环氧胶粘剂检验原始记录表格
胶粘剂检测原始记录
样品编号：检测依据：检测日期：
检验项目
龄期d
试样尺寸㎜
破坏载荷N
破坏部位
拉伸粘结强度原强度MPa
可操作时间h（静置h后粘结强度原强度MPa）
长
宽
原强度载荷
可操作时间载荷
原强度破坏部位
可操作时间破坏部位
与膨胀聚苯板
1
2
3
4
5
平均值
与水泥砂浆
1
2
3
4
5
平均值
计算公式：
σb—拉伸粘结强度原强度MPa Pb—破坏载荷N A—试样面积㎜2
环境
条件
℃%RH
所用仪器
WDW3010电子万能试验机
试验前
□正常□异常
试验后
□正常□异常
备注
记录：检验：校核：
胶粘剂粘结强度耐水强度检测原始记录制作日期：
样品编号：检测依据：检测日期：
检验项目
龄期d
试样尺寸㎜
破坏载荷N
破坏部位
拉伸粘结强度耐水强度MPa
长
宽
与膨胀聚苯板
1
2
3
4
5பைடு நூலகம்
平均值
与水泥砂浆
1
2
3
4
5
平均值
计算公式：
σb—拉伸粘结强度耐水强度MPa Pb—破坏载荷N A—试样面积㎜2
环境
条件
℃%RH
所用仪器
WDW3010电子万能试验机
试验前
□正常□异常
试验后
□正常□异常
备注
记录：检验：校核：
3M Scotch-Weld DP460白色和DP460NS环氧胶粘剂技术数据表格 说明书
Scotch-W eld™Epoxy Adhesives DP460 Off-White andDP460NSTechnical Data Sheet January 2019Product Description 3M™ Scotch-Weld™ Epoxy Adhesives DP460 Off-White and DP460NSare high performance, two-part epoxy adhesives offering outstandingshear and peel adhesion, and very high levels of durability.Features • High shear strength • High peel strength• 60 minute work life • Non sag (DP460NS)• Easy mixingTypical Uncured Physical Properties Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes.Product3M™ Scotch-Weld™Epoxy AdhesiveDP460 Off-White3M™ Scotch-Weld™Epoxy AdhesiveDP460NSViscosity (approx.)@ 73°F (23°C)BaseAccelerator20,000-50,000 cps8,000-14,000 cps150,000-275,000 cps8,000-14,000 cps Base Resin BaseAcceleratorepoxyamineepoxyamineColor BaseAcceleratorwhiteamberwhiteamberNet Weight Base 9.3-9.7 9.3-9.7 Lbs./Gallon Accelerator 8.8-9.2 8.8-9.2Mix Ratio (B:A) Volume 2:1 2:1Weight 2:0.96 2:0.96 Work life, 73°F (23°C) 20 g mixed10 g mixed5 g mixed60 minutes75 minutes90 minutes60 minutes60 minutes60 minutes13M ™ Scotch-Weld ™ Epoxy Adhesives DP460 Off-White • DP460NS2Typical Cured Thermal PropertiesNote: The following technical information and data should be consideredrepresentative or typical only and should not be used for specification purposes.Typical Curing CharacteristicsNote: The following technical information and data should be consideredrepresentative or typical only and should not be used for specification purposes. Rate of Strength Build-UpAluminum, Overlap Shear (7 mil Bondline) (ASTM D 1002-72) Bonds Tested at 73°F (23°C)3M ™Scotch-Weld ™ Epoxy Adhesive DP460 Off-White3M ™Scotch-Weld ™ Epoxy Adhesive DP460NSThis represents the oven temperature to which the bonds were subjected for the prescribed time. The average bondline temperature during the cure time will be somewhat lower than the oven temperature.The value in the denominator is the expected minimum 73°F (23°C) T -peel strength (piw) measured after the indicated cure cycle.NOTE: The data in this T echnical Data Sheet were generated using the 3M ™ EPX Applicator System equipped with an EPX static mixer,according to manufacturer ’s directions. Thorough hand-mixing will afford comparable results.3M ™ Scotch-Weld ™ Epoxy Adhesives DP460 Off-White • DP460NS3Typical Adhesive Performance CharacteristicsNote: The following technical information and data should be consideredrepresentative or typical only and should not be used for specification purposes.Substrates and TestingA. Overlap Shear (ASTM D 1002-72)Overlap shear (OLS) strengths were measured on 1 in. wide 1/2 in. overlap specimens. These bonds were made individually using 1 in. x 4 in. pieces of substrate except for aluminum. Two panels 0.063 in. thick, 4 in. x 7 in. of 2024T-3 clad aluminum were bonded and cut into 1 in. wide samples after 24 hours. The thickness of the bondline was 0.005-0.008 in. All strengths were measured at 73°F (23°C) except where noted.The separation rate of the testing jaws was 0.1 in. per minute for metals, 2 in. per minute for plastics and 20 in. per minute for rubbers. The thickness of the substrates were: steel, 0.060 in.; other metals, 0.05-0.064 in.; rubbers, 0.125 in.; plastics, 0.125 in.B. T-peel (ASTM D 1876-61T)T-peel strengths were measured on 1 in. wide bonds at 73°F (23°C). The testing jaw separation rate was 20 inches per minute. The substrates were 0.032 in. thick.C. Bell Peel (ASTM D 3167)Bell peel strengths were measured on 1/2 in. wide bonds at the temperatures noted. Thetesting jaw separation rate was 6 in. per minute. The bonds are made with 0.064 in. bonded to 0.025 in. thick adherends.D. Cure CycleWith the exception of Rate of Strength Build-Up Tests, all bonds, were cured 7 days at 73°F (23°C) at 50% RH before testing or subjected to further conditioning or environmental aging.Aluminum, Overlap Shear, at Temperature (PSI)1Represents time in test chamber oven before test.Metals, Overlap Shear, Tested @ 73°F (23°C) (PSI)3M ™ Scotch-Weld ™ Epoxy Adhesives DP460 Off-White • DP460NS4Typical Adhesive Performance Characteristics(continued)Note: The following technical information and data should be consideredrepresentative or typical only and should not be used for specification purposes.Substrates and TestingAluminum, T -Peel (PIW), at Temperature Aluminum, etched (17-20 mil bondline)Aluminum Bell Peel (PIW), at Temperature (ASTM D 3167)Other Substrates, Overlap Shear Tested @ 73°F (23°C)2Isopropyl Alcohol/Abrade/Isopropyl Alcohol: See Surface Preparation Section E for additional information. 3Substrate failure3M ™ Scotch-Weld ™ Epoxy Adhesives DP460 Off-White • DP460NS5Typical Adhesive Performance Characteristics(continued)Note: The following technical information and data should be consideredrepresentative or typical only and should not be used for specification purposes.Substrates and Testing (continued)Environmental Resistance, Aluminum (Etched)Measured by Overlap Shear Tested @ 73°F (23°C) (PSI)1(ASTM D 1002-72)1Data reported are actual values from the lots tested and may be higher than values published elsewhere in this T echnical Data Sheet. 2 d = days 3 i = immersionEnvironmental Resistance, Galvanized Steels 1Measured by Overlap Shear Tested @ 73°F (23°C) (PSI)2(ASTM D 1002-72)1Hot dipped or electrodeposited. Galvanized steels may afford a wide spectrum of performance due to the diversity of surfaces available. The user should test to determine specific performance.2Data reported are actual values from the lots tested and may be higher than values published elsewhere in this T echnical Data Sheet. 3d = days4i = immersion3M ™ Scotch-Weld ™ Epoxy Adhesives DP460 Off-White • DP460NS63M ™ EPX Pneumatic Applicator Delivery Rates200 ml Applicator – Maximum Pressure 58 psi*T ests were run at a temperature of 70°F ± 2°F (21°C ± 1°C) and at maximum applicator pressure.Handling/ Application InformationDirections for Use3M ™ Scotch-Weld ™ Epoxy Adhesives DP460 Off-White and DP460 NS are supplied in dual syringe plastic duo-pak cartridges as part of the 3M ™ EPXApplicator System. The duo-pak cartridges are supplied in 37 ml, 200 ml and 400 ml configurations. To use the 37 ml cartridge simply insert the duo-pak cartridge into the EPX applicator and start the plunger into the cylinders using light pressure on the trigger. Next, remove the duo-pak cartridge cap and expel a small amount of adhesive to be sure both sides of the duo-pak cartridge are flowing evenly and freely. If simultaneous mixing of Part A and Part B is desired, attach the EPX mixing nozzle to the duo-pak cartridge and begin dispensing the adhesive.With the 200 ml and 400 ml cartridges, the nozzle must be attached before dispensing any material to prevent unmixed adhesive from getting into theapplicator cartridge holder. A small quantity of material should be discarded until uniform color, consistency of product and even flow is evident.When mixing Part A and Part B manually, the components must be mixed in the ratio indicated in the typical uncured properties section. Complete mixing of the two components is required to obtain optimum properties.Two-part mixing/proportioning/dispensing equipment is available for intermittent or production line use. These systems are ideal for line uses because of their variable shot size and flow rate characteristics and are adaptable to most applications.3M™ Scotch-Weld™ Epoxy AdhesivesDP460 Off-White • DP460NSSurface Preparation The following surface preparations were used for substrates described in thisTechnical Data Sheet.A.Aluminum EtchOptimized FPL Etch - 3M (test method C-2803)1.Alkaline degrease – Oakite 164 solution (9-11 oz./gallon water) at 190°F ±10°F (88°C ± 5°C) for 10-20 minutes. Rinse immediately in large quantitiesof cold running water (3M test method C-2802).2.Optimized FPL Etch Solution (1 liter):Material AmountDistilled Water 700 ml plus balance of liter (see below)Sodium Dichromate 28 to 67.3 gramsSulfuric Acid 287.9 to 310.0 gramsAluminum Chips 1.5 grams/liter of mixed solutionTo prepare 1 liter of this solution, dissolve sodium dichromate in 700 ml ofdistilled water. Add sulfuric acid and mix well. Add additional distilled waterto fill to 1 liter. Heat mixed solution to 66 to 71°C (150 to 160°F). Dissolve1.5 grams of 2024 bare aluminum chips per liter of mixed solution. Gentleagitation will help aluminum dissolve in about 24 hours.To FPL etch panels, place them in the above solution at 150 to 160°F (66 to71°C) for 12 to 15 minutes.Note: Review and follow precautionary information provided bychemical suppliers prior to preparation of this etch solution.3.Rinse immediately in large quantities of clear running tap water.4.Dry – air dry approximately 15 minutes followed by force dry at 140°F(60°C) maximum for 10 minutes (minimum).5.Both surface structure and chemistry play a significant role in determiningthe strength and permanence of bonded structures. It is therefore advisableto bond or prime freshly primed clean surfaces as soon as possible aftersurface preparation in order to avoid contamination and/or mechanicaldamage. Please contact your 3M sales representative for primerrecommendations.B.Oakite DegreaseOakite 164 solutions (9-11 oz./gallon of water) at 190°F ± 10°F (88°C ± 5°C) for 2minutes. Rinse immediately in large quantities of cold running water.C.MEK/Abrade/MEKWipe surface with a methyl ethyl ketone (MEK) soaked swab, abrade and wipewith a MEK soaked swab.* Allow solvent to evaporate before applying adhesive.D.Isopropyl Alcohol WipeWipe surface with an isopropyl alcohol soaked swab.* Allow solvent to evaporatebefore applying adhesive.E.Isopropyl Alcohol/Abrade/Isopropyl AlcoholWipe surface with an isopropyl alcohol soaked swab, abrade using clean fine gritabrasives, and wipe with an isopropyl alcohol soaked swab.* Then allow solventto evaporate before applying adhesive.*Note: When using solvents, extinguish all ignition sources, including pilot lights,and follow the manufacturer’s precautions and directions for use.73M ™ Scotch-Weld ™ Epoxy Adhesives DP460 Off-White • DP460NS8StorageStore products at 60-80°F (15-27°C) for maximum shelf life.Shelf LifeThese products have a shelf life of 24 months from date of manufacture in original containers at room temperatureTechnical InformationThe technical information, guidance, and other statements contained in this document or otherwise provided by 3M are based upon records, tests, or experience that 3M believes to be reliable, but theaccuracy, completeness, and representative nature of such information is not guaranteed. Such information is intended for people with knowledge and technical skills sufficient to assess and apply their own informed judgment to the information. No license under any 3M or third party intellectual property rights is granted or implied with this information.Product Selection and UseMany factors beyond 3M’s control and uniquely within user’s knowledge and control can affect the use and performance of a 3M product in a particular application. As a result, customer is solely responsible for evaluating the product and determining whethe r it is appropriate and suitable for customer’sapplication, including conducting a workplace hazard assessment and reviewing all applicable regulations and standards (e.g., OSHA, ANSI, etc.). Failure to properly evaluate, select, and use a 3M product and appropriate safety products, or to meet all applicable safety regulations, may result in injury, sickness, death, and/or harm to property.Warranty,Limited Remedy, and DisclaimerUnless a different warranty is specifically stated on the applicable 3M product packaging or product literature (in which case such warranty governs), 3M warrants that each 3M product meets the applicable 3M product specification at the time 3M ships the product. 3M MAKES NO OTHERWARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY, FITNESS FOR A PARTICULARPURPOSE, OR ARISING OUT OF A COURSE OF DEALING, CUSTOM, OR USAGE OF TRADE. If a 3M product does not conform to this warranty, then the sole and exclusive remedy is, at 3M’s option, replacement of the 3M product or refund of the purchase price.Limitation of LiabilityExcept for the limited remedy stated above, and except to the extent prohibited by law, 3M will not be liable for any loss or damage arising from or related to the 3M product, whether direct, indirect, special, incidental, or consequential (including, but not limited to, lost profits or business opportunity),regardless of the legal or equitable theory asserted, including, but not limited to, warranty, contract, negligence, or strict liability.This Industrial Adhesives and T apes Division product was manufactured under a 3M quality system registered to ISO 9001 standards.Industrial Adhesives and Tapes Division3M Center, Building 225-3S-06St. Paul, MN 55144-100800-362-3550 977-369-2923 ( Fax) /structuraladhesives3M and Scotch-Weld are trademarks of 3M Company.©3M 2017 (9/17)。
保温系统用胶粘剂检验检测原始记录3
实测值
试验：
结论 结论 结论
第 2 页/共 3 页
第 3 页/共 3 页
保温系统用胶粘剂检验检测原始记录
试验编号： 检测项目
可操作时间(h)
拉伸粘接强度 （与水泥砂浆）
技术指标
技术指标
原 强 度
耐 技术指标 水 强 度 ︵ 干 燥 2h ︶ 耐 技术指标 水 强 度
序号 试样面积（mm2）
1
2
3
4
5
序号
长度mm
1
2
3
4
5
6
序号
长度mm
1
2
3
4
5
6
序号
长度mm
1
2
检测情况
1
原
2
强
3
度
4
5
6
耐 技术指标 序号 长度mm 宽度mm
水
1
强 度
2
︵
3
干 燥
4
2h
5
︶
6
耐 技术指标 序号 长度mm 宽度mm
水
1
强 度
2
︵
3
干 燥
4
7d
5
︶
6
破坏荷载(N) 破坏荷载(N) 破坏荷载(N)
审核：
试验复核：
破坏部位
粘结强度(MPa)
实测值
破坏部位
粘结强度(MPa)
实测值
破坏部位
粘结强度(MPa)
破坏荷载（N）
破坏部位
宽度mm
破坏荷载(N)
宽度mm
破坏荷载(N)
宽度mm
破坏荷载(N)
试 验 粘结强度(MPa)
环氧树脂防水涂料试验记录(模板)
样品编号
试验编号
送检日期
类别型号
材料配比
试验日期
厂家牌号
试验环境
℃％RH
检验标准
仪器设备
粘结强度
试件类型
试件编号
试件粘接面尺寸/mm
试件最大拉力/N
破坏形式
拉伸粘结强度/MPa
单个值
平均值
干基面试件
潮湿基面试件
浸水处理试件
热处理试件
备注
校核：试验：
柔韧性
弯曲圆棒直径/mm弯曲角来自/°试验结果抗冲击性
落锤质量/g
下落高度/mm
第1次冲击结果
第2次冲击结果
第3次冲击结果
耐酸性
酸液
浸泡时间
试验结果
起始
结束
试件1
试件2
试件3
耐碱性
碱液
浸泡时间
试验结果
起始
结束
试件1
试件2
试件3
耐盐性
盐溶液
浸泡时间
试验结果
起始
结束
试件1
试件2
试件3
备注
校核：试验：
环氧树脂防水涂料试验记录
环氧树脂防水涂料试验记录
管理编号：XXXXXXXXXXXXX共页第页
样品编号
试验编号
送检日期
类别型号
材料配比
试验日期
厂家牌号
试验环境
℃％RH
检验标准
仪器设备
外观
□搅拌后，产品各组分为均匀的液体，无凝胶、结块。
□
干燥时间
试验序号
表干时间
实干时间
涂膜时间
表干时间
评定值/h
环氧沥青防腐漆原始记录
YHZ 样品名称
样品编号
生产厂家
规格/型号
结构部位
代表数量
仪器设备
检测标准
标 准 要 求
(普通型)在容器的中状态搅拌混合后，
无硬块，呈均匀状态
混合性
能均匀混合施工性
刷涂无障碍干燥时间/h
≤24涂膜外观
涂膜外观正常低温稳定性
3次试验后，无结块、凝聚及组成物的变化耐弯曲性/mm
≤10耐冲击性/cm
≥30不挥发物含量
/%
≥60耐碱性
（5%NaOH溶液）
168h 漆膜无异常耐酸性
（5%H 2SO 4溶液）
168h 漆膜无异常结 论
备 注
委托单编号：
环氧沥青防腐漆检测原始记录
审核 ：主检：
平均值 □低温箱DW-40 NYT-SB-HJ-0017 □电子计量称 ACS-15A □电热鼓风干燥箱 DHG-9101-IS 型□ SY/T0447-96《埋地钢质管道环氧煤沥青防腐层技术标准》检验项目试 验 情 况单项评定
检测日期送样数量委托日期生产日期委托人/证号见证人/证号 银川衡正信诚建筑材料检测有限公司。
结构胶黏剂原始记录1
1#
2#
3#
4#
5#
平均值
标准差
离散系数
（%）
试件厚度（mm）
厚度平均值（mm）
试件宽度（mm）
宽度平均值（nun）
最大荷载（N）
拉伸强度（MPa）
断裂时的标距（mm）
伸长率（%）
弹性模量（MPa）
二.抗压强度检测：（配比：：二：；试样尺寸①10mmX25mm；浇注日期：月 日；
h后脱模；再在标准环境C下放置504h；加工后再放置24h；检测日期： 月 日；加载
试件编号
1
2
3
4
5
试样厚度（nιm）
厚度平均值（mm）
跨距二16X厚度（mm）
最大荷载（N）
抗弯强度（MPa）
平均值（MPa）
标准差
离散系数（％）
检验结论：
复核:
检测:
结构胶黏剂材料性能试验原始记录纸
第页共页
样品编号
品种规格
数 量
样品状况
试验环境
℃%RH
检测日期
月 日~月 日
检测项目
评定依据
检测方法
检测设备
试验内容来自一.拉伸强度检测：（配比：：二:;哑铃型试样浇注日期：月 日；h后脱模；再在标准环境℃
下放置504h；检测日期：月R；伸长率标距：mm；拉伸速度：min/min；）
速度mm/min；）
试件编号
1
2
3
4
5
试样直径（mm）
直径平均值（mm）
最大荷载（N）
抗压强度（MPa）
平均值（MPa）
标准差
离散系数（Q
三.抗弯强度检测：（配比：：=：;制样日期：月 日；h后脱模；再在标准环境C下放置
保温砂浆、抹面胶浆、胶粘剂检验原始记录
（重量比)
检验依据
□GB/T20473-2006 □GB/T10294-2008 □GB/T5486-2008 □JG158-2013 □GB/T 29906-2013 □JC/T993-2006
□JC/T992-2006 □JGJ/T70-2009 □GB/T17371-2008
主要
仪器设备
□无裂纹
□裂纹处胶粘剂最大厚度 mm
备注
校核人： 试验人：
保温砂浆、抹面胶浆、胶粘剂检验原始记录
管理编号：XXXX共 页第 页
样品编号
样品名称
委托日期
成型环境
试验编号
工程部位
成型日期
℃ RH%
样品状态
□正常 □异常
类型
□Ⅰ □Ⅱ □F □Y □
材料比例
（重量比)
检验依据
□GB/T20473-2006 □GB/T5486-2008 □JG158-2013 □GB/T 29906-2013 □JC/T993-2006
说明
校核人： 试验人：
1
□有水渗透 □无水渗透
□合格 □不合格
2
□有水渗透 □无水渗透
□合格 □不合格
说明
件养护时间□56d□28d
抗冲击性试件尺寸（长×宽）mm□试验日期：
试件
钢球质量（kg)
钢球直径mm
冲击高度m
冲击的次数
破坏的次数
抗冲击强度J
1
□0.5kg □535g
□1.0kg □1.045g
□50.8
□63.5
料浆质量㎏
湿表观密kg/m3
检验项目
试验日期
试 验 项 目
干密度
涂料、胶粘剂、处理剂、腻子、壁纸有害物质检测原始记录(一)(2020.12.01启用)
化合物质量mci（mg）
/
峰面积Ais
/
/
相对校正因子Ri
/
/
/
/
Ri样量mi（g）
内标物质量mis（mg）
/
峰面积Ai
含量（mg/g）
/
苯、甲苯、乙苯和二甲苯总和（mg/kg）
VOC含量（ ）
备注
校核：试验：
XXXXXX有限公司
涂料、胶粘剂、处理剂、腻子、壁纸有害物质检测记录（一）
管理编号：XXXXXX共页第页
样品名称
环境条件
委托日期
样品编号
试验编号
检验日期
仪器设备
检测标准
□GB18582-2020□GB18583-2008□JC 1066-2008□GB/T 23993-2009□GB/T 6750-2007
1
/
/
2
试样
1
/
/
2
2.密度测定ρ水温℃：水的密度g/mL：
项目
容积标定
样品密度
编号
1
2
1
2
比重瓶质量（g）
比重瓶＋样品（水）质量（g）
容积（mL）
/
/
密度（g/mL）
/
/
密度平均值（g/mL）
/
3.苯、甲苯、乙苯和二甲苯总和、挥发物（VOC）的测定
样品项目
苯
甲苯
乙苯
对间二甲苯
邻二甲苯
异丁醇
未识别峰
□
一．甲醛
标准曲线编号
Bs
编号
称样量(g)
吸光度（A）
游离甲醛含量（mg/kg）
平均值（mg/kg）
空白
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
《陶瓷墙地砖胶粘剂》JC/T547
计Байду номын сангаас公式
平均值 Af=F/S
1.压剪强度试件胶接面积 S 为 50mm×20mm.
2.标准试验条件：温度（23±2）℃，相对湿度（50±5）%，试验速率为 5mm/min.
3.标准条件：试样在标准条件下固化 48h 后进行测试；浸水试验在标准条件下固化 48h，接着在（23±2）℃水中浸泡 168h，在 10min 内擦干试件表面 水渍并进行测试；热处理试验在标准条件下固化 48h，接着在（80±2）℃烘箱中放置 168h，在标准条件下冷却 2h 后进行测试.
强度 Af(MPa)
规格类型
委托日期
压剪强度（石材—石材）
浸水（23±2℃、168h）
荷载 F(N)
强度 Af (MPa)
样品编号 检验日期
热处理（80±2℃、168h）
荷载 F(N)
强度 Af (MPa)
平均值
平均值
平均值
微机控制电子万能试验机、电热鼓风恒温干燥箱
《干挂石材幕墙用环氧胶粘剂》JC887
样品名称 样品状态
检验项目 编号 1 2 3 4 5
仪器设备 检验依据
说明
环氧胶粘剂检验原始记录表格
试验环境
固化条件
压剪强度（石材—不锈钢）
标准条件（48h）
荷载 F (N)
强度 Af (MPa)
温度： 相对湿度：
__月__日__时__分至__月__日 时 分放置 h.
标准条件（48h）
荷载 F(N)
检验结论
备注 检验：
复核：
第页
共页