伊莎贝拉2012年秋冬季开发制作进度量化
dbl5809
September 2006Mercedes-BenzSupply Specification Knitted fabricsDBL 5809BQF availableAdditional DaimlerChrysler Standards required:DBL 5306, DBL 5307, DBL 5450, DBL 5805, DBL 8585, MB Special Terms .Supersedes edition: 09.2005 Refer to Section Changes: Page 6Fortsetzung Seite 2 bis 45Issued by:DaimlerChrysler AG70546 Stuttgart Standards (EP/QIN) Technical responsibility (name): WeißDepartment: PWT/VWK Plant: 050Telephone: +49/(0)7031-90-87656 HPC: F105 Technical coordination by PWT Plant 059, Department PWT/VWK Name: Dr. Schuh Phone +49/(0)7031-90–44270HPC: 059 X 685 Confidential! All rights reserved. Distribution or duplication in part or in whole without prior written approval of DaimlerChrysler AG is not permitted.In case of doubt, the German language original should be consulted as the authoritative text.1. APPLICATIONS Refer to Table 1, pages 1 to 4.2. MATERIALS Refer to Table 1, pages 1 to 4.Table 1Product versions Designation Materials% by weightApplication examples .00 *High-pile circular knitgoods Pile: polyacrylonitrile / Knitted ground fabric: polyester/ Back bonding withacrylate dispersionInterior trim in commercial vehicles .01* Circular-knitted cut-plush fabric Pile: PolyesterKnitted ground fabric: polyester.02* Circular-knitted cut-plush fabric with foam lamination Pile: polyester / Knitted ground fabric:polyester / Foam: ether polyurethane / Film: ether polyurethane; 0,03 mm thick.03* Knitted velour Pile : polyester texturedKnitted fabric : polyester texturedOff-road vehicles - dome lining .04* Pile knitted fabric: according to PV 03 /Foam: ether polyurethane / Reverse side: knitted polyester fabric- sliding roof panel.05* Pile knitted fabric: according to PV 03 /Foam: ether polyurethane / Film:polyurethane (0,05 mm) / Reverse side: knitted polyester fabric- sliding roof panel (with low air permeability).06 Circular-knitted fabricKnitted fabric: polyesterInterior trim cover - off-road vehicles - vans- multi-purpose vehicle .07 Circular-knitted velour Pile: PolyesterBacking: PolyesterInterior trim cover for commercial vehicles.08 Circular-knitted fabric Knitted fabric according to PV 06Reverse side DBL 5805.32Sliding roof panel for off-road vehicles.09 Knitted fabric with flat appearance, heavyKnitted fabric: polyesterParcel shelf cover W 203 model refinement package .10* Knitted carpet Pile: 80 ± 3 polyester; 20 ± 3 polyamideKnitted ground fabric: polyester Coating: moldable synthetic latexCarpet covering in commercial vehicles .11 Knitted fabric with flat appearanceKnitted fabric: polyesterInterior paneling cover for C 219.12 Decorative knitted fabricKnitted fabric: polyesterDome lining/Pillar cover W 169.13 Knitted fabric: polyesterwith stain release finishCover for paneling SKN/C 14. Circular-knitted fabricKnitted fabric: polyesterPillar cover W 168 model refinement package .15 ** Circular-knitted velour Knitted fabric: polyesterFoam: ester polyurethane (DBL 5450.20)Multi-purpose vehicle dome lining* Not for new designsFor technical data, if required, refer to DBL 5809, edition January 2003. ** not for new designsPage 2DBL 5809 : September 2006Table 1 (continued)Product versions Designation Materials % by weight Application examples .16 Flat-knitted fabrics Knitted fabric: polyester Door paneling cover W 168model refinement package.17 Circular-knitted fabric Knitted fabric: polyester Loudspeaker cover under maincover W 168.18 Circular-knitted fabric Knitted fabric: polyester Dome lining W 168 .19 Circular-knitted velour Knitted fabric: pile + ground: polyesterFoam: ether polyurethane basis (DBL 5450 AA 10)Nonwoven: polyester (DBL 5805.30)Door paneling cover W 168.20 Circular-knitted velour Pile: Polyester Knitted ground fabric: polyesterPassenger cars (type 140) - parcel shelf cover.21 Knitted fabric according to PV 20; reverse DBL 5805.32- sliding roof panel.22 ** Knitted fabric according to PV 20; Foam: ester polyurethane (DBL 5450.20); reverse: polyurethane film (0,05 mm)- e.g. cover C pillar.23 Knitted fabric PV 20; reverse: kiss rolled with acrylate foam- small parts cover.24 ** Flat-knitted fabrics with woven fabric appearance Knitted fabric: PV 32;foam: ester-polyurethane (DBL 5450.20); reverse: polyurethane film (0,04mm)Passenger cars (type W 211)- seat back lining cover .25 Circular-knitted velour, light Pile: Polyester Backing: Polyester Passenger cars (type 202) - parcel shelf cover- pillar cover.26 Circular-knitted fabrics, flat appearance Knitted fabric: polyester (stain release finish according to drawing, if required) Passenger cars (type C 209) - cover: parcel shelf, doorpockets, headlining, sliding roof,pillars.27 Circular-knitted fabrics, flat appearance with brushed effect Knitted fabric: polyester (stain release finish according to drawing, if required) Passenger cars (type W 211) - cover: parcel shelf, doorpockets, headlining, sliding roof, pillars, sun visors.28 Circular-knitted velour, brushed; heavy Pile: polyester (textured) Backing: Polyester with stain release finish for components prone to staining Passenger cars (type 210/C208) - parcel shelf cover- trim for instrument panel lowerparts / - door pocket cover- pillar cover.29 Circular-knitted velour, brushed; light Pile: polyester (textured) Backing: Polyesterwith stain release finish- dome lining.30 Flat-knitted fabrics Knitted fabric: polyester Passenger cars- rear speaker cover** Not for new designsPage 3DBL 5809 : September 2006Table 1 (continued)Product versions Designation Materials % by weight Application examples .31 Knitted extremely fine velour Pile: Polyester Backing: Polyester Passenger cars- cover for moldings.32 Flat-knitted fabrics with woven fabric appearance Knitted fabric: polyester Passenger cars- decorative product for seat backlinings.33 Circular-knitted velour Pile: polyester (textured) Backing: Polyester 220 / C 215 / model refinement package W 210- e.g. for parcel shelf.34 Knitted fabric PV 33; with stain release finish - for components prone to staining(e.g. door pocket, sun visor).35 Flat-knitted fabrics Knitted fabric: polyester W 202 for door paneling cover .36 ** Circular-knitted velour Knitted fabric PV 34 Foam: ester polyurethane (DBL 5450.20) Reverse: polyurethane filmW 220- mirror cover - map pocket .37 Circular-knitted velour Knitted fabric: polyester (stain release finish acc. to drawing) W 203Dome lining, pillar cover etc..38 Knitted fabric with flat appearanceKnitted fabric: polyester CL 203 A, B, C pillar covers.39 ** Circular-knitted velour Knitted fabric PV 33 Foam: ester polyurethane (DBL 5450.20)W 220- A, B, C pillar covers .40 ** Knitted fabric PV 34 Foam: ester polyurethane (DBL 5450.20)Reverse: fleece fabric (DBL 5805.30)W 220- Door pocket .41 ** Knitted fabric PV 34 Foam: ester polyurethane (DBL 5450.20)Charmeuse: polyester (courses 140± 20, wales 90± 10)W 220- Sliding roof, sunroof .42 ** Knitted fabric with flat appearance Knitted fabric: polyester Foam: ester polyurethane (DBL 5450.20)W 168- Head restraint cover.43 Knitted fabric, laminated Knitted fabric: polyester Foam: ether polyurethane (DBL 5450 PV 10)Charmeuse: polyester (44 dtex matt)- Seat covers.44 Flat-knitted fabrics with woven fabric appearance Knitted fabric: PV 32 Foam: ether polyurethane (DBL 5450 PV 10)Charmeuse: polyester (courses 140± 20, wales 90± 10)Passenger cars- Ruffled pocket.45 Decorative knitted fabric Knitted fabric: polyester W 221 - Cover for rear shelf- Cover for sun visor.46 Knitted fabric PV 45 Foam: ether polyurethane (DBL 5450 PV 10)W 221 - Cover for pillars.47 Knitted fabric PV 45; with stain release finish.48 Knitted fabric PV 47 Foam: ether polyurethane (DBL 5450 PV 10)W 221- Dome lining .49 Knitted fabrics PV 45 Foam: ether polyurethane (DBL 5450 PV 10)W 221- Cover for wheelhouse liner ** Not for new designsPage 4DBL 5809 : September 2006Table 1 (continued)Product versions Designation Materials % by weight Application examples .50 Flat-knitted fabrics, light Knitted fabric: 87 ± 2 polyesterChild's seat cover.51 Knitted fabric, heavy 13 ± 2 elastomer Cover for seat cushion lengthadjustment.60 Circular-knitted velour (e.g. design Vassili) Knitted fabric: pile/ground polyester acrylate coating for SKN/C- Door lining.61 foam-laminated 14mm Knitted fabric: pile/ground polyesterFoam: ether polyurethane (DBL 5450 PV 10)Charmeuse: Polyester (courses 120 ± 20, wales 110 ± 10)- Seat upholstery cover.64 PV 65 fleece-laminated Knitted fabric according to PV 65Nonwoven: according to DBL 5805.37For multi-purpose vehicles .65 Circular-knitted velour (e.g. design Pyramid, Memphis, Uni)Pile: Polyester Backing: Polyester - upholstery cover seats.66 PV 65 fleece-laminated, heavy Knitted fabric according to PV 65 Nonwoven: according to DBL 5805.36- upholstery cover, middle seatpanel.67 PV 65 fleece-laminated, light Knitted fabric according to PV 65 Nonwoven: according to DBL 5805.38 - upholstery cover, all floors, onlycushion sides, folding seatbackrest.68 Circular-knitted velour (e.g. design Cassito, Vassili, Capella) Foam-laminated, 4mm Knitted fabric: pile/groundpolyesterFoam: ether polyurethanefor SKN/C- Seat upholstery cover .69 foam-laminated 2 mm (DBL 5450 PV 10) Charmeuse: Polyester (courses 120 ± 20, wales 110 ± 10).70 Self-adhesive circular-knitted fabrics Knitted fabric: polyester Adhesive: acrylate adhesiveControl valve cover C 208.71 Microvelour Knitted fabric: 94 polyester / 6 Elastan Adhesive: polyurethane Flock: polyamideStorage compartment cover rearseat W 240 .72 Microvelour self-adhesive Upper material: acc. to PV 71 Laminating adhesive: copolyesterNonwoven: polyester Adhesive: acrylate based.80 Knitted fabric Knitted fabric: 100 polyester Cover door center part W 169** Not for new designsAbbreviated designation : e.g. Textile, Knitted fabric DBL 5809.06Page 5DBL 5809 : September 2006 3. PROPERTIES3.1 - General requirementsThe knitted fabrics shall be free of production defects of any type which would impair the processing and utilization properties or the appearance. The construction and the reverse bonding of the pile in the backing shall show good durability in accordance with the intended application. In case of product versions 00, 20 to 25 and PV 36, the top of the pile surface shall be completely closed and shall not have any detrimental gaps or stripes. Problem-free adhesion properties of the backs with the adhesives used by us is required.- The visible knitted fabric distortion over the whole width shall not be more than 2 %. The knitted fabric shall not change its Parallel or Normal dimensions during storage or further processing by more than 2% (e.g. no excessive wind-up tension).- It shall be possible to clean the knitted fabrics efficiently using the foam cleaning process with cleaning agents on a neutral soap basis without change of color (or using the dry foam process). They shall also be adequately resistant to the effects of organic solvents, in particular of MB stain removers. (at least grade 4 DIN/EN/ISO 105-X12).- The self-adhesive product version PV 70, PV 72 shall be protected with a paper on the adhesive side.The paper shall be easy to peel off and have good interlaminar strength. An aging-resistant bond isrequired between knitted fabric/nonwoven and adhesive with good interlaminar strength.- The availability of a certificate of testing in accordance with the following method is specified as an overriding requirement for adherence to the emission values for interior trim materials: VDA 278;threshold values DBL 8585.The user is responsible for checking whether the version in his possession is the latest version. Forinquires on threshold values, please apply to VDA278.DC-Info@.In particular in the case of substances listed in DBL 8585 Section 2.3, the supplier is required tocontinuously minimize the concentration and emission at least in accordance with the state of the art, even when values have fallen below the required DBL threshold values.3.2 Shade and designIn accordance with approved sample and/or order.3.3 WidthIn accordance with order (unless otherwise specified - width tolerance + 15/- 2 mm).4. TECHNICALDATARefer to Table 2, pages 7 to 45.5. TESTMETHODSDIN/EN/ISO (refer to Table 2) or DBL 5306, Part II and DBL 5307.5.1 More precise indication of color fastness to light (hot light fastness) and aging (hot light aging) toartificial light at high temperatures in accordance with DIN / EN / ISO 105-B06Exposure conditions: 3 (normal); irradiance 1,2 W/m² (420nm)For type of apparatus C, filter system BS/SL shall be used.Color fastness (HLF)- Determination of end point: Exposure to ∆E 4,3+/-0,4 of reference 6(exposed/to covered). Color measurement of reference with whitereference tile as substrate.- Assessment: Comparison exposed specimen with original specimen for light source D65.Assessment with blue scale (references).Determination of aging (HLA)- Determination of end point: as for HLF, but with several consecutive cycles.For each cycle, a new reference 6 must be used.- Assessment: Comparison exposed specimen with original specimen for light source D65.Assessment with gray scale in accordance with DIN EN 20105-A026.DUTIES OF THE SUPPLIERRefer to MercedesBenz Special Terms No. 13 and No. 16, Purchase Conditions for Production Materials and Spare Parts for Motor Vehicles.7. SAMPLESRefer to MercedesBenz Special Terms No. 13.8. DELIVERIESRefer to MercedesBenz Special Terms No. 13 and DBL 5306, Section 104.Page 6DBL 5809 : September 20069. MARKINGRefer to MercedesBenz Special Terms No. 4, No. 24, No. 27 and DBL 5306, Section 105.10. PACKAGING, FORM OF SUPPLY AND DELIVERY CONDITIONSRefer to Mercedes-Benz Special Terms No. 30.11. STORABILITYRefer to DBL 5306, Section 107.INSTRUCTIONS12. SPECIALRefer to DBL 5306, Section 108.13. COMPLAINTSRefer to MercedesBenz Special Terms No. 16 and Purchase Conditions for Production Materials and Spare Parts for Motor Vehicles.14. ENVIRONMENTAL PROTECTION REGULATIONS/INDUSTRIAL SAFETYRefer to MercedesBenz Special Terms No. 30, No. 36 and DBL 8585 Negative substance list for material selection.Changes:Emission values for fabrics without lamination and with laminated nonwoven respecified. mc/liPV 49 newly adopted. mc/hmPage 7DBL 5809 : September 2006 Table 2:4. Technical data Product version requirements Test method00 01 02 03 04For technical data, if required, refer to DBL 5809, edition January 2003.Page 8DBL 5809 : September 20064. Technical data Product version requirements Test method05 06 07 08 094.1 Mass per unit area g/m²4.1.1 Total4.1.2 Knitted surface fabric4.1.3 Nonwovenfleece4.1.4 Fibers bonded with adhesive S: 170 +/- 20---S: 160 +20/- 10---S: 305 +/- 30170 ± 20120 +15/-1015 ± 3S: 200 +/- 20---DIN/EN 121274.2 Apparent (bulk) density kg/m³For technicaldata, if required,refer to DBL5809, editionJanuary 2003.- - - -DIN/EN/ISO8454.3 Compressive strength of foamkPa - - - -DIN/EN/ISO33864.4 Total thickness mm 4.4.1 Knitted surface fabric 1,0 ± 0,2-1,5 ± 0,2-2,7 ± 0,31,0 ± 0,20,8 ± 0,1-DIN/EN/ISO 5084(25cm², 0,2kPa)4.5 StitchdensityMinimum 1/dm4.5.1 Wales 4.5.2 Courses 100 ± 10165 ± 15130 ± 10200 ± 10100 ± 10165 ± 15135 ± 10120 ± 10DIN 538834.6. Linear density Tt 167 dtex f 32±2 76 dtex f 24 x1 167 dtex f 32±2 100 dtex f 36 x1167 dtex f 30 x1DIN/EN/ISO 2060 4.7 TensilestrengthMinimum N4.7.1 lengthwise 4.7.2 crosswise 300200250250500350300350DIN/EN/ISO13934-1, 2 Npre-tensioningforce,4.8 Tensile strength - elongation %4.8.1 lengthwise 4.8.2 crosswise70 ± 10125 ± 20120 ± 20150 ± 2070 ± 1070 ± 10120 ± 30160 ± 30test rate 100mm/min;4.9 Elongation% 4.9.1 lengthwise4.9.1.1 at 25 N4.9.1.2 at 50 N4.9.1.3 at 100 N4.9.1.4 at 150 N4.9.2 crosswise 4.9.2.1 at 25 N4.9.2.2 at 50 N4.9.2.3 at 100 N4.9.2.4 at 150 N S: 15 +/- 425 ± 530 ± 8-S: 45 +/- 860 ± 1080 ± 15-S: 40 +/1050 +12/-1070 +/- 15-S: 44 +/- 1258 +/- 1375 +20/-15-S: 8 +/- 317 ± 430 ± 8-S: 9 +/- 317 ± 430 ± 8-S: 16 +10/- 526 +10/-542 +10/-5-S: 40 +10/-553 +10/-565 ± 10-gauge length 100mmPage 9DBL 5809 : September 2006 4. Technical data Product version requirements Test method(continued) 05 06 07 08 094.10 Tear propagation resistanceMinimum N4.10.1 lengthwise 4.10.2 crosswise 2525121025252010DIN/EN/ISO13937-24.11 Separationresistance MinimumNlengthwise and crosswise4.11.1 Knitted fabric/foam, knitted fabric/nonwoven fleece, foam/film - - 12 +12 /- 4 -DIN 533574.12 Color fastness to rubbingMinimum Rating4.12.1 drylightcolors darkcolors 4.12.2 wetlightcolors darkcolors 4 - 54 - 54 - 54 - 54 - 54 - 554 - 54 - 54DIN/EN/ISO 105-X124.13 Color fastness (HLF)Minimum blue scale Rating 7 7 7 7 DIN/EN/ISO 105-B064.14 Aging (HLA)Minimum gray scale Rating 3periods34 periods33 periods35 periods3 - 4For test methodsrefer to Section5.14.15 Combustion test S: Fulfillment of requirements in accordance with DBL 5307, PV 10; for use in busesin accordance with PV 20 DBL 5307.5.1 or 5.1 + 5.24.16 FoggingtestQuantity of condensablesubstanceMaximum mg - - - 0,5DIN 75 2014.17 Cleanability It shall be possible to clean the knitted fabrics efficiently using the foam cleaning processwith cleaning agents on a neutral soap basis without change of color (or using the dry foamprocess). They shall also be adequately resistant to the effects of organic solvents, inparticular of MB stain removers. (at least grade 4 DIN/EN/ISO 105-X12).4.18 Emissionanalysis4.18.1 VOC value µg/g (ppm) 4.18.2 FOG value µg/g (ppm)≤ 100≤ 350 target value250≤ 100≤ 350 target value250≤ 100≤ 350 target value250≤ 100≤ 350 target value250DBL 8585VDA 278Critical individual substances shall not exceed the limit/target values indicated in DBL8585, Section 2.3.4.19 OdortestMaximum Grade 3 3 3 3VDA 270 C 2Page 10DBL 5809 : September 20064. Technical data Product version requirements Test method10 11 12 13 144.1 Mass per unit areaTotal g/m2S: 205 +/-20 S: 120 +/-15 S: 200 +/-20 S: 150 +/-15DIN/EN 121274.2 ThicknessTotal mm 0,9 ± 0,1 0,7 ± 0,1 1,6 ± 0,2 0,8 ± 0,1 DIN/EN/ISO 5084 (25cm², 0,2kPa)4.3 StitchdensityMinimum 1/dm 4.3.1 Wales4.3.2 Courses For technicaldata, if required, refer to DBL 5809, edition January 2003.130 ± 10 170 ± 1090 ± 10130 ± 1090 ± 10150 ± 10100 ± 10240 ± 15DIN 538834.4 Linear density Tt 76 dtex f 24 x1100 dtex f 36 x2167 dtex f 32/1 167 dtex f 32 167 dtex f 32 DIN/EN/ISO20604.5 TensilestrengthMinimum N4.5.1 lengthwise 4.5.2 crosswise 250400350250350250200400DIN/EN/ISO13934-1, 2 Npre-tensioningforce,4.6 Tensile strength - elongation %4.6.1 lengthwise 4.6.2 crosswise 110 ± 20130 ± 2080 ± 20110 ± 20150 ± 20200 ± 20160 ± 20100 ± 20test rate 100mm/min;4.7 Elongation% 4.7.1 lengthwise4.7.1.1 at 25 N4.7.1.2 at 50 N4.7.1.3 at 100 N4.7.2 crosswise 4.7.2.1 at 25 N4.7.2.2 at 50 N4.7.2.3 at 100 N S: 30 +/- 540 +7/-560 ± 10S: 35 +/- 545 +7/-560 ± 10S: 25 +/- 535 ± 845 ± 10S: 45 +/- 1055 ± 1065 ± 10S: 55 +/- 670 ± 1085 ± 15S: 95 +/- 10115 ± 15140 ± 20S: 58 +/- 675 ± 10100 ± 15S: 25 +/- 430 ± 640 ± 8gauge length 100mm4.8 Tear propagation resistanceMinimum N4.8.1 lengthwise 4.8.2 crosswise 2515201525182518DIN/EN/ISO13937-24.9 Color fastness to rubbingMinimum Rating 4.9.1 drylightcolors darkcolors 4.9.2 wetlightcolors darkcolors54 - 54 - 544 - 54 - 54 - 54 - 54 - 54 - 5DIN/EN/ISO 105-X124. Technical data Product version requirements Test method(continued) 11 12 13 144.10 Color fastness (HLF)Minimum blue scale Rating 7 7 7 7 DIN/EN/ISO 105-B064.11 aging (HLA)Minimum gray scale Rating 5 periods3 - 44 periods34 periods34 periods3For test methodsrefer to Section5.14.12 Combustiontest S: Fulfillment of requirements in accordance with DBL 5307, PV 10 (in case of gluing overfull surface without any loose areas whatsoever to be tested as composite).DBL 5307.5.1 4.13 FoggingtestQuantity of condensablesubstanceMaximum mg 0,5 0,5 0,5 0,5DIN 75 2014.14 Cleanability It shall be possible to clean the knitted fabrics efficiently using the foam cleaning processwith cleaning agents on a neutral soap basis without change of color (or using the dry foamprocess). They shall also be adequately resistant to the effects of organic solvents, inparticular of MB stain removers. (at least grade 4 DIN/EN/ISO 105-X12).4.15 4.15Stainreleasefinish only PV 13 Drips of paraffin oil shall not be absorbed even after an exposure time of one hour, but remain without wetting. Drips of distilled water may and should be absorbed.4.16 Emissionanalysis4.16.1 VOC value µg/g (ppm) 4.16.2 FOG value µg/g (ppm)≤ 100≤ 350 target value250≤ 100≤ 350 target value250≤ 100≤ 350 target value250≤ 100≤ 350 target value250DBL 8585VDA 278Critical individual substances shall not exceed the limit/target values indicated in DBL8585, Section 2.3.4.17 OdortestMaximum Grade 3 3 3 3VDA 270 C 24. Technical data Product version requirements Test method15 16 17 18 194.1 Mass per unit area total g/m2 4.1.1 Knitted surface fabric4.1.2 Nonwovenfleece S: 210 +/- 25135 +/- 15-S: 220 +/-20--S: 120 +/- 15--S: 115 +/- 15--S: 720 +40/-20250 +/-20120 +/-12DIN/EN 121274.2 Apparent (bulk) density of thefoamkg/m33 5 ± 3- - -68 +3/-2DIN/EN/ISO 845SupplementaryrequirementsDBL 5450.20. Supplementary requirementsDBL 5450.10.4.3 Compressive strength of foamkPa 4,5 ± 0,9 - - -5,5 ± 0,5DIN/EN/ISO33864.4 Total thickness mm 4.4.1 Knitted surface fabric4.4.2 Foam4.4.3 Nonwovenfleece S: 3,2 +/- 0,31,5 ± 0,2--0,8 ± 0,1---0,8 ± 0,1---0,6 ± 0,1---6,8 ± 0,41,8 ± 0,13,85 ± 0,11,15 +/- 0,15DIN/EN/ISO5084(25cm², 0,2kPa)4.5 StitchdensityMinimum 1/dm4.5.1 Wales 4.5.2 Courses 130 ± 15150 ± 20120 ± 15170 ± 20100 ± 10110 ± 1590 ± 10210 ± 1590 ± 5150 ± 10DIN 538834.6 Linear density Tt4.6.1 Ground 4.6.2 Pile 76 dtex f 2476 dtex f 24110 dtex f 36 x12x 167 dtex f 48110 dtex f 30-167 dtex f 32-167 dtex f 30167 dtex f 48DIN/EN/ISO20604.7 TensilestrengthMinimum N4.7.1 lengthwise 4.7.2 crosswise 30020035035030090200250400400DIN/EN/ISO13934-1, 2 Npre-tensioningforce, test rate4.8 Tensile strength - elongation %4.8.1 lengthwise 4.8.2 crosswise 100 ± 20200 ± 30110 ± 20120 ± 20120 ± 25120 ± 25120 ± 2590 ± 2070 ± 20100 ± 20100 mm/min;gauge length 100mm4. Technical data Product version requirements Test method(continued) 15 16 17 18 194.9 Elongation%4.9.1 lengthwise4.9.1.1 at 25 N4.9.1.2 at 50 N4.9.1.3 at 100 N4.9.2 crosswise 4.9.2.1 at 25 N4.9.2.2 at 50 N4.9.2.3 at 100 NS: 25 +/- 835 ± 1050 ± 15S: 65 +/- 1095 ± 15130 ± 30S: 20 +/- 630 ± 845 ± 10S: 25 +/- 635 ± 845 ± 10S: 35 +/- 745 ± 10-S: 65 +/- 1085 ± 10-S: 50 +/- 670 ± 1085 ± 15S: 25 +/- 535 ± 840 ± 10S: 3,0 +/- 1,07,0 ± 1,518 ± 3,0S: 6,0 +/- 1,516,0 ± 3,036 ± 5,0DIN/EN/ISO13934-1, 2 Npre-tensioningforce, test rate100 mm/min;gauge length 100mm4.10 Tear propagation resistanceMinimum N4.10.1 lengthwise 4.10.2 crosswise 1818201081015154040DIN/EN/ISO13937-24.11 SeparationforceMinimum Nlengthwise and crosswise4.11.1 Knittedfabric/Foam nonondestructiveseparationpossible - - -nonondestructiveseparationpossibleDIN 533574.11.2 Foam/Nonwovenfleece - - - -structuralbreakor minimum204.12 Color fastness to rubbingMinimumGrade d ry and wet 4 - 5 4 - 5 4 - 5 4-5 4 - 5 DIN/EN/ISO 105-X124.13 Color fastness (HLF)Minimum blue scale Rating 7 7 -* 7 7 DIN/EN/ISO 105-B064.14 Aging (HLA)Minimum gray scale Rating 3 periods34 periods3 -*4 periods34 periods3For test methodsrefer to Section5.14.15 Combustiontest S: Fulfillment of requirements in accordance with DBL 5307, PV 10 (in case of gluing overfull surface without any loose areas whatsoever to be tested as composite).DBL 5307.5.1 4.16 Foggingtest4.16.1 Quantity of condensablesubstanceMaximummg 1,0 0,5 0,5 0,5 1,0DIN 75 201* only in case of use of loudspeaker cover under main cover W 1684. Technical data Product version requirements Test method(continued) 15 16 17 18 194.17 Cleanability It shall be possible to clean the knitted fabrics efficiently using the foam cleaning processwith cleaning agents on a neutral soap basis without change of color (or using the dry foamprocess). They shall also be adequately resistant to the effects of organic solvents, inparticular of MB stain removers. (at least grade 4 DIN/EN/ISO 105-X12).4.18 Emissionanalysis4.18.1 VOC value µg/g (ppm) 4.18.2 FOG value µg/g (ppm)Target value: ≤100Target value: ≤250≤ 100≤ 350 target value250≤ 100≤ 350 target value250≤ 100≤ 350 target value250Target value: ≤100Target value: ≤250DBL 8585VDA 278Critical individual substances shall not exceed the limit/target values indicated in DBL8585, Section 2.3.4.19 OdortestMaximum Grade 3 3 3 3 3VDA 270 C 2。
宜家海绵要求新版
软质聚氨酯海绵填充-物理性能和机械性能要求内容本技术规范阐述了宜家对聚氨酯海绵填充材料的物理性能、机械性能和结构性能的要求。
本规范适用于块状海绵。
关于本规范产品的使用品质在很大程度上以使用特定时间后的材料舒适度来评估。
本规范旨在确保软质聚氨酯海绵部件在使用期间可以保持其舒适性。
变更执行本技术规范（版本号AA-300587-4）中的变更，在宜家销售产品中最迟应在包装周数章1446（2014年46周）之前执行，除非另有说明。
宜家销售产品中使用的海绵应按照调整后的测试方法对疲劳造成的厚度损耗和疲劳造成的硬度损耗进行测试，该要求最迟应在包装周数章1618（2016年18周）执行。
按照本技术规范先前版本要求生产的已包装完毕的产品，包括产品部件和材料，应在符合本版本技术规范要求的产品出货前全部完成出货。
目录1 海绵的物理性能，机械性能和结构性能要求： (3)1.1测试方法和标准 (3)1.1.1硬度 (3)1.1.2压陷比 (3)1.1.3回弹率 (4)1.1.4由疲劳导致的厚度损耗 (4)1.1.5 由疲劳导致的硬度损耗 (4)1.1.6永久压缩变形率 (5)1.1.7恢复时间–只适用于慢回弹海绵 (5)1.1.8灰分含量 (5)1.1.9表观密度 (6)1.1.10拉伸强度 (6)1.1.11断裂伸长率 (6)1.2所有海绵的总体要求 (6)1.2.1硬度公差 (8)1.2.2灰分含量 (8)1.3特定类型海绵的具体要求 (9)1.3.1标准聚氨酯海绵 (9)1.3.2阻燃型标准聚氨酯海绵 (10)1.3.3高回弹聚氨酯海绵 (12)1.3.4阻燃型高回弹聚氨酯海绵 (13)1.3.5慢回弹海绵（VE海绵） (15)1.3.6阻燃型慢回弹海绵（CMVE海绵） (16)2 文件 (17)2.1验证测试 (17)2.2样品信息 (17)2.3测试报告和自我声明要求 (17)2.4变更后的验证测试要求 (18)2.4.1机械性能和结构测试，按照IOS-MAT-0076 (19)附录A：自我声明模板（标准海绵，阻燃型标准海绵（CM）, 高回弹海绵（HR）和阻燃型高回弹海绵（CMHR）） (20)附录B：自我声明模板（慢回弹海绵和阻燃型慢回弹海绵） (22)附录C：测量记录Excel数据表 (24)附录D：参考 (25)1海绵的物理性能，机械性能和结构性能要求：1.1测试方法和标准所有测试均要求无外皮海绵作为测试样品进行测试，因为海绵是否带有外皮直接会影响到海绵的物理性能。
【房地产】投资测算表——世茂—带公式
25,707
395 19,177
销项
备注（说明）
30,611 11,546
7,045 3,485 2,727 4,510 -
1,120
177
个数为考虑去化率后的 实际销售个数
个数为考虑去化率后的 实际销售个数
进项
占销售收入比例
11,052 10,647
127 9,089 1,161
56 213
406 308
1,540
单价
12,711 13,000
12,500 8,500 20,000 11,000 -
不含税销售总额 (万元) 306,111 115,455 70,455 34,852 27,273 45,102 -
含税销售总额 (万元) 336,722 127,001 77,500 38,337 30,000 49,612 -
4.5% 2.0%
1、本表格仅仅黄色部分可填写，其他部分均为公式不得修改及填写
总成本合计
218,741
含税金额 (万元) (c=a*b)
进项税计算
进项税率
专票取票比 例
进项税(万元)
189,558
10,647
70,132
-
65,600-2,697- Nhomakorabea-
-
-
-
-
1,834
-
3,280
127
109 6%
60%
开发成本测算表
税务筹划系数
0%
科目编号
科目
测算基础
说明
数值 (a)
建面单方 (元/平米)
(b)
一、开发成本
总建筑面积
366,897
reach法规限制物质清单
REACH法规限制物质清单（REACH附件17）作者：HSF中心 2012-05-02 08:49某些危险物质、混合物、物品在制造，投放市场和使用过程中的限制第一栏物质名称、物质组名称或混合物名称第二栏限制条件1. 多氯三联苯(PCTs)不可投放市场或使用：——作为物质；——在混合物中，包括废油，或者在设备中，浓度大于50mg/kg( 质量分数计%)。
?2.氯乙烯CAS 号75-01-4 EC 号200-831-0不可用于任何用途的气雾抛射剂。
含有该物质作为抛射剂的喷雾器不可投放市场。
?3.根据第1999/45/EC 号指令或满足(EC) No1272/2008条例规定的以下危险分类定义的液体物质或混合物。
(a) 危险分类~,,,2.8 A型和B型，,,,第1类和第2类，第1类和第二类，以及 2.15A型~F型(b) 危险分类~,对性功能和生育能力，或对发育的不利影响，除麻醉外的效果，和(c) 危险分类(d) 危险分类?1. 不得在以下场合使用：——通过不同的相产生光或色彩效应的装饰物，例如装饰性的灯或烟灰缸。
——戏法和魔术，——由一人或者多人参与的游戏，或任何具有类似目的的物品，甚至具有装饰性外貌2. 不符合第 1 款要求的物品，不得投放市场。
3. 如果它们含有着色剂或香料，或两者同时含有的情况下，除非基于财政理由，否则不得投放市场，如果它们：——可用作供应给一般公众的装饰性油灯的燃料，且——存在呼吸危险且被标记为R65或H3044. 供应给一般公众的装饰性油灯不得投放市场，除非它们符合欧洲标准化委员会（CEN）采用的欧洲装饰性油灯标准（EN14059）5. 在不与共同体有关规定的危险物质和混合物的分类，包装和标签的执行情况相抵触的条件下，供应商应确保在投放市场前，需满足下列要求：(a)用于出售给一般公众的被标记为R65或H304的灯油，并具有明显标记，标志醒目而难以擦掉的如下字样：“请将装有此液体的灯置于儿童无法够及处”，并于2010年12月1日起，标记“只要喝一口灯油，甚至吮吸一下灯芯都可能导致危及生命的肺损害”，(b)用于出售给一般公众的被标记为R65 或H304的打火机液体，于2010年12月1日起，标有如下醒目而不可磨灭标志着：“只要喝一口打火机油可能导致威胁生命的肺损害”；(c)用于出售给一般公众的被标记为R65或H304的灯油或打火机液体，于2010年12月1日起应封装在不超过1升的黑色不透明的容器中6. 不迟于2014 年6 月1 日，委员会因要求欧洲化学品管理局编写一份与现存的第69 条条款相一致的档案，以禁止用于供应给一般公众被标记为R65 H304的烧烤打火机液体和装饰灯燃料7.第一次将被标记为R65 或H304的灯油和打火机液体投放市场的自然人或法人，应于2011 年12月1日以及其后每年，向有关会员国的主管机关提供有关数据，以替代标记为R65 或H304的油灯和烧烤打火机液体，会员国应使这些数据提供给委员会。
SSQA Training for Suppliers 2012 Rev C 02-17-12中文
February 2012
Applied Materials Confidential/ Suppliers
Welcome & Introductions
▪ Thank you for your individual commitment to Quality and Reliability and SSQA partnership with Applied Materials in the journey to achieve Customer Satisfaction.
or Fire Department
Applied Materials Confidential
5
Applied Materials / Suppliers
Course Objectives / Outline – Day 1
▪Understand SSQA process, methods, and tools;理解SSQA过程、方法和工具
6
Applied Materials / Suppliers
Course Objectives / Outline – Day 2
▪Understand SSQA process, methods, and tools;
– Key Quality Element Requirements – Case Study Workshops
4
Applied Materials / Suppliers
5
Evacuation Procedure
Stop working immediately and remain calm Walk to the nearest exit and leave the building Proceed directly to the assigned evacuation assembly area for your
ASTM D 5927-03
2.1 ASTM Standards: D 883 Terminology Relating to Plastics2 D 1600 Terminology for Abbreviated Terms Relating to
Plastics2 D 3892 Practice for Packaging/Packing of Plastics3 D 4000 Classification System for Specifying Plastic Mate-
ISO 527-1:1993 Plastics—Determination of Tensile Properties—Part 1: General Principles
ISO 527-2:1993 Plastics—Determination of Tensile Properties—Part 2: Testing Conditions
INTRODUCTION
This material specification is intended to provide a callout system for thermoplastic polyester materials based on ISO test methods.
1. Scope*
1Байду номын сангаас4 This classification system and subsequent line callout (specification) are intended to provide a means of calling out plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection should be made by those having expertise in the plastic field after careful consideration of the design and performance required of the part, the environment to which it will be exposed, the fabrication process to be used, the costs involved, and the inherent properties of the material other than those covered by this specification.
【女装】2012淘宝双12精选促销好商品清单(内部使用)
香菲丽莎旗舰店 2012冬装新款女装上衣 韩版厚毛衣女潮宽装外套长袖打底衫女
osa品牌服饰旗舰店
OSA2012秋冬新款韩版女装时尚修身长款毛呢外套呢子大衣女 D23891
咪萝旗舰店
咪萝秋冬装新品 打底衫套头厚毛衣外套 女 羊毛衫宽松针织衫 女装
百思寒服饰旗舰店
百思寒 2012羽绒服中长款 新款韩版收腰貉子毛领 女装休闲爆 款潮
第一部分：女装
(提示：请点击底端选项卡切换到男装、家居等其它类目)
品牌名称
宝贝标题
苏醒的乐园旗舰店
苏醒的乐园 预售2012秋冬新款正品短款羽绒服 女装大衣外套 YRF
好评多多
秋冬新款加绒加厚铅笔裤显瘦小脚裤大码牛仔保暖棉打底靴裤子 女装
osa品牌服饰旗舰店
OSA2012秋冬装新款韩版女装修身中长款毛呢外套呢子大衣女 D23736
415
没挑中喜欢的宝贝吗？那就去双12专场里面瞧瞧吧~~
说 明： 请点 击下 边 tab
装
家居等其它类目)
12.12心愿价
259 69 232 298 359 159 138 25 299 87 38 397 257 439 95 149 178 98 58 157 199 329 79 67.5 149 18 88 108 189 258 35 238
799 848 468 338 19 316 384 599 196 1998 830 198 1199 1198 319 588 218 458 598 699 998 328 240 169 1898 158 138 99 640 116 498 498 198 1068 798 76
boksen
优家居
3750秋冬新款韩版女装拉绒打底裤袜子秋冬加厚显瘦九分裤保暖
BEEG2015秋冬商品需求
冬五
12.5
都市
11.25
摩登
11.25
休闲
都市 1 4 2 0 0 4 1 0 1 0 0 0 2 2 0
合计 摩登 1 3 3 2 3 4 0 1 1 3 2 2 1 0 1 11 0 1 1 4 100 休闲 0 0 2 0 1 2 0 0 1 0 0 0 0 1 0 4 0 3 0 3 47
高 1199 1599 1399 1399 1399 1599 5999 4999 2999 2999 2599 3599 2999 3199 2999 6999 5999 5999 7999 2999 99999 4599 2599 2599 主力价格 1099 1299 999 999 999 1199 4599 3599 2599 2599 1999 2999 2599 2799 2199 4999 4599 3599 5599 2599 89999 3599 1999 1999
9.5 都市 1 1
冬一 9.15 摩登
9.10 休闲
9.25 都市 2
冬二 9.25 摩登 1 1
9.25 休闲
10.15 都市 1
冬三 10.10 摩登 2
1
1 1
1
1 1 1
1 1 11 111来自1 112
2
1 1 1 1 1 1 1 1 1 1 13 1 1 17 1 1 1 1 1 1 1 1 1 1
价格带（吊牌价）
休闲
衬衫
长袖衬衫（雪纺、真丝等） 1099
1
1
价格带（吊牌价） 大类 类别 货品名称 真丝连衣裙 毛呢连衣裙 连衣裙 针织连衣裙 皮连衣裙 印花连衣裙 裙类 梭织连衣裙 包臀裙 蛋糕裙 半裙 A裙 中长裙 皮短裙 百折裙 呢短裤 短裤 梭织短裤 皮短裤 裤类 长裤 九分裤 直筒长裤 皮长裤 哈伦裤 合计 低 2199 2199 1599 3199 1999 1599 899 899 899 999 2199 899 999 799 2199 899 899 2199 899 高 3999 4599 2999 5999 2999 2999 1599 1599 1599 1899 2999 1599 1399 1299 2999 1599 1599 1599 3299 1599
国内国际知名男装品牌汇总及分析
Hugo Boss 波士2 Gianfranco Ferre3 CalvinKlein 卡尔文〃克莱恩4 GUCCI 古驰5 Dolce&Gabbana 多尔切和加巴那6 Prada 普拉达7 Christian Dior 里司汀〃迪奥8 Domma Karan （美国品牌）9 Giorgio Armani （意大利品牌）10 Zegna 杰尼亚世界知名男装品牌世界知名男装品牌：W＆LT，COMMEdes GARCONS，Dunhill登喜路，PoloRalphLauren简称Polo保罗，Aquascutum雅格狮丹，Paul&Shark博鲨，Lyle&Scott金鹰，BURBERRY(英国)，CERRUTI(意大利)，VERSACE(意大利)，GIVENCHY(法国)，RALPHLAUREN(美国)，Walter，川久保玲Hugo BossHugoBoss在国际男装市场上占有举足轻重的地位，这一点从其行销全世界80多个国家的通路即可得到有力的证明。
不鼓吹设计师风格的Boss，完全以强力放送阳刚味十足的广告形象，传达一种大众化的男性服装风格。
这个崛起于70年代的德国品牌，不论设计或形象都非常男性化，而且是那种不化妆，也不戴多余的首饰，很注重社会认同的男性形象。
此品牌在1923年由HugoBoss创建，以生产工作服、防水套装、雨衣和制服起家，一直到1972年才正式涉足时装界。
Boss男装有很完备的系列商品，是许多中高级主管心目中的标准典范。
并且，在品质和做工上，维持欧洲最大男装生产商的一流水准。
Walter此品牌崛起于‘91年秋冬季，其名称是“狂野及致命的废物”(Wild andlethaltrash)的缩写，基本上它跟设计师Walter Van Beirendon ck的名字缩写很接近。
Walter所设计的商品基本上为“无性别主义”。
Walter对服装观点是没有性别差异的，因此他设计的衣服，男人、女人都可以穿。
2014年宁波房地产市场年报
2014.3.26
2014 年 4 月
2014 年 4 月
2014.5.7
2014 年 6 月
2014.6.19
2014.12.22
国土部 国土部 国土资源部 国土部
国土部 国土资源局
国务院
出健全房地产市场调控长效机制。同时，《规划》也提 出要建立以土地为基础的不动产统一登记制度。
26 日召开的不动产登记工作第一次部际联席会议提 出，用 3 年左右时间全面建立不动产统一登记制度； 用 4 年左右时间，运行统一的不动产登记信息管理基 础平台，实现不动产审批、交易和登记信息实时互通
44.47%
7128.9 3424.0
48.02%
5405.2 2999.0
55.48%
2014 年 1-9 月，全市实现商品销售额 9666.3 亿元，同比增长 16.6%，增速比上半年提 高 2.1 个百分点。实现消费品零售总额 2097 亿元，增长 13.4%，增速比上半年提高 0.3 个 百分点，其中限额以上贸易单位实现消费品零售额 1077.9 亿元，增长 12.3%。分城乡看， 城镇实现消费品零售额 1728.4 亿元，增长 12.6%，乡村实现零售额 368.6 亿元，增长 17.7%， 快于城镇 5.1 个百分点。分商品类别看，限额以上贸易企业商品零售中，汽车类、石油及制
品类分别实现零售额 392.1 亿元和 141.5 亿元，同比分别增长 9.1%和 12.1%，合计对批发 零售业限上零售额增长的贡献率为 42.7%；居住类商品保持快速增长，家用电器、家具、建 筑装潢材料类商品零售额分别增长 29.2%、41.1%和 156.2%；生活必需品类商品增势平稳， 食品类、服装类商品零售额分别增长 7.5%和 16.6%。 图 1-5 2009 年-2014 年宁波市社会消费品零售总额走势