高压清洗机说明书
高压清洗机使用说明书及故障排除法和简单的维修处理
成都力锋产品使用说明书一、使用说明1、开机前的准备：a、开机前检查进水管过滤器安装正确。
b、开机前必须检查箱体机油到油窗一半。
c、开机前安装进水管，注意：进水管必须可靠连接（垫上進水管橡膠墊Φ26*Φ14）。
2、新机第一次使用时，可将过滤器先不装，将接过滤器一端与自来水管道连接，打开自来水阀门，按动清洗机主开关，使电机工作，待出水管出水量大于未开机状态时，再工作5秒左右，停机。
将工厂原配的过滤器可靠地连接后放入储水罐底部。
使用储水罐时，必须加注清洁的水源3、出水管连接：把高压胶管的接头与增压泵出水管口上的接头相连；另一头与水枪上的接头相连。
4、喷头选择本机所用的喷头一定要使用原厂提供的配套喷头5、清洗作业时，喷头与被清洗面得距离不宜太远，一般不超过10公分。
因喷头的冲击力是随喷射距离的增大而减小。
6、正常状态下，清洗压力不超过额定工作压力为宜，若有特殊需要时，也可将机器压力升到最高压力，但不建议机器在最高压力下长期运转。
7、清洗结束松开扳机关闭水枪后，本机器会自动关停电机。
若较长时间不使用机器，建议关闭电源开关，打开水枪扳机释放内部压力。
使用完毕，必须将水枪内压力完全释放8、使用时，泵体的泄水孔有水滴出，并不影响使用，属正常运行。
9、该机长时间闲置后使用：由于单相电机起动力矩较小，如按下起动开关，电机发出嗡嗡声（电机并不远转），应立即按停机按钮，反复二，三次，电机即能运转；如果电机仍然不能起动，请拆去电机风扇罩壳，用手转动风叶二，三周后，再启动电机。
并在停机状况下重新装好风扇罩壳。
二、保养1.每100小时更换一次机油，建议使用CD15W-40机油，正确使用机油对保证机器使用寿命非常重要。
2、如遇寒冷天气有结冰时或长期不用时，应将机内剩水排尽，方法是将进水管离开供水系统，开机脱水远转1分钟左右。
同时拆下进水管与出水管以排尽管中剩水。
高压清洗机内部积水结冰后会引起电机堵转，造成电机烧机等严重后果。
三、安全用电注意事项1、项目之安全检查a、经常检查电动机引接线是否牢固可靠完好无损。
高压清洗机的使用说明
当清洗封闭的区域，像储藏罐，放置泵和空 压机在外面，并远离罐体如果清洗的位置有 可燃物质适当的提供通风装置，做 适合的准 备，避免产生静电火花，参考当地的标准。
泵：使用接地线和卡子见FIG 2使用接地螺丝 （GS）和锁紧垫（LS）和附带的接地线（U） 在空气马达的后面，拧紧螺丝，另外一端， 接在直的地线上。
冲洗
冲洗前为了减少液体喷射的伤害的风险，静电 火花，喷溅，放压，移动喷嘴 使喷枪的金属部分和泄压阀紧靠在金属桶边， 然后开启枪和阀。
编辑ppt
13
启动
打开主气阀（D） 启动喷枪在接地的金属桶内，枪的金属
部分紧紧靠着桶。 缓慢打开调压阀（E）直到泵开始运行。 缓慢运行泵直至全部排出所有空气。释
编辑ppt
6
皮肤的喷射伤害
高压的液体从喷枪，或软管泄漏，破碎的配件，会刺入皮肤，看起来像割伤，但是 严重的伤害，引起切除，需要医学外科紧急处理。 1.不要用喷枪指着任何人或身体的任何部位。 2.不要把手放在喷嘴的前端。 3.不要用手、身体、手套、布片阻挡或导流泄漏。 4.没有安装喷射保护或触发保护就不要使用。 5.不喷时锁定触发锁。 6. 当喷射停止，在清洁、检查，维护设备前，遵守压力释放程序，
活塞和吸入的止回阀，排泄泵 247599在场家设定，用于低粘度 的液体，这样的设定对泵有最小的 冲击，调整这个阀用于高粘度的液 体。见操作手册
总是在液体被泵到底部前停泵如果 液体泵干喉部密封会损坏，完成泵 作业后放压。
如果你正在泵送的液体，干的，凝 固，快速凝结，尽可能多次用合适 的溶剂冲洗系统，避免在泵里或管 理形成干液
每操作40小时检查，密封螺母， 放压后拧紧螺母。拧的要合适，过 紧会引起密封损毁。
家庭用高压清洗机操作手册
家庭用高压清洗机操作手册一、产品概述家庭用高压清洗机是一种多功能洗涤设备，可广泛应用于清洗汽车、花园道路、楼梯、阳台、家具等各类户外和家庭场景。
本操作手册将为您详细介绍家庭用高压清洗机的操作方法和注意事项。
二、安全须知1. 在操作高压清洗机之前，务必穿戴适当的个人防护装备，包括手套、护目镜和耳塞。
2. 使用前仔细阅读清洗机的用户手册，并确保理解和遵守所有安全要求。
3. 在使用高压清洗机时，请确保周围没有人员，以防止意外伤害。
4. 避免将高压喷射水流直接对准人体、动物或电器等易受损的物体。
5. 使用高压清洗机时，务必保持稳定的姿势，防止滑倒或因姿势不当造成伤害。
三、准备工作1. 在使用高压清洗机之前，确保水源供应充足，并接通电源插头。
2. 检查清洗机的电源和线缆是否完好无损，如有损坏请勿使用，并及时联系售后服务。
3. 清洗机配备了不同类型的喷嘴和喷嘴连接器，请根据需要选择合适的喷嘴，并将其紧密连接到喷嘴连接器上。
四、操作步骤1. 打开水源，确保水流畅通，并在清洗机的开关上按下电源按钮。
2. 调整清洗机的喷射压力。
根据需要，可通过旋钮或按钮来控制喷射压力的大小。
3. 将喷嘴对准需要清洗的区域，并保持适当的距离。
开始清洗前，请确保自己和其他人员都不在水流范围内。
4. 使用水枪扳机来启动喷射水流，同时以横向和竖向的方式扫射。
不要停留在同一位置太久，以免损坏清洗表面。
5. 当清洗结束时，松开水枪扳机，并关闭清洗机的电源开关。
6. 关闭水源，并等待清洗机完全停止运行后，拔掉电源插头。
五、维护保养1. 在每次使用后，请先关闭水源，并拔掉电源插头，以免发生意外。
2. 清洗完毕后，请及时清洁和储存喷嘴和连接器，以防堵塞和损坏。
3. 定期检查和更换清洗机的过滤器，保证喷嘴通畅。
如发现异常或故障，请联系售后服务进行维修。
六、故障排除在使用过程中，如果发现以下情况，请先关闭清洗机并拔掉电源插头，然后联系售后服务进行维修：1. 清洗机发生漏水或有异常声音。
高压清洗机使用说明书
高压清洗机使用说明书首先，感谢您选择我们的高压清洗机。
本使用说明书将指导您正确、安全地操作和维护该设备，确保其正常运行并延长使用寿命。
一、产品简介高压清洗机是一种专业清洗设备，利用高压水流来清洗各种表面污垢和杂质。
本清洗机采用先进的技术和高质量材料制成，具有出色的清洗效果和耐用性。
二、安全须知1. 在使用高压清洗机之前，请仔细阅读本使用说明书，并确保您已完全了解和理解所有安全须知。
2. 本机器仅供专业人士使用，不适合儿童或无经验的操作人员使用。
3. 在操作过程中，请正确穿戴个人防护装备，如防护眼镜和防护手套。
4. 在清洗机运行期间，不允许站在水流喷射范围内，以免产生危险。
5. 在停止使用高压清洗机之前，请先切断电源并等待水流完全停止。
三、操作步骤1. 准备工作a. 检查电源线和水源管道是否连接牢固，并确保水源正常供应。
b. 检查高压清洗机是否有足够的洗涤剂储存。
c. 确保喷嘴安装正确。
2. 开启高压清洗机a. 将电源线插入电源插座，并打开电源开关。
b. 打开水源开关，确保水流畅通。
c. 根据清洗需求，选择合适的喷射模式和压力。
3. 进行清洗a. 将喷嘴对准待清洗的表面。
b. 按下喷嘴扳机，开始喷射高压水流进行清洗。
c. 在清洗过程中，始终保持稳定的姿势，避免摔倒或滑倒。
4. 使用洗涤剂（可选）a. 如需使用洗涤剂，请确保洗涤剂储存容器已连接至清洗机。
b. 打开洗涤剂开关，并根据需要调节洗涤剂的流量。
c. 在清洗过程中，喷射洗涤剂和水流的组合，以获得更好的清洗效果。
五、维护与保养1. 清洗结束后，请关闭电源开关和水源开关。
拔掉电源线并排放残余水流。
2. 仔细清洗和储存喷嘴，以防堵塞或损坏。
3. 定期检查清洗机的电源线、水源管道和喷嘴等部件，如有损坏或老化应及时更换。
4. 保持清洗机的外部干燥和清洁，定期除尘和擦拭。
5. 建议定期进行维护保养，并根据使用频率更换某些易损件，保持机器的正常运行。
六、故障排除如果在使用过程中遇到以下问题，请首先检查是否存在以下情况，并及时进行修复或更换：1. 无法正常启动机器。
森猫380型高压清洗机说明书
森猫380型高压清洗机说明书一、产品概述森猫380型高压清洗机是一款专业的清洗设备，主要用于清洗车辆、建筑物、管道等大型设施。
该设备采用高压水流清洗，可以快速高效地清除污垢和污渍，同时也可以起到除尘、除锈等作用。
该设备具有多项安全保护措施，操作简单方便，是您清洗工作的理想选择。
二、产品参数1.额定功率：3.2KW2.额定电压：220V/50Hz3.额定电流：14.5A4.额定压力：160Bar5.额定流量：12L/min6.最高温度：50℃7.机器重量：85kg8.机器尺寸：750mm*480mm*980mm三、使用方法1.将清洗机放置在平稳的地面上，连接好水源和电源。
2.打开水源和电源开关，待机器启动后，根据需要调节水压和流量。
3.将清洗枪对准需要清洗的物体，按下扳机，开始清洗。
4.清洗完成后，关闭清洗枪的扳机，关闭水源和电源开关，将设备拆解清洗干净，存放在干燥通风的地方。
四、注意事项1.使用前请仔细阅读说明书，了解设备的性能和操作方法。
2.在使用过程中，请佩戴好防护设备，避免因操作不当而造成伤害。
3.在使用过程中，请勿将清洗枪对准人体或动物，避免造成伤害。
4.在存放设备时，请将设备存放在干燥通风的地方，避免设备受潮生锈。
5.在清洗设备时，请勿将清洗液直接喷向电机或开关处，避免造成电气故障。
五、维护保养1.定期检查设备的电线、插头、接头等部位，如有破损或老化，请及时更换。
2.定期清洗设备的水管、清洗枪等部位，避免堵塞和污垢积累。
3.定期检查设备的滤网，如有堵塞请及时清理或更换。
4.如设备长时间未使用，请拆解清洗干净，存放在干燥通风的地方。
六、故障排除1.设备无法启动：检查电源是否接通，开关是否正常，电线是否破损。
2.水压过低：检查水源是否充足，清洗枪是否堵塞，滤网是否清洗。
3.清洗枪漏水：检查清洗枪密封圈是否损坏，是否紧固好。
4.设备运行时有异响：检查机器是否松动，清洗枪是否堵塞，电机是否损坏。
高压清洗机使用说明书及故障排除法和简单的维修处理精编版
高压清洗机使用说明书及故障排除法和简单的维修处理公司标准化编码 [QQX96QT-XQQB89Q8-NQQJ6Q8-MQM9N]成都力锋产品使用说明书一、使用说明1、开机前的准备：a、开机前检查进水管过滤器安装正确。
b、开机前必须检查箱体机油到油窗一半。
c、开机前安装进水管，注意：进水管必须可靠连接（垫上进水管橡胶垫Φ26*Φ14）。
2、新机第一次使用时，可将过滤器先不装，将接过滤器一端与自来水管道连接，打开自来水阀门，按动清洗机主开关，使电机工作，待出水管出水量大于未开机状态时，再工作5秒左右，停机。
将工厂原配的过滤器可靠地连接后放入储水罐底部。
使用储水罐时，必须加注清洁的水源3、出水管连接：把高压胶管的接头与增压泵出水管口上的接头相连；另一头与水枪上的接头相连。
4、喷头选择?本机所用的喷头一定要使用原厂提供的配套喷头5、清洗作业时，喷头与被清洗面得距离不宜太远，一般不超过10公分。
因喷头的冲击力是随喷射距离的增大而减小。
6、正常状态下，清洗压力不超过额定工作压力为宜，若有特殊需要时，也可将机器压力升到最高压力，但不建议机器在最高压力下长期运转。
7、清洗结束松开扳机关闭水枪后，本机器会自动关停电机。
若较长时间不使用机器，建议关闭电源开关，打开水枪扳机释放内部压力。
使用完毕，必须将水枪内压力完全释放?8、使用时，泵体的泄水孔有水滴出，并不影响使用，属正常运行。
9、该机长时间闲置后使用：由于单相电机起动力矩较小，如按下起动开关，电机发出嗡嗡声（电机并不远转），应立即按停机按钮，反复二，三次，电机即能运转；如果电机仍然不能起动，请拆去电机风扇罩壳，用手转动风叶二，三周后，再启动电机。
并在停机状况下重新装好风扇罩壳。
二、保养1.每100小时更换一次机油，建议使用CD15W-40机油，正确使用机油对保证机器使用寿命非常重要。
2、如遇寒冷天气有结冰时或长期不用时，应将机内剩水排尽，方法是将进水管离开供水系统，开机脱水远转1分钟左右。
烧油高压清洗机使用说明
烧油高压清洗机使用说明一、产品概述烧油高压清洗机是一种高效的清洗设备，适用于各种工业设备的清洗和维护。
本清洗机采用燃油作为动力源，通过高压水流和专业喷嘴，能够迅速清除设备表面的污垢和油渍，提高设备的清洁度和工作效率。
二、操作步骤1. 准备工作：a. 确保清洗机的燃油箱已经加满燃油，并检查燃油管路是否畅通。
b. 检查清洗机的高压水泵和喷嘴是否安装正确，并确认水源供应是否稳定。
2. 启动清洗机：a. 打开清洗机的电源开关，确保电源连接正常。
b. 调节清洗机的压力控制阀，根据清洗需求调整清洗机的工作压力。
c. 按下启动按钮，清洗机将开始运行。
3. 进行清洗：a. 将喷嘴对准需要清洗的设备表面，保持一定距离。
b. 按下手动开关，高压水流将喷射出来，清洗设备表面的污垢。
c. 根据需要，可调整喷嘴的角度和距离，以获得更好的清洁效果。
d. 清洗机工作时，应保持喷嘴在运动，避免对同一位置进行过长时间的清洗。
4. 完成清洗：a. 清洗完成后，松开手动开关，清洗机将停止工作。
b. 关闭清洗机的电源开关，断开电源连接。
c. 清洗机的喷嘴和水泵应及时清洗和维护，以保持设备的正常使用寿命。
三、注意事项1. 在操作清洗机之前，应仔细阅读并理解清洗机的使用说明书，确保操作正确和安全。
2. 清洗机应在平稳的工作台上使用，并保持清洗机周围的工作环境干净整洁。
3. 在操作过程中，应佩戴防护眼镜和手套，以防止高压水流对人身安全造成伤害。
4. 清洗机的操作人员应经过专业培训，熟悉清洗机的工作原理和操作方法。
5. 清洗机的维护应定期进行，包括清洗喷嘴、更换燃油和检查电气系统等。
6. 在清洗机长时间不使用时，应将清洗机储存在干燥通风的地方，避免长时间暴露在潮湿环境中。
四、总结烧油高压清洗机是一种高效、便捷的清洗设备，能够有效清除设备表面的污垢和油渍。
使用清洗机时，要注意安全操作，并定期进行维护和保养，以延长清洗机的使用寿命。
希望本使用说明能够帮助您正确使用烧油高压清洗机，提高工作效率和设备的清洁度。
高压清洗机说明手册
高压清洗机说明书型号:TVE070C、TVF070CTVB080G、TVD100CTVG100C自行用时存放在室内。
本机供应电流应不少于额定电流。
使用前，请先检查延长电线，如果已损坏，请更换。
使用不适合的外延电线会有很大的危险。
不要滥用延长电线，拔插头时请不要猛拉电线。
延长电线远离热源及锋利刀口。
分离本机时，请先将插头从插座处分离。
警告：如果供给电线已损坏，必须使用专用的电线，也可让销售商或生产厂家重新装配。
警告：为了减少触电风险，在下雨和雷雨天气不要开启和操作本机。
保持所有接口干燥，并脱离地面，不要用湿手触摸插头，严禁水渗透本机。
警告：本机运行时，必须保持持续的供水，没有水循环温度将会达到危险点，会引起机内密封圈的损坏。
警告：不要使用本机用于特别寒冷处，以防止冰冻而损坏本机。
警告：此机设备只为清洁水设计，不能使用腐蚀性的化学液体。
警告：不能将本机直接对准人体、宠物及机器本身喷射。
警告：在维修保养时，必须切断电源。
警告：为了确保实用安全，请用最初的备用配件及生产商指定的配件。
假如机器损坏，没有修复以前请不要使用本机。
操作指南－连接软管到出水口，并连接喷抢到软管另一头。
－连接喷头和喷杆。
－查看过滤网是否有障碍物。
－连接供水软管。
－主要技术数据维修保养安装Array连接图１主机２供水软管３水管接合配件４进水口５高压管６自来水龙头７喷枪８电源插头注意：假如产品更新，公司将保留没有预先通知的情况下，修改说明书的权利。
EP系列高压清洗机日常使用说明
一、开机前检测
1.观察滤芯：如图所示，如果滤芯颜色由白色变得很脏，请更换
滤芯。
2.观察润滑油：如果润滑油色泽由清亮变得浑浊，请及时更换，
油量请添加到透视窗2/3处。
二、配件的正确连接
1.连接进水管：连接好后注意锁紧卡扣
2.连接喷枪：注意高压软管螺纹端需缠好生料带，再进行连接
3.连接出水高压软管：注意高压软管接头内O形圈无破损
4.连接喷头
三、开机使用时注意事项
1.注意：使用喷枪前，请先将喷头朝下倾斜45度左右，再打开
喷枪开关
2.若使用的是50-100米的高压软管，开机后需等待3-5秒，压
力便会保持稳定
四、使用过程中注意事项：水箱缺水会自动停机
五、使用结束后的检查：如果泵头下方机架板上有滴落的液体，泵
头底部有渗出物，用手触摸感知，判断是油是水，然后再作处理。
六、安全溢流阀维护保养：在压力低的情况下才需要检修溢流阀
然后，按照下图所示步骤将阀组装还原。
七、安全阀维护保养：安全阀漏水的情况下才需要检修。
高压清洗机手册（M12110 M12230）说明书
M12110M12230Instruction ManualSpare Parts ManualProduct information................................................................................................Important safety instructions...................................................................................Technical specification............................................................................................Know your machine................................................................................................Working principle....................................................................................................Preparing for use...................................................................................................Assembly...............................................................................................................Brush selection guide............................................................................................Controls..................................................................................................................Operating the machine...........................................................................................Electrical diagram..................................................................................................Accessories...........................................................................................................Upkeep of your PORT A SCRUB...........................................................................Housing - Drive Side...............................................................................................Housing-Idle Side..................................................................................................Pump housing........................................................................................................Lever and guide link mechanism............................................................................Handle group..........................................................................................................Motor,drum and bridge assembly...........................................................................Accessories...........................................................................................................3345556677,88991113,151719212325The Minuteman Machine is an ideal machine to clean floors in small and medium areas like offices,hospitals,restaurants,shopping complexes and many commercial applications.It sprays plain water /detergent solution,scrubs and picks up the dirty water -all in a single pass.The Port A Scrub has different optional brushes to suit a variety of applications.This machine can be used only on smooth even floors like Mosaic,all type of stone floors,PVC,Short-pile carpet,Wood and Profiled Rubber.It should not be used on rough uneven surfaces..PORT ASCRUB Instruction ManualThe machine must be unpacked and assembled in accordance with these instructions before connecting to the electrical supply.This machine should always be connected to a fully grounded power supply of the right voltage and frequency.Keep the power supply cord away from moving parts.During operation,hazard may occur when running machine over the supply cord.The machine must be disconnected from the mains supply (by pulling the plug out)before changing the brushes,cleaning the machine and,for maintenance.Warning!Use only the brushes/accessories strictly as per the instruction age of any other brushes/accessories can cause safety problems.Periodically inspect the cord for possible damage.The damaged cord must be replaced with the special cord available from the manufacturer or an authorized service agent.DO NOT leave the machine connected to the power supply when not in use;always remove the plug from the mains socket.DO NOT use where hazardous dust is present.DO NOT use machine near flammable liquids.DO NOT use in an explosive atmosphere.DO NOT use in gradient surface.DO NOT keep the machine with handle lowered,when the machine is in working mode.Operators must be fully trained in accordance with these instructions,able to perform routine upkeep of the machine and correct selection of brushes.Operators should be physically capable to maneuver transport and operate the machine.DO NOT run the machine dry,as this could damage the floor surface or the machine itself.Take adequate care to hold the machine firmly while installing and removing the brush.Never use excessive foaming or highly corrosive cleaning solutions.While operating on a flooded floor,always ensure that the water level does not exceed 1/4”.DO NOT operate this machine on rough uneven surface like industrial concrete floor.Do not clean the machine using water jet.Ensure all parts are fitted properly before operation.···········Guidelines for the operator (3)4Note:1. Noise levels measured at a distance of 1 meter from machine and 1.6 metres above floor, when washing a hard floor. Measurements recorded using a hand held meter.2. Handle vibration does not exceed 2.5 m/s, when operating on a smooth hard surface.3.Above dimensions are approx. Since the companies policy is to continuously improve the product, there could be changes without prior notice.2986713511412312(1)(2)(3)Tank(4)Bottom handle (5)Dirty water tank(6)Filter (7)Lid Cap (8)Boot(9)Nozzle (10)Conveyor drum (11)Brush (12)PedalTop handleLiquid discharge controlhandle1.Cleaning liquid in the fresh water tank is made to spray on the floor to be washed..2.The counter rotating brushes scrubs the floor and also throws the dirty water on the Conveyor drum.The front brush does most of the scrubbing and drying.The rear brush completes the scrubbing and collects the remaining water off the floor.3.A blade fitted to the dirty water tank wipes the drum.1. Bottom handle2. Machine body3. Pump Housing4. Auxillary Tank5. Top handle &pull cable7. Brush shafts (2)8. Screws & washers 9. Cable retainer 10. Power cord6. Handle LH & RH11. Dirty water tank 12. Hook 13. Knob (10)(11)(12)(7)(8)(9)(6)(2)(3)(4)(5)(1)L E F T B O T TO M R E A RR I GH T B O T TO M R E AR 1.Insert the two tubular handles into the bottom handle and secure them using knob (2Nos)by tightening lightly.Ensure that the handles are assembled according to their marked position and the cable holding hooks are pointing towards the rear.2.Slide the electric cable retainer into the top portion of RH handle.3.Fit the top handle over the tubular handles and secure them with washer and screw (2sets).Ensure that the label on the top handle is facing the front of the machine.Now tighten firmly both the knobs and screws alternately.Insert the dummy caps provided to cover the screws (2nos)in the top handle.4.Pass the free end of the pull cable through the plastic guide in RHHandle.5.Fixthe auxillarytank firmly into the bottom handle by holding the top handle.6.Rotate the knob to hold the auxillary tank.7.The brushes are only loosely packed in the machine for transit,therefore the brush shafts must be fitted before operating the machine.Push the shafts through the brushes from the side of the machine.To remove brushes,push the brush shaft out from the side of the machine using the fingers and withdraw the shaft.Normally standard brush type will be supplied with the machine.Brushes shall be selected according to the type of floor surface to be cleaned,and the degree of dirt to be removed,please refer Brush Selection Guide.8.Now machine is ready for use.6Refer Page 25 for Brush SelectionThis is applicable when the customer has more than one set of brushes of same type.Example :2or more sets of Standard BrushCustomers may not interested to use same brushes in Bedroom /Kitchen /germ free area which is already been used in other areas like Corridor /Bathroom /Oil or chemical deposited areas.It is difficult for the customers to identify the particular brush which is used in certain area.To make this easy,Brush buttons of colors RED,BLUE,WHITE and YELLOW are packed with the machine.Customers shall plug the buttons on the hole provided in the brush as shown.This helps the customer to identify the particular brush by keeping the button (color)as reference.(a) Hole provided for plugging button.(b) Brush with button plugged.By pressing the pedal lightly with your foot,pull back the handle a little to start the motor.The brushes and the drum starts rotating.Pulling the handle further without pressing the pedal,lowers the machine and engages the rotating brushes onto the floor.To stop working,take the handle to the vertical position.By pulling,the liquid discharge control handle up,the cleaning liquid is made to spray on the floor.The spraying stops once the liquid discharge control handle is released.Brush contact with the floor is adjustable in 4steps,contact is MINIMUM when the knob is fully down and MAXIMUM when it is fully raised.This helps you to compensate for the wear of brushes and also to control the scrubbing effect.If there is no machine movement,when the handle lower down fully (working mode),change the knob position to one step up.In the event of motor getting overloaded due to improper power supply or unexpectedobstruction to the brush/drum rotation,the over load protector trips and protects the motor from damage.If this happens,identify the cause,correct it and,reset the protector button after minimum 30seconds from tripping by pressing the over load protector manually and continue working.Slide this knob to TOP position to operate the machine.Slide this knob to BOTTOM position to move the machine from one place to other place and to park the machine.By keeping the knob to top position (working mode)and moving the machine will damage the brushes.Before the washing operation startsRecommended washing sequenceTransport/Working Model ControlBrush Contact ControlCleaning Liquid Discharge ControlMotor Overload Protector1. Fill cleaning liquid in fresh water tank (Fig-i)2. Insert the plug into mains 3-pin socket.3.Ensure that the brushes are fitted properly.4.Slide the transport/working mode control knob to TOP (working) position (Fig-ii).1. Start the machine by pressing the pedal and pulling the handle back.2. Move forward, while sparingly pulling the liquid discharge control handle (Fig-iii).This handle should not be kept pulled all the time.The duration and frequency of pulling and releasing has to be adjusted suitable to match with the type of floor, extent of dirt. etc. For ceramic & granite floors, apply very little water.7(Fig-v)5.When the dirty water tank is full,lift and pull the tank out of the machine (Fig vi).Empty the tank and wash it in running water or dip it in a bucket of water (Fig-vii).Clean the blades and push the tank into its place.1.Move the Transport /Working mode control knob to BOTTOM (Transport)position (Fig-viii).2.Disconnect the power supply by unplugging the electrical plug and wind the cable over cable holders in the handle.3.Pull out the dirty water tank and wash it completely.4.To prevent possible clogging of filter,drain cleaning liquid5.Remove the brushes by pushing the brush shaft out (Fig-ix).6.Wash the brushes either by dipping in a bucket/sink or in running water (Fig-x).7.Turn the machine sideways and wipe clean the conveyor and machine body with a damp cloth (Fig-xi).8.Re-install the brushes after washing.It is easier to push the brush shaft form the right hand side (identified by the electrical cable).9.Keep the machine in the safer place.may not handed overTransporterSide BrushTo get the maximum life of the machine ensure the following.Regularly inspect sheath,plug and cord anchorage for damage or loose connection.For maximum life wash the brushes regularly.Ensure machine is in Transport mode when not in use.Store additional brushes in a vertical position to avoid bending of bristles.Check for permanent bending of bristles in a particular direction.This may occur if the machine is operated for several days without removing the brushes,which is not recommended.If this occurs,reverse the brush so that the bent bristles are automatically straightened.This may wear out after years of use.If this occurs the water collection performance will decrease.It should be replaced by an authorized ServiceAgent.The filter prevents clogging of the spray nozzle and should be periodically e pressurized air/water for cleaning.If the spray of the nozzle become blocked,slide the nozzle cover off and remove nozzle wash in clean water and clean using a pin and refit.·Supply cordBrushesWiper BladeSolution feed filterNozzle maintenance (9)The simply fitted trolley provides for ease of movement when transporting the machine.Installing the Transporter1.With the machine handle in the upright position place the transporter centrally alongside the machine.2.By holding the machine firmly, strap the velcro with the machine to fix the transporter.3.Ensure that the velcro strap properly wrapped around the bottom handle.4.Now the transporter is ready to use.The machine can then be maneuvered easily whilst holding the top handle.To wash the edges,the side brush shall be used.Switch off and unplug the machine before fitting the side brush.1.Remove the front brush and brush shaft.2.Fix the shield assembly and screw it into the side plate and tighten.3.Insert the side brush through the shield and main brush.Fitting the side brushUsing the side brush1.Tilt the machine at an angle move forward.This way,the dirty water thrown bythe side brush will be collected by the rear brush.e side brush only for washing the edges.322524105116116a11115b1949848319539787208880114101919728115a115b111914359427313V81034 9211563V71911193622122774610Housing-Drive Side Spare Parts ManualRef. No PartNoDescription Size Qty1925032CSK SCREW M4x104 2925003CRPH SCREW M3x66 7925051CSK SCREW M6x143 9925114ALLEN SCREW M6x102 10925027ALLEN SCREW M6x167 11925031ALLEN SCREW M6x202 13925033WASHER 4.2x12x1.64 19925056BEARING60032RS9 20925062BEARING6082Z1 24925001BELT5005M1 25925002BELT4255M1 28925012WASHER2 32925018BUMPER1 34925026BUMPER1 42925047BRUSH SLIDER1 43925048SLIDER HOUSING1 46925054SEAL2 49925064PINION1 53925073DRUM SPROCKET1 59925092PIN1 62925099O'RING2 63925102SHIELD1 73925186SELF TAPPING SCREW4 77925130CAP2 80925227GEAR HOUSING1 83925181HOUSING SPROCKET1 84925182SEAL1 87925193GEAR–LH1 88925194GEAR-RH1 92925219SHIELD2 93925220ROLLER2 105925249BUMPER SLEEVE3 111925804BRUSH SPROCKET2 114925813GEAR SPROCKET2 115925815IDLER ASSY1 115a925075SPROCKET1 115b925046HUB2 116925816IDLER ASSY1 116a925061SLEEVE1 212925221STUB AXLE1 V7925150DRIVE HOUSING1 V8925319COVER1V2V3133751094b94a 9412986131132892172736811610039909596999893622123318868171061524218919792774632105V5910V834137358594319263Housing-Idle SideRef. No PartNoDescription Size Qty1925032CSK SCREW M4x104 2925003CRPH SCREW M3x66 6925039CSK SCREW M5x252 9925114ALLEN SCREW M6x102 10925027ALLEN SCREW M6x165 13925033WASHER 4.2x12x1.64 15925100WASHER 6.4x12x1.61 16925151WASHER9x17x1.61 17925110SPRING WASHER M61 18925059TOOTHED WASHER M61 19925056BEARING60032RS2 21925063WIRE TIE3 32925018BUMPER1 33925019BUSH2 34925026BUMPER1 39925040STUB AXLE1 43925048SLIDER HOUSING1 46925054SEAL2 58925083TRANSPORT SLIDER1 59925092PIN1 62925099O'RING2 63925102SHIELD1 68925109FAN COVER1 72925116GROMMET1 73925186SELF TAPPING SCREW6 75925124CAP1 77925130CAP2 79925147STOPPER1 81925500PEDAL1 86925192NUT2 89925199CONNECTOR1 90925200SWITCH2 92925219SHIELD2 93925220ROLLER2 94925529SOCKET ASSY1 94a925074SOCKET1 94b925076TERMINAL3 95925501CABLE1 96925502CABLE1 98925504CABLE1 99925505CABLE1V2V3133751094b94a 9412986131132897273681161003990959699982193622123318868171061524218919792774632105V5910V834137358594319263Housing-Idle SideRef. No PartNoDescription Size Qty100925152SPRING-PEDAL1 105925249BUMPER SLEEVE3 106925161CSK SCREW M4x81 129925015LEVER SWITCH ACT1 131925041INSULATION TOP1 132925044INSULATION BOTTOM1 133925101NUT1 188925207SLEEVE TIE ROD3 212925221STUB AXLE1 242925347CLAMP WIRE1 V2925534CAPACITOR(M12230)1 V3925173CIRCUIT BREAKER(M12110)1 925166CIRCUIT BREAKER(M12230)1 V5925153IDLE HOUSING(M12110)1 925154IDLE HOUSING(M12230)1 V8925319COVER11651871841183M12110185180159124516818116472244V2155101176V9169186182163167158154174173121123123a122b16224724627117010272175177248165270Pump HousingRef. No PartNoDescription Size Qty1925032CSK SCREW M4x105 72925116GROMMET2 101925160O-RING-PUMP1 102925077FILTER1 121925832DIRTY WATER TANK1 122b925162LID PAD2 123925836LID-DIRTY WATER1 123a925132LID-DIRTY WATER1 154925128HOSE-275(10.8)1 155925163INSULATION1 158925164HOSE CLIP1 159925165NOZZLE1 162925167BOOT1 163925168SCREW M3X302 164925169HEX NUT M32 165925170HEX NUT M47 167925187SWITCH2 168925204STRIP LID2 169925224EXTENSION BUSH1 170925233HOSE-165(6.5)2 173925261HOSE CONNECTOR1 174925262BOOT-LID1 175925506CABLE1 176925511ADAPTOR NOZZLE1 177925573CABLE1 180925171SEAL NOZZLE1 181925173BASE SWITCH1 182925174LEVER1 183925175CLAMP1 184925176SUPPORT RING2 185925177PUMP HOUSING1 186925178LID1 187925179SPACER1 245925013CSK SCREW4 270845039WASHER4 V9925210PUMP(M12230)1For M12110244925011CLAMP CAPACITOR(12110)1 246925016GROMMET(M12110)2 247925020PUMP HOUSING(M12110)1 248925021CABLE(M12110)1 271814313CSK SCREW M4X154 v2925536CAPACITOR(12110)1 v9925203PUMP(M12110)1119a118a1196411876264128120120a119a82119297841477691267611345Lever and Guide Link MechanismRef. No PartNoDescription Size Qty4925104CRPH SCREW M4x122 26925008CLEVIS PIN5 29925014CLEVIS PIN1 41925043LINK1 45925053SHIELD8 47925055LEVER2 64925105LEVER BUTTON4 76925129CIRCLIP6 78925139LINK GUIDE1 82925180SPRING1 91925212BUSH1 113925810WHEEL4 118925822LEVER ASSY1 118a925085LEVER1 119925823LEVER ASSY2 119a925086LEVER2 120925824LEVER ASSY1 120a925087LEVER1 128925050LEVER SWITCH1V423355718936010415344711211748114135126124172160160a 160c 160b 179161d 161161c 161b 161a 15222423173229225732306545222522722866224226Handle GroupRef. No PartNoDescription Size Qty3925058CRPH SCREW M4x81 4925104CRPH SCREW M4x1210 11925031ALLEN SCREW M6x202 12925088WASHER 6.4x18x24 23925098CABLE RETAINER1 35925028CLAMP1 44925049PULL HANDLE1 48925057CAP1 52925069BASE-CABLE HOLDER2 57925082CLAMP1 60925096NUT1 65925106SPRING6 66925107WASHER6 71925115PLUG2 73925186SELF TAPPING SCREW10 104925184PULL CABLE-P1 117925818TOP HANDLE1 126925103KNOB2 135925089BOTTOM HANDLE1 152925127GASKET1 153925111TANK-4l1 160925117BASE VALVE1 160a925118BASE1 160b925119SEAL1 160c925120CAP-VALVE1 161925135VALVE1 161a925122BODY-VALVE1 161b925540SEAL1 161c925123SPRING1 161d925125CAP-SPRING1 172925260PLATE1 179925126NUT1 189925274SLEEVE1 224925305KNOB-CABLE HOLDER-II2 225925306KNOB-CABLE HOLDER-I2 226925307KNOB-TANK HOLDER-LH1 227925308KNOB-TANK HOLDER-RH1 228925339BASE-CABLE AND TANK HOLDER2 229925340GUIDE1 230928633PIPE-LH1 231928634PIPE-RH1 V4925922(M12116)POWER CORD1 925920(M12235)POWER CORD1 925923(M12235)POWER CORD-UK1134134b134aV6287V15011227315415556623755381422677069851Motor, Drum and Bridge AssemblyRef. No PartNoDescription Size Qty5925136HEX NUT M63 7925051CSK SCREW M6x144 8925090ALLEN SCREW M4x102 14925080WASHER 5.2x10x1.62 15925100WASHER 6.4x12x1.63 22925084GRUB SCREW M5x122 27925009BUSH4 28925012WASHER4 31925017WASHER6 37925037SPRING1 38925038SPRING1 50925065HEX SHAFT2 51925068WASHER2 54925078TIE ROD3 55925079SHAFT1 56925081ROLLER6 62925099O'RING12 67925108BUSH2 69925112BUSH1 70925113BUSH1 112925808BRUSH SHAFT2 134925067DRUM ASSY1 134a925070DRUM1 134b925071DRUM SLEEVE1 V1925762MOTOR(M12110)1 925761MOTOR(M12230)1 V6928548BRIDGE1AccessoriesSide Brush Group-3423456176886a6a6b6c9112101011103254TransporterAccessories1234566a 6b 6c 789101112925881925155925156925157925158925137925138925140925141925159925142925143925144925878925879FRAME CLAMPFIXED STRIP (VELCRO)FLEXIBLE STRIP(VELCRO)PLATE TYREBUSH-WHEEL RIM WHEEL RIM TYRE-MAIN WHEEL CAP WHEEL WASHER CIRCLIP A17x1CRPH SCREW M4x25STOPPER TOP STOPPER BOTTOM925904-TRANSPORTER 111112422242612SL NO PART NO DESCRIPTIONQTY12345925901925902925903925908925990BRUSH GROUP-STD BRUSH GROUP-POLISHING BRUSH GROUP-SCRUBBINGBRUSH GROUP-ESCALATOR (NYLON)BRUSH GROUP-ESCALATOR (SILICON CARBIDE)BRUSH GROUP SL NO PART NO DESCRIPTION123456SHIELD BUSH SHAFT SIDE BRUSH WASHERALLEN SCREW M5x20SIDE BRUSH GROUP DESCRIPTION SL.NOQTY 925766925172925764925855925145925146925907STANDARD 925766925172925764925595925145925146925927ESCALATOR 111111Note:Since the companies policy is to continuously improve the product, these could be changed without prior notice.Minuteman International Made Simple Commercial Limited WarrantyREVISION DEFFECTIVE 7/1/2008Minuteman International, Inc. warrants to the original purchaser/user that the product is free from defects in workmanship and materials under normal use. Minuteman will, at its option, repair or replace without charge, parts that fail under normal use and service when operated and maintained in accordance with the applicable operation and instruction manuals.All warranty claims must be submitted through and approved by factory authorized repair stations.This warranty does not apply to normal wear, or to items whose life is dependent on their use and care, such as belts, cords,switches, hoses, rubber parts, electrical motor components or adjustments. Parts manufactured by Minuteman are covered by and subject to the warranties and/or guarantees of their manufacturers. Please contact Minuteman for procedures in warranty claims against these manufacturers.-- Use of replacement filters and/or prefilters not manufactured by Minuteman or itsdesignated licensees, will void all warranties expressed or implied.A potential health hazard exists without original equipment replacement.All warranted items become the sole property of Minuteman or its original manufacturer, whichever the case may be.Minuteman disclaims any implied warranty, including the warranty of merchantability and the warranty of fitness for a particular purpose. Minuteman assumes no responsibility for any special, incidental or consequential damages.This limited warranty is applicable only in the U.S.A. and Canada, and is extended only to the original user/purchaser of this product. Customers outside the U.S.A. and Canada should contact their local distributor for export warranty policies.Minuteman is not responsible for costs or repairs performed by persons other than those specifically authorized byMinuteman.This warranty does not apply to damage from transportation, alterations by unauthorized persons, misuse or abuse of the equipment, use of non-compatible chemicals, or damage to property, or loss of income due to malfunctions of the product.If a difficulty develops with this machine, you should contact the dealer from whom it was purchased.This warranty gives you specific legal rights, and you may have other rights which vary from state to state. Some states do not allow the exclusion or limitation of special, incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions and limitations may not apply to you.MPV 13, one year partsV-14, One year parts, one year laborMPV 14 and 18, two years parts, one year labor RapidAir blower, one year parts, one year laborExplosion-Proof Vacuum, one year parts, one year labor Pneumatic Vacuums, three years parts, one year labor TRS 14, one year parts, one year labor(Not to exceed two hours)(Not to exceed two hours)(Not to exceed two hours)Ninety days0-3 months replacement, 4-12 months pro-rate Ten years, no additional labor111 South Rohlwing Road Addison, Illinois 60101 USA Phone 630- 627-6900Fax 630- 627-1130Special warning to purchaser Three years parts, two years labor, ninety days travel (Not to exceed two hours)Port-A-Scrub, one year parts, six months laborThree years parts, two years labor, ninety days travelSweepers, one year parts, one year labor, ninety days travelOne year parts, one year labor, ninety day travelOne year replacement Cord Electric Group……….Battery Operated Group…..Internal Combustion Group….Battery Chargers Replacement Parts Batteries Polypropylene Plastic Tanks Exceptions……….Exceptions……………………. ..EX 12 and EX12H, one year parts, one year labor ……………..………………………….…European Representative Andre VonkHako-Minuteman-PowerBoss PO Box 174。