杜邦Hytrel 4056,海翠料,40D硬度TPEE

塑料硬度对照表

塑料硬度对照表 1:塑料硬度对照表 帕氏硬度厚度邵氏硬度测试值平均硬度值 30P 6mm 93-96 °94.5 ° 35P 6mm 87-93 °90 ° 38P 6mm 89-90 °89.5 ° 40P 6mm 88-90 °89 ° 45P 6mm 84-90 °85 ° 50P 6mm 82-83 °82.5 ° 55P 6mm 70-80 °79 ° 60P 6mm 74-76 °75 ° 65P 6mm 73-75 °74 ° 70P 6mm 72-74 °73 ° 75P 6mm 70-70.5 °70 ° 80P 6mm 67-68 °67.5 ° 85P 6mm 64-66 °65 ° 90P 6mm 63-64 °63.5 ° 95P 6mm 58-60 °59 °

100P 6mm 57-59 °58 ° 110P 6mm 54-56 °55 ° 测试温度:23度的测试板材:65456MM 塑料硬度对照表 “PVC 45P”电器插头中,”P”表示硬度。50kgPVC料，可塑剂40kg时是以80P (40/50=80%)，50gPVC料，可塑剂55kg时是以110P(55可塑剂/50PVC料=110%)表示即可塑剂愈多P数愈大PVC胶料P数与硬度对照表

PVC胶料常用硬度对照表 P数（P%）邵氏硬度 （A） 合格范 围 25P98 A±2A 30P97 A±2A 35P95 A±2A 40P92 A±2A 45P90 A±2A 50P88 A±3A 55P84 A±3A 60P80 A±3A 65P77 A±3A 70P75A±3A 75P70 A±3A 80P68 A±3A 85P65 A±3A 90P63 A±4A 95P60 A±4A

物性材料表

特性Feature 耐高温、耐冲击、高流动性、尺寸稳定。High temperature resistance, impact resistance, high liquidity, dimension stability. 用途Use 电子、电器零件、汽车部件等。Electronic, electrical parts, auto parts, etc. 注塑条件Injection conditions 预干燥温度Pre-drying temperature 预干燥时间Pre-drying time 进料区温度Feed zone temperature 压缩区温度Compression zone temperature 熔融区温度Melting zone temperature 喷嘴温度Nozzle Temperature 模具温度Mold 注射压力Injection pressure 物理机械性能Physical and mechanical properties 项目Project 单位unit 试验方法Test method 数值Value 密度Density 熔点Melting point 成型收缩率Mold Shrinkage 吸水率（24小时，23℃）Water Absorption (24 hours, 23 ℃) 熔融指数Melt Index 阻燃等级Flame Rating 拉伸断裂强度Tensile Strength 拉伸模量Tensile modulus 断裂伸长率Elongation at break 弯曲强度Bending 弯曲模量Bending modulus 悬臂梁（无缺口）冲击强度Izod (unnotched) impact strength 悬臂梁缺口冲击强度Izod notched impact strength 洛氏硬度Rockwell hardness 热变形温度（0.45MPa）Heat Deflection Temperature（0.45MPa） Dielectric Strength 绝缘破坏强度 Arc resistance 耐电弧性 Dielectric Constant 介电常数 Dielectric Losses 介电损耗 Characteristics 特性 平衡吸湿量Moisture Absorption at Equilibrium 线性成型收缩率，横向Linear Mould Shrinkage, Transverse 断裂伸长率Elongation at Break 屈服伸长率Elongation at Yield

PA10T材料物性表

P ROVISIONAL D ATA S HEET G RIVORY HT G RIVORY XE 4027 BLACK 9916 Product description Grivory XE 4027 black 9916 is a 30% glass-fibre reinforced flame retardant (UL 94 V-0) engineering thermoplastic material based on a semicrystalline, partially aromatic co-polyamide. Grivory XE 4027 black 9916 is free of halogens and red phosphorus. RoHS: Grivory XE 4027 black 9916 is in compliance with RoHS (2002/95/EC, Re-striction of Hazardous Substances). WEEE:Parts produced from Grivory XE 4027 black 9916 are not subject to "selec-tive treatment" according the Directive 2002/96/EC on Waste Electrical and Elec-tronic Equipment. ISO polymer designation: PA 10T/X ASTM designation: PPA, polyphthalamide The main distinguishing features of Grivory HT-PPA, when compared to other poly-amides, are its good performance at high temperatures providing parts which are stiffer, stronger, have better heat distortion and dimensional stability as well as excel-lent chemical resistance and low moisture absorption. Grivory XE 4027 black 9916 is especially suitable for injection moulded components in electrical and electronic applications which require a flame class acc. UL 94 V-0. The material is suitable for lead-free SMT reflow soldering acc. i.e. JEDEC J-STD-020C (peak temperature 260°C). Compo-nents conforming to JEDEC MSL1 are achievable.

锂电材料物性对比

电池材料厂家技术标准积累 深圳市贝特瑞 MSG-S(518) 负极石墨粒径：D10=9.764；D50=17.136um；D90=28.189；水分:0.039;碳含量:99.952;TAP密度;1.036 比表面 积:2.784；首次容量/效率:363.51/94.18 深圳市贝特瑞 518 负极石墨粒径：D10=9.862；D50=16.888um； D90=28.374；水分:0.04%; 碳含量:99.962; TAP密度;1.042% 比表面积:2.625；首次容量/效率:352.3/92.5% 深圳市贝特瑞 AG 负极石墨粒径：D10=7.137；D50=18.058um； D90=37.495；水分：0.035;碳含量：99.676;TAP密度：1.001 首次容量/效率:320.83/90.42% 深圳市贝特瑞 AG 负极石墨粒径：D10=7.53；D50=17.779um； D90=39.648；水分：0.041;碳含量：99.743;TAP密度：1.002 ，首次容量/效率:326.51/90.67% 深圳市贝特瑞 SAG-23 负极石墨粒径：D10=8.318；D50=21.097um； D90=47.119；水分：0.04；碳含量：99.925；TAP密度：1.021 ，比表面积:4.605；首次容量/效率:332.11/92.08 深圳市贝特瑞 818 负极石墨粒径：D10=11.453；D50=18.226um； D90=28.762；水分：0.036；碳含量：99.964;TAP密度：1.121 比表面积:1.947;首次容量/效率:364.63/95.29% 深圳市贝特瑞 818 负极石墨粒径：D10=10.859；D50=18.033um；

材料物性表

EXTRUSION APPLICATION

Introduction Responsible for a long line of accomplishments in outstanding engineering plastics, UBE NYLON products have won the trust and respect of users the world over. UBE NYLON – NYLON 6, NYLON COPOLYMERS – is in wide use throughout industry with their unique properties utilized to their fullest potential. UBE NYLON 6 has a number of excellent properties as follows: Excellent in impact strength and rigidity Having a smaller friction coefficient, thus excellent in abrasion resistance Excellent in resistance to oils, solvents and chemicals Superior in heat resistance Appropriate to mass production, contributing to cost reduction Summary 1. Introduction 2. Nomenclature 3. Monofilament Applications 4. Film Applications 5. TERPALEX Polyamide 6/66/12 Copolymer Nomenclature The first 2 digits in the code indicate the type of Polyamide. The third and fourth digits indicate the molecular weight level for 1000 series. In case of copolymer, the third digit shows the viscosity level. The co-polymerization ratio can be roughly calculated from the fourth digit multiplying by 5. “T” means the basic grade for monofilament application and the grade contain some additives for maintain good process stability and high trans-parency. In case of “MT”, means monomer con-taining grade offering good flexibility and softness. 10: Polyamide 6 homopolymer 50: Polyamide 6/66 copolymer 70: Polyamide 6/12 copolymer Ex. 1022FDX04: : c.a. 22 x 1,000 = 22,000 Ex. 5034MTX1: : level = 3 (high viscosity) : c.a. 80/20(4 x 5 = 20et%) : monomer-contain type 2 Introduction

PvC硬度换算

PVC硬度对照表 注意:此表中的P数表示:100PHR的PVC粉,其中液体总量.液体总量包括增塑剂和环氧大豆油等. 不同增塑剂,有不同的增塑效率. 比DOP增塑效率大的有:DOA,DOTP等. 比DOP增塑效率小的有:DINCH,DINP,DIDP,TOTM,S-52聚酯(PN-1030,W-2050,)等.

硬度对比(GB2411标准)SHORE A和D A D 73 22 76 23 77 24 80 28 83 33 89 39-40 91 43-44 92 44 93 45-46 94 46 95 47-48 96 51 97 52-53 98 53-54 100 58-59 硬度的換算 硬度表示一般分为绝对硬度与相对硬度，绝对硬度一般只会在科家界使用，而在实际生产中极少应用，故通常我们所接触到的硬度单位体系为相对硬度，常有几种表示方法：肖氏硬度（又称：邵氏硬度）、洛氏硬度、布氏硬度（又称：勃氏硬度）、洛克氏硬度其换算关系详见下列公式：

1、肖氏硬度（HS）=布氏硬度（BHN）/10 + 12 2、肖氏硬度（HS）=洛氏硬度（HRC）+ 15 3、布氏硬度（BHN）=洛克氏硬度（HV） 因为肖氏硬度就是邵氏硬度，故无换算关系可言。 一般聚氨酯弹性体的硬度都采用美国邵氏公司(Shore)的A, B, C, D, DO, E, M 等硬度表测试。传统上滑板轮都比较软故都用A表，因此滑手比较熟悉A表。但近年滑板轮硬度逐渐提高，超过了95A，A表因为在超过95A的硬度时测试失准，故而近年来有些公司采用比较适合硬度更高的D表测试。但D表也有缺陷，因为D表测试头是针式，故而常刺穿轮子表面，使测试值不准。因此也有的公司采用B表测试然后换算成A 表的，如SkateOne。这样做目的是因为大多数滑手比较熟悉A表，因此方便滑手比较。B表得值+20就是A 表值。而D表和A标的关系.由上可以看出，D50可能相当于A97左右。A与D仅仅是测量方法不一样和质量是没有任何关系的。 注意:硬度读数,不同的国家时间(秒)是不一样的:日本是3秒,中国是15秒,还有5秒和10秒读数的.不同时间的读数会有一点差异;读数时间短,硬度大.但一般相差1-2 Shore A

物性表

Safety Data Sheet complies with:directive 91/155/EEC revision:2.0 ISO 11014-1:Safety data sheet for chemical products. revision date:02/02/1998date of issue: 26/02/1998 p 1. Product and company identification Product name:Stanyl ?Product code:TE250F3 Manufacturer: DSM Engineering Plastics P.O. Box 43,6130 AA Sittard The Netherlands Emergency number: The Netherlands +31 (0)46 4 76 55 55 2. Composition/Information on ingredients This chemical product is a preparation Chemical nature:(poly)amide PA 46CAS number:50327-22-5Components contributing to the hazard: The material contains Sb 2O 3 as a synergist with an average content of max. 7%. Sb 2O 3 is classified as a harmful (Xn) substance with a risk phrase R40 carcinogen class 3. However, the Sb 2O 3 is embedded in an impervious matrix of polymer and is therefore less biological available than the free Sb 2O 3 (see also Section 15). 3. Hazards identification Most important hazards:Hazard warning not required Specific hazards: Vapour and fumes released at elevated processing temperatures may be irritant for the eyes, the nose, the throat and the respiratory tract and in case of overexposure may cause nausea and headache. The material is not classified as being a dangerous preparation according to the EEC-Directive 88/379 and the subsequent amendments. See also Section 15.4. First-Aid measures Inhalation: When fumes of molten material have been inhaled;- Move person to fresh air as quickly as possible - rest in half upright position - loosen clothing - keep warm In case of respiratory problems move person to first aid station for medical treatment.Skin contact: Any molten material on the skin/burns should be cooled (off) as quickly as possible by means of cold water.Cover the wound with sterile cloth and move person to first aid station or hospital for medical treatment.Attention: never pull off the molten material from the wound.Eye contact: Any material entering the eye should be flushed out with copious volumes of water.Ingestion: No danger of toxicity, this material is biologically inactive (see also Section 11). 5. Fire-fighting measures Extinguishing media: Water, water/foam, CO 2, ABC fire extinguisher powder.Specific Hazards: Treat the material as a solid that can burn. Moulded parts or solid granules generally burn slowly with flaming drips.

常用材料的热物性参数

表1 各种金属的热物性值 温度 C 比热 cal/(g·C) 导热系数 cal/(cm·s· C) 密度(g/cm3)液相 线、固相线温度 (C) =7.88(20C) =7.3(1500C) =7.0(1600C) =7.86(15C) =7.86(15C) =7.85(15C) =7.85(15C) =7.83(15C)

续表1 各种金属的热物性值 温度 C 比热 cal/(g·C) 导热系数 cal/(cm·s· C) 密度(g/cm3)液相 线、固相线温度 (C) =7.73(15C) Ts=1488 T L=1497 =7.84(15C) T S=1420 T L=1520 =7.7(15C) 13.1Cr,0.5Ni T S=1399 T L=1454 =7.0(15C) 比热相对于 普通铸铁

=7.1(15C) 温度 C 比热 cal/(g·C) 导热系数 cal/(cm·s· C) 密度(g/cm3)液相 线、固相线温度 (C) =7.5~7.8(15C) =8.92 T S=T L=1083

s=2.70(15C) T S=T M=660.2 温度 C 比热 cal/(g·C) 导热系数 cal/(cm·s· C) 密度(g/cm3)液相 线、固相线温度 (C) s=1.74 T L=T S=651 s=6.09 T S=1395 T L=1427

表2 铸型的热物性计算公式

硅砂，干型，呋喃铸型600C以下 0.385<<0.494 0.0058

材料物性表

Product Data Sheet CHARACTERISTICS TEST METHOD Physical Properties Specific Gravity ASTM D792 1.20 1.20 Mould Shrinkage ASTM D9550.1-0.3%0.001-0.003in/in Mechanical Properties Tensile Strength ASTM D63890MPa 13050psi Flexural Strength ASTM D790125MPa 18125psi Flexural Modulus ASTM D7906500MPa 943ksi Notched Izod Impact Strength (3.2mm) ASTM D256 85 J/m 1.6 ft-lb/in Thermal Properties Heat Deflection Temperature @ 1.82MPa (264 psi) ASTM D648145°C 293°F Electrical Properties Surface Resistivity ASTM D2571E15ohms 1E15ohms Description: Glass Fiber Reinforced Polypropylene PPR 40G NC702 Product Code: 5218702Internal Code: NATURAL Colour: Maxxam TM NOMINAL VALUE (SI)NOMINAL VALUE (ENGLISH)Flammability Properties Flame Rating @ 0.8mm Internal HB HB Processing Conditions PP Barrel Temperature 200-240 °C 392-464°F Mould Temperature 30-60 °C 86-140°F Drying Temperature 80-85 °C 176-185°F Drying Time 2-3 Hour 2-3 Hour Injection Pressure Hold Pressure Screw Speed Back Pressure Rev #: 0, Revision Date: 6/8/2010 PRINTED IN SHENZHEN LHM 33587 Walker Road,Avon Lake,Ohio 44012, USA, Tel 1-440-930 1000 WHEN YOU HAVE QUESTION WITH ENGINEERING PLASTICS, WE COMPOUND THE ANSWER. No.1, Qihang Industrial Park,Haoxiang Road, Shajing Town, Baoan,Shenzhen, P.R.China,Tel:86-755-29692888MODERATE MED-HIGH MED-HIGH THIS IS NOT A PRODUCT SPECIFICATION LOW THE INFORMATION PRESENTED HEREIN IS PRESENTED IN GOOD FAITH AND TO THE BEST OF OUR KNOWLEDGE IS TRUE AND ACCURATE. IT IS INTENDED AS A GUIDE AND IS OFFERED FOR USE AT YOUR DISCRETION AND RISK. POLYONE DOES NOT GUARANTEE RESULT AND DISCLAIM ANY LIABILITY INCURRED IN CONNECTION WITH THE USE OF THE PRODUCTS DESCRIBED OR THE INFORMATION PRESENTED Tel: 86-755-29692888

物性表

DuPont ? Zytel ? nylon resin Zytel ? 101L NC010 Value DAM 50%RH Identification Resin Identification ISO 1043PA66 Part Marking Code ISO 11469>PA66< Mechanical Yield Stress ISO 527MPa (kpsi) 82 (11.9)55 (8.0) Strain at Break ISO 527% 50mm/min 45 Nominal Strain at Break ISO 527%25>100 Yield Strain ISO 527% 4.525 Tensile Modulus ISO 527MPa (kpsi)3100 (450) 1400 (200) Tensile Creep Modulus ISO 899 MPa (kpsi) 1h 1400 (200) 1000h 820 (119) Poisson's Ratio 0.41 Flexural Modulus ISO 178MPa (kpsi)2800 (410) 1200 (174) Notched Charpy Impact Strength ISO 179/1eA kJ/m 2 -30°C (-22°F) 4.53 23°C (73°F) 5.515 Unnotched Charpy Impact Strength ISO 179/1eU kJ/m 2 -30°C (-22°F)400NB 23°C (73°F) NB NB Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm. Test temperatures are 23°C unless otherwise stated. The DuPont Oval Logo, DuPont?, The miracles of science? and Zytel? are trademarks or registered trademarks of DuPont Company. Copyright? 2005. 050630/050630 The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated; these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise. The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this publication is to be considered as a license to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. Caution: Do not use this product in medical applications involving permanent implantation in the human body. For other medical applications see "DuPont Medical Caution Statement", H-50102. https://www.360docs.net/doc/fe6518831.html, Zytel ? 101L NC010 is a lubricated polyamide 66 resin for injection molding. Property Test Method Units

PVC胶料硬度对照表精选文档

P V C胶料硬度对照表精 选文档 TTMS system office room 【TTMS16H-TTMS2A-TTMS8Q8-

PVC胶料硬度对照表常用硬度对照表

说明：1）P数行业通俗叫法，也是判断胶粒硬度的一种指标，邵氏A值是国际标准。不同厂家其P数所对应的邵氏A值会略有差别。

2）在秋冬季时，上述硬度A值实测时要提高到±1~2A。每年自11月1日至次年4月30日，所有配方生产使用时增加可塑剂用量2KG。 3）本对照表只作参考，不作质保承诺，如与此冲突处，请提变更申请。本部将斟情调整。 4) 硬度测试片厚5mm±，硬度计探针在1KG力下压下，15S后读数。 PVC硬度对照表 帕氏硬度厚度邵氏硬度测试值平均硬度值 30P 6mm 93-96 ° ° 35P 6mm 87-93 ° 90 ° 38P 6mm 89-90 ° ° 40P 6mm 88-90 ° 89 ° 45P 6mm 84-90 ° 85 ° 50P 6mm 82-83 ° ° 55P 6mm 70-80 ° 79 °

60P 6mm 74-76 ° 75 ° 65P 6mm 73-75 ° 74 ° 70P 6mm 72-74 ° 73 ° 75P 6mm ° 70 ° 80P 6mm 67-68 ° ° 85P 6mm 64-66 ° 65 ° 90P 6mm 63-64 ° ° 95P 6mm 58-60 ° 59 ° 100P 6mm 57-59 ° 58 ° 110P 6mm 54-56 ° 55 ° 测试温度:23度的测试板材:65*45*6MM

各种塑料基本物性表

塑膠原材料物性表 材料名稱密度收縮率成本USD/kg燃燒狀態料管溫度射出壓力 (Kg/cm2)模溫 (C°)用途ABS (BK) 1.42~2.4 ABS (HB COLOR) 1.05 1.42~1.75/450 ABS (HB GF10) 1.2 1.75~3.72/about 500 ABS (HB GF20) 1.220.002 2.19/60-80 ABS (HB GF30) 2.25~4.26/ ABS (Natural) 1.25~2.4/ ABS (PA/757BK) 1.53~1.75/ ABS (PA/765AB) 2.2/ ABS (V0 GF10) 1.2 3.86/about 500 ABS (V0) 1.05 1.42~2.11 ABS (透明) 1.96~2.06 ABS (Acrylonitrile Butadiene Styrene)丙烯睛-丁二烯-苯乙烯1.05~1.1 0.005 1.25~2.4 易燃, 暗黃,有黑煙. 軟 化.特有氣味. 硬, 脆. 金 屬聲 180~260450~210050~80 電器,日用品外殼,玩具,家具,運動用品,燈 飾,汽車配件 AS (GF20) 1.260.002210-28060-80 AS=SAN(Styrene-Acrylonitrile Copolymer)丙烯睛-苯乙烯1.06 0.004/190~280 700~2300 40~80 食具,日用品,透明裝飾面,主表面 EPS 發泡膠 Expanded PolyStyrene貨品包裝,絕緣板, 裝飾品 EVA 乙烯-醋酸乙烯共聚物. Ethlene-Vinyl Acetate Copolymer橡皮膠120~25030~50鞋底,吹氣玩具製品,包裝膠膜 HIPS (BW-4(H45))/ HIPS (HB) 高衝擊聚苯乙烯 High Impact PS/ 1.1~1.3/ HIPS (PA-765BK) 2.2耐沖擊.玩具,日用品,收音機殼,電視機殼. HIPS (V0)/ 1.55 PA +GF30 (V0)260~29050~90 PA 66 (HB)/250~31050~90噪音小,軟. 牙刷,線圈架, 拉絲,束帶,齒輪,電動玩具外殼,電器配件,運動用品 PC(GE10G15) 5.508/ PC(GF40) 1.820.15%270-31080-120 PC(HB) 3.63 PC(L-1250YN) 1.2 3.7/ PC(N) 聚碳酸脂. 防彈膠 Polycarbonate 1.2 0.60% 4.2~4.75 稍難燃, 黃色焰,黑煙. 軟化. 特有味 260~300 (330劣化) 700~2100 85~120 咖啡壺,電動工具外殼,安全頭盔,透明片, 防硬玻璃,電器零件 PC(透明) 4.0~4.2 PC+ABS 2.32~2.98 PC+ABS (FR2000, V0) 4.485215~240about 75060~80 PC+ABS (KU2-1468,V0)240~280about 75060~90 材料名稱密度收縮率成本USD/kg燃燒狀態料管溫度射出壓力 (Kg/cm2)模溫 (C°)用途 PE 聚乙烯1.14 0.45% 易燃, 尖端黃,下端藍. 邊滴邊燃. 石腊燃燒味170-25040-60 PE (Polyethlene)0.95 3.50%150-23020-40包裝膠袋,膠瓶,水桶,電線,大貨桶,玩具PE(High Density PE) 高密160~310700~140025~70包裝膠袋,膠瓶,膠花,電線,大貨桶,玩具PE(Low Density PE) 低密150~310600~140025~70包裝膠袋,膠瓶,水桶,電線,大貨桶

POM FG2025物性表

名称规格：POM FG2025 产地：韩国工程料 特性： 提供方：东莞东扬塑胶T E L：1 3 6 /8 6 6 5/6 6 6 1 ①原料描述部分 规格级别：--- 外观颜色：--- 用途概述：--- 备注说明：特性：玻纤填充Glass Fiber ②原料技术数据 性能项目试验条件[状态] 测试方法测试数据数据单位基本性能 吸水率23℃，60%RH ASTM D-570 0.20 % 熔体流动速率--- ASTM D-1238 9 g/10min 物理性能 填充材料含有率--- --- 25 % 比重--- ASTM D-792 1.59 --- 机械性能拉伸强度23℃ASTM D-638 1450 kgf/cm2 伸缩率23℃ASTM D-638 3 % 弯曲强度23℃ASTM D-790 2100 kgf/cm2 曲折弹性率23℃ASTM D-790 8.80 ×104kgf/cm2断裂强度2mmt ASTM D-732 760 kgf/cm2 IZOD冲击强度Notch 3.2mmt ASTM D-256 10 kgf.cm/cm 拉伸冲击强度 3.2mmt Stype ASTM D-1822 180 kgf.cm/cm2洛氏硬度M scale ASTM D-785 M95 --- 电气性能表面电阻率--- ASTM D-257 1×1016Ω 体积电阻率--- ASTM D-257 1×1014Ω.cm 耐电压--- ASTM D-149 23 KV/mm 加工性能成型收缩率3mmt,直径100mm --- 0.5 % 热性能 燃烧性0.8mmt UL 94 HB --- 熔点10℃/min DSC Method 165 oC

PVC胶料硬度对照表

PVC胶料硬度对照表常用硬度对照表 P数（P%）邵氏硬度 （A） 合格范围 25P 98 A ±2A 70P 75A ±3A 30P 97 A ±2A 75P 70 A ±3A 35P 95 A ±2A 80P 68 A ±3A 40P 92 A ±2A 85P 65 A ±3A 45P 90 A ±2A 90P 63 A ±4A 50P 88 A ±3A 95P 60 A ±4A 55P 84 A ±3A 100P 58 A ±4A 60P 80 A ±3A 110P 55 A ±4A 65P 77 A ±3A 说明：1）P数行业通俗叫法，也是判断胶粒硬度的一种指标，邵氏A值是国际标准。不同厂家其P数所对应的邵氏A值会略有差别。 2）在秋冬季时，上述硬度A值实测时要提高到±1~2A。每年自11月1日至次年4月30日，所有配方生产使用时增加可塑剂用量2KG。 3）本对照表只作参考，不作质保承诺，如与此冲突处，请提变更申请。本部将斟情调整。 4) 硬度测试片厚5mm±0.5，硬度计探针在1KG力下压下，15S后读数。

PVC硬度对照表 帕氏硬度厚度邵氏硬度测试值平均硬度值30P 6mm 93-96 ° 94.5 ° 35P 6mm 87-93 ° 90 ° 38P 6mm 89-90 ° 89.5 ° 40P 6mm 88-90 ° 89 ° 45P 6mm 84-90 ° 85 ° 50P 6mm 82-83 ° 82.5 ° 55P 6mm 70-80 ° 79 ° 60P 6mm 74-76 ° 75 ° 65P 6mm 73-75 ° 74 ° 70P 6mm 72-74 ° 73 ° 75P 6mm 70-70.5 ° 70 ° 80P 6mm 67-68 ° 67.5 ° 85P 6mm 64-66 ° 65 ° 90P 6mm 63-64 ° 63.5 ° 95P 6mm 58-60 ° 59 ° 100P 6mm 57-59 ° 58 ° 110P 6mm 54-56 ° 55 ° 测试温度:23度的测试板材:65*45*6MM

常用材料物性表

常用材料物性表 清洗要求 压力速度 ABS 210℃-245℃90℃≥2H 25℃-75℃中高压中高速高温下材料会分解，正常温度下半小时后需清洗螺杆。 压中速正常温度下材料也会分解，停机十分钟需排料。 ABS+玻纤220℃-250℃90℃≥3H 50℃-80℃中高压中高速正常温度下材料也会分解，停机十分钟需排料。 ABS+AS 220℃-240℃90℃≥3H 60℃-85℃中高压中高速高温下材料会分解，正常温度下半小时后需清洗螺杆。 ABS+PC 240℃-280℃110℃≥4H 50℃-100℃中高压高速长期高温下材料会分解，正常温度下半小时后需排料。 PA6 240℃-270℃105℃≥8H 80℃-90℃中高压高速高温下材料会分解，正常温度下半小时后需清洗螺杆。 PA6+玻纤250℃-280℃110℃≥8H 80℃-90℃中高压高速高温下材料会分解，正常温度下半小时后需清洗螺杆。 PA12 240℃-290℃85℃≥5H 30℃-40℃中压高速高温下材料会分解，正常温度下半小时后需清洗螺杆。 PA12+玻纤240℃-270℃85℃≥5H 80℃-90℃中压高速高温下材料会分解，正常温度下半小时后需清洗螺杆。

压高速高温下材料会分解，正常温度下半小时后需清洗螺杆。 PA66+玻纤260℃-280℃105℃≥12H 70℃-90℃中压高速高温下材料会分解，正常温度下半小时后需清洗螺杆。 PBT 240℃-270℃140℃≥4H 25℃-50℃中压高速长期高温下材料会分解，正常温度下半小时后需排料。 PBT+玻纤240℃-265℃140℃≥4H 25℃-50℃中压高速长期高温下材料会分解，正常温度下半小时后需排料。 PC 260℃-300℃120℃≥4H 70℃-120℃高压高速、低速无需清洗，320℃高温下不会分解，如出现变色需排料。 PC+玻纤250℃-290℃125℃≥4H 70℃-120℃高压高速无需清洗，280℃高温下不易分解，如出现变色需排料。 PC+PBT 235℃-285℃130℃≥4H 35℃-95℃中高压高速长期高温下材料会分解，正常温度下半小时后需排料。 PE-HD 200℃-230℃/ / 50℃-95℃低压高速无需清洗，高温下不会分解，长期高温下流动性会增加。 PE-LD 180℃-220℃/ / 20℃-40℃中高压高速无需清洗，高温下不会分解，长期高温下流动性会增加。 PEI 340℃-400℃150℃≥4H 100℃-175℃中高压高速无需清洗，高温下不易分解，正常温度下半小时后需排料。 PEI+玻纤340℃-420℃150℃≥4H 100℃-175℃中高压高速无需清洗，高温下不易分解，正常温度下半小时后需排料。