模具专业翻译
模具术语相关翻译
模具,冲压相关英语专业翻译模具工程常用词汇金属弹片(锅仔片)，metal dome.die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die 连续模compound die复合模punched hole冲孔panel board镶块to cut edges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line strenching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔∙forming成型(抽凸,冲凸)∙draw hole抽孔∙bending折弯∙trim切边∙emboss凸点∙dome凸圆∙semi-shearing半剪 tamp mark冲记号∙deburr or coin压毛边∙punch riveting冲压铆合∙side stretch侧冲压平∙reel stretch卷圆压平∙groove压线∙blanking下料∙stamp letter冲字(料号)∙shearing剪断∙tick-mark nearside正面压印∙tick-mark farside反面压印∙冲压名称类∙stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑common vocabulary for die engineering extension dwg展开图o procedure dwg工程图o die structure dwg模具结构图o material材质o material thickness料片厚度o factor系数o upward向上o downward向下o press specification冲床规格o die height range适用模高o die height闭模高度o burr毛边o gap间隙o weight重量o total wt.总重量o punch wt.上模重量二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝： screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）： mold base上内模：cavity insert下内模：core insert行位（滑块）： slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴： sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die springblooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折迭straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小)cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤(Flow Line)流痕(Weld Line) 熔接线Sink Mark凹陷Streak条纹Warpage翘曲。
模具术语翻译
模具名词中英文对照表序号中文名英文名1 一、水口gate2 进水位gate location3 水口形式gate type4 大水口edge gate5 细水口 pin-point gate6 水口大小gate size7 转水口switching gate8 唧嘴口径sprue diameter9 二、流道runner10 热流道hot runner11 冷流道cold runner12 唧嘴直流direct sprue gate13 圆形流道round runner14 模流分析mold flow analysis15 流道平衡runner balance16 热嘴hot sprue17 热流道板hot manifold18 发热管cartridge heater19 探针thermocouples20 插头connector plug21 插座 connector socket22 密封/封料 seal23 三、运水water line24 喉塞line pug25 喉管tube26 塑胶管plastic tube27 快速接头jiffy quick connector plug28 四、模具零件mold components29 三板模three-plate mold模具名词中英文对照表序号中文名英文名30 二板模two-plate mold31 边钉/导边leader pin/guide pin32 边司/导套bushing/guide bushing33 顶针板ejector retainer plate34 托板support plate35 螺丝 screw36 管钉dowel pin37 开模槽ply bar score38 内模管位core/cavity inter-lock39 顶针ejector pin40 司筒ejector sleeve41 司筒针ejector pin42 推板stripper plate43 缩呵movable core44 扣机（尼龙拉勾） nylon latch lock45 斜顶lifter46 模胚（架） mold base47 母模cavity insert48 公模core insert49 行位（滑块） slide50 镶件insert51 压座/斜鸡wedge52 耐磨板/油板wedge wear plate53 压条plate54 撑头support pillar55 唧嘴 sprue bushing56 挡板stop plate57 定位圈locating ring58 锁扣latch模具名词中英文对照表序号中文名英文名59 扣鸡parting lock set60 推杆push bar61 栓打螺丝S.H.S.B62 顶板ejector plate63 活动臂lever arm64 水口司bush65 垃圾钉stop pin66 隔片buffle67 弹弓柱spring rod68 弹弓die spring69 镶针pin70 销子dowel pin71 波子弹弓ball catch72 喉塞pipe plug73 锁模块lock plate74 斜顶angle from pin75 斜顶杆angle ejector rod76 尼龙拉勾parting locks77 复位键、提前回杆early return bar78 气阀valves79 斜导边angle pin80 模排气parting line venting81 模总高超出啤机规格mold base shut height82 模胚原身出料位cavity direct cut on A-plate，coredirect cut on B-plate.83 不准用镶件Do not use (core/cavity) insert84 用铍铜做镶件use beryllium copper insert85 强度不够insufficient rigidity86 公差tolerance87 铜公(电极) copper electrode动模 Movable Mould Moving Half定模座板 Fixed Clamp Plate Top Clamping Plate Top Plate动模座板 Moving Clamp Plate Bottom Clamping Plate Bottom Plate 上模座板 Upper Clamping Plate下模座板 Lower Clamping Plate凹模固定板 Cavity-retainer Plate型芯固定板 Mould Core-retainer Plate凸模固定板 Punch-retainer Plate模套 Die Body Die Sleeve Die Blank支承板 Backing Plate Support Plate垫块 Spacer Parallel支架 Ejector Housing Mould Base Leg模头 Die Head根据国家标准，以下为部分压铸模具术语的标准翻译。
模具专业术语-中英文对照
Female Die 母模（凹模） Binder Plate 压板
Flask 上箱
Upper Mold Plate 上模板 Blank Holder 防皱压板 Floating Punch 浮动冲头
Lower Mold Plate 下模板 Blanking Die 落料冲头 Gate 浇口
Die Pad 下垫板
Parting Line 分模线
滑块板
Upper Holder Block 上压 Ejector Guide Pin 顶出 Parting Lock Set 合模定
块
导梢
位器
Upper Mid Plate 上中间 Ejector Leader Bush 顶 Pass Guide 穴型导板
板
出导梢衬套
Die Button 冲模母模
Locating Center Punch
定位中心冲头
Die Clamper 夹模器
Locating Pilot Pin 定位
导梢
Die Fastener 模具固定用 Locating Ring 定位环
零件
Die Holder 母模固定板 Lock Block 压块
Roller 滚轴
Located Pin 定位销
Diaphragm Gate 盘形浇口 Knockout Bar 脱模杵
Outer Bush 外导套
Die Approach 模头料道 Land 合模平坦面
Punch 冲头
Die Bed 型底
Land Area 合模面
Insert 入块（嵌入件） Deburring Punch 压毛边 冲子 Groove Punch 压线冲子
Isoheight Sleeve 等高套 Cold Punched Nut 冷冲螺 Inlay Bush 嵌入衬套
模具术语英文翻译
三、模具塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plate Top plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板support plate方铁spacer plate底针板ejector plate面针板ejector retainer plate回针Return pin导柱Guide pin有托导套Shoulder Guide bush 直导套Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate 凸模固定板punch-retainer plate 顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould动模movable mould, movable half上模upper mould，upper half下模lower mould，lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具interchangeable cavity mould 脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine[此文档可自行编辑修改，如有侵权请告知删除，感谢您的支持，我们会努力把内容做得更好]。
模具专业英语翻译
单词翻译：PlasticsCompression Molding for PlasticsTransfer Molding and Injection MoldingPressure Die Casting DiesForging DieFundamental of Chip-type Machining ProcessesFundamental of T urning and Boring on LatheMillingElectrodischarge Machines翻译划线的部分T urning is the process of machining external cylindrical and conical surfaces. It is usually performed on a lathe.The depth of cut (DOC), d, represents the third dimension.As the plastic is fed to the rotating screw, it passes through thre e zones as shown: feed, compression, and metering（定量）.句子翻译The molds used for compression molding are classified into four basic types, namely, positive molds, landed positive molds, flash-type molds, and semipositive molds.In order to harden and eject thermoplastic parts from the mold, cooling would be necessary.There are seven basic chip formation processes: shaping, turning, milling, drilling, sawing, broaching, and grinding (abrasive machining).In the injection mold, The screw（螺杆）acts as a combination injecting and plasticizing unit .The physcal composition of the workpiece greatly influences the selection of the machining method, the tool composition and geometry, and the rate of material removal.The clamping force that a machine is capable of exerting is part of the size designation and is measured in tons.Proper selection of the die material and of the die manufacturing technique determines, to a large extent, the useful life of forging dies.In compression molding the plastic material as powder or performs is placed into a heated steel mold cavity.The guide pins, or posts, are mounted in the lower shoe.Plastic often contain other added materials called fillers.When applying the electrical discharge machining process, the material is eroded as a result of electrical discharge between tool and work.Parts made by transfer molding have greater strengths, more uniform densities, closer dimensional tolerances, and the parting line requires less cleaning as compared with parts made by compression molding.The die blocks contain the movement mechanisms of the die and the inserts incorporating the casting form so that the assembly can be mounted between the tie bars of the machine.In the early dawn civilization mankind discovered that a heated piece of metal was more easily hammered into different shapes.The tools necessary to produce a given forging cannot be made until the shape of the final forging has been determined.Solid models eliminate most of the problems of the wire frame.1.This process of annealing consists of heating the steel to an elevated temperature fora definite period of time and, usually, cooling it slowly.The pattern is a replica of the part being made but has slightly larger dimensions to allow for shrinkage during solidification and cooling of the casting.This type of mold is widely used because it is comparatively easy to construct and it controls thickness and density within close limits..1.If the surface is unusually hard, the cutting speed on the first roughing cut should bereduced accordinglyWelding is a process in which two materials, usually metals, are permanently jointed together through localized coalescence, resulting from a suitable combination of temperature, pressure and metallurgical conditions.汉译英传递模注射模自由锻Smith forging切削加工过程段落翻译After the feed zone, the screw flight depth is gradually reduced, forcing the plastic to compress. The work is converted to heat by shearing the plastics, making ita semifluid（半流体）mass.In the metering zone, additional heat is applied by conduction from the barrel surface. As the chamber in front of the screw becomes filled, it force the screw back, tripping a limit switch that activates a hydraulic cylinder that force the screw forward and injects the fluid plastic into the close mold.Gas tungsten arc welding is performed with the heat from an electric arc discharged between the workpiece and a nonconsumable（不熔化）electrode made of tungsten.This process, like GNA W(gas metal arc welding), is gas-shielded arc welding, where an atmosphere of inert gas is maintained around the arc and no flux（熔剂）is used.The process is often called tungsten inert（惰性）gas welding.。
模具词汇英语翻译汇总特全
模具词汇英语翻译汇总特全burnishingdie挤光模landedpositivemold有肩全压式模具buttondie镶入式圆形凹模loadingshoemold料套式模具center-gatedmold中心浇口式模具loosedetailmold活零件模具chillmold冷硬用铸模loosemold活动式模具clodhobbing冷挤压制模louveringdie百叶窗冲切模compositedies复合模具manifolddie分歧管模具counterpunch反凸模modularmold组合式模具doublestackmold双层模具multi-cavitymold多模穴模具electroformedmold电铸成形模multi-gatemold复式浇口模具expanderdie扩径模offswtbendingdie双折冷弯模具extrusiondie挤出模palletizingdie叠层模familymold反套制品模具plastermold石膏模blankthroughdies漏件式落料模porousmold通气性模具duplicatedcavityplate复板模positivemold全压式模具fantaildie扇尾形模具pressuredie压紧模fishtaildie鱼尾形模具profiledie轮廓模flashmold溢料式模具progressivedie顺序模gypsummold石膏铸模protablemold手提式模具hot-runnermold热流道模具prototypemold雏形试验模具ingotmold钢锭模punchingdie落料模lancingdie切口模raising(embossing)压花起伏成形re-entrantmold倒角式模具sectionaldie拼合模runlessinjectionmold无流道冷料模具sectionaldie对合模具segmentmold组合模semi-positivemold半全压式模具shaper定型模套singlecavitymold单腔模具solidforgingdie整体锻模splitforgingdie拼合锻模splitmold双并式模具spruelessmold无注道残料模具squeezingdie挤压模stretchformdie拉伸成形模sweepingmold平刮铸模swingdie振动模具threeplatesmold三片式模具trimmingdie切边模unitmold单元式模具universalmold通用模具unscrewingmold退扣式模具yoketypedie轭型模模具词汇英语翻译(模具常用成形方式) accuratediecasting精密压铸powderforming粉末成形calendaringmolding压延成形powdermetalforging粉末锻造coldchamberdiecasting冷式压铸precisionforging精密锻造coldforging冷锻pressforging冲锻compactingmolding粉末压出成形rockingdieforging摇动锻造compoundmolding复合成形rotaryforging回转锻造compressionmolding压缩成形rotationalmolding离心成形dipmold浸渍成形rubbermolding橡胶成形encapsulationmolding注入成形sandmoldcasting砂模铸造extrusionmolding挤出成形shellcasting壳模铸造foamforming泡沫成形sinterforging烧结锻造forgingroll轧锻sixsidesforging六面锻造gravitycasting重力铸造slushmolding凝塑成形hollow(blow)molding中空(吹出)成形squeezecasting高压铸造hotchamberdiecasting热室压铸swaging挤锻hotforging热锻transfermolding转送成形injectionmolding射出成形warmforging温锻investmentcasting精密铸造matcheddiemethod对模成形法laminatingmethod被覆淋膜成形lowpressurecasting低压铸造lostwaxcasting脱蜡铸造matchedmouldthermalforming对模热成形模模具词汇英语翻译(成形不良用语) aberration色差bite咬入blackinghole涂料孔(铸疵)blackingscab涂料疤blister起泡blooming起霜blowhole破孔blushing泛白bodywrinkle侧壁皱纹breaking-in冒口带肉bubble膜泡burnmark糊斑burr毛边camber翘曲cell气泡centerbuckle表面中部波皱check细裂痕checking龟裂chipping修整表面缺陷clamp-off铸件凹痕collapse塌陷colormottle色斑corrosion腐蚀crack裂痕crazing碎裂crazing龟裂deformation变形edge切边碎片edgecrack裂边fading退色fillerspeak填充料斑fissure裂纹flangewrinkle凸缘起皱flaw刮伤flowmark流痕galling毛边glazing光滑gloss光泽greasepits污斑grindingdefect磨痕haircrack发裂haze雾度incrustation水锈indentation压痕internalporosity内部气孔mismatch偏模mottle斑点necking缩颈nick割痕rangepeel橘皮状表面缺陷overflow溢流peeling剥离pit坑pittingcorrosion点状腐蚀platemark模板印痕pock麻点pockmark痘斑resinstreak树脂流纹resinwear树脂脱落riding凹陷sagging松垂saponification皂化scar疤痕scrap废料scrapjam废料阻塞scratch刮伤/划痕scuffing深冲表面划伤seam裂痕shockline模口挤痕shortshot充填不足shrinkagepool凹孔sinkmark凹痕skininclusion表皮摺叠straightening矫直streak条状痕surfacecheck表面裂痕surfaceroughening橘皮状表皮皱摺surging波动torsion扭曲warpage翘曲waviness波痕webbing熔塌weldmark焊痕whitening白化wrinkle皱纹模具词汇英语翻译(塑胶原料)acrylic压克力casein酪素celluloseacetate醋酸纤维素CAcelluloseacetatebutyrate醋酸丁酸纤维素CABcompositematerial复合材料cresolresin甲酚树脂CFdiallyphthalate苯二甲酸二烯丙酯dispersereinforcement分散性强化复合材料engineeringplastics工程塑胶epoxyresin环氧树脂EPethylcellulose乙基纤维素ethylenevinylacetatecopolymer乙烯-醋酸乙烯EVAethylene-vinlacetatecopolyme醋酸乙烯共聚物EVAfiberreinforcement纤维强化热固性/纤维强化复合材料highdensitypolyethylene高密度聚乙烯HDPEhighimpactpolystyrene高冲击聚苯乙烯HIPShighimpactpolystyrenerigidity高冲击性聚苯乙烯lowdensitypolyethylene低密度聚乙烯LDPEmelamineresin三聚氰胺酚醛树脂MFnitrocellulose硝酸纤维素phenolicresin酚醛树脂plastic塑胶polyacrylicacid聚丙烯酸PAPpolyamide耐龙PApolybutyleneterephthalate聚对苯二甲酸丁酯PBTpolycarbonate聚碳酸酯PCpolyethyleneglycol聚乙二醇PFGpolyethyleneoxide聚氧化乙烯PEOpolyethyleneterephthalate聚乙醇对苯PETPpolymetylmethacrylate聚甲基丙烯酸甲酯PMMApolyoxymethylene聚缩醛POMpolyphenyleneoxide聚硫化亚苯polyphenyleneoxide聚苯醚PPOpolypropylene聚丙烯PPpolystyrene聚苯乙烯PSpolytetrafluoroethylene聚四氟乙烯PTFEpolytetrafluoroethylene聚四氟乙烯polythene聚乙烯PEpolyurethane聚氨基甲酸酯PUpolyvinylacetate聚醋酸乙烯PVACpolyvinylalcohol聚乙烯醇PVApolyvinylbutyral聚乙烯醇缩丁醛PVBpolyvinylchloride聚氯乙烯PVCpolyvinylfuoride聚氟乙烯PVFpolyvinylidenechloride聚偏二氯乙烯PVDCprepolymer预聚物siliconeresin矽树脂thermoplastic热塑性thermosetting热固性thermosettingplastic塑胶unsaturatedpolyester不饱和聚酯树脂模具词汇英语翻译(射出成形)activator活化剂bagmoulding气胎施压成形bondingstrength黏合强度breathing排气caulkingcompound填隙料cell气孔coldslug半凝式射出colorant著色剂colormatching调色colormasterbatch色母料compound混合料copolymer共聚合体cull残料废品cure凝固化cryptometer不透明度仪daylight开隙drycycletime空料试车周期时间ductility延性elastomer弹性体extrudedbeadsealing压出粒涂层法feed供料filler充填剂filmblowing薄膜吹制法floatingplaten活动模板foamingagent发泡剂gloss光泽granule颗粒料gunk料斗hotmark热斑hotstamping烫印injectionnozzle射出喷嘴injectionplunger射出柱塞injectionram射出冲柱isomer同分异构物kneader混合机levelingagent匀涂剂lubricant润滑剂matcheddiemethod配合成形法mouldclampingforce锁模力mouldreleaseagent脱模剂nozzle喷嘴orientedfilm取向薄膜parison吹气成形坏料pellet粒料plasticizer可塑剂plunger压料柱塞porosity孔隙率postcure后固化premix预混料purging清除reciprocatingscrew往复螺杆resilience回弹性resininjection树脂射出法rheology流变学sheet塑胶片shot注射shotcycle射出循环slipagent光滑剂takeoutdevice取料装置tiebar拉杆toggletypemouldclampingsystem肘杆式锁模装置torpedospreader鱼雷形分流板transparency透明性voidcontent空洞率模具词汇英语翻译(表面处理) agehardening时效硬化ageing老化处理airhardening气体硬化airpatenting空气韧化annealing退火anodeeffect阳极效应anodizing阳极氧化处理atomloytreatment阿托木洛伊表面austempering奥氏体等温淬火austenite奥斯田体/奥氏体bainite贝氏体bandedstructure条纹状组织barrelplating滚镀barreltumbling滚筒打光blackening染黑法blueshortness青熟脆性bonderizing磷酸盐皮膜处理boxannealing箱型退火boxcarburizing封箱渗碳brightelectroplating辉面电镀brightheattreatment光辉热处理bypassheattreatment旁路热处理carbide炭化物carburizedcasedepth浸碳硬化深层carburizing渗碳cementite炭化铁chemicalplating化学电镀chemicalvapordeposition化学蒸镀coarsening结晶粒粗大化coating涂布被覆coldshortness低温脆性comemtite渗碳体controlledatmosphere大气热处理cornereffect锐角效应creepingdischarge蠕缓放电decarburization脱碳处理decarburizing脱碳退火depthofhardening硬化深层diffusion扩散diffusionannealing扩散退火electrolytichardening电解淬火embossing压花etching表面蚀刻ferrite肥粒铁firststageannealing第一段退火flamehardening火焰硬化flametreatment火焰处理fullannealing完全退火gaseouscyaniding气体氧化法globularcementite球状炭化铁grainsize结晶粒度granolitetreatment磷酸溶液热处理graphitizing石墨退火hardenability硬化性hardenabilitycurve硬化性曲线hardening硬化heattreatment热处理hotbathquenching热浴淬火hotdipping热浸镀inductionhardening高周波硬化ioncarbonitriding离子渗碳氮化ioncarburizing离子渗碳处理ionplating离子电镀isothermalannealing等温退火liquidhoning液体喷砂法lowtemperatureannealing低温退火malleablizing可锻化退火martempering麻回火处理martensite马氏体/硬化铁炭metallikon金属喷镀法metallizing真空涂膜nitriding氮化处理nitrocarburizing软氮化normalizing正常化oilquenching油淬化overageing过老化overheating过热pearlite针尖组织phosphating磷酸盐皮膜处理physicalvapordeposition物理蒸镀plasmanitriding离子氮化pre-annealing预备退火precipitation析出precipitationhardening析出硬化pressquenching加压硬化processannealing制程退火quenchageing淬火老化quenchhardening淬火quenchingcrack淬火裂痕quenchingdistortion淬火变形quenchingstress淬火应力reconditioning再调质recrystallization再结晶redshortness红热脆性residualstress残留应力retainedaustenite残留奥rustprevention防蚀saltbathquenching盐浴淬火sandblast喷砂处理seasoning时效处理secondstageannealing第二段退火seculardistortion经年变形segregation偏析selectivehardening部分淬火shotblast喷丸处理shotpeening珠击法singlestagenitriding等温渗氮sintering烧结处理soaking均热处理softening软化退火solutiontreatment固溶化热处理spheroidizing球状化退火stabilizingtreatment安定化处理straighteningannealing矫直退火strainageing应变老化stressrelievingannealing应力消除退火subzerotreatment生冷处理supercooling过冷surfacehardening表面硬化处理temperbrittleness回火脆性tempercolour回火颜色tempering回火temperingcrack回火裂痕texture咬花thermalrefining调质处理thermoechanicaltreatment加工热处理timequenching时间淬火transformation变态tufftrideprocess软氮化处理underannealing不完全退火vacuumcarbonitriding真空渗碳氮化vacuumcarburizing真空渗碳处理vacuumhardening真空淬火vacuumheattreatment真空热处理vacuumnitriding真空氮化waterquenching水淬火wetout浸润处理模具词汇英语翻译(模具常用刀具工作法) adjustablespanner活动扳手anglecutter角铣刀arbour心轴backing衬垫beltsander带式打磨机buffing抛光chamferingmachine倒角机chamferingtool去角刀具chisel扁錾chuck夹具compass两角规concavecutter凹面铣刀convexcutter凸形铣刀crossjoint十字接头cuttingedgeclearance刃口余隙角drillstand钻台edgefile刃用锉刀file锉刀flangejoint凸缘接头grinder砂轮机hammer铁锤handbrace手摇钻hatching剖面线hexagonheadedbolt六角头螺栓hexagonnut六角螺帽indexhead分度头jack千斤顶jig治具kit工具箱lapping研磨metalsaw金工锯noseangle刀角pinchers钳子pliers铗钳plug柱塞头polisher磨光器protabledriller手提钻孔机punch冲头sandpaper砂纸scraper刮刀screwdriver螺丝起子scribing划线secondoutfile中纹锉spanner扳手splinebroach方栓槽拉刀square直角尺squaresleeker方形镘刀squaretrowel直角度stripping剥离工具T-slotT形槽toolforlathe车刀toolpointangle刀刃角toolpost刀架tosecan划线盘trimming去毛边waffledieflattening压纹效平wiper脱模钳wrench螺旋扳手模具词汇英语翻译(冲模加工) barreling滚光加工belling压凸加工bending弯曲加工blanking下料加工bulging撑压加工burring冲缘加工camdiebending凸轮弯曲加工coining压印加工compressing压缩加工compressionbending押弯曲加工crowning凸面加工curlbending卷边弯曲加工curling卷曲加工cutting切削加工dinking切断蕊骨doubleshearing叠板裁断drawing引伸加工drawingwithironing抽引光滑加工embossing浮花压制加工extrusion挤制加工filing锉削加工fineblanking精密下料加工finishblanking光制下料加工finishing精整加工flanging凸缘加工folding折边弯曲加工folding摺叠加工forming成形加工impactextrusion冲击挤压加工indenting压痕加工ironing引缩加工knurling滚花lockseaming固定接合louvering百叶窗板加工marking刻印加工necking颈缩加工notching冲口加工parting分断加工piercing冲孔加工progressivebending连续弯曲加工progressiveblanking连续下料加工progressivedrawing连续引伸加工progressiveforming连续成形加工reaming铰孔加工restriking二次精冲加工riveting铆接加工rollbending滚筒弯曲加工rollfinishing滚压加工rolling压延加工roughing粗加工scraplessmachining无废料加工seaming折弯重叠加工shaving缺口修整加工shearing切断加工sizing精压加工/矫正加工slitting割缝加工spinning卷边?接stamping锻压加工swaging挤锻压加工trimming整缘加工upsetting锻粗加工wiring抽线加工模具词汇英语翻译(冲压机械及周边) backshaft支撑轴blankdetermination胚料展开bottomslidepress下传动式压力机boarddrophammer板落锤brake煞车buckle剥砂面camlachiecramp铸包chamottesand烧磨砂charginghopper加料漏斗clearance间隙closed-dieforging合模锻造clump夹紧clutch离合器clutchbrake离合器制动器clutchboss离合器轮壳clutchlining离合器覆盖coilcar带卷升降运输机coilcradle卷材进料装置coilreelstand钢材卷料架column圆柱connectionscrew连杆调节螺钉corecompound砂心黏结剂counterblowhammer对击锻锤cradle送料架crank曲柄轴crankless无曲柄式crosscrank横向曲轴cushion缓冲depression外缩凹孔dialfeed分度送料dieapproach模口角度dieassembly合模diecushion模具缓冲垫dieheight冲压闭合高度dielife模具寿命dieopening母模逃孔diespottingpress调整冲模用压力机doublecrankpress双曲柄轴冲床draghtangle逃料倾斜角edging边锻伸embeddedcore加装砂心feedlength送料长度feedlevel送料高度fillingcore埋入砂心fillingin填砂filmplay液面花纹fineblankingpress精密下料冲床forgingroll辊锻机finishingslag炼后熔渣flywheel飞轮flywheelbrake飞轮制动器footpress脚踏冲床formboard进模口板frame床身机架friction摩擦frictionbrake摩擦煞车gapshear凹口剪床gear齿轮gib滑块引导部gripper夹具gripperfeed夹持进料gripperfeeder夹紧传送装置hammer槌机handpress手动冲床handrackpinionpress手动齿轮齿条式冲床handscrewpress手动螺旋式冲床hopperfeed料斗送料idlestage空站inching微调尺寸isothermalforging恒温锻造keyclutch键槽离合器knockout脱模装置knucklemechanic转向机构land模具直线刀面部loader供料器unloader卸料机loopcontroller闭回路控制器lowerdie下模microinchingdevice微寸动装置microinchingequipment微动装置movingbolster活动工作台notchingpress冲缺口压力机opening排料逃孔overloadprotectiondevice防超载装置pinchroll导正滚轮pinion小齿轮pitch节距pressfit压入progressive连续送料pusherfeed推杆式送料pusherfeeder料片押片装置quickdiechangesystem快速换模系统regrinding再次研磨releasing松释动作reversedblanking反转下料robot机器人rollformingmachine辊轧成形rollformingmachine辊轧成形机rollrelease脱辊rollerfeed辊式送料rollerleveler辊式矫直机rotarybender卷弯成形机safetyguard安全保护装置scrapcutter废料切刀scrappress废料冲床seamlessforging无缝锻造shave崩砂shearangle剪角sheetloader薄板装料机shot单行程工作shrinkagefit收缩配合shutheight闭合高度sievemesh筛孔sinteringofsand铸砂烧贴slidebalancer滑动平衡器slughole逃料孔spinformingmachine旋压成形机spotting合模stackfeeder堆叠拨送料机stickness黏模性straightsideframe冲床侧板stretcherleveler拉伸矫直机stripfeeder料材送料装置strippingpressure弹出压力stroke冲程takeoutdevice取料装置togglepress肘杆式压力机transferfeed连续自动送料装置turrentpunchpress转塔冲床twospeedclutch双速离合器uncoiler闭卷送料机unloader卸载机vibrationfeeder振动送料机wiringpress嵌线卷边机模具词汇英语翻译(线切割放电加工关连用语) abnormalglow不规则辉光放电arcdischarge电弧放电belt皮带centreless无心chromebronze铭铜clearanceangle后角cornersheardrop直角压陷deflection桡曲度dischargeenergy放电能量dressing修整dwell保压flange凸缘gap间隙graphite石墨graphitecontractionallowance电极缩小余量graphiteholder电极夹座haircrack发裂horn电极臂jump跳刀magneticbase磁性座mastergraphite标准电极pipegraphite管状电极pulse脉冲ribworking肋部加工rollerelectrode滚轮式电极rotarysurface旋转面shank柄部sharpedge锐角部toughbronze韧铜traverse摇臂tungstenbronze钨青铜waviness波形起伏workingallowance加工余量workingdischard加工废料模具相关词汇英语翻译(锻铸造关连用语) accretion炉瘤acidconverter酸性转炉acidliningcupola酸性熔铁炉acidopen-hearthfurnace酸性平炉aerator松砂机airsetmold常温自硬铸模airlessblastingcleaning离心喷光allcoremolding集合式铸模allrounddieholder通用模座assemblymark铸造合模记号backpouring补浇注backingsand背砂basebullion粗金属锭basepermeability原砂透气度belling压凸billet坏料bleed漏铸blocker预锻模膛blocking粗胚锻件blowhole铸件气孔boarddrophammer板落锤bottompourmold底浇bottompouring底注boxlessmold脱箱砂模break-offcore缩颈砂心brickmolding砌箱造模法buckle剥砂面camber错箱camlachiecramp铸包castblade铸造叶片castingflange铸造凸缘castingonflat水平铸造chamottesand烧磨砂charginghopper加料漏斗cleaningofcasting铸件清理closed-dieforging合模锻造corecompound砂心黏结剂coretemplate砂心模板corevent砂蕊排气孔cornergate压边浇口counterblowhammer对击锻造counterlock止口镶嵌方式depression外缩凹孔dieapproach模口角度drawout锻造拔长drawplate起模板drawspike起模长针dummying预锻embeddedcore加装砂心erosion冲砂fettling铸件清理fillingcore埋入砂心fillingin填砂filmplay液面花纹finishingslag炼后熔渣flashgutter锻模飞边槽flaskmolding砂箱造模forgingroll辊锻机formboard进模口板gutter锻模飞边槽hammerman锻工headingmachine顶镦机impacter卧式锻造机inblockcast整体铸造ingot铸锭ingotblank铸坯inlaycasting镶铸法investmentcasting失模铸造isothermalforging恒温锻造loosepiece木模活块moldingpit铸模地坑pouringprocess浇注法recasting重铸rollforging轧锻rolledsurface轧制表面roughsand粗砂roughingforge粗锻sandcrushing塌箱seamlessforging无缝锻造separate分离shave崩砂shrinkagefit收缩配合shutheight闭合高度sievemesh筛孔sinteringofsand铸砂烧贴slag熔渣slaginclusion夹渣stickness黏模性striplayout带状胚料排样法tapcasting顶注topgate顶注浇口unworkedcasting不加工铸件upender翻转装置upending顶锻uphillcasting底铸whitecastiron白口铸件模具词汇相关英语翻译(砂轮用语) abrasive砂轮Al2O3氧化铝borazon氧化硼立方晶buffingwheel抛光布轮diamond钻石dresser砂轮整修机dressing修整endlessgrindingbelt循环式研磨带finishingallowance加工余量grain磨粒grindingdisc研磨盘jampup孔眼堵塞mesh网筛目resinoidgrindingwheel半树脂型砂轮slitting切缝量vitrified陶瓷的模具加工方法词汇的英语翻译barrel滚筒(加工)bending波纹加工broaching拉刀切削centering定中心cutting切削cylindricallathecutting外圆车削electricdischargemachine放电加工electrolyticgrinding电解研磨embossing压花加工facing面车削filing锉刀修润handfinishing手工修润hemming卷边加工hobbing滚齿加工joggling摇动加工lapping抛光/研磨修润laserbeammachining雷射加工lathecutting车床车削planning刨削加工polishing抛亮光reaming铰孔修润roughmachining粗切削rounding圆形加工sawing锯削scaling清除钢碇缺陷shaping成形加工skiving表面研磨slotting切缝切削taperturning锥度车削threadcutting螺纹切削ultrasonicmachining超音波加工upcutmilling逆铣加工特别声明：1：资料来源于互联网，版权归属原作者2：资料内容属于网络意见，与本账号立场无关3：如有侵权，请告知，立即删除。
模具工业中英文翻译
模具工业中英文翻译模具常用术语中英文对照局部视图 Partial View冷料# Cold Slag线切割 Wire E.D.M轮廊 Contour螺纹孔 Tapping Hole连接件 Fittings斜针 Angle Pin接合 Engage替换镶件Interchangeable Mold Inserts 指定吨位的注塑机 Specific Press水嘴接头 Water Fittings螺纹 Eyebolt Thread回针 Stop Pin二级顶出针Sub-Leaderd Pin镶件 Mold Insert 加硬 Harden唧嘴 Sprue设计筒图 Design Preliminary名称块表 Title Block版本标识 Revision Level材料清单 Stock List制模 Build Mold手动滑块 Hand Slide漏水测试 Leak Test流道排气 Runner Vents抛光 Draw Polish侧抽芯 Side Action加强筋 Reinforcing三角撑 Gusset柱子 Bossed出模斜度 Draft外廊 Contour落单会议 Kick-Off Meeting装卸孔 Handling Hole运输安全带 Moldstrap码模槽 Clamp Slot撑头 Support Pillar螺牙1/2-13 Eye Bolt 1/2-13Tap 导柱位 Leader Pin Location耐落胶 Teflon Paste偏移量 Offset水塞 Water Line Plug撬模脚 Ppy Slot重新加工 Reworked配件 Components补偿 Compensation平面度 Parallel倒角 Chamfer模胚 Mold Base热嘴 Hotnozzle火花机 Edm熔接线 Weildline压机 Press晒纹 Texturing梯形 Trapezoid凸缘、法兰 Flange方铁 Spacer Block顶针板 Ejector Plate顶针底板 Ejector Retainer Plate垫板 Retainer Plate后模镶针 Core Pin拉圾钉 Stop Pin有托顶针 Shoulder Ejector Pin顶针板导套 Guided Ejection Bushing针板导柱 Guided Ejection Leader Pin唧嘴 Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing定位圈（法兰） Locating Ring管钉（定位销） Dowel Pin管状管钉 Tubular Dowel吊环 Safety Hoist Ring日期印 Dating Insert环保印 Recycling Insert气顶 Air Poppet Valve截水口镶件 Runner Shut-Off Insert早回 Early Ejector Return加速项 Accelerated Ejector客户 Client 产品名 Part Name产品编号 Part No 缩水 Shrinkage版本 Rev 模胚 Mold Base下模镶件 Core Block上模镶件 Cavity Block小镶件 Sub-Insert下模小镶件 Core Sub-Insert上模小镶件 Cavity Sub-Insert行位 Slide行位镶件 Slide Insert压条 Gib压紧块（铲机） Jaw硬片（摩擦片） Wear Plate水口铁 Runner Bar上模水口铁 Upper Runner Bar下模水口铁 Lower Runner Bar弹簧 Spring水口勾针 Sprue Puller Pin顶针 Ejector Pin撑头 Support Pillar直身锁 Side Lock斜度锁 Interlock锁模板 Safety Bar‘O’令（密封圈） O'Ring喉塞 Plug隔水片 Baffle波子螺丝（行位定位螺丝） Ball-Catch 斜顶 Lifter控制开关 Switch回针 Return Pin斜导柱 Angle Pin推板 Stripper PlateA’板 A'PlateB’板 B'Plate方铁（垫铁）Spacer Block顶针板 Ejector Plate顶针底板 Ejector Retainer Plate垫板 Retainer Plate垃圾钉 Stop Pin有托顶针 Shoulder Ejector Pin顶针板导套 Guided Ejection Bushing针板导柱 Guided Ejection Leader Pin唧嘴 Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing定位圈（法兰） Locating Ring管钉（定位销） Dowel Pin管状管钉 Tubular Dowel吊环 Safety Hoist Ring日期印 Dating Insert环保印 Recycling Insert气顶 Air Poppet Valve截水口镶件 Runner Shut-Off Insert早回 Early Ejector Return加速顶 Accelerated Ejector扁顶 Blade 出模斜波 Draft手动滑块模具 Hand Slide-In Type Mold回针板 Backup合模 Shutoff空隙槽 Clearance Slot导柱及导套 Leader Pin Bushing水口拉钩 Spuer Puller模框镶件Pocket Insert成型热固性塑胶模具Thermoset Mold 三板模 3-Plat Mold分型面 Parting Line司筒 Ejector Sleeve垫圈 Washer熔接线（夹水纹） Weldline吸针 Sucker Pin回针板 Retainer Plate顶出板 Knock -Out Plate电动安全开关Electrical-Safety Switch 脱开 Cut Of Position预先决定 Preload缓冲器 Bumper衬垫 Cushion公差 Tolerance突然性动作 Slam销针 Dowel钩槽 Gib精磨 Finished通框 Through Window粘后模 Sticking Core粘水口 Sticking Sprue夹水纹 Weld Line变形 Warpage走水不平均 Filling Uneven走不齐 Short Shot挂成品 Part Hanging漏水 Water Leakage刮花（擦伤） Galling漏电 Ele Leakage困气 Air Trapping温度 Temperature注塑模 Injection Mold入水 Gate试板 Sampling压力 Pressure倒圆 Fillet顶棍 Ejector顶白 Stress Mark粘前模 Sticking Cav名称块表 Title Block版本标识 Revision Level材料清单 Stock List斜导柱（斜边） Angle PinA板 A'plateB板 B'plate倒扣 Under-Cut披峰 Flash缩水 Sink Mark氮化 Nitride不规则四边形Trapezoid缩水 Shrinkage连续的 Consecutive雕刻 Engrave出模角 Draft分模面 Parting Surface擦位 Shut-Off(S/0)导套 Bushing回针 Return Pin加硬 Harden唧嘴 Sprue设计筒图 Design Preliminary 丝印 Silkprint不干胶 Adhesive Sticker导向针 Guide Din公差 Tolerance线切割 Wire-Cut电火花 Edm抛光 Polishing蚀纹 Texture探热针 Thermocouple三打螺丝毫（限螺丝） Stripper Bolt 盖板 Cover Plate齿轮 Gear油唧 Hydraulic Cylinder司筒 Ejector Sleeve导柱 Leader Pin冷料# Cold Slag线切割 Wire E.D.M.轮廓 Contour螺纹孔 Tapping Hole连接件 Fittings斜针 Angle Pin接合 Engage替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press水嘴接头 Water Fittings螺纹 Eyebolt Thread回针 Stop Pin二级顶出针 Sub-Leader Pin镶件 Mold Insert锁定位 Lock楔子(铲鸡) Wedge高产量模量 High V olume Running Mold 剖面图 Cross Section 模具结构 Mold Construction模芯 Parting Core局部视图 Partial View热流道 Manifold热嘴 Hot Nozzle型腔数 Cav No模号 Mold No胶料 Material尺寸 Dimension重要尺寸 Critical Dimension雕刻 EngraveAssembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试V oltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource department 人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |'plein?|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor 副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dei?n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzer蜂鸣器defective product label不良标签identifying sheet list标示单location地点present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/ 承办PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明yearend physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/ good parts 良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack 上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机。
翻译常用模具专业术语
模具专业英语一：入水：gate进入位：gate location 水口形式：gate type 大水口：edge gate细水口：pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter二、流道：runner热流道：hot runner,hot manifold 唧嘴直流：direct sprue gate流道电脑分析：mold flow analysis 热嘴：hot sprue发热管:cartridge heater插头： connector plug密封/封料：seal—、运水：water line塑胶管:plastic tube四、模具零件：mold components热嘴)令流道:hot sprue/cold runner圆形流道:round(full∕half runner流道平衡:runner balance热流道板：hot manifold探针:thermocouples插座：connector socket快速接头：jiffy quick connector plug/socker二板模:2-plate mold边司/导套:bushing/guide bushing 中托边L ： guide pin托板: support plate管钉：dowel pin内模管位:core/cavity inter-lock司筒：ejector sleeve推板：stripper plate缩呵：movable core, return core puller扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter模胚（架）：mold base 上内模：cavity insert下内模：core insert 行位（滑块）：slide镶件：insert耐磨板/油板：wedge wear plate撑头：support pillar挡板：stop plate锁扣：latch推杆:push bar顶板：eracuretun分流锥：spure sperader垃圾钉：Stop pin弹弓柱:spring rod中托司：ejector guide bush 镶针：pin 波子弹弓:ball catch压座/斜鸡：wedge压条：plate唧嘴:sprue bushing定位圈:locating ring扣鸡:parting lock set栓打螺丝：S.H.S.B活动臂:lever arm水口司:bush隔片:buffle弹弓:die spring中托边:ejector guide pin销子：dowel pin喉塞:line lpug 喉管：tube三板模:3-plate mold边钉/导边:leader pin/guide pin 中托司：shoulder guide bushing 顶针板：ejector retainer plate 螺丝：screw开模槽:P∣y bar scot顶针：ejector pin司筒针∙ejector pin模具成形不良用语英汉对比aberration 色差atomization 彳匕blacking hole涂料孔（铸疵）blister 起泡blooming 起霜body wrinkle侧壁皱纹bubble 膜泡burn mark 糊斑cell气泡center buckle表面中部波皱chipping修整表面缺陷collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation变形edge切边碎片edge crack 裂边fading 退色filler speak填充料斑fissure裂纹flange wrinkle凸缘起皱flaw刮伤flow mark 流痕galling 毛边glazing光滑gloss光泽grease pits ）亏斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick割痕orange peel橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀bank mark 料纹bite咬入blacking scab 涂料疤low hole 破孔blushing 泛白breaking-in 冒口带肉burr毛边camber翘曲check细裂痕checking龟裂clamp-off铸件凹痕plate mark模板印痕pock麻点pock mark 痘斑resin streak 树脂流纹resin wear树脂脱落riding凹陷sagging 松垂saponification 皂化scar疤痕scrap废料scrap jam废料堵塞scratch刮伤/划痕scuffing深冲表面划伤seam裂痕shock line模口挤痕short shot充填不足shrinkage pool 凹孑I sink mark 凹痕skin inclusion 表皮折叠straightening 矫直streak条状痕surface check表面裂痕surface roughening橘皮状表皮皱折surging波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹各式模具分类用语英汉对比landed plunger mold有肩柱塞式模具burnishing die 挤光模landed positive mold有肩全压式模具button die镶人式圆形凹模loading shoe mold料套式模具center-gated mold中心浇口式模具loose detail mold活零件模具chill mold冷硬用铸模loose mold活动式模具clod hobbing冷挤压制模lowering die百叶窗冲切模composite dies复合模具manifold die分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold复式浇口模具expander die扩径模offswt bending die双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold反套制品模具plaster mold 石膏模blank through dies漏件式落料模porous mold通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die扇尾形模具pressure die压紧模fishtail die鱼尾形模具profile die轮廓模flash mold溢料式模具progressive die挨次模gypsum mold 石膏铸模protable mold 手提式模具 hot-runner mold 热流道模具 prototype mold 雏形试验模具 ingot mold 钢锭模 punching die 落料模lancing die 切口模 raising(embossing)压花起伏成形 re-entrant mold 倒角式模具 sectional die 拼合模 runless injection mold 无流道冷料模具 sectional die 对合模具 segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具 solid forging die 整体锻模 split forging die 拼合锻模 split mold 双并式模具sprueless mold 无注道残料模具 squeezing die 挤压模 stretch form die 拉伸成形模 sweeping mold 平刮铸模swing die 振动模具 three plates mold 三片式模具 trimming die 切边模 unit mold 单元式模具universal mold 通用模具 unscrewing mold 退扣式模具 yoke type die 规型模各种模具常用成形方式英汉对比accurate die casting 精密压铸 powder forming 粉末成形 calendaring molding 压延成形 powder metal forging 粉末锻造 cold chamber die casting 冷式压铸 precision forging 精密锻造 cold forging 冷锻 press forging 冲锻 compacting molding 粉末压出成形 rocking die forging 摇动锻造compound molding 复合成形 rotary forging 回转锻造 compression molding 压缩成形 rotational molding 离心成形dip mold 浸'溃成形rubber molding 橡胶成形 encapsulation molding 注入成形 sand mold casting 砂模铸造extrusion molding 挤出成形 shell casting 壳模铸造foam forming 泡成形 sinter forging 烧结锻造 forging roll 轧锻 six sides forging 六面锻造gravity casting 重力铸造 slush molding 凝塑成形 hollow(blow) molding 中空(吹出)成形 squeeze casting 高压铸造hot chamber die casting 热室压铸 swaging 挤锻 hot forging 热锻transfer molding 转送成形injection molding 射出成形 warm forging 温锻 investment casting 精密铸造 matched die method 对模成形法 laminating method 被覆淋膜成形 low pressure casting 彳氐压铸造 lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形机械类常用英语：冲压模具•零件类special shape punch 异形冲子 bending block 折刀 roller 滚轴 baffle plate 挡块 located block 定位块supporting block for location 定位支承块机械类常用英语：冲压模具•模板类trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子punch 冲头insert 入块（嵌入件） deburring punch 压毛边冲子 groove punch 压线冲子 stamped punch 字模冲子 round punch 圆冲子air cushion plate 气垫板 air-cushion eject-rod 气垫顶杆ribbon punch 压筋冲子reel-stretch punch卷圆压平冲子guide plate 定位板sliding block 滑块sliding dowel block 滑块固定块active plate 活动板lower sliding plate 下滑块板upper holder block 上压块top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder 上夹板stripper pad脱料背板up stripper上脱料板male die公模（凸模）feature die 公母模female die母模（凹模）upper plate 上模板upper mid plate 上中间板spring box弹簧箱spring-box eject-rod 弹簧箱顶杆spring-box eject-plate 弹簧箱顶板bushing bolck 衬套cover plate 盖板guide pad导料块lower plate 下模板die pad下垫板die holder下夹板die set下模座bottom block 下垫脚bottom plate下托板（底板）stripping plate内外打（脱料板）outer stripper 外脱料板inner stripper 内脱料板lower stripper 下脱料板冲压模具.冲压名称类英汉对比reel stretch卷圆压平groove压线blanking 下料stamp letter 冲字（料号）shearing 剪断tick-mark nearside 正面压印tick-mark farside 反面压印extension dwg 绽开图procedure dwg 工程图die structure dwg模具结构图material 材质material thickness 料片厚度factor系数upward向上downward 向下press specification 冲床规格die height range 适用模高die height闭模高度plain die简易模pierce die冲孔模forming die 成型模progressive die 连续模gang dies复合模shearing die 剪边模riveting die 钏合模pierce冲孔forming成型（抽凸，冲凸）draw hole 抽孔bending 折弯trim切边emboss凸点dome凸圆semi-shearing 半剪stamp mark冲记号deburr or coin 压毛边punch riveting 冲压枷合burr毛边total wt.总重量 punch wt.上模重量模具工程常用词汇英汉对比high-speed transmission 高速传递 heat dissipation 热传 rack 上料 degrease 脱脂 rinse 水洗 alkaline etch 龄咬 desmut 剥黑膜 D.l. rinse 纯水次 Chromate 铭酸处理 Anodize 阳性处理 seal 封孔 revision 版次 part number/P/N 料号 good products 良品 scraped products 报放心品 defective products 不良品 finished products 成品 disposed products 处壬里品 barcode 条码 flow chart 流程表单 assembly 组装 stamping 冲压 molding 成型spare parts=buffer 备品 coordinate 座标 dismantle the die 折模 auxiliary faction 帮助功能 poly-line 多义线 heater band 加热片 thermocouple 热电偶 sand blasting 喷沙 grit 砂砾derusting machine 除锈机 degate 打浇口 dryer 烘干机 induction 感应 induction light 感应光gap 间隙 weight 重量ram 连杆 edge finder 巡边器 concave 凸 convex Γtj l short 射料不足 nick 缺口 speck 瑕 shine 亮班 splay 银纹 gas mark 焦痕 delamination 起鳞 cold slug 冷块 blush 导色 gouge 沟槽;凿槽 satin texture 段面咬花 witness line 证示线 patent 专利 grit 沙砾granule=peuet=grain 细粒 grit maker 抽粒机 cushion 缓冲 magnalium 镁铝合金 magnesium 镁金 metal plate 板金 lathe 车 mill 铿 plane 包∣J grind 磨 drill 铝 boring 锋 blinster 气泡 fillet 镶;嵌边through-hole form 通孔形式 voller pin formality 滚针形式 cam driver 锄楔 shank 摸柄response=reaction=interaction 感应velocity 速度production tempo生产进度现状torque扭矩spline=the multiple keys 花键quenching 淬火tempering 回火annealing 退火carbonization 碳化alloy合金tungsten high speed steel 鸨高速的moly high speed steel 铝高速的模具工程常用词汇英汉对比stock age analysis sheet库存货龄分析表on-hand inventory 现有库存available material 良品可使用obsolete material 良品已呆滞to be inspected or reworked 待验或重工total合计part number/ P/N 料号type形态item/group/class 类另，quality 品质prepared by 制表notes 说明cause description 缘由说明终盘点差异分析表physical inventory 盘点数量physical count quantity 帐面数量difference quantity 差异量cause analysis 缘由分析raw materials 原料materials 物料finished product 成品semi-finished product 半成品packing materials 包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts 不良品disposed goods 处理品warehouse/hub 仓库on way location 在途仓oversea location 海外仓spare parts physical inventory list 备品盘点清单spare molds location 模具备品仓organic solvent 有机溶剂bracket小磁导liaison联络单volatile挥发性resistance 电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破裂机skid/pallet 栈板to× machine 自旬∣1 机wire EDM 线割EDM放电机coil stock 卷料sheet stock 片料tolerance 工差score=groove 压线cam block 滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head 挂钩槽slug hole废料孔feature die 公母模expansion dwg 绽开图radius半径shim(wedge)楔子torch-flame cut 火焰切割set screw止付螺丝form block 折刀Stop pin定位销round pierce punch=die button 圆冲子shape punch=dιe insert 异形子stock locater block 定位块under cut=scrap chopper 清角active plate 活动板baffle plate 挡块cover plate 盖板male die 公模female die 母模groove punch压线冲子air-cushion eject-rod 气垫顶杆spring-box eject-plate 弹簧箱顶板bushing block 衬套insert入块club car高尔夫球车capability 力量parameter 参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping 脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization 去磁;消磁模具工程常用词汇英汉对比padding block 垫块stepping bar 垫条upper die base 上模座lower die base 卜模座upper supporting blank 上承板upper padding plate blank 上垫板spare dies模具备品spring弹簧bolt螺栓document folder 文件夹file folder 资料夹to put file in order 整理资料spare tools location 手工备品仓first count 初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment 设施waste materials 废料work in progress product 在制品casing = containerazation 装箱quantity of physical invetory second count 复盘点数量quantity of customs countdie模具figure file, chart file 图档cutting die, blanking die 冲裁模progressive die, follow (-on)die连续模compound die 复合模punched hole 冲孔panel board 镶块to cutedges=side cut=side scrap 切边to bending 折弯to pull z to stretch 拉伸Line streching, line pulling 线拉伸engraving, to engrave 亥(JEfl upsiding down edges 翻边to stake 钏合designing, to design 设计design modification 设计变化die block 模块folded block 折弯块sliding block 滑块location pin 定位销lifting pin 顶料销die plate, front board 模板会计师盘,点数量the first page 第一联filed by accounting department for reference 会计部存查end-user/using unit(department)使用单位summary of year-end physical inventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory list will be sent to accounting department together (Those of NHK will besent to financial department) physical inventory card年终盘点卡与清册使用一状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering mold testing 工程试模材米斗not included in physical inventory 不歹∣j入盘点sample样品incoming material to be inspected 进货待验description 品名steel/rolled steel 钢材物料统计明细表approved by / checked by / prepared by 核准/审核/办PCE assembly production schedule sheetPCE组装厂生产排配表model机铺work order 工令revision 版次remark 备注production control confirmation 生产确认checked by 初审approved by 核准department 部门模具钢材alloy tool steel合金工具钢aluminium alloy 铝合金钢bearing alloy轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel碳素工具钢clad sheet被覆板clod work die steel 冷锻模用钢emery金钢砂ferrostatic pressure 钢铁水静压力forging die steel锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel超硬合金钢high speed tool steel高速度工具钢hot work die steel热锻模用钢low alloy tool steel 特别工具钢low manganese casting steel 彳氐镒铸钢marging steel马式体高强度热处理钢martri× alloy马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron市售钢材molybdenum high speed steel 铝系高速钢molybdenum steel 铝钢nickel chromium steel 银铭钢prehardened steel 顶硬钢silicon steel sheet 硅钢板stainless steel 不锈与冈tin plated steel sheet 镀锡铁板meeting minutes 会议纪l录meeting type 会另!jdistribution department 分发单位location 地点chairman 主席present members 出席人员subject 主题conclusion 结论decision items 决议事项responsible department 负责单位pre-fixed finishing date 预定完成日模具钢材及零件英语tough pitch copper 韧铜vinyl tapped steel sheet 塑料覆面钢板零件英语一塑件&模具相关英文leather cloak 仿皮革 shiver 饰纹 flow mark 流痕 welding mark 溶合痕post screw insert 螺纹套筒埋值 self tapping screw 自攻螺丝 striper plate 脱料板 piston 活塞 cylinder 汽缸套 chip 细碎物handle mold 手持式模具移转成型用模具encapsulation molding 低压封装成型 射出成型用模具two plate 两极式（模具）well type 蓄料井insulated runner 绝缘浇道方式 hot runner 热浇道 runner plat 浇道模块 valve gate 阀门浇口 band heater 环带状的电热器 spindle 阀针 spear head 刨尖头 slag well 冷料井 cold slag 冷料渣 airvent 排气道 h=0.02~0.05mm w=3.2mm L=3~5mm welding line 熔合痕 eject pin 顶出针 knock pin 顶出销 return pin 回位销反顶针 sleave 套筒stripper plate 脱料板 insert core 放置人子runner stripper plate 浇道脱料板 guide pin 导销eject rod （bar ）（成型机）顶业捧troostite 吐粒散铁 tungsten steel 鸨钢punch 冲头insert 入块（嵌入件） deburring punch 压毛边冲子 groove punch 压线冲子 stamped punch 字模冲子 round punch 圆冲子special shape punch 异形冲子 bending block 折刀 roller 滚轴 baffle plate 挡块 located block 定位块supporting block for location 定位支承块 air cushion plate 气垫板 air-cushion eject-rod 气垫顶杆 trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子 ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子 guide plate 定位板 sliding block 滑块sliding dowel block 滑块固定块 active plate 活动板 lower sliding plate 卜滑块板 upper holder block 上压块 upper mid plate 上中间板 spring box 弹簧箱spring-box eject-rod 弹簧箱顶杆 spring-box eject-plate 弹簧箱顶板 bushing bolck 衬套 cover plate 盖板 guide pad 导料块compre sion molding 压缩成型 flash mold 溢流式模具 P ∣sitive mold 挤压式模具 split mold 分割式模具 cavity 型控母模 core 模心公模 taper 锥拔subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation 定向sprue gate射料浇口，直浇口nozzle射嘴slag well冷料•井side gate 侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate 闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=l∕2rl∕5tT=2.5~3.5mmdiaphragm gate 隔膜浇口ring gate环形浇口subarine gate 潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less 无浇道（sprue less）无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣sprue lock pin料头钩销（拉料杆）压铸die-cast注塑injection铸件casting/cast/founding起泡/气泡bubble/blister/airbubble缺料short-shots/undershot浇不足/*铸under-founding多料superfluities/superfluous material （alloy）顶针痕ejector（pins） mark彳白纹flow mark/flow line冷纹cold mark/cold streak油纹oil streak走水纹splash mark银纹silver streaks霜纹splay mark夹水纹silver streaks/flow line/weld line扣模/粘模spruesticking砂眼/气眼air hole（塑胶件）弯曲/变形warping/warpage变形deformation扭曲twist翅曲warp/warped材料错误usingwrong plastic material凸痕convex mark凹位/凹陷sink mark/dent mark 模具徐§披锋flashingftt损pare-mark/cutmark批凹pare off柱纹trim-mark/file-mark铿损excessivetrim mark黑点/黑纹black spots/black streak发白white mark烧焦burnmarks刮花/刮痕scratch mark擦痕/擦伤rub-mark/brush-burn裂缝cracking裂纹crakingline51tS stress mark起皮chip错位（合模线）Parting line misalignment孔位尺寸转变dimensionvarious哑色dull color表面变光滑（喷油面）glossy finishing表面sruface/outside镶件insert/insert word缩水/收缩sinkmark/shrinkage/shrink mark偏差colordeviation色粉colourment 颜色colour/color斜针 Angle Pin 接合 Engage替换镶件 Interchangeable Mold Inserts 指定吨位的注塑机Specific Press 水嘴接头 Water Fittings 螺纹 Eyebolt Thread 回针 Stop Pin二级顶出针 Sub-Leaderd Pin 镶件 Mold Insert 加硬 Harden 唧嘴 Sprue设计筒图 Design Preliminary 名称块表 Title Block 版本标识 Revision Level 材料清单 Stock List 制模 Build Mold 手动滑块 Hand Slide 漏水测试Leak Test 流道排气 Runner Vents 抛光 Draw Polish 侧抽芯 Side Action 加强筋 Reinforcing 三角撑Gusset 柱子 Bossed 出模斜度Draft 外廊 Contour落单会议 Kick-Off Meeting 装卸孔 Handling Hole 运输平安带Moldstrap 码模槽Clamp Slot 撑头 Support Pillar螺牙 1/2-13 Eye Bolt l∕2-13Tap 导柱位 Leader Pin Location 耐落胶 Teflon Paste 偏移量Offset 水塞 Water Line Plug 撬模脚Ppy Slot 重新加工 Reworked 配件 Components 补偿 Compensation 平面度Parallel 倒角 Chamfer 模胚 Mold Base零件污糟 dirty mark on part I 页白 stressmark/ejector mark 屈曲bent夹模线移位 part line misalignment 胶件料厚不均 uneven wall thickness 水口料 degradedmaterial 凹印 sink mark 擦花 abrasionmark ，昆色 contamination mark 热点不良 poor heat sticking 模具方面： 定位圈 locating ring 唧嘴spruebush （浇口套） A 板Aplate （定模板） B 板Bplate （动模板） 方铁 spacer block （垫铁）底板bottom clamp p ∣ate （动模底板） 面板top clamp p ∣ate （定模底板） 顶针ejector pin （顶杆） 直边钉guide pin （导柱） 托司 shoulder guide bush （^⅛） 直司 straight guide bush （导柱） 回针returnpin （回程杆） 细水口边钉support pin （副导柱） 蓝弹簧blue spring （回程弹簧） 水口推板 runner stripper plate （卸流道板）中边钉ejector guide pin （顶板导柱） 顶针板ejector retainer p ∣ate （顶杆固定板）顶针底板ejectorplate （顶杆垫板） 撑头support pollar （支撑柱） 垃圾钉stop pin （限位钉） 呵core （后模肉内镶件）后模肉back mold body （后模镶件） 前模肉cavity （前模镶件） 扣鸡P-lock 模芯 Parting Core 局部视图 Partial View 冷料# Cold Slag 线切割 轮廊 Contour热嘴Hotnozzle火花机Edm熔接线Weildline压机Press哂纹Texturing梯形Trapezoid凸缘、法兰Flange方铁Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate后模镶针Core Pin拉圾钉Stop Pin有托顶针Shoulder Ejector Pin顶针板导套Guided Ejection Bushing针板导柱Guided Ejection Leader Pin唧嘴Sprue Bushing三板模延长式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing 定位圈（法兰）Locating Ring管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut-Off Insert早回Early Ejector Return加速项Accelerated Ejector客户Client产品名Part Name产品编号Part No缩水Shrinkage版本Rev模胚Mold Base下模镶件Core Block上模镶件Cavity Block小镶件Sub-Insert下模小镶件Core Sub-Insert上模小镶件Cavity Sub-Insert行位Slide行位镶件Slide Insert压条Gib压紧块（铲机）Jaw 硬片（摩擦片）Wear Plate水口铁Runner Bar上模水口铁Upper Runner Bar下模水□铁Lower Runner Bar弹簧Spring水口勾针Sprue Puller Pin顶针Ejector Pin撑头Support Pillar直身锁Side Lock斜度锁Interlock锁模板Safety Bar'0'令（密封圈）O'Ring喉塞Plug隔水片Baffle波子螺丝（行位定位螺丝）Ball-Catch斜顶Lifter掌握开关Switch回针Return Pin斜导柱Angle Pin推板Stripper PlateA'板A'PlateB'板B,Plate方铁（垫铁）Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate垃圾钉Stop Pin有托顶针Shoulder Ejector Pin顶针板导套Guided Ejection Bushing针板导柱Guided Ejection Leader Pin唧嘴Sprue Bushing三板模延长式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing 定位圈（法兰）Locating Ring管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut-Off Insert早回Early Ejector Return加速顶Accelerated Ejector扁顶Blade出模斜波Draft手动滑块模具Hand Slide-In Type Mold 回针板Backup合模Shutoff空隙槽Clearance Slot导柱及导套Leader Pin Bushing水口拉钩Spuer Puller模框镶件Pocket Insert成型热固性塑胶模具Thermoset Mold 三板模3-Plat Mold分型面Parting Une司筒Ejector Sleeve垫圈Washer熔接线（夹水纹）Weldline吸针Sucker Pin回针板Retainer Plate顶出板Knock -Out Plate电动平安开关Electrical-Safety Switch 脱开Cut Of Position预先打算Preload缓冲器Bumper衬■垫Cushion公差Tolerance突然性动作Slam销针Dowel钩槽Gib精磨Finished通框Through Window粘后模Sticking Core粘水口Sticking Sprue夹水纹Weld Line变形Warpage走水不平均Filling Uneven走不齐Short Shot挂成品Part Hanging漏水Water Leakage刮花（擦伤）Galling漏电Ele Leakage困气Air Trapping 温度Temperature注塑模Injection Mold入水Gate试板Sampling压力Pressure倒圆Fillet顶棍Ejector顶白Stress Mark粘前模Sticking Cav名称块表Title Block版本标识Revision Level材料清单Stock List斜导柱（斜边）Angle PinA 板A'plateB 板B'plate倒扣Under-Cut披峰Flash缩水Sink Mark氮化Nitride不规章四边形Trapezoid缩水Shrinkage连续的Consecutive雕刻Engrave出模角Draft分模面Parting Surface擦位Shut-Off（S∕0）导套Bushing回针Return Pin加硬Harden唧嘴Sprue设计筒图Design Preliminary丝印Silkprint不干胶Adhesive Sticker导向针Guide Din公差Tolerance线切割Wire-Cut电火花Edm抛光Polishing蚀纹Texture探热针Thermocouple三打螺丝毫（限螺丝）Stripper Bolt盖板Cover Plate齿轮Gear油唧Hydraulic Cylinder司筒Ejector Sleeve导柱Leader Pin冷料# Cold Slag线切割Wire E.D.M.轮廓Contour螺纹孔Tapping Hole连接件Fittings斜针Angle Pin接合Engage替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press水嘴接头Water Fittings螺纹Eyebolt Thread回针Stop Pin二级顶出针Sub-Leader Pin镶件Mold Insert锁定位Lock楔子（铲鸡）Wedge高产量模量High Volume Running Mold 剖面图Cross Section模具结构Mold Construction模芯Parting Core局部视图Partial View热流道Manifold热嘴Hot Nozzle型腔数Cav No模号Mold No胶料Material尺寸Dimension重要尺寸Critical Dimension雕刻Engrave托司EJ.GUIDE PIN。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
1．XXX！你现在有空吗，我可以问你一些问题吗？Could I ask you some questions if you are free?/ Are you free now? May I ask you some questions (a question)?2．请问此产品的面是否为外观面？表面做什么处理？是晒纹/抛光？Can you tell me whether the surface of this part is a visible/esthetic one? What will we do for its surface? Texture or Polishing?3．请问产品这个面可否加顶针或顶块？产品允许加扁顶针吗？Does this part need an ejector pin or an ejector bar? Can we add an ejector blade?4．这个产品的柱位我们打算做司筒。
（或镶针）可以吗？Can we add ejector sleeves or ejector pins in the boss of this part?5．产品的这个位置不能出模，我们打算做行位，在此面上会有分模线，你接受吗？There's an undercut at this position and it needs a slider. It will also have a parting line on this side, is that OK?6．产品里面的这个位置我们打算做斜顶或内行位，有问题吗？We will make the lifter and (inner) slider in this position, will that be a problem?7．你提供的2D产品图与3D产品图不一致，请问以哪一个图面为准？The 2D and 3D drawing you provided is not the same, can you tell me which one is correct? 8．你提供的3D产品图有的地方没有出模角，有的地方胶位太厚，有的地方胶位太溥，这些产品问题我们可以自己修改吗？修改后会给交给你确认。
There is no draft angle in the 3D drawing, some materials are too thick, and some place are too thin. Can we modify this part by ourselves? We will send the drawing to you for you to check after we modify it.9．按你们提供的缩水率千分之五，这个模具的尺寸已经做到了模具图面要求。
但注塑出来的产品不符合你们的产品图。
请确认你们的材料的缩水率是否正确？Accoring to the shrinkage one over two hundred, the mold has been done in the right dimension, but the part falls short to your part drawing, are you sure the shrinkage is right? 10．产品的这个位置太小，导致模具钢料太溥，能够加宽这个位置吗？This position is too small and will make the steel material here too thin, can we widen it here? 11．斜顶与后面的柱位空间太小，斜顶在运动时会干涉到柱子，能移动这个柱子的位置吗？The angular lifter interferes with the boss during ejection. Please consider changing the position of the boss.12．这个筋骨位胶厚太溥，而且高度偏高，注塑时很难填充这个筋位，可以增加这个筋骨位的厚度吗？The rib here is too thin and on the high side, so it will be difficult to fill here when we do the injection, can you inrcease the thickness of this rib?13．你是想将此筋骨位的高度加高/减低吗？加胶的位置我们将用铜公放电加深。
但减胶的位置有两种做法，1、做镶件；2、烧焊；因为镶件的底部有运水，我们简单的做法是烧焊处理，你可以接受吗？Will you increase/decrease the material on this rib? We will use EDM if you add material, but there are two option if you choose to decrease:1.Make inserts;2.Welding, because there is water in the bottom of the insert, is that OK?14．这个样板的筋骨位底部烧焦，是因为排气不良，我们可以在筋骨位的中间增加一个镶件。
This sample has been burned in the bottom because the venting is not good, we can add an insert in the middle of the rib.15．重做镶件大约需要5-6天时间，你能接受吗？It will take about 5 or 6 days to redo the insert, is that OK?16．产品的这个面我们已经做了晒纹处理，如果需要加胶，这个面我们需要重新外发晒纹。
可能需要几天的时间。
所以我们直接以铜公放电的火花纹取代你要求的纹路，你可以接受吗？We have made the texture on this side, if we add material, it will take some days to remake the texture by out-resourcing, so we suggest using the texture by EDM instead, is that OK? 17．模具是用公制/英制的配件？需要备用件吗？Is this mold dimension measured in inches or meters? Does it need spare parts?18．模具上铭牌上的刻字内容是由你们提供吗？你们什么时候可以这些刻字资料。
Will you provide the engraving content of the plate of this mold to us? When will you send it? 19．可否提供此模具生产时，注塑机的型号及相关资料。
如：啤机大小、呵林柱尺寸、顶棍孔尺寸等Can you provide the type of injection machine and other related information of this mold to us? Such as the boss dimension, the hole's dimension of the ejector pin and the size of the injection machine and so on.20．这个问题我需要同其它同事商议会再答复你。
I need to discuss this problem with the other colleagues and then I will reply back to you. 21．我们将尽力达成你的计划，如有异常，会及时通知你。
We will try our best to complete your plan, if there are any complications, we will notify you immediately.22.这个产品的长度为330.12MM,宽度为78.96MM,高度为45MM.胶厚为2MM,重量为70.63g,试模注塑机型号为250吨,胶料颜色为黑色,产品外表面晒纹处理,内表面为抛光.需要日期章、环保章、材料章.前后模用2344氮硬，斜顶和行位座用738H，以上模具信息正确吗？请确认！"The length of this part is 330.12MM, Width is 78.96MM, height is 45MM, thickness is 2MM, weight is 70.63g, the injection machine is 250T,the material is black, the outside of the part has texture, inner side needs polishing, and it also needs a date and recycle stamp,the core&cavity is 2344 nitridng, the lifter and slider shelf is 728H. Please check the information above!" 23．现在到了吃午钣的时间，我们下午再继续好吗？It is time to have lunch, let's discuss this project later this afternoon?24.和滑塊干涉的倒勾請加料填平至滑塊可以順利滑動(The undercut area interferes with the slide block and needs to be filled with material to help the slider move smoothly.)25. 加肉太多(The thickness added is too thick.)26. 加肉面積太大(The thickening area is too wide.)27.GATE位置移位( The gate position is moved.)28. 滑塊拆的位置(The split line of slide block or the area of slide.)29. 此處有尖角，填充困難(It is hard to fill this area due to the sharp feature.)30. 此處鋼材太薄，強度不足而且不容易冷卻(The strength of this area is too weak and it is hard to cool because the steel is too thin.) 31. 圓柱特徵要有一半圓不可以拆在滑塊上，以免粘滑塊造成拉白，拉斷(We avoid designing the semicircle of the cylinder on the slide block because it will be pulled apart or cause drag marks.)32. 此處做斜銷在作動時會削到成品肉厚(The part will be damaged if we make the lifter in this area.)33. 這個面是裝配面，不能加料(This is a critical surface where we cannot add additional material.)34. 此處料位太厚，會有縮水，建議減料改善(Because of the shrinkage of the thickness, we suggest reducing some wall thickness to improve it.)35. 此面是不是外觀面，此處做滑塊的話會有夾線，是否可以接受"(Please confirm whether it is a critical surface or not. Also, confirm whether it is acceptable to have a slide split line if we have a slide in this area. )"36. 此處有倒勾，能否減料，使公母模靠破，不做滑塊和斜銷"(Please confirm whether we can reduce material to the area where we have an undercut as indicated to have shut off on cavity side. No slide block and lifter will be made. )"37. 請盡快確認這種拆模方式和結構，否則會影響模期(Please confirm the issues of Parting line, Gate position...Etc. as soon as possible; otherwise, the lead-time will be extended.)38. 此面是否有特殊要求，能否有頂針印(Please confirm whether it is a critical surface or not and if we can have E.J. pin marks on it.)39. P.L面開在此處，模具上會有尖角和刀口，對模具壽命有影響(There are sharp edges if we set the parting line here, It will reduce the tool life)40. 加大拔模角，以便脫模順利 We suggest enlarging the draft angle to help release the tool.)41. GATE做在此處的話有兩個缺點：1.蓋子打開時可以看到GATE的修剪部位; 2.兩個斜銷在同一側，頂出也不是很平衡.(There are two problems if the gate is to be designed i n this area:a). It is easy to see the gate mark when you open the cap.b). The ejectors are unbalanced when two lifters are on the same side)42. GATE做在此處的話.蓋子打開後看不到GATE的修剪部位(The gate mark is not visible if the gate position is designed like this.)43. 如果GATE一定要做在你們指定的位置的話，那還不如做在這一側，這樣的話還可以減小這個位置的縮水"(If you insist that the gate position has to be like the original design, then we would further recommend to haveit to the area indicated so it can avoid a shrink problem in this area.)"44. 在此處GATE做潛頂針的話，背後的外觀面會有沖料痕，而且成品又是黑色的，會最明顯(If the design of the gate has to be a sub. Gate, then the back surface of the part will have serious flow marks due to the black colour.)22. P.L開在此處不合理，模具加工困難，P.L應改為和圖示的一樣"(This area is not suitable to have a Parting line because the tool will become more complicated; therefore, we recommend to have the Parting line as indicated.)"45。