塑料专业名词中英文
塑料模具行业专业术语中英文对照
塑料模具中英语对照塑料模具英语入水:gate 进入位：gate location 水口形式:gate type 大水口：edge gate细水口：pin—point gate 水口大小：gate size 转水口:switching runner/gate唧嘴口径：sprue diameter二、流道：runner热流道：hot runner，hot manifold 热嘴冷流道: hot sprue/cold runner唧嘴直流：direct sprue gate 圆形流道：round（full/half runner流道电脑分析:mold flow analysis 流道平衡:runner balance热嘴：hot sprue 热流道板：hot manifold发热管：cartridge heater 探针: thermocouples插头：connector plug 插座：connector socket密封/封料：seal三、运水：water line 喉塞：line lpug喉管：tube塑胶管：plastic tube 快速接头：jiffy quick connectorplug/socker四、模具零件：mold components三板模：3—plate mold 二板模：2-plate mold边钉/导边:leader pin/guide pin 边司/导套：bushing/guide bushing中托司：shoulder guide bushing 中托边L：guide pin顶针板：ejector retainner plate 托板：support plate螺丝：screw 管钉：dowel pin开模槽：ply bar scot 内模管位：core/cavity inter—lock 顶针：ejector pin 司筒：ejector sleeve司筒针:ejector pin 推板：stripper plate缩呵：movable core,return core core puller扣机(尼龙拉勾）：nylon latch lock 斜顶：lifter模胚（架)：mold base 上内模：cavity insert下内模：core insert 行位(滑块）：slide镶件:insert 压座/斜鸡：wedge耐磨板/油板：wedge wear plate 压条:plate撑头：support pillar 唧嘴：sprue bushing挡板：stop plate 定位圈：locating ring锁扣：latch 扣鸡：parting lock set推杆:push bar 栓打螺丝：S。
塑料术语专业英语词汇
塑料术语专业英语词汇(1)氨基树脂amino resin由含有氨基的化合物如脲或三聚氰胺与醛类或可生成醛的物质缩聚制得的聚合物。
氨基塑料aminoplastics以氨基树脂为基材的塑料。
暗泡bubble塑料成型时，由于残留的空气或其他气体而在制品内部形成的气泡缺陷。
板材plate一般指厚度在2毫米以上的软质平面材料和厚度在0.5毫米以上的硬质平面材料。
瓣合式模具split mould由两个或多个元件组成模腔并用模套箍紧的一种压制模具。
半透明性translucence物体只能透过一部分可见光，但不能通过它清晰地观察其他物体的性质。
半溢料式模具semi-flash mould压缩模塑中只允许有限物料在闭模时溢出的模具。
半硬质塑料semirigid plastics按GB1040-79《塑料拉伸试验方法》测定，拉伸弹性模量在700~7000公斤力/厘米2约70~700 108（帕）之间的塑料。
标准环境按照GB1039----79《塑料力学性能试验方法总则》的要求选取。
包封encapsulation用涂刷、浸涂、喷涂等方法将热塑料性或热固性树脂施加在制件上，并使其外表面全部被包覆而作为保护涂层或绝缘层的一种作业。
薄膜film一般指厚度在0.25毫米以下的平整而柔软的塑料制品。
爆破强度bursting strength塑料容器、管材、薄膜等在爆破试验时所能受液体或空气对其连续施加的最大压力。
刨纹shecter lines刨痕切削操作过程中，在塑料片材料上所产生的大面积平行刮痕或沟纹状的缺陷。
保压时间hold up time（1）注射成型时，指在塑料充满模腔后对模内塑料保护规定压力实行补料的一段时间。
（2）压缩模塑时，指将物料压入模腔放气后压力升到预定值至开始解除压力的时间。
苯胺甲醛树脂aniline formaldehyde resim由苯胺与甲醛缩聚制得的一种氨基树脂。
本体聚合（作用）bulk polymerization,mass polymeriza-tion除加催化剂或引发剂外，不加任何其他介质（如稀释剂或溶剂）而使单体（通常为液体）进行的聚合。
塑料中英文简称全称
英文简称英文全称中文全称ABA Acrylonitrile-butadiene-acrylate 丙烯腈/丁二烯/丙烯酸酯共聚物ABS Acrylonitrile-butadiene-styrene 丙烯腈/丁二烯/苯乙烯共聚物AES Acrylonitrile-ethylene-styrene 丙烯腈/乙烯/苯乙烯共聚物AMMA Acrylonitrile/methyl Methacrylate 丙烯腈/甲基丙烯酸甲酯共聚物ARP Aromatic polyester 聚芳香酯AS Acrylonitrile-styrene resin 丙烯腈-苯乙烯树脂ASA Acrylonitrile-styrene-acrylate 丙烯腈/苯乙烯/丙烯酸酯共聚物CA Cellulose acetate 醋酸纤维塑料CAB Cellulose acetate butyrate 醋酸-丁酸纤维素塑料CAP Cellulose acetate propionate 醋酸-丙酸纤维素CE Cellulose plastics, general 通用纤维素塑料CF Cresol-formaldehyde 甲酚-甲醛树脂CMC Carboxymethyl cellulose 羧甲基纤维素CN Cellulose nitrate 硝酸纤维素CP Cellulose propionate 丙酸纤维素CPE Chlorinated polyethylene 氯化聚乙烯CPVC Chlorinated poly(vinyl chloride) 氯化聚氯乙烯CS Casein 酪蛋白CTA Cellulose triacetate 三醋酸纤维素EC Ethyl cellulose 乙烷纤维素EEA Ethylene/ethyl acrylate 乙烯/丙烯酸乙酯共聚物EMA Ethylene/methacrylic acid 乙烯/甲基丙烯酸共聚物EP Epoxy, epoxide 环氧树脂EPD Ethylene-propylene-diene 乙烯-丙烯-二烯三元共聚物EPM Ethylene-propylene polymer 乙烯-丙烯共聚物EPS Expanded polystyrene 发泡聚苯乙烯ETFE Ethylene-tetrafluoroethylene 乙烯-四氟乙烯共聚物EVA Ethylene/vinyl acetate 乙烯-醋酸乙烯共聚物EVAL Ethylene-vinyl alcohol 乙烯-乙烯醇共聚物FEP Perfluoro(ethylene-propylene) 全氟（乙烯-丙烯）塑料FF Furan formaldehyde 呋喃甲醛HDPE High-density polyethylene plastics 高密度聚乙烯塑料HIPS High impact polystyrene 高冲聚苯乙烯IPS Impact-resistant polystyre ne 耐冲击聚苯乙烯LCP Liquid crystal polymer 液晶聚合物LDPE Low-density polyethylene plastics 低密度聚乙烯塑料LLDPE Linear low-density polyethylene 线性低密聚乙烯LMDPE Linear medium-density polyethylene 线性中密聚乙烯MBS Methacrylate-butadiene-styrene 甲基丙烯酸-丁二烯-苯乙烯共聚物MC Methyl cellulose 甲基纤维素MDPE Medium-density polyethylene 中密聚乙烯MF Melamine-formaldehyde resin 密胺-甲醛树脂MPF Melamine/phenol-formaldehyde 密胺/酚醛树脂PA Polyamide (nylon) 聚酰胺（尼龙）PAA Poly(acrylic acid) 聚丙烯酸PADC Poly(allyl diglycol carbonate) 碳酸-二乙二醇酯·烯丙醇酯树脂PAE Polyarylether 聚芳醚PAEK Polyaryletherketone 聚芳醚酮PAI Polyamide-imide 聚酰胺-酰亚胺PAK Polyester alkyd 聚酯树脂PAN Polyacrylonitrile 聚丙烯腈PARA Polyaryl amide 聚芳酰胺PASU Polyarylsulfone 聚芳砜PAT Polyarylate 聚芳酯PAUR Poly(ester urethane) 聚酯型聚氨酯PB Polybutene-1 聚丁烯-[1]PBA Poly(butyl acrylate) 聚丙烯酸丁酯PBAN Polybutadiene-acrylonitrile 聚丁二烯-丙烯腈PBS Polybutadiene-styrene 聚丁二烯-苯乙烯PBT Poly(butylene terephthalate) 聚对苯二酸丁二酯PC Polycarbonate 聚碳酸酯PCTFE Polychlorotrifluoroethylene 聚氯三氟乙烯PDAP Poly(diallyl phthalate) 聚对苯二甲酸二烯丙酯PE Polyethylene 聚乙烯PEBA Polyether block amide 聚醚嵌段酰胺PEBA Thermoplastic elastomer polyether 聚酯热塑弹性体PEEK Polyetheretherketone 聚醚醚酮PEI Poly(etherimide) 聚醚酰亚胺PEK Polyether ketone 聚醚酮PEO Poly(ethylene oxide) 聚环氧乙烷PES Poly(ether sulfone) 聚醚砜PET Poly(ethylene terephthalate) 聚对苯二甲酸乙二酯PETG Poly(ethylene terephthalate) glycol 二醇类改性PET PEUR Poly(ether urethane) 聚醚型聚氨酯PF Phenol-formaldehyde resin 酚醛树脂PFA Perfluoro(alkoxy alkane) 全氟烷氧基树脂PFF Phenol-furfural resin 酚呋喃树脂PI Polyimide 聚酰亚胺PIB Polyisobutylene 聚异丁烯PISU Polyimidesulfone 聚酰亚胺砜PMCA Poly(methyl-alpha-chloroacrylate) 聚α-氯代丙烯酸甲酯PMMA Poly(methyl methacrylate) 聚甲基丙烯酸甲酯PMP Poly(4-methylpentene-1) 聚4-甲基戊烯-1PMS Poly(alpha-methylstyrene) 聚α-甲基苯乙烯POM Polyoxymethylene, polyacetal 聚甲醛PP Polypropylene 聚丙烯PPA Polyphthalamide 聚邻苯二甲酰胺PPE Poly(phenylene ether) 聚苯醚PPO Poly(phenylene oxide) deprecated 聚苯醚PPOX Poly(propylene oxide) 聚环氧（丙）烷PPS Poly(phenylene sulfide) 聚苯硫醚PPSU Poly(phenylene sulfone) 聚苯砜PS Polystyrene 聚苯乙烯PSU Polysulfone 聚砜PTFE Polytetrafluoroethylene 聚四氟乙烯PUR Polyurethane 聚氨酯PVAC Poly(vinyl acetate) 聚醋酸乙烯PVAL Poly(vinyl alcohol) 聚乙烯醇PVB Poly(vinyl butyral) 聚乙烯醇缩丁醛PVC Poly(vinyl chloride) 聚氯乙烯PVCA Poly(vinyl chloride-acetate) 聚氯乙烯醋酸乙烯酯PVCC chlorinated poly(vinyl chloride)(*CPVC) 氯化聚氯乙烯PVI poly(vinyl isobutyl ether) 聚(乙烯基异丁基醚)PVM poly(vinyl chloride vinyl methyl ether) 聚(氯乙烯-甲基乙烯基醚)RAM restricted area molding 窄面模塑RF resorcinol-formaldehyde resin 甲苯二酚-甲醛树脂RIM reaction injection molding 反应注射模塑RP reinforced plastics 增强塑料RRIM reinforced reaction injection molding 增强反应注射模塑RTP reinforced thermoplastics 增强热塑性塑料S/AN styrene-acryonitrile copolymer 苯乙烯-丙烯腈共聚物SBS styrene-butadiene block copolymer 苯乙烯-丁二烯嵌段共聚物SI silicone 聚硅氧烷SMC sheet molding compound 片状模塑料S/MS styrene-α-methylstyrene copolymer 苯乙烯-α-甲基苯乙烯共聚物TMC thick molding compound 厚片模塑料TPE thermoplastic elastomer 热塑性弹性体TPS toughened polystyrene 韧性聚苯乙烯TPU thermoplastic urethanes 热塑性聚氨酯TPX ploymethylpentene 聚-4-甲基-1戊烯VG/E vinylchloride-ethylene copolymer 聚乙烯-乙烯共聚物VC/E/MA vinylchloride-ethylene-methylacrylate copolymer 聚乙烯-乙烯-丙烯酸甲酯共聚物VC/E/VCA vinylchloride-ethylene-vinylacetate copolymer 氯乙烯-乙烯-醋酸乙烯酯共聚物PVDC Poly(vinylidene chloride) 聚（偏二氯乙烯）PVDF Poly(vinylidene fluoride) 聚（偏二氟乙烯）PVF Poly(vinyl fluoride) 聚氟乙烯PVFM Poly(vinyl formal) 聚乙烯醇缩甲醛PVK Polyvinylcarbazole 聚乙烯咔唑PVP Polyvinylpyrrolidone 聚乙烯吡咯烷酮S/MA Styrene-maleic anhydride plastic 苯乙烯-马来酐塑料SAN Styrene-acrylonitrile plastic 苯乙烯-丙烯腈塑料SB Styrene-butadiene plastic 苯乙烯-丁二烯塑料Si Silicone plastics 有机硅塑料SMS Styrene/alpha-methylstyrene plastic 苯乙烯-α-甲基苯乙烯塑料SP Saturated polyester plastic 饱和聚酯塑料SRP Styrene-rubber plastics 聚苯乙烯橡胶改性塑料TEEE Thermoplastic Elastomer,Ether-Ester 醚酯型热塑弹性体TEO Thermoplastic Elastomer, Olefinic 聚烯烃热塑弹性体TES Thermoplastic Elastomer, Styrenic 苯乙烯热塑性弹性体TPEL Thermoplastic elastomer 热塑(性)弹性体TPES Thermoplastic polyester 热塑性聚酯TPUR Thermoplastic polyurethane 热塑性聚氨酯TSUR Thermoset polyurethane 热固聚氨酯UF Urea-formaldehyde resin 脲甲醛树脂UHMWPE Ultra-high molecular weight PE 超高分子量聚乙烯UP Unsaturated polyester 不饱和聚酯VCE Vinyl chloride-ethylene resin 氯乙烯/乙烯树脂VCEV Vinyl chloride-ethylene-vinyl 氯乙烯/乙烯/醋酸乙烯共聚物VCMA Vinyl chloride-methyl acrylate 氯乙烯/丙烯酸甲酯共聚物VCMMA Vinyl chloride-methylmethacrylate 氯乙烯/甲基丙烯酸甲酯共聚物VCOA Vinyl chloride-octyl acrylate resin 氯乙烯/丙烯酸辛酯树脂VCVAC Vinyl chloride-vinyl acetate resin 氯乙烯/醋酸乙烯树脂VCVDC Vinyl chloride-vinylidene chloride 氯乙烯/偏氯乙烯共聚物。
(完整版)塑料简称中英文对照汇总
PVC--聚氯乙烯PE--聚乙烯PPR--无规（随机）聚丙烯PVDF--聚偏二氟乙烯详细管材如下:EV A--乙烯－醋酸乙烯聚物PET 聚对苯二甲酸乙二酯poly(ethylene terephthalate) 01PE-HD 高密度聚乙烯polyethylene, high density 02PVC 聚氯乙烯poly(vinyl chloride) 03PE-LD 低密度聚乙烯polyethylene,low density 04PP 聚丙烯polypropylene 05PS 聚苯乙烯polystyrene 06ABS 丙烯腈－丁二烯－苯乙烯塑料acrylonitrile-butadiene-styrene plastic 07PA 聚酰胺polyamide 08PAN 聚丙烯腈polyacrylonitrile 09PC 聚碳酸酯polycarbonate 10PBT 聚对苯二甲酸丁二酯poly(butylene terephthalate) 11PE-LLD 线性低密度聚乙烯polyethylene,linear low density 12PE-MD 中密度聚乙烯polyethylene,medium density 13PE-UHMW 超高分子量聚乙烯polyethylene,ultra high molecular weight 14 PUR 聚氨酯polyurethane 15PMMA 聚甲基丙烯酸甲酯poly(methyl methacrylate) 16PV AL 聚乙烯醇poly(vinyl alcohol) 17PVC-C 氯化聚氯乙烯poly(vinyl chloride),chlorinated 18PVC-U 未增塑聚氯乙烯poly(vinyl chloride),unplasticized 19PVDC 聚偏二氯乙烯poly(vinylidene chloride) 20PVDF 聚偏二氟乙烯poly(vinylidene fluoride) 21PVF 聚氟乙烯poly(vinyl fluoride) 22UP 不饱和聚酯树脂unsaturated polyester resin 23UF 脲－甲醛树脂urea-formaldehyderesin 24CA 乙酸纤维素cellulose acetate 25PEEK 聚醚醚酮polyetheretherketone 26PEUR 聚醚型聚氨酯polyetherurethane 27PF 酚醛树脂phenol-formaldehyde resin 28PI 聚酰亚胺polyimide 29PHBV 聚羟基丁酸酯戊酸酯poly-(hydroxybutyrate-co-hydroxyvalerate 30 PK 聚酮polyketone 30PTFE 聚四氟乙烯poly tetrafluoroethylene 31POM 聚氧亚甲基；聚甲醛；聚缩醛polyoxymethylene;polyacetal;polyformaldehyde 32PLA 聚乳酸polylactic acid or polylactide 33PCL 聚已内酯polycaprolactone 34PPDO 聚对二氧环己酮35PPC 二氧化碳共聚合物carbon dioxide copolymer 36PBS 聚丁二酸丁二醇酯Polybuthylenesuccinate 37PHA 聚羟基脂肪酸酯polyhydroxyalkanoic or polyhydroxyalkanoates 38 PHB 聚-3-羟基丁酸polyhydroxybutyric acid or polyhydroxybutyrate 39 PGA 聚乙交酯poly(glycolic acid) 40PEC PolyEster Carbonate or Poly(Butylene Succinate/Carbonate) 41PES Poly(Ethylene Succinate) 42PTMAT Poly(TetraMethylene Adipate/Terephthalate) 43PBA T Poly(Butylene Adipate/Terephthalate) 44AB 丙烯腈－丁二烯塑料acrylonitrile-butadiene plastic 45ABAK 丙烯腈－丁二烯－丙烯酸酯塑料acrylonitrile-butadiene-acrylate plastic 46ACS 丙烯腈-氯化聚乙烯-苯乙烯塑料acrylonitrile-chlorinated polyethylene-styrene 47AEPDS 丙烯腈－（乙烯－丙烯－二烯）－苯乙烯塑料acrylonitrile-(ethylene-propylene-diene)-styrene plastic 48AMMA 丙烯腈－甲基丙烯酸甲酯塑料acrylonitrile-methyl methacryate plastic 49ASA 丙烯腈-苯乙烯-丙烯酸酯塑料acrylonitrile-stytene-acrylate plastic 50CAB 乙酸丁酸纤维素cellulose acetate butyrate 51CAP 乙酸丙酸纤维素cellulose acetate propionate 52CEF 甲醛纤维素cellulose formaldehyde 53CF 甲酚－甲醛树脂cresol-formaldehyde resin 54CMC 羧甲基纤维素carboxymethyl cellulose 55CN 硝酸纤维素cellulose nitrate 56COC 环烯烃共聚物cycloolefin copolymer 57CP 丙酸纤维素cellulose propionate 58CTA 三乙酸纤维素cellulose triacetate 59E/P 乙烯－丙烯塑料ethylene-propylene plastic 60EAA 乙烯－丙烯酸塑料ethylene-acrylic acid plastic 61EBAK 乙烯－丙烯酸丁酯塑料ethylene-butyl acrylate plastic 62EC 乙基纤维素ethyl cellulose 63EEAK 乙烯－丙烯酸乙酯塑料ethylene-ethyl acrylate plastic 64EMA 乙烯－甲基丙烯酸塑料ethylene-methacrylic acid plastic 65EP 环氧；环氧树脂或塑料epoxide;epoxy resin or plastic 66ETFE 乙烯－四氟乙烯塑料e thylene-tetrafluoroethylene plastic 67EV AC 乙烯－乙酸乙烯酯塑料ethylene-vinyl acetate plastic 68EVOH 乙烯－乙烯醇塑料ethylene-vinyl alcohol plastic 69FEP 全氟（乙烯－丙烯）塑料perfluoro(ethylene-propylene)plastic 70 FF 呋喃－甲醛树脂furan-formaldehyde resin 71LCP 液晶聚合物liquid-crystal polymer 72MABS 甲基丙烯酸甲酯－丙烯腈－丁二烯－苯乙烯塑料methyl methacrylate-acrylonitrile-butadiene-styrene plastic 73MBS 甲基丙烯酸甲酯－丁二烯－苯乙烯塑料methyl methacrylate-butadiene-styrene plastic 74MC 甲基纤维素methyl cellulose 75MF 三聚氰胺－甲醛树脂melamine-formaldehyde resin 76MP 三聚氰胺－酚醛树脂melamine-phenol resin 77MSAN α－甲基苯乙烯－丙烯腈塑料α-methylstyrene-acrylonitrile plastic 78PAA 聚丙烯酸poly(acrylic acid) 79PAEK 聚芳醚酮polyaryletherketone 80PAI 聚酰胺（酰）亚胺polyamidimide 81PAK 聚丙烯酸酯polyarylate 82PAR 聚芳酯polyarylate 83PARA 聚芳酰胺poly(aryl amide) 84PB 聚丁烯polybutene 85PBAK 聚丙烯酸丁酯poly(butyl acrylate) 86PBD 1,2－聚丁二烯1,2-polybutadiene 87PBN 聚萘二甲酸丁二酯poly(butylene naphthalate) 88PCCE 亚环己基-二亚甲基-环已基二羧酸酯poly(cyclohexylene dimethylene cyclohexanedicar- boxylate) 89PCT 聚（对苯二甲酸亚环已基-二亚甲酯）poly(cyclohexylene dimethylene terephthalate) 90PCTFE 聚三氟氯乙烯polychlorotrifluoroethylene 91PDAP 聚邻苯二甲酸二烯丙酯poly(diallyl phthalate) 92PDCPD 聚二环戊二烯polydicyclopentadiene 93PEC 聚酯碳酸酯polyestercarbonate 94PE-C 氯化聚乙烯polyethylene,chlorinated 95PEEST 聚醚酯polyetherester 96PEI 聚醚（酰）亚胺polyetherimide 97PEK 聚醚酮polyetherketone 98PEN 聚萘二甲酸乙二酯poly(ethylene naphthalate) 99PEOX 聚氧化乙烯poly(ethylene oxide) 100PESTUR 聚酯型聚氨酯polyesterurethane 101PESU 聚醚砜polyethersulfone 102PE-VLD 极低密度聚乙烯polyethylene,very low density 103PFA 全氟烷氧基烷树脂perfluoro alkoxyl alkane resin 104PIB 聚异丁烯polyisobutylene 105PIR 聚异氰脲酸酯polyisocyanurate 106PMI 聚甲基丙烯酰亚胺polymethacrylimide 107PMMI 聚N－甲基甲基丙烯酰亚胺poly-N-methylmethacrylimide 108 PMP 聚－4－甲基戊烯－1poly-4-methylpentene-1 109PMS 聚－α－甲基苯乙烯poly-α-methylstyrene 110PPE 聚苯醚poly(phenylene ether) 111PP-E 可发性聚丙烯polypropylene,expandable 112PP-HI 高抗冲聚丙烯polypropylene,high impact 113PPOX 聚氧化丙烯poly(propylene oxide) 114PPS 聚苯硫醚poly(phenylene sulfide) 115PPSU 聚苯砜poly(phenylene sulfone) 116PS-E 可发聚苯乙烯polystyrene,expandable 117PS-HI 高抗冲聚苯乙烯polystyrene,high impact 118PSU 聚砜polysulfone 119PTT 聚对苯二甲酸丙二酯poly(trimethylene terephthalate) 120PV AC 聚乙酸乙烯酯poly(vinyl acetate) 121PVB 聚乙烯醇缩丁醛poly(vinyl butyral) 122PVFM 聚乙烯醇缩甲醛poly(vinyl formal) 123PVK 聚-N-乙烯基咔唑poly-N-vinylcarbazole 124PVP 聚-N-乙烯基吡咯烷酮poly-N-vinylpyrrolidone 125SAN 苯乙烯一丙烯腈塑料styrene-acrylonitrile plastic 126SB 苯乙烯-丁二烯塑料styrene-butadiene plastic 127SI 有机硅塑料silicone plastic 128SMAH 苯乙烯－顺丁烯二酸酐塑料styrene-maleic anhydride plastic 129SMS 苯乙烯－α－甲基苯乙烯塑料styrene-α-methylstyrene plastic 130VCE 氯乙烯－乙烯塑料vinyl chloride-ethylene plastic 131VCEMAK 氯乙烯－乙烯－丙烯酸甲酯塑料vinyl chloride-ethylene-methyl acrylate plastic 132VCEV AC 氯乙烯－乙烯－丙烯酸乙酯塑料vinyl chloride-ethylene-vinyl acrylate plastic 133VCMAK 氯乙烯－丙烯酸甲酯塑料vinyl chloride-methyl acrylate plastic 134 VCMMA 氯乙烯－甲基丙烯酸甲酯塑料vinyl chloride-methyl methacrylate plastic 135VCOAK 氯乙烯－丙烯酸辛酯塑料vinyl chloride-octyl acrylate plastic 136 VCV AC 氯乙烯－乙酸乙烯酯塑料vinyl chloride-vinyl acetate plastic 137 VCVDC 氯乙烯－偏二氯乙烯塑料vinylchloride-vinylidene chloride plastic 138 VE 乙烯基酯树脂vinyl ester resin 139PE 聚乙烯polyethylene聚乙烯——PE聚丙烯——PP聚丁烯——PB聚氯乙稀——PVC耐热聚乙稀——PE-RT硬聚氯乙稀（增强聚氯乙烯）——PVC-U（UPVC）高密度聚乙烯——HDPE无规共聚聚丙烯——PP-R玻纤增强聚丙烯——FRPP低密度聚乙烯——LDPE聚甲基丙烯酸甲酯——PMMA聚四氟乙烯——PTFE（F4）三元乙丙橡胶——EPDM多孔聚苯乙烯——XPS腈基丁二烯橡胶（丁腈橡胶）——NBR耐冲击性聚苯乙烯——HIP聚氟乙烯——PVF纳米复合三型聚丙烯——NFPP-R塑料光纤——POF丙稀腈－丁二烯－苯乙烯——ABS氯化聚醚——CPS氯化聚醚丁腈（粉末丁腈橡胶）——PNBR 聚全氟乙丙稀（氟化乙丙稀）——FEP均聚聚丙烯——PPH聚偏氟乙烯——PVDF共聚酰胺（尼龙）——PA增强聚丙烯——RPP共聚酯——PES高分子聚丙烯酰胺——PAM增强氯化聚氯乙稀——CPVC嵌段共聚聚丙烯——PPB聚苯乙烯——PS交联聚乙烯——PEX聚烯烃——PO三氟氯乙烯——CTFE全氟代甲基醚——PMVE全氟代乙基醚——PEVE全氟代丙基醚——PPVE全氟代辛基醚——POVE全氟代烷氧基——PFA聚对苯二甲酸乙二醇酯——PET定向聚丙烯——OPP流延聚丙烯——CPP共聚甲醛（聚氧甲烯、缩醛）——POM茂金属线型低密度聚乙烯——MLLDPE丙烯酸酯橡胶——ACM氯丁胶——CR氟橡胶——FPM端缩基丁腈液体橡胶——HTBN硅胶——MQ氯磺化聚乙烯橡胶——CSM丁钠橡胶——S-BR天然橡胶——NR。
塑料模具行业专业术语中英文对照
塑料模具中英语对照塑料模具英语入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate细水口：pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate 圆形流道：round(full/half runner流道电脑分析：mold flow analysis 流道平衡:runner balance热嘴：hot sprue 热流道板：hot manifold发热管：cartridge heater 探针: thermocouples插头：connector plug 插座：connector socket密封/封料：seal三、运水：water line 喉塞：line lpug喉管：tube塑胶管：plastic tube 快速接头：jiffy quick connectorplug/socker四、模具零件：mold components三板模：3-plate mold 二板模：2-plate mold边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing中托司：shoulder guide bushing 中托边L：guide pin顶针板：ejector retainner plate 托板：support plate螺丝：screw 管钉：dowel pin开模槽：ply bar scot 内模管位：core/cavity inter-lock 顶针：ejector pin 司筒：ejector sleeve司筒针：ejector pin 推板：stripper plate缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter模胚（架）：mold base 上内模：cavity insert下内模：core insert 行位（滑块）：slide镶件：insert 压座/斜鸡：wedge耐磨板/油板：wedge wear plate 压条：plate撑头: support pillar 唧嘴：sprue bushing挡板：stop plate 定位圈：locating ring锁扣：latch 扣鸡：parting lock set推杆：push bar 栓打螺丝：S.H.S.B顶板：eracuretun 活动臂：lever arm分流锥：spure sperader 水口司:bush垃圾钉：stop pin 隔片：buffle弹弓柱：spring rod 弹弓:die spring中托司：ejector guide bush 中托边：ejector guide pin镶针：pin 销子：dowel pin波子弹弓：ball catch模具成形不良用语英汉对照aberration 色差atomization ?化bank mark ?料纹bite 咬入blacking hole 涂料孔(铸疵) blacking scab 涂料疤blister 起泡blooming 起霜low hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折叠straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹各式模具分类用语英汉对照landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模各种模具常用成形方式英汉对照accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming ?泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模机械类常用英语：冲压模具-零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块机械类常用英语：冲压模具-模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模) feature die公母模female die母模(凹模) upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板冲压模具-冲压名称类英汉对照plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量模具工程常用词汇英汉对照——3high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程常用词汇英汉对照——2stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁模具工程常用词汇英汉对照die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physical invetory second count 复盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accounting department for reference会计部存查end-user/using unit(department)使用单位summary of year-end physical inventory bills 年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory list will be sent to accountingdepartment together (Those of NHK will be sent to financialdepartment)本表请与盘点清册一起送会计部－(NHK 厂区送财会部)Application status records of year-end physical inventory List andphysical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门模具钢材及零件英语模具钢材alloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 硅钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑料覆面钢板零件英语punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location 定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mm L=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣sprue lock pin料头钩销(拉料杆)加为好友只看该作者塑件模具相关英文——10eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Runner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣塑件模具相关英文——9compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具encapsulation molding低压封装成型、射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕模具相关英语——8stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模) feature die公母模female die母模(凹模) upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块模具相关英语——7emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱模具相关英语——6drill钻boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys 花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边模具相关英语——5spare parts=buffer备品coordinate坐标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave 凹convex凸short射料不足nick缺口speck瑕疪shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨模具相关英语——4baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条形码flow chart流程窗体assembly组装stamping冲压molding成型模具相关英语——3difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板模具相关英语——2steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model机钟work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量模具相关英语——1padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder活页夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physical invetory second count 复盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accounting department for reference会计部存查end-user/using unit(department)使用单位summary of year-end physical inventory bills 年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory list will be sent to accounting departmenttogether (Those of NHK will be sent to financial department)本表请与盘点清册一起送会计部－(NHK 厂区送财会部)Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品incoming material to be inspected进货待验description品名101个热处理常用英文词汇1. indication 缺陷2. test specimen 试样3. bar 棒材4. stock 原料5. billet 方钢，钢方坯6. bloom 钢坯,钢锭7. section 型材8. steel ingot 钢锭9. blank 坯料，半成品10. cast steel 铸钢11. nodular cast iron 球墨铸铁12. ductile cast iron 球墨铸铁13. bronze 青铜14. brass 黄铜15. copper 合金16. stainless steel不锈钢17. decarburization 脱碳18. scale 氧化皮19. anneal 退火20. process anneal 进行退火21. quenching 淬火22. normalizing 正火23. Charpy impact text 夏比冲击试验24. fatigue 疲劳25. tensile testing 拉伸试验26. solution 固溶处理27. aging 时效处理28. Vickers hardness维氏硬度29. Rockwell hardness 洛氏硬度30. Brinell hardness 布氏硬度31. hardness tester硬度计32. descale 除污，除氧化皮等33. ferrite 铁素体34. austenite 奥氏体35. martensite马氏体36. cementite 渗碳体37. iron carbide 渗碳体38. solid solution 固溶体39. sorbite 索氏体40. bainite 贝氏体41. pearlite 珠光体42. nodular fine pearlite/ troostite屈氏体43. black oxide coating 发黑44. grain 晶粒45. chromium 铬46. cadmium 镉47. tungsten 钨48. molybdenum 钼49. manganese 锰50. vanadium 钒51. molybdenum 钼52. silicon 硅53. sulfer/sulphur 硫54. phosphor/ phosphorus 磷55. nitrided 氮化的56. case hardening 表面硬化，表面淬硬57. air cooling 空冷58. furnace cooling 炉冷59. oil cooling 油冷60. electrocladding /plating 电镀61. brittleness 脆性62. strength 强度63. rigidity 刚性,刚度64. creep 蠕变65. deflection 挠度66. elongation 延伸率67. yield strength 屈服强度68. elastoplasticity 弹塑性69. metallographic structure 金相组织70. metallographic test 金相试验71. carbon content 含碳量72. induction hardening 感应淬火73. impedance matching 感应淬火74. hardening and tempering 调质75. crack 裂纹76. shrinkage 缩孔，疏松77. forging 锻（件）78. casting 铸（件）79. rolling 轧（件）80. drawing 拉（件）81. shot blasting 喷丸（处理）82. grit blasting 喷钢砂（处理）83. sand blasting 喷砂（处理）84. carburizing 渗碳85. nitriding 渗氮86. ageing/aging 时效87. grain size 晶粒度88. pore 气孔89. sonim 夹砂90. cinder inclusion 夹渣91. lattice晶格92. abrasion/abrasive/rub/wear/wearing resistance (property) 耐磨性93. spectrum analysis光谱分析94. heat/thermal treatment 热处理95. inclusion 夹杂物96. segregation 偏析97. picking 酸洗，酸浸98. residual stress 残余应力99. remaining stress 残余应力100. relaxation of residual stress 消除残余应力101. stress relief 应力释放模具相关英语(5)semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模) feature die公母模female die母模(凹模) upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件) deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块模具相关英语(4)coordinate坐标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave 凹convex凸short射料不足nick缺口speck瑕疪shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill钻boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆模具相关英语(3)difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销。
塑胶行业英文专业用语
塑胶行业英语Surface Appearance 外观Glossiness/gloss finish 光洁度Matt finish/matt surface 毛面Glass fiber rich surface/glass emergence on the surface 玻纤外露Blooming/surface blooming 表面析出White patches on surface 表面白斑Silver marks/silver streak 银纹Splay mark 水纹Flow mark 流纹Weld line 溶结纹Brittle/brittleness 脆Bubbles/trapped gas 气泡Void 孔Burn marks 烧伤FR failed 阻燃不合格Flame rating V-2 阻燃V-2Poor dispersion 分散不好FR/PTFE…agglomerates etc 阻燃剂/PTFE…结块Pellet porous 粒子不密、蜜蜂窝Low impact/tensile ect 物理性能低High flow/filler content etc流动性、填充…过高Longs/fines/doubles 长粒、碎屑、连粒Poor cut 粒形不好Bristle/voids 表面有小气泡、孔Glass bundles 玻纤结团Product was rejected due to产品不能接受因为…High moisture level 高水分Warpage/warped翘曲Shrinkage/shrink 收缩Sink marks 缩影Short shot/short molding打不满Distortion 变形Over dimension 尺寸过大Under dimension 尺寸过小Flashing 飞边Discoloration 变色Off color 颜色差异Flow rate 流动率Viscous 粘High flow 高流动Low flow 低流动Sticky 粘Mold release 脱模Antioxidant 抗氧剂Flame retardant agent 阻燃剂Heat stabilizer 热稳定剂Chopped glass fiber 短切玻纤Roving glass fiber 粗纱、长玻纤Glass beads 玻璃微珠Milled fiber 碾磨纤Molybdenum disulfide/moly/MoS2 二硫化钼Colorant 着色剂Pigment 颜料Dye 染料Accepted product specification 接受产品规格Approved our product 认可我们的产品Re-set spec 重新定标准Add in extra…添加多一点…Reduced … content 减少…含量Dropped/reduced … by X%减少…含量…x%Confirmed color standard 确认颜色标准Approved color standard 认可颜色标准Re-confirmed color standard 重新确认颜色标准Qualified our product 认可我们的产品Undergoing heat aging test 在做热老化实验Product is under testing 产品在测试当中Received first order 接了第一个订单Expected to finish by…预计在…完成Expected order is xMT 预计订量…吨Estimated annual/monthly consumption 预计年、月用量。
塑料类专业术语
塑料类专业术语ABS塑料英文名称:Acrylonitrile Butadiene Styrene比重:1.05克/立方厘米,适于制作一般机械零件,减磨耐磨零件,传动零件和电讯零件.具有以下性能：1、综合性能较好,冲击强度较高,化学稳定性,电性能良好.2、与372有机玻璃的熔接性良好,制成双色塑件,且可表面镀铬,喷漆处理.3、有高抗冲、高耐热、阻燃、增强、透明等级别。
4、流动性比HIPS差一点，比PMMA、PC等好，柔韧性好。
PE塑料(聚乙烯)英文名称:Polyethylene比重:0.94-0.96克/立方厘米成型收缩率:1.5-3.6%成型温度：140-220℃干燥条件：---物料性能耐腐蚀性,电绝缘性(尤其高频绝缘性)优良,可以氯化,辐照改性,可用玻璃纤维增强.低压聚乙烯的熔点,刚性,硬度和强度较高,吸水性小,有良好的电性能和耐辐射性;高压聚乙烯的柔软性,伸长率,冲击强度和渗透性较好;超高分子量聚乙烯冲击强度高,耐疲劳,耐磨.低压聚乙烯适于制作耐腐蚀零件和绝缘零件;高压聚乙烯适于制作薄膜等;超高分子量聚乙烯适于制作减震,耐磨及传动零件.成型性能1.结晶料,吸湿小,不须充分干燥,流动性极好流动性对压力敏感,成型时宜用高压注射,料温均匀,填充速度快,保压充分.不宜用直接浇口,以防收缩不均,内应力增大.注意选择浇口位置,防止产生缩孔和变形.2.收缩范围和收缩值大,方向性明显,易变形翘曲.冷却速度宜慢,模具设冷料穴,并有冷却系统.3.加热时间不宜过长,否则会发生分解,灼伤.4.软质塑件有较浅的侧凹槽时,可强行脱模.5.可能发生融体破裂,不宜与有机溶剂接触,以防开裂.PP塑料(聚丙烯)英文名称:Polypropylene比重:0.9-0.91克/立方厘米成型收缩率:1.0-2.5%成型温度：160-220℃干燥条件：---物料性能密度小,强度刚度,硬度耐热性均优于低压聚乙烯,可在100度左右使用.具有良好的电性能和高频绝缘性不受湿度影响,但低温时变脆,不耐模易老化.适于制作一般机械零件,耐腐蚀零件和绝缘零件成型性能1.结晶料,吸湿性小,易发生融体破裂,长期与热金属接触易分解.2.流动性好,但收缩范围及收缩值大,易发生缩孔.凹痕,变形.3.冷却速度快,浇注系统及冷却系统应缓慢散热,并注意控制成型温度.料温低方向方向性明显.低温高压时尤其明显,模具温度低于50度时,塑件不光滑,易产生熔接不良,留痕,90度以上易发生翘曲变形4.塑料壁厚须均匀,避免缺胶,尖角,以防应力集中.聚氯乙烯采用聚苯乙烯标准物，以THF（四氢呋喃）为流动相（注意您的柱子要能用于THF），示差折光检测器，用普适标定法测定PVC的分子量及其分布。
塑料行业常用英汉名词对照表
AAcrylonitrile butadiene styrene-(ABS)甲烯腈丁二烯苯乙烯Basic catalysts碱性接触剂法Acstals 缩醛树脂Benzene 苯Aceto-acetanilide乙硫基乙硫苯胺Beryllia氧化铍Aceto-butyrate 乙硫基丁酸脂Bisdien polymer双二烯聚合体Acetone 丙酮Bis-phenoldioxy(ethyl ether)双酚二氧化(二乙醚)Acetylene 乙炔Blowing method 吹塑导气法Acid catalysts酸性接触剂法Blow molding 吹入模型法Acrylamide Polymer 丙烯基硫胺聚合物Butadiene 丁二烯Acrylic acid 丙烯酸Butane 丁烷Acrylic ester 丙烯酸脂Butanal丁醇Acrylic PVC 丙烯酸Butyl phenol丁酚Acrylonitrile 丙烯腈Activating活化工程Aerovac process 气相真空法Calcium 钙Air-assist forming 空气辅助成型法Calendering 轮压加工Aldehydes 甲醛Caprolactam 己酸内硫胺Aliphatic脂肪族的Carbonate碳酸盐Aliphatic hydrocarvons 脂肪族碳氢化合物Carboxy polymethylene 羰聚甲烯Alkyds醇酸树脂Casein 酪酸 酪素Alkyl Ketene Dimer 烷基乙烯酮二聚物Casting铸塑法Allyl resin丙烯树脂Cashew oil resin 漆油树脂Alpha cellulose 纤维素Cashew oil phenolic 漆树油酚甲醛树脂Amyl acetate 醋酸戍酯Cellophane 赛璐玢Anitimony oxide 氧化亚锑Cllulose纤维素Antioxidants 抗氧剂Cllulose acetate醋酸纤维Applied stress 应用力Cllulose acetate butyrate 醋酸酪酸纤维Arc resistance 抗电弧性Cllulose nitrate 硝酸纤维Artificial dielectric 人造诱电体片Cllulose triacetate 三醋酸纤维Asbestos 石棉Cllulose propionate 丙酸纤维Atactic甲基族位置Centrifugal casting 离心力铸塑法Autoclave molding 压热气模造法Ceramoplastics 陶类塑料Automatic molding 自动化模造法Chlorinated paraffin 氯化石蜡Azodicarbonamide偶氮甲光胺Chlorinate polyether 氯化聚合醚Chloromalaic acid 氯化代马来酸Chrysotile 温石棉Cold molding冷模型法Bakelite电木Cold plunger molding 缩合树脂模造法Baking shrinkage烤缩Compression molding压缩模型法塑胶行业常用(英汉名词对照)BCcondensation resin 縮合樹脂ethylene oxide氧化乙烯contact molding接觸模型法ethylene vinyl acetate 聚乙烯醋酸乙烯酯continuous tube blow molding 連續吹管模造法expanded plastics 膨脹塑膠copolymer 共聚物expanded styrene 膨脹苯乙烯creep 變形試驗expansion agent 膨脹劑cresols 甲酚extrusion擠壓模型法crocidoite 青石棉extrusion blow molding擠吹模型法cumene 異丙苯cure硬化curtain coating 流水式塗抹塑料法fatty acid脂肪酸cyanamide氰胺fiberglass reinforced玻璃纖維硬化cyanoguanidine 氰呱finishing成形品修整cyclo pentadiene環戊二烯flash mold毛邊模fluidized bed coating流動浸積flurocarbon rensins氟素樹脂dehydrogenation除氫手續fluorinated ethylene propylene 氟素乙烯丙烯density密度force above sheet片上加壓法depolymerize脫聚合化formaldehyde甲醛diallyl phthalate酜酸二丙烯酯furanes呋喃樹脂dichloro-difluoromethane 二氯二氟甲烷furfural呋醛diekectric preheating誘電預熱法diethyl phosphate磷酸二乙酯dietheyl sulphate硫酸乙烯dimethylaniline二甲苯胺glass-bonded mica玻璃雲石dip coating浸積塗抹塑料法glass resins 玻璃樹脂disopropyl fumarate反丁烯二酸二異丙酯graphite 石墨drape vacuum forming摺疊真空成型法guanamine呱胺halogenated鹵代增塑劑emulsion乳化劑hexamethy lene-tetramine 環六次甲基四胺engelit foaming process 起泡法heisler process 單旋模造法epoxics 依博士樹脂homopolymer 均聚物epoxide 環氧化物hydrate 水合物epoxy 環氧化物hydrocarbon 碳氫化合物ester 脂hydrochloric氫氯化合物ether醚hydrochloric acid 鹽酸ethyl benzene 乙苯hydrofluoric 氫氟ethyl chliride 氯乙烷hydrogenation氫化ethylene乙烯hydroxy ethyl cellulose羟乙基纖維ethylene glycol乙二醇inflation laminating 吹氣疊合模型法olefin烯族烃injection blow molding 注射吹氣模造法ortho-chlorstyrol正氯化苯乙苯injection molding 射出模型法inorganic pigment 無機顏料isocyanate 異氰酸酯pentaerythritol 五丁四醇isopropylidene異亞丙烯pentane戊烷GDFEHIOPperoxides 過氧化物phenol酚jet molding射膠法phenol-formaldehyde 酚甲醛phenol furfural酚呋喃醛phenolic molding powder 酚醛膠粉ketone酮phenolics酚樹脂knife coating刀塗裝法phenol aldehyde 酚醛樹脂phenyl苯基phenyl-titanate 鈦酸苯脂lactam 內硫胺phosphate ester磷酸酯laminating 積層模型法phosphate plasticizer 磷酸增塑劑lignum vitac癒創樹phosphor bronze 磷青銅plasticate 塑煉plasticity 塑形性magnesium鎂plasticization增塑mechanized molding機械化模造法plasticizer extender 輔增塑劑mer麻plastic propellant 塑性推進劑methacresol甲基甲酚plastify 塑化methacrylate alphamethyl s甲基苯乙烯plating塑膠鍍金methacrylic甲機丙烯酸plastisol molding 塑膠液模造法methane甲烷plug& ring forming行槌與環成形法melamine三聚氰胺plunger preplastication 行程預塑式methyl甲基poly butylene 聚丁烯methyl methacrylate丙烯酸甲脂poly blends 聚合混合menthyl pentene甲基丙乙烯polyamide 聚硫胺樹脂molding compound機型塑料polycarbonate聚碳酸脂monofluoro單氟polychlorotrifluoroethylenc 聚氯已烯三氟monomer單量體polyester多元脂polyesterimide 多元脂硫亞胺polyethers 多元醚neodymium氧化胺polyethylene聚乙烯（软膠）neoprene 氯丁橡膠polyethylene oxide 聚環氧乙烷nichrom 镍鉻polyfusion 聚融合作用nitrile腈polyimide 聚酰亞胺nitrocellulose 硝化纖維polymethylene聚甲烯nylons尼龍polymethyl methacrylate 聚合甲基丙烯酸甲脂polymethyl pentene 聚甲基戊烯polymisobutylene聚異丁烯Polyolefins 聚烯族烃Spray forming 喷射模型法Polyparaxylene聚对位二甲苯Stean forming蒸气模型法Polyphenylene oxide 聚二氧苯Static power molding process 静力粉剂模造法Polyropylene 聚丙烯Straight vacuum forming 直线真空模造法Polystyrene 聚丙乙烯Styrene苯乙烯Polysulphone聚風苯乙烯丙烯腈Polytetraflouroethylene 聚四氟化乙烯共聚物PolyurethaneStyrene butadiene 苯乙烯丁二烯Polyvinyl acetate 聚醋酸乙烯Styrene copolymer 乙烯共聚合物Polyvinyl alcohol 聚乙烯醇Styrene polymer乙烯聚合物Polyvinyl butyral聚乙烯縮丁醛TStyrene-acrylonitrile copolymerNJKLMPolyvinyl chloride-PVC 聚氯化乙烯樹脂Terephthalic acid对苯二甲酸Polyvinylidene chloride 聚偏二氯乙烯Tertiary amines叔胺Post forming後成形Tetra chlorophthalic 四氯酸粉Power molding粉狀塑料模型法Tetraethyl lead 四乙铅Preheating method預熱方法Thermo forming 热模型法Pressure & thermo forming壓力及熱力成型法Thermoplastic 热可塑性塑料Pressure forming壓力成型法Thermosetting 热硬化性塑料Pressure sizing壓力袋模造法Titanium dioxide 钛粉Propane名烷Toluene甲苯Pyroxylin焦棉 火棉Transfer molding 转移模型法Tricresyl phosphate亚磷酸三个甲Quartz石英 二氧化矽結晶Urea尿素Urea formaldehyde 脲醛树脂Urethane氨基甲酸乙脂Repair tag 修理單Resinoid 樹脂珞Resorcinol 間苯二酚樹脂Vacuum forming真空成型法Rosin松香醋酸乙烯及氯Roll leaf process 乙烯共聚物Rotary process 旋轉模造法氯乙烯及偏氯Rotation molding旋轉模造法乙烯共聚物Vinylidene 亚乙烯基Vinyls乙烯树脂SAN苯乙烯丙烯腈XSaturated hydrocarbon 飽和碳氫化合物Xylenol二甲酚Screw preplastication 螺旋預塑式Sebacic acidZSensitizing敏化工程Zinc stearate 硬脂酸锌Silica圭石Zirconia氧化锆Silicate圭鹽酸Silicones砂質樹脂Slush molding糊狀模型法Solvent molding溶劑模型法Snap-back vacuum forming 反彈式真空成型法SVinylchloride-acetate copolymerVinylchloride-vinylidene chloride copolymer VQUR。
塑料加工专业英语
塑料加工专业英语
Plastic Processing专业英语是指与塑料制品的加工工艺、产品设计、设备和工艺参数等相关的英语词汇和表达方式。
下面是一些相关的塑料加工专业英语词汇和表达方式：
1. Injection molding 注塑成型
2. Extrusion 挤出
3. Blow molding 吹塑
4. Rotational molding 旋转成型
5. Thermoforming 热成型
6. Compression molding 压缩成型
7. Calendering 挤压
8. Plasticizing 熔化
9. Melt temperature 熔融温度
10. Injection pressure 注塑压力
11. Cooling time 冷却时间
12. Mold cavity 模腔
13. Ejector pin 弹簧顶杆
14. Gate sprue 浇口
15. Runner system 平衡道
16. Mold release agent 脱模剂
17. Plasticizer 增塑剂
18. Reinforcement 增强剂
19. Melt flow index 熔体流动指数
20. Mold shrinkage 模具收缩率
这些词汇和表达方式可以帮助从事塑料加工专业的人更好地理解和沟通相关的技术和工艺要求。
塑料名称中英文对照
塑料名称中英文对照类别塑料类别俗称聚苯乙烯硬胶类不脆胶改性聚苯乙烯类聚丙烯类聚乙烯类中文学名通用聚苯乙烯高冲击聚苯乙烯丙烯腈-丁二烯-苯ABS 料乙烯AS 料(SAN料) 丙烯腈-苯乙烯BS(BDS)K料丁二烯-苯乙烯丙烯酸-苯乙烯-丙ASA 料烯睛PP(百折胶) 聚丙烯PPC 氯化聚丙烯LDPE(花料, 筒料) 低密度聚乙烯HDPE(孖力士) 高密度聚乙烯乙烯-醋酸乙烯脂氯化聚乙烯聚酰胺-6聚酰胺-66聚酰胺-9聚酰胺-1010聚甲基丙烯酸甲脂甲基丙烯酸甲脂-乙二烯聚碳酸脂聚甲醛硝酸纤维素醋酸纤维素乙基纤维素聚对苯二甲酸乙二醇脂英文学名General Purpose PolystyreneHigh Impact PolystyreneAcrylonitrile Butadiene StyreneAcrylonitrile StyreneButadiene StyreneAcrylonitrile Styrene acrylate copolymer英文简称主要用途PS 灯罩、仪器壳罩、玩具等HIPS 日用品、电器零件、玩具等ABS AS(SAN)BS(BDS)ASA PP PPC LDPE HDPE EVA CPE PA-6PA-66PA-9PA-1010PMMA MMB PC POM CN CA EC PET电器用品外壳, 日用品, 高级玩具, 运动用品日用透明器皿, 透明家庭电器用品等特种包装, 食品容器, 笔杆等适于制作一般建筑领域、户外家具、汽车外侧视镜壳体包装袋, 拉丝, 包装物, 日用品, 玩具等日用品，电器等包装胶袋, 胶花, 胶瓶电线, 包装物等包装, 建材, 水桶, 玩具等鞋底, 薄膜, 板片, 通管, 日用品等建材, 管材, 电缆绝缘层, 重包装材料轴承, 齿轮, 油管, 容器, 日用品机械, 汽车, 化工, 电器装置等机械零件, 泵, 电缆护套绳缆, 管材, 齿轮, 机械零件透明装饰材料, 灯罩, 挡风玻璃, 仪器表壳机器架壳, 框及日用品等高抗冲的透明件, 作高强度及耐冲击的零部件耐磨性好, 可以作机械的齿轮, 轴承等眼镜架, 玩具等家用器具, 工具手柄, 容器等工具手柄, 体育用品等轴承, 链条, 齿轮, 录音带等PolypropyleneChlorinated PolypropyleneLow Density PolyethyleneHigh Density PolyethyleneEthylene-Vinyl AcetateChlorinated PolyethylenePolyamide-6Polyamide-66Polyamide-9Polyamide-1010Polymethyl MethacrylateMethyl Methacrylate-ButadienePolycarbonatePolyoxymethylene(Polyformaldehyde)Cellulose NitrateCellulose AcetateEthyl CellulosePoly(Ethylene Terephthalare)改性聚乙EVA(橡皮胶)烯类CPE 尼龙单6聚酰胺尼龙孖6尼龙9热尼龙1010 丙烯酸脂类亚加力聚碳酸脂防弹胶聚甲醛赛钢纤维素类赛璐璐塑酸性胶饱和聚脂涤纶(的确凉)类别塑料类别俗称聚氯乙烯类PVC 性氟塑料类F4氟料PVFF46氟料F3氟料塑料聚砜中文学名英文学名聚对苯二甲酸丁二Poly(Butylene Terephthalare)醇脂Poly(Vinyl Chloride)聚氯乙烯聚四氟乙烯聚全氟代乙丙烯聚三氟氯乙烯注塑、挤出成型可溶性聚四氟乙烯注塑、挤出成型四氟乙烯-乙烯共聚四氟乙烯-六氯丙烯共聚三氟氯乙烯-乙烯共聚聚偏氟乙烯聚氟乙烯聚砜聚醚砜聚芳砜polysulfone polyethersulfone polyarylsulfone ChlorinatedPolyetherspoly(phenylene oxide)poly(phenylene sulfone)Polytetrafluoroethylene Polychlorctrifluoreethylene Teflon英文简称PBT PVC PTFE PCTFE PFA ETFE主要用途制造棒, 管, 板材, 输油管, 电线绝缘层, 密封件等高频电子仪器, 雷达绝缘部件高频电子仪器, 雷达绝缘部件透明视镜, 阀管件等化工配件、机械零件、电线保护膜，可塑性成型化工配件、机械零件、电线保护膜电线被覆、薄膜（绝缘膜、板材保护膜、脱模膜）、衬里主要用于电缆Perfluorinated Ethylene-Propylene CopolymerFFP ，F46Fluorinated Ethylene-propyleneECTFEFEP ECTFE PVdF氯化聚醚聚苯醚聚芳脂聚苯硫醚聚醚酮聚亚胺氯化聚醚聚苯醚聚芳脂聚苯硫醚聚醚醚砜结晶型聚酰亚胺化工配件、机械零件、电线保护膜，电缆电容器薄膜、长寿命耐候性建筑涂料可塑性成型PVF 主要制作薄膜和涂料，用于建筑、交通和包装等PSU(PSF)电器零件, 结构件, 飞机及汽车零件等PES 电器零件, 结构件, 飞机及汽车零件等可用作C 级绝缘材料制造电子电器零件，代替金属PAS、陶瓷等材料制造机械零件PENTON(CPT)代替不锈钢, 氯塑料等材料PPO ，MPPO 较高温度下工作的齿轮, 轴承, 化工设备及零部件PAR 汽车电器, 医疗器械PPS 耐热性优良, 电器零件, 汽车零件, 化学设备PEEK 耐化学品、电线被覆、高温接线柱、凸轮耐高温、自润滑、耐磨太空, 电子, 飞机零件, 汽车零Polyimides PAI件类别塑料类别俗称中文学名非结晶型聚醚亚胺英文学名热固性双马来酰亚胺液晶聚合物自增强聚合物聚甲基戊烯-1聚甲基戊烯-1苯酚-甲醛树脂酚醛塑料电木粉脲-甲醛树脂氨基塑料电玉尿素科学瓷, 美腊密三聚氰氨甲醛树脂热苯氨-甲醛树脂固环氧树脂冷凝胶环氧树脂性PU 聚氨脂树脂塑聚氨脂Silicone 硅氧烷料硅树脂不饱和聚醇酸树脂脂烯丙基树脂Self-reinforced polymerPhenol-Formaldehyde Urea-FormaldehydeMelamine-Formaldehyde ResinAniline-Formaldehyde ResinEpoxide ResinPolyurethane ResinAlkyd ResinAllyl Resin主要用途耐高温、自润滑、耐磨太空, 电子, 飞机零件, 汽车零Polyimides PEI件耐高温、自润滑、耐磨太空, 电子, 飞机零件, 汽车零Polyimides BMI件LCP 微波炉灶容器，电子电器和汽车机械零件TPX 一次性注射器, 奶瓶, 汽车灯罩PF 无声齿轮, 轴承, 钢盔, 电机, 通讯器材配件等UF 生活用品, 电机壳, 木材粘接剂等MF 食品, 日用品, 开关零件等AF EP 汽车拖拉机零件, 船身涂料PU 鞋底, 椅垫床垫, 人造皮革, 油漆SI 橡胶制品, 脱模剂, 乳液弹性体, 清漆涂料等AK DAP涂料, 玻璃钢, 装饰件, 地板, 钮扣等英文简称。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
塑料材质中英文对照表
ABS Acrylonitrile-Butadiene-Styrene 丙烯腈-丁二烯-苯乙烯共聚合物
ASA Acrylic-styrene-acrylonitrile 丙烯酸-苯乙烯-丙烯腈
CA Cellulose Acetate 纤维素醋酸酯
CAP Cellulose Acetate Propionate 纤维素醋酸丙酸酯
CB Cellulose Butyrate 纤维素酪酸酯
CP Cellulose Propionate 纤维素丙酸酯
CTFE Polychlorotrifluoroethylene 聚一氯三氟乙烯
EAA Ethylene Acrylic Acid(TP) 乙烯丙烯酸
EAE Ethylene Acrylic Ester(TP) 乙烯丙烯酸乙酯
ECTFE Ethylene-chlorotrifluoroeethylene 乙烯一氯三氟乙烯共聚合物
EMA Ethylene Methyl Acrylate(TP) 乙烯甲基丙烯酸酯
EMAA Ethylene Methacrylic Acid 乙烯丙烯酸甲酯
ENBA Ethylene N-Butyl Acrylate(TP) 乙烯丁基丙烯酸酯
ETFE Copolymer of ethylene and chlorotetrafluoroethylene 乙烯一氯四氟乙烯共聚合物EVA Ethylene Vinyl Acetate(TP) 乙烯乙基丙烯酸酯
EVOH Ethylene Vinyl Silane(TP) 乙烯乙基醇
FEP Fluorinated ethylene-propylene 氟化乙烯丙烯
HDPE High density Polyethylene 高密度聚乙烯
LCP Liquid crystal polyester 液晶聚酯
LDPE Low density Polyethylene 低密度聚乙烯
LLDPE Linear Low density Polyethylene 线性低密度聚乙烯
IONOMER lonomer 离子聚合物
MDPE Medium density Polyethylene 中密度聚乙烯
PA Polyamide 聚醯胺
PA11 Polyamide 11 聚醯胺11
PA12 Polyamide 12 聚醯胺12
PA4/6 Polyamide 4/6 聚醯胺4/6
PA6 Polyamide 6 聚醯胺6
PA6/10 Polyamide 6/10 聚醯胺6/10
PA6/12 Polyamide 6/12 聚醯胺6/12
PA6/6 Polyamide 6/6 聚醯胺6/6
PA6/9 Polyamide 6/9 聚醯胺6/9
PAI Polyamide-imide 聚醯胺醯亚胺
PBT Polybutylene terephathalate 聚对苯二甲酸二丁酯
PC Polycarbonate 聚碳酸酯
PCT Polycarbonate hexandimethanol Terephthalate 聚环已醇二乙酯
PEC Polyethylene-Chlorinated 氯化聚乙烯
PEEK Polyetheretherketone 聚醚醚酮
PEI Polyetherimide 聚醚醯亚胺
PES Polyethersulfone 聚醚
PET Polyethylene terephathalate 聚对苯二甲酸二乙酯
PETG Glycol-Polyethylene terephathalate 二元醇改质聚对苯二甲酸二乙酯PFA Perfluoroalkoxy 过氟烷氧基
PI Polyimide 聚醯亚胺
PK Polyketone 聚酮
PMMA Polymethylmethacrylic 聚甲基丙烯酸甲酯PMP Polymethylpentene 聚甲基戊烯
Polyolefin Polyolefin 聚烯烃
POM Polyacetal 聚缩醛
PP Polypropylene(TP) 聚丙烯
PPA Polyphthalamide 聚酞酸酯
PPE Polyphenylene Ether 聚苯醚
PPO Polyphenylene Oxide 聚氧化二甲苯
PPS Polyphenylene Sulfide 聚硫化苯
PS Polystyrene(TP) 聚苯乙烯
PSF Polysulfone(TP) 聚碸
PTFE Polytetrafluorothylene 聚四氟乙烯
PU Polyurethane(TP) 聚氨基甲酸乙酯
PVC Polyvinyl Chloride(TP) 聚氯乙烯
PVDC Polyvinyl Dichloride 聚二氯乙烯
PVDF Polyvin ylidene fluoride 聚氟化乙二烯
SAN(AS) Styrene-Acrylonitrile 苯乙烯-丙烯腈
SB Styrene-Butadiene 苯乙烯-丁二烯
SMA Styrene Maleic Anhydride 苯乙烯-马来酐TPE Thermoplastic Elastomer (TPE) 热塑性弹性体
TPO Thermoplastic Polyolefin(TPO) 热塑性聚烯烃。