常用船舶词汇
船舶英语词汇
船舶专用词汇1.船舶的分类passenger ship 客船general cargo ship 杂货船bulk cargo carrier 散货船container ship 集装箱船roll on/roll off ship 滚装船tanker 油船liquid gas carrier 液化气船barge 驳船barge carrier 载驳船dredger 挖泥船floating crane 起重船floating dock 浮船坞ice breaker 破冰船drilling platform 钻井平台drilling ship 钻井船trawler 拖网渔船stern ramp trawler 尾滑道拖网渔船tug boat 拖船fire boat 消防船ocean survey ship 海洋调查船cruiser 巡洋舰destroyer 驱逐舰frigate 护卫舰aircraft carrier 航空母舰submarine 潜艇hydrofoil craft 水翼艇air cushion vehicle 气垫船—hovercraft 全浮式气垫船—sidewall air cushion vehicle 侧壁式气垫船small waterplane area twin hull ship 小水线面双体船semi-submerged catamaran 又称为半潜双体船2.船体结构longitudinal bending 总纵弯曲hogging 中拱弯曲sagging 中垂弯曲longitudinal strength 总纵强度transverse strength 横向强度local strength 局部强度hull 船体superstructure 上层建筑stem 船首midship 船中stern 船尾forecastle 艏楼bridge 桥楼poop 艉楼deck house 甲板室ship bottom 船底ship side 舷侧upper deck 上甲板lower deck 下甲板transverse bulkhead 横舱壁longitudinal bulkhead 纵舱壁fore peak bulkhead 艏尖舱舱壁after peak bulkhead 艉尖舱舱壁3.外板和甲板板shell plate 外板seam 边接缝butt 端接缝strake 列板bottom plate 船底板plate keel 平板龙骨bilge strake 舭列板side plate 舷侧外板sheer strake 舷顶列板upper deck 上甲板second deck 第二甲板third deck 第三甲板platform deck 平台甲板deck plate 甲板板deck stringer 甲板边板sponson deck 舷伸甲板4.船底结构center keelson 中内龙骨side keelson 旁内龙骨T-bar T型材web 腹板bracket 肘板face plate 面板flange 钢板折边法兰bilge bracket 舭肘板floor 肋板solid floor 主肋板watertight floor 水密肋板bracket floor 框架肋板lightened floor 轻型肋板stiffener 加强筋扶强材bulb plate 球扁钢angle bar 不等边角钢bottom center girder 中底桁bottom center girder 旁底桁duct keel 箱形中底桁pipe tunnel 管隧reverse frame 内底横骨bottom frame 船底肋骨longitudinal 纵骨bottom longitudinal 船底纵骨inner bottom longitudinal 内底纵骨inner bottom plate 内底板margin plate 内底边板man hole 人孔bilge well 污水井bottom side tank 底边舱foundation seating 基座shaft tunnel 轴隧tunnel recess 艉室emergency exit 应急通道bilge keel 舭龙骨5.舷侧结构Integrated barge 分节驳frame 肋骨main frame 主肋骨tweendeck frame 甲板间肋骨intermediate frame 中间肋骨web frame 强肋骨side longitudinal 舷侧纵骨cross tie 撑杆wing tank 舷边舱ballast water tank 压载水舱torsion box 抗扭箱bulwark 舷墙fender 护舷材6.甲板结构beam 横梁deck beam 普通横梁hatch end beam 舱口端横梁deck girder 甲板纵桁side stringer 舷侧纵桁hatch side girder 舱口纵桁beam knee 梁肘板sponson deck 舷伸甲板deck longitudinal 甲板纵骨web beam 强横梁cargo hatch 货舱口hatch coaming 舱口围板gusset plate 菱形板hatch side cantilever 悬臂梁pillar 支柱topside tank 顶边舱excess hatch 出入舱口expansion trunk 膨胀井7.舱壁结构bulkhead 舱壁cofferdam 隔离空舱partial bulkhead 局部舱壁plane bulkhead 平面舱壁bulkhead plate 舱壁板tweendeck bulkhead 甲板间舱壁vertical stiffener 垂直扶强材8.首尾端结构vertical bow 直立型艏raked bow 前倾型艏clipper bow 飞剪型艏ice breaker bow 破冰型艏elliptical stern 椭圆形艉cruiser stern 巡洋舰型艉transom stern 方形艉fore peak艏尖舱collision bulkhead 防撞舱壁raised floor 升高肋板panting beam 强胸横梁wash bulkhead 制荡舱壁chain locker 锚链舱breast hook 艏肘板stem 艏柱steel plate stem 钢板艏柱forged steel stem 锻钢艏柱combination cast and rolled stem 混合式艏柱tunnel 管隧thruster 侧推器after peak 艉尖舱shaft tube 艉轴管cant frame 斜肋骨cant beam 斜横梁stern frame 艉柱shoe piece 艉柱底骨rudder post 舵柱propeller post 螺旋桨柱propeller shaft strut 艉轴架A-bracket 人字架shell bossing 轴包套spectacle frame 眼镜形骨架9.上层建筑和机舱棚结构accommodation 起居甲板boat deck 艇甲板navigation deck 驾驶甲板compass deck 罗经甲板compass platform 罗经平台expansion joint 伸缩接头derrick post桅杆derrick platform 起货机平台tower post 塔式桅stern door 艉门bow door 艏门visor type 罩壳式side hinged type 边铰链式pressure structure 耐压结构non pressure structure 非耐压结构pressure conning tower 耐压指挥台pressure tank 耐压水舱pressure bulkhead 耐压舱壁oil ballast tank 燃油压载水舱ballast water tank 压载水舱conning tower sail 指挥台围壳渔业船舶种类2.1 渔船fishing vessel 用于商业性捕捉鱼类、鲸、海豹、海象或其他生物资源的船舶之统称。
船舶专业常用词汇
船舶专业常用词汇a faired set of lines 经过光顺处理的一套型线a stereo pair of photographs 一对立体投影相片abaft 朝向船体abandonment cost 船舶废置成本费用accommodation 居住（舱室）accommodation ladder 舷梯adjust valve 调节阀adjustable-pitch 可调螺距式admiralty 海军部advance coefficient 进速系数aerostatic 空气静力学的aft peak bulkhead 艉尖舱壁aft peak tank 艉尖舱aileron 副鳍air cushion vehicle 气垫船air diffuser 空气扩散器air intake 进气口aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼，翼剖面，机面，方向舵alignment chock 组装校准用垫楔aluminum alloy structure 铝合金结构American Bureau of Shipping 美国船级社amidships 舯amphibious 两栖的anchor arm 锚臂anchor chain 锚链anchor crown 锚冠anchor fluke 锚爪anchor mouth 锚唇anchor recess 锚穴anchor shackle 锚卸扣anchor stock 锚杆angle bar 角钢angle of attack 攻角angle plate 角钢angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷anti-pitching fins 减纵摇鳍antiroll fins 减摇鳍anti-rolling tank 减摇水舱appendage 附体artisan 技工assembly line 装配流水线at-sea replenishment 海上补给augment of resistance 阻力增额auxiliary systems 辅机系统auxiliary tank 调节水舱axial advance 轴向进速backing structure 垫衬结构back-up member 焊接垫板balance weight 平衡锤ball bearing 滚珠轴承ball valve 球阀ballast tank 压载水舱bar 型材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船baseline 基线basic design 基本设计batten 压条，板条beam 船宽，梁beam bracket 横梁肘板beam knee 横梁肘板bed-plate girder 基座纵桁bending-moment curves 弯矩曲线Benoulli’s law 伯努利定律berth term 停泊期bevel 折角bilge bracket 舭肘板bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩blade root 叶跟blade section 叶元剖面blast 喷丸block coefficient 方形系数blue peter 出航旗boarding deck 登艇甲板boat davit 吊艇架boat fall 吊艇索boat guy 稳艇索bobstay 首斜尾拉索 body plan 横剖面图bolt 螺栓，上螺栓固定Bonjean curve 邦戎曲线boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁bottom side tank 底边舱bottom transverse 底列板boundary layer 边界层bow line 前体纵剖线bow wave 艏波bowsprit 艏斜桅bow-thruster 艏侧推器box girder 箱桁bracket floor 框架肋板brake 制动装置brake band 制动带brake crank arm 制动曲柄brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸brake hydraulic pipe 刹车液压管breadth extreme 最大宽，计算宽度breadth moulded 型宽breakbulk 件杂货breasthook 艏肘板bridge 桥楼，驾驶台bridge console stand 驾驶室集中操作台BSRA 英国船舶研究协会buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulb plate 球头扁钢bulbous bow 球状船艏，球鼻首bulk carrier 散货船bulk oil carrier 散装油轮bulkhead 舱壁bulwark 舷墙bulwark plate 舷墙板bulwark stay 舷墙支撑buoy tender 航标船buoyant 浮力的buoyant box 浮箱Bureau Veritas 法国船级社butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例，按约定cable ship 布缆船cable winch 钢索绞车CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程camber 梁拱cant beam 斜横梁cant frame 斜肋骨cantilever beam 悬臂梁capacity plan 舱容图CAPP(computer –aided process planning) 计算机辅助施工计划制定capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容，载货容积cargo handling 货物装卸carriage 拖车，拖架cast steel stem post 铸钢艏柱catamaran 高速双体船catamaran 双体的cavitation 空泡cavitation number 空泡数cavitation tunnel 空泡水筒center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心，重心，质心，矩心chain cable stopper 制链器chart 海图charterer 租船人chief engineer 轮机长chine 舭，舷，脊chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论classification society 船级社cleat 系缆扣clipper bow 飞剪型船首clutch 离合器coastal cargo 沿海客货轮cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船commuter 交通船compartment 舱室compass 罗经concept design 概念设计connecting tank 连接水柜constant-pitch propeller 定螺距螺旋桨constraint condition 约束条件container 集装箱containerized 集装箱化contract design 合同设计contra-rotating propellers 对转桨controllable-pitch 可控螺距式corrosion 锈蚀，腐蚀couple 力矩，力偶crane 克令吊，起重机crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱criterion 判据，准则Critical Path Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积crow’s nest桅杆瞭望台cruiser stern 巡洋舰尾crussing range 航程cup and ball joint 球窝关节curvature 曲率curves of form 各船形曲线cushion of air 气垫damage stability 破损稳性damper 缓冲器damping 阻尼davit arm 吊臂deadweight 总载重量de-ballast 卸除压载deck line at side 甲板边线deck longitudinal 甲板纵骨deck stringer 甲板边板deck transverse 强横梁deckhouse 舱面室，甲板室deep v hull 深v型船体delivery 交船depth 船深derrick 起重机，吊杆design margin 设计余量design spiral 设计螺旋循环方式destroyer 驱逐舰detachable shackle 散合式连接卸扣detail design 详细设计diagonal stiffener 斜置加强筋diagram 图，原理图，设计图diesel engine 柴油机dimensionless ratio 无量纲比值displacement 排水量displacement type vessel 排水型船distributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠double hook 山字钩double iteration procedure 双重迭代法double roller chock 双滚轮式导览钳double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索draft 吃水drag 阻力，拖拽力drainage 排水draught 吃水，草图，设计图，牵引力dredge 挖泥船drift 漂移，偏航drilling rig 钻架drillship 钻井船drive shaft 驱动器轴driving gear box 传动齿轮箱driving shaft system 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力，供给量electrohydraulic 电动液压的electroplater 电镀工elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力endurance 续航力，全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配，安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint 伸缩接头extrapolate 外插fair 光顺faised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮，渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 水火管锅炉fixed-pitch 固定螺距式flange 突边，法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流flow pattern 流型，流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak 艏尖舱forged steel stem 锻钢艏柱forging 锻件，锻造forward draft mark 船首水尺forward/afer perpendicular 艏艉柱forward/after shoulder 前/后肩foundry casting 翻砂铸造frame 船肋骨，框架，桁架freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修gaff 纵帆斜桁gaff foresail 前桅主帆gangway 舷梯gantt chart 甘特图gasketed openings 装以密封垫的开口general arrangement 总布置general cargo ship 杂货船generatrix 母线geometrically similar form 外形相似船型girder 桁梁，桁架girder of foundation 基座纵桁governmental authorities 政府当局，管理机构gradient 梯度graving dock 槽式船坞Green Book 绿皮书，19世纪英国另一船级社的船名录，现合并与劳埃德船级社，用于登录快速远洋船gross ton 长吨（1.016公吨）group technology 成祖建造技术GT 成组建造技术guided-missile cruiser 导弹巡洋舰gunwale 船舷上缘gunwale angle 舷边角钢gunwale rounded thick strake 舷边圆弧厚板guyline 定位索gypsy 链轮gyro-pilot steering indicator 自动操舵操纵台gyroscope 回转仪half breadth plan 半宽图half depth girder 半深纵骨half rounded flat plate 半圆扁钢hard chine 尖舭hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖hatch cover 舱口盖板hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链桶hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的，螺旋状的hinge 铰链hinged stern door 艉部吊门HMS 英国皇家海军舰艇hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂，轴毂，套筒hull form 船型，船体外形hull girder stress 船体桁应力HV AC(heating ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的IAGG(interactive computer graphics) 交互式计算机图像技术icebreaker 破冰船icebreaker 破冰船IMCO(Intergovernmental Maritime Consultative Organization) 国际海事质询组织immerse 浸水，浸没impact load 冲击载荷imperial unit 英制单位in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle of inclination 小倾角初稳性inland waterways vessel 内河船inner bottom 内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的，加强的International Association of Classification Society (IACS) 国际船级社联合会International Towing Tank Conference (ITTC) 国际船模试验水池会议intersection 交点，交叉，横断（切）inventory control 存货管理iterative process 迭代过程jack 船首旗jack 千斤顶joinery 细木工keel 龙骨keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launch 发射，下水launch 汽艇launching equipmeng （向水中）投放设备LCC 大型原油轮leading edge 导缘，导边ledge 副梁材length overall 总长leveler 调平器，矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship 空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier 液体散货船liquid chemical tanker 液体化学品船list 倾斜living and utility spaces 居住与公用舱室Lloyd’s Register of shipping劳埃德船级社Lloyd’s Rules劳埃德规范Load Line Convention 载重线公约load line regulations 载重线公约，规范load waterplane 载重水线面loft floor 放样台longitudinal (transverse) 纵（横）稳心高longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向菱形系数longitudinal strength 纵总强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械（主机）卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板maritime 海事的，海运的，靠海的mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船Merchant Shipbuilding Return 商船建造统计表metacenter 稳心metacentric height 稳心高metal plate path 金属板电镀槽metal worker 金属工metric unit 公制单位middle line plane 中线面midship section 舯横剖面midship section coefficient 中横剖面系数ML 物资清单，物料表model tank 船模试验水池。
船舶常用词汇
载重量Deadweight tonnage (DWT)在一定水域和季节里，运输船舶所允许装载的最大重量，包括载货量、人员（旅客和船员）及其行礼、食品、淡水、燃料、润滑油、炉水、备品和供应品等的重量，又称总载重量。
载重量表征了船舶的等级大小和运输能力，是船舶的主要参数之一。
一般来说，载重量与相应的季节、吃水相对应。
如果不作特别说明，多指夏季满载吃水情况下的总载重量。
总载重量等于满载排水量扣除空船排水量。
净载重量Net DWT在一定的水域和季节里，船舶所能装载的最大限度的货物重量。
船舶常数是指船舶营运一段时间之后的空船重量与船舶出厂时空船重量之差。
其中包括燃油舱、压载舱等液柜中排不出的残余物、船上库存的破损机件的重量等。
总吨位Gross tonnage (GT)根据《国际船舶吨位丈量公约》的有关规定，丈量后确定的船舶总容积，又称总吨。
以吨位表示。
总吨位一般用于：表示船舶大小；表示一国或一家船公司拥有船舶的数量；计算造船费用、船舶保险费用；在有关的国际公约和船舶规范中用来区别船舶的等级以衡量对技术管理和设备要去的标准；有的国家用作造船补助金、航海补助金等的计量标准；以及用作船舶登记、检验和丈量的收费标准等。
净吨位Net tonnage (NT)根据《国际船舶吨位丈量公约》的有关规定，从总吨位中减除不适于载运容、货处所而得到的船舶有效容积。
以吨位表示、净吨位一般用于交付港口费、引航费、灯塔费和停泊费的计基准。
航经苏伊士运河和巴拿马运河船舶的通行税也按净吨位收费。
Notification of inspection 检查验收通知单Application 申请，申请单Inspection 检验，报验Technical discussion 技术讨论On board(伙食费) 在船上In the workshop 在车间On the slipway 在船台上At pier(wharf) 在码头Fair 尚好的The performance is merely fair 性能尚好Terrible 极坏的，很糟的So so 马马虎虎So far ,so good 到目前，一切顺利Worse更糟的worst最差、最糟Improvement 改进Leave no room for improvement 完美，无缺点Accept 接收Accept subject to 有条件的接收，有待于……做好之后才接收Reject 拒收Comments 意见defect list 消除意见清单Item 项目memorandum 备忘录manual n、手册、说明书；a.手控的，手工的drawings 图纸working drawings 施工图finished drawings 完工图approved drawings 认可图drawings for approval 送审认可图supporting technical documents 基础技术文件sketch 草图draw a sketch画草图up to the standard 达到标准substandard 低于标准的crane 吊车building berth 船台slipway 船台、下水滑道dry dock 干船坞pier 突码头、突堤wharf 码头along side (船)靠码头foreman 工长，领班coordinator 调度员inspector 检查员supervisor 管理人、监督人，监造人surveyor 验船师Hull 船体Forecastle 艏楼Stern 船尾Poop 艉楼Superstructure 上层建筑Foremast 前桅杆After mast 后桅杆Radar mast 雷达桅杆Main deck 主甲板Upper deck 上甲板Poop deck 艉楼甲板Accommodation deck 生活甲板Compass deck 罗经甲板Funnel 烟囱Bridge 桥楼，驾驶台Bridge wing 驾驶室翼桥Wheel house 驾驶室Engine room 机舱Engine control room 机舱集控室Catwalk 天桥、步桥Flying bridge （露天）航行驾驶室Rescue boat 救助艇Life boat 救生艇M/V merchant vessels 商船Naval Auxiliary vessel 军用船Naval Ship/war ship 军船Ice-breaker 破冰船Container vessel 集装箱船Oil tanker 油轮Products tanks 成品油轮Carrier 运输船、航空母舰、托架Chemical carrier 化学品运输船Liquefied gas carrier 液化气体船Liquefied natural gas carrier 液化天然气运输船Aircraft carrier/aeroplane carrier 航空母舰School ship/training ship 训练船Geophysical survey ship 地球物理勘探船Cruiser 巡洋舰、大型快船、游艇Canoe 独木船，皮舟Junk 平底中国帆船、舳板Gondola （意大利威尼斯的）一种狭长的平底船Yacht 快艇、游艇Fast boat 快艇Patrol boat 巡逻艇Anti-smuggling boat 缉私艇Torpedo boat 公安艇Ferry 渡船Catamaran 双体船Jet foil 喷水水翼艇Wing assisted vessel 地效船Draft forward 前吃水Draft middle 中吃水Draft after 后吃水Plimsoll mark/lineWaterline 吃水线Waterlines （型）水线Port 左舷Starboard 右舷Sagging 中垂、下垂、下挂（流）Hogging 中拱、上拱Derformation 变形Fairing 光顺、火工校正Hot work热工、明火作业section 分段、部分、剖面Block 分段Keel （船舶）龙骨Bilge keel 舭龙骨Power tool 带动力工具（风动或电动）Welder 电焊工Welding machine 电焊机A.C welding 交流（电弧）焊D.C welding 直流（电弧）焊Grinding 打磨Welding 电焊Spatters 飞溅（电焊）Under cut 咬口Sharp edge 快口Deflection 挠曲，变形Slag 渣Welding slag 电焊渣Automatic welding 自动焊Manual welding 手工焊Arc welding 电弧焊Gas shielded welding气体保护焊Inert gas arc welding惰性气体保护电弧焊Welding seam焊缝Bending machine 弯曲机Three-roll bending machine三芯弯板机Torsional box抗扭箱Void space空舱Cofferdam 隔离舱Bulwark舷墙，防浪板Wall墙壁Floor地板肋板Controllable pitch 可调桨Elastic coupling 弹性联轴节Bellow 波纹管Joint接头Gaskets垫片Fitting bolts 拂螺拴Chock 制动块、导缆器Chock fast 环氧垫块Foundation 底座、基座Mounting 装置、座、架Mount （常指火炮等武器的）座，架Vent pipe 透气管Sounding pipe探测管Vaporreturn line油气回路管Stripping line扫舱管Safety equipment 安全设备Life-saving equipment救生设备Cargo hold 货舱Cargo oil tank货油舱Cabin 船舱、舱室Room房间Store room储藏室Cold room冷库Fish room鱼库Meat room 肉库Provision room粮库Foam room 泡沫库CO2 room二氧化碳室Pump room泵室Battery room蓄电池室Radio room 报务室Galley 厨房Ventilation system 通风系统Fresh water piping system 淡水系统Sea water piping system 海水管系Water jacket水套Insulation materials绝缘材料Lagging绝缘材料、外套（锅炉、管子等）safety device 安全装置Fly wheel飞轮Floating floor 浮式地板Deckhead 天花板（指由甲板形成的）Ladder 梯子Vertical ladder直梯Inclined ladder斜梯Accommodation ladder舷梯Pilot ladder引水员；软梯Current电流Voltage电压Frequency频率Contact触点、触头Ballast镇流器Convertor变频器、换能器Conductor导体Semi-conductor半导体Rectifier整流器Transformer变压器Thermostat 恒温器Thermister热敏器Edison base 螺丝灯座、爱迪生灯座Bayonet base卡口灯座On-off开关（量）Analogue模拟，模拟设备Active analogue有源模拟、主动模拟Passive analogue无源模拟、被动模拟Dry contact无源模拟、干接触Buzzer蜂鸣器Button按扭，电扭Switch开关Main switch主开关Main switch board主配电板Cable 电缆Wire 电线Three-core cable三蕊电缆Clamp夹钳、夹具Clip 接线柱、线夹Alligator clip鳄鱼夹、弹簧夹Voltage drop 电压降Speed drop速度降低Black out 黑灯试验Power failure失电Setting point 设定点Adjust 调正（v）Adjustment调正（n）Oscillator振荡器、振动器Oscilloprobe示波器测试头Oscilloscope示波器、示波仪Resistor电阻、电阻器Potentiometer电位器、电势计Electrolysis电解（作用）Electrolyte电解质、电解液setting point of power surplus负载余量设定值test the power surplus setting point重载询问试验Surface preparation表面处理（清理工作）Blasting equipment喷漆（砂粒）装置Sand blasting 喷砂除锈Pre-blasting预喷砂Full blasting 通喷砂Sand sweep扫砂Sand blasting to SA2.5喷砂达到SA2.5级Steel work inspection after full blasting通喷砂后钢结构检查Cleanliness inspection清洁度检查Inspection after degreasing除去油脂后检查Removing oil stains by detergent/solvent使用洗洁剂/容剂除去油迹Shop primer 车间底漆Spray painting喷漆、喷涂法Touch-up 补漆、修正Touch-up painting补漆、点漆First coat 底漆、头道漆Finish coat 面漆Surface coat 表面涂层Under coat 内涂层Wearing coat 磨耗层Zinc-rich coating富锌涂层Cement wash coating（薄）水泥涂层Stripe coating 预涂层Floor covering 地板覆层Alkyd resin paint醇酸树脂漆Epoxy(resin-based)paint环氧树脂涂料Scuttle舷窗Carpet地毯Wooden skirt木裙板（踢脚）Aluminum skirt稆质裙板（踢脚）Brass nose装于楼梯踏步一的黄铜防滑镶条Stainless screw不锈钢螺钉Spring 弹簧Securing device固定件Locking device闭锁装置，制动设备Plywood胶合板，层压板Laminated plate迭层板Laminate层压制品，迭层板，层压板High pressure washing of the hull用高压水冲洗船壳Steel plate temperature 钢板温度Condensation冷凝Capillary condensation毛细管现象Dew point露点Flashing point闪点Ignition point 燃点，着火点Ventilation for coating 涂装通风Dehumidifier去湿机，干燥机Dehumidification 去湿，去潮Sagging流挂，下垂Chalking粉化Peeling剥落（指油漆）Pinhole针孔Curing硬化，熟化，硫化Drying film thickness(DFT)干膜（漆膜）厚度Curing temperature硬化、固化温度Power tools有动力的工具（包括电动及风动）Burnt area烧坏的区域Oil stains油迹Scratches划痕Damaged places遭损坏的部位Chicken wire钢丝网Tiles瓷砖，瓦Mosaic-tile彩色瓷砖，镶嵌瓷砖，马赛克瓷砖Glue胶，粘结剂Silica硅石，二氧化碳Silicagel硅胶Decoration装饰，装修Interior decoration内部装饰，内装Deck head 天花板Ceiling天花板Paneling板墙，镶板Wall墙壁Desk书桌，桌台Drawer 抽屉Catch hook固定钩子Observation window 观察窗Inspection window检查孔窗Clear view window旋转观察窗Curtain 窗帘Latch止动销，插销Valance窗帘箱Hanging窗帘Eyebrow舷窗眉板Pre-alarm预报警Trip脱扣，跳闸Preferential trip优先脱扣Transducer换能器synchronize（便）同步synchronous motor同步电机asynchronous motor异步电机step motor步进电机diode二极管triode三极管audion三极管single phase单相three phase三相phase-in逐步引进phase-shafting相移retarding phase 滞后相位reversed phase倒相，相反relay继电器timer定时器trimmer微调电容器，调正片delay延时transponder发射器，应答器，询问机echo-sound回声测深仪radio navigation equipment无线电导航设备log计程仪auto-pilot自动驾驶仪gyro-compass电罗经barrier屏障，障碍，栅栏zenner barrier齐纳屏（使电只能单向流的半导体）radio beacon无线电信标pulse脉冲blanking plus 消隐脉冲induction感应，感应现象oscillation振荡Leak(v)渗，漏Leakage(n) 渗，漏Overhaul大修，彻底检修Hammer榔头Spanner扳手，扳头Ring spanner环形扳手，梅花扳手Allen key 内六角扳手，Box spanner套筒扳手Torque spanner扭力扳手Double-ended spanner双头扳手Monkey spanner活络扳手，活络管扳手Shifting spanner活络扳手Pipe spanner管子扳手Reamer铰刀Reaming （用）铰（刀扩）孔Countersink reamer锥形孔铰刀Wrench扳手，扳头Calipers卡钳，两脚规Inside calipers内卡钳Bore 内孔Boroscopic inspection内孔表面检查Boroscope内孔表面检查仪Plug塞（子），（内燃机）火花塞Cock施塞，龙头Valve阀P/V valve P/V阀Strainer滤器Coarse strainer粗滤器Fine strainer精滤器Oil separator分油机Back pressure背压Pressure test压力试验Over speed 超速Over load超负荷Centering对中心Alignment对准，对准中心Inspection报验Installation安装Final inspection of M/E installation主机最终安装报验Inspection of the centering of the stern tube before fine boring精镗前艉轴管中心校准Alignment check/inspection拉中心/校正报验Completeness inspection of the thermal oil circulating piping system 热油循环管系完整性报验Cleanliness inspection after flushing F.O piping system燃油管串油后清洁检查Function test of steering gear舵机效甩试验Hose test of water tight doors水密门冲水试验Noise lever measurement噪声测量Vibration level measurement 振动测量Main engine (M/E)主机Generator发电机Emergency generator应急发电机Shaft generator轴带发电机Fresh water generator 制淡装置Steering gear 舵机General service pump总用泵Fire pump消防泵Hydraulic motor 液压马达Hydraulic nuts液压螺帽Rudder舵Rudder blade舵叶Propeller车叶，螺旋桨Fixed pitch propeller固定螺距的螺旋桨Ship船Vessel船，舰Fabrication制造，分段装配（prefabrication预制，预加工）Assemble装配，组装Erection大合拢，船台装配Staging脚手架Block stage分段阶段Mile stone（里程碑，大节点）Plate-cutting下料，开工Keel-laying上船台，龙骨铺设Launching下水mooring trial码头试验，系泊试验sea trial(sea)试航delivery of the ship交船defect list by the owner/society船东提出的消除意见清单/船级社提出的消除意见清单design stage设计阶段submit drawings to owner, classification society(LR、DNV、BV、ABS，etc)for approval向船东，船级社（劳氏，挪威，法国，美国等）提交认可图纸hull workshop船体车间machining workshop加工车间machinery engineering workshop轮机车间electrical workshop电气车间business dept.经营处purchasing dept.供应处Q.C.Dept.检验处Design dept.设计室Painting and carpenter’s workshop漆木车间Project manager项目经理Director指导者，厂长，董事Managing director执行董事，常务董事，总经理Head首长，团长，主任Manager经理，管理人，干事Leader领导者Meeting会议Negotiation谈判Agreement协议Shipyard船厂a faired set of lines 经过光顺处理的一套型线a stereo pair of photographs 一对立体投影相片abaft 朝向船体abandonment cost 船舶废置成本费用accommodation 居住（舱室）accommodation ladder 舷梯adjust valve 调节阀adjustable-pitch 可调螺距式admiralty 海军部advance coefficient 进速系数aerostatic 空气静力学的aft peak bulkhead 艉尖舱壁aft peak tank 艉尖舱aileron 副鳍air cushion vehicle 气垫船air diffuser 空气扩散器air intake 进气口aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼，翼剖面，机面，方向舵alignment chock 组装校准用垫楔aluminum alloy structure 铝合金结构American Bureau of Shipping 美国船级社amidships 舯amphibious 两栖的anchor arm 锚臂anchor chain 锚链anchor crown 锚冠anchor fluke 锚爪anchor mouth 锚唇anchor recess 锚穴anchor shackle 锚卸扣anchor stock 锚杆angle bar 角钢angle of attack 攻角angle plate 角钢angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷anti-pitching fins 减纵摇鳍antiroll fins 减摇鳍anti-rolling tank 减摇水舱appendage 附体artisan 技工assembly line 装配流水线at-sea replenishment 海上补给augment of resistance 阻力增额auxiliary systems 辅机系统auxiliary tank 调节水舱axial advance 轴向进速backing structure 垫衬结构back-up member 焊接垫板balance weight 平衡锤ball bearing 滚珠轴承ball valve 球阀ballast tank 压载水舱bar 型材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船baseline 基线basic design 基本设计batten 压条，板条beam 船宽，梁beam bracket 横梁肘板beam knee 横梁肘板bed-plate girder 基座纵桁bending-moment curves 弯矩曲线Benoulli’s law 伯努利定律berth term 停泊期bevel 折角bidder 投标人bilge 舭，舱底bilge bracket 舭肘板bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩blade root 叶跟blade section 叶元剖面blast 喷丸block coefficient 方形系数blue peter 出航旗boarding deck 登艇甲板boat davit 吊艇架boat fall 吊艇索boat guy 稳艇索bobstay 首斜尾拉索body plan 横剖面图bolt 螺栓，上螺栓固定Bonjean curve 邦戎曲线boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁bottom side tank 底边舱bottom transverse 底列板boundary layer 边界层bow line 前体纵剖线bow wave 艏波bowsprit 艏斜桅bow-thruster 艏侧推器box girder 箱桁bracket floor 框架肋板brake 制动装置brake band 制动带brake crank arm 制动曲柄brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸brake hydraulic pipe 刹车液压管breadth extreme 最大宽，计算宽度breadth moulded 型宽breakbulk 件杂货breasthook 艏肘板bridge 桥楼，驾驶台bridge console stand 驾驶室集中操作台BSRA 英国船舶研究协会buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulb plate 球头扁钢bulbous bow 球状船艏，球鼻首bulk carrier 散货船bulk oil carrier 散装油轮bulkhead 舱壁bulwark 舷墙bulwark plate 舷墙板bulwark stay 舷墙支撑buoy tender 航标船buoyant 浮力的buoyant box 浮箱Bureau Veritas 法国船级社butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例，按约定船舶专业英语词汇（按照字母顺序排列）（二）cable ship 布缆船cable winch 钢索绞车CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程camber 梁拱cant beam 斜横梁cant frame 斜肋骨cantilever beam 悬臂梁capacity plan 舱容图CAPP(computer –aided process planning) 计算机辅助施工计划制定capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容，载货容积cargo handling 货物装卸carriage 拖车，拖架cast steel stem post 铸钢艏柱catamaran 高速双体船catamaran 双体的cavitation 空泡cavitation number 空泡数cavitation tunnel 空泡水筒center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心，重心，质心，矩心chain cable stopper 制链器chart 海图charterer 租船人chief engineer 轮机长chine 舭，舷，脊chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论classification society 船级社cleat 系缆扣clipper bow 飞剪型船首clutch 离合器coastal cargo 沿海客货轮cofferdam 隔离舱combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船commuter 交通船compartment 舱室compass 罗经concept design 概念设计connecting tank 连接水柜constant-pitch propeller 定螺距螺旋桨constraint condition 约束条件container 集装箱containerized 集装箱化contract design 合同设计contra-rotating propellers 对转桨controllable-pitch 可控螺距式corrosion 锈蚀，腐蚀couple 力矩，力偶crane 克令吊，起重机crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱criterion 判据，准则Critical Path Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积crow’s nest 桅杆瞭望台cruiser stern 巡洋舰尾cruising range 航程cup and ball joint 球窝关节curvature 曲率curves of form 各船形曲线cushion of air 气垫damage stability 破损稳性damper 缓冲器damping 阻尼davit arm 吊臂deadweight 总载重量de-ballast 卸除压载deck line at side 甲板边线deck longitudinal 甲板纵骨deck stringer 甲板边板deck transverse 强横梁deckhouse 舱面室，甲板室deep v hull 深v型船体delivery 交船depth 船深derrick 起重机，吊杆design margin 设计余量design spiral 设计螺旋循环方式destroyer 驱逐舰detachable shackle 散合式连接卸扣detail design 详细设计diagonal stiffener 斜置加强筋diagram 图，原理图，设计图diesel engine 柴油机dimensionless ratio 无量纲比值displacement 排水量displacement type vessel 排水型船distributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠double hook 山字钩double iteration procedure 双重迭代法double roller chock 双滚轮式导览钳double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索draft 吃水drag 阻力，拖拽力drainage 排水draught 吃水，草图，设计图，牵引力dredge 挖泥船drift 漂移，偏航drilling rig 钻架drillship 钻井船drive shaft 驱动器轴driving gear box 传动齿轮箱driving shaft system 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力，供给量electro hydraulic 电动液压的electroplater 电镀工elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力endurance 续航力，全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配，安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint 伸缩接头extrapolate 外插fair 光顺raised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮，渡运航线fillet weld connection 填角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler火管锅炉fixed-pitch 固定螺距式flange 突边，法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可浸长度曲线flow of materials 物流flow pattern 流型，流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding hatch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak 艏尖舱forged steel stem 锻钢艏柱forging 锻件，锻造forward draft mark 船首水尺forward/after perpendicular 艏艉柱forward/after shoulder 前/后肩foundry casting 翻砂铸造frame 船肋骨，框架，桁架freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water load line 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修gaff 纵帆斜桁gaff foresail 前桅主帆gangway 舷梯gantt chart 甘特图gasketed openings 装以密封垫的开口general arrangement 总布置general cargo ship 杂货船generatrix 母线geometrically similar form 外形相似船型girder 桁梁，桁架girder of foundation 基座纵桁governmental authorities 政府当局，管理机构gradient 梯度graving dock 槽式船坞Green Book 绿皮书，19世纪英国另一船级社的船名录，现合并与劳埃德船级社，用于登录快速远洋船gross ton 长吨（1.016公吨）group technology 成祖建造技术GT 成组建造技术guided-missile cruiser 导弹巡洋舰gunwale 船舷上缘gunwale angle 舷边角钢gunwale rounded thick strake 舷边圆弧厚板gypsy 链轮gyro-pilot steering indicator 自动操舵操纵台gyroscope 回转仪half breadth plan 半宽图half depth girder 半深纵骨half rounded flat plate 半圆扁钢hard chine 尖舭hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖hatch cover 舱口盖板hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链筒hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的，螺旋状的hinge 铰链hinged stern door 艉部吊门HMS 英国皇家海军舰艇hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂，轴毂，套筒hull form 船型，船体外形hull girder stress 船体桁应力HV AC(heating ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的IAGG(interactive computer graphics) 交互式计算机图像技术icebreaker 破冰船icebreaker 破冰船IMCO(Intergovernmental Maritime Consultative Organization) 国际海事质询组织immerse 浸水，浸没impact load 冲击载荷imperial unit 英制单位in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle of inclination 小倾角初稳性inland waterways vessel 内河船inner bottom 内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的，加强的International Association of Classification Society (IACS) 国际船级社联合会International Towing Tank Conference (ITTC) 国际船模试验水池会议intersection 交点，交*，横断（切）inventory control 存货管理iterative process 迭代过程jack 船首旗jack 千斤顶joinery 细木工keel 龙骨keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launch 发射，下水launch 汽艇launching equipment （向水中）投放设备LCC 大型原油轮leading edge 导缘，导边ledge 副梁材length overall 总长leveler 调平器，矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship 空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier 液体散货船liquid chemical tanker 液体化学品船list 倾斜living and utility spaces 居住与公用舱室Lloyd’s Register of shipping 劳埃德船级社Lloyd’s Rules 劳埃德规范Load Line Convention 载重线公约load line regulations 载重线公约，规范load water plane 载重水线面loft floor 放样台longitudinal (transverse) 纵（横）稳心高longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向菱形系数longitudinal strength 纵总强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械（主机）卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板maritime 海事的，海运的，靠海的mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船Merchant Shipbuilding Return 商船建造统计表metacenter 稳心metacentric height 稳心高metal plate path 金属板电镀槽metal worker 金属工metric unit 公制单位middle line plane 中线面midship section 舯横剖面midship section coefficient 中横剖面系数ML 物资清单，物料表model tank 船模试验水池monitoring desk of main engine operation 主机操作监视台monitoring screen of screw working condition 螺旋桨运转监视屏more shape to the shell 船壳板的形状复杂mould loft 放样间multihull vessel 多体船multi-purpose carrier 多用途船multi-ship program 多种船型建造规划mushroom ventilator 蘑菇形通风桶mutually exclusive attribute 相互排它性的属性N/C 数值控制nautical mile 海里naval architecture 造船学navigation area 航区navigation deck 航海甲板near-universal gear 准万向舵机，准万向齿轮net-load curve 净载荷曲线neutral axis 中性轴，中和轴neutral equilibrium 中性平衡non-retractable fin stabilizer 不可收放式减摇鳍normal 法向的，正交的normal operating condition 常规运作状况nose cone 螺旋桨整流帽notch 开槽，开凹口oar 橹，桨oblique bitts 斜式双柱系缆桩ocean going ship 远洋船off-center loading 偏离中心的装载offsets 型值offshore drilling 离岸钻井offshore structure 离岸工程结构物oil filler 加油点oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water 敞水optimality criterion 最优性准则ore carrier 矿砂船orthogonal 矩形的orthogonal 正交的out strake 外列板outboard motor 舷外机outboard profile 侧视图outer jib 外首帆outfit 舾装outfitter 舾装工outrigger 舷外吊杆*头overall stability 总体稳性overhang 外悬paddle 桨paddle-wheel-propelled 明轮推进的Panama Canal 巴拿马运河panting arrangement 强胸结构，抗拍击结构panting beam 强胸横梁panting stringer 抗拍击纵材parallel middle body 平行中体partial bulkhead 局部舱壁payload 有效载荷perpendicular 柱，垂直的，正交的photogrammetry 投影照相测量法pile driving barge 打桩船pillar 支柱pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距pitch 纵摇plan views 设计图planning hull 滑行船体Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船poop 尾楼port 左舷port call 沿途到港停靠positive righting moment 正扶正力矩power and lighting system 动力与照明系统precept 技术规则preliminary design 初步设计pressure coaming 阻力式舱口防水挡板principal dimensions 主尺度Program Evaluation and Review Technique 规划评估与复核法progressive flooding 累进进水project 探照灯propeller shaft bracket 尾轴架propeller type log 螺旋桨推进器测程仪PVC foamed plastic PVC泡沫塑料quadrant 舵柄quality assurance 质量保证quarter 居住区quarter pillar 舱内侧梁柱quartering sea 尾斜浪quasi-steady wave 准定长波quay 码头，停泊所quotation 报价单racking 倾斜，变形，船体扭转变形radiography X射线探伤rake 倾斜raked bow 前倾式船首raster 光栅refrigerated cargo ship 冷藏货物运输船Register （船舶）登录簿，船名录Registo Italiano Navade 意大利船级社regulating knob of fuel pressure 燃油压力调节钮reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力reverse frame 内底横骨Reynolds number 雷诺数right-handed propeller 右旋进桨righting arm 扶正力臂，恢复力臂rigid side walls 刚性侧壁rise of floor 底升riverine warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇roll-on/roll-off (Ro/Ro) 滚装rotary screw propeller 回转式螺旋推进器。
(完整版)船舶常用词汇
船舶常用词汇Ship 船Vessel 船Shipyard 船厂Shipbuilding 造船m/v=multiple-purpose vessel 多用途船b/c=bulk carrier 散货船product oil tanker 成品油轮steel cutting 开工lofting 放样spiling 号料nesting 套料keel 龙骨flat keel 平板龙骨bilge keel 舭龙骨keel laying 上台launching/float out 下水dry docking 进坞sea trial 试航delivery 交船ceremony 仪式、典礼block 分段stage 阶段block stage 分段阶段fabrication 制造production 制造dept.=department 部门purchuse and sales dept. 经营供应部design dept. 设计部门quality 质量qc dept.=quality control dept 质量控制部门precision 精度pre-fabrication 预制assembly 装配installation/fitting 安装pre-assembly 预装配、小合拢block fabrication 中合拢erection 大合拢pre-erection 总组outfitting 舾装outfittings 舾装件painting/coating 涂装weld 焊接weld seam 焊缝erection joints 大接缝undercut 咬边overlap 焊瘤grind 打磨pin hole 气孔、砂眼sandblasting 喷砂acid washing 酸洗shot-blasting 喷砂shop primer 车间底漆sand hole 砂眼pitting 凹坑flange 法兰structure 结构welder 焊工grinder 打磨工certificate 证书abs certificate abs证书flux 焊剂wire 焊丝erpendicularity 垂直度、正交度flatness 平面度schedule 计划inspection 检验complete/completion 完工incomplete/incompletion 未完finish 完成confirm 确认approve 认可（动词）approval 认可（名词）coordinate 协调test 试验report 报告tight 紧密的watertight 水密oiltight 油密airtight 气密tightness test 密性试验leak 泄漏leak test 密性试验vacuum 真空vacuum test 真空试验flushing test 串油试验check 检验、检查final 最终的final inspection 完工检验defect 缺陷(动词)defection 缺陷(名词)crack 裂纹fracture 裂纹、骨折missing 漏了repair 修补alignment 矫正、错位cause 原因reason 原因drawing 图纸modify 修改(动词)modification 修改(名词)procedure 程序welding procedure 焊接程序sequence 顺序discuss 讨论specification 规格书clarify 说明、澄清problem 问题solve the problem 解决问题no problem 没问题inside=internal 内部的outside=external 外部的thickness 厚度diameter=dia. 直径radius 半径size 尺寸dimension 尺度main dimension 主尺度forward 前面的、前部ceramic 陶瓷棉backing 衬垫ceramic backing 陶瓷衬垫gouge 碳刨back gouge 清根clean 清洁grind 打磨surface 表面insulation 绝缘temperature 温度pre-welding 焊前pre-welding inspection 焊前检验post-welding 焊后u/t＝ultrasonic test 超声波探伤m/t＝magnetic test 磁粉探伤x-ray x射线、x光照片day 日子date 日期time 时间the day before yesterday 前天the day after tomorrow 后天yesterday 昨天tomorrow 明天before 在……之前after 在……之后hull 船体hull no.=ship no. 船号steel plate 钢板side shell 外板port side 左舷starboard 右舷bracket 肘板bulkhead 舱壁transverse bulkhead 横舱壁longitudinal bulkhead 纵舱壁corrugated bulkhead 槽形舱壁double bottom 双层底ballast 压载double bottom ballast tank 双层底压载舱water ballast tank 压载水舱wing water ballast tank边压载水舱fore peak tank 首尖舱cargo hold＝c／h 货舱fore 首部aft 尾部midship 船舯forecastle 艏楼poop 尾楼accommodation 住舱accommodation/superstructure上层建筑deck 甲板main deck 主甲板tween deck 中间甲板upper deck 上甲板lower deck 下甲板forecastle deck 首楼甲板poop deck 尾楼甲板weather deck 露天甲板captain 船长captain deck 船长甲板mast 桅fore mast 首桅hatch coaming 舱口围板crane 克令吊deck crane 甲板克令吊hatch cover＝h／c 舱口盖semi-auto cutting 半自动切割n/c cutting 数控切割boring 镗孔rough 粗糙的rough boring 粗镗孔final boring 精镗孔shaft 轴tail shaft 尾轴bearing 轴承clearance 间隙machinery 轮机、机械electrical 电器的stern tube 尾管casting 铸锻件steel casting 铸钢件shaft line 轴线pipe 管子piping 管系oil 油lubricate oil piping=l.o. piping 滑油管系fuel oil piping=f.o. piping 燃油管系rudder 舵rudder horn=rh 挂舵臂rudder stock 舵杆rudder pintle 舵梢steering gear=s/g 舵机mooring 系泊winch绞车mooring winch系泊绞车anchor锚windlass锚绞机mooring test系泊试验propeller螺旋桨engine room=e/r机舱ecr＝engine control room机舱集控室main engine=m/e主机aux.liary engine＝aux. engine＝a／e 付机generator发电机emergency 紧急的emergency generator应急发电机shaft generator轴带发电机escape逃跑emergency escape应急逃生口exit出口emergency exit应急出口manhole 人孔manhole cover人孔盖hydraulic液压的hydraulic pipe液压管cut out开口、切口accomodation ladder舷梯ceiling天花板drain pipe落水管、排污管scallop扇形孔、落水孔sounding pipe测深管echo sounder测深仪238．speed log计程仪remote遥远的controll控制remote controller遥控器system系统remote controll sounding system 测深遥控系统air空气air conditioner空调compressor压缩机247．f.o. overflow tank燃油溢流柜（舱）meeting room会议室galvanize渡锌zinc锌rust生锈rust-proof oil防锈油sea chest海水吸入箱root gap 根部间隙deadline最后期限launching deadline下水最后期限full penetration welding 全熔透焊deep penetration welding深熔透焊filter滤器strainer滤器sea water海水sea water filter海水滤器parallel 平行freefall boat尾抛艇rescue boat救助艇lifeboat救生艇lifejacket救生衣liferaft救生阀stability稳性endurance耐久性、续航力drilling钻孔fitting and lapping拂配273．manhole 人孔manhole cover人孔盖air hole透气孔、气孔open开opening开口access opening入口、入孔clear opening净孔尺寸mooring chock系缆钳mooring lines系缆crane post克令吊座crane jib克令吊吊臂spray gun喷枪base line＝b.l.基线center line=c.l.中心线accommodation ladder舷梯embarkation ladder登船梯vertical ladder竖梯general arrangement 总布置assignment 指定，分配space 处所，空间access 通道，入口allocation 分配，配置furnishings 家具conceptual(design) 概念（设计）preliminary(design) 初步（设计）contract (stage) 合同（阶段）working plan 施工图melding 融合coordinate relationship 协调关系division 部门，划分efficient and economical way 有效和经济的方式speciality 专业feed-in 送进，提供specifications 各种技术条件，说明书uptake 烟道commercial transportation 商业运输solid (liquid) bulk type 固体（液体）散装型ferryboat 渡船transoceanic 远洋的profit 利益annual cost 年度费用terminal allocation 码头配置费overhead 管理费杂项开支component 组成部分characteristic 特性mechanical 机械的goods 货物marine terminal 港口码头enclosing volume 密闭容积hull envelope 船体外壳primary strength 总强度stowage 配载housing 容纳diagram 图表superstructure 上层建筑machinery space 机舱miscellaneous (其他)杂用舱室watertight subdivision 水密分舱integrity 完整性tankage 液舱，容积（量）clean ballast 清洁压载lines plan 型线图cruising range 巡航范围margin line 限界线floodable length curve 可浸长度尺寸layout 草图peak bulkhead 尖舱舱壁regulatory body 主管机构intact stability 完整稳性trade-off 权衡，折中interior arrangement 舱室布置stairway and passageway arrangement梯道及走道布置interior / exterior passageway 内外走道bridge deck 驾驶甲板compass deck 罗经甲板boat deck 艇甲板accommodation deck 起居甲板vehicle deck 车辆甲板winch platform 起货机平台wheel house 驾驶室chart room 海图室radio room 报务室coding room 译电室mast house 桅室captain’s room 船长室crew’s room 船员室cabin 客舱main engine control room 主机操纵室auxiliary engine room 副机舱boiler room 锅炉舱steering engine room 舵机舱workshop 机修间store 储藏室fore / aft peak 首/尾尖舱top side / bottom side tank 顶边/底边舱wing tank 边舱steering gear 操舵装置anchor and mooring arrangement 锚泊及系缆设备hawse pipe 锚链筒chain locker 锚链舱hatch cover 舱口盖lifesaving equipment / appliance 救生设备mast 桅rigging 索bollard 双柱带缆桩bitt 带缆桩fairlead 导缆孔ship lines 船体线型ship form 船体形状drawing 图lines plan 型线图orthogonal plans 正交平面body section 横剖面body plan 横剖线图symmetry 对称water lines/level lines 水线，水平型线half breadth plan 半宽水线图view 视图sheer profile 侧视图，纵剖线图buttocks 后体纵剖线bow lines 前体纵剖线after/fore body 后/前体alteration 修改，变更fairing process 光顺过程wooden/plastics batten 木质/塑料压条drawing office 制图/设计室mould loft 放样间full size 实尺loft floor 放样台lofting 放样steel pin 铁钉screw 螺钉wing shaft 侧轴shaft bossing 轴包套casting 铸件shaft bracket 轴支架parallel middle body 平行中体full slow ship 丰满的低速船fine fast ship 尖瘦的快速船entrance 进流段，入口run 去流段，流向forward/after shoulder 前/后肩“sheer profile 侧视图toilet /lavatory / toilet bowl 恭桶,坐便器toilet paper holder 卫生纸架toilet seat 恭桶座圈cistern 水箱hand towel 毛巾grab bar 防浪扶手wash basin, hand basin 面盆shaver outlet, shaver point 剃须刀插座bath towel 浴巾shower 淋浴喷头soap dish 浴皂盒tumbler holder 杯架toilet brush holder 厕刷架sink drain 落水管ball-float toilet 浮球阀式恭桶flush, handle, 低水箱扳手ball-cock assembly 浮球阀sanitary unit/ wet unit/bath unit 卫生单元top frame 上门槛clear opening 门通道silicon 硅胶scupper 地漏fresh water pipe 淡水管conduit pipe 导管water closet, w.c. 厕所；抽水马桶socket 插座plug 插头bulb 灯泡lampshade 灯罩wall lamp 壁灯electric fan 电扇toilet paper, toilet roll 卫生纸toilet cover 恭桶盖tank 低水箱bathroom cabinet 卫生间镜箱towel rack, towel rail 毛巾架folding seat 折叠架faucet / tap / mixing battery 水龙头bathtub, bath 浴缸faucet, mixer tap 明三联式浴缸水嘴shower curtain 浴盆帘hook 挂钩ashtray 烟灰缸tile 瓷砖trap 存水弯tank lid 水箱盖,float ball 浮球inlet tube 进水管adjustable screw 调节螺丝bottom frame 下门槛handle 把手floor pan 底盘outlet water 洗脸盘出水管connection 连接件door hinge 门铰链switch 开关furniture 家具berth 卧铺locker 有锁橱柜chest 箱柜drawer 抽屉double tier berth 双层床mattress 床垫clothes locker 带锁衣橱curtain 窗帘bookrack 书架coat hook 衣帽钩public space 公共区域corridor 走廊stairway 梯道carpet 地毯antiskid 防滑装置ceramic-tile 瓷砖mat 垫子interior door 内室门fire-retardant 耐火的self-closer 自闭器steel mesh door 钢质钢丝网门steel watertight door 钢质水密门latch 门插销refrigerator 冰箱wardrobe 衣柜dressing table 梳妆台stool 凳子bookshelf 书架carpet 地毯waste-paper basket 废纸篓blanket 毯子fireproof door 防火门partition wall 独立围壁master key 万能钥匙threshold 门槛casing 罩壳name plate 名牌frame 门框brass plate 黄铜名牌scuttle 舷窗rotate 旋转clear-view screen 清屏器window-wiper 擦窗器safety glass 安全玻璃insulation 绝缘upholstery 室内装潢curtain 窗帘门帘stuffing 填塞料settee 靠背长椅polyester foam 聚脂泡沫textile 纺织品darkening curtain 遮光帘composite rock wool panel 复合岩棉板lining 里层ceiling 天花板non- combustible 不燃的galvanize steel sheet 镀锌铁皮sideboard 边柜plywood 夹板plastic laminate 塑料压板storm fiddle 风暴挡板tea table 茶几easy chair 轻便椅cushion 垫子bench 条凳louver 百叶窗door frame 门框door leaf 门扇baked paint 烘漆captain 船长chief mate 大副second mate 二副third mate 三副bosun 水手长chief engineer 轮机长second engineer 大管third engineer 二管tally clerk 理货员pilot 引水员repairer 修理员steward 服务员fireman 消防员cadet 实习员cook 炊事员wiper 清洁工oiler 加油工fitter 钳工electrician 电工administrator 管理员super cargo 押运员pantry 配餐间gallery 厨房living room 起居室day room 休息室mess room 餐厅drying room 烘衣间laundry room 洗衣间bonded store 封关室dry provision 干货室hobby room 娱乐室rope store 缆索舱beverage store 饮料间linen store 被服间pantry 配餐间gallery 厨房living room 起居室day room 休息室mess room 餐厅drying room 烘衣间laundry room 洗衣间bonded store 封关室dry provision 干货室hobby room 娱乐室rope store 缆索舱beverage store 饮料间linen store 被服间pantry 配餐间gallery 厨房living room 起居室day room 休息室mess room 餐厅drying room 烘衣间laundry room 洗衣间bonded store 封关室dry provision 干货室hobby room 娱乐室rope store 缆索舱beverage store 饮料间linen store 被服间pantry 配餐间gallery 厨房living room 起居室day room 休息室mess room 餐厅drying room 烘衣间laundry room 洗衣间bonded store 封关室dry provision 干货室hobby room 娱乐室rope store 缆索舱beverage store 饮料间linen store 被服间pantry 配餐间gallery 厨房stainless steel 不锈钢checked plate 花钢板bevel 坡口boundary 边界intersection 相交，横断gravity 密度connect 固定remained plate 另板attachment 附件Free flange 自由边taper 斜度，锥度Mould line 理论线scallop 开孔Bend 弯曲snip 剪切stage 阶段opposite 对立的accessible 可达到的excess 余量margin 边缘thickness 厚度lap 搭接gouge 刨槽shrinkage 收缩Welding throat 焊喉Welding leg 焊脚reinforcement 焊缝凸量comparison 对照Fillet welding 角焊Spot welding 点焊Tack welding 定位焊Penetration welding 熔透焊Slot welding 塞焊Welding joint 焊接接头stress 应力concentrate 集中temporary 临时Automate weld 自动焊Manual welding 手工焊Bevel welding 坡口焊Partial Penetration welding 局部熔透焊Loose plate 散装板range 范围casting 铸件knuckle 折角Intercostals structure 连续构件workmanship 制造质量Welding defect 焊接缺陷narrow 狭窄Backside welding 背面衬垫焊Water stop hole 止漏孔resolution 解决deformation 变形asbestos 石棉ceramic 陶瓷gravity 重力Welding rod 焊条Sour to wash 酸洗zinc pipe 镀锌flange 法兰elbow 弯头blow 螺栓Varnish 油漆dugout 独木舟barge 驳船kayak(爱斯基摩人的)木排outrigger 桨叉架船rowing boat 划艇(美作:rowboatgondola (意大利的)长平底船whale mother ship 捕鲸母船hydrofoil 水翼船catamarans双体船dredger 挖泥船boat 船brig, brigantine 双桅船canoe 小船,独木舟caravel 快帆船cargo boat 货船coaster 近海贸易货船cod-fishing boat 捕鳕鱼船whaler 捕鲸船collier 运煤船battleship 战船shallop 小型战船coastguard cutter, coastguard vessel巡逻艇,缉私艇revenue cutter 缉私船patrol boat 巡逻艇minelayer 布雷艇minesweeper 扫雷艇torpedo boat 鱼雷艇frigate 轻护航舰gunboat 炮舰submarine 潜水艇destroyer 驱逐舰corvette 轻巡洋舰cruiser 巡洋舰aircraft carrier 航空母舰ferry, ferryboat 渡船,渡轮fishing boat 渔船freighter货船galleon 大型帆船galley 大划桨船hovercraft 气垫船icebreaker破冰船launch 艇lighter 驳船liner, ocean liner merchant ship,远洋班轮merchantman 商船motorboat 摩托艇outboard 尾部装有马达的小艇paddle steamer, paddle boat 明轮船passenger boat 客船piragua, pirogue 独木舟raft 木筏rowing boat 划艇sailing boat, sailing ship 帆船schooner 纵帆船ship 船skiff 小艇sloop 单桅船steamer, steamship 汽轮tanker 油轮trawler 拖网渔船tug, tugboat 拖轮vessel 船yacht 游艇yawl 船载小艇boat, ship 船(passenger) liner 邮轮, 客轮sailing boat, sailing ship 帆船yacht 游船(ocean) liner 远洋班轮packet boat 定期客船, 班轮cabin 船舱hovercraft 气垫船life buoy 救生圈lifeboat 救生艇life jacket 救生衣berth, cabin, stateroom 客舱first-class stateroom (cabin) 头等舱second-class stateroom (cabin) 二等舱steerage, third-class 三等舱steerage 统舱gang-plank 跳板crossing 横渡cruise 游弋to embark, to ship 乘船lifeboat救生艇to sail at a speed of 20 knots, 航速为20节to disembark 上岸on board a ship, aboard 在船上to stop over at... 中途在…停留anchor 锚ballast 压舱物beam 船辐(船的宽度)berth, bunk 舱位berth, cabin, stateroom 客舱bilge 船腹,船底污水bow, prow 船首bulwark 舷墙draught marks (美作:plimsoll mark)吃水标water line 吃水线upper deck 上甲板lower deck 下甲板keelson 内龙骨blade 桨片oars 桨, 橹stern 船尾starboard 右舷port 左舷thwart 划艇座板davit 吊锚柱water bowline 帆脚索bridge 船桥bull's eye 舷窗bulwark 甲板上的船舷capstan 起锚机cathead 船首锚架compass 罗盘conning tower 指挥塔cutwater 船首分水deck 甲板engine room 轮机舱figurehead 破浪神,船首饰forecastle 船首楼funnel 烟囱galley 厨房gangplank 跳板gangway 通道,跳板steerage 统舱to land 抵岸to transship 换船to board a ship; to embark; to go aboard上船to disembark from a ship, to go ashore,to land 下船grapnel, grappling iron 钩锚gun turret 炮塔gunwale, gunnel 船舷上缘hammock 吊床hatchway 舱口,升降口hawsehole, hawse 锚链孔helm 舵hold 货舱hull 船身lantern 信号灯length 长度logbook 航海日志midship 船中部midship frame 中部肋骨oar 桨oarlock, rowlock 桨架orlop 最下层甲板periscope 潜望镜poop, stern 船尾poop deck 尾楼gun port 炮门porthole 舷窗powder magazine 火药库quarterdeck 后甲板rudder 舵screw, propeller 推进器,螺旋桨scuttle 小舱口port side 左舷starboard 右舷sternpost 船尾骨storeroom 储藏室tiller 舵杆torpedo tube 鱼雷发射管waterline 水线,吃水线windlass, winch 吊车,提物机stem 船首block \ section 分段section 部面higher tensil steel 高强度welding line 焊道welding leg 焊脚fill weldimg 补焊weldimg symbol 焊接符号tapper symbol 削符号flat steel of ball 球扁钢steel plate 钢板angle steel 角钢circle steel 圆钢grind 打磨steel -graphitc gasket 不锈钢石墨垫片nonpoisonous silicom rubber 无毒橡胶teflon gasket 塑料王垫片tesent bed-ba-unit gasket 特力垫片material 材料exhaust gas piping 排气管the drinking and supplying piping 饮水和供水系统china classification society 中国船级社application list for vessel inspection 船舶报检单 checked by 检验员inspector's opinion 监造师意见surveyor''s opinion 验船师意见quality control department 质管科the record of inspectionsmeasurements and tests 检查,测量,试验记录program of sea trials 试航大纲hull structures 船体结构strength deck plating 加强板stringer plate 连接板keel plate 龙骨板sind sheel plating 边外形板bilge plating 底板bottom shell plating 底外板sheer strake longitudinal 避开船底板纵向deck longitudinal 甲板纵向longitudinal bulkhead top strake纵向顶部隔板bottom girders 底部桁deck transverse centre tank 甲板横向中间舱bottom transverse centre tank底部横向中间舱deck transverse wing tank 甲板横向边舱sind sheel vertical web 边外形板垂直网cross ties 交叉连接double bottom floor 双底板hatch coamings 舱口栏板manhole coaming 入孔围板centre cargo tank deck transverse中间货舱甲板横向horizontal girder 水平桁hopper web plating 漏斗网板bracket toe 支架脚lug 柄horizontal stringer 水平线串连vertical stiffener 垂直的抗挠件topside tank 顶边舱boardsind 舷侧elbow plank 肘板port 舷keel 龙骨rib 肋骨pillar 支柱hose joint 软管接头bronze 青铜galv seamless steel pipe 镀锌无缝钢管instrallation 装船Laundry room 洗衣房Drying room 烘干室fax machine 传真机corolless telephone 无线电话wages 工资solenoid 电磁阀flow swich 流量开关differential pressure 压差开关bunket station 加油站level gauging meter 液位指示表indication lamp for valve 阀位指示top vent 透气sewage holding tank 类便柜extension alarm 延伸报警composite boiler abnormal 组合锅炉故障mimic display 模拟显示master clock 母钟start prermit 允许起动start request 起动请求bow thruster 侧推disconnect 跳闸clopper log 计程仪rudder angle 舵角指示器slave clock 子钟tight rubber layer 密封橡胶sunk screw 固定螺钉weather tight ventilator 水密围井weather tight cover 水密盖gemel 铰链sharp edge 毛刺oil content 油份sensor for measuring salt 盐度计torpedo tube 鱼雷发射管waterline 水线,吃水线windlass, winch 吊车,提物机stem 船首。
船舶英语词汇
船舶英语词汇目录一、造船部分1、船体部分2、机舱部分3、电气部分4、船装部分二、造机部分三、修造部分一、造船部分1、HULL PART 船体部分1、1 结构Structure船厂dockyard/shipyard 船坞dock/boatyard 船东ship-owner 船舷Ship's side船码头quay/dock 船的栏杆Ship's rail 船舱hold 甲板Deck船籍Ship's registry 住舱甲板accommodation deck 船首bow 梁拱甲板arch deck船梯ladder 载货甲板cargo deck 船尾stern 首楼甲板Forecastle deck 上甲板Upper deck 下甲板Lower deck 主甲板Main deck 货舱甲板Hold deck桥楼甲板Bridge deck水密甲板Watertight deck驾驶甲板Navigation deck 铜-钢复合板Copper sheathing steel plate艇甲板Boat deck 甲板边板Deck stringer plate罗经甲板Compass deck 斜板Sloping plate 板Plate 加强板Reinforcement plate舭板Bilge plate 舵板Rudder plate船底板Bottom plate 舷侧外板Side plate 船外板Shell plate 裙板Skirt plate船首外板Bow plate 首柱板Stem plate肘板Bracket plate 首柱板Stern plate舱壁板Bulkhead plate 平台platform槽形舱壁板Corrugated bulkhead plate 机舱平台Engine-room platform舷墙板Bulwark plate 分段Block围板Coaming plate 首段Bow block连续板Connection plate 中段Midship block尾段Stern block 甲板下纵桁Underdeck girder 左舷port 舭纵桁Wing girder右舷Starboard 支柱Pillar纵桁Girder 肋骨Frame型材桁Bar girder 基础台架Base frame中底桁Bottom center girder 支架Bear frame中内龙骨Bottom center line girder 舭肋骨Bilge frame底桁材Bottom girder 船底肋骨Bottom frame旁桁材Bottom side girder 首肋骨Bow frame甲板纵桁Deck girder 肘板框架肋骨Bracket frame横桁Cross girder 球鼻首肋骨Bulbous bow frame水平桁Horizontal girder 球曲型肋骨Bulbous frame舱口边梁Hatch coaming girder 主肋骨Chief frame机座纵桁Engine girder 首肋骨Fore frame桁架梁Girder frame 舭纵桁舭纵骨Bilge longitudinal舯部肋骨Middle frame 船底纵骨/纵桁bottom longitudinal尖舱肋骨Peak frame 船底腹板纵桁bottom web longitudinal加强筋Stiffened frame 甲板纵桁Deck longitudinal横框架肋骨Transverse frame 内底纵桁/纵骨Inner bottom longitudinal肋距F.S.(frame space) 舷侧纵桁/纵骨Shell side longitudinal纵桁/纵骨/纵向构件longitudinal双层底顶纵骨Top longitudinal of double bottom斜舱壁纵骨Slopping-bulkhead longitudinal舱舷边舱Tank Wing tank结构structure 尾尖舱after peak tank附属结构Accessory structure 尾部水舱after water tank全焊结构All-welded structure 辅助水柜Auxiliary water tank中部结构Amidships structure 辅助压载水舱Auxiliary water ballast tank 泊位结构Berthing structure 污水舱Bilge tank底部龙骨结构Bottom keel structure 底舱Bottom tank船首部结构Bow structure 底边舱Bottom side tank支撑结构Braced structure 货油压载舱Cargo and ballast tank桥楼结构Bridge structure 循环水槽Circulating flow water tank首楼结构Forecastle structure 循环滑油舱压载水舱Circulating lubricating oil tank Ballast water tank构架结构Framed structure 清洁压载舱Clean ballast tank纵桁结构Girder structure 冷凝水柜Condensate catch tank人孔manhole 干舱Dry tank饮用水舱Drinking water tank 密封圈Sealing ring污水舱Bilge tank 铰链Hinge应急淡水柜Emergency fresh water tank 把手Handle首舱Fore tank 平衡块Balance block首尖舱Fore peak tank斜边舱Hopper side tank 1、2 welding 焊接液舱Liquid tank 坡口groove龙骨舱Keel tank 单面坡口Single groove右舷舱Starboard tank 双面坡口Double groove顶边水舱Topside tank Ⅰ形坡口Square groove顶边翼舱Topside wing tank V 型坡口Single v groove小舱口盖Small hatch cover U 型坡口Single u groove水密舱口盖Water-tight small hatch coverX 形坡口Single v groove风雨密舱口盖Weather-tight small hatch coverK 形坡口Single bevel grooveY 形坡口Single v groove with broad rood face填充金属Filler metal坡口面Groove face 热影响区Heat-affected zone(HAZ)坡口角度Groove angle 过热区Overheated zone焊缝倾角Weld slope 焊合线Bond line(fusion line)接头根部Root of joint 焊接区Weld zone根部间隙Root gap 焊缝区Weld metal area钝边Root face 焊缝weld焊接接头Welding joint 连续焊缝Continuous weld对接接头Butt joint 断续焊缝Intermittent weld角接接头Corner joint 纵向焊缝Longitudinal weldT 形接头T-joint 横向焊缝Transverse weld搭接接头Lap joint 对接焊缝隙Butt weld十字接头Cross shaped joint 角焊缝Filled weld母材Base metal(parent metal) 并列断续角焊缝Chain intermittent fillet交错断续角焊缝Staggered intermittent fillet弧焊整流器Arc welding rectifier焊缝正面Face of weld 自动焊Automatic welding焊缝背面Back of weld 埋弧自动焊Submerged arc welding焊缝宽度Weld width 半自动焊Semi- automatic welding焊缝长度Weld length 氩弧焊Argon-arc welding焊缝余高Reinforcement 二氧化碳气体保护焊CO2 gas shielded arc welding 焊脚Leg(of a fillet weld) 氧乙炔焊Oxy-acetylene welding焊脚长度Leg length 气割Gas cutting套管接头Muff joint 碳弧气刨Carbon arc air gouging手工电弧焊Manual arc welding(shielded metal arc welding)水下切割Underwater cutting直流电弧焊Direct current arc welding 等离子弧切割Plasma arc cutting交流电弧焊alternating current arc welding连续焊Continuous welding弧焊变压器Arc welding transformer 断续焊Intermittent welding点焊Sport welding对接焊Butt welding 分段退焊Back step welding角焊Fillet welding 分段多层焊Block welding搭接焊Lap welding 深溶焊Deep penetrating welding返修焊Re-welding 跳焊Skip welding补焊Repair welding 陶质衬垫焊Ceramic backing welding定位焊Tack welding 引弧Striking the arc封底焊Back sealing welding 焊接工艺参数Welding condition打底焊Backing welding 焊接电流Welding current堆焊Surfacing(overlaying) 焊接电压Welding voltage塞焊Plug welding 焊接速度Welding speed槽焊Slot welding 电弧电压Arc voltage盖面焊Consmetic welding 焊丝间距Wire spacing前倾焊Forward welding 空载电压Open circuit voltage后倾焊Backward welding 熔化速度Melting rate送丝速度Wire feed rate 层间温度Inter-pass temperature气体流量Gas flow rate 焊后热处理Post-weld heat treatment焊丝伸出长度Wire extension 锤击Peening极性Polarity 全焊透Full penetration welding正极/阳极Positive electrode 熔池Weld-pool负极/阴极Navigate electrode 熔深Penetration左焊法Leftward welding 弧长Arc length右焊法Rightward welding 喷射过渡Spray transfer电流密度Current density 短路过渡Short circuiting transfer线能量Heat input 熔滴过渡Metal transfer预热Preheat 焊缝成形Appearance of weld后热Post-heat 焊缝成形系数Form factor of weld预热温度Preheat temperature 熔敷系数Deposition coeffcient后热温度Post-heat temperature 熔敷效率Deposition efficiency熔合比Penetration ratio 立焊Vertical position welding等速送丝Constant wire-feed system 仰焊Overhead position welding 变速送丝alternate wire-feed system 立向上焊Vertical up welding 电弧静特性Static characteristic of arc立向下焊Vertical down welding电弧动特性dynamic characteristic of arc单面焊Welding by one side焊接性试验Weldability test 双面焊Welding by both side焊接结构Welded construction 单道焊Single-pass welding焊道Bead 多道焊Multi-pass welding焊层Layer 多层焊Multi-layer welding正接（正极性）Straight polarity 焊接材料Consumables反接（反极性）Reversed polarity 焊条Electrode焊接位置Position of welding 焊条药皮Coating平焊Flat position welding 酸性焊条Acid electrode横焊Horizontal position welding 碱性焊条Basic electrode低氢型焊条Low hydrogen type electrode 焊丝盘Wire reel铁粉性焊条Iron power type electrode 铜冷却板Cu-cooling plate重力焊条Gravity electrode 铜滑块Copper shoe焊剂Flux 切割Cutting熔炼焊剂Fused flux 焊接工作台Welding bench烧结焊剂Sintered flux 焊接变位机Positioner焊丝Wire 送丝机构Wire feeder药芯焊剂Flux-cored wire 行走机构Traveler保护气体Shielded gas 焊接车间Welding shop焊剂垫Flux backing 引弧板Run-on tab(end tab)重力焊条Gravity electrode 引出板Run-off tab(end tab)焊剂漏斗Flux-hopper 定位板Strong-back流量计Flow meter 焊接衬垫Welding backing干燥箱Dryer 敲渣锤Chipping hammer面罩Helmet 条虫状气孔Wormhole焊工手套Welding glove 密集气孔Porosity焊钳Electrode holder 针尖状气孔Pinhole焊枪Welding gun 白点Fish eye (flake)导电嘴Tip 切口Kerf喷嘴Nozzle 咬边Undercut焊矩Torch 焊瘤overlap焊接缺陷Welding defect 凹坑Pit未焊透Incomplete penetration 烧穿Burn through未熔合Incomplete fusion 未满焊Incomplete filled groove渣Slag 清根Back chipping夹渣Slag (slag inclusion) 清渣Slag removal夹杂物Inclusion 焊接烟尘Weld fume气孔Blow hole 电光性眼炎Eye-flash焊接性Weldability 横裂纹Transverse crack碳当量Carbon equivalent 纵裂纹Longitudinal crack未焊满Incomplete filled groove 焊趾裂纹Toe crack焊接裂纹Weld crack 机械性能试验Mechanical property test热裂纹Hot crack 试板Test piece冷裂纹Cold crack 试样Specimen氢致裂纹Hydrogen –induced crack 侧弯Side bend延迟裂纹Delayed crack 弯曲Bending层状撕裂Lemellar tearing 横向拉伸Transverse tensile弧坑裂纹Crater crack 宏观试样Macro-etching specimen根部裂纹Root crack 微观试样Micro-examination specimen再热裂纹Reheat crack 破断试验Fracture test热影响区裂纹Heat-effected zone crack 抗裂试验Cracking test晶间裂纹Intercystalline crack 脆性断裂Brittle fracture塑性断裂Plastic fracture 焊接方法Welding process焊接残余裂纹Welding residual stress 焊接工艺Welding technology消除应力Stress relieving 焊接操作Welding operation焊接变形Welding deformation 焊接顺序Welding sequence角变形Angular distortion 焊接方向Direction of welding外观检查Visual examination 常用缩语无损探伤Non-destruction testing(N.D.T.)气电立焊EGW超声波探伤Ultrasonic inspection 药芯电弧焊FCAW射线探伤（X 光）Radiographic inspection(X-rayinspection)实心电弧焊GMAW磁粉探险伤Magnetic particle inspection焊剂铜衬垫单面埋弧自动焊FCB渗透探伤Penetrate inspection 手工电弧焊SMAW熔池Weld-pool 埋弧自动焊SAW焊机（焊接电源）Weld source钨极惰性气体保护电弧焊TIG 机舱部分ENGINE ROOM PART熔化极惰性气体保护焊MIG 一、机舱设备Machines and equipment in engine room 活性气体保护焊MAG 1、主机Main engine手工电弧切割SMAC 1）主机油底壳The sump tank of M.E.2）主机飞轮Fly wheel of M.E3）活塞Piston2、发电机Generator engine1）应急发电机Emergency generator engine2）辅机Auxiliary3、锅炉Boiler1）组合锅炉The composite boiler2）锅炉安全阀The safety valve of boiler3）燃烧器Oil burner unit 3）主空气瓶Main air reservoir4）水位表Water level gauge 4）应急空气瓶Emergency air reservoir5）水位控制器Water level controller 5、控制空气瓶Control air reservoir6）过量蒸气调节阀Excess steam pressure control valve6、空气干燥器Air dryer4、舵机7、分油机Oil purifier1）舵机间Steering room 1）燃油分油机Fuel oil purifier2）舵机装置Steering-gear 2）柴油分油机Diesel oil purifier3）手操舵装置Trick wheel plant 3）滑油分油机Lubricate oil purifier4）油缸Oil cylinder 4）排渣Sludge discharge5）反馈装置Feedback device 8、制淡装置Fresh water generator6）舵Rudder9、焚烧炉Incinerator舵叶Rudder blade10、油水分离器Oil water separator舵杆Rudder stock11、生活污水处理器Sewage treat plant上舵承Rudder carrier12、大气冷凝器Atmosphere condenser热水井Cascade and inspection(hotwell)5）主机燃油供给泵Main engine fuel oil supply pump滑油自清滤器The automatic back-flashlubricating oil filter6）主机燃油增压泵Main engine fuel oil booster pump燃油单元Fuel oil unit 7）主机十字头泵Main engine cross head pump1）主机燃油单元Fuel oil unit of M.E 8）付机海水泵Generator engine sea water pump2）付机燃油单元Fuel oil unit of A.E 9）付机缸套水泵Generator engine cylinder cooling water pump3）粘度计Viscosity controller 10）锅炉给水泵Feed water pump of boiler泵Pump 11）锅炉燃油泵Fuel oil pump of boiler1）主机滑油泵Main engine lubricating oil pump12）分油机供给泵Fuel oil supply pump of purifier2）主机缸套水泵Main engine cylinder cooling water pump13）制淡海水泵Sea water pump of fresh water generator3）主机缸套水预热泵Main engine cylinder cooling water preheating pump14）压载泵Ballast pump4）主机海水泵Main engine sea water pump 15）舱底消防泵Bilge and fire pump17）油渣泵Sludge oil pump 2、柴油澄清舱Diesel oil setting tank18）柴油输送泵Diesel oil transport pump 3、燃油日用柜Fuel oil daily tank19）燃油油输送泵Fuel oil transport pump 4、燃油澄清舱Fuel oil setting tank20）汽缸油输送泵Cylinder oil transport pump 5、滑油澄清舱Lubricating oil setting tank 21）淡水输送泵Fresh water transport pump 6、滑油储藏舱Lubricating oil store tank 22）热水循环泵Hot water circulating pump 7、滑油循环舱Lubricating oil circulating tank 23）饮水日用泵Drinking water pump 8、燃油溢油舱Fuel oil overflow tank舱底消防总用泵Bilge, fire and G.S pump 9、燃油油渣舱Fuel oil sludge tank喷淋泵Sprinkling pump 10 燃油深舱Fuel oil deep tank停泊海水泵Harbor sea water pump 11 滑油污油舱Lubricating dirty oil tank12 滑油溢油舱Lubricating oil overflow tank二、各种舱（箱）柜All kinds of tank 13 滑油油渣打舱Lubricating oil sludge tank1、柴油日用柜Diesel oil daily tank 14 主机淡水膨胀水箱M.E fresh water expansion tank15 付机淡水膨胀水箱A.E fresh water expansion tank16、淡水压力柜Fresh water pressure tank 1、滑油系统Lubricating oil piping system17、热水压力柜Hot water pressure tank 2、燃油系统Fuel oil piping system18、饮水压力柜Drinking water pressure tank3、海水系统Sea water piping system19、淡水舱Fresh water tank 4、缸套水系统Cylinder cooling water piping system20、饮水舱Drinking water tank 5、启动空气系统Start air piping system21、锅炉水舱Boiler water tank 6、控制空气系统Control air piping system22、分油机工作水箱Purify operating water tank 7、排气系统Exhaust piping system23、汽缸油日用柜Cylinder oil daily tank 8、日用供水系统Daily water piping system24、尾管滑油重力柜Gravity tank of tube oil 9、蒸汽系统Steam piping system25、排气水封箱Exhaust seal water tank 10 、锅炉给水和凝水系统Feed water and condensate of boiler piping system26、蒸馏水水舱Distilling water tank 11、燃油净油系统Fuel oil purified piping system27、污水井Bilge well 12、燃油输送系统Fuel oil transport piping system三、各种管系系统All kinds of pipes舵销Rudder pintle 13、滑油净油系统Lubricating oil purified piping system舵杆衬套rudder stock liner 14、滑油输送系统Lubricating oil transport piping system舵杆轴套Sleeve for rudder stock 15、舱底压载系统Ballast and bilge water piping system 舵销承衬套Bush for rudder pintle 四、仪表类Instructions舵销轴套Sleeve for rudder pintle 1、压力表Pressure gauge上舵承底座Rudder carrier seat 2、真空表Vacuum gauge舵销承座Pintle bearing 3、温度计Thermometer舵杆承座Rudder stock bearing 4、吨位表DWT gauge挡圈Retaining ring 5、遥测表Distant survey gauge舵柄Tiller 6、液全器Level switch7）舵角The angle of rudder5、空压机Air compressor1）主空压机Emergency air compressor2）应急空压机7、传感器Sensor 12、机控室Engine control room五、其它Others 13、台虎钳Vise (=vice)1、风机Fan 14、表铜截止阀Bronze close valve2、防海生物装置Anti-foul STM plant 15、表铜截止止回阀Bronze check valve3、泡沫柜Air foam tank 16、铸铁截止阀Cast iron stop valve4、中间轴Middle shaft 17、铸铁截止止回阀Cast iron check and stop valve5、尾轴Propeller shaft 18、调节阀Adjustable valve6、螺旋桨Propeller 19、溢流阀、安全阀Relief valve7、中间轴承Line shaft bearing 20、减压阀Reducing valve8、泡沫灭火机Foam fire extinguisher 六、材料Material9、饮水消毒装置Sterilizer plant 1、管子Pipe10、主配电板Main switch board 2、无缝钢管Seamless steel pipe (tube)11、机舱集控台Engine room control console 3、紫铜管Purple copper pipe4、铁法兰Iron flange 18、支架（马脚）Clamp5、铜法兰Copper flange 19、油漆Paint6、盲板法兰Blind-flange 20、备件Spare parts7、螺丝（螺栓）Bolt8、双头螺丝Stud 七、生产工具Produce tool9、螺帽（螺母）Nut 1、图纸Drawing10、不锈钢螺丝Stainless steel bolt 2、活络钣Adjustable spanner11、垫片（床）Gasket 3、令司板（梅花钣）Ring spanner12、橡皮床Gum gasket 4、开口钣Open –ender spanner13、纸箔床Paper copper gasket 5、管子钳Pipe wrench14、紫铜床Purple copper gasket 6、凿子Chisel15、石墨床Black lead gasket 7、锒头Hammer16、青铅床Black lead gasket 8、锉刀File17、佛纳Feeler gauge 9、螺丝刀Screwdriver10、油漆滚筒Paint roller 4、首先请检查安装说明和电气绝缘11、油漆刷子Paint brush Please check the condition of installation and insulationfirst12、钢锯Hacksaw 5、我们准备将油水分离器动转13、套筒扳手Socket spanner Now we will run the oily-water separator14、手电筒Torch 6、请检查动转情况15、钻头driller Please check the running condition八、英语会话7、接着我们一个一个地做报警/安全保护装置的功能试验1、早上好good morning Now we will do the function test about alarm and safetydevice2、今天我们准备交验油水分离器8、设备交接基本结束Today we will test the oily-water separator. Now the test is over3、请跟我来9、请部有何修改意见？Please fellow me. Do you have any question ?10、非常感谢17、这里增加一只落水斗Thanks Add a drain plug here11、再见18、请用空气压缩空气吹干Good bye Please dry it by the compressed air12、请把这对法兰撬紧松开19、我将回车间支拿肥皂水Please tighten/release the flange I will com to my workshop to take some soap water13、这路管子是从发电机单元来的20、这个系统非常重要的，一定要认真检查The piping is from to the G/E unit This system is very important ,please check it carefully14、这对法兰/接头在漏21、请交验收整改意见This flange /connection is linking Please check your remarks15、这路系统的试验压力是7 公斤22、天太热了，请休息一会The test pressure of the piping system is 7 bar It’s too hot ,please take a rest16、这里请加强please make a clamp here 23、我负责这项工作I am in charge of this job电气部分ELECTRIC PART一、常用词汇Words and expression 模拟Analog(ue)2182 千赫值班接收机2182KHz watch receiver 锚灯Anchor lightA 异常Abnormal 风速风向仪Anemorumbometer应答Acknowledge 阳极Anode有功功率Active power 天线Antenna执行器Actuator 天线馈线连接器Antenna feeder connector调整Adjust 天线引入绝缘端子Antenna leading –in insulator空气断路器Air circuit breaker 天线共用器Antenna multicoupler报警系统Alarm system 天线调谐器Antenna tuner交流电Alternating current 电焊机Arc welder电流表ammeter 声音的Audible放大器Amplifier 自动海图标绘仪Auto chart plotter自动舵Auto pilot自动的Automatic自动雷达标绘仪Automatic radar plotting aid球鼻首警告灯Bulbous bow warning light自动电话Automatic telephone 汇流排Bus(-)bar电压自动调节器Automatic voltage regulator 汇流排Bus –tie –in自动化系统Automation system 蜂鸣器Buzzer压载控制台Ballast control console C、电缆Cable镇流器Ballast 电缆填料函Cable gland底座Base 敷设电缆Cable laying电池Battery 电缆管Cable pipe (conduit)铃Bell 电缆扎带Cable strap弯曲Bend 电缆托架Cable tray床头灯Berth light 校准器Calibrator失电Black out 电容capacitor刹车Brake 阴板Cathode电刷Brush 警告牌Caution plate顶灯Ceiling light 通讯Communication中央处理器Central processing unit 计算机Computer通道Channel 接头Connector充电器Charger 恒电流Constant current充放电板Charging&discharging board 消耗Consumption海图灯Chart table light 触头Contact检查Check 接触器Contactor芯片Chip 控制箱Control box清洁Clean 控制箱Controller雨雪清除器Clear view screen 芯线Core二氧化碳释放报警CO2 release alarm 角灯Corner light同轴电缆Coaxial cable 计算器Counter线圈Coil 电流Current冷库呼叫Cold store calling D、损坏Damage危险气体报警箱Dangerous gas detecting&alarm box双极单刀开关Double pole single way switch白昼信号灯Daylight signal light 双极双刀开关Double pole two way switch 去耦Decoupling set 天线收发转换开关Duplexer台灯Desk light 值班水手呼叫Duty sailor calling控测器Detector 接地Earth拨号Dial 接地排Earth bar数字选择呼叫收信机Digital select –call receiver测深仪Echo sounder调光器dimmer 电工试验板Electric test panel直流电Direct current 电机员Electrical engineer直接起动Direct –on –line starting 电极Electrode磁盘Disk 应急照明分电箱Emergence lighting distribution box显示Display 应急示位标Emergence position indicating radiobeacon遇险信息控制器Distress message controller 应急停Emergence stop多普勒记程仪Doppler speed log应急配电板Emergency switch board 馈电品Feeder panel机舱报警Engine alarm 滤波器Filter集控台Engine control console 火警复显器Fire alarm repeater机舱监测报警Engine room monitoring&alarm system防火风闸控制单元Fire damper control unit轮机员呼叫Engineer calling panel 火警检测箱Fire detecting box轮机员安全Engineer safety system 火焰探头Flame detector增强群呼叫收讯机Enhance group call receiver 闪光灯Flash light交换机Exchanger 浮充电Float charge防爆灯Explosion proof light 强光灯Flood light延伸报警板Extension alarm panel 流程图Flow chart故障Failure 流量开关Flow switch故障Fault 荧光灯Fluorescent light反馈Feed back 雾笛Fog horn频率Frequency熔丝Fuse 感温探头Heat detector填料Gasket 底座Holder通用报警General alarm 电笛、喇叭Horn发电机Generator 病房呼叫Hospital calling发电机屏Generator panel 照明Illumination（铜）锣、钟Gong 白炽灯Incandescent light全球卫星定位导航GPS navigator 指示器Indicator组合灯板Group alarm light pillar 卫星B 站INMARSAT B station组合起动屏Group starter panel 卫星C 站INMARSAT C station电罗经Gyro compass 输入输出Input /output卤素灯Halogen light 安装Install听筒Handset 仪表Instrument硬件Hardware 绝缘胶带Insulating tape航向Heading 绝缘Insulation接口、界面Interface 限位开关Limit switch连锁Interlock 连接Link中断Interrupt 负载Load逆变器Inverter 劳莱收信机Loran receiver接线盒Junction box 磁罗经Magnetic compass键盘Keyboard 主机电子调速器Main engine electronic governor灯泡Lamp 主机功率、纽力仪Main engine power& torque unit液位开关Level switch 主机遥控系统Main engine remote control system液位传感器Level transmitter 主机转速表Main engine revolution meter灯Light 主机安全系统Main engine safety system灯柱Light column 主机增压器转速表Main engine turbo-charger speed meter 照明分电箱Light distribution box 主配电板Main switchboard避雷针Lighting arrester 手动手册Manual标记Mark 移动Move桅杆Mast light 万用表Multimeter母子钟Master& slave clock 铭牌Name plate匹配箱Matching box 窄频直接打印机Narrow-band direct printer测量Measure 航行灯Navigation light兆欧表Megohmmeter 导航系统Navigation system仪表Meter 航行监控台Navigation watch console话筒Microphone 航行警告收信机NA VTEX receiver镜向灯Mirror light 负极Negative监视器Monitor 网络Network莫斯键Morse key 标称值Nominal value电动机Motor 常闭Normally closed塑壳断路器Moulded case circuitbreaker常开Normally open鼠标Mouse 失控灯Not under-command light欧姆表Ohm gauge 正极Positive欧姆收信机Omega receiver 功率、电源Power车钟记录仪Order printer 电力分电箱Power distribution box示波器Oscilloscope 功率因素Power factor过电流Over current 优先卸载Preferential trip过载Overload 压力开关Pressure switch巴拿马动河操舵灯Panama canal steering light 压力传感器Pressure switch 并联、并车Parallel 一次系统Primary system相Phase 打印机Printer光敏电阻Photo resister 程序Program测速传感器Pick up 螺旋桨警告灯Propeller warning light插头Plug 广播Public addressor左舷灯Port light 脉冲Pulse便携电话Portable telephone 按钮Push button雷达Radar 电阻Resistance雷达应答器Radar transponder 逆功率Reverse power收音机Radio 旋转灯Rotating light无线电测向仪Radio direction finder 舵角指示器Rudder angle indicator随机存取存储器Radio system 运转灯Running lamp额定Random access memory 屏幕、屏蔽Screen无功电流Rated power 螺丝刀Screwdriver插座Receptacle 搜索灯Search light录音机、记录仪Recorder 二次系统Secondary system整流器Rectifier 串联Series继电器Relay 屏蔽Shield复位Reset 船名灯Ship name light岸电箱Shore connection box短路Short circuit展示、给-----看Show 电磁阀Solenoid valve分励脱扣Shunt trip 消音Sound off停车Shut down 声力电话Sound power telephone签字Sign 空间加热器Space heater信号集合箱Signal acquisition unit 扳手Spanner信号灯Signal light 喇叭Speaker单边带收发机Single side band transceiver分配器Distributor电笛Siren 右舷灯Starboard light慢车Slow down 起动Start烟气探测报警箱Smoke detecting &alarm box 起动带Start感烟探头Smoke detector 尾灯Stern light插座Socket 停止Stop软件Software 苏伊士运河尾灯Suez canal stern light电烙铁Soldering iron 支撑物supporter开关Switch 验电笔Test pen打开Switch on 试验程序Test procedure关闭Switch off 热敏电阻Thermistor同步屏Synchronizing panel 热电偶Thermocouple同步表Synchronoscope 温度计Thermometer转速表Tachometer 恒温计Thermostat录音机Tape recorder 触摸屏Touch panel车钟Telegraph 轨迹球Trackball电视Television 收发机Transceiver温度开关Temperature switch 传感器Transmitter温度传感器Temperature transmitter 变压器Transformer接线柱Terminal 脱扣Trip接线排Terminal board 欠电压Under voltage试验Test 不中断电源Uninterrupted power source卸载Unload 二、会话Dialog and conversation超高频VHF telephone 船东o- owner视觉的Visual 验船师s-survey电压V oltage 检验员q-quality inspector电压表Voltmeter 电工e-electrician壁灯Wall light 1、检验电缆敷设瓦特Watt Inspection cable laying波道Waveguide 你能带我去看机舱电缆敷设气象传真收信机Weather fax receiver Q: could you show me cable laying of engine room?驾控台Wheel speed &directionindicator好，走吧。
船舶专业英语词汇
ABS (American Bureau of Standard)美国船级社ANG (Angle Bar)角钢BFE (Builder Furnish Equipment)建造商提供设备BG (Bulk Carrier)散货船BHD (Bulkhead)舱壁BHP (Break Horsepower)制动马力BL (Base Line)基线BM (Breadth Molded)型宽BV (Bureau Veritas)法国船级社CAD (Computer Aided Design)计算机辅助设计CAM (Computer Aided Manufacturing)计算机辅助制造CB (Center of Buoyancy)浮心CCS (China Classification Society)中国船级社CF (Center of Floatation)漂心CFE (Contractor Furnish Equipment)承包商提供设备CG (Center of Gravity)重心CH (Channel)槽钢CM (Metacenter)稳心CPP (The Controllable Pitch Propeller)可调螺距桨CS (Carbon Steel)碳素钢DB (Double Bottom)双层底DK (Deck)甲板DM (Depth Molded)型深DNV (Det Norske Veritas)挪威船级社DWG (Drawing)图DWL (Design Waterline)设计水线DWT (Deadweight)载重量FAT (Factory Acceptance Test)工厂验收试验FB (Flat Bar)扁钢FEM (Finite Element Method)有限元法FPSO (Floating Production Storage Offloading) 浮（船）式生产储油卸油系统FSO (Floating Storage Offloading)浮（船）式储油卸油系统Fwd (Forward)向船艏GL (Germanischer Lloyd)德国船级社GM (Metacentric Height)初稳心高HP (Half Bulb Plate)球扁钢LBP (Length between Perpendiculars)垂线间长LCG (Longitudinal Center of Gravity)纵向重心LNG (Liquefied Natural Gas Vessel) 液化石油气船LOA (Overall Length)总长Long. (Longitudinal)纵骨LPG (Liquefied Petroleum Gas Vessel) 液化天然气船LR (Lloyd's Register)英国劳氏船级社MDK (Main Deck)主甲板MODU (Mobile Offshore Drilling Units)移动式近海钻井平台MS (Mild Steel)低碳钢MTO (Material Takeoff)材料估算NK (Nippon Kaiji Kyokai)日本海事协会OFE (Owner Furnished Equipment)船东提供设备OT (Oil Tight)油密PL (Plate)板RI (Register Italian)意大利船级社SB (Starboard)右舷Semi- (Semi-submersible Platform)半潜式钻井平台STLP (Suspended Tension Leg Platform)悬式张力腿平台TCG (Transverse Center of Gravity)横向重心TEU (Twenty-foot equivalent Unit)20英尺国际标准集装箱TLP (Tension Leg Platform)张力腿平台UCLL (Ultra Large Crude Carrier)超大型油船VCG (Vertical Center of Gravity)垂向重心VLCC (Very Large Crude Carrier)特大型油船WB (Web Bar)腹板WL (Waterline)水线WT (Water Tight)水密MECHANICAL & PIPING（轮机）：AHU (Air Handling Unit)通风装置BHP (Break Horsepower)制动马力A/C (Air Compressor)空气压缩机A/C (Air Conditioning)空调BB (Ball Bearing)滚珠轴承BRG (Bearing)轴承CAS NUT(Castle Nut)蝶型螺帽CCR (Central Control Room)中心控制室COW (Crude Oil Washing)原油洗舱DFO (Diesel Fuel Oil)柴油DPS (Dynamic Position System)动力定位系统DT (Double-Thread)双头螺纹FS (Forged Steel)锻钢FW (Fresh Water)淡水FO (Fuel Oil)燃油GRP (Glass-reinforced Plastic)玻璃钢HVAV (Heating Ventilation and Air-condition)暖通空调系统HPU (Hydraulic Power Unit)液压工作站LSA (Life Saving Apparatus)救生器具LCC (Local Control Console)机旁控制台LO (Lube Oil)滑油MDO (Marine Diesel Oil)船用柴油OS (Operation System)操作系统PLC (Programmable Logic Controller)逻辑控制单元PMS (Power Manage System)动力管理系统ELECTRICAL（电气）:AC (Alternative Current)交流电AVR (Automatic Voltage Regulation)自动电压调整计CCTV (Closed Circuit Television)闭路电视CMS (Cargo Monitoring System)货物监控系统DC (Direct Current)直流电DFT (Dry Film Thickness)干膜DG (Diesel Generator)柴油发电机DVD (Digital Video Disc) 数字化视频光盘EMSP (Emergency Shutter Panel)应急关断板ESS (Emergence Shutdown System)应急关闭系统GPS (Global Position System)全球定位系统HG (Harbor Generator)停泊发电机HT (High Temperature)高温JB (Junction Box)接线盒LED (Light Emitting Diode)发光二极管LT (Low Temperature)低温MCU (Main Control Unit)主控器箱MG (Main Generator)主发电机MUR (Manual Voltage Regulation)手动调压器NEMA (National Electrical Manufacturers Association)国际电气制造业协会PA (Public Address System)公共寻呼系统PWM (Pulse Width Modulation)脉宽调制ST (Starter)启动器SWBD (Switch Board)配电盘，配电板UPS (Uninterrupted Power Supply)不间断电源VCR (Video Cassette Recorder)录像机PAINTING（涂装）:ARD (Alkyd Resin Deck)醇酸树脂甲板漆ARF (Alkyd Resin Finish)醇酸树脂面漆ARP (Alkyd Resin Primer)醇酸树脂底漆A/C (Anti-corrosive Paint)防腐漆CAF (Compressed Asbestos Fiber)压缩石棉填料EDP (Epoxy Deck Paint)环氧甲板漆EFP (Epoxy Finish Paint)环氧面漆EPP (Epoxy Primer Paint)环氧底漆ETPF (Epoxy Tank Paint Finish)环氧舱室面漆ETPP (Epoxy Tank Paint Primer)环氧舱室底漆ETP (Epoxy Topside Paint)环氧干舷漆ERL (Erosion Resistant Lacquer)防腐漆ECP (Etching Primer) 磷化底漆EPR (Ethylene-Propylene Rubber)乙丙橡胶F/C (Finish Coating)面漆IZP (Inorganic Zinc Primer)无机锌底漆IZSP (Inorganic Zinc Shop Primer)无机锌车间底漆UTP (Polyurethane Topside Primer)聚氨脂干舷漆TE (Tar Epoxy Paint)环氧焦油漆VTP (Vinyl Tar Primer)聚乙烯焦油底漆ZRP (Zinc Rich Primer)富锌底漆WELDING and Material（焊接与材料）ASTM (American Society for Testing Materials)美国材料实验协会AWS (American Welding Society)美国焊接协会FCAW (Flux Cored Arc Welding)药芯焊丝电弧焊FRP (Fiberglass Reinforced Polyester)玻璃钢GMAW (Gas Metal Arc Welding)气体保护金属极电弧焊GRP (Glass Reinforced Polyester)玻璃钢GTAW (Gas Tungsten Arc Welding)气体保护钨极电弧焊GW (Gravity Welding)重力焊MPI (Magnetic Particle Inspection) 磁粒检验NDE (Nondestructive Evaluation)无损鉴定NDT (Nondestructive Testing)非破坏性检验PVC (Poly Vinyl Chloride)聚氯乙烯S/W (Spot Weld) 点焊SAW (Submerge Arc Welding)埋弧焊SMAW (Shielded Metal Arc Welding)手弧焊UT (Ultrasonic Test)超声波检验WPS (Welding Procedure Sheet)焊接程序表WQT (Welding Qualification Test)焊工资格检验OTHERS（其它）AE (Assistant Engineer)助理工程师ANSI (American National Standards Institute)美国国家标准局API (American Petroleum Institute)美国石油协会ASME (American Society of Mechanical Engineers)美国机械工程师协会Bbls (Barrels) 桶（美制容量单位1桶= 159升），C.E. (Chief Engineer) 总工程师CEO (Chief Executive Officer)首席执行总裁CIS (Chinese Industrial Standard)中国工业标准CNOOC (China National Offshore Oil Company)中国海洋石油总公司Co Ltd.(Company Limited)（股份）有限公司cu.ft. (Cubic Feet) 立方英尺cu.in. (Cubic Inch) 立方英寸GB (Guo Biao)国标GM (General Manage)总经理H.Q. (Headquarters) 总部HSE (Health, Safety & Environment)健康，安全和环保ID (Inner Dimension)内径IEC (International Electro technical Commission)国际电工协会IMO (Intergovernmental Marine Organization)国际海事组织ISO (International Standardization Organization)国际标准化协会ITU (International Telecommunication Union)国际电信联盟Ksi (kilopounds per square inch)千磅/平方英寸N/A (None Applicable)不适用NACE (National Association of Corrosion Engineer)全国防蚀工程师协会NFPA (National Fire Protection Association)国家防火协会OD (outer Dimension)外径QA (Quality Assurance)质量保证QC (Quality Control)质量管理（检查）ST (Short Ton)短吨SOLAS (International Convention of the Safety of Life at Sea)国际海上人命安全公约Spec. (specification)说明书，规格书sq.ft. (Square Feet) 平方英尺sq.in. (Square Inch) 平方英寸PROPER NOUN（专有名词）:Basic Design(基础设计): Preparation of specification and plans/drawings outlining the design and in sufficient detail to gain Class approval.总括性的设计规格书和图纸等，其详细程度仅足可以通过船级社认可其设计思想。
船舶常用英语(一)
salvage ship救捞船
dredger挖泥船
trailing suction dredge耙吸挖泥船
cutter suction dredger绞吸挖泥船
bucket wheel dredger斗轮挖泥船
bucket dredger链斗挖泥船
reclamation craft吹泥船
screw ship; propeller vessel螺旋桨船
airscrew ship; aerial propeller vessel空气螺旋桨船
hovercraft; aircushion craft气垫船
hydrofoil水翼船
hydrojet propelled boat, water jet boat喷水船
grab dredger抓斗挖泥船
dipper dredger铲斗挖泥船
floating pitter; drive pitter打桩船
floating crane; derrick boat起重船
floating dock浮船坞
cable layer; cable ship布缆船
scientific surveying ship科学考察船
after peak bulkhead艉尖舱舱壁
after peak tank艉尖舱
air hole空气孔
air pipe空气管
appendage（船体水线下的）附体；附件
auxiliary machinery辅助机械；辅机
balanced rudder平衡舵
ballast压载（物）
ballast line压载水管系
tourist ship; passenger carrier旅游船
船舶常用英语词汇
船舶英语常用词汇1. abrasive blasting (磨料)喷砂法, 喷砂2. access n.通路, 访问, 入门；vt.存取, 接近3. acknowledge vt. 承认, 答谢, 报偿4. alignment n.排列成行;排列成的行列;结盟；合作（亦作：alinement）；n.队列, 结盟5. annex n. 附件vt. 并吞, 附加6. anti slip n.防滑7. application n.请求, 申请, 申请表, 应用, 运用, 施用, 敷用;应用,应用程序,应用软件8. argument n.争论,辩论,论据,论点,～(for,against),意见9. assembly装配，安装，组装组装件，总成机组，集合,装配,集会,集结,汇编【机】装配;装配车间; 部件, 组(合)件; 成套件; 联合装置10. attachment strap 搭接带, 搭接板11. available adj.可用到的, 可利用的, 有用的, 有空的, 接受探访的12. back strap 背垫条, 衬垫, 垫里, 垫座13. bar 杆,棒,棒材,钢筋,型材,型钢;炉条,(锚链的)横档,闩;【电气】汇流排;柜台,酒吧,快餐柜台;阻拦,禁止 aitch bar工字(形)钢,宽缘工字材 anchor bar 撬锚棒 angle bar 角材,角钢 back(ing) bar 【焊接】垫板,背垫短角材 batten(ing) 舱口压条 bearer bar 托梁,支承梁 bearing (steel) bar 支承钢筋,受力(钢)筋;承重杆,承压条 bolt bar 插销,驻栓;螺柱杆 bounding bar 缘周角材 brass bar 黄铜棒 bulb bar 球缘材,球缘钢 bulb flat bar 球扁钢 bulb-angle bar 球缘角材,球缘角钢 bulb-tee bar 丁字形球缘材,丁字形球缘钢 bulb bus bar 【电气】汇流条,汇流排,母线 channel bar 槽材,槽钢 copper bar 紫铜棒 crow bar 起货钩;橇杆,撬棒 deep (frame) bar 强肋骨 equal-angle bar 等边角材,等边角钢 face bar 面材,缘边角材 fender bar 护舷材(小艇的),护舷木 filler bar 焊条 flat bar 扁材 forged stem bar 锻造首柱 frame bar 肋骨角材,肋骨钢 guard bar 栏杆,扶手,扶栏 H bar 宽缘工字钢,工字钢 half-round bar 半圆钢,半圆材 I bar (窄缘)工字钢 iron bar 扁材,铁条,钢条 L bar 不等边角钢,不等边角材 mo(u)d bar 型材,型棒 pinch bar 撬杆,撬棍,绞盘棒 plain bar 普通角材,平角钢 plain bulb bar 球缘扁材,球扁钢 rack bar 齿条,齿杆 reinforcing bar 钢筋,加强筋 round bar 圆材,圆钢 sectional bar 型材,型钢 square bar 方材,方钢 stop bar 止动条T bar “T”形材,“T”形钢 tooth(ed) bar 齿条,齿杆,齿闩 unequal angle bar不等边角钢,不等边角材 unequal flange[unequal leg] bar 不等边角钢,不等边角材14. barge 驳船，大平底船 covered barge 甲板驳 deck barge甲板驳 derrick barge 浮吊，起重驳 dump barge 非自航驳 flat top barge 平甲板驳 flat bottomed barge 平底驳15. banister n. 栏杆的支柱, 楼梯的扶栏16. batten 样条，万能曲线尺；用板条钉住 batten down 封舱 mrasureing batten 标尺17. bay 舱壁间距，强肋骨间距；集装箱货位，货柜存放器；停泊地，码头区 assembly bay 装配工段 building bay 建造工段 fitting bay 舾装工段 welding bay 焊接工段18. beam n.梁, 桁条, (光线的)束, 柱, 电波, 横梁v.播送19. bearing pad乌金轴瓦, 轴承垫20. bending shackle 锚卸扣21. bevel n.坡口,斜角, 斜角规, 倾斜, 斜面vi.成斜角,开坡口,做成斜边vt.使成斜角 beveling(of the edge) 开坡口,各种形状坡口的加工22. blade 推进器叶片(舢板)桨叶舵板翼叶片刀口n.轮叶,叶片23. blasting n.爆破(作业);鼓风; 吹净;喷丸处理; 喷砂处理24. boltn.门闩, 螺钉, 闪电, 跑掉v.上门闩, 囫囵吞下, 逃跑25. boss(铸锻件表面)凸起部毂，轴毂，轮毂，轴套。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
常用船舶词汇
船舶常用名词主尺度
Principal
dimension
<td width="36" rowspan="44" valign="top"
style="width:27.0pt;border-top:none;
border-left:none;border-bottom:solid windowtext 1.0pt;border-right:solid windowtext 1.0pt; padding:0cm 5.4pt 0cm 5.4pt">
船籍港
port of registry 总长Length over all
港口,左舷
port 垂线间长
Length between perpendicular
船坞,码头
dock 型宽
Breadth moulded
挖泥船
dredge, dredger 型深Depth to maindeck
驳船
Barge,lighter 设计满载水线draft
水翼船
hydrofoil 全船肋距Frame spacing
双体船catamarans 梁拱camber
货船
cargo
freighter 主机型号
Engine type
潜水艇
submarine 主机额定功率/转速
Engine power/v.
velocity
渡船,渡轮
ferry,
ferryboat 舵机舱Steering room
客船
passenger
boat 艉尖舱After peak tank 油轮
tanker 集控箱
Control room
救生艇
lifeboat 污油舱Oil sludge tank.
气垫船
hovercraft 滑油舱Lub oil T.K.
压舱物
ballast 燃油舱
Heavy oil T.K.
客舱
berth, cabin, stateroom 货油舱
Cargo oil T.K.
船腹,船底污水
bilge 压载舱
Ballast water
舷墙
bulwark 隔离空舱Insulate room
上甲板
upper deck 应急消防泵舱
Emergency fire
room
内龙骨
keelson 艏
bow
龙骨
keel 艏压载舱Bow ballast water 船尾
stern 锚
anchor
船桥
bridge 艏尖舱forepeak
舷窗
bull's eye, porthole 艉楼甲板
Poop deck
起锚机
capstan 艇甲板
Boat deck
球鼻艏
Bulbous bow 驾驶甲板NAV. deck
肋骨
Frame, rib 罗经甲板Compass deck
舱口,升降口hatchway 艏楼甲板Forecastle deck
锚链孔hawsehole,
hawse 驾驶室Wheel house 舵
helm 艉柱sternpost
舵杆
tiller船舶经纪人ship broker
船身
hull 吨位tonnage
信号灯lantern 左舷larboard
船中部
midship 右舷starboard
桨架
oarlock, rowlock 侧倾list
最下层甲板
orlop 桨
oar
船尾
poop, stern 海里mile
肋骨
rib 下水
launch, launching
航海日志
logbook 舷
Port, shipboard
推进器,螺旋桨
screw, propeller 货舱
hold
小舱口
scuttle 吊车,提物机
windlass,
winch
储藏室
storeroom 水线,吃水线waterline
船舷上缘
gunwale,
gunnel 肋板
FLPL(floor plate) 纵骨Longitudinal(long)。