石油钻井英语
石油专业英语(钻井)课件
石油专业英语（钻井）2008-08-02 21:02Drilling 钻井Carry out drilling operation in accordance with the drilling program. 按钻井程序进行钻井作业. Prepared bell nipple. 准备”喇叭口”短节.Make up 2 joints of drill pipe. 接两根钻杆.Break out this connection. 卸开该接头.Run hole opener to sea bed. 下扩眼器到海底Mix gel fluid for drilling conductor hole. 为钻导管井眼配制高粘度泥浆.Make up bottom hole assembly. 组合下部钻具Check and reset crown-saver on every tour. 每个班都要检查并重新调整天车防碰装置.Number stands on trip out and trip in. 起下钻时给立柱编号.Pick up BHA and run to seafloor. 将下部钻具下到海底.Pick up stands. 接立柱（一个立柱就是三根钻杆接在一起）Don’t drill faster than 15 minutes for 1 stand. 钻进速度别超过15分钟1根立柱Drop TOTCO. 投(陶特)测斜仪Fish TOTCO with overshot. 用打捞筒捞起测斜仪Resume drilling to T.D. 继续钻进到总深Circulate 15 minutes.循环15分钟Run in hole. 下钻Put out of hole. 起钻Make an inventory of all ring gaskets. 开一个所有垫圈的清单Use spinning tong. 使用气动扳手Operate the air winch. 操作气动绞车Lay down 57 joints of 5”drill pipe. 甩57根钻杆Pick up drill stem test tool. 提起钻杆测试工具Circulate mud for 2 hours. 循环泥浆2小时Move string during circulation. 在循环时注意活动钻具Circulate hole clean. 循环清洗井眼Circulate bottoms up. 循环泥浆几周Fill up every 5 stands. 每5柱灌泥浆一次Check mud weight every 15 minutes.每15分钟检查泥浆比重Reverse out excess cement. 反循环替出多余的泥浆Change/replace old mud by new mud.用新的泥浆替换出旧的泥浆Stop drilling. 停止钻进Drilling ahead. 钻进Pull out of hole bit. 起出钻头Change bit. 换钻头Run the wear bushing. 下抗磨补心The bit thread type is regular pin. 钻头丝扣是正规公扣What’s the make-up torque? 上扣扭矩要多大?Run in 9”collars. 下9”钻铤The cathead can’t give enoughtorque. 猫头力量不够Connect crossover sub. 接上配合接头The tong angle is too small. 大钳的角度太小了地质年代术语英汉对照2008-08-0221:04stratum 地层stratigraphic correlation 地层对比horizon 层位key bed 标志层barren bed 哑层lacuna 缺失hiatus 间断continuity 连续discontinuity 不连续conformity 整合unconformity 不整合angular unconformity 角度不整合para-unconformity 平行不整合geochronologic unit 地质年代单位eon 宙era 代period 纪epoch 世stage 期chron 时chronostratigraphic unit 年代地层单位eonothem 宇erathem 界system 系series 统stage 阶chronozone 时带biostratigraphic unit 生物地层单位biostratigraphic zone 生物地层带lithostratigraphic unit 岩石地层单位group 群formation 组member 段bed 层geochronologic scale 地质年代表Phaneozoic Eon(Eonothem)显生宙（宇）Cainozoic Era(Erathem) 新生代（界）Cenozoic Era(Erathem) 新生代（界）Quaternary Period(System) 第四纪（系）Holocene Epoch(Series) 全新世（统）Pleistocene Epoch(Series) 更新世（统）Tertiary Period(System) 第三纪（系）Neogene Period(System) 新第三纪（系）Pliocene Epoch(Series) 上新世（统）Miocene Epoch(Series) 中新世（统）Paleogene Period(System) 老第三纪（系）Oligocene Epoch(Series) 渐新世（统）Eocene Epoch(Series) 始新世（统）Paleocene Epoch(Series) 古新世（统）Mesozoic Era(Erathem) 中生代（界）Cretaceous Period(System) 白垩纪（系）Jurassic Period(System) 侏罗纪（系）triassic Period(System) 三叠纪（系）Palaeozoic Era(Erathem) 古生代（界）Permian Period(System) 二叠纪（系）Carboniferous Period(System) 石炭纪（系）Devonian Period(System) 泥盆纪（系）Silurian Period(System) 志留纪（系）Ordovician Period(System) 奥陶纪（系）Cambrian Period(System) 寒武纪（系）Cryptozoic Eon(Eonothem) 隐生宙（宇）Proterozoic Eon(Eonothem) 元古宙（宇）Neoproterozoic Era(Erathem) 新元古代（界）Sinian Period(System 震旦纪（系）Mesoproterozoic Era(Erathem) 中元古代（界）Palaeoproterozoic Era(Erathem) 古元古代（界）Archaean Eon(Eonothem) 太古宙（宇）Precambrian 前寒武纪石油钻井词汇Part One SLICK-LINE（钢丝作业）A. TOOLS rope socket 绳帽stem 加重杆roll stem 滚轮加重杆Tungsten stem 钨加重杆Lead stem 铅加重杆link jar 机械震击器tubular jar 管状震击器hydraulic jar 液压震击器spring jar 弹簧震击器knuckle joint 万向节swivel joint 旋转节wellhead adapter 井口变扣短节X-Over 变扣gauge cutter 通井规selective downshift tool 选择性滑套开关工具shiftting tool 移位工具blind box 盲锤L.I.B(lead impression block) 铅印swaging tool 胀管器spear 打捞矛prong grab 内捞矛center spear 外捞矛catcher 捕捉器wirefinder 钢丝探测器Go devil-F.B 平底撞棍Go devil-C.B 刀杆撞棍retriever 钢丝打捞器overshot 卡瓦打捞筒magnetic fishing tool 磁力打捞工具sidewall cutter 刮管刀alligator grab 鳄鱼爪sand bailer 捞沙筒pipe wrench 管钳tong chain 链钳spanner 扳手wireline clamp 钢丝夹hay pulley 地滑轮dump bailer 倾倒筒saw 锯子saw blade 锯条punch 冲子file 锉刀flat file 板锉,扁锉hammer 榔头pliers,vice 老虎钳wire cutter 断线钳forfex 剪刀tongs 大钳,钳子,管钳flat bit tongs 扁嘴钳screwdriver 改锥，螺丝刀wire stripper 剥皮钳,掳线钳wire-stripper pliers 剥线钳B. EQUIPMENTstuffing box 防喷盒lubricator upper section 上防喷管lubricator middle section 中防喷管lubricator lower section 下防喷管blowout preventer(BOP) 防喷器wellhead adapter 井口变扣短节Lincoln pump 林肯泵hand pump assy.for stuffing box 手压泵Fire extinguisher 灭火器hand tool box 手工具箱injector 注油器lifting cap BOP吊帽trolly 防喷管支撑架parasol 阳伞work vice 台钳chain block 链葫芦tie down chain 系紧链fixed pulley 定滑轮wobble pump 手摇泵wire line clamp 钢丝绳夹wire rope sling 绳套,钢丝吊绳winch 绞车winch barrel(drum) 绞车滚筒winch brake 绞车刹车winch drive shaft universal joint 绞车主动轴万向节winch drum shaft 绞车滚动轴winch line 吊装用绳套winch control panel 绞车控制面板winch truck 吊车C. OPERATIONSRTTS Operation for Shoot andPull RTTS完井服务RTTS Operation for CementSqueezing RTTS固井服务（挤水泥）Pulling Y Block 捞Y堵塞器Open SSD(Slide Side Door) 开生产滑套Close SSD(Slide Side Door) 关生产滑套Open Circulating SSD(Slide SideDoor) 开循环滑套Close Circulating SSD(Slide SideDoor) 关循环滑套Running Gauge Cutter 通井Clean up 地面完井放喷Open Drain Valve 砸泻油阀Pulling Test Plug 捞测试阀Running Jet Pump 投射流泵Pulling Jet Pump 捞射流泵Running Flow Regulator 投配水器Pulling Flow Regulator 捞配水器Fishing Drop Bar 捞点火棒Measuring Static Pressure 测静压Measuring Flowing Pressure 测流压Measuring BHPBU(Bottom Hole Pressure Build Up) 测压力恢复Measuring BHP(Bottom Hole Pressure) Testing with Jet Pump 带泵测压（射流泵）Multi-Rate BHP(Bottom Hole Pressure) Testing 系统试井Slick-line Operation for Completion 钢丝配合完井服务Slick-line Operation for acidizing 配合酸化钢丝作业Running Plug 投堵塞器Pulling Plug 捞堵塞器Run Impression Block 下铅印Running Prong 投平衡杆Sand Level detection 探沙面Run Sand Bailer 下捞砂桶Open SSSV(Sub Surface Safety Valve) by Force 强行打开井下安全阀Running Go Devil 剪切钢丝Fishing Slickline 打捞钢丝Running Side Pocket Plug 投偏心堵塞器Pulling Side pocket Plug 捞偏心堵塞器Running Side Pocket Check Valve 投偏心阀Pulling Side Pocket Check Valve 捞偏心阀Sand Sampling 取砂样Stable Test 稳定试井Slickline Swab 抽吸Running Hanger 投悬挂器Pulling Hanger 捞悬挂器D. SPARE PARTSgrease injection control head 注脂头grease oil 注脂油grease oil tank 注脂油桶BOP pump c/w hose 手压泵及管线pressure test hose 试压管线lubricator bleed off manifold 防喷管针阀Martin Decker W-15 oil 马丁代克油Martin Decker WT indicator c/whose 指重器及管线picking for stuffing box 盘根bearing for the sheave for stuffingbox 轴承O-ring for lubricator 防喷管O环ram assembly for BOP 防喷管闸板总成O-ring for BOP BOP O环O-ring for wellhead adapter 井口变扣O环pin 销钉counter head 计数头cable for counter 计数器软轴bearing of hay pulley 地滑轮轴承Part two Pressure gaugeaccordance 一致,和谐accuracy 精确性,正确度acquisition 获得,获得物alignment 校直,调准append 附加,添加,悬挂apply 申请,应用available 可利用的,有用的battery 电池battery housing 电池筒battery tester 电池测量器baud rate 波特率bull nose 底堵cable 电缆,电线cable head 电缆头,电缆接头calculation 计算,考虑calibration 标度,刻度,校准calibration drift 漂移calibration parameter 标定参数cartesian 笛卡儿曲线certification 证书com port 串行通讯端口command 命令,掌握,支配communicate 沟通,交流,通讯compensate 偿还,补偿configuration 构造,结构,配置,外形configure 配置,设定consist 组成,构成control panel 控制面板convert 转换,使转变cross-over between gauge 压力计间变扣crystal 水晶,晶体current 电流damage 危险,损害data acquisition 获得数据decode 解码,译解delta time 累计时间deviate 偏离diagnostic 诊断diameter 直径digital 数字的directory 目录discussion 讨论display 显示器,显示,展示downhole tools 井下工具drain 消耗,耗尽dump data 回放数据durability 耐用性element 元素,元件,成分elevated temperature 高温encoder 译码器,编码器establish 建立,安置filter 过滤,筛选firmware 固件(软件硬件相结合)fixed rate 固定采样率flash 闪光,闪现frequency 频率,周率gauge 压力计graph 图表,曲线图grease for transducer 传感器用油housing 壳,壳体incorporate 合并,混合indicate 指出,显示individual 个别的,单独的install 安装,安置instrument 工具,器械,器具interface box 接口箱interface box 接口箱internal diagnostics 内部诊断lapse 失误,下降,过失linear plot 线性平面图log 日志maintenance 维护,保持manual 手册,指南manufacture 制造,加工merge 合并,并入,结合memory 存储器,内存module 模块observe 观察,观测offer 提供,企图parallel communication 并行通信period 周期,时期plug 堵,塞,插上,插栓port 端口,港口potential 潜在的,可能的presentation 陈述,表达presentation software 操作软件printer 打印机prior 优先的,在前的procedure 步骤,手续program 程序,节目prune 剪除,修剪,删除quality 质量,品质,性质quartz 石英range 范围,射程real time 实际时间record mode 记录模式reduce 减小,缩小,简化remote control 遥控,遥控操作remove 移动,开除,移交require 请求,要求resolution 分辨率response 回答,响应scale 刻度,天平,比例尺select 选择,挑选setup 机构,安装,装备,组织silicone oil 硅油sleep mode 休眠模式spanner for gauge 压力计专用扳手SRO(surface read-out) 地面直读surpass 超过,胜过talk mode 对话模式terminal 终点终端thread grease 丝扣油transducer 传感器,变频器,交换器transient 短暂的,瞬时的transmit 传输,传送,发射信号transport 传送器,运输机transportation box 压力计箱troubleshooting 发现并修理故障truncate 截取,修剪update 更新,校正,修正upload 上载variable rate 可变采样率various 不同的,多样的version 版本,译本volt 伏特voltage 电压wand 棒,棍,杖zoom 放大,缩放Part three PVT取样 air chamber plug extractor 空气室拉出手柄air chamber plug retaining ringextractor 梭管套旋出手柄air chamber tube assy 导流管air hose assy. 扫空管allen key 内六角autoclave vacuum nipple 抽真空头B/bench hose assy. 样瓶转样管back-up ring 背环compression spring 压缩弹簧filler funnel 漏斗flow regulator body 节流器flow regulator end cap 端帽flow regulator extractor 节流器拉出手柄fuse/110V 保险丝/110Vglycol 甘醇heating jacket for cylinder 样瓶加温器heating jacket for sampler 取样器加温器holder 装配手柄internal circlip 内簧卡internal circlip for cylinder 取样瓶卡环lock grubscrew 锁紧螺丝needle valve 针阀needle valve assy.extractor 针阀手柄needle valve body 针阀组件needle valve BUR former 针阀背环工具off ball 钢球off diskspring 弹簧片piston assy. 活塞总成piston removal 活塞移位工具piston ring 活塞环piston rod 活塞杆piston valve stem 梭阀杆pols-lock pin 锁定销钉pols-lock spring 锁定销钉弹簧posi lock pin depressing tool 锁定按压工具prime hand pump 注油器prime hand pump adaptor 注油器适配器prime port adaptor assy. 加压口适配器prime port nipple plug 加压口堵头prime port spanner 加压阀扳手prime pump assy. 手压泵适配器prime pump hose assy. 手压泵输出管push rod 推杆relief valve stem 调压阀杆retaining ring 制动环reversible circlip pliers 卡簧手钳safety solvent 清洗液sample analysis 试样分析,样品分析sample analyzer 试样分析器sample bailer 采样筒sample blob 井底取样器sample bomb 高压取样瓶,样品存储器sample bottle 取样瓶,采样瓶sample bottle valve adaptor 样瓶接头sample chamber 样品室sample cock 取样旋塞,取样拷克sample collection 取样,样品收集sample collection procedure 取样点,采样点sample collector 取样程序sample connection 试样收集器,采样员sample container 取样接头sample contamination 样瓶,样筒,样品容器sample cup 样品污染sample cylinder 样品杯sample cylinder tag 样瓶,样筒sample date 样瓶标签sample depth 取样日期sample frequency 采样深度sample hose 采样信号sample identification 取样井,采样井sample integrity 采样频率sample interval 样品管,采样胶皮管sample period 样品鉴定sample point 样品的真实性sample signal 取样间隔,取样速度sample well 取样周期sampler hose assy. 取样器软管总成setting screw 制动螺丝setting fork 导流叉管setting tool 空气定位销手柄setting tool 梭杆推进套shuttle mechanism assy. 触发机构tee ring seals T型密封环test gauge 压力表tool body clamp 取样器夹具tool dressing aids 更换'O'环工具torque wrench 扭矩扳手torque wrench adaptor 扭矩扳手接头torque wrench adaptor 扭矩扳手接头transfer bench assy. 转样器总成transfer lock sleeve 转样护帽transfer port adaptor 转样适配器transfer port plug 转样口堵头trigger mech. assy. 触发机构总成trigger spring 触发弹簧vacuum hand pump 真空泵vibra gauge 压力表Part four OthersAa directional engineer 定向井工程师a drilling engineer 钻井工程师a drilling supervisor 钻井监督a senior mud engineer 高级泥浆工程师a toolpusher 队长，技师abandoned drill 弃船演习accelevator 促凝剂acidity 酸性adapter 接头additive 添加剂/处理剂ahead water 先行水air chamber 空气包air hoist 气动绞车alarm 警报alkalinity 碱性泥浆比重amplitude log 声幅测井anchor 锚angle 角钢annular return velocity 泥浆返回流速annular space 环形空间annular velocity 环空流速apparent viscosity 视黏度asbestos 石棉assistant tug boat 护航船assistant driller 副钻aviation fuel 航空油Bback off 倒扣back pressure 回压back pressure valve 回压阀ball 球ball up 泥包barge engineer 平台工程师barite 重晶石bearing 轴承bearing angle 方位bed 床behind water 尾水bit 钻头bit bearing 钻头轴承bit breaker 钻头装卸器bit cost 钻头成本bit diameter 钻头直径bit gauge 钻头规bit life 钻头寿命bit nozzle 钻头水眼bit position 钻头位置bit sub 钻头接头bit time 钻头纯钻时间bit tooth 钻头牙齿bit torque 钻头扭矩bit type 钻头型号bit wear 钻头磨损blasting cap 雷管blow out 井喷blow out preventer 防喷器boiler 锅炉bolt 螺栓bolt,nut 螺丝,螺母bore hole 裸眼bore hole well 井壁boring 钻孔bottom hole 井底bottom fill 沉砂bottom hole pressure 井底压力bottom hole pressure 井底压力bottoms up 携带岩屑box 母扣brake 刹车break out 卸扣breech lock 泡栓build up 压力恢复bulk density 堆积密度;松装密度bulk tank 灰罐bumper sub 缓冲器buoyancy coefficient 浮力系数bushing 补芯butane 丁烷Ccable 电缆calcium remover 除钙剂calculating free piont 计算卡点深度calibration 刻度casing 套管,螺纹联接的兀接箍casing head 套管头casing spool 套管四通casing burst pressure 套管破裂压力casing elevator 套管吊卡casing monkey board 套管平台casing pressure 套压casing program 套管程序casing scraper 套管刮管器casing shoe 套管鞋casing sub 套管接头casing tong 套管大钳cathead 猫头cave in 坍塌cement 水泥cement basket 水泥伞cement bond log 固井质量检验cement flush 水泥冲洗cement slurry 水泥浆cement slurry for lead 先行水泥浆cementing 固井cementing line 固井管线cementing pump 固井泵center latch elevator 中开门吊卡centralizer 套管扶正器centrifugal pump 离心泵chain block 倒链change bit 换钻头chart 卡片check valve 单流阀chemical tank 化学药剂缸chemical treatment 化学处理chemicals 化学剂choke 油嘴choke line 阻流管汇choke manifold 试油树christmas tree 采油树circulating pressure 循环压力circulation 循环circulation rate 循环速度clamp 卡子clay contamination 粘土侵clock 时钟clog house 值班房cock 水龙头coefficient of friction 摩擦系数colloid 胶体completion 完井computer 计算机conductor 隔水导管cone 牙轮cone bit 牙轮钻头connector 联结器contamination of mud 泥浆污染contract 合同contractor 承包商control room 控制室conventional mud 普通泥浆cooker 炊事员core 岩心core barrel 取芯筒core bit 取芯钻头core catcher 岩心爪core gun 取芯器core handling tools 取芯工具core recovery 取芯收获率coring 取芯coupling 联接扣cover 外壳crane operator 吊车司机critical velocity 临界速度cross 十字接头cross over,x-over(XO) 大小头，短节，变扣接头，旁通管crossover sub 配合接头crown block 天车cut off workline 割大绳cylinder 缸Ddaily production 日产量deadline 死绳deadline anchor 死绳固定器deck 甲板declination 偏差/方位角degas ser 除气器dehydration 失水densimeter 密度计depth 井深derrick 井架derrick man 架工desander 除砂器desilter 沉淀池, 滤水池detonator 炸药deviation survey 井斜测量diamond bit 金刚石钻头die collar 打捞卡瓦diesel oil 柴油different pressure sticking 压差卡钻directional well 定向井discharge of pump 泵排量dispersing agent 分散剂displace 替diver 潜水员doctor 医生drag 遇阻draw works 绞车drier(dring oven) 干燥计drift angle 倾角drift mandrel 通径规drifting 通径drill pipe 钻杆drill spool 钻井四通drill stem 钻柱drill strings 钻杆拄drill water 钻井水drill collar 钻铤drill floor 钻台drill floor 钻台driller 司钻drilling 钻进drilling technician 钻井技术员drilling assembly 钻具组合drilling break 进尺突然加快drilling cost 钻井成本drilling crew 钻井队员drilling engineer 钻井工程师drilling equipment 钻井装置,钻机drilling line 大绳drilling log 钻井记录drilling ration 钻速drilling recorder 钻井记录仪drilling rig 钻井船drilling troubles 井下事故drum shaft 滚筒轴DST(drill stem test) 延长DST测试dump valve 放泄阀duplex slush pump 双缸泥浆泵DV collar 分级注水泥短接DV port DV孔Eelbow 弯接头electric logging 电测electric submerged pump(ESP) 电潜泵electrician 电工elevator 吊卡elevator link 吊环emulsifier 乳化剂engine room 机舱erecting equipment 安装设备erecting tools 安装工具erode out 刺坏error 误差ethane 乙烷exploration 勘探extended well testing 延长测试external upset 外加厚Ffalse threading 造扣field maintenance 现场维护，现场保养fill line 灌泥浆管线filling up mud 灌泥浆filter cake 泥饼filter paper 滤纸filtration educing agent 降失水剂finger board 指梁fire drill 消防演习fishing 打捞fishing bumper sub 打捞缓冲器fishing jars 打捞震击器fishing job 打捞作业fishing neck 打捞颈fishing tools 打捞工具fishing up 打捞出落鱼flash welded tool joint 闪光焊接接头flashlight 手电float collar 浮箍float shoe 浮鞋floor man 钻工flow 放喷flow line 泥浆出口管线flow rate 流量flow line 出油管flow rate 流速flowing bean(nipple) 油嘴flowing pressure gradient 流压梯度fluid loss 失水量fluorescence 荧光反应formation 地层formation conductivities 地层电导率formation damage 破坏地层fracturing 压裂free pipe 未卡部分钻柱free point 自由点free standing mast 无绷绳轻便井架fresh water 淡水full hole(FH) 贯眼扣function 函数funnel viscometer 漏斗黏度计Ggamma ray 射线gamma ray log 自然测井gas reservoir 气层gas analysis 气体分析gas chromatography 气体色谱仪gas cut 气侵gas in mud 泥浆中气量gas oil ratio 油气比gas out 气侵gas showing 气体显示gasoline 汽油gauge 量规gear 牙轮gel 凝胶gel cement 胶质水泥gel mud 胶质泥浆gel strength 切力generator 发动机geothermal gradient 地温梯度goose neck 鹅颈管grade 级/等级grease 黄油guide shoe 引鞋gun perforation 射孔完井gypsum mud 石膏泥浆Hhammer 锤子hard ware 硬件heavy mud 重泥浆/加重泥浆heavy viscosity mud 高粘泥浆heavy weight drill pipe 加重钻杆heavy bodied 很稠的，粘滞的helicopter 直升飞机helicopter port 飞机平台helmet 安全帽hole opener 扩眼器hole size 井眼尺寸hole straightening 井眼校正/纠斜hook 大钩hook load 大钩负荷hook load off bottom 钻柱离底时大钩负荷hook position 大钩位置hopper 漏斗hose 软管/水龙带hull 船身hydraulic pressure 静水压力hydraulic oil 液压油hydrostatic pressure 静水压力IIF(internal flush) 内平扣indented bolt 齿纹螺栓indented chisel 齿状钻头，牙轮钻头indirect flushing 反循环洗井，反向冲洗induction electrical survey 感应电测井inertia brake 惯性刹车initial gel strength 出切inner barrel 内岩心筒inner string cementing 内管注水泥input 输入insert bit 镶齿钻头inside bop drill 安装回压凡尔演习intake profile 吸水剖面internal upset 内加厚internal-external upset 内外加厚interpreter 翻译invaded zone 侵入带invasion diameter 侵入直径inverse circulation 反洗井inverse well-flushing 反洗井isobutane 异丁烷isopentane 异戊烷Jjack knife mast 折叠式轻便井架jack up type drilling unit 自升式钻井船jars 震击器joint 单根junk basket 打捞蓝Kkelly 方钻杆kelly bushing 方钻杆补芯kelly cock 方钻杆考可kelly down 方入kelly down depth 方入深度kelly drive 方钻杆滚子补芯kelly spinner 方钻杆旋扣器kelly up 方余key seat 键槽key seating sticking 键槽卡钻kick 井涌kick control 控制井涌kill line 压井管汇killing a well 压井Llaminar flow 层流latching elevator 扣吊卡lay down 甩lay time 迟到时间leak 漏life raft 救生筏lifeboat 救生艇lift jacket 救生衣lifting sub 提升短接light weight mud 轻泥浆lignite 铁络盐lignite mud 铁络盐泥浆lime 石灰lime mud 石灰泥浆limit switch 相限开关line 管线line cleaning 管线清洗line test 管线试压liner 缸套,尾管liner hanger 尾管挂living quarters 居住区loading 装船logging cable 测井电缆logging program 测井程序logging tool 测井工具loosen 放松lost circulation 井漏lost circulation materials 堵漏剂lubricating oil 润滑油lubricator(assembly,system) 防喷管（装置，系统）Mmachine oil 机油main tug boat 主拖轮make up 上扣make up torque 上扣扭矩mast 钻机master bushing 转盘大补芯master valve 总闸门material man 材料员mean sea level 平均海平面mechanic 机械工mechanist 机械师methane 甲烷mica 云母milled teeth bit 铣齿钻头milling tool 铣具/磨鞋miring water 溶解水mixing pump 混合泵monkey board 二层台morning tour 白班motormen 机工mouse hole 鼠洞mud 泥浆mud agitator 泥浆搅拌器mud balance 泥浆密度计mud column 泥浆柱mud conditioning 泥浆处理/配泥浆mud conductivity 泥浆导电率mud density 泥浆密度mud ditch 泥浆槽mud flow meter 泥浆流量计mud gun 泥浆枪mud line 泥浆管线mud logging 泥浆录井mud pump 泥浆泵mud resistivity 泥浆电阻率mud retort 泥浆蒸馏水mud return line 泥浆返出管线mud tank 泥浆池mud temperature 泥浆温度mud testing 泥浆测试mud volume 泥浆量mud weight indicator 泥浆比重计mud tank 泥浆罐multiple completion 多层完井MW(mud weight) 泥浆重量,泥浆密度Nnail 钉子natural flow 自喷NDBOPS(nipple down blowout preventers) 卸下防喷器组NDT(nipple down tree) 拆卸井口装置，拆卸采油树near bit stabilizer 金钻头扶正器neutron 中子射线nipple down 卸下，拆卸nipple seating 座落接头no return 未返回水泥浆normal circulation 正循环normal butane 正丁烷normal pentane 正戊烷nozzle size 水眼尺寸nut 螺母Ooff bottom 不接触井底office 办公室oil base mud 油基泥浆oil reservoir 油层on bottom 接触井底open 打开open hole 裸眼opening 扩眼o-ring O环outer barrel 外岩心筒oven 烘箱over pulling 遇卡overshot 打捞筒Ppacker 封隔器packing 密封圈paint 油漆panel 面板paraffin plugging 蜡堵paraffin valve 清蜡闸门paraffin-treatment 清蜡处理paraffin-troubles 结蜡井parts 零件pentane 戊烷PH control additive PH控制剂phenolphthalein 酚酞pile hammer 打桩机pin 销子,公扣pincers 钳子pipe wrench 管子扳手piston 活塞piston rod 活塞杆pit drill 防喷演习pit level 泥浆液面pit level 泥浆池液面pit volume increase 泥浆增加量plastic viscosity 塑性黏度plug 水泥塞plug container 水泥头plug flow 塞流plugging back cementing 回堵注水泥pollution 污染polymer 聚合物portland cement 硅酸盐水泥potassium chlorate 氯化钾power slip 动力卡瓦power source 电源power swivel 动力水龙头power tong 动力大钳power law model 幂律模型pressure decline 压力降pressure equilibrium 压力平衡pressure gage 压力表pressure gradient 压力梯度pressure gradient 压力梯度pressure loss 压力损失pressure loss in pipe 管内压力损失pressure of mud column 泥浆柱压力pressure loss in annular 环空压力损失pressurized air 压缩空气preventer of double ram type 双闸板式防喷器production 生产propane 丙烷pry bar 撬杠，杠杆pull out of the hole 起钻pulley 滑轮pulley 滑轮pulling slip 起卡瓦pumice 浮石pump count 累计泵冲数pump efficiency 泵效pump pressure 泵压pump speed 泵速pump stroke counter 泥浆泵冲数pup joint 短接put into gear 挂挡put on break 刹车，制动PWV(production wing valve) 生产翼阀Qquick coupling 快速接头，快接管箍Rradio operator 电报员radioactivity log 放射性测井rag line 大棕绳rain density 颗粒密度rat hole 鼠洞rate of penetration 转速reamer 释放，丢手reaming 辊轴扶正器recorder 划眼red lead 记录仪reducer 丝扣油，铅油，管件润滑油regular 大小头release 正规扣relief valve 泄压阀,泄流阀reserve pit 储存池reservoir pressure 油层压力retarder 缓凝剂return 返回水泥浆return mud 反出泥浆returning fluid 井口反出液reverse circulation 反循环reverse circulation 反循环revolution 运转revolution 转数revolutions per minute 每分钟转数Reynolds number 雷诺数rig down 拆卸钻机rig up 安装钻机rig in 安装,连接rig out 拆卸ring gasket 钢圈/垫圈riser 隔水导管rope damp 绳头,绳卡rotary hose 泥浆水龙带rotary slip 转盘卡瓦rotary speed 转盘转数rotary table 转盘rotation bases 倒班roughneck 钻工roustabout 水手run casing 下套管run in the hole 下钻run length 进尺run bridge plug 下桥塞run gauge cutter 通井running tool 下入工具running in test 试车running repair 日常修理,现场维修RWTO(returned well to production) 井恢复生产Ssafety belt 安全带safety clamp 安全卡子safety joint 安全接头safety valve 安全阀sampling depth 取样井深sampling interval 取样间隔sand bridge 砂桥sand trouble 砂堵sandline 捞砂绳saturated salt-water mud 饱和盐水泥浆screw 螺钉seal 密封/封堵seating nipple 座落接头sea-water mud 海水泥浆sensor 传感器separater 分离器set back 立根盒setting slip 放卡瓦shaft 轴shale shaker 振动筛shallow gas 试气层shear rate 剪切速度shear pin 剪切销钉sheave 滑轮shock sub 减振器shoe guide 引鞋short trip 短起下钻shut in 关井shut in casing pressure 关井套管压力shut in drill pipe pressure 关井钻杆压力shut in pressure 关井压力shut off 关闭side wall neutron log 井壁中子测井silicon flour 硅粉silicon-controlled rectifier 可控硅整流器single joint elevator 单根吊卡single ram 单闸板slip 卡瓦slip type elevator 卡瓦式吊卡slip velocity 沉积速度slip workline 倒大绳slow pump 低泵速sludge tank 加重泥浆池slush pump 泥浆泵socket 插座solid content 固体含量sonic log 声波测井sonic wave 声波spacer 隔离液spare parts 备件spider 卡盘spontaneous potential log 自然电位测井spool 四通spring 弹簧spud in 开钻squeeze cementing 挤水泥stabilizer 扶正器stabilizing agent 稳定剂stage cementing 分级注水泥stainless steel 不锈钢stand 立柱stand pipe 立管stand the test 试验合格,经受考验standby 待机stand-by boat 值班船starting outfit 启动设备static pressure 静压steam 蒸气sticking 卡钻/被卡stinger 导向插头,引鞋,尾管stinger sub 插入式短节stop lost circulation 堵漏storm 风暴straight well 直井眼sub 接头,短接submerged pump 潜水泵substructure 井架底座sucking line 上水管线suction tank 吸入池supercharge pump 泥浆灌注泵supervisor 监督supply boat 供应船support 支架surge pressure 冲击压力suspending weight 悬重swab pressure 抽吸压力swabbing 抽吸switch 开关TT/B/G 牙齿/轴承/外径磨损table torque meter 转盘扭矩表table height 转盘高度taper milling 锥形刮刀technician 技术人员，技师tee 三通temperature log 温度测井ten minutes gel 终切test paper 试纸thread 丝扣tie back tool 回接工具tighten 上紧TOF(top of fishing) 落鱼顶部tong 大钳tong torque meter 大钳扭矩表ton-mile 吨-英里TOOH(tool out of hole) 起出下入井中的工具tool joint 钻杆接头tool pusher 钻井技师top valve 采油树清蜡闸门,试井闸门torch burner 喷灯torque 扭矩total depth 总井深total gas 气全量total pit 泥浆池总体积tour Shift 班towing 拖航transmission 传动装置/变速器traveling block 游动滑车tri-cone bit 三牙轮钻头trip 起下钻trip tank 计量罐tripping time 起下钻时间tubing 油管tubing hanger 油管挂tubing spool 油管四通tubing head 油管头tubing pressure 油压turbo drill 涡轮钻具turbulent flow 紊流twist off 脱扣typhoon 台风Uunconnect switch 非接触式开关unfreezing 解卡unlatching elevator 开吊卡unloading 卸栽upset 加厚Vvalve master 主阀variable density log 变密度测井V－door 井架大门vent pipe 放空管ventilate 放空,吹扫ventilation 通风,通风设备vertical depth 垂直深度viscosity 黏度volume inside pipe 管内容量volume of annulus 环空容量WW.O.O(wait on orders) 等待指令wait on 等指令wait on cement 候凝wait on(stand by) 待命walkie-talkie 对讲机wall scraper 井壁刮刀WAP(well performance analysis) 井的动态分析warning board 警告牌wash over 洗井,套洗,冲刷wash tank 洗罐,分离罐washer 洗衣机wash-over fishing operation 套洗打捞作业,套洗落鱼作业water flood pump(injection) 注水泵water flush 水循环洗井water injector(injection well) 注水井water lost(WL) 泥浆失水wax containing crude 含蜡原油waxy 蜡,蜡状物,含蜡的WDBS(weight going down before sticking) 仪器遇阻前下行重量weather 气候WEG(wireline entryguide) 喇叭口weight in air 空气中重量weight in mud 泥浆中重量weight indicator 指重表weight material 加重剂weight on bit 钻压weighted mud 重泥浆/加重泥浆welder 电焊工well 井well cleaning 洗井well head 井口well head assembly 井口装置well head pressure 井口压力well shooting 地震测井well bean 井口油嘴well blowout 井喷well bore clean up 洗井,well cementation 固井,挤水泥well cementing operation 固井作业well completing data 完井资料,数据well completing fluid 完井液well completinginformation 完井资料, wellcompleting test 完井测试well completion 完井well condition 井况well control device 井控装置well control equipment 井控设备well control fluid 压井液well control information 井控资料well control manifold 井口控制管汇well control operation 压井作业well deflection 井斜well flow under balance 诱喷well killing 压井well killing job 压井作业well killing method 压井方法well performance testing 系统试井,井动态测试,井生产测试well pulling job 起油管作业well pulling service 修井起下作业well sampling 井下取样well sand up 油井砂堵well screen 油井筛管well service tank 修井液罐well service hoist 修井机well service work 修井作业well site illumination 井场照明well testing supervisor 试油,测试监督well-completion practice 完井作业wellhead cap 井口帽wellhead choke 井口油嘴wellhead control valve 井口总阀门wellhead tap 井口短节wetting agent 润滑剂WHP(wellhead platform) 井口平台wiper trip 通井wire 钢丝wire line(WL) 电缆work accident 操作事故work assignment 工作安排work string reciprocation 工。
教材：石油钻井常用英语手册
A Handbook of English for Oil Drilling石油钻井常用英语手册职工培训教材系列辽河石油勘探局钻井二公司六分公司二OO七年四月A Handbook of English for Oil Drilling石油钻井常用英语手册一、DRILLING 钻井1.Carry out drilling operation in accordance with the drilling program. 按钻井程序进行钻井作业.2.Prepared bell nipple. 准备”喇叭口”短节.3.Make up 2 joints of drill pipe. 接两根钻杆.4.Break out this connection. 卸开该接头.5.Make up bottom hole assembly. 组合下部钻具6.Check and reset crown-saver on every tour. 每个班都要检查并重新调整天车防碰装置.7.Number stands on trip out and trip in. 起下钻时给立柱编号.8.Pick up BHA and run to seafloor. 将下部钻具下到海底.9.Pick up stands. 接立柱10.Don’t drill faster than 15 minutes for 1 stand. 钻进速度别超过15分钟1根立柱11.Drop TOTCO. 投(陶特)测斜仪12.Fish TOTCO with overshot. 用打捞筒捞起测斜仪13.Resume drilling to T.D. 继续钻进到总深14.Circulate 15 minutes.循环15分钟15.Run in hole. 下钻16.Put out of hole. 起钻17.Make an inventory of all ring gaskets. 开一个所有垫圈的清单e spinning tong. 使用气动扳手19.Operate the air winch. 操作气动绞车y down 57 joints of 5” drill pipe. 甩57根钻杆21.Pick up drill stem test tool. 提起钻杆测试工具22.Circulate mud for 2 hours. 循环泥浆2小时23.Move string during circulation. 在循环时注意活动钻具24.Circulate hole clean. 循环清洗井眼25.Circulate bottoms up. 循环泥浆几周26.Fill up every 5 stands. 每5柱灌泥浆一次27.Check mud weight every 15 minutes. 每15分钟检查泥浆比重28.Reverse out excess cement. 反循环替出多余的泥浆29.Change/replace old mud by new mud. 用新的泥浆替换出旧的泥浆30.Stop drilling. 停止钻进31.Drilling ahead. 钻进32.Pull out of hole bit. 起出钻头33.Change bit. 换钻头34.Run the wear bushing. 下抗磨补心35.The bit thread type is regular pin. 钻头丝扣是正规公扣36.What’s the make-up torque? 上扣扭矩要多大?37.Run in 9” collars. 下9”钻铤38.The cathead ca n’t give enough torque. 猫头力量不够39.Connect crossover sub. 接上配合接头40.The tong angle is too small. 大钳的角度太小了41.Stop circulating. 停止循环泥浆42.Break out the stand. 卸立柱43.Set the single into the mousehole. 把这个单根放进鼠洞44.Can we break out the pipe with rotary table? 可用转盘卸扣吗?45.No! Break it out with tong. 不行! 要用大钳卸扣46.Spin it out with the air spanner. 用气动扳手卸扣47.Put the pipe wiper on the string. 装上钻杆刮泥器48.Don’t set this stand back. 这根钻杆不要放在钻杆盒上49.Make up the lift sub. 接好提升短节50.Secure the safety clamp. 上紧安全卡瓦51.The bit is nearing the shoe. 钻头快到套管鞋了52.Slow down the running speed. 放慢下放速度53.This is the undergauged interval. 这是缩径井段54.This is the drilling program. 这是钻井设计书55.How much weight on bit is required? 要加多少钻压?56.Keep the rotary speed at 120---140 RPM. 转速保持120---140转/分57.Keep the flow rate at 3000 LPM. 保持排量3000升/分58.The pump pressure is too high. 泵压太高了59.Don’t ream the hole too fast. 划眼不要太快60.Notice the rotary torque. 注意转盘扭矩的变化61.The penetration rate is getting slower. 钻速变慢了62.The bit is nearly worn out. 钻头快磨光了63.Stop drilling at 2000 meters. 钻至2000米停钻64.Circulate for one hour. 循环一个小时65.The pump pressure has increased. 泵压升高了66.One nozzle may be plugged. 可能有一个水眼(或: 喷嘴)堵了67.What is the hook load? 悬重多少?68.What’s the pick-up weight? 上提重量是多少?69.What’s the lowering weight? 下放重量是多少?70.Run in HWDP. 下加重钻杆71.A stabilizer is needed here. 这里需要一个扶正器72.This is a flexible sub. 这是挠性接头73.This is the BHA log. 这是下部钻具组合记录74.Record all outside and inside diameters. 记录好所有(入井工具的)内外径75.We need a short drill collar. 需要一根短钻铤76.Pull the cat line. 拉猫头77.Operate the break lever. 操作(或:扶)刹把78.Stop the pumps. 停泵79.Make a wiper trip. 通井80.Retrieve wear bushing. 取出抗磨补心81.Bleed off pressure. (释)放压(力)82.Keep 5 wraps on the drum. 滚筒上留5圈83.Set slips. 座上卡瓦84.If tight hole, repeat wiper trip. 如果井眼紧, 重复划眼85.Setback bottom hole assembly. 将下部钻具立于钻杆盒内86.Make sure all alarms are on. 确保所有的警报信号都开着y down TDS spinner. 拆下顶部驱动的旋扣器88.Run in hole bit #15 to bottom. 用15号钻头下钻到井底89.Run in hole to casing shoe. 下钻至套管鞋90.Pick up same bit and BHA. 装上同样的钻头和钻具组合y down 5” HW drill pipe. 甩5”加重钻杆92.Move string every 2 hours. 每2小时活动钻具一次93.Keep area around shaker clean. 保持振动筛区域干净94.Control trip gas. 控制起下钻气95.Ream if needed. 如必要时进行划眼96.Select the best penetration rate. 选择最佳钻进速度97.Fix the traveling assembly. 固定游动系统98.Check power tongs and spinning rope are on drill floor. 检查动力钳和尾绳是否在钻台99.What’s the we ight on bit? 钻压是多少?100.What is the BHA of this well? 这口井的下部钻具如何组合?101.Drill out cement. 钻穿水泥102.Drill out 20” casing shoe. 钻穿20”套管鞋tch the elevator. 扣吊卡104.Unlatch the elevator. 开吊卡105.Set the slips. 放卡瓦106.Adjust the crown-o-matic (crown saver). 调整防碰天车107.Lock the hook pin. 锁紧大钩销子108.Check OD of stabilizer. 检查扶正器的外径109.Perform leak off test. 进行地层破裂(或:渗漏)测试110.Connect kill and choke line. 接上压井和放喷管线111.Reverse out the drill pipe. 反循环清洗钻杆112.Make a short trip. 进行短途起下钻113.Change the cutters. 换割刀114.Slug the pipe. 灌重泥浆115.Drill the stand down. 钻完立柱116.Start/run the shale shaker. 开振动筛117.Start the desanders. 开除砂器118.Start the desilters. 开除泥器119.Change it with a 40 mesh screen. 换成40目筛布120.Shut it off. 关掉121.Pull it to the cat ramp. 把它拉到坡道上去122.Make a fast connection. 接单根要快123.Don’t dump the mud into the s ea. 不要把泥浆排放到海里124.Disconnect it with a chain tong. 用链钳卸开125.Put a thread protector. 加一个(丝扣)护箍126.Can we use the power slips? 可以使用动力卡瓦吗?二、CASING AND CEMENTING 下套管与固井127.R un in hole to bottom for wiper trip. 下钻通井128.T his is the casing program. 这是套管程序129.P repare for running casing. 准备下套管130.M ake everything ready for running 7”casing. 做好下7”套管的准备131.M ake cementing job. 固井132.D isplace cementing with mud pump. 用泥浆泵替泥浆133.S et cement plug from 2940 to 2790m. 在2940到2790米井段打水泥塞134.P ick up cementing head. 接水泥头135.C ement samples are hard. 水泥样已凝固136.P ump in 3 cubic meters of spacer. 注3方隔离液137.P ump down the plug. 泵压(胶)塞138.W ait on cement. 候凝139.T he guide shoe will be connected. 接引鞋140.C onnect the floor collar. 接浮箍141.C onnect the air line to the casing stabbing board. 接好套管扶正台的气管线142.R un casing with the 350T slip elevator. 用350吨卡瓦式吊卡下套管143.C lean and dry 20” casing threads with rags. 清洁并擦干20”套管丝扣144.W here is the rabbit for drifting the casing? 套管通径规在哪里?三、FISHING 打捞145.The bit cutters have been lost in the hole. 牙轮落井146.Run in the reverse-circulation basket. 下反循环打捞篮147.There is a lot of junk in the hole. 井下有很多落物148.The fish is 235.46 meters long. 落鱼长度235.46米149.The fish top is at 2478.34 meters. 鱼顶位置2478.34米四、FREEING STUCK PIPE 卡钻与解卡190.The down-hole problems are very complicated. 井下情况很复杂191.The hole is tight. 遇阻了192.Overpull while tripping out. 起钻遇卡(overpull: 超拉力)193.The formation is unstable. 地层不稳定194.The wall caving is severe. 井壁垮塌严重195.There are many return cuttings. 返出岩屑特别多196.The mud returns have decreased. 返出泥浆减少197.The hole is enlarged. 井眼扩大了198.The pipe’s stuck. 卡钻了199.Pull up to 150 tons. 上提150吨200.Slack off to 50 tons. 下放至50吨201.Ream down all the tight points. 在所有遇阻点进行划眼202.The rotary table can’t rotate. 转盘转不动203.Where is the sticking point? 卡点在哪里204.Make a tensile test. 做拉伸试验205.Back it off above the free point. 在卡点以上倒扣206.Where is the back-off position? 脱扣位置在哪207.Plug the well for side tracking. 打水泥塞侧钻五、ABNORMAL WELL CONDITION AND WELL CONTROL异常井况与压井168.The mud is gas out. 泥浆有气侵169.The pit has lowered quickly. 泥浆池液面下降很快170.The hole lost returns. 井口不返泥浆171.The returns are unstable. 返出泥浆量忽大忽小172.Where’s the thief zone? 漏失层在哪里173.Cut down the flow rate. 降低排量174.Lower the mud density. 降低比重175.Cut down the hydrostatic pressure. 减少静压176.The gas smell is strong. 天然气味度很浓177.There’s some trace of oil. 发现有油花178.The pump pressure is fluctuating. 泵压不稳179.It is a zone of abnormal pressure. 这是异常压力层180.The hole (well) is kicking! 井涌啦!181.Shut in the BOP! 关闭防喷器182.Sound the general alarm quickly! 快发出综合警报183.The stand pipe pressure is 10 kg/cm2. 立管压力10公斤/厘米2184.The casing pressure is 25 kg/cm2. 套压2510公斤/厘米2185.Fill out the kill sheet. 填写压井记录表186.Kill the well. 压井187.Ther e’s a combination of lost returns and the kick. 又喷又漏, 情况复杂188.Reverse the gas out of the hole. 反循环排气189.What’s the lag time? 迟到时间是多少190.The well is now stable. 现在井眼已经稳定六、PREPERATION BEFORE MAKING HOLE钻前准备191.Tell the mechanic to check the motor torque . 让机械师检查马达扭矩。
石油行业常用英语词汇(全面)
石油行业常用英语词汇（全面）1. 石油勘探（Petroleum Exploration）Seismic survey：地震勘探Exploration well：探井Reservoir：储层Porosity：孔隙度Permeability：渗透率2. 钻井与完井（Drilling and Completion）Drilling rig：钻机Bit：钻头Drill pipe：钻杆Casing：套管Cementing：固井Completion：完井Fracking：水力压裂3. 采油与生产（Oil Production and Extraction）Production well：生产井Pumpjack：抽油机Artificial lift：人工举升Separator：分离器Flowline：输油管线Tank farm：储油罐区4. 石油加工（Petroleum Refining）Crude oil：原油Refinery：炼油厂Distillation：蒸馏Cracking：裂化Catalytic reforming：催化重整Asphalt：沥青Lube oil：润滑油5. 石油产品（Petroleum Products）Gasoline：汽油Diesel：柴油Jet fuel：航空煤油Fuel oil：燃料油Petrochemicals：石油化工产品6. 安全与环保（Safety and Environmental Protection）HSE（Health, Safety and Environment）：健康、安全与环境 Spill：泄漏Emission：排放Waste treatment：废物处理Environmental impact assessment：环境影响评估7. 国际合作与市场（International Cooperation and Market）OPEC（Organization of the Petroleum Exporting Countries）：石油输出国组织Brent crude：布伦特原油NYMEX（New York Mercantile Exchange）：纽约商品交易所Spot market：现货市场Futures contract：期货合约本文档为您提供了石油行业常用英语词汇的全面梳理，希望对您的工作和学习有所帮助。
石油专业英语复习资料
石油专业英语复习资料Section 1Petroleum 石油Drilling 钻井Kelly 钻杆String 管汇、管柱Drill pipe 钻杆BHA(Bottom Hole Assembly) 底部钻具组合Sub/joint 接头Collar 钻铤Bit 钻头Finger bit 刮刀钻头Toothed bit 牙轮钻头Diamond bit 金刚石钻头DC 钻铤DS 钻柱Section 2Cat walk 猫道、滑道Cat head 猫头dog house （司钻）休息室、值班室dog leg 狗腿goose neck 鹅颈管monkey board 猴台（二层台）rat hole 大鼠洞mouse hole 小鼠洞fish 落鱼fishing 打捞kick 井涌BOP 防喷器KOP 造斜点Section 3Straight well 直井Directional well 定向井Horizontal well 水平井Extended reach well 大位移井Superdeep well 超深井Underbalance drilling 欠平衡钻井Casing drilling 套管钻井Drilling operations 钻井操作Make a trip/tripping 起下钻Trip up/out 起钻Trip in/down 下钻Make a connection 接单根Completion 固井Completion 完井Logging 测井、录井Derrick system 起升系统Rotary system 旋转系统Draw works 绞车Rotary table 转盘Circulating system 循环系统Muclpump 钻井泵Section 4 Hoisting system 起升系统1 Crown block 天车Traveling block 游动滑车（游车）Hook 大钩Wire line 钢丝绳Derrick 井架2 The type of derrick 井架类型Pyramid derrick 塔式井架Self-elevating derrick 自升式井架Cantilever derrick 前开口井架A-mast derrick A形井架W-mast derrick 桅形井架3 The draw works 绞车刹车Main brake 主刹车Assist brake 辅刹车Band brake 带式刹车Disc brake 盘式刹车Electromagnetic brake 电磁刹车Eaton brake 伊顿刹车Brake band 刹车带Brake drum 刹车筒Pitman 连杆Brake handle 刹把Brake block 刹车块Hydraulic disc brake 液压盘刹Section 5 The rotary system 旋转系统1 Rotary table 转盘Turntable 转台Master bushing 方补心Swivel 水龙头Top drive 顶驱Rotary hose 水龙带Standpipe 立管2 三管goose neck 鹅颈管wash pipe 冲管base pipe/center pipe 中心管3 三轴承main bearing 主轴承upper alignment bearing 上扶正轴承lower alignment bearing 下扶正轴承4 四密封upper machine oil seal 上机油密封lower machine oil seal 下机油密封upper drilling fluid seal 上钻井液密封lower drilling fluid seal 下钻井液密封section 6 The drilling fluid 钻井液1 Mud 泥浆Slurry 水泥浆2 The drilling fluid 钻井液Water base drilling fluid 水基钻井液Oil base drilling fluid 油基钻井液Oil-in water 水包油Water-in-oil 油包水Synthetic drilling fluid 合成基钻井液3 Liquid phase 液相Water 水Oil 油4 Solid phase 固相Clay 粘土Adulterant 加重剂Treating chemical 化学处理剂5 Bentonite 搬土Barite 重晶石Sang content 含砂量Solid phase content 固相含量Colloid 胶体Emulsion 乳状液Foam 泡沫Density 密度Viscosity 粘度Shear 切力Filtration 滤失Viscometer 粘度计Filter press 失水仪Density meter 密度计Section 7 The rig personnel 井队人员编制The rig personnel 井队人员编制Tool pusher 队长Assistant tool pusher 副队长Diller 司钻Secretary 书记assistant diller 副司钻derrickman 井架工roughneck 钻工beach worker 钳工mud man 泥浆工section 8 power and drive system 动力驱动系统1 Power and drive system 动力驱动系统Diesel engine 柴油机Current 电源DC(direct current) 直流电AC(alternating current) 交流电2 The plane of drive 驱动方式Unity drive 统一驱动Unit drive 单独驱动Subunit drive 分组驱动3 Power equipment 驱动设备Mechanical drive 机械驱动Electric drive 电驱动Combination drive 复合驱动Section 9 the actuating system 传动系统1 Type of actuating 传动类型Belt 胶带、皮带Chain 链条Gear 齿轮2 Belt rig 胶带钻机Chain rig 链条钻机Gear rig 齿轮钻机3 Hygraulic drive 液压传动Hygrodynamic drive 液力传动Electric drive 电传动4 Braking 减速Paralleling 并车Astern 倒车Shift 变速Section 10 the control system 控制系统1 The control system 控制系统Air control 气控Air feeder 供气设备Executive element 执行元件Control element 控制元件Assistant element 辅助元件2Air feeder供气设备Air compressor 空气压缩机Air tank 储气罐Air purification equipment 空气净化设备3Excutive element 执行元件Cylinder 气缸Air motor 气马达Air drive friction clutch 气动摩擦离合器Control element 控制元件Pressure control valve 压力控制阀门Temperature control valve 温度控制阀门Flow control valve 流量控制阀门4 Assistant element 辅助元件Antiflocculant 防凝器Alarm 报警器Potating joint 旋转接头Fitting 管汇、管件Section 11 The sub structure system 底座系统1 drilling floor 钻台Derrick 井架Drawworks 绞车Roary table 转盘Pipe setback 立根盒Wellhead tod 井口工具Driller” console 司钻控制台2 control room 机房Power package 动力机组Actuating equipment 传动机组Section 12 The assistant system 辅助系统1Blowout preventer(BOP) 防喷器Kick 井涌、溢流Blowout 井喷Well control 井控Shut well in 关井Kill the well 压井2 BOP 防喷器Rotary BOP 旋转防喷器Annulus BOP 环形防喷器Double ram type BOP 双闸板防喷器Spool 四通Ram type BOP 单闸板防喷器。
石油专业英语常用
石油专业英语常用The Standardization Office was revised on the afternoon of December 13, 2020石油专业英语（常用）油井（oilwell）指任何钻透地球表面（Earth'ssurface）的钻孔（boring），目的是发现（find）或生产（produce）石油（petroleum/oil/hydrocarbons）。
专门生产天然气的叫气井（gaswell）。
油井一般经历五个阶段：计划（planning）、钻井（drilling）、完井（completion）、生产（production）与报废（abandonment）。
首先用钻机（drillingrig）通过钻具（drillstring）上的钻头（drillbit）在地上钻出毫米的孔（hole），然后在钻孔（borehole）中下钢制油管（steeltubing）与套管（casing）。
套管与钻孔之间还可能需要用水泥（cement）来固定。
套管为井孔（wellbore）提供结构上的整体性（structuralintegrity），同时隔离（isolate）危险的高压区（highpressurezone）。
随着井深加大，钻头和套管尺寸会变小。
现在的油井通常都有2-5个逐渐变小的井口尺寸。
钻头通过与之连接的钻铤（drillcollar）来钻进岩层。
钻井液（drillingfluid/mud）通过钻杆（drillpipe）内部泵入钻头，作用包括冷却（cooling）钻头、提升钻屑（drillcuttings）、避免井壁（wellborewall）不稳定以及避免岩层液体由于压力进入井眼。
使用过的钻井液用振动筛（shaker）去掉钻屑后返回泥浆池（pit）循环利用。
通过在地面的顶部驱动装置（topdrive/kellydrive）增加额外的10米长的钻杆（joints）来增加钻井深度。
石油工程专业英语教学内容
第一章石油钻井工程英语基础第1节石油钻井工程基础词汇1.钻探，钻井：drill————拓展记忆钻井：drilling定向斜井directional drilling 欠平衡钻井under-balance 海上钻井off-shore陆地钻井on-land drilling 钻头：drill bit 刮刀钻头：drag bit 牙轮钻头rock bit金刚石钻头diamond bit 喷射钻头jet bit 钻铤drill collar 衣领collar钻杆：drill pipe 钻井队drilling crew 钻机drill rig 钻井泥浆drilling mud钻井液drilling fluid2.油，石油：oil————拓展记忆原有crude oil 石油petroleum 中国石油Petro-China 采油oil production采油设备oil production equipment 采油平台oil production platform 油泵oil pump3.地质：geology————拓展记忆地质专业人员geologist 物理physics地球物理勘探geo-physical probe，geo-physical exploration测井logging 测井作业logging operations 测井记录logging record4.油井：well————拓展记忆井眼hole 油井oil well 试井，油井测试well test 井下down-hole井下作业down-hole operation第2节石油钻井方法基础词汇原油crude oil 天然气natural gas 煤层气coal-bed gas 一体化设计integral design钻井drilling 钻井原理the principles of drilling顿钻钻井percussion drilling，cable-tool drilling 旋转钻井rotary drilling液体冲击fluid percussion 大位移big deviation侧钻井sidetracking drilling technology lateraldrilling水平井horizontal well 探井wildcat，wildcat drilling 深井deep well 浅井shallow well老井maturing well 欠平衡钻井under-balanced drilling 丛式钻井cluster drilling technology 煤层气井coal-bed gas well 生产井production wells 报废井abandon wells停产井non-production wells 绕障井、三维井three-dimensional wells常温井normal temperature well 注采井injection and production well 稠油井heavy oil well热洗井hot washing pipe 井况well condition石油钻井技术基础词汇技术规范，技术指标，技术性能：specification拉伸tension 拉伸强度tension strength 应力stress 压力pressure 应力点stress point压力等级pressure grade 压力降pressure drop 压力梯度pressure gradient回压back pressure 大气压atmosphere 压差differential pressure静液柱压力static fluid column pressure 特征characteristic，feature定性讨论qualitative argiment 定量使用quantitative use液体liquid 固体solid 气体gas，air 正的positive 负的negative虚线dashed line，broken line 实线full line 递减率decline rate 正比于be proportional to 水平的horizontal 垂直的vertical 油层静压the formation static pressure石油钻井参数基础词汇负荷load 扭矩torque 扭转twist 摩擦friction钻压WOB, weight on bit,weight, drilling weight钻速rate of penetration, drilling rate, the rate of drilling, average ROP 钻井周期drilling period 钻速rotary speed 地层压力预测formation pressure prediction technology地层快速预测the formation fast prediction 埋藏深度bury depth产油层，产油带，pay zone，productive formation温度梯度temperature gradient 地层压力formation pressure 坍塌压力collapse pressure破裂压力fracture pressure 平衡压力equilibrium pressure钻具（柱）压力drilling string pressure 钻头振动vibration of bit 钻井成本drilling costs井眼尺寸hole size，well size 参数计算parameters calculation几何参数geometric parameters 参数分析parameter analysis 动态参数dynamic data静态监测static data 注水参数parameter of injection 参数、变量variables 井距well space 垂直深度vertical depth 水平位移horizontal deviation 总深度total depth水平位移horizontal displacement 最大井斜角maximum hole inclination井眼环空annulus space 压力调节器pressure regulator 恢复（增加）压力the build-up pressure 初始开采primary recovery 含水地层water bearing formation 套管漏失casing leak摩擦损失friction losses 气聚阀gas-lift valve 石蜡族paraffin series含气液柱gas-laden column 增产措施stimulation treatment 流动能力flowing capacity生产速率production rate 水驱water drive 气驱gas drive 网状系统grid system水侵water influx 五点法five-spot pattern 油井产量well-productivity 径向流radial system 富气enriched gas 贫气lean gas 气顶gas cap 气驱gas drive（or gas flooding）水驱water drive (or water flooding) 地层伤害formation damage 波及系数sweep efficiency 泄油半径drainage radius 基岩处理matrix treatment 单级脱气single stage separation泄油面积drainage area 表面张力surface tension 束缚力connate water（or interstitial water）石油钻井作业现场工作人员名称1 钻井队drilling crew 队、组crew、team2 技术员technician 钻井技术员drilling technician 泥浆技术员mud technician3 监督supervisor 钻井监督drilling supervisor 副监督assisstant supervisor地质监督geology supervisor4 工程师engineer 泥浆工程师mud engineer 泥浆工mudman机械工程师mechanic engineer 引擎、发动机engine 工程engineering钻井工程drilling engineering 采油工程production engineering石油工程petroleum engineering 试油工程oil test engineering拓展记忆---------------------------工作项目project 希望工程the hope project 三峡工程the Three-Gorge Project项目经理project manager 工程管理project management 钻工：roughneck、floorman司钻driller 副司钻assistant driller 钻井队长drilling foreman 钻井领班tool pusher井架工derrick man 发动机工，机工motorman 钻台工floorman机械师technicians，mechanic 电焊工welder 电工electrician 医生doctor材料员material man，staff man 炊事员cook 翻译interpreter, tansalator洗衣工laundry man石油作业现场常用工具石油作业现场普通工具扳手wrench 螺丝起子screwdriver 多角螺丝起子Phlilips screwdriver活动扳手monkey wrench，adjustable 钳子pliers 手斧hatchet 钩子hook 台钳bench vice 榔头hammer 木锤mallet 搬手spanner 锯子saw 电动手锯jigsaw 电锯power saw钢锯hacksaw 硬尺rule 软尺tape measure 砂纸sandpaper 油漆paint 油漆刷paintbrush 绝缘胶布electrical tape 电线wire 插头plug 电插座outlet 开关switch 螺栓bolt螺帽nut 钉子nail 电钻electric drill 钻头bit 工作台workbench 工具箱toolbox胶水glue 交棒glue bar 管钳pipe tongs，pipe spanner，wrench链钳chain tongs，chain spanner，chain wrench护丝thread protector，screw protector手轮hand wheel 阀门搬手valve wrench，valve spanner 链接法兰coupling flange安全带safety belt 安全帽safety cap 工作靴working boots 千斤顶jack 吊车crane拖拉机tractor 推土机dozer 刮刀scraper1、石油作业现场专业工具接头sub 配合接头X-over，cross-over 提升短接lifting sub，lifting nipple elevator卡瓦slip 母锥box bell 公锥taper tap 短节joint 柔性短节flex joint 井口wellhead螺旋钻铤spiral collar 方钻杆kelly 钻杆架pipe rack 材料房warehouse 绳卡guy anchor 润滑器lubricator 维护保养maintenance 内钳lead tong 外钳back-up tong液压大钳hydraulic tong 兜绳mule line 四通阀four-way valve 软管hose球阀ball valve, globe valve 闸板阀ram valve, gate valve 增压泵booster pump换配件fittings change 灌注泵charge pump第二章石油工程常用设备及专业术语第1节钻井设备部分1 井架derrick 塔形井架derrick A形井架cantilever mast，mast-A 桅杆mast底座大梁sill 架，台rack 架工操作台monkey-board2 游动系统travelling systemn 天车crown block 天车梁crown block beam游动滑车travelling block 钻井大绳drilling line, wire line 金属线, 电线wire，line钢丝绳，测井电缆wire line 金属线，电线wire，line 钢丝绳股strand 截断cutoff滑车，滑轮，皮带轮pulley 吊耳eye plate3 大钩与水龙头hook and swivel 顶驱top drive 大钩hook 大钩弹簧hook spring大钩销子hook pin 大钩环hook ring 大钩锁紧装置hook locking device大钩悬挂高度hook height 水龙头swivel 鹅颈管gooseneck 冲管wash pipe水龙头盘根swivel packing 钻井水龙带drilling hose，rotary hose，kelly hose 立管stand pipe 高压管线high pressure line 低压管线low pressure line 放压管线relief line储气筒gas holder，air holder4 转盘rotary table 转盘方瓦master bushing 方补心kelly drive bushing方孔square openning 小鼠洞mouse hole 大鼠洞rat hole （井架大门处）坡板ramp5 绞车drawworks，hoist 液压绞车hydraulically-powered winch 气动绞车air operated hoist 绞车hoist，windlass，drawworks 滚筒线轴卷轴reel pool drum滚筒高速气离合器drum high air clutch 滚筒低速气离合器drum low high clutch猫头cathead 液压猫头hydraulic cathead 上扣猫头make up cathead卸扣猫头make out cathead 牙嵌离合器jaw clutch 应急牙嵌离合器emergency jaw clutch涡磁刹车eddy current brake 猫头轴cathead shaft 猫头绳cathead line猫头绳爪cat line grip 死绳dead line 死绳固定器deadline anchor死绳固定器膜片dead line diaphragm 上扣spin up，screw on 卸扣，卸开break out, screw off 上紧，固定tighten 松开，松扣loosen 加载load 卸载unload 拧紧screw 拧松unscrew 刹者brake 刹车总成brake assembly 刹车轴brake axle，brake shaft 刹车带brake band刹车片brake band lining 刹车杆brake bar 闸瓦brake block 刹把break crank，brake bar刹车鼓brake drum 离合器clutch 液压油箱hydraulic reservoir液动试压泵hydraulic test pump 液压大钳hydraulic tong 倒档齿轮reverse gear第2节钻井泵类及相关设备泥浆泵mud pump，drilling pump，slush pump 活塞piston 活塞杆piston rod活塞皮瓦piston cup 缸套liner，pumpliner 凡尔体valve body 凡尔座valve cup阀弹簧valve spring 阀杆valve lever 阀面valve face 阀帽valve bonnet泥浆泵安全阀mud relief valve 排出阀discharge valve 吸入阀suction valve潜水泵submersible pump 阀门valve 阀盖valve cap 阀座valve seat 回压阀回压阀back pressure valve 单向阀check valve single-pass valve 安全阀safety valve手动阀manual valve 液动阀hydraulic valve 冷缸cold cylinder 拉杆tie rod，tension bear 上水头intake，suction end 排出口discharge spout 高压管high pressure压力表pressure gauge 冲数strokes 排量displacement，discharge capacity，flow rate第3节井下泵类及相关设备泵筒pump barrel 柱塞plunger 关闭shut down 尾管tail pipe 抽油杆sucker rod长冲程long stroke 低泵速small pumping speed 泵充满度the fullness efficient of the pump 抽油杆sucker rod 排气方法gas bleeding method 泵效pump efficiency三维空间three dimensional space 有效生举efficient lift for the deviated抽油杆扶正工具sucker rod centralization tools 严重的管杆偏磨serious string partial wear游动阀the travelling valve 固定阀the standing valve 部分磨损、偏磨partial wear无杆泵rodless pump 小泵深抽small pump deep pumping technology挂泵深度pump setting depth 尾管长度length of liner 管柱结构the structure of pipe string防脱器dropout-prevent device 井斜角hole angle 电热杆borehole electric heating rod稠油开采heavy oil production 空心杆热载体hollow sucker rod heat carrier变扣器方补芯bushing 终端器terminal assembly 空心抽油杆hollow sucker rod整体电缆传感器continuous cable，sensor 空心光杆hollow polish rod 悬挂器hanger防喷盒stuffing box第4节采油设备采油树Christmas tree 抽油机pumping unit 往复运动reciprocating motion泵杆pumping rod 机械传动mechanical transmission 载荷能力peak polish rod load系统效率system efficiency 冲程stroke length 冲次frequency of stroke无级可调smooth regulation 沉降式抽油泵the sinking sand pump 泵下沉砂sinking砂颗粒sand particles 胶质沥青gum asphalt含蜡量paraffin content 凝固点solidification point 热流hot fluid 参水mingle water第5节与泵操作有关的使用短语没有压力no pressure 压力过高the pressure is too high 返回太少mud return is few水太少water is little 抢修rush to repair 请看记录please read the record没作记录no record 加化学小品put in chemicals 加高岭土粉put in koaline powder加云母片put in mica sheet 加增粘剂put in viscosifier 加稀释剂put in diluent（thinner）加稳定剂put in stabilizer（stabilizing agent）加烧碱put in caustic soda测定比重measure gravity，gravity test 测定失水test filtration 测定切力measure force开关switch 停泵stop the pump 请打手势please make a gesture转动一周turn round a circle 垫高一些put something under it to raise 抓紧firmly grasp抬高lift it up 拿稳hold firm 打一下strike once 往下拉pull out站稳stand firm take a firm hand 小端small end 大端large end 光滑smooth粗糙rough,coarse 平面plane，flat 弯曲winding，bending 放松loosen绷直stretch tight，draw tight 撬棍pinch bar，pry bar 充氨气nitrogen aeration 气包snubber 冷却cooling 润滑lubricate 过载overload 功率不足inadequate power，power is not enough第6节钻台与底座钻台drilling floor，derrick floor，rig floor 钻井记录drilling record司钻监视器driller’s monitor 司钻控制台driller’s console 指重表weight indicator转盘rotary table 卡瓦slip 吊卡latch elevator 底座substructure 井队活动房bunkhouse 钻台上值班房doghouse 立根盒setback （place）立根盒容量setback capacity井控设备well-control device第7节防喷器万能防喷器versatile blowout preventerBag type BOP单闸板防喷器single ram preventer 双闸板防喷器double ram preventer 闸板pipe ram全封闭式防喷器blind ram 蓄能器energy accumulator 压井管线kill line 入口inlet出口outlet 演习drill 消防演习fire drill 防喷演习BOP drill防腐涂料油管anti-corrosion coating material tubing 多功能管柱multi-function string第三章钻井工程作业部分第1节钻井事故泄漏leak 漏失fluid loss 出砂sand production 井喷blow out 井涌kick，flow off井漏lost of circulation，circulation lost坍塌，井壁坍塌caving，cave in，collapse出砂sand production，sand flow 桥塞bridge plug 砂桥sand bridge 井堵well clogging卡钻sticking 卡钻杆sticking the pipe 卡钻具sticking the drill stem 打捞fishing打捞工作fishing job 侧钻side-tracking 侧钻井眼sidetracking hole水泥窜槽cement channeling 固井失败cement failure 防砂sand control，sand-proof第2节钻头牙轮钻头rock bit，tooth-wheel bit 刮刀钻头drag bit 金刚石钻头diomand bit镶齿钻头tungsten carbide bit，insert bit 喷射钻头jet bit 铣齿钻头milled bit 牙轮cone钻头装卸器bit breaker 钻头直径bit diameter 钻头寿命bit life 钻头规格bit gauge钻头磨损bit wear 钻头型号bit type 水眼尺寸nozzle size 水眼效率nozzle efficiency钻头接头bit sub第3节钻具方钻杆kelly 方钻杆旋转短节kelly spinner 方钻杆考克（旋塞）kelly cock 接头sub钻头接头bit sub 钻具drill stem，drilling string 钻杆drill pipe 管子tube，pipe钻具组合drilling assembly 扶正器stabilizer，centering guide 翼状扶正器wing stabilizer扩眼器reamer drill collar 无磁钻铤drill collar 加重钻杆heavy weight drill pipe近钻头扶正器near-bit stabilizer 绕性接头flexible joint 震击器jar 减震器shock absorber 螺旋钻铤spiral drill collar 键槽破坏器key seat reamer 安全接头safety joint钻杆刮泥器drill pipe wiper 配合接头crossover sub 减震器shock sub井下钻具组合BHA-bottom hole assembly泥浆动力钻具mud motor 管线tubeline 钻柱drill string 涡轮tubine涡轮钻具turbo-drill stem 斜度taper，slope 塔式钻具tapered drill stem 接头 a joint，sub 管接头a joint of pipe 立根stand，a stand，thribble 加厚upset 内加厚internal upset外加厚external upset 内外加厚internal-external upset 丝扣thread 母扣box 公扣pin左旋螺纹left-hand thread 右旋螺纹right-hand thread 正规接头regular joint贯眼接头full hole joint 内平接头internal flush joint 护丝thread protector丝扣油thread dope，thread oil 打捞篮junk basket 打捞工具fishing tool打捞管柱fishing string 打捞公锥fishing nipple 打捞颈fishing neck 打捞头fishing head 打捞作业fishing operation 打捞母锥fishing socket 牙轮打捞器cone fisher倒扣工具reversing tool 卡瓦打捞筒slip socket 铣鞋milling shoe 铣具milling tool平底铣鞋flat bottom mill 磁力打捞工具magnetic fishing tool 套管打捞矛casing spear打捞矛fishing spear 打捞钩fish hook 套管打捞筒casing bowl 动力扳手power wrench动力大钳power tong 大钳活动牙块hinged jaw 大钳锁销latch 大钳悬臂suspension unit 气动工具pneumatic tool 打捞震击器fishing jars 打捞缓冲器fishing bumper sub打捞环die collar 打捞筒overshot 打捞短节junk sub 卡瓦slips 刮井器scatcher刮眼器扩井器wiper 油位检查丝堵oil lever check plug 油位oil lever油尺oil-lever dipstick 加油孔lubrication hole 盘根盒stuffing box 井筒工具well bore tool 配套工具matching tools 滚轮扶正器idler wheel centralizer 减磨短节friction reduction sub 轴线加压hydraulic thruster 扶正器centralizer 防脱器、装置anti-slip device减磨扭矩接箍torque-reduction sub 减扭接头torque reduction sub轴向水力加压工具hydraulic thruster 下套管漂浮接箍casing floating coupling轴向加压器hydraulic thruster第4节钻井工程地面作业实用词汇与短语方入kelly-in 方余kelly-up 开钻spud in，starting drilling 作业指令working instruction起钻POOH=pull out of the hole 下钻run in the hole 起下钻make a trip 短起下钻short trip 通井wiper trip 起下循环一周round a trip 循环时间round time，circulating time换钻头change bit 甩钻具laydown 填井pack-hole封井packed drilling发生故障break down 接单根connection 放卡瓦set slip，setting slip，起卡瓦pull slip扩眼openning 划眼reaming 二层台double monkey board，runround 顶部驱动器top drive 吊环bail 吊卡elevator 安全卡瓦safety slips 接头sub adapter 短节sub substitute井下震击器downhole（bumper）jar，down well shaker 打捞工具fishing tool三片卡瓦three slips，three pieces 补芯bushing 方补芯kelly drive bushings转盘补芯（大方瓦）rotary drive bushing 转盘刹车rotary brake 丝扣油thread lubricant oil 刹把brake crank，brake bar，brake lever 脚踏开关pedal switch 挂档put into gear拉猫头cathead 内钳back-up tongs 外钳lead tongs 气动大钳pneumatic tongs 液压大钳hydraulic tongs 机械手mechanical arm 铁钻工machine hand 司钻房driller room有故障it has broken down, it has something wrong 已修好the breakdown has been fixed马上去go there at once 请下去please go down 请上来please come up躲开，危险get out，danger 请翻译来ask the interpretor to come here 冲洗flushing井口well-head（well head）井下落物fish 一根钻杆（单根）single（pipe）三根钻杆组合（立根）thribble 甩单根breaking down 接单根make a connection气动绞车pneumatic drawworks 吊篮basket 卡子clamp 绳套rope sling loosening紧固tightening 挪开move it off 换班change，shift 保养设备maintain equipment钻井日志boring journal，boring log 油管悬挂器tubing hanger第5节钻井工程井口作业实用词汇与短语喇叭口bell mouth，flare opening 贮能器accumulater 液压阀hydraulic valve液压管hydraulic hose 阻流管choke line 井控管汇well control manifold泄压阀pressure relief valve 调压针阀pressure regulating needle valve回压阀backpressure valve 井口螺丝the bolt of wellhead 井口绞车well head drawworks水刹车water brake，hydraulic brake 电缆（electric）cable 井口压力wellhead pressure隔水导管conductor riser 小心滑倒Guard against slipping 不要掉下去Take care not to fall down 我来清理let me clean up 带把扳手来bring a spanner，please 带把铁锤来bring a hammer，please. 带点密封剂bring a little sealant，please 带个密封圈bring a sealing washer 用起子撬prize with （using）screwdriver 用手推注push by hand 卸下来了it has been removed off 装配好了it has been assembled 很快就好了it will be finished right away抬一下let’s lift it 上紧螺丝tighten the screw loosen 松开螺丝loosen the screw把绳子给我give me the rope，please 把绳子拿走take the rope away。
石油钻井工程现场常用专业英语词汇
1. DRILLING ENGINEERING 钻井工程1.1 THE COMPENTS OF THE ROTARY DRILLING RIG钻机系统的组成1.1.1 Hoisting System 提升系统sub structure 井架底座，底部结构derrick (mask) 井架crown block 天车traveling block 游动滑车wire line (drill line) 钢丝绳，钻井大绳deadline 死绳air hoist 气压提升机，气压提升绞车drilling rig (drilling machine) 钻机drawwork 绞车drum 滚筒brake crank (handle, bar) 刹把hydraulic brake 水刹车electric brake 电磁刹车mechanical friction device 机械磨擦装置cathead 猫头elevator 吊卡slip type casing elevator 卡瓦型套管吊卡pipe elevator 钻杆吊卡slip 卡瓦safety slip 安全卡瓦collar rotary slip 环形钻铤转盘卡瓦drill pipe rotary slips 环形钻杆转盘卡瓦links 连杆hook 大钩hook load 大钩负荷hook speed 大钩速度hook weight 大钩悬重DF (drill floor) 钻台monkey board 二层台1.1.2 Circulating & Solids Control System 循环及固控系统drilling mud (drilling fluid) 钻井泥浆，钻井液water mud 淡水泥浆water-base mud 水基泥浆salt mud 盐水泥浆salt-base mud 盐水基泥浆oil-base mud 油基泥浆oilemuision 油包水泥浆，石油乳浊液mud property 泥浆性能mud weight out/in 泥浆密度进/出mud density out/in 泥浆密度进/出mud viscosity 泥浆粘度mud conductivity 泥浆电导率mud resistivity 泥浆电阻PH-value PH值water loss 失水sand content 含砂量gel strength 静切力mud cake 泥饼mud cake effect 泥饼效应mud filtrate 泥浆滤液mud loss 泥浆漏失mud column 泥浆液柱mud sample 泥浆试样mud stability 泥浆稳定性mud pump (pump) 泥浆泵pump body 泵体pump capacity (discharge) 泵排量（泵容量）pump displacement 泵排量pump output 泵排量pump efficiency 泵效率pump stroke 泵冲程pump cylinder 缸套mud pump rod 泥浆泵拉杆piston 活塞mud room 泵房mud line 泥浆管线choke line 地面管汇high pressure line 高压管线standpipe 立管standpipe valve 立管闸门hose 水龙带swivel 水龙头swivel bail 水龙头吊环swivel sub (joint) 水龙头接头swivel stem 水龙头中心管gooseneck 鹅颈管wash pipe 冲管wash pipe swivel 冲管旋转接头kelly 方钻杆kelly cock 方钻杆上旋塞kelly dog nut 方钻杆下旋塞HWDP height weight drillpipe 加重钻杆DP drillpipe 钻杆DC drill collar 钻铤spiral collar 螺旋钻铤pony DC (collar) 短钻铤NMDC non-monel collar 无磁钻铤tool joint 钻具接头sub (joint) 接头tool joint box 接头母扣tool joint pin 接头公扣X-O (crossover) subs 配合接头（转换接头）shock sub 减震接头bumper sub 缓冲器接头bit sub 钻头接头dart sub 投入式止回阀阀座flex sub 柔性短接string stabilizer (pin ×box) 钻具扶正器（公扣对母扣）near bit stabilizer (box ×box) 扶正器（母扣对母扣）centrallizer 扶正器bumpers (shock absorber) 减震器drilling junk basket 随钻打捞杯drilling jar 随钻震击器jar 震击器BHA bottomhole assembly 下部钻具总成HDRT high data rate tool 高速数据传输钻具（MWD用）drill stem (drill string) 钻柱bit 钻头drag bit (blade bit) 刮刀钻头cone bit (roller bit) 牙轮钻头tri-cone bit 三牙轮钻头jet bit 喷射式牙轮钻头core drilling bit 取心钻头milled tooth bit 铣齿钻头insert bit 镶齿钻头gauge insert bit 保径镶齿钻头diamond bit 金刚石钻头bit cone 钻头牙轮bit size 钻头尺寸bit cost 钻头成本bit record 钻头记录bit type 钻头类型bit jets 钻头水眼bit nozzle 钻头喷嘴TFA total flow area 钻头水眼总流量面积bit consumption 钻头用量bit footage 钻头进尺bit factor 钻头因素bit grading 钻头磨损等级bit-tooth dullness 钻头牙齿磨钝程度bit life 钻头寿命bit HHP hydraulic horsepower 钻头水马力hole opener 扩眼器underreamer 管下扩眼器annular 环空wellhead 井口flowline 架空管线shale shaker 震动筛mud tank (mud pits) 泥浆罐suction pit 进口罐setting pit 沉砂罐waste pit 泥浆坑desander 除砂器desilter 除泥器degasser 除气器mud cleaner 清洁器centrifuge 离心机agitator 搅拌机1.1.3 Rotary System 旋转系统prime mover 原动机diesel engine 柴油机engine 引擎rotary table 转盘rotary base 转盘底座rotary chain 转盘传动链条KB kelly bushing 方钻杆补心roller type bushing 滚子方补心master bushing 转盘补心slip type casing spider 卡瓦型套管卡盘tongs 大钳，吊钳lead tongs 内钳back-up tongs 外钳hydraulic tongs 液压大钳chain tongs 链钳pipe tongs (spanner) 管钳spinning chain 旋链power tongs 动力大钳spanning wrench 旋转扳手1.1.4 Blowout Prevention System 防喷系统kick 井涌blowout 井喷blowout control 井控blowout control equipment 井控设备blowout hookup 防喷装置BOP blowout prevention 防喷器annular ram prevention （万能）环形防喷器pipe rams （半封）闸板防喷器blind rams 盲板全封式防喷器shear rams 剪切闸板式全封防喷器blowout plug 防喷塞blowout preventer of three stage packer 三级密封式防喷器control console 控制台remote control console 远程控制台conductor line 导管choke line manifold 节流管线fill line 灌浆管线kill line 压井管线emergency line 紧急压井管线chokes 节流阀hydraulic valve 液压阀gas buster 泥气分离器poor boy 泥气分离器choke pressure 节流压力blowout prevention procedure 防喷措施1.1.5 Motion Compensation System 运动补偿系统offshore floating rigs 海上浮式钻机drillstring compensator 钻柱补偿器sea level 海平面sea floor 海底deck 甲板air pressure vessels 空气压力容器hydraulic cylinder assembles 液压缸总成piston rod 活塞杆standard hook assembles 标准大钩总成riser 隔水导管guideline tensioner 导索拉紧装置control panel 控制盘guide base 导引底盘marine riser 海中隔水导管moon pool 月形开口riser tensioner 隔水导管拉紧装置1.2 W ELLS & DRILLING CRAFT 井与钻井工艺流程well, drilling well 井，钻井wildcat well 预探，初探井delineation well 探边井development well 生产井，开发井satellite well 丛式井injection well 注水井direction well 定向井deviation well 斜井COST continental offshore stratigraphic test well（美）大陆近海地层探井to rig up 安装（钻机）to install the equipment 安装设备to get drill pipes in order 排钻具to measure & inspect drillstring 仗量，检查钻具to measure the length of drill pipes &drill collars 量钻杆，量钻铤to nipple up BOP 装封井器to spud in 开钻to turn on the pumps 开泵to circulate, circulation 循环circulate to the bottom up 完全循环reserve circulation 反循环bit break-in procedure 磨合钻头reaming 扩眼drilling 钻进coring drilling 取心钻进rough drilling (bouncing of drilling tool) 跳钻bit bouncing 蹩钻reverse rotation (running) 打倒车correct drift 纠斜lost circulation 井漏slough (cave-in) 井塌to stop the pump 停泵PC pipe connection 接单根make a joint 接单根wire line survey 吊测deviation survey 测斜to change the shaker screen 换筛布to repair the pump 修泵to break down a joint 卸一个单根to slug the pipe 往钻杆内打重泥浆POOH to pull out of hole 起钻to trip out the hole 起钻touch sticking 遇卡pulling a piston 拔活塞to lubricate rig (drawwork) 保养钻机（绞车）to repair rig 维修钻机to cut & slip the drillline 倒大绳to clean the mud tank 清罐well logging, E-log 电测SWC sidewall coring 井壁取心DST drill stem test 钻杆中途测试to running casing, casing 下套管surface casing 表层套管intermediate casing 技术套管liner 尾管to running cementing 固井to squeeze cement 挤水泥WOC wait on cement 侯凝to nipple up BOP 换装封井器to install the BOP 装封井器to test BOP 封井器试压to change bit, bit change 换钻头RIH run in hole 下钻to trip in 下钻touchdown, touching resistance 遇阻RTO round trip operation 起下钻作业short tripping 短起下钻reaming 划眼to cement plug , plug back 打水泥塞side tracking 侧钻to kick off 造斜KOD kick off depth 造斜深度KOP kick off point 造斜点to hang up 意外停机to survey the flowout 监测溢流flow check 溢流检查WOO wait on order 等指令WOW wait on weather 等天气WOL wait on logging 等测井WOE wait on equipment 等设备WOFT wait on fishing tools 等打捞工具to finish drilling 完钻to running the liner 挂尾管to plug-back 填井final testing 完井测试to install the Chirstmas tree (production) 装采油树well completion 完井to prevent sticking 防卡to prevent caving 防塌to prevent loss of circulation 防漏to prevent blowout 防喷1.3 SPECIAL ENGINEERING OPERATION 特殊工程施工1.3.1 Coring 取心1.3.1.1 Coring Equipment 取心及岩心分析设备coring drill 取心钻具core drilling bit 取心钻头core bit 取心钻头coring crown 金刚石取心钻头core cone bit 牙轮取心钻头core basket 岩心爪core barrel catcher 岩心抓取器core catcher 岩心爪core catcher case 岩心爪外套core gripper 岩心爪core-gripper with slip 卡瓦式岩心爪core-gripper with slipcollar 卡箍式岩心爪core-gripper with slipspring 卡簧式岩心爪core spring 岩心卡簧core barrel 岩心筒core container 内岩心筒core chamber 岩心室core barrel head 岩心筒上盖core barrel ring 取心筒垫圈core shoe （压力式）取心筒鞋core plunger 岩心推取杆core pusher 岩心推取塞core fisher 井底岩心打捞器core picker 落井岩心打捞器core bag 岩心袋core box 岩心盒core tray 岩心盒core house 岩心存储室core storage 岩心库core library 岩心库core breaker 岩心切断器core slicer (splitter) 岩心切断器core-drying oven 岩心烘箱core cutter 岩心切片机core distillation apparatus 岩心蒸馏仪core interpreting device 岩心分析仪core laboratory 岩心分析实验室1.3.1.2 Core Drilling Operation 取心钻进作业core hole 取心井core boring 取心钻进core drilling 取心钻进cored-up mould 岩心造型coring depth 取心井深coring footage (run) 取心进尺coring weight 取心钻压coring formation 取心地层core grouting 取心被卡core breaking 割断岩心core breaking by hydraulic pressure 投球液压割心core breaking by mechanical loading 机械加压割心1.3.1.3 Core Analysis 岩心分析core-analysis data 岩心分析数据core data 岩心数据core log 岩心录井core graph 岩心图core cross section 岩心横剖面core-description graph 岩心描述图core sample 岩心样core wafer 岩心薄片core size 岩心尺寸core orientation 岩心方向core inlet face 岩心入口面core outlet face 岩心出口面core diameter 岩心直径core factor 岩心系数core grinding 岩心磨削core wash 岩心冲蚀core intervals 取心井段core footage (run) 取心进尺core recovery 岩心收获率core porosity 岩心空隙度core oil saturation 岩心含油饱和度core permeability 岩心渗透率1.3.2 Directional Well Drilling & Deviation Survey 定向钻井和井斜监测directional well 定向井directional hole 定向井directional drilling 定向钻井directional drilling contractor 定向井承包商directional MWD 定向随钻测量directional drill tool 定向钻井工具directional orientation tool 定向工具the steering tool 定向工具deflecting tool 造斜工具directional-survey tool 定向测量工具direction finder 测向仪direction instrument 方向仪directional tool (steering tool) 随钻测斜仪inclinometer 测斜仪single shot inclinometer 单点测斜仪syphon inclinometer 虹吸测斜仪continuous inclinometer 连续测斜仪gyroscope 陀螺仪pendulums (plumb bob) 测棰magnetic compass 磁螺盘directional turbodrill 定向涡轮钻具directional bit 定向钻头directional-type tricone bit 定向三牙轮钻头directional clinograph 方位测斜仪deviation replot 井斜图side track 定向设计剖面图horiz projection 水平投影图vertical projection 垂直投影图projection on a vertical plane 垂直面上的投影图deviation map 井斜图perspective view 透视图3 dimensions visualisation 三维空间透视图directional diagram 方位图deviation report 井斜报告directional data 井斜数据surveys 井斜数据deviation measurement data 井斜测量数据directional line 方向线main direction 主方向E.W.S.N 东，西，南，北directional control 方位控制directional characteristics 方位特征directional accuracy 方向性精度directional elements 定向要素direction parameter 方位参数horizontal plane 水平面vertical plane 垂直面directional angle 方位角the drift angle 井斜角the azimuth 方位角bearing (north) 方位角angle of projection 投影角desired drift angle 设计的造斜角the bottom hole coordinate 井底坐标coarse coordinates 水平位移坐标the vertical depth 垂直深度KOD kick off depth 造斜深度end off deviation vertical depth 稳斜结束时的垂直深度end kick off vertical depth 结束造斜时的垂直深度final re-entry depth 恢复点的深度average angle method 平均角度法radius of curvature method 曲率半径法KOP kick off point 初试造斜点end of kick off 造斜终点end of deviation 斜井段终点re-entry point 返直点dog leg 井斜度，狗腿角dog leg scale 狗腿度比例dog leg severity 狗腿严重程度angle build up 增斜angle drop off 降斜dog leg at kick off point 增斜率dog leg at re-entry point 降斜率the actual well path 井眼轨迹1.3.3 Casing 下套管casing 套管casing joint 套管单根，一节套管casing starter 入井第一节套管casing nipple 套管短节casing string 套管柱casing tally 套管记录casing type 套管类型casing weight 套管重量casing size 套管尺寸casing diameter 套管直径casing length 套管长度casing volume 套管容积casing grade 套管钢级casing depth 套管深度casing setting depth 套管下入深度casing accessories (hardware) 套管附件casing guide shoe 引鞋casing float shoe 套管鞋casing shoe depth 套管鞋深度casing centralizer 套管扶正器casing collar 套管接箍casing check valve 回压凡儿casing float (collar) 回压凡儿casing sub 套管异径接头casing head 套管头casinghead spool 套管头四通casing landing 联顶节casing job 下套管作业casing running(installation) 下套管casing-bearing formation好套管下入地层casing appliances 下套管工具casing connection 套管连接casing elevator 套管吊卡casing slip 套管卡瓦casing spider 套管卡盘式吊卡casing suspender 套管悬挂器casing hanger 套管悬挂器casing screw protector 套管公扣护丝casing screw head 套管母扣护丝casing seal 套管密封件casing annular 套管环空casing-to-hole annular 套管井壁环空casing pressure 套管压力casing head pressure 套管头压力casing pressure test 套管试压casingless completion 裸眼完井casing inspection 套管探伤casing programme 套管程序casing severing 割套管casing sticking 套管被卡casing wear 套管磨损casing split 套管裂纹casing leak 套管漏casing imperfection 套管缺陷casing failure 套管损坏casing damage 套管损伤casing deformation 套管变形casing corrosion 套管腐蚀casing collapse 套管挤坏casing buckling 套管弯曲casing bridge plug 套管桥塞casing bowl 套管打捞筒casing collar location 套管接箍测定器casing corrosion monitoring 套管腐蚀监测casing knife 套管割刀casing mandrel 胀管器casing mill 套管铣鞋casing packer 套管封隔器casing perforator 套管射孔器casing section mill 套管铣刀casing splitter 套管割刀casing withdrawal 拔套管1.3.4 Well Cementing 固井open hole 裸眼井cased hole 套管井pocket 口袋the pocket volume 口袋体积normal volume 正常体积extra volume 额外体积hole description 井眼描述string / casing description 钻柱和套管描述surface cement line description 地面水泥管线描述cement 水泥number of sacks 水泥袋数cement factor 水泥系数volume of the cement 水泥体积cement mark 水泥标号cement brand 水泥牌号cement filtrate 水泥滤液cement slurry 水泥浆cement paste 水泥浆cement milk 水泥浆slurry in string 钻柱内水泥浆cement slurry volume 水泥浆体积（用量）slurry excess 水泥浆余量slurry density 水泥浆密度cement column 水泥浆液柱cement consistency 水泥浆稠度cement flow 水泥浆液流cement additive 水泥添加剂additive name 添加剂名称bentonite 膨润土additive volume 添加物体积cementer 粘结剂cement accelerator 水泥促凝剂cement hardener 水泥速凝剂cement agent 粘结剂cement concrete 水泥混凝土cement-water ratio 水灰比cement operation (jobs) 固井作业cement method 固井方法first stage cementation 一级注水泥two stage cementation 二级注水泥multi-stage cementation 多级注水泥liner cementation 衬管注水泥cement equipment (unit) 固井设备cementing tool 固井工具cementing pump 固井泵cementing pump skid 撬装注水泥泵组cementing tank 水泥罐cement blender 水泥搅拌器cement mixer 水泥搅拌器cement practice 固井施工cement squeeze work 挤水泥作业cementing formulation 注水泥配方cement point 封固段cementing through 全井封固seal liquid (spacer fluid) injection 注隔离液cementing injection 注水泥浆chasing 替浆cement displacement 替浆cementing reaction 胶结反应cement setting 水泥凝固cement curing time 水泥候凝时间cementing strength 水泥强度cemented up 注完水泥cement basket 水泥伞cement casing head 水泥头cement mantle 水泥环cement plug 水泥塞cement sheath 水泥壳cement evalution log 固井质量评价测井cement needle 凝固强度检测针cement top 水泥顶界cement thickness 水泥环厚度cement bond log 水泥胶结情况测井cement bond 水泥胶结cementation factor (exponent) 胶结系数cement-formation interface 水泥-地层界面cement job quality 固井质量cement failure 固井不合格cement cap 悬空水泥塞cement channeling 水泥串槽cement contamination 水泥侵cement cut 泥浆水泥侵cement dehydration 水泥浆脱水1.4 THE APPLICATION PROGRAM OF ENGINEERING PARAMETERS工程参数应用程序1.4.1 BIT 钻头initialize run 钻头初始化运行new bit initialization 新钻头初始化bit report 钻头报告bit cost report 钻头成本报告drilling data 钻进数据报告well string data 钻具数据BHA bottom hole assembly 下部钻具组合bit list 钻头列表the bit general data 钻头一般参数bit performance 钻头性能bit characteristics 钻头特征bit number 钻头编号the last drilled bit 上一个钻头bit type 钻头类型drilling cost 钻进成本rig cost 钻机作业成本final cost on drilling time 钻进时间里最终钻头成本final cost on time in hole 钻头入井最终成本minimum bit cost 最小钻头成本FFA total flow area 钻头总截流面积nozzle’s area 水眼尺寸nozzle efficiency 水眼效率bit run , footage 钻头进尺bit progress, run length 钻头进尺individual bit run 单个钻头进尺depth interval 井段，井深间隔average over the run 钻头平均运行参数expected run 钻头预计进尺drilling time 钻进时间off-bottom time 钻头提离井底时间the final wear 钻头最终磨损total revolutions 钻头总旋转圈数the bit manufacture 钻头制造商1.4.2 HYDRAULICS REPORT 水力学报告hydraulics computation 水力学计算Bingham formula 宾汉公式power law formula 幂次律公式power law exponent 幂律指数Reynold’s number 雷诺数the friction factor 磨擦系数the mud system 泥浆系统mud system parameter 泥浆系统参数mud name 泥浆名称flow out 泥浆出口流量computed flow 计算流量measured flow 测量流量critical flow 临界流量optimize flow 优化流量mud density 泥浆密度the equivalent mud density 当量泥浆密度PV plastics viscosity 塑性粘度YP yield point 屈服点GEL strength 静切力MW mud specific weight 泥浆比重mud velocity 泥浆速度nozzles speed 水眼流速a critical velocity 临界流速the actual velocity 实际流速rheological model 流变模型rheological equation 流变方程flow behavior 流性flow type 流动类型laminar flow 层流turbulent flow 紊流Binghamien fluid 宾汉流体Newonient fluid 牛顿流体Pseudo-plastic fluids of Ostwold 奥式假塑性流体the shear stress 切应力the shear rate 切率consistency index 稠度系统a hole cleaning efficiency 井眼净化程度pressure losses 压力损失annular pressure losses 环空压力损失total presses losses 总压力损失pressures losses of laminar flow 层流压力损失pressures losses of turbulent flow 紊流压力损失surge and swab pressure 抽吸和冲击压力bit hydraulic horsepower 钻头水马力mud lag time 泥浆迟到时间cuttings lag time 岩屑迟到时间cuttings size 岩屑尺寸cuttings density 岩屑密度cuttings removal 岩屑上返the slip velocity of cuttings 岩屑下滑速度the relative slip velocity 相对滑动速度drag coefficient 牵引系数annular parameter 环空参数well hole and string parameter 井眼和钻具参数VAN volume of annular 环空体积open hole 裸眼段casing 套管段liner 尾管段FANN graph 范氏图1.4.3 KICK CONTROL 井控，压井well kick , well blowout 井涌，井喷the origin of a kick 井涌起因formation pressure 地层压力the mud column pressure 泥浆液柱压力the invading fluid 地层侵入流体the influx fluid 侵入井眼的流体circulating pressure 循环压力kick report 井涌报告，压井报告initial data 原始数据circulating data 循环数据killing of a well 压井driller’s method 司钻法压井balance bottom hole pressure method 平衡井底压力法压井kick killing data 压井数据the depth of the kick 井涌出现的井深kick size 井涌体积kick tolerance 井涌极限influx density 侵入液密度numbers of circulation cycles 循环周期数the initial mud weight 初始泥浆密度the required mud weight (density) 压井所需泥浆密度resulting mud weight 最终泥浆密度baryte density 重晶石比重heavy mud density 重泥浆密度the adding products 加重材料，添加材料adding rate 加重速度available quantity 储备量，available volume 可使用的体积slow pump stroke 低泵速泵冲the shut in drill pipe pressure 关井钻杆内压力well head maximum working pressure 井口最大工作压力casing burst pressure 套管崩环压力the minimum formation fracturation pressure 最小地层破裂压力expected surface pressure 预期地层压力initial circulating pressure 初始循环压力final circulating pressure 最终循环压力the maximum allowable surface pressure 最大允许地面压力hydrostatic pressure inside pipe 钻杆内静水压力casing pressure 套管压力initial bubble pressure 初始冒泡压力shoe pressure 套管鞋压力displaced volume 排液体积the trip margin 起下钻边界1.4.4 OPTIMIZATION DRILLING 优化钻井WOB weight on bit 钻压RPM the rotation speed 转速the drilling rate 钻进速度the same type of formation 同类型地层a lithological change 岩性变化formation abrasiveness 地层研磨性参数abrasive formation (layer) 研磨性地层drillability factor 可钻性因素formation drillability factor 地层可钻性因素reliable field data 可靠的现场数据the lowest drilling cost 最低钻井成本five-spot drill-off test 五点钻速法optimum WOB 优化钻压值bit weight exponent 钻压指数optimum RPM 优化转速值expected footage 预期进尺expected rate 预期钻速zero drilling rate 零点钻速initial rate of penetration 初始钻速average rate of penetration 平均钻速expected rotating time 预期钻头旋转时间normalized bit tooth height 标准的钻头牙齿高度tooth wear rate 钻头牙齿磨损速度tooth dull 钻头牙齿钝化程度tooth wear 钻头牙齿磨损值bit bearing life 钻头轴承寿命bearing dull 钻头轴承钝化程度the normalized bearing wear 校正的钻头轴承磨损值bit exponent 钻头指数rotating time 钻头旋转时间total rotating hours 总旋转小时数round trip time 起下钻时间bit starting depth 钻头启用井深the optimum parameter 优选参数IDAC code international association of drilling contractors国际钻井承包商协会钻头编号1.5 DRILLING TROUBLES & FISHING 钻井复杂情况与打捞lost circulation, mud loss 井漏，循环漏失kick, gas kick, well kick 井涌well blowout 井喷well slough (cave-in) 井塌drilling string not well braked 溜钻percussion drill 顿钻damaged bit 钻头损坏broken teeth 断牙齿lost nozzle 掉水眼lost cone 掉牙轮lost bit 掉钻头bit balling, balling up of a bit 钻头泥包drilling pipe breaking 断钻具touchdown, touching resistance 遇阻touch sticking 遇卡stuck (sticking) 卡钻drill pipe sticking, sticking of tool 卡钻differential sticking, wall sticking 粘卡key-seating sticking 键槽卡钻sand bridge sticking 砂桥卡钻sand settling sticking 沉砂卡钻fishing tool & process agent 打捞工具releasing stuck agent, 解卡剂black magic, pipe lax 解卡剂sticking point instrument 卡点测定仪plugging agent, sealing agent 堵漏剂lost circulation additive (material) 堵漏添加剂，堵漏材料heavy weight additive 加重剂weighting material 加重物weighted mud 加重泥浆chemical cutter 化学切割器drill pipe cutter 钻杆外切割器casing cutte 套管内切割器washover backoff connector tool 套铣倒扣工具overshot, bell socket 卡瓦打捞筒washover pipe 套铣筒washover shoe 套铣鞋reverse circulating basket 反循环打捞篮drilling junk basket 随钻打捞篮catchall (junk catcher) 一把抓fishing tap 公锥box tap 母锥milling taper 铣锥mill (milling) shoe 铣鞋mill shoe 磨鞋impression block 铅印trip spear (bulldog) 打捞矛wireline spear 电缆打捞矛bend drill pipe 弯钻杆fishing magnet 强磁打捞器key seat wiper 键槽清除器key seat reamer 键槽扩大器stabbing guide 对扣引鞋fishing & other operation 打捞和其它作业to soak with black magic 泡解卡剂breakouting pack of dynamic 爆破松扣washover 套铣make-up (stab) 对扣thread making 造扣back-off 倒扣kill-job, well killing, well control 压井kill job 压井作业1.6 RIG TYPES & OTHER EQUIPMENTS ONWELLSITE钻机类型与其它井场设备1.6.1 Rig Types 钻机类型land, onshore 陆地，陆上swampy 沼泽地带shallow 泻湖区coastal area , offshore 沿海地区，海上drilling rig, drilling machine 钻机cable rig 顿钻钻机cable tool drilling unit 顿钻钻井设备mechanical drilling rig 机械钻机direct-current motor drive drilling rig 直流电动钻机onshore (land) rigs 陆上钻机offshore rigs 海上钻机drilling platform 钻井平台ODP offshore drilling platform 海上钻井平台Jack-up 自升式平台fixed platform 固定式平台SEMI-submersible 半潜式平台self-elevating drilling platform 自升式钻井平台self-elevating offshore drilling platform 自升式海上钻井平台piled steel platform 钢柱支撑平台gravity structure platform 重力结构平台drilling barge, barge 钻井驳船，驳船drillship 钻井船deck (main deck) 甲板，主甲板delipad (helideck) 直升机停机坪steel jacket 钢制导管架1.6.2 Other Equipment on Wellsite 井场其他设备the top drive unit 顶部驱动装置mouse hole 大鼠洞rathole 小鼠洞cellar 圆井pipe slacking block 钻杆盒driller’s console 司钻控制台drilling line reel, drum 大绳滚筒，滚筒the doghouse 钻台值班房，偏房the tool box (possum belly) 工具箱tools of wellhead 井口工具wrench 扳手B.O.P closing unit 封井器控制台wire line stand 大绳架catwalks 大门前跑道personal elevator 乘人电梯wellsite, drilling site 井场the drilling office 钻井办公室the company office 公司办公室pipe racks 钻杆架parts storage 配件房work shop 车工房tool house 工具房water tank 水罐trip tank 起下钻灌泥浆罐mud lab 泥浆房S.C.R house 可控硅房cable tray 电缆排cable elevator 电缆架generator house 发电房electric generator room 发电房gas flare 放喷管线点火处1.7 FIRE PROTECTION, SAFETY & ENVIRONMENTAL PROTECTION消防，安全与环保1.7.1Fire Protection 消防fire goods inflammables 易燃物inflammable material 易燃物explosive gas 易爆气fire damp 沼气gas, nature gas 煤气，天然气inflammable 易燃物品，易燃油品fired charge 引爆炸药fire alarm 火警fire alarm system 火灾报警系统fire detector 火灾探测器fire monitor 防火监控器fire safety system 防火安全系统fire control unit 消防设备fire control equipment 消防器材fire protection equipment 放火设备fire truck 消防车fire-entry suit 消防衣fire apparatus 灭火器fire extinguisher 灭火器fire extinguisher agent 灭火剂fire foam 灭火泡沫fire foam producing machine 泡沫灭火器fire escape 安全门fire exit 太平门fire door 防火门fire gate 放火闸fire ax 消防斧fire hydrant ,fire-plug, 消防栓fire bucket 消防桶fire bank 消防堤fire bulkhead 放火墙fire-fighting rack 消防梯fire sand 消防砂fire fighting boat 消防船fire boat 消防艇fire water line 消防供水管线fire department 消防局fire house 消防站fire brigade 消防队fire-fighting crew 消防队fire fighter , (fire man) 消防员fire patrolman 火灾巡警fireboss 瓦斯检验员firebug 纵火犯firer 放火者fire drill 消防演习fire control 防火fire failure 火灾事故fire hazard 火灾危险性fire insurance 火灾保险fire report 火灾报告fire performance 耐火性能fire resistance 耐火性fire resistance rating 耐火等级fire permit 用火许可证fire prevention code 防火法规1.7.2Safety 安全security 安全safe area 安全区safe atmosphere 安全空气环境safety operation area 安全工作区safe distance, safety clearance 安全距离safe allowance stress 安全许可最大应力safe bearing load 安全负荷safe concentration 安全浓度safety measure, safety precautions 安全措施safety code, safety regulation 安全规程safety guide 安全指南safety clause 保护条款safety guide procedure 防护措施safety-check, safety inspection 安全检查safety education 安全教育safety factor, coefficient 安全系数assurance coefficient 安全系数margin of safety 安全限度potential safety hazard 安全隐患safeguard procedure 防护措施safe rules 安全制度safe operation 安全操作safe practice 安全规章safety analysis technical 安全分析技术safety program 安全程序safety record 安全记录safety voltage 安全电压safety weight 安全重量safe working pressure 安全工作压力safety device , equipment 安全设备safety alarm device 安全报警设备safety checker, safety detector 安全检测器safety apparatus 保险装置safety appliance 防护用具safety grounding device 安全接地设备safety valve 安全阀safety sensor 安全传感器safety switch 安全开关safety belt, safety band 安全带，保险带safety-strap 保险带safety chain 安全链safety board 安全工作台safety cable 保险索safety shelf 安全架safety hat, safety helmet 安全帽protective cap 安全帽safety clothing 安全服safety goggles 护目镜safety shoes 安全鞋safety notice 安全标志safety color 安全色标safety flare 安全照明灯safety lamp 安全灯safety screen 安全罩safety lighting 安全照明safety fuse 安全保险丝1.7.3 Environmental Protection 环境保护environment 环境environmental aspectenvironmental analysis 环境分析environmental administration 环境管理environmental management 环境管理environmental change 环境变化environmental conditions 环境条件environmental criteria 环境标准environmental data 环境数据environmental parameter 环境参数environmental element 环境要素environmental factor 环境因素environmental patter 环境格局environmental effect, environmental impact 环境影响environmental degradation 环境质量下降environmental disruption 环境破坏environmental contamination 环境污染environmental pollution 环境污染waste water, devil water 废水exhaust gas, end gas, waste gas 废气waste product 废物waste liquid, devil liquor 废液off-scum, waste slag 废渣ambient noise 环境噪音environmental extreme 恶劣环境environmental conservation 环境保护environmental control system 环境控制系统environmental control unit 环境控制装置environmental health 环境卫生environmental hazard 环境公害environmental noise 环境噪音environmental protection 环境保护environmental test 环境试验environmental monitoring 环境监测environmental survey 环境检测environmental reconstruction 环境改造environmental temperature 环境温度ambient temperature 环境温度environmental containment standard 环境标准。
石油钻井英语缩写及词汇
石油钻井英语缩写及词汇石油钻井英语缩写及词汇DC: drill collar钻铤DP: drill pipe钻杆HWDP: heavy weight drill pipe加重钻杆X/O: crossover转换接头CSG: casing 套管WOC: wait on cementing侯凝POOH: put out of hole起钻（trip out）短起：short tripRIH: run in hole下钻（trip in）R/U: rig up组装N/U: nipple up组装L/D: lay down甩钻具DD：directional driller：定向司钻（斯伦贝谢的员工）w/: withBOP: blowout preventer防喷器、封井器BHA: bottom hole assembly井底钻具OD: outside diameter外径ID: inside diameter内径IF: internal flush内平FH: full hole贯眼EU: external upset外加厚IU: internal upset内加厚WBM: water base mud水基泥浆OBM: oil base mud油基泥浆TIW: Texas Iron Works全开安全阀MW: mud weight泥浆密度SPP: standpipe pressure立管压力MWD: measure while drilling随钻测量CCL: casing collar log套管接箍测井GR: gamma ray伽马（测井）HTHP: high temperature & high pressure高温高压RPM: round per minute转速SPM: stroke per minute泥浆泵TD: total depth总井深MD: measured depth斜深TVD: true vertical depth垂深PPG: pound per gallonRKB: rotary kelly bushing方钻杆补心GL: ground level地表LCM: loss circulation materials堵漏剂P/U: pick up上提WOB: weight on bit钻压VISC: viscosity泥浆粘度N/D: nipple down拆卸R/D: rig down拆卸SX: sacks袋、包BBL: barrel桶B/U: bottom up循环一周M/U: make up组装LB: poundPSI: pound per square inchESD: emergency shutdown紧急关停装置ROP: rate of penetration进尺速度（机械钻速）ESP：emergency response plan应急响应预案Isolation valve高低压闸门Swab 凡尔提（泥浆泵配件）Hub方卡瓦Bail 吊环Air hoist气葫芦Chain hoist手拉葫芦、倒链V-door (pipe ramp) 斜坡Flowline泥浆天槽Gas buster / poor boy液气分离器Slug pit配浆罐（配药罐）Trip nipple旋转头喇叭口Rotating head旋转头Chickson 活动弯头Trailer/container/cabin/quarter room住井房/生活区Trash pump排污泵Flare pit放喷池/点火池/防火墙pup joint：短节重晶石：bariteWear bushing：防磨套膨润土：gelCasing tally：套管数据Float shoe：浮鞋Float collar：浮匝Protector：护丝WDC：wait on cement：候凝Measure out of hole：校对井深surface casing：表层套管intermediate casing：技术套管production casing：生产套管方瓦：hub卡瓦：slip碳酸钙：calcium carbonate环形防喷器：annular 半封：pipe ram全封：blind ram Drift ：通径（vt）Gauge ring：通径规Resistivity：电阻套压：casing pressure油（管）压：tubing pressure XJH：须家河地层KOP：kick-off point：造斜点。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
石油钻井英语A Handbook of English for Offshore Oil Drilling海洋石油钻井常用英语手册Drilling 钻井Carry out drilling operation in accordance with the drilling program. 按钻井程序进行钻井作业.Prepared bell nipple. 准备”喇叭口”短节.Make up 2 joints of drill pipe. 接两根钻杆.Break out this connection. 卸开该接头.Run hole opener to sea bed. 下扩眼器到海底Mix gel fluid for drilling conductor hole. 为钻导管井眼配制高粘度泥浆.Make up bottom hole assembly. 组合下部钻具Check and reset crown-saver on every tour. 每个班都要检查并重新调整天车防碰装置. Number stands on trip out and trip in. 起下钻时给立柱编号.Pick up BHA and run to seafloor. 将下部钻具下到海底.Pick up stands. 接立柱Don’t drill faster than 15 minutes for 1 stand. 钻进速度别超过15分钟1根立柱Drop TOTCO. 投(陶特)测斜仪Fish TOTCO with overshot. 用打捞筒捞起测斜仪Resume drilling to T.D. 继续钻进到总深Circulate 15 minutes.循环15分钟Run in hole. 下钻Put out of hole. 起钻Make an inventory of all ring gaskets. 开一个所有垫圈的清单Use spinning tong. 使用气动扳手Operate the air winch. 操作气动绞车Lay down 57 joints of 5” drill pipe. 甩57根钻杆Pick up drill stem test tool. 提起钻杆测试工具Circulate mud for 2 hours. 循环泥浆2小时Move string during circulation. 在循环时注意活动钻具Circulate hole clean. 循环清洗井眼Circulate bottoms up. 循环泥浆几周Fill up every 5 stands. 每5柱灌泥浆一次Check mud weight every 15 minutes. 每15分钟检查泥浆比重Reverse out excess cement. 反循环替出多余的泥浆Change/replace old mud by new mud. 用新的泥浆替换出旧的泥浆Stop drilling. 停止钻进Drilling ahead. 钻进Pull out of hole bit. 起出钻头Change bit. 换钻头Run the wear bushing. 下抗磨补心The bit thread type is regular pin. 钻头丝扣是正规公扣What’s the make-up torque? 上扣扭矩要多大?Run in 9” collars. 下9”钻铤The cathead can’t give enough torque. 猫头力量不够Connect crossover sub. 接上配合接头The tong angle is too small. 大钳的角度太小了Stop circulating. 停止循环泥浆Break out the stand. 卸立柱Set the single into the mousehole. 把这个单根放进鼠洞Can we break out the pipe with rotary table? 可用转盘卸扣吗?No! Break it out with tong. 不行! 要用大钳卸扣Spin it out with the air spanner. 用气动扳手卸扣Put the pipe wiper on the string. 装上钻杆刮泥器Don’t set this stand back. 这根钻杆不要放在钻杆盒上Make up the lift sub. 接好提升短节Secure the safety clamp. 上紧安全卡瓦The bit is nearing the shoe. 钻头快到套管鞋了Slow down the running speed. 放慢下放速度This is the undergauged interval. 这是缩径井段This is the drilling program. 这是钻井设计书How much weight on bit is required? 要加多少钻压?Keep the rotary speed at 120---140 RPM. 转速保持120---140转/分Keep the flow rate at 3000 LPM. 保持排量3000升/分The pump pressure is too high. 泵压太高了Don’t ream the hole too fast. 划眼不要太快Notice the rotary torque. 注意转盘扭矩的变化The penetration rate is getting slower. 钻速变慢了The bit is nearly worn out. 钻头快磨光了Stop drilling at 2000 meters. 钻至2000米停钻Circulate for one hour. 循环一个小时The pump pressure has increased. 泵压升高了One nozzle may be plugged. 可能有一个水眼(或: 喷嘴)堵了What is the hook load? 悬重多少?What’s the pick-up weight? 上提重量是多少?What’s the lowering weight? 下放重量是多少?Run in HWDP. 下加重钻杆A stabilizer is needed here. 这里需要一个扶正器This is a flexible sub. 这是挠性接头This is the BHA log. 这是下部钻具组合记录Record all outside and inside diameters. 记录好所有(入井工具的)内外径We need a short drill collar. 需要一根短钻铤Pull the cat line. 拉猫头Operate the break lever. 操作(或:扶)刹把Stop the pumps. 停泵Make a wiper trip. 通井Retrieve wear bushing. 取出抗磨补心Bleed off pressure. (释)放压(力)Keep 5 wraps on the drum. 滚筒上留5圈Set slips. 座上卡瓦If tight hole, repeat wiper trip. 如果井眼紧, 重复划眼Setback bottom hole assembly. 将下部钻具立于钻杆盒内Make sure all alarms are on. 确保所有的警报信号都开着Lay down TDS spinner. 拆下顶部驱动的旋扣器Run in hole bit #15 to bottom. 用15号钻头下钻到井底Run in hole to casing shoe. 下钻至套管鞋Pick up same bit and BHA. 装上同样的钻头和钻具组合Lay down 5” HW drill pipe. 甩5”加重钻杆Move string every 2 hours. 每2小时活动钻具一次Keep area around shaker clean. 保持振动筛区域干净Control trip gas. 控制起下钻气Ream if needed. 如必要时进行划眼Select the best penetration rate. 选择最佳钻进速度Fix the traveling assembly. 固定游动系统100. Check power tongs and spinning rope are on drill floor. 检查动力钳和尾绳是否在钻台What’s the weight on bit? 钻压是多少?What is the BHA of this well? 这口井的下部钻具如何组合?Drill out cement. 钻穿水泥Drill out 20” casing shoe. 钻穿20”套管鞋Latch the elevator. 扣吊卡Unlatch the elevator. 开吊卡Set the slips. 放卡瓦Adjust the crown-o-matic (crown saver). 调整防碰天车Lock the hook pin. 锁紧大钩销子Check OD of stabilizer. 检查扶正器的外径Perform leak off test. 进行地层破裂(或:渗漏)测试Connect kill and choke line. 接上压井和放喷管线Reverse out the drill pipe. 反循环清洗钻杆Make a short trip. 进行短途起下钻Change the cutters. 换割刀Slug the pipe. 灌重泥浆Drill the stand down. 钻完立柱Start/run the shale shaker. 开振动筛Start the desanders. 开除砂器Start the desilters. 开除泥器Change it with a 40 mesh screen. 换成40目筛布Shut it off. 关掉Pull it to the cat ramp. 把它拉到坡道上去Make a fast connection. 接单根要快Don’t dump the mud into the sea. 不要把泥浆排放到海里Disconnect it with a chain tong. 用链钳卸开Put a thread protector. 加一个(丝扣)护箍Can we use the power slips? 可以使用动力卡瓦吗?Casing and Cementing 下套管与固井Run in hole to bottom for wiper trip. 下钻通井This is the casing program. 这是套管程序Prepare for running casing. 准备下套管Make everything ready for running 7”casing. 做好下7”套管的准备Make cementing job. 固井Displace cementing with mud pump. 用泥浆泵替泥浆Set cement plug from 2940 to 2790m. 在2940到2790米井段打水泥塞Pick up cementing head. 接水泥头Cement samples are hard. 水泥样已凝固Pump in 3 cubic meters of spacer. 注3方隔离液Pump down the plug. 泵压(胶)塞Wait on cement. 候凝The guide shoe will be connected. 接引鞋Connect the floor collar. 接浮箍Connect the air line to the casing stabbing board. 接好套管扶正台的气管线Run casing with the 350T slip elevator. 用350吨卡瓦式吊卡下套管Clean and dry 20” casing threads with rags. 清洁并擦干20”套管丝扣Where is the rabbit for drifting the casing? 套管通径规在哪里?Rig Move, Anchoring and Positioning 拖航, 抛锚, 定位What is our position now? 我们现在船位在哪里?What’s the moving speed now? (What’s the towering speed?) 拖航速度是多少? The speed is about 4 knots. 船速是4节左右Which one is the main tug? 主拖是哪条船?The main tug is Nanhai 205. 主拖是南海205Which one is the chase boat? 护航船是哪一条?How much is the horse power? 有多大马力?She has 6000 HP. 有6000马力Move the rig off location 50 feet. 将平台移开50英尺We are ready to drop the anchor. 我们已经做好抛锚的准备了Secure all the movable equipment. 固定好各种活动的设备Preload. (自升式)压载Ballast. (半潜式)压载Put the preload water into the tank. 向压载舱灌压压载水We need 5500 tons of preload water. 需要5500吨压载水Shall we preload right now? 马上开始压载吗?Drain the water off. 放水The rig is overloaded. 平台已超载Jack up (jack down) the rig. 升(降)船The draft is 3.5 meters. 船体吃水3.5米The jetting pressure is 100psi. 冲桩压力是100psiPenetrate the legs. 插桩How much penetration do we have? 入泥多深了?No.1 and No.2 legs indicate 10 meters. 1,2号桩腿插入10米Fix the upper and lower wedges. 固定上下楔块Pay out the anchor line. 放出锚缆绳Skid the derrick. 移开井架The rig is short of potable water now. 平台缺乏饮用水Drop No.2 and No.3 anchors. 抛2号和3号锚Why has the main engine stopped? 主机为什么停?Unleash the drilling tools. 卸开钻具Tighten up. 绷紧(或:上紧)一点Turn on the cooling water for the windlasses. 开锚机刹车冷却水Retrieve the No.1 to No.8 anchors. 起1到8号锚Check the paint marks at the anchor winches. 检查锚机上的油漆记号Prepare for a location move. 准备好移井位Commence anchor handling. 开始起锚(或抛锚)Secure all equipment stored on deck. 固定好所有存放在甲板上的设备Carry out stability and load calculations. 做稳性和载荷计算Pass pendant line, shackle and buoy to anchor handling vessel. 将起抛锚短索, 卸扣和浮标吊起给起锚船Lower the windward anchor to seafloor. 抛上风锚到海底Pick up the leeward anchor first. 先起下风锚Take anchor chaser (or chaser) back to rig. 将捞/抛锚环送回平台Hook up towing lines to tug boat. 将拖缆连接到拖轮Sound fog signal for two seconds every twenty seconds. 发大雾信号, 每20秒钟响两秒Fishing 打捞The bit cutters have been lost in the hole. 牙轮落井Run in the reverse-circulation basket. 下反循环打捞篮There is a lot of junk in the hole. 井下有很多落物The fish is 235.46 meters long. 落鱼长度235.46米The fish top is at 2478.34 meters. 鱼顶位置2478.34米Coring 取芯Stop drilling for coring. 停钻准备取芯Make up core bit. 接取芯钻头What type of core bit is it? 这是什么型号的取芯钻头?Run in a diamond core bit. 下金刚石取芯钻头Let’s drop the ball for coring. 可以投球取芯The core has been broken off. 岩芯断了Put the core in the boxes. 把岩芯装在岩芯盒里Don’t brake suddenly. 不要猛刹车Take out the core. 岩芯出筒How long is the core? 岩芯多长The core recovery is 98%. 岩芯收获率是98%Run in the core barrel again. 继续下岩芯筒(或: 取芯筒)Run in hole core barrel. 下取芯筒Drop ball. 投钢球Recover core. 取出岩芯Use same parameters as for core #1. 使用与1#取芯同样的参数Freeing Stuck Pipe 卡钻与解卡The down-hole problems are very complicated. 井下情况很复杂The hole is tight. 遇阻了Overpull while tripping out. 起钻遇卡(overpull: 超拉力)The formation is unstable. 地层不稳定The wall caving is severe. 井壁垮塌严重There are many return cuttings. 返出岩屑特别多The mud returns have decreased. 返出泥浆减少The hole is enlarged. 井眼扩大了The pipe’s stuck. 卡钻了Pull up to 150 tons. 上提150吨Slack off to 50 tons. 下放至50吨Ream down all the tight points. 在所有遇阻点进行划眼The rotary table can’t rotate. 转盘转不动Where is the sticking point? 卡点在哪里Make a tensile test. 做拉伸试验Back it off above the free point. 在卡点以上倒扣Where is the back-off position? 脱扣位置在哪Plug the well for side tracking. 打水泥塞侧钻Abnormal Well Condition and Well Control 异常井况与压井The mud is gas out. 泥浆有气侵The pit has lowered quickly. 泥浆池液面下降很快The hole lost returns. 井口不返泥浆The returns are unstable. 返出泥浆量忽大忽小Where’s the thief zone? 漏失层在哪里Cut down the flow rate. 降低排量Lower the mud density. 降低比重Cut down the hydrostatic pressure. 减少静压The gas smell is strong. 天然气味度很浓There’s some trace of oil. 发现有油花The pump pressure is fluctuating. 泵压不稳It is a zone of abnormal pressure. 这是异常压力层The hole (well) is kicking! 井涌啦!Shut in the BOP! 关闭防喷器Sound the general alarm quickly! 快发出综合警报The stand pipe pressure is 10 [url=]kg[/url]/cm2. 立管压力10公斤/厘米2 The casing pressure is 25 kg/cm2. 套压2510公斤/厘米2Fill out the kill sheet. 填写压井记录表Kill the well. 压井There’s a combination of lost returns and the kick. 又喷又漏, 情况复杂Reverse the gas out of the hole. 反循环排气What’s the lag time? 迟到时间是多少The well is now stable. 现在井眼已经稳定BOP and subsea Equipment 防喷器与水下设备Cut off the 30” conductor. 割掉30”隔水管Weld on the 30” bottom flange. 焊接30”法兰Hoist and nipple up 30” diverter. 吊装30”转喷器Change the 5” pipe rams to 3-1/2” rams. 把这个5”闸板换成3-1/2”Install blind ram. 安装防喷器的盲板芯子Check the seal ring of the conductor. 检查隔水管密封圈Cut off the lifting eye of the conductor. 切割隔水管耳环Test BOP. 测试防喷器Change annular BOP packing. 更换万能防喷器芯子Full pressure test the ram preventers. 对闸板防喷器进行全压试压Test annular BOP at 2500psi. 万能防喷器试压至2500psiCheck annular pressure. 检查环形空间压力Confirm the angle of the guide base. 确定基板角度The thread is covered with the quick-release protectors. 已戴好快卸护丝Establish the guide lines. 装导向绳Connect the TGB running tool. 接临时导向基板送入工具Land the TGB to sea. 下临时导向基板到海底Retrieve the running tool. 退出送入工具石油钻井英语－－课堂上学不到的内容 2Run the BOP and risers. 下防喷器和隔水管Pick up the marine riser. 吊出隔水管Pick up the slip joint. 起伸缩节Adjust the riser tensioners. 调整隔水管张力Function test the diverter system. 对防喷器系统进行功能测试Retrieve the pin connector. 取出销钉连接器Move the BOP to the moonpool door. 将防喷器移到园井甲板的活动门上Run the test plug. 下试压塞Close the upper pipe ram. 关上部钻杆闸板防喷器Open the kill line valve. 开压井管线阀The compensation capacity is 400000 pounds. 补偿能力是400千磅The locking load is 1000000 pounds. 锁紧负荷1000千磅Support the riser. 接隔水管支撑环Remove the hose bundles. 卸下垮接软管Assure the self-controlled rotation. 保证自控转动Set the LMRP on the test pump. 将下部防喷器插入总成座放到试压桩上Connect the flex joint to the riser. 连接隔水管与挠性接头Land the BOP onto the well head. 座防喷器到井口头Run the subsea TV for monitoring. 下水下电视观察Remove all the riser running tools. 取出所有的隔水管送入工具BOP carrier. 防喷器叉车Lower the universal guide frame. 下放万能导向架Paint mar k the top 6 meters of 30” conductor white. 在30”隔水管的顶部6米处用白漆涂上记号Check adequate length for guidelines. 检查导向绳的长度是否足够Move temporary guide base (TGB) into moonpool. 将临时导向基板到园井甲板Test pull to check connection. 试拉检查连接Grease TGB and running tool as required. 按要求给导向基板及下入工具上黄油Test fit TGB and running tool. 用下入工具试临时导向基板连接Check for junk inside shoe joint. 检查浮鞋内有无落物Pick up 30” conductor handling slings and shackles. 吊上下30”导管的索具和卸扣Is slope indicator properly mounted? 水平仪是否装好?Ensure subsea TV is in good condition. 确保水下电视处于良好的状态Place BOP stack on the test pump. 将防喷器组放在试压桩上Check condition of all 30” casing connectors. 检查所有30”套管接头的情况Replace O-rings as required. 按需要, 更换O性密封圈Attach slope indicator below camera position. 在摄像机下面装上水平仪Inspect and repair diverter. 检查并修理转喷器Prepare spud plate and wireline to check water depth. 准备测深板和钢丝绳测量水深Record all pressure tests on a chart recorder. 用试压表记录试压记录Visually inspect all sealing element. 目视检查所有密封件Check and tighten all bolts. 检查并上紧所有螺栓Bleed off surface accumulators. 地面管线排空气Check for leaks. 检查有无泄漏Lift BOP stack and replace wellhead connector AX ring. 吊起防喷器组并更换连接器AX密封圈Function test wellhead. 对井口头进行功能试验Fill kill and choke valves with seawater. 将压井阀和阻流阀注满海水Pressure test to 500psi then bleed off test pressure. 试压到500psi, 然后放掉压力Reduce hydraulic control manifold pressure to 5200 kpa. 将液压控制管线压力减少到5200千帕Switch to alternate control pod. 把闸门开关倒到控制面板Guidelines are slacked off. 导向绳松了Slack off drill pipe and release running tool. 放松钻杆并卸开下入工具Run subsea TV to observe bit entering the TGB. 下水电视观察钻头是否进入临时导向基板Don’t rotate until hole opener passes through the TGB. 在扩眼器通过临时导向基板前不要旋转Position permanent guide base (PGB) below rotary table. 在转盘下安放永久导向基板Monitor riser level via trip tank. 用计量罐来控制隔水管内的液面Pressure test to 5000psi. 试压5000psiPick up test mandril and place in BOP. 吊起试压防喷器芯子并装入防喷器组Safety and Firefighting 安全与消防Get a Work Permit before you can start the hot work. 办理作业许可证才能进行动火作业Welding is not allowed. 不准动焊Put on your (safety) helmet. 戴上安全帽It’s a high voltage area. 这是高压区That’s against the rule. 这是违章作业Don’t walk under the crane load. 不要在吊物下走动The repairing is under way. 正在检修Keep your hands clear! (Keep you hands off! Do not touch!) 不要乱动Wear and secure your safety belt. 戴上并系好安全带Life jacket must be worn when working outboard or overhead. 舷外或高空作业要穿救生衣Have your breathing apparatus near you. 保持放毒面具在附近It’s a drill. 这是演习It was a BOP drill. 这是防喷演习Get in the lifeboat in order. 按顺序进入救生艇Put on life jacket! 穿好救生衣Abandon the vessel! 弃船Sound the abandonment alarm! 发出弃船警报Go to the helideck! 去飞机坪集合Aboard the lifeboat. 登上救生艇Aboard the supply boat to shore! 乘拖船上岸Check life saving apparatus periodically. 定期检查救生设备It’s for fire fighting. 这是消防用的Start the fire pump. 启动消防泵This rope is too small. 这根绳子太细了It should be function tested. 需做功能测试A warning notice should be set up. 要挂警告牌Do you have an emergency program (contingency plan)? 你们有没有应急计划?It must be ready in an emergency condition. 必须始终保持良好的应急状态Will the typhoon hit our rig? 台风要袭击我们的平台吗?We will have to evacuate the rig. 我们要撤离平台Personnel on board (POB). 在船人员总数Sound fire alarm. 发消防警报This is a fire drill. 这是消防演习conduct abandon ship drill. 举行弃船演习Release the boat hooks. 释放救生艇吊钩Board the life boat. 登救生艇Remove the rust and paint with anti-corrosive primer. 除锈后上防锈底漆Three rafts are located near life boat station port side. 在左舷救生艇站附近还存放有3个救生筏Wear work vests when working below the cellar deck. 在圆井甲板面下面工作时须穿工作救生衣The station bills need to be updated. 应急部署表须更新Check the expiry date for all foam extinguisher. 检查所有泡沫灭火器的过期时间Close all the water-tight doors. 关闭所有水密门Safety procedure shall be followed at all the times. 在任何时候都应遵守安全程序Anchor wires should have a Spelter type socket at anchor side. 抛锚绳靠锚的一端应使用锌压头Colour code all the connection at the loading station. 在供给站管线接头处用颜色表明各管线Verify that a high level alarm is installed on the sludge tank. 确认污水舱安装有高位警报Don’t switch on during drilling operation. 钻井作业期间不能合闸Provide two independent means to start the emergency generator engine. 应急发电机柴油机应有两套独立的起动方法Have the boom pennant wires of port crane re-certified. 重新认证左舷吊车扒杆变幅绳Clean the internals of the emergency switchboard. 清洁应急配电盘内部Helicopter and Supply Vessel 直升机与供应船Load out Contractor’s riser at Zhanjiang anchorage. 在湛江锚地把承包商的隔水管装上平台Offload casing. (从供应船上)卸套管Load (offload or unload) the boat. 装(卸)船Get the food container loaded on the boat. 把食品集装箱装上船The helicopter will land on rig soon. 直升机很快就要在平台降落Tell the base to get (or send) a chopper here. 通知基地派飞机来Helicopters are not allowed to land here. 飞机不能降落Report the weather condition to the pilot. 向飞行员报天气Inform the boat come to standby. 通知拖轮过来待命Call the boat to come along port side. 通知拖轮过来靠左舷We will take the personnel basket. 我们乘坐吊篮Repair and Maintenance 检修Have an overall check. 进行全面检查MPI the brake linkage system. 对刹车连接系统进行磁粉探伤Demonstrate that the make-up cathead can pull 7000 lbs. 证明上扣猫头能拉到7000磅Determine the origin of the air leak and rectify this. 找出漏气的地方并处理Adjust the brake band equalizer beam properly. 适当调整刹带平衡梁Note that the 3000 hour inspection on TDS is due. 注意顶驱的3000小时保养时间已到Check sheave rope pocket wear with a 1 3/8”+1 1/32 template. 用1 3/8”+1/32”量规检查绳槽磨损的情况Repair the handrails on the crown. 修理天车台的栏杆Function test the anti-freefall brake on monthly basis. 每月对天车防碰装置进行功能试验Get me a spanner, please. 请递给我一把扳手Renew brake rim because of excessive wear. 更换磨损严重的刹车鼓Clearly mark safe working load (SWL) on the air winch below the rig floor. 表明钻台底下气动绞车的安全工作负荷Measure the master bushings for wear. 测量主补心磨损情况Have BOP ram opened up for internal inspection. 打开防喷器闸板进行内部检查Install a ground cable on the triplex pump motor. 给三缸泵马达安装接地线We need a 48” pipe wrench. 我们需要一把48”的管钳Strike it with a sledge hammer. 用大锤打We want a triangle file. 需要一把三角锉刀Tighten up the screw. 紧一下螺丝Check it with a level. 用水平尺量一下Put some engine oil. 抹点黄油Have it greased. 给它上黄油Put out of hole test string. 取出测试管串Check all the equipment. 检查所有设备There’s something wrong with it. 有点毛病Rig inspection will be performed in August. 验船安排在8月份Maintain the hoisting system. 保养提升系统Adjust the brake band. 调整绞车刹带Change the oil in the rotary gear box (transmission). 更换转盘变速箱机油Replace one water pump. 倒换一台冷却泵It’s quick-discharge air valve. 这是快速放气阀This clutch needs repair. 这台离合器需修理This tong needs replacing. 这把钳要更换了Slip 6 meters of the drilling line. 滑移钻井大绳6米Cut off 45 meters of the drilling line. 切割大绳45米Check the pump liners and pistons. 检查(泥浆)泵缸套和活塞The piston has been washed. 活塞刺坏了The supercharge pump doesn’t take in water. 灌注泵不上水Regulate the relief valve. 调整安全阀This part number is wrong. 这个配件号不对The multi-pen recorder has some problem. 多笔记录仪坏了Miscellaneous 其他No smoking here. 此处严禁吸烟Everything is OK. 一切准备就绪Speed up please. 请快点The geologist must be present. 地质人员必须到场We have to wait on weather. 必须等候天气There will be strong wind. 有强风Give me a hand, please. 请帮一下忙Do you understand? 明白吗?No way! 不行Man overboard! 有人落水Help! Help! 救命Someone is injured. Medic! 有人受伤了, 医生Call for the medic. 叫医生Get a stretcher please. 拿担架来No more than 4 persons. 不能超过4人Drinking liquor is not allowed. 不许喝酒Don’t overrun your equipment. 不要超负荷运转Be careful at work. 工作时要小心No joking here. 别开玩笑Rig up for logging. 准备电测What is the next step? 下一步怎么办?Get everything ready as soon as possible! 尽快做好一切准备附录一: 平台人员岗位名称一. 承包商人员( Contractor’s Personnel )Rig Manager 平台经理Equipment Supervisor 设备总监Materials Supervisor 材料总监Senior Toolpusher 高级队长Junior Toolpusher 值班队长Driller 司钻Sub Sea Engineer (SSE) 水下工程师Assistant Driller (AD) 副司钻Derrick Man 井架工Floor Man (roughneck) 钻工Barge Master (captain) 船长First Mate (Barge engineer) 大副Control Room Operator (CRO) 压载工Ballast Control Operator (BCO) 压载工Chief Engineer 轮机长Head of Routabout 甲板班长Crane Operator 吊车工Routabout 甲板工Mechanic 机械师Electrician 电气师Repairman 修理工Motorman 轮机员Welder 焊工Radio Operator 电报员Warehouse Man (stock Keeper) 材料员Medic 医生Safety Supervisor 安全监督Interpreter (translator) 翻译Chief Steward 管事Cook 厨师Steward 厨工Laundry Man 洗衣工二. 作业者及服务公司人员( Operator’s Personn el and Service Company Personnel) Drilling Superintendent 钻井监督Company Man (Operator’s Representative) 公司代表Geologist 地质师Mud Logging Engineer (Mud logger) 泥浆录井工程师Sample Catcher 捞砂工Mud Engineer 泥浆工程师ROV Engineer 潜水工程师Cementer 固井工Cement Engineer 固井工程师Testing Engineer 试油工程师Coring Engineer 取芯工程师Wireline Logging Engineer电测工程师附录二: 平台主要设备一. 钻井设备(Drilling Equipment):Drawworks 钻井绞车Rotary Table 转盘Bushing 补心Top Drive System (TDS) 顶驱Swivel 水龙头Crown Block 天车Traveling Block 游车Hook 大钩Derrick 井架Pipe Spinning Wrench 钻杆气动扳手Ezy-Torq 液压猫头Elmagco Brake 涡磁刹车Pipe handling Equipment 钻杆移动设备Iron roughneck 铁钻工Pipe Racking System 钻杆排放系统Drill String 钻柱Drilling Sub 钻井短节Fishing Tool 打捞工具Power Tong 动力大钳Air Winch (air tugger) 气动绞车Crown-O-Matic (Crown Saver) 防碰天车二. 泥浆系统(Mud System)Mud Pump 泥浆泵Shale shaker 振动筛Mud Cleaner 泥浆清洁器Desilter 除泥器Desander 除砂器Degasser 除气器Centrifuge 离心机Mud Agitator 泥浆搅拌器Mud Mixing System 泥浆混合系统Centrifugal Pump 离心泵Standpipe Manifold 立管管汇Rotary Hose 水龙带Bulk Air System and Tank 吹灰系统和灰罐三. 井控设备(Well Control Equipment):Ram Type Preventor 闸板防喷器Annular Type Preventor 万能防喷器BOP Stack 防喷器组Gate Valve 闸阀Choke and Kill Manifold 阻流压井管汇Remotely Operated Panel 远程控制面板Choke Control Panel 阻流控制面板BOP Handling Equipment 防喷器搬运设备Diverter 转喷器四. 海事系统(Marine System)Ballast System 压载系统Bilge System 污水系统Vent 通风口, 通气口Air Supply Fan 供气扇Mooring System 锚泊系统Communication Equipment 通讯系统Jacking System 升降系统Skidding System 井架滑移系统Windlass 锚机Anchor 锚Pendant 短索Buoy 浮标Lifting and Handling Equipment 起吊和搬运设备五. 机房(Engine Room)Diesel Engine 柴油机Emergency Generator 应急发电机Water Maker (desalinization unit) 造淡机Air Compressor 空气压缩机Boiler 锅炉Air-conditioning System 空调系统Sea Water Service Pump 海水供给系统Piping System 管汇系统Generator 发电机Transformer 变压器DC Motor 直流马达AC Motor 交流马达六. 安全设备(Safety Equipment)Fire Control System 消防控制系统Fire Detection System 火情探测系统CO2 System 二氧化碳系统Fixed Fire Extinguishing System 固定消防系统Portable Extinguisher 移动灭火器Fire-Fight Equipment 消防设备Foam System 泡沫系统Lifeboat 救生艇(Inflatable) Life Raft (气涨式)救生筏Davit 吊艇架Escape Routes 逃生路线Breathing Apparatus 呼吸器Life Buoy 救生圈Gas Detection System 气体探测系统Helicopter Facility 直升机设施Sick-Bay (Hospital) 医务室Pollution Control 防污控制七. 其他( Others)Cementing Unit 固井装置Well Testing Equipment 试油设备Mud Logging Unit 泥浆录井房Wire Logging Unit 电测装置ROV 潜水器Meter 米Foot 英尺Inch 英寸Supply Boat (supply vessel) 供应船Standby boat 值班船Day (night) Shift 白(夜)班Crew Change 倒班Crew 船员, 队员, 井队Position 岗位Draft (draught) 吃水Air Gap 空气间隙, 气隙Penetration (桩腿插桩)入泥Evacuation 撤离Rig (Drilling rig) 钻机, 钻井船附录三. 平台场所Bow 船首Stern 船尾Forward (FWD) or fore 船首的Aft 船尾的Port 左舷Starboard (STBD) 右舷Upper Deck 上部甲板Main Deck 主甲板Quarters (living quarters, accommodation area) 生活区Drill Floor (Rig floor) 钻台Bridge (Pilot house, Steerwheel house) 驾驶室Control Room 控制室Helideck 直升机甲板Cementing Unit Room 固井泵房Air Compressor Room 空气压缩机房BOP Control Room BOP控制房Radio Room 报房Engine Room 机房Thruster Room 推进器房Warehouse (Store) 材料库房Paint Room (paint locker) 油漆房库Leg 桩腿Jacking House 升降室Column 立柱Sack Storage Area 散装材料储存区Mud pit 泥浆池Cellar Deck 圆井甲板Riser Rack Area 隔水管排放区Pipe Rack Area 钻杆排放区Pipe Slide 滑道Ramp 坡道Spud Tank 桩脚箱Pontoon 浮箱Moonpool 月池/园井甲板Pump Room 泵房Shale Shaker House 振动筛房Coffee Room 咖啡室Rig Office 平台办公室Mess (dining) Room 餐厅Recreation Room 娱乐房TV RoomChange Room 工衣房Kitchen 厨房附录四. 钻具,井口工具,打捞工具Drill Pipe 钻杆Drill Collar 钻铤Heavy Weight Drill Pipe 加重钻杆Elevator 吊卡Tong 大钳Make-up Tong 上扣大钳Break-out Tong 卸扣大钳Mud Box 泥浆防喷盒Casing Stabbing Board 套管扶正器Slips 卡瓦Spider 卡盘Mouse Hole 小鼠洞(接单根用) Kelly Spinner 方钻杆旋转器Kelly Cock 方钻杆阀Chain Tong 链钳Casing 套管Tubing 油管Drill String 钻柱Jar (drilling jar) 震击器Right Hand Thread 正扣Left Hand Thread 反扣Stabilizer 扶正器Rabit 通管器Liner 尾管Conductor 导管Thread Protector 护丝Stand (钻杆) 立柱Single (钻杆) 单根Joint (钻具) 根Bend 弯头Sub 短节Pup Joint 短钻杆, 短节Connector 接头Bit 钻头Bit Breaker 钻头盒Box 母扣Pin 公扣Hole Opener 开眼钻头Reamer 扩眼钻头Overshot 打捞筒Junk Basket 打捞篮Junk Mill 平头磨鞋Spear 打捞矛Fishing Tap 打捞公锥Cross Over Sub (XO Sub) 转换接头Bottom Hole Assembly (BHA) 下部钻具组合附录五. 材料和工具Steel 钢Iron 铁Wood 木Chemicals 化学品Cement 水泥Barite 重晶石Potable Water 淡水Drilling Water 钻井水Sea Water 海水Fuel 柴油Helifuel 飞机燃油Lubricant (Lube/Lube oil) 润滑油Grease 黄油Thread Dope 丝扣油Ballast Water 压载水Bilge Water 舱底水Gasoline 汽油Mud 泥浆Bentonite 般土Additive 添加剂Caustic Soda 烧碱Weight Material 加重材料Thinner 稀释剂Oxygen 氧气Nitrogen 痰气Hydrogen Sulphide 二氧化硫Acetylene 乙炔Compressed Air 压缩空气Hydraulic Fluid 液压油Spanner 扳手Hammer 铁锤Screw Driver 螺丝刀Multimeter 万用表Welding Machine 焊机Bar 撬杠Shackle 卸扣Sling (钢丝) 绳套Container 集装箱附录六. 常用缩写形式BHA: bottom hole assembly 下部钻具组合DP: drill pipe 钻杆DC: drill collar 钻铤HWDP: heavy weight drill pipe 加重钻杆BOP: blowout preventer 防喷器TD: total depth 总深TVD: true vertical depth (定向井的)垂直深度SCR: silicon controlled rectifier 可控硅OD: outside diameter 外径ID: inside diameter 内径BBL: barrel 桶LB: (拉丁语) Libra=pound (重量单位) PSI: pound per square inch 磅/英寸2 GAL: gallon 加仑POOH: pull out of hole 起钻RIH: run in hole 下钻WOW: wait on weather 等候天气WOC: wait on cement 候凝JU: Jackup 自升式(钻井船)SEMI: semi submersible 半潜式(钻井船)RPM: revolution per minute 转速/分钟LPM: liter per minute 升/分钟KN: knot 节(海里/小时)SWL: safe working load 安全工作负荷API: American Petroleum Institute 美国石油协会IADC: international association of drilling contractors 国际钻井承包商协会MPI: magnetic particle inspection 磁粉探伤。