易的填补自攻螺丝螺纹及牙底之空间,由于其磨擦力较螺纹成型自攻螺丝为小,因此可以使用在更厚之材料上,旋转所需之扭矩更好控制,且组合后强度更高.螺纹滚成自攻螺丝其工程标准定义比成型或切削自攻螺丝在材料,热处理,强度上之定义更高且更为明确,使得螺纹滚成自攻螺丝成为真正的”构造用”扣件.钻尾自攻螺丝(Self Drilling Tapping Screws)─又称为Tec,在组装自攻螺丝之所有过程中,最耗费成本的是预钻孔的准备.自攻螺丝的使用,必需先钻孔.而且孔径也必需限制.无需预钻孔而在某些方面可以节省成本.这就是集钻,攻,旋紧于一次作业的钻尾自攻螺丝.钻尾螺丝的表面硬度及心部硬度比一般自攻螺丝高一点,这是因为钻尾螺丝多了一个钻孔之作业,另外钻尾螺丝尚需作贯穿试验,用以测试螺丝可以在规定时间内钻孔并攻出螺纹.上述为四种主要自攻螺丝之设计及发展过程,另有两种为特殊螺纹设计之螺丝,第一种为;高低牙自攻螺丝(High–Low Tapping Screws)─使用在塑料或其它低密度材料。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
一、螺丝通用技术条件
如无其它规定,则按本公司以下要求:
1.外观质量检查:
表面镀层/氧化层均匀致密,无露底、脱落、变形、缺口、裂纹和披锋等不良.
2.盐雾腐蚀试验: 350C/5%NaCl水溶液/2hrs.
3.可针对具体要求, 对样品作扭力装配试验
二、分类
本公司涉及的螺丝分类如下:
2.1PA--圆头尖脚螺丝
2.2PB--圆头平脚螺丝
2.3PT--圆头介脚螺丝
2.4BA—大头尖脚螺丝
2.5BT--平脚介脚螺丝
2.6KA--平头尖脚螺丝
2.7KB--平头平脚螺丝
2.8KT--平头介脚螺丝
2.9PWA/ WA--带介子尖脚螺丝
2.10PWB /WB--带介子平脚螺丝
2.11PWT/ WT--带介子介脚螺丝
2.12PM--圆头机牙螺丝
2.13KM--平头平脚机牙螺丝
2.14六角机牙螺丝
代号说明: A-尖脚; B-大头,平脚; M-机牙; K-平头; P-圆头; T-介脚; W-带介子.
电镀种类
蓝锌白锌五彩镀红铜镀黄铜
黑锌+防锈油黑锌+Lacquer涂装镀镍
镀锡
镀铬镀古铜不锈钢清洗
■基本头型
P 头 B 头V 头喇叭头
R 头T 头O 头H 头
C 头 F 头I 头IP 头■基本槽型
十字槽十一槽一字槽
梅花槽六角槽米字槽
精密机械牙小螺丝
*种类
1.精密小螺丝 ( 1.4 <= d <
2.6 )
2.特殊极微小螺丝 ( d < 1.4 )
.*头型
*螺丝公差
2.1 PA--圆头尖脚螺丝
实物图片结构示意图
2.2PB--圆头平脚螺丝
2.3 PT--圆头介脚螺丝
2.4 BA—大头尖脚螺丝
2.5 BT—大头介脚螺丝
2.6 KA—平头尖脚螺丝
2.7 KB--平头平脚螺丝
2.8 KT----平头介脚螺丝
2.9 WA--带介子尖脚螺丝
2.10 WB/PWB--带介子平脚螺丝
2.11 WT/PWT---带介子介脚螺丝
2.12 PM--圆头机牙螺丝
2.13 KM--平头机牙螺丝
2.14六角机牙螺丝
PA--圆头尖脚螺丝
PB--圆头平脚螺丝
PT--圆头介脚螺丝BA—大头尖脚螺丝
BT--平脚介脚螺丝
KA--平头尖脚螺丝
KB--平头平脚螺丝
KT--平头介脚螺丝
PWA/ WA--带介子尖脚螺丝P WB/WB--带介子平脚螺丝PWT/ WT--带介子介脚螺丝PM--圆头机牙螺丝
KM--平头平脚机牙螺丝。