最新《轮机英语学习指南》补充题)
最新《轮机英语》考证补充题（20100818）1. There are four main types of marine engines: and the marine nuclear plant.A. the diesel engine, the steam turbine and dual-fuel engineB. the diesel engine, the steam turbine and the gas turbineC. the gas-diesel engine, the gasoline engine and the diesel engineD. the gasoline engine, the diesel engine and the steam turbine注：船用发动机有四种主要类型：柴油机、汽轮机、燃气轮机和船舶核动力装置，选B。
2. In crosshead engines in good condition the cylinder oil consumption may usually be .A. bellow 0.1 g/hp. hr.B. above 10 g/hp. hr.C. below 1.0 g/hp. hr.D. zero注：十字头式柴油机在状态良好的情况下气缸耗油率低于1.0 g/hp. hr., 选C。
3. The is the power available at the output shaft of the engine and can be measured usinga torsionmeter or with a brake.A. electric powerB. shaft powerC. indicated powerD. mechanical power注：轴功率是指发动机输出轴上可获得的功率，可以使用扭矩表或刹车来测量，选B。
4. The greatest turbulence in a diesel engine cylinder is created by the .A. shape of the combustion chamberB. fuel injection spray patternC. cylinder swept volumeD. degree of penetration of the fuel oil droplets注：柴油机气缸内最大的湍流是由燃油液滴的穿透程度产生的，选D。
5. The liquid flowing in the capillary is such that the difference in _____ readings taken before the capillary and after it is related to the oil viscosity.A. pressureB. velocityC. flow rateD. temperature注：对于在毛细管内流动的液体，毛细管前后测取的压差与油的粘度有关，选A。
6. The starting air bottle should be pumped up to maximum pressure by the _____ before start of the engine.A. air compressorB. refrigeration compressorC. vacuum pumpD. purifier注：在发动机启动前，应使用空压机将启动空气瓶打到最大压力，选A。
7. The primary task of the compressed air system is to deliver the starting air necessary for _____.A. starting the M.E.B. starting the emergency electric alternatorC. driving the main turbineD. driving the turbocharger注：压缩空气系统的主要任务是为启动主机提供压缩空气，选A。
8. Air compressor receivers should be “blown down” at least _____.A. yearlyB. quarterlyC. monthlyD. daily注：空气瓶应每天放残，选D。
9. Starting air for auxiliary engines may be taken directly from the main reservoirs or through .A. an auxiliary reservoirB. a controlling air bottleC. an emergency air compressorD. a main air compressor注：辅机的启动空气可直接来自主空气瓶，也可来自辅空气瓶，选A。
10. The air reservoirs must have _____ fitted to prevent rupture in the event of fire.A. high pressure alarmB. fire alarmC. extinguishersD. fusible plugs注：空气瓶必须安装易熔塞，以防发生火灾时爆炸，选D。
11. Air reservoirs are designed, built and tested similarly to _____.A. boiler drumsB. hot wellsC. condensersD. evaporators注：空气瓶的设计、建造和试验类似于锅炉的锅筒，选A。
12. When the prime movers of two paralleled generators are equipped with mechanical- hydraulic governors, and are operating within their designed range, the unit with the least amount of speed droop will _____.A. pick up more of any increase in loadB. pick up less of any increase in loadC. share an equal amount of any increase in loadD. drop an equal amount of any decrease in load注：当两台并车运行的发动机的原动机装有机械液压式调速器，并在设计范围内运行，速度降小的装置将会承担更多增加的负荷，选A。
13. Which of the following devices is a common basic element with nearly all mechanical governors?A. Power pistonB. Control rackC. Weights acted on by centrifugal forceD. Isochronous droop spring注：受离心力作用的飞重是几乎所有机械式调速器共有的基本部件，选C。
14. The required amount in the change of speed necessary before a governor will make a corrective movement is known as _____.A. speed droopB. sensitivityC. stabilityD. promptness注：在调速器能做出纠正动作之前所需要的速度变化量，称为灵敏度，选B。
15. Which of the following devices is common to both mechanical and hydraulic governors?A. Direct linkage between the ball-head and fuel rack.B. A servomotor.C. A compensating device.D. Flyweights.注：对于机械和液压式调速器，飞重是共有的部件，选D。
16. On most diesel engines, the governor controls the output speed by _____.A. controlling the amount of fuel injected into the cylindersB. varying the speed of the turbochargerC. adjusting the compression ratioD. changing the timing of the fuel injection camshaft注：在大多数柴油机中，调速器是通过控制喷入气缸的燃油量来调节速度的，选A。
17. The ability of the governor to prevent fluctuations in engine speed is termed _____.A. sensitivityB. stabilityC. promptnessD. speed droop注：调速器防止发动机速度波动的能力，称为稳定性，选B。
18. Oil mist detectors are usually used on board to detect oil mist density within _____.A. the engine crankcaseB. the engine scavenge boxesC. drain tanksD. fuel tanks注：船上油雾探测器通常用于探测发动机曲轴箱内的油雾浓度，选A。
19. An auxiliary reservoir for starting auxiliary engines should be kept at _____.A. low pressure at all timesB. full pressure at all timesC. low pressure at intermittenceD. full pressure at intermittence注：用于启动辅机的辅空气瓶，在任何时候都应保持在最大压力，选B。
轮机英语考证学习指南
轮机英语考证学习指南英文回答：As a guide to studying for the marine engineering English certification exam, I would recommend a systematic approach that covers all the necessary topics and provides ample practice opportunities. Here is a suggested study plan:Firstly, it is important to familiarize yourself with the exam format and requirements. Understand the different sections of the exam, such as reading comprehension, listening, grammar, and vocabulary. This will give you a clear idea of what to expect and how to prepare.Next, focus on improving your reading comprehension skills. Read a variety of texts related to marine engineering, such as technical manuals, articles, and industry publications. Pay attention to the main ideas, supporting details, and vocabulary used in these texts.Practice summarizing and analyzing the information you read.In addition to reading, listening skills are alsocrucial for the exam. Listen to audio recordings orpodcasts on marine engineering topics. Take notes while listening and try to understand the main points and details. This will help you improve your listening comprehension and prepare for the listening section of the exam.Grammar and vocabulary are essential components of any language exam. Review and practice the key grammar rulesand structures that are commonly tested. Build your vocabulary by learning technical terms and industry-specific terminology. Use flashcards or online resources to memorize and review the words regularly.To further enhance your language skills, engage in speaking and writing activities. Find a study partner orjoin a language exchange program to practice speaking in English. Discuss marine engineering topics, share your opinions, and ask for feedback. For writing practice, write essays or reports on relevant subjects. Pay attention tosentence structure, coherence, and clarity of your writing.Lastly, take practice tests to assess your progress and identify areas that need improvement. Look for sample exam papers or online practice tests that simulate the actual exam conditions. Time yourself and try to complete the tasks within the given time limits. Analyze your mistakes and learn from them.In conclusion, studying for the marine engineering English certification exam requires a comprehensive approach that includes reading, listening, grammar, vocabulary, speaking, and writing practice. By following a structured study plan and regularly practicing, you can improve your language skills and increase your chances of success in the exam.中文回答：作为一本轮机英语考证学习指南，我建议采用系统的方法，涵盖所有必要的主题，并提供充分的练习机会。
《轮机英语》最新题库注解
《轮机英语》老题库注解陈黄骞编写1. 船舶在加装燃油结束后，在拆卸油管前，一般用压缩空气吹洗残留在软管内的油。
2. "发动机备车"就是使发动机准备起动。
3. 机座是发动机的基础，如无其支撑，发动机的整体，尤其是轴的对中都将无从保证。
4. 飞重通常被用在机械-液压式调速器中感受发动机的速度。
5. 直列式和V型发动机的机架上一般都有道门以提供曲轴和连杆大端轴承的维修通道。
6. 回流扫气中，温度较低的扫气空气和温度较高的废气通过相邻的气口，引起缸套材料的温差问题。
7. 十字头销变椭圆了，需要光车。
8. 联锁装置用来防止在发动机换向完成之前起动空气进入气缸。
9. 燃油和滑油在进入发动机之前，都需要经过处理。
"Both A and B"意"A和B两者都"；"neither A nor B"意"既不是A也不是B"；"either A or B"意"A、B两者之一"。
10. 有时采用滑油来冷却活塞因其漏入曲柄箱不会产生（污染）问题。
11. 通过吹入新鲜空气驱除废气的过程称为扫气。
12. 淡水用来冷却气缸和气缸头，咸（海）水用来冷却润滑油，冷却器中的淡水和空冷器中的增压空气。
13. 造成发动机运行过程中功率下降或失速，首要的可能原因是轴承过热。
14. 发动机曲轴失中可以通过测量臂距差来判断。
15. 发动机A形机架的顶部有一坚固的铸铁框架称为扫气箱。
16. 铝质活塞具有惯性小（重量轻）、热膨胀系数大的特点。
17. 回流扫气式发动机中，扫气口和排气口布置在同一侧。
18. 值班人员不能做任何影响他们对主要机械和相关设备监视职责的工作。
19. 气阀推杆间隙过小会引起排气阀过早打开、过晚关闭。
20. 气阀推杆间隙过大会引起排气阀过晚打开、过早关闭。
21. 气阀推杆间隙过大会引起排气阀过晚打开、过早关闭。
最新-轮机英语关联题题库最新整理篇(带翻译)解析 精品
Passage 1（原题库第1篇）Valve drive mechanismThe valve drive mechanism commands the inlet and exhaust valves at the required timing.第3题The valve drive mechanism consists of an inlet and exhaust cam follower (8) each suspended in a plunger of the tappet assembly (7), two tubular push rods (4) with ball joints, two nodular cast iron rocker arms (2) suspended in a rocker arm bearing bracket, two yokes (5) and a yoke guide pins. See Fig. 4-1.The tappet rollers follow the cam profiles and transfer the movements through push rods to the rocker arms.第4题The rocker arms operate the inlet and exhaust valves through yokes (5).Lubrication for the rocker arms comes from the engine's secondary oil supply manifold throughdrillings in the cylinder head and rocker arm bracket.第2题The tappet assembly receives lubricating oil via channels in the engine block from the main supply manifold. For the roller and shaft, the oil is supplied through the guiding plunger.第4题To compensate for heat expansion a clearance must exist between the rocker arm and yoke.第1题All adjustments have to be done on a cold engine only.1. According to the Passage, the best time to adjust the valve clearance is _____.A. before the engine is startedB. when the engine is runningC. after the engine has just been stoppedD. when something has gone wrong with the engine注：根据文章来看，调节阀间隙的最好时间是在发动机启动之前。
轮机英语书后新题+翻译
轮机英语书后新题翻译1．When a ship in loaded condition floats at arbitrary water line, its displacement is _______ to the relevant mass of water displaced by the ship.A. equalB. largerC. smallerD. equivalent答案A 以任意吃水漂浮在水面上的载货船舶，它的排水量等于船体置换掉的相应质量的水。
ship in loaded condition 船舶处于有负载的状况arbitrary 任意的water line (船的)吃水线,水位displacement 排水量equal to 等于，与……相等relevant mass 相应的质量displace 取代，置换2．The displacement of a ship is _______ to the total weight, all told, of the relevant loaded ship.A. largerB. equalC. smallerD. equivalent答案B 船舶的排水量等于相应装载货物船舶的总重量。
total weight 总重量all told 副词，表示总计，总共，合计，用在这里强调是载货船舶总共的质量。
3．Which one is not true?A. Two main areas of skill are involved in the construction of ship.B. There are distinct divisions in responsibilities between naval architects and marine engineers.C. Each ship will assume varying proportions according to its type.D. Ships can be divided into different categories from different perspectives.答案B 哪句话不正确？造船工程师与轮机员在职责上处于截然不同的区域。
轮机系统英语试题及答案
轮机系统英语试题及答案一、选择题（每题2分，共20分）1. What is the primary function of a marine engine?A. To generate electricityB. To propel the shipC. To provide heatingD. To cool the engine2. The term "deadweight tonnage" refers to:A. The weight of the ship without cargoB. The maximum cargo capacity of the shipC. The weight of the ship fully loadedD. The total weight of the ship including cargo3. Which of the following is NOT a type of marine fuel?A. Heavy fuel oilB. Marine diesel oilC. Liquefied natural gasD. Gasoline4. What does the abbreviation "BOP" stand for in a ship's engine room?A. Ballast On PumpB. Blow Off PressureC. Black Oil PumpD. None of the above5. The main purpose of a ship's propeller is to:A. Generate electricityB. Provide stabilityC. Change the direction of the shipD. Convert rotational motion into thrust6. What is the role of a marine boiler?A. To produce steam for propulsionB. To cool the engineC. To provide fresh waterD. To heat the ship's interior7. The term "trim" in ship terminology refers to:A. The angle of the ship's bowB. The weight distribution along the ship's lengthC. The shape of the ship's hullD. The speed of the ship8. What does "GT" stand for in ship specifications?A. Gross TonnageB. Gross TransportC. General TransportD. Global Trade9. The main difference between a diesel engine and a steam turbine is:A. The type of fuel usedB. The method of converting thermal energy into mechanical energyC. The color of the engineD. The size of the engine10. What is the purpose of a ship's bilge system?A. To clean the ship's hullB. To remove water from the ship's interiorC. To provide fresh water for the crewD. To cool the engine答案：1. B2. B3. D4. D5. D6. A7. B8. A9. B10. B二、填空题（每空1分，共10分）1. The main components of a marine engine include the__________, the __________, and the __________.2. The term "draught" refers to the __________ of the ship below the waterline.3. A ship's hull is divided into several __________ to increase its structural integrity.4. The "load line marks" on a ship indicate the __________ of the ship when loaded with cargo.5. The "freeboard" is the distance between the waterline and the __________ of the ship.6. The "safety valve" in a marine boiler is designed to__________ pressure.7. The "main engine" is the primary source of __________ fora ship.8. The "stern tube" is the part of the ship where the__________ is located.9. "Machinery space" refers to the area where the ship's__________ are located.10. The "lifeboat" is a vessel designed to __________ people in case of an emergency.答案：1. engine, boiler, turbine2. depth3. compartments4. maximum permissible draft5. deck6. relieve excessive7. propulsion8. propeller9. engines10. rescue三、简答题（每题5分，共10分）1. Explain the difference between a single-screw ship and a twin-screw ship.2. Describe the function of a ship's anchor and how it is used.答案：1. A single-screw ship is propelled by a single propeller, which is driven by the main engine. It is simpler in designand usually less expensive to build and maintain. A twin-screw ship, on the other hand, has two propellers, each driven by an engine, which can be the same or different. This configuration provides better maneuverability, redundancy in case one engine fails, and often results in higher speeds.2. A ship's anchor is a device used to secure the ship when it is not in motion, particularly in harbors or at sea when the ship needs to be stationary. The anchor is dropped to the seabed, where it digs into the bottom, providing resistance to the ship's movement. The anchor is connected to the。
轮机英语问答题答案及翻译
轮机英语问答题答案及翻译1. how long have you worked on board?I have worked on board for 10 years.1。
你多长时间在船上工作的？我在船上工作了10年。
2. which certificate do you have now?I have the second engineer’s certificate.2。
该证书你有吗？我有个工程师的证书3. what is your marital status?how many departments are there on board?I am married. There are there departments on board.3。
什么是您的婚姻状况？有多少部门在船上呢？我结婚了。
在船上有三个部门。
4. how many people are there in your family? Are you married?There are there people in my family. Yes,I am married.4。
有多少人在你的家庭吗？你结婚了吗？那里有我的家人的人。
是的，我结婚了5. how many countries have you ever been to?I have been to seven countries.5。
有多少个国家，你有没有去过？我到过7个国家。
6. when did you begin to work on board? What kind of ship have you worked on?I began to work on board in 2000.i have worked on bulk sarriers.6。
你什么时候开始在船上工作的？什么样的船你工作呢？我开始在船上工作2000.i对散装sarriers工作。
7. how many importment canals are there all over the world?Three . the pamama ,suez and kiel.7。
轮机英语最新题库第二部分
5.2 MARPOL73/78 公约5.2.1 MARPOL73/78 公约中有关含油污水的排放规则3192.If it becomes necessary to pump bilges while a vessel is in port, which of the following procedures should be followed?A. Pump only if the discharge is led to a shore tank or barge.B. Pump only during the hours of darkness.C. Pump only on the outgoing tide.D. Pump only as much as is necessary.3193.The scuppers should be plugged _____.A. only if fixed containment is not usedB. only if portable containment is not usedC. only if fixed containment drains are openD. whenever the vessel is being bunkered3194.When discharging bilge water, which criteria must be observed?A. The requirement for the oil content of bilge water discharged is 15 ppm.B. No discharge in sensitive waters.C. Any discharge in sensitive waters.D. International, national or local requirements have to be observed.3195.When bilge water is heated in a holding tank, which one of the following statements is not accurate?A. The relative high temperature facilitates primary gravity separation.B. Most of the oil and organic solvents are raised to the top layer.C. The relative high the temperature is, the top oil will be collected.D. The normal high temperature has little use on the separation of emulsified oil.3196.If an oil spill occurs on deck, you should _____.A. cover the area with foamB. cover the area with absorbent materialC. wash down immediately with a fire hoseD. wash down immediately with an oil dispersing solvent3197.Which of the following methods might favor oil emulsion in bilge water?A. Raising temperature.B. Less use of surfactantC. More use of solvent.D. Polishing device fouling prevention.3198.Which of the following methods can not remove the non-separable emulsified oil in bilge water?A. Gravity separation.B. Use of adsorbentsC. Use of flocculentsD. Use of chemical addition.3199.Which one of the following is not generally recognized as one constitute of bilge water?A. Oil leaking from tanks inside engine room.B. Engine rom cleaning water.C. Water leaking from the separator sludge tank.D. Sewage water.3200.Which of the following methods might be used as the treatment on emulsified oil?A. gravity separationB. centrifugeC. Cyclone.D. Cross-flow membrane filtration3201.Waste oil should _____.A. be treated according to the C/E’s command exactlyB. be treated according to MARPOLC. accumulate in bilges or on tank tops in accordance with MARPOLD. discharge to sea at the specified areas3202.According to Annex I of MARPOL73/78, Oily waste from cargo tanks of oil tankers can be discharged when the ship is more than ______ away from the nearest land.A. 50 nautical milesB. 30 nautical milesC. 15 nautical milesD. 12 nautical miles3203.According to Annex I of MARPOL73/78, the instantaneous discharging rate of the oily waste from cargo tanks of oil tankers must be lower than ______.A. 30 liters per nautical mileB. 15liters per nautical mileC. 30 ppmD. 15 ppm3204.According to Annex I of MARPOL73/78, the discharging oil content of the machinery space bilges must be lower than ______.A. 30 liters per nautical mileB. 15 liters per nautical mileC. 30 ppmD. 15 ppm3205.The third engineer took the _____ and checked the tank table in the office and recorded all relevant data, as well as calculated the bunkering.A. water levelB. sump levelC. ballast tank levelD. ship’s trim3206.Which of the following should be recorded in Oil Record Book Part I (machinery ______ space operation)?A. Non automatic discharge overboard of machinery space bilge water.B. Automatic discharge overboard of machinery space bilge water.C. A and B.D. Neither A nor B3207.Which of the following is NOT on the list items to be recorded in Oil Record Book Part I (machinery space operation)?A. Accidental discharge of oil.B. Disposal of oil residues.C. Quantify of water produced by F.W.G.D. Discharge of dirty ballast or cleaning water from fuel oil tanks.3208.Which of the following operations need NOT to be entered on the Oil Record Book Part I?(1) Routine discharge at sea of bilge water containing oil from the machinery spaces through strainers;(2) Bunkering of fuel oil.A. (1) only.B. (2) only.C. Both (1) and (2).D. Neither (1) and (2).Which of the following operations need NOT to be entered on the Oil Record Book Part I?(1)Disposal of oil residues;(2)Internal transfer of fuel oil.A. (1) onlyB. (2) onlyC. Both (1) and (2)D. Neither (1) and (2)3210.Which of the following operations need to be entered on the Oil Record Book Part I?(1)Ballast. of fuel oil, tanks;(2) Condition of oil discharge monitoring and control system.A. (1) only.B. (2) only.C. Both (1) and (2).D. Neither (1) and (2)3211.The bilge main is arranged to drain any watertight compartment _____ ballast, oil or water tanks and to discharge the contents overboard.A. more thanB. other thanC. in addition toD. except for3212.Oil Record Book Part I shall be provided to every oil tanker of 150 tons gross tonnage and above and every ship of 400 tons gross tonnage and above, _____ oil tankers, to record relevant machinery space operations.A. as well asB. as long asC. rather thanD. other than3213.Oil Record Book Part I shall be provided to ______.A. every oil tanker.B. every ship of 400 tons gross tonnage and above.C. A and B.D. Neither A nor B.3214.While loading bunkers, you notice oil on the water near the vessel. What should you do firstA. Stop loadingB. Notify the harbour administrationC. Determine if the vessel is the source of the pollutionD. Start the main engine and put them in gear to disperse the spill3215.Oil Record Book Part I shall be provided to every oil tanker of 150 tons gross tonnage and above and every ship of 400 tons gross tonnage and above, ______ oil tankers, to record relevant machinery space operations.A. as well asB. as 10ng asC. rather thanD. other than3216.An oil in water monitor is required in order to measure ______.A. the oil content in waterB. the water content in fuel oilC. the water level in bilge wellD. the oil level in bilge well3217.A vessel is required to carry an Oil Record Book Part I to log entries in the book regarding the ____.A. discharge of ballast or cleaning water from fuel tanksB. sounding levels of all fuel tanks on a daily basisC. grade and specific gravity of all fuel oil carriedD. fuel consumption rates on a weekly basis3218.A segregated ballast system is a system where _____.A. all ballast is processed through the oily water separatorB. ballast is taken on and discharged through a separate main deck riserC. ballast and cargo tanks are separated by cofferdamsD. all ballast lines, tanks, and pumps are independent of those used for oil3219.Which of the following machinery space operations is required to be logged in the Oil Record Book?A. Ballasting or cleaning of fuel oil tanks.B. Shifting suction of main fuel pump to reserve fuel oil tank.C. Changing out sprayer plates to adjust for steam demand.D. Daily inspection of engine room bilges.3220.Which of the following operations aboard a tanker must be recorded in the Oil Record Book _____.A. Any internal transfer of oil cargo during a voyageB. The discharge overboard in port or at sea of any bilge water accumulated in machinery spacesC. The loading or unloading of any or all oil cargoD. All of the above.3221.Under the regulations implementing MARPOL, a mobile offshore drilling unit is required to have an International Oil Pollution Prevention (IOPP) certificate when the unit ______.A. is drilling on the Outer Continental ShelfB. moves to a new Outer Continental ShelfC. engages in a voyage to a port of another country which is a party of MARPOLD. All of the above.3222.In the event of a small bunker oil spill on deck occurring while bunkering, you should _____.A. wash down the area immediately with a fire hoseB. wash down the area with keroseneC. cover the area with absorbent materialD. cover the area foam3223.Small oil spills on deck can be prevented from contaminating any waters by _____.A. plugging all scuppers and drainsB. placing floating booms around the shipC. regularly emptying all drip pansD. thoroughly draining all bunkering hoses3224.The use of sinking and dispersing agents for the removal of surface oil is ______.A. the most common method used in the United StatesB. too expensive for common useC. generally safe to sea lifeD. generally harmful to sea life3225.The sections of an Oil Record Book proceeding the log pages contain a ______.A. damage control plan for isolating fire main valvesB. list of machinery space operation itemsC. complete classification of hazardous materialsD. detailed listing of all organizations to call in the event of an accidental oil spill3226.The term “discharge”, as it applies to the pollution regulations, means _____.A. spillingB. leakingC. dumpingD. All of the above.3227.Waste oil from the lube oil sumps of machinery may NOT be _____.A. drained into the vessel’s bilgesB. reclaimed for other usesC. held in a slop tankD. purified and then reused3228.Bilges may be pumped _____.A. on the outgoing tideB. overboard after tideC. overboard through an oily water separatorD. anytime in an emergency, i.e. main engine lube oil failure3229.A new ocean going ship of 2000 gross tons having an inoperative oily water separator may dispose of its bilge slops by _____.A. holding its slops onboard until they can be pumped into the city sewer systemB. circulating them through the lube oil purifier to remove water and debrisC. holding its slops onboard until they can be discharged to a shore side reception facilityD. pumping them into a settling tank for separation before pumping the oily water residue overboard3230.An oceangoing ship of 400 gross tons and above must be fitted with a standard discharge shore connection. What is the size of the bolt circle diameter of the shore connection required to transfer oily ballast to a shore si’de reception facility?A. 125 mm.B. 183 mm.C. 215 mm.D. It depends on outside pipe diameter3231.The term “oil”, as used in the Pollution Prevention Regulations, ______.A. fuel oil onlyB. crude oil onlyC. liquefied petroleum gasD. petroleum oil of any kind3232.The term “oily mixture”, as defined in the Pollution Prevention Regulations includes _____.A. sludgeB. oily ballast waterC. bilge slopsD. All of the above.3233.Which of the following liquids can ordinarily be discharged overboard without being processed through an oily water separator?A. Cargo tank ballast.B. Segregated ballast.C. Engine room bilges.D. Cargo pump room bilges.3234.The term “oil”, as used in the Pollution Prevention Regulations, ______.A. fuel oil onlyB. crude oil onlyC. liquefied petroleum gasD. petroleum oil of any kind3235.The term “oily mixture”, as defined in the Pollution Prevention Regulations includes ______.A. sludgeB. oily ballast waterC. bilge slopsD. All of the above.3236.Which of the following liquids can ordinarily be discharged overboard without being processed through an oily water separator?A. Cargo tank ballast.B. Segregated ballast.C. Engine room bilges.D. Cargo pump room bilges.3237.The word “discharge” as used in Pollution Prevention Regulations applies to oil _____.A. leaked into navigable watersB. poured into navigable watersC. pumped into navigable waters through a fixed piping systemD. All of the above.3238.The pollution prevention regulations do not apply to the transfer or discharge of _____.A. bunker fuel for use aboard shipB. lubricating oil for use aboard shipC. coconut oil carried in tank vesselsD. oily water from a ship’s bilges3239.The pollution prevention regulations state that slop oil and sludge that result as part of normal fueling operations should be disposed of by _____.A. discharging ashore into the sewer systemB. sealing in disposable plastic barrels aboard shipC. discharging into a shore tank or slop bargeD. dumping into the ship’s bunker tanks3240.What type of oil is not covered in the oil pollution laws?A. Mineral oil.B. Machinery oil being transferred for shipboard use.C. Crude oil unrefined.D. Normal bilge oil and water.3241.What is used for preventing pollution damage to the sea from ships?A. MARPOL73/78.B. SOLAS74.C. STCW78/95.D. ISPS 2002.3242.The oil discharge monitoring system in the oil tanker vessels is used for detecting the amount of oil discharged overboard to ensure that it does not exceed _____.A. 15 liters/nautical mileB. 30 liters/nautical mileC. 60 liters/nautical mileD. 100 liters/nautical mile3243.To receive oil residues from the purification of fuel and lubricating oils in the machinery spaces, what kind of tank(s) should be provided on board?A. Bilge tank.B. Sludge tank.C. Overflow tank.D. Oil collecting tank.5.2.2 有关国家、港口的防污染规则3244.Under MARPOL Code, the ship to which it applies has to carry _____.A. an International Ship Security CertificateB. an International Oil Pollution Prevention CertificateC. a Safety Management CertificateD. an International Ballast Water Management Certificate3245.Disposal of all kinds of garbage but _____ is prohibited within Special Areas.A. plasticsB. comminuted or ground papers, rags, glass, metal etc.C. food waste comminuted or groundD. incinerator ash3246.According to the international regulations concerning the prevention of pollution of sea areas from ships, the disposal into the sea of all plastics is _____.A. welcomeB. admitted in some special sea areasC. prohibitedD. acceptable3247.The Pollution Prevention Regulations require that all oil spills in United States water be reported immediately to the _____.A. local port authorityB. Corps of EngineersC. U.S. Coast GuardD. state pollution board3248.When the garbage is mixed with some discharges having different disposal or discharge requirements, ______ shall apply.A. any requirement appointed by the PSC officerB. the most suitable requirementC. the most stringent requirementD. no requirement3249.The MARPOL Convention is the main international convention _____.A. about marine pollution preventionB. covering marine protection of lifeC. about marineD. about ship and port security3250.According to Annex IV of MARPOL73/78, the comminuted and disinfected sewage using an approved system can be discharged when the ship is more than _____ away from the nearest land.A. 30n mileB. 5n mileC. 12n mileD. 25n mile3251.According to Annex V of MARPOL73/78, the dunnage, lining and packing materials which will float can be discharged when the ship is more than ______ away from the nearest land.A. 3n mileB. 5n mileC. 12n mileD. 25n mile3252.The sludge tank installed in the diesel engine room is used to collect _____.(1)sludge from the fuel oil settling tanks ad centrifuge;(2)water that has been collected in the settling tank.A. (1) only.B. (2) only.C. Both(1) and (2).D. Neither (1) or (2)3253.The latest annex of MARPOL73/78 is about _____.A. the Prevention of Pollution by OilB. the Prevention of Pollution by Noxious Liquid Substances in BulkC. Prevention of Pollution by Garbage from ShipsD. Prevention of Air Pollution from Ships3254.Where tanks are arranged for either oil or ballast _____ must be fitted in the pipe so that only the ballast main or the oil transfer main connected to the tank.A. a sea water chestB. a change-over chestC. a buffer tankD. a three-way valve3255.A shipboard oil pollution emergency plan is required of _____.A. all vessels, regardless of size and commercial applicationB. any barge or other ship which is constructed or operated in such a manner that no oil in any form can be carried aboardC. an oil tanker of 150 gross tons or above, or other ship of 400 gross tons or aboveD. an oil tanker of 400 tons and above, or other ships of 150 gross tons and above3256.Records of garbage disposal are required to be maintained ______.A. until each quadrennial PSC inspectionB. until the end of each voyageC. for a minimum of one yearD. for a minimum of two years3257.Which statement regarding garbage disposal is correct?A. Records for ground garbage disposal are not required when disposal into the sea occurs more than 25 miles offshore.B. Discharging or transfer of garbage while in port to a shore facility must be recorded.C. Maintaining records for the incineration of garbage aboard ship is not required.D. The recording of garbage disposal should include the approximate weight.3258.When off loading garbage to another ship, your records must identify that ship by name and ____.A. home portB. operator’s name of recordC. official numberD. waster’s name3259.A vessel sailing through the specific special areas may discharge or dispose of _____.A. incinerated ash at anytimeB. fairly dense material that will sink, i.e. metal cans or glass bottles at anytimeC. victual waste when at least 12 nautical miles from shoreD. absolutely no garbage at anytime3260.A person on a fixed, or floating platform engaged in oil exploration, located 10 nautical miles from nearest land MAY discharge _____.A. food wasteB. food, ground to less than 1C. paper, ground to less than1D. None of the above.3261.A new four-category categorization system for noxious and liquid substances, ______ is Noxious Liquid Substances which, if discharged into the sea from tank cleaning or deballasting operations, are deemed to present a major hazard to either marine resources or human health and, therefore, justify the prohibition of the discharge into the marine environment.A. Category XB. Category YC. Category ZD. Other Substances3262.A new four-category categorization system for noxious and liquid substances, _____ is Noxious Liquid Substances which, if discharged into the sea from tank cleaning or deballasting operations, are deemed to present a hazard to either marine resources or human health and therefore justify a limitation on the quality and quantity of the discharge into the marine environment.A. Category XB. Category YC. Category ZD. Other Substances3263.A new four-category categorization system for noxious and liquid substances, _____ is Noxious Liquid Substances which, if discharged into the sea from tank cleaning or deballasting operations, are deemed to present a minor hazard to either marine resources or human health and therefore justify less stringent restrictions on the quality and quantity of the discharge into the marine environment.A. Category XB. Category YC. Category ZD. Other Substances3264.A new four-category categorization system for noxious and liquid substances, _____ is Substances which have been evaluated and found to fall outside Category X, Y or Z because they are considered to present no harm to marine resources, human health, amenities or other legitimate uses of the sea when discharged into the sea from tank cleaning of deballasting operations.A. Category XB. Category YC. Category ZD. Other Substances3265.Annex I of MARPOL73/78 contains regulations for the prevention of _____.A. pollution by oilB. pollution by noxious liquid substances carried in bulkC. pollution by sewage from shipsD. pollution by garbage from ships3266.Annex V of MARPOL73/78 contains regulations for the control of ______.A. pollution by oilB. pollution by noxious liquid substances in bulkC. pollution by sewage from shipsD. pollution by garbage from ships3267.Annex III of MARPOL73/78 contains regulations for the prevention of _____.A. pollution by oilB. pollution by noxious liquid substances carried in bulkC. pollution by harmful substances carried by sea in packaged formD. pollution by sewage from ships3268.Annex V of MARPOL73/78 contains regulations for the prevention of _____.A. pollution by oilB. pollution by noxious liquid substances carried in bulkC. pollution by sewage from shipsD. pollution by garbage from ships3269.Annex VI of MARPOL73/78 contains regulations for the prevention of _____.A. air pollution from shipsB. pollution by noxious liquid substances carried in bulkC. pollution by harmful substances carried by sea in packaged formD. pollution by sewage from ships3270.MARPOL73/78 consists of six separate annexes, which of the following annexes must be accept by States Parties?A. Annex I and III.B. Annex I and II.C. Annex I and VI.D. Annex I and V.3271.MARPOL73/78 consists of six separate annexes, which of the following annexes are voluntary?A. Annex I, III and IV.B. Annex II, III, IV, and V.C. Annex III, IV, V and VI.D. Annex I, III, V and VI.3272.A person on a fixed or floating platform engaged in oil exploration MAY discharge food waste into the sea when the distance from the nearest land is at least _____.A. 3 nautical milesB. 5 nautical milesC. 12 nautical milesD. 25 nautical miles3273.Which of the circumstances listed is an exception to the garbage discharge requirements in Annex V to MARPOL73/78?A. The garbage to be discharged will sink.B. Garbage accumulation onboard has exceeded storage space.C. A person falls overboard, and a plastic ice chest is thrown for flotation.D. The destination port or terminal cannot receive garbage.3274.According to the international regulations concerning the prevention of pollution of sea areas from ships, the disposal IMO the sea of all plastics is _____.A. welcomeB. admitted in some special sea areasC. prohibitedD. acceptable3275.Annex IV of MARPOL73/78 contains regulations for the prevention of ______.A. pollution by oilB. pollution by noxious liquid substances carried in bulkC. pollution by sewage from shipsD. pollution by garbage from ships3276.Ships do not permitted to the TBT paint after 2008. It ism required by ______.A. the International Convention for the Safety of the Life at SeaB. the International convention for the Prevention from shipsC. the International Convention on control of harmful anti-fouling systems on shipsD. the International Convention for the Control and Management of Ship’s Ballast Water and Sediments3277.Engine parameters shall be corresponded to NOx Technical Files. This is required by _____.A. MARPOL Annex IIIB. MARPOL Annex VIC. MARPOL Annex VD. MARPOL Annex VI3278.When a ship is involved in an oil pollution incident in China, the ship must report without delay to _____.A. China Maritime AdministrationB. the companyC. the cargo ownerD. ship owner3279.The Master should call _____ for permission to use chemical agents in response to oil pollution into the sea.A. the flag stateB. the coastal stateC. the port stateD. the shipping company3280.It is necessary for the ship to contact ______ for authorization prior to undertaking mitigating actions in an oil pollution incident.A. the port stateB. the shipping companyC. the coastal stateD. the flag state3281.The Garbage Record Book, as a part of the ship’s official logbook, shall be kept on board and preserved for a period of _____.A. 3 years after making the first entryB. 2 years after the last entryC. 3 months after last entryD. 3 years after the last entry3282.The International Sewage Pollution Prevention Certificate shall be issued for a period specified by the Administration, which shall not exceed _____ from the date of issure.A. six monthsB. one yearC. three yearsD. five years3283.Crude oil washing of cargo tanks has the following advantages except for ______.A. reducing the erosion of the cargo tanksB. increasing the total quantity of oil to carryC. reducing the quantity of water contained in oilD. reducing cargo discharged time3284.Which of the following equipment is not pollution prevention equipment?A. Oily water separator.B. Sewage treatment plant.C. Fuel oil separator.D. Incinerator.。
《轮机英语》题库新题目练习
《轮机英语》题库新题目练习2251.The data to be recorded on this sheet _____ the performance of the engine.A. makes the experts to judgeB. enables the experts to judgeC. make the experts judgingD. enable the experts to judge此表所记录的数据能够使专家判断出发动机的操作性能2252.Cooling _____ the engine metals retain their mechanical properties.A. forcesB. enablesC. makesD. is able to冷却使发动机保持机械性能。
2253. _____ that everything in the engine crankcase is correct, start up the crankcase lubricating oil pumpA. To satisfyB. To be satisfiedC. After satisfyingD. After being satisfied确定发动机曲轴箱一切正常后，启动润滑油汞。
2254、Hearing a strong noise, _____ at once.A . the engine stoppedB. the engine was stoppedC. he stopped the engineD. he had stopped the engine引擎发出巨大响声后，应迅速关闭发动机。
2255. The two-stroke cycle begins with the piston coming up from the BDC, with the scavenging ports in the sides of the cylinders being _____.A. openB. uncoverC. coveredD. closed活塞从BDC中开启后二行程循环开始，同时汽缸边上排除废气的气门也随之打开。
轮机英语8套（6）
轮机英语8套（6）1、T eam members share accurate understanding of current and predicted engine-room and associated systems state, and of .A. external environmentB.external resourcesC.internal environmentD.internal resources2、Which of the equipment listed is most effective in processing bilge slops for overboard discharge? (172917:第2 章船舶辅助机械:748) 查看备注查看答案A. A 100PPM oily water separator. B. the second engineerC. the third engineerD. the fourth engineer6、Under ISPS Code, the ship to which it applies has to carry _. (174865:第5 章国际公约、规则:235) 查看备注查看答案A. an International Ship Security CertificateB. an International O i l Pollution Prevention CertificateC. a Safety Management CertificateD. an International Ballast Water Management Certificate7、In order to protect the aerobic bacteria from death, the sewage plant should workB. Assembling the lube oil purifier as a separator and aligning it to the bilge overboard. .C. A 15PPM oily water separatorD. A magnetic duplex strainer3、During the PSC inspection, under the provisions of SOLAS74, which one may not be regarded as clear grounds for ships detainment? (174599:第4 章船舶轮机管理业务:621) 查看备注查看答案A. Excess amount of oily-water mixtures in bilgesB. Insulation of piping including exhaust pipes in engine room contaminated by oilC. Improper operation of bilge pumping arrangementsD. Paint peeling off the uptake4、A gearbox is used in a ship driven by a medium-speed diesel engineA.to govern the engine speedB.to increase the engine speedC.to reduce the engine speedD.to fix the propeller shaft5、Usually _ handles the majority of the correspondence and negotiation needed during transactions of stores and spare parts in the engine department. (174448:第4 章船舶轮机管理业务:470) 查看备注查看答案A. the chief engineer A.at 3-month intervalsB.at 14-day intervalsC.at 7-day intervalsD.continuously8、After charging solid waste, close the dump chute, and ignite it with the _.A.auxiliary and waste oil burnersB.auxiliary burner or the waste oil burnerC.auxiliary burnerD.waste oil burner9、The separating effect of oil separator is not very good, the reason may be _ 。
《英语学习指南》
《英语学习指南》编辑：理想谭一、英语学习技巧1. 多听多说- 技巧阐述：多听英语广播、电影、音乐等，模仿标准的发音和语调。
勇敢地开口说英语，不要害怕犯错。
- 示例：每天听30 分钟英语广播，如BBC 英语。
参加英语角，与其他学习者交流。
2. 阅读英文书籍和文章- 技巧阐述：从简单的英语读物开始，逐渐提高难度。
阅读时注意积累词汇和表达方式。
- 示例：先读《小王子》英文版，再挑战《哈利·波特》系列。
3. 写作练习- 技巧阐述：坚持写英语日记、短文等，提高写作能力。
可以请老师或英语水平高的人帮忙批改。
- 示例：每周写一篇英语日记，记录自己的生活和感受。
4. 学习语法- 技巧阐述：系统地学习英语语法，掌握句子结构和词法规则。
通过例句和练习加深理解。
- 示例：使用语法书，结合在线课程学习。
5. 利用学习工具- 技巧阐述：借助英语学习软件、词典、在线课程等资源，提高学习效率。
- 示例：使用百词斩背单词，用英语流利说练习口语。
二、英语语法要点1. 一般现在时- 用法：表示经常发生的动作、存在的状态或习惯性的行为。
- 结构：主语+ 动词原形（第三人称单数加-s/-es）。
- 例句：I go to school every day.（我每天去上学。
）He likes playing basketball.（他喜欢打篮球。
）2. 一般过去时- 用法：表示过去某个时间发生的动作或存在的状态。
- 结构：主语+ 动词的过去式。
- 例句：I went to the park yesterday.（我昨天去了公园。
）She was happy last week.（她上周很开心。
）3. 一般将来时- 用法：表示将来要发生的动作或存在的状态。
- 结构：主语+ will/shall + 动词原形；主语+ be going to + 动词原形。
- 例句：I will go to Beijing next week.（我下周将去北京。