石油钻井英语

合集下载

教材:石油钻井常用英语手册

教材:石油钻井常用英语手册

A Handbook of English for Oil Drilling石油钻井常用英语手册职工培训教材系列辽河石油勘探局钻井二公司六分公司二OO七年四月A Handbook of English for Oil Drilling石油钻井常用英语手册一、DRILLING 钻井1.Carry out drilling operation in accordance with the drilling program. 按钻井程序进行钻井作业.2.Prepared bell nipple. 准备”喇叭口”短节.3.Make up 2 joints of drill pipe. 接两根钻杆.4.Break out this connection. 卸开该接头.5.Make up bottom hole assembly. 组合下部钻具6.Check and reset crown-saver on every tour. 每个班都要检查并重新调整天车防碰装置.7.Number stands on trip out and trip in. 起下钻时给立柱编号.8.Pick up BHA and run to seafloor. 将下部钻具下到海底.9.Pick up stands. 接立柱10.Don’t drill faster than 15 minutes for 1 stand. 钻进速度别超过15分钟1根立柱11.Drop TOTCO. 投(陶特)测斜仪12.Fish TOTCO with overshot. 用打捞筒捞起测斜仪13.Resume drilling to T.D. 继续钻进到总深14.Circulate 15 minutes.循环15分钟15.Run in hole. 下钻16.Put out of hole. 起钻17.Make an inventory of all ring gaskets. 开一个所有垫圈的清单e spinning tong. 使用气动扳手19.Operate the air winch. 操作气动绞车y down 57 joints of 5” drill pipe. 甩57根钻杆21.Pick up drill stem test tool. 提起钻杆测试工具22.Circulate mud for 2 hours. 循环泥浆2小时23.Move string during circulation. 在循环时注意活动钻具24.Circulate hole clean. 循环清洗井眼25.Circulate bottoms up. 循环泥浆几周26.Fill up every 5 stands. 每5柱灌泥浆一次27.Check mud weight every 15 minutes. 每15分钟检查泥浆比重28.Reverse out excess cement. 反循环替出多余的泥浆29.Change/replace old mud by new mud. 用新的泥浆替换出旧的泥浆30.Stop drilling. 停止钻进31.Drilling ahead. 钻进32.Pull out of hole bit. 起出钻头33.Change bit. 换钻头34.Run the wear bushing. 下抗磨补心35.The bit thread type is regular pin. 钻头丝扣是正规公扣36.What’s the make-up torque? 上扣扭矩要多大?37.Run in 9” collars. 下9”钻铤38.The cathead ca n’t give enough torque. 猫头力量不够39.Connect crossover sub. 接上配合接头40.The tong angle is too small. 大钳的角度太小了41.Stop circulating. 停止循环泥浆42.Break out the stand. 卸立柱43.Set the single into the mousehole. 把这个单根放进鼠洞44.Can we break out the pipe with rotary table? 可用转盘卸扣吗?45.No! Break it out with tong. 不行! 要用大钳卸扣46.Spin it out with the air spanner. 用气动扳手卸扣47.Put the pipe wiper on the string. 装上钻杆刮泥器48.Don’t set this stand back. 这根钻杆不要放在钻杆盒上49.Make up the lift sub. 接好提升短节50.Secure the safety clamp. 上紧安全卡瓦51.The bit is nearing the shoe. 钻头快到套管鞋了52.Slow down the running speed. 放慢下放速度53.This is the undergauged interval. 这是缩径井段54.This is the drilling program. 这是钻井设计书55.How much weight on bit is required? 要加多少钻压?56.Keep the rotary speed at 120---140 RPM. 转速保持120---140转/分57.Keep the flow rate at 3000 LPM. 保持排量3000升/分58.The pump pressure is too high. 泵压太高了59.Don’t ream the hole too fast. 划眼不要太快60.Notice the rotary torque. 注意转盘扭矩的变化61.The penetration rate is getting slower. 钻速变慢了62.The bit is nearly worn out. 钻头快磨光了63.Stop drilling at 2000 meters. 钻至2000米停钻64.Circulate for one hour. 循环一个小时65.The pump pressure has increased. 泵压升高了66.One nozzle may be plugged. 可能有一个水眼(或: 喷嘴)堵了67.What is the hook load? 悬重多少?68.What’s the pick-up weight? 上提重量是多少?69.What’s the lowering weight? 下放重量是多少?70.Run in HWDP. 下加重钻杆71.A stabilizer is needed here. 这里需要一个扶正器72.This is a flexible sub. 这是挠性接头73.This is the BHA log. 这是下部钻具组合记录74.Record all outside and inside diameters. 记录好所有(入井工具的)内外径75.We need a short drill collar. 需要一根短钻铤76.Pull the cat line. 拉猫头77.Operate the break lever. 操作(或:扶)刹把78.Stop the pumps. 停泵79.Make a wiper trip. 通井80.Retrieve wear bushing. 取出抗磨补心81.Bleed off pressure. (释)放压(力)82.Keep 5 wraps on the drum. 滚筒上留5圈83.Set slips. 座上卡瓦84.If tight hole, repeat wiper trip. 如果井眼紧, 重复划眼85.Setback bottom hole assembly. 将下部钻具立于钻杆盒内86.Make sure all alarms are on. 确保所有的警报信号都开着y down TDS spinner. 拆下顶部驱动的旋扣器88.Run in hole bit #15 to bottom. 用15号钻头下钻到井底89.Run in hole to casing shoe. 下钻至套管鞋90.Pick up same bit and BHA. 装上同样的钻头和钻具组合y down 5” HW drill pipe. 甩5”加重钻杆92.Move string every 2 hours. 每2小时活动钻具一次93.Keep area around shaker clean. 保持振动筛区域干净94.Control trip gas. 控制起下钻气95.Ream if needed. 如必要时进行划眼96.Select the best penetration rate. 选择最佳钻进速度97.Fix the traveling assembly. 固定游动系统98.Check power tongs and spinning rope are on drill floor. 检查动力钳和尾绳是否在钻台99.What’s the we ight on bit? 钻压是多少?100.What is the BHA of this well? 这口井的下部钻具如何组合?101.Drill out cement. 钻穿水泥102.Drill out 20” casing shoe. 钻穿20”套管鞋tch the elevator. 扣吊卡104.Unlatch the elevator. 开吊卡105.Set the slips. 放卡瓦106.Adjust the crown-o-matic (crown saver). 调整防碰天车107.Lock the hook pin. 锁紧大钩销子108.Check OD of stabilizer. 检查扶正器的外径109.Perform leak off test. 进行地层破裂(或:渗漏)测试110.Connect kill and choke line. 接上压井和放喷管线111.Reverse out the drill pipe. 反循环清洗钻杆112.Make a short trip. 进行短途起下钻113.Change the cutters. 换割刀114.Slug the pipe. 灌重泥浆115.Drill the stand down. 钻完立柱116.Start/run the shale shaker. 开振动筛117.Start the desanders. 开除砂器118.Start the desilters. 开除泥器119.Change it with a 40 mesh screen. 换成40目筛布120.Shut it off. 关掉121.Pull it to the cat ramp. 把它拉到坡道上去122.Make a fast connection. 接单根要快123.Don’t dump the mud into the s ea. 不要把泥浆排放到海里124.Disconnect it with a chain tong. 用链钳卸开125.Put a thread protector. 加一个(丝扣)护箍126.Can we use the power slips? 可以使用动力卡瓦吗?二、CASING AND CEMENTING 下套管与固井127.R un in hole to bottom for wiper trip. 下钻通井128.T his is the casing program. 这是套管程序129.P repare for running casing. 准备下套管130.M ake everything ready for running 7”casing. 做好下7”套管的准备131.M ake cementing job. 固井132.D isplace cementing with mud pump. 用泥浆泵替泥浆133.S et cement plug from 2940 to 2790m. 在2940到2790米井段打水泥塞134.P ick up cementing head. 接水泥头135.C ement samples are hard. 水泥样已凝固136.P ump in 3 cubic meters of spacer. 注3方隔离液137.P ump down the plug. 泵压(胶)塞138.W ait on cement. 候凝139.T he guide shoe will be connected. 接引鞋140.C onnect the floor collar. 接浮箍141.C onnect the air line to the casing stabbing board. 接好套管扶正台的气管线142.R un casing with the 350T slip elevator. 用350吨卡瓦式吊卡下套管143.C lean and dry 20” casing threads with rags. 清洁并擦干20”套管丝扣144.W here is the rabbit for drifting the casing? 套管通径规在哪里?三、FISHING 打捞145.The bit cutters have been lost in the hole. 牙轮落井146.Run in the reverse-circulation basket. 下反循环打捞篮147.There is a lot of junk in the hole. 井下有很多落物148.The fish is 235.46 meters long. 落鱼长度235.46米149.The fish top is at 2478.34 meters. 鱼顶位置2478.34米四、FREEING STUCK PIPE 卡钻与解卡190.The down-hole problems are very complicated. 井下情况很复杂191.The hole is tight. 遇阻了192.Overpull while tripping out. 起钻遇卡(overpull: 超拉力)193.The formation is unstable. 地层不稳定194.The wall caving is severe. 井壁垮塌严重195.There are many return cuttings. 返出岩屑特别多196.The mud returns have decreased. 返出泥浆减少197.The hole is enlarged. 井眼扩大了198.The pipe’s stuck. 卡钻了199.Pull up to 150 tons. 上提150吨200.Slack off to 50 tons. 下放至50吨201.Ream down all the tight points. 在所有遇阻点进行划眼202.The rotary table can’t rotate. 转盘转不动203.Where is the sticking point? 卡点在哪里204.Make a tensile test. 做拉伸试验205.Back it off above the free point. 在卡点以上倒扣206.Where is the back-off position? 脱扣位置在哪207.Plug the well for side tracking. 打水泥塞侧钻五、ABNORMAL WELL CONDITION AND WELL CONTROL异常井况与压井168.The mud is gas out. 泥浆有气侵169.The pit has lowered quickly. 泥浆池液面下降很快170.The hole lost returns. 井口不返泥浆171.The returns are unstable. 返出泥浆量忽大忽小172.Where’s the thief zone? 漏失层在哪里173.Cut down the flow rate. 降低排量174.Lower the mud density. 降低比重175.Cut down the hydrostatic pressure. 减少静压176.The gas smell is strong. 天然气味度很浓177.There’s some trace of oil. 发现有油花178.The pump pressure is fluctuating. 泵压不稳179.It is a zone of abnormal pressure. 这是异常压力层180.The hole (well) is kicking! 井涌啦!181.Shut in the BOP! 关闭防喷器182.Sound the general alarm quickly! 快发出综合警报183.The stand pipe pressure is 10 kg/cm2. 立管压力10公斤/厘米2184.The casing pressure is 25 kg/cm2. 套压2510公斤/厘米2185.Fill out the kill sheet. 填写压井记录表186.Kill the well. 压井187.Ther e’s a combination of lost returns and the kick. 又喷又漏, 情况复杂188.Reverse the gas out of the hole. 反循环排气189.What’s the lag time? 迟到时间是多少190.The well is now stable. 现在井眼已经稳定六、PREPERATION BEFORE MAKING HOLE钻前准备191.Tell the mechanic to check the motor torque . 让机械师检查马达扭矩。

石油行业常用英语词汇(全面)

石油行业常用英语词汇(全面)

石油行业常用英语词汇(全面)1. 石油勘探(Petroleum Exploration)Seismic survey:地震勘探Exploration well:探井Reservoir:储层Porosity:孔隙度Permeability:渗透率2. 钻井与完井(Drilling and Completion)Drilling rig:钻机Bit:钻头Drill pipe:钻杆Casing:套管Cementing:固井Completion:完井Fracking:水力压裂3. 采油与生产(Oil Production and Extraction)Production well:生产井Pumpjack:抽油机Artificial lift:人工举升Separator:分离器Flowline:输油管线Tank farm:储油罐区4. 石油加工(Petroleum Refining)Crude oil:原油Refinery:炼油厂Distillation:蒸馏Cracking:裂化Catalytic reforming:催化重整Asphalt:沥青Lube oil:润滑油5. 石油产品(Petroleum Products)Gasoline:汽油Diesel:柴油Jet fuel:航空煤油Fuel oil:燃料油Petrochemicals:石油化工产品6. 安全与环保(Safety and Environmental Protection)HSE(Health, Safety and Environment):健康、安全与环境 Spill:泄漏Emission:排放Waste treatment:废物处理Environmental impact assessment:环境影响评估7. 国际合作与市场(International Cooperation and Market)OPEC(Organization of the Petroleum Exporting Countries):石油输出国组织Brent crude:布伦特原油NYMEX(New York Mercantile Exchange):纽约商品交易所Spot market:现货市场Futures contract:期货合约本文档为您提供了石油行业常用英语词汇的全面梳理,希望对您的工作和学习有所帮助。

石油专业英语复习资料

石油专业英语复习资料

石油专业英语复习资料Section 1Petroleum 石油Drilling 钻井Kelly 钻杆String 管汇、管柱Drill pipe 钻杆BHA(Bottom Hole Assembly) 底部钻具组合Sub/joint 接头Collar 钻铤Bit 钻头Finger bit 刮刀钻头Toothed bit 牙轮钻头Diamond bit 金刚石钻头DC 钻铤DS 钻柱Section 2Cat walk 猫道、滑道Cat head 猫头dog house (司钻)休息室、值班室dog leg 狗腿goose neck 鹅颈管monkey board 猴台(二层台)rat hole 大鼠洞mouse hole 小鼠洞fish 落鱼fishing 打捞kick 井涌BOP 防喷器KOP 造斜点Section 3Straight well 直井Directional well 定向井Horizontal well 水平井Extended reach well 大位移井Superdeep well 超深井Underbalance drilling 欠平衡钻井Casing drilling 套管钻井Drilling operations 钻井操作Make a trip/tripping 起下钻Trip up/out 起钻Trip in/down 下钻Make a connection 接单根Completion 固井Completion 完井Logging 测井、录井Derrick system 起升系统Rotary system 旋转系统Draw works 绞车Rotary table 转盘Circulating system 循环系统Muclpump 钻井泵Section 4 Hoisting system 起升系统1 Crown block 天车Traveling block 游动滑车(游车)Hook 大钩Wire line 钢丝绳Derrick 井架2 The type of derrick 井架类型Pyramid derrick 塔式井架Self-elevating derrick 自升式井架Cantilever derrick 前开口井架A-mast derrick A形井架W-mast derrick 桅形井架3 The draw works 绞车刹车Main brake 主刹车Assist brake 辅刹车Band brake 带式刹车Disc brake 盘式刹车Electromagnetic brake 电磁刹车Eaton brake 伊顿刹车Brake band 刹车带Brake drum 刹车筒Pitman 连杆Brake handle 刹把Brake block 刹车块Hydraulic disc brake 液压盘刹Section 5 The rotary system 旋转系统1 Rotary table 转盘Turntable 转台Master bushing 方补心Swivel 水龙头Top drive 顶驱Rotary hose 水龙带Standpipe 立管2 三管goose neck 鹅颈管wash pipe 冲管base pipe/center pipe 中心管3 三轴承main bearing 主轴承upper alignment bearing 上扶正轴承lower alignment bearing 下扶正轴承4 四密封upper machine oil seal 上机油密封lower machine oil seal 下机油密封upper drilling fluid seal 上钻井液密封lower drilling fluid seal 下钻井液密封section 6 The drilling fluid 钻井液1 Mud 泥浆Slurry 水泥浆2 The drilling fluid 钻井液Water base drilling fluid 水基钻井液Oil base drilling fluid 油基钻井液Oil-in water 水包油Water-in-oil 油包水Synthetic drilling fluid 合成基钻井液3 Liquid phase 液相Water 水Oil 油4 Solid phase 固相Clay 粘土Adulterant 加重剂Treating chemical 化学处理剂5 Bentonite 搬土Barite 重晶石Sang content 含砂量Solid phase content 固相含量Colloid 胶体Emulsion 乳状液Foam 泡沫Density 密度Viscosity 粘度Shear 切力Filtration 滤失Viscometer 粘度计Filter press 失水仪Density meter 密度计Section 7 The rig personnel 井队人员编制The rig personnel 井队人员编制Tool pusher 队长Assistant tool pusher 副队长Diller 司钻Secretary 书记assistant diller 副司钻derrickman 井架工roughneck 钻工beach worker 钳工mud man 泥浆工section 8 power and drive system 动力驱动系统1 Power and drive system 动力驱动系统Diesel engine 柴油机Current 电源DC(direct current) 直流电AC(alternating current) 交流电2 The plane of drive 驱动方式Unity drive 统一驱动Unit drive 单独驱动Subunit drive 分组驱动3 Power equipment 驱动设备Mechanical drive 机械驱动Electric drive 电驱动Combination drive 复合驱动Section 9 the actuating system 传动系统1 Type of actuating 传动类型Belt 胶带、皮带Chain 链条Gear 齿轮2 Belt rig 胶带钻机Chain rig 链条钻机Gear rig 齿轮钻机3 Hygraulic drive 液压传动Hygrodynamic drive 液力传动Electric drive 电传动4 Braking 减速Paralleling 并车Astern 倒车Shift 变速Section 10 the control system 控制系统1 The control system 控制系统Air control 气控Air feeder 供气设备Executive element 执行元件Control element 控制元件Assistant element 辅助元件2Air feeder供气设备Air compressor 空气压缩机Air tank 储气罐Air purification equipment 空气净化设备3Excutive element 执行元件Cylinder 气缸Air motor 气马达Air drive friction clutch 气动摩擦离合器Control element 控制元件Pressure control valve 压力控制阀门Temperature control valve 温度控制阀门Flow control valve 流量控制阀门4 Assistant element 辅助元件Antiflocculant 防凝器Alarm 报警器Potating joint 旋转接头Fitting 管汇、管件Section 11 The sub structure system 底座系统1 drilling floor 钻台Derrick 井架Drawworks 绞车Roary table 转盘Pipe setback 立根盒Wellhead tod 井口工具Driller” console 司钻控制台2 control room 机房Power package 动力机组Actuating equipment 传动机组Section 12 The assistant system 辅助系统1Blowout preventer(BOP) 防喷器Kick 井涌、溢流Blowout 井喷Well control 井控Shut well in 关井Kill the well 压井2 BOP 防喷器Rotary BOP 旋转防喷器Annulus BOP 环形防喷器Double ram type BOP 双闸板防喷器Spool 四通Ram type BOP 单闸板防喷器。

石油专业英语常用

石油专业英语常用

石油专业英语常用The Standardization Office was revised on the afternoon of December 13, 2020石油专业英语(常用)油井(oilwell)指任何钻透地球表面(Earth'ssurface)的钻孔(boring),目的是发现(find)或生产(produce)石油(petroleum/oil/hydrocarbons)。

专门生产天然气的叫气井(gaswell)。

油井一般经历五个阶段:计划(planning)、钻井(drilling)、完井(completion)、生产(production)与报废(abandonment)。

首先用钻机(drillingrig)通过钻具(drillstring)上的钻头(drillbit)在地上钻出毫米的孔(hole),然后在钻孔(borehole)中下钢制油管(steeltubing)与套管(casing)。

套管与钻孔之间还可能需要用水泥(cement)来固定。

套管为井孔(wellbore)提供结构上的整体性(structuralintegrity),同时隔离(isolate)危险的高压区(highpressurezone)。

随着井深加大,钻头和套管尺寸会变小。

现在的油井通常都有2-5个逐渐变小的井口尺寸。

钻头通过与之连接的钻铤(drillcollar)来钻进岩层。

钻井液(drillingfluid/mud)通过钻杆(drillpipe)内部泵入钻头,作用包括冷却(cooling)钻头、提升钻屑(drillcuttings)、避免井壁(wellborewall)不稳定以及避免岩层液体由于压力进入井眼。

使用过的钻井液用振动筛(shaker)去掉钻屑后返回泥浆池(pit)循环利用。

通过在地面的顶部驱动装置(topdrive/kellydrive)增加额外的10米长的钻杆(joints)来增加钻井深度。

石油工程专业英语教学内容

石油工程专业英语教学内容

第一章石油钻井工程英语基础第1节石油钻井工程基础词汇1.钻探,钻井:drill————拓展记忆钻井:drilling定向斜井directional drilling 欠平衡钻井under-balance 海上钻井off-shore陆地钻井on-land drilling 钻头:drill bit 刮刀钻头:drag bit 牙轮钻头rock bit金刚石钻头diamond bit 喷射钻头jet bit 钻铤drill collar 衣领collar钻杆:drill pipe 钻井队drilling crew 钻机drill rig 钻井泥浆drilling mud钻井液drilling fluid2.油,石油:oil————拓展记忆原有crude oil 石油petroleum 中国石油Petro-China 采油oil production采油设备oil production equipment 采油平台oil production platform 油泵oil pump3.地质:geology————拓展记忆地质专业人员geologist 物理physics地球物理勘探geo-physical probe,geo-physical exploration测井logging 测井作业logging operations 测井记录logging record4.油井:well————拓展记忆井眼hole 油井oil well 试井,油井测试well test 井下down-hole井下作业down-hole operation第2节石油钻井方法基础词汇原油crude oil 天然气natural gas 煤层气coal-bed gas 一体化设计integral design钻井drilling 钻井原理the principles of drilling顿钻钻井percussion drilling,cable-tool drilling 旋转钻井rotary drilling液体冲击fluid percussion 大位移big deviation侧钻井sidetracking drilling technology lateraldrilling水平井horizontal well 探井wildcat,wildcat drilling 深井deep well 浅井shallow well老井maturing well 欠平衡钻井under-balanced drilling 丛式钻井cluster drilling technology 煤层气井coal-bed gas well 生产井production wells 报废井abandon wells停产井non-production wells 绕障井、三维井three-dimensional wells常温井normal temperature well 注采井injection and production well 稠油井heavy oil well热洗井hot washing pipe 井况well condition石油钻井技术基础词汇技术规范,技术指标,技术性能:specification拉伸tension 拉伸强度tension strength 应力stress 压力pressure 应力点stress point压力等级pressure grade 压力降pressure drop 压力梯度pressure gradient回压back pressure 大气压atmosphere 压差differential pressure静液柱压力static fluid column pressure 特征characteristic,feature定性讨论qualitative argiment 定量使用quantitative use液体liquid 固体solid 气体gas,air 正的positive 负的negative虚线dashed line,broken line 实线full line 递减率decline rate 正比于be proportional to 水平的horizontal 垂直的vertical 油层静压the formation static pressure石油钻井参数基础词汇负荷load 扭矩torque 扭转twist 摩擦friction钻压WOB, weight on bit,weight, drilling weight钻速rate of penetration, drilling rate, the rate of drilling, average ROP 钻井周期drilling period 钻速rotary speed 地层压力预测formation pressure prediction technology地层快速预测the formation fast prediction 埋藏深度bury depth产油层,产油带,pay zone,productive formation温度梯度temperature gradient 地层压力formation pressure 坍塌压力collapse pressure破裂压力fracture pressure 平衡压力equilibrium pressure钻具(柱)压力drilling string pressure 钻头振动vibration of bit 钻井成本drilling costs井眼尺寸hole size,well size 参数计算parameters calculation几何参数geometric parameters 参数分析parameter analysis 动态参数dynamic data静态监测static data 注水参数parameter of injection 参数、变量variables 井距well space 垂直深度vertical depth 水平位移horizontal deviation 总深度total depth水平位移horizontal displacement 最大井斜角maximum hole inclination井眼环空annulus space 压力调节器pressure regulator 恢复(增加)压力the build-up pressure 初始开采primary recovery 含水地层water bearing formation 套管漏失casing leak摩擦损失friction losses 气聚阀gas-lift valve 石蜡族paraffin series含气液柱gas-laden column 增产措施stimulation treatment 流动能力flowing capacity生产速率production rate 水驱water drive 气驱gas drive 网状系统grid system水侵water influx 五点法five-spot pattern 油井产量well-productivity 径向流radial system 富气enriched gas 贫气lean gas 气顶gas cap 气驱gas drive(or gas flooding)水驱water drive (or water flooding) 地层伤害formation damage 波及系数sweep efficiency 泄油半径drainage radius 基岩处理matrix treatment 单级脱气single stage separation泄油面积drainage area 表面张力surface tension 束缚力connate water(or interstitial water)石油钻井作业现场工作人员名称1 钻井队drilling crew 队、组crew、team2 技术员technician 钻井技术员drilling technician 泥浆技术员mud technician3 监督supervisor 钻井监督drilling supervisor 副监督assisstant supervisor地质监督geology supervisor4 工程师engineer 泥浆工程师mud engineer 泥浆工mudman机械工程师mechanic engineer 引擎、发动机engine 工程engineering钻井工程drilling engineering 采油工程production engineering石油工程petroleum engineering 试油工程oil test engineering拓展记忆---------------------------工作项目project 希望工程the hope project 三峡工程the Three-Gorge Project项目经理project manager 工程管理project management 钻工:roughneck、floorman司钻driller 副司钻assistant driller 钻井队长drilling foreman 钻井领班tool pusher井架工derrick man 发动机工,机工motorman 钻台工floorman机械师technicians,mechanic 电焊工welder 电工electrician 医生doctor材料员material man,staff man 炊事员cook 翻译interpreter, tansalator洗衣工laundry man石油作业现场常用工具石油作业现场普通工具扳手wrench 螺丝起子screwdriver 多角螺丝起子Phlilips screwdriver活动扳手monkey wrench,adjustable 钳子pliers 手斧hatchet 钩子hook 台钳bench vice 榔头hammer 木锤mallet 搬手spanner 锯子saw 电动手锯jigsaw 电锯power saw钢锯hacksaw 硬尺rule 软尺tape measure 砂纸sandpaper 油漆paint 油漆刷paintbrush 绝缘胶布electrical tape 电线wire 插头plug 电插座outlet 开关switch 螺栓bolt螺帽nut 钉子nail 电钻electric drill 钻头bit 工作台workbench 工具箱toolbox胶水glue 交棒glue bar 管钳pipe tongs,pipe spanner,wrench链钳chain tongs,chain spanner,chain wrench护丝thread protector,screw protector手轮hand wheel 阀门搬手valve wrench,valve spanner 链接法兰coupling flange安全带safety belt 安全帽safety cap 工作靴working boots 千斤顶jack 吊车crane拖拉机tractor 推土机dozer 刮刀scraper1、石油作业现场专业工具接头sub 配合接头X-over,cross-over 提升短接lifting sub,lifting nipple elevator卡瓦slip 母锥box bell 公锥taper tap 短节joint 柔性短节flex joint 井口wellhead螺旋钻铤spiral collar 方钻杆kelly 钻杆架pipe rack 材料房warehouse 绳卡guy anchor 润滑器lubricator 维护保养maintenance 内钳lead tong 外钳back-up tong液压大钳hydraulic tong 兜绳mule line 四通阀four-way valve 软管hose球阀ball valve, globe valve 闸板阀ram valve, gate valve 增压泵booster pump换配件fittings change 灌注泵charge pump第二章石油工程常用设备及专业术语第1节钻井设备部分1 井架derrick 塔形井架derrick A形井架cantilever mast,mast-A 桅杆mast底座大梁sill 架,台rack 架工操作台monkey-board2 游动系统travelling systemn 天车crown block 天车梁crown block beam游动滑车travelling block 钻井大绳drilling line, wire line 金属线, 电线wire,line钢丝绳,测井电缆wire line 金属线,电线wire,line 钢丝绳股strand 截断cutoff滑车,滑轮,皮带轮pulley 吊耳eye plate3 大钩与水龙头hook and swivel 顶驱top drive 大钩hook 大钩弹簧hook spring大钩销子hook pin 大钩环hook ring 大钩锁紧装置hook locking device大钩悬挂高度hook height 水龙头swivel 鹅颈管gooseneck 冲管wash pipe水龙头盘根swivel packing 钻井水龙带drilling hose,rotary hose,kelly hose 立管stand pipe 高压管线high pressure line 低压管线low pressure line 放压管线relief line储气筒gas holder,air holder4 转盘rotary table 转盘方瓦master bushing 方补心kelly drive bushing方孔square openning 小鼠洞mouse hole 大鼠洞rat hole (井架大门处)坡板ramp5 绞车drawworks,hoist 液压绞车hydraulically-powered winch 气动绞车air operated hoist 绞车hoist,windlass,drawworks 滚筒线轴卷轴reel pool drum滚筒高速气离合器drum high air clutch 滚筒低速气离合器drum low high clutch猫头cathead 液压猫头hydraulic cathead 上扣猫头make up cathead卸扣猫头make out cathead 牙嵌离合器jaw clutch 应急牙嵌离合器emergency jaw clutch涡磁刹车eddy current brake 猫头轴cathead shaft 猫头绳cathead line猫头绳爪cat line grip 死绳dead line 死绳固定器deadline anchor死绳固定器膜片dead line diaphragm 上扣spin up,screw on 卸扣,卸开break out, screw off 上紧,固定tighten 松开,松扣loosen 加载load 卸载unload 拧紧screw 拧松unscrew 刹者brake 刹车总成brake assembly 刹车轴brake axle,brake shaft 刹车带brake band刹车片brake band lining 刹车杆brake bar 闸瓦brake block 刹把break crank,brake bar刹车鼓brake drum 离合器clutch 液压油箱hydraulic reservoir液动试压泵hydraulic test pump 液压大钳hydraulic tong 倒档齿轮reverse gear第2节钻井泵类及相关设备泥浆泵mud pump,drilling pump,slush pump 活塞piston 活塞杆piston rod活塞皮瓦piston cup 缸套liner,pumpliner 凡尔体valve body 凡尔座valve cup阀弹簧valve spring 阀杆valve lever 阀面valve face 阀帽valve bonnet泥浆泵安全阀mud relief valve 排出阀discharge valve 吸入阀suction valve潜水泵submersible pump 阀门valve 阀盖valve cap 阀座valve seat 回压阀回压阀back pressure valve 单向阀check valve single-pass valve 安全阀safety valve手动阀manual valve 液动阀hydraulic valve 冷缸cold cylinder 拉杆tie rod,tension bear 上水头intake,suction end 排出口discharge spout 高压管high pressure压力表pressure gauge 冲数strokes 排量displacement,discharge capacity,flow rate第3节井下泵类及相关设备泵筒pump barrel 柱塞plunger 关闭shut down 尾管tail pipe 抽油杆sucker rod长冲程long stroke 低泵速small pumping speed 泵充满度the fullness efficient of the pump 抽油杆sucker rod 排气方法gas bleeding method 泵效pump efficiency三维空间three dimensional space 有效生举efficient lift for the deviated抽油杆扶正工具sucker rod centralization tools 严重的管杆偏磨serious string partial wear游动阀the travelling valve 固定阀the standing valve 部分磨损、偏磨partial wear无杆泵rodless pump 小泵深抽small pump deep pumping technology挂泵深度pump setting depth 尾管长度length of liner 管柱结构the structure of pipe string防脱器dropout-prevent device 井斜角hole angle 电热杆borehole electric heating rod稠油开采heavy oil production 空心杆热载体hollow sucker rod heat carrier变扣器方补芯bushing 终端器terminal assembly 空心抽油杆hollow sucker rod整体电缆传感器continuous cable,sensor 空心光杆hollow polish rod 悬挂器hanger防喷盒stuffing box第4节采油设备采油树Christmas tree 抽油机pumping unit 往复运动reciprocating motion泵杆pumping rod 机械传动mechanical transmission 载荷能力peak polish rod load系统效率system efficiency 冲程stroke length 冲次frequency of stroke无级可调smooth regulation 沉降式抽油泵the sinking sand pump 泵下沉砂sinking砂颗粒sand particles 胶质沥青gum asphalt含蜡量paraffin content 凝固点solidification point 热流hot fluid 参水mingle water第5节与泵操作有关的使用短语没有压力no pressure 压力过高the pressure is too high 返回太少mud return is few水太少water is little 抢修rush to repair 请看记录please read the record没作记录no record 加化学小品put in chemicals 加高岭土粉put in koaline powder加云母片put in mica sheet 加增粘剂put in viscosifier 加稀释剂put in diluent(thinner)加稳定剂put in stabilizer(stabilizing agent)加烧碱put in caustic soda测定比重measure gravity,gravity test 测定失水test filtration 测定切力measure force开关switch 停泵stop the pump 请打手势please make a gesture转动一周turn round a circle 垫高一些put something under it to raise 抓紧firmly grasp抬高lift it up 拿稳hold firm 打一下strike once 往下拉pull out站稳stand firm take a firm hand 小端small end 大端large end 光滑smooth粗糙rough,coarse 平面plane,flat 弯曲winding,bending 放松loosen绷直stretch tight,draw tight 撬棍pinch bar,pry bar 充氨气nitrogen aeration 气包snubber 冷却cooling 润滑lubricate 过载overload 功率不足inadequate power,power is not enough第6节钻台与底座钻台drilling floor,derrick floor,rig floor 钻井记录drilling record司钻监视器driller’s monitor 司钻控制台driller’s console 指重表weight indicator转盘rotary table 卡瓦slip 吊卡latch elevator 底座substructure 井队活动房bunkhouse 钻台上值班房doghouse 立根盒setback (place)立根盒容量setback capacity井控设备well-control device第7节防喷器万能防喷器versatile blowout preventerBag type BOP单闸板防喷器single ram preventer 双闸板防喷器double ram preventer 闸板pipe ram全封闭式防喷器blind ram 蓄能器energy accumulator 压井管线kill line 入口inlet出口outlet 演习drill 消防演习fire drill 防喷演习BOP drill防腐涂料油管anti-corrosion coating material tubing 多功能管柱multi-function string第三章钻井工程作业部分第1节钻井事故泄漏leak 漏失fluid loss 出砂sand production 井喷blow out 井涌kick,flow off井漏lost of circulation,circulation lost坍塌,井壁坍塌caving,cave in,collapse出砂sand production,sand flow 桥塞bridge plug 砂桥sand bridge 井堵well clogging卡钻sticking 卡钻杆sticking the pipe 卡钻具sticking the drill stem 打捞fishing打捞工作fishing job 侧钻side-tracking 侧钻井眼sidetracking hole水泥窜槽cement channeling 固井失败cement failure 防砂sand control,sand-proof第2节钻头牙轮钻头rock bit,tooth-wheel bit 刮刀钻头drag bit 金刚石钻头diomand bit镶齿钻头tungsten carbide bit,insert bit 喷射钻头jet bit 铣齿钻头milled bit 牙轮cone钻头装卸器bit breaker 钻头直径bit diameter 钻头寿命bit life 钻头规格bit gauge钻头磨损bit wear 钻头型号bit type 水眼尺寸nozzle size 水眼效率nozzle efficiency钻头接头bit sub第3节钻具方钻杆kelly 方钻杆旋转短节kelly spinner 方钻杆考克(旋塞)kelly cock 接头sub钻头接头bit sub 钻具drill stem,drilling string 钻杆drill pipe 管子tube,pipe钻具组合drilling assembly 扶正器stabilizer,centering guide 翼状扶正器wing stabilizer扩眼器reamer drill collar 无磁钻铤drill collar 加重钻杆heavy weight drill pipe近钻头扶正器near-bit stabilizer 绕性接头flexible joint 震击器jar 减震器shock absorber 螺旋钻铤spiral drill collar 键槽破坏器key seat reamer 安全接头safety joint钻杆刮泥器drill pipe wiper 配合接头crossover sub 减震器shock sub井下钻具组合BHA-bottom hole assembly泥浆动力钻具mud motor 管线tubeline 钻柱drill string 涡轮tubine涡轮钻具turbo-drill stem 斜度taper,slope 塔式钻具tapered drill stem 接头 a joint,sub 管接头a joint of pipe 立根stand,a stand,thribble 加厚upset 内加厚internal upset外加厚external upset 内外加厚internal-external upset 丝扣thread 母扣box 公扣pin左旋螺纹left-hand thread 右旋螺纹right-hand thread 正规接头regular joint贯眼接头full hole joint 内平接头internal flush joint 护丝thread protector丝扣油thread dope,thread oil 打捞篮junk basket 打捞工具fishing tool打捞管柱fishing string 打捞公锥fishing nipple 打捞颈fishing neck 打捞头fishing head 打捞作业fishing operation 打捞母锥fishing socket 牙轮打捞器cone fisher倒扣工具reversing tool 卡瓦打捞筒slip socket 铣鞋milling shoe 铣具milling tool平底铣鞋flat bottom mill 磁力打捞工具magnetic fishing tool 套管打捞矛casing spear打捞矛fishing spear 打捞钩fish hook 套管打捞筒casing bowl 动力扳手power wrench动力大钳power tong 大钳活动牙块hinged jaw 大钳锁销latch 大钳悬臂suspension unit 气动工具pneumatic tool 打捞震击器fishing jars 打捞缓冲器fishing bumper sub打捞环die collar 打捞筒overshot 打捞短节junk sub 卡瓦slips 刮井器scatcher刮眼器扩井器wiper 油位检查丝堵oil lever check plug 油位oil lever油尺oil-lever dipstick 加油孔lubrication hole 盘根盒stuffing box 井筒工具well bore tool 配套工具matching tools 滚轮扶正器idler wheel centralizer 减磨短节friction reduction sub 轴线加压hydraulic thruster 扶正器centralizer 防脱器、装置anti-slip device减磨扭矩接箍torque-reduction sub 减扭接头torque reduction sub轴向水力加压工具hydraulic thruster 下套管漂浮接箍casing floating coupling轴向加压器hydraulic thruster第4节钻井工程地面作业实用词汇与短语方入kelly-in 方余kelly-up 开钻spud in,starting drilling 作业指令working instruction起钻POOH=pull out of the hole 下钻run in the hole 起下钻make a trip 短起下钻short trip 通井wiper trip 起下循环一周round a trip 循环时间round time,circulating time换钻头change bit 甩钻具laydown 填井pack-hole封井packed drilling发生故障break down 接单根connection 放卡瓦set slip,setting slip,起卡瓦pull slip扩眼openning 划眼reaming 二层台double monkey board,runround 顶部驱动器top drive 吊环bail 吊卡elevator 安全卡瓦safety slips 接头sub adapter 短节sub substitute井下震击器downhole(bumper)jar,down well shaker 打捞工具fishing tool三片卡瓦three slips,three pieces 补芯bushing 方补芯kelly drive bushings转盘补芯(大方瓦)rotary drive bushing 转盘刹车rotary brake 丝扣油thread lubricant oil 刹把brake crank,brake bar,brake lever 脚踏开关pedal switch 挂档put into gear拉猫头cathead 内钳back-up tongs 外钳lead tongs 气动大钳pneumatic tongs 液压大钳hydraulic tongs 机械手mechanical arm 铁钻工machine hand 司钻房driller room有故障it has broken down, it has something wrong 已修好the breakdown has been fixed马上去go there at once 请下去please go down 请上来please come up躲开,危险get out,danger 请翻译来ask the interpretor to come here 冲洗flushing井口well-head(well head)井下落物fish 一根钻杆(单根)single(pipe)三根钻杆组合(立根)thribble 甩单根breaking down 接单根make a connection气动绞车pneumatic drawworks 吊篮basket 卡子clamp 绳套rope sling loosening紧固tightening 挪开move it off 换班change,shift 保养设备maintain equipment钻井日志boring journal,boring log 油管悬挂器tubing hanger第5节钻井工程井口作业实用词汇与短语喇叭口bell mouth,flare opening 贮能器accumulater 液压阀hydraulic valve液压管hydraulic hose 阻流管choke line 井控管汇well control manifold泄压阀pressure relief valve 调压针阀pressure regulating needle valve回压阀backpressure valve 井口螺丝the bolt of wellhead 井口绞车well head drawworks水刹车water brake,hydraulic brake 电缆(electric)cable 井口压力wellhead pressure隔水导管conductor riser 小心滑倒Guard against slipping 不要掉下去Take care not to fall down 我来清理let me clean up 带把扳手来bring a spanner,please 带把铁锤来bring a hammer,please. 带点密封剂bring a little sealant,please 带个密封圈bring a sealing washer 用起子撬prize with (using)screwdriver 用手推注push by hand 卸下来了it has been removed off 装配好了it has been assembled 很快就好了it will be finished right away抬一下let’s lift it 上紧螺丝tighten the screw loosen 松开螺丝loosen the screw把绳子给我give me the rope,please 把绳子拿走take the rope away。

石油钻井工程现场常用专业英语词汇

石油钻井工程现场常用专业英语词汇

1. DRILLING ENGINEERING 钻井工程1.1 THE COMPENTS OF THE ROTARY DRILLING RIG钻机系统的组成1.1.1 Hoisting System 提升系统sub structure 井架底座,底部结构derrick (mask) 井架crown block 天车traveling block 游动滑车wire line (drill line) 钢丝绳,钻井大绳deadline 死绳air hoist 气压提升机,气压提升绞车drilling rig (drilling machine) 钻机drawwork 绞车drum 滚筒brake crank (handle, bar) 刹把hydraulic brake 水刹车electric brake 电磁刹车mechanical friction device 机械磨擦装置cathead 猫头elevator 吊卡slip type casing elevator 卡瓦型套管吊卡pipe elevator 钻杆吊卡slip 卡瓦safety slip 安全卡瓦collar rotary slip 环形钻铤转盘卡瓦drill pipe rotary slips 环形钻杆转盘卡瓦links 连杆hook 大钩hook load 大钩负荷hook speed 大钩速度hook weight 大钩悬重DF (drill floor) 钻台monkey board 二层台1.1.2 Circulating & Solids Control System 循环及固控系统drilling mud (drilling fluid) 钻井泥浆,钻井液water mud 淡水泥浆water-base mud 水基泥浆salt mud 盐水泥浆salt-base mud 盐水基泥浆oil-base mud 油基泥浆oilemuision 油包水泥浆,石油乳浊液mud property 泥浆性能mud weight out/in 泥浆密度进/出mud density out/in 泥浆密度进/出mud viscosity 泥浆粘度mud conductivity 泥浆电导率mud resistivity 泥浆电阻PH-value PH值water loss 失水sand content 含砂量gel strength 静切力mud cake 泥饼mud cake effect 泥饼效应mud filtrate 泥浆滤液mud loss 泥浆漏失mud column 泥浆液柱mud sample 泥浆试样mud stability 泥浆稳定性mud pump (pump) 泥浆泵pump body 泵体pump capacity (discharge) 泵排量(泵容量)pump displacement 泵排量pump output 泵排量pump efficiency 泵效率pump stroke 泵冲程pump cylinder 缸套mud pump rod 泥浆泵拉杆piston 活塞mud room 泵房mud line 泥浆管线choke line 地面管汇high pressure line 高压管线standpipe 立管standpipe valve 立管闸门hose 水龙带swivel 水龙头swivel bail 水龙头吊环swivel sub (joint) 水龙头接头swivel stem 水龙头中心管gooseneck 鹅颈管wash pipe 冲管wash pipe swivel 冲管旋转接头kelly 方钻杆kelly cock 方钻杆上旋塞kelly dog nut 方钻杆下旋塞HWDP height weight drillpipe 加重钻杆DP drillpipe 钻杆DC drill collar 钻铤spiral collar 螺旋钻铤pony DC (collar) 短钻铤NMDC non-monel collar 无磁钻铤tool joint 钻具接头sub (joint) 接头tool joint box 接头母扣tool joint pin 接头公扣X-O (crossover) subs 配合接头(转换接头)shock sub 减震接头bumper sub 缓冲器接头bit sub 钻头接头dart sub 投入式止回阀阀座flex sub 柔性短接string stabilizer (pin ×box) 钻具扶正器(公扣对母扣)near bit stabilizer (box ×box) 扶正器(母扣对母扣)centrallizer 扶正器bumpers (shock absorber) 减震器drilling junk basket 随钻打捞杯drilling jar 随钻震击器jar 震击器BHA bottomhole assembly 下部钻具总成HDRT high data rate tool 高速数据传输钻具(MWD用)drill stem (drill string) 钻柱bit 钻头drag bit (blade bit) 刮刀钻头cone bit (roller bit) 牙轮钻头tri-cone bit 三牙轮钻头jet bit 喷射式牙轮钻头core drilling bit 取心钻头milled tooth bit 铣齿钻头insert bit 镶齿钻头gauge insert bit 保径镶齿钻头diamond bit 金刚石钻头bit cone 钻头牙轮bit size 钻头尺寸bit cost 钻头成本bit record 钻头记录bit type 钻头类型bit jets 钻头水眼bit nozzle 钻头喷嘴TFA total flow area 钻头水眼总流量面积bit consumption 钻头用量bit footage 钻头进尺bit factor 钻头因素bit grading 钻头磨损等级bit-tooth dullness 钻头牙齿磨钝程度bit life 钻头寿命bit HHP hydraulic horsepower 钻头水马力hole opener 扩眼器underreamer 管下扩眼器annular 环空wellhead 井口flowline 架空管线shale shaker 震动筛mud tank (mud pits) 泥浆罐suction pit 进口罐setting pit 沉砂罐waste pit 泥浆坑desander 除砂器desilter 除泥器degasser 除气器mud cleaner 清洁器centrifuge 离心机agitator 搅拌机1.1.3 Rotary System 旋转系统prime mover 原动机diesel engine 柴油机engine 引擎rotary table 转盘rotary base 转盘底座rotary chain 转盘传动链条KB kelly bushing 方钻杆补心roller type bushing 滚子方补心master bushing 转盘补心slip type casing spider 卡瓦型套管卡盘tongs 大钳,吊钳lead tongs 内钳back-up tongs 外钳hydraulic tongs 液压大钳chain tongs 链钳pipe tongs (spanner) 管钳spinning chain 旋链power tongs 动力大钳spanning wrench 旋转扳手1.1.4 Blowout Prevention System 防喷系统kick 井涌blowout 井喷blowout control 井控blowout control equipment 井控设备blowout hookup 防喷装置BOP blowout prevention 防喷器annular ram prevention (万能)环形防喷器pipe rams (半封)闸板防喷器blind rams 盲板全封式防喷器shear rams 剪切闸板式全封防喷器blowout plug 防喷塞blowout preventer of three stage packer 三级密封式防喷器control console 控制台remote control console 远程控制台conductor line 导管choke line manifold 节流管线fill line 灌浆管线kill line 压井管线emergency line 紧急压井管线chokes 节流阀hydraulic valve 液压阀gas buster 泥气分离器poor boy 泥气分离器choke pressure 节流压力blowout prevention procedure 防喷措施1.1.5 Motion Compensation System 运动补偿系统offshore floating rigs 海上浮式钻机drillstring compensator 钻柱补偿器sea level 海平面sea floor 海底deck 甲板air pressure vessels 空气压力容器hydraulic cylinder assembles 液压缸总成piston rod 活塞杆standard hook assembles 标准大钩总成riser 隔水导管guideline tensioner 导索拉紧装置control panel 控制盘guide base 导引底盘marine riser 海中隔水导管moon pool 月形开口riser tensioner 隔水导管拉紧装置1.2 W ELLS & DRILLING CRAFT 井与钻井工艺流程well, drilling well 井,钻井wildcat well 预探,初探井delineation well 探边井development well 生产井,开发井satellite well 丛式井injection well 注水井direction well 定向井deviation well 斜井COST continental offshore stratigraphic test well(美)大陆近海地层探井to rig up 安装(钻机)to install the equipment 安装设备to get drill pipes in order 排钻具to measure & inspect drillstring 仗量,检查钻具to measure the length of drill pipes &drill collars 量钻杆,量钻铤to nipple up BOP 装封井器to spud in 开钻to turn on the pumps 开泵to circulate, circulation 循环circulate to the bottom up 完全循环reserve circulation 反循环bit break-in procedure 磨合钻头reaming 扩眼drilling 钻进coring drilling 取心钻进rough drilling (bouncing of drilling tool) 跳钻bit bouncing 蹩钻reverse rotation (running) 打倒车correct drift 纠斜lost circulation 井漏slough (cave-in) 井塌to stop the pump 停泵PC pipe connection 接单根make a joint 接单根wire line survey 吊测deviation survey 测斜to change the shaker screen 换筛布to repair the pump 修泵to break down a joint 卸一个单根to slug the pipe 往钻杆内打重泥浆POOH to pull out of hole 起钻to trip out the hole 起钻touch sticking 遇卡pulling a piston 拔活塞to lubricate rig (drawwork) 保养钻机(绞车)to repair rig 维修钻机to cut & slip the drillline 倒大绳to clean the mud tank 清罐well logging, E-log 电测SWC sidewall coring 井壁取心DST drill stem test 钻杆中途测试to running casing, casing 下套管surface casing 表层套管intermediate casing 技术套管liner 尾管to running cementing 固井to squeeze cement 挤水泥WOC wait on cement 侯凝to nipple up BOP 换装封井器to install the BOP 装封井器to test BOP 封井器试压to change bit, bit change 换钻头RIH run in hole 下钻to trip in 下钻touchdown, touching resistance 遇阻RTO round trip operation 起下钻作业short tripping 短起下钻reaming 划眼to cement plug , plug back 打水泥塞side tracking 侧钻to kick off 造斜KOD kick off depth 造斜深度KOP kick off point 造斜点to hang up 意外停机to survey the flowout 监测溢流flow check 溢流检查WOO wait on order 等指令WOW wait on weather 等天气WOL wait on logging 等测井WOE wait on equipment 等设备WOFT wait on fishing tools 等打捞工具to finish drilling 完钻to running the liner 挂尾管to plug-back 填井final testing 完井测试to install the Chirstmas tree (production) 装采油树well completion 完井to prevent sticking 防卡to prevent caving 防塌to prevent loss of circulation 防漏to prevent blowout 防喷1.3 SPECIAL ENGINEERING OPERATION 特殊工程施工1.3.1 Coring 取心1.3.1.1 Coring Equipment 取心及岩心分析设备coring drill 取心钻具core drilling bit 取心钻头core bit 取心钻头coring crown 金刚石取心钻头core cone bit 牙轮取心钻头core basket 岩心爪core barrel catcher 岩心抓取器core catcher 岩心爪core catcher case 岩心爪外套core gripper 岩心爪core-gripper with slip 卡瓦式岩心爪core-gripper with slipcollar 卡箍式岩心爪core-gripper with slipspring 卡簧式岩心爪core spring 岩心卡簧core barrel 岩心筒core container 内岩心筒core chamber 岩心室core barrel head 岩心筒上盖core barrel ring 取心筒垫圈core shoe (压力式)取心筒鞋core plunger 岩心推取杆core pusher 岩心推取塞core fisher 井底岩心打捞器core picker 落井岩心打捞器core bag 岩心袋core box 岩心盒core tray 岩心盒core house 岩心存储室core storage 岩心库core library 岩心库core breaker 岩心切断器core slicer (splitter) 岩心切断器core-drying oven 岩心烘箱core cutter 岩心切片机core distillation apparatus 岩心蒸馏仪core interpreting device 岩心分析仪core laboratory 岩心分析实验室1.3.1.2 Core Drilling Operation 取心钻进作业core hole 取心井core boring 取心钻进core drilling 取心钻进cored-up mould 岩心造型coring depth 取心井深coring footage (run) 取心进尺coring weight 取心钻压coring formation 取心地层core grouting 取心被卡core breaking 割断岩心core breaking by hydraulic pressure 投球液压割心core breaking by mechanical loading 机械加压割心1.3.1.3 Core Analysis 岩心分析core-analysis data 岩心分析数据core data 岩心数据core log 岩心录井core graph 岩心图core cross section 岩心横剖面core-description graph 岩心描述图core sample 岩心样core wafer 岩心薄片core size 岩心尺寸core orientation 岩心方向core inlet face 岩心入口面core outlet face 岩心出口面core diameter 岩心直径core factor 岩心系数core grinding 岩心磨削core wash 岩心冲蚀core intervals 取心井段core footage (run) 取心进尺core recovery 岩心收获率core porosity 岩心空隙度core oil saturation 岩心含油饱和度core permeability 岩心渗透率1.3.2 Directional Well Drilling & Deviation Survey 定向钻井和井斜监测directional well 定向井directional hole 定向井directional drilling 定向钻井directional drilling contractor 定向井承包商directional MWD 定向随钻测量directional drill tool 定向钻井工具directional orientation tool 定向工具the steering tool 定向工具deflecting tool 造斜工具directional-survey tool 定向测量工具direction finder 测向仪direction instrument 方向仪directional tool (steering tool) 随钻测斜仪inclinometer 测斜仪single shot inclinometer 单点测斜仪syphon inclinometer 虹吸测斜仪continuous inclinometer 连续测斜仪gyroscope 陀螺仪pendulums (plumb bob) 测棰magnetic compass 磁螺盘directional turbodrill 定向涡轮钻具directional bit 定向钻头directional-type tricone bit 定向三牙轮钻头directional clinograph 方位测斜仪deviation replot 井斜图side track 定向设计剖面图horiz projection 水平投影图vertical projection 垂直投影图projection on a vertical plane 垂直面上的投影图deviation map 井斜图perspective view 透视图3 dimensions visualisation 三维空间透视图directional diagram 方位图deviation report 井斜报告directional data 井斜数据surveys 井斜数据deviation measurement data 井斜测量数据directional line 方向线main direction 主方向E.W.S.N 东,西,南,北directional control 方位控制directional characteristics 方位特征directional accuracy 方向性精度directional elements 定向要素direction parameter 方位参数horizontal plane 水平面vertical plane 垂直面directional angle 方位角the drift angle 井斜角the azimuth 方位角bearing (north) 方位角angle of projection 投影角desired drift angle 设计的造斜角the bottom hole coordinate 井底坐标coarse coordinates 水平位移坐标the vertical depth 垂直深度KOD kick off depth 造斜深度end off deviation vertical depth 稳斜结束时的垂直深度end kick off vertical depth 结束造斜时的垂直深度final re-entry depth 恢复点的深度average angle method 平均角度法radius of curvature method 曲率半径法KOP kick off point 初试造斜点end of kick off 造斜终点end of deviation 斜井段终点re-entry point 返直点dog leg 井斜度,狗腿角dog leg scale 狗腿度比例dog leg severity 狗腿严重程度angle build up 增斜angle drop off 降斜dog leg at kick off point 增斜率dog leg at re-entry point 降斜率the actual well path 井眼轨迹1.3.3 Casing 下套管casing 套管casing joint 套管单根,一节套管casing starter 入井第一节套管casing nipple 套管短节casing string 套管柱casing tally 套管记录casing type 套管类型casing weight 套管重量casing size 套管尺寸casing diameter 套管直径casing length 套管长度casing volume 套管容积casing grade 套管钢级casing depth 套管深度casing setting depth 套管下入深度casing accessories (hardware) 套管附件casing guide shoe 引鞋casing float shoe 套管鞋casing shoe depth 套管鞋深度casing centralizer 套管扶正器casing collar 套管接箍casing check valve 回压凡儿casing float (collar) 回压凡儿casing sub 套管异径接头casing head 套管头casinghead spool 套管头四通casing landing 联顶节casing job 下套管作业casing running(installation) 下套管casing-bearing formation好套管下入地层casing appliances 下套管工具casing connection 套管连接casing elevator 套管吊卡casing slip 套管卡瓦casing spider 套管卡盘式吊卡casing suspender 套管悬挂器casing hanger 套管悬挂器casing screw protector 套管公扣护丝casing screw head 套管母扣护丝casing seal 套管密封件casing annular 套管环空casing-to-hole annular 套管井壁环空casing pressure 套管压力casing head pressure 套管头压力casing pressure test 套管试压casingless completion 裸眼完井casing inspection 套管探伤casing programme 套管程序casing severing 割套管casing sticking 套管被卡casing wear 套管磨损casing split 套管裂纹casing leak 套管漏casing imperfection 套管缺陷casing failure 套管损坏casing damage 套管损伤casing deformation 套管变形casing corrosion 套管腐蚀casing collapse 套管挤坏casing buckling 套管弯曲casing bridge plug 套管桥塞casing bowl 套管打捞筒casing collar location 套管接箍测定器casing corrosion monitoring 套管腐蚀监测casing knife 套管割刀casing mandrel 胀管器casing mill 套管铣鞋casing packer 套管封隔器casing perforator 套管射孔器casing section mill 套管铣刀casing splitter 套管割刀casing withdrawal 拔套管1.3.4 Well Cementing 固井open hole 裸眼井cased hole 套管井pocket 口袋the pocket volume 口袋体积normal volume 正常体积extra volume 额外体积hole description 井眼描述string / casing description 钻柱和套管描述surface cement line description 地面水泥管线描述cement 水泥number of sacks 水泥袋数cement factor 水泥系数volume of the cement 水泥体积cement mark 水泥标号cement brand 水泥牌号cement filtrate 水泥滤液cement slurry 水泥浆cement paste 水泥浆cement milk 水泥浆slurry in string 钻柱内水泥浆cement slurry volume 水泥浆体积(用量)slurry excess 水泥浆余量slurry density 水泥浆密度cement column 水泥浆液柱cement consistency 水泥浆稠度cement flow 水泥浆液流cement additive 水泥添加剂additive name 添加剂名称bentonite 膨润土additive volume 添加物体积cementer 粘结剂cement accelerator 水泥促凝剂cement hardener 水泥速凝剂cement agent 粘结剂cement concrete 水泥混凝土cement-water ratio 水灰比cement operation (jobs) 固井作业cement method 固井方法first stage cementation 一级注水泥two stage cementation 二级注水泥multi-stage cementation 多级注水泥liner cementation 衬管注水泥cement equipment (unit) 固井设备cementing tool 固井工具cementing pump 固井泵cementing pump skid 撬装注水泥泵组cementing tank 水泥罐cement blender 水泥搅拌器cement mixer 水泥搅拌器cement practice 固井施工cement squeeze work 挤水泥作业cementing formulation 注水泥配方cement point 封固段cementing through 全井封固seal liquid (spacer fluid) injection 注隔离液cementing injection 注水泥浆chasing 替浆cement displacement 替浆cementing reaction 胶结反应cement setting 水泥凝固cement curing time 水泥候凝时间cementing strength 水泥强度cemented up 注完水泥cement basket 水泥伞cement casing head 水泥头cement mantle 水泥环cement plug 水泥塞cement sheath 水泥壳cement evalution log 固井质量评价测井cement needle 凝固强度检测针cement top 水泥顶界cement thickness 水泥环厚度cement bond log 水泥胶结情况测井cement bond 水泥胶结cementation factor (exponent) 胶结系数cement-formation interface 水泥-地层界面cement job quality 固井质量cement failure 固井不合格cement cap 悬空水泥塞cement channeling 水泥串槽cement contamination 水泥侵cement cut 泥浆水泥侵cement dehydration 水泥浆脱水1.4 THE APPLICATION PROGRAM OF ENGINEERING PARAMETERS工程参数应用程序1.4.1 BIT 钻头initialize run 钻头初始化运行new bit initialization 新钻头初始化bit report 钻头报告bit cost report 钻头成本报告drilling data 钻进数据报告well string data 钻具数据BHA bottom hole assembly 下部钻具组合bit list 钻头列表the bit general data 钻头一般参数bit performance 钻头性能bit characteristics 钻头特征bit number 钻头编号the last drilled bit 上一个钻头bit type 钻头类型drilling cost 钻进成本rig cost 钻机作业成本final cost on drilling time 钻进时间里最终钻头成本final cost on time in hole 钻头入井最终成本minimum bit cost 最小钻头成本FFA total flow area 钻头总截流面积nozzle’s area 水眼尺寸nozzle efficiency 水眼效率bit run , footage 钻头进尺bit progress, run length 钻头进尺individual bit run 单个钻头进尺depth interval 井段,井深间隔average over the run 钻头平均运行参数expected run 钻头预计进尺drilling time 钻进时间off-bottom time 钻头提离井底时间the final wear 钻头最终磨损total revolutions 钻头总旋转圈数the bit manufacture 钻头制造商1.4.2 HYDRAULICS REPORT 水力学报告hydraulics computation 水力学计算Bingham formula 宾汉公式power law formula 幂次律公式power law exponent 幂律指数Reynold’s number 雷诺数the friction factor 磨擦系数the mud system 泥浆系统mud system parameter 泥浆系统参数mud name 泥浆名称flow out 泥浆出口流量computed flow 计算流量measured flow 测量流量critical flow 临界流量optimize flow 优化流量mud density 泥浆密度the equivalent mud density 当量泥浆密度PV plastics viscosity 塑性粘度YP yield point 屈服点GEL strength 静切力MW mud specific weight 泥浆比重mud velocity 泥浆速度nozzles speed 水眼流速a critical velocity 临界流速the actual velocity 实际流速rheological model 流变模型rheological equation 流变方程flow behavior 流性flow type 流动类型laminar flow 层流turbulent flow 紊流Binghamien fluid 宾汉流体Newonient fluid 牛顿流体Pseudo-plastic fluids of Ostwold 奥式假塑性流体the shear stress 切应力the shear rate 切率consistency index 稠度系统a hole cleaning efficiency 井眼净化程度pressure losses 压力损失annular pressure losses 环空压力损失total presses losses 总压力损失pressures losses of laminar flow 层流压力损失pressures losses of turbulent flow 紊流压力损失surge and swab pressure 抽吸和冲击压力bit hydraulic horsepower 钻头水马力mud lag time 泥浆迟到时间cuttings lag time 岩屑迟到时间cuttings size 岩屑尺寸cuttings density 岩屑密度cuttings removal 岩屑上返the slip velocity of cuttings 岩屑下滑速度the relative slip velocity 相对滑动速度drag coefficient 牵引系数annular parameter 环空参数well hole and string parameter 井眼和钻具参数VAN volume of annular 环空体积open hole 裸眼段casing 套管段liner 尾管段FANN graph 范氏图1.4.3 KICK CONTROL 井控,压井well kick , well blowout 井涌,井喷the origin of a kick 井涌起因formation pressure 地层压力the mud column pressure 泥浆液柱压力the invading fluid 地层侵入流体the influx fluid 侵入井眼的流体circulating pressure 循环压力kick report 井涌报告,压井报告initial data 原始数据circulating data 循环数据killing of a well 压井driller’s method 司钻法压井balance bottom hole pressure method 平衡井底压力法压井kick killing data 压井数据the depth of the kick 井涌出现的井深kick size 井涌体积kick tolerance 井涌极限influx density 侵入液密度numbers of circulation cycles 循环周期数the initial mud weight 初始泥浆密度the required mud weight (density) 压井所需泥浆密度resulting mud weight 最终泥浆密度baryte density 重晶石比重heavy mud density 重泥浆密度the adding products 加重材料,添加材料adding rate 加重速度available quantity 储备量,available volume 可使用的体积slow pump stroke 低泵速泵冲the shut in drill pipe pressure 关井钻杆内压力well head maximum working pressure 井口最大工作压力casing burst pressure 套管崩环压力the minimum formation fracturation pressure 最小地层破裂压力expected surface pressure 预期地层压力initial circulating pressure 初始循环压力final circulating pressure 最终循环压力the maximum allowable surface pressure 最大允许地面压力hydrostatic pressure inside pipe 钻杆内静水压力casing pressure 套管压力initial bubble pressure 初始冒泡压力shoe pressure 套管鞋压力displaced volume 排液体积the trip margin 起下钻边界1.4.4 OPTIMIZATION DRILLING 优化钻井WOB weight on bit 钻压RPM the rotation speed 转速the drilling rate 钻进速度the same type of formation 同类型地层a lithological change 岩性变化formation abrasiveness 地层研磨性参数abrasive formation (layer) 研磨性地层drillability factor 可钻性因素formation drillability factor 地层可钻性因素reliable field data 可靠的现场数据the lowest drilling cost 最低钻井成本five-spot drill-off test 五点钻速法optimum WOB 优化钻压值bit weight exponent 钻压指数optimum RPM 优化转速值expected footage 预期进尺expected rate 预期钻速zero drilling rate 零点钻速initial rate of penetration 初始钻速average rate of penetration 平均钻速expected rotating time 预期钻头旋转时间normalized bit tooth height 标准的钻头牙齿高度tooth wear rate 钻头牙齿磨损速度tooth dull 钻头牙齿钝化程度tooth wear 钻头牙齿磨损值bit bearing life 钻头轴承寿命bearing dull 钻头轴承钝化程度the normalized bearing wear 校正的钻头轴承磨损值bit exponent 钻头指数rotating time 钻头旋转时间total rotating hours 总旋转小时数round trip time 起下钻时间bit starting depth 钻头启用井深the optimum parameter 优选参数IDAC code international association of drilling contractors国际钻井承包商协会钻头编号1.5 DRILLING TROUBLES & FISHING 钻井复杂情况与打捞lost circulation, mud loss 井漏,循环漏失kick, gas kick, well kick 井涌well blowout 井喷well slough (cave-in) 井塌drilling string not well braked 溜钻percussion drill 顿钻damaged bit 钻头损坏broken teeth 断牙齿lost nozzle 掉水眼lost cone 掉牙轮lost bit 掉钻头bit balling, balling up of a bit 钻头泥包drilling pipe breaking 断钻具touchdown, touching resistance 遇阻touch sticking 遇卡stuck (sticking) 卡钻drill pipe sticking, sticking of tool 卡钻differential sticking, wall sticking 粘卡key-seating sticking 键槽卡钻sand bridge sticking 砂桥卡钻sand settling sticking 沉砂卡钻fishing tool & process agent 打捞工具releasing stuck agent, 解卡剂black magic, pipe lax 解卡剂sticking point instrument 卡点测定仪plugging agent, sealing agent 堵漏剂lost circulation additive (material) 堵漏添加剂,堵漏材料heavy weight additive 加重剂weighting material 加重物weighted mud 加重泥浆chemical cutter 化学切割器drill pipe cutter 钻杆外切割器casing cutte 套管内切割器washover backoff connector tool 套铣倒扣工具overshot, bell socket 卡瓦打捞筒washover pipe 套铣筒washover shoe 套铣鞋reverse circulating basket 反循环打捞篮drilling junk basket 随钻打捞篮catchall (junk catcher) 一把抓fishing tap 公锥box tap 母锥milling taper 铣锥mill (milling) shoe 铣鞋mill shoe 磨鞋impression block 铅印trip spear (bulldog) 打捞矛wireline spear 电缆打捞矛bend drill pipe 弯钻杆fishing magnet 强磁打捞器key seat wiper 键槽清除器key seat reamer 键槽扩大器stabbing guide 对扣引鞋fishing & other operation 打捞和其它作业to soak with black magic 泡解卡剂breakouting pack of dynamic 爆破松扣washover 套铣make-up (stab) 对扣thread making 造扣back-off 倒扣kill-job, well killing, well control 压井kill job 压井作业1.6 RIG TYPES & OTHER EQUIPMENTS ONWELLSITE钻机类型与其它井场设备1.6.1 Rig Types 钻机类型land, onshore 陆地,陆上swampy 沼泽地带shallow 泻湖区coastal area , offshore 沿海地区,海上drilling rig, drilling machine 钻机cable rig 顿钻钻机cable tool drilling unit 顿钻钻井设备mechanical drilling rig 机械钻机direct-current motor drive drilling rig 直流电动钻机onshore (land) rigs 陆上钻机offshore rigs 海上钻机drilling platform 钻井平台ODP offshore drilling platform 海上钻井平台Jack-up 自升式平台fixed platform 固定式平台SEMI-submersible 半潜式平台self-elevating drilling platform 自升式钻井平台self-elevating offshore drilling platform 自升式海上钻井平台piled steel platform 钢柱支撑平台gravity structure platform 重力结构平台drilling barge, barge 钻井驳船,驳船drillship 钻井船deck (main deck) 甲板,主甲板delipad (helideck) 直升机停机坪steel jacket 钢制导管架1.6.2 Other Equipment on Wellsite 井场其他设备the top drive unit 顶部驱动装置mouse hole 大鼠洞rathole 小鼠洞cellar 圆井pipe slacking block 钻杆盒driller’s console 司钻控制台drilling line reel, drum 大绳滚筒,滚筒the doghouse 钻台值班房,偏房the tool box (possum belly) 工具箱tools of wellhead 井口工具wrench 扳手B.O.P closing unit 封井器控制台wire line stand 大绳架catwalks 大门前跑道personal elevator 乘人电梯wellsite, drilling site 井场the drilling office 钻井办公室the company office 公司办公室pipe racks 钻杆架parts storage 配件房work shop 车工房tool house 工具房water tank 水罐trip tank 起下钻灌泥浆罐mud lab 泥浆房S.C.R house 可控硅房cable tray 电缆排cable elevator 电缆架generator house 发电房electric generator room 发电房gas flare 放喷管线点火处1.7 FIRE PROTECTION, SAFETY & ENVIRONMENTAL PROTECTION消防,安全与环保1.7.1Fire Protection 消防fire goods inflammables 易燃物inflammable material 易燃物explosive gas 易爆气fire damp 沼气gas, nature gas 煤气,天然气inflammable 易燃物品,易燃油品fired charge 引爆炸药fire alarm 火警fire alarm system 火灾报警系统fire detector 火灾探测器fire monitor 防火监控器fire safety system 防火安全系统fire control unit 消防设备fire control equipment 消防器材fire protection equipment 放火设备fire truck 消防车fire-entry suit 消防衣fire apparatus 灭火器fire extinguisher 灭火器fire extinguisher agent 灭火剂fire foam 灭火泡沫fire foam producing machine 泡沫灭火器fire escape 安全门fire exit 太平门fire door 防火门fire gate 放火闸fire ax 消防斧fire hydrant ,fire-plug, 消防栓fire bucket 消防桶fire bank 消防堤fire bulkhead 放火墙fire-fighting rack 消防梯fire sand 消防砂fire fighting boat 消防船fire boat 消防艇fire water line 消防供水管线fire department 消防局fire house 消防站fire brigade 消防队fire-fighting crew 消防队fire fighter , (fire man) 消防员fire patrolman 火灾巡警fireboss 瓦斯检验员firebug 纵火犯firer 放火者fire drill 消防演习fire control 防火fire failure 火灾事故fire hazard 火灾危险性fire insurance 火灾保险fire report 火灾报告fire performance 耐火性能fire resistance 耐火性fire resistance rating 耐火等级fire permit 用火许可证fire prevention code 防火法规1.7.2Safety 安全security 安全safe area 安全区safe atmosphere 安全空气环境safety operation area 安全工作区safe distance, safety clearance 安全距离safe allowance stress 安全许可最大应力safe bearing load 安全负荷safe concentration 安全浓度safety measure, safety precautions 安全措施safety code, safety regulation 安全规程safety guide 安全指南safety clause 保护条款safety guide procedure 防护措施safety-check, safety inspection 安全检查safety education 安全教育safety factor, coefficient 安全系数assurance coefficient 安全系数margin of safety 安全限度potential safety hazard 安全隐患safeguard procedure 防护措施safe rules 安全制度safe operation 安全操作safe practice 安全规章safety analysis technical 安全分析技术safety program 安全程序safety record 安全记录safety voltage 安全电压safety weight 安全重量safe working pressure 安全工作压力safety device , equipment 安全设备safety alarm device 安全报警设备safety checker, safety detector 安全检测器safety apparatus 保险装置safety appliance 防护用具safety grounding device 安全接地设备safety valve 安全阀safety sensor 安全传感器safety switch 安全开关safety belt, safety band 安全带,保险带safety-strap 保险带safety chain 安全链safety board 安全工作台safety cable 保险索safety shelf 安全架safety hat, safety helmet 安全帽protective cap 安全帽safety clothing 安全服safety goggles 护目镜safety shoes 安全鞋safety notice 安全标志safety color 安全色标safety flare 安全照明灯safety lamp 安全灯safety screen 安全罩safety lighting 安全照明safety fuse 安全保险丝1.7.3 Environmental Protection 环境保护environment 环境environmental aspectenvironmental analysis 环境分析environmental administration 环境管理environmental management 环境管理environmental change 环境变化environmental conditions 环境条件environmental criteria 环境标准environmental data 环境数据environmental parameter 环境参数environmental element 环境要素environmental factor 环境因素environmental patter 环境格局environmental effect, environmental impact 环境影响environmental degradation 环境质量下降environmental disruption 环境破坏environmental contamination 环境污染environmental pollution 环境污染waste water, devil water 废水exhaust gas, end gas, waste gas 废气waste product 废物waste liquid, devil liquor 废液off-scum, waste slag 废渣ambient noise 环境噪音environmental extreme 恶劣环境environmental conservation 环境保护environmental control system 环境控制系统environmental control unit 环境控制装置environmental health 环境卫生environmental hazard 环境公害environmental noise 环境噪音environmental protection 环境保护environmental test 环境试验environmental monitoring 环境监测environmental survey 环境检测environmental reconstruction 环境改造environmental temperature 环境温度ambient temperature 环境温度environmental containment standard 环境标准。

石油钻井英语缩写及词汇

石油钻井英语缩写及词汇

石油钻井英语缩写及词汇石油钻井英语缩写及词汇DC: drill collar钻铤DP: drill pipe钻杆HWDP: heavy weight drill pipe加重钻杆X/O: crossover转换接头CSG: casing 套管WOC: wait on cementing侯凝POOH: put out of hole起钻(trip out)短起:short tripRIH: run in hole下钻(trip in)R/U: rig up组装N/U: nipple up组装L/D: lay down甩钻具DD:directional driller:定向司钻(斯伦贝谢的员工)w/: withBOP: blowout preventer防喷器、封井器BHA: bottom hole assembly井底钻具OD: outside diameter外径ID: inside diameter内径IF: internal flush内平FH: full hole贯眼EU: external upset外加厚IU: internal upset内加厚WBM: water base mud水基泥浆OBM: oil base mud油基泥浆TIW: Texas Iron Works全开安全阀MW: mud weight泥浆密度SPP: standpipe pressure立管压力MWD: measure while drilling随钻测量CCL: casing collar log套管接箍测井GR: gamma ray伽马(测井)HTHP: high temperature & high pressure高温高压RPM: round per minute转速SPM: stroke per minute泥浆泵TD: total depth总井深MD: measured depth斜深TVD: true vertical depth垂深PPG: pound per gallonRKB: rotary kelly bushing方钻杆补心GL: ground level地表LCM: loss circulation materials堵漏剂P/U: pick up上提WOB: weight on bit钻压VISC: viscosity泥浆粘度N/D: nipple down拆卸R/D: rig down拆卸SX: sacks袋、包BBL: barrel桶B/U: bottom up循环一周M/U: make up组装LB: poundPSI: pound per square inchESD: emergency shutdown紧急关停装置ROP: rate of penetration进尺速度(机械钻速)ESP:emergency response plan应急响应预案Isolation valve高低压闸门Swab 凡尔提(泥浆泵配件)Hub方卡瓦Bail 吊环Air hoist气葫芦Chain hoist手拉葫芦、倒链V-door (pipe ramp) 斜坡Flowline泥浆天槽Gas buster / poor boy液气分离器Slug pit配浆罐(配药罐)Trip nipple旋转头喇叭口Rotating head旋转头Chickson 活动弯头Trailer/container/cabin/quarter room住井房/生活区Trash pump排污泵Flare pit放喷池/点火池/防火墙pup joint:短节重晶石:bariteWear bushing:防磨套膨润土:gelCasing tally:套管数据Float shoe:浮鞋Float collar:浮匝Protector:护丝WDC:wait on cement:候凝Measure out of hole:校对井深surface casing:表层套管intermediate casing:技术套管production casing:生产套管方瓦:hub卡瓦:slip碳酸钙:calcium carbonate环形防喷器:annular 半封:pipe ram全封:blind ram Drift :通径(vt)Gauge ring:通径规Resistivity:电阻套压:casing pressure油(管)压:tubing pressure XJH:须家河地层KOP:kick-off point:造斜点。

石油钻井工程英语词汇(5篇)

石油钻井工程英语词汇(5篇)

石油钻井工程英语词汇(5篇)第一篇:石油钻井工程英语词汇石油钻井工程英语词汇2008-10-15第一章:石油钻井工程英语基础词汇第1 节石油钻井工程基础词汇钻井:drill 定向斜井:directional drilling 欠平衡钻井:under-balance drilling 海上钻井:off-shore drilling 陆地钻井:on-shore drilling 钻头:drill bit 刮刀钻头:drag bit 牙轮钻头:rock bit(镶齿钻头insert bit, 钢齿钻头steel toothed bit)金刚石钻头:diamond bit 取心钻头:coring bit 钻头浮阀:float valve 钻头水眼:bit nozzle(or jet)钻头水眼刺:bit nozzle washed out 钻头规:bit caliper(bit gauge)钻头泥包:bit is balling 钻头钝了,我建议现在起钻:bit is dull.I suggest to POOH now 地址:北京市朝阳区东三环中路7号财富中心A座601邮编:100020 Address: Unit 601, Fortune Plaza Office Tower A, No.7 Dongsanhuan Zhong Rd, Chaoyang District, Beijing 100020, P.R.China钻铤:DC(drill collar)光钻铤slick drill collar,螺旋钻铤spiral drill collar 钻杆:DP(drill pipe)方钻杆:kelly 公扣:pin end 母扣:box end 内平式连接:IF(internal flash)正规式连接:REG(regular)贯眼式连接:FH(full hole)加重钻杆heavy weight drill pipe 短钻杆pop joint 井下马达:downhole motor 涡轮钻具:turbine 震击器:drilling jar 减震器:absorber 下部钻具组合:BHA(bottom hole assembly)钻具扶正器:stabilizer(string stabilizer, near-bit stabilizer)钻机:drill rig 钻井泥浆:drilling mud 钻井液:drilling fluid 钻井设备:drilling equipment油:oil 原油:crude oil 天然气:nature gas 煤层气:coal-bed gas 石油:petroleum 中国石油(简称):CNPC (China National Petroleum Corporation)长城钻井(简称):GWDC(Great Wall Drilling Company)采油:oil production 产油层(目的层):reservoir(or pay zone)钻进:drilling 调整钻井参数以得到理想的机械钻速:play the drilling parameters to get fast ROP 起钻:POOH(pull out of hole)下钻:RIH(run in hole)下套管:run casing(or RIH with casing)短起下钻:wiper trip 循环泥浆:circulate 泥浆:reverse circulate 中途循环泥浆:break circulation 分段下钻:RIH in stages 通井:control trip 划眼:reaming 倒划眼:back reaming 地址:北京市朝阳区东三环中路7号财富中心A座601邮编:100020 Address: Unit 601, Fortune Plaza Office Tower A, No.7 Dongsanhuan Zhong Rd, Chaoyang District, Beijing 100020, P.R.China 接单根:make connection 滑、割大绳:slip and cut drilling line by ton-mile 保养设备:maintain the equipment 修理设备: repair(or fix)the equipment 保养顶驱:service TDS 保养冲管:lubricate wash pipe 待工日费:standby rate 今天零日费:there is no day rate today(zero day rate today)我可以为您做,但必须收费,请理解I can do for you and I have to charge(back charge)you.Please give me full understanding.不在我的职责范围之内,我要汇报领导,一有消息会马上告诉你It is out of my power and I have to report to my boss.I will let you know as soon as I get news.大鼠洞:rat hole 小鼠洞:mouse hole 钻具错扣:the connections are crossed 钻具粘扣:thread is galled 丝扣坏了:the thread is damaged 起钻错扣:alternate the connections 新钻具或接头磨扣:break in the new tool joint 新钻头磨合:break in the new bit PDC 钻头井底造型:shape the PDC bit跳钻:rough drilling(vibrated drilling, bit is bouncing)蹩钻:rough drilling(drilling torque is abnormally high)缩径:tight hole 起钻遇卡:get overpull 下钻遇阻:set weight 部分漏失:partially lost circulation 全部漏失:totally lost circulation 盲钻:blind drilling 堵水眼:bit jets are blocked 掉水眼:bit jets are lost 憋压:the pressure is built up 卸压:release pressure 试压:pressure test 功能测试:function test 双方独自检查:double check 地质:geology 地质专业人员:geologist 物理:physics 地球物理勘探: geo-physical exploration.测井:logging 地址:北京市朝阳区东三环中路7号财富中心A座601邮编:100020 Address: Unit 601, Fortune Plaza Office Tower A, No.7 Dongsanhuan Zhong Rd, Chaoyang District, Beijing 100020, P.R.China 电测井作业:wireline logging operation 泥浆测井:mud logging 井(副词“好”含意):well 拓展记忆:井眼:bore hole 油气井:oil&gas well 试井:well test 井下:down-hole 井下作业:down-hole operation 第2 节石油钻井方法基础词汇钻井原理:the principles of drilling 顿钻钻井:percussion drilling,cable-tool drilling 旋转钻井:rotary drilling 大位移井:big distance(or extended)well 侧钻井:sidetracking drilling 水平井:horizontal well 探井:wildcat,wildcat drilling 深井:deep well 浅井:shallow well 老井:maturing well 丛式钻井:cluster well drilling 煤层气井:coal-bed gas well 生产井:production well 报废井:abandoned well 停产井:none-production well 井下情况:downhole condition 第3 节石油钻井技术基础词汇技术规范,技术指标,技术性能:specification 拉伸:tension 拉伸强度:tensile strength 弯曲强度:bending srength 最小屈服强度: minimum torsional strength 应力:stress 压力:pressure 应力点:stress point 压力降:pressure drop 压力梯度:pressure gradient 回压:back pressure 大气压:atmosphere 压差:pressure difference 静液柱压力:static fluid cloumn pressure 地层压力:formation pressure 坍塌压力:collapse pressure 地址:北京市朝阳区东三环中路7号财富中心A座601邮编:100020 Address: Unit 601, Fortune Plaza Office Tower A, No.7 Dongsanhuan Zhong Rd, Chaoyang District, Beijing 100020, P.R.China 破裂压力:fractured pressure 液体:liquid 固体:solid 气体:gas,air 正的:positive 负的:negative 水平的:horizontal 垂直的:vertical 第4 节石油钻井参数基础词汇钻压:WOB(weight on bit)转盘转速:RPM(rotation per minute)泵压:SPP(slurry pump pressure)泵冲:SPM(stroke per minute)排量:FR(flow rate)大钩负荷:hook load 扭矩:torque 反扭矩:reactive torque 钻速:ROP(rate of penetration)顶驱:TDS(top drive system)钻井周期:drilling period 钻井成本:drilling costs 井眼尺寸:hole size 垂深:TVD(total vertical depth)井深:MDD(measured depth)水平位移:horizontal displacement 井斜角:angle(or hole inclination)方位角:azimuth 井眼环空:annulus 第5 节石油钻井作业现场工作人员名称甲方:oil company(operator)钻井承包商:drilling contractor 第三方(分包商)the third party(sub-contractor)钻井经理:drilling manager 监督:supervisor 钻井监督:DSV(drilling supervisor)or Companyman 地质监督:geologist 泥浆工程师:mud engineer 固井工程师:cementing engineer 泥浆录井工:mud logger 钻井队:drilling crew,drilling team 钻井1 班:drilling shift one 总经理:general manager 总工程师:chief engineer 地址:北京市朝阳区东三环中路7号财富中心A座601 邮编:100020 Address: Unit 601, Fortune Plaza Office Tower A, No.7 Dongsanhuan Zhong Rd, Chaoyang District, Beijing 100020, P.R.China 项目经理:project manager(country manager)作业经理:operation manager 财务经理:financial manger 会计:accountant平台经理:rig manager 带班队长:tool pusher HSE 监督:HSE officer 司钻:driller 副司钻:assistant driller 井架工:derrick man 钻工:roughneck(or floorman)场地工:roustabout 泥浆工:mudman 发动机工:motorman 机械师:mechanic 电工:electrician 电焊工:welder 司机:driver 吊车司机:crane operator 铲车司机:forklift operator 营房经理:camp boss 医生:doctor 材料员:material man(storekeeper)炊事员:cook 翻译:interpreter 洗衣工:laundry man 厨房服务生:waiter 保安:watchman(or security)机械工程师:mechanic engineer 第6 节石油作业现场常用工具扳手:wrench 螺丝起子:screwdriver 多角螺丝起子:Phlilips screwdriver(cross-headed screwdriver)撬杠:bar 加长撬杠:cheater bar 活动板手:monkey wrench,adjustable wrench 钳子:pliers 钩子:hook 台钳:bench vice 钢挫:file 榔头:hammer 锤击扳手:hammer wrench 搬手:spanner 地址:北京市朝阳区东三环中路7号财富中心A座601邮编:100020 Address: Unit 601, Fortune Plaza Office Tower A, No.7 Dongsanhuan Zhong Rd, Chaoyang District, Beijing 100020, P.R.China 内六角扳手:Allen key 钢锯:hacksaw 砂纸:sandpaper 管钳:pipe tongs(pipe wrench)链钳:chain tong 千斤顶:jack 黄油枪:grease gun 吊车:crane 牵引绳:tag line 电焊条:welding rod 拖拉机:tractor 推土机:bulldozer 硬尺:ruler 游标卡尺:Vernier slide 油漆:paint 铅油:dope 油漆刷:paint brush 铅油刷:dope brush 绝缘胶布:electrical tape 电线:wire 插头:plug 电插座:outlet(receptacle or switchboard)开关:switch 螺栓:bolt 螺帽:nut 垫片:washer 钉子:nail 手电钻:hand drill 钻头:bit 工作台:workbench 工具箱:toolbox 胶水:glue 胶棒:glue bar 护丝:thread protector 手轮:hand wheel 脚轰油门:throttle 联接法兰:coupling flange(or adaptor flange)安全带:safety belt 安全帽:helmet 工作靴:safety boot 工衣:coverall 棉袄:coat 防护眼镜:safety goggle 地址:北京市朝阳区东三环中路7号财富中心A座601邮编:100020 Address: Unit 601, Fortune Plaza Office Tower A, No.7 Dongsanhuan Zhong Rd, Chaoyang District, Beijing 100020, P.R.China 手套:gloves 口罩:mouth mask 围裙:apron 洗眼台:eye washing station 灭火机:fire extinguisher 消防栓:fire-hydrant 水龙头:water tap 消防斧:fire fighting axe 铲子:shovel 手砂轮:emery wheel 左转: turn left 右转: turn right 手势:gesture 信号:signal 垃圾:waste garbage 拖把:mop 接头:sub 配合接头:X-over,cross-over 提升短节:lifting sub 卡瓦:slips 放卡瓦:set slips 母锥:box tap 公锥:taper tap 打捞矛:fishing spear 安全接头:safety sub 柔性短节:flexible joint 井口盖子:wellhead cover 防喷盒:mud box BOP 吊装:BOP trolley(BOP hoist)吊卡:elevator 吊环:elevator links 安全卡瓦:safety clamp(dog collar)钻杆架:pipe rack 水龙头提环:swivel bail 材料房:warehouse 绳卡:bullnose clamp(guy anchor)绳套:sling 吊带:soft sling(belt)卸扣:shackle 吊装工具:lifting gear 维护保养:maintenance 内钳:make-up tong 外钳:break-out tong 地址:北京市朝阳区东三环中路7号财富中心A座601邮编:100020 Address: Unit 601, Fortune Plaza Office Tower A, No.7 Dongsanhuan Zhong Rd, Chaoyang District, Beijing 100020, P.R.China 液压大钳:power tong 液压猫头:E-zy tong 兜绳:mule line 四通阀:four-way valve 三通:Tee 软管:hose 球阀:ball valve 闸板阀:gate valve 单流阀:back valve 灌注泵:supercharge pump 第二章:石油工程常用设备及专业术语第1 节钻井设备部分井架:Derrick(or mast)起(放)井架:erect(lay down)Derrick 底座大梁:sill 钢木基础:mat 铅锤:plumb 水平仪:level 架,台:rack 立根盒:setback area 坡道:V door(or ramp)猫道:catwalk 二层台:monkey-board 圆井盖:cellar cover 天车:crown block 防碰天车:crown-o-matic 天车梁:crown block beam 天车台:water table 游动滑车:traveling block 钻井大绳:drilling line 引绳:guide line 穿大绳:string-in drilling line 金属线,电线:wire,cable 钢丝绳股:strand 截断:cutoff 滑车,滑轮,皮带轮:pulley(hoist)手拉葫芦:hand pulley 吊耳:lifting eye 顶驱:top drive 大钩:hook 大钩弹簧:hook spring 大钩销子:hook pin 大钩锁紧装置:hook locking device 地址:北京市朝阳区东三环中路7号财富中心A座601邮编:100020 Address: Unit 601, Fortune Plaza Office Tower A, No.7 Dongsanhuan Zhong Rd, Chaoyang District, Beijing 100020, P.R.China 大钩悬挂高度:hook height 水龙头:swivel 鹅颈管:gooseneck 冲管:wash pipe 水龙头盘根:swivel packing 钻井水龙带: rotary hose(kelly hose)立管:stand pipe 立管管汇:stand pipe manifold 高压管线:high pressure line 由壬:union 低压管线:low pressure line 传感器:sensor 放压管线:relief line 转盘:Rotary Table 转盘方瓦:master bushing 方补心取出装置:bushing handling tool 方补心:kelly drive bushing 方孔: square opening 小鼠洞:mouse hole 大鼠洞:rat hole 绞车:Drawworks 挂合(摘开)绞车:engage(disengage)drawworks 液压绞车:hydraulic winch 气动绞车:air tugger(air hoist)滚筒: drum(reel)滚筒高速气离合器: high speed clutch 滚筒低速气离合器: low speed clutch 锚头:cathead 液压猫头:E-zy tong 上扣猫头:make up cathead 卸扣猫头:make out cathead 牙嵌离合器:jaw clutch 涡磁刹车:eddy current brake(electromagnetic brake)猫头轴:cathead shaft 猫头绳:cathead line 死绳:dead line 死绳固定器:dead line anchor 间隙:gap 死绳固定器膜片:dead line diaphragm 上扣:make up 上扭矩:torque sth 卸扣,卸开:break out 上紧,固定:tighten(fasten)地址:北京市朝阳区东三环中路7号财富中心A座601邮编:100020 Address: Unit 601, Fortune Plaza Office Tower A, No.7 Dongsanhuan Zhong Rd, Chaoyang District, Beijing 100020, P.R.China 松开,松扣:loosen 加载:load 卸载:unload 盘式刹车:disc brake 刹车总成:brake assembly 刹车轴:brakeshaft 刹车带:brake band 刹车片:brake block 液压油箱:hydraulic power unit 液动试压泵:hydraulic test pump 液压大钳:hydraulic(power)tong 倒档齿轮:reverse gear 动力扳手:power wrench 吊钳钳头:hinged jaw 钳牙:die 大钳锁销:latch 大钳悬臂:suspension bar平衡重:counterbalance weight 吊钳钳臂:tong arm 第2 节钻井泵类及相关设备泥浆泵:mud pump 活塞:piston 活塞杆:piston rod 活塞皮碗:piston cup 缸套:liner 凡尔体:valve body 凡尔座:valve seat 凡尔箱:pump module 阀弹簧:valve spring 阀杆:valve lever 阀面:valve face 阀帽:valve bonnet 空气包:pulsation damper 充氮气:refill with nitrogen 泥浆泵安全阀:pop-off valve 卸压管线:release line 排出阀:discharge valve 吸入阀:suction valve 上水滤子:screen 油尺:oil-level dipstick 灌注泵:supercharge pump 冷却水泵:cooling pump 潜水泵:submersible pump 地址:北京市朝阳区东三环中路7号财富中心A座601邮编:100020 Address: Unit 601, Fortune Plaza Office Tower A, No.7 Dongsanhuan Zhong Rd, Chaoyang District, Beijing 100020, P.R.China 盘根盒:stuffing box 叶轮:impeller 单向阀:check valve(single-pass valve)安全阀:safety valve 手动阀:manual valve 液动阀:hydraulic valve 拉杆:tie rod,tension bar 压力表:pressure gauge 冲数:strokes 排量:flow rate 80 冲(次)/分:eighty strokes per minute 泥浆罐:mud tank 倒泥浆:transfer mud 循环罐:active tank 储备罐:reserve tank 起下钻罐:trip tank 溢流检查:flow check 沉砂罐:satteling tank 锥形罐:sand trap 震动筛:sahle shaker 筛布:screen 目数:mash 除砂器: desander 除泥器: desilter 离心机: centrifuge 泥浆分配槽:spider box 缓冲罐buffer tank 第3 节与泵操作有关的实用短语没有压力:No pressure 压力过高:The pressure is too high 返回太少:Mud return is too few 水太少:Water is not adequate.抢修:Rush to repair 请看记录:Please check the record 没作记录:No record available 加化学药品:add chemicals 测定比重:measure mud weight(specific gravity)测定失水:measure water loss 泥饼:mud cake 测定切力:measure gel strength 停泵:stop pump 请打手势:Please make a gesture 转动一周:turn round a circle 地址:北京市朝阳区东三环中路7号财富中心A座601邮编:100020 Address: Unit 601, Fortune Plaza Office Tower A, No.7 Dongsanhuan Zhong Rd, Chaoyang District, Beijing 100020, P.R.China 垫高一些:put something under it to raise 抓紧:firmly grasp 抬高:lift it up 拿稳:hold firm 打一下: hit once 往外拉:pull outward 站稳:stand firm 小端:small end 大端:large end 光滑:smooth 粗糙:coarse,rough平面:flat 弯曲:bending 放松:loosen 绷直:stretch tight,draw tight 冷却:cooling 润滑:lubricate 过载:overload 功率不足:power is not enough.第4 节钻台与底座钻台:drilling floor 钻井班组记录:drilling tour record 司钻监视器:driller's monitor 司钻控制台:driller's console 指重表:weight indicator 底座:substructure 井队活动房:trailer 钻台上值班房:doghouse 梯子:ladder 第5 节井控操作与防喷器溢流: kick 溢流征兆: kick sign 气侵:gas cut 井喷:blow-out 1 次井控the primary well control 2 次井控the secondary well control 3 次井控the tertiary well control平衡balance 超平衡over-balance 欠平衡under balance 漏失试验leak-off test 破裂压力fracture pressure 额定压力 rated pressure 地址:北京市朝阳区东三环中路7号财富中心A座601邮编:100020 Address: Unit 601, Fortune Plaza Office Tower A, No.7 Dongsanhuan Zhong Rd, Chaoyang District, Beijing 100020, P.R.China 工作压力 working pressure 防喷器组BOP stack 安装(甩下)防喷器组:nipple up(nipple down)BOP stack 分流器diverter 万能防喷器:annular preventer,bag preventer 单闸板防喷器:single ram preventer 双闸板防喷器:double ram preventer (防喷器)闸板:pipe ram 变芯闸板防喷器variable bore ram 全封式防喷器:blind ram 剪切防喷器:shear ram 内防喷器 Inside BOP 投入式单流阀DIBPV(Drop in blowout preventer valve)分流关线diverter line 节流管汇choke manifold 节流阀choke valve 旁通阀standby valve 调压阀: Pressure regulator 手动节流阀manual choke 远程节流阀remote choke 井口四通drilling spool 变径法兰:adapter flange 液压控制阀 HCR(hydraulic controller)远程控制系统:koomey unit 蓄能器:accmulator 压井管线:kill line 入口:inlet 出口:outlet 简易除气器:poor-boy degasser 真空除气器:vaccum degasser 泥浆池液面纪录仪Pit volume recorder(totallizer)泥浆流动传感仪mud flow sensor 泥浆增量 Pit gains 硫化氢侵入H2S influx 加重材料Weighted material 氮气Nitrogen 乙炔:acetylene 氧气:oxygen 预冲氮气压力Pre-charge nitrogen pressure 地脚螺栓连接Studded connection 法兰连接 Flange connection 箍盘连接Hub connection 演习:drill 地址:北京市朝阳区东三环中路7号财富中心A座601邮编:100020 Address: Unit 601, Fortune Plaza Office Tower A, No.7 Dongsanhuan Zhong Rd, Chaoyang District, Beijing 100020, P.R.China 急救演习:first aid drill 消防演习:fire drill 防喷演习:kick drill 泄压: bleed off pressure 带刻度压力表: calibrated pressure gauge 带刻度容(体)积表: calibrated volume gauge 套管鞋: casing shoe 上部井眼段top hole section 快速钻进地层fast drilling formation 压实地层:consolidated formation 风化地层:weathered formation 钻屑携带能力cuttings carrying capacity 浅层气藏shallow gas 地层破裂formation to break down 压力梯度pressure gradient 地层压力formation pressure 井口压力wellhead pressure 漏失压力leak-off pressure 破裂压力fractured pressure 井底压力BHP(bottom hole pressure)正常压力normal pressure 异常压力abnormal pressure 静液压力hydrostatic pressure 动态压力dynamic pressure 环空压力annular pressure 关井钻杆压力SIDPP(shut in drill pipe pressure)关井套管压力SICP(shut in casingpressure)最大关井套管压力maximum allowable surface pressure, MAASP 最初循环压力 ICP(Initial circulating pressure)循环结束压力FCP(Final circulating pressure)U 形管原理U-tube principle 压井操作killing operation 补救措施remedial actions 关井后循环circulation under well closed in condition cl 离子含量chloride content Dc 指数 Dc exponent 软关井soft shut in 硬关井hard shut in 第1 次循环first circulation 第2 次循环second circulation 压井泥浆比重kill mud weight 抽吸swab 激动surge 地址:北京市朝阳区东三环中路7号财富中心A座601邮编:100020 Address: Unit 601, Fortune Plaza Office Tower A, No.7 Dongsanhuan Zhong Rd, Chaoyang District, Beijing 100020, P.R.China 含气地层gas bearing formation 含气页岩gas bearing shale 安全增量safety margin 记录卡片trip sheet 低循环泵速SCR(slow circulation rate)当量泥浆密度EQD(equivalent mud density)当量循环密度ECD(equivalent circulating density)司钻压井法driller’s method等待压井法wait & weight method 体(容)积法volumetric method 下推压井法bull-heading method 不压井下钻:snub in 第三章:钻井工程作业部分第1 节钻井事故井喷:blow out 井涌:kick 井漏:lost circulation 坍塌,井壁坍塌:cave in(collapse)出砂:sand production 砂桥:sand bridge 台阶:ledge 键槽:keyseat 椭圆井眼:oval shaped hole 卡钻:sticking 填井:pack-hole 封井:packed drilling 井下落物:fish 大幅度活动钻具试图解卡:work the string and try to free it 活动钻具以避免卡钻:move(reciprocate)the string to avoid being stuck.打捞:fishing 鱼头:top of fish 打捞工作:fishing job 侧钻:side-tracking 侧钻井眼:sidetracking hole 水泥窜槽:cement channeling 固井失败:cement failure 防砂:sand control 缓慢开泵并仔细观察返浆情况:slowly start pumping and closely watch the return on the shale shaker 第2 节钻头牙轮钻头:rock bit 刮刀钻头:drag bit 金钢石钻头:diamond bit 地址:北京市朝阳区东三环中路7号财富中心A座601 邮编:100020 Address: Unit 601, Fortune Plaza Office Tower A, No.7 Dongsanhuan Zhong Rd, Chaoyang District, Beijing 100020, P.R.China 镶齿钻头: insert bit 铣齿钻头:milled tooth bit 喷射钻头:jet bit 牙轮:cone 钻头装卸器:bit breaker 钻头直径:bit diameter 钻头寿命:bit life 钻头磨损:bit wear 钻头型号:bit type 水眼尺寸:nozzle size 水眼效率:nozzle efficiency 钻头接头:bit sub 第3 节钻具方钻杆:kelly 方钻杆旋扣器:kelly spinner 方钻杆旋塞:kelly cock 钻具:drilling string 钻杆:drill pipe 油管:tube 钻具组合:drilling assembly 扶正器:stabilizer 扩眼器:reamer(hole opener)钻铤:drill collar 无磁钻铤:NMDC(non-magnetic drill collar)加重钻杆:HWDP(heavy weight drill pipe)近钻头扶正器:near-bit stabilizer 震击器:jar 减震器:shock absorber 螺旋钻铤:spiral drill collar 键槽破坏器:key seat reamer 安全接头:safety joint 钻杆刮泥器:drill pipe wiper 泥浆动力钻具:mud motor 钻柱:drill string 涡轮:turbine 涡轮钻具:turbo-drill stem 立根:stand 加厚:upset 内加厚:IU(internal upset)外加厚:EU(external upset)内外加厚:internal-external upset 丝扣:thread 打捞颈:fishing neck 地址:北京市朝阳区东三环中路7号财富中心A座601邮编:100020 Address: Unit 601, Fortune Plaza Office Tower A, No.7 Dongsanhuan Zhong Rd, Chaoyang District, Beijing 100020, P.R.China 母扣:box 公扣:pin 左旋螺纹:left-hand thread 右旋螺纹:right-hand thread 正规接头:regular joint 贯眼接头:full hole joint 内平接头:internal flush joint 护丝:thread protector 快速护丝:easy protector 打捞工具:fishing tool 打捞作业:fishing operation 打捞篮:junk basket 卡瓦打捞筒:overshot 打捞杯:junk sub 牙轮打捞器:cone fisher 套管打捞矛:casing spear 打捞矛:fishing spear 打捞公锥:male tap(fishing nipple)打捞母锥:female tap(fishing socket)倒扣工具:reversing tool(backing-up tool)铣鞋:milling shoe 铣具:milling tool平底铣鞋:flat bottom mill 磁力打捞工具:magnetic fishing tool 打捞钩:fish hook 气动工具:pneumatic tool 减摩短节:friction reduction sub 下套管漂浮接箍:casing floating coupling 轴向加压器:hydraulic axial thruster 第4 节钻井工程地面作业实用词汇与短语方入:kelly-in 方余:kelly-up 开钻:spud in 作业指令:instruction 钻井设计:drilling program 井身结构:well schematic 岩性:lithology 迟到时间:lag time(bottom up)换钻头:change bit 甩钻具:laydown drill pipe 发生故障:break down 安装(拆卸):rig up(rig down)接头:sub adapter 地址:北京市朝阳区东三环中路7号财富中心A座601邮编:100020 Address: Unit 601, Fortune Plaza Office Tower A, No.7 Dongsanhuan Zhong Rd, Chaoyang District, Beijing 100020, P.R.China 机械手:mechanical arm 铁钻工:iron roughneck 有故障:It fucked up(something is wrong with it)已修好:it has been fixed 马上去:Go there at once 请下去:Please go down 请上来:Please come up 躲开,危险:keep away,danger.请翻译来:Ask interpretor come here,冲洗:wash down 井口:well-head 一根钻杆(单根):single 三根钻杆组合(立根):thribble 吊蓝:cage(basket)换班: shift change 第5 节钻井工程井口作业实用词汇与短语喇叭口:bell nipple 出水管:mud return line(flow line)试压杯:cup tester 小心滑倒:wet floor, be careful 不要往井眼内掉东西:never fall down anything inside hole 我来做:Let me do it 带把板手来:Bring a spanner,please 带点密封剂:Bring a little sealant(Teflon),please 很快就好了:lt will be finshed right away 抬一下:Let's lift it 把绳子给我:Give me the rope,please 不漏:no leakage 电焊: welding 气焊:gas welding 气割:gas cut 栏杆:handrail,gangway rail,railing 蒸汽:vapour 压缩空气:pressurized(compressed)air 注意安全:pay attention tosafety 别动:Don't move,Don't touch.对准:point out exactly.校正:align 裸眼:open hole 第四章:钻井液及相关设备第1节钻井液名称泥浆:mud 钻井液:drilling fluid 地址:北京市朝阳区东三环中路7号财富中心A座601邮编:100020 Address: Unit 601, Fortune Plaza Office Tower A, No.7 Dongsanhuan Zhong Rd, Chaoyang District, Beijing 100020, P.R.China 完井液:completion fluid 修井液:work-over fluid 压井液:killing fluid 射孔液:perforating fluid 隔离液:spacer fluid 泥浆处理:mud treatment 泥浆处理设备:mud treating equipment 饱和盐水泥浆:saturated salt-water mud 油基泥浆:oil-base mud 高粘度泥浆:heavy viscous mud 重泥浆:weighted mud 重泥浆压钻杆:slug drill pipe 起钻倒返泥浆:we have wet pipeduring POOH 重晶石:barite 纯碱:soda ash 高岭土粉:koaline powder 云母片: mica sheet 增粘剂: viscosifier 稀释剂:diluent(thinner)稳定剂:stabilizer(stabilizing agent)烧碱:caustic soda 稀释dilution, thinning 水泥凝固cement setting 第2 节钻井液设备离心泵:centrifugal pump 振动筛跑泥浆:mud overflow shale shaker 筛出:shake out 混合泵:mixing pump 混合漏斗:mixing hopper 搅拌器:mud agitator 泥浆抢:mud gun 岩屑:cuttings 沉淀:settle 沉积物:deposit 吸入:suction 吸入罐:suction pit 泥浆天平:mud balance 游码:slide weight 支点:fulcrum 刀口:edge 调整,校正:adjust 粘度计:viscometer 第3 节钻井液处理剂地址:北京市朝阳区东三环中路7号财富中心A座601邮编:100020 Address: Unit 601, Fortune Plaza Office Tower A, No.7 Dongsanhuan Zhong Rd, Chaoyang District, Beijing 100020, P.R.China 包,袋:sack 粘土:clay 膨润土,般土:bentonite 钠:sodium 钙:calcium 氯:chloride 氯化钙:calcium chloride 石棉:asbestos 分散:dispersal 表面活性剂:surface-active material 铁络盐:lignite 单宁:tannin 羧甲基纤维素:carboxymethyl celluose CMC 木纤维:xylogen 石灰:lime 二氧化钙:calcium oxide 粉末:powder 薄片:flake 溶解:dissolve 延迟,妨碍:retard 处理剂,添加剂:additives 缓凝剂:retarder 支撑剂:proppant 乳化剂:emulsifier 润湿剂:wetting agent 稳定剂:stabilizing agent 除钙剂:calcium remover 降失水剂:filtration-reducing agent PH 值控制剂:PH control additive 润滑剂:lubricant 消泡剂:defoamer agent 破乳剂:emulsion breaker 洗涤剂:detergent 防膨胀剂:anti-swelling agent 粘土稳定剂:clay stable agent 稀释剂:thinner 封堵剂:plugging agent 抑制剂:inhibition agent 暂堵剂:temporary plugging agent 解堵剂:plugging removal 堵漏剂:LCM(lost circulation material)水敏地层:water-sensitive formation 分散:dispersal 地址:北京市朝阳区东三环中路7号财富中心A座601邮编:100020 Address: Unit 601, Fortune Plaza Office Tower A, No.7 Dongsanhuan Zhong Rd, Chaoyang District, Beijing 100020, P.R.China 水泥浆:cement slurry 流变性:rheological characteristics 稳定性:stability 稠化时间:thickening-time 低密度水泥浆:low-density slurry 油气层保护:reservoir protection 高渗透性:high-permeability 砾石:gravity 悬浮:suspension 固化:solidification.防膨胀:anti-swelling 高凝高粘度:high condensation and viscosity 无毒的:non-poisonous 无荧光:non-fluorescence 钻井液性能参数Specificaitons of Drilling Fluid 含水:water content 密度:density 厚度:thickness 粘度:viscosity 塑性粘度:plastic viscosity 含砂量:sand content 屈服:yield 屈服点:yield point 屈服强度:yield strength 剪切速率:shear rate 剪切强度:shear strength 剪切应力:shear stress 稀释:dilute 适用温度:safe temperature 初始切力:initial gel strength 终切力:ten-min gel strength 触变性:thixotropy 剪切稀释:shear thining 液体浓度:concentration 泥浆柱:mud column 层流:laminar flow 涡流:turbulent flow 气泡:bubble 第五章:钻井相关作业第1节取芯部分岩心:core 取心钻头:core bit 取心筒:core barrel 地址:北京市朝阳区东三环中路7号财富中心A座601 邮编:100020 Address: Unit 601, Fortune Plaza Office Tower A, No.7 Dongsanhuan Zhong Rd, Chaoyang District, Beijing 100020, P.R.China 内岩心筒:inner barrel 外岩心筒:outer barrel 岩心爪:core catcher 取心工具:corehandling tools 取心收获率:core recovery rate 取样器:sample blob 取样盒:sample box 样品筒:sample chamber 取样工:sample catcher 取样间隔:sample interval 井壁取心:side-wall coring 井壁取心枪:side-wall coring gun 取芯失败:coring failure 第2 节固井部分固井:cementing 完井:well completion 水泥:cement 井口:wellhead 井口压力:well head pressure 井口回压:back pressure on the well head 套压:casing pressure 导管:conductor 表层套管:surface casing 技术套管:protective casing(intermediatecasing)油层套管:production casing 尾管:liner 尾管悬挂器:liner hanger 通径轨:rabbit 封隔器:packer 联顶节:landing joint 套管柱casing string 套管下部结构(含套管鞋、浮箍):casing track(including casing shoe, float collar)套管扶正器:centralizer 止退环:stop collar 口袋:pocket(rat hole)环空注水泥作业:top cement job 碰压:bump plug 隔离液:spacer 分级箍:stage collar 水泥粘结强度strength of cement bond 套管钳:casing tongs 套管接箍:casing coupling 地址:北京市朝阳区东三环中路7号财富中心A座601邮编:100020 Address: Unit 601, Fortune Plaza Office Tower A, No.7 Dongsanhuan Zhong Rd, Chaoyang District, Beijing 100020, P.R.China 套管头:casing head 散装水泥:bulk-cement 水泥浆:cement slurry 插管注水泥:stab in cementing 插入密封接头:stab in adapter 分级注水泥:stage cementing 先行水泥浆:lead cement slurry 末端水泥浆:tail cement slurry 促凝剂:accelerator 替浆:displace with mud 水泥面:top of cement 固井管线:chicksan line(cementing line)灰罐:silo(bulk tank)候凝:WOC(wait-on-cement)挤水泥:squeeze cement 水泥塞:plug 第3 节固井水泥浆名称和参数超细水泥浆:ultrafine slurry 普通水泥浆:normal slurry 纤维水泥浆:fiber-reinforced cement slurry 膨胀水泥浆:expanding cement slurry 低密度水泥浆:low-density slurry 水泥体积收缩:cement volume contraction 水泥浆水化期间:cement slurry hydrating period 水泥胶结质量:cement sheath bonding quantity 失水率:the rate of water loss 析水:liberate water 稠化时间:thickening time 凝固强度:cementation strength 渗透性:permeability,膨胀率:expansion rate 压缩强度:compression strength 流动性:mobility 第4 节测井部分电测:wireline logging 测井解释:logging interpretation 随钻测井:LWD(logging while drilling)测井电缆:logging cable 测井工具:logging tool 自然电位测井:spontaneous potential log 感应电测井:induction electrical survey 双感应测井:dual induction-laerolog 中感应测井:medium induction log 地址:北京市朝阳区东三环中路7号财富中心A座601邮编:100020 Address: Unit 601, Fortune Plaza Office Tower A, No.7 Dongsanhuan Zhong Rd, Chaoyang District, Beijing 100020, P.R.China 数字记录:digital record 照相记录:photographic recording 放射性测井:radioactivity log 声波技术:acoustic wave technology 仪器耐温:the temperature resistance of the instrument 仪器耐压:pressure resistance of instrument 油气比:GOR(gas oil ratio)第六章:井下作业常用短语修井:work-over 修井工具:work-over tool 井下操作: down-hole operations.产层污染: pollution of pay zone 增产措施:stimulations 压裂和酸化:fracturing or acidizing 酸化处理:acid treatment 人工压裂:artificial fracturing 重复压裂过程:repetition presses for fracturing,压裂车:fracturing truck sets 压裂后反映:post-fracture response 固体和液体添加泵:solid and liquid additivepump 泵交联: pumping cross link 交联剂: cross-linking agent 排量: discharging 三维压裂: three-dimension fracturing 对压裂参数的监控、分析和解释:real time monitoring,analyzing and interpreting for fracturing operation parameters 压裂操作:fracturing operation 压裂规模:fracturing scale 化学吞吐:chemical disposal 乳化降粘:emulsification declining viscosity 增注:augmented injection.注水:water-injection 裸眼砾石填充完井:bore hole gravel packer completion.开窗铣锥:open-window mill prick,开窗斜向器:open-window inclined implement 碳酸盐岩:carbonate reservoir 第七章:海上钻井作业¨海上钻井:offshore drilling 陆地钻井:on-land drilling 海滩:sea beach 浅海:shallow sea 海底管线:sea-bottom pipe 地址:北京市朝阳区东三环中路7号财富中心A座601邮编:100020 Address: Unit 601, Fortune Plaza Office Tower A, No.7 Dongsanhuan Zhong Rd, Chaoyang District, Beijing 100020, P.R.China 海底电缆铺设:setting cable under sea-bottom 平台安装:platform installation 钻井平台:drilling platform 顺风:tail wind 逆风:against the wind 摄氏零下…度:below…degree centigrade 启锚:weigh anchor 抛锚:drop anchor 拖航:drag 对讲机:intercom,walkie-talkie 上吊茏:Please get on the liftbasket 救生衣:life jacket 晕船:sea sick 控制速度:Control the speed 货已送抵:The goods has arrived 货物验收:Please check and accept the goods 在不远处:Not far from here 不方便:lt's not convenient 有危险:lt's dangerous 防污染:prevent pollution 没情况:Nothing happened.第八章:定向井部分定向井:directional well 造斜点:KOP(kick off point)最大井斜角:maximum hole inclination 增斜段:building up section 稳斜段:holding section 降斜段:drop off section 井眼尺寸:hole size 长、中、段半径:long,medium and short radius 裸。

  1. 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
  2. 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
  3. 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。

行业英语之实用词汇现场实用词汇短语一、甲方乙方1. 承包商人员 ( Contractor’s Personnel )Equipment Supervisor 设备总监Materials Supervisor 材料总监Senior Toolpusher 高级队长Junior Toolpusher 值班队长Driller 司钻Sub Sea Engineer (SSE) 水下工程师Assistant Driller (AD) 副司钻Derrick Man 井架工Floor Man (roughneck) 钻工Crane Operator 吊车工Mechanic 机械师Electrician 电气师Repairman 修理工Welder 焊工Radio Operator 电报员Warehouse Man (stock Keeper) 材料员Medic 医生Safety Supervisor 安全监督Interpreter (translator) 翻译Chief Steward 管事Cook 厨师2、作业者及服务公司人员( Operator’s Personnel and Service Company Personnel)Drilling Superintendent 钻井监督Company Man (Operator’s Representative) 公司代表Geologist 地质师Mud Logging Engineer (Mud logger) 泥浆录井工程师Sample Catcher 捞砂工Mud Engineer 泥浆工程师ROV Engineer 潜水工程师Cementer 固井工Cement Engineer 固井工程师Testing Engineer 试油工程师Coring Engineer 取芯工程师Wireline Logging Engineer电测工程师二、主要设备1.钻井设备 (Drilling Equipment):Drawworks 钻井绞车Rotary Table 转盘Bushing 补心Top Drive System (TDS) 顶驱Swivel 水龙头Crown Block 天车Traveling Block 游车Hook 大钩Derrick 井架Pipe Spinning Wrench 钻杆气动扳手Ezy-Torq 液压猫头Elmagco Brake 涡磁刹车Pipe handling Equipment 钻杆移动设备Iron roughneck 铁钻工Pipe Racking System 钻杆排放系统Drill String 钻柱Drilling Sub 钻井短节Fishing Tool 打捞工具Power Tong 动力大钳Air Winch (air tugger) 气动绞车Crown-O-Matic (Crown Saver) 防碰天车2. 泥浆系统 (Mud System)Mud Pump 泥浆泵Shale shaker 振动筛Mud Cleaner 泥浆清洁器Desilter 除泥器Desander 除砂器Degasser 除气器Centrifuge 离心机Mud Agitator 泥浆搅拌器Mud Mixing System 泥浆混合系统Centrifugal Pump 离心泵Standpipe Manifold 立管管汇Rotary Hose 水龙带Bulk Air System and Tank 吹灰系统和灰罐3. 井控设备 (Well Control Equipment):Ram Type Preventor 闸板防喷器Annular Type Preventor 万能防喷器BOP Stack 防喷器组Gate Valve 闸阀Choke and Kill Manifold 阻流压井管汇Remotely Operated Panel 远程控制面板Choke Control Panel 阻流控制面板BOP Handling Equipment 防喷器搬运设备Diverter 转喷器五. 机房(Engine Room)Diesel Engine 柴油机Emergency Generator 应急发电机Water Maker (desalinization unit) 造淡机Air Compressor 空气压缩机Boiler 锅炉Air-conditioning System 空调系统Piping System 管汇系统Generator 发电机Transformer 变压器DC Motor 直流马达AC Motor 交流马达4. 安全设备 (Safety Equipment) Fire Control System 消防控制系统Fire Detection System 火情探测系统Fixed Fire Extinguishing System 固定消防系统Portable Extinguisher 移动灭火器Fire-Fight Equipment 消防设备Foam System 泡沫系统Escape Routes 逃生路线Breathing Apparatus 呼吸器Gas Detection System 气体探测系统Helicopter Facility 直升机设施Sick-Bay (Hospital) 医务室Pollution Control 防污控制5. 其他 ( Others)Cementing Unit 固井装置Well Testing Equipment 试油设备Mud Logging Unit 泥浆录井房Wire Logging Unit 电测装置ROV 潜水器Meter 米Foot 英尺Inch 英寸Day (night) Shift 白(夜)班Crew Change 倒班Position 岗位Penetration (桩腿插桩)入泥Evacuation 撤离Rig (Drilling rig) 钻机, 钻井船Quarters (living quarters, accommodation area) 生活区Drill Floor (Rig floor) 钻台Bridge (Pilot house, Steerwheel house) 驾驶室Control Room 控制室Helideck 直升机甲板Cementing Unit Room 固井泵房Air Compressor Room 空气压缩机房BOP Control Room BOP控制房Radio Room 报房Engine Room 机房Warehouse (Store) 材料库房Paint Room (paint locker) 油漆房库Mud pit 泥浆池Pipe Rack Area 钻杆排放区Pipe Slide 滑道Ramp 坡道Pump Room 泵房Shale Shaker House 振动筛房Coffee Room 咖啡室Mess (dining) Room 餐厅Recreation Room 娱乐房TV RoomChange Room 工衣房Kitchen 厨房三、钻具,井口工具,打捞工具Drill Pipe 钻杆Drill Collar 钻铤Heavy Weight Drill Pipe 加重钻杆Elevator 吊卡Tong 大钳Make-up Tong 上扣大钳Break-out Tong 卸扣大钳Mud Box 泥浆防喷盒Casing Stabbing Board 套管扶正器Slips 卡瓦Spider 卡盘Mouse Hole 小鼠洞(接单根用)Kelly Spinner 方钻杆旋转器Kelly Cock 方钻杆阀Chain Tong 链钳Casing 套管Tubing 油管Drill String 钻柱Jar (drilling jar) 震击器Right Hand Thread 正扣Left Hand Thread 反扣Stabilizer 扶正器Rabit 通管器Liner 尾管Conductor 导管Thread Protector 护丝Stand (钻杆) 立柱Single (钻杆) 单根Joint (钻具) 根Bend 弯头Sub 短节Pup Joint 短钻杆, 短节Connector 接头Bit 钻头Bit Breaker 钻头盒Box 母扣Pin 公扣Hole Opener 开眼钻头Reamer 扩眼钻头Overshot 打捞筒Junk Basket 打捞篮Junk Mill 平头磨鞋Spear 打捞矛Fishing Tap 打捞公锥Cross Over Sub (XO Sub) 转换接头Bottom Hole Assembly (BHA) 下部钻具组合四. 材料和工具Steel 钢Iron 铁Wood 木Chemicals 化学品Cement 水泥Barite 重晶石Potable Water 淡水Fuel 柴油Lubricant (Lube/Lube oil) 润滑油Grease 黄油Ballast Water 压载水Gasoline 汽油Mud 泥浆Additive 添加剂Caustic Soda 烧碱Weight Material 加重材料Oxygen 氧气Nitrogen 痰气Hydrogen Sulphide 二氧化硫Acetylene 乙炔Compressed Air 压缩空气Hydraulic Fluid 液压油Spanner 扳手Hammer 铁锤Screw Driver 螺丝刀Multimeter 万用表Welding Machine 焊机Bar 撬杠Shackle 卸扣Sling (钢丝) 绳套。

相关文档
最新文档