模具零件名称对照表
常用模具零件中英文对照表
常用模具零件中英文对照表2005-12-19 14:51:17中国注塑网一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口：pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边：guide pin顶针板：ejector retainner plate托板：support plate螺丝：screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller 扣机〔尼龙拉勾〕：nylon latch lock斜顶：lifter模胚〔架〕：mold base上内模：cavity insert下内模：core insert行位〔滑块〕：slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞:pipeplug锁模块：lockplate斜顶：anglefrompin斜顶杆：angleejectorrod尼龙拉勾：partinglocks活动臂：leverarm复位键、提前回杆：earlyreturnbar气阀：valves斜导边：anglepin术语：terms承压平面平衡：partingsurfacesupportbalance模排气：partinglineventing回针碰料位：returnpinandcavityinterference模总高超出啤机规格：moldbaseshuthight顶针碰运水：waterlineinterfereswithejectorpin料位出上/下模：partfromcavith(core)side模胚原身出料位：cavitydirectcutonA-plate,coredirectcutonB-plate.不准用镶件：Donotuse(core/cavity)insert用铍铜做镶件：useberylliumcopperinsert初步〔正式〕模图设计：preliinary(final)molddesign反呵：reversecore弹弓压缩量：springcompressedlength稳定性好：goodstability,stable强度不够：insufficientrigidity均匀冷却：evencooling扣模：sticking热膨胀：theroexpansion公差：tolorance铜公(电极〕：copperelectrode塑件模具相关英文词汇出处：FanE『翻译中国』(转载) FanE『翻译中国』2005-12-16 20:41:59compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具encapsulation molding低压封装成型、射出成型用模具two plate两极式〔模具〕well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针零件英语punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location 定位支承块 air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block 滑块sliding dowel block 滑块固定块active plate 活动板lower sliding plate 下滑块板upper holder block 上压块upper mid plate 上中间板spring box 弹簧箱spring-box eject-rod 弹簧箱顶杆spring-box eject-plate 弹簧箱顶板bushing bolck 衬套cover plate 盖板guide pad 导料块14. electrical discharge machining (EDM) 电火花加工15. electrical insulating property 电绝缘性能16. electrochemical die-sinking machine 电解型腔加工机，电解型腔加工机床17. electrochemical machine (ECM) 电解加工机床，电化学加工机床18. electrochemical machining (ECM) 电解加工，电化学加工19. electro-discharge cutting 电火花加工，电火花切割20. electro-discharge cutting machine 电火花切割机21. electro-discharge machine tool 电火花加工机床22. Electro-discharge Machine 电火花加工机床23. electro-discharge machining 电火花加工24. electro-discharge machining process 电火花加工工艺，电火花加工工序25. epoxy resin 环氧树脂9. guide bushing 导套10. guide pillar 导柱，导杆，导柱11. guide pin 导向销，导杆12. guide pin cover 导柱盖13. guide plate 导料板，导板14. guide plate blanking die 导板式冲裁模，导板式落料模15. guide post 导柱，导柱16. guide stock plate 挡料板4. injection mold 注射模，注塑模5. injection molding 注射成型，注塑成型6. injection-molding machine 注塑机，注射机，注塑成形机7. injection plunger 注射柱塞8. in-line reciprocating screw 联机往复螺杆，串联往复螺杆，直线排列往复螺杆9. inner ram 内滑块10. inserting molding 嵌件成形11. integrated manufacturing 集成制造12. internal stress 内应力13. intermediate platen 中间板，隔板塑料成型模具的主要设计要素脱模距stripper distance脱模斜度draft投影面积projected area最大开距maximum daylight;open daylight闭合高度mould-shut height抽芯距core-pulling distance抽芯力core-pulling force脱模力ejector force开模力mould opening force模内压力internal mould pressure;cavity pressure成型压力moulding pressure背压环back-up ring1 bar = 14.5psi高压接头bite type fitting液压马达hydraulic motor冷却水流量计waterflow regulator打磨器材abrasive material打磨砂轮grinding wheels切割砂轮cutting wheels码模夹(注塑机使用) mould clamps; lifting clamps 小五金工具piping tools高压力软管high pressure hose风管,水软管air .water hose高压油表pressure gauge压力油喉hydraulic hoses光塑检测photoelastic testing吹塑模plastic blow mould注塑模plastic injection mould冲扎复合模blank & form compound die精密冲模precision blanking die熔料流动率MFR=melt flow rate熔料流动指数MET=melt flow index推板导柱guide pin for ejector plater座板clamping plate垫块space block(plate)推板ejector block(plate)afdek plate 档尘板guide stripe 行位后板cavity sub-insert 前模镶件core sub-insert 后模镶件sprue puller insert 扣针镶件stage ejector 顶棍spacer rock(risers) 间隔板变形distortion弯曲warp拖花drag marks火花纹EDM marks困气venting烧黑burns外表缩水shrinkage料位过薄/砸穿thin wall stock走水不平行uneven fill pattern夹水纹/流纹witness line;mismatch;stress marks 走水纹knit lines走水不齐short shotsorifice 料口nozzle seat 热嘴垫圈nozzle plate 射嘴板cross pin 十字头销sled 射台seal ring 封密圈spacer rail 介子座heater groove 发热管槽heater cement 发热管的结合剂soak 浸泡seat 垫圈ream 铰大圆孔直径grind 磨床drill 钻床mill 铣床caliper 卡尺G-caliper 分厘卡Depth Gauge 深厚计hardness tester 硬度计angle gauge 角规marble table 云台石projector 投影仪height gauge 高度仪microscope 显微镜plug gauge 塞规leveller 水平器R gauge R 规Inter caliper 内分厘卡surface 平面仪item number 细目编码catalog number 材料分类编码undercut lip 倒扣口hot tip = hot drop = nozzle 热嘴blow-off strip 放气板blow-off nozzle 吹风口spiral hose 螺旋式的连接喉rust solvent 除锈剂shaft 曲轴tensile strength 拉伸力yield strength 屈服力spark erosion 电火花蚀刻etch(photo-etch) 电蚀harden 淬硬copper electrode 铜公corrosion resistance 耐腐蚀anneal 退火heat treatment 淬火FEM(finite elemnet method) 有限元法preliminary tool design 初期模具设计图zone 热流道区域reverse taper 倒啤把clamp plate 码板toggle clamp 快速夹vacuum furnace 真空炉cavity insert rounds 圆柱镶件cavity insert b0locks 方柱镶件tensile strength 抗张强度,抗拉强度Concept drawing 概念图Assembly drawing 装配图mismatch;witness line 夹纹shut-off(n.) 枕位venting valves 疏气阀venting plug 疏气塞valve casing 阀门罩twist drill 旋钻harden/nitride 碎硬anneal 退火temper 回火stess crack 应力断裂corrosion resistance 防腐,防锈tensile strength 物】抗张强度,抗拉强度split mould (别离)组合式的模具inclined plate 斜面inclined bolt 斜栓jaw (工具,机械等)夹住东西的局部,钳口step change of the P/L 分形面枕位的改变thin steel section 较薄的料位clean-up 清理,去除,清扫Mold Dating Insert 模具日志镶件Hot Sprue Bushing 热浇口套semi-automatic 半自动quick disconnector 快速断开接头full shot 足量注射mismatch 夹痕;夹水纹ejector mark 顶痕screw boss 螺丝孔,螺丝基座sink mark 缩坑15% glass filled ABS 掺有15%玻璃的ABS spraying mold release 脱模剂drag mark 拖痕stress mark 应力痕reinforcement rib 加强筋slght stoning 轻度磨砂soliid line 实线dotted line 虚线internal diameter 内径external diameter 外径nickel-plated 电镀的handling hole;lifting hole 吊装孔parallel 平行块piston 活塞plunger 柱塞carrier 导轨rest 支架item number 工程编号catalog item 商品目录编码dimensional datum 尺寸基准heat treatment certification 淬硬证明文件back-up bushing 支撑导套jacking screw 起重螺丝,千斤顶tapped hole (带有螺旋角度的)螺丝孔diagonal corner 成对角的角落burn mark 烧痕hot runner mainfold (热流道板)分流板texuring 蚀纹clamping screw (注塑机)码模螺丝imperial 英制的metric 公制的puller bushing 水口套puller bar 水口铁drool bushing 防漏胶套筒safety switch 限位制water line connected internally or hard tubing 不可用胶喉连接运水lifter on square rod or locked from rotation 用方形柱或用管钉止转gate insert 入水镶件gate shut-offs 流道开关配件guided ejection 中托司parting line shutoff 前后模接触面waterlines clear tie bars. 运水喉咀接驳位要避开啤机呵林柱. BGV=Balanced Gate Value 平衡入水值spacer 垫块pocket 挖槽rough 粗加工finish 精加工plunge rate 进刀率retract rate 提刀速率splindle rate 主轴转速coolant 冷却液SPLIT RING 开口环(钥匙圈)侧向抽芯力side pulling-core forceconvert.transfer 转图guide pin 边针Tee slot cutter T形SLOT CUTTERzigzag 双向切削constant overlap spiral 等距环切parallel spiral 环绕切削parallel spiral clean corners 环切并清角morph spiral 依外形环绕true spiral 螺旋切削one way 单向end mill 平铣刀spher mill 球刀bull mill 圆鼻刀face mill 面铣刀rad mill 圆角成型刀chamfer mill 倒角刀slot mill 槽刀taper mill 推拔铣刀dove mill 鸠尾铣刀lot mill 棒状drill 钻孔reamer 纹刀bore bar 搪刀tap RH 右牙刀Tap LH 左牙刀ctr Drill 中心钻spot drill 点钻cntr bore 沉头孔刀c. sink 鱼眼孔钻loft surface 举升曲面coons surface 昆氏曲面ruled surface 直纹曲面revolved surface 旋转曲面swept surface 扫描曲面draft surface 牵引曲面grinding wheel 磨砂使用的轮子quench steel 将...淬火,使冷却stress relieving 应力消除molten 熔热的oxide film 氧化层guide pin and sleeve, locating ring ,导边,司筒,定位圈ejector ,ejector balde, ejector sleeve,顶针,扁顶针,顶针司筒, lifters, wear plate,horn pin,斜坊,磨损板,气顶针,O ring, water baffle, water pipe plug,O形圈,隔片,运水管道塞, water line connector,wear plate ,运水管道转接头,耐磨板air cylinder,hydraulic cylinder,氯压缸,液压缸micro switch,oil nipple, spring,开关装置,油枪接头,弹弓sprue bushing,early return system,浇口套,早期回撞装置, accelerated ejectors, slied holder,加速顶针,注塑周期计数器, cycle counter,date stamper，滑块固定板,生产日期铭牌,hot runner system ，热流道系统chemical composition 化学成份thermal conductiivity 导热性能thermal diffusivity 热扩散性能dimensonal stablity 尺寸稳定性能cooling effiency 冷却效率easiler ejection 易于脱模alloy insert 合金镶件(cooling) duct 输送管;导管maintenance cost 维护费用ultrasonic testing 超声波检测crack 断裂direct gate 直接浇口ring gate 环形浇口disk gate;disphragm gate 盘形浇口spoke gate;spider gate 轮辐浇口pin-point gate 点浇口edge gate 侧浇口submarine gate;tunnel gate 潜伏浇口fan gate 扇形浇口tab gate 护耳浇口runner plate 流道板(或冷或热)secondary nozzle 二级喷嘴torpedo;torpedo body assembly 鱼雷形组合体catridge heater 管式加热器heat pipe 热管valve gate 阀式浇口force plunger;pot plunger 柱塞flash groove;spew groove 溢料槽impression;cavity block;cavity plate 凹模punch;force 凸模movable insert;loose detail 活动镶件cavity splits;core splits(凹模拼块) (型芯拼块) 拼块side core 侧型芯thread plug;threaded core 螺纹型芯thread ring;threaded cavity 螺纹型环cutting wheel 切割砂轮grinding wheel 打磨砂轮abrasive material 打磨器材mould clamps;lifting clamp 砂模夹(注塑机使用)air (water) hose 风管,水轮管pressure gauge 高压油表hydraulic hose 压力油喉plastic blow mould 吹塑模plastic injection mould 注塑模blandk&form compound die 冲扎复合模precisiion blanking die 精密冲模MFR=melt flow rate 熔料流动率MFT=melt flow index 熔料流动指数handling hole 拉铃孔stop plate 限位块linder bush 衬套spacer block(plate) 垫块,方铁back-up ring 背位环standoff 限位块American Safety Hoist Rings. 英制平安吊装环Mechanical Properties 机械性能Tensile Strength(MPa) 抗拉强度elongation 延伸率hardness(Brinell) 硬度shear stength(MPa) 剪切力impact strength 冲韧性Physical Properties 物理性能solidification shrinkage 凝固收缩率freezing range 凝固与熔范围thermal expansion 热膨胀系数specific heat 比热thermal conductivity 热导率electrical conductivity 电导率micro-structure 金相分析hot work tool steel 热作钢circular motion 环形运动variable 变数,参数graphics window 图形窗口45 degree entry and a zero degree exit. 进刀口45度,退刀口0度runner stripper plate 脱料板stripper plate 活动板spacer rock(risers) 间隔板stage ejector 顶棍sprue puller insert 扣针导套guide strip 行位后板afdek plate 挡尘板side gate 大水口pinpoint gate 细水口SHCS 杯头螺丝FHCS 平头螺丝set screw 无头螺丝ball catch 波子螺丝wedge 行位较杯gib 线条,(撑鸡的导轨)latch 拉杆clamp 码仔spring guide pin 弹弓导柱steel pad disc 橙仔方ejector cam insert 斜顶块(screw) nut 螺母taper 嗲把/ 斜度taper interlock 嗲把锁texture 花纹toggle-lok 回撞装置top clamping plate 顶码板unified national coarse (UNC) 美制螺丝(粗牙) unified national fine (UNF) 美制螺丝(幼牙) set screw 喷头螺丝side gate 大水口slide retainer 行位管位water junction 喉咀spacer block 登仔jiffy-matic socket 喉咀套jiffy-tite plug 喉咀公spring plunger 弹弓座sprue puller 勾针/勾粒spring washer 弹簧塑圈stepped ejector pin 有托顶针strippers plate 推板/细水口板submarine gate 潜水口support pin 拉杆support plate 暗板surface finish 光洁度alignment strip 斜锁angle pin 斜针fan gate 扇形入水fillet 圆口ball catch 弹弓波子blade ejector 扁顶bottom clamping plate 底码板free length 自然长度bridge piece 水口铁helix spindle 锅杆hose clip 水喉箍bubbler 隔气运水jiggle 斜顶jiggle witness line 斜顶片位置center distance (CRS) 山打距离(中心线距离)clamp 码仔contour 外形leader pin 导针location ring(flange) 法兰counterbore 拔头,介子托mock-up;prototype 手办die cast 合金压铸national pipe thread(NPT) 美制喉牙overflow 垃圾位ejection sleeve 司筒,顶套epoxy 胶样pin point gate 细水口pressure plug 喉塞pressure spring 压力弹簧parting line flash 披锋burned 烧黑underfilled 缺料insert mismatch 镶件夹口ejector pins not flush 顶针有上下ejector pins skid 顶针滑动insert flash 镶件披锋pressure transducer 压力探测头hydraulic schematic 油积筒油路接驳图jiffy connector recessed 安装喉嘴后不可突出模胚knock out pullback stud -flush with clamp plate 顶棍镶件与底板有否空间safety switches 限位开关stop block 限位块safety strap 平安带drool bushing 防漏胶套筒insert mismatch 镶件夹口EDM visible 明显火花纹lifter scrapes 斜顶拖花short shots 走水不齐wall stock 料位厚薄knit lines 走水纹stress marks 夹水纹uneven fill pattern 走水不平行drag marks 拖花sprue pretrusion 唧嘴突出高度sprue orifice and radil size 唧嘴R尺寸sprue bushing-keyed 唧嘴有管钉English Chineseprogram name 产口名称part name 零件名称tool name 模具名称tool source 模具来源tool steel 模具钢材resin 塑料program number 产品编号part number 零件编号tool number 模具编号customer 客户名称No of cavities 内模编号machine size 啤机吨数drum miller 鼓形铣床duplex horizontal miller 复式卧铣床face miller 端面铣床grinding miller 研磨机plain miller 平面铣床planer-type miller 刨式铣床rack miller 齿条铣床slab miller 大型平面铣床slot miller 键槽铣刀spline miller 花键铣刀thread miller 螺纹铣刀vertical miller 立式铣刀,立辊,立辊轧机endmill 立铣刀plastic mould steel 塑料模钢cold work steel 冷作钢hot work steel 热作钢high speed steel 高速钢electric magnetic clutch 电磁离合器pad printer 移印机screen printer 丝印机hot stamper 烫印机solid carbide slitting saw 钻石钢锯片convex cutter 凸锣刀片concave cutter 凹锣刀片side&face cutters,staggered teeth 正侧双用镶钻石钢锣刀end-mill 锣刀semi-rod 半圆刀split double end 双头刀single end 单头刀2-flute 两辨3-flute 三辨4-flute 四辨reamer 直拈centre drill 中心钻solid carbide drill 钻咀zinc ingot 锌锭aluminium ignot 铝锭tin ignot 锡锭heater cement 发热管的结合剂heater groove 发热管槽spacer rail 介子座cross pin 十字头销nozzle plate 射嘴板nozzle seat 热嘴addendum 齿冠dedendum 齿根air compressor 空气压缩机air exhauster 抽气机air intake 进气口air seal 空气隔离层。
模具零件中英对照及俗称
模具零件中英对照及俗称.txt22真诚是美酒，年份越久越醇香浓型；真诚是焰火，在高处绽放才愈是美丽；真诚是鲜花，送之于人手有余香。
一颗孤独的心需要爱的滋润；一颗冰冷的心需要友谊的温暖；一颗绝望的心需要力量的托慰；一颗苍白的心需要真诚的帮助；一颗充满戒备关闭的门是多么需要真诚这一把钥匙打开呀！中英对照一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口： pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座： connector socket密封/封料： seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝： screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）： mold base上内模：cavity insert下内模：core insert行位（滑块）： slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴： sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.不准用镶件： Do not use (core/cavity) insert用铍铜做镶件： use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper elei模具专业英语词汇dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧楔goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶头冲孔headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢俗称大全广东模具术语深圳方言模具术语: 模胚类: 唧嘴---浇口衬套法兰---定模浇口衬套定位环,扶针---回针, 垃圾钉---顶针板止停销杯头螺丝---内六角沉孔螺丝模具类: 前模---又叫A模或定模, 后模---又叫B模或动模行位---滑块, 钶---镶在后模上的芯子(或叫模仁),机械类工具类: 锣床---铣床, 锣床批土---铣床虎口钳,磨床批土---磨床打直角虎门钳, 匙把揦---活钳或开口扳手的一种称呼刀具工具类: 牙嗒---丝攻, 坑手-攻牙用的扳手, 机转---铁圆规, 奔子---磨成尖头用于敲击划线相交定位点的工具产品类: 止口---夹口美术线,又称遮丑线, 啤把---拨模斜度,火箭脚---位于司柱的加强筋机米螺丝：无头螺丝中山方言模具术语模具类: 斜导柱=斜边锁紧块=铲鸡东莞模具术语：机械工具类：虎钳------批士； C形夹-----虾公码；钻孔------钻窿；加工中心-电脑锣；偷胶-------减胶火山口-------司筒底部的减胶位；公模肉＝后模；母模肉＝前模環保標志=回收章細水口=針點澆口潛水=針點澆口；鑲件=入子；排氣槽=逃氣道披鋒=毛邊；加膠=加料；密封圈=膠圈中托司=頂出導柱(套)=哥林柱水口扣針＝拉料頂針插穿(碰穿)＝靠破曬紋＝咬花波子螺絲＝定位珠开模器=拉胶模胚类：水口边细水口或简化型模胚的从水口板上贯下来的那支导柱中托司顶针板导柱 ;零度块方型辅助器模具类斜顶------斜方水塔，水桶------模仁上钻个深孔，中间用铜片或亚加力板隔开，运水一边进一边出来冷却的水喉，水嘴-----冷却水接口 ;呵----模仁铜公-----放电用的电极 ; 弹弓---弹簧 ; 入水---进胶点模具加工类的飞模------合模好象用白话说的外（音是如此，估计是WIRE）---线切割放电-----打火花 ;省模，打光----抛光光刀---我们这是用来指CNC精加工加工模仁，多用于公模开粗---粗加工，留少许余量开框---模胚上加工放模仁的位置穿线孔---线割时用来穿钼丝的产品类加强筋---加强用的骨位 ; 美工线---上下盖装配的中间的间隙（可有效防上错位）行位 >滑块 ;司筒 >套筒入子 >镶件（INSERT）入子为台灣叫法 ;斜顶 >斜顶块或斜顶杆 KO孔 > 顶棍孔 ;司筒针 > 套筒针撑头 > 支撑柱(防止B板变形的) ;铲鸡 >行位锁紧块治具 > 工具(夹具) ；喉咀 > 水管头；行位波仔 >滑块斜器；中托司 >浇口衬套水口板 >流道板；细水口板 >分流道板勾针 >拉料杆；B板 >动模板；A板 >定模板产品的夹线 >分型线；运水 >冷却水道；回针 >复位顶针；隔热板 >热流道模上用的撬模位 >用来公开AB板的；码模坑 >注射时固定上下模的通框 >把框开成通；大水口模----二板模；小水口模----三板模斜顶(又叫推方)----楣仔方；方铁----凳仔方夹水纹----熔胶线火花纹----电火花加工后留下的纹粗公----电火花粗加工用的铜公精公----电火花精加工用的铜公晒字----做好菲林再拿去加字体的加工方法开模器=拉胶=拉模扣密封圈=膠圈 =防水胶圈=O型圈波子螺絲＝定位珠 =弹弓波子扣机就是控制多板分型的机械装置模具类： K.O孔——顶棍孔——用来顶顶针板的。
常用模具零件中英文对照表
常用模具零件中英文对照表2005-12-19 14:51:17???中国注塑网入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口： pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis :?[??n?l?s?s]流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座： connector socket密封/封料： seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边：guide pin顶针板：ejector retainer plate托板：support plate螺丝： screw管钉：dowel pin ['da??l]开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate ?[?str?p?r] 脱漆剂；脱衣舞演员；剥离剂；剥离器缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock?['na?.lɑn]:斜顶：lifter模胚（架）： mold base上内模：cavity insert下内模：core insert行位（滑块）： slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴： sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞:pipeplug锁模块：lockplate斜顶：anglefrompin斜顶杆：angleejectorrod尼龙拉勾：partinglocks活动臂：leverarm复位键、提前回杆：earlyreturnbar气阀：valves斜导边：anglepin术语：terms承压平面平衡：partingsurfacesupportbalance模排气：partinglineventing回针碰料位：returnpinandcavityinterference模总高超出啤机规格：moldbaseshuthight顶针碰运水：waterlineinterfereswithejectorpin料位出上/下模：partfromcavith(core)side模胚原身出料位：cavitydirectcutonA-plate,coredirectcutonB-plate.不准用镶件：Donotuse(core/cavity)insert用铍铜做镶件：useberylliumcopperinsert初步（正式）模图设计：preliinary(final)molddesign反呵：reversecore弹弓压缩量：springcompressedlength稳定性好：goodstability,stable强度不够：insufficientrigidity均匀冷却：evencooling扣模：sticking热膨胀：theroexpansion公差：tolorance铜公(电极）：copperelectrode塑件模具相关英文词汇出处：FanE『翻译中国』作者：(转载) FanE『翻译中国』 2005-12-16 20:41:59electrical discharge machining (EDM) 电火花加工15. electrical insulating property 电绝缘性能16. electrochemical die-sinking machine 电解型腔加工机，电解型腔加工机床17. electrochemical machine (ECM) 电解加工机床，电化学加工机床18. electrochemical machining (ECM) 电解加工，电化学加工19. electro-discharge cutting 电火花加工，电火花切割20. electro-discharge cutting machine 电火花切割机21. electro-discharge machine tool 电火花加工机床22. Electro-discharge Machine 电火花加工机床23. electro-discharge machining 电火花加工24. electro-discharge machining process 电火花加工工艺，电火花加工工序25. epoxy resin 环氧树脂9. guide bushing 导套10. guide pillar 导柱，导杆，导柱11. guide pin 导向销，导杆12. guide pin cover 导柱盖13. guide plate 导料板，导板14. guide plate blanking die 导板式冲裁模，导板式落料模15. guide post 导柱，导柱16. guide stock plate 挡料板4. injection mold 注射模，注塑模5. injection molding 注射成型，注塑成型6. injection-molding machine 注塑机，注射机，注塑成形机7. injection plunger 注射柱塞8. in-line reciprocating screw 联机往复螺杆，串联往复螺杆，直线排列往复螺杆9. inner ram 内滑块10. inserting molding 嵌件成形11. integrated manufacturing 集成制造12. internal stress 内应力13. intermediate platen 中间板，隔板塑料成型模具的主要设计要素脱模距 stripper distance脱模斜度 draft投影面积 projected area最大开距 maximum daylight;open daylight闭合高度 mould-shut height抽芯距 core-pulling distance抽芯力 core-pulling force脱模力 ejector force开模力 mould opening force模内压力 internal mould pressure;cavity pressure成型压力 moulding pressure背压环 back-up ring1 bar =高压接头 bite type fitting液压马达 hydraulic motor冷却水流量计 waterflow regulator打磨器材 abrasive material打磨砂轮 grinding wheels切割砂轮 cutting wheels码模夹(注塑机使用) mould clamps; lifting clamps 小五金工具 piping tools高压力软管 high pressure hose风管,水软管 air .water hose高压油表 pressure gauge压力油喉 hydraulic hoses光塑检测 photoelastic testing吹塑模 plastic blow mould注塑模 plastic injection mould冲扎复合模 blank & form compound die精密冲模 precision blanking die熔料流动率 MFR=melt flow rate熔料流动指数 MET=melt flow index推板导柱 guide pin for ejector plater座板 clamping plate垫块 space block(plate)推板 ejector block(plate)afdek plate 档尘板guide stripe 行位后板cavity sub-insert 前模镶件core sub-insert 后模镶件sprue puller insert 扣针镶件stage ejector 顶棍spacer rock(risers) 间隔板变形 distortion弯曲 warp拖花 drag marks火花纹 EDM marks困气 venting烧黑 burns表面缩水 shrinkage料位过薄/砸穿 thin wall stock走水不平行 uneven fill pattern夹水纹/流纹 witness line;mismatch;stress marks 走水纹 knit lines走水不齐 short shotsorifice 料口nozzle seat 热嘴垫圈nozzle plate 射嘴板cross pin 十字头销sled 射台seal ring 封密圈spacer rail 介子座heater groove 发热管槽heater cement 发热管的结合剂soak 浸泡seat 垫圈ream 铰大圆孔直径grind 磨床drill 钻床mill 铣床caliper 卡尺G-caliper 分厘卡Depth Gauge 深厚计hardness tester 硬度计angle gauge 角规marble table 云台石projector 投影仪height gauge 高度仪microscope 显微镜plug gauge 塞规leveller 水平器R gauge R 规Inter caliper 内分厘卡surface 平面仪item number 细目编码catalog number 材料分类编码undercut lip 倒扣口hot tip = hot drop = nozzle 热嘴blow-off strip 放气板blow-off nozzle 吹风口spiral hose 螺旋式的连接喉rust solvent 除锈剂shaft 曲轴tensile strength 拉伸力yield strength 屈服力spark erosion 电火花蚀刻etch(photo-etch) 电蚀harden 淬硬copper electrode 铜公corrosion resistance 耐腐蚀anneal 退火heat treatment 淬火FEM(finite elemnet method) 有限元法preliminary tool design 初期模具设计图zone 热流道区域reverse taper 倒啤把clamp plate 码板toggle clamp 快速夹vacuum furnace 真空炉cavity insert rounds 圆柱镶件cavity insert b0locks 方柱镶件tensile strength 抗张强度,抗拉强度Concept drawing 概念图Assembly drawing 装配图mismatch;witness line 夹纹shut-off(n.) 枕位venting valves 疏气阀venting plug 疏气塞valve casing 阀门罩twist drill 旋钻harden/nitride 碎硬anneal 退火temper 回火stess crack 应力断裂corrosion resistance 防腐,防锈tensile strength 物】抗张强度,抗拉强度split mould (分离)组合式的模具inclined plate 斜面inclined bolt 斜栓jaw (工具,机械等)夹住东西的部分,钳口step change of the P/L 分形面枕位的改变thin steel section 较薄的料位clean-up 清理,清除,清扫Mold Dating Insert 模具日志镶件Hot Sprue Bushing 热浇口套semi-automatic 半自动quick disconnector 快速断开接头full shot 足量注射mismatch 夹痕;夹水纹ejector mark 顶痕screw boss 螺丝孔,螺丝基座sink mark 缩坑15% glass filled ABS 掺有15%玻璃的ABS spraying mold release 脱模剂drag mark 拖痕stress mark 应力痕reinforcement rib 加强筋slght stoning 轻度磨砂soliid line 实线dotted line 虚线internal diameter 内径external diameter 外径nickel-plated 电镀的handling hole;lifting hole 吊装孔parallel 平行块piston 活塞plunger 柱塞carrier 导轨rest 支架item number 项目编号catalog item 商品目录编码dimensional datum 尺寸基准heat treatment certification 淬硬证明文件back-up bushing 支撑导套jacking screw 起重螺丝,千斤顶tapped hole (带有螺旋角度的)螺丝孔diagonal corner 成对角的角落burn mark 烧痕hot runner mainfold (热流道板)分流板texuring 蚀纹clamping screw (注塑机)码模螺丝imperial 英制的metric 公制的puller bushing 水口套puller bar 水口铁drool bushing 防漏胶套筒safety switch 限位制water line connected internally or hard tubing 不可用胶喉连接运水lifter on square rod or locked from rotation 用方形柱或用管钉止转gate insert 入水镶件gate shut-offs 流道开关配件guided ejection 中托司parting line shutoff 前后模接触面waterlines clear tie bars. 运水喉咀接驳位要避开啤机呵林柱.BGV=Balanced Gate Value 平衡入水值spacer 垫块pocket 挖槽rough 粗加工finish 精加工plunge rate 进刀率retract rate 提刀速率splindle rate 主轴转速coolant 冷却液SPLIT RING 开口环(钥匙圈)侧向抽芯力 side pulling-core force转图guide pin 边针Tee slot cutter T形SLOT CUTTERzigzag 双向切削constant overlap spiral 等距环切parallel spiral 环绕切削parallel spiral clean corners 环切并清角morph spiral 依外形环绕true spiral 螺旋切削one way 单向end mill 平铣刀spher mill 球刀bull mill 圆鼻刀face mill 面铣刀rad mill 圆角成型刀chamfer mill 倒角刀slot mill 槽刀taper mill 推拔铣刀dove mill 鸠尾铣刀lot mill 棒状drill 钻孔reamer 纹刀bore bar 搪刀tap RH 右牙刀Tap LH 左牙刀ctr Drill 中心钻spot drill 点钻cntr bore 沉头孔刀c. sink 鱼眼孔钻loft surface 举升曲面coons surface 昆氏曲面ruled surface 直纹曲面revolved surface 旋转曲面swept surface 扫描曲面draft surface 牵引曲面grinding wheel 磨砂使用的轮子quench steel 将...淬火,使冷却stress relieving 应力消除molten 熔热的oxide film 氧化层guide pin and sleeve, locating ring ,导边,司筒,定位圈ejector ,ejector balde, ejector sleeve,顶针,扁顶针,顶针司筒, lifters, wear plate,horn pin,斜坊,磨损板,气顶针,O ring, water baffle, water pipe plug,O形圈,隔片,运水管道塞, water line connector,wear plate ,运水管道转接头,耐磨板air cylinder,hydraulic cylinder,氯压缸,液压缸micro switch,oil nipple, spring,开关装置,油枪接头,弹弓sprue bushing,early return system,浇口套,早期回撞装置, accelerated ejectors, slied holder,加速顶针,注塑周期计数器, cycle counter,date stamper，滑块固定板,生产日期铭牌,hot runner system ，热流道系统chemical composition 化学成份thermal conductiivity 导热性能thermal diffusivity 热扩散性能dimensonal stablity 尺寸稳定性能cooling effiency 冷却效率easiler ejection 易于脱模alloy insert 合金镶件(cooling) duct 输送管;导管maintenance cost 维护费用ultrasonic testing 超声波检测crack 断裂direct gate 直接浇口ring gate 环形浇口disk gate;disphragm gate 盘形浇口spoke gate;spider gate 轮辐浇口pin-point gate 点浇口edge gate 侧浇口submarine gate;tunnel gate 潜伏浇口fan gate 扇形浇口tab gate 护耳浇口runner plate 流道板(或冷或热)secondary nozzle 二级喷嘴torpedo;torpedo body assembly 鱼雷形组合体catridge heater 管式加热器heat pipe 热管valve gate 阀式浇口force plunger;pot plunger 柱塞flash groove;spew groove 溢料槽impression;cavity block;cavity plate 凹模punch;force 凸模movable insert;loose detail 活动镶件cavity splits;core splits(凹模拼块) (型芯拼块) 拼块side core 侧型芯thread plug;threaded core 螺纹型芯thread ring;threaded cavity 螺纹型环cutting wheel 切割砂轮grinding wheel 打磨砂轮abrasive material 打磨器材mould clamps;lifting clamp 砂模夹(注塑机使用)air (water) hose 风管,水轮管pressure gauge 高压油表hydraulic hose 压力油喉plastic blow mould 吹塑模plastic injection mould 注塑模blandk&form compound die 冲扎复合模precisiion blanking die 精密冲模MFR=melt flow rate 熔料流动率MFT=melt flow index 熔料流动指数handling hole 拉铃孔stop plate 限位块linder bush 衬套spacer block(plate) 垫块,方铁back-up ring 背位环standoff 限位块American Safety Hoist Rings. 英制安全吊装环Mechanical Properties 机械性能Tensile Strength(MPa) 抗拉强度elongation 延伸率hardness(Brinell) 硬度shear stength(MPa) 剪切力impact strength 冲韧性Physical Properties 物理性能solidification shrinkage 凝固收缩率freezing range 凝固与熔范围thermal expansion 热膨胀系数specific heat 比热thermal conductivity 热导率electrical conductivity 电导率micro-structure 金相分析hot work tool steel 热作钢circular motion 环形运动variable 变数,参数graphics window 图形窗口45 degree entry and a zero degree exit. 进刀口45度,退刀口0度runner stripper plate 脱料板stripper plate 活动板spacer rock(risers) 间隔板stage ejector 顶棍sprue puller insert 扣针导套guide strip 行位后板afdek plate 挡尘板side gate 大水口pinpoint gate 细水口SHCS 杯头螺丝FHCS 平头螺丝set screw 无头螺丝ball catch 波子螺丝wedge 行位较杯gib 线条,(撑鸡的导轨)latch 拉杆clamp 码仔spring guide pin 弹弓导柱steel pad disc 橙仔方ejector cam insert 斜顶块(screw) nut 螺母taper 嗲把/ 斜度taper interlock 嗲把锁texture 花纹toggle-lok 回撞装置top clamping plate 顶码板unified national coarse (UNC) 美制螺丝(粗牙) unified national fine (UNF) 美制螺丝(幼牙) set screw 喷头螺丝side gate 大水口slide retainer 行位管位water junction 喉咀spacer block 登仔jiffy-matic socket 喉咀套jiffy-tite plug 喉咀公spring plunger 弹弓座sprue puller 勾针/勾粒spring washer 弹簧塑圈stepped ejector pin 有托顶针strippers plate 推板/细水口板submarine gate 潜水口support pin 拉杆support plate 暗板surface finish 光洁度alignment strip 斜锁angle pin 斜针fan gate 扇形入水fillet 圆口ball catch 弹弓波子blade ejector 扁顶bottom clamping plate 底码板free length 自然长度bridge piece 水口铁helix spindle 锅杆hose clip 水喉箍bubbler 隔气运水jiggle 斜顶jiggle witness line 斜顶片位置center distance (CRS) 山打距离(中心线距离)clamp 码仔contour 外形leader pin 导针location ring(flange) 法兰counterbore 拔头,介子托mock-up;prototype 手办die cast 合金压铸national pipe thread(NPT) 美制喉牙overflow 垃圾位ejection sleeve 司筒,顶套epoxy 胶样pin point gate 细水口pressure plug 喉塞pressure spring 压力弹簧parting line flash 披锋burned 烧黑underfilled 缺料insert mismatch 镶件夹口ejector pins not flush 顶针有高低ejector pins skid 顶针滑动insert flash 镶件披锋pressure transducer 压力探测头hydraulic schematic 油积筒油路接驳图jiffy connector recessed 安装喉嘴后不可突出模胚knock out pullback stud -flush with clamp plate 顶棍镶件与底板有否空间safety switches 限位开关stop block 限位块safety strap 安全带drool bushing 防漏胶套筒insert mismatch 镶件夹口EDM visible 明显火花纹lifter scrapes 斜顶拖花short shots 走水不齐wall stock 料位厚薄knit lines 走水纹stress marks 夹水纹uneven fill pattern 走水不平行drag marks 拖花sprue pretrusion 唧嘴突出高度sprue orifice and radil size 唧嘴R尺寸sprue bushing-keyed 唧嘴有管钉English Chineseprogram name 产口名称part name 零件名称tool name 模具名称tool source 模具来源tool steel 模具钢材resin 塑料program number 产品编号part number 零件编号tool number 模具编号customer 客户名称No of cavities 内模编号machine size 啤机吨数drum miller 鼓形铣床duplex horizontal miller 复式卧铣床face miller 端面铣床grinding miller 研磨机plain miller 平面铣床planer-type miller 刨式铣床rack miller 齿条铣床slab miller 大型平面铣床slot miller 键槽铣刀spline miller 花键铣刀thread miller 螺纹铣刀vertical miller 立式铣刀,立辊,立辊轧机endmill 立铣刀plastic mould steel 塑料模钢cold work steel 冷作钢hot work steel 热作钢high speed steel 高速钢electric magnetic clutch 电磁离合器pad printer 移印机screen printer 丝印机hot stamper 烫印机solid carbide slitting saw 钻石钢锯片convex cutter 凸锣刀片concave cutter 凹锣刀片side&face cutters,staggered teeth 正侧双用镶钻石钢锣刀end-mill 锣刀semi-rod 半圆刀split double end 双头刀single end 单头刀2-flute 两辨3-flute 三辨4-flute 四辨reamer 直拈centre drill 中心钻solid carbide drill 钻咀zinc ingot 锌锭aluminium ignot 铝锭tin ignot 锡锭heater cement 发热管的结合剂heater groove 发热管槽spacer rail 介子座cross pin 十字头销nozzle plate 射嘴板nozzle seat 热嘴addendum 齿冠dedendum 齿根air compressor 空气压缩机air exhauster 抽气机air intake 进气口air seal 空气隔离层。
模具零件名称中英文对照一览表
模具零件名称中英文对照一览表模具零件名称中英文对照一览表零件名称ENGLISH NAME 零件名称ENGLISH NAME 上固定板TOP CLAMPING PLATE 母模仁CAVITY母模板CAVITY PLATE 公模仁CORE公模板CORE PLATE 母模入子CAVITY INSERT模脚SUPPRORT BLOCK 母模心子CAVITY INSERT PIN上顶出板EJECTOR RET PLATE 母模替换入子CAVITY CHANGEABLE INSERT 下顶出板EJECTOR PLATE 公模入子CORE INSERT下固定板BOTTOM CLAMPING PLATE 公模心子CORE INSERT PIN隔热板THERMAL INSULATING PLATE 公模替换入子CORE CHANGEABLE INSERT 脱料板RUNNER STRIPPER PLATE 滑块入子SLIDE INSERT母模垫板CAVITY SUPPORT PLATE 滑块心子SLIDE INSERT PIN 公模垫板CORE SUPPORT PLATE 斜销入子ANLGE LIFTER INSERT 脱料板STRIPPER PLATE 斜销心子ANLGE LIFTER PIN 流道板RUNNER PLATE 流道开关RUNNER SHUT OFF定位环LOCATING RING T 形块T GIB注口衬套SPRUE BUSHNG U 形块U GIB导柱LEADER PIN 拉料销SPRUE PULLER PIN导套LEADER BUSHING 定位销DOWEL PIN顶板导柱GUIDE PIN 顶针EJECTOR PIN顶板导套GUIGE BUSHING 扁销RECTANGLE EJECTOR PIN 大拉杆LARGE PULLER PIN 套筒EJECTOR SLEEVE小拉杆SMALL PULLER PIN 顶出块EJECTOR BLOCK支撑柱SUPPORT PILLAR 斜销ANGLE LIFTER定位块INTERLOCKS 斜销座ANGLE LIFTER BASE定位柱LOCATION PILLAR 引导块GUIDE BLOCK开闭器(塑料型) FRICTIONAL PULLER 急回推杆LEVER弹簧SPRING 冷却棒THERMAL PIN运输板PL LOCK O 形环O RING零件名称ENGLISH NAME滑块SLIDE 隔水板STRAIGHT BUFFLE滑块座SLIDE BASE 水管接头JIFFY TYTE PLUG滑轨SLIDE RAIL 油封OIL SEAL后跟块HELL BLOCK 内六角螺钉SOCKET HEAD CAP SCREW耐磨板WEAR BLOCK 等高螺钉SOCKET HEAD STRIPPER BLOT 压板RAIL 吊模螺丝EYE BLOT限位块STOP BLOCK 吊环SAFETY HOIST RINGS定位夹SLIDE RETAINER 弹簧垫圈SPRING WASHER定位珠SLIDE RETAINER 加长型水管接头EXTENSION JIFFY TYTE PLUG急回机构POSITIVE EARLY EJECTOR RETURN急回推杆LEVER固定块MOUNT AND COVER PLATE 弹簧片ARM中文名称英文名称中文名称英文名称MOLD BASE内六角螺丝LOCATING RINGEJECTORSPRUE BUSHSPRINGHOT RUNNER无头螺丝SET SCREW CAVITY平头螺丝定位拨珠BALL CATCH前模镶件CAVITY INSERT EJECTOR SLEEVE 后模镶件CORE INSERT BLADE EJECTOR行位(滑块)有托顶针SHOULDER EJECTOR WEDGESPRUE PULLER ANGLE PINWEAR BLOCKPO LOCK JIGGLE导柱辅助器TAPERD SET EJECTOR BLOCK 散打螺丝STRIPPER BOLT STOP BLOCK等高螺丝(拉杆) AS SCREW EJECTION PLATE HYDRAULIC LEADER BLOCK 日期指示器DATE INDICATE WEDGE BLOCK 环保标记章SUPPORT PILLAR AIR JETRM MARKERLOCATING PINGUIDED EJECTION支撑杆(撑头)HYDRAULIC MOTOR塑胶模具常用零件中英文对照表BRONZESEAL RINGSPIRAL TUBESTOP PIN螺旋水套开关装置SWITCHSTAGE EJECTORCOPPER SPACE BLOCK WATER PIPE 液压马达INSERT PIN。
模具常用名称中英文对照表
24. 电极：Electrode——缩写：Elc
25. 限位：LIMIT——缩写：LT
26. 导向板：GUIDE PLATE——缩写GUP
27. 直顶块： STRAIGHT EJ BLOCK——缩写STB
28. 补强板： STIFFENING PLATE——缩写STP
5. 热流道板(热浇道板)：Hot runer——缩写：HR
6. 母模（定模）：Cavity——缩写：Cav
7. 导柱：Guide Pin——缩写：G.P.
8. 导套：Guide bush——缩写：G.B.
9. 复位杆：Release Pin——缩写：R.P.
10. 动模型芯（中间体）：Core——缩写：Cor
11. 模脚：Support parallels——缩写：Supa
12. 侧翼块：Side block——缩写：Sibk
13. 轮Leabharlann ：Plin——缩写：Plin 14. 模座（底座）：Die holder——缩写：Dho
15. 镶件：Insert——缩写：Ins
16. 滑块（行位块）：Slide——缩写：Sld
模具数模命名规则及常用名称中英文对照表（含缩写）
1. 射嘴：Nozzle——缩写：Noz
2. 定位圈：locating ring——缩写：locr
3. 浇口套：Sprue bush(Sprue busing) ——缩写：Sprb
4. 垫板(固定板)：Base Plate——缩写：BP
17. 斜顶块：Lifter——缩写：Lit
18. 推板(顶板)：Eject Plate——缩写：EP
模具零件中英名称对照表
H.P.T A.P STD S.L.T S.T.R E.J.B D.PN F.P P.PN I.B.H E.J.S E.R.D STD M.A.F H-13
E.L.E S-7 P.A.T S.W.P P.U.R C.S.T BRONZE
製表日期：89年11月13日
模具零件圖中英名稱對照表
序 DESC. FINISHED SIZE MATL. Code Name 序 DESC. FINISHED SIZE MATL. Code Name
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
模邊零度束仔 壓 板 滑塊斜撐開銷 斜 梢 螺絲 引 導 塊 擋 塊 推 出 塊 固 定 梢 定 位 梢 拉 出 桿 套 筒 挺射襯 套 頂 出 桿 方形扁頂針 無頭螺絲 熱料道 板 隔熱墊塊 熱澆道灌嘴 熱澆道加熱管 油壓缸 O型環 電 極 壓塊 另 件 螺 桿 拉 環 石 膏 耐摩板
S.C.A M.C.R
G.P(L.P) G.B.H(L.B.H)
RP ST SET E.G.P E.G.B SP S.T.B S.T.P C.P S.P.P
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
TOP PLT 上固定板 STRIP PLT 三板模脫料板 CAV. PLT 母模板 CORE PLT 公模板 CORE BACKING PLT 公模墊板 SPACER BLOCK(RAIL) 間隔板 EJ. RET. PLT 上頂出板 EJ. PLT 下頂出板 BOTTOM PLT 下固定板 CAVITY 母 模 仁 CORE or FOROE 公 模 仁 CORE INSERT 公仁入仔 CAV. INSERT 母仁入仔 GUIDE PIN(LEADER PIN) 導 柱 (桿) GUIDE (LEADER) BUSHING 導銷襯套 LOC. RING 固定環 SPURE BUSH 進料灌嘴 RET PIN 回位銷 STOP PIN 停止銷 SET PIN 角位銷 EJECT GUIDE PIN 打板導 桿 EJECT GUIDE BUSHIN 打板導桿襯套 SPRING 彈簧 SUPPORT 公模板支撐柱 STRIPPER BOLTS 制止螺 絲 PULLER BOLTS 拖拉螺 桿 INTERLOCK 模面固定束仔 CORE PIN 心 型 梢 SPRUE PULLER 注道拉出梢 SLIDE 滑塊
UGNX模具设计注塑模中英文对照
UGNX模具设计注塑模中英文对照附录A1（中英文对照表-零件类1）中文名称英文名称中文别称1. 零件类（模板）模架mold base 模胚隔热板thermal insulation board定模座板top clamping plate 定模底板、面板热流道板hot runner manifold 分流板推流道板runner stripper plate 脱料板、水口推板、水口板型腔固定板cavity plate 定模板、定模框、A板、母模推件板stripper plate 脱模板型芯固定板core plate 动模板、动模框、B板、公模支承板support plate 垫板、托板垫块spacer block 模脚、方铁、登仔推杆固定板ejector retainer plate 顶针固定板、面针板推板ejector plate 推顶杆板、顶针垫板、底针板动模座板bottom clamping plate 动模底板、底板2. 零件类（浇注系统）定位圈locating ring 定位环、法蓝浇口套sprue bushing 浇口衬套、唧咀、唧嘴浇口镶块gating insert 入水镶件拉料杆sprue puller 拉料销、水口勾针热流道系统hot runner system流道板runner plate温流道板warm runner plate分流锥sprue spreader二级喷嘴secondary nozzle鱼雷形组合体torpedo body assembly管式加热器cartridge heater 筒式加热器热管heat pipe 导热管加热圈heating ring热电偶thermocouple 探针、探温针阀式热嘴valve gating nozzle 阀针式热嘴、阀节喷嘴阀针valve pin热嘴hot nozzle 热喷嘴热嘴垫圈nozzle seat3. 零件类（顶出系统）推杆ejector pin 顶杆、顶针带肩推杆shouldered ejector pin 阶梯推杆、台阶顶针扁推杆flat ejector pin 扁顶杆、扁顶针推管ejector sleeve 司筒、顶管、套筒推管芯子ejector sleeve pin 中心销、司筒针中文名称英文名称中文别称3. 零件类（顶出系统）推块ejector pad 顶块推件环stripper ring 脱模圈斜顶杆angle ejector rod 斜导杆斜顶lifter自润滑活型芯组件slide core guide unit 斜顶滑座导滑座slide base斜导杆固定座angle ejector rod fixed seat自润滑板guide plate挡块baffle block挡块固定螺钉baffle block set screw复位杆return pin 回程销、回针限位块stop block 止动件限位钉stop pin 垃圾钉4. 零件类（成型零部件）型腔cavity 母模仁型芯core 公模仁、模芯侧型芯side core 侧模芯镶件mould insert 镶块型腔镶件cavity insert 上内模、母模入子型芯镶件core insert 下内模、公模入子活动镶件movable insert 拼块split螺纹型芯threaded core螺纹型环threaded cavity嵌件insert镶针insert pin5. 零件类（温度调节系统）快速接头jiffy quick connector管接头hose nippler三通接头three way cock四通接头four-way connection弯管接头pipe bend水嘴water nozzle 水接头油嘴oil nozzle 油接头软管hose 喉管水管water tube油管oil tube气管air tube中文名称英文名称中文别称5. 零件类（温度调节系统）管夹hose clip 软管卡子丝堵pipe plug 螺塞、喉塞冷却管cooling pipe隔水片baffle 挡水板O形圈o-ring 密封圈、O形环止水栓stopcock 导流塞流量计flow meter集水器siamese 集水块集油器oil collector 集油块节流阀throttle valve 截流阀流量分配器flow divider 分流器6. 零件类（侧向分型与抽芯机构）滑块slide 行位斜导柱angle pin 斜销、斜导边弯销clog-leg cam锁紧块locking block 楔紧块、铲鸡滑块导板slide glide strip 滑块导轨、压条耐磨板wear plate 硬片、油板球头顶丝ball plunger 波子螺丝、波子弹弓限位块stop block 止动件滑块定位器slide retainer 行位管位7. 零件类（导向、定位系统）导柱guide pin 边钉、导边直身导柱straight leader pins 直导柱带肩导柱shoulder leader pin 台阶导柱推板导柱ejector guide pin 中托边方型导柱guide square 方导柱三板模导柱support pins 细水口导边、水口边三板模导套runner stripper plate bushing 水口板导套、水口套导向条gib block 导向块导套guide bushing 边司直导套straight bushing带肩导套shoulder bushing 有托导套推板导套ejector guide bush 中托司套定位销dowel pin 销钉、管钉定位块locating block直身锁side lock 边锁、侧锁扣、直身定位块斜度锁taper lock 斜度定位块中文名称英文名称中文别称8. 零件类（开关模控制）定距拉杆puller bolt 拉杆螺丝、拉杆定距拉板puller plate 拉板止动螺钉stop bolt 限动螺栓锁模板safety bar 安全杆、锁模扣、安全扣阻尼销parting locks 尼龙拉钩、树脂开闭器、拉模扣分型面锁模装置parting lock set 分型拉钩、扣鸡、扣机顶出预复位机构early ejector return 早回机构、先复位机构9. 零件类（其他功能件）螺钉screw 螺丝螺帽screw cap 螺丝帽内六角螺钉shcs 杯头螺丝内六角沉头螺钉fhcs 平头螺丝无头螺丝grub screw弹簧spring 弹弓圆线弹簧wire spring扁弹簧flat spring氮气弹簧gas spring齿轮gear wheel轴承bearing马达motor止动键locking key卡簧clamp spring油缸hydraulic cylinder 液压缸气缸air cylinder排气阀air evacuation valve支撑柱support pillar 支承柱、撑头承压块pressure block吊模块lifting bars for mold 模具起吊块吊环lifting eye bolts 吊环螺钉挤紧块clamping block 锁定块垫圈washer 垫片弹簧垫圈spring washer 弹垫标牌nameplate铭牌保护盖protective cover 防护罩顶模块ejector rod 顶出杆、顶棍行程开关position limit switch 限位开关计数器counters中文名称英文名称中文别称9. 零件类（其他功能件）压力传感器pressure transducer日期章date markers 日期标记电源插座power socket公插male connector母插female connector电线electric wire接线盒connection box 接线箱保护盒protection box保护柱stand off调整板adjustment plate压板stopper plate中文名称英文名称中文别称10. 相关术语类(设计系统)模具工程mold engineering工程力学engineering mechanics工程热力学engineering thermodynamics流变学rheology塑料成形模具mould for plastics 塑料模、塑胶模注射模injection mould 注塑模注射模设计design of injection mould 热塑性塑料注射模injection mould forthermoplastics热固性塑料注射模injection mould for thermoses双色模double-color mould叠层模stack injection mould热流道模hot runner mould绝热流道模insulated runner mould 温流道模二板模two plate mold 大水口模三板模three plates mold 细水口模浇注系统feed system冷流道系统cold runner system主流道sprue 注入口、注道分流道runner浇口gate 入水浇口形式gate type 入水形式浇口大小gate size 入水大小浇口位置gate location 入水位置直接浇口direct gate 大水口环形浇口ring gate 环型浇口盘形浇口dish gate轮辐浇口spoke gate点浇口pin-point gate 细水口、针点式浇口侧浇口edge gate 边缘浇口潜伏浇口submarine gate 潜水口隧道式浇口tunnel gate 月牙形浇口、牛角形浇口、香蕉形浇口冷料穴cold-slug well 冷料井溢料槽flash groove 跑胶道、流胶沟排气槽air vent 排气道、排气孔、疏气位分型面parting surface 分模面分型线parting line 分模线中文名称英文名称中文别称10. 相关术语类(设计系统)水平分型面（线）horizontal parting line垂直分型面（线）vertical parting line定模fixed half 固定侧动模moving half 可动侧排气系统vent system顶出系统ejection system 脱模系统顶出机构ejection mechanisms 脱模机构成型零部件molding parts冷却系统cooling system冷却通道cooling channel加热系统heating system 供热系统收缩率shrinkage 缩水抽芯力core-pulling force抽芯距core-pulling distance投影面积projected area脱模斜度draft 拔模斜度模具寿命die life模腔数cavity number11. 相关术语类(注塑成型)注射机injection molding machine 注塑机、射出成型机、啤机注射能力shot capacity 注塑容量、注塑能力注射压力injection pressure 注塑压力、射胶压力锁模力clamping force 合模力成型压力moulding pressure 成形压力模内压力internal mould pressure 型腔压力开模力mould opening force脱模力ejection force 顶出力闭合高度mould-shut height最大开距maximum daylight 模板开距脱模距stripper distance最大容模厚度max mold height 最大模厚最小容模厚度min. mould thickness 最小模厚拉杆内距space between tie bars 拉杆间距、导柱内距注射装置injection unit 射胶系统预塑化装置preplasticator合模装置clamping unit 锁模系统控制装置control unit 控制系统机械手mechanical arm 机械臂中文名称英文名称中文别称11. 相关术语类(注塑成型)快速换模系统quick die change system 快速换模装置顺序阀sequence valve喷嘴直径nozzle diameter喷嘴球半径nozzle radius成型周期molding cycle 模塑周期注射时间injection time 射出时间保压时间packing time冷却时间cooling time顶出时间ejection time 脱模时间开、合模时间time of mold open & close塑料Plastics 塑胶塑件plastic parts 塑胶件项目名称project name产品名称product name 品名外观件appearance part总产量total product电镀plating 喷镀油漆paint蚀纹texture 咬花光面shiny side热板焊hot plate welding超声波焊ultrasonic welding 超声焊摩擦焊friction welding振动焊vibration welding壁厚wall thickness加强筋rib圆角fillet尖角sharp corner 锐角、利角凸台convex plate文字text孔位hole location工艺分析process analysis 过程分析流动分析flow analysis 充填分析顶白ejected mark 顶痕毛刺burr 毛边缩痕sink mark 凹痕水波痕water wave effect表面光泽度不良gloss ng中文名称英文名称中文别称11. 相关术语类(注塑成型)银丝纹silver streak 银条纹、银丝气泡bubble黑条纹dark streak烧焦burn 烧伤、烧黑黑点black spots 黑色斑翘曲warpage熔接线weld lines 熔合线熔接痕welding mark 溶合痕尺寸不稳定dimensional instability裂痕flaw 裂缝变色discoloration 褪色困气air trapping缺胶short shot 充填不足、欠注、短射试模mold trial注射速度injection rate 注射速率干燥温度drying temperature 烘干温度干燥时间drying time 烘干时间成型温度injection temperature 注塑温度、喷射温度模具温度mould temperature12. 相关术语类(材料)模板mould plate标准件standard parts电极electrode铜电极copper electrode 铜公石墨电极graphite electrode钨电极tungsten electrode钢steel 钢铁、钢材热作钢hot work tool steel 热锻模具钢冷作钢cold work steel预硬钢prehardened steel碳素钢carbon steel 碳钢碳素工具钢carbon tool steel不锈钢stainless steel铬钼钢chrome molybdenum steel合金工具钢alloy tool steel高速工具钢high speed tool steel硬质合金钢hard alloy steel弹簧钢spring steel中文名称英文名称中文别称12. 相关术语类(材料)灰口铸铁grey cast iron 灰铸铁、灰口铁紫铜copper黄铜brass青铜bronze铍铜BeCu铍青铜beryllium bronze铝aluminum13. 相关术语类(技术参数)结晶性crystallinity 结晶度透明性transparency 透明度耐热性heat resistance 抗热性熔融指数melt index 熔体流动指数剪切速率shear rate 剪切率剪切应力shear stress摩擦系数frictional coefficient布氏硬度brinell hardness HB洛氏硬度rockwell hardness HRC肖氏硬度shore hardness Hs维氏硬度vickers hardness HV金属疲劳metal fatigue疲劳寿命fatigue life密度density重量weight重心centre of gravity面积area体积volume承压面积bearing area 支承面积雷诺数reynolds number导热性thermal conductivity 导热率、导热系数比热容specific heat 比热热量heat quantity温差temperature difference弹性模量modulus of elasticity 弹性模数、杨氏模量截面惯性矩second moment of area 截面二次轴矩截面模量section modulus 截面系数泊松比poisson ratio 横向变形系数拉伸强度tensile strength 抗拉强度压缩强度compressive strength 抗压强度中文名称英文名称中文别称13. 相关术语类(技术参数)屈服强度yield strength剪切强度shear strength 抗剪强度冲击强度impact strength 抗冲强度扭曲强度torsional strength 抗扭强度、扭转强度弯曲强度bending strength 抗弯强度、抗挠强度屈服应力yield stress 延展率elongation 延伸率载荷load弹性变形elastic deformation 弹性形变热膨胀系数thermal expansion coefficient14. 相关术语类(表面处理)热处理heat treatment调质thermal refining TR渗碳carburizing退火annealing回火tempering氮化nitriding NT、渗氮真空氮化vacuum nitriding 真空渗氮真空渗碳氮化vacuum carbonitriding 真空碳氮化离子氮化plasma nitriding离子渗碳氮化ion carbonitriding淬火quenching hardening QH高频淬火high frequency hardening真空淬火vacuum hardening化学电镀chemical plating 化学镀阳极氧化处理anodizing 阳极氧化发黑blackening 染黑法喷砂处理sand blast时效处理seasoning15. 相关术语类(加工)加工中心机床machine centers 加工中心CNC铣床cnc milling machine 数控铣床高速铣床high speed milling machine仿形铣床profiling milling machine 靠模铣床仿形车床copy lathe 靠模车床锯床saw machine刨床planing machines磨床grinding machines中文名称英文名称中文别称15. 相关术语类(加工)车床lathe摇臂钻床radial drilling machine 旋臂钻床钻床drilling machine 钻孔机雕刻机engraving machines电火花机electric discharge machines 火花机线切割放电机wire E.D.M. 线割放电加工机测量机measuring machines三座标测量仪three-coordinates measuringmachine合模机die spotting machine机加工machining 切削加工锻造forging铸造casting精密压铸accurate die casting电铸electroforming热轧hot rolling HR冷轧cold rolling 冷压延拉拔draw out挤压extrusion 挤制加工锯削sawing雕削carving-and-scraping铣削milling镗削boring锉削加工filing车削turning钻孔drilling铰孔reaming 铰孔修润拉削broaching刮削scraping磨削grinding研磨加工lapping切削cutting砂纸加工coated abrasive machining抛光加工polishing 抛亮光电火花加工electrical discharge machining 放电加工、EDM 线切割加工spark-erosion wire cutting WEDM电解研磨electrochemical lapping化学研磨chemical polishing中文名称英文名称中文别称15. 相关术语类(制图)技术制图technical drawing 工程制图技术参数technical parameter表面粗糙度surface finish 表面光洁度公差与配合common difference &cooperation形位公差geometric tolerance 几何公差尺寸公差dimension tolerance公差范围tolerance limits 容差极限基孔制basic hole system基轴制basic shaft system三角函数trigonometric function装配图assembly drawing 组装图、总装图、组合图模具排位图die layout 结构草图零件图part drawing 散件图工艺图process drawing 工艺过程图件号no.名称designation实际尺寸actual size标准尺寸stock size材质material 材料、物料数量quantity订货号order no. 订单号备注remarks 附注供应商supplier 供货商模号mold no设计design审核checked by 核对批准approve 审批比例scale单位unit张次sheet版本revision 版次图纸大小drawing sheet size模具公差mold tolerance日期date客户customer技术要求technical requirement 技术条件、技术规定使用说明书operation specifications 操作规范中文名称英文名称中文别称16. 相关术语类(流程、商务)流程优化process optimization 过程优化时间计划表time schedule 工作进度表、时间安排表设计优化design optimization产品分析报告product analysis report流动分析报告flow analysis report结构分析报告structural analysis report模具性能与寿命分析analysis of performance andlife of mold行政部administrative department 行政司营销部marketing department 市场部、市场销售部项目部project department工程部engineering department技术部technical department 技术研发部制造部manufacture department 生产部质检部quality inspection department 品保部采购部purchasing department财务科finance section客服部customer service department 客户服务部董事长board chairman 董事局主席总经理general manager技术总监technical director工程部经理engineering manager制造部经理manufacturing manager 生产部经理模具项目经理mold project manager模具设计师mould designer模具分析师mould analyst项目工程师project engineer钳工fitter模具成本mold cost 模具费用利润profit报价单quotation设计成本design cost 设计费制造成本manufacturing cost 生产成本材料成本material cost 物料成本调试成本debugging cost 调试费用管理成本administration cost 管理费税收revenue 交期delivery time 发货期、交货期。
模具厂常用模具零件规范名称
模具厂常用模具零件规范名称自建厂以来,由于种种原因,厂内对模具的叫法不一,时常会产生一些误会,不利于工作的开展,所以很有必要对常用模具零件的名称加以规范。
为此,特对我厂常用模具零件名称作如下统一规范。
请设计部、生产部等有关部门自本规范公布之日起,按此规范名称(加粗黑体字所示给模具零件命名。
(英文名仅供参考,不得用于厂内的生产图中序号类别规范名称曾用名参考英文名备注1 板类上码模板面板 Clamping Plate2 板类 A板定模板 Cavity Support Plate3 板类 B 板动模板 Core Support Plate4 板类方铁凳仔方 Riser Bar5 板类顶针板面针板 Ejector Plate A6 板类顶针托板底针板 Ejector Plate B7 板类下码模板底板 Setting Plate8 板类模胚模架 Moldbase9 板类热流道板 Hot Runner Plate10 板类隔热板 Insulator Sheet11 板类托板 Support Plate12 镶件类前模镶件上模镶件 Cavity Support Plate Insert13 镶件类前模镶件上模镶件 Cavity Support Plate Insert Pin14 镶件类型腔镶件下模镶件 Core Insert15 镶件类型芯镶件下模镶件 Core Insert Pin16 镶件类后模镶件下模镶件 Core Support Plate Insert17 镶件类后模镶件下模镶件 Core Support Plate Insert Pin18 镶件类环保镶件环保印 Recycling Insert19 镶件类铍铜镶件 BeCu Insert20 镶件类日期镶件日期印 Dating Insert21 镶件类铜镶件 Copper Insert22 镶件类斜导柱压块斜边镶件 Angle Pin Insert23 镶件类滑块镶件行位镶件 Slide Insert24 镶件类前模型芯型腔 Cavity25 镶件类后模型芯型芯 Core26 镶件类排气镶件 Sintered Insert27 镶件类前模互换镶件 Interchangeable Insert28 镶件类后模互换镶件 Interchangeable Insert29 结构件滑块行位 Slide30 结构件滑块导向块 Slide Guide Rain31 结构件斜顶导向块32 结构件斜顶压条33 结构件行位夹 Slide Retainer34 结构件滑块压条压板 GIB35 结构件斜导柱斜边 Angle Pin36 结构件斜顶 Lifter Jiggle序号类别规范名称曾用名参考英文名备注37 结构件斜顶座 Heel Block38 结构件加速顶 Accelerated Ejector39 结构件 T 形块‘T’Slide40 结构件 T 形接头‘T’Junction41 结构件铲基铲机 Jaw42 结构件 U形销‘U’Pin43 结构件导轨 Guide Way44 结构件直顶方顶 Straight Ejector45 结构件推方 Stripper Block46 结构件围方 Surrounded Bar47 结构件护角 Guided Corner48 结构件耐磨块硬片 Wear Block49 结构件扣机 Latch Lock50 结构件拉板 Pull Plate51 标准件杯头螺丝内六角圆柱头螺钉S.H.C.S52 标准件机米螺丝内六角紧定螺钉Screw Plug53 标准件山打螺丝 Shoulder Bolt54 标准件平头螺丝十字槽沉头螺丝F.H.C.S55 标准件司筒顶管 Ejector Sleeve56 标准件顶针 Ejector Pin57 标准件 KO接头 K.O.Adapter58 标准件衬垫 Cushion59 标准件撑头支撑柱 Support Pillar60 标准件齿轮 Gear61 标准件齿条 Rack62 标准件齿轴 Gear Draft63 标准件单车链链条 Chain64 标准件导套 Leader Bushing65 标准件导柱 Leader Pin66 标准件垫圈戒指 Washer67 标准件吊环 Eyebolt68 标准件吊模板吊模方 Eyebolt Plate69 顶辊 Ejector Rod70 顶针板导套顶出板导套Ejector Guided Bushing71 定位圈法兰 Locating Ring72 防水胶圈密封圈‘O’Ring73 弹簧扶针 Spring Retainer序号类别规范名称曾用名参考英文名备注74 隔水片水塘 Baffle75 定位销管钉 Dowel Pin76 喉嘴 Male Plug77 加长喉嘴 Extension Plug78 直接头79 快换接头80 黄弹簧黄弹弓 Yellow Spring81 蓝弹簧蓝弹弓 Blue Spring82 回针复位杆 Return Pin83 唧嘴浇口套 Sprue Bushing84 集流板集水板 Water Manifold85 计数器 Counter86 垃圾钉 Stop Pin87 拉模扣尼龙扣 Parting Lock88 螺孔拉杆小拉杆 Puller Bolt89 螺栓拉杆 Stopper Bolt90 拉杆套91 气阀 Air Poppet V alve92 气针 Gas Pin93 水管 Bubbler Tube94 水口钩针 Sucker Pin95 锁模板安全锁 Safety Strap96 条形锁 Rectangular Lock97 铜堵头 Brass Plug98 限位块 Stopper99 行程开关 Switch100 油缸 Hydraulic Cylinder101 圆形锁 Round Lock102 直身锁边锁 Side Lock103 先复位摆杆104 先复位顶杆105 先复位挡块106 先复位导向块107 先复位衬套自本标准公布之日起,所有图纸和有关单据均应采用常用模具规范名称。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
RIN
date t
Din
O ring
"O"
compressor spring SPR
elongate spring EPR
angular pin
AP
stopper block STOB
CSH.screw
BCWCSH
SHC.Screw
BSW
SS.Screw
SS
SHS.Screw
SHS
Ball.plungers
a plate
A
b plate
B
stripper plate
ST
support plate
SP
support spacer
C
bottom clamp plate BP
ejector retainer plate ERP
ejector plate
EP
guide pin
GP
shoulder guide bush SHB
tube heater
TLH
coil heater
COH
band heater
BH
cartridge heater CTH
themocouple
THP
valve nozzle
VN
open nozzle
OPN
connecting box CB
gear wheel
GW
gear rack
GRS
bearing
PinM
core insert
InsC
core pin
PinC
slant ejector
SE
中文
模胚 大水口模胚 简化型细水 口模胚 细水口模胚 面板 水口板 A板 B板 推板 托板 方铁 底板 面针板 底针板 导柱 托司 直司 拉杆 回针 顶针 扁顶针 司筒 司筒针 推方 推销 拉板 勾针 限位钉 撑头 水口螺丝 定距拉杆 定位销 定位圈 唧嘴 型腔 型芯 型腔镶块 型腔镶针 型芯镶块 型芯镶针 斜顶
straight guide bush
STB
support pin
PBA
return pin
RP
ejector pin
EP
ejector blade
EB
ejector sleeve
ES
ejector sleeve pin
ESP
steipper block
SB
steipper pillar
STP
puller plate
slider
SLD
滑块
Ejector guide pin EGP
中托司
BPS
CSH.Screw.Hole CH
Screw.Hole
SH
SHS.Screw.Hole SSH
parting lock set PLS
frictional puller NLK
manifold block MAB
upper support USP
lower support CSP
tubular heater TH
英文名
简写
heel locking block LSB
guide rails
GRS
wear plate
WPT
angular cam
ANC
tapered interlock TIN
hydraulic unit HU
cylinder unit
CU
hot sprue busing HSB
recycle insert
BOT
puller pin
RLA
stop disc
STOP
support pillar
SP
stopper bolt
SBT
stopper pin
STP
dowel pin
DP
locating ring
LR
sprue bushing
SBS
cavity
Cav
core
Cor
cav.insert
InsM
cav.pin
工程部模具零件名中英文对照表
英文名
简写
mould base
MB
side gate mold base S-
three plate type mold plate
T-
pin point gate mold plate P-
top clamp plate
TP
Runner stripper plate RSP
BEA
hose barb
HB
中文
滑块压板 弯销
耐磨板
锥度边钉 油唧 水压缸 气缸 热唧嘴 环保镶件 日期镶件 密封圈 压缩弹簧 拉伸弹簧 斜导柱 限位板 平头螺丝 杯头螺丝 无头螺丝 塞打螺丝 波子螺丝 平头螺丝孔 螺丝过孔 塞打螺丝孔 拉勾 尼龙拉钩 流道板 上压垫 中心垫 电热线 电热筒 电热线圈 电热环 电热管 热电偶 阀式注嘴 开式注嘴 接线盒 齿轮 齿条 轴承 水喉