Car alarm system CS100

CAR ALARM SYSTEMOPERATING INSTRUCTIONI.Function Introduction1、ArmPress “” button of remote control, the turning light will flash one time, and siren will beep one time, car door will be locked automatically, and status indicator LED will flash.the system will be under arming status in 3 seconds.If the ignition key stays at “ON” position, there is only locking function.2、Mute armingPress “” button of remote control, The turning light flash one time without siren sound, door locked, status indicator LED flash, the system will be under arming status after 3 seconds.3、DisarmPress “” button of remote control, The turning light flash two times, siren sound two times, car door will be unlocked automatically.If the ignition key stays at “ON” position, there is only unlocking function.4、Auto rearmingAfter disarming, if the door was not opened or engine was not started, the car will be armed and the door will be locked automatically after 30 seconds.5、Sound car finding4 buttons remote :Press "" button of remote control, Siren sound for 15 seconds, turning light flash for 15 seconds. Press any button to stop sound car finding.3 buttons remote: press for 2 seconds in armed mode, the siren beeps for 15 seconds and turn lights flash(no beep in silent mode), which indicates the location of the car. .press any button to stop6、Silent car findingUnder mute status, press "" button of remote control, the turning light flash 15 times without siren sound. Press any button to stop silent car finding.7. Stop alarming with extra secureUnder alarm status, press button “” or “” or “” of remote control, turning light will stop flashing, siren will stop alarming. The system is still in arming status.8. Trunk releaseUnder disarm states, press the button "" of remote control for 2 seconds. Trunk will be released. The siren beep once.Note: It is only available for the car equipped with trunk release switch.9. Emergency panic alarm4 buttons remote:When engine is running, Press"" button of remote control for 2 seconds, the siren will beep for 30 seconds with the flash of turn lights, Press any button to stop alarming.3 buttons remote:：In the course of driving，press for 2 times continuously，the siren will beep for 30 seconds with the flash of turn lights. Press any button to stop.10. Anti-hijack10.1、Anti-hijack by remote control4 buttons remote:When engine is running, press "" button of remote control for 2 seconds, After the turning lights are on, press “” button for 1 second. At this time the turning lightswill flash, and the siren will beep periodically within 30 seconds and continually beep after 30 seconds till press “” button to exit.3 buttons remote:：long press for 2 seconds，then press for 1 second，At this time the turn lights will flash, and the siren will beep periodically. Then engines will be stopped 15 seconds later. Another press of can stop the alarm.11、Remind to Set ArmWhen ACC OFF and the door have closed. After 10 seconds, there will be “Bi-Bi-Bi” and turning light flash 3 times, which remind the owner to arm his car.13、Memorize triggered alarmIf the alarm is triggered, the system will memory triggered alarm under arming state, when disarming and open door, turning lights will flash for 3 seconds, siren will beep once, reminding the driver to check the car.14、Door-opened warningIf the door is opened after the car is disarmed, the turning lights will flash for 15 seconds to warn the other drivers behind.16、Automatic central door lockWhen driving, doors will be automatically locked upon first brake after 15seconds, Turn ignition OFF to unlock doors.17、State memoryThe alarm system will memory the condition before the power is cut off.18、Flash Mode of LEDIn Armed Mode: LED flashes twice, and stops for 1 seconds…Triggered by Shock: LED flashes 3 times, and stops for 1 second…Triggered by Switch: LED flashes for 2 seconds, stops for 2 secondsDisarmed after Being Triggered: LED flashes for 3 seconds…19. Two Stage Shock SensorIf the car is shocked slightly in arming status for the first time, the turning lights will flash for 5 times, and siren will beep for 5 times. If the car is shocked continuously in 15 seconds, the siren will keep beeping for 25 seconds with light flash.20. Alarming IdentificationThere are two alarming ways. First, if there is a trigger, such as bump, and knock on window, the siren will beep intermittently. Secondly, triggers except shock trigger, such as door open, ignition on, will induce continuous beep.23. Shift Electronic Lock and Air Compressor LockThe system is connected to air compressor lock when the JP-1 is disconnected, while connected is electronic lock.Note: JP must be shifted when power is off24、Emergency DisarmingIn case the transmitter is lost or broken, use following ways to disarm the system:Turn ACC on, keep stepping brake and closed door, press the learning switch on main board for 3 seconds, then the system shall disarmed, you can drive the car normally.25、Learning CodeUnder the disarming state, press the learning button for 3 seconds , which will make the turning lights flash for 5 seconds. Then press any button of the remote control for 3 seconds to do code memorizing within 5 seconds, The turning light will flash for 3 times, and the siren beep 3 times, which shows the system recognizes this new remote control. After one remote control was memorized, the system will keep time delay for 5 seconds. Press anybutton of the second remote control for 3 seconds, the turning light will flash for 3 times, and the siren beep for 3 times, which shows the second one learns code successfully. up to 2 remote control can be memorized.II.Installation1. Installation of MainframeThis mainframe is suitable for a car, whose negative points of a 12V power are connected to the iron. The mainframe should be installed under the meter. First of all, please select a place to install, and then connect wires of this system to the ACC, turn lights, brake lights, power and other ports according to the Wiring Connection.2. Installation of the Shock SensorAfter the mainframe is installed, fix the shock sensor close to the car or meter. Then adjust the sensitivity of the sensor, which depends on the size of a car or requirements. Turn the button on the sensor deasil to increase the sensitivity, and the widdershins to decrease the sensitivity. The factory setting is moderate sensitivity.3. Installation of the Central LockThere are installation solutions for several typical cars makes.A. If there is no electric lock in the car; we suggest the owner install a central lock. (Picture2)B. If there is a single point central lock system in a car; we suggest the owner fit an actuator to the driver's door. (Picture 4)C. If there is a multipoint central lock system in a car, it is only need to identify the negative and positive points. (Picture 2-3)D. If there is a multipoint vacuum central lock system, using a compressor, in a car, there is a short circuiting ring to select. (Picture 5)V. Trouble ShootingMany apparent malfunctions are caused by maladjustment and incorrect connection. If you encounter any troubles listed in the following table, please check and adjust according to the methods. Should the troubles still persist, contact the dealer.Troubles Methods of Checking and AdjustmentThe siren beeps all the time and cannot be released by remote control after this system is installed. 1.Check whether the ports are plugged on the contrary.2.Check whether the wire is connected correctly.3.Check whether the fuse of the mainframe is burned out.4.Check whether the model of mainframe and that of remotecontrol is the same.5.Check whether the switch position is correct.Parked and armed, this system alarmswhen a truck or a cart passes by.Check and adjust the sensitivity of the shock sensor.There is no beep when it is triggered. 1.Check the siren.2.Check the connection wire between the siren andmainframe.The LED on remote control is not on during the course of operation. 1.Check the battery of remote control, which should not belower than 10V.2.Check whether the power is weak as it is used frequently.3.Check whether the frequency is adjusted improperly.4.Check whether the remote control is soggy.5.Check whether the remote control is broken.Notice:＊ It is suggested to contrast one remote control with another.＊ If both remote controls fail, please check the mainframe, connection points, and power supply.It is no need to open the mainframe.After being armed, this system beeps in 10 seconds, and the same situation repeated after it is disarmed. 1. Check whether the shock sensor works.2. Check the sensitivity of the shock sensor.3. Check whether the LED for shock sensor works.＊ It is suggested to check whether the wire for brake light is in place.＊ Check whether the PIN. SW is closed.The central lock doesn’t work or is abnormal. 1. Check the actuator. 2. Check the wire, fuse.3. Read the installation instruction and wiring connection for central lock.VI. Safety Precaution for Mainframe Installation1.Read the Operating Instruction and wiring connection carefully before the installation.Please make out electro circuit of car first.2.The mainframe should be installed away from high temperature, humidity and otherelectronic items. Plug the wire plug into the mainframe, and wrap the wire top with a tape. Please take out the control wires, such as power supply wire, ignition wire, and light wire, door open signal wire. If there is no door open signal wire, it is needed to install corresponding sensor switch.3.The power supply wire should be installed after all other wires being installed. Pleasewrap all the connection point with tape.4.It is suggested that the antenna should be installed close to the windshield. Any antennafolding, cutting and grounding is prohibited.5.The shock sensor should be pasted close to the car. Adjust the sensitivity to a good level.6.If the remote control distance shortened and the LED on remote control is dim, pleasechange the battery.7.Remote controls are precise parts. Never drop or wet it.VII. Quality Warranty1. This system is warranted to be free of defects in material and workmanship for 1 year from the date of purchase. With the Warranty Card, purchaser can replace or repair the defect in the product at the maintenance agency.2. This warranty doesn’t extend to any defect, malfunction or failure caused by abuse or misuse by the Operating Instruction. In no event shall be the manufacturer is liable for any alarm system altered by purchasers.Warranty CardMode________________________ Product No.________________________ Date of Purchase____________________ Date of Production___________________ Maintenance Record__________________________________________________________ __________________________________________________________________________ _________________________________________________________________________ Dealer_____________________________。