2012吉普大切诺基底盘升降说明书
悬架系统产品说明 - 拜拉豪斯 Jeep Wrangler JL (2018年及更新版)说明书
JEEP WRANGLER JL (18+)PERFORMANCE SERIES 2.0 RESERVOIR:885-24-183 - Kit: 18-On Jeep JL Front, PS, 2.0, R/R, 2-3″ Lift885-26-183 - Kit: 18-On Jeep JL Front, PS, 2.0, R/R, 2-3″ Lift, CD Adjuster885-24-185 - Kit: 18-On Jeep JL Front, PS, 2.0, R/R, 3.5-4″ Lift885-26-185 - Kit: 18-On Jeep JL Front, PS, 2.0, R/R, 3.5-4″ Lift, CD Adjuster885-24-187 - Kit: 18-On Jeep JL Front, PS, 2.0, R/R, 4.5-6″ Lift885-26-187 - Kit: 18-On Jeep JL Front, PS, 2.0, R/R, 4.5-6″ Lift, CD Adjuster985-24-184 - 18-On Jeep JL Rear, PS, 2.0, R/R, 11.6”, 2-3″ Lift985-26-184 - 18-On Jeep JL Rear, PS, 2.0, R/R, 11.6”, 2-3″ Lift, CD Adjuster985-24-186- 18-On Jeep JL Rear, PS, 2.0, R/R, 12.1”, 3.5-4″ Lift985-26-186 - 18-On Jeep JL Rear, PS, 2.0, R/R, 12.1”, 3.5-4″ Lift, CD Adjuster985-26-188 - 18-On Jeep JL Rear, PS, 2.0, R/R, 13.1”, 4.5-6″ Lift985-26-188 - 18-On Jeep JL Rear, PS, 2.0, R/R, 13.1”, 4.5-6″ Lift, CD Adjuster FACTORY RACE SERIES 2.5 RESERVOIR883-26-049 - 18-ON Jeep JL, FRONT, 2.5 Truck FRS, R/R, 0-1.5″ Lift, DSC883-26-053 - 18-ON Jeep JL, REAR, 2.5 Truck FRS, R/R, 0-1.5″ Lift, DSC883-26-050 - 18-ON Jeep JL, FRONT, 2.5 Truck FRS, R/R, 2-3″ Lift, DSC883-26-054 - 18-ON Jeep JL, REAR, 2.5 Truck FRS, R/R, 2-3″ Lift, DSC883-26-051 - 18-ON Jeep JL, FRONT, 2.5 Truck FRS, R/R, 3.5-4″ Lift, DSC883-26-055 - 18-ON Jeep JL, REAR, 2.5 Truck FRS, R/R, 3.5-4″ Lift, DSC883-26-052 - 18-ON Jeep JL, FRONT, 2.5 Truck FRS, R/R, 4.5-6″ Lift, DSC883-26-056 - 18-ON Jeep JL, REAR, 2.5 Truck FRS, R/R, 4.5-6″ Lift, DSC 750 VERNON WAY SUITE 101. EL CAJON, CA 92020 USAThank you for choosing FOX direct-replacement shocks for your vehicle. FOX products are designed, tested, and manufactured by the finest professionals in the industry.FOX recommends that you become completely familiar with the handling characteristics of your modified vehicle before operating it under rigorous conditions, helping to avoid potential rollover situations and other loss of control events. FOX further recommends that you use appropriate protective equipment at all times when operating your vehicle.To achieve the best performance and product longevity, periodic service and maintenance is required. Please referto the Service and Upgrades section for more information.SAFETY INSTRUCTIONS• F OX direct-replacement shocks aredesigned to fit and allow properclearance with the stock suspension. If aftermarket suspension componentsare installed it is the customersresponsibility to ensure that at full cycle the suspension clears the FOX shocks.• F OX direct-replacement shocksshould always be installed as a pair for maximum performance.• P roper installation and serviceprocedures are essential for the safeand reliable installation of chassisparts, requiring the experience andtools specially designed for thispurpose. Installation and maintenance procedures for this product mustbe performed by a qualified servicetechnician, to avoid potentially unsafevehicle handling characteristics,which may result in SERIOUSINJURY or DEATH.• M odifying your vehicle’s suspension will change the handling characteristics of your vehicle. Under certain conditions,1.800.FOX.SHOX(369.7469)*********************************1your modified vehicle may be moresusceptible to loss of control or rollover, which can result in SERIOUS INJURYor DEATH. Thoroughly familiarize yourself with the modified vehicle handling characteristics before any rigorous vehicle operation. Wearbody protective gear includinghead protection when appropriate. Installation of vehicle roll bars or cage is highly recommended.• F OX direct-replacement shocks aregas-charged and are highly pressurized. Placing shocks in a vise or clamp, applying heat, or attempting to openor service the shock without the proper tools and training can result in SERIOUS INJURY or DEATH. Do not attempt to modify, puncture or incinerate a FOX direct-replacement shock absorber.• A ny attempt to misuse, misapply, modify, or tamper with any FOX product voids any warranty and may result in SERIOUS INJURY or DEATH.• A lways use a chassis lift for the installation of shocks, and make certain that the raised vehicle is securely attached to the lift to prevent the vehicle from slipping, falling, or moving during the installation process.• D O NOT install any FOX product without the necessary special tools, expertise and chassis lift, or you will subject yourself to the risk of SERIOUS INJURY or DEATH. If you elect tonot use a chassis lift (which election may result in SERIOUS INJURY or DEATH), ensure that the vehicle ison level ground, that all tires on the ground during installation are blocked to prevent vehicle movement, that at least two tires are on the ground at all times, and that adequately secured jack stands are used to support the vehicle. NEVER get under the vehicle until you have checked to ensure that the vehicle will be stable during installation.• F OX direct-replacement shocks are designed to fit your vehicle’s shock mounts with no modifications with the 750 VERNON WAY SUITE 101. EL CAJON, CA 92020 USA 23/8″ self-tapping screw. If installing 2.5 Factory Race Series shocks,ensure that the bracket is facing the front of the vehicle. If installing 2.0 Performance Series Remote Reservoirexception of reservoir placement on specific models and applications.INSTRUCTIONS - FRONTMedium-strength thread locker (blue) is recommended on all bolts.1. Please read the installation guidelinesfor instructions on how to properly lift and secure the vehicle.2. Remove both front wheels.3. Remove front stock shocks. Do notdiscard OEM hardware. This will be used in later steps.4. Install the supplied reservoir bracketsto the vehicle behind the bumper above the skid plate. If equipping a Jeep JL Rubicon, place the center hole on the supplied Fox bracket 2 ¼″ below the hole on the front bumper bar (Fig. 1). If equipping a Jeep JLNon-Rubicon, place the center hole of the supplied Fox bracket 2 ¾″ below the hole on the front bumper bar (Fig. 2). Use the bracket to mark the center hole on the bracket. Using a 7/32″ drill bit and the marked location of the hole, drill a pilot hole for the supplied 3/8″ self-tapping screw. Secure thebracket using the suppliedFig. 1: RUBICON(passenger side): Use the bottom 2holes on the bracket to mount.Fig. 2: NON-RUBICON(passenger side): Use the top 2holes on the bracket to mount.1.800.FOX.SHOX(369.7469)*********************************3shocks, ensure that the bracket is facing the rear of the vehicle.(Fig. 3). Ensure the bracket is straight vertically. Drill the remaining pilot holes and install self-tapping screws.5. Connect the FOX shock to thetop vehicle mount using theOEM hardware. Torque to OEMspecifications. Ensure that the upper, longer, bushing spacer is facing theinside of the vehicle and the hosefitting is facing outward.6. Connect the Fox Shock to the lowermount using the OEM hardware.Torque to OEM specifications.7. Using two supplied billet clampsand screws, mount the reservoir tothe brackets. Utilize the slots in thebracket to locate clamps. Do not feed the clamps through the slots in thebrackets. (Figs. 4-5)8. Check that the suspension has properclearance by steering completely inboth directions.9. Reinstall both front wheels and torqueto OEM specifications. 750 VERNON WAY SUITE 101. EL CAJON, CA 92020 USA 4INSTRUCTIONS - REARMedium-strength thread locker (blue) is recommended on all bolts.1. Please read the INSTALLATIONGUIDELINES for instructions on how to properly lift and secure the vehicle.2. Remove rear wheels.3. Remove rear stock shocks. Do notdiscard OEM hardware. This will be used in later steps.4. Reusing the OEM hardware, installthe new FOX shock with the reservoir pointing towards the rear and angled outwards (Fig. 6). Torque to OEM specifications.5. Check that the suspension has properclearance.6. Reinstall both rear wheels and torqueto OEM specifications.Fig. 5: (Passenger side): Performance Series 2.0ReservoirPERFORMACE SERIES SHOCKS: Zip tie the reservoir hose with the included zip ties so that it does notprotrude into the wheel well. Fender trimming can be done to make the reservoir hose more visible.NOTE: FOR PERFORMANCE SERIES SHOCKS. When mounting the reservoir clamp, use a 1⁄₄″ hex (Allen) key with the supplied bolt and clamp assembly to mount the reservoir to the body of the shock. Tourque the bolt to 25 ftlbs. DO NOT OVER TIGHTEN as this could result in damage to the shock. Ensure that you have the clamp facing outward so that you can see the FOX logo from the side of the vehicle. Do not mount the clamp over a decal as this could damage the decal.Fig. 4: (Passenger side): Factory Race Series 2.5 Reservoir1.800.FOX.SHOX(369.7469)*********************************5Fig. 6: Passenger‘s Side: Factory Race Series (Left),Performance Series (Right)12 CLICKS10 CLICKS10 CLICKSDSC HIGH SPEEDDSC LOW SPEED 750 VERNON WAY SUITE 101. EL CAJON, CA 92020 USA6FOX LIMITED WARRANTYFOX Factory, Inc., a California corporation having offices at 130 Hangar Way, Watsonville, CA 95076 (“FOX”), makes the following LIMITED WARRANTY with respect to its suspension products:LIMITED ONE (1) YEAR WARRANTY ON SUSPENSION PRODUCTSSubject to the limitations, terms and conditions hereof, FOX warrants, tothe original retail owner of each newFOX suspension product, that theFOX suspension product, when new,is free from defects in materials and workmanship. Unless otherwise required by law, this warranty expires one (1)year from the date of the original FOX suspension product retail purchasefrom an authorized FOX dealer or froma FOX authorized Original Equipment Manufacturer where FOX suspensionis included as original equipment ona purchased vehicle. If law requires a warranty duration of greater than one (1) year, then, subject to the other provisions hereof, this warranty will expire at the end of the minimum warranty period required by such law.TERMS OF WARRANTYThis warranty is conditioned on the FOX suspension product being operatedunder normal conditions and properly maintained as specified by FOX. This warranty is only applicable to FOX suspensions purchased new from an authorized FOX source and is madeonly to the original retail owner of thenew FOX suspension product and is not transferable to subsequent owners. This warranty is void if the FOX suspension product is subjected to abuse, neglect, improper or unauthorized repair, improper or unauthorized service or maintenance, alteration, modification, accident or other abnormal, excessive, or improper use.Should it be determined by FOX in itssole and final discretion, that a FOX suspension product is covered by this warranty, it will be repaired or replaced, by a comparable model, at FOX’ssole option, which will be conclusiveand binding. THIS IS THE EXCLUSIVE REMEDY UNDER THIS WARRANTY.ANY AND ALL OTHER REMEDIES AND DAMAGES THAT MAY OTHERWISEBE APPLICABLE ARE EXCLUDED, INCLUDING, BUT NOT LIMITED TO,1.800.FOX.SHOX(369.7469)*********************************7INCIDENTAL OR CONSEQUENTIAL DAMAGES OR PUNATIVE DAMAGES.This limited warranty does not apply to normal wear and tear, malfunctions or failures that result from abuse, improper assembly, neglect, alteration, improper maintenance, crash, misuse or collision. This limited warranty gives the consumer specific legal rights. The consumer may also have other legal rights which vary from state to state or country to country. Some states and countries do not allow the exclusion or limitation of incidental or consequential damages or warranties, and if dictated by law the above limitationsor exclusions may not apply to you. If itis determined by a court of competent jurisdiction that a certain provision of this limited warranty does not apply, such determination shall not affect any other provision of this limited warranty and all other provisions shall remain in full effect THIS IS THE ONLY WARRANTYMADE BY FOX ON ITS SUSPENSION PRODUCTS AND COMPONENTS, AND THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION HEREIN. ANY WARRANTIES THATMAY OTHERWISE BE IMPLIED BYLAW INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED 750 VERNON WAY SUITE 101. EL CAJON, CA 92020 USA 8151.800.FOX.SHOX(369.7469)*********************************9 750 VERNON WAY SUITE 101. EL CAJON, CA 92020 USA 1.800.FOX.SHOX(369.7469)********************************* PN 605-01-231 REV A AUGUST 2018。
1986-95 Jeep Wrangler 自带型号安装说明书
1986-95 JEEP WRANGLERBODY LIFTINSTALLATION INSTRUCTIONS Automatic Transmisson2” Lift932A3” Lift933A Manual Transmission2” Lift(1) 9323” Lift(2) 933 (1)Kit 932 can be installed on a vehicle withautomatic transmission, but installation requires Kit 932APK (sold separately).(2)Kit 933 can be installed on a vehicle withautomatic transmission, but installation requires Kit 933APK (sold separately).WARNINGInstallation of a body lift will change the center of grav-ity and the handling characteristics of the vehicle. Because of the higher center of gravity and larger tires, the vehicle will handle and react differently both on and off-road. You must drive it safely! Extreme care must be taken to prevent vehicle rollover or loss of control, which could result in serious injury or death. Avoid sudden sharp turns or abrupt maneuvers and always make sure all vehicle occupants have their seat belts fastened.CAUTIONProper installation of a body lift kit requires knowledge of the factory recommended procedures for disassem-bly and assembly of original equipment components. We recommend that the factory shop manual and any special tools necessary to your vehicle be on hand during the installation. Installation of this body lift kit without proper knowledge of the factory recommended procedures may affect the performance of these com-ponents and the safety of your vehicle. We strongly recommend that a certified mechanic familiar with the installation of similar components install this body lift kit.WARNINGThis body lift kit should only be installed on vehicles in good working condition. Before installation, the vehi-cle should be thoroughly inspected for evidence of cor-rosion or deformation of the sheet metal around the factory body mounts. This body lift kit should not be installed on any vehicle that is suspected to have been in a collision or misused. Off-road use of your vehicle with this body lift installed may increase the stress applied to the factory body mounts. We do not recom-mend that any vehicle with a body lift installed be involved in any extreme off-road maneuvers such as jumping. Failure to observe this warning may result in serious personal injury and/or severe damage to your vehicle.WARNINGMany states now have laws restricting bumper heights and vehicle lifts. Local laws should be consulted to determine if the changes you intend to make to your vehicle comply with state laws. Before combining a body lift with a suspension lift, consult an installation professional to see how this will affect your specific application.WARNINGThe installation of larger wheel and tire combinations may reduce the effectiveness of the braking system.WARNINGWe will not warranty any damage to the A/C system. WARNINGAlways wear eye protection when operating power tools.WARNINGEnsure that your vehicle tires are properly blocked and secured before you begin installation of this lift kit.NOTEWe recommend using the Loctite® supplied in the kiton all hardware unless noted in the instructions.1.Carefully read all warnings and instructions com-pletely before beginning.2.Verify all parts have been received in this kit bychecking the parts list at the end of this document. 3.Only install this kit on the vehicle for which it isspecified. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-7080.4.Special tools needed:a.Welder or access to a professional weldingshop.5.Park the vehicle on a clean, dry, flat, level surfaceand block the tires so the vehicle cannot roll in either direction.6.Battery cables: Disconnect both battery cables. Besure to disconnect the negative cable first, then the positive cable.7.“Jeep cover”: Remove the plastic “Jeep” coverfrom the frame in front of the grille.8.Automatic transmission: Loosen the lock nutsecuring the 4WD shift knob. Remove the 4WD shift knob. Remove the shift boot mounting screws. Care-fully remove the shift boot from the shift lever.9.Manual transmission: Loosen the lock nut securingthe transmission shift knob. Remove the transmis-sion shift knob. Loosen the lock nut securing the 4WD shift knob. Remove the 4WD shift knob.Remove the shift boot mounting screws. Carefully remove the shift boot from the shift levers.10.Air intake duct: Remove the air intake duct from thecore support. Remove the top screw and gently pull up and out away from the core support.NOTE: On vehicles with power steering, it may be necessary to remove the power steering reservoir from the core support.11.Radiator: Remove six radiator mounting bolts.(Later, the vent hose will be relocated to the middle radiator mount.) Lift the radiator up to pull the locat-ing tab out of the core support. Gently bend the locating tabs flat.12.A/T shift linkage: Remove the upper linkage rodfrom the steering column lever. Remove the lower linkage rod from the pivot assembly. Remove the two bolts that mount the pivot assembly to the pivot bracket. Remove the linkage and pivot assembly from the vehicle.13.Steering shaft: Mark the steering shaft where itattaches to the steering gearbox (at the splined shaft) and where it attaches to the column at the fire-wall. This will ensure proper alignment after the lift-ing operation is complete. Remove the bolt attaching the steering shaft to the gearbox. Remove the bolt attaching the steering shaft to the column at the fire-wall. Remove the steering shaft from the vehicle. 14.Vacuum hoses: Disconnect the vacuum hoses thatgo from the engine to the vacuum canister on the drivers side fender well. One hose will need to be lengthened.15.Heat shield: The heat shield above the muffler willneed to be trimmed to allow the exhaust hanger to be lowered. Mark the heat shield along the line of the exhaust hangers. Remove the heat shield mounting screws. Remove the bolts securing the exhaust hangers to the body. Remove exhaust from the rear frame hanger. Remove the heat shield from the vehicle.WARNING: Gasoline is highly flammable and explo-sive. Use extreme care when working near gasoline.16.Fuel filler: Remove the plastic tabs that hold the fuelfilter hose cover over the fuel filler hose. Loosen the hose clamps that attach the fuel filler and the vent hose to the filler neck. The filler hose may need to be adjusted after lifting the bed.NOTEKit parts are prefaced by the word kit and appear in bold print.NOTEIf parts are missing from kit, please be prepared to pro-vide the following information:1. Name of purchase location2. Bar Code on side of box3. Date above bar code4. Date inside box cover5. Inspector # from inside box cover17.Body mount bolts (loosen): Loosen, but DO NOTremove, all 11 body mount bolts:a.1 at the front center of the grilleb.6 along the frame rail, under the doors (three oneach side)c.2 along the frame rail, just behind the rearwheels (one on each side),d.2 on the rear frame rail at the very rear of thevehicle18.Kit blocks (passenger side): Remove the bodymounting bolts from the passenger side of the vehi-cle and the front center mount only. Using a hydrau-lic jack and a wooden block, slowly lift the passenger side of the vehicle just high enough to place the kit blocks on the frame mounts, constantly checking to ensure wires, hoses, cables, etc. are not binding.Install the 3” diameter kit blocks on the frame rail mounts under the doors (three on each side of the vehicle). Install the 2” diameter kit blocks on the other mounts (except the front center mount; it is not possible to place a kit block under the front center mount until the driver side of the vehicle has been lifted).19.Kit bolts (passenger side): Install the kit bolts andthe stock body mount bushings as follows (DO NOT tighten):•along the frame rail, under the doors:1/2” x 6 1/2” (5 1/2” for 2" lift)•along the frame rail, behind the rear wheels: 7/16” x 5 1/2” (4 1/2” for 2" lift)•two rear mounts:7/16” x 5 1/2” (4 1/2” for 2" lift)20.Kit blocks and bolts (driver side): Repeat the pre-vious steps to install the kit blocks and kit bolts on the driver side of the vehicle. Also, install a kit block and kit bolt (7/16” x 51/2” <41/2” for 2” lift>) at the front center mount.21.Kit brackets near grille: Tack-weld two kit brackets(front body support) onto the frame below the rubber pad on each side of the grille. A certified welder should perform all welding. If desired, paint the kit brackets to prevent rust.22.Kit bolts (tighten): Remove each kit bolt one at atime, apply Loctite® to the threads, install it, and tighten it according to the vehicle manufacturer’s specification.WARNING: The steering shaft contains two spring clips (a small one and a large one) that are shaped like leaf springs. These spring clips maintain tension between both halves of the steering shaft. To pre-vent the shaft from fully separating, be sure that the large spring clip remains in the original position and that the shaft is not extended far enough to expose the large spring clip.23.Steering shaft: Slide the rubber grommet down,away from the slip joint. Extend the steering shaft until the small spring clip is exposed. (If necessary, secure one end of the steering shaft in a vice and pull hard on the other end.) Remove the small spring clip. Slide the rubber grommet back to its original position.Install the steering shaft, ensuring the marks made earlier are aligned. Apply Loctite® to the threads of both steering shaft mounting bolts.Install steering shaft mounting bolts. Tighten bolts to the manufacturer’s specification.933 & 933AKit Bracket (Front Body Support)932 & 932A24.4WD shift lever : Remove the spring clips that attachthe shift lever to the transfer case. Remove the shift lever from the vehicle. Scribe a line along the axis of the shift lever, just below the bend. (Later, before welding, this line will be used to ensure the pieces of the shift lever are oriented correctly.) Cut the shift lever through the scribed line. Weld the kit exten-sion (4WD shift lever) between the two pieces, ensuring the scribed lines are aligned. A certified welder should perform all welding. If desired, paint the shift lever to prevent rust. Shift the transfer case into all ranges. If the shift lever contacts the floor, heat and bend the shift lever and/or notch the floor.25.Manual transmission: Shift the transmission into allgears. If the shift lever contacts the floor, heat and bend the shift lever and/or notch the floor.26.Shift lever boots : If an inner boot was removed, donot install it. Install shift boot mounting screws. Check the operation of both shift levers again. If nec-essary, trim the shift boot housing. Install both gear-shift knobs and the lock nuts.27.A/T upper shift linkage rod : Scribe a line along astraight part of the upper shift linkage rod. Cut the rod in half through the scribed line. Weld the kit extension (A/T shift linkage) between the halves of the rod, ensuring the scribed lines are aligned. If desired, paint the rod to prevent rust.28.A/T shift pivot : Install kit bracket (A/T shift pivot) onthe stock pivot bracket using the stock fasteners. Install the pivot assembly and linkage in the vehicle. Install the pivot assembly into the stock engine-mounted pivot bracket and the kit bracket . Attach the pivot assembly to the kit bracket using two kit bolts (1/4 x 1”), four kit washers (1/4” SAE), and two kit nuts (1/4” nylock). DO NOT tighten. Connect the lower end of the shift linkage rod to the pivot assembly. Connect the upper end to the steering column lever. Tighten the pivot assembly mounting bolts.NOTE : In the following step, it may be necessary to install the kit brackets on the core support via the studs protruding from the brackets (in other words, opposite of the way specified).29.Radiator : Install six kit brackets (radiator) on thecore support using the stock bolts. DO NOT tighten. Install the radiator on the 1/4” studs protruding from the kit brackets . At each stud, install one kit washer (1/4” SAE) and one kit nut (1/4” nylock). DO NOT tighten. Adjust clearance between the fan and fan shroud. Install the vent hose to the middle radiator mount. Tighten the radiator mounting bolts. If the power steering reservoir was removed, install the reservoir on the core support. Install the air intake duct on the core support.30.Vacuum hoses : Connect the vacuum hoses to thevacuum canister. If a hose is too short, replace it or extend it with the kit hose(1/4”).Kit Extension(4WD Shift Lever)(932 & 932A is shown; 933 & 933A is similar)Kit Extension(A/T Shift Linkage)(932 & 932A is shown;933 & 933A is similar)Kit Bracket(A/T Shift Pivot)932A933A932 & 932A Kit Bracket (Radiator)933 & 933A31.Exhaust heat shield: Trim the exhaust heat shieldaccording to the marks made earlier. Drill exhaust hanger mounting holes (in the body) to 5/16”. Install the kit brackets (exhaust hanger) to the original holes (the ones that were just drilled) using two kit bolts (5/16” x 2 3/4”), four kit washers (5/16”), and two kit nuts (5/16” nylock). DO NOT tighten. Install the heat shield on the body. Tighten all mounting screws securely. Install the exhaust hanger on the kit brackets using four kit bolts (1/4” x 1"), eight kit washers (1/4” SAE), and four kit nuts (1/4” nylock).Install the exhaust on the rear frame hanger. Tighten all exhaust hardware.32.Parking brake cable: Bend the parking brake cablebracket that is over the rear differential straight up and down.WARNING: Gasoline is highly flammable and explo-sive. Use extreme care when working near gasoline.33.Fuel filler: Adjust the fuel filler hose as necessary.Tighten both hose clamps securely. Install the cover over the fuel filler hose. It may not be possible to engage all of the plastic tabs without binding the filler hose; engage as many tabs as possible.34.“Jeep” cover: Install the plastic “Jeep” cover on thefront of the vehicle.35.Battery cables: Connect both battery cables. Besure to connect the positive cable, then the negative.36.Static vehicle check: Place the warning label(sticker) on the dash in plain sight of all vehicle occu-pants. Check the operation of the transmission and transfer case. Be sure that there is complete engagement in all gears and 4WD ranges. Be sure that the fan cannot contact the fan shroud. Check again for any binding wires, cables, hoses, etc.Check steering operation. Turn the steering wheel from side to side. Be sure that there is no binding. 37.Dynamic vehicle check: Drive vehicle in all gearsand 4WD ranges. Check operation of all vehicle sys-tems (brakes, steering, clutch, etc.). Double-check all hardware and all vehicle systems again in 500 miles and as part of your regular maintenance schedule.AccessoriesThe following accessories are also available:82095: Sport Cage83095: Rock Slider Front Bumper83096: Rock Slider Front Bumper w/ Grille Guard 83100: Rock Slider Rear Bumper84095: Rock Slider Side Bars85095: Swing-Away Tire/Can Carrier86095: Swing-Away Tire Carrier87003: Streamer Bar (for Sport Cage)87009: Dash Bar (for Sport Cage)87011: Multi-Light Mount (for Rock Slider Front Bumper) 87012: Bolt Plate Adapter (for Tire- & Tire/Can Carriers) 87013: Non-Lip Fuel Can Adapter (for Tire/Can Carrier) 87269: Cargo Box (for Tire/Can Carrier)Kit Bracket (Exhaust Hanger)Parts List932Qty.Description5Block, 2” height x 2” diameter 6Block, 2” height x 3” diameter 4Bolt, 1/4” x 1”2Bolt, 5/16” x 2 3/4”5Bolt, 7/16” x 4 1/2”6Bolt, 1/2” x 5 1/2”4Bracket, exhaust hanger2Bracket, front body support 6Bracket, radiator1Extension, 4WD shift lever 1Hose, 1/4” x 6”10Nut, 1/4” Nylock2Nut, 5/16” Nylock14Washer, 1/4” SAE4Washer, 5/16” SAE932AQty.Description5Block, 2” height x 2” diameter 6Block, 2” height x 3” diameter 6Bolt, 1/4” x 1”2Bolt, 5/16” x 2 3/4”5Bolt, 7/16” x 4 1/2”6Bolt, 1/2” x 5 1/2”1Bracket, A/T shift pivot4Bracket, exhaust hanger2Bracket, front body support 6Bracket, radiator1Extension, 4WD shift lever 1Extension, A/T shift linkage 1Hose, 1/4” x 6”12Nut, 1/4” Nylock2Nut, 5/16” Nylock18Washer, 1/4” SAE4Washer, 5/16” SAE 933Qty.Description5Block, 3” height x 2” diameter 6Block, 3” height x 3” diameter 4Bolt, 1/4” x 1”2Bolt, 5/16” x 2 3/4”5Bolt, 7/16” x 5 1/2”6Bolt, 1/2” x 6 1/2”4Bracket, exhaust hanger2Bracket, front body support 6Bracket, radiator1Extension, 4WD shift lever 1Hose, 1/4” x 6”10Nut, 1/4” Nylock2Nut, 5/16” Nylock14Washer, 1/4” SAE4Washer, 5/16” SAE933AQty.Description5Block, 3” height x 2” diameter 6Block, 3” height x 3” diameter 6Bolt, 1/4” x 1”2Bolt, 5/16” x 2 3/4”5Bolt, 7/16” x 5 1/2”6Bolt, 1/2” x 6 1/2”1Bracket, A/T shift pivot4Bracket, exhaust hanger2Bracket, front body support 6Bracket, radiator1Extension, 4WD shift lever 1Extension, A/T shift linkage 1Hose, 1/4” x 6”12Nut, 1/4” Nylock2Nut, 5/16” Nylock18Washer, 1/4” SAE4Washer, 5/16” SAERev. 2, Copyright 12/04 Performance Automotive GroupBracket, A/T shift pivot (932A)Bracket, A/T shift pivot (933A)Bracket , exhaust hangerBracket , front body support(932 & 932A)Bracket, front body support (933 & 933A)Extension , 4WD shift lever(1/2” x 2”)(932 is shown; 933 is similar)Extension , A/T shift linkage(3/8” x 2”)(932A is shown; 933A is similar)Bracket , radiator (932 & 932A)Bracket , radiator (933 & 933A)。
汽车举升机操作规程和操作流程
汽车升降机操作规程操作说明：1、使用前，检查紧固件在运输或使用过程中是否松动，各润滑部位，丝杠、丝母、导向轮、行走轮是否加轮滑，一切就绪后，将电源及四柱和行程开关的线路，按照电控的顺序分别接入电柜后面的端子排上。
2、电源线接通后，按动总动上升、下降，单机上升、下降，用手触动各柱的行程开关是否起作用，提升按钮开关的指示是否与起重机的指示相同，如出现不同，请将电源线或电机线的两相线互换位置即可。
3、无负荷试验无问题后，方可进行载重举升。
载重举升时，将举升机降至最低位置，并将四柱举升机的叉推到可以举升四个车轮的位置，按总动上升开关，举升机开始将汽车升起，达到最高位置时，任意一机触动行程开关，便可自动停机。
4、单机升降开关是用来调整各柱托叉的，在调整平衡时，必须在上下行程开关不工作时执行。
想法很重要：1、举升机在升降工作时，任何人不得从车下进入，以防不安全的事故发生。
2、举升机工作结束后，必须将电源开关转到“OFF”位置。
3、举升机在升降过程中，不应全依赖上下行程开关停机。
因为行程开关由上限和下限控制，所以，使用时应根据实际工作高度停机，以避免行程开关多次升降碰撞，而导致损坏。
4、工作螺母安全机构的球座和安全螺母之间的间隙小于7mm时，应立即更换工作螺母，不要全依赖保险机构，使工作螺母全磨损为止。
维护和服务：1、本机应经常擦拭、清理，保持电梯外观清洁。
2、螺旋油缸上下端轴承，应二年润滑一次。
3、导向轮、行走轮应每两周润滑一次。
4、丝缸、螺钉螺母应每周润滑一次。
5、减速机应在两年内加注00号润滑脂一次。
6、每天工作前，应先检查工作螺母保险机构，球座和安全螺母之间的间隙为11±1mm,磨损到7mm以下时，表明工作螺母已严重磨损，应立即更换。
另外还要经常检查上下行程开关，是否动作灵敏、可靠，确保保险机构安全可靠。
7、电磁离合器的摩擦片，应定期检查其磨损情况，发现摩擦片损坏时，应立即更换。
如停机后出现螺母下滑情况，可调离合器弹簧调整螺栓，增加其摩擦力，阻止下滑。
美国JLG升降车说明书
JLG INDUSTRIES, INC. SENDS SAFETY RELATED BULLETINS TO THE OWNER OF RECORD OF THIS MACHINE. CONTACT JLG INDUSTRIES, INC. TO ENSURE THAT THE CURRENT OWNER RECORDS ARE UPDATED AND ACCURATE.
ห้องสมุดไป่ตู้
SECTION - PARAGRAPH, SUBJECT
PAGE
2.2 PREPARATION, INSPECTION, AND MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
2.3 PRE-START INSPECTION. . . . . . . . . . . . . . . . . . . . 2-4 Preparing the Machine for Operation . . . . . . . . . 2-5 Function Check . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
or Your Local JLG Office (See addresses on manual rear cover)
In USA:
Toll Free: 877-JLG-SAFE (877-554-7233)
Outside USA:
Phone: 240-420-2661 E-mail: ProductSafety@
NOTICE
JLG INDUSTRIES, INC. MUST BE NOTIFIED IMMEDIATELY IN ALL INSTANCES WHERE JLG PRODUCTS HAVE BEEN INVOLVED IN AN ACCIDENT INVOLVING BODILY INJURY OR DEATH OF PERSONNEL OR WHEN SUBSTANTIAL DAMAGE HAS OCCURRED TO PERSONAL PROPERTY OR THE JLG PRODUCT.
汽车专用升降机使用操作说明书
真诚感谢使用我公司的机械式停车设备产品，本设备属于汽车专用升降机类机械式停车设备。
为确保您安全和正确使用本设备，特编写此操作使用说明书。
本操作使用说明书详细阐述了汽车专用升降机类机械式停车设备的正确使用方法及注意事项。
不正确的使用不仅会造成设备的不正常运行，还有可能降低产品的寿命或者发生故障，甚至造成严重的后果。
使用本停车设备之前请务必认真阅读此书，充分理解并掌握本设备的操作方法和使用方法。
请务必遵守以下事项：此操作使用说明书阅读后请妥善保管。
安全使用 (3)安全铭牌 (13)设备的运行 (14)停车前确认 (15)可容车尺寸 (16)操作盘名称和用途 (17)紧急停止的方法 (20)机动车入库操作流程 (21)机动车入库的方法 (22)车板上停放机动车 (24)机动车出库操作流程 (26)紧急情况的注意事项 (27)遇到恶劣天气、天灾时需要注意的事项 (29)安全使用操作失误是造成事故与故障发生的主要原因。
在使用之前必须拿到使用说明书、并且要仔细阅读说明书的内容，严格按照指定的使用指导去操作实施。
此使用说明书是针对设备的所有者、管理者、使用者的使用操作说明书。
⏹所有者、管理者从厂家、物业公司接受使用指导、拿到使用说明书。
再针对使用者进行操作指导。
⏹使用者操作方法从所有者、管理者处接受专业的操作指导并拿到操作说明书。
必须仔细阅读操作说明书、理解后方可进行操作。
除了所有者、管理者及接受过专业指导操作过的使用者以外的其他人员，绝对禁止操作。
安全注意（必须遵守）无视所显示的内容错误操作将产生危险程度如下:不遵守“危险”事项，会引发极度危险的状况、可能造成死亡及重伤、以及重大的损失。
不遵守“警告”事项，会引发危险的状况、可能造成死亡及重伤，以及重大的损失。
不遵守“注意”事项，会引发危险的状况、可能造成中度伤害或轻伤以及受损。
以上内容务必理解。
为了能安全地使用设备，务必理解以上内容。
⏹有人时不可操作人在设备里面时绝对不可操作。
汽车升降台的使用方法
汽车升降台的使用方法【知识文章标题】汽车升降台的使用方法：安全与效率的平衡探索【引言】在汽车维修和保养过程中，汽车升降台是一种必不可少的设备。
它不仅能够提供便利的工作环境，还可以提高工作效率。
然而，正确使用汽车升降台并保证安全性却并非易事。
为了在保证效率的同时注重安全，本文将探讨汽车升降台的使用方法。
【正文】1. 什么是汽车升降台？汽车升降台是一种用于举升汽车的设备，它通过液压系统或电动系统，将汽车提升到适合工作的高度，便于进行维修、保养和检查等工作。
常见的汽车升降台有两柱式升降台、四柱式升降台和剪式升降台等。
2. 汽车升降台的安全使用方法正确的使用汽车升降台是确保安全的关键。
下面是一些重要的使用方法和注意事项：（1）检查汽车升降台：在使用升降台之前，应仔细检查设备的各个部分，确保其没有损坏或松动。
特别要注意液压系统或电动系统的正常运转，确保升降台可以稳定地工作。
（2）合理分配承重：在升降台上举升车辆时，要确保车辆的重心均匀分布，避免产生不平衡的状况，以免发生侧翻或倾覆等事故。
（3）固定住车辆：在将车辆放置在升降台上时，应使用固定装置或锁定装置，确保车辆牢固地固定在升降台上，避免在工作过程中出现不稳定的情况。
（4）注意安全间隔：在车辆被举起时，需要保持足够的安全间距，以防止任何部位因意外而被夹伤。
（5）缓慢操作：当操作汽车升降台时，应缓慢且稳定地进行，避免突然操作或快速移动，以确保升降平稳进行。
3. 汽车升降台的效率优化除了安全性，提高工作效率也是使用汽车升降台的关键目标。
下面是一些方法可以帮助提高升降台的效率：（1）熟悉操作：操作者应熟悉汽车升降台的使用步骤和操作要领，以减少操作时间和错误操作。
（2）合理车辆停放：在使用升降台之前，要确保车辆停放在适合举升操作的位置，以免浪费时间和精力。
（3）科学安排工作流程：在进行车辆维修和保养工作时，可以合理安排工作流程，充分利用升降台的能力，提高工作效率。
Jeep JL Wrangler 后车轨梁支架铆盖（支撑4英寸抬高）用户指南说明书
1Jeep JL Rear Track Bar Bracket for 4” LiftInstructions Tools needed:• Basic Mechanics Tool Set • Factory Service Manual •Drill• 1/2” Drill Bits • Pilot Drill Bit • Center Punch • Torque RatchetKit #1953600 Jeep JL Wrangler, Rear Track Bar Bracket 4" LiftImportant Notes:This bracket requires at least a 2” bump stop spacer to prevent damage to the body during sus-pension cycle.Prior to beginning this install, or any installation, read the instructions thoroughly to familiarize yourselfwith the required steps. Evaluate if you are experienced and capable to personally perform these modifi-cations. A factory service manual should be used in conjunction with these installation instructions. This product will change the highway handling characteristics of your vehicle, exercise caution. After altering the suspension it is always advisable to have an alignment done by a competent 4 wheel drive shop or by an alignment shop that is experienced with lifted 4 wheel drive vehicles.Refer to the parts list to ensure that all necessary components and hardware has been included. If any parts are missing please contact your local TeraFlex dealer for assistance.Refer to the factory service manual for the torque specs of the originally equipped hardware.132645126543TIP: For the best results use a center punch and drill apilot hole.Install provided M14 bolt, spacer, and M14 nut into track bar relocation bracket and mount.Torque provided M12 bolts to 95 ft -lbs. [16mm & 18mm] Torque provided M14 bolt to 150 ft -lbs. [18mm & 21mm]。
超级抬高系统 - 杰普汽车悬挂系统调整指南说明书
SUPERLIFT SUSPENSION SYSTEMS300 Huey Lenard Loop Rd.West Monroe, Louisiana 71292Phone: (318) 397-3000Sales / Tech: 1-800-551-4955FAX: (318) 397-3040Superlift adjustable rear track bar forJEEP WRANGLER (TJ)INSTALLATION INSTRUCTIONSINTRODUCTIONInstallation requires a professional mechanic. Prior to beginning, inspect the vehicles steering, driveline, and brake systems, paying close attention to the suspension link arms and bushings, anti-sway bars and bushings, tie rod ends, pitman arm, ball joints and wheel bearings. Also check the steering sector-to-frame and all suspension-to-frame attaching points for stress cracks. The overall vehicle must be in excellent working condition; repair or replace all worn parts.Read instructions several times before starting. Be sure you have all needed parts and know where they install. Read each step completely as you go.NOTES:•The instructions below detail only the installation of the adjustable rear track bar. Refer to the main instruction form supplied with the lift system for all other installation steps.•This track bar only fits vehicles equipped with a 4”-6” lift system and should be compatible with lift systems from most reputable manufacturers.•In addition to the adjustable track bar supplied, any TJ equipped with a 6” lift will also require the track bar bracket supplied with the suspension lift system to be retained. Track bar brackets supplied with a 4” lift system may be removed provided that the maximumadjustment on the Superlift track bar is not exceeded. Otherwise, the bracket supplied with the lift system must be retained.• A foot-pound torque reading is given in parenthesis ( ) after each appropriate fastener.•Do not fabricate any components to gain additional suspension height.•Paint or undercoat all exposed metal surfaces.•Prior to attaching components, be sure all mating surfaces are free of grit, grease, undercoating, etc.• A factory service manual should be on hand for reference.•Use the check-off box “ ” found at each step to help you keep your place. Two “ ”denotes that one check-off box is for the driver side and one is for the passenger side.Unless otherwise noted, always start with the driver side.PARTS LIST … The part number is stamped into each part or printed on an adhesive label. Identify each part and place the appropriate mounting hardware with it.PART NO DESCRIPTION NEW ATTACHING HARDWARE(Qty.- if more than one) (Qty.- if more than one)55-12-5100 ................... a djustable track bar body, rear .... (2) bushing halfsleeve(1)(1) extra-thick washer(2) 1/2” X 2-3/4” bolt(2) 1/2” SAE washer(2) 1/2”nyloc nut(2) spacer(1) heim joint end(1) 3/4” jam nut1) PREPARE VEHICLE...Position the vehicle on a level surface with the front tires pointing straight ahead. Put the vehicle in park or First gear, set the emergency brake, and chock the rear wheels to prevent any possibility of movement. The vehicle should remain on the ground with the suspension “loaded” at normal operating weight to reflect the true ride height.2)FACTORY TRACK BAR REMOVAL…Remove the factory track bar from the vehicle and set aside. Save all hardware for reuse3) TRACK BAR #55-12-5100...Lubricate and install the supplied bushings and sleeves in the upper end of the track bar (55-12-5100). Note that the supplied extra-thick washer should be positioned between thebushing halves in the eye of the bar.Thread the heim joint with the supplied jam nut in the lower end of the track bar. Set the length of the track bar at 32-5/8” measured from eye-to-eye. This will provide a baseline for adjustment.Position the supplied spacers on both sides of the heim joint and then insert the heim end of the track bar into the track bar bracket on the axle. Loosely secure using the factoryhardware.Slide the bushing end of the track bar into the frame bracket and attach using the supplied 1/2” x 2-3/4” bolt and nyloc nut (75).4) TRACK BAR ADJUSTMENT…Position a plumb bob or similar tool against the inside edge of the frame. Measure the distance between the line of the plumb bob and the brake backing plate. Record thismeasurement, then repeat the procedure on the other side.Compare the two measurements recorded in the previous step; the goal is to make them equal:If the driver side measurement is greater than the passenger side, the track bar needs to be shortened. If the passenger side measurement is greater than the driver side, the track bar needs to be lengthened.Disconnect the heim end of the track bar from the vehicle and make the appropriate adjustments. Tighten the jam nut firmly, then reattach the bar to the axle and torque (75).Once installation is complete, test-drive the vehicle and repeat the measuring procedure to verify the adjustments made were correct.NOTE: The maximum amount of adjustment is no more than 3/8” of exposed heim jointthreads as measured from the top of the jam nut.IMPORTANT PRODUCT USE INFORMATIONAs a general rule, the taller a vehicle is, the easier it will roll over. Offset, as much as possible, what is lost in roll over resistance by increasing tire track width. In other words, go “wide” as you go “tall”. Many sportsmen remove their mud tires after winter / hunting season and install ones more appropriate for street driving; always use as wide a tire and wheel combination as possible to enhance vehicle stability.We strongly recommend, because of roll over possibility, that the vehicle be equipped with a functional roll bar and cage system. Seat belts and shoulder harnesses should be worn at all times. Avoid situations where a side rollover may occur.Generally, braking performances and capabilities are decreased when significantly larger / heavier tires and wheels are used. Take this into consideration while driving.Do not add, alter, or fabricate any factory or aftermarket parts to increase vehicle height over the intended height of the Superlift product purchased. Mixing component brands is not recommended.Most states have some type of law limiting vehicle height. The amount of lift allowed, and how the lift may be achieved, varies greatly. Several states offer exemptions for farm or commercially registered vehicles. It is the owner’s responsibility to check state and local laws to ensure that their vehicle will be in compliance.Superlift makes no claims regarding lifting devices and excludes any and all implied claims. Superlift will not be responsible for any altered product or any improper installation or use of our products.We will be happy to answer any questions concerning the design, function, and correct use of our products. IMPORTANT MAINTENANCE INFORMATIONIt is the ultimate buyer’s responsibility to have all bolts / nuts checked for tightness after the first 100 miles and then every 1000 miles. The steering, suspension and driveline systems, along with wheel alignment should be inspected by a qualified professional mechanic at least every 3000 miles.NOTICE TO DEALER AND VEHICLE OWNERAny vehicle equipped with a Superlift lifting device must have the enclosed “Warning to Driver” decal installed on the inside of the windshield or on the vehicle’s dash, within driver’s view. The “Warning to Driver” decal is to act as a constant safety reminder for whoever may be operating the vehicle. The WARRANTY IS VOID unless this decal is in place. INSTALLING DEALER... It is your responsibility to install warning decal and forward these installation instructions to the vehicle owner for review of warnings, product use and maintenance information. Replacement warning decals are available free upon request.These instructions are to be kept with the vehicle registration papers and owners manual for the service life of the vehicle.SUPERLIFT LIMITED LIFETIME WARRANTYSuspension products bearing the Superlift (LKI Ent.) name are warranted for as long as the original purchaser owns the vehicle that the LKI product was originally installed on. This warranty is non-transferable. Warranty covers only the product, no labor, time loss, or freight incurred. Any product that has been abused, altered, incorrectly installed, or used in competition is not covered. Product finish, spring bushings, Polyurethane products, and normal wear is not covered. The LKI product is subject to replacement or repair. No other warranties are expressed or implied. An authorized Superlift dealer must inspect the part in question and confirm that the “Warning to Driver” decal is properly displayed. A copy of the sales invoice is required for warranty consideration.。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
2012吉普大切诺基底盘升降说明书
2012年吉普大切诺基是一款功能强大的SUV，配备了独特的底盘升降系统，为驾驶者提供了更好的操控性和越野能力。
底盘升降系统使得车辆的底盘高度可以根据不同的驾驶条件进行调整，以适应各种路况和行驶需求。
这款车的底盘升降系统分为两个模式：高速模式和低速模式。
高速模式适用于在高速公路上行驶时，可以将车辆的底盘高度降低，以降低风阻，提供更好的稳定性和燃油经济性。
在这种模式下，车辆的悬挂系统会自动调整，使车辆更加贴近地面，并确保驾驶者享受到舒适的驾驶体验。
而低速模式则适用于越野行驶或通过崎岖不平的路面。
在这种模式下，驾驶者可以将车辆的底盘高度提高，以增加通过性和通过障碍物的能力。
系统还可以自动调整车辆的悬挂系统，以提供更好的悬挂行程和减震效果，确保车辆在恶劣路况下的稳定性和舒适性。
底盘升降系统的调整非常简单，驾驶者只需要通过仪表盘上的按钮选择所需的模式即可。
此外，系统还配备了智能感应功能，可以根据车辆的速度和行驶状态自动选择合适的模式。
例如，在高速行驶时，系统会自动调整为高速模式，而在越野行驶时会选择低速模式。
总的来说，2012年吉普大切诺基的底盘升降系统为驾驶者提供了更好的驾驶体验和行驶能力。
无论是在高速公路上还是在崎岖的越野路段上，这个系统都能够根据不同的需求进行调整，确保车辆的稳定性和舒适性。
这使得该车成为一款非常实用和适应性强的SUV。