船舶常用英文翻译
1.All doubling plate with rounded corners.加强板要倒圆角。
2.Tank to be NK coded and stamped for 5.6 Kg/cm-name ofmanufacturer & test data to bestamped on item A1.水泥罐需NK编码和盖章，制造商名称和检验数据应印在A1上。
3.All seams to be double butt welded except as noted. 所有裂缝要双面对接焊缝，除了注意事项。
4.Radiograph all necessary welds to obtain 100%/85% joint effeciency.5.Remove slag& all assembly attachments-grind all sharp edges.清除焊溅物和所有装配附件，磨光所有锐利边缘。
6.All welds to be smooth—remove all weld spatters. 所有焊缝都要光滑，去除所有焊缝溅污。
7.After fabricated, outside of tank shall be blasted to SA2.5.制造完后，罐的外部应用SA2.5喷砂。
8.All doubling plates are to haveФ6mm telltale holes.所有加强板要有Ф6mm 的信号孔。
词汇Access hatch 人孔Access ladder 通道竖梯AHU Air handling unit 空气处理机Air slide construction 空气气动装置Air inlet 进气孔Air compessor 空气压缩机Air lock 气闸Anchor windlass 起锚机Angle steel 角钢/角铁As per 按照，依据Ball valve 球阀Bank’s conversion table 银行的换算表Bare drum pull 150 tonnes 裸体滚筒拉力150吨Barge deck 驳船甲板Baseplate 底板Bend 弯（管）头Bend test 冷弯测试Black steel 碳钢/黑钢Blind flange 法兰堵头/盲法兰/盲板Bollard pull 系柱拉力Bostik 波士胶Bottom head 下封头Bottom plate 下封头Bow thrusters 船首推进器Bracket 托架Brake holding 200 tonnes 闸控200吨Breadth moulded 模具宽度BSP British Standard Pipe 英国标准管螺纹Butt weld 对接焊缝Cable 缆索Camlock 凸轮锁紧器/凸轮锁扣Cap plate 盖板Capstan 起锚机Captioned 标题下的Casing 套管CCS China Classification Society 中国船级社Chain block 滑轮链Chain locker 锚链舱/锚链房/链锁Check valve 止回阀Clear deck area 甲板面积Cofferdam 潜水箱Color scan 彩色扫描Commodity 货品名称Complement 补充Cone 圆锥形/圆锥体Consignment 运送，委托Controllable pitch propeller 调距螺旋桨Coupling 联结螺栓/接合螺栓Crane 起重机Crate 板条箱Custom clearance 清关Custom declearance 报关Custom declearation 报关单，海关申报表Custom clearance license holder has priority. 具有报关员证者优先考虑。
Cylinder upper part 筒体上部Cylinder lower part 筒体下部Deadweight 净吨Deck crane 甲板起重机Deck loading 甲板装载Deck machinery 甲板机械Depth moulded 模具深度Discharge 卸货孔Dished end 盘形底/蝶形封头Dispatch notice 调度通知Documents/DOC.(s) 单证Document attached 所附单证Doubling plate 加强板Draft moulded(max) 最大吃水Drain arrangement 排出装置Drill water pump 钻井水泵Drill water 钻井水Dry bulk 干散货Empty weight 总量End cover 端盖Equal tee 等径三通/正三通（等径三通就是两端直径相同，异径三通就是支管与其它两个直径不同的称为异径三通，表示方法如下：对于等径三通，比如"T3"三通则表示外径是3英寸的等径三通。
对于异径三通，比如"T4×4×3.5"表示同径为四英寸异径为3.5英寸的异径三通英文：reducing tee ）Escape hatch 安全舱口Extras 杂费Fault detection 探伤Fault detection fare 探伤费Filing 填料口Flat bar 扁钢条Fluidizing system 流化系统？Flush hatch 平舱口Flush manhole 齐平人孔FO Free Out 指船方不负担卸货费Foam 泡沫材料Foot/ Ft. 英尺Footplate 踏板/垫板Forwarder 代运人/货运公司Frame spacing 框架间距Fresh water cargo pump 货物清水泵Fuel oil cargo pump 货物燃料泵Gasket 垫圈Gasket strip 垫带Generating set 发电装置Goods declaration 货物通关Grab rail 扶手杆Grind 磨光Gross tonnage 总吨数Half coupling 半管接头Hand grab 扶手Hose 软管Hose connection 软管连接Head plate 上封头Hexagon bolt & nut( hex nut) 六角螺栓&螺母Hex head bolt 六角螺栓Hex head screw 六角螺钉Hex head plug 六角管塞HYD test 水压测试In bulk 散装Inch /In. 英寸ISPM 国际植物检疫措施标准Joint efficiency 联结率Joint efficiency headLadder 扶梯Lashing eye 固定孔Laying hooks 底钩Length between perpendicular 垂直长度чLength overall 总长Length waterline 水线长度Level indicator 水平指示器Level transmitter 液面传感器Liaise with 联络Lifting eye 吊耳Lifting plate 吊车Main engine 主发动机Messrs 收货人Mezzanine deck 夹层甲板Model 规格Mud pump 泥泵Name plate 铭牌Nipple 喷嘴Non-return valve 止回阀Non-standardly manufacture 非标准生产Notice of assignment 转让通知Nozzle centre 中心管口NPT 美国标准圆锥管螺纹量规Packages 件数Pad 加强圈Pad eye 菱形座Paint outside 外部油漆Paint inside 内部油漆Perforated ['pə:fəreit] 穿孔于穿孔Pickle 酸洗（净化作用）Pillar 柱子Pillar cap 柱盖Pilot ladder 引水梯Pipe roller 管轴Pipe support 管口支撑板Pitch circle (of Flange) (法兰)加强圈Plan view 平面图Plate 金属板Plug 堵头（管塞）Pneumatic system 气压系统/通气系统PO purchase order 订单/ postal order 邮政汇票Port of call(P.O.C) 停靠港Port of discharge (P.O.P) 卸货港Port of loading (P.O.L) 装货港Port of transfer 转运港Pressure gauge 压力计Pressure gauge seat 压力计座Pressure relief valve 减压安全阀Prestissiomo 最快捷的Principal dimension 规定尺寸Productivity（M3/H）生产率Propulsion device 推进器Propulsion system 推进系统Purge line 净化管Radiograph n 射线照片v 拍射线照片Rebate/ allowance 折扣Reducer 大小头/变径管Reducing tee 异径三通Reference standard 参考标准Relief valve 安全阀Remote pressure gauge 遥测压力表Removable chain rail 可移动链轨Retrofit project 改造项目Roller 滚轴Safety Data Sheet 安全设备数据单Screw stud 双头螺栓Screw 螺丝钉Sea chest 水手用得储物箱/通海吸水箱/海底阀箱Seam 接缝Serial number 序列号Service step 操作台Shaft driven 轴动Shark jaws 钳夹Shell 筒体Slag 炉渣，熔渣Sleeve 套筒Snatch block 开口滑轮Socket 套头接管Sound metal 优质金属Sounding pipe 测量管Specification 规格Spring washer 弹簧垫圈Stand roller shave 站辊滑轮Stern thrusters 船尾推进器Summer draught 夏季吃水Surface treatment 表面处理Switchboard Room 配电室Tankage 液舱Tee joint T型接头Telltale hole （指示孔、信号孔）警报孔Test pressure for air tightness 气密性试验Threaded hole 螺纹孔Throttle valve 节流阀THK 厚度THK BKT 。
船舶英语词汇
船舶英语词汇dugout 独木舟barge 驳船kayak （爱斯基摩人的）木排outrigger 桨叉架船rowing boat 划艇（美作：rowboat）gondola （意大利的）长平底船whale mother ship 捕鲸母船hydrofoil 水翼船catamarans 双体船dredger 挖泥船boat 船brig, brigantine 双桅船canoe 小船，独木舟caravel 快帆船cargo boat 货船coaster 近海贸易货船cod-fishing boat 捕鳕鱼船whaler 捕鲸船collier 运煤船battleship 战船shallop 小型战船coastguard cutter, coastguard vessel 巡逻艇，缉私艇revenue cutter 缉私船patrol boat 巡逻艇minelayer 布雷艇minesweeper 扫雷艇torpedo boat 鱼雷艇frigate 轻护航舰gunboat 炮舰submarine 潜水艇destroyer 驱逐舰corvette 轻巡洋舰cruiser 巡洋舰aircraft carrier 航空母舰ferry, ferryboat 渡船，渡轮fishing boat 渔船freighter 货船galleon 大型帆船galley 大划桨船hovercraft 气垫船icebreaker 破冰船launch 艇lifeboat 救生艇lighter 驳船liner, ocean liner 远洋班轮merchant ship, merchantman 商船motorboat 摩托艇outboard 尾部装有马达的小艇paddle steamer, paddle boat 明轮船passenger boat 客船piragua, pirogue 独木舟raft 木筏rowing boat 划艇sailing boat, sailing ship 帆船schooner 纵帆船ship 船skiff 小艇sloop 单桅船steamer, steamship 汽轮tanker 油轮trawler 拖网渔船tug, tugboat 拖轮vessel 船yacht 游艇yawl 船载小艇构架结构 Framed structure清洁压载舱Clean ballast tank纵桁结构 Girder structure冷凝水柜Condensate catch tank人孔 manhole干舱 Dry tank饮用水舱 Drinking water tank密封圈 Sealing ring污水舱 Bilge tank铰链 Hinge应急淡水柜Emergency fresh water tank 把手 Handle首舱 Fore tank平衡块 Balance block首尖舱 Fore peak tank斜边舱Hopper side tankwelding焊接液舱 Liquid tank坡口 groove龙骨舱 Keel tank单面坡口 Single groove右舷舱 Starboard tank双面坡口 Double groove顶边水舱 Topside tankⅠ形坡口 Square groove顶边翼舱Topside wing tankV型坡口Single v groove小舱口盖Small hatch coverU型坡口Single u groove水密舱口盖Water-tight small hatch coverX形坡口Single v groove风雨密舱口盖Weather-tight small hatch coverK形坡口 Single bevel grooveY形坡口Single v groove with broad rood face填充金属 Filler metal坡口面 Groove face热影响区 Heat-affected zone(HAZ)坡口角度 Groove angle过热区 Overheated zone焊缝倾角 Weld slope焊合线 Bond line(fusion line)接头根部 Root of joint焊接区 Weld zone根部间隙 Root gap焊缝区Weld metal area钝边 Root face焊缝 weld焊接接头 Welding joint连续焊缝 Continuous weld对接接头 Butt joint断续焊缝 Intermittent weld角接接头 Corner joint纵向焊缝 Longitudinal weldT形接头 T-joint横向焊缝 Transverse weld搭接接头 Lap joint对接焊缝隙 Butt weld十字接头Cross shaped joint角焊缝 Filled weld母材 Base metal(parent metal)并列断续角焊缝Chain intermittent fillet交错断续角焊缝Staggered intermittent fillet弧焊整流器 Arc welding rectifier焊缝正面 Face of weld自动焊 Automatic welding焊缝背面 Back of weld埋弧自动焊Submerged arc welding焊缝宽度 Weld width半自动焊Semi- automatic welding焊缝长度 Weld length氩弧焊 Argon-arc welding焊缝余高 Reinforcement二氧化碳气体保护焊CO2 gas shielded arc welding 焊脚Leg(of a fillet weld)氧乙炔焊 Oxy-acetylene welding焊脚长度 Leg length气割 Gas cutting套管接头 Muff joint碳弧气刨Carbon arc air gouging手工电弧焊Manual arc welding(shielded metal arc welding)水下切割 Underwater cutting直流电弧焊Direct current arc welding等离子弧切割Plasma arc cutting交流电弧焊alternating current arc welding连续焊 Continuous welding弧焊变压器 Arc welding transformer断续焊 Intermittent welding点焊 Sport welding对接焊 Butt welding分段退焊Back step welding角焊 Fillet welding分段多层焊 Block welding搭接焊 Lap welding深溶焊 Deep penetrating welding返修焊 Re-welding跳焊 Skip welding补焊 Repair welding陶质衬垫焊Ceramic backing welding定位焊 Tack welding引弧 Striking the arc封底焊Back sealing welding焊接工艺参数 Welding condition打底焊 Backing welding焊接电流 Welding current堆焊 Surfacing(overlaying)焊接电压 Welding voltage塞焊 Plug welding焊接速度 Welding speed槽焊 Slot welding电弧电压 Arc voltage盖面焊 Consmetic welding焊丝间距 Wire spacing前倾焊 Forward welding空载电压Open circuit voltage后倾焊 Backward welding熔化速度 Melting rate41． 300吨，是船台用起重机，跨度72m。
船舶常用英语
1、HULL PART 船体部分1、1结构 Structure1 2船厂 dockyard/shipyard 船坞 dock/boatyard船东 ship-owner 船舷 Ship's side船码头 quay/dock 船的栏杆 Ship's rail船舱 hold 甲板 Deck船籍 Ship's registry 住舱甲板 accommodation deck 船首 bow 梁拱甲板 arch deck船梯 ladder 载货甲板 cargo deck船尾 stern 首楼甲板 Forecastle deck上甲板 Upper deck下甲板 Lower deck主甲板 Main deck货舱甲板 Hold deck桥楼甲板 Bridge deck水密甲板 Watertight deck3 4驾驶甲板 Navigation deck 铜-钢复合板 Copper sheathing steel plate艇甲板 Boat deck 甲板边板 Deck stringer plate罗经甲板 Compass deck 斜板 Sloping plate板 Plate 加强板 Reinforcement plate舭板 Bilge plate 舵板 Rudder plate船底板 Bottom plate 舷侧外板 Side plate船外板 Shell plate 裙板 Skirt plate船首外板 Bow plate 首柱板 Stem plate肘板 Bracket plate 尾柱板 Stern plate舱壁板 Bulkhead plate 平台 Platform槽形舱壁板 Corrugated bulkhead plate 机舱平台 Engine-room platform舷墙板 Bulwark plate 分段 Block围板 Coaming plate 首段 Bow block连续板 Connection plate 中段 Midship block5 6尾段 Stern block 甲板下纵桁 Underdeck girder左舷 port 舭纵桁 Wing girder右舷 Starboard 支柱 Pillar纵桁 Girder 肋骨 Frame型材桁 Bar girder 基础台架 Base frame中底桁 Bottom center girder 支架 Bear frame中内龙骨 Bottom center line girder 舭肋骨 Bilge frame底桁材 Bottom girder 船底肋骨 Bottom frame旁桁材 Bottom side girder 首肋骨 Bow frame甲板纵桁 Deck girder 肘板框架肋骨 Bracket frame 横桁 Cross girder 球鼻首肋骨 Bulbous bow frame 水平桁 Horizontal girder 球曲型肋骨 Bulbous frame 舱口边梁 Hatch coaming girder 主肋骨 Chief frame 机座纵桁 Engine girder 首肋骨 Fore frame7桁架梁 Girder frame 舭纵桁舭纵骨 Bilge longitudinal舯部肋骨 Middle frame 船底纵骨/纵桁 bottom longitudinal尖舱肋骨 Peak frame 船底腹板纵桁 Bottom web longitudinal加强筋 Stiffened frame 甲板纵桁 Deck longitudinal 横框架肋骨 Transverse frame 内底纵桁/纵骨 Inner bottom longitudinal肋距 F.S.(frame space) 舷侧纵桁/纵骨 Shell side longitudinal纵桁/纵骨/纵向构件 longitudinal 双层底顶纵骨 Top longitudinal of double bottom8 9斜舱壁纵骨 Slopping-bulkhead longitudinal 舱 Tank结构 Structure 尾尖舱 after peak tank附属结构 Accessory structure 尾部水舱 after water tank全焊结构 All-welded structure 辅助水柜 Auxiliary water tank中部结构 Amidships structure 辅助压载水舱 Auxiliary water ballast tank泊位结构 Berthing structure 污水舱 Bilge tank底部龙骨结构 Bottom keel structure 底舱 Bottom tank船首部结构 Bow structure 底边舱 Bottom side tank 支撑结构 Braced structure 货油压载舱 Cargo and ballast tank桥楼结构 Bridge structure 循环水槽 Circulating flow water tank首楼结构 Forecastle structure 循环滑油舱 Circulating lubricating oil tank构架结构 Framed structure 清洁压载舱 Clean ballast tank纵桁结构 Girder structure 冷凝水柜 Condensate catch tank人孔 manhole 干舱 Dry tank10 11饮用水舱 Drinking water tank 密封圈 Sealing ring 污水舱 Bilge tank 铰链 Hinge应急淡水柜 Emergency fresh water tank 把手 Handle 首舱 Fore tank 平衡块 Balance block首尖舱 Fore peak tank斜边舱 Hopper side tank 1、2 welding焊接液舱 Liquid tank 坡口 Groove龙骨舱 Keel tank 单面坡口 Single groove右舷舱 Starboard tank 双面坡口 Double groove顶边水舱 Topside tank Ⅰ形坡口 Square groove顶边翼舱 Topside wing tank V型坡口 Single v groove小舱口盖 Small hatch cover U型坡口 Single u groove水密舱口盖 Water-tight small hatch cover X形坡口 Single v groove风雨密舱口盖 Weather-tight small hatch cover K形坡口 Single bevel groove12 13Y形坡口 Single v groove with broad rood face 填充金属 Filler metal坡口面 Groove face 热影响区 Heat-affected zone(HAZ)坡口角度 Groove angle 过热区 Overheated zone焊缝倾角 Weld slope 焊合线 Bond line(fusion line) 接头根部 Root of joint 焊接区 Weld zone根部间隙 Root gap 焊缝区 Weld metal area钝边 Root face 焊缝 weld焊接接头 Welding joint 连续焊缝 Continuous weld 对接接头 Butt joint 断续焊缝 Intermittent weld 角接接头 Corner joint 纵向焊缝 Longitudinal weld T形接头 T-joint 横向焊缝 Transverse weld搭接接头 Lap joint 对接焊缝隙 Butt weld十字接头 Cross shaped joint 角焊缝 Filled weld 母材 Base metal(parent metal) 并列断续角焊缝 Chain intermittent fillet14 15交错断续角焊缝 Staggered intermittent fillet 弧焊整流器 Arc welding rectifier焊缝正面 Face of weld 自动焊 Automatic welding 焊缝背面 Back of weld 埋弧自动焊 Submerged arc焊缝宽度 Weld width 半自动焊 Semi- automatic welding焊缝长度 Weld length 氩弧焊 Argon-arc welding焊缝余高 Reinforcement 二氧化碳气体保护焊 CO2 gas shielded arc welding焊脚 Leg(of a fillet weld) 氧乙炔焊 Oxy-acetylene welding焊脚长度 Leg length 气割 Gas cutting套管接头 Muff joint 碳弧气刨 Carbon arc air gouging手工电弧焊 Manual arc welding(shielded metal arc welding) 水下切割 Underwater cutting直流电弧焊 Direct current arc welding 等离子弧切割 Plasma arc cutting交流电弧焊 alternating current arc welding 连续焊 Continuous welding弧焊变压器 Arc welding transformer 断续焊 Intermittent welding点焊 Sport welding16 17对接焊 Butt welding 分段退焊 Back step welding 角焊 Fillet welding 分段多层焊 Block welding搭接焊 Lap welding 深溶焊 Deep penetrating welding返修焊 Re-welding 跳焊 Skip welding补焊 Repair welding 陶质衬垫焊 Ceramic backing welding定位焊 Tack welding 引弧 Striking the arc封底焊 Back sealing welding 焊接工艺参数 Welding condition打底焊 Backing welding 焊接电流 Welding current 堆焊 Surfacing(overlaying) 焊接电压 Welding voltage塞焊 Plug welding 焊接速度 Welding speed槽焊 Slot welding 电弧电压 Arc voltage盖面焊 Consmetic welding 焊丝间距 Wire spacing 前倾焊 Forward welding 空载电压 Open circuit voltage后倾焊 Backward welding 熔化速度 Melting rate18 19送丝速度 Wire feed rate 层间温度 Inter-pass temperature气体流量 Gas flow rate 焊后热处理 Post-weld heat焊丝伸出长度 Wire extension 锤击 Peening极性 Polarity 全焊透 Full penetration welding正极/阳极 Positive electrode 熔池 Weld-pool负极/阴极 Navigate electrode 熔深 Penetration左焊法 Leftward welding 弧长 Arc length右焊法 Rightward welding 喷射过渡 Spray transfer 电流密度 Current density 短路过渡 Short circuiting transfer线能量 Heat input 熔滴过渡 Metal transfer预热 Preheat 焊缝成形 Appearance of weld后热 Post-heat 焊缝成形系数 Form factor of weld 预热温度 Preheat temperature 熔敷系数 Deposition coeffcient后热温度 Post-heat temperature 熔敷效率 Deposition efficiency20 21熔合比 Penetration ratio 立焊 Vertical position welding等速送丝 Constant wire-feed system 仰焊 Overhead position welding变速送丝 alternate wire-feed system 立向上焊 Vertical up welding电弧静特性 Static characteristic of arc 立向下焊 Vertical down welding电弧动特性 dynamic characteristic of arc 单面焊 Welding by one side焊接性试验 Weldability test 双面焊 Welding by both side焊接结构 Welded construction 单道焊 Single-pass welding焊道 Bead 多道焊 Multi-pass welding焊层 Layer 多层焊 Multi-layer welding正接（正极性） Straight polarity 焊接材料 Consumables反接（反极性） Reversed polarity 焊条 Electrode 焊接位置 Position of welding 焊条药皮 Coating平焊 Flat position welding 酸性焊条 Acid electrode横焊 Horizontal position welding 碱性焊条 Basic electrode22 23低氢型焊条 Low hydrogen type electrode 焊丝盘 Wire reel铁粉性焊条 Iron power type electrode 铜冷却板 Cu-cooling plate重力焊条 Gravity electrode 铜滑块 Copper shoe焊剂 Flux 切割 Cutting熔炼焊剂 Fused flux 焊接工作台 Welding bench烧结焊剂 Sintered flux 焊接变位机 Positioner焊丝 Wire 送丝机构 Wire feeder药芯焊剂 Flux-cored wire 行走机构 Traveler保护气体 Shielded gas 焊接车间 Welding shop焊剂垫 Flux backing 引弧板 Run-on tab(end tab) 重力焊条 Gravity electrode 引出板 Run-off tab(end tab)焊剂漏斗 Flux-hopper 定位板 Strong-back流量计 Flow meter 焊接衬垫 Welding backing干燥箱 Dryer 敲渣锤 Chipping hammer24 25面罩 Helmet 条虫状气孔 Wormhole焊工手套 Welding glove 密集气孔 Porosity焊钳 Electrode holder 针尖状气孔 Pinhole焊枪 Welding gun 白点 Fish eye (flake)导电嘴 Tip 切口 Kerf喷嘴 Nozzle 咬边 Undercut焊矩 Torch 焊瘤 overlap焊接缺陷 Welding defect 凹坑 Pit未焊透 Incomplete penetration 烧穿 Burn through 未熔合 Incomplete fusion 未满焊 Incomplete filled groove渣 Slag 清根 Back chipping夹渣 Slag (slag inclusion) 清渣 Slag removal夹杂物 Inclusion 焊接烟尘 Weld fume气孔 Blow hole 电光性眼炎 Eye-flash26 27焊接性 Weldability 横裂纹 Transverse crack碳当量 Carbon equivalent 纵裂纹 Longitudinal crack未焊满 Incomplete filled groove 焊趾裂纹 Toe crack焊接裂纹 Weld crack 机械性能试验 Mechanical property test热裂纹 Hot crack 试板 Test piece冷裂纹 Cold crack 试样 Specimen氢致裂纹 Hydrogen –induced crack 侧弯 Side bend 延迟裂纹 Delayed crack 弯曲 Bending层状撕裂 Lemellar tearing 横向拉伸 Transversetensile弧坑裂纹 Crater crack 宏观试样 Macro-etching specimen根部裂纹 Root crack 微观试样 Micro-examination specimen再热裂纹 Reheat crack 破断试验 Fracture test热影响区裂纹 Heat-effected zone crack 抗裂试验 Cracking test晶间裂纹 Intercystalline crack 脆性断裂 Brittle fracture28 29塑性断裂 Plastic fracture 焊接方法 Welding process焊接残余裂纹 Welding residual stress 焊接工艺 Welding technology消除应力 Stress relieving 焊接操作 Welding operation焊接变形 Welding deformation 焊接顺序 Welding sequence角变形 Angular distortion 焊接方向 Direction of welding外观检查 Visual examination 常用缩语无损探伤 Non-destruction testing(N.D.T.) 气电立焊 EGW超声波探伤 Ultrasonic inspection 药芯电弧焊 FCAW 射线探伤（X光） Radiographic inspection(X-ray inspection) 实心电弧焊 GMAW磁粉探险伤 Magnetic particle inspection 焊剂铜衬垫单面埋弧自动焊 FCB渗透探伤 Penetrate inspection 手工电弧焊 SMAW熔池 Weld-pool 埋弧自动焊 SAW焊机（焊接电源） Weld source30 31钨极惰性气体保护电弧焊 TIG 机舱部分 ENGINE ROOM PART 熔化极惰性气体保护焊 MIG 一、机舱设备 Machines and equipment in engine room活性气体保护焊 MAG 1、主机 Main engine手工电弧切割 SMAC 1）主机油底壳 The sump tank of M.E.2）主机飞轮 Fly wheel of M.E3）活塞 Piston2、发电机 Generator engine1）应急发电机 Emergency generator engine2）辅机 Auxiliary3、锅炉 Boiler1）组合锅炉 The composite boiler2）锅炉安全阀 The safety valve of boiler32 343）燃烧器 Oil burner unit 3）主空气瓶 Main air reservoir4）水位表 Water level gauge 4）应急空气瓶 Emergency air reservoir5）水位控制器 Water level controller 5、控制空气瓶 Control air reservoir6）过量蒸气调节阀 Excess steam pressure control valve 6、空气干燥器 Air dryer4、舵机 7、分油机 Oil purifier1）舵机间 Steering room 1）燃油分油机 Fuel oil purifier2）舵机装置 Steering-gear 2）柴油分油机 Diesel oil purifier3）手操舵装置 Trick wheel plant 3）滑油分油机 Lubricate oil purifier4）油缸 Oil cylinder 4）排渣 Sludge discharge 5）反馈装置 Feedback device 8、制淡装置 Fresh water generator6）舵 Rudder 9、焚烧炉 Incinerator舵叶 Rudder blade 10、油水分离器 Oil water separator舵杆 Rudder stock 11、生活污水处理器 Sewage treat plant上舵承 Rudder carrier 12、大气冷凝器 Atmosphere condenser35 36热水井 Cascade and inspection(hot well) 5）主机燃油供给泵 Main engine fuel oil supply pump滑油自清滤器 The automatic back-flash lubricating oil filter 6）主机燃油增压泵 Main engine fuel oil booster pump 燃油单元 Fuel oil unit 7）主机十字头泵 Main engine cross head pump1）主机燃油单元 Fuel oil unit of M.E 8）付机海水泵 Generator engine sea water pump2）付机燃油单元 Fuel oil unit of A.E 9）付机缸套水泵 Generator engine cylinder cooling water pump3）粘度计 Viscosity controller 10）锅炉给水泵 Feed water pump of boiler泵 Pump 11）锅炉燃油泵 Fuel oil pump of boiler 1）主机滑油泵 Main engine lubricating oil pump 12）分油机供给泵 Fuel oil supply pump of purifier2）主机缸套水泵 Main engine cylinder cooling water pump 13）制淡海水泵 Sea water pump of fresh water generator3）主机缸套水预热泵 Main engine cylinder cooling water preheating pump 14）压载泵 Ballast pump4）主机海水泵 Main engine sea water pump 15）舱底消防泵 Bilge and fire pump37 3817）油渣泵 Sludge oil pump 2、柴油澄清舱 Diesel oil setting tank18）柴油输送泵 Diesel oil transport pump 3、燃油日用柜 Fuel oil daily tank19）燃油油输送泵 Fuel oil transport pump 4、燃油澄清舱 Fuel oil setting tank20）汽缸油输送泵 Cylinder oil transport pump 5、滑油澄清舱 Lubricating oil setting tank21）淡水输送泵 Fresh water transport pump 6、滑油储藏舱 Lubricating oil store tank22）热水循环泵 Hot water circulating pump 7、滑油循环舱 Lubricating oil circulating tank23）饮水日用泵 Drinking water pump 8、燃油溢油舱 Fuel oil overflow tank舱底消防总用泵 Bilge, fire and G.S pump 9、燃油油渣舱 Fuel oil sludge tank喷淋泵 Sprinkling pump 10燃油深舱 Fuel oil deep tank停泊海水泵 Harbor sea water pump 11滑油污油舱 Lubricating dirty oil tank12滑油溢油舱 Lubricating oil overflow tank 二、各种舱（箱）柜 All kinds of tank 13滑油油渣打舱 Lubricating oil sludge tank1、柴油日用柜 Diesel oil daily tank 14主机淡水膨胀水箱 M.E fresh water expansion tank15付机淡水膨胀水箱 A.E fresh water expansion tank39 4016、淡水压力柜 Fresh water pressure tank 1、滑油系统 Lubricating oil piping system17、热水压力柜 Hot water pressure tank 2、燃油系统 Fuel oil piping system18、饮水压力柜 Drinking water pressure tank 3、海水系统 Sea water piping system19、淡水舱 Fresh water tank 4、缸套水系统 Cylindercooling water piping system20、饮水舱 Drinking water tank 5、启动空气系统 Start air piping system21、锅炉水舱 Boiler water tank 6、控制空气系统 Control air piping system22、分油机工作水箱 Purify operating water tank 7、排气系统 Exhaust piping system23、汽缸油日用柜 Cylinder oil daily tank 8、日用供水系统 Daily water piping system24、尾管滑油重力柜 Gravity tank of tube oil 9、蒸汽系统 Steam piping system25、排气水封箱 Exhaust seal water tank 10 、锅炉给水和凝水系统 Feed water and condensate of boiler piping system 26、蒸馏水水舱 Distilling water tank 11、燃油净油系统 Fuel oil purified piping system27、污水井 Bilge well 12、燃油输送系统 Fuel oil transport piping system三、各种管系系统 All kinds of pipes33 41舵销 Rudder pintle 13、滑油净油系统 Lubricating oil purified piping system舵杆衬套 rudder stock liner 14、滑油输送系统 Lubricating oil transport piping system舵杆轴套 Sleeve for rudder stock 15、舱底压载系统 Ballast and bilge water piping system舵销承衬套 Bush for rudder pintle 四、仪表类 Instructions舵销轴套 Sleeve for rudder pintle 1、压力表 Pressure gauge上舵承底座 Rudder carrier seat 2、真空表 Vacuum gauge舵销承座 Pintle bearing 3、温度计 Thermometer舵杆承座 Rudder stock bearing 4、吨位表 DWT gauge 挡圈 Retaining ring 5、遥测表 Distant survey gauge舵柄 Tiller 6、液全器 Level switch7）舵角 The angle of rudder5、空压机 Air compressor1）主空压机 Emergency air compressor2）应急空压机42 437、传感器 Sensor 12、机控室 Engine control room五、其它 Others 13、台虎钳 Vise (=vice)1、风机 Fan 14、表铜截止阀 Bronze close valve2、防海生物装置 Anti-foul STM plant 15、表铜截止止回阀 Bronze check valve3、泡沫柜 Air foam tank 16、铸铁截止阀 Cast iron stop valve4、中间轴 Middle shaft 17、铸铁截止止回阀 Cast iron check and stop valve5、尾轴 Propeller shaft 18、调节阀 Adjustable valve6、螺旋桨 Propeller 19、溢流阀、安全阀 Relief valve7、中间轴承 Line shaft bearing 20、减压阀 Reducing valve8、泡沫灭火机 Foam fire extinguisher 六、材料 Material9、饮水消毒装置 Sterilizer plant 1、管子 Pipe10、主配电板 Main switch board 2、无缝钢管 Seamless steel pipe (tube)11、机舱集控台 Engine room control console 3、紫铜管 Purple copper pipe44 454、铁法兰 Iron flange 18、支架（马脚） Clamp5、铜法兰 Copper flange 19、油漆 Paint6、盲板法兰 Blind-flange 20、备件 Spare parts7、螺丝（螺栓） Bolt8、双头螺丝 Stud 七、生产工具 Produce tool9、螺帽（螺母） Nut 1、图纸 Drawing10、不锈钢螺丝 Stainless steel bolt 2、活络钣 Adjustable spanner11、垫片（床） Gasket 3、令司板（梅花钣） Ring spanner12、橡皮床 Gum gasket 4、开口钣 Open –ender spanner13、纸箔床 Paper copper gasket 5、管子钳 Pipe wrench14、紫铜床 Purple copper gasket 6、凿子 Chisel15、石墨床 Black lead gasket 7、锒头 Hammer16、青铅床 Black lead gasket 8、锉刀 File17、佛纳 Feeler gauge 9、螺丝刀 Screwdriver46 4710、油漆滚筒 Paint roller 4、首先请检查安装说明和电气绝缘11、油漆刷子 Paint brush Please check the condition of installation and insulation first12、钢锯 Hacksaw 5、我们准备将油水分离器动转13、套筒扳手 Socket spanner Now we will run the oily-water separator14、手电筒 Torch 6、请检查动转情况15、钻头 driller Please check the running condition八、英语会话 7、接着我们一个一个地做报警/安全保护装置的功能试验1、早上好 good morning Now we will do the function test about alarm and safety device2、今天我们准备交验油水分离器 8、设备交接基本结束Today we will test the oily-water separator. Now the test is over 3、请跟我来 9、请部有何修改意见？Please fellow me. Do you have any question ?48 4910、非常感谢 17、这里增加一只落水斗Thanks Add a drain plug here11、再见 18、请用空气压缩空气吹干Good bye Please dry it by the compressed air12、请把这对法兰撬紧松开 19、我将回车间支拿肥皂水Please tighten/release the flange I will com to my workshop to take some soap water13、这路管子是从发电机单元来的 20、这个系统非常重要的，一定要认真检查The piping is from to the G/E unit This system is very important ,please check it carefully14、这对法兰/接头在漏 21、请交验收整改意见This flange /connection is linking Please check your remarks 15、这路系统的试验压力是7公斤 22、天太热了，请休息一会The test pressure of the piping system is 7 bar It’s too hot ,please take a rest16、这里请加强 please make a clamp here 23、我负责这项工作 I am in charge of this job。
船舶英语词汇
船舶专用词汇1.船舶的分类passenger ship 客船general cargo ship 杂货船bulk cargo carrier 散货船container ship 集装箱船roll on/roll off ship 滚装船tanker 油船liquid gas carrier 液化气船barge 驳船barge carrier 载驳船dredger 挖泥船floating crane 起重船floating dock 浮船坞ice breaker 破冰船drilling platform 钻井平台drilling ship 钻井船trawler 拖网渔船stern ramp trawler 尾滑道拖网渔船tug boat 拖船fire boat 消防船ocean survey ship 海洋调查船cruiser 巡洋舰destroyer 驱逐舰frigate 护卫舰aircraft carrier 航空母舰submarine 潜艇hydrofoil craft 水翼艇air cushion vehicle 气垫船—hovercraft 全浮式气垫船—sidewall air cushion vehicle 侧壁式气垫船small waterplane area twin hull ship 小水线面双体船semi-submerged catamaran 又称为半潜双体船2.船体结构longitudinal bending 总纵弯曲hogging 中拱弯曲sagging 中垂弯曲longitudinal strength 总纵强度transverse strength 横向强度local strength 局部强度hull 船体superstructure 上层建筑stem 船首midship 船中stern 船尾forecastle 艏楼bridge 桥楼poop 艉楼deck house 甲板室ship bottom 船底ship side 舷侧upper deck 上甲板lower deck 下甲板transverse bulkhead 横舱壁longitudinal bulkhead 纵舱壁fore peak bulkhead 艏尖舱舱壁after peak bulkhead 艉尖舱舱壁3.外板和甲板板shell plate 外板seam 边接缝butt 端接缝strake 列板bottom plate 船底板plate keel 平板龙骨bilge strake 舭列板side plate 舷侧外板sheer strake 舷顶列板upper deck 上甲板second deck 第二甲板third deck 第三甲板platform deck 平台甲板deck plate 甲板板deck stringer 甲板边板sponson deck 舷伸甲板4.船底结构center keelson 中内龙骨side keelson 旁内龙骨T-bar T型材web 腹板bracket 肘板face plate 面板flange 钢板折边法兰bilge bracket 舭肘板floor 肋板solid floor 主肋板watertight floor 水密肋板bracket floor 框架肋板lightened floor 轻型肋板stiffener 加强筋扶强材bulb plate 球扁钢angle bar 不等边角钢bottom center girder 中底桁bottom center girder 旁底桁duct keel 箱形中底桁pipe tunnel 管隧reverse frame 内底横骨bottom frame 船底肋骨longitudinal 纵骨bottom longitudinal 船底纵骨inner bottom longitudinal 内底纵骨inner bottom plate 内底板margin plate 内底边板man hole 人孔bilge well 污水井bottom side tank 底边舱foundation seating 基座shaft tunnel 轴隧tunnel recess 艉室emergency exit 应急通道bilge keel 舭龙骨5.舷侧结构Integrated barge 分节驳frame 肋骨main frame 主肋骨tweendeck frame 甲板间肋骨intermediate frame 中间肋骨web frame 强肋骨side longitudinal 舷侧纵骨cross tie 撑杆wing tank 舷边舱ballast water tank 压载水舱torsion box 抗扭箱bulwark 舷墙fender 护舷材6.甲板结构beam 横梁deck beam 普通横梁hatch end beam 舱口端横梁deck girder 甲板纵桁side stringer 舷侧纵桁hatch side girder 舱口纵桁beam knee 梁肘板sponson deck 舷伸甲板deck longitudinal 甲板纵骨web beam 强横梁cargo hatch 货舱口hatch coaming 舱口围板gusset plate 菱形板hatch side cantilever 悬臂梁pillar 支柱topside tank 顶边舱excess hatch 出入舱口expansion trunk 膨胀井7.舱壁结构bulkhead 舱壁cofferdam 隔离空舱partial bulkhead 局部舱壁plane bulkhead 平面舱壁bulkhead plate 舱壁板tweendeck bulkhead 甲板间舱壁vertical stiffener 垂直扶强材8.首尾端结构vertical bow 直立型艏raked bow 前倾型艏clipper bow 飞剪型艏ice breaker bow 破冰型艏elliptical stern 椭圆形艉cruiser stern 巡洋舰型艉transom stern 方形艉fore peak艏尖舱collision bulkhead 防撞舱壁raised floor 升高肋板panting beam 强胸横梁wash bulkhead 制荡舱壁chain locker 锚链舱breast hook 艏肘板stem 艏柱steel plate stem 钢板艏柱forged steel stem 锻钢艏柱combination cast and rolled stem 混合式艏柱tunnel 管隧thruster 侧推器after peak 艉尖舱shaft tube 艉轴管cant frame 斜肋骨cant beam 斜横梁stern frame 艉柱shoe piece 艉柱底骨rudder post 舵柱propeller post 螺旋桨柱propeller shaft strut 艉轴架A-bracket 人字架shell bossing 轴包套spectacle frame 眼镜形骨架9.上层建筑和机舱棚结构accommodation 起居甲板boat deck 艇甲板navigation deck 驾驶甲板compass deck 罗经甲板compass platform 罗经平台expansion joint 伸缩接头derrick post桅杆derrick platform 起货机平台tower post 塔式桅stern door 艉门bow door 艏门visor type 罩壳式side hinged type 边铰链式pressure structure 耐压结构non pressure structure 非耐压结构pressure conning tower 耐压指挥台pressure tank 耐压水舱pressure bulkhead 耐压舱壁oil ballast tank 燃油压载水舱ballast water tank 压载水舱conning tower sail 指挥台围壳渔业船舶种类2.1 渔船fishing vessel 用于商业性捕捉鱼类、鲸、海豹、海象或其他生物资源的船舶之统称。
船舶英语词汇
船舶英语词汇2009-03-02 14:00:36| 分类：船务| 标签：无|字号大中小订阅1、HULL PART 船体部分1、1 结构Structure船厂dockyard/shipyard 船坞dock/boatyard船东ship-owner 船舷Ship's side船码头quay/dock 船的栏杆Ship's rail船舱hold 甲板Deck船籍Ship's registry 住舱甲板accommodation deck船首bow 梁拱甲板arch deck船梯ladder 载货甲板cargo deck船尾stern 首楼甲板Forecastle deck上甲板Upper deck下甲板Lower deck主甲板Main deck货舱甲板Hold deck桥楼甲板Bridge deck水密甲板Watertight deck驾驶甲板Navigation deck 铜-钢复合板Copper sheathing steel plate艇甲板Boat deck 甲板边板Deck stringer plate罗经甲板Compass deck 斜板Sloping plate板Plate 加强板Reinforcement plate舭板Bilge plate 舵板Rudder plate船底板Bottom plate 舷侧外板Side plate船外板Shell plate 裙板Skirt plate船首外板Bow plate 首柱板Stem plate肘板Bracket plate 首柱板Stern plate舱壁板Bulkhead plate 平台platform槽形舱壁板Corrugated bulkhead plate 机舱平台Engine-room platform 舷墙板Bulwark plate 分段Block围板Coaming plate 首段Bow block连续板Connection plate 中段Midship block尾段Stern block 甲板下纵桁Underdeck girder左舷port 舭纵桁Wing girder右舷Starboard 支柱Pillar纵桁Girder 肋骨Frame型材桁Bar girder 基础台架Base frame中底桁Bottom center girder 支架Bear frame中内龙骨Bottom center line girder 舭肋骨Bilge frame底桁材Bottom girder 船底肋骨Bottom frame旁桁材Bottom side girder 首肋骨Bow frame甲板纵桁Deck girder 肘板框架肋骨Bracket frame横桁Cross girder 球鼻首肋骨Bulbous bow frame水平桁Horizontal girder 球曲型肋骨Bulbous frame舱口边梁Hatch coaming girder 主肋骨Chief frame机座纵桁Engine girder 首肋骨Fore frame桁架梁Girder frame 舭纵桁舭纵骨Bilge longitudinal舯部肋骨Middle frame 船底纵骨/纵桁bottom longitudinal尖舱肋骨Peak frame 船底腹板纵桁bottom web longitudinal加强筋Stiffened frame 甲板纵桁Deck longitudinal横框架肋骨Transverse frame 内底纵桁/纵骨Inner bottom longitudinal 肋距 F.S.(frame space) 舷侧纵桁/纵骨Shell side longitudinal纵桁/纵骨/纵向构件longitudinal双层底顶纵骨Top longitudinal of double bottom斜舱壁纵骨Slopping-bulkhead longitudinal舱舷边舱Tank Wing tank结构structure 尾尖舱after peak tank附属结构Accessory structure 尾部水舱after water tank全焊结构All-welded structure 辅助水柜Auxiliary water tank中部结构Amidships structure 辅助压载水舱Auxiliary water ballast tank 泊位结构Berthing structure 污水舱Bilge tank底部龙骨结构Bottom keel structure 底舱Bottom tank船首部结构Bow structure 底边舱Bottom side tank支撑结构Braced structure 货油压载舱Cargo and ballast tank桥楼结构Bridge structure 循环水槽Circulating flow water tank首楼结构Forecastle structure 循环滑油舱压载水舱Circulating lubricating oil tank Ballast water tank构架结构Framed structure 清洁压载舱Clean ballast tank纵桁结构Girder structure 冷凝水柜Condensate catch tank人孔manhole 干舱Dry tank饮用水舱Drinking water tank 密封圈Sealing ring污水舱Bilge tank 铰链Hinge应急淡水柜Emergency fresh water tank 把手Handle首舱Fore tank 平衡块Balance block首尖舱Fore peak tank斜边舱Hopper side tank 1、2 welding 焊接液舱Liquid tank 坡口groove龙骨舱Keel tank 单面坡口Single groove右舷舱Starboard tank 双面坡口Double groove顶边水舱Topside tank Ⅰ形坡口Square groove顶边翼舱Topside wing tank V 型坡口Single v groove小舱口盖Small hatch cover U 型坡口Single u groove水密舱口盖Water-tight small hatch coverX 形坡口Single v groove风雨密舱口盖Weather-tight small hatch coverK 形坡口Single bevel grooveY 形坡口Single v groove with broad rood face填充金属Filler metal坡口面Groove face 热影响区Heat-affected zone(HAZ)坡口角度Groove angle 过热区Overheated zone焊缝倾角Weld slope 焊合线Bond line(fusion line)接头根部Root of joint 焊接区Weld zone根部间隙Root gap 焊缝区Weld metal area钝边Root face 焊缝weld焊接接头Welding joint 连续焊缝Continuous weld对接接头Butt joint 断续焊缝Intermittent weld角接接头Corner joint 纵向焊缝Longitudinal weldT 形接头T-joint 横向焊缝Transverse weld搭接接头Lap joint 对接焊缝隙Butt weld十字接头Cross shaped joint 角焊缝Filled weld母材Base metal(parent metal) 并列断续角焊缝Chain intermittent fillet交错断续角焊缝Staggered intermittent fillet弧焊整流器Arc welding rectifier焊缝正面Face of weld 自动焊Automatic welding焊缝背面Back of weld 埋弧自动焊Submerged arc welding焊缝宽度Weld width 半自动焊Semi- automatic welding焊缝长度Weld length 氩弧焊Argon-arc welding焊缝余高Reinforcement 二氧化碳气体保护焊CO2 gas shielded arc welding 焊脚Leg(of a fillet weld) 氧乙炔焊Oxy-acetylene welding焊脚长度Leg length 气割Gas cutting套管接头Muff joint 碳弧气刨Carbon arc air gouging手工电弧焊Manual arc welding(shielded metal arc welding)水下切割Underwater cutting直流电弧焊Direct current arc welding 等离子弧切割Plasma arc cutting交流电弧焊alternating current arc welding连续焊Continuous welding弧焊变压器Arc welding transformer 断续焊Intermittent welding点焊Sport welding对接焊Butt welding 分段退焊Back step welding角焊Fillet welding 分段多层焊Block welding搭接焊Lap welding 深溶焊Deep penetrating welding返修焊Re-welding 跳焊Skip welding补焊Repair welding 陶质衬垫焊Ceramic backing welding定位焊Tack welding 引弧Striking the arc封底焊Back sealing welding 焊接工艺参数Welding condition打底焊Backing welding 焊接电流Welding current堆焊Surfacing(overlaying) 焊接电压Welding voltage塞焊Plug welding 焊接速度Welding speed槽焊Slot welding 电弧电压Arc voltage盖面焊Consmetic welding 焊丝间距Wire spacing前倾焊Forward welding 空载电压Open circuit voltage后倾焊Backward welding 熔化速度Melting rate送丝速度Wire feed rate 层间温度Inter-pass temperature气体流量Gas flow rate 焊后热处理Post-weld heat treatment焊丝伸出长度Wire extension 锤击Peening极性Polarity 全焊透Full penetration welding正极/阳极Positive electrode 熔池Weld-pool负极/阴极Navigate electrode 熔深Penetration左焊法Leftward welding 弧长Arc length右焊法Rightward welding 喷射过渡Spray transfer电流密度Current density 短路过渡Short circuiting transfer线能量Heat input 熔滴过渡Metal transfer预热Preheat 焊缝成形Appearance of weld后热Post-heat 焊缝成形系数Form factor of weld预热温度Preheat temperature 熔敷系数Deposition coeffcient后热温度Post-heat temperature 熔敷效率Deposition efficiency熔合比Penetration ratio 立焊Vertical position welding等速送丝Constant wire-feed system 仰焊Overhead position welding 变速送丝alternate wire-feed system 立向上焊Vertical up welding电弧静特性Static characteristic of arc立向下焊Vertical down welding电弧动特性dynamic characteristic of arc单面焊Welding by one side焊接性试验Weldability test 双面焊Welding by both side焊接结构Welded construction 单道焊Single-pass welding焊道Bead 多道焊Multi-pass welding焊层Layer 多层焊Multi-layer welding正接（正极性）Straight polarity 焊接材料Consumables反接（反极性）Reversed polarity 焊条Electrode焊接位置Position of welding 焊条药皮Coating平焊Flat position welding 酸性焊条Acid electrode横焊Horizontal position welding 碱性焊条Basic electrode低氢型焊条Low hydrogen type electrode 焊丝盘Wire reel铁粉性焊条Iron power type electrode 铜冷却板Cu-cooling plate重力焊条Gravity electrode 铜滑块Copper shoe焊剂Flux 切割Cutting熔炼焊剂Fused flux 焊接工作台Welding bench烧结焊剂Sintered flux 焊接变位机Positioner焊丝Wire 送丝机构Wire feeder药芯焊剂Flux-cored wire 行走机构Traveler保护气体Shielded gas 焊接车间Welding shop焊剂垫Flux backing 引弧板Run-on tab(end tab)重力焊条Gravity electrode 引出板Run-off tab(end tab)焊剂漏斗Flux-hopper 定位板Strong-back流量计Flow meter 焊接衬垫Welding backing干燥箱Dryer 敲渣锤Chipping hammer面罩Helmet 条虫状气孔Wormhole焊工手套Welding glove 密集气孔Porosity焊钳Electrode holder 针尖状气孔Pinhole焊枪Welding gun 白点Fish eye (flake)导电嘴Tip 切口Kerf喷嘴Nozzle 咬边Undercut焊矩Torch 焊瘤overlap焊接缺陷Welding defect 凹坑Pit未焊透Incomplete penetration 烧穿Burn through未熔合Incomplete fusion 未满焊Incomplete filled groove渣Slag 清根Back chipping夹渣Slag (slag inclusion) 清渣Slag removal夹杂物Inclusion 焊接烟尘Weld fume气孔Blow hole 电光性眼炎Eye-flash焊接性Weldability 横裂纹Transverse crack碳当量Carbon equivalent 纵裂纹Longitudinal crack未焊满Incomplete filled groove 焊趾裂纹Toe crack焊接裂纹Weld crack 机械性能试验Mechanical property test热裂纹Hot crack 试板Test piece冷裂纹Cold crack 试样Specimen氢致裂纹Hydrogen –induced crack 侧弯Side bend延迟裂纹Delayed crack 弯曲Bending层状撕裂Lemellar tearing 横向拉伸Transverse tensile弧坑裂纹Crater crack 宏观试样Macro-etching specimen根部裂纹Root crack 微观试样Micro-examination specimen再热裂纹Reheat crack 破断试验Fracture test热影响区裂纹Heat-effected zone crack 抗裂试验Cracking test晶间裂纹Intercystalline crack 脆性断裂Brittle fracture塑性断裂Plastic fracture 焊接方法Welding process焊接残余裂纹Welding residual stress 焊接工艺Welding technology 消除应力Stress relieving 焊接操作Welding operation焊接变形Welding deformation 焊接顺序Welding sequence角变形Angular distortion 焊接方向Direction of welding外观检查Visual examination 常用缩语无损探伤Non-destruction testing(N.D.T.)气电立焊EGW超声波探伤Ultrasonic inspection 药芯电弧焊FCAW射线探伤（X 光）Radiographic inspection(X-rayinspection)实心电弧焊GMAW磁粉探险伤Magnetic particle inspection焊剂铜衬垫单面埋弧自动焊FCB渗透探伤Penetrate inspection 手工电弧焊SMAW熔池Weld-pool 埋弧自动焊SAW焊机（焊接电源）Weld source钨极惰性气体保护电弧焊TIG 机舱部分ENGINE ROOM PART熔化极惰性气体保护焊MIG 一、机舱设备Machines and equipment in engine room活性气体保护焊MAG 1、主机Main engine手工电弧切割SMAC 1）主机油底壳The sump tank of M.E.2）主机飞轮Fly wheel of M.E3）活塞Piston2、发电机Generator engine1）应急发电机Emergency generator engine2）辅机Auxiliary3、锅炉Boiler1）组合锅炉The composite boiler2）锅炉安全阀The safety valve of boiler3）燃烧器Oil burner unit 3）主空气瓶Main air reservoir4）水位表Water level gauge 4）应急空气瓶Emergency air reservoir5）水位控制器Water level controller 5、控制空气瓶Control air reservoir6）过量蒸气调节阀Excess steam pressure control valve6、空气干燥器Air dryer4、舵机7、分油机Oil purifier1）舵机间Steering room 1）燃油分油机Fuel oil purifier2）舵机装置Steering-gear 2）柴油分油机Diesel oil purifier3）手操舵装置Trick wheel plant 3）滑油分油机Lubricate oil purifier4）油缸Oil cylinder 4）排渣Sludge discharge5）反馈装置Feedback device 8、制淡装置Fresh water generator6）舵Rudder9、焚烧炉Incinerator舵叶Rudder blade10、油水分离器Oil water separator舵杆Rudder stock11、生活污水处理器Sewage treat plant上舵承Rudder carrier12、大气冷凝器Atmosphere condenser热水井Cascade and inspection(hotwell)5）主机燃油供给泵Main engine fuel oil supply pump滑油自清滤器The automatic back-flashlubricating oil filter6）主机燃油增压泵Main engine fuel oil booster pump燃油单元Fuel oil unit 7）主机十字头泵Main engine cross head pump1）主机燃油单元Fuel oil unit of M.E 8）付机海水泵Generator engine sea water pump2）付机燃油单元Fuel oil unit of A.E 9）付机缸套水泵Generator engine cylinder cooling water pump 3）粘度计Viscosity controller 10）锅炉给水泵Feed water pump of boiler泵Pump 11）锅炉燃油泵Fuel oil pump of boiler1）主机滑油泵Main engine lubricating oil pump12）分油机供给泵Fuel oil supply pump of purifier2）主机缸套水泵Main engine cylinder cooling water pump13）制淡海水泵Sea water pump of fresh water generator3）主机缸套水预热泵Main engine cylinder cooling water preheating pump14）压载泵Ballast pump4）主机海水泵Main engine sea water pump 15）舱底消防泵Bilge and fire pump17）油渣泵Sludge oil pump 2、柴油澄清舱Diesel oil setting tank18）柴油输送泵Diesel oil transport pump 3、燃油日用柜Fuel oil daily tank19）燃油油输送泵Fuel oil transport pump 4、燃油澄清舱Fuel oil setting tank20）汽缸油输送泵Cylinder oil transport pump 5、滑油澄清舱Lubricating oil setting tank 21）淡水输送泵Fresh water transport pump 6、滑油储藏舱Lubricating oil store tank 22）热水循环泵Hot water circulating pump 7、滑油循环舱Lubricating oil circulating tank 23）饮水日用泵Drinking water pump 8、燃油溢油舱Fuel oil overflow tank舱底消防总用泵Bilge, fire and G.S pump 9、燃油油渣舱Fuel oil sludge tank喷淋泵Sprinkling pump 10 燃油深舱Fuel oil deep tank停泊海水泵Harbor sea water pump 11 滑油污油舱Lubricating dirty oil tank12 滑油溢油舱Lubricating oil overflow tank二、各种舱（箱）柜All kinds of tank 13 滑油油渣打舱Lubricating oil sludge tank1、柴油日用柜Diesel oil daily tank 14 主机淡水膨胀水箱M.E fresh water expansion tank15 付机淡水膨胀水箱A.E fresh water expansion tank16、淡水压力柜Fresh water pressure tank 1、滑油系统Lubricating oil piping system17、热水压力柜Hot water pressure tank 2、燃油系统Fuel oil piping system18、饮水压力柜Drinking water pressure tank3、海水系统Sea water piping system19、淡水舱Fresh water tank 4、缸套水系统Cylinder cooling water piping system20、饮水舱Drinking water tank 5、启动空气系统Start air piping system21、锅炉水舱Boiler water tank 6、控制空气系统Control air piping system22、分油机工作水箱Purify operating water tank 7、排气系统Exhaust piping system23、汽缸油日用柜Cylinder oil daily tank 8、日用供水系统Daily water piping system24、尾管滑油重力柜Gravity tank of tube oil 9、蒸汽系统Steam piping system25、排气水封箱Exhaust seal water tank 10 、锅炉给水和凝水系统Feed water and condensate of boiler piping system26、蒸馏水水舱Distilling water tank 11、燃油净油系统Fuel oil purified piping system27、污水井Bilge well 12、燃油输送系统Fuel oil transport piping system三、各种管系系统All kinds of pipes舵销Rudder pintle 13、滑油净油系统Lubricating oil purified piping system舵杆衬套rudder stock liner 14、滑油输送系统Lubricating oil transport piping system舵杆轴套Sleeve for rudder stock 15、舱底压载系统Ballast and bilge water piping system舵销承衬套Bush for rudder pintle 四、仪表类Instructions舵销轴套Sleeve for rudder pintle 1、压力表Pressure gauge上舵承底座Rudder carrier seat 2、真空表Vacuum gauge舵销承座Pintle bearing 3、温度计Thermometer舵杆承座Rudder stock bearing 4、吨位表DWT gauge挡圈Retaining ring 5、遥测表Distant survey gauge舵柄Tiller 6、液全器Level switch7）舵角The angle of rudder5、空压机Air compressor1）主空压机Emergency air compressor2）应急空压机7、传感器Sensor 12、机控室Engine control room五、其它Others 13、台虎钳Vise (=vice)1、风机Fan 14、表铜截止阀Bronze close valve2、防海生物装置Anti-foul STM plant 15、表铜截止止回阀Bronze check valve3、泡沫柜Air foam tank 16、铸铁截止阀Cast iron stop valve4、中间轴Middle shaft 17、铸铁截止止回阀Cast iron check and stop valve5、尾轴Propeller shaft 18、调节阀Adjustable valve6、螺旋桨Propeller 19、溢流阀、安全阀Relief valve7、中间轴承Line shaft bearing 20、减压阀Reducing valve8、泡沫灭火机Foam fire extinguisher 六、材料Material9、饮水消毒装置Sterilizer plant 1、管子Pipe10、主配电板Main switch board 2、无缝钢管Seamless steel pipe (tube)11、机舱集控台Engine room control console 3、紫铜管Purple copper pipe4、铁法兰Iron flange 18、支架（马脚）Clamp5、铜法兰Copper flange 19、油漆Paint6、盲板法兰Blind-flange 20、备件Spare parts7、螺丝（螺栓）Bolt8、双头螺丝Stud 七、生产工具Produce tool9、螺帽（螺母）Nut 1、图纸Drawing10、不锈钢螺丝Stainless steel bolt 2、活络钣Adjustable spanner11、垫片（床）Gasket 3、令司板（梅花钣）Ring spanner12、橡皮床Gum gasket 4、开口钣Open –ender spanner13、纸箔床Paper copper gasket 5、管子钳Pipe wrench14、紫铜床Purple copper gasket 6、凿子Chisel15、石墨床Black lead gasket 7、锒头Hammer16、青铅床Black lead gasket 8、锉刀File17、佛纳Feeler gauge 9、螺丝刀Screwdriver10、油漆滚筒Paint roller 4、首先请检查安装说明和电气绝缘11、油漆刷子Paint brush Please check the condition of installation and insulationfirst12、钢锯Hacksaw 5、我们准备将油水分离器动转13、套筒扳手Socket spanner Now we will run the oily-water separator14、手电筒Torch 6、请检查动转情况15、钻头driller Please check the running condition八、英语会话7、接着我们一个一个地做报警/安全保护装置的功能试验1、早上好good morning Now we will do the function test about alarm and safetydevice2、今天我们准备交验油水分离器8、设备交接基本结束Today we will test the oily-water separator. Now the test is over3、请跟我来9、请部有何修改意见？Please fellow me. Do you have any question ?10、非常感谢17、这里增加一只落水斗Thanks Add a drain plug here11、再见18、请用空气压缩空气吹干Good bye Please dry it by the compressed air12、请把这对法兰撬紧松开19、我将回车间支拿肥皂水Please tighten/release the flange I will com to my workshop to take some soap water13、这路管子是从发电机单元来的20、这个系统非常重要的，一定要认真检查The piping is from to the G/E unit This system is very important ,please check it carefully14、这对法兰/接头在漏21、请交验收整改意见This flange /connection is linking Please check your remarks15、这路系统的试验压力是7 公斤22、天太热了，请休息一会The test pressure of the piping system is 7 bar It’s too hot ,please take a rest16、这里请加强please make a clamp here 23、我负责这项工作I am in charge of this job电气部分ELECTRIC PART一、常用词汇Words and expression 模拟Analog(ue)2182 千赫值班接收机2182KHz watch receiver 锚灯Anchor lightA 异常Abnormal 风速风向仪Anemorumbometer应答Acknowledge 阳极Anode有功功率Active power 天线Antenna执行器Actuator 天线馈线连接器Antenna feeder connector调整Adjust 天线引入绝缘端子Antenna leading –in insulator空气断路器Air circuit breaker 天线共用器Antenna multicoupler报警系统Alarm system 天线调谐器Antenna tuner交流电Alternating current 电焊机Arc welder电流表ammeter 声音的Audible放大器Amplifier 自动海图标绘仪Auto chart plotter自动舵Auto pilot自动的Automatic自动雷达标绘仪Automatic radar plotting aid球鼻首警告灯Bulbous bow warning light自动电话Automatic telephone 汇流排Bus(-)bar电压自动调节器Automatic voltage regulator 汇流排Bus –tie –in自动化系统Automation system 蜂鸣器Buzzer压载控制台Ballast control console C、电缆Cable镇流器Ballast 电缆填料函Cable gland底座Base 敷设电缆Cable laying电池Battery 电缆管Cable pipe (conduit)铃Bell 电缆扎带Cable strap弯曲Bend 电缆托架Cable tray床头灯Berth light 校准器Calibrator失电Black out 电容capacitor刹车Brake 阴板Cathode电刷Brush 警告牌Caution plate顶灯Ceiling light 通讯Communication中央处理器Central processing unit 计算机Computer通道Channel 接头Connector充电器Charger 恒电流Constant current充放电板Charging&discharging board 消耗Consumption海图灯Chart table light 触头Contact检查Check 接触器Contactor芯片Chip 控制箱Control box清洁Clean 控制箱Controller雨雪清除器Clear view screen 芯线Core二氧化碳释放报警CO2 release alarm 角灯Corner light同轴电缆Coaxial cable 计算器Counter线圈Coil 电流Current冷库呼叫Cold store calling D、损坏Damage危险气体报警箱Dangerous gas detecting&alarm box双极单刀开关Double pole single way switch白昼信号灯Daylight signal light 双极双刀开关Double pole two way switch 去耦Decoupling set 天线收发转换开关Duplexer台灯Desk light 值班水手呼叫Duty sailor calling控测器Detector 接地Earth拨号Dial 接地排Earth bar数字选择呼叫收信机Digital select –call receiver测深仪Echo sounder调光器dimmer 电工试验板Electric test panel直流电Direct current 电机员Electrical engineer直接起动Direct –on –line starting 电极Electrode磁盘Disk 应急照明分电箱Emergence lighting distribution box显示Display 应急示位标Emergence position indicating radiobeacon遇险信息控制器Distress message controller 应急停Emergence stop多普勒记程仪Doppler speed log应急配电板Emergency switch board 馈电品Feeder panel机舱报警Engine alarm 滤波器Filter集控台Engine control console 火警复显器Fire alarm repeater机舱监测报警Engine room monitoring&alarm system防火风闸控制单元Fire damper control unit轮机员呼叫Engineer calling panel 火警检测箱Fire detecting box轮机员安全Engineer safety system 火焰探头Flame detector增强群呼叫收讯机Enhance group call receiver 闪光灯Flash light交换机Exchanger 浮充电Float charge防爆灯Explosion proof light 强光灯Flood light延伸报警板Extension alarm panel 流程图Flow chart故障Failure 流量开关Flow switch故障Fault 荧光灯Fluorescent light反馈Feed back 雾笛Fog horn频率Frequency熔丝Fuse 感温探头Heat detector填料Gasket 底座Holder通用报警General alarm 电笛、喇叭Horn发电机Generator 病房呼叫Hospital calling发电机屏Generator panel 照明Illumination（铜）锣、钟Gong 白炽灯Incandescent light全球卫星定位导航GPS navigator 指示器Indicator组合灯板Group alarm light pillar 卫星 B 站INMARSAT B station组合起动屏Group starter panel 卫星 C 站INMARSAT C station电罗经Gyro compass 输入输出Input /output卤素灯Halogen light 安装Install听筒Handset 仪表Instrument硬件Hardware 绝缘胶带Insulating tape航向Heading 绝缘Insulation接口、界面Interface 限位开关Limit switch连锁Interlock 连接Link中断Interrupt 负载Load逆变器Inverter 劳莱收信机Loran receiver接线盒Junction box 磁罗经Magnetic compass键盘Keyboard 主机电子调速器Main engine electronic governor灯泡Lamp 主机功率、纽力仪Main engine power& torque unit液位开关Level switch 主机遥控系统Main engine remote control system液位传感器Level transmitter 主机转速表Main engine revolution meter灯Light 主机安全系统Main engine safety system灯柱Light column 主机增压器转速表Main engine turbo-charger speed meter 照明分电箱Light distribution box 主配电板Main switchboard避雷针Lighting arrester 手动手册Manual标记Mark 移动Move桅杆Mast light 万用表Multimeter母子钟Master& slave clock 铭牌Name plate匹配箱Matching box 窄频直接打印机Narrow-band direct printer测量Measure 航行灯Navigation light兆欧表Megohmmeter 导航系统Navigation system仪表Meter 航行监控台Navigation watch console话筒Microphone 航行警告收信机NAVTEX receiver镜向灯Mirror light 负极Negative监视器Monitor 网络Network莫斯键Morse key 标称值Nominal value电动机Motor 常闭Normally closed塑壳断路器Moulded case circuitbreaker常开Normally open鼠标Mouse 失控灯Not under-command light欧姆表Ohm gauge 正极Positive欧姆收信机Omega receiver 功率、电源Power车钟记录仪Order printer 电力分电箱Power distribution box示波器Oscilloscope 功率因素Power factor过电流Over current 优先卸载Preferential trip过载Overload 压力开关Pressure switch巴拿马动河操舵灯Panama canal steering light 压力传感器Pressure switch 并联、并车Parallel 一次系统Primary system相Phase 打印机Printer光敏电阻Photo resister 程序Program测速传感器Pick up 螺旋桨警告灯Propeller warning light插头Plug 广播Public addressor左舷灯Port light 脉冲Pulse便携电话Portable telephone 按钮Push button雷达Radar 电阻Resistance雷达应答器Radar transponder 逆功率Reverse power收音机Radio 旋转灯Rotating light无线电测向仪Radio direction finder 舵角指示器Rudder angle indicator随机存取存储器Radio system 运转灯Running lamp额定Random access memory 屏幕、屏蔽Screen无功电流Rated power 螺丝刀Screwdriver插座Receptacle 搜索灯Search light录音机、记录仪Recorder 二次系统Secondary system整流器Rectifier 串联Series继电器Relay 屏蔽Shield复位Reset 船名灯Ship name light岸电箱Shore connection box短路Short circuit展示、给-----看Show 电磁阀Solenoid valve分励脱扣Shunt trip 消音Sound off停车Shut down 声力电话Sound power telephone签字Sign 空间加热器Space heater信号集合箱Signal acquisition unit 扳手Spanner信号灯Signal light 喇叭Speaker单边带收发机Single side band transceiver分配器Distributor电笛Siren 右舷灯Starboard light慢车Slow down 起动Start烟气探测报警箱Smoke detecting &alarm box 起动带Start感烟探头Smoke detector 尾灯Stern light插座Socket 停止Stop软件Software 苏伊士运河尾灯Suez canal stern light电烙铁Soldering iron 支撑物supporter开关Switch 验电笔Test pen打开Switch on 试验程序Test procedure关闭Switch off 热敏电阻Thermistor同步屏Synchronizing panel 热电偶Thermocouple同步表Synchronoscope 温度计Thermometer转速表Tachometer 恒温计Thermostat录音机Tape recorder 触摸屏Touch panel车钟Telegraph 轨迹球Trackball电视Television 收发机Transceiver温度开关Temperature switch 传感器Transmitter温度传感器Temperature transmitter 变压器Transformer接线柱Terminal 脱扣Trip接线排Terminal board 欠电压Under voltage试验Test 不中断电源Uninterrupted power source卸载Unload 二、会话Dialog and conversation超高频VHF telephone 船东o- owner视觉的Visual 验船师s-survey电压Voltage 检验员q-quality inspector电压表Voltmeter 电工e-electrician壁灯Wall light 1、检验电缆敷设瓦特Watt Inspection cable laying波道Waveguide 你能带我去看机舱电缆敷设气象传真收信机Weather fax receiver Q: could you show me cable laying of engine room?驾控台Wheel speed &directionindicator好，走吧。
各种船舶的英语翻译_交通运输英语词汇
dugout 独木舟barge 驳船kayak (爱斯基摩人的)木排outrigger 桨叉架船rowing boat 划艇(美作:rowboat)gondola (意大利的)长平底船whale mother ship 捕鲸母船hydrofoil 水翼船catamarans 双体船dredger 挖泥船boat 船brig, brigantine 双桅船canoe 小船,独木舟caravel 快帆船cargo boat 货船coaster 近海贸易货船cod-fishing boat 捕鳕鱼船whaler 捕鲸船collier 运煤船battleship 战船shallop 小型战船coastguard cutter, coastguard vessel 巡逻艇,缉私艇revenue cutter 缉私船patrol boat 巡逻艇minelayer 布雷艇minesweeper 扫雷艇torpedo boat 鱼雷艇frigate 轻护航舰gunboat 炮舰submarine 潜水艇destroyer 驱逐舰corvette 轻巡洋舰cruiser 巡洋舰aircraft carrier 航空母舰ferry, ferryboat 渡船,渡轮fishing boat 渔船freighter 货船galleon 大型帆船galley 大划桨船hovercraft 气垫船icebreaker 破冰船launch 艇lifeboat 救生艇lighter 驳船liner, ocean liner 远洋班轮merchant ship, merchantman 商船motorboat 摩托艇outboard 尾部装有马达的小艇paddle steamer, paddle boat 明轮船passenger boat 客船piragua, pirogue 独木舟raft 木筏rowing boat 划艇sailing boat, sailing ship 帆船schooner 纵帆船ship 船skiff 小艇sloop 单桅船steamer, steamship 汽轮tanker 油轮trawler 拖网渔船tug, tugboat 拖轮vessel 船yacht 游艇yawl 船载小艇。
船舶术语翻译
船舶术语VOCABULARY3-roller bending machine 三弯机abandon v. 弃船 abolish v. 消除ABS 美国船级社 acceleration n. 加速度accelerometer n. 加速度表 accommodate v. 容纳accommodation deck起居(住舱)甲板 accuracy n. 精度accurate synchro device准同步装置 acetylene cutter 气割机acid-pickling n. 酸洗 acoustics n. 音响效果adhesiveness n. 粘附力 adjacent a.相邻的adjust v. 调节 administration n. 行政管理admit v. 接纳 adopt v. 采纳，采用affiliated factory 分厂，附属工厂 aforementioned a.前述aft a. adv. n. （在）船艉 aft peak 艉尖舱after service 售后服务 ahead n. 正车air bottle 空气瓶 air compressor 空压机air reservoir 气瓶 air siren 汽笛air-tight test 气密实验 alarm bell 警铃alignment n. 找中，校准 all waves 全波allowance n. 允值 all position 全方位alternating current ( A.C.) 交流电 ammonia n. 氨amplify v. 放大 an automatic production line自动生产线analogous output 模拟输出 analogue computer 模拟计算机anchor n. 锚 anchor chain （cable chain）锚链anchor handling 锚操纵 anchor windlass (chain windlass)起锚机anchorage buoy 系泊浮筒 angular n. 角度antenna n. 天线 anticorrosion precaution 防腐措施apparatus n. (pl. apparatus or apparatuses)仪器，器械，装置appearance n. 外观 approval n. 批准，认可approve vt. 认可 arbitrate v. 仲裁arc n. 弧度 arduous a.艰难的arrange v. 布置，安排 asbestos n. 石棉assemble v. 装配 Assemble Language 汇编语言assembly n. 装配 astern n. 倒车atmospheric survey 大气环流调查 atomic power 原子能atomize v. 雾化 authority n. 当局automatic control device 自动控制装置automatic production line 自动生产线 automatic steering 自动操舵automatic submerged arc welding 自动埋弧焊automatic telephone 自动电话 aux. boiler 副锅炉aux. engine 辅机 aux. engine room 辅机舱aux. machinery 辅机 auxiliary means 辅助手段auxiliary system 辅助系统 axial push 轴向推力backing n. 衬垫 ballast piping 压载水管系ballast pump 压载泵 ballast system 压载系统ballast water 压载水 base n. 基准base point n. 基准点 basic design 基本（方案）设计basic metal 母材 battery unit 蓄电池组beam n. 波束 beam n. 横梁bearing n. 轴承 bearing hole n. 轴承孔bedplate n. 机座 bell set 铃组bending machine 冷弯机 berth n. (水平)船台，（船上）床铺berth or slipway fabrication 船台装配 bilge n. 舱底水bilge keel 舭龙骨 bilge plate 舭板bilge pump 舱底水泵 bilge system 舱底水系统binary system 二进位制 blank n. 毛胚block n. 分段 block or section fabrication 分段或总段装配blood vessel 血管 blower 风机blue collar worker 蓝领,工人 boat deck 艇甲板bollard n. 带缆桩 bolt n. 螺栓bolthead n. 螺栓头 bottom n. 船底bottom plate 底板 bottom structure 底板结构bow n. 船艏 bow &stern structure 艏艉结构bow section 艏段 branch company 分公司，子公司branch system 分系统 bridge n. 桥楼bridge control 桥楼控制 broadcast n. v. 广播broadcast station 广播站bronze sleeve 青铜套筒bulbous bow 球鼻艏bulk cargo 散装货物bulk-cargo carrier 散装货船bulkhead n. 隔舱壁bulkhead structure 隔舱壁结构bushing n. 衬垫butt joint 对接接头cabin n. 舱室cable fixture 电缆夹具calculation n. 计算calculator n. 计算器calibrate v. 校正calibration n. 校正cam n. 凸轮cam follower 凸轮附件camber n. 梁拱camshaft n. 凸轮轴capstan windlass（anchor winch）锚绞盘cargo n. 船货cargo oil 货油cargo –hold n. 货舱cargo-lifting n. 起货casing n. 罩壳cast iron piece 铸铁件casting n. 铸造cathode-ray type 阴极射线式CCS 中国船级社central control 集控centreline n. 中心线centrifugal a.离心的certificate n. 证书chain drive 链传动chain locker 锚链舱chain pipe 锚链管chain reaction 连锁反应chain stopper 制链器challenge n. v. 挑战chamfer v. 在边缘切斜面changeover switch 转换开关characteristics n. 性能，特性，特征charge v. 充（电，气）check n. v. 检验chemical medium 化学介质China Classification Society(CCS) 中国船级社China Ocean Shipping Company (COSCO) 中国远洋公司chip n. 芯片circle n. 圈子，团体class n. 船级classification n. 船级classification society 船级社cleanness n. 清洁度closed circulation 闭式循环clutch n. 离合器CO2 shielded arc welding 二氧化碳气体保护焊Coating n. 图层code n. 法典code display circuit 编码显示电路coefficients of ship form 船型系数cold processing 冷加工collision n. (船只)碰撞combustibility n. 可燃性combustion n. 燃烧combustion chamber 燃烧室combustion gas 燃气commanding telephone 指挥电话communication n. 通讯compartment n. 分隔舱compartment stuffing box 隔舱填料函compass n. 罗经compass deck 罗经甲板compensate vt. 补偿competition n. 竞争completion drawing 完工图component n. 组成部分composition n. 成分组成compound excitation 复励comprehensive productivity 综合生产能力compressed air 压缩空气compression (power)stroke n. 压缩冲程computer control console 计算机控制台conceptual a. 概念的condensation n. 冷凝conductor n. 导体connecting rod 连杆connection n. 接头constant voltage 恒压constitute v. 构成consumables n. 消耗品consumption n. 消耗contact v. 触发container n. 集装箱continuous deck 连续甲板contract n. 合同contradiction n. 矛盾control component 控制元件control console 控制台control unit 控制装置converse method 反装法convertor n. 转换器conveyor n. 传送带coolant n. 致冷剂coolant(cooling agent)n. 制冷剂cooler n. 冷却器cooling system 冷却系统cooperation n. 合作coordinate n. 坐标core enterprise 核心企业corrosion n. 腐蚀corrugated a. 波纹状的course n. 航向cover n. 药皮CPP drive 可调浆传动crank cheek 曲柄夹板crankcase n. 曲柄箱crankpin n. 曲柄臂crankshaft n. 曲轴crankweb n. 曲柄臂crew n. (全体)船员cross section 截面crosshead n. 十字头cultivate v. 培养，培育current n. 电流current n. 洋流，水流current-impulse frequency convertor 电流-脉冲频率变换器curve n. 曲线cutting n. 切割cylinder n. 气缸cylinder block 气缸体cylinder cover (cylinder head) 缸盖cylinder liner 气缸衬套cylinder oil 气缸油cylinder wall 缸壁data impulse 数据脉冲davit n. 吊艇架deadweight ton(DWT) n. 载重量，吨载量Decca receiver 台卡定位仪deck n. 甲板deck girder 甲板材deck longitudinal 甲板纵骨deck machinery 甲板机deck plate 甲板板deck structure 甲板结构deckhouse 甲板室deform v. 形变deliver v. 交货，交船delivery n. 交船，交货delivery ceremony 交船典礼derrick n. 吊杆design stage 设计阶段designation n. 名称，牌号designation n. 目的地detail design 详细（施工）设计detect v. 探测detect v. 侦察detection n. 探测deviation n. 位移dial n. 刻度盘diameter n. 直径differentia n. 差异digital computer 数字计算机digital output 数字输出direct current(D.C.)直流电direct drive 直接传动direct telephone 对讲电话，直线电话directional finder 测向仪directional instrument 指向仪器directional stability 航向稳定性disc n. 圆盘discharge n. v. 排水dispensable a. 非必要的dispute n. v. 争端，争执distribute v. 分布distribute v. 分配，配电distribution n. 配电distribution box 分电箱distribution panel 区配电板distribution switch 配电开关distribution system n. 配电系统division n. 划分DNV 挪威船级社Dock n. 船坞dock trial 码头试验docking winch 带缆绞车Doppler effect 多普勒效应Doppler frequency offset 多普勒频移Doppler sonar log 多普勒声纳计程仪double bottom 双层底double-action a.双作用down-vertical welding 下行焊draft(draught)n. 吃水drainage n. 疏水，泄水drawing n. 图纸drawing instrument 绘图仪drift v. 漂移drinking water 饮用水drip-proof type 防滴式drive n. 传动drive mechanism 传动机构drive mechanism 传动装置drive unit 传动装置driven shaft 从动轴dry v. 烘干drydock n. 干船坞dynamic –pressure type 水压式echo signal 返回信号echo sounder 回声测深仪economic effect 经济效益edge preparation 边缘加工edge processing 边缘加工edger n. 刨边机eject v. 喷射elapse v. （时光）消逝electric brain 电脑electric load 负荷electrical arc 电弧electrical compass 电罗经electrical drive 电力托动electrical energy 电能electrical impulse 电脉冲electrical power 电力electrical shedding 放电electrical signal 电器信号electrical slag welding 电焊渣electrical unit 电器装置electrical user 电器设备electrical-driven a. 电动的electrician n. 电工electricity outfitting 电舾electrode n. 焊条electromagnetic contactor 电磁接触器electromagnetic induction 电磁感应electromagnetic log 电磁计程仪electromagnetic sensor 电磁传感器electronic computer 电子计算机electronics n. 电子（学）element n. 机械零件element n. 要素emerge v. 崛起，兴起emergency control 应急控制emergency network 应急电网emergency power station 应急电站emergency radio transmitter 应急无线电发信机emergency steering 应急操舵emergency switchboard 应急配电板emergency telegraph 应急传令钟emergent discharge 应急排放emergent service 应急使用enclose v. 封闭encounter v. 遭遇energy convertor 换能器engine foundation (engine seat )机座engine frame 机架engine oil 机油engine outfitting 机舾engine space 机舱engineer n. 轮机员engineer n. 工程师engineering and technical team 工程技术队伍engineer vessel 工程船engine-room 机舱ensure v. 确保enterprise n. 企业EO 无人机舱equipment n. 设备error n. 误差essence n. 实质，本质evolve v. 渐进，进化，演变excessive a. 过量的，极度的excitation n. 励磁excite v. 激励exhaust port 排气口exhaust stroke 排气冲程exhaust valve 排气阀expand v. 扩张，扩建expansion n. 展开图expansion stroke 膨胀（作工）冲程expansion tank 膨胀箱experiment n. 实验exterior force 外力extinguish v. 灭火F.O.meter 燃油流量计F.O．tank 燃油舱Fabricate v. 装配，制作fabrication n. 装配facile adaptability 灵活的适应性facsimile transmission(fax)传真fairing n. 光顺体，流线体fair-lead n. 导缆孔fashioned steel 型钢fast speed (rapidity)快速性fathometer n. 侧深仪feed v. 馈给feed circuit 馈电线路fillet seam 角焊缝fillet welding 角焊filter n. 过滤器. 过滤fine a. 纤细的finished product 成品fire alarm 火警fire hazard 火灾fire pump 消防泵fire-fighting system 消防系统fire-resistant a.耐火的fixed part 固定件flash signal light 闪光信号灯flat fillet seam 平角焊缝flexibility n. 挠性flexible coupling 挠性联轴节float launching 漂浮下水floatability n. 漂浮性floating positively 正浮floating production storage unit(FPSU) 浮式生产储油轮flood v. 进水floodability n. 不沉性floor plate 肋板fluctuate v. 波动fluctuation n. 波动flush v. 清洗flushing agent 清洗剂flux n. 焊剂flywheel n 飞轮foam n. 泡沫folding machine 折边机for home use 国内用forced lubrication 强制润滑forced ventilation 机械通风fore perpendicular 艏垂线forecastle n. 艏楼foreign trade 外贸forging n. 锻造formation n. 构成，结构frame n. 肋骨framework n. 框架framing block 肋骨框架分段free end 自由端freeboard n. 干舷freighter n. 货船Freon n. 氟利昂frequency n. 频率frequency difference latching 频率锁定frequency regulation 调频fresh water （F.W.）淡水fresh water production plant造水装置friction resistance 摩擦阻力fuel n. 燃料fuel nozzle 喷油嘴fuel oil 燃油fuel oil （F.O.）燃油fuel pipeline 燃油管系full-load a. 满载的full-load displacement 满载排水量funnel n. 烟囱galley n. 厨房gantry n. 龙门架gas cutting 气割gas tight seal 气密密封gas turbine engine 燃气轮机gas welding 气焊gear n. 齿轮gear drive 齿轮转动geo-physical propecting vessel 地球物理探测船GL 西德劳氏船级社grant v. 给予……的权利gravity centre 重心gravity welding 重力焊groove v. 开坡口ground v. 接地group n. (企业)集团growth n. 生长，发育guarantee n. v. 保证general description 概述general-purpose a.通用的generating set 发电机组geometrical characteristics 几何特征geometrical principle 几何原理gravity launching 重力下水guided-missile frigate 导弹护卫舰gyro n. 陀螺仪gyro compass 陀螺罗经，回转罗经H.D.Heavy Machinery Co. Ltd. H.D.重机股份有限公司Halogen n. 卤素hand control 手控hand level 手柄hand steering 手动操作hand wheel 手轮handle v. 操纵harbour n. 港口，停泊harbour generator 停泊发电机hardware n. 硬件hatch trunk 舱口围壁hawsepipe n. 锚链筒he water pressure system 水压系统headquarters n. 总部，厂部headroom n. 甲板间高度heat exchanger 热交换器heating n. 供暖heavy current n. 强电heavy oil 重油heel n. 横倾hereinbelow adv. 在下文high frequency 高频high-speed boat 高速艇horizontal a.水平的，卧式的horsepower(hp) n. 马力hose n. 软管hot processing 热加工hot work 火工hull n. 船体hull cleanness 船体光顺性hull construction 船体结构hull form 船型hull line 船体线型hull structure 船体结构human brain 人脑humidify v. 增湿hydraulic a. 液压的hydraulic fluid 液压流体hydraulic machine 液压机hyperbolic curve receive双曲线定位仪identify vt.识别ignite v. 点火ignition n. 点火illumination n. 照明illustration n. 生动的说image display system 图象显示系统IMCO 政府间海事协商组织impact n. 冲击implication n. 含义impulsator n. 推动器，脉冲发生器impulse-type a.脉冲式的impurity n. 杂质inclination n. 倾斜inclination test 倾斜试验incline v. 倾斜index n. 索引indication n. 显示indicator n. 显示仪indicator n. 指示器indicator light 指示灯indicator valve示功阀inert gas 惰性气体inertia n. 惯性inertia platform 惯性平台inevitable a.不可避免的initial metacentric height 初稳心高inject n. 喷射injecting system 喷油系统injector n. 喷油器inner bottom longitudinal 内底纵骨inner bottom plate 内底板inner ring 内环input n. v. 输入inspector n. 质检员installation n. （船上）安装installation error 安装误差instancy speed 瞬时速度instrument n. 仪表,仪器insulating material 绝缘材料insulation n. 绝缘intake n. 吸入intake port 汲气口intake valve 进气阀integral casting 整体浇铸intention n. 意向intercommunication (intercom)n. 内通，内部通讯interfering moment 干扰力矩intermediate bearing 中间轴承intermediate shaft 中间轴internal combustion engine 内燃机international authorities 国际当局Internet 因特网（国际互连网）introduce v. 引进，引入，介绍iron powder electrode 铁粉焊条jig n. 胎架joint design 联合设计journal n. 轴颈keel n. 龙骨keel plate 龙骨板keep station 定位kerosene test 煤油实验key enterprise 骨干企业kilohertz 千赫kinetic energy 动能knot n. 节labyrinth n. 迷宫，曲径land-based a. 路基的landing-place n. 码头lap joint 搭接接头large-computer(mainframe computer) n. 大型（计算）机，主机lay v. 敷设length n. (一)节，（一）段level n. 液位level gauge 液位计level relay 液位继电器license n. 许可证life line 生命线life-belt n. 救生圈life-boat n. 救生艇life-jacket n. 救生衣life-or-death a.生死攸关的life-raft n. 救生筏life-saving n. 救生lifting capacity 起重能力light current 弱电lighting n. 照明light-ship displacement (light-load displacement)轻载排水量lines lofting 线型放样lines offsets 型值lines plan 线型图lining n. 衬垫load distribution 负荷分配load line mark 载重线标志load transfer 负荷转移local strengthening 局部加强locate v. 定位lock washer 锁紧垫片lofting n. 放样log n. 计程仪logical a.逻辑的long bridge 长桥楼longitudinal a.纵向的longitudinal (uniflow)scavenge 直流扫气longitudinal bulkhead 纵隔舱壁longitudinal framing 纵向构架loop n. 回路loop antenna 环状天线Loran receiver 劳兰定位仪Loudspeaker n. 扬声器low speed 低速lower deck 下甲板LR 英国劳氏船级社lube oil 润滑油lube oil(L.O.)滑油lube oil pump 滑油泵lubricant n. 润滑剂lubricant film 润滑油膜lubricating oil 滑油lubrication system 滑油系统M.E.engine room 主机舱Machine v. 机加工machinery n. 机械machinery set 机组machinery workshop 机电车间machining n. 机加工machining workshop 机加工车间magnetic compass 磁罗经magnetic field 磁场magnetic needle 磁针magnetic object 磁性物体magnifier n. 放大器magnify v. 放大magnitude n. 大小main bearing 主轴承main engine (ME) 主机main generating set 主发电机组Main Group 1 第一大部分main hull 主船体main network 主电网main power station 主电站main switchboard 主配电板maintenance n. v. 维护，保养marker n. 厂商man power resource 人力资源management n. 生产管理maneuver v. n. 操纵maneuverability n. 操纵性maneuvering console 操纵台maneuvering system 操纵系统manual work 手工劳动manufacture n. &v. 生产，制造marine crane 船用起重机marine diesel engine 船用柴油机marine engineer 机电工程师marine engineering research institute 造机研究所marine geological research vessel 海洋地质调查船mark v. 标出mast lightmaster controller 主令控制器Master degree 硕士学位material n. 材料material marking 下料mathematical a.数学的mathematical lofting skill 数学放样技术maximum(max.)n. 最大means n. 手段，工具measurement laboratory 计量实验室measuring meter 测量仪表measuring point 测量点mechanical energy 机械能mechanical launching 机械下水mechanical processing 机加工mechanical unit 机械装置medium speed 中速medium wave 中波medium-computer n. 中型（计算）机member n. 构件memory n. 储存器，内存memory and storage system 储存系统merchant ship 民用船mercury n,水银meridian n. 子午线metacentre n. 稳心metal recovery 金属回收率metallic equipment 冶金设备microclimate n. 小气候microcomputer n. 微机microprocessor n. 微处理器midship n. a. adv. 舯部military ship 军用船miller n. 铣床minicomputer n. 小型（计算）机minimize v. 降至最低minus push 负推力minus value 负值miscellaneous a. 杂项的mobilize v. 动员model case 样箱model plate 样板model rod 样棒moderate a. 中型的modern enterprise system 现代企业制度modus n. 操纵法（pl. modi）monitor v. 监视monitoring device 监控装置moor v. 系泊motive power 原动力motor n. 电动机mould loft 放样台mouth n. 河口moving part 运动件multi-purpose a. 多用途的，综合的multi-stage n. 多级mutual benefit 互惠互利nautical mile 海里naval architect 造船设计师navigating instrument 导航仪器navigating zone 航区navigation computer 导航计算机navigation equipment 导航设备navigational light 航行灯navy n. 海军navy underway replenishment ship 海军航行补给船NC cutting machine 数控切割机nerve cell 神经细胞nesting n. 套料network n. 电网nil n. 零，无NK 日本海事协会non –ferrous metal 有色金属non-restrictive a. 自由的，不受限制的non-standard product 非标产品non-transparent a. 不透明的normal displacement 正常排水量normal shipping 正常营运nozzle n. 喷嚏numbering system 计算系统numeral n. 数字numerical control (NC)数控numerical control cutter 数控切割机nut n. 螺母observation n. 观察occasion n. 盛事，盛举ocean-going vessel 远洋船oceanographic research vessel 海洋调查船offshore service 近海作业oil charging piping 注油管系oil consumption 油耗oil filling port 注油口oil mist 油雾oil refinery 炼油厂oil tanker 油船oil-resistant a.耐油的oil-tight n. 油密Omega/satellite integrated navigation instrument 奥米加/卫星导航系统one-side welding单面焊接，双面成形one-way a.单向的open chamber 开放式燃烧室open circulation 开放循环opening n. 开口operating cycle 工作周期operation n. 施工operation n. 运行，运转operation surroundings 作业环境operator n. 操纵员opportunity n. 机遇optical projector 光学仪器optics n. 光学orbit n. 轨道order n. v. 订单，定购oscillation n. 振荡oscillation current 振荡电流outboard adv. 向舷外outer appearance 外观outer ring 外环outfitting n. 舾装output n. 输出overload v. 过载owner n. 船东owner’s representative 船东代表oxide n. 氧化皮paint n. 油漆pain-taking a.艰巨的painting n. 涂装painting n. 涂装，油漆工艺palletizing management 托盘管理parallel n. 并联 v. 并车parallel of generators 发电机并车parameter n. 参数part n. 部件，机械部件part fabrication 部装particle n. 颗粒party n. (谈判或合同之)一方passage n. 通道passageway n. 通道passenger-cargo vessel 客货船performance n. 性能permanently adv. 永久的perpendicular n. 垂线personnel n. 全体人员personnel n. 人员，人事phase angle 相角phase sequence 相序phase –sensitive rectifier 相敏整流器physical quantity 物理量physical-chemical experiment 理化实验physical-chemical experimental center 理化中心实验室pillar n. 支柱pilot n. 驾驶员，领航员，舵轮pipe connection 管子接头pipe flange 管子法兰piping system 管系piston pin 活塞环piston pin 活塞梢piston stroke 活塞冲程pitch n. 纵摇plan n. 图纸plane n. 平面plane v. 整平planing machine 校平机plant n. （成套机电）设备platform n. 平台pneumatic tool 气动工具pointing of direction 指向poisonous gas 有毒气体pollution n. 污染poop n. 艉楼port n. 左舷portable light 手提灯postdoctoral centre 博士后工作站potable water 饮用水pour v. 涌入，源源不断power amplifier 功率放大器power plant 动力装置,(火力)电厂power station 电站power supply 电源，供电power system 电力系统,动力系统practice n. 习惯做法preamplifier n. 前置放大器pre-combustion chamber 预燃燃烧室pre-heat v. 预热pressure container 压力容器pressure relay 压力继电器pressure sensor 压力传感器pressure tank 压力柜pretreat v. 预处理primary radio transmitter 主无线电发信机prime mover 原动机primer n. 底漆primer painting 涂底漆principle dimensions 主尺度process n. 工艺，流程v. 加工，处理production efficiency 生产效率production line 生产线production procedure 生产程序program n. 程序projection plane 投影面prolong v. 延长promote v. 促进，晋升propeller n. 螺旋桨proportion n. 比例propulsion efficiency 推进效力propulsion plant 推进装置protection type 保护式provision n. 食品pump n. 汞purity v. 净化push rod 顶杆push-pull magnetic amplifier 推挽磁放大器pyramid method 正装法quality assurance 质量保证quality control 质量控制quality management 质量管理quality policy 质量方针quay n. (顺岸式)码头quiescent a.安静的radar n. 雷达radio beacon station 导航台radio communication equipment 无线电通讯设备radio directional finder 无线电测向仪radio message 无线电报radio receive 无线电接收机radio room 报房radio station 电台radio transmitter 无线电发信机radio wave 无线电波range n. 航程range v. 测距range display 航程显示器range unit 航程装置rated power 额定功率rated value 额定值reaction n. 反作用力reading n. 读数receiver n. 接收器reciprocating movement 往复运动rectification n. 矫正，整顿rectify v. 整流，滤波reduction gear 减速齿轮reduction gearbox 减速齿轮箱reduction unit 减速装置reduction with an astern clutch 带到车离合器的减速reefer n. （俗）冷藏船，冰箱reflect v. 反射refrigerating plant 制冷装置register n. (机)验船师register vt. 登记，注册regulation n. 登记regulator n. 调整器relative humidity 相对湿度relative motion 相对运动relay contactor 继电器remains n. 残余remote control 遥控remote control station 遥控站rescue v. n. 救援rescue frequency 救援频率rescue transmitter 救援发信机resemble v. 相似reserve buoyancy 储备浮力reservoir n. 容器resistance n. 阻力resistance heat 电热阻rest v. 靠左retaining washer 保护垫片retake v. 回收，取回reversal n. 换向reverse v. 反向逆转reverse power 逆功率reversing system 换向机构revolution n. 旋转rigid a. 刚性的ring seam 环缝rock arm 摇臂roll n. 横摇roller machine 滚床room n. 余地rope n. 缆索rotary movement 旋转运动rotate v. 旋转rotating direction 旋转方向rotation n. 旋转度rotor n. 转子rough sea 波涛汹涌roughness n. 粗糙度routine n. 例行公事rpm 转速rudder n. 舵rudder angle indicator 舵角指示器rudder carrier 舵承，舵托rudder stock 舵轴，舵杆rudder stopper 舵角限制器rules n. 规范，规则running n. 经营管理rust preventative 防锈剂rust prevention 防锈rust removal 除锈rust-proof a.防锈的safeguard v. 捍卫safety valve 安全阀salt content 含盐量sanitary water 卫生水saturated steam 饱和蒸汽scavenge v. n. 扫气scavenge box 扫气箱scavenge flow 扫气气流scavenge pattern 扫气型式screen n. 荧光屏screw shaft 螺旋桨轴sea damage 海损sea trial 试航sea water (SW)海水sea-chart room 海图室seakeeping performances 航海性能，试航性seal n. v. 密封sealing agent 密封剂sealing gasket 密封垫片sealing ring 密封圈search light 探照灯seasick a.晕船seat n. 座seating n. 基座section n. 总段self excitation 自励self-designed a.自行设计的self-regulated device 自我调节机构semi-conductor n. 半导体SEMT of France 法国热机协会senior engineer 高级工程师sensibility n. 灵敏度separation n. 分离separator n. 分离器serialize vt.使……成系列service n. 公共基础设施service engineer 服务工程师service life 使用寿命service tank 日用柜servo motor 伺服电动机settle v. 沉淀settling tank 沉淀柜shaft bracket 艉轴架，人字架shaft system 轴系shape processing 成形加工shear machine 剪切机shed v. 放射，散发sheer n. 脊弧sheet plate 薄板shell n. 壳板shell plating 外壳列板shell structure 外板结构ship equipment 船舶结构ship general 总体ship outfitting 船舾ship system 船舶系统shipbuilding n. 造船shipbuilding industry 造船工业shipbuilding technology research institute 造船工艺研究所shipping n. 航运shipyard(yard)n. 船厂shop trial 车间实验shore electricity box 岸电箱short circuit 短路short wave 短波short-range a.短途的shot-blast v. 喷丸shot-blasting 喷丸处理side n. 船侧side girderside light 舷灯side plate 弦侧板side structure 船侧结构signal n. 信号signal light 信号灯signal processor 信号处理器silicon n. 硅silicon control rectifier(SCR)可控硅single bottom 单底single-action a.单作用single-rudder n. 单舵single-stage n. 单级single-screw n. 单桨site architect 现场造船师site supervisor 现场监控师sketch n. 草图slide-block n. 滑板，导块sliding distance 滑行距离slipway n. (倾斜)船台slipway taper 船台斜面small metacentric angle 小倾角socialist market economy 社会主义市场经济software n. 软件soil n. 土壤SOLAS 国际海上人命安全公约SOS 遇难信号sound energy 声能sound insulation 隔音sound power telephone 声力电话sound speed 声速sound wave 声波sounder n. 测深仪sources of power supply 能源space n. 舱室space n. 空间spare gears 备品spare parts(spares)备件special power supply 特种电源speed indicator 航速指示器speed reduction 减速speed servo system 速度随动系统spring n. 弹簧squeeze n. v. 挤压stability n. 稳性stabilizer n. 减摇鳍stabilizing unit 减摇装置staff member 职员stage n. 级stainless steel 不锈钢stand v. 经受standard n. 标准standard displacement 标准排水量stand-by n. 备用stand-by generating set 备用发电机starboard n. 右舷start v. 动身，出发starting system 起动系统starting valve 启动阀state v. 说明state-specified a.部颁的station v. 驻扎steadiness n. 稳定性steam &aux. boiler system 蒸汽与副锅炉系统steel plate pretreatment 钢板预处理steel structure 钢结构steel wire 钢丝steering gear 操舵装置steering gear 舵机steering gear room 舵机房steering mechanism 操舵机构steering wheel 舵轮stem n. 艏柱stern n. 船艉，艉柱stern tube 艉轴管stiffener n. 扶强，加强筋storage tank 贮存柜store-room n. 储藏室straight line 直线straight seam 直焊缝strength test 强度试验stringer n. 纵通材structural material 结构材料structure n. 结构，构件stud n. 螺柱stuffing box 填料函subway shield 地铁盾构suck v. 吸入suction (induction) stroke 汲气冲程suction port 吸入口sufficient a.足够的，充足的sum n. (数)二树之和supercomputer n. 巨型（计算）机superstructure n. 上层建筑supervision n. 监督,监造supply vessel 补给，工作船support n. 支撑物surface treatment 表面处理surveyor n. (船)验船师survive v. 幸存，死里逃生sustain v. 支撑，支持swirl chamber 涡流式燃烧室swirl resistance 涡流式阻力switch n. 开关symbol n. 符号symmetrical a.对称的synchro (selsyn)n. 自整角机synchro signal transmitter 自整角机讯号发送器synchronous device 同步装置synchronous follower 同步随动件talent n. 人才，有才能的technical staff 全体技术人员technical force 技术力量technical service 技术服务technical specification (spec)技术规格书technical term 技术术语telegraph n. 传令钟teleprinter n. 电传打字机teleperature relay 温度继电器temporarily adv. 临时地temporary emergency power supply 临时应急电源terminal n. 终端testing n. 调试testing facilities 测试设备testing instrument 测试仪器test & trials 试验与试航TEU reefer container ship 冷风集装箱船the ambient air 大气the application software 应用软件the block coefficient 方型系数the brake horse power (BHP) 轴马力，制动马力the breath moulded 型宽the central processing unit (CPU) 中央处理单元the centralized control room (the control room)集控室the controllable pitch propeller (CPP)可调螺距桨the critical path method (CPM) 各种计划节点配合the data base management system (DBMS)数据库管理系统the depth moulded 型深the design water plane 设计水线面the design water plane coefficient 设计水面线系数the displacement coefficient 排水量系数the earth magnetic field 地球磁场the effective horsepower 有效马力the fire main 消防总管the fixed pitch propeller 固定螺距桨the future type 未来型the graphic processing software 图像处理软件the intertia navigation system 惯性导航系统the integral stud anchor chain 整体锚链the language system 语言系统the length B.P.两柱间长the length overall 全长the length W.L.水线长the living quarters 生活区the longitudinal prismatic coefficient 纵向菱形系数the metacentre of transversal inclination 横倾稳心the middle longitudinal cross section 舯横剖面the midship transversal cross section coefficient 舯横截面系数the net registered tonnage 净登记吨位the North Pole 北极the office automation (OA)办公自动化the operating system (OS)操作系统the painting outfitting 涂装the parties concerned 有关方面the propulsion plant 推进装置the rated frequency 额定功率the rated horsepower 额定马力the roll period 横摇周期the satellite navigation system 卫星导航系统the system software 系统软件the total longitudinal bend 总纵弯曲the total longitudinal strength 总纵强度the total tonnage 总吨位thermal mechanism 热力机械thermal stress 热应力thermometer n. 温度计thread v. 攻螺纹thrust bearing 推力轴承thrust end 推力端thrust ring 推力环thrust shaft 推力轴thyristor n. 硅可控整流器，可控硅tier n. （船）层TIG钨极惰性气体焊tightness test 密性试验time vt. 确定……的时间timing gear 准时机构title n. 职称，头衔tonnage n. 吨位top people 上层人物top side plate 弦侧顶板torsional vibration 扭振torsional moment 扭距TQC全面质量管理transceiver n. 收发报机transfer pump 输送泵transistor amplifier 晶体管放大器transistor controller 晶体控制器transistor loop 晶体管回路transmitter n. 发射机,发送器transportation n. 输送transversal a. 横向的transversal bulkhead 横隔舱壁transversal scavenge 横流扫气transversal stability 横稳性treatment plant 处理装置trend n. 趋势trial-and-error a.反复的通过试验找出错误的trim n. 纵倾trunk-piston n. 筒形活塞T-type joint T型接头。
船舶专业术语英语翻译
leveler 调平器，矫平机
life saving appliance 救生设备
lifebuoy 救生圈
lifejacket 救生衣
lift fan 升力风扇(翻译公司)
lift offsets 量取型值
light load draft 空载吃水
liquid chemical tanker 液体化学品船
list 倾斜
living and utility spaces 居住与公用舱室
Lloyd’s Register of shipping 劳埃德船级社
Lloyd’s Rules 劳埃德规范
Load Line Convention 载重线公约
landing craft 登陆艇
launch 发射，下水
ห้องสมุดไป่ตู้
launch 汽艇
launching equipmeng (向水中)投放设备
LCC 大型原油轮
leading edge 导缘，导边
ledge 副梁材
length overall 总长
lightening hole 减轻孔
light-ship 空船
limbers board 舭部污水道顶板
liner trade 定期班轮营运业
lines 型线
lines plan 型线图
Linnean hierarchical taxonomy 林式等级式分类学
mast 桅杆
mast clutch 桅座
matrix 矩阵
merchant ship 商船
Merchant Shipbuilding Return 商船建造统计表
船舶常用英语
船舶常用英语 船舶类型常用英语liner定期货船tramp ship 不定期货船ship, vessel boat, craft sampan船，船舶艇舢 板 , 小 船 container ship container ship ship集装 箱船 full-全集装箱船 semi-container半集装箱船 multi-purpose containermanpowered boat 人力船ship 多用途集装箱船sailor; sailing boat sailor ship帆船 motor机帆船 power-driven机动船 paddle steamer, paddlegeneral cargo ship/vessel/carrier (cargo) carrier ore carrier杂 货 船 bulk散货船矿砂船wheel vessel 明 轮 船 screw ship; propeller vessel grain carrier 运粮 船 coal螺旋桨船 airscrew ship; aerial propeller vessel 螺旋桨船空气 carrier; coaler carrier运煤船 lumber(timber) 运 木 船 cattle carrierhovercraft; aircushion craft 气垫船 hydrofoil运牲畜船 multi-purpose ship 多用途船水翼船hydrojet propelled boat, water jet boat 喷水船 liquid cargo ship tank 液体货货船 chemical化学品液货船 liquid chemical steamship; steamer 蒸汽机船 motor tanker液 体 化 学 品 船 liquefied gas carriership内燃 机船 diesel ship液化气体船 liquefied petroleum gas tanker (LPG) 液 柴油机船 electrically-propelled ship电力推进船化石油气运输船steam turbine ship 汽轮机船 gas turbineliquefied natural gas tanker (LNG) 液化天然气运输船 ship 核动力船 燃气轮机船 nuclear-power shiptanker; oil tanker tanker 油轮 super超级油轮 VLCC (verydeck ship flush deck ship quarter-deck ship 半舱船 single side ship 甲板船平甲板船 raised尾升高甲板船 well-deck ship单舷长大舱口船 large crude carrier) (吨位在 20 万至 30 万吨之间的)巨型油轮ULCC (ultra-large crude carrier) (吨位在 30 万至 50 万吨之间的) 超巨型油船 three-island ship 三岛式船 doublerefrigerated ship; cold storage ship冷 藏 船 roll- shell ship riveted ship welded shiptransversely framed ship longitudinally framed ship 双壳船铆接船 焊接船横 骨 架 式 船 纵骨架式船 combinedon/roll-off ship (RO/RO ship) ferry ferry 货物渡船 fishing vessel(boat)trawler 滚装船 渡船 passenger旅 客 渡 船 freight ferry渔轮拖网渔轮 barge framed ship 混合 骨 架 式 船 sea-going vesselcarrier; lighter aboard ship(LASH)载驳船海船 ocean-going vesselcoaster ship 远洋船沿海船 channel海峡船 inland waterwaybarge; lighter甲板驳 well-deck barge double shell barge 驳船 deck barge半舱驳双壳驳 single sidevessel 民用船；商船 transport ship yacht 内河船 civil ship; merchant ship运输船 pleasure 游艇 passenger shipbarge 油驳 container barge RO/RO barge gas barge 单 舷 长 大 舱 口 驳 oil barge集装箱驳船 滚装驳船 liquefied液化 气 体 驳 hopper barge客船coasting passenger and cargo ship 沿海客货船开底泥驳 split hopper bargepusher; pushboat ship对开泥驳顶推船；推船 working工程船passenger and auto-car carrier 旅客及汽车运输 tug; tugboat; towboat 拖船 harbor tugcutter suction dredger 绞吸挖泥船bucket winter load line(W) 冬季载重线wheel dredger 斗轮挖泥船bucket dredger winter North Atlantic load line(WNA) 冬季北大西洋链斗挖泥船reclamation craft 吹泥载重线船even keel （首尾）等吃水，平载grab dredger dredger抓斗挖泥船dipper铲斗挖泥船floating pitter;extreme breadthfloatable length最大宽度可浸长度drive pitter 打桩船floating crane; derrick sheer at forward (after) perpendicular 首尾舷弧boat 起重船floating dock sheer line 舷弧线浮船坞cable layer; cable ship scientific surveying ship布缆船科学考察船researchaccommodationaccommodation deck居住舱室起居舱室；旅客甲板ship 科学调查船oceanographic accommodation ladder 舷梯research vessel 海洋调查船accommodation ladder platform 舷梯平台surveying ship ice-breaker 测量船破冰船accommodation ladder manrope 舷梯扶索after body后（部船）体pontoonhigh speed craft 浮舟;浮桥;趸船, 浮码头高速船after peak bulkheadpeak tank艉尖舱舱壁after艉尖舱passenger catamaran vehicle ferry catamaran双体客船双体车辆渡船air holeair pipe空气孔空气管appendagevehicle-passenger ferry catamaran 双体车客渡船（船体水线下的）附体；附件pontoon catamaran二、center line双体趸船船舶结构常用英语中心线，中线auxiliary machinerybalanced rudder压载（物）ballast line系ballast pump辅助机械；辅机平衡舵ballast压载水管压载水泵athwartships 横对船体（与船首尾线直交）ballast pumping system 压载水系统bevel base line amidships斜角；斜面基线在船中部；在纵中线上ballast tank(water)battenbatten-ceiling压载舱（水）板条；压条（封仓用）（货舱内）护舱条，护板designed waterline breadth designed waterline length draftformer/aft draft 设计水线宽设计水线长吃水首/尾吃水beambeam bracket交合线，榫（艏柱或艉柱上）bending moment横梁梁肘板bearding弯矩draft figures intersection吃水尺度交点；交叉；横断面bilgebilge bracket舭部；舱底；（船底）污水沟舭肘板knucklelength between perpendicular折角线垂线间长bilge keel(chock, piece)舭肘板舭龙骨bilge kneelength overallwaterline length 满载水线长总长load bilge linebilge main舭水管系舭水总管register length (breadth; depth) 度）freeboardrise of floor (dead; rise) 登记长度（宽度、深干舷舭高；船底loadlinebilge pipe (suction)bilge pumpstrake(plate)bilge well舭吸水管舭水泵bilge舭列板污水井bittmark 载重水线标记系缆桩bollard 系缆桩；系船柱；双系柱fresh water load line (F.) 淡水载重线bolster 枕垫fresh water timber load line (L.F.) 淡水木材载重线bonnet 烟囱帽；机罩tropical fresh water load line (TF) 热带淡水载重线boom 杆；吊杆；桁；叉架tropical load line (T) 热带载重线boom crutch(support; rest) 吊杆支架summer load line(S) 夏季载重线bossing 尾管突出部；轴包套bottom summer freshwater load line(F) 夏季淡水载重线frame 船底横骨bottomlongitudinal 船底板bowbow fender 船底纵骨bottom plate船首，船头艏护垫coamingcofferdamcollar platecollision bulkhead围板；舱口围板隔离舱封板船首舱壁；防撞舱壁bow flarebow thruster bracket breakwater bridgebulb angle bulbous bowbulb stern bulkhead bulkhead plating bulkhead stiffener bulwarkbulwark plating bulwark stay bunker tank bushingbuttbutt joint(seam) butt rivetingbutt welding butterfly clip bypass valve艏部外飘首侧推器肘板；（三角）拖架挡浪板桥；桥楼；驾驶台圆头角材球形船首，球鼻首球形船尾舱壁舱壁板舱壁扶强材舷墙舷墙板舷墙扶强材燃料舱衬套端接；残片平接缝对接铆对接焊蝴蝶夹旁通阀companion way(hatch)corrugated bulkheadcorrugationcross deck structurecrossing strength membercruiser sterncurtain platecut outdavitdeckdeck beamdeckhousedeck linedeck longitudinaldeck stringer(plate)deep tankderrickdiaphragmdouble bottomdoubling platedrain holeduct keel升降口槽形舱壁皱；槽形；波形舱间甲板结构交叉强力构件巡洋舰型船尾幕板开口；切吊艇架；吊艇柱甲板甲板横梁甲板室甲板线甲板纵骨甲板边板深舱吊杆隔板双层底双层焊合板排水孔箱形龙骨cable stopper camber camber of beam cant beamcant bracket cant frame cantilever capstancargo batten cargo block止链器翘曲梁拱斜梁斜角板斜肋骨悬臂梁绞盘；绞缆机货舱护板吊货滑车dunnagedunnage wooddynamic loadend bracketescape trunkengine bedengine casingescape scuttleescape ventexpansion joint垫舱（物料）；衬垫垫木动载荷端肘板（船内）应急通道机座机舱围壁（船内）应急出口脱险口伸缩接头cargo port 装货舷梯，舷门expansion trunk(tank) （油船）膨胀深井cat walk center girder center strake chafing plate chafing ring chain lock(well) chain pipe chain stopper chockclamp plate cleat （油轮上的）天桥，步桥中底桁中央内底板防擦板防擦环锚链舱锚链管止链器导缆器；垫木夹板，压板羊角；系绳铁栓；防滑条extension bracketface platefenderfender barfair leadflame screenflangeflanged bracketflat keelfloorfolding door延伸肘板面板碰垫；护舷材护舷条导缆器防焰罩折边折边肘板平板龙骨肋板折门forecastle deck fore peak tank艏楼甲板（船的）首舱；前尖舱hopperhopper tank漏斗；开舱泥驳底边舱forward perpendicular 首垂线hopper tank sloping plating 底边舱斜板horizontalfoundation frame 底座肋骨margin platehorizontal girder水平内底板水平桁frame number 肋骨跨数horizontal stiffener 水平扶强材（防挠材）frame space freeing port肋距甲板排水孔；放水孔hullhull construction船壳，船体船体结构gangway (gang ladder or gang board) 舷梯hull plating 船壳板gasket 垫圈，垫料（集）密封垫hull strength 船体强度general service pipe (G.S pump) 通用泵，总用泵inner bottom 内底girdergooseneck(parity iron) gratingground tackle gunwalegunwale angle gunwale bar gunwale railing gunwale tank gussetgutter桁材鹅颈头；吊杆弯头格子板；滑铁板锚泊索具舷缘；舷边舷边角钢舷边角材舷边栏杆舷侧水柜（甲板下）角板；扣板（甲板）水沟；槽沟inner bottom platinginsert platejackjack ladderJacob's ladderJoggled jointjoggling machinekeelkeelblockkeel linekeel plate内底板嵌板；衬板千斤顶绳梯软梯；绳梯折接；弯合折曲机龙骨龙骨墩龙骨线；艏艉线龙骨板gutter angle; waterway angle （舷侧）排水沟角钢keel rail （救生艇）艇底把手gypsy handrail 绞筒（锚机绞车上的）舷墙扶手keelsonkingpost内龙骨起重柱；将军柱hanging rudder; hinged rudder hatch; hatchway; hatch opening hatch bar 吊舵；悬舵舱口封舱压条kneeknee of the decklightening hole肘板；弯头甲板梁肘板减轻孔hatch batten hatch beam (web) hatch booby hatch coaming hatch cover hatch end beam 舱口边压条舱口大梁活动舱口盖舱口板舱口盖舱口端梁lignum vitaelocal strengthlocal stresslongitudinalbulkheadlongitudinal bending铁梨木局部强度局部应力纵骨；纵材；纵桁longitudinal纵舱壁纵向弯曲hatch moulding hatch side girder hatch tarpaulin hatch trunk hawse pipe hawserheel舱口椽材舱口纵桁盖舱布舱口围阱锚链管绳索；大缆踵材；横倾longitudinal framing systemlongitudinal strengthlugmain deckframe人孔man hole doorman hole coaming纵骨架式纵向强度耳板主甲板main主肋骨manhole人孔盖人孔围板moment ofhinged cover(door) holdhold beamhold framehold ladderhold stanchion(pillar) hold stringer 铰链盖（门）货舱舱内梁舱内肋骨舱内梯舱内支柱舱内纵桁inertiamargin platemolded breadthmolded depthmooring holepostmud box惯性矩内底边板型宽型深导缆孔mooring系缆柱；岸柱泥箱non-return valvenon-watertight bulkhead notchoscillating load parallel middle body panel stiffenerpanting arrangement panting beampanting stringer止回阀非水密舱壁切口；槽口；刻痕振动负荷平行中体板格扶强材防挠振结构防挠振梁防挠振纵桁scupperscupper pipescuttleseamsectionmodulusruddershaftshaft bracket排水孔排水管舷窗；人孔（盖）；小舱口盖焊缝；接缝剖面section剖面模数semi-balanced半平衡舵轴轴架pillar 支柱；墩shaft tube; stern tube 艉轴管pintle 舵销shaft tunnel(alley; passage; trunk) 轴隧；地轴弄plane bulkheadplane keelpump roomhelm(rudder) pintle horizontal margin plate plating平台platingplimsoll markpoop平面舱壁平板龙骨泵舱舵销水平内底边板out bottom外底板platform壳板载重线标志艉楼；船尾shedder platesheersheer strakeshellshell frameshell platingshell strake; outside platingshelter deckshifting beam泄板；斜板舷弧；偏航舷顶列板船壳；壳舷侧肋骨船壳板；外板船体外板遮蔽甲板活动舱口梁poop deck 艉楼甲板shifting board (or plank) 止移板（散装谷类）；防动port 舷门；舱门；（装货）口；窗；门；孔板portholepropeller; propellor propeller aperture propeller boss(bub) propeller shaft rackingrailrollinground of beam sternrudderrudder carrier casing舵针；舵栓舷窗；（装货）舷门推进器；螺旋桨螺旋桨空间螺旋桨毂艉轴（船体）横向挠度扶手；栏杆横摇梁拱round圆（船）尾舵舵托rudder舵杆管rudder pintleside girderside longitudinalside platingside strakesingle bottomskidskylightslanting plate污油水舱sloping platesloping plate longitudinalslotsluicesluice valve旁桁材舷侧纵骨舷侧外板舷侧列板单层底护舷木；垫板天窗斜板slop tank斜板斜板纵骨槽；开缝水密门；水闸闸阀rudder plate; rudder blade rudder postrudder stock 舵叶；舵板舵柱舵杆sniped endsoft toesolid floor削斜端软趾实肋板rudder trunk rung scallop scantling舵杆围壁；舵杆管（梯子）踏步；横档扇形开孔构件尺寸sounding pipestabilizerstabilizing tankstaging测量管；测深管减摇装置减摇水舱构架；台架；脚手架scantling of the structure 结构尺寸stanchion 支柱；栏杆柱scarf; scarph scarf joint scarf weld scarfing bracket 嵌接处；斜面；斜接斜（嵌）接（斜面）焊接嵌接肘板static loadstaystay bar(or rod)stay plate静载荷支柱；撑条；支索撑杆撑板stemstem poststernstern counterstern shaft; propeller shaft stern poop 艏；艏柱；艏材艏柱船尾，艉部船尾突出体艉轴艉楼upper (lower) shelf plateupper (lower) stoolventilatorvertical ballast trunkvertical girderwarping chocks上（下）支架板上（下）托架通风筒竖向压载通道竖桁滚轮导缆钳stern post stiffener stool strake尾柱防挠材；扶强材；加固物托架，座，凳列板wash bulkheadwatertight bulkheadwatertight deckweather deck可荡舱壁，挡水舱壁水密舱壁水密门露天甲板strength calculation 强度计算web beam 强横梁，桁板横梁strength deck 强力甲板web frame 加强肋骨，框架肋骨，桁板肋骨stringer stringer plate structural member structural strength strum boxstrutstuffing box superstructure tail (end) shaft tarpaulin纵桁甲板边板构件结构强度（舱底水）过滤箱撑材，支柱，轴架填料箱上层建筑艉轴防水油布，帆布，舱盖布web platewedgewinchwinch-headwindlasswing tankwire clipwire reel三、腹板楔木，楔子起货机绞车卷筒起锚机翼舱，翼柜钢缆夹卷缆车，钢丝滚筒船舶材料及工艺常用英语thrust bearing(block) 推力轴承 A. Shipbuilding material (造船材料)thrust shaft collars tieplatetopside tank推力环带板，牵板，连接板顶边舱；上边柜T-barZ-barI-BarT 型钢Z 型钢工字钢topside tank sloping plating torsion 顶边舱斜板扭转channel barangle steel槽钢角钢torsion strength transom stern transverse扭转强度方形船尾横梁，横材equal angle steelunequal angle steeloffset bulb plate等边角钢不等边角钢球扁钢transverse bulkhead transverse frame横舱壁横肋骨，横框flat plateround steel钢板圆钢transverse framing system 横骨架式half round steel 半圆钢transverse ring transverse strength tripping bracket横环横向强度防倾肘板steel pipealloy steelspecial steel钢管合金钢特种钢tween deck tween deck frame twisting distortion中间甲板甲板间肋骨扭转变形tempering steellow carbon steelhigh tensile steel回火钢材低碳钢高强度钢twisting moment tunnel扭转力矩轴隧，隧道，风筒copperbrass紫铜黄铜tunnel escape tunnel shaft bearing轴隧应急出口中间轴支撑轴承aluminum alloystainless steel铝合金不锈钢ullage pipe (port) 油位测定管（孔）mechanical property 机械性能ullage spaceupper deckupper (reverse) frame 空挡空间上甲板内底横骨tensile testbend testimpact test拉伸试验弯曲试验冲击试验torsion test 扭转试验hairline fracture 发式裂纹torsion strength 抗扭强度buckling 皱折torsional deflection 扭转；扭转变形deformation 变形tensile strength 拉伸强度deflection, deflexion 挠曲yield strength 屈服强度flexion 弯曲yield point 屈服点lamellar tearing 层间撕裂yield stress 屈服应力rust 铁锈elastic limit 弹性极限scale 锈皮ultimate strength 极限强度pitting 点蚀，锈斑ultimate tensile stress 极限拉伸应力indent 凹痕，凹陷elasticity 弹性groove 槽沟ductility 延展性，可塑（锻）性detachment 脱开，脱焊flexibility 挠性，柔性，易弯性rupture 断裂，破裂toughness brittleness friability hardness 韧性脆性易碎性硬度croppingrenewaldescalegrind割掉换新除锈磨平rigidity 刚性，稳定性be veed out 刨除heat treatment 热处理alignment 对准，校直quench 淬火snip 剪断，剪片normalising annealing正火退火taper 削斜，斜度B. Shipbuilding workmanship （造船工艺）hardening tempering casting forging pickling ship timber硬化，淬火回火铸件，铸造锻件，锻造酸洗船用木材Working drawingend elevationfront elevationside elevationplanelines plan施工图后面图正面图侧面图平面图型线图lignumvitae 铁梨木plan of waterlines 水线图three-plywood 三夹板general arrangement plan 总布置图asbestos 石棉construction plan 结构图asbestos cloth 石棉布damage plan 损坏示意图asbestos board 石棉板shell expansion plan 外板展开图asbestos sheet asbestos cord 石棉纸石棉绳docking planframing plan进坞图船体构架图asbestos paint fiberglass石棉涂料玻璃丝inboard profile planmidship section plan纵剖面图舯剖面图plastics 塑料loaded waterline plane 满载水线图resin rubber树脂橡皮half breadth planstowage plan半宽水线图配载图painting 油漆cladding 镀层，表面处理laying off loftingmold loft floor放样放样台coating 涂层，敷料mold loft 放样间corrosion 腐蚀，侵蚀template 样板wastage 损耗，蚀耗mold loft batten, template batten 木样条wear and tear 蚀损，磨损evolute 展开线fracture 裂纹allowance 余量fatigue fracture 疲劳裂纹assembly 装配subassembly 分段装配subdivision length 分段长度pressure testflooding test压力试验灌水试验shipbuilding tolerance 造船公差hose test 冲水试验building berth building dock 船台干坞oil tight testpurchase trial油密试验交船试验slip dock 湿坞marine slipway, railway dry dock 船排四、船舶性能常用英语marine slipway cradle 船排支架angle of vanishing stability 稳性消失角building block, stocks 枕木buoyancy 浮性launch 下水buoyancy curve 浮力曲线launching ways 下水滑道capsizing lever, upsetting lever 倾覆力臂launching grade 下水坡度capsizing moment, upsetting moment 倾覆力矩launching cradle 下水架center of buoyancy 浮心end launching 纵向下水center of floatation 漂心side way launching 横向下水center of gravity 重心hydraulic press 水压机curve of areas of waterplanes 水线面积曲线flanging machine 折边机curve of section areas 横剖面面积曲线plate bending machine 弯板机curve of volumes of displacement 排水量曲线angle cutter 角钢切断机dynamical stability（curve）动稳性（曲线）planing machine shearing machine 刨边机剪床entrance anglefloodable length进水角可浸长度guillotine shear 龙门剪床force of buoyancy, buoyant force 浮力oxy-acetylene welding 氧-乙炔焊free surface 自由液面co 2 gas welding 二氧化碳气体焊heaving 垂荡arc welding 电弧焊heeling angle 横倾角unionmelt welding 埋弧自动焊heeling moment 横倾力矩fusion welding 熔焊hogging 中拱fillet welding 角焊hogging condition 中拱状态flat seam 对接缝hogging moment(stress) 中拱力矩（应力）butt joint welding intermittent welding 对接焊间断焊；断续焊hydrostatic curvesinitial metacenter静水力曲线初稳心staggered intermittent welding 交错断续焊缝initial stability 初稳性lap weld 搭接焊insubmersibility 抗沉性slot weld 槽焊；长孔焊longitudinal inclination; list; heel 纵倾plug weld 塞焊；圆孔焊longitudinal stability 纵稳性run of welding 焊道panting （波浪对船体的）冲击welding torch 焊炬period of rolling 横摇周期welding rod 焊条pitching 纵摇flux 焊药pounding 波浪冲击filler metal; deposited metal 熔敷金属maneuverability 操纵性welding stress welding procedure 焊接应力焊接方法margin linemetacenter限界线稳心welding throat 焊喉moment to change trim one centimeter 每厘米纵倾cutting torch 割炬力矩acetylene generator 乙炔发生器permissible length 许可长度slag 熔渣potential head 势头undercut （焊接）咬边；根切pressure head 压头hydraulic test 水压试验restoring moment, righting moment 复原力矩restoring lever, righting lever 复原力臂unworkable, inoperable 指本身不能工作，rolling 横摇在损坏状况判断中不能使用sagging 中垂17. out of function 不能工作，失去作用，不sagging condition 中垂状态起作用sagging moment(stress) 中垂力矩（应力）18. unserviceable (useless) 不能使用（指必须seaworthiness 适航性换新的损坏部件）stability 稳性19. could not be started(failed to start) 不能stability at large angles 大倾角稳性启动stability criterion numeral 稳性横准数20. empty 空的static head 静压头（力）21. fitted incorrectly 安装不正确（指小型statical stability (curve) 静稳性（曲线）的装置设备）surging swaying 纵荡横荡installed incorrectly的装置设备）安装不正确（指较大tons per centimeter of immersion 每厘米吃水吨数22. dangerous accumulation of inflammable total head (pressure) 总压头（力）vapors 可燃气体危险集积transverse inclination, trim 纵倾it was obvious that this state had existedfor atransverse (longitudinal) metacentertransverse (longitudinal) stability横（纵）稳心横（纵）稳性considerable time期存在的（损坏）状况是长trim by the bow (stern) 首（尾）倾23. sluggish in (action, answering) （动作、应turning quality (circle) 回转性（圈）答）迟钝velocity head 速头 B. Deficienciesweigh curve 重力曲线 1. no…fitted, no…provided 未装yawing 艏摇 2. no…available3. missing 未备有遗失五、船体检验常用英语 4. incomplete 不齐全，不完整THE DESCRIPTION OF DAMAGE A. General descriptions 5. deficient6. insufficient不足，缺少不足1. in good condition2. in poor condition3. in bad condition情况良好情况欠佳情况不佳，情况不良7. neglected8. omitted9. removed遗漏遗漏，省去移开，拆走4. in a neglected condition 缺乏保养10. washed overboard 冲走5. not properly serviced 未经正常保养6. not properly cleaned 未经正常清洁7. not properly protected 未经正常保护11.12.droppedfitted with wrong ….(size, material, devices…)跌落错用（尺8. not properly insulated 未经正常隔热（或电气绝缘）寸，材料，仪器）C. Tightness, stains, loss of etc.9. not properly adjusted 未经正常校正 1. Leaking 漏10.11. defectivedamaged有缺陷的（失效）损坏2. infiltrating (seeping)3. weeping渗漏泪滴damaged beyond repair 损坏了无法修 4. sweating5. not watertight汗滴不水密12.13. failed (in failure)cut of order (in trouble)失效故障6. loss of watertightness7. loss of airtightness失去水密性（比 5 好）失去气密性out of action 停止工作（作用），不是指故8. loss of oiltightness9. escaping of cool 失去油密性逃冷14. in disorder 零乱（船属具零乱了）10. loss of lub-oil pressure 滑油压力降低13.14. oil soakedwater soaked油浸水浸车E. Corrosion, seizing, choking etc.15.16.17.18.19. water stainedoil stainedrust in patchesverdigris in patcheswater marks水渍油渍锈斑铜绿斑水渍1. corrosion2. wasted3. deteriorated4. thinned5. pitted腐蚀耗油蚀薄变薄麻点D. Crack, score, break etc.1. scuffed 拉毛（仅从反光上可观察到）6. eroded7. rusted侵蚀生锈2. chafed3. scored擦痕拉痕（痕较chafed 深）8. rotten9. decayed（木、橡胶）腐烂、腐坏（电缆）腐烂、腐坏4. scratched 抓痕（硬拉过的痕）10. aerated（橡胶、电缆）腐烂、腐坏5. scraped6. grooved7. ridged8. cracked hair crack 刮痕（长期运行刮的痕）槽痕（比pitting 深）凸起雷治痕（环状的痕）裂痕发痕11. aged12. seized13. seized by corrosion14. stuck15. rust-jammed老化咬住锈死（粘）咬住锈轧surface crack 表面裂痕16. fouled 拥塞through crack 穿透裂痕17. clogged 堵塞（常指管子的堵塞）non-through crack 9. chapped 未穿透裂痕龟裂，折裂18. blocked19. gagged阻塞塞口10. fractured 折裂20. foul & dirty 闭塞11. broken off 破掉（破裂后跌落）21. blanked 封没broken 破裂，破碎22. plugged 闭塞12. holed 穿洞23. choked 卡住，阻塞13. holed & flooded 破洞浸水 F. Wear, loose, clearance etc.14.15.16.17.18.19. openedbentcantedbuckledwarpedindented (dented)开口弯曲倾斜皱折翘起，翘曲凹痕，凹陷（指船壳板1. Loose2. starting3. slackslack back4. worn5. worn cut evenly松动（铆钉）松动松动松出磨损均匀磨损在两档肋位间的凹陷） 6. worn cut unevenly 不均匀磨损20.21. set inwaved凹陷（指船壳板较大面积的凹陷）波曲7. worn on one side8. worn out symmetrically单边磨损对称磨损22. curled 卷曲（指绳索）9. distorted （轴线弯曲并扭转）扭曲23. rumpled 褶皱（指垫片）10. sprung （铆钉）扭歪24. bulged 鼓起，凸出11. twisted （轴线未弯、纯扭转）扭转25.26.27.28.29.30. collapsedrupturedtorn offtornpiercedpeeledburst倾陷，倾倒毁损撕破拉脱刺破剥皮（油漆剥落）爆破（指高压管路）12.13.14.15.16.17.18.excess clearanceexcess backlashexcess vibrationexcess noise levelloose engagementloose connectiontooth间隙过大齿隙过大振动过大噪音过大啮合太松接头松动齿31.32.33. blown off (packing)distortedengine break-down吹脱扭曲，歪扭因故障机器突然停worn outchopped offfractured磨损崩缺折断第10 页共12 页19. knockingknocking cylinder敲击敲缸8. faired9. faired on拷平原地拷平knocking valve gear knocking bearing 伐件敲缸轴承敲缸10.11.faired in placestraightened原地拷平拷直、校直20.21.22. bearing metaldetachedcrackedwipedbeltedoil groove blockedout off roundnessout off alignment轴承合金脱壳开裂铺铅熔化油槽堵塞失圆拉线不直12.13.14.15.16.17.18.19.dismantledisassembledstrippedunshippeddisconnectedopenedliftedjacked拆卸（某一零件）拆散（解体）拆除（某一部件）拆下断开（线、管接头）打开抬升、举起顶起（用千斤顶顶起）23.24. off-centeringdeflected偏心偏斜20.21.replaced (by, with)patch换用贴补G. Burning, heating, etc. B. Fit, scrape, grind etc.1. Sparking2. arcking (arcing)3. commutator scoredburntwornuneven sparking blackened roughmica undercut火花电弧整流器拉痕烧坏磨耗，磨损不平火花发黑粗糙弧坑1. fitted & scraped2. fitted & ground3. scraped & ground4. made to fit5. run to fit6. ground round7. ground smooth8. ground & reamed9. bored round10. planed smooth11. polished拂刮拂磨刮磨拂合（装配好）跑合（运动磨合）磨圆磨光磨绞镗圆刨光抛光4. brush set incorrectly 碳刷安装不正确12. machined 光车5. scorched6. coked7. charred8. overheated 烤焦结焦结碳过热13. skimmed14. finish machined15. rough machineC. Re-metal, adjust, check etc光刀精加工粗加工9. broken down10. short-circuit11. setting incorrect12. tripped incorrect击穿短路整定值不正确脱扣不正常1. Remetalled2. re-babbitted合金）3. pulled out重浇白合金重浇白合金（专指巴氏拉出13. batteriescompletely discharged（电）完全发光4. drawn out5. taken out抽出取出underchargedoverchargeddry waterA. Remove, crop etc.1. Removed2. removed & replaced未充满充电过量水干拆下拆装6. adjustedadjusted for alignmentadjusted trueadjusted for clearanceadjusted for centeringadjusted for deflection调整，校正校正拉线校正拉线校正间隙校中校偏3. removed, faired & replaced 拆装拷平7. checked 检查4. cropped & renewed 割换（管、板、栏杆）checked for roundness 检查圆度5. partly renewed 部分换新checked for insulation resistance 检查绝缘6. partly cropped & renewed 部分割换电阻7. cut off 割除第11 页共12 页checked for centering 检查中心位置checked for alignmentchecked for clearance 8. cleaned 检查拉线检查间隙清洁9. wire-scrubbed 钢丝刷（除锈）10. chipped & scraped 拷锈（油漆）11. measured & recorded 测量并记录12. logged (hourly)D. weld, rivet, wind etc.1.repaired by welding2.welded3.closed up by welds大）焊补4.built up by welds5.plug welded6.spot welded7.butt welded记录（小时）电焊修理补焊、焊接（面积、深度、高度较堆焊塞焊点焊对接焊8 tackweld 点焊、平头焊、定位焊第12 页共12 页。
船舶常用英语_一_
船舶常用英语一、船舶类型常用英语ship, vessel 船，船舶boat, craft 艇sampan 舢板, 小船manpowered boat 人力船sailor; sailing boat 帆船motor sailor 机帆船power-driven ship 机动船paddle steamer, paddle wheel vessel 明轮船screw ship; propeller vessel 螺旋桨船airscrew ship; aerial propeller vessel 空气螺旋桨船hovercraft; aircushion craft 气垫船hydrofoil 水翼船hydrojet propelled boat, water jet boat 喷水船steamship; steamer 蒸汽机船motor ship 内燃机船diesel ship 柴油机船electrically-propelled ship 电力推进船steam turbine ship 汽轮机船gas turbine ship 燃气轮机船nuclear-power ship 核动力船deck ship 甲板船flush deck ship 平甲板船raised quarter-deck ship 尾升高甲板船well-deck ship 半舱船single side ship 单舷长大舱口船three-island ship 三岛式船double shell ship 双壳船riveted ship 铆接船welded ship 焊接船transversely framed ship 横骨架式船longitudinally framed ship 纵骨架式船combined framed ship 混合骨架式船sea-going vessel 海船ocean-going vessel 远洋船coaster 沿海船channel ship 海峡船inland waterway vessel 内河船civil ship; merchant ship 民用船；商船transport ship 运输船pleasure yacht 游艇passenger ship 客船coasting passenger and cargo ship沿海客货船passenger and auto-car carrier 旅客及汽车运输船tourist ship; passenger carrier 旅游船cargo ship; freighter 货船cargo liner 定期货船tramp ship 不定期货船container ship 集装箱船full-container ship 全集装箱船semi-container ship 半集装箱船multi-purpose container ship 多用途集装箱船general cargo ship/vessel/carrier 杂货船bulk (cargo) carrier 散货船ore carrier 矿砂船grain carrier 运粮船coal carrier; coaler 运煤船lumber(timber) carrier 运木船cattle carrier 运牲畜船multi-purpose ship 多用途船liquid cargo ship 液体货货船chemical tank 化学品液货船liquid chemical tanker 液体化学品船liquefied gas carrier 液化气体船liquefied petroleum gas tanker (LPG) 液化石油气运输船liquefied natural gas tanker (LNG) 液化天然气运输船tanker; oil tanker 油轮super tanker 超级油轮VLCC (very large crude carrier) (吨位在20万至30 万吨之间的) 巨型油轮ULCC (ultra-large crude carrier) (吨位在30万至50万吨之间的) 超巨型油船refrigerated ship; cold storage ship 冷藏船roll-on/roll-off ship (RO/RO ship) 滚装船ferry 渡船passenger ferry 旅客渡船freight ferry 货物渡船fishing vessel(boat) 渔轮trawler 拖网渔轮barge carrier; lighter aboard ship(LASH)载驳船barge; lighter 驳船deck barge 甲板驳well-deck barge 半舱驳double shell barge 双壳驳single side barge 单舷长大舱口驳oil barge 油驳container barge 集装箱驳船RO/RO barge 滚装驳船liquefied gas barge 液化气体驳hopper barge 开底泥驳split hopper barge 对开泥驳pusher; pushboat 顶推船；推船working ship 工程船tug; tugboat; towboat 拖船harbor tug 港作拖船rescue tug 救助拖轮salvage ship 救捞船dredger 挖泥船trailing suction dredge 耙吸挖泥船cutter suction dredger 绞吸挖泥船bucket wheel dredger 斗轮挖泥船bucket dredger 链斗挖泥船reclamation craft 吹泥船grab dredger 抓斗挖泥船dipper dredger 铲斗挖泥船floating pitter; drive pitter 打桩船floating crane; derrick boat 起重船floating dock 浮船坞cable layer; cable ship 布缆船scientific surveying ship 科学考察船research ship 科学调查船oceanographic research vessel 海洋调查船surveying ship 测量船ice-breaker 破冰船pontoon 浮舟; 浮桥; 趸船, 浮码头high speed craft 高速船passenger catamaran 双体客船vehicle ferry catamaran 双体车辆渡船vehicle-passenger ferry catamaran 双体车客渡船pontoon catamaran 双体趸船二、船舶结构常用英语center line 中心线，中线athwartships 横对船体（与船首尾线直交）bevel 斜角；斜面base line 基线amidships 在船中部；在纵中线上designed waterline breadth 设计水线宽designed waterline length 设计水线长draft 吃水former/aft draft 首/尾吃水draft figures 吃水尺度intersection 交点；交叉；横断面knuckle 折角线length between perpendicular 垂线间长length overall 总长load waterline length 满载水线长register length (breadth; depth) 登记长度（宽度、深度）freeboard 干舷rise of floor (dead; rise) 舭高；船底loadline mark 载重水线标记fresh water load line (F.) 淡水载重线fresh water timber load line (L.F.) 淡水木材载重线tropical fresh water load line (TF) 热带淡水载重线tropical load line (T) 热带载重线summer load line(S) 夏季载重线summer freshwater load line(F) 夏季淡水载重线winter load line(W) 冬季载重线winter North Atlantic load line(WNA) 冬季北大西洋载重线even keel （首尾）等吃水，平载extreme breadth 最大宽度floatable length 可浸长度sheer at forward (after) perpendicular 首尾舷弧sheer line 舷弧线accommodation 居住舱室accommodation deck 起居舱室；旅客甲板accommodation ladder 舷梯accommodation ladder platform 舷梯平台accommodation ladder manrope 舷梯扶索after body 后（部船）体after peak bulkhead 艉尖舱舱壁after peak tank 艉尖舱air hole 空气孔air pipe 空气管appendage （船体水线下的）附体；附件auxiliary machinery 辅助机械；辅机balanced rudder 平衡舵ballast 压载（物）ballast line 压载水管系ballast pump 压载水泵ballast pumping system 压载水系统ballast tank(water) 压载舱（水）batten 板条；压条（封仓用）batten-ceiling （货舱内）护舱条，护板beam 横梁beam bracket 梁肘板bearding 交合线，榫（艏柱或艉柱上）bending moment 弯矩bilge 舭部；舱底；（船底）污水沟bilge bracket 舭肘板bilge keel(chock, piece) 舭龙骨bilge knee 舭肘板bilge line 舭水管系bilge main 舭水总管bilge pipe (suction) 舭吸水管bilge pump 舭水泵bilge strake(plate) 舭列板bilge well 污水井bitt 系缆桩bollard 系缆桩；系船柱；双系柱bolster 枕垫bonnet 烟囱帽；机罩boom 杆；吊杆；桁；叉架boom crutch(support; rest) 吊杆支架bossing 尾管突出部；轴包套bottom frame 船底横骨bottom longitudinal 船底纵骨bottom plate 船底板bow 船首，船头bow fender 艏护垫bow flare 艏部外飘bow thruster 首侧推器bracket 肘板；（三角）拖架breakwater 挡浪板bridge 桥；桥楼；驾驶台bulb angle 圆头角材bulbous bow 球形船首，球鼻首bulb stern 球形船尾bulkhead 舱壁bulkhead plating 舱壁板bulkhead stiffener 舱壁扶强材bulwark 舷墙bulwark plating 舷墙板bulwark stay 舷墙扶强材bunker tank 燃料舱bushing 衬套butt 端接；残片butt joint(seam) 平接缝butt riveting 对接铆butt welding 对接焊butterfly clip 蝴蝶夹bypass valve 旁通阀cable stopper 止链器camber 翘曲camber of beam 梁拱cant beam 斜梁cant bracket 斜角板cant frame 斜肋骨cantilever 悬臂梁capstan 绞盘；绞缆机cargo batten 货舱护板cargo block 吊货滑车cargo port 装货舷梯，舷门cat walk （油轮上的）天桥，步桥center girder 中底桁center strake 中央内底板chafing plate 防擦板chafing ring 防擦环chain lock(well) 锚链舱chain pipe 锚链管chain stopper 止链器chock 导缆器；垫木clamp plate 夹板，压板cleat 羊角；系绳铁栓；防滑条coaming 围板；舱口围板cofferdam 隔离舱collar plate 封板collision bulkhead 船首舱壁；防撞舱壁companion way(hatch) 升降口corrugated bulkhead 槽形舱壁corrugation 皱；槽形；波形cross deck structure 舱间甲板结构crossing strength member 交叉强力构件cruiser stern 巡洋舰型船尾curtain plate 幕板cut out 开口；切davit 吊艇架；吊艇柱deck 甲板deck beam 甲板横梁deckhouse 甲板室deck line 甲板线deck longitudinal 甲板纵骨deck stringer(plate) 甲板边板deep tank 深舱derrick 吊杆diaphragm 隔板double bottom 双层底doubling plate 双层焊合板drain hole 排水孔duct keel 箱形龙骨dunnage 垫舱（物料）；衬垫dunnage wood 垫木dynamic load 动载荷end bracket 端肘板escape trunk （船内）应急通道engine bed 机座engine casing 机舱围壁escape scuttle （船内）应急出口escape vent 脱险口expansion joint 伸缩接头expansion trunk(tank) （油船）膨胀深井extension bracket 延伸肘板face plate 面板fender 碰垫；护舷材fender bar 护舷条fair lead 导缆器flame screen 防焰罩flange 折边flanged bracket 折边肘板flat keel 平板龙骨floor 肋板folding door 折门forecastle deck 艏楼甲板fore peak tank （船的）首舱；前尖舱forward perpendicular 首垂线foundation 底座frame 肋骨frame number 肋骨跨数frame space 肋距freeing port 甲板排水孔；放水孔gangway (gang ladder or gang board) 舷梯gasket 垫圈，垫料（集）密封垫general service pipe (G.S pump) 通用泵，总用泵girder 桁材gooseneck(parity iron) 鹅颈头；吊杆弯头grating 格子板；滑铁板ground tackle 锚泊索具gunwale 舷缘；舷边gunwale angle 舷边角钢gunwale bar 舷边角材gunwale railing 舷边栏杆gunwale tank 舷侧水柜（甲板下）gusset 角板；扣板gutter （甲板）水沟；槽沟gutter angle; waterway angle （舷侧）排水沟角钢gypsy 绞筒（锚机绞车上的）handrail 舷墙扶手hanging rudder; hinged rudder 吊舵；悬舵hatch; hatchway; hatch opening 舱口hatch bar 封舱压条hatch batten 舱口边压条hatch beam (web) 舱口大梁hatch booby 活动舱口盖hatch coaming 舱口板hatch cover 舱口盖hatch end beam 舱口端梁hatch moulding 舱口椽材hatch side girder 舱口纵桁hatch tarpaulin 盖舱布hatch trunk 舱口围阱hawse pipe 锚链管hawser 绳索；大缆heel 踵材；横倾hinged cover(door) 铰链盖（门）hold 货舱hold beam 舱内梁hold frame 舱内肋骨hold ladder 舱内梯hold stanchion(pillar) 舱内支柱hold stringer 舱内纵桁hopper 漏斗；开舱泥驳hopper tank 底边舱hopper tank sloping plating 底边舱斜板horizontal margin plate 水平内底板horizontal girder 水平桁horizontal stiffener 水平扶强材（防挠材）hull 船壳，船体hull construction 船体结构hull plating 船壳板hull strength 船体强度inner bottom 内底inner bottom plating 内底板insert plate 嵌板；衬板jack 千斤顶jack ladder 绳梯Jacob's ladder 软梯；绳梯Joggled joint 折接；弯合joggling machine 折曲机keel 龙骨keelblock 龙骨墩keel line 龙骨线；艏艉线keel plate 龙骨板keel rail （救生艇）艇底把手keelson 内龙骨kingpost 起重柱；将军柱knee 肘板；弯头knee of the deck 甲板梁肘板lightening hole 减轻孔lignum vitae 铁梨木local strength 局部强度local stress 局部应力longitudinal 纵骨；纵材；纵桁longitudinal bulkhead 纵舱壁longitudinal bending 纵向弯曲longitudinal framing system 纵骨架式longitudinal strength 纵向强度lug 耳板main deck 主甲板main frame 主肋骨manhole 人孔man hole door 人孔盖man hole coaming 人孔围板moment of inertia 惯性矩margin plate 内底边板molded breadth 型宽molded depth 型深mooring hole 导缆孔mooring post 系缆柱；岸柱mud box 泥箱non-return valve 止回阀non-watertight bulkhead 非水密舱壁notch 切口；槽口；刻痕oscillating load 振动负荷parallel middle body 平行中体panel stiffener 板格扶强材panting arrangement 防挠振结构panting beam 防挠振梁panting stringer 防挠振纵桁pillar 支柱；墩pintle 舵销plane bulkhead 平面舱壁plane keel 平板龙骨pump room 泵舱helm(rudder) pintle 舵销horizontal margin plate 水平内底边板out bottom plating 外底板platform 平台plating 壳板plimsoll mark 载重线标志poop 艉楼；船尾poop deck 艉楼甲板port 舷门；舱门；（装货）口；窗；门；孔porthole 舷窗；（装货）舷门propeller; propellor 推进器；螺旋桨propeller aperture 螺旋桨空间propeller boss(bub) 螺旋桨毂propeller shaft 艉轴racking （船体）横向挠度rail 扶手；栏杆rolling 横摇round of beam 梁拱round stern 圆（船）尾rudder 舵rudder carrier 舵托rudder casing 舵杆管rudder pintle 舵针；舵栓rudder plate; rudder blade 舵叶；舵板rudder post 舵柱rudder stock 舵杆rudder trunk 舵杆围壁；舵杆管rung （梯子）踏步；横档scallop 扇形开孔scantling 构件尺寸scantling of the structure 结构尺寸scarf; scarph 嵌接处；斜面；斜接scarf joint 斜（嵌）接scarf weld （斜面）焊接scarfing bracket 嵌接肘板scupper 排水孔scupper pipe 排水管scuttle 舷窗；人孔（盖）；小舱口盖seam 焊缝；接缝section 剖面section modulus 剖面模数semi-balanced rudder 半平衡舵shaft 轴shaft bracket 轴架shaft tube; stern tube 艉轴管shaft tunnel(alley; passage; trunk) 轴隧；地轴弄shedder plate 泄板；斜板sheer 舷弧；偏航sheer strake 舷顶列板shell 船壳；壳shell frame 舷侧肋骨shell plating 船壳板；外板shell strake; outside plating 船体外板shelter deck 遮蔽甲板shifting beam 活动舱口梁shifting board (or plank) 止移板（散装谷类）；防动板side girder 旁桁材side longitudinal 舷侧纵骨side plating 舷侧外板side strake 舷侧列板single bottom 单层底skid 护舷木；垫板skylight 天窗slanting plate 斜板slop tank 污油水舱sloping plate 斜板sloping plate longitudinal 斜板纵骨slot 槽；开缝sluice 水密门；水闸sluice valve 闸阀sniped end 削斜端soft toe 软趾solid floor 实肋板sounding pipe 测量管；测深管stabilizer 减摇装置stabilizing tank 减摇水舱staging 构架；台架；脚手架stanchion 支柱；栏杆柱static load 静载荷stay 支柱；撑条；支索stay bar(or rod) 撑杆stay plate 撑板stem 艏；艏柱；艏材stem post 艏柱stern 船尾，艉部stern counter 船尾突出体stern shaft; propeller shaft 艉轴stern poop 艉楼stern post 尾柱stiffener 防挠材；扶强材；加固物stool 托架，座，凳strake 列板strength calculation 强度计算strength deck 强力甲板stringer 纵桁stringer plate 甲板边板structural member 构件structural strength 结构强度strum box （舱底水）过滤箱strut 撑材，支柱，轴架stuffing box 填料箱superstructure 上层建筑tail (end) shaft 艉轴tarpaulin 防水油布，帆布，舱盖布thrust bearing(block) 推力轴承thrust shaft collars 推力环tieplate 带板，牵板，连接板topside tank 顶边舱；上边柜topside tank sloping plating 顶边舱斜板torsion 扭转torsion strength 扭转强度transom stern 方形船尾transverse 横梁，横材transverse bulkhead 横舱壁transverse frame 横肋骨，横框transverse framing system 横骨架式transverse ring 横环transverse strength 横向强度tripping bracket 防倾肘板tween deck 中间甲板tween deck frame 甲板间肋骨twisting distortion 扭转变形twisting moment 扭转力矩tunnel 轴隧，隧道，风筒tunnel escape 轴隧应急出口tunnel shaft bearing 中间轴支撑轴承ullage pipe (port) 油位测定管（孔）ullage space 空挡空间upper deck 上甲板upper (reverse) frame 内底横骨upper (lower) shelf plate 上（下）支架板upper (lower) stool 上（下）托架ventilator 通风筒vertical ballast trunk 竖向压载通道vertical girder 竖桁warping chocks 滚轮导缆钳wash bulkhead 可荡舱壁，挡水舱壁watertight bulkhead 水密舱壁watertight deck 水密门weather deck 露天甲板web beam 强横梁，桁板横梁web frame 加强肋骨，框架肋骨，桁板肋骨web plate 腹板wedge 楔木，楔子winch 起货机winch-head 绞车卷筒windlass 起锚机wing tank 翼舱，翼柜wire clip 钢缆夹wire reel 卷缆车，钢丝滚筒三、船舶材料及工艺常用英语A.S hipbuilding material (造船材料)T-bar T型钢Z-bar Z型钢I-B ar 工字钢channel bar 槽钢angle steel 角钢equal angle steel 等边角钢unequal angle steel 不等边角钢offset bulb plate 球扁钢flat plate 钢板round steel 圆钢half round steel 半圆钢steel pipe 钢管alloy steel 合金钢special steel 特种钢tempering steel 回火钢材low carbon steel 低碳钢high tensile steel 高强度钢copper 紫铜brass 黄铜aluminum alloy 铝合金stainless steel 不锈钢mechanical property 机械性能tensile test 拉伸试验bend test 弯曲试验impact test 冲击试验torsion test 扭转试验torsion strength 抗扭强度torsional deflection 扭转；扭转变形tensile strength 拉伸强度yield strength 屈服强度yield point 屈服点yield stress 屈服应力elastic limit 弹性极限ultimate strength 极限强度ultimate tensile stress 极限拉伸应力elasticity 弹性ductility 延展性，可塑（锻）性flexibility 挠性，柔性，易弯性toughness 韧性brittleness 脆性friability 易碎性hardness 硬度rigidity 刚性，稳定性heat treatment 热处理quench 淬火normalising 正火annealing 退火hardening 硬化，淬火tempering 回火casting 铸件，铸造forging 锻件，锻造pickling 酸洗ship timber 船用木材lignumvitae 铁梨木three-plywood 三夹板asbestos 石棉asbestos cloth 石棉布asbestos board 石棉板asbestos sheet 石棉纸asbestos cord 石棉绳asbestos paint 石棉涂料fiberglass 玻璃丝plastics 塑料resin 树脂rubber 橡皮painting 油漆cladding 镀层，表面处理coating 涂层，敷料corrosion 腐蚀，侵蚀wastage 损耗，蚀耗wear and tear 蚀损，磨损fracture 裂纹fatigue fracture 疲劳裂纹hairline fracture 发式裂纹buckling 皱折deformation 变形deflection, deflexion 挠曲flexion 弯曲lamellar tearing 层间撕裂rust 铁锈scale 锈皮pitting 点蚀，锈斑indent 凹痕，凹陷groove 槽沟detachment 脱开，脱焊rupture 断裂，破裂cropping 割掉renewal 换新descale 除锈grind 磨平be veed out 刨除alignment 对准，校直snip 剪断，剪片taper 削斜，斜度B.Shipbuilding workmanship （造船工艺）Working drawing 施工图end elevation 后面图front elevation 正面图side elevation 侧面图plane 平面图lines plan 型线图plan of waterlines 水线图general arrangement plan 总布置图construction plan 结构图damage plan 损坏示意图shell expansion plan 外板展开图docking plan 进坞图framing plan 船体构架图inboard profile plan 纵剖面图midship section plan 舯剖面图loaded waterline plane 满载水线图half breadth plan 半宽水线图stowage plan 配载图laying off lofting 放样mold loft floor 放样台mold loft 放样间template 样板mold loft batten, template batten 木样条evolute 展开线allowance 余量assembly 装配subassembly 分段装配subdivision length 分段长度shipbuilding tolerance 造船公差building berth 船台building dock 干坞slip dock 湿坞marine slipway, railway dry dock 船排marine slipway cradle 船排支架building block, stocks 枕木launch 下水launching ways 下水滑道launching grade 下水坡度launching cradle 下水架end launching 纵向下水side way launching 横向下水hydraulic press 水压机flanging machine 折边机plate bending machine 弯板机angle cutter 角钢切断机planing machine 刨边机shearing machine 剪床guillotine shear 龙门剪床oxy-acetylene welding 氧-乙炔焊co2 gas welding 二氧化碳气体焊arc welding 电弧焊unionmelt welding 埋弧自动焊fusion welding 熔焊fillet welding 角焊flat seam 对接缝butt joint welding 对接焊intermittent welding 间断焊；断续焊staggered intermittent welding 交错断续焊缝lap weld 搭接焊slot weld 槽焊；长孔焊plug weld 塞焊；圆孔焊run of welding 焊道welding torch 焊炬welding rod 焊条flux 焊药filler metal; deposited metal 熔敷金属welding stress 焊接应力welding procedure 焊接方法welding throat 焊喉cutting torch 割炬acetylene generator 乙炔发生器slag 熔渣undercut （焊接）咬边；根切hydraulic test 水压试验pressure test 压力试验flooding test 灌水试验hose test 冲水试验oil tight test 油密试验purchase trial 交船试验四、船舶性能常用英语angle of vanishing stability 稳性消失角buoyancy 浮性buoyancy curve 浮力曲线capsizing lever, upsetting lever 倾覆力臂capsizing moment, upsetting moment 倾覆力矩center of buoyancy 浮心center of floatation 漂心center of gravity 重心curve of areas of waterplanes 水线面积曲线curve of section areas 横剖面面积曲线curve of volumes of displacement 排水量曲线dynamical stability（curve）动稳性（曲线）entrance angle 进水角floodable length 可浸长度force of buoyancy, buoyant force 浮力free surface 自由液面heaving 垂荡heeling angle 横倾角heeling moment 横倾力矩hogging 中拱hogging condition 中拱状态hogging moment(stress) 中拱力矩（应力）hydrostatic curves 静水力曲线initial metacenter 初稳心initial stability 初稳性insubmersibility 抗沉性longitudinal inclination; list; heel 纵倾longitudinal stability 纵稳性panting （波浪对船体的）冲击period of rolling 横摇周期pitching 纵摇pounding 波浪冲击maneuverability 操纵性margin line 限界线metacenter 稳心moment to change trim one centimeter 每厘米纵倾力矩permissible length 许可长度potential head 势头pressure head 压头restoring moment, righting moment 复原力矩restoring lever, righting lever 复原力臂rolling 横摇sagging 中垂sagging condition 中垂状态sagging moment(stress) 中垂力矩（应力）seaworthiness 适航性stability 稳性stability at large angles 大倾角稳性stability criterion numeral 稳性横准数static head 静压头（力）statical stability (curve) 静稳性（曲线）surging 纵荡swaying 横荡tons per centimeter of immersion 每厘米吃水吨数total head (pressure) 总压头（力）transverse inclination, trim 纵倾transverse (longitudinal) metacenter 横（纵）稳心transverse (longitudinal) stability 横（纵）稳性trim by the bow (stern) 首（尾）倾turning quality (circle) 回转性（圈）velocity head 速头weigh curve 重力曲线yawing 艏摇五、船体检验常用英语THE DESCRIPTION OF DAMAGEA.G eneral descriptions1.in good condition 情况良好2.in poor condition 情况欠佳3.in bad condition 情况不佳，情况不良4.in a neglected condition 缺乏保养5.not properly serviced 未经正常保养6.not properly cleaned 未经正常清洁7.not properly protected未经正常保护8.not properly insulated未经正常隔热（或电气绝缘）9.not properly adjusted 未经正常校正10.defective 有缺陷的（失效）11.damaged 损坏damaged beyond repair 损坏了无法修复12.failed (in failure) 失效13.cut of order (in trouble) 故障 out of action 停止工作（作用），不是指故障14.in disorder 零乱（船属具零乱了）15.not working 不能工作16.inoperative 不能工作（失效）unworkable, inoperable 指本身不能工作，在损坏状况判断中不能使用17.out of function 不能工作，失去作用，不起作用18.unserviceable (useless) 不能使用（指必须换新的损坏部件）19.could not be started(failed to start)不能启动20.empty 空的21.fitted incorrectly 安装不正确（指小型的装置设备）installed incorrectly 安装不正确（指较大的装置设备）22.dangerous accumulation ofinflammable vapors 可燃气体危险集积it was obvious that this state had existedfor a considerable time （损坏）状况是长期存在的23.sluggish in (action, answering)（动作、应答）迟钝B.Deficiencies1.no…fitted, no…provided 未装2.no…available 未备有3.missing 遗失4.incomplete 不齐全，不完整5.deficient 不足，缺少6.insufficient 不足7.neglected 遗漏8.omitted 遗漏，省去9.removed 移开，拆走10.washed overboard 冲走11.dropped 跌落12.fitted with wrong ….(size, material, devices…) 错用（尺寸，材料，仪器）C.Tightness, stains, loss of etc.1.Leaking 漏2.infiltrating (seeping) 渗漏3.weeping 泪滴4.sweating 汗滴5.not watertight 不水密6.loss of watertightness 失去水密性（比5好）7.loss of airtightness 失去气密性8.loss of oiltightness 失去油密性9.escaping of cool 逃冷10.loss of lub-oil pressure 滑油压力降低11.loss of water pressure 水压力降低12.oil polluted 油污染13.oil soaked 油浸14.water soaked 水浸15.water stained 水渍16.oil stained 油渍17.rust in patches 锈斑18.verdigris in patches 铜绿斑19.water marks 水渍D.C rack, score, break etc.1.scuffed 拉毛（仅从反光上可观察到）2.chafed 擦痕3.scored 拉痕（痕较chafed深）4.scratched 抓痕（硬拉过的痕）5.scraped 刮痕（长期运行刮的痕）6.grooved 槽痕（比pitting深）7.ridged 凸起雷治痕（环状的痕）8.cracked 裂痕hair crack 发痕surface crack 表面裂痕through crack 穿透裂痕 non-through crack 未穿透裂痕9.chapped 龟裂，折裂10.fractured 折裂11.broken off 破掉（破裂后跌落）broken 破裂，破碎12.holed 穿洞13.holed & flooded 破洞浸水14.opened 开口15.bent 弯曲16.canted 倾斜17.buckled 皱折18.warped 翘起，翘曲19.indented (dented) 凹痕，凹陷（指船壳板在两档肋位间的凹陷）20.set in 凹陷（指船壳板较大面积的凹陷）21.waved 波曲22.curled 卷曲（指绳索）23.rumpled 褶皱（指垫片）24.bulged 鼓起，凸出25.collapsed 倾陷，倾倒26.ruptured 毁损27.torn off 撕破torn 拉脱28.pierced 刺破29.peeled 剥皮（油漆剥落）30.burst 爆破（指高压管路）31.blown off (packing) 吹脱32.distorted 扭曲，歪扭33.engine break-down 因故障机器突然停车E.Corrosion, seizing, choking etc.1.corrosion 腐蚀2.wasted 耗油3.deteriorated 蚀薄4.thinned 变薄5.pitted 麻点6.eroded 侵蚀7.rusted 生锈8.rotten （木、橡胶）腐烂、腐坏9.decayed （电缆）腐烂、腐坏10. aerated（橡胶、电缆）腐烂、腐坏11. aged 老化12. seized 咬住13. seized by corrosion 锈死14. stuck （粘）咬住15. rust-jammed 锈轧16. fouled 拥塞17. clogged堵塞（常指管子的堵塞）18. blocked 阻塞19. gagged 塞口20. foul & dirty 闭塞21. blanked 封没22. plugged 闭塞23. choked 卡住，阻塞F.Wear, loose, clearance etc.1.Loose 松动2.starting （铆钉）松动3.slack 松动slack back 松出4.worn 磨损5.worn cut evenly 均匀磨损6.worn cut unevenly 不均匀磨损7.worn on one side 单边磨损8.worn out symmetrically 对称磨损9.distorted （轴线弯曲并扭转）扭曲10.sprung （铆钉）扭歪11.twisted （轴线未弯、纯扭转）扭转12.excess clearance 间隙过大13.excess backlash 齿隙过大14.excess vibration 振动过大15.excess noise level 噪音过大16.loose engagement 啮合太松17.loose connection 接头松动18.tooth 齿worn out 磨损 chopped off 崩缺fractured 折断19.knocking 敲击 knocking cylinder 敲缸 knocking valve gear 伐件敲缸 knocking bearing 轴承敲缸20.bearing metal 轴承合金detached 脱壳cracked 开裂wiped 铺铅belted 熔化oil groove blocked 油槽堵塞21.out off roundness 失圆22.out off alignment 拉线不直23.off-centering 偏心24.deflected 偏斜G.B urning, heating, etc.1.Sparking 火花2.arcking (arcing) 电弧mutator 整流器scored 拉痕burnt 烧坏worn 磨耗，磨损uneven 不平sparking 火花blackened 发黑 rough 粗糙mica undercut 弧坑4.brush set incorrectly 碳刷安装不正确5.scorched 烤焦6.coked 结焦7.charred 结碳8.overheated 过热9.broken down 击穿10. short-circuit 短路11. setting incorrect 整定值不正确12. tripped incorrect 脱扣不正常13. batteriescompletely discharged（电）完全发光 undercharged 未充满overcharged 充电过量dry water 水干A. Remove, crop etc.1.Removed 拆下2.removed & replaced 拆装3.removed, faired & replaced拆装拷平4.cropped & renewed 割换（管、板、栏杆）5.partly renewed 部分换新6.partly cropped & renewed 部分割换7.cut off 割除8.faired 拷平9.faired on 原地拷平10.faired in place 原地拷平11.straightened 拷直、校直12.dismantle 拆卸（某一零件）13.disassembled 拆散（解体）14.stripped 拆除（某一部件）15.unshipped 拆下16.disconnected 断开（线、管接头）17.opened 打开18.lifted 抬升、举起19.jacked 顶起（用千斤顶顶起）20.replaced (by, with) 换用21.patch 贴补B.Fit, scrape, grind etc.1.fitted & scraped 拂刮2.fitted & ground 拂磨3.scraped & ground 刮磨4.made to fit 拂合（装配好）5.run to fit 跑合（运动磨合）6.ground round 磨圆7.ground smooth 磨光8.ground & reamed 磨绞9.bored round 镗圆10.planed smooth 刨光11.polished 抛光12.machined 光车13.skimmed 光刀14.finish machined 精加工15.rough machine 粗加工C.Re-metal, adjust, check etc1.Remetalled 重浇白合金2.re-babbitted 重浇白合金（专指巴氏合金）3.pulled out 拉出4.drawn out 抽出5.taken out 取出6.adjusted 调整，校正adjusted for alignment 校正拉线adjusted true 校正拉线 adjusted for clearance 校正间隙adjusted for centering 校中adjusted for deflection 校偏7.checked 检查checked for roundness 检查圆度checked for insulation resistance 检查绝缘电阻checked for centering检查中心位置checked for alignment 检查拉线checked for clearance 检查间隙8.cleaned 清洁9.wire-scrubbed 钢丝刷（除锈）10.chipped & scraped 拷锈（油漆）11.measured & recorded 测量并记录12.logged (hourly) 记录（小时）D.weld, rivet, wind etc.1.repaired by welding 电焊修理2.welded 补焊、焊接3.closed up by welds （面积、深度、高度较大）焊补4.built up by welds 堆焊5.plug welded 塞焊6.spot welded 点焊7.butt welded 对接焊8 tackweld 点焊、平头焊、定位焊。
船舶常用英语(一)汇总
一、船舶类型常用英语ship, vessel 船，船舶boat, craft 艇sampan 舢板, 小船manpowered boat 人力船sailor; sailing boat 帆船motor sailor 机帆船power-driven ship 机动船paddle steamer, paddle wheel vessel 明轮船screw ship; propeller vessel 螺旋桨船airscrew ship; aerial propeller vessel 空气螺旋桨船hovercraft; aircushion craft 气垫船hydrofoil 水翼船hydrojet propelled boat, water jet boat 喷水船steamship; steamer 蒸汽机船motor ship 内燃机船diesel ship 柴油机船electrically-propelled ship 电力推进船steam turbine ship 汽轮机船gas turbine ship 燃气轮机船nuclear-power ship 核动力船deck ship 甲板船flush deck ship 平甲板船raised quarter-deck ship 尾升高甲板船well-deck ship 半舱船single side ship 单舷长大舱口船three-island ship 三岛式船double shell ship 双壳船riveted ship 铆接船welded ship 焊接船transversely framed ship 横骨架式船longitudinally framed ship 纵骨架式船combined framed ship 混合骨架式船sea-going vessel 海船ocean-going vessel 远洋船coaster 沿海船channel ship 海峡船inland waterway vessel 内河船civil ship; merchant ship 民用船；商船transport ship 运输船pleasure yacht 游艇passenger ship 客船coasting passenger and cargo ship沿海客货船passenger and auto-car carrier 旅客及汽车运输船tourist ship; passenger carrier 旅游船第 1 页共24 页cargo ship; freighter 货船cargo liner 定期货船tramp ship 不定期货船container ship 集装箱船full-container ship 全集装箱船semi-container ship 半集装箱船multi-purpose container ship 多用途集装箱船general cargo ship/vessel/carrier 杂货船bulk (cargo) carrier 散货船ore carrier 矿砂船grain carrier 运粮船coal carrier; coaler 运煤船lumber(timber) carrier 运木船cattle carrier 运牲畜船multi-purpose ship 多用途船liquid cargo ship 液体货货船chemical tank 化学品液货船liquid chemical tanker 液体化学品船liquefied gas carrier 液化气体船liquefied petroleum gas tanker (LPG) 液化石油气运输船liquefied natural gas tanker (LNG) 液化天然气运输船tanker; oil tanker 油轮super tanker 超级油轮VLCC (very large crude carrier) (吨位在20万至30 万吨之间的) 巨型油轮ULCC (ultra-large crude carrier) (吨位在30万至50万吨之间的) 超巨型油船refrigerated ship; cold storage ship 冷藏船roll-on/roll-off ship (RO/RO ship) 滚装船ferry 渡船passenger ferry 旅客渡船freight ferry 货物渡船fishing vessel(boat) 渔轮trawler 拖网渔轮barge carrier; lighter aboard ship(LASH)载驳船barge; lighter 驳船deck barge 甲板驳well-deck barge 半舱驳double shell barge 双壳驳single side barge 单舷长大舱口驳oil barge 油驳container barge 集装箱驳船RO/RO barge 滚装驳船liquefied gas barge 液化气体驳. 专业.专注.hopper barge 开底泥驳split hopper barge 对开泥驳pusher; pushboat 顶推船；推船working ship 工程船tug; tugboat; towboat 拖船harbor tug 港作拖船rescue tug 救助拖轮salvage ship 救捞船dredger 挖泥船trailing suction dredge 耙吸挖泥船cutter suction dredger 绞吸挖泥船bucket wheel dredger 斗轮挖泥船bucket dredger 链斗挖泥船reclamation craft 吹泥船grab dredger 抓斗挖泥船dipper dredger 铲斗挖泥船floating pitter; drive pitter 打桩船floating crane; derrick boat 起重船floating dock 浮船坞cable layer; cable ship 布缆船scientific surveying ship 科学考察船research ship 科学调查船oceanographic research vessel 海洋调查船surveying ship 测量船ice-breaker 破冰船pontoon 浮舟; 浮桥; 趸船, 浮码头high speed craft 高速船passenger catamaran 双体客船vehicle ferry catamaran 双体车辆渡船vehicle-passenger ferry catamaran 双体车客渡船pontoon catamaran 双体趸船二、船舶结构常用英语center line 中心线，中线athwartships 横对船体（与船首尾线直交）bevel 斜角；斜面base line 基线amidships 在船中部；在纵中线上designed waterline breadth 设计水线宽designed waterline length 设计水线长draft 吃水former/aft draft 首/尾吃水draft figures 吃水尺度intersection 交点；交叉；横断面knuckle 折角线length between perpendicular 垂线间长. 专业.专注.length overall 总长load waterline length 满载水线长register length (breadth; depth) 登记长度（宽度、深度）freeboard 干舷rise of floor (dead; rise) 舭高；船底loadline mark 载重水线标记fresh water load line (F.) 淡水载重线fresh water timber load line (L.F.) 淡水木材载重线tropical fresh water load line (TF) 热带淡水载重线tropical load line (T) 热带载重线summer load line(S) 夏季载重线summer freshwater load line(F) 夏季淡水载重线winter load line(W) 冬季载重线winter North Atlantic load line(WNA) 冬季北大西洋载重线even keel （首尾）等吃水，平载extreme breadth 最大宽度floatable length 可浸长度sheer at forward (after) perpendicular 首尾舷弧sheer line 舷弧线accommodation 居住舱室accommodation deck 起居舱室；旅客甲板accommodation ladder 舷梯accommodation ladder platform 舷梯平台accommodation ladder manrope 舷梯扶索after body 后（部船）体after peak bulkhead 艉尖舱舱壁after peak tank 艉尖舱air hole 空气孔air pipe 空气管appendage （船体水线下的）附体；附件auxiliary machinery 辅助机械；辅机balanced rudder 平衡舵ballast 压载（物）ballast line 压载水管系ballast pump 压载水泵ballast pumping system 压载水系统ballast tank(water) 压载舱（水）batten 板条；压条（封仓用）batten-ceiling （货舱内）护舱条，护板beam 横梁beam bracket 梁肘板bearding 交合线，榫（艏柱或艉柱上）. 专业.专注.bending moment 弯矩bilge 舭部；舱底；（船底）污水沟bilge bracket 舭肘板bilge keel(chock, piece) 舭龙骨bilge knee 舭肘板bilge line 舭水管系bilge main 舭水总管bilge pipe (suction) 舭吸水管bilge pump 舭水泵bilge strake(plate) 舭列板bilge well 污水井bitt 系缆桩bollard 系缆桩；系船柱；双系柱bolster 枕垫bonnet 烟囱帽；机罩boom 杆；吊杆；桁；叉架boom crutch(support; rest) 吊杆支架bossing 尾管突出部；轴包套bottom frame 船底横骨bottom longitudinal 船底纵骨bottom plate 船底板bow 船首，船头bow fender 艏护垫bow flare 艏部外飘bow thruster 首侧推器bracket 肘板；（三角）拖架breakwater 挡浪板bridge 桥；桥楼；驾驶台bulb angle 圆头角材bulbous bow 球形船首，球鼻首bulb stern 球形船尾bulkhead 舱壁bulkhead plating 舱壁板bulkhead stiffener 舱壁扶强材bulwark 舷墙bulwark plating 舷墙板bulwark stay 舷墙扶强材bunker tank 燃料舱bushing 衬套butt 端接；残片butt joint(seam) 平接缝butt riveting 对接铆butt welding 对接焊butterfly clip 蝴蝶夹bypass valve 旁通阀cable stopper 止链器. 专业.专注.camber 翘曲camber of beam 梁拱cant beam 斜梁cant bracket 斜角板cant frame 斜肋骨cantilever 悬臂梁capstan 绞盘；绞缆机cargo batten 货舱护板cargo block 吊货滑车cargo port 装货舷梯，舷门cat walk （油轮上的）天桥，步桥center girder 中底桁center strake 中央内底板chafing plate 防擦板chafing ring 防擦环chain lock(well) 锚链舱chain pipe 锚链管chain stopper 止链器chock 导缆器；垫木clamp plate 夹板，压板cleat 羊角；系绳铁栓；防滑条coaming 围板；舱口围板cofferdam 隔离舱collar plate 封板collision bulkhead 船首舱壁；防撞舱壁companion way(hatch) 升降口corrugated bulkhead 槽形舱壁corrugation 皱；槽形；波形cross deck structure 舱间甲板结构crossing strength member 交叉强力构件cruiser stern 巡洋舰型船尾curtain plate 幕板cut out 开口；切davit 吊艇架；吊艇柱deck 甲板deck beam 甲板横梁deckhouse 甲板室deck line 甲板线deck longitudinal 甲板纵骨deck stringer(plate) 甲板边板deep tank 深舱derrick 吊杆diaphragm 隔板double bottom 双层底doubling plate 双层焊合板drain hole 排水孔. 专业.专注.duct keel 箱形龙骨dunnage 垫舱（物料）；衬垫dunnage wood 垫木dynamic load 动载荷end bracket 端肘板escape trunk （船内）应急通道engine bed 机座engine casing 机舱围壁escape scuttle （船内）应急出口escape vent 脱险口expansion joint 伸缩接头expansion trunk(tank) （油船）膨胀深井extension bracket 延伸肘板face plate 面板fender 碰垫；护舷材fender bar 护舷条fair lead 导缆器flame screen 防焰罩flange 折边flanged bracket 折边肘板flat keel 平板龙骨floor 肋板folding door 折门forecastle deck 艏楼甲板fore peak tank （船的）首舱；前尖舱forward perpendicular 首垂线foundation 底座frame 肋骨frame number 肋骨跨数frame space 肋距freeing port 甲板排水孔；放水孔gangway (gang ladder or gang board) 舷梯gasket 垫圈，垫料（集）密封垫general service pipe (G.S pump) 通用泵，总用泵girder 桁材gooseneck(parity iron) 鹅颈头；吊杆弯头grating 格子板；滑铁板ground tackle 锚泊索具gunwale 舷缘；舷边gunwale angle 舷边角钢gunwale bar 舷边角材gunwale railing 舷边栏杆gunwale tank 舷侧水柜（甲板下）gusset 角板；扣板gutter （甲板）水沟；槽沟. 专业.专注.gutter angle; waterway angle （舷侧）排水沟角钢gypsy 绞筒（锚机绞车上的）handrail 舷墙扶手hanging rudder; hinged rudder 吊舵；悬舵hatch; hatchway; hatch opening 舱口hatch bar 封舱压条hatch batten 舱口边压条hatch beam (web) 舱口大梁hatch booby 活动舱口盖hatch coaming 舱口板hatch cover 舱口盖hatch end beam 舱口端梁hatch moulding 舱口椽材hatch side girder 舱口纵桁hatch tarpaulin 盖舱布hatch trunk 舱口围阱hawse pipe 锚链管hawser 绳索；大缆heel 踵材；横倾hinged cover(door) 铰链盖（门）hold 货舱hold beam 舱内梁hold frame 舱内肋骨hold ladder 舱内梯hold stanchion(pillar) 舱内支柱hold stringer 舱内纵桁hopper 漏斗；开舱泥驳hopper tank 底边舱hopper tank sloping plating 底边舱斜板horizontal margin plate 水平内底板horizontal girder 水平桁horizontal stiffener 水平扶强材（防挠材）hull 船壳，船体hull construction 船体结构hull plating 船壳板hull strength 船体强度inner bottom 内底inner bottom plating 内底板insert plate 嵌板；衬板jack 千斤顶jack ladder 绳梯Jacob's ladder 软梯；绳梯Joggled joint 折接；弯合joggling machine 折曲机keel 龙骨. 专业.专注.keelblock 龙骨墩keel line 龙骨线；艏艉线keel plate 龙骨板keel rail （救生艇）艇底把手keelson 内龙骨kingpost 起重柱；将军柱knee 肘板；弯头knee of the deck 甲板梁肘板lightening hole 减轻孔lignum vitae 铁梨木local strength 局部强度local stress 局部应力longitudinal 纵骨；纵材；纵桁longitudinal bulkhead 纵舱壁longitudinal bending 纵向弯曲longitudinal framing system 纵骨架式longitudinal strength 纵向强度lug 耳板main deck 主甲板main frame 主肋骨manhole 人孔man hole door 人孔盖man hole coaming 人孔围板moment of inertia 惯性矩margin plate 内底边板molded breadth 型宽molded depth 型深mooring hole 导缆孔mooring post 系缆柱；岸柱mud box 泥箱non-return valve 止回阀non-watertight bulkhead 非水密舱壁notch 切口；槽口；刻痕oscillating load 振动负荷parallel middle body 平行中体panel stiffener 板格扶强材panting arrangement 防挠振结构panting beam 防挠振梁panting stringer 防挠振纵桁pillar 支柱；墩pintle 舵销plane bulkhead 平面舱壁plane keel 平板龙骨pump room 泵舱helm(rudder) pintle 舵销horizontal margin plate 水平内底边板. 专业.专注.out bottom plating 外底板platform 平台plating 壳板plimsoll mark 载重线标志poop 艉楼；船尾poop deck 艉楼甲板port 舷门；舱门；（装货）口；窗；门；孔porthole 舷窗；（装货）舷门propeller; propellor 推进器；螺旋桨propeller aperture 螺旋桨空间propeller boss(bub) 螺旋桨毂propeller shaft 艉轴racking （船体）横向挠度rail 扶手；栏杆rolling 横摇round of beam 梁拱round stern 圆（船）尾rudder 舵rudder carrier 舵托rudder casing 舵杆管rudder pintle 舵针；舵栓rudder plate; rudder blade 舵叶；舵板rudder post 舵柱rudder stock 舵杆rudder trunk 舵杆围壁；舵杆管rung （梯子）踏步；横档scallop 扇形开孔scantling 构件尺寸scantling of the structure 结构尺寸scarf; scarph 嵌接处；斜面；斜接scarf joint 斜（嵌）接scarf weld （斜面）焊接scarfing bracket 嵌接肘板scupper 排水孔scupper pipe 排水管scuttle 舷窗；人孔（盖）；小舱口盖seam 焊缝；接缝section 剖面section modulus 剖面模数semi-balanced rudder 半平衡舵shaft 轴shaft bracket 轴架shaft tube; stern tube 艉轴管shaft tunnel(alley; passage; trunk) 轴隧；地轴弄shedder plate 泄板；斜板sheer 舷弧；偏航. 专业.专注.sheer strake 舷顶列板shell 船壳；壳shell frame 舷侧肋骨shell plating 船壳板；外板shell strake; outside plating 船体外板shelter deck 遮蔽甲板shifting beam 活动舱口梁shifting board (or plank) 止移板（散装谷类）；防动板side girder 旁桁材side longitudinal 舷侧纵骨side plating 舷侧外板side strake 舷侧列板single bottom 单层底skid 护舷木；垫板skylight 天窗slanting plate 斜板slop tank 污油水舱sloping plate 斜板sloping plate longitudinal 斜板纵骨slot 槽；开缝sluice 水密门；水闸sluice valve 闸阀sniped end 削斜端soft toe 软趾solid floor 实肋板sounding pipe 测量管；测深管stabilizer 减摇装置stabilizing tank 减摇水舱staging 构架；台架；脚手架stanchion 支柱；栏杆柱static load 静载荷stay 支柱；撑条；支索stay bar(or rod) 撑杆stay plate 撑板stem 艏；艏柱；艏材stem post 艏柱stern 船尾，艉部stern counter 船尾突出体stern shaft; propeller shaft 艉轴stern poop 艉楼stern post 尾柱stiffener 防挠材；扶强材；加固物stool 托架，座，凳strake 列板strength calculation 强度计算. 专业.专注.strength deck 强力甲板stringer 纵桁stringer plate 甲板边板structural member 构件structural strength 结构强度strum box （舱底水）过滤箱strut 撑材，支柱，轴架stuffing box 填料箱superstructure 上层建筑tail (end) shaft 艉轴tarpaulin 防水油布，帆布，舱盖布thrust bearing(block) 推力轴承thrust shaft collars 推力环tieplate 带板，牵板，连接板topside tank 顶边舱；上边柜topside tank sloping plating 顶边舱斜板torsion 扭转torsion strength 扭转强度transom stern 方形船尾transverse 横梁，横材transverse bulkhead 横舱壁transverse frame 横肋骨，横框transverse framing system 横骨架式transverse ring 横环transverse strength 横向强度tripping bracket 防倾肘板tween deck 中间甲板tween deck frame 甲板间肋骨twisting distortion 扭转变形twisting moment 扭转力矩tunnel 轴隧，隧道，风筒tunnel escape 轴隧应急出口tunnel shaft bearing 中间轴支撑轴承ullage pipe (port) 油位测定管（孔）ullage space 空挡空间upper deck 上甲板upper (reverse) frame 内底横骨upper (lower) shelf plate 上（下）支架板upper (lower) stool 上（下）托架ventilator 通风筒vertical ballast trunk 竖向压载通道vertical girder 竖桁warping chocks 滚轮导缆钳wash bulkhead 可荡舱壁，挡水舱壁watertight bulkhead 水密舱壁watertight deck 水密门. 专业.专注.weather deck 露天甲板web beam 强横梁，桁板横梁web frame 加强肋骨，框架肋骨，桁板肋骨web plate 腹板wedge 楔木，楔子winch 起货机winch-head 绞车卷筒windlass 起锚机wing tank 翼舱，翼柜wire clip 钢缆夹wire reel 卷缆车，钢丝滚筒三、船舶材料及工艺常用英语A.Shipbuilding material (造船材料) T-bar T型钢Z-bar Z型钢I-B ar 工字钢channel bar 槽钢angle steel 角钢equal angle steel 等边角钢unequal angle steel 不等边角钢offset bulb plate 球扁钢flat plate 钢板round steel 圆钢half round steel 半圆钢steel pipe 钢管alloy steel 合金钢special steel 特种钢tempering steel 回火钢材low carbon steel 低碳钢high tensile steel 高强度钢copper 紫铜brass 黄铜aluminum alloy 铝合金stainless steel 不锈钢mechanical property 机械性能tensile test 拉伸试验bend test 弯曲试验impact test 冲击试验torsion test 扭转试验torsion strength 抗扭强度torsional deflection 扭转；扭转变形tensile strength 拉伸强度yield strength 屈服强度yield point 屈服点yield stress 屈服应力. 专业.专注.elastic limit 弹性极限ultimate strength 极限强度ultimate tensile stress 极限拉伸应力elasticity 弹性ductility 延展性，可塑（锻）性flexibility 挠性，柔性，易弯性toughness 韧性brittleness 脆性friability 易碎性hardness 硬度rigidity 刚性，稳定性heat treatment 热处理quench 淬火normalising 正火annealing 退火hardening 硬化，淬火tempering 回火casting 铸件，铸造forging 锻件，锻造pickling 酸洗ship timber 船用木材lignumvitae 铁梨木three-plywood 三夹板asbestos 石棉asbestos cloth 石棉布asbestos board 石棉板asbestos sheet 石棉纸asbestos cord 石棉绳asbestos paint 石棉涂料fiberglass 玻璃丝plastics 塑料resin 树脂rubber 橡皮painting 油漆cladding 镀层，表面处理coating 涂层，敷料corrosion 腐蚀，侵蚀wastage 损耗，蚀耗wear and tear 蚀损，磨损fracture 裂纹fatigue fracture 疲劳裂纹hairline fracture 发式裂纹buckling 皱折deformation 变形deflection, deflexion 挠曲flexion 弯曲. 专业.专注.lamellar tearing 层间撕裂rust 铁锈scale 锈皮pitting 点蚀，锈斑indent 凹痕，凹陷groove 槽沟detachment 脱开，脱焊rupture 断裂，破裂cropping 割掉renewal 换新descale 除锈grind 磨平be veed out 刨除alignment 对准，校直snip 剪断，剪片taper 削斜，斜度B.Shipbuilding workmanship （造船工艺）Working drawing 施工图end elevation 后面图front elevation 正面图side elevation 侧面图plane 平面图lines plan 型线图plan of waterlines 水线图general arrangement plan 总布置图construction plan 结构图damage plan 损坏示意图shell expansion plan 外板展开图docking plan 进坞图framing plan 船体构架图inboard profile plan 纵剖面图midship section plan 舯剖面图loaded waterline plane 满载水线图half breadth plan 半宽水线图stowage plan 配载图laying off lofting 放样mold loft floor 放样台mold loft 放样间template 样板mold loft batten, template batten 木样条evolute 展开线allowance 余量assembly 装配subassembly 分段装配subdivision length 分段长度shipbuilding tolerance 造船公差. 专业.专注.building berth 船台building dock 干坞slip dock 湿坞marine slipway, railway dry dock 船排marine slipway cradle 船排支架building block, stocks 枕木launch 下水launching ways 下水滑道launching grade 下水坡度launching cradle 下水架end launching 纵向下水side way launching 横向下水hydraulic press 水压机flanging machine 折边机plate bending machine 弯板机angle cutter 角钢切断机planing machine 刨边机shearing machine 剪床guillotine shear 龙门剪床oxy-acetylene welding 氧-乙炔焊co2 gas welding 二氧化碳气体焊arc welding 电弧焊unionmelt welding 埋弧自动焊fusion welding 熔焊fillet welding 角焊flat seam 对接缝butt joint welding 对接焊intermittent welding 间断焊；断续焊staggered intermittent welding 交错断续焊缝lap weld 搭接焊slot weld 槽焊；长孔焊plug weld 塞焊；圆孔焊run of welding 焊道welding torch 焊炬welding rod 焊条flux 焊药filler metal; deposited metal 熔敷金属welding stress 焊接应力welding procedure 焊接方法welding throat 焊喉cutting torch 割炬acetylene generator 乙炔发生器slag 熔渣undercut （焊接）咬边；根切hydraulic test 水压试验. 专业.专注.pressure test 压力试验flooding test 灌水试验hose test 冲水试验oil tight test 油密试验purchase trial 交船试验四、船舶性能常用英语angle of vanishing stability 稳性消失角buoyancy 浮性buoyancy curve 浮力曲线capsizing lever, upsetting lever 倾覆力臂capsizing moment, upsetting moment 倾覆力矩center of buoyancy 浮心center of floatation 漂心center of gravity 重心curve of areas of waterplanes 水线面积曲线curve of section areas 横剖面面积曲线curve of volumes of displacement 排水量曲线dynamical stability（curve）动稳性（曲线）entrance angle 进水角floodable length 可浸长度force of buoyancy, buoyant force 浮力free surface 自由液面heaving 垂荡heeling angle 横倾角heeling moment 横倾力矩hogging 中拱hogging condition 中拱状态hogging moment(stress) 中拱力矩（应力）hydrostatic curves 静水力曲线initial metacenter 初稳心initial stability 初稳性insubmersibility 抗沉性longitudinal inclination; list; heel 纵倾longitudinal stability 纵稳性panting （波浪对船体的）冲击period of rolling 横摇周期pitching 纵摇pounding 波浪冲击maneuverability 操纵性margin line 限界线metacenter 稳心moment to change trim one centimeter 每厘米纵倾力矩permissible length 许可长度. 专业.专注.potential head 势头pressure head 压头restoring moment, righting moment 复原力矩restoring lever, righting lever 复原力臂rolling 横摇sagging 中垂sagging condition 中垂状态sagging moment(stress) 中垂力矩（应力）seaworthiness 适航性stability 稳性stability at large angles 大倾角稳性stability criterion numeral 稳性横准数static head 静压头（力）statical stability (curve) 静稳性（曲线）surging 纵荡swaying 横荡tons per centimeter of immersion 每厘米吃水吨数total head (pressure) 总压头（力）transverse inclination, trim 纵倾transverse (longitudinal) metacenter 横（纵）稳心transverse (longitudinal) stability 横（纵）稳性trim by the bow (stern) 首（尾）倾turning quality (circle) 回转性（圈）velocity head 速头weigh curve 重力曲线yawing 艏摇五、船体检验常用英语THE DESCRIPTION OF DAMAGEA.General descriptions1.in good condition 情况良好2.in poor condition 情况欠佳3.in bad condition 情况不佳，情况不良4.in a neglected condition 缺乏保养5.not properly serviced 未经正常保养6.not properly cleaned 未经正常清洁7.not properly protected未经正常保护8.not properly insulated未经正常隔热（或电气绝缘）9.not properly adjusted 未经正常校正10.defective 有缺陷的（失效）11.damaged 损坏damaged beyond repair 损坏了无法修复. 专业.专注.12.failed (in failure) 失效13.cut of order (in trouble) 故障out of action 停止工作（作用），不是指故障14.in disorder 零乱（船属具零乱了）15.not working 不能工作16.inoperative 不能工作（失效）unworkable, inoperable 指本身不能工作，在损坏状况判断中不能使用17.out of function 不能工作，失去作用，不起作用18.unserviceable (useless) 不能使用（指必须换新的损坏部件）19.could not be started(failed to start)不能启动20.empty 空的21.fitted incorrectly 安装不正确（指小型的装置设备）installed incorrectly 安装不正确（指较大的装置设备）22.dangerous accumulation of inflammable vapors 可燃气体危险集积it was obvious that this state had existed for a considerable time （损坏）状况是长期存在的23.sluggish in (action, answering) （动作、应答）迟钝B.Deficiencies1.no…fitted, no…provided 未装2.no…available未备有3.missing 遗失4.incomplete 不齐全，不完整5.deficient 不足，缺少6.insufficient 不足7.neglected 遗漏8.omitted 遗漏，省去9.removed 移开，拆走10.washed overboard 冲走11.dropped 跌落12.fitted with wrong ….(size, material, devices…)错用（尺寸，材料，仪器）C.Tightness, stains, loss of etc.1.Leaking 漏2.infiltrating (seeping) 渗漏3.weeping 泪滴. 专业.专注.4.sweating 汗滴5.not watertight 不水密6.loss of watertightness 失去水密性（比5好）7.loss of airtightness 失去气密性8.loss of oiltightness 失去油密性9.escaping of cool 逃冷10.loss of lub-oil pressure 滑油压力降低11.loss of water pressure 水压力降低12.oil polluted 油污染13.oil soaked 油浸14.water soaked 水浸15.water stained 水渍16.oil stained 油渍17.rust in patches 锈斑18.verdigris in patches 铜绿斑19.water marks 水渍D.Crack, score, break etc.1.scuffed 拉毛（仅从反光上可观察到）2.chafed 擦痕3.scored 拉痕（痕较chafed深）4.scratched 抓痕（硬拉过的痕）5.scraped 刮痕（长期运行刮的痕）6.grooved 槽痕（比pitting深）7.ridged 凸起雷治痕（环状的痕）8.cracked 裂痕hair crack 发痕surface crack 表面裂痕through crack 穿透裂痕non-through crack 未穿透裂痕9.chapped 龟裂，折裂10.fractured 折裂11.broken off 破掉（破裂后跌落）broken 破裂，破碎12.holed 穿洞13.holed & flooded 破洞浸水14.opened 开口15.bent 弯曲16.canted 倾斜17.buckled 皱折18.warped 翘起，翘曲19.indented (dented) 凹痕，凹陷（指船壳板在两档肋位间的凹陷）20.set in 凹陷（指船壳板较大面积的凹陷）21.waved 波曲. 专业.专注.22.curled 卷曲（指绳索）23.rumpled 褶皱（指垫片）24.bulged 鼓起，凸出25.collapsed 倾陷，倾倒26.ruptured 毁损27.torn off 撕破torn 拉脱28.pierced 刺破29.peeled 剥皮（油漆剥落）30.burst 爆破（指高压管路）31.blown off (packing) 吹脱32.distorted 扭曲，歪扭33.engine break-down 因故障机器突然停车E.Corrosion, seizing, choking etc.1.corrosion 腐蚀2.wasted 耗油3.deteriorated 蚀薄4.thinned 变薄5.pitted 麻点6.eroded 侵蚀7.rusted 生锈8.rotten （木、橡胶）腐烂、腐坏9.decayed （电缆）腐烂、腐坏10. aerated（橡胶、电缆）腐烂、腐坏11. aged 老化12. seized 咬住13. seized by corrosion 锈死14. stuck （粘）咬住15. rust-jammed 锈轧16. fouled 拥塞17. clogged堵塞（常指管子的堵塞）18. blocked 阻塞19. gagged 塞口20. foul & dirty 闭塞21. blanked 封没22. plugged 闭塞23. choked 卡住，阻塞F.Wear, loose, clearance etc.1.Loose 松动2.starting （铆钉）松动3.slack 松动slack back 松出4.worn 磨损5.worn cut evenly 均匀磨损6.worn cut unevenly 不均匀磨损. 专业.专注.7.worn on one side 单边磨损8.worn out symmetrically 对称磨损9.distorted （轴线弯曲并扭转）扭曲10.sprung （铆钉）扭歪11.twisted （轴线未弯、纯扭转）扭转12.excess clearance 间隙过大13.excess backlash 齿隙过大14.excess vibration 振动过大15.excess noise level 噪音过大16.loose engagement 啮合太松17.loose connection 接头松动18.tooth 齿worn out 磨损chopped off 崩缺fractured 折断19.knocking 敲击knocking cylinder 敲缸knocking valve gear 伐件敲缸knocking bearing 轴承敲缸20.bearing metal 轴承合金detached 脱壳cracked 开裂wiped 铺铅belted 熔化oil groove blocked 油槽堵塞21.out off roundness 失圆22.out off alignment 拉线不直23.off-centering 偏心24.deflected 偏斜G.Burning, heating, etc.1.Sparking 火花2.arcking (arcing) 电弧mutator 整流器scored 拉痕burnt 烧坏worn 磨耗，磨损uneven 不平sparking 火花blackened 发黑rough 粗糙mica undercut 弧坑4.brush set incorrectly 碳刷安装不正确5.scorched 烤焦6.coked 结焦7.charred 结碳8.overheated 过热. 专业.专注.9.broken down 击穿10. short-circuit 短路11. setting incorrect 整定值不正确12. tripped incorrect 脱扣不正常13. batteriescompletely discharged（电）完全发光undercharged 未充满overcharged 充电过量dry water 水干A. Remove, crop etc.1.Removed 拆下2.removed & replaced 拆装3.removed, faired & replaced拆装拷平4.cropped & renewed 割换（管、板、栏杆）5.partly renewed 部分换新6.partly cropped & renewed 部分割换7.cut off 割除8.faired 拷平9.faired on 原地拷平10.faired in place 原地拷平11.straightened 拷直、校直12.dismantle 拆卸（某一零件）13.disassembled 拆散（解体）14.stripped 拆除（某一部件）15.unshipped 拆下16.disconnected 断开（线、管接头）17.opened 打开18.lifted 抬升、举起19.jacked 顶起（用千斤顶顶起）20.replaced (by, with) 换用21.patch 贴补B.Fit, scrape, grind etc.1.fitted & scraped 拂刮2.fitted & ground 拂磨3.scraped & ground 刮磨4.made to fit 拂合（装配好）5.run to fit 跑合（运动磨合）6.ground round 磨圆7.ground smooth 磨光8.ground & reamed 磨绞9.bored round 镗圆10.planed smooth 刨光11.polished 抛光12.machined 光车13.skimmed 光刀. 专业.专注.14.finish machined 精加工15.rough machine 粗加工C.Re-metal, adjust, check etc1.Remetalled 重浇白合金2.re-babbitted 重浇白合金（专指巴氏合金）3.pulled out 拉出4.drawn out 抽出5.taken out 取出6.adjusted 调整，校正adjusted for alignment 校正拉线adjusted true 校正拉线adjusted for clearance 校正间隙adjusted for centering 校中adjusted for deflection 校偏7.checked 检查checked for roundness 检查圆度checked for insulation resistance 检查绝缘电阻checked for centering检查中心位置checked for alignment 检查拉线checked for clearance 检查间隙8.cleaned 清洁9.wire-scrubbed 钢丝刷（除锈）10.chipped & scraped 拷锈（油漆）11.measured & recorded 测量并记录12.logged (hourly) 记录（小时）D.weld, rivet, wind etc.1.r epaired by welding 电焊修理2.w elded 补焊、焊接3.c losed up by welds （面积、深度、高度较大）焊补4.b uilt up by welds 堆焊5.p lug welded 塞焊6.s pot welded 点焊7.b utt welded 对接焊8 tackweld 点焊、平头焊、定位焊. 专业.专注.。