Powder Selection Guides
C-Lube技术介绍说明书
Before oil impregnation Maintenance Free Linear GuidesC-Lube technology keeps linear motion components lubricated—so you don’t have to!Walk through any plant that uses linear motion systems, and you can often see maintenance workers, grease gun in hand, applying lubrication to linear guides. And why shouldn’t they. Under-lubricated guides can wear excessively, which leads to performance problems and premature failure.These labor-intensive lubrication practices, however, do not come cheap. We estimate that manual lubrication can cost upwards of €500 per grease fitting when you consider the cost of the lubricant itself and the wages of the guy with the grease gun. And that figure doesn’t begin to capture the total cost of manual lubrication when you consider that many grease fittings are difficult to access and service without triggering some downtime.It doesn’t have to be that way. There are a number of linear guides that offer at least some freedom from lubrication routines. You will hear them described as “lubed for life” or “maintenance free” or “self lubricating.”These reduced maintenance guides typically have mechanical designs with provisions for storing and delivering lubricant over long periods of time. To varying degrees, they can drastically reduce or even eliminate the need to apply lubricant beyond what is present when the bearing goes into service.Unlike automated lubrication systems, which can be complex and costly, maintenance free bearings tend to rely on simple, integrated mechanical features in the bearing slider to store and deliver the oil.Various takes on maintenance free guides and ways have been around for years now, but not all of them are created equal. Some focus on achieving the longest possible maintenance free intervals. Others focus on a compact design that adds as little as possible to the size of the bearing’s mechanical package.’s C-Lube linear components have unique designs that balance long service life with compact size. These long-term maintenance free linear motion products comein different forms—including roller guides, ball guides and a ball-spline-based shaft guiding system. They range in size from small, 5mm-wide track rails to 65mm-wide guides that offer a basic static load rating of 765,000 N.Despite the outward differences in these products, they all make use of ’s proprietary C-Lube lubricating elements. Made from sintered resin powder witha steel backing, these C-Lube elements have an open porous structure that canbe impregnated with large amounts of oil (see Figure 1). Depending on the type of linear guide, the C-Lube elements are formed into either a plate or sleeve shapeand integrated into the bearing’s slider. They then release the impregnated oil slowly through direct, continual contact with the linear guide’s internal rolling elements.While thegeometryof thelubricatingelement differsdepending on the type ofguide, in no case doesC-Lube increase the overalldimensions of the guide.In other words, self-lubrication capabilities, at least forproducts, do not increasethe package size of the guide.Because all the C-Lube guides offer the same maintenance free interval, the choice between them comes down to functional requirements such as the type of load and duty cycle. With that in mind, here’s an overview of the different C-Lube variants:•R oller Guides - Designed for applications requiring maximum stiffness and resistance to moment loads, the Linear Roller Way Super MX guides feature a slider that operatesC-Lube Linear WayExternal Lubrication partsIntegrated C-Lube Conventional linear guide T r a c k R a i l S l i d e u n i t s t r o k e d i r e c t i on Cylindrical Rollers C-LubeFor more information on ’s full range of bearings and linear motion products please visit www.ikont.eu or call +31 10 462 68 68• B all-Spline Guides - C-Lube Ball Spline MAG guidesincorporate an internal oil-impregnated plate-shaped element. As the balls traverse over the C-Lube plate, they pick up oil which lubricates both the balls and the spline shaft—again protecting against metal-on-metal contact.• B all Guides - Familiar ball guides, which run on recirculating steel balls, take on a new twist when combined with C-Lube technology. In C-Lube Linear Ways, the steel balls roll through a sleeve made from the C-Lube material. As the balls travel through the sleeve, they pick up oil themselves and alsotransfer it to the rail as they come in contact with it. At all times, the balls and rail remain free from any metal-on-metal contact due to a film of lubricant provided bythe C-Lube feature.2016 N T E /A v R。
朗杰（R-Gen）RV产品说明书
This is a photo of the RP-177 dinette. This dinette has an EZ-Glide table that quickly collapses down to create a 42” X 74” bed. That table can easily be taken outside for entertainment and outside food preparation. This dinette seats four adults and sleeps two adults comfortably.
These are two great appliances of the r-Pod. On the left is the optional convention microwave. On the right is a standard 4.2 cu. Ft. gas/12V/electric DSI refrigerator and freezer combo.
This is a photo of the RP-177. Here is the queen bed with storage beneath (as seen in photo on right).
This is a photo of the RP-178“U-shaped” dinette. This dinette is located in the front of the RV and the table collapses down to create a 58” X 74” bed. The EZ-Glide table can quickly be removed and placed outside for outside cooking preparation and entertainment. This dinette will comfortably sleep two or seat five adults. Look toward the rear of the RP-178 you will find a queen bed with storage below.
Vaddio IN-Wall 摄像头挂载系统说明书
©2014 Vaddio - All Rights Reserved. IN-Wall Enclosures - Document Number 341-744 Rev FIN-W ALL ™ R ECESSED C AMERA M OUNTING S YSTEMS Recessed Camera Mounting Systems for Vaddio™, Sony®, Polycom®, LifeSize®, Cisco® PTZ Cameras and Vaddio™ EZCamera™ Cable System PackagesOVERVIEW:The Vaddio IN-Wall camera mounting systems are an attractive way to mount PTZ cameras on a wall where room aesthetics are critical. These mounting systems use the depth of the wall cavity to minimize the camera’s extension into the room while providing a finished look to the installation. Each system consists of an in-wall mounting box, camera platform and face frame, which are powder coated white, but can be painted to match any décor.IN-Wall Enclosure Supported Cameras and Part NumbersPart Number Compatible Camera Systems 999-2225-018Vaddio ClearVIEW™, PowerVIEW™, WallVIEW™ HD Series or RoboSHOT Series Systems 999-2225-012Vaddio ZoomSHOT and WideSHOT Sony EVI-D70 , Vaddio WallVIEW 70 System 999-2225-014Sony EVI-HD1, Vaddio WallVIEW CCU or PRO HD1 PTZ System, WallVIEW EagleEye 1080 HD and Polycom EagleEye 1080 HD 999-2225-015Polycom EagleEye and EagleEye IV, Vaddio WallVIEW PRO EagleEye, Cisco PrecisionHD, Cisco PrecisionHD 1080p and LifeSize 4X999-2225-016Sony BRC-H700, Vaddio WallVIEW CCU or PRO H700 PTZ SystemSony BRC-Z700, BRC-H900 Vaddio WallVIEW CCU or PRO Z700 PTZ System 999-2225-011Sony EVI-D100, Vaddio Model & WallVIEW 100 System 999-2225-019Sony BRC-Z330, Vaddio WallVIEW CCU or PRO Z330 PTZ System, EVI-D80 EVI-D90, EVI-H100, Vaddio WallVIEW 80 & 90 999-2225-020Cisco Precision 60 999-2225-220 LifeSize 10X PTZIntended Use: Please read the entire manual thoroughly. The IN-Wall Enclosure was designed, built and tested for use indoors and for a particular camera listed above. Mounting the wrong camera in the IN-Wall may create a potentially unsafe operating condition.Save These Instructions: The information contained in this manual will help you install and operate your product. If these instructions are misplaced, Vaddio keeps copies of Specifications, Installation and User Guides and most pertinent product drawings for the Vaddio product line on the Vaddio website. These documents can be downloaded from free of charge.UNPACKING:Carefully remove the product and all of the parts from the packaging and identify the following parts: One (1) Back Box EnclosureOne (1) Camera PlatformOne (1) Face Frame One (1) Set Mounting Hardware and Screws ∙ Four (4) 8-32 X ¼” White Pan Head Screws (for Face Frame attachment) ∙ Four (4) 10-32 x ¼” Flat Head Screws (for Camera Platform attachment)∙ Four (4) Self-Drilling Drywall Anchors∙ Four #8 x 1.25” Screws for Wall Anchors▪ One (1) ¼” x 20 Camera Mounting Screw (for those cameras that use ¼” x 20 screws)-OR-▪ Four (4) M3x6mm Camera Mounting Screws for Polycom EagleEye Cameras (non-Sony)Images: IN-Wall Systems - Top Row (left to right) Vaddio RoboSHOT™ and HD-Series (HD-18/19/20/22/30/USB), LifeSize 10X and 4X, Cisco Precision 60 and PrecisionHD. Bottom Row (left to right): Polycom EagleEye, Sony EVI-D100,EVI-D70,EVI-HD1, BRC-Z330, Sony BRC-Z700 and BRC-H700.Note: Cameras are not included with the IN-Wall mounts.IN-Wall EnclosuresFace Frame attached to back box withfour screws CameraPlatform attached to Back Box with four ScrewsFace Frame (rear view)Deep Back Box EnclosureThe 3-15/16” deep metal wall box uses the maximum depth of a standard 2” x 4” framed wall cavity and minimizes the camera’s protrusion into the room. Each Enclosure is outfitted with three (3) conduit knockouts (2-sides, 1-top) and a cable pass-through in the back box and camera platform.Before InstallingWhen locating the IN-Wall enclosure, consider viewing angles, lighting conditions, possible line of site obstructions and check for in-wall obstructions where the camera is to be mounted (like studs). Pick a mounting location to optimize the performance of the camera. Please read the step-by-step instructions fully before starting the installation.INSTALLATION INSTRUCTIONS:1) Position the back box enclosure against the wall, level the box and trace the outlineof the box on the wall with a pencil.2) After checking for in-wall obstructions, cut out the area marked on the wall with adrywall saw.3) Place the enclosure into the wall opening for a dry fit and mark the four holes forthe spiral wall anchors through the mounting flanges. The integrator can use anywall anchor of their choice or use the supplied wall anchors. Level the back box.Remove the back box and install the wall anchors. Pull the cabling through thewall and back box and push it into the opening. Fasten the enclosure to the wallwith wall anchors.4) On the sides of the face frame, there are four holes (see drawing below) for attaching the Face Frame to the Back Box with the supplied white pan head machine screws.5) Place the Camera Platform onto the bottom of the Back Box, and screw theplatform down with the four flat head machine screws. If using the cablepass-through, thread the cables through the platform. 6) Connect the camera system and push the slack in the cabling back into the wall. 7) Place the camera on the Camera Platform and secure the camera to the platform with the supplied screwsHARDWARE WARRANTY:Please see the Vaddio website at for the Vaddio Statement of Warranty for all Vaddio Products. The Statement of Warranty covers the policies and procedures of the Hardware Warranty, Exclusions, Customer Service, Technical Support, Return Material Authorizations (RMA), Voided Warranty, Shipping, Handling and Products Not Under Warranty. The Vaddio Warranty Statement supercedes all other published warranty statements heretofore in content and coverages. Vaddio Technical Support can be contacted through the Vaddio website or through e-mail support at ******************.EZIM MountingNuts X 2 Use a level to position the enclosure and trace a line around the back of the enclosure once the box is level. Toll Free: 1-800-572-2011, Main: 763-917-4400, FAX: 763-971-4464, ©2014 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing are subject to change without notice or obligation. Vaddio, IN-Wall, RoboSHOT, ClearVIEW, PowerVIEW and WallVIEW are trademarks of Vaddio. All other trademarks are property of their respective owners. Planet HD-189733b in front page header courtesy of Hubble Space Telescope, Document Number 341-744 Rev F, SD: 68314.1 Four Screw holes for mounting theFace Frame to the Back Box。
拴带安装说明书
C2204/FMTPJ01NDCHIMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONSFRONT TIEDOWNS
Minor movement (or settling) can occur in some incidental harsh driving conditions (on or off road).A rubber bed mat is not a requirement to maintain the lifetime warranty on a Torklift sys-tem, but a strong recommendation, simply as a safety precaution to protect the truck bed, the bottom of the camper and to give the camper additional support.
Warning!!TORKLIFT DOES NOT RECOMMEND: Installing your truck camper in your truck on top of a drop in plastic bed liner THIS WILL VOID YOUR WARRANTY!
The drop in plastic bed liners can slide on top of the truck bed surface, and the camper can slide on top of the slick surface of the bed liner. The liner can also act as a spring causing a trampoline effect increasing vertical truck camper movement, independent of the vehicle, possibly resulting in truck bed damage and/or camper damage!UPPER SUPPORT STRAPTRUCK FRAME
Lumber Cutting Guide 产品说明书
Lumber Cutting GuideOWNER’S MANUALWARNING:Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.Thank you very much for choosing this product. For future reference, please complete the owner’s record below:Model: Purchase Date: _______________Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product before you begin using it.This product is designed for certain applications only. The manufacturer or distributor cannot be responsible for issues arising from modification. We strongly recommend that this product not be modified and/or used for any application other than that for which it was designed. If you have any questions relative to a particular application, DO NOT use the product until you have first contacted the distributor to determine if it can, or should be, performed on the product.INTENDED USEThe lumber cutting guide attaches to your chain saw to cut lumber up to 2 x 6s in your own backyard from all types of wood.TECHNICAL SPECIFICATIONSGENERAL SAFETY RULESWARNING:Read and understand all instructions.Failure to follow all instructions listed below may result in serious injury.CAUTION: Do not allow persons to operate or assemble this Lumber Cutting Guide until they have read this manual and have developed a thorough understanding of how the Lumber Cutting Guide works.WARNING:The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions or situations that could occur. It must be understoodby the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.SAVE THESE INSTRUCTIONSWORK AREA•Keep work area clean, free of clutter and well-lit.Cluttered and dark work areas can cause accidents.•Keep children and bystanders away while operating the Lumber Cutting Guide. Distractions can cause you to lose control, so visitors should remain at a safe distance from the work area.•Be aware of all power lines, electrical circuits, water pipes and other mechanical hazards in your w ork area, particularly those hazards below the work surface hidden from the operator’s view that may be unintentionally contacted and may cause personal harm or property damage.PERSONAL SAFETY•Stay alert, watch what you are doing and use common sense when using the Lumber Cutting Guide.Do not use the Lumber Cutting Guide while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating the Lumber Cutting Guide may result in serious personal injury.•Dress properly. Do not wear loose clothing, dangling objects, or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.ASSEMBLY•Timber Tuff’s Lumber Cutting Guide guides your chainsaw down a guide board attached on top of a log. We suggest using 2x4s or 2x6s as guide boards for your lumber cutting guide. If you use a 2x4, attach the adjustable stop bracket (#2) to the lumber cutting guide using bolt (#3) and nut (#4). •Start b y making a 4x4 for practice. Begin by taking a log, about 6” in diameter, and nailing a 2x4 to the top of the log, centered.•After you attach the 2x4 to the log, put the lumber cutting guide on the 2x4. Slide the lumber cutting guide up and down the 2x4 while adjusting the stop angle so it does not bind up. Once theadjustments have been made, fasten down and tighten the lumber cutting guide on the 2x4.•The lumber cutting guide can be mounted to your chainsaw two ways:o Option 1: Use 3 screws (#6) to clamp the lumber cutting guide to your chainsaw bar.o Option 2: Drill 2 holes in your chainsaw bar and use bolt/nut combo (#13) to fasten to your chainsaw bar.•Option 1 makes installation and adjustments quick and easy. You must be careful tightening the screws to avoid damaging the clamp casting. Tighten 1/8th turn each, 2 or 3 times byrotating between the 3 screws until snug on the bar. DO NOT over tighten,•Option 2 eliminates the possible damage to the clamp casting and creates a very secure mount to your chainsaw bar.PARTS DIAGRAMPARTS LISTFor replacement parts and technical questions, please call 1-218-943-6290.WARRANTYOne-year limited parts warrantyBACPO BOX 155Miltona, MN 56354MADE IN CHINA。
关于亚布力滑雪场的英文作文
关于亚布力滑雪场的英文作文Embracing the Slopes of Yabuli: An Exhilarating Winter WonderlandNestled amidst the majestic Changbai Mountains, the Yabuli Ski Resort stands as a beacon of winter wonderment, drawing in skiers and snowboarders from around the world. As the largest ski resort in China, Yabuli has carved out a reputation for its breathtaking landscapes, world-class facilities, and unparalleled skiing experiences. From the moment you set foot on the powdery slopes, you are transported into a realm where the boundaries between man and nature blur, and the pursuit of adrenaline-fueled thrills becomes the ultimate goal.The journey to Yabuli is as much a part of the experience as the skiing itself. The winding roads that lead to the resort offer a tantalizing glimpse of the rugged terrain that lies ahead. As you ascend the mountain, the landscape transforms before your eyes, with lush forests giving way to a pristine blanket of snow that glistens in the sunlight. The anticipation builds with every kilometer, and the moment you catch your first glimpse of the towering peaks, you know you have arrived at a truly special place.Upon entering the resort, the sheer scale of the operation becomes immediately apparent. Yabuli boasts an impressive array of ski runs, catering to skiers and snowboarders of all skill levels. From the gentle beginner slopes to the heart-pounding expert runs, the resort offers a diverse range of terrain that caters to every preference. The well-groomed pistes are meticulously maintained, ensuring a smooth and consistent experience for all who grace the slopes.One of the standout features of Yabuli is its state-of-the-art infrastructure. The resort is equipped with a fleet of high-speed chairlifts and gondolas that whisk visitors up the mountain with ease, minimizing wait times and maximizing time on the slopes. The base area is a bustling hub of activity, with an array of restaurants, shops, and après-ski entertainment options to cater to the needs of every visitor.For those seeking a more immersive experience, Yabuli offers a range of lodging options, from cozy mountain chalets to luxurious hotels. The accommodations are designed to provide a comfortable and convenient base for skiers and snowboarders, with amenities that cater to the needs of the modern traveler. Whether you're looking to unwind after a day on the slopes or indulge in some well-deserved pampering, Yabuli has you covered.One of the true highlights of the Yabuli experience, however, is theopportunity to witness the breathtaking natural beauty that surrounds the resort. The Changbai Mountains, with their towering peaks and pristine forests, offer a stunning backdrop to the skiing and snowboarding activities. During the winter months, the landscape is transformed into a true winter wonderland, with a blanket of snow that covers the terrain and creates a serene and peaceful atmosphere.For those seeking a more adventurous experience, Yabuli offers a range of off-piste and backcountry skiing options. The resort's experienced guides are on hand to lead skiers and snowboarders through the untouched powder, offering a thrilling and challenging experience that is not for the faint of heart. The sense of freedom and exploration that comes with carving through untouched snow is truly unparalleled, and it is an experience that will leave a lasting impression on even the most seasoned of skiers.Ultimately, the Yabuli Ski Resort is a destination that offers something for everyone. Whether you're a seasoned skier or a first-time snowboarder, the resort's world-class facilities, stunning natural beauty, and unparalleled hospitality will ensure that your winter getaway is one to remember. From the moment you step onto the slopes to the moment you reluctantly bid farewell, Yabuli will captivate your senses and leave you craving for more.So, if you're in search of a winter adventure that will truly take your breath away, look no further than the Yabuli Ski Resort. Embrace the slopes, immerse yourself in the stunning natural surroundings, and let the thrill of the mountain take over. It's an experience that will leave you yearning to return time and time again.。
PAX-黄原酸盐 MSDS
1.IDENTIFICATION OF THE MATERIAL AND SUPPLIERProduct Name:POTASSIUM AMYL XANTHATEOther name(s):PAX; Carbonodithioic acid, O-pentyl ester, potassium salt; Potassium pentylxanthate; Potassium isoamyl xanthate.Recommended Use: Mineral floatation.Supplier:Orica Australia Pty LtdABN:99 004 117 828Street Address: 1 Nicholson Street,Melbourne 3000AustraliaTelephone Number:+61 3 9665 7111Facsimile:+61 3 9665 7937Emergency Telephone: 1 800 033 111 (ALL HOURS)2. HAZARDS IDENTIFICATIONThis material is hazardous according to criteria of Safe Work Australia; HAZARDOUS SUBSTANCE.Classified as Dangerous Goods by the criteria of the Australian Dangerous Goods Code (ADG Code) for Transport by Road and Rail; DANGEROUS GOODS.Risk Phrases:Harmful in contact with skin and if swallowed. Irritating to eyes and skin.Safety Phrases: Do not breathe dust. Avoid contact with skin and eyes. In case of contact with eyes,rinse immediately with plenty of water and seek medical advice. Wear suitableprotective clothing, gloves and eye/face protection.Poisons Schedule:None allocated.3. COMPOSITION/INFORMATION ON INGREDIENTSComponents CAS Number Proportion Risk Phrases Potassium isoamyl xanthate928-70-190%R21/22, R36/38 4. FIRST AID MEASURESInhalation:Remove victim from area of exposure - avoid becoming a casualty. Remove contaminated clothing and loosen remaining clothing. Allow patient to assume most comfortable position and keep warm. Keep at rest until fully recovered. If patient finds breathing difficult and develops a bluish discolouration of the skin (which suggests a lack of oxygen in the blood - cyanosis), ensure airways are clear of any obstruction and have a qualified person give oxygen through a face mask. Apply artificial respiration if patient is not breathing. Seek immediate medical advice.Skin Contact:If skin or hair contact occurs, immediately remove any contaminated clothing and wash skin and hair thoroughly with running water. If swelling, redness, blistering or irritation occurs seek medical assistance.Eye Contact:If in eyes, hold eyelids apart and flush the eye continuously with running water. Continue flushing until advised to stop by the Poisons Information Centre or a doctor, or for at least 15 minutes.Product Name: POTASSIUM AMYL XANTHATE Issued: 03/07/2009 Substance No: 000033326701Version: 4Page 1 of 6Ingestion:Rinse mouth with water. If swallowed, give a glass of water to drink. If vomiting occurs give further water. Seek immediate medical assistance.Medical attention and special treatment:Treat symptomatically.5. FIRE FIGHTING MEASURESHazards from combustion products:Substance liable to spontaneous combustion. Avoid all ignition sources. In common with many organic chemicals, may form flammable dust clouds in air. For precautions necessary refer to Safety Data Sheet "Dust Explosion Hazards". Precautions for fire fighters and special protective equipment:Heating can cause expansion or decomposition of the material, which can lead to the containers exploding. If safe to do so, remove containers from the path of fire. Decomposes on heating emitting toxic fumes, including those of carbon disulfide . Fire fighters to wear self-contained breathing apparatus and suitable protective clothing if risk of exposure to products of decomposition.Suitable Extinguishing Media:Coarse water spray, fine water spray, normal foam, dry agent (carbon dioxide, dry chemical powder).Hazchem Code: 1Y6. ACCIDENTAL RELEASE MEASURESEmergency procedures:Shut off all possible sources of ignition. Clear area of all unprotected personnel. If contamination of sewers or waterways has occurred advise local emergency services.Methods and materials for containment and clean up:Wear protective equipment to prevent skin and eye contact and breathing in vapours/dust. DO NOT allow material to get wet. Air-supplied masks are recommended to avoid inhalation of toxic material. Vacuum solid spills instead of sweeping. Collect and seal in properly labelled containers or drums for disposal. Use non-sparking tools.7. HANDLING AND STORAGEConditions for safe storage:Store in a cool, dry, well ventilated place and out of direct sunlight. Store away from sources of heat or ignition. Store away from incompatible materials described in Section 10. Keep dry - reacts with water, may lead to drum rupture. Keep containers closed when not in use - check regularly for spills.Precautions for safe handling:Avoid skin and eye contact and breathing in dust. Keep out of reach of children.8. EXPOSURE CONTROLS/PERSONAL PROTECTIONOccupational Exposure Limits: No value assigned for this specific material by the National Occupational Health and Safety Commission. However, Exposure Standard(s) for decomposition product(s):Carbon disulfide: 8hr TWA = 31 mg/m3 (10 ppm), SkProduct Name: POTASSIUM AMYL XANTHATE Issued: 03/07/2009 Substance No: 000033326701Version: 4Page 2 of 6As published by the National Occupational Health and Safety Commission.TWA - The time-weighted average airborne concentration over an eight-hour working day, for a five-day working week over an entire working life.`Sk' Notice - absorption through the skin may be a significant source of exposure. The exposure standard is invalidated if such contact should occur.These Exposure Standards are guides to be used in the control of occupational health hazards. All atmospheric contamination should be kept to as low a level as is workable. These exposure standards should not be used as fine dividing lines between safe and dangerous concentrations of chemicals. They are not a measure of relative toxicity. Engineering controls:Ensure ventilation is adequate and that air concentrations of decomposition product(s) is/are controlled below quoted Exposure Standards. Avoid generating and breathing in dusts. Use with local exhaust ventilation or while wearing dust mask. Keep containers closed when not in use.Personal Protective Equipment:The selection of PPE is dependant on a detailed risk assessment. The risk assessment should consider the work situation, the physical form of the chemical, the handling methods, and environmental factors.Orica Personal Protection Guide No. 1, 1998: F - OVERALLS, SAFETY SHOES, CHEMICAL GOGGLES, GLOVES, DUST MASK.Wear overalls, chemical goggles and impervious gloves. Avoid generating and inhaling dusts. If dust exists, wear dust mask/respirator meeting the requirements of AS/NZS 1715 and AS/NZS 1716. Always wash hands before smoking, eating, drinking or using the toilet. Wash contaminated clothing and other protective equipment before storage or re-use.9. PHYSICAL AND CHEMICAL PROPERTIESPhysical state:Pellets or FlakesColour:Green or YellowishOdour:IrritatingSolubility:Soluble in water.Specific Gravity:0.75-0.80Relative Vapour Density (air=1):Not availableVapour Pressure (20 °C):Not availableFlash Point (°C):Not availableFlammability Limits (%):Not availableAutoignition Temperature (°C):Not availableMelting Point/Range (°C):>=270pH:Not availableProduct Name: POTASSIUM AMYL XANTHATE Issued: 03/07/2009 Substance No: 000033326701Version: 4Page 3 of 610. STABILITY AND REACTIVITYChemical stability: Stable under normal conditions of use. Hygroscopic: absorbs moisture or water fromsurrounding air. Reacts exothermically with water .Conditions to avoid: Avoid dust generation. Avoid exposure to heat, sources of ignition, and open flame.Avoid exposure to moisture.Incompatible materials: Incompatible with oxidising agents , combustible materials , acids , water , phosgeneor sulphur chlorides .Carbon disulfide. Hydrogen sulfide. Carbonyl sulfide.Hazardous decompositionproducts:Hazardous reactions: Hazardous polymerisation will not occur. Can react with water producing carbondisulfide.11. TOXICOLOGICAL INFORMATIONNo adverse health effects expected if the product is handled in accordance with this Safety Data Sheet and the product label. Symptoms or effects that may arise if the product is mishandled and overexposure occurs are:Ingestion:Swallowing can result in nausea, vomiting, diarrhoea, abdominal pain, convulsionsand loss of consciousness. Death may occur if large amounts are ingested.Eye contact:An eye irritant.Skin contact:Contact with skin will result in irritation. Will liberate carbon disulfide upon contactwith moist skin. Carbon disulfide can be absorbed through the skin with resultantadverse effects.Inhalation:Breathing in dust may result in respiratory irritation. Breathing in high concentrationscan produce central nervous system depression, which can lead to loss of co-ordination, impaired judgement and if exposure is prolonged, unconsciousness.Breathing in high concentrations may result in an irregular heart beat and provesuddenly fatal.Long Term Effects:No information available for the product.Toxicological Data:Oral LD50 (rat): 1000 mg/kg.12. ECOLOGICAL INFORMATIONEcotoxicity Avoid contaminating waterways.13. DISPOSAL CONSIDERATIONSDisposal methods:Refer to Waste Management Authority. Advise flammable nature. Dispose of material through a licensed waste contractor. Normally suitable for disposal at approved land waste site. Material can be recycled.Product Name: POTASSIUM AMYL XANTHATE Issued: 03/07/2009 Substance No: 000033326701Version: 4Page 4 of 614. TRANSPORT INFORMATIONRoad and Rail TransportClassified as Dangerous Goods by the criteria of the Australian Dangerous Goods Code (ADG Code) for Transport by Road and Rail; DANGEROUS GOODS.3342Class-primary 4.2 Spontaneously CombustiblePacking Group:IIIProper Shipping Name:XANTHATESHazchem Code:1YMarine TransportClassified as Dangerous Goods by the criteria of the International Maritime Dangerous Goods Code (IMDG Code) for transport by sea; DANGEROUS GOODS.UN No:3342Class-primary: 4.2 Spontaneously CombustiblePacking Group:IIIProper Shipping Name:XANTHATESIMDG EMS Fire:F-AIMDG EMS Spill: S-JAir TransportClassified as Dangerous Goods by the criteria of the International Air Transport Association (IATA) Dangerous Goods Regulations for transport by air; DANGEROUS GOODS.UN No:3342Class-primary: 4.2 Spontaneously CombustiblePacking Group:IIIProper Shipping Name:XANTHATES15. REGULATORY INFORMATIONClassification:This material is hazardous according to criteria of Safe Work Australia;HAZARDOUS SUBSTANCE.Hazard Category:Xn: HarmfulXi: IrritantRisk Phrase(s):R21/22: Harmful in contact with skin and if swallowed.R36/38: Irritating to eyes and skin.Safety Phrase(s):S22: Do not breathe dust.S24/25: Avoid contact with skin and eyes.S26: In case of contact with eyes, rinse immediately with plenty of water and seekmedical advice.S36/37/39: Wear suitable protective clothing, gloves and eye/face protection. Product Name: POTASSIUM AMYL XANTHATE Issued: 03/07/2009 Substance No: 000033326701Version: 4Page 5 of 6Poisons Schedule:None allocated.This material is listed on the Australian Inventory of Chemical Substances (AICS).16. OTHER INFORMATIONThis material safety data sheet has been prepared by SH&E Shared Services, Orica.Reason(s) for Issue:5 Yearly Revised Primary MSDSChange to Transport InformationThis MSDS summarises to our best knowledge at the date of issue, the chemical health and safety hazards of the material and general guidance on how to safely handle the material in the workplace. Since Orica Limited cannot anticipate or control the conditions under which the product may be used, each user must, prior to usage, assess and control the risks arising from its use of the material.If clarification or further information is needed, the user should contact their Orica representative or Orica Limited at the contact details on page 1.Orica Limited's responsibility for the material as sold is subject to the terms and conditions of sale, a copy of which is available upon request.Product Name: POTASSIUM AMYL XANTHATE Issued: 03/07/2009 Substance No: 000033326701Version: 4Page 6 of 6。
瓦尔特兵卒1控制阀使用指南说明书
Valtek Trooper1Valtek Trooper2The Valtek ® Trooper valve is a high-performance,general-service control valve with a high-thrust dia-phragm actuator. The valve is designed for use in ANSI Class 150 or 300 service applications with temperatures ranging from -20° to 650° F / -30° to 345° C.In addition to its high thrust, the reversible actuator is compact. An optional integral I/P or P/P positioner ensures high positioning accuracy proportional to the valve instrument signal. The integrally mounted posi-tioner eliminates external tubing requirements, reduces pinch points and keeps moving parts safe from external dirt and damage. Reversing the actuator does not require positioner, tubing changes or extras parts.The actuator accepts air supply pressures up to 60 psig / 4 Barg allowing the valve to shutoff against high-pressure drops. Different spring-sets are available to meet individual application requirements. Removing the reversible actuator from the valve is easy with the unique yoke design and yoke clamps.Many of the standard Mark One valve features are included in the Trooper general service valve including heavy duty, stem guides; self-centering, clamped-in seat ring; raised face integral flanges, multiple trim reductions and easy top-entry valve accessibility.The Trooper valve is available in 1, 11/2, 2, 3 and 4-inch valve sizes and with carbon steel or stainless steel bodies. Valve sizes 1 through 2-inch are also available in socketweld or NPT end connections.The Trooper control valve is the solution for most general-service applications.TMGeneral Service Control ValvesValtek TrooperFeatures & Advantages3Valtek Trooper Options / Flow Capacity4Valtek TrooperTechnical DataTable III: Actuator Data3 lbs / 1.4 kg for I/P positioner.5Valtek Trooper* Per ANSI/ISA S75.03, 1985; ANSI/ISA S75.12, 1987. Socketweld and NPT end connections are available on 1 through 2-inch valves with equivalent face-to-face dimensions.** With top-mounted handwheel add 3.6 in. / 91 mm to actuators sizes 48, 38, 38 I/P; add 4.9in. / 124 mm to actuator sizes 49, 39, 39 I/P.All trademarks and tradenames shown in this literature are the property of their respective owners.DimensionsTable VI: Dimensions (inches /mm )Flowserve Corporation has established industry leadership in the design and manufacture of its products. When properly selected, this Flowserve product is designed to perform its intended function safely during its useful life. However, the purchaser or user of Flowserve products should be aware that Flowserve products might be used in numerous applications under a wide variety of industrial service conditions. Although Flowserve can (and often does) provide general guidelines, it cannot provide specific data and warnings for all possible applications. The purchaser/user must therefore assume the ultimate responsibility for the proper sizing and selection, installation, operation and maintenance of Flowserve products.The purchaser/user should read and understand the Installation Operation Maintenance (IOM) instructions included with the product, and train its employees and contractors in the safe use of Flowserve products in connection with the specific application.While the information and specifications presented in this literature are believed to be accurate, they are supplied for informative purposes only and should not be considered certified or as a guarantee of satisfactory results by reliance thereon. Nothing contained herein is to be construed as a warranty or guarantee, express or implied, regarding any matter with respect to this product. Because Flowserve is continually improving and upgrading its product design, the specifications, dimensions and information contained herein are subject to change without notice. Should any question arise concerning these provisions, the purchaser/user should contact Flowserve Corporation at any of its worldwide operations or offices.。
ASSA ABLOY 安全门系统产品说明书
HIGH SAFETYSafety contact edge or touchless safety edge. Safety limit switches according to PLe and SIL3.HIGH RELIABILITYHigh reliability and low service even after years of high numbers of cycles.HIGH SPEEDRapid opening and closing ensuresshort cycle time.ASSA ABLOY, Besam, Crawford, Albany and Megadoor, as words and logos, are examples of trademarks owned by ASSA ABLOY Entrance Systems or companies within the ASSA ABLOY Group.Machine Protection Door Albany RP300 / RP300 Wide / RP300 USD■R apid opening and closing ensures short cycle times up to 5 cycles per minute■H igh reliability even after years of high numbers of cycles■S afety limit switches according to EN ISO 13849-1 and EN 62061■D oors conform to EN ISO 12100 and EN ISO 14119■V ersions conforming to various factory standards are possible■T ype tested machine protection door with fabric door bladeAdvantages of the doorDesign SIDE FRAMESThe side frames are made of aluminum profiles.The front cover side frame can easily be removedand allows easy access for inspection and mainte-nance.DOOR CURTAINDepending on the application, various doorcurtains and colors are available (see details in thetable). From partially transparent PVC curtains withcolored reinforcement stripes with a high degreeof transparency to highly rigid RollTex® and No-maTex®. All door curtains are silicon-free.Side-mounted wind tabs reduce inward bending ofthe door blade. RollTex® according to TRAV (techni-cal rules for use of anti-fall guard vitrification).WINDOWSFor process monitoring when the door is closed,various window variants are available. On PVCcurtains with colored reinforcement strips, thereare large viewing areas. For all other variants ofcurtains, optional horizontal or vertical windowsare integrated in the door curtain. Also anti-UVwindows conform to EN 1598.DRIVE UNITGear motor with safety gear box including catchingdevice, mounted on the right or left side.CONTROL SYSTEMDepending on the application there are 2 controlsystems which offer a broad spectrum of speeds,power supplies and options for connecting controland safety devices.Standard: ACS 50Option: frequency converter control MCCUpon request the door can also be deliveredwithout a control system (not Upside Down).Extension box: Space saving extension box forMCC allows mounting of interface card or safetymonitoring module for safety limit switches.SAFTEY LIMIT SWITCH INTEGRATEDIN SIDE FRAMEFor the indication “door safely closed”, safety limit switches are integrated in the side frame. Optional evaluation by safety systems of the machi-ne (version without safety monitoring module). Due to the use of safety limit switches, m achine protection doors cannot be e quipped with a knock-out mechanism.MOTOR COVER AND TOP ROLL COVERMotor cover is made of powder coated steel plate (RAL 9006). Top roll cover is made of aluminium.MODEL ALBANY RP300 USDThe new Albany RP300 USD (Upside Down) ma-chine protection door is designed so that you can integrate it into your production area where bigger components and machinery must be arranged vertically.INTEGRATED CABLE CHAINIntegrated cable chain guides cables for pre-running photocell or electrical safety contact edge inside the side frame.MANUAL ACTIVATIONDuring a power failure the door can be opened manually using a hand crank.SAFETY FEATURESThe bottom profile is monitored by an electrical safety contact edge. As an option, the door can be equipped with a pre-running photocell in combi-nation with the control system MCC (Standard on Upside Down). A door line photocell also prevents the door from closing when objects are interfering. CE GUIDELINESThis door is designed according to the regulations of the Workplace Directive of the UVV as well as the harmonized CE Guidelines including the EN 13241-1 and 2006/42/EG.INDICATION OF RISKThe security of the door is designed for normal use for vehicles in industrial environments correspon-ding to the harmonized CE-Guidelines. In addition, special environmental conditions may impact the type of door necessary. For clarification and details, please contact your local sales engineer.Floor mounting brackets The door can be mounted free-standing on floor with optional mounting brackets. Levelling screws allow adjustment byuneven floor.Motor position Motor can be mounted right- or lefthand side. Motor position can be chosen in step of 45°. A chain drive is available as option in case of space limitations.Saftey limit switch Optional: For the indication “door safely closed”, safety limit switches are integrated in the side frame. Technical Data Albany RP300 / RP300 Wide / RP300 USD• Option ✓ Standard *) Specific number of cycles on request1) F or doors of height < 2300 mm the use of top roll cover is required according to standard EN 13241-1.2) Deviations possible depending on other properties3) Depending on cycles/minute, door size and installation locationThe Albany RP300 USD closes from bottom to topThe demands in automated manufacturing processes are high and the smallest interruption or delay can break down the flow of production or endanger employees. Machine protection doors help manufacturers avoid both scenarios. The doors are integrated into the processes and open and close according the production run. They enable the rapid change from complete isolation of the production step to free access to work piece and machine within seconds. It allows short cycle times and can be installed in machines, on production lines and railing systems wi-thin close proximity to the machine. Plus, they protect people in highly automated areas, making processes much safer.Advantages of the Albany RP300/RP300 Wide/RP300 USD■ S ervice friendly: Two-pieced aluminum side frames offer easy accessfor inspection and maintenance■ P re-running photocell: in combination with control system AlbanyMCC a pre-running photocell is available as option. It provides more comfort and higher closing speed■I ntegrated cable chain: The cables of the electrical safety contact edge and pre-running photocell are guided in cable chains inside the side frame■P luggable cables in the cable chain ■D rive unit: A chain drive is available as option in case of space limita-tionsConnection with the machine The in- and outputs of the door control unit MCC (potential 24 V DC) can be connected directly, to the machine. The in- and outputs of the door control unit MCC and ACS 50 can be connected potentialfree with the machine. As standard the following signals are available:■2 potential-free safety contacts, when the door is closed (safety limit switch)■ 1 output or potential-free signal, when the door is open■ 1 output or potential-free signal when the door is closed■ 1 output or potential-free signal for faults Example of use: door in assembly lineExample of use: place a workpiece into the processGeneral drawing Albany RP300[ ] = S pace needed for installationwithout coverwith MCC / side frame with window9300R0009/a9300R0022/0[ ] = S pace needed for installationFollow us:Please enter ASSA ABLOY Entrance in the channel’s search field.For subsidiary or representatives in your region visit:AAES productionAAES Reseller© A S S A A B L O Y E n t r a n c e S y s t e m s A B B R .M A N /A l b a n y R P 300 W i d e / D E U .E N -1.1/1608 / 64 100 728 T e c h n i c a l d a t a s u b j e c t t o c h a n g e w i t h o u t n o t i c e ASSA ABLOY Entrance Systems ***********************。
Flexo 洗浴椅说明书
Instructions for useFlexo5100 5199Shower-toilet chairContents1 . Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 1 .1 . Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 1 .2 . Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .191 .3 . Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .212 . Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 2 .1 . First use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .212 .2 . Working with the Flexo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .223 . Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 3 .1 . Wheel blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 3 .2 . Footrest . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 3 .3 . Armrest with front closure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 3 .4 . Moving upwards / downwards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 3 .5 . Toilet function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 3 .5 .1 . In combination with toilet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .253 .5 .2 . Use of a bedpan or bucket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .264 . Cleaning and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .265 . Storage and transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .276 . Removal of parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .287 . Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 7 .1 . Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 7 .2 . Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 7 .3 . Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2818 | Instructions for use | Flexo Shower-toilet chair20 | Instructions for use | Flexo Shower-toilet chair•Set the Flexo to the correct height before using with a toilet .•The Flexo may not be used to lift persons weighing over 135 kg .•The Flexo may not be used to transport loads other than people .•Only use original parts, supplied by Lopital .•Use the Flexo in a clean and tidy working environment .•The Flexo may only be operated by an authorised person .• Swimming pool locations are not considered to be ‘normal conditions’ and will substantially shorten the lifespan of certain components .• During use of the Flexo, the water temperature may not exceed 43°C .Seat fillerBedpan guidesHinge coverPump pedalSwivel wheel Ø12,5 cm Dual braking HandleBack supportArmrest(front closure)Bumper Seat footrest complete Frame Scissor mechanism22 | Instructions for use | Flexo Shower-toilet chair2.2. Working with the FlexoStep 1Fold the armrests up or turn the front closure downwards(See paragraph 3.3 Armrest with front closure) .Step 2If necessary, fold the foot plates up or turn the footrests away(See paragraph 3.2 Footrests) .Step 3The Flexo must be put on the brakes before transferring persons(See paragraph 3.1. Wheel blocking) .Step 4The client can take a seat in the chair . Support the client if necessaryStep 5Place both feet on the footrests and calves against the calf-supports(See paragraph 3.2 Footrests) .Step 6Close the armrests once the client has taken a seat in the chair(See paragraph 3.3 Armrest with front closure) .Step 7Notify the client about the processes you will be carrying out .Step 8Take the chair off the brake when you wish to move it(See paragraph 3.1. Wheel blocking). Always move the chair in the low position. Step 9When you wish to move the chair upwards / downwards, you must apply the brake (See paragraph 3.4. Moving upwards / downwards).2124 | Instructions for use | Flexo Shower-toilet chair3.3. Armrest with front closure• If the client has taken a seat on the Flexo, the armrests with front closure can be folded down; these are then turned for the person concerned .• The armrests with front closure are secured in a horizontal position .• The armrests can be unlocked by pressing the security catch at the hinging point on the frame (See figure 5). The armrest can then be turned up for the client and folded up .• Always protect the client when folding the armrests up or down .• The armrests can also be used as a support when taking a seat or standing up . Be aware that the armrests are not locked in all positions .Option: Armrest with dual locking (Article number: 68405661).• The extra lock ensures that the front closure is also locked when turned away (See figure 7) .When folding the armrest away, avoid the hinging point so as to avoid becoming jammed.When folding the armrests away, avoid fingers or body parts becoming jammed between the armrest and the back support.The armrest or front closure must not be used as a lever arm (e.g. when moving the chair over an obstacle) or as a push / pull bar. You must not sit on it either.This could damage the Flexo and / or present a hazard.Figure 7 Armrest turned out .Figure 6Armrest with dual locking .Figure 5 Armrest .The Flexo does not fit over every toilet.3.5.2. Use of a bedpan or bucket• If the Flexo is being used as a toilet chair, the specialguides under the seat can be used to accommodate astainless steel / plastic bedpan or bucket .• Slide the bedpan or bucket in from the back of the chair(See figure 10) .In order to avoid injuries, we advise the carer toremove the lid from the seat and insert the bucket orbedpan before the client takes a seat on the chair.4. Cleaning and maintenanceThe Flexo must be cleaned after every use, with water and regular household cleaning agents . Remove excess soap residues . PUR integrated foam components with IMC coating should be rubbed clean and disinfected . Do not use any abrasive or other aggressive cleaning products (e .g . chlorine bleach) . Practical experience has shown that regular household cleaning agents with limited alcohol content (max . 5%) are most suitable for this purpose . The product Neoquat combi ® is recommended for disinfection purposes (on the basis of long-term testing) . If necessary, the PUR components can be cleaned with a solution of 70% ethanol or propanol .You must ensure that both the disinfecting and cleaning processes involve the compo-nents being rubbed and not just submerged . The time the products must be left on the components has a significant impact upon the lifespan of the PUR components . As a result of the material properties of PUR, contact with sharp objects must be avoided . This could lead to damage or tears in the material . Finally, we would like to point out that non-criti-cal parts of the PUR components must also be cleaned and decontaminated .Check the wheels regularly for hairs, dust and soap residues and remove when necessary . Maintenance and repairs to the Flexo may only be carried out by authorised personnel .Figure 10 Bedpan .6. Removal of partsAll parts that are replaced or removed can be sent back to Lopital BV . You may also offer the parts to the engineer for destruction . We will ensure that all parts are processed in an environmentally-friendly manner .7. Technical SpecificationsThe Flexo Shower-toilet chair belongs to category ‘BF’.6.1. StructureFrame: s tainless steel and steel tubes and plates that are equip-ped with a 2-layer powder coatingHinge points : stainless steel, cover caps made of plastic V0 Wheels: plastic, Ø 12,5 cm, dual blocking facilityBody support : PUR (polyurethane) .Weight: 39 kgMaximum permitted load : 135 Kg6.2. DriveIntegrated hydraulic pump6.3. DimensionsSurface area: 70 cm wide, 87 cm deepSeat height: Adjustable: minimum 50 cm, maximum 105 cmEnglish。