AP8205A 6.0A 20V TSSOP-8

1General DescriptionThe AP8205A is the highest performance trench N-ch MOSFETs with extreme high cell density, which provide excellent RDSON and gate chargefor most of the small power switching and load switch applications. The meet the RoHS andProduct requirement with full function reliability approved. General FeaturesV DS = 20V I D = 6AR DS(ON) < 27mΩ @ V GS =4.5V R DS(ON) <37mΩ @ V GS =2.5VApplicationBattery protection Load switchUninterruptible power supplyPackage Marking and Ordering InformationG1. Repetitive Rating: Pulse width limited by maximum junction temperature.2. Surface Mounted on FR4 Board, t ≤ 10 sec.3. Pulse Test: Pulse Width ≤ 300μs, Duty Cycle ≤ 2%.4. Guaranteed by design, not subject to production220V N+N-Channel Enhancement Mode MOSFET3VoutFigure 1:Switching Test CircuitT J -Junction Temperature(℃)Figure 3 Power DissipationVds Drain-Source Voltage (V)Figure 5 Output CharacteristicsV INV tFigure 2:Switching WaveformsT J -Junction Temperature(℃)Figure 4 Drain CurrentI D - Drain Current (A)Figure 6 Drain-Source On-ResistanceP D P o w e r (W )I D - D r a i n C u r r e n t (A ）R d s o n O n -R e s i s t a n c e (m Ω)I D - D r a i n C u r r e n t (A )Typical Characteristics4Vgs Gate-Source Voltage (V)Figure 7 Transfer CharacteristicsV Figure 9 Rdson vs Vgs gs Gate-Source Voltage (V)Qg Gate Charge (nC)Figure 11 Gate ChargeT J Junction Temperature ( -℃ ) Figure 8 Drain-Source On-ResistanceFigure 10 Capacitance vs VdsVds Drain-Source Voltage (V)Vsd Source-Drain Voltage (V)Figure 12 Source- Drain Diode Forward5Vds Drain-Source Voltage (V)Figure 13 Safe Operation AreaSquare Wave Pluse Duration(sec)Figure 14 Normalized Maximum Transient Thermal ImpedancePackage Mechanical Data6Attention1,Any and all APM Microelectronics products described or contained herein do not have specificationsthat can handle applications that require extremely high levels of reliability, such as life support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result inserious physical and/or material damage. Consult with your APM Microelectronics representative nearestyou before using any APM Microelectronics products described or contained herein in such applications.2,APM Microelectronics assumes no responsibility for equipment failures that result from using productsat values that exceed, even momentarily, rated values (such as maximum ratings, operating conditionranges, or other parameters) listed in products specifications of any and all APM Microelectronicsproducts described or contained herein.3, Specifications of any and all APM Microelectronics products described or contained here instipulate the performance, characteristics, and functions of the describ ed products in the independent state, and arenot guarantees of the performance, characteristics, and functions of the described products as mountedin the customer’s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer’s products or equipment.4, APM Microelectronics Semiconductor CO., LTD. strives to supply high quality high reliability products. However, any and all semiconductor products fail with some probability. It is possible that theseprobabilistic failures could give rise to accidents or events that could endanger human lives that couldgive rise to smoke or fire, or that could cause damage to other property. When designing equipment,adopt safety measures so that these kinds of accidents or events cannot occur. Such measures includebut are not limited to protective circuits and error prevention circuits for safe design, redundantdesign,and structural design.5,In the event that any or all APM Microelectronics products(including technical data, services) describedor contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law.6, No part of this publication may be reproduced or transmitted in any form or by any means,electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of APM Microelectronics Semiconductor CO., LTD.7, Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. APM Microelectronics believes information herein is accurate andreliable, but no guarantees are made or implied regarding its use or any infringements of intellectualproperty rights or other rights of third parties.8, Any and all information described or contained herein are subject to change without notice due toproduct/technology improvement,etc. When designing equipment, refer to the "Delivery Specification" forthe APM Microelectronics product that you Intend to use.7。