BCD260EI伊莱克斯维修手册
#Electrolux 自 由 空 间 系 列 冰 箱 ＢＣＤ－２６０ＥＩ
稳定运行模式三个循环优先级别为：酒室循环第一，冷藏室循环第二，冷冻室循环 第三。
?? 注：由于酒室和冷藏室的回气管连接在冷冻室蒸发管道的前端，使其作为回气管连接到压缩 机。所以在关闭冷冻室制冷的状态下，仍会有一定的冷量，该冷量不可控制。
导线的断开与接通。 ３）显示电路板：显示板采用 LCD 屏幕，除温度、时间可调节外还加入了六项食品管理 器，操作时有蓝色背景光、外型美观大方、控制方便。（操作方法详见说明书）
４）控制线路板：具有断电时间记忆与延时功能，在冰箱开机不作任何设置的情况下， 其默认温度以及可调节范围为：
存温度、天数。 ５： ＬＣＤ 液晶显示屏。 ６： 瓜果蔬菜图标。 ７： 冷藏、冷冻、酒室开关键／食品管理中食品取消键。 ８： 猪肉类食物图标。 ９： 牛奶饮料图标。 １０：酒室温度。 １１：设定／菜单上调键。 １２：快速冷冻图标，。 １３：快速冷冻键，按下后显示屏上的快速冷冻图标 显现，冰箱压缩机提速运行 ，温度不受限制，可
阀，按额定加注量进行加注，加注完毕后先关闭三通表阀再关闭加注瓶上的阀门，之
后再打开三通表阀让其将加注软管内的 Ｒ６００ａ 吸入制冷系统中。最后关闭三通表阀并
撤离加注软管。
⑧进行试机，经过 １￣２ 开停机次正常后，用封口钳夹住工艺管上部，用洛克钳和洛克环
堵头封口。在开机状态时封压缩机工艺口、在停机状态并且压力均衡时封过滤器工艺
毛细管上有一小段黑色标记的为冷藏室系统。 毛细管上没有颜色标记的为冷冻室系统。
５） 温度传感器：冰箱内有五个传感器，分别分布在酒室内胆、酒室蒸发器、冷藏室内
胆、冷藏室蒸发器以及冷冻室内胆上。其温度电阻值为：
维修场地内应使用一套排风系统全面排风，以保证换气量和排气均匀，防止气体
积聚。
维修场地的通风设备及电器设备使用防爆型。总电源开关应设置在场地之外，并 有防护装置。场地内有数量足够的灭火器，有防火标置。
维修人员每日进入维修场地前，应先检查有无火源，保证无火源后进入维修场地，
打开通风系统后才能进行制冷系统维修工作。
冷藏室 酒室 冷冻室
默认温度 ＋５℃ ＋５℃ －１８℃
可调节范围 ＋２℃ ~ ＋８℃或“Ｈ” ０℃ ~ ＋６℃（无 １℃） －１８℃ ~ －２６℃
注：“Ｈ”代表假日功能，当冷藏室调至＋１０℃上时显示“Ｈ”为假日功能，温度默认为＋１４℃。
５）电磁阀：采用的两个电磁阀，是产自德国 AWECO 公司的产品，为两位三通的脉 冲电磁阀。
3
#Electrolux 自 由 空 间 系 列 冰 箱 ＢＣＤ－２６０ＥＩ
五、部件以及说明
１） 压缩机：压缩机采用的是扎努西 Ｒ６００ａ 制冷剂专用压缩机，其气缸容积比 R12 和 R134a 的压缩机大 65%~70%，且保护器必须是内藏式。
口。封口完毕用肥皂水进行检漏。
1、 带快速接头三通表 6、真空泵 11、R600a 罐子
2、快速接头帽 7、压缩机 12、电子称
3、真空管
4、过滤器工艺管
8、压缩机工艺管 9、加注软管
5、双头过滤器 10、三通阀表
维修注意事项：
１、在不更换压缩机的情况下，加氮气进行清洗时，氮气压力应控制在 ０．４Ｍｐａ 以下，以
ｇ
气候类型
重量：
Ｋｇ
颜色
压缩机型号：
额定电压／频率：
Ｖ／ＨＺ
电压范围
Ｖ
输入功率：
Ｗ
耗电量：
Ｋｗ．ｈ／２４ｈ
冷冻能力：
Ｋｇ／２４ｈ
冷凝器方式：
冷冻室布局：
温度调节范围；冷藏
℃
酒室
℃
冷冻
入下一步操作。
⑥ 用抽空软管联接过滤器端的三通表阀和真空泵，用加注软管（加注软管越短越好）联
接压缩机工艺管端的三通表阀和电子称上的 Ｒ６００ａ 加注瓶，打开真空泵和两块三通表
阀的阀门对系统进行抽空，同时也把加注软管中的残留空气抽掉。此时 Ｒ６００ａ 加注瓶
的阀门应是关闭的。（如下图所示）
⑦达到真空要求时，关闭过滤器端的三通表阀门撤离抽空软管，缓慢打开 Ｒ６００ａ 加注瓶
因此不能随意更换其它制冷剂的压缩机。
２）灯开关： 冷藏室和酒室的门灯开关为磁力感应开关，冷藏室的
磁力感应开关直接卡装在顶盖的前部，拆装方便，而
酒室的感应开关则埋在箱体的门框内，不可更换。它
们靠装在相应门上的磁铁来达到开门灯亮，关门灯灭
的作用。 检测好坏时可用磁铁的靠近与分离，来测量两根
电源电压 230V/50Hz
正脉冲驱动
阀 开关
负脉冲 驱动
电磁阀的工作电压为 175V~264V
环境温度为 20~25℃时其阀体线圈绕阻值为 2795? ± 10% 在维修时应注意：两个电磁阀的肆路管道输出的正确焊接，
毛细管上有一小段红色标记的为酒室系统。
#Electrolux 自 由 空 间 系 列 冰 箱 ＢＣＤ－２６０ＥＩ
一、 主要技术参数
型号：
产品代码：
外形尺寸（宽×深×高）： ｍｍ
有效容积（冷藏／酒室／冷冻）： Ｌ
制冷剂（Ｒ６００ａ）：
防冲坏压缩机阀钢片，造成压缩机噪声增大。
２、保证工艺管口的圆整，防止洛克环堵头封口时封闭不严而产生泄露。
３、Ｒ６００ａ 的灌注量应严格控制在额定量的正负贰克以内。
４、在维修过程中始终保持通风，防止发生泄露后，再临时开启任何电源开关。
6
#Electrolux 自 由 空 间 系 列 冰 箱 ＢＣＤ－２６０ＥＩ 七、故障显示以及处理
④用管割刀割开工艺管口，套上三通阀表，注入小于 ０．４Ｍｐａ 压力的氮气进行清洗，此
时将毛细管口修剪圆整。
２ 分钟后关闭氮气阀，并撤离排空钳、三通阀表，进行焊接和更换压缩机。
⑤更换焊接完毕后，在压缩机工艺管上和双头过滤器端的工艺管分别接上三通阀表。在
压缩机工艺管端缓慢注入 ０．８Ｍｐａ 的氮气对焊接点进行检漏。确认不漏后排掉氮气进
四、控制面板及其说明
１： 锁定图标。按住下调键（２２）５ 秒以上，显示屏上出现锁定图标，所有按键被锁定，反之取消。
２： 快速冷藏键，按下后显示屏显示 图标，冷藏室按＋２℃设置运行，压缩机提速运行，６ 小时 后自动退出快速冷藏。６ 小时内也可手动退出。
３： 快速冷藏图标 ４： 时钟／存放温度及天数。通常情况下为时间显示，在食品管理模式中则分别为推荐食物的最佳储
1
#Electrolux 自 由 空 间 系 列 冰 箱 ＢＣＤ－２６０箱会在商检模式下运行，首先冷冻室下降几度，其次是酒 室下降几度、然后是冷藏室下降几度，然后压缩机停机，商检模式完成转入正常稳定运 行模式。
以降到很低，在 ４８ 小时后自退出，４８ 小时内也可手动退出 。 １４：报警图标。此图标闪烁并伴随报警声，表示冷藏室或酒室门未关好，或者是食品管理器中的食
物设定时间到期。 １５：冷藏室温度。 １６：鸡鸭类食物图标。 １７：菜单切换确认键。 １８：鱼、海鲜类食物图标。 １９：牛、羊类食物图标。 ２０：冷冻室温度。 ２１：设定／菜单下调键。
２、维修工艺 ① 用排空钳刺穿过滤器上部工艺管，将排空钳上的排气管将 Ｒ６００ａ 引至室外排放。
② 用钳子夹断过滤器下端毛细管，并保证毛细管断口的密封，插上冰箱电源（如压缩
机能工作），使系统中的 Ｒ６００ａ 制冷剂经压缩机排到过滤器，再经排气钳排到室外。
（如压缩机不能工作，则将冰箱移至室外无火源处排气，之后进入第四步）
1)、冷藏室显示 “--” 说明： 当环境温度低于0°C 时，冰箱没有任何问题。 冷藏室只能显示0°C 以上的温度。
5
#Electrolux 自 由 空 间 系 列 冰 箱 ＢＣＤ－２６０ＥＩ
③ 约 ５ 分钟后关闭冰箱电源，用手摇晃压缩机，使熔解在压缩机润滑油中的 Ｒ６００ａ 尽
可能的排放干净。再插上压缩机电源继续排放，３ 分钟后，关闭压缩机电源。
两个阀为双稳态阀，它靠交流电源控制， 以 4 个连续的半脉冲正脉冲或负脉冲为最
4
#Electrolux 自 由 空 间 系 列 冰 箱 ＢＣＤ－２６０ＥＩ
小单位来控制电磁阀的流向，零线及火线接反时阀将反向动作。
二极管
℃
报警功能
开门报警（冷藏室／酒室） 分钟
冷冻室超温报警
℃
照明灯：
Ｖ／Ｗ
防触电类别：
ＢＣＤ－２６０ＥＩ ９２５ ０２ ８１－９８ ６０１╳６５９╳１７４２ １３０／６７／６３ ３８ ＳＮ、Ｎ、ＳＴ ７２ 金属银 ＨＶＴ１０ＡＡ ２２０／５０ １８７－２４２ ８５ ０．６７ １６ 内藏平背式 下置抽屉式 ＋２℃ ￣ ＋８℃ ０℃ ￣ ＋６℃（无 １℃） －１８℃ ￣ －２６℃ ＞３ ＞－６℃ ２２０／１０ Ｉ 类
# Electrolux
维修手册 电冰箱
产品代码： ９２５ ０２８ １９８ 型号： ＢＣＤ－２６０ＥＩ 生产厂： 伊莱克斯（中国）电器有限公司
伊莱克斯（中国）电器有限公司技术服务部 出版号：ＣＮ００１６０ 日期： ２００４－４－３０
ＢＣＤ－２６０ＥＩ
目 录
一、主要技术参数 －－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－ １ 二、电路图 －－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－ ２ 三、制冷系统图解 －－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－ ２ 四、控制面板及其说明 －－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－ ３ 五、部件以及说明 －－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－ ４ 六、Ｒ６００ａ 制冷剂排气以及抽空加注的方法 －－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－ ５ 七、故障显示以及处理 －－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－ ７ 八、备件清单 －－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－ １３
三门之风正流行时尚三门冰箱逐个看
三门之风正流行时尚三门冰箱逐个看前言时下，越来越多的家庭开始将三开门冰箱纳入购买议程。
那么三门冰箱都有什么特点呢？下面让我们来看一下。
三门冰箱分为冷藏室，冷冻室和变温室。
其中变温室的作用一是可以补充冷藏、冷冻室的空间上的不足；二是提供0度左右的温度，具有非常好的保鲜功能，这个温度是冷冻与冷藏室不具备的，用于储存即要冷冻又不宜深冻的鱼虾类食品非常合适。
变温室的温度区间对于各个品牌来说，可以调节的范围是不一样的。
从易用性的角度来讲，当然是可以调控区间越大越好。
有些品牌的温度调控是连续可调的，有的则是分档调控的，不是每一个温度都能调节到。
对于用户来来说，当然是连续可调的更好一些，相对来说价格也更贵一些。
说了三门冰箱的好处，那么，现在让我们来看一下三门冰箱都有什么好选择吧。
美菱冰箱BCD-221CHC高光拉丝银美菱冰箱BCD-221CHC属于鲜极系列，它的全新时尚外观，采用仿不锈钢金属拉丝钛银面板，整体门壳成型侧置式拉手，功能性与工艺性的完美结合，流畅，大气，时尚，个性。
美菱冰箱BCD-221CHC拥有三门三温区设计，独立的软冷冻室，专门储存随时准备食用的鱼、肉，新鲜不冻结，营养与柔软共存。
时时保持新鲜。
它的冷冻室智能补偿，聪明的感知冷暖，免去了手动操作温度补偿开关的烦恼，又能带来准确补偿的节能实惠，体现了自动化冰箱的优越。
它的静音五大秘笈给您带来一个安静的使用环境。
触媒除味采用独有的保险魔盒，可以主动吸附和分解冰箱内的异味和有害分子，持久保持冰箱内的空气清新，美食自然更新鲜。
全透明的抽屉与酒瓶架，实用之处尽显。
编辑点评：美菱这款冰箱经济实惠，在三开门冰箱里价格算是较低的，但是价低不代表质低，丰富的功能给您带来不一样的感受，如果您有意，那么就来看看。
价格：2449松下（Panasonic）冰箱NR-C23WP1-W松下NR-C23WP1-W属于纤雅风直冷系列，拥有白色的机身，显得纤秀雅致，浑然天成。
让它在您的居室中成为了一件艺术品。
家电行业产品维修手册
家电行业产品维修手册摘要：本手册旨在为家电行业的维修技术人员提供详细指导，以帮助他们高效地处理各种常见家电故障。
通过本手册的使用，技术人员将能够快速诊断和修复家电产品的故障，提高服务质量和客户满意度。
第一章：引言家电行业作为现代生活中不可或缺的一部分，随着科技的进步和人们对生活品质的追求，家电产品的种类和复杂度不断增加。
随之而来的是家电维修技术人员面临的挑战也日益增加。
本维修手册针对常见的家电产品，提供了一系列故障诊断和修复方法，帮助技术人员快速解决问题。
第二章：常见家电故障2.1 冰箱故障- 无法制冷或制冷效果差- 有异常噪音- 漏水问题2.2 洗衣机故障- 无法正常启动或关闭- 不洗或不甩干衣物- 异常噪音或振动过大2.3 空调故障- 无法制冷或制热- 不工作或自动关机- 有异味或漏水2.4 电视故障- 无法开机或关机- 无图像或图像不清晰- 无声音或声音失真第三章：故障诊断与修复方法3.1 冰箱故障诊断与修复- 检查压缩机与冷却系统- 清洁或更换冷凝器和蒸发器- 更换损坏的压缩机零件3.2 洗衣机故障诊断与修复- 检查电源和控制面板- 检查电机和传动系统- 检查水位开关和水阀3.3 空调故障诊断与修复- 检查电源和电路连接- 清洁或更换空气过滤器- 检查冷凝器和蒸发器的问题3.4 电视故障诊断与修复- 检查电源和信号线路- 清洁或更换显示屏或电子元件- 重置或升级软件系统第四章：维修注意事项4.1 安全操作- 维修时注意电源和电路的安全- 使用绝缘工具和个人防护装备- 遵循相关安全规定和标准4.2 环境保护- 安全处理故障家电的废弃物- 注意使用环保材料和清洁剂- 推广可再生能源和高效能源的使用4.3 服务态度和技巧- 积极主动地与客户沟通和解释维修情况- 耐心、细致地进行故障诊断和修复- 做好维修记录和服务报告，为客户提供参考和保修依据结论：本维修手册提供了家电行业维修技术人员在处理常见故障时的详细指导。
伊莱克斯冰箱说明书
电力蒸汽对衡式锔炉l 操作说明书air-o-steamer 1使用操作总体说明在打开设备使用前,请仔细阅读本使用手册。
本手册对设备的具体使用进行了详细的描述和说明。
如果您想了解更多关于本产品的一些其他信息，请联络您当地的产品销售代理商。
? 请勿在设备顶盖上放置烤盘或烹饪器具，以免阻碍设备排气排烟。
? 定期地（每年至少一次）对设备进行检查和维护。
因此，我们建议用户能与专业的售后服务维修商签订一份维护保养协议。
? 肉针温度探头是很精密的仪器，因此在使用时要特别小心。
不要用它敲击东西，插入食物内时也不要用力过猛；拔出时，也不要硬拉肉针顶部（在使用手推车烤架时要尤其小心）如果肉针探头因操作不正确而损坏，不在保修范围内。
? 在使用混合烹饪程序时，注意温度不要超过200℃-210℃。
在使用此烹饪程序时，温度过高，烤箱密封条的密封性能将会有所减弱。
? 当放入烤盘时，两个烤盘间最好至少相隔40mm，以便促进烤箱内空气对流。
* 特别是选择使用带蒸汽的烹饪程序烤制食物时，切勿在烤箱内向食物洒盐， * 不要烤带酒精的食物。
attn：如果按说明正确安装万能蒸烤箱且选用我们原装烤盘的，能放入烤箱内最高的烤盘也只能在1.6m；如果您购买的附件不是原装的烤盘，那么注意在放入烤盘时，千万不要超过以上规定的高度。
由于在烹饪时，烤盘内的液态物，如：酱汁、油、被熔化的脂肪等，可能会溅出烤盘外。
如果高于这个高度，那么放在最高的烤盘内食物的烹饪情况，操作人员就无法看到了。
1．开门我们万能蒸烤箱的门锁带有安全设计装置，以免操作人员在打开烤箱门时被大量涌出的蒸汽灼伤。
根据不同型号，请选择以下相应的步骤操作：1.1 6格和10格的烤箱重要！当心灼伤！烤箱内热时，务必小心开门！a. 将门把手随意向哪个方向拉到底。
由于安全装置的作用，此时的门只被打开一条缝。
如果此时正在进行烹饪的话，烹饪程序将被打断。
2 b．松开门把手，然后重复以上“a”的操作步骤，把门完全打开。
伊莱克斯ZMM2200 2420KVA系列冰箱维修手册
伊莱克斯ZMM2200/2420KVA系列冰箱维修手册
目录
一、产品外观结构特征图
二、产品部件结构名称
三、技术参数
四、箱内基本配置
五、制冷系统原理图
六、电气原理图
七、内部结构管路实物图
八、零部件拆卸方法
九、压缩机技术参数（NC1111Y 220-240V ～50Hz LBP）
十、总装分解图
十一、接线图
一、产品外观结构特征图
二、产品部件结构名称
三、技术参数
三、箱内基本配置
四、制冷系统原理
制冷系统制冷剂走向流程图
五、电气系统原理图
六、内部结构管路实物图
七、零部件拆卸方法
1、门开关的拆卸
2、照明灯的拆卸
九、压缩机技术参数（NC1111Y 220-240V ～50Hz LBP）
1、压缩机接线图（RSCR）
4
5
7、安装须知
非冷凝气体限制在：1%
最大打开连接器时间：15分钟
压缩机不能承受高电压或者在真空条件下启动、运行，不能用压缩机进行系统抽真空。
压缩机工作时与水平状态倾斜不大于5°
使用非指定类型的冷冻机油：禁止
压缩机回液：不允许
十、总装分解图
十一、接线图。
伊莱克斯（凯美乐）手动控制“J”系列顶装冰箱维修手册说明书
© Copyright 2006 ELECTROLUX HOME PRODUCTS PTY LTD Technical ServicesELECTROLUX HOME PRODUCTS PTY LTDABN 51 004 762 341ELECTROLUX(KELVINATOR)MANUALLY CONTROLLED“J” SERIESTOP MOUNTREFRIGERATORSMODELSN280J (White) N300J (White) N330J (White) N360J (White) N390J (White)N390SJ (Stainless Steel) N420J (White) N440J (White)N440SJ (Stainless Steel) N520J (White)N520SJ (Stainless Steel)WEB SITE ADDRESS: .auFrom S/Nº 42455916On Models N280J, N300J &N330J deletion of the Pre Cooler Assy.INDEXSECTION PAGE Nº Index 2Specifications 3 - 5The Parts of The Refrigeration 6Performance Parameters 7 - 8Removal and Replacement of Door Handles 9Removal of Light Lens & Rear Control Housing 10 - 13 Removal of Top Control Housing 14 - 15 Removal of Deodoriser Cover 16How to Move the Front Half Shelf under the Rear Half Shelf 17Removal of Split Shelving 18Removal of Crisper Cover 19Adjustment of the Deli Bin 20To Disassemble the Support Frame & Deli Bin 21Adjustment of the Snugger 22Removal and Replacement of Evaporator Cover 23Removal and Replacement of Gaskets 24 - 25 Access to Pre cooler and Defrost tray 25Installation 26 - 29 Air Flow 30Refrigeration Diagram 31Refrigeration Diagram Models N280J, N300J, N330J32from S/Nº 42455916Circuit/Wiring Diagrams 33 - 37Page 2 RESI108SPECIFICATIONSDESCRIPTION N280J N300J N330J DIMENSIONSHeight (mm) 1550 1620 1720Width (mm) 607 607 607Depth (mm) 681 681 681Total Capacity (Litres) 286 303.1 328.4COMPRESSOR PART Nº Embraco1442389Embraco1442389Embraco1442389Type ECR 55 HLP ECR 55 HLP ECR 55 HLP Run Winding (ohms) 14.8 14.8 14.8 Start Winding (ohms) 17.2 17.2 17.2 Run Amps 0.49 0.49 0.49 Starting Amps 8.5 8.5 8.5Oil Charge (cc) 280 280 280CONTROL PART Nº Daesung1444849Daesung1444849Daesung1444849TypeMidCut-in (ºC) 6.5+/-1.2 6.5+/-1.2 6.5+/-1.2 Cut-out (ºC) 2.5+/-1.2 2.5+/-1.2 2.5+/-1.2 MANUAL BAFFLEPART Nº 144119514411951441195 DEFROST TIMER PART NºType 8 Hour / 5 mins drip143982114398211439821D.T.T. PART NºTypeCut-In (ºC)Cut-Out (ºC) 1442102Inchang0.0+/-2.511+/-2.51442102Inchang0.0+/-2.511+/-2.51442102Inchang0.0+/-2.511+/-2.5THERMAL FUSE PART Nº 1442642 1442642 1442642HEATER DEFROST PART Nº 1440999 1440999 1440999 (watts) 325 325 325 (ohms) 177 177 177FAN MOTOR PART Nº Shinhan Tech1444850Shinhan Tech1444850Shinhan Tech1444850FAN BLADE PART Nº 1435563 1435563 1435563INTERIOR LAMP FC PART Nº 1442001 1442001 1442001 Type 25w E14SES Blue 25w E14SES Blue 25w E14SES BlueCAPACITOR RUN PART Nº Rating14367154uf - 400v14367154uf - 400v14367154uf - 400vREFRIGERANTType R134a R134a R134aCharge (grams) 100 100 100Page 3 RESI108SPECIFICATIONSDESCRIPTION N360J N390J/SJ N420J DIMENSIONSHeight (mm) 1640 1720 1640Width (mm) 702 702 702Depth (mm) 681 681 743Total Capacity (Litres) 367.8 392.5 415.6COMPRESSOR PART Nº Electrolux1442337Electrolux1442337Electrolux1442337Type GVT 66 AA GVT 66 AA GVT 66 AA Run Winding (ohms) 15.9 15.9 15.9 Start Winding (ohms) 16.5 16.5 16.5 Run Amps 0.56 0.56 0.56 Starting Amps 8.5 8.5 8.5Oil Charge (cc) 230 230 230CONTROL PART Nº Daesung1446274Daesung1446274Daesung1446274TypeMidCut-in (ºC) 5.5+/-1.2 5.5+/-1.2 5.5+/-1.2 Cut-out (ºC) 1.5+/-1.2 1.5+/-1.2 1.5+/-1.2 MANUAL BAFFLEPART Nº 144119514411951441195 DEFROST TIMER PART NºType 8 Hour / 5 mins drip1439821 1439821 1439821D.T.T. PART NºTypeCut-In (ºC)Cut-Out (ºC) 1442102Inchang0.0+/-2.511+/-2.51442102Inchang0.0+/-2.511+/-2.51442102Inchang0.0+/-2.511+/-2.5THERMAL FUSE PART Nº 1442642 1442642 1442642HEATER DEFROST PART Nº 1441000 1441000 1441000 (watts) 350 350 350 (ohms) 165 165 165FAN MOTOR PART Nº Shinhan Tech1444850Shinhan Tech1444850Shinhan Tech1444850FAN BLADE PART Nº 1435563 1435563 1435563INTERIOR LAMP FC PART Nº 144200114420011442001 Type 25w E14SES Blue 25w E14SES Blue 25w E14SES BlueCAPACITOR RUN PART Nº Rating14367154uf – 400v14367154uf – 400v14367154uf – 400vREFRIGERANTType R134a R134a R134a Charge (grams) 110 110 110Page 4 RESI108SPECIFICATIONSDESCRIPTION N440J/SJ N520J/SJDIMENSIONSHeight (mm) 1720 1720Width (mm) 702 802Depth (mm) 743 743Total Capacity (Litres) 441.5 517.1COMPRESSOR PART Nº Electrolux1442337Electrolux1442336Type GVT 66 AA GVT 75 AA Run Winding (ohms) 15.9 14.9 Start Winding (ohms) 16.5 16.7 Run Amps 0.56 0.67 Starting Amps 8.5 9.92Oil Charge (cc) 230 230CONTROL PART Nº Daesung1446274Daesung1446274TypeMidCut-in (ºC) 5.5+/-1.2 5.5+/-1.2 Cut-out (ºC) 1.5+/-1.2 1.5+/-1.2 MANUAL BAFFLEPART Nº 14411951441195 DEFROST TIMER PART NºType 8 Hour / 5 mins drip1439821 1439821D.T.T. PART NºTypeCut-In (ºC)Cut-Out (ºC) 1442102Inchang0.0+/-2.511+/-2.51442102Inchang0.0+/-2.511+/-2.5THERMAL FUSE PART Nº 1442642 1442642HEATER DEFROST PART Nº 14410001441001 (watts) 350 375(ohms) 165154FAN MOTOR PART Nº Shinhan Tech1444850Shinhan Tech1444850FAN BLADE PART Nº 1435563 1435563INTERIOR LAMP PART Nº 1442001 1442001 Type 25w E14SES Blue 25w E14SES BlueCAPACITOR RUN PART Nº Rating14367154uf – 400v14367154uf – 400vREFRIGERANTType R134a R134aCharge (grams) 110 130Page 5 RESI108Page 6 RESI108THE PARTS OF THE REFRIGERATORPERFORMANCE PARAMETERS (MANUAL REFRIGERATORS)These parameters are guideline for service personnel only.STORAGE TEMPERATURESThe following table is a guideline for temperatures and run times expected for standard top mount Electrolux/Kelvinator J Series product operating in climate temperatures of approximately 20 to 30°C set on MID freezer and MID refrigerator settings:Freezer -19°C to –16°CFood 2°C to 4°C30°C Run Time ~50% Doors closed20°C Run Time ~35% Doors closedThe product is fitted with a thermostat as the refrigerator compartment control and a baffle as the freezer control.Setting the refrigerator control (the thermostat) colder or warmer will set BOTH the freezer and the refrigerator colder or warmer. The thermostat is designed to provide refrigerator compartment temperatures of –2 to 1°C on coldest, and 5 to 8°C on warmest, depending on the altitude and climate that the product is operating in.Setting the freezer control (the baffle) colder or warmer will set ONLY the freezer colder or warmer. One notch movement of the baffle will adjust the freezer temperature by approximately 1°C.The storage temperature in each product will vary depending on the climatic temperature, the altitude, and the usage pattern of each customer. MID freezer and MID food compartment settings are the best starting settings but customers should adjust gradually to suit their storage temperature preference, the climate that they live in, the altitude they live at and how theyuse the product.Why does climatic temperature variance affect storage temperature?For the basic customer requirement of preserving food safely an electromechanical thermostat and baffle system is ideal. When the climatic temperature gets very hot or very cold then the customer may need to adjust the baffle to maintain their preferred storage temperatures. This is because as the climate gets very cold then there is only minor cooling required to keep the refrigerated section of the product cold. Because the thermostat is best located in the refrigerator section then the freezer tends to warm up. This can be overcome by setting the freezer colder, which directs more air to the freezer section when the fan and compressor come on.Likewise when the climate temperature gets very hot the refrigerator section will be running for longer periods and overcoming lots of door openings as customers refresh in the hot weather. The freezer will tend to run colder in these conditions so it can help to save energy and give the refrigerator more capacity to recover from the higher usage if the freezer is set warmer.Page 7 RESI108Why does altitude variance affect storage temperature slightly?Thermostats consist of an expanding/contracting vessel filled with refrigerant. As the refrigerant warms up it expands and completes an electrical circuit which turns the fridge on. As altitude increases, that is we get higher above sea level, then atmospheric pressure decreases. That means that the vessel has to heat up a little less to complete the electrical circuit. The net result is that a product operating approximately 1000m above sea level will operate approximately 1-2°C colder than it would at sea level. The product should be set slightly warmer in these regions to compensate.THERMOSTAT OPERATIONThe cut out and cut in temperatures of the thermostat at sea level are:1446274Coldest Mid WarmestCut In 1.5 ± 2.0 5.5 ± 1.2 9.5 ± 2.0Cut Out -2.5 ± 2.0 1.5 ± 1.2 5.5 ± 2.01444849Coldest Mid WarmestCut In 3.0 ± 2.0 6.5 ± 1.2 10.5 ± 2.0Cut Out -1.5 ± 2.0 2.5 ± 1.2 6.5 ± 2.0Note that the thermostat has a rotation of 305°. These figures are for the thermostat as fitted to the control housing for which only 180° adjustment is available.DEFROST SYSTEMGeneral defrost system parameters:Time Between Defrosts - 8 Hours Compressor On TimeHeater on Time - VariableDry Defrost - Expect 8 to 12 minutes heater on timeHigh Usage Tropical Climate - Expect up to 30 minutes heater on timeDrip Time After Defrost before- 5 minutesCompressor Start upDefrost Termination Thermostat - Bi-Metal- Cut In 0°C, Cut Out +11°CThermal Fuse - +72°C Blown Cut OutWhy does the freezer sometimes hiss, is gas leaking?To achieve the frost free cooling environment moisture and ice need to be removed from the product. Depending on usage and climate the product will “defrost” the cooling system which is located in an insulated compartment at the back of the freezer. The hissing sound is not a gas leak but water dripping onto the heating element used to melt and remove the ice. These generally happen approximately once a day for 20 minutes and insulated and shielded so food storage quality is not compromised during this period.Page 8 RESI108Page 9 RESI108REMOVAL OF DOOR HANDLESPage 10 RESI108REMOVAL OF THE LIGHT LENS AND REAR CONTROL HOUSINGGives access to the Lamp, Thermostat & Manual Baffle.Remove the knobs.To access the manual damper, either remove the gasket, or slit it at the points indicated by the arrows. The insulation block can then be hinged back to access the damper. When re assembling,the gasket must be replaced or resealed at the slits.REMOVAL OF THE TOP CONTROL HOUSING Gives access to the Defrost Timer.Remove the Rear Control Housing first.REMOVAL OF THE DEODORISER COVERTO SLIDE THE FRONT SHELF UNDER THE REAR SHELFREMOVAL OF THE FRONT SHELF FROM THE ASSEMBLYREMOVAL OF THE CRISPER COVERADJUSTMENT OF THE DELI BINIt is possible to slide the Deli Bin from side to side. Two slides (LH & RH) control the air flow to the bin.TO DISASSEMBLE THE SUPPORT FRAME & DELI BINADJUSTMENT OF THE SNUGGERTO REMOVE/REPLACE EVAPORATOR COVER(Gives access to Fan Motor/Blade, Evaporator, Defrost Heater, Thermal Fuse, Defrost Termination Thermostat & Drain Trough)To remove the evaporator cover, use a hooked tool similar to the one in the drawing belowTwo plug buttons covering the screws can be removed with a flat bladed screwdriverCarefully warming up the evaporator cover with a hair dryer will make it pliable for removal. Place the hooked tool pointing downwards into the bottom corners of the louvres (as indicatedby the arrows). Pull on the tool until the clips on the rear of the cover disengage to the extentthat the cover is removable by hand.To refit, position the evaporator cover into the rear of the freezer and push firmly to lock theclips into place.TO REMOVE/REPLACE DOOR GASKETSTo remove the door gasket, start in one of the corners and pull perpendicular to the inner door panel. Once it is released from the corner it can then be peeled off the remainder of the door.To fit a gasket, start by pressing it into the corners first.With the gasket fitted into the corners, move around the door pressing the gasket into the inner panel groove using your thumbs.TO ACCESS THE PRE COOLER AND DEFROST TRAYTilt the refrigerator backwards and support. The pre cooler and defrost tray should be visible on the underside of the cabinet. Unclip the three clips on the LH and RH pre cooler brackets. Easethe pre cooler downwards to access both the pre cooler and defrost tray.INSTALLATIONCLEARANCES AROUND THE REFRIGERATOR Recommended minimum clearances are :• 3cm on each side.• 9cm above the refrigerator.• 5cm behind the refrigerator.The refrigerator should arrive with the front adjustable rollers wound down to tilt the top of the refrigerator backwards by about 10-15mm from the upright. The stability foot should also be wound fully up so it will not interfere with the operation of the rollers.WARNING: The rollers are designed for forward and backward movement only. They are not castors. Moving the refrigerator sideways may cause damage to the floor and rollers.• Roll the refrigerator into its final position.• The top of the refrigerator should be tilted back by approximately 10-15mm. This will allow the doors to self-close providing a consistent door seal. It is normal for the freezer door tomomentarily open and reclose when the food compartment door is closed firmly. If the freezer door stays open you will need to tilt the refrigerator backwards a little further.• If the refrigerator is not tilted back, you can adjust the two front rollers by turning the large plastic roller nut. This will increase the height of the rollers. One turn of the nut will tilt the refrigerator back approximately 10mm. If you have difficulty turning the roller nut you can have someone tilt the refrigerator back, so that you have better access. Alternatively, you can access the rollers from the side, using a flat screwdriver to help you turn the nut.• If the refrigerator now rocks from one corner to the opposite rear corner, this means that the flooris uneven, you will need to put some packing under one of the rear rollers. You could use thin pieces of solid material, such as thin board, vinyl floor tiles or laminate. Place the packing so that it will sit under one of the rear rollers when the refrigerator is rolled into position.• Check the alignment of the refrigerator to the surrounding cupboards. The top of the refrigeratorshould be level from side to side. If you need to adjust the level, use the adjustable rollers.When you have the refrigerator in its final position wind the stabilising foot down until it just makes contact with the floor. When you need to move the refrigerator, be sure to wind the foot back up so that the refrigerator can roll freely.Stabilising foot wound down.AIRFLOW DIAGRAMREFRIGERATION DIAGRAMREFRIGERATION DIAGRAMFor Models N280J, N300J, & N330J from Serial Number 42455916WARNINGIT IS ILLEGAL FOR PERSONS OTHER THAN LICENSED ELECTRICAL MECHANICS OR PERSONS AUTHORISED BY LEGISLATION TO WORK ON THE FIXED WIRING OF ANY ELECTRICAL INSTALLATION. PENALTIES FOR CONVICTION ARE SEVERE.IMPORTANT SAFETY NOTICEThis diagram has been prepared for use by electrically qualified service technicians. The manufacturer cannot be held responsible for the interpretation of its service publications nor for any injury or damage that may occur in connection with their use.WARNINGPERSONS OTHER THAN LICENSED ELECTRICAL MECHANICS OR PERSONS AUTHORISED LEGISLATION TO WORK ON THE FIXED WIRING OF ANY ELECTRICAL INSTALLATION. PENALTIES FOR CONVICTIONIMPORTANT SAFETY NOTICEThis diagram has been prepared for use by electrically qualified service technicians. The manufacturer cannot be held responsible for the interpretation of its service publications nor for any injury or damage that may occur in connectionWARNINGIT IS ILLEGAL FOR PERSONS OTHER THAN LICENSED ELECTRICAL MECHANICS OR PERSONS AUTHORISED BY LEGISLATION TO WORK ON THE FIXED WIRING OF ANY ELECTRICAL INSTALLATION. PENALTIES FOR CONVICTION ARE SEVERE.IMPORTANT SAFETY NOTICEThis diagram has been prepared for use by electrically qualified service technicians. The manufacturer cannot be held responsible for the interpretation of its service publications nor for any injury or damage that may occur in connection with their use.WARNINGPERSONS OTHER THAN LICENSED ELECTRICAL MECHANICS OR PERSONS LEGISLATION TO WORK ON THE FIXED WIRING OF ANY ELECTRICAL INSTALLATION. PENALTIES FOR CONVICTIONIMPORTANT SAFETY NOTICEThis diagram has been prepared for use by electrically qualified service technicians. The manufacturer cannot be held responsible for the interpretation of its service publications nor for any injury or damage that may occur in connectionWARNINGIT IS ILLEGAL FOR PERSONS OTHER THAN LICENSED ELECTRICAL MECHANICS OR PERSONS AUTHORISED BY LEGISLATION TO WORK ON THE FIXED WIRING OF ANY ELECTRICAL INSTALLATION. PENALTIES FOR CONVICTION ARE SEVERE.IMPORTANT SAFETY NOTICEThis diagram has been prepared for use by electrically qualified service technicians. The manufacturer cannot be held responsible for the interpretation of its service publications nor for any injury or damage that may occur in connection with their use.。
北京伊莱克斯冰箱不制冷维修售后
冰箱在日常生活中扮演了重要角色，炎炎夏日蔬菜瓜果放冰箱几可以保质还可以保鲜。
毫无疑问，冰箱给生活带来了很大的方便与节省。
可是冰箱也会出问题，冰箱冬季忽然不制冷了，下面就来看看冰箱不制冷的原因。
很明显，是冰箱的质量不过关。
冰箱冷冻室的蒸发器盘管起制冷作用，下接冷藏室。
设计者计算经过冷藏室的时候蒸发器还有一定的制冷效果。
冰箱盘管结露不结霜原因是什么，设计本身没有问题。
你提到的问题应该是在制作蒸发器盘管的时候员工操作失误减小了其缠绕距离致使其到了冷藏室后仍有较强的制冷效果而出现了起霜现象当冰箱处在工作状态，冷藏室后背会出现结霜现象，主要在冷藏室内胆的后背有蒸发器，冷藏室的温度主要依靠该蒸发器来达到设定温度。
为什么会出现冰箱开门回气管结霜_关门不结霜，当冰箱压缩机停止工作温度会回升此时冷藏室后背的霜会化掉，变成水珠，水珠顺后背淌到出水孔，再到蒸发皿蒸发。
冰箱压缩机低压管结霜原因是什么，冰箱制冷主要是通过蒸发器进行制冷，一般冰箱的蒸发器都在冰箱的冷冻室中，蒸发器和冰箱冷冻室的内壁相接触就会产生热交换。
冰箱蒸发器是由S 型的制冷盘组成，冰箱压缩机制造出的气流在流经管道的时候就会使管道温度降低，这时这些管道会间接降低冰箱内壁中的温度。
由于霜是冷的不良导体，所以冷冻室要及时除霜（当霜积至5毫米厚时），清洁后应使冰箱干燥，然后通电制冷，以免立即结霜。
冰箱管路不结霜怎么办，平时可用较小的塑料袋装清水，放入冷冻室里，冻成冰块。
当家里突然停电时，应尽量少开电冰箱门，有冰块在里面，能使冷藏室仍然保持一定的低温，达到食物保鲜。
无霜冰箱更适宜用这种方式保鲜。
一些比较难融化的地方可以用热毛巾进行热敷来融化冰块。
不建议用吹风机来融化，因为吹风机的温度很难拿捏，会容易因为高温导致冰箱内部变形。
如何解决新冰箱多久结霜，冷冻室壁上的霜块开始整块脱落，软木铲轻轻铲去剩余的冰霜，最后，用干净毛巾将四周擦干净。
冰箱对开门中梁结霜怎么办。
经常检查冰箱门封条是否密封。
Whirlpool 自动冰箱水系统和冷气系统维修指南说明书
AutoSentry Double System RL SERVICE PARTSThis parts list contains the service parts andwiring diagrams for this model.Check the modelnumber of the machine requiring the parts to besure that this is the correct parts list.TABLE OF CONTENTSCabinet Assembly..................................................................................................Page2 Water System.........................................................................................................Page3 Refrigeration System..............................................................................................Page4 Evaporator,FM/FME units.....................................................................................Page5 Evaporator,NM/NME units....................................................................................Page6 Gearmotor..............................................................................................................Page7 Control Box............................................................................................................Page8 Wiring Diagrams...................................................................................................Page9AutoSentry Double System RL SERVICE PARTS2346127891011513314115ITEM PART NUMBER NUMBER DESCRIPTION 8A34294-002Front Panel,S.S.9A34287-015Support 10A35593-001Base 1103-1531-01Screw 1202-0836-00Catch13A32435-002Left Side Panel,S.S.1403-1404-12Screw15.A34286-001Center SupportITEM PART NUMBER NUMBER DESCRIPTION 1A34283-002Back panel2A32461-002Top Panel,S.S.3A34038-002Service Panel,S.S.4A33292-002Right Side Panel,S.S.503-0271-00Speed Clip 615-0808-03Emblem,grey 703-1419-22ScrewCabinetAutoSentry Double System RL SERVICE PARTS2389NUMBER NUMBER DESCRIPTION 1503-1394-01Pal Nut16A36154-001Evap.water inlet tube 1702-1338-00Hose clamp 1802-3692-22Drain fitting1902-3826-01Res.overflow hose (rt)02-3826-02Res.overflow hose (left)20A37482-001Reservoir bracket 2113-0840-01Rubber capITEM PART NUMBER NUMBER DESCRIPTION 103-1405-41Cap Screw 2A32890-020Evaporator 302-0929-23Water Seal402-3266-01Reservoir &valve 502-3266-02Float valve 602-3266-03Plunger/seat712-2760-21Water Level Sensor 8A32777-001Retaining Ring for Seal 902-3837-01Drip Pan 1013-0704-00Gasket1102-4663-01Water Shed1216-0835-01Inlet fitting for plastic tubing 1316-1039-01Male connector1413-0895-01Inlet tubing,4ft.req.AutoSentry Double System RL SERVICE PARTS21376846534ITEM PART NUMBER NUMBER DESCRIPTION 102-3319-03Dryer2A32859-001EPR Valve (used on FME2404,NME1854,FME3004and NME2504)A32859-002EPR Valve (used on FM2402,FM3002,NM1852and NM2502312-2135-02Solenoid Valve 411-0548-01Ball Valve511-0488-21R-404A Thermostatic Expansion Valve (used on FME2404and NME1854)16-0825-21R-22Thermostatic Expansion Valve (used on FM2402and NM1852)11-0482-21R-404A TXV use on FME3004and NME2504611-0548-01Ball valve 7A32890-020Evaporator 816-0762-02Sight GlassRefrigeration System5AutoSentry Double System RL SERVICE PARTS21.13-0617-52O-Ring22.02-2916-01Slotted Collar 23.13-0617-45O-Ring24.03-1544-08Soc.Head Screw 25.A34505-020Breaker (Divider)(includes 18&19)26.A38071-022Auger27.A32890-020Evaporator 28.03-1420-03Cap Screw 29.02-4358-01Insulation 30.02-3837-01Drip Pan31.13-0704-00Drip Pan Gasket 32.02-4663-01Water Shed 33.13-0617-49O-Ring 34.03-1408-36Washer35.13-0929-01Insulation donut432292827262325212422203319181615141312111088634ITEM PART NUMBER NUMBER DESCRIPTION 1.Bail clip2.Drain tube holder3.Ice Chute Cover4.Insulation Top (half)5.Ice Chute Body w/ins6.A33102-001Insulation Collar Inside7.02-2929-04Ice Chute Lower8.A37708-021Bin Controls Assy.(set of 2)9.A32930-001Chute Gasket 10.03-1405-52Hex Cap Screw 11.02-3001-01Ice Sweep 12.13-0871-01Water Shed 13.02-2978-01Lip Seal14.02-3128-20Breaker Cover 15.13-0617-54O-Ring16.08-0660-01Auger Stud,thrust washer 17.A35419-020Strap kit 18.A34559-020Bearing 19.02-2977-01Lip Seal 20.03-1403-27ScrewFM/FME Evaporator,Chute,Bin Controls1235124292629232521241918161514131211108863172028ITEM PART NUMBER NUMBER DESCRIPTION 1.A34969-001Bail clip2.02-3268-01Drain tube holder3.02-2930-04Ice Chute Cover4.A32963-001Insulation Top (half)5.02-3841-01Ice Chute body w/ins6.A33102-001Insulation Collar Inside 6a A35419-020Strap kit7.02-2929-04Ice Chute Lower 8.A37708-021Bin Controls Assy.(set of 2)9.A32930-001Chute Gasket 10.03-1405-52Hex Cap Screw 11.02-3001-01Ice Sweep 12.13-0871-01Water Shed 13.02-2978-01Lip Seal14.02-3128-20Breaker Cover 15.13-0617-52O-Ring16.08-0660-01Auger Stud &washer17.02-4663-01Water Shed 18.A34559-020Bearing 19.02-2977-01Lip Seal20.13-0704-00Drip Pan Gasket 21.13-0617-54O-Ring 22.02-3826-01Drip Pan 23.13-0617-45O-Ring24.03-1544-08Soc.Head Screw 25.A32900-020Breaker(includes 18&19)26.A38071-022Auger27.A32890-020Evaporator 28.03-1420-03Cap Screw 29.02-4358-01Insulation3013-0929-02Insulation donut30*NOTE:GEARCASECOVERINCLUDES COVER,OUTPUT SHAFT,KEY, OUTPUT GEAR,BEARINGS,ANDSEAL.3 59721ITEM PARTNUMBER NUMBER DESCRIPTION1.12-2430-24Start switch,Emerson12-2430-44Start switch,GE/Regal Bel2.12-2430-22Drive Motor208-230v3.02-4663-01Water Shed.4.12-2430-29Bearing-Emerson12-2430-49Bearing-GE/Regal Beloit5.A32379-029Seal,Output6.A32379-024First Gear&Bearing7.A32379-0232nd Gear&Bearing8.A32379-021Gasket9.A32379-020Gear Case10A32379-027Oil,1Container11.A32379-022Gearcase Cover*12.A32379-026Bolt(6)13.A33220-022Complete GearmotorAssembly.208-230v.A33220-030Gearcase kit,no motorAutoSentry Double System RL SERVICE PARTS321Control Box ITEM PARTNUMBER NUMBER DESCRIPTION112-2835-22Circuit Board212-2350-01Stand off312-0426-01Mode SwitchNot Illustrated:412-0813-04Terminal Strip5A34055-001Control Box CoverAutoSentry Double System RL SERVICE PARTSWiring DiagramSEE NAMEPLATEFOR SUPPLY VOLTAGE AND MAX FUSE SIZEEARTH GROUNDBKBK17-2677-01ALL CONTROLS SHOWN IN ICE MAKING MODEUSE COPPER CONDUCTORS ONLY THIS UNIT MUST BE GROUNDEDCONDUCTIVITY PROBEBK R BKBKRGNV789456123412563BKMODE SWITCHT1T2BU YLIQUID LINE SOLENOIDRNCCENTRIFUGAL SWITCHS T A RT R U N OL AUGER DRIVE MOTOR2S -A 1BIN FULL EMITTER (LED)L2L1TERMINAL BLOCK14BU BU BIN FULL DETECTOR(PHOTO TRANS)YCIRCUIT BOARDJUNCTION BOXBKBKCONDUCTIVITY PROBEBKR BKBKRGNV789456123412563BKMODE SWITCHT1T2BUYLIQ LINE SOLENOIDRNCCENTRIFUGAL SWITCHS T A R T R U N OL AUGER DRIVE MOTOR2S -A 1BIN FULL EMITTER (LED)L2L1TERMINAL BLOCK14BU BUBIN FULL DETECTOR PHOTO TRANSYCIRCUIT BOARDCONTROL BOX CONTROL BOXBK BKAutoSentry Double System RL SERVICE PARTSAUGER DRIVERELAYL2L1AUGER MOTORAUGER MOTORAUGER DRIVE Schematic DiagramBulletin Number:PS-14-96Bulletin Date:September 1996Subject: NME, FME, NSE, NDE and TDE550/650 Top Bearing Lubrication Two parts have been made available as helpful aids to use when lubricating the top bearing.1. 02-3559-01 is a needle that snaps onto a standard grease gun fitting. Use it to insert and deeply pack the proper lubricant into the top bearing.2. A36808-001 is a tube of the proper lubricant, also designed to fit a standard grease gun.Both numbers are in the parts price list.Needle, shown inserted into bearing SERVICE BULLETIN。
家用电器维修手册
家用电器维修手册【家用电器维修手册】（正文开始）一、引言家用电器是我们日常生活中必不可少的设备，但是在长期使用过程中，难免会出现一些小故障。
为了提供更好的用户体验，本手册将为大家介绍家用电器的常见故障及其简单维修方法。
二、空调维修1. 电源无法启动- 检查电源插头是否插牢；- 确认电源是否正常供电；- 检查空调控制面板是否正常工作。
2. 制冷效果差- 清洁过滤网，确保空气流通畅；- 如果仍然无法解决，可能是压缩机漏氟，需要联系专业维修人员。
三、冰箱维修1. 冰箱不制冷- 检查电源线是否插牢；- 清洁冰箱后方的散热片；- 检查温度调节器是否正确设置。
2. 冰箱漏水- 检查下水口是否堵塞；- 检查密封胶条是否完好无损；- 如问题仍未解决，可能是冷凝水管道破裂，需请专业人员维修。
四、洗衣机维修1. 洗衣机无法启动- 检查电源是否通电；- 检查开关状态。
2. 洗衣机漏水- 检查洗衣机底部的排水管是否堵塞；- 检查洗衣机密封胶圈是否破损。
五、电饭煲维修1. 电饭煲加热不均匀- 保持内胆清洁；- 检查发热管是否损坏。
2. 电饭煲无法启动- 检查电源是否接通；- 检查电线是否破损。
六、电视维修1. 显示屏无法显示画面- 检查电视是否正常通电；- 检查是否选择正确的输入信号源。
2. 声音问题- 检查音量设置是否正确；- 检查外接音响设备是否接触良好。
七、总结本手册仅提供了家用电器常见故障的简单维修方法，并不能解决所有问题。
在遇到更严重的故障时，请务必联系专业维修人员进行检修和维护。
通过正确的维修方法和日常保养，可以延长家用电器的使用寿命，提高生活品质。
（正文结束）注：本手册仅提供一些常见的家用电器维修方法，实际维修操作需要根据具体情况和设备品牌进行操作。
在进行任何维修操作之前，请先确保电器已经断电，以避免电击和其他意外伤害。
伊莱克斯空调维修常见故障
伊莱克斯空调维修常见故障一、伊莱克斯KFR—65LW/D、KFR一28GW、KFR一25GW、KF-25GW空调强制开机方法：（1）先按住应急开关，再接通220V电源—自检测一LED全亮一继电器（全部）吸合一再按一次，切断。
（2）按住开关面板上应急按钮5秒钟以上，进人强制制冷方式。
二、伊莱克斯KFR—26GW*2、KF—27GW*2、KFR—34GW、KFR—33GW空调强制开机方法：将面板上的拨动开关拨至“试运转”状态，便可进人强制制冷方式。
三、伊莱克斯定速柜机强制开机方法：定速柜机一般情况下，同时按住温度调节“上”、“下”两个键，即可进人强制制冷方式。
此时空调先自检测传感器故障，若有蜂鸣器响6声后显示故障代码，之后压缩机无延时，进行模式切换时压缩机不停。
四、伊莱克斯KFR—35GW、KFR一40GW/BP，KFR－32GW／BP、KFR—36GW／ABP空调用遥控器设定“制冷”模式开机，将开关面板上的拨动开关由“开”拨至“试运转”，进入强制制冷方式，此时定频。
五、伊莱克斯KFR—3601GW/BP、KFR-3602GW/BP、KFR一4001GW/ZBP、KFR—4501GW/BP，空调强制开机方法：（1）按住应急开关一次为开机，再按一次为关机。
控制器根据室温自动判断进人相应的工作模式。
工作模式一旦确定，不能改变，除非切断电源重新上电。
①室温＞26℃时，制冷运行，室内温度设定为26℃，室内风设定为自动。
②室温＜23℃时，制热运行，室温设定为23℃，室内风设定为自动。
③23℃＜室温＜26℃时，送风运行，室内风速设定为自动。
（2）空调器通电后按住应急开关停留5秒以上，控制器进人试运行，试运行为强制制冷，与室温无关。
（3）按住应急开关后接通电源，空调器室内机蜂鸣器响2声后，进入自检状态。
制冷设备毛细管内径的测试方法使用方法：把被测毛细管的一端弄直7～8cm，否则影响测量精度。
用剪刀在距离端头2cm处环切一圈，用钳子掰断。
Electrolux 冰箱维修手册说明书
SERVICE MANUALREFRIGERATION ©Electrolux Home Products S.p.A.Spares Operations ItalyCorso lino Zanussi, 30I - 33080 Porcia (PN)Fax +39 0434 394096S.O.I.Edition: 11.2006Publication no.599 38 43-56ENREFRIGERATORSwithelectric valveandelectronicERF2000DIGITSFACTORY: ZSCONTENT1INTRODUCTION (3)2REFRIGERATION CIRCUIT (5)3ELECTRIC WIRING (6)4COMPONENTS (8)4.1Control panel (8)4.2Electronic boards (9)4.2.1 ERF2000 Power board (10)4.2.2 ERF2000 DIGITS Display board (12)4.3Cooler and freezer compartments (13)4.3.1 Temperature sensors (14)4.3.2 Door switch (14)4.4Compressor compartment (14)4.4.1 Electric valve (15)5MAIN FUNCTIONS (16)5.1Normal (16)5.2FROSTMATIC Function (rapid freezing) (17)5.3COOLMATIC Function (rapid cooling) (17)5.4HOLIDAY Function (valid only for the cooler) (17)5.5Malfunctioning of cooler air temperature sensor (18)5.6Malfunctioning of freezer temperature sensor (19)6ALARMS (20)6.1Freezer compartment temperature alarm (20)7SPECIAL FUNCTIONS (21)7.1Service Mode (21)7.1.1 Starting Service Mode (21)7.1.2 Exiting Service Mode (21)7.1.3 Functions of the Service Mode (21)7.2DEMO MODE (23)7.2.1 Start DEMO MODE (23)7.2.2 Exit DEMO MODE (23)7.2.3 Functions of the DEMO MODE (23)8ACCESSIBILITY (24)8.1Control panel (24)9DISPLAY SYMBOLS (25)9.1Cooler compartment (25)9.2Freezer compartment (26)1INTRODUCTIONThis manual describes the refrigerators with electric valve and ERF2000 DIGITS electronic produced in the Susegana factory called ZS.These models feature:-static (static freezer, static cooler)-total built-in-DOOR ON DOOR door system-single-compressor-electronic control (electronic board ERF2000)-electric valve-digit displayThey are appliances (KBI290DVIT) with the following PNCs:PNC MODEL BRAND925701653JKG9499Juno-Electrolux925701654SC91840-5I AEG-Electrolux925701655SC81840-5I AEG-Electrolux925701656SC81840-5I AEG-Electrolux925701659ERO2923Electrolux925701660ERO2924Electrolux925701661JKG9499Juno-Electrolux925701662SC91840-5I AEG-Electrolux925701663SC91843-5I AEG-Electrolux925701664463.688-2Privileg925701665ERO2923Electrolux925701666ERO2923Electrolux925701667DRC629JE De Dietrich925701668IKE318-5-2Küppersbusch925701669DRC629JE De Dietrich925701670IKE318-5-2Küppersbusch925701671JCG94180Juno-ElectroluxThe controls of the appliance are inserted inside the upper crosspiece.The power control board is ERF2000.The user interface board is ERF2000 (DIGIT display).The appliance has a single-compressor and an electric valve is installed to simulate the operation of a two-compressor.It is possible to switch off only the cooler compartment and let the freezer operate, but not vice versa.The temperatures regulation is the following:•from +8 to +2 °C for the cooler;•from -15 to -24 °C for the freezer.The DIGIT display enables to show the temperatures of the two compartments. The appliance has the following functions:•rapid freezing;•rapid cooling;•freezer temperature alarm,•cooler compartment holiday.The appliance consists of the following compartments:•freezer;•cooler.The evaporating circuit consists of:•roll bond plate evaporator (freezer);•tube evaporator (cooler compartment).Key:A = control panelB = cooler compartmentC = freezer compartment2REFRIGERATION CIRCUITKey:pressor;2.condenser;3.anti-condensation coil;4.dehydrator filter;5.electric valve;6.tube evaporator (cooler compartment);7.plate evaporator (freezer compartment);8.exchanger.The electric valve has 2 outlet capillaries to power:•cooler + freezeror•only the freezer.3ELECTRIC WIRING(Check the specific diagram for each model!)Key:pressormp31.electric valve28.running capacitor (if featured) 41.ERF2000 power boarda.yellow-greenb.brownc.blued.whitee.black4COMPONENTS4.1Control panelKey:Cooler compartmentA.cooler ON/OFF indicator LEDB.cooler ON/OFF buttonC.cooler temperature increase button (+)D.cooler temperature displayingE.cooler temperature decrease button (-)F.COOLMATIC Function LED (rapid cooling)G.COOLMATIC function button (rapid cooling)Freezer compartmentH.ON/OFF indicator LED refrigeratore+freezerI.ON/OFF button cooler+freezerJ.freezer temperature increase button (+)K.freezer temperature displayingL.freezer temperature decrease button (-)M.FROSTMATIC Function LED (rapid freezing) N.FROSTMATIC function button (rapid freezing) O.alarm pilot lamp LEDP.alarm deactivation button4.2Electronic boardsThe electronic board of the appliance consists of:1.ERF2000 power board2.ERF2000 DIGITS display boardThe two electronic boards are connected by means of a flat cable with a connector; therefore, the two boards are available singularly as spare part.4.2.1ERF2000 Power board- View of the electronic board (side of components):1.earth contact2.free3.linepressor5.neutralmp neutralmp8.neutral electric valve9.electric valve1.free2.free1.cooler air temperature sensor2.cooler air temperature sensor3.cooler evaporator temperature sensor4.cooler evaporator temperature sensor5.freezer air temperature sensor6.freezer air temperature sensor1.free2.free1.free2.free3.free4.free1.free2.free4.2.2ERF2000 DIGITS Display boardKey:SW1= reed elementSW2= ON/OFF button cooler+freezerSW3= FROSTMATIC function button (rapid freezing) SW4= freezer temperature increase button (+)SW5= freezer temperature decrease button (-)SW6= cooler ON/OFF buttonSW7= COOLMATIC function button (rapid cooling) SW8= cooler temperature increase button (+)SW9= cooler temperature decrease button (-)SW10= alarm deactivation buttonDGT1= cooler displayDGT2= freezer displayDL1= COOLMATIC function LED (rapid cooling)DL2= FROSTMATIC function LED (rapid freezing) DL3= alarm pilot lamp LEDDL4= LED sign + coolerDL5= ON/OFF indicator LED coolerDL6= LED sign - freezerDL7= ON/OFF indicator LED cooler+freezer4.3Cooler and freezer compartmentsKey:A.freezer air temperature sensor;B.cooler air temperature sensor;C.cooler evaporator temperature sensor.1.cooler door magnet;2.display board reed element.4.3.1Temperature sensors3 NTC sensors are used to detect the temperatures of the two compartments:•freezer air temperature sensor A (located on the freezer cell);•cooler air temperature sensor B (located on the cooler cell);•cooler evaporator temperature sensor C (located on the cooler cell).The sensors A, B and C feature the foamed cable inside the cabinet, therefore they are not replaceable (for further information, please see Service Bulletin 599374122).4.3.2Door switchThe control of the cooler door opening is carried out by using the magnetic switch located on the display board. The magnetic switch is activated by a magnet located inside the cooler door.The control does not imply the activation of the open door alarm, but it is used to light up the lamp of the cooler compartment.4.4Compressor compartmentKey:pressorB.electric valve4.4.1Electric valveThe electric valve is of the 3-way bistable type.It is supplied together with the dehydrator filter.The connections of the electric valve are the following:-central hose with dehydrator filter to connect the condenser;-side hose (GS) to connect the capillary of the freezer circuit;-side hose (KS) to connect the capillary of the cooler+freezer circuit.The electric valve has the following values:-voltage 220 V - 50 Hz-response time <1 secNote:Comply with the electric connections and do not invert the polarity (the 2 terminals FAST-ON have different dimensions).5MAIN FUNCTIONS5.1NormalIn case of first switching on with a freezer compartment temperature higher than 10 °C, the appliance operates with a test cycle (for the factory) for a maximum time of about 1,5 hours.In this period do not perform tests for the correct operation of the appliance, since the loads of the appliance are activated only for internal check (compressor and electric valve).When the appliance is off then:•the compressor is off;•the displays are off.Pushing the ON/OFF button, the displays switch on with the following displaying:•+ symbol on cooler display;•flashing digits of the freezer;•freezer temperature alarm LED (buzzer active).Push the alarm deactivation button to deactivate the buzzer.Regulate the temperatures of the compartments so as to set the following values:•about +5 °C in the cooler;•about -18 °C in the freezer.Warning: Unplug the appliance before operating.5.2FROSTMATIC Function (rapid freezing)The FROSTMATIC function (rapid freezing) is activated by pushing the relative button, therefore:•The pilot lamp relative to the FROSTMATIC function lights up;•The compressor operates in thermostatic conditions and not continuously (like the temperature knob was on max. position) for a duration of about 52 hours, and then it deactivates automatically.To deactivate the FROSTMATIC function push the relative button.5.3COOLMATIC Function (rapid cooling)The COOLMATIC function (rapid cooling) is activated by pushing the relative button, therefore:•The pilot lamp relative to the COOLMATIC function lights up;•The compressor operates in thermostatic conditions and not continuously (like the temperature knob was on max. position) for a duration of about 6 hours, and then it deactivates automatically.To deactivate the COOLMATIC function push the relative button.5.4HOLIDAY Function (valid only for the cooler)The HOLIDAY function is activated when the customer does not want to use temporary the cooler.In this case it is not necessary to leave the cooler door open, because a 15 °C temperature is automatically set to avoid the formation of bad odours inside.To activate the HOLIDAY function push button + (temperature increase) till letter H is shown in the cooler dis-play.Obviously the cooler must be empty because the 15 °C temperature does not allow the preservation of the most common food.the sensor is out of range), then:When the sensor operates again normally, the above described conditions terminate.Characteristics of the NTC sensor:•The display shows cooler temperature sensor faulty.•The appliance operates with preset cycle when the compressor is powered for 40 minutes andremains off for 40 minutes alternatively.the sensor is out of range), then:When the sensor operates again normally, the above described conditions terminate.Characteristics of the NTC sensor:•The display shows freezer temperature sensor faulty.•The appliance operates with preset cycle when the compressor is powered for 40 minutes andremains off for 40 minutes alternatively.6ALARMS6.1Freezer compartment temperature alarmWhen the freezer compartment reaches -11 °C, the temperature alarm activates:•The display digits flash.•The temperature alarm pilot lamp light up.•The buzzer sounds.Push the alarm deactivation button to deactivate the buzzer.When normal conditions are reset (after a power failure):•The acoustic signal deactivates.•The temperature alarm pilot lamp remains on.•The display digits still flash.Pushing the alarm deactivation button:•The highest temperature reached in the freezer compartment is displayed for 5 minutes.•The alarm pilot lamp switches off.•The display digits do not flash anymore.7SPECIAL FUNCTIONS7.1Service Mode7.1.1Starting Service ModeTo start the procedure, perform the following operations:1.Connect the plug to the socket.2.Switch on the appliance with the ON/OFF button.3.Open the doors of the appliance.4.Switch the appliance off with the ON/OFF button.5.Within the first 10 seconds hold down simultaneously the two buttons “FROSTMATIC function (rapid freez-ing)” and “alarm deactivation”.The confirmation of the procedure start occurs with the acoustic signalling of the buzzer which emits a long beep and with the lighting up of all segments of the display.7.1.2Exiting Service ModeThe procedure terminates when one of the following operations is carried out:a.The plug is detached from the socket and reconnected.b.40 minutes have elapsed and no button has been pushed.c.The last phase of the procedure has been reached.7.1.3Functions of the Service ModePress the button “FROSTMATIC function (rapid freezing)” or “alarm deactivation” to skip to the following phase of the procedure.Prsss the “ON/OFF” button to activate/deactivate the loads (compressor, defrosting heater, lamp, fan and air flow regulator damper).List of the phases of the SERVICE MODE:1.All segments of the display are on.2.All segments of the displays are off.3.The number 0 is shown on the display and the load controlled by ACS TH1 [compressor] is checked.To activate/deactivate the load press the button “ON/OFF” (the load is activated when the rapid freezing FROSTMATIC function pilot lamp and the alarm pilot lamp light up).4.The number 1 is shown on the display and the load controlled by ACS TH2 [electric valve] is checked.To activate/deactivate the load press the button “ON/OFF” (the electric valve switches from one side to the other and it is possible to hear a click).5.The number 2 is shown on the display and the laod controlled by ACS TH3 [lamp] is checked.To activate/deactivate the load press the button “ON/OFF” (the load is activated when the rapid freezing FROSTMATIC function pilot lamp and the alarm pilot lamp light up).6.The number 3 is shown on the display and the load controlled by ACS TH4 [not used in this appliance] ischecked.To activate/deactivate the load press the button “ON/OFF” (the load is activated when the rapid freezing FROSTMATIC function pilot lamp and the alarm pilot lamp light up).Note:When the procedure skips to the following phase pressing the button “FROSTMATIC function (rapid freez-ing)” or “alarm deactivation”, the laod keeps its status (for example, if the compressor had been activated, it will remain on also in the subsequent phases); in this way it is possible to check the loads simultaneously.7.Check of the doors.The display digits correspond to the doors: the unit digits correspond to the cooler door, while the ten digits correspond to the freezer door.If the relative door is closed, the displayed digit is 0 otherwise is 1.8.Check of the counter.The display shows an increasing number at intervals of 1 second.This is a counter used by the board for its internal management.9.Check of the temperature sensors.The display shows one of the following codes:Code DESCRIPTIONE0No errorE1Evaporator sensor damagedE2Room temperature sensor damaged (installed on the display board)E4Room temperature sensor damaged (installed on the power board)E50 degree compartment sensor damagedNote:The errors regarding the cooler and freezer air sensors are already displayed during the normal operation. At this point all the phases necessary to chcek the loads have been displayed, therefore it is advisable to in-terrupt the procedure of the SERVICE MODE unplugging and replugging the appliance.Note:If you do not want to interrupt the SERVICE MODE, the procedure continues with some phases dedicated ex-clusively to the factory, therefore they must not to be considered.Also in this case the exit from the SERVICE MODE is carried out unplugging and replugging the appliance.7.2DEMO MODEThe DEMO MODE function is intended only for the commercial activity and not for the user.The internal temperature of the appliance, measured by the air sensors, must be higher than +10 °C so as the function can be activated.7.2.1Start DEMO MODETo start the procedure, hold down the ON/OFF button cooler+freezer and the freezer temperature decrease button for more than 5 seconds.The display digits flash every about 4 seconds.7.2.2Exit DEMO MODETo exit the procedure, hold down the ON/OFF button cooler+freezer and the freezer temperature decrease but-ton for more than 5 seconds or unplug the appliance.7.2.3Functions of the DEMO MODEThe procedure is used only for show in the selling points and allows selecting the temperatures without acti-vating the loads (compressor and electric valve).The displays show:•+ 5 °C for the cooler compartment (flashing display);•-18 °C for the freezer compartment (flashing display).By pushing the temperature regulation buttons, the displays show the temperatures that can be set (flashing display).The internal light switches on when the cooler door is opened.By pushing the cooler ON/OFF button it is possible to simulate the switching off of the cooler compartment (the lamp is off).8ACCESSIBILITY8.1Control panelTo access the control panel and its components (power and display boards) perform the following operations in sequence:a.Open the cooler door.Warning: Disconnect the appliance from the electric power before operating with theappliance.b) View of the control panel of the upper cross-piece.c) Remove the programme plate removing the 2 screw covers and the 2 fixing screws.d) Remove the transparent foil and extract the con-trol support.e) View of the power board.9DISPLAY SYMBOLS9.1Cooler compartmentDISPLAY DIGITS DESCRIPTIONNOT FLASHING It indicates the cooler temperature with normal function [from +2 to +8].FLASHING It indicates the cooler temperature with DEMO MODE func-tion [from +2 to +8].NOT FLASHING It indicates the HOLIDAY function of the cooler compart-ment [15 °C].NOT FLASHING It indicates the malfunctioning of cooler air temperature sensor.NOT FLASHING It indicates incompatibility between the electronic boards. Remedy: check the spare part nos. of the electronic boards.NOT FLASHING It indicates Eeprom parameter writing/reading error. Remedy: replace both electronic boards (power and dis-play).9.2Freezer compartmentDISPLAY DIGITS DESCRIPTIONNOT FLASHING It indicates the freezer temperature with normal function [from -15 to -24].FLASHING It indicates the freezer temperature with DEMO MODE function [from -15 to -24].NOT FLASHING It indicates the malfunctioning of freezer air temperature sensor.NOT FLASHING It indicates incompatibility between the electronic boards. Remedy: check the spare part nos. of the electronic boards.NOT FLASHING It indicates Eeprom parameter writing/reading error. Remedy: replace both electronic boards (power and dis-play).。