模具术语翻译
![模具术语翻译](https://img.360docs.net/imgb8/1linsvlpoj9iwk833o1rhjmdvbw5jlml-81.webp)
![模具术语翻译](https://img.360docs.net/imgb8/1linsvlpoj9iwk833o1rhjmdvbw5jlml-32.webp)
模具名词中英文对照表
序号中文名英文名
1 一、水口gate
2 进水位gate location
3 水口形式gate type
4 大水口edge gate
5 细水口pin-point gate
6 水口大小gate size
7 转水口switching gate
8 唧嘴口径sprue diameter
9 二、流道runner
10 热流道hot runner
11 冷流道cold runner
12 唧嘴直流direct sprue gate
13 圆形流道round runner
14 模流分析mold flow analysis
15 流道平衡runner balance
16 热嘴hot sprue
17 热流道板hot manifold
18 发热管cartridge heater
19 探针thermocouples
20 插头connector plug
21 插座connector socket
22 密封/封料seal
23 三、运水water line
24 喉塞line pug
25 喉管tube
26 塑胶管plastic tube
27 快速接头jiffy quick connector plug
28 四、模具零件mold components
29 三板模three-plate mold
模具名词中英文对照表
序号中文名英文名
30 二板模two-plate mold
31 边钉/导边leader pin/guide pin
32 边司/导套bushing/guide bushing
33 顶针板ejector retainer plate
34 托板support plate
35 螺丝screw
36 管钉dowel pin
37 开模槽ply bar score
38 内模管位core/cavity inter-lock
39 顶针ejector pin
40 司筒ejector sleeve
41 司筒针ejector pin
42 推板stripper plate
43 缩呵movable core
44 扣机(尼龙拉勾)nylon latch lock
45 斜顶lifter
46 模胚(架)mold base
47 母模cavity insert
48 公模core insert
49 行位(滑块)slide
50 镶件insert
51 压座/斜鸡wedge
52 耐磨板/油板wedge wear plate
53 压条plate
54 撑头support pillar
55 唧嘴sprue bushing
56 挡板stop plate
57 定位圈locating ring
58 锁扣latch
模具名词中英文对照表
序号中文名英文名
59 扣鸡parting lock set
60 推杆push bar
61 栓打螺丝S.H.S.B
62 顶板ejector plate
63 活动臂lever arm
64 水口司bush
65 垃圾钉stop pin
66 隔片buffle
67 弹弓柱spring rod
68 弹弓die spring
69 镶针pin
70 销子dowel pin
71 波子弹弓ball catch
72 喉塞pipe plug
73 锁模块lock plate
74 斜顶angle from pin
75 斜顶杆angle ejector rod
76 尼龙拉勾parting locks
77 复位键、提前回杆early return bar
78 气阀valves
79 斜导边angle pin
80 模排气parting line venting
81 模总高超出啤机规格mold base shut height
82 模胚原身出料位
cavity direct cut on A-plate,core
direct cut on B-plate.
83 不准用镶件Do not use (core/cavity) insert
84 用铍铜做镶件use beryllium copper insert
85 强度不够insufficient rigidity
86 公差tolerance
87 铜公(电极) copper electrode
动模 Movable Mould Moving Half
定模座板 Fixed Clamp Plate Top Clamping Plate Top Plate
动模座板 Moving Clamp Plate Bottom Clamping Plate Bottom Plate 上模座板 Upper Clamping Plate
下模座板 Lower Clamping Plate
凹模固定板 Cavity-retainer Plate
型芯固定板 Mould Core-retainer Plate
凸模固定板 Punch-retainer Plate
模套 Die Body Die Sleeve Die Blank
支承板 Backing Plate Support Plate
垫块 Spacer Parallel
支架 Ejector Housing Mould Base Leg
模头 Die Head
根据国家标准,以下为部分压铸模具术语的标准翻译。
压力铸造模具 Die-Casting Die
压铸模零部件
定模 Fixed Die Cover Die
定模座板 Fixed Clamping Plate
定模套板 Bolster Fixed Die
动模 Moving Die Ejector Die
动模座板 Moving Clamping Plate
直流道 Sprue
横流道 Runner
内浇口 Gate
模具分类
Injection Mold 注塑模
Plastic Rubber Mould 塑胶模
Rubber Molding 橡胶成形
Hot Chamber Die Casting 热室压铸
Sand Mold Casting 砂模铸造
Extrusion Mold 挤出模
Multi-Cavity Mold 多模穴模具
Stack Mold, Stack Injection Mould 叠层模Plaster Mold 石膏模
Three Plates Mold 三板模
Plain Die 简易模
Pierce Die 冲孔模
Forming Die 成型模
Progressive Die 连续模
Gang Dies 复合模
Shearing Die 剪边模
Cavity Die 型腔模
Riveting Die 铆合模
Compression Molding 压缩成型
Flash Mold 溢流式模具
Extrusion Mold 挤压式模具
Split Mold 分割式模具
Mould Cavity 型腔母模
Mold Core 模芯公模
Large Die Mold 大型模具
Precise Die Mold 精密模具
Complex Die Mold 复杂模具
Foaming Mould 发泡模具
Metal Die 金属模具
Plastic Mold 塑料模具
Press Tool Stamping Die Punch Die 冲压模具Extrusion Die 挤压模具
Graphite Die 石墨模具
流道浇口部分
Runner System 浇道系统
Sprue Cold Material Trap 浇道冷料井Sprue Puller 拉杆
Runner Design 流道设计
Main Runner 主流道
Secondary Runner 次流道
Mould Gate Design 浇口设计
Submarine Gate 潜伏浇口
Tunnel Gate 隧道式浇口
Pinpoint Gate 点浇口
Fan Gate 扇形浇口
Side Gate 侧浇口
Edge Gate 侧缘浇口
Tab Gate 搭接浇口
Film Gate 薄膜浇口
Flash Gate 闸门浇口
Slit Gate 缝隙浇口
Dish Gate 盘形浇口
Diaphragm Gate 隔膜浇口
Ring Gate 环形浇口
Runnerless 无浇道
Sprueless 无射料管方式
Long Nozzle 延长喷嘴方式
Sprue 浇口,溶渣
Insulated Runner Hot Runner 热浇道
Runner Plat 浇道模块
Valve Gate阀门浇口
Slag Well 冷料井
Cold Slag 冷料渣
Sprue Gate 射料浇口,直浇口
Nozzle 射嘴
Sprue Lock Pin 料头钩销(拉料杆)
注塑缺陷
Flash 飞边
Warpage 翘曲
Air Trap 积风
Blush 发赤
Flow Line 流痕
Splay 银纹
Short Shot 短射
Sink Mark 缩痕
Streak 条纹
Void 缩孔
Weld Line 熔接线
Gas Mark 烧焦
Cold Slug 冷斑Delamination 起皮
Burr 毛刺
Flaw Scratch 刮伤
Gloss 光泽
Glazing 光滑
Surface Check 表面裂痕Hesitation 迟滞
注塑工艺
Molding Conditions 成型条件Drying 烘干
Barrel Temperature 料筒温度Melt Temperature 熔化温度Mold Temperature 模具温度Injection Pressure 注塑压力Back Pressure 背压
Injection Speed 注塑速度Screw Speed 螺杆转速Tensile Strength 抗拉强度Tensile Elongation 延伸率Flexural Modulus 弯曲模数Flexural Strength 抗弯强度Shrinkage 收缩率
Regrind Usage 次料使用Moulding 模塑
机械设备
Lathe 车床
Planer 刨床
Miller Milling Machine 铣床
Grinder 磨床
Driller 钻床
Linear Cutting 线切割
Electrical Sparkle 电火花
Welder 电焊机
Punching Machine 冲床
Robot 机械手
Common Equipment 常用设备
EDM Electron Discharge Machining 放电加工3D Coordinate Measurement 三次元量床Boring Machine 搪孔机
Contouring Machine 轮廓锯床
Copy Grinding Machine 仿形磨床
Cylindrical Grinding Machine 外圆磨床
Die Spotting Machine 合模机
Engraving Machine 雕刻机
Engraving E.D.M 雕模放置加工机
Form Grinding Machine 成形磨床
, Graphite Machine 石墨加工机
Horizontal Boring Machine 卧式搪孔机Horizontal Machine Center 卧式加工制造中心Internal Cylindrical Machine 内圆磨床
模具零件
Top Plate 上托板(顶板)
Top Block 上垫脚
Punch Set 上模座
Punch Pad 上垫板
Punch Holder 上夹板
Stripper Pad 脱料背板
Up Stripper 上脱料板
Male Die 公模(凸模)
Feature Die 公母模
Female Die 母模(凹模)
Upper Mold Plate 上模板
Lower Mold Plate 下模板
Die Pad 下垫板
Die Holder 下夹板
Die Set 下模座
Bottom Block 下垫脚
Bottom Plate下托板(底板)
Stripping Plate 内外打(脱料板)
Outer Stripper 外脱料板
Inner Stripper 内脱料板
Lower Stripper 下脱料板
Inner Guiding Post 内导柱
Inner Hexagon Screw 内六角螺钉
Dowel Pin 固定销
Mould Coil Spring 模具弹簧
Lifter Pin 顶料销
Isoheight Sleeve 等高套筒
Pin 销
Lifter Guide Pin 浮升导料销
Guide Pin 导正销
Wire Spring 圆线弹簧
Outer Guiding Post 外导柱
Stop Screw 止付螺丝
Located Pin 定位销
Outer Bush 外导套
Punch 冲头
Insert 入块(嵌入件)
Deburring Punch 压毛边冲子
Groove Punch 压线冲子
Stamped Punch 字模冲子
Round Punch 圆冲子
Special Shape Punch 异形冲子
Bending Block 折刀
Roller 滚轴
Baffle Plate 挡块
Located Block 定位块
Supporting Block for Location 定位支承块Air Cushion Plate 气垫板
Air-Cushion Eject-rod 气垫顶杆
Trimming Punch 切边冲子
Stiffening Rib Punch Stinger 加强筋冲子Ribbon Punch 压筋冲子
Reel-stretch Punch 卷圆压平冲子
Guide Plate 定位板
Sliding Block 滑块
Sliding Dowel Block 滑块固定块Active Plate 活动板
Lower Sliding Plate 下滑块板Upper Holder Block 上压块
Upper Mid Plate 上中间板
Spring Box 弹簧箱
Spring-Box Eject-rod 弹簧箱顶杆Spring-Box Eject-Plate 弹簧箱顶板Bushing Block Liner Bushing 衬套Cover Plate 盖板
Guide Pad 导料块
模具技术用语
各种常用模具成形方式
Accurate Die Casting 精密压铸Powder Forming 粉末成形Calendaring Molding 压延成形Powder Metal Forging 粉末锻造Cold Chamber Die Casting 冷式压铸Precision Forging 精密锻造
Cold Forging 冷锻
Press Forging 冲锻
Compacting Molding 粉末压出成形Rocking Die Forging 摇动锻造Compound Molding 复合成形
Rotary Forging 回转锻造Compression Molding 压缩成形Rotational Molding 离心成形
Dip Mold 浸渍成形
Rubber Molding 橡胶成形Encapsulation Molding 注入成形Sand Mold Casting 砂模铸造Extrusion Molding 挤出成形
Shell Casting 壳模铸造
Foam Forming 发泡成形
Sinter Forging 烧结锻造
Forging Roll 轧锻
Six Sides Forging 六面锻造Gravity Casting 重力铸造
Slush Molding 凝塑成形
Hollow Blow Molding 中空(吹出)成形Squeeze Casting 高压铸造
Hot Chamber Die Casting 热室压铸
Swaging 挤锻
Hot Forging 热锻
Transfer Molding 转送成形
Injection Molding 射出成形
Warm Forging 温锻
Investment Casting 精密铸造
Matched Die Method 对模成形法
Laminating Method 被覆淋膜成形
Low Pressure Casting 低压铸造
Lost Wax Casting 脱蜡铸造
Matched Mould Thermal Forming 对模热成形模Close Mold 合模
Demould 脱模脱模剂
Mould Unloading 开模
Eject 顶出
Tool Change Retooling Die Changing 换模Mould Clamping 锁模
各式模具分类用语
Bismuth Mold 铋铸模
Landed Plunger Mold 有肩柱塞式模具Burnishing Die 挤光模
Landed Positive Mold 有肩全压式模具
Button Die 镶入式圆形凹模
Loading Shoe Mold 料套式模具
Center-Gated Mold 中心浇口式模具
Loose Detail Mold 活零件模具
Chill Mold 冷硬用铸模
Loose Mold 活动式模具
Cold Hobbing 冷挤压制模法
Louvering Die 百叶窗冲切模
Composite Dies 复合模具
Manifold Die 分歧管模具
Counter Punch 反凸模
Modular Mold 组合模具
Double Stack Mold 双层模具
Multi-Cavity Mold 多模穴模具
Electroformed Mold 电铸成形模
Multi-Gate Mold 复式浇口模具
Expander Die 扩径模
Offset Cold Bending Die 双折冷弯模具Extrusion Die 挤出模
Stack Mold, Stack Injection Mould 叠层模Family Mold 反套制品模具
Plaster Mold 石膏模
Blank Through Dies 漏件式落料模
Porous Mold 通气性模具
Duplicated Cavity Plate 复板模
Positive Mold 全压式模具
Fantail Die 扇尾形模具
Pressure Die 压紧模
Fishtail Die 鱼尾形模具
Profile Die 轮廓模
Flash Mold 溢料式模具
Progressive Die 顺序模
Gypsum Mold 石膏铸模
Portable Mold 手提式模具
Hot-Runner Mold 热流道模具
Prototype Mold 雏形试验模具原型模具Ingot Mold 钢锭模
Punching Die 落料模
Lancing Die 切口模切缝模
Raising(Embossing)压花起伏成形
Re-entrant Mold 倒角式模具
Sectional Die 拼合模
Runless Injection Mold 无流道冷料模具Sectional Die 对合模具
Segment Mold 组合模
Semi-Positive Mold 半全压式模具<, /SPAN> Shaper 定型模套
Single Cavity Mold 单腔模具
Solid Forging Die 整体锻模
Split Forging Die 拼合锻模
Split Mold 双并式模具
Sprueless Mold 无注道残料模具
Squeezing Die 挤压模
Stretch Form Die 拉伸成形模
Sweeping Mold 平刮铸模
Swing Die 振动模具
Three Plates Mold 三片式模具
Trimming Die 切边模
Unit Mold 单元式模具
Universal Mold 通用模具Unscrewing Mold 退扣式模具Yoke Type Die 轭型模
模具厂常用之标准零配件
Air Vent Valve 通气阀
Anchor Pin 锚梢
Angular Pin 角梢
Baffle 调节阻板
Angular Pin 倾斜梢
Baffle Plate 折流档板
Ball Button 球塞套
Ball Plunger 定位球塞
Ball Slider 球塞滑块
Binder Plate 压板
Blank Holder 防皱压板
Blanking Die 落料冲头
Bolster 上下模板
Bottom board 浇注底板
Bolster 垫板
Bottom Plate 下固定板
Bracket 托架
Bumper Block 缓冲块
Buster 堵口
Casting Ladle 浇注包
Casting lug 铸耳
Cavity 模穴(模仁)
Cavity Retainer Plate 模穴托板Center Pin 中心梢
Clamping Block 锁定块
Coil Spring 螺旋弹簧
Cold Punched Nut 冷冲螺母Cooling Spiral 螺旋冷却栓Core 心型
Core Pin 心型梢
Cotter 开口梢
Cross 十字接头
Cushion Pin 缓冲梢
Diaphragm Gate 盘形浇口
Die Approach 模头料道
Die Bed 型底
Die Block 块形模体
Die Body 铸模座
Die Bush 合模衬套
Die Button 冲模母模
Die Clamper 夹模器
Die Fastener 模具固定用零件
Die Holder 母模固定板
Die Lip 模唇
Die Plate 冲模板
Die Set 冲压模座
Direct Gate 直接浇口
Dog Chuck 爪牙夹头
Dowel 定位梢
Dowel Hole 导套孔
Dowel Pin 合模梢
Dozzle 辅助浇口
Dowel Pin 定位梢
Draft 拔模锥度
Draw Bead 张力调整杆
Drive Bearing 传动轴承
Ejection Pad 顶出衬垫
Ejector 脱模器
Ejector Guide Pin 顶出导梢
Ejector Leader Bush 顶出导梢衬套Ejector Pad 顶出垫
Ejector Pin 顶出梢
Ejector Plate 顶出板
Ejector Rod 顶出杆
Ejector Sleeve 顶出衬套
Ejector Valve 顶出阀
Eye Bolt 环首螺栓
Filling Core 填充型芯椿入蕊
Film Gate 薄膜形浇口
Finger Pin 指形梢
Finish Machined Plate 角形模板Finish Machined Round Plate 圆形模板Fixed Bolster Plate 固定侧模板Flanged Pin 带凸缘针
Flash Gate 毛边形浇口
Flask 上箱
Floating Punch 浮动冲头
Gate 浇口
Gate Land 浇口面
Gib 凹形拉紧楔
Goose Neck 鹅颈管
Guide Bushing 引导衬套
Guide Pin 导梢
Guide Post 引导柱
Guide Plate 导板
Guide Rail 导轨
Head Punch 顶头冲孔
Headless Punch 直柄冲头
Heavily Tapered Solid 整体模蕊盒Hose Nippler 管接头
Impact Damper 缓冲器
Injection Ram 压射柱塞
Inlay Bush 嵌入衬套
Inner Plunger 内柱塞
Inner Punch 内冲头
Insert 嵌件
Insert Pin 嵌件梢
King Pin 转向梢
King Pin Bush 主梢衬套
Knockout Bar 脱模杵
Land 合模平坦面
Land Area 合模面
Leader Bush 导梢衬套
Lifting Pin 起模顶针起模杆
Lining 内衬
Locating Center Punch 定位中心冲头Locating Pilot Pin 定位导梢Locating Ring 定位环
Lock Block 压块
Locking Block 定位块
Locking Plate 定位板
Loose Bush 活动衬套
Making Die 打印冲子
Manifold Block 歧管档块
Master Plate 靠模样板
Match Plate 分型板
Mold Base 塑胶模座
Mold Clamp 铸模紧固夹
Mold Platen 模用板
Moving Bolster 换模保持装置Moving Bolster Plate 可动侧模板One Piece Casting 整体铸件
Parallel Block 平行垫块
Parting Line 分模线
Parting Lock Set 合模定位器
Pass Guide 穴型导板
Peened Head Punch 镶入式冲头锤击强化冲头钻杆凸模Pilot Pin 定位销导向销子
Pin Gate 针尖浇口
Plate 衬板
Pre Extrusion Punch 顶挤冲头
Punch 冲头
Puncher 推杆
Pusher Pin 衬套梢
Rack 机架
Rapping Rod 起模杆
Re-entrant Mold 凹入模
Retainer Pin 嵌件梢
Retainer Plate 托料板
Return Pin 回位梢
Riding Stripper 浮动脱模器
Ring Gate 环型浇口
Roller 滚筒
Runner 流道
Runner Ejector Set 流道顶出器
Runner Lock Pin 流道拉梢
Screw Plug 头塞
Set Screw 固定螺丝
Shedder 脱模装置
Shim 分隔片
Shoe 模座之上下模板
Shoot 流道
Shoulder Bolt 肩部螺丝
Skeleton 骨架
Slag Riser 冒渣口
Slide(Slide Core)滑块
Slip Joint 滑配接头
Spacer Block 间隔块
Spacer Ring 间隔环
Spider 模蕊支架
Spindle 主轴
Sprue 注道
Sprue Bushing 注道衬套
Sprue Bushing Guide 注道导套
Sprue Lock Bushing 注道定位衬套
Sprue Puller 注道拉料浇道推出杆注道残料顶销Spew Line 合模线
Square Key 方键
Square Nut 方螺帽
Square Thread 方螺纹
Limit Stop Collar 限位套
Stop Pin 止动梢
Stop Ring 止动环
Stopper 定位停止梢
Straight Pin 圆柱销
Stripper Bolt 脱料螺栓
Stripper Bushing 脱模衬套
Stripper Plate 剥料板
Stroke End Block 行程止梢
Submarine Gate 潜入式浇口
Support Pillar 支撑支柱顶出支柱Support Pin 支撑梢
Supporting Plate 托板
Sweep Template 造模刮板
Tab Gate 辅助浇口
Taper Key 推拔键
Taper Pin 拔锥梢锥形梢
Teeming Pouring 浇注
Three Start Screw 三条螺纹
Thrust Pin 推力销
Tie Bar 拉杵
Tunnel Gate 隧道形浇口
Vent 通气孔
Wortle Plate 拉丝模板
模具常用之工作机械
3D Coordinate Measurement 三次元量床Boring Machine 搪孔机
CNC Milling Machine CNC铣床Contouring Machine 轮廓锯床
Copy Grinding Machine 仿形磨床
Copy Lathe 仿形车床
Copy Milling Machine 仿形铣床
Copy Shaping Machine 仿形刨床Cylindrical Grinding Machine 外圆磨床Die Spotting Machine 合模机
Drilling Machine 钻孔机
Engraving Machine 雕刻机
Engraving E.D.M 雕模放置加工机
Form Grinding Machine 成形磨床
Graphite Machine 石墨加工机
Horizontal Boring Machine 卧式搪孔机
Horizontal Machine Center 卧式加工制造中心
Internal Cylindrical Machine 内圆磨床
Jig Boring Machine 冶具搪孔机
Jig Grinding Machine 冶具磨床
Lap Machine 研磨机
Machine Center 加工制造中心
Multi Model Miller 靠磨铣床
NC Drilling Machine NC钻床
NC Grinding Machine NC磨床
NC Lathe NC车床
NC Programming System NC程式制作系统
Planer 龙门刨床
Profile Grinding Machine 投影磨床
Projection Grinder 投影磨床
Radial Drilling Machine 旋臂钻床
Shaper 牛头刨床
Surface Grinder 平面磨床
Try Machine 试模机
Turret Lathe 转塔车床
Universal Tool Grinding Machine 万能工具磨床
Vertical Machine Center 立式加工制造中心
Wire E.D.M 线割放电加工机
入水 Gate
进入位 Gate Location
水口形式 Gate Type
大水口 Edge Gate
细水口 Pin-point Gate
水口大小 Gate Size
转水口 Switching Runner Gate
唧嘴口径 Sprue Diameter
流道 Mold Runner
热流道 Hot Runner Hot Manifold
温度控制器温控器 Thermostat Thermoregulators Temperature Controller 热嘴冷流道 Hot Sprue Cold Runner
唧嘴直流 Direct Sprue Gate
圆形流道 Round Full Half Runner
流道电脑分析 Mold Flow Analysis
流道平衡 Runner Balance
热嘴 Hot Sprue
热流道板 Hot Manifold
发热管 Cartridge Heater
探针 Thermocouples
插头 Connector Plug
插座 Connector Socket
密封封料 Seal
运水 Water Line
喉塞 Line Plug Throat Taps
喉管 Tube
塑胶管 Plastic Tube
快速接头 Jiffy Quick Connector Quick Disconnect Coupling 模具零件 Mold Components
三板模 3-Plate Mold
二板模 2-Plate Mold
边钉导边 Leader Pin Guide Pin
边司导套 Bushing Guide Bushing
中托司 Shoulder Guide Bushing
中托边 Guide Pin
顶针板 Ejector Retainner Plate
托板 Support Plate
螺丝 Screw
管钉 Dowel Pin
开模槽 Ply Bar Scot
内模管位 Core Cavity inter-Lock
顶针 Ejector Pin
司筒 Ejector Sleeve
司筒针 Ejector Pin
推板 Eject Plate Push Plate Stripper Plate
缩呵 Movable Core Return Core Puller
扣机(尼龙拉勾) Nylon Latch Lock
斜顶 Lifter
模胚(架) Mold Base
上内模 Cavity Insert
下内模 Core Insert
行位(滑块) Slide
镶件 Insert
压座 Wedge
耐磨板油板 Wedge Wear Plate
压条 Plate
撑头 Support Pillar
唧嘴 Sprue Bushing
挡板 Stop Plate
定位圈 Locating Ring
锁扣 Latch
扣机 Parting Lock Set
推杆 Push Bar
栓打螺丝 S.H.S.B
顶板 Ejector Plate
活动臂 Lever Arm
分流锥 Sprue Spreader
分流板 Spreader Plate
水口司 Bush
垃圾钉 Stop Pin
隔片 Buffle
弹弓柱 Spring Rod
弹弓 Die Spring
中托司 Ejector Guide Bush
中托边 Ejector Guide Pin
镶针 Pin
销子 Dowel Pin
波子弹弓 Ball catch
喉塞 Pipe Plug
锁模块 Lock Plate
斜顶 Angle from Pin
斜顶杆 Angle Ejector Rod
尼龙拉勾 Parting Locks
活动臂 Lever Arm
复位键提前回杆 Early Return Bar
气阀 Valves
斜导边 Angle Pin
术语 Terms
承压平面平衡 Parting Surface Support Balance
模排气 Parting Line Venting
回针碰料位 Return Pin and Cavity Interference
顶针碰运水 Water Line Interferes with Ejector Pin 料位出上下模 Part from Cavith (Core) Side
不准用镶件 Do Not Use (Core Cavity) Insert 用铍铜做镶件 Use Beryllium Copper Insert
初步模图设计 Preliminary Mold Design
正式模图设计 Final Mold Design
弹弓压缩量 Spring Compressed length
稳定性好 Good Stability Stable
强度不够 Insufficient Rigidity
均匀冷却 Even Cooling
扣模 Sticking
热膨胀 Thermal Expansion
公差 Tolerance
铜公(电极) Copper Electrode
Air Vent Valve 通气阀
Anchor Pin 锚梢
Angular Pin 角梢
Baffle 调节阻板
Angular Pin 倾斜梢
Baffle Plate 折流挡板
Ball Button 球塞套
Ball Plunger 定位球塞
Ball Slider 球塞滑块
Binder Plate 压板
Blank Holder 防皱压板
Blanking Die 落料冲头
Bolster 上下模板
Bottom Board 浇注底板
Bolster 垫板
Bottom Plate 下固定板
Bracket 托架
Bumper Block 缓冲块
Buster 堵口
Casting Ladle 浇注包
Casting Lug 铸耳
Cavity 模腔模穴(模仁)
Cavity Retainer Plate 模穴托板
Center Pin 中心梢
Clamping Block 锁定块
Coil Spring 螺旋弹簧
Cold Punched Nut 冷冲螺母
Cooling Spiral 螺旋冷却栓
Core 心型
Core Pin 心型梢
Cotter 开口梢
Cross 十字接头
模具专业英文术语大全
模具英语专业术语 模具述语 一、入水:gate 进入位: gate location 水口形式:gate type 大水口:edge gate 细水口: pin-point gate 水口大小:gate size 转水口: switching runner/gate 唧嘴口径: sprue diameter 二、流道: runner 热流道: hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道:round(full/half runner 流道电脑分析:mold flow analysis 流道平衡:runner balance 热嘴: hot sprue 热流道板:hot manifold 发热管:cartridge heater 探针: thermocouples 插头: connector plug 插座: connector socket 密封/封料: seal 三、运水:water line 喉塞:line lpug 喉管:tube 塑胶管:plastic tube 快速接头:jiffy quick connector plug/socker 四、模具零件: mold components 三板模:3-plate mold 二板模:2-plate mold 边钉/导边:leader pin/guide pin 边司/导套:bushing/guide bushing 中托司:shoulder guide bushing 中托边L:guide pin 顶针板:ejector retainner plate 托板: support plate 螺丝: screw 管钉:dowel pin 开模槽:ply bar scot 内模管位:core/cavity inter-lock 顶针: ejector pin 司筒:ejector sleeve 司筒针:ejector pin 推板:stripper plate 缩呵:movable core,return core core puller 扣机(尼龙拉勾):nylon latch lock 斜顶:lifter 模胚(架): mold base 上内模:cavity insert 下内模:core insert 行位(滑块): slide 镶件:insert 压座/斜鸡:wedge 耐磨板/油板:wedge wear plate 压条:plate 撑头: support pillar 唧嘴: sprue bushing 挡板:stop plate 定位圈:locating ring 锁扣:latch 扣鸡:parting lock set 推杆:push bar 栓打螺丝:S.H.S.B 顶板:eracuretun 活动臂:lever arm 分流锥:spure sperader 水口司:bush 垃圾钉:stop pin 隔片:buffle 弹弓柱:spring rod 弹弓:die spring 中托司:ejector guide bush 中托边:ejector guide pin 镶针:pin 销子:dowel pin 波子弹弓:ball catch 喉塞: pipe plug
冲压模具专业词汇中英文翻译
Counter bored hole 沉孔 Chamfer 倒斜角 Fillet 倒圆角 padding block垫块 stepping bar垫条 upper die base上模座 lower die base下模座 upper supporting blank上承板 upper padding plate blank上垫板 spare dies模具备品 spring 弹簧 bolt螺栓 document folder活页夹 file folder资料夹 to put file in order整理资料 spare tools location手工备品仓 first count初盘人 first check初盘复棹人 second count 复盘人 second check复盘复核人 equipment设备 waste materials废料 work in progress product在制品 casing = containerization装箱 quantity of physical inventory second count 复盘点数量 Quantity of customs count 会计师盘,点数量 the first page第一联 filed by accounting department for reference会计部存查 end-user/using unit(department)使用单位 Summary of year-end physical inventory bills 年终盘点截止单据汇总表 bill name单据名称 This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department) 本表请与盘点清册一起送会计部-(NHK厂区送财会部) Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用-状况明细表 blank and waste sheet NO. 空白与作废单号
翻译专业术语
Absolute Tran slati on Abstract Tran slati on Abusive tra nslati on Acceptability Accuracy Adaptati on Adequacy Adjustme nt An alogical Form An alysis Applied Tran slati on Studies Architra nseme (ATR) Autonomy Spectrum Autotra nslatio n Back Tran slati on Bilateral in terpret ing Class Shift Close Tran slati on Commu ni cative Tran slati on Commu nity in terpret ing Compe nsati on Compete nee Comp onen tial An alysis Comprehe nsive theory 古阿德克(Gouadec)古阿德克(Gouadec)路易斯(Lewis) 托利(Toury) 罗斯(Rose) 波波维奇(Popovic) 凯斯(Keith) 韩礼德(Halliday)纽马克(Newmark)纽马克(Newmark) 赫维(Hervey) 托利(Toury) 奈达(Nida ) 术语翻译贝献者 绝对翻译 摘要翻译 滥译 可接受性 准确 改编 充分性 调整 类同形式 分析 应用翻译研究 元译素 自立幅度 自译 回译 双边传译 词类转换 贴近翻译 传意翻译;交际翻译 社群传译 补偿 能力 语义成分分析 综合理论 霍尔姆斯(Holmes) 奈达(Nida)和泰伯(Taber) 霍尔姆斯(Holmes) 范路文兹瓦特(van Leuven-Zwart )
机械专业术语英文翻译
陶瓷 ceramics 合成纤维 synthetic fibre 电化学腐蚀 electrochemical corrosion 车架 automotive chassis 悬架 suspension 转向器 redirector 变速器 speed changer 板料冲压 sheet metal parts 孔加工 spot facing machining 车间 workshop 工程技术人员 engineer 气动夹紧 pneuma lock 数学模型 mathematical model 画法几何 descriptive geometry 机械制图 Mechanical drawing 投影 projection 视图 view 剖视图 profile chart 标准件 standard component 零件图 part drawing 装配图 assembly drawing 尺寸标注 size marking
技术要求 technical requirements 刚度 rigidity 内力 internal force 位移 displacement 截面 section 疲劳极限 fatigue limit 断裂 fracture 塑性变形 plastic distortion 脆性材料 brittleness material 刚度准则 rigidity criterion 垫圈 washer 垫片 spacer 直齿圆柱齿轮 straight toothed spur gear 斜齿圆柱齿轮 helical-spur gear 直齿锥齿轮 straight bevel gear 运动简图 kinematic sketch 齿轮齿条 pinion and rack 蜗杆蜗轮 worm and worm gear 虚约束 passive constraint 曲柄 crank 摇杆 racker 凸轮 cams
模具术语英文翻译知识讲解
模具术语英文翻译
模具术语英文翻译 根据国家标准,以下为部分塑料模具成形术语的标准翻译。 动模 Movable Mould Moving Half 定模座板 Fixed Clamp Plate Top Clamping Plate Top Plate 动模座板 Moving Clamp Plate Bottom Clamping Plate Bottom Plate 上模座板 Upper Clamping Plate 下模座板 Lower Clamping Plate 凹模固定板 Cavity-retainer Plate 型芯固定板 Mould Core-retainer Plate 凸模固定板 Punch-retainer Plate 模套 Die Body Die Sleeve Die Blank 支承板 Backing Plate Support Plate 垫块 Spacer Parallel 支架 Ejector Housing Mould Base Leg 模头 Die Head 根据国家标准,以下为部分压铸模具术语的标准翻译。 压力铸造模具 Die-Casting Die 压铸模零部件 定模 Fixed Die Cover Die 定模座板 Fixed Clamping Plate 定模套板 Bolster Fixed Die 动模 Moving Die Ejector Die 动模座板 Moving Clamping Plate 直流道 Sprue 横流道 Runner 内浇口 Gate 模具分类 Injection Mold 注塑模 Plastic Rubber Mould 塑胶模 Rubber Molding 橡胶成形 Hot Chamber Die Casting 热室压铸 Sand Mold Casting 砂模铸造 Extrusion Mold 挤出模 Multi-Cavity Mold 多模穴模具 Stack Mold, Stack Injection Mould 叠层模
机械专业外文翻译中英文翻译
外文翻译 英文原文 Belt Conveying Systems Development of driving system Among the methods of material conveying employed,belt conveyors play a very important part in the reliable carrying of material over long distances at competitive cost.Conveyor systems have become larger and more complex and drive systems have also been going through a process of evolution and will continue to do so.Nowadays,bigger belts require more power and have brought the need for larger individual drives as well as multiple drives such as 3 drives of 750 kW for one belt(this is the case for the conveyor drives in Chengzhuang Mine).The ability to control drive acceleration torque is critical to belt conveyors’ performance.An efficient drive system should be able to provide smooth,soft starts while maintaining belt tensions within the specified safe limits.For load sharing on multiple drives.torque and speed control are also important consideratio ns in the drive system’s design. Due to the advances in conveyor drive control technology,at present many more reliable.Cost-effective and performance-driven conveyor drive systems cov ering a wide range of power are available for customers’ choices[1]. 1 Analysis on conveyor drive technologies 1.1 Direct drives Full-voltage starters.With a full-voltage starter design,the conveyor head shaft is direct-coupled to the motor through the gear drive.Direct full-voltage starters are adequate for relatively low-power, simple-profile conveyors.With direct fu11-voltage starters.no control is provided for various conveyor loads and.depending on the ratio between fu11- and no-1oad power requirements,empty starting times can be three or four times faster than full load.The maintenance-free starting system is simple,low-cost and very reliable.However, they cannot control starting torque and maximum stall torque;therefore.they are
常用模具零件中英文对照表
常用模具零件中英文对照表 2005-12-19 14:51:17???中国注塑网 入水:gate 进入位:gate location 水口形式:gate type 大水口:edge gate 细水口: pin-point gate 水口大小:gate size 转水口:switching runner/gate 唧嘴口径:sprue diameter 二、流道: runner 热流道:hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道:round(full/half runner 流道电脑分析:mold flow analysis :?[??n?l?s?s] 流道平衡:runner balance 热嘴:hot sprue 热流道板:hot manifold 发热管:cartridge heater 探针: thermocouples 插头:connector plug 插座: connector socket 密封/封料: seal 三、运水:water line 喉塞:line lpug 喉管:tube 塑胶管:plastic tube 快速接头:jiffy quick connector plug/socker 四、模具零件:mold components 三板模:3-plate mold 二板模:2-plate mold 边钉/导边:leader pin/guide pin 边司/导套:bushing/guide bushing 中托司:shoulder guide bushing 中托边:guide pin 顶针板:ejector retainer plate 托板:support plate
机械术语英文翻译
机械术语英文翻译 阿基米德蜗杆Archimedes worm 安全系数safety factor; factor of safety安全载荷safe load 凹面、凹度concavity扳手wrench 板簧flat leaf spring 半圆键woodruff key 变形deformation摆杆oscillating bar 摆动从动件oscillating follower 摆动从动件凸轮机构cam with oscillating follower 摆动导杆机构oscillating guide-bar mechanism 摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile 摆线运动规律cycloidal motion 摆线针轮cycloidal-pin wheel包角angle of contact 保持架cage背对背安装丨back-to-back arrangement 背锥back cone ;normal cone 背锥角back angle背锥距back cone distance比例尺scale 热容specific heat capacity 闭式链closed kinematic chain闭链机构closed chain mechanism 臂部arm 变频器frequency converters变频调速frequency control of motor speed 变速speed change 变速齿轮change gear ; change wheel变位齿轮modified gear变位系数modification coefficient 标准齿轮standard gear标准直齿轮standard spur gear 表面质量系数superficial mass factor 表面传热系数surface coefficient of heat transfer 表面粗糙度surface roughness 并联式组合combination in parallel并联机构parallel mechanism 并联组合机构parallel combined mechanism并行工程concurrent engineering 并行设计concurred design, CD不平衡相位phase angle of unbalance 不平衡imbalance (or unbalance)不平衡量amount of unbalance 不完全齿轮机构intermittent gearing波发生器wave generator 波数number of waves补偿compensation 参数化设计parameterization design, PD残余应力residual stress 操纵及控制装置operation control device槽轮Geneva wheel 槽轮机构Geneva mechanism ;Maltese cross槽数Geneva numerate 槽凸轮groove cam侧隙backlash 差动轮系differential gear train差动螺旋机构differential screw mechanism 差速器differential常用机构conventional mechanism; mechanism in common use 车床lathe承载量系数bearing capacity factor 承载能力bearing capacity成对安装paired mounting 尺寸系列dimension series齿槽tooth space 齿槽宽spacewidth齿侧间隙backlash 齿顶高addendum齿顶圆addendum circle 齿根高dedendum齿根圆dedendum circle 齿厚tooth thickness齿距circular pitch 齿宽face width齿廓tooth profile 齿廓曲线tooth curve齿轮gear 齿轮变速箱speed-changing gear boxes齿轮齿条机构pinion and rack 齿轮插刀pinion cutter; pinion-shaped shaper cutter齿轮滚刀hob ,hobbing cutter 齿轮机构gear齿轮轮坯blank 齿轮传动系pinion unit齿轮联轴器gear coupling 齿条传动rack gear齿数tooth number 齿数比gear ratio齿条rack 齿条插刀rack cutter; rack-shaped shaper cutter齿形链、无声链silent chain 齿形系数form factor齿式棘轮机构tooth ratchet mechanism 插齿机gear shaper重合点coincident points 重合度contact ratio冲床punch
模具DFM常用中英文对照
DFM常用中英文对照 1、这个红色面在前模方向/后模方向/行位方向有倒扣。 This red surface is undercut at cavity side / core side / slider side. 2、这些红色面在前模方向/后模方向/行位方向有倒扣。 These red surfaces are undercut at cavity side / core side / slider side. 3、产品的这个位置太小,导致模具在前模方向/后模方向/行位方向有薄钢位。 This position is too small and it will bring the thin steel at cavity side / core side / slider side. 4、这些红色线是前后模/镶件/行位/斜顶分型线。 These red lines are the parting line of cavity and core / insert / slider / lifter. 5、此产品使用推板/推块顶出。 Use the stripper plate / ejector block to eject this part. 6、前模/后模斜内行位。 Inner angle slider at cavity / core side. 7、为了简化模具结构建议改变此处出模方向。 Suggest to change the draft direction of this position to make the mold structure simply. 8、最终的进胶位置根据模流分析。 Finally gate position according the mold flow analysis. 9、斜顶与后面的柱位空间太小,斜顶在运动时会干涉到柱子,请考虑移动这个柱子的位置。 This lifter intervene with the pole during ejection, please consider changing the position of the pole. 10、此处有薄钢位,强度不足而且不容易冷却。 The strength of this area is too weak and it is hard to cool because the thin steel. 11、此处有尖角,填充困难。 It is hard to fill for this area because the sharp feature. 12、此处料位太厚,会有缩水,建议减胶改善。 We suggest to reduce some wall thickness to avoid the sink mark for this position. 13、此处的行位夹线在外观面上,请确认是否接受? Please confirm whether it is acceptable to have a slider line on the visible surface? 14、建议加大拔模角,以便脱模顺利。 We suggest to enlarge the draft angle to help release the tool. 15、如果分型面此处,模具上会有尖角和刀口,对模具寿命有影响。 There are sharp edges if we set the parting line here, it will reduce the tool life. 16、此处料厚段差很大,成品表面会有应力痕,建议修改如图示。 The thickness is not equal and it will bring the stress lines on the surface, suggest to improve the part as the picture shown. 17、此大行位上有小行位,开模时小行位需先退,大行位做延时,合模时则相反。 The small slider is inside the big slider, when the mold open, the small slider need to recede first and the big slider have to postpone. When the mold close, it is contrary. 18、此处需做强顶。 This position need to force ejection. 19、由于此处没有足够空间下热咀,所以需做一个柱子进胶。 This position need to make a pole for gating because there have no enough space for hot sprue. 20、沾模, stick
机械专业相关词汇中英文翻译大全
机械专业相关词汇中英文翻译大全 单价unit price 工日合计Man-day total/work-day total 人工费cost of labor 材料费materials expenses 机械的mechanical 检查接线connection test 发电机generator 调相机phase regulator 周波cycle 减负荷装置 load-shedding equipment 断路器柜circuit breaker cabinet 单母线single busbar 互感器transformer 每相电流Current by Phase 封闭式插接close type socket joint 发电机控制面板generator control panel 分级卸载sorted unloading 同步控制synchronization control 调速器 speed governor 信号屏signal screen 继电器relay 高压柜high pressure cabinet 油浸电力变压器oil-immersed power transformer 空气断路器air circuit breaker 控制屏control panel 直流馈电屏direct current feed control panel 电容器electric condenser 计量盘metering panel 成套配电箱whole set of distribution box 落地式floor model 控制开关Control switches 铜芯电力电缆Copper core power cable 控制电缆actuating cable 热缩式电力电缆终端头pyrocondensation power cable terminal 钢结构支架配管steel structure bracket tubing 万用槽钢versatile U-steel 电缆托架 cable bracket 钢制托盘式桥架steel Tray-type cable support system waterproof socket 防水插座 防爆插座Explosion-proof socket 接地绞线earthing twisted pair 接地母线 earthing bus
翻译术语
Lecture 2 Basic Concepts in Translatology 翻译学基本用语: 源语/译出语source language(SL), original language 译语/译入语target language(TL), receptor language, receiving language 原作者SL author, original author 译者(笔译者)translator 译者(口译者)interpreter 读者/接受者reader, receptor, audience 文本text 原文/原著source text (ST), SL text, original text, original version/original work 译文target text, translation, target version, rendering, rendition 译本/译著translated text/translational work 源语读者source-language reader/SL reader 源语文化source-language culture/source culture 译语读者target-language reader/TL reader/receiving audience 译语文化target-language culture/target culture/receiving
culture 语境context 笔译written translation 口译oral interpretation/oral translation/interpreting 同声传译simultaneous interpreting 交替口译consecutive interpreting 翻译原则translation principle 标准translation criterion (复数形式为criteria) 翻译过程translation process 翻译程序/步骤translation procedures 反应/读者反应response/reader’s response 对应(部分对应/完全对应)(partial /full )correspondence 等值/对等equivalence 对等物(词语)equivalent 形式对等formal equivalence 功能对等functional equivalence 动态对等dynamic equivalence 等效equivalent effect 充分性adequacy 可接受性acceptability(acceptable, unacceptable, unacceptability) 可读性readability(readable)
模具术语翻译
模具名词中英文对照表序号中文名英文名 1一、水口gate 2进水位gate location 3水口形式gate type 4大水口edge gate 5细水口pin-point gate 6水口大小gate size 7转水口switching gate 8唧嘴口径sprue diameter 9二、流道runner 10热流道hot runner 11冷流道cold runner 12唧嘴直流direct sprue gate 13圆形流道round runner 14模流分析mold flow analysis 15流道平衡runner balance 16热嘴hot sprue 17热流道板hot manifold 18发热管cartridge heater 19探针thermocouples 20插头connector plug 21插座connector socket 22密封/封料seal 23三、运水water line 24喉塞line pug 25喉管tube 26塑胶管plastic tube 27快速接头jiffy quick connector plug 28四、模具零件mold components 29三板模three-plate mold 模具名词中英文对照表 序号中文名英文名 30二板模two-plate mold 31边钉/ 导边leader pin /guide pin
32边司/ 导套bush in g/guide bush ing 33顶针板ejector retainer plate 34托板support plate 35螺丝screw 36管钉dowel pin 37开模槽ply bar score 38内模管位core/cavity inter-lock 39顶针ejector pin 40司筒ejector sleeve 41司筒针ejector pin 42推板stripper plate 43缩呵movable core 44扣机(尼龙拉勾)n yl on latch lock 45斜顶lifter 46模胚(架)mold base 47母模cavity in sert 48公模core insert 49行位(滑块)slide 50 镶件in sert 51压座/斜鸡wedge 52耐磨板/ 油板wedge wear plate 53压条plate 54撑头support pillar 55唧嘴sprue bushing 56挡板stop plate 57定位圈locating ring 58锁扣latch 模具名词中英文对照表 序号中文名英文名 59扣鸡parti ng lock set 60推杆push bar 61栓打螺丝S.H.S.B 62顶板ejector plate 63活动臂lever arm
机械专业术语英文翻译
机械专业英语词汇 陶瓷ceramics 合成纤维synthetic fibre 电化学腐蚀electrochemical corrosion 车架automotive chassis 悬架suspension 转向器redirector 变速器speed changer 板料冲压sheet metal parts 孔加工spot facing machining 车间workshop 工程技术人员engineer 气动夹紧pneuma lock 数学模型mathematical model 画法几何descriptive geometry 机械制图Mechanical drawing 投影projection 视图view 剖视图profile chart 标准件standard component 零件图part drawing 装配图assembly drawing 尺寸标注size marking 技术要求technical requirements 刚度rigidity 内力internal force 位移displacement 截面section 疲劳极限fatigue limit 断裂fracture 塑性变形plastic distortion 脆性材料brittleness material 刚度准则rigidity criterion 垫圈washer 垫片spacer 直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear 直齿锥齿轮straight bevel gear 运动简图kinematic sketch 齿轮齿条pinion and rack 蜗杆蜗轮worm and worm gear 虚约束passive constraint 曲柄crank
翻译概论术语整理
1.Source-oriented translation studies 翻译研究趋势有两个维度,一个方面就是坚持面向原文本的程度,另一方面聚焦于语言和产生的译本。以原文本为导向的是传统的规定性翻译研究的显著特征。从原文本的视角分析翻译,把翻译视作语言文字间的转化,却忽视了文化语境。书中有提到一个三角图,三角图的底线最左端代表原文本,最右端代表目标文本,左侧边代表原文本导向,右侧边代表目标文本导向。最左端角过度强调原文本,以至很难区分翻译和直译的区别。在现实中这种情况不常发生。图中显示Catford的形式对等,Nida的动态对等,Koller的语用对等,Beaugrande 基于文本的对等,以及Venuti的异化和对等都属于面向原文本的翻译研究。 2.Formal equivalence Catford把翻译界定为“用目的语(TL)中对等的文本材料取代原语(SL)的文本材料,并把追求原语的等值成分视作翻译的中心问题,从而提出翻译理论的使命就是在于确定等值成分的本质和条件。形式对应指任何译语范畴在译语的“机体”中尽可能占有与该原语范畴在原语中占有同等地位。例如:用一个形容词翻译另一个形容词。形式对应涉及原文本的语言形式,将原语中的结构形式原封不动地照搬入目的语,以原语为中心,最大限度显示原文中的形式与内容。 3.Translation shifts 当无法遵守原文本的语言形式进行翻译操作时,文本对应通过Catford所述的翻译转换所形成。当这两者概念发生分歧时,翻译转换尤其重要,其指从原语到译语的过程中偏离形式对应。设计两种主要的转换:层次转化和范畴转换。在层次转换中,位于一个语言层次的原语文本在译语的另一个层次中找到翻译对等。翻译中唯一的层次转换是语法-词汇转换。例如,原文本的文字游戏可能是通过利用目标语词汇层面进行翻译从而在语音层面得以实现,。范畴转换是通用术语,指翻译偏离形式对等。其分为四类:结构,类别,系统,单元转换。例如,原文本的形容词短语在目标文本变成副词短语。 4.Dynamic equivalence 动态对等指将原文本信息翻译成接受者语言时,译语读者和原语读者的心里反应要极为相似。主张翻译不必受原语中语言形式的各种束缚,在接受语中要考虑读者的反应,翻译要在内容上与原语内容对等,主张翻译就是意译,旨在达到完全对等的表达。在动态对等翻译中,译者关注的并非原语信息和译语信息之间的一一对应,而是译语接受者和译语信息之间的关系应该与原语读者和原文信息之间的关系基本相同。动态对等包括以下程序:1.用更适合的目标语言文化材料替代较难接近的原语项目。2. 引用原文本中含蓄地内容使其在目标语言中更加明确3. 为便于理解控制表达的冗长。 5.Target-oriented translation studies 指翻译研究的趋势转向于以目的文本为导向的翻译研究,焦点在语言和译本,且随着研究的进程研究范围会越来越广。具体可以体现在将翻译研究作为整体的一个三角图,在这个三角图中,自下而上的研究研究范围会越来越狭窄,然而自上而下的研究所涉及领域则越来越广。因而,不再是以往的从语言学的角度研究文本类型和功能,以目的文本为导向的翻译研究开始逐渐转向目的语的文化领域,其中包括不同历史时期的不同价值,意识形态,组织惯例的研究。
模具英语翻译大全
1. The undercut area where interfere with slide block need to be filled material to help the slide can move smoothly.(和滑塊干涉的倒勾請加料填平至滑塊可以順利滑動) 2. The thickening added too thick.(加肉太多) 3. The thickening area is too wide.(加肉面積太大) 4. Gate position is moved.(GATE位置移位) 5. The split line of slide block or the area of slide.(滑塊拆的位置) 6. This area is hard to be filled due to the sharp feature(此處有尖角,填充困難) 7. The strength of this area is too weak and isn’t easy to get c old due to the steel too thin. 8. ( 此處鋼材太薄,強度不足而且不容易冷卻) 9. .The semicircle of cylinder avoids designing on slide block lest it will be pulled apart or cause drag mark. 10. ( 圓柱特徵要有一半圓不可以拆在滑塊上,以免粘滑塊造成拉白,拉斷.) 11. The part will be damaged if we make lifter in this area. 12. ( 此處做斜銷在作動時會削到成品肉厚) 13. This is critical surface where is not allow to add material. 14. ( 這個面是裝配面,不能加料) 15. This thick wall area might because sink mark,Please reduce some wall thickness to improve it.) 16. ( 此處料位太厚,會有縮水,建議減料改善) 17. Please confirm whether it is critical surface or not. Please confirm whether it is acceptable to has Slide split line if we have slide in this area. 18. (此面是不是外觀面,此處做滑塊的話會有結合線,是否可以接受) 19. Please confirm whether we can reduce material to the area where have undercut as indicated to have shut off on core and cavity side. No slide block and lifter to be made. 20. (此處有倒勾,能否減料,使公母模靠破,不做滑塊和斜銷) 21. Please confirm the issues of Parting line, Gate position...Etc otherwise the lead-time will be extended. 22. (請盡快確認這種拆模方式和結構,否則會影響模期) 23. The trim mark of the gate is not visual after open the top case if the gate position is design ed like it 24. (GATE做在此處的話.蓋子打開後看不到GATE的修剪部位) 25. We would suggest to enlarging draft to help tool released.) 26. 加大拔模角,以便脫模順利) 27. There are sharp edges if set the parting line at here, It will reduce the tool life 28. (P.L面開在此處,模具上會有尖角和刀口,對模具壽命有影響) 29. If you insist that the gate position have to be as original design then we would