船舶专业英语词汇

1 船舶专业英语词汇（初级）1．基本，简单的词汇：AM 上午 PM下午Notification of inspection 检查验收通知单Application 申请，申请单Inspection 检验，报验Technical discussion 技术讨论On board 在船上In the workshop 在车间On the slipway 在船台上At pier(wharf) 在码头Fair 尚好的The performance is merely fair 性能尚好Terrible 极坏的，很糟的So so 马马虎虎So far ,so good 到目前，一切顺利Worse更糟的worst最差、最糟Improvement 改进Leave no room for improvement 完美，无缺点Accept 接收Accept subject to 有条件的接收，有待于……做好之后才接收Reject 拒收Comments 意见 defect lish 消除意见清单Item 项目memorandum 备忘录manual n、手册、说明书；a.手控的，手工的drawings 图纸working drawings 施工图finished drawings 完工图approved drawings 认可图drawings for approval 送审认可图supporting technical doucuments 基础技术文件sketch 草图 draw a sketch画草图up to the standard 达到标准substandard 低于标准的crane 吊车building berth 船台slipway 船台、下水滑道dry dock 干无坞pier 突码头、突堤wharf 码头along side (船)靠码头foreman 工长，领班coordinator 调度员inspector 检查员supervisor 管理人、监督人，监造人surveyor 验船师2、船体总体，及各类型船舶Hull 船体Forecastle 艏楼Stern 船尾Poop 艉楼Superstructure 上层建筑Foremast 前桅杆After mast 后桅杆Radar mast 雷达桅杆Main deck 主甲板Upper deck 上甲板Poop deck 艉楼甲板Accommodation deck 生活甲板Compass deck 罗经甲板Funnel 烟囱Bridge 桥楼，驾驶台Bridge wing 驾驶室翼桥Wheel house 驾驶室Engine room 机舱Engine control room 机舱集控室Catwalk 天桥、步桥Flying bridge （露天）航行驾驶室Rescue boat 救助艇Life boat 救生艇M/Vmerchant vessels 商船Naval Auxilary vessel 军用船Naval Ship/war shipd 军船Ice-breaker 破冰船Container vessel 集装箱船Oil tanker 油轮Products tanks 成品油轮Carrier 运输船、航空母舰、托架Chemical carrier 化学品运输船Liquefied gas carrier 液化气体船Liquefied natural gas carrier 液化天然气运输船Aircraft carrier/aeroplane carrier 航空母舰School ship/training ship 训练船Geophysical survey ship 地球物理勘探船Cruiser 巡洋舰、大型快船、游艇Canoe 独木船，皮舟Junk 平底中国帆船、舳板Gondola （意大利威尼斯的）一种狭长的平底船Yacht 快艇、游艇Fast boat 快艇Patrol boat 巡逻艇Anti-smuggling boat 缉私艇Torpedo boat 公安艇Ferry 渡船Catamaran 双体船Jet foil 喷水水翼艇Wing assrsted vessel 地效船3、各专业基本词汇1）船体：Draft forward 前吃水Draft middle 中吃水Draft after 后吃水Plimsoll mark/lineWaterline 吃水线Waterlines （型）水线Port 左舷Starboard 右舷Sagging 中垂、下垂、下挂（流）Hogging 中拱、上拱Derformation 变形Fairing 光顺、火工校正Hot work热工、明火作业section 分段、部分、剖面Block 分段Keel （船舶）龙骨Bilge keel 舭龙骨Power tool 带动力工具（风动或电动）Welder 电焊工Welding machine 电焊机A.C welding 交流（电弧）焊D.C welding 直流（电弧）焊Grinding 打磨Welding 电焊Spatters 飞溅（电焊）Under out 咬口Sharp edge 快口2 船舶专业英语词汇（初级）Deflection 挠曲，变形Slags 渣Welding slags 电焊渣Automatic welding 自动焊Manual welding 手工焊Arc welding 电弧焊Gas shielded welding气体保护焊Inter gas arc welding惰性气体保护电弧焊Welding seam焊缝Bending machine 弯曲机Three-roll bending machine三芯弯板机Torsional box抗扭箱V oid space空舱Cofferdam 隔离舱Bulwark舷墙，防浪板Wall墙壁Floor地板Controllable pitch 可调桨Elastic coupling 弹性联轴节Bellow 波纹管Joint接头Gaskets垫片Fitting bolts 拂螺拴Chock 制动块、导缆器Chock fast 环氧垫块Foundation 底座、基座Mounting 装置、座、架Mount （常指火炮等武器的）座，架Vent pipe 透气管Sounding pipe探测管Vapour return line油气回路管Stripping line扫舱管Safety equipment 安全设备Life-saving equipment救生设备Cargo hold 货舱Cargo oil tank货油舱Cabin 船舱、舱室Store room储藏室Cold room冷库Fish room鱼库Meat room 肉库Provision room粮库Foam room 泡沫库CO2 room二氧化碳室Pump room泵室Battery room蓄电池室Radio room 报务室Galley 厨房Ventilation system 通风系统Fresh water piping system 淡水系统Sea water piping system 海水管系Water jacket水套Insulation materials绝缘材料Lagging绝缘材料、外套（锅炉、管子等）3）电器Current电流V oltage电压Frequency频率Contact触点、触头Ballast镇流器Convertor变频器、换能器Conductor导体Semi-conductor半导体Rectifier整流器Transformer变压器Thermostat 恒温器Thermister热敏器Edison base 螺丝灯座、爱迪生灯座Bayonet base卡口灯座On-off开关（量）Analogue模拟，模拟设备Active analogue有源模拟、主动模拟Passive analogue无源模拟、被动模拟Dry contact无源模拟、干接触Buzzer蜂鸣器Button按扭，电扭Switch开关Main switch主开关Main switch board主配电板Cable 电缆Three-core cable三蕊电缆Clamp夹钳、夹具Clip 接线柱、线夹Alligator clip鳄鱼夹、弹簧夹V oltage drop 电压降Speed droop速度降低Black out 黑灯试验Power failure失电Setting point 设定点Adjust 调正（v）Adjustment调正（n）Oscillator振荡器、振动器Oscilloprobe示波器测试头Oscilloscope示波器、示波仪Resistor电阻、电阻器Potentiometer电位器、电势计Electrolysis电解（作用）Electrolyte电解质、电解液setting point of power surplus负载余量设定值重载询问test the power surplus setting point重载询问试验4）漆、木Surface preparation表面处理（清理工作）Blasting equipment喷漆（砂粒）装置Sand blasting 喷砂除锈Pre-blasting预喷砂Lingt blasting 预喷砂Full blasting 通喷砂Sand sweep扫砂Sand blasting to SA2.5喷砂达到SA2.5级Steel work inspection after full blasting通喷砂后钢结构检查Cleanliness inspection清洁度检查Inspection after degreasing除去油脂后检查Removing oil stains by detergent/solvent使用洗洁剂/容剂除去油迹Shop primer 车间底漆Spray painting喷漆、喷涂法Touch-up 补漆、修正Touch-up painting补漆、点漆First coat 底漆、头道漆Finish coat 面漆Surface coat 表面涂层Under coat 内涂层Wearing coat 磨耗层Zinc-rich coating富锌涂层Cement wash coating（薄）水泥涂层Stripe coating 预涂层Floor covering 地板覆层Alkyd resin paint醇酸树脂漆Epoxy(resin-based)paint环氧树脂涂料3 船舶专业英语词汇（初级）Scuttle舷窗Carpet地毯Wooden skirt木裙板（踢脚）Aluminum skirt稆质裙板（踢脚）Brass nose装于楼梯踏步一的黄铜防滑镶条Stainless screw不锈钢螺钉Spring 弹簧Securing dev ice固定件Locking device闭锁装置，制动设备Plywood胶合板，层压板Laminated plate迭层板Laminate层压制品，迭层板，层压板High pressure washing of the hull用高压水冲洗船壳Steel plate temperature 钢板温度Condensation冷凝Capillary condensation毛细管现象Dew point露点Flashing point闪点Ignition point 燃点，着火点Ventilation for coating 涂装通风Dehumidifier去湿机，干燥机Dehumidification 去湿，去潮Sagging流挂，下垂Chalking粉化Peeling剥落（指油漆）Pinhole针孔CureCuring硬化，熟化，硫化Drying film thickness(DFT)干膜（漆膜）厚度Curing temperature硬化、固化温度Power tools有动力的工具（包括电动及风动）Pheomatic tools风动工具Burnt area烧坏的区域Oil stains油迹Scratches划痕Damaged places遭损坏的部位Chicken wire钢丝网Tiles瓷砖，瓦Mosaic-tile彩色瓷砖，镶嵌瓷砖，马赛克瓷砖Glue胶，粘结剂Silica硅石，二氧化碳Silicagel硅胶Decoration装饰，装修Interior decoration内部装饰，内装Deck head 天花板Ceiling天花板Paneling板墙，镶板Wall墙壁Desk书桌，桌台Drawer 抽屉Catch hook固定钩子Observation window 观察窗Inspection window检查孔窗Clear view window旋转观察窗Curtain 窗帘Latch止动销，插销Valance窗帘箱Hanging窗帘Eyebrow舷窗眉板Pre-alarm预报警Trip脱扣，跳闸Preferential trip优先脱扣Transducer换能器synchronize（便）同步synchronize motor同步电机synchronous motor异步电机step motor步进电机diode二极管triode三极管audion三极管single phase单相three phase三相phase-in逐步引进phase-shafting相移retarding phase 滞后相位reversed phase倒相，相反relay继电器timer定时器trimmer微调电容器，调正片delay延时carrier载波，载波电流transponder发射器，应答器，询问机echo-sound回声测深仪radio navigation equipment无线电导航设备log计程仪auto-pilot自动驾驶仪gyro-compass电罗经barrier屏障，障碍，栅栏zenner barrier齐纳屏（使电只能单向流的半导体）radio beacon无线电信标pluse脉冲blanking plus 消隐脉冲induction感应，感应现象oscillation振荡Leak(v)渗，漏Leakage(n) 渗，漏Overhaul大修，彻底检修Hammer榔头Spanner扳手，扳头Ring spanner环形扳手，梅花扳手Allen key 内六角扳手，Box spanner套筒扳手Torque spanner扭力扳手Double-ended spanner双头扳手Monkey spanner活络扳手，活络管扳手Shifting spanner活络扳手Pipe spanner管子扳手Reamer铰刀Reaming （用）铰（刀扩）孔Countersink reamer锥形孔铰刀Wrench扳手，扳头Shisel凿子Calipers卡钳，两脚规Inside calipers内卡钳Bore 内孔Boroscopic inspection内孔表面检查Boroscope内孔表面检查仪Plug塞（子），（内燃机）火花塞Cock施塞，龙头Valve阀P/V valve P/V阀Strainer滤器Coarse strainer粗滤器Fine strainer精滤器Oil separator分油机Back pressure背压Pressure test压力试验Over speed 超速Over load超负荷Dafety device 安全装置Fly wheel飞轮Floating floor 浮式地板Deckhead 天花板（指由甲板形成的）Ladder 梯子Vertical ladder直梯Inclined ladder斜梯Accommodation ladder舷梯Pilot ladder引水员；软梯4 船舶专业英语词汇（初级）2)轮机Centering对中心Alignment对准，对准中心Inspection报验Installation安装Final inspection of M/E insallation主机最终安装报验Inspection of the centering of the stern tabe before fine boring精镗前艉轴管中心校准Alignment check/inspection拉中心/校正报验Completeness inspection of the thermal oil circulating piping system 热油循环管系完整性报验Cleanliness inspection after flushing F.O piping system燃油管串油后清洁检查Function test of steering gear舵机效甩试验Hose test of water tight doors水密门冲水试验Noise lever measurement噪声测量Vibration level measurement 振动测量Main engine (M/E)主机Generator发电机Emergency generator应急发电机Shaft generator轴带发电机Fresh water generator 制淡装置Steering gear 舵机General service pump总用泵Pire pump消防泵Hydraulic motor 液压马达Hydraulic nuts液压螺帽Rudder舵Rudder bl ade舵叶Propeller车叶，螺旋桨Fixed pitch propeller固定螺距的螺旋桨Lofting型线图放样Lay off（船及部件）放样，下料Plate-cutting钢板下料，开工Numerically-controlled cutting machine数控切割机Cutting machine切割机Under water plasma cutting machine水下等离子切割机Surface preparation表面处理Fabrication（焊）开坡口，边缘加工（如刨边）Upside down construction method分段装配Assembly 反身建法Erection装配，大合拢Jig装配架，胎架Bow jip 船首部胎架Girder纵向构件，桁（材）Beam梁，横梁Sections型材Profile型钢（条）Bar 杆，棒,棒材Plate板材Angle bar角钢I beam（窄缘）工字梁H beam（宽缘）工字梁Stiffener扶强材Bracket托架，支架，肘板Support 支架Frame肋骨，框架Douler复板Coaming（舱口）围板，缘材Sinp剪切Anchor锚Anchor widdlass 锚机Anchorage锚位，锚地Chain链Chain block链条滑车，神仙滑车Platform平台Crossover跨越（梯桥），立交Life raft 救身筏Life buoy 救生圈Forward winch 前绞缆机After winch 后绞缆机Windlass锚机Bitt带缆桩，系桩Fairlead导缆钳，导缆孔Hand rail扶手，栏杆Beam横梁Frame肋骨，框架Scantling构件尺寸Cargo oil tank货油舱Scantling draft结构吃水Forepeak tank首尖舱After peak tank尾尖舱Water ballast tanks(W.B.T)压载水舱Fuel oil tank(F.O.T)燃油舱Lubricating oil tank(L.OT)滑油舱Diesel oil tank(D.O.T)柴油舱Double botton双层底Double skin双层外板，双层蒙皮Bow thruster艏侧推Propeller车叶Fixed pitch propeller定螺距螺旋桨Controllable pitch propeller(CPP)可调螺距螺旋桨Shaft轴Tail shart尾轴Shaft generator轴带发电机Watertight doors水密门Bulwark舷墙Bulkhead舱壁Tank top内底，液舱顶Hatch cover舱口盖Manhole人孔Fin stablizer减摇鳍Antifouling system防海生物的，防污染系统Vessel船，舰Fabrication制造，分段装配（precfabrication预制，预加工）Assemble装配，组装Erection大合拢，船台装配Staging脚手架Block stage分段阶段Mile stone（里程碑，大节点）Plate-cutting下料，开工Keel-laying上船台，龙骨铺设Lauching下水mooring trial码头试验，系泊试验sea trial(sea)试航delivery of the ship交船defect list by the owner/society船东提出的消除意见清单/船级社提出的消除意见清单design stage设计阶段submit drawings to owner,classification society(LR、DNV、BV、ABS，etc)for approval向船东，船级社（劳氏，挪威，法国，美国等）提交认可图纸hull workshop船体车间machining workshop金工车间machinery engineering workshop轮机车间electrical workshop电气车间business dept.经营处perchasing dept.供应处Q.C.Dept.检验处Design dept.设计室Painting and carpenter’s workshop漆木车间Project manager项目经理Director指导者，厂长，董事Managing director执行董事，常务董事，总经理Head首长，团长，主任Manager经理，管理人，干事Leader领导者Meeting会议Negotiation谈判Agreement协议Shipyard船厂。