高速光电敏传感器规格书

合集下载

光电传感器产品参数说明书

Photoelectric Sensors2.144BMOA Miniature Remote Amplifier SensorsNeed the precision of a laserphotoelectric sensor, but have no room to mount something that big? Ultra miniaturesensing heads down to 2 mmcan fit into applications wheremost sensors won’t. The BMOA component systems use an amplifier to power and control the signals from the sensing head, making it a unique alternative to typical fiber optic solutions. The BMOA component systems offer maximum flexibility with high flex cable versions for moving applications likerobotic arms. The systems can detect targets as small as 0.05 mm. The BMOAamplifiers make set-up and operation easy, using a simpledynamic teach function, or amanual push-button adjustment mode. Available in economical discrete or advanced analog outputversions to solve difficult applications.Features– Smallest sensing head in the industry– Laser-like precision to detect targets as small as 0.05 mm – High speed switching up to 5 kHz– 50 ms pulse stretching delay – Simple pushbuttonadjustment of dynamic teach function– Stability and Output Function LEDs– Discrete output versions PNP and NPN– Analog Output versions 0…10 Vdc and 4…20 mA – Din-rail or panel mountable Applications– Thread detection – Small part profiling – Robotic end-effectors– Semiconductor component detection– High performance alternative to fiber opticsBMOAMiniature Remote Amplifier SensorsBMO A01... amplifiers only.C o u r t e s y o f C M A /F l o d y n e /H y d r a d y n e ▪ M o t i o n C o n t r o l ▪ H y d r a u l i c ▪ P n e u m a t i c ▪ E l e c t r i c a l ▪ M e c h a n i c a l ▪ (800) 426-5480 ▪ w w w .c m a f h .c o m2.145t p76o amplifier connectoramplifier connectoramplifier connectorC o u r t e s y o f C M A /F l o d y n e /H y d r a d y n e ▪ M o t i o n C o n t r o l ▪ H y d r a u l i c ▪ P n e u m a t i c ▪ E l e c t r i c a l ▪ M e c h a n i c a l ▪ (800) 426-5480 ▪ w w w .c m a f h .c o mPhotoelectric Sensors2.146High SpeedBMO A01-I-PU-C-02BMO A01-I-NU-C-02SeriesDiscrete Output PNP Normally-open NPNNormally-open Analog Output 0...10 Vdc 4...20 mASupply VoltageVoltage Drop U d at I e Output Current (digital)Analog Output Type (Voltage)Analog Output Type (Current)Analog Output Load (voltage) min load Analog Output Load (current) Max Load Current Consumption I o (no load)Protections Response TimeSwitching FrequencyPulsed/Non-Pulsed Light Source Output FunctionOperating Temperature Range Degree of Protection per IEC 60529Sensitivity/Range Adjustment Power/Stability Indication Alarm Indication Output LEDHousing MaterialWeightConnection (to control system)10…30 Vdc< 2 V 100 mA 45 mAShort Circuit, Reverse Polarity100 µs 5 KHz Non-PulsedLight/Dark Selectable -10° C to +55° CIP 65Teach-in and ManualGreen LED Yellow LED ABS 55 g2 m PVC Cable ,3 x 26 AWGq w e rBMOAMiniature Remote Amplifier SensorsSensitivity settingAUT – the amplifier will determine the best setting for the application.MAN – this allows you to fine-tune the settings or manually adjust the sensor for difficult applications.Wiring DiagramsOutput GNDOutput GNDrC o u r t e s y o f C M A /F l o d y n e /H y d r a d y n e ▪ M o t i o n C o n t r o l ▪ H y d r a u l i c ▪ P n e u m a t i c ▪ E l e c t r i c a l ▪ M e c h a n i c a l ▪ (800) 426-5480 ▪ w w w .c m a f h .c o mFiber Optics/photoelectricObject Resolution for Diffuse Sensors42-2-4-6-8Y(mm)055M, 06TM & 66RMYMeasuring Arrangement:900a standard resolution amplifier.04SM, 05TM & 66RMthe beam at certain ranges.Sensing Distance for Diffuse Sensors0.8% 1.6% 3.1% 6.3% 12.5% 25% 50% 100%Absolute Mode (ABS)This mode offers the maximum accuracy for allapplications. The amplifier will offer 8 stages ofCourtesyofCMA/Flodyne/Hydradyne▪MotionControl▪Hydraulic▪Pneumatic▪Electrical▪Mechanical▪(8)426-548▪www.cmafh.co m。

CITIZEN 电子 CITISENSOR PR-40-T 光电传感器规格说明书

9. Precautions 9-1. Soldering(1) Manual Soldering1) Solder with silver content is recommended.2) As to CITISENSORs that have absorbed moisture by any chance, baking isrecommended prior or the soldering process to prevent CITISENSORs from the possible crack problem due to the absorbed moisture.3) The use of the soldering iron in less than 25W and the temperature of iron tip must be kept at no higher than 350°C.4) Force or stress must not be applied to the resin portion while soldering. 5) It is requested to solder each land within 3 seconds.6) It is requested that products should be handled after their temperature has dropped down to the normal room temperature.(2) Reflow soldering1) Following soldering paste is recommended Melting temperature: 178 ~ 192°C. Composition: Sn 63 %, Pb 37 %2) The temperature profile at the top surface of the parts is recommended as shown below.3) It is requested that products should be handled after their temperature has dropped down to the normal room temperature.(3) Lead free soldering1) Following soldering paste is recommended Melting temperature: 216 ~ 220°C.Composition: Sn 3.5Ag 0.75Cu2) The temperature profile at the top surface of the parts is recommended as shown below.3) It is requested that products should be handled after their temperature has dropped down to the normal room temperature.Reflow soldering of the above profile is allowed two times.ApprovedCheckedDrawnSymbol CITISENSORNamePR-40140~160°C4°C sec.Max10sec.Max240°C Max More than 1min.T e m p e r a t u r eTime4°C /sec.Max140sec160~180°C4°C /sec.MaxT e m p e r a t u r eTime4°C /sec.Max260°C Max 220°C60~70secReferenceAug.22,2007M.Okuwaki9-2. CleaningPerform the cleaning after soldering strictly in conformity to the following conditions:· Cleaning Agent : Alcohol· Temperature and Time: 30 seconds under the temperature below 50°C or 3 minutes below 30°C.· Ultrasonic Cleaning : 300W or less9-3. Other Precaution1) It is requested to avoid any stress added to the resin portion while heating.2) It is requested to avoid any friction by sharp metal nail etc. to the resin portion. 10. Precautions on Designing1) The Current limiting Resistor should be placed on the circuit to drive within the rating. Also the design should be done to avoid the reverse voltage (over-current) applied instantaneously when turned ON or OFF .2) When the Pulse Driving Current is applied, the average current consumptionshould be within the rating. Also the design should be done to avoid the reverse voltage applied when put off.3) Recommended Soldering Pattern<For Reflow Soldering>The above dimensions are recommended,but the mountability study should be conducted in advance at your site.4) When assembling the circuit board into the finished products, pay attention to avoid the component parts from touching with other parts.ApprovedChecked DrawnSymbol CITISENSORNamePR-40ReferenceAug.22,2007M.Okuwaki0.60.60.60.60.30.375。

EE-SX3160-W11 4160-W11 9.5毫米宽的透光光敏传感器说明书

152EE-SX3160-W11/4160-W11 Photomicrosensor (Transmissive)■DimensionsNote:All units are in millimeters unless otherwise indicated.■Features•Wide model with a 9.5-mm-wide slot.•Light-receiving element and amplification circuits contained in one chip.•Can use a power supply voltage of 4.5 to 16 V.•Connects directly to C-MOS or TTL.•Dark-ON Sensor: EE-SX3160-W11•Light-ON Sensor: EE-SX4160-W11•Pre-wired Sensors (AWG28).•Solder-less lead wire connection to increase reliability.■Absolute Maximum Ratings (Ta =25︒C)Note:1.Refer to the temperature rating chart if the ambient tem-perature exceeds 25︒C.2.If you mount the Sensor with screws, use M3 screws, and flat washers and use a tightening torque of 0.5 N·m max.■Electrical and Optical Characteristics (Ta = 25︒C)ItemSymbol Rated value EmitterForward current I F 50 mA(see note 1)Reverse voltageV R 4 V DetectorPower supply volt-ageV CC 16 V Output voltage V OUT 28 V Output currentI OUT16 mA Permissible output dissipationP OUT 250 mW (see note 1)Ambient tem-peratureOperating T opr –25︒C to 75︒C StorageTstg–25︒C to 85︒CItemSymbol ValueConditionEmitterForward voltage V F1.2 V typ., 1.5 V max.I F = 20 mA Reverse current I R 0.01 μA typ., 10 μA max.V R = 4 V Peak emission wave-lengthλP 920 nmI F = 20 mADetectorLow-level output volt-ageV OL 0.12 V typ., 0.4 V max.V CC = 4.5 to 16 V , I OL = 16 mA, I F = 0 mA (EE-SX3160), I F = 10 mA (EE-SX4160)High-level output volt-ageV OH 15 V min.V CC = 16 V , R L = 1 k Ω, I F = 10 mA (EE-SX3160), I F = 0 mA (EE-SX4160)Current consumptionI CC3.2 mA typ., 10 mA max.V CC = 16 V Peak spectral sensitivi-ty wavelengthλP 870 nmV CC = 4.5 to 16 V LED current when output is OFF I FT2 mA typ., 10 mA max.V CC = 4.5 to 16 VLED current when output is ON Hysteresis∆H 15% typ.V CC = 4.5 to 16 V (see note 1)Response frequency f 3kHz min.V CC = 4.5 to 16 V , I F = 15 mA, I OL = 16 mA (see note 2)Response delay time t PLH (t PHL ) 3 μs typ.V CC = 4.5 to 16 V , I F = 15 mA, I OL = 16 mA (see note 3)Response delay timet PHL (t PLH )20 μs typ.V CC = 4.5 to 16 V , I F = 15 mA, I OL = 16 mA (see note 3)Be sure to read Precautions on page 24.EE-SX3160-W11/4160-W11 Photomicrosensor (Transmissive) 153ineerin g Data2.1 mm0.5 mm0.5 mmDiskInp u t O u tp u tInp u t O u tp u tEE-SX3160EE-SX416040Dissipation Temperature RatingVoltage Characteristics (Typical)Low-level Output Voltage vs. Output Current (Typical)Response Delay Time vs. Forward Current (Typical)Repeat Sensing Position Characteristics (Typical)L o w l e v e l o u t p u t v o l t a g e V O L (V )C u r r e n t c o n s u m p t i o n I c c (m A )S u pply v oltage V CC (V )V CC = 5 VI F = 0 mA (15 mA)I OL = 16 mAI OL = 5 mAT a = 25°CI F = 0 mA (15 mA)Am b ient temperat u re Ta (°C)For w ard v oltage V F (V )F o r w a r d c u r r e n t I F (m A )F o r w a r d c u r r e n t I F (m A ))I F = 0 mA (15 mA)V CC = 5 VT a = 25°C T a = −30°C T a = 25°C T a = 70°CO u tp u t c u rrent I C (mA)Am b ient temperat u re Ta (°C)LED Current vs. Ambient Tempera-ture Characteristics (Typical)。

光电感应传感器产品参数说明说明书

> 25 mm
–35...+65 °C 130 mm 130 mm 155 mm 100 mm 100 mm 50 mm
/photoelectric
6Connectors 7Accessories oProduct
Overview
t Technical Reference
> 5 mm
–40...+60 °C 110 mm 110 mm 135 mm 70 mm 70 mm 30 mm
> 25 mm > 15 mm –35...+65 °C 130 mm 130 mm 155 mm 80 mm 80 mm 40 mm
M4-Threaded Flexible Tip 2×1 mm
10.5
15
Ø2.2
2xØ1.0
BFO D10-XA-HB-EAK-10-02 BFO D10-XA-RB-EAK-10-02 BFO D13-XB-RB-EAK-10-02 BFO D10-XA-GB-EAK-10-02 BFO D13-XA-JB-EAK-20-02
> 15 mm > 10 mm –55...+70 °C 50 mm 50 mm 75 mm 20 mm 20 mm 10 mm
> 15 mm
–55...+70 °C 50 mm 50 mm 75 mm 20 mm 20 mm 10 mm
> 5 mm
–40...+60 °C 60 mm 60 mm 85 mm 35 mm 35 mm 20 mm
> 15 mm >10 mm –35...+65 °C 50 mm 50 mm 75 mm 20 mm 20 mm 10 mm

光敏传感器产品说明说明书

DatasheetDiffuse or Retroreflective Sensor for Error Proofing of Bin-Picking Operations•One-component system, easy to mount and even easier to use. Automatically operates in either diffuse or retroreflective mode, depending on the application•Automatic setup and adjustment; wide beam pattern provides easy alignment•Range up to 2 m (6.5 ft) when used with retroreflective target; 400 mm (15.7 in) when used in diffuse mode •Large job lights on either side of the metal housing can be remotely controlled to initiate user action with a solid or a blinking green light; job lights turn red to indicate bin-picking errors •Compact package size; only 30 mm wide × 15 mm deep (1.2 in × 0.6 in)•Available in 2 lengths to fit existing parts bin sizes and configurations•Easy DIP-switch adjustments: PNP/NPN output, normally open/normally closed operation, solid/flashing job light, and gate polarity for job light activation •Two LEDs indicate power ON and output ON•Choose 2 m (6.5 ft) unterminated cable or 2 m (6.5 ft) cable with 5-pin Euro-style quick-disconnect connector•Heavy-duty protective brackets available •12 V dc to 30 V dc operationWARNING: Not To Be Used for Personnel ProtectionNever use this device as a sensing device for personnel protection. Doing so could lead to serious injury or death. This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition.ModelsOverviewThe PVD Series Parts Verification Sensor is a one-component, easy-to-use light screen suited to many part assembly, bin picking (pick-to-light), and error-proofing applications. The PVD increases task efficiency due to simplified job training, increased quality control (no skipped components), and reduced rework and inspections. It speeds the resumption of work after breaks and other distractions, and is ideal for multilingual workplaces where communication is an issue.The PVD self-contained, solid-state emitter/receiver array is capable of functioning in either diffuse or retroreflective sensing mode. Noconfiguration is required for this selection. If a retroreflective target is installed opposite the sensor, it will function in retroreflective mode. If not, it will function in diffuse mode. The sensor’s ongoing self-adjustment feature requires no user adjustment; the sensor adapts to the sensing conditions after 15 seconds when blocked. Sensor range decreases when no retroreflector is installed.The DIP-switch-selectable PNP/NPN output interfaces to a system controller, which is pre-programmed for a specific sequence of tasks.Mounted with its visible red beams stretching across each parts bin, the sensor job light signals the assembler which bins contain items to be picked in a given operation and in what order they should be picked.As the assembler takes a part in sequence and breaks the beam, the sensor senses that the part was removed and it sends an output signal to the controller. The controller then verifies if the correct part was taken and may respond by turning that job light OFF, activating the job light of the next bin in the sequence. If the assembler reaches into a bin out of sequence, the PVD turns on its output to signal the system controller and turns on its red job light to signal the assembler that an incorrect pick has occurred.Standard configuration options are selected by means of a bank of four DIP switches behind a press-on black rubber cover. DIP switch options include: PNP or NPN output, Normally Open or Normally Closed operation, steady or flashing job light, and job light control input.•To order the 150 mm (6 in) cable model with a quick disconnect, add the suffix "W/6IN" to the cabled model number. For example,PVD100Q W/6IN.•Models with a quick disconnect require a mating cordset.PVD Series Parts Verification SensorOriginal Document 113230 Rev. G4 August 2016113230Figure 1. Sensor features10 mm20 mm30 mm40 mm50 mm60 mm70 mm80 mm90 mm100 mm110 mm2.5 m2 m1.5 m1 m0.5 mRangeMinimumObjectSizetoAlwaysBlockaBeamFigure 2. Minimum object detection size (retroreflective operation)InstallationMultiple sensors located farther than the sensor's maximum range from one another are unlikely to cause crosstalk problems. However, when multiple sensors are mounted in a confined area, take care to avoid crosstalk between them. Alternate the relative position of adjacent sensors and/or reflectors. Sensors positioned above or below one another should not create crosstalk difficulties. Mount the sensor and reflector parallel.Figure 3. Examples of Appropriate Positions Figure 4. Example of Incorrect Position - Tel: +1-763-544-3164P/N 113230 Rev. GMountingThe wide beam pattern of PVD sensors simplifies their alignment. M4 stainless steel fasteners and two stainless steel brackets are included with each sensor.Mount the sensor and its reflector, if used, parallel to one another in the same plane, and their tops and bottoms aligned.1.From a common point of reference, make measurements to locate the sensor and itsreflector, if used, in the same plane with their midpoints directly opposite each other.2.Mount the included brackets to the top and bottom of each sensor, as shown.3.Mount the sensor in its brackets and the reflector, if used, being careful to position thesensor's red lenses directly facing the reflector.4.Measure from one or more reference planes (for example, the building or bin floor) to thesame point(s) on the emitter and receiver to verify their mechanical alignment. (If the sensors/reflectors are mounted exactly vertical or horizontal, a carpenter’s level may be helpful. A straightedge or a string extended between the sensor and the bin wall may also be helpful.)5.Also check “by eye” for line-of-sight alignment.6.Make any necessary final mechanical adjustments, and hand-tighten the bracket hardware.7.After the electrical hookup is complete, check for beam alignment. If necessary, re-align theemitter and receiver at that time.Figure 5. PVD MountingHardwareWiringAll models feature integral 2 m (6.5 ft) long, 3.3 mm (0.13 inch) diameter PVC-jacketed cables. Models whose model numbers end in “Q”are terminated with quick-disconnect (QD) Euro-style 5-pin connectors; other models have unterminated ends. Optional mating QD cables are available. Either 4-pin or 5-pin QD cables may be used; the center pin of a 5-pin cable (gray wire, pin 5) is unused in normal operation.Wiring is functionally identical for cabled and quick-disconnect models.NPN (Sinking) OutputPNP (Sourcing) OutputKey–+–+1 = Brown2 = White3 = Blue4 = Black5 = GraySee Configuration on page 3 for job light control input requirements.ConfigurationTo configure the PVD, set the DIP switches as shown, using the supplied plastic screwdriver to avoid damaging the switches or causing a short circuit.P/N 113230 Rev. G - Tel: +1-763-544-31643The switches determine four status operating modes:Status Indicators/Troubleshooting - Tel: +1-763-544-3164P/N 113230 Rev. GSpecificationsSupply Voltage and CurrentInput Voltage: 12 V dc to 30 V dc (10% maximum ripple at 10% duty cycle)Input Current: less than 88 mA at 12 V dc, less than 75 mA at 24 V dc and less than 72 mA at 30 V dc (exclusive of load)Supply Protection CircuitryProtected against reverse polarity and transient overvoltages Sensing BeamVisible red, 630 nmSensing RangeRetroreflective applications: 2 m (6.5 ft) using 25 mm (1 in) wide retroreflective tapeDiffuse applications: 400 mm (15.7 in) with 18% reflectivity gray card target Sensing Height4-channel models: 111 mm (4.4 in)8-channel models: 240 mm (9.4 in)Beam Spacing28.6 mm (1.125 in)Output ConfigurationUser-selectable via DIP switch:1 open-collector PNP (current sourcing) or 1 open-collector NPN (current sinking)Output Rating150 mA maximumOFF-state leakage current: less than 10 microampsON-state saturation voltage: NPN — less than 1 V dc at 150 mA; PNP — less than 2 V dc at 150 mARequired Overcurrent ProtectionWARNING: Electrical connections must be made by qualified personnel in accordance with local and national electrical codes and regulations.Overcurrent protection is required to be provided by end product application per the supplied table.Overcurrent protection may be provided with external fusing or via Current Limiting, Class 2 Power Supply.Supply wiring leads < 24 AWG shall not be spliced.For additional product support, go to .Output ProtectionProtected against false pulse on power-up and short circuit of outputs Output Response Time400 ms (includes standard 100 ms ON-delay and 100 ms OFF-delay)Delay at Power-UpLess than 1.0 secondSensing ResolutionSee Dimensions on page 6 for Minimum Object Detection ZoneRetroreflective: 51 mm at 406 mm range, 100 mm at 2 m (2.0 in dia. at 16 in range, 3.9 in at 6.5 ft); see Figure 2 on page 2Diffuse: 55 mm dia. at 400 mm range (2.16 in at 15.7 in range)IndicatorsGreen LED: Power ON/OFF Yellow LED: Output ON/OFFJob Light (Diffused Green LED): Turned ON and OFF by applying an external signal to the Job input (white wire). The job lights will be active high or active low, depending on DIP switch 4 selection.Error Light (Diffused Red LED): Turned ON and OFF by detection of an output event when job light is not ON.Indicator Light LumensAdjustments4 DIP switches, located behind access panel (default setting is ON position)ConstructionBlack painted aluminum housing; acrylic lenses; thermoplastic polyester end caps; thermoplastic elastomer programming switch cover; stainless steel mounting brackets and hardware Connections5-conductor PVC-jacketed 2 m (6.5 ft) cable which is either unterminated or terminated with a 5-pin Euro-style quick-disconnect connector, depending on model. Cable diameter is 3.3 mm (0.13 in).Environmental RatingNEMA 2; IEC IEC IP62Operating ConditionsTemperature: 0 °C to +50 °C (+32 °F to +122 °F)Humidity: 90% at +50 °C maximum relative humidity (non-condensing)CertificationsP/N 113230 Rev. G - Tel: +1-763-544-31645Dimensions4 x ø4.45 mm (0.175")Cable3.9 mm (0.15")3.9 mm (0.15")1.4 mm SMBPVA1 Standard Bracket (2 Included with PVD)Hardware Included with Each Sensor (kit part number 50532)4 x ø4.6 mm2.0 mm (0.08")10.2 mm (0.40") - Tel: +1-763-544-3164P/N 113230 Rev. GAccessoriesCordsetsBracketsAll measurements are listed in millimeters, unless noted otherwise.Bracket Selection TableNOTE: Standard mounting brackets are included with each PVD System. The following brackets are in addition to the standard brackets.P/N 113230 Rev. G - Tel: +1-763-544-31647Retroreflective TapeBanner Engineering Corp. Limited WarrantyBanner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp.Copyright NoticeAny misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time. For the most recent version of any documentation, refer to: . © Banner Engineering Corp. All rights reserved. - Tel: +1-763-544-3164。

OPTOLOGIC 光敏传感器系列产品说明书

PLASTIC SILICONOPTOLOGIC ®PHOTOSENSORQSE156 QSE157 QSE158 QSE159DESCRIPTIONThe QSE15X family are OPTOLOGIC ® ICs which feature a Schmitt trigger at output which provides hysteresis for noise immunity and pulse shaping. The basic building block of this IC consists of a photodiode, a linear ampliﬁer, voltage regulator, Schmitt trigger and four output options. The TTL/LSTTL compatible output can drive up to ten TTL loads over supply currents from 4.5 to 16.0 volts. The devices are marked with a color stripe for easy identiﬁcation.FEATURES•Bipolar silicon IC•Package type: Sidelooker•Medium wide reception angle, 50°•Package material and color: black epoxy •Matched emitter: QEE113/QEE123•Daylight ﬁlter •High sensitivity•Direct TTL/LSTTL interfacePart Number DeﬁnitionsColor CodeQSE156T otem-Pole, buffer output Red QSE157T otem-Pole, inverter output Y ellow QSE158Open-collector, buffer output Green QSE159Open-collector, inverter output BlueInput/Output TablePart Number Light OutputQSE156On High Off Low QSE157On Low Off High QSE158On High Off Low QSE159On Low OffHighPLASTIC SILICON OPTOLOGIC® PHOTOSENSORQSE156 QSE157 QSE158 QSE159PLASTIC SILICONOPTOLOGIC ® PHOTOSENSORQSE156 QSE157 QSE158 QSE159NOTES:1. Derate power dissipation linearly2.50 mW/°C above 25°C.2. RMA ﬂux is recommended.3. Methanol or isopropyl alcohols are recommended as cleaning agents.4. Soldering iron 1/16" (1.6 mm) minimum from housing.5. λ = 880 nm (AlGaAs).ABSOLUTE MAXIMUM RATINGS (T A = 25°C unless otherwise speciﬁed)ParameterSymbol Rating Unit Operating T emperature T OPR -40 to +85°C Storage T emperatureT STG -40 to +100°C Soldering T emperature (Iron) (2,3,4) T SOL-I 240 for 5 sec °C Soldering T emperature (Flow) (2,3) T SOL-F 260 for 10 sec°C Output Current I O 50mA Supply Voltage V CC 4.0 to 16V Output VoltageV O 30V Power Dissipation (1)PD100mWELECTRICAL / OPTICAL CHARACTERISTICS (T A = –40°C to +85°C, V CC = 4.5 to 16 volts)ParameterSymbolMinTypMaxUnitsTest ConditionsPositive Going Threshold Irradiance (5) Ee (+)0.0250.250mW/cm 2 T A = 25°CHysteresis Ratio Ee (+)/Ee(–) 1.102.00Supply Current I CC— 5.0mA Ee = 0 or .3 mW/cm 2(5) Peak to peak ripple which will cause falsetriggering—2.00V f = DC to 50 MHZQSE156 (BUFFER TOTEM POLE)High Level Output Voltage V OHV CC -2.1—V Ee = .3 mW/cm 2 , I OH = -1.0mA (5) Low Level Output Voltage V OL —0.40V Ee = 0, I OL = 16 mAQSE157 (INVERTER TOTEM POLE) High Level Output Voltage V OH V CC -2.1—V Ee = 0, I OH = -1.0mALow Level Output Voltage V OL —0.40V Ee = .3 mW/cm 2 , I OL = 16mA (5) QSE158 (BUFFER OPEN COLLECTOR) High Level Output Current I OH —100µA Ee = .3mW/cm 2 , V OH = 30V (5) Low Level Output Voltage V OL —0.40V Ee = 0, IOL = 16mAQSE159 (INVERTER OPEN COLLECTOR) High Level Output Current I OH —100µA Ee = 0, V OH = 30VLow Level Output Voltage V OL —0.40V Ee = .3mW/cm 2 , I OL = 16mA (5) QSE156, QSE157Output rise, fall times tr, tf —70nS Ee = 0 or .3 mW/cm 2 , f = 10KHz DC = 50%, R L =360 Ω (5)Propagation delay tphl, tplh 6.0µS QSE158, QSE159Output rise, fall times tr, tf —100nS Ee = 0 or .3 mW/cm 2 , f = 10KHz DC = 50%, R L =360 Ω(5)Propagation delay tphl, tplh6.0µSPLASTIC SILICONOPTOLOGIC® PHOTOSENSORQSE156 QSE157 QSE158 QSE159 Typical Performance Curves - (Sensor Coupled to QEE113 Emitter)PLASTIC SILICON OPTOLOGIC® PHOTOSENSORQSE156 QSE157 QSE158 QSE159PLASTIC SILICON OPTOLOGIC® PHOTOSENSORQSE156 QSE157 QSE158 QSE159LIFE SUPPORT POLICYFAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein:1.Life support devices or systems are devices or systemswhich, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user.2. A critical component in any component of a life supportdevice or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.DISCLAIMERFAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUMEANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.PLASTIC SILICONOPTOLOGIC ® PHOTOSENSORQSE156 QSE157 QSE158 QSE159。

Keyence EY3A-112光电传感器产品说明书

EY3A-112 Multi-beam Sensor (1 Beam: 125 mm) 13■DimensionsNote:All units are in millimeters unless otherwise indicated.■Features•Ensures higher sensitivity and external light interference resistivity than any other photomicrosensor.•Narrow sensing range ensures stable sensing of a variety of sens-ing objects.■Absolute Maximum Ratings (Ta =25°C)Note:Make sure there is no icing or condensation when operating theSensor.■Electrical and Optical Characteristics (Ta = 0°C to 65°C)Note:1.These conditions are for the sensing of lusterless paper with an OD of 0.6 maximum located at the correct sensing position of the Sensoras shown in the optical path arrangement on page page 14.2.These conditions are for the sensing of the paper supporting plate with an OD of 0.05 located using the glass plate without paper as shown in the optical path arrangement on page page 14.3 0−0.2dia.Two, 10 dia.Positioning bossCenter of detector53325-0310 (Japan Molex)Center of emitterPin no.13.2+0.20dia.C1ItemSymbol Rated valuePower supply voltage V CC 7 V Load voltageV OUT 7 VLoad current I OUT10 mA Ambient tem-peratureOperating Topr 0°C to 65°C StorageTstg–15°C to 70°CItemValueConditionPower supply voltage 5 V ±5%---Current consumption 50 mA max.V CC = 5 V , R L = ∞Peak current consumption 200 mA max.V CC = 5 V , R L = ∞Low-level output voltage 0.6 V max.V CC = 5 V , I OL = 4 mA (see note 1)High-level output voltage3.5 V min.V CC = 5 V , R L =4.7 k Ω (see note 2)Response delay time (High to Low)35 ms max.The time required for the output to become “Lo” after placingsensing object.Response delay time (Low to high)20 ms max.The time required for the output to become “Hi” after removing sensing object.Dimensions Tolerance 3 mm max. ±0.33 < mm ≤ 6 ±0.3756 < mm ≤ 10 ±0.4510 < mm ≤ 18 ±0.5518 < mm ≤ 30 ±0.6530 < mm ≤ 50 ±0.850 < mm ≤ 80±0.95Pin no. Remarks Name 1 O Output (OUT)2V Power supply (Vcc)3GGround (GND)Unless otherwise specified, the tolerances are as shown below.Japan Molex 51090-0300 (crimp connector) 52484-0310 (press-fit connector)Recommended Mating Connectors:14EY3A-112 Multi-beam Sensor (1 Beam: 125 mm)■Characteristics (Paper Table Glass: t = 6 mm max., Transparency Rate: 90% min.)(Ta =0°C to 65°C)Note:1.The data shown are initial data.2.Optical darkness (OD) is defined by the following formula:P IN (mW): Light power incident upon the document P OUT (mW): Reflected light power from the document■Optical Path Arrangement■Engineering DataItemCharacteristic valueSensing density Lusterless paper with an OD of 0.6 max. (sensing distance: 125 mm) (see note)Non-sensing distance 185 mm (from the top of the sensor), OD: 0.05Paper sensing distance 125 mm (from the top of the sensor)Ambient illuminationSunlight: 3,000 l x max., fluorescent light: 2,000 l x max.13 dia.4 dia.185 min.(beam diameter)(beam center)Paper supporting plate Glass125 (standard value)8.5(beam center)Distance Characteristics (Estimated Lower-limit Value)Distance (mm)O D (v a l u e )4.75 V5.0 V 5.25 V。

光电传感器数据手册说明书

DatasheetMiniature self-contained photoelectric sensors in universal housing•Bright, visible red (640 nm) light source•Standard models available with 4-wire 2 m (6.5 ft) or 9 m (30 ft) cable or 3 or 4-wire 150 mm (6 in) pigtail with Pico-style M8 threaded connector•Solid-state, bipolar outputs: one current sourcing (PNP) and one current sinking (NPN) standard on 4-wire models•Single output solid-state PNP or NPN standard on Q3 models •Light Operate (LO) or Dark Operate (DO), depending on model•Models available with PFA chemical-resistant jacket (1200 psi washdown rated)for use in harsh environments•Compact 8 mm (0.31 in) housing mounts almost anywhere•Crosstalk avoidance circuitry for applications with multiple sensors•LED status indicators for Power ON, Output Overload, Signal Received, and Marginal Signal•Advanced ASIC technology makes sensor resistant to optical and electrical noise sourceStandard ModelChemical-ResistantModelWARNING:•Do not use this device for personnel protection•Using this device for personnel protection could result in serious injury or death.•This device does not include the self-checking redundant circuitry necessary to allow its use inpersonnel safety applications. A device failure or malfunction can cause either an energized (on) or de-energized (off) output condition.Chemical-Resistant ModelsWORLD-BEAM ® Q12 Series SensorOriginal Document 119223 Rev. M7 April 2020119223Standard Modelssuffix W/30 to the model number. For example, Q126E W/30.•To order the 150 mm (6 in) cable with a 4-pin M8/Pico-style (M8 threaded) QD model, add the suffix Q to the model number. For example, Q126EQ.•To order the 150 mm (6 in) cable with a 4-pin M12/Euro-style QD model, add the suffix Q5 to the model number. For example Q126EQ5.3Retroreflective range is specified using one model BRT-60X40C retroreflector. Actual sensing range may be more or less than specified, depending upon efficiency and reflective area of the retroreflector(s) used. - Tel: + 1 888 373 6767P/N 119223 Rev. MIndicator Features1 - Amber and green LEDs•Green on: power to sensor is on •Amber on: received signal•Amber flashing: marginal signalChemical-Resistant models: LEDs are visible through translucent PFA jacket. Rated to 1200 psi washdown.WiringEmitters have no connection to black and white.CAUTION: Observe proper ESD precautions (grounding) when connecting QD models.Emitters–+Bipolar Models, Light Operate–+PNP Models, Light OperateNPN Models, Light Operate–+Bipolar Models, Dark Operate–+PNP Models, Dark OperateNPN Models, Dark Operate–+Key1 = Brown2 = White3 = Blue4 = Black3-pin M8/Pico-style Male QD 4-pin M8/Pico-style Male QD 34-pin M12/Euro-style Male QDSpecificationsSupply Voltage and Current10 to 30 V dc (10% maximum ripple) at 20 mA maximum current Sensing Beam640 nm visible redSupply Protection CircuitryProtected against reverse polarity and transient voltagesOutput ConfigurationBipolar (1 NPN and 1 PNP) solid-state output or Single output (PNP or NPN), LO or DO, depending on model Repeatability125 microseconds Switching FrequencyOpposed Mode: 385 Hz LP/LV Mode: 715 Hz FF Mode: 590 HzP/N 119223 Rev. M - Tel: + 1 888 373 67673Output Protection CircuitryProtected against false pulse on power-up, short-circuit protectedOutput Response TimeOpposed Mode: 1.3 ms ON; 900 µs OFF LP/LV Mode: 700 µs ON/OFF FF Mode: 850 µs ON/OFFNOTE: 120 ms delay on power-up; outputs do not conduct during this time.IndicatorsOne Yellow and one Green LED (see Figure 1)ConstructionPolarized Retro Models: Thermoplastic elastomer housing with glass lens All Other Standard Models: Thermoplastic elastomer housing with polycarbonate lensChemical-Resistant Models: Housing encased in PFA jacket; cable encased in 3/16 in O.D. PFA tubing Output RatingsOFF-state leakage current:NPN: 10 µA PNP: 10 µAON-state saturation voltage:NPN: 2 V at 50 mA PNP: 2 V at 50 mAVibration and Mechanical ShockAll models meet MIL-STD-202F, Method 201A (Vibration: 10 Hz to 60 Hz maximum, 0.06 inch (1.52 mm) double amplitude, 10G maximumacceleration) requirements. Also meets IEC 60947-5-2 (Shock: 30G 11 ms duration, half sine wave) requirements.ConnectionsStandard Models: 2 m (6.5 ft) or 9 m (30 ft) attached PVC cable, or 150 mm (6 in) pigtail with M8 or M12 threaded connection, depending on the model orderedChemical-Resistant Models: 2 m (6.5 ft) cable encased in 3/16 in O.D. PFA tubing Environmental RatingStandard Models: IEC IP67Chemical-Resistant Models: IEC IP67 (NEMA6) and PW12 1200 psi washdown per NEMA ICS5, Annex F-2002ConditionsOperating Temperature: –20 °C to +55 °C (–4 °F to +131°F)Storage Temperature: –30 °C to +75 °C (–22 °F to +167 °F)95% at +50 °C maximum relative humidity (non-condensing)Certifications(Chemical-resistant models are not UR/UL approved.)Required Overcurrent ProtectionWARNING: Electrical connections must bemade by qualified personnel in accordance with local and national electrical codes and regulations.Overcurrent protection is required to be provided by end product application per the supplied table.Overcurrent protection may be provided with external fusing or via Current Limiting, Class 2 Power Supply.Supply wiring leads < 24 AWG shall not be spliced.For additional product support, go to .Dimensions15.0 mm 4.7 mm (0.19")Polarized RetroModelsM3 mounting screws included(0.31")12.4 mm (0.49")max. torque 0.9 Nm (8 in-lbf)Figure 1. Standard Models - Tel: + 1 888 373 6767P/N 119223 Rev. MMounting hardwarenot included2 m (6.5')* When mounting by running a screw throughboth flanges without support between the flanges,Figure 2. Chemical-Resistant ModelsPerformance Curves - Opposed ModePerformance Curves - Retroreflective ModePerformance is based on the use of a model BRT-60X40C retroreflector.P/N 119223 Rev. M - Tel: + 1 888 373 67675Performance Curves - Fixed-FieldFocus and spot sizes are typical. Performance based on use of 90% reflectance white test card.*AccessoriesCordsets - Tel: + 1 888 373 6767P/N 119223 Rev. MBracketsSMBQ12T•Right-angle bracket•20-ga. 300 series stainless steelHole center spacing: A to B = 7.6Hole size: A = 3.5 x 8.1, B=ø 3.2SMBQ12A•Adjustable right-anglebracket•20-ga. 300 series stainless steelHole center spacing: A to B = 7.6Hole size: A = 3.5 x 8.1, B=ø 3.2Sensor Status IndicatorsP/N 119223 Rev. M - Tel: + 1 888 373 67677AperturesOpposed-mode sensors (standard models only) may be fitted with apertures to narrow or shape the sensor’s effective beam to more closely match the size or profile of the objects being sensed. A common example is the use of “line” (or “slot”) type apertures to sense thread.Note: The use of apertures will reduce the sensing range (see table below).Banner Engineering Corp. Limited WarrantyBanner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time. Specifications and product information in English supersede that which is provided in any other language. For the most recent version of any documentation, refer to:.For patent information, see /patents.FCC Part 15 and CAN ICES-3 (B)/NMB-3(B)This device complies with part 15 of the FCC Rules and CAN ICES-3 (B)/NMB-3(B). Operation is subject to the following two conditions:1.This device may not cause harmful interference, and2.This device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules and CAN ICES-3 (B)/NMB-3(B). These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:•Reorient or relocate the receiving antenna.•Increase the separation between the equipment and receiver.•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.•Consult the manufacturer.© Banner Engineering Corp. All rights reserved。

高性能光电传感器数据手册说明书

Datasheet•Advanced one-piece photoelectric sensors with outstanding optical performance and extremely rugged design•90 V AC to 250 V AC•Protected solid-state relay output; 300 mA maximum load at up to 250 V AC•Multiple sensing modes include: opposed, diffuse, retroreflective and convergent, plus glass and plastic fiber optic models •Selectable light/dark operate•Versatile plug-in modules available for output timing logic and/or signal strength display •Highly visible Power, Signal (AID ™ System 1), and Output indicator LEDs•Choice of prewired 2 m (6.5 ft) or 9 m (30 ft) unterminated cable, plus Mini-style or Micro-style quick-disconnect fittings •Versatile mounting options•Designed to withstand 1200 psi washdown; exceeds its NEMA 6P and IEC IP67 ratingWARNING:•Do not use this device for personnel protection•Using this device for personnel protection could result in serious injury or death.•This device does not include the self-checking redundant circuitry necessary to allow its use inpersonnel safety applications. A device failure or malfunction can cause either an energized (on) or de-energized (off) output condition.ModelsTo order the 9 m (30 ft) PVC cable model, add the suffix "W/30" to the cabled model number. For example, Q452E W/30. A model with a quick disconnect (QD) connector requires a mating cable.Opposed-Mode Emitter (E) and Receiver (R) ModelsBecause of their extremely high excess gain, these opposed-mode sensors are an excellent option for sensing in contaminated or dirty areas, and are also the best choice for long-range sensing. Sensingbeam: Infrared, 880 nmRetroreflective-Mode ModelsThe visible red sensing beam of these sensors makes them very easy to align. Model Q45BW22LP polarizes the emitted light and filters out unwanted reflections, makingsensing possible in applications otherwise considered unsuited to retroreflective sensing.Performance is specified using the model BRT-3 3-inch reflector (go to for more information). Sensing beam: Visible red, 680 nmQ45BW22 Series SensorOriginal Document 37209 Rev. G30 January 202037209Diffuse-Mode ModelsThese diffuse-mode models detect objects by sensing the reflection of their own emitted light.Ideal for use when the reflectivity and profile of the object to be sensed are sufficient to return alarge percentage of emitted light back to the sensor. Model Q45BW22DX is the first choice fordiffuse-mode applications when there are no background objects to falsely return light. Sensingbeam: Infrared, 880 nmConvergent-Mode ModelsThese sensors are ideal for reflective sensing of very small parts or profiles, and can accurately sensethe position of parts approaching from the side. Ignores all but highly reflective objects that are outsideof the sensing range. Sensing beam: Visible red, 680 nm - Tel: + 1 888 373 6767P/N 37209 Rev. GGlass Fiber-Optic ModelsThese models are an excellent choice for glass fiber optic applications where faster sensor response is not important. Their high excess gain means that opposed individual fibers can operate reliably in many very hostileenvironments. Also, special miniature bifurcated fiber optic assemblies with bundle sizes as small as 0.5 mm (0.020 in) dia. may be used successfully for diffuse-mode sensing when using sensor model Q45BW22F(Q). For more information on compatible glass fiber optics, go to .Plastic Fiber-Optic ModelsLower in cost than glass fiber optics, plastic fiber optics are ideal for use in situations whereenvironmental conditions allow (for example, low levels of acids, alkalis, and solvents). Most are easily cut to length in the field, and are available in a variety of sensing end styles. For more information on compatible plastic fiber optics, go to . Sensing beam: Visible red, 660 nmOverviewStatus indicator LEDs for power, signal, and output are clearly visible beneath a raised dome in the sensor’s transparent o-ring-sealed polycarbonate cover. Also located beneath the sensor’s o-ring-sealed cover are controls for light/dark operate selection and the sensitivity adjustment.•The power indicator (green) lights when power is applied to the sensor.•The signal indicator (red) lights when the sensor sees its modulated light source and pulses at a rate proportional to the strength of the received light signal; this is the AID ™ Alignment Indicating Device 2.•The output indicator (amber) lights when the sensor’s output is conducting. This indicator is especially useful when a timing logic module is used and signal and output conditions are not concurrent.1.LEDs•Green LED: Power on indicator •Red LED: Signal indicator•Amber LED: Output status indicator 2.Optional LED signal strength display 3.Optional timing adjustment 4.Optional timing adjustment 5.Light/dark operate switchP/N 37209 Rev. G - Tel: + 1 888 373 67673Wiring Diagram–+bn (1)bu (3)90–250 V AC1 = Brown 3 = Blue4 = Black1 = Red and black2 = Red and white3 = Red4 = GreenSpecificationsSupply Voltage and Current90 V AC to 250 V AC (50 to 60 Hz)Average current: 20 mAPeak current: 500 mA at 120 V AC, 750 mA at 250 V AC Supply Protection CircuitryProtected against transient voltagesOutput ConfigurationShort circuit/overload protected FET solid-state relayRepeatabilityOpposed mode: 0.25 millisecondsAll other sensing modes: 0.5 millisecondsResponse time and repeatability specifications are independent of signal strength.AdjustmentsLocated under the sensor’s transparent cover: Light/Dark Operate select switch; and multi-turn Sensitivity control (allows precise sensitivity setting—turn clockwise to increase gain). Optional logic and logic/display modules have adjustable timing functions. - Tel: + 1 888 373 6767P/N 37209 Rev. GOutput RatingContinuous current: 300 mA max. to 50 °C (derate to 200 mA at 70 °C, 5mA/°C)Inrush current: 3 A maximum for 100 milliseconds, 5 A maximum for 1millisecondOff-state leakage current: <100 microamps Saturation voltage: <3 V at 200 mA Output Protection CircuitryManually-resettable output latch-out trips in the event of an output overload or short circuit condition. The green Power LED flashes to indicate the latch-out. To reset the output, remove power to the sensor and load for 5seconds, then restore power.Output Response TimeOpposed mode: 2 milliseconds ON, 1 millisecond OFF All other sensing modes: 2 milliseconds ON/OFFNote: 100 millisecond delay on power-up.Output is non-conducting during this time.Required Overcurrent ProtectionWARNING: Electrical connections must bemade by qualified personnel in accordance with local and national electrical codes and regulations.Overcurrent protection is required to be provided by end product application per the supplied table.Overcurrent protection may be provided with external fusing or via Current Limiting, Class 2 Power Supply.Supply wiring leads < 24 AWG shall not be spliced.For additional product support, go to .ConstructionMolded reinforced thermoplastic polyester housing, o-ring-sealedtransparent polycarbonate cover, molded acrylic lenses, and stainless steel hardware. Q45s are designed to withstand 1200 psi washdown. The base of cabled models has a 1/2-in NPS integral internal conduit thread.IndicatorsIndicator LEDs are clearly visible beneath a raised transparent polycarbonate dome on top of the sensor.Power (green) LED: Lights whenever 90 V ac to 250 V ac power is applied,and flashes to indicate output overload or output short circuitSignal (red) AID ™ System LED: Lights whenever the sensor sees itsmodulated light source, and pulses at a rate proportional to the strength of the received light signalLoad (amber) LED: Lights whenever the output relay is energized Optional 7-element LED: Signal strength display module Environmental Rating NEMA 6P, IEC IP67ConnectionsPVC-jacketed 2 m (6.5 ft) or 9 m (30 ft) cables, or 3-pin Mini-style (“Q” suffix models) or 4-pin Micro-style (“Q1” suffix models) quick-disconnect (QD)fittings are available. QD cables are ordered separately.Operating Conditions–40 °C to +70 °C (–40 °F to +158 °F)90% at +50 °C maximum relative humidity (non-condensing)Application NotesOptional output timing modules are available.CertificationsDimensions2m (6.5') CableExternal thread (M30 x 1.5)hex nut suppliedQD ConnectorP/N 37209 Rev. G - Tel: + 1 888 373 67675Performance CurvesDiffuse-mode performance curves are based on a 90% reflectance white test card. - Tel: + 1 888 373 6767P/N 37209 Rev. Gwhite test card.Convergent mode performance curves are based on a 90% reflectanceP/N 37209 Rev. G - Tel: + 1 888 373 67677Plastic fiber optic Diffuse mode performance curves are based on a 90% reflectancewhite test card.AccessoriesCordsets - Tel: + 1 888 373 6767P/N 37209 Rev. GRetroreflective TargetsBanner offers a wide selection of high-quality retroreflective targets. See for complete information.Note: Polarized sensors require corner cube typeretroreflective targets. Non-polarized sensors may use any retroreflective target.BracketsOutput Timing Logic and Signal Strength Display ModulesQ45 sensors easily accept the addition of output timing logic and signal strength display functions. Display modules have a seven-element display that gives a more precise indication of excess gain than does the AID ™ system LED that is standard on Q45sensors. The modules listed below may be used with all Q45BW22 sensors. Refer to the module's datasheet for more information.P/N 37209 Rev. G - Tel: + 1 888 373 67679Banner Engineering Corp. Limited WarrantyBanner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE. This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time. Specifications and product information in English supersede that which is provided in any other language. For the most recent version of any documentation, refer to: .For patent information, see /patents.© Banner Engineering Corp. All rights reserved。

PD70 光电传感器系列产品说明说明书

1Product DescriptionThe PD70sensor family of Photoelectric sensors is specially designed for Doors and Entrance control to meet the requirements in the door market.The slim hous-ing design fits inside the alu-minium frame of e.g.sliding doors.The emitter has a test input to turn it off for evaluation of the sensor function.Available in 10-30VDC version.•Doors and Entrance control •Range 12m•Modulated,infrared light •Supply voltage:10to 30VDC•Output:100mA,NPN or PNP type •Make or break switching•LED for output indication or power supply•Protection:reverse polarity,short circuit,transients •Cable versions or M8connector •Emitter mute•CE and UL325approvedPhotoelectricsThrough-beam,Transistor Output TypePD70CNT12..Type SelectionSpecifications EmitterTestRange Con-Ordering no.Ordering no.Ordering no.Ordering no.Ordering no.S nnec-Receiver Receiver Receiver Receiver Emittertor NPN,NONPN,NCPNP ,NOPNP ,NCMute Low 12mNO PD70CNT12NO PD70CNT12NC PD70CNT12PO PD70CNT12PC PD70CNT12ML Mute Low 12m YES PD70CNT12NOM5PD70CNT12NCM5PD70CNT12POM5PD70CNT12PCM5PD70CNT12M5ML Mute High 12m NO PD70CNT12MH Mute High 12mYESPD70CNT12M5MHNote:Please order emitter and receiver separately2PD70General SpecificationsSpecifications ReceiverOperation DiagramPower supply Target emitter present Object present tv =Power ON delay Installation HintsRelief of cable strainProtection of the sensing faceSwitch mounted on mobile carrierTo avoid interference from inductive voltage/current peaks,separate the prox.switch pow-er cables from any other power cables,e.g.motor,contactor or solenoid cablesIncorrectCorrectThe cable should not be pulledA proximity switch should not serve as mechanical stopAny repetitive flexing of the cable should be avoidedTest active High (MH)Test active Low (ML)3PD70DimensionsExcess Gain110100200E x c e s s G a i n11020Distance (m)Detection DiagramDiastance (m)D i s p l a c e m e n t (m )0,20,40,60,8-0,8-0,6-0,4-0,200910111223456781Delivery Contents•PD70•Packaging:plastic bagWiring Diagram。

1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。

高速光电敏传感器规格书
高速光电敏传感器规格书
一、引言
高速光电敏传感器在现代技术和工业领域起着重要的作用。

作为一种
高灵敏度的光学传感器，它可以精确地检测和测量光信号的强度、频
率和时间。

本文将对高速光电敏传感器的规格进行综合评估，并探讨
其在不同领域的应用。

二、基本原理
高速光电敏传感器利用光敏二极管（Photodiode）的原理来感测光信号。

当光照射到光敏二极管上时，光子会导致光敏二极管内部产生电流。

光照强度越大，产生的电流越强。

传感器还包括电路和信号处理
单元，用于将电流转换为可供读取和分析的数字信号。

三、主要规格
1. 探测器类型：高速光电敏传感器可分为多种类型，包括PIN光二极管、Avalanche光二极管、光电倍增管等。

不同类型的探测器适用于
不同的应用场景。

2. 探测灵敏度：该参数表示传感器对光的感应能力。

传感器的灵敏度
越高，能够探测到的微弱光信号就越多，适用于低光照条件下的应用。

3. 响应时间：响应时间是传感器从接收光信号到输出电信号的时间。

高速光电敏传感器的响应时间通常在纳秒级别，适用于需要快速测量
光信号的应用。

4. 动态范围：动态范围描述了传感器可以测量的光强范围。

较宽的动
态范围使传感器能够在从弱光到强光的广泛范围内精确测量。

5. 工作波长范围：传感器的工作波长范围决定了其对不同波长光的响
应能力。

不同应用场景需要不同波长范围的传感器。

6. 噪音：噪音是指传感器输出信号中的随机波动。

低噪音水平可以提
高传感器的测量精度和稳定性。

四、应用领域
高速光电敏传感器在许多领域都有广泛的应用，包括以下几个方面：1. 科学研究：在物理学、化学和生物学等领域，高速光电敏传感器可
以用于快速测量和分析光学现象，如光谱分析、动力学研究和生物荧
光检测。

2. 通信和信息技术：高速光电敏传感器在光通信和光纤通信中起着重
要作用，可以实现高速数据传输和光网络接口的稳定性和精确性。

3. 工业自动化：传感器可用于高速物体检测、位置检测和运动跟踪等
自动化应用中，提高生产效率和质量控制。

4. 医学诊断：高速光电敏传感器在医学影像学、心电图检测和光学成
像等方面有着重要应用，用于快速捕捉和分析生理信号和组织结构。

5. 雷达和导航系统：用于测量和检测目标的位置、速度和方向等信息，为军事和航空航天领域提供支持。

五、个人观点
高速光电敏传感器作为一种关键的光学测量工具，具有广泛的应用前景。

其高灵敏度、快速响应和较宽的动态范围为各行业的发展提供了重要支持。

随着技术的不断进步，我相信高速光电敏传感器将在更多领域发挥重要作用，并为人们的生活带来更多便利和创新。

六、总结
本文综合评估了高速光电敏传感器的规格和应用，并详细介绍了其基本原理、主要规格以及在不同领域的应用。

通过深入讨论和分析，我们对高速光电敏传感器的工作原理和性能有了更深刻的理解。

个人观点表达了对该技术的认可和未来发展的期待。

随着科技的不断进步，高速光电敏传感器将为人类社会的进步和创新做出更大的贡献。

参考文献：
1. J. Wu, J. Zheng and Y. Song, "High-speed photodetectors among graphene, topological insulator and black phosphorus thin films," Science China Physics, Mechanics & Astronomy, vol. 58, no. 3, 2015.
2. N. J. Smith and X. Zhang, "Optical sensors: Recent advances and future challenges," Journal of Lightwave Technology, vol. 46, no. 12, pp. 1-7, 2018.
3. Y. Liu, C. Zhao and Z. Qiu, "Optical power measurement based
on spatial division multiplexing using a high-speed optical sensor," Photonics Research, vol. 7, no. 3, pp. 258-264, 2019.
4. Y. Chen, H. Wang and Y. Li, "High-sensitivity and high-speed InP/InGaAs photodetectors for optical communication," Optik, vol. 233, 2021.
5. L. Chen, T. Liu and S. C. Wong, "Avalanche photodiodes: Key performance parameters and design considerations," Sensors, vol. 18, no. 6, 2018.。