744822120;中文规格书,Datasheet资料

744732471;中文规格书,Datasheet资料

2.0 1.02012-08-272010-03-15SStCZCZWürth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyTel. +49 (0) 79 42 945 - 0A Dimensions: [mm]C Schematic:F Typical Inductance vs. Current Characteristics:H4: Classification Wave Soldering Profile:H5: Classification Wave ProfileProfile FeaturePreheat- Temperature Min (T smin )- Temperature Typical (T stypical ) - Temperature Max (T smax ) - Time (t s ) from (T smin to T smax )Δ preheat to max Temperature Peak temperature (T p )Time of actual peak temperature (t p )Ramp-down rate - Min - Typical - MaxTime 25°C to 25°C Pb-Free Assembly 100°C 120°C 130°C 70 seconds 150°C max.250°C - 260°C max. 10 secondsmax. 5 second each wave ~ 2 K/s ~ 3.5 K/s ~ 5 K/s 4 minutesSn-Pb Assembly 100°C 120°C 130°C 70 seconds 150°C max.235°C - 260°C max. 10 secondsmax. 5 second each wave ~ 2 K/s ~ 3.5 K/s ~ 5 K/s 4 minutesrefer to EN 61760-1:2006H Soldering Specifications:I Cautions and Warnings:The following conditions apply to all goods within the product series of WE-TISof Würth Elektronik eiSos GmbH & Co. KG:General:All recommendations according to the general technical specifications of the data-sheet have to be complied with.The disposal and operation of the product within ambient conditions which probably alloy or harm the wire isolation has to be avoided.If the product is potted in customer applications, the potting material might shrink during and after hardening. Accordingly to this the product is exposed to the pressure of the potting material with the effect that the core, wire and termination is possibly damaged by this pressure and so the electrical as well as the mechanical characteristics are endanger to be affected. After the potting material is cured, the core, wire and termination of the product have to be checked if any reduced electrical or mechanical functions or destructions have occurred.The responsibility for the applicability of customer specific products and use in a particular customer design is always within the authority of the customer. All technical specifications for standard products do also apply for customer specific products.Washing varnish agent that is used during the production to clean the application might damage or change the characteristics of the wire in-sulation, the marking or the plating. The washing varnish agent could have a negative effect on the long turn function of the product.Direct mechanical impact to the product shall be prevented as the ferrite material of the core could flake or in the worst case it could break. Product specific:Follow all instructions mentioned in the datasheet, especially:•The solder profile has to be complied with according to the technical wave soldering specification, otherwise no warranty will be sustai-ned.•All products are supposed to be used before the end of the period of 12 months based on the product date-code, if not a 100% solderabi-lity can´t be warranted.•Violation of the technical product specifications such as exceeding the nominal rated current will result in the loss of warranty.•Due to heavy weight of the components of size 1014, strong forces and high accelerations might have the effect to damage the electrical connection or to harm the circuit board and will result in the loss of warranty.1. General Customer ResponsibilitySome goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the are-as, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The responsibi-lity for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not.2. Customer Responsibility related to Specific, in particular Safety-Relevant ApplicationsIt has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime can-not be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications.In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component.3. Best Care and AttentionAny product-specific notes, warnings and cautions must be strictly observed.4. Customer Support for Product SpecificationsSome products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve spe-cific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter.5. Product R&DDue to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the customer as per Secti-on 1 and 2 remains unaffected.6. Product Life CycleDue to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a stan-dard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability ex-pectancy before or when the product for application design-in disposal is considered.The approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.7. Property RightsAll the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth Elektronik eiSos GmbH & Co. KG.8. General Terms and ConditionsUnless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth Elektronik eiSos Group”, last version available at .J Important Notes:The following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG:分销商库存信息: WURTH-ELECTRONICS 744732471。

74477620;中文规格书,Datasheet资料

description := Start of winding Marking = Inductance code33% Umgebungstemperatur / temperature:+20°CFerritMST 04-10-11NameDatum / date.............................................................................................................................................................................................................................................Würth ElektronikHP 4274 A für/for L und/and Q HP 34401 A für/for R DC und I DCD Prüfgeräte / test equipment:POWER-CHOKE WE-PD2Würth Elektronik eiSos GmbH & Co.KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked Basismaterial / base material: Datum / date.........................................................................Unterschrift / signature Kontrolliert / approvedIt is recommended that the temperature of the part does not exceed 125°C under worst case operating conditionsF Werkstoffe & Zulassungen / material & approvals:Endoberfläche / finishing electrode:Draht / wire:Sn/Cu - 99,3/0,7%2UEWF 155°CUmgebungstemp. / ambient temperature: -40°C - + 85°C Kunde / customerFreigabe erteilt / general release:E Testbedingungen / test conditions:Betriebstemp. / operating temperature: -40°C - + 125°C Luftfeuchtigkeit / humidity:G Eigenschaften / general specifications:Änderung / modificationVersion 1description :MST 04-10-11NameDatum / datePOWER-CHOKE WE-PD2DATUM / DATE : 2004-10-11H Induktivitätskurve / Inductance curve:Freigabe erteilt / general release:Kunde / customer...........................................................................................................................................................Datum / dateUnterschrift / signature Würth ElektronikWürth Elektronik eiSos GmbH & Co.KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400...........................................................................................................................................................Geprüft / checked Kontrolliert / approvedÄnderung / modificationVersion 1Bezeichnung :description :a 330,0± 0,5mmb 20,20± 0,5mm+ 0,5- 1,0d100,0± 0,5mmMST 04-10-11NameDatum / dateArtikelnummer / part number :74477620SPEICHERDROSSEL WE-PD2POWER-CHOKE WE-PD2Freigabe erteilt / general release:Kunde / customermm 13,00c ...........................................................................................................................................................Datum / dateUnterschrift / signature Würth Elektronik...........................................................................................................................................................Würth Elektronik eiSos GmbH & Co.KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked Kontrolliert / approvedRollenspezifikation / Reel specification:Änderung / modificationVersion 1The force for tearing off cover tape is20 to 70 grams in arrow directionfeeding directionThis electronic component is designed and developed with the intention for use in general electronics equipments. Before incorporating the components into any equipments in the field such as aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc. where higher safety and reliability are especially required or if there is possibility of direct damage or injury to human body. In addition, even electronic component in general electronic equipments, when used in electrical circuits that require high safety, reliability functions or performance, the sufficient reliability evaluation-check for the safety must be performed before use. It is essential to give consideration when to install a protective circuit at the design stageRoHS compliantLF分销商库存信息: WURTH-ELECTRONICS 74477620。

744325650;中文规格书,Datasheet资料

Bezeichnung :description :A mmB mmC mmD mmE mmF mmG mmMarking = part numberEigenschaften / properties Wert / valueEinheit / unittol.Lerrlaufinduktivität/initial inductance Nenn-Induktivität /rated inductance DC-Widerstand /DC-resistance Nennstrom /rated current Sättigungsstrom/saturation current Eigenres.-Frequenz self-res.-frequency33%Umgebungstemperatur / temperature:+20°CWE-Superflux BD 11-01-11NameDatum / dateÄnderung / modificationVersion 1typ.typ.1,9± 0,54,7± 0,310,2± 0,510,5± 1,0 D Prüfgeräte / test equipment :HP 34401 A & Fluke 54II für/for I DC; Luftfeuchtigkeit / humidity:WAYNE KERR 3260B für/for L 0; I SAT 4,0± 0,53,0± 1,0± 20%5,1± 0,45 A Mechanische Abmessungen / dimensions :100 kHz / 10mA L 06,50µH B Elektrische Eigenschaften / electrical properties :C Lötpad / soldering spec.:max.12,50SPEICHERDROSSEL WE-HCI POWER-CHOKE WE-HCIWürth Elektronik eiSos GmbH & Co. KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked .................................................................................................DATUM / DATE : 2011-01-11± 10%A Testbedingungen / test conditions AIEIW-200Basismaterial / base material:Umgebungstemp. / ambient temperature: -40°C - +100°C F Werkstoffe & Zulassungen / material & approvals :G Eigenschaften / general specifications :Kontrolliert / approvedD T= 50 K A 10,0I N D L/L 0= 30 %8,4Metra HIT 27I für/for R DCI sat SRF27E Testbedingungen / test conditions :Würth Elektronik...............................................................................Arbeitstemperatur / operating temperature: -40°C - +150°C Freigabe erteilt / general release:Kunde / customerDraht / wire: blackcoating:not exceed 150°C under worst case operating conditions.http://www.we-online.deDatum / date.........................................................................Unterschrift / signature MHz100 kHz / 10mA / 8,4AL N 5,00@ 20° C R DC µH m W It is recommended that the temperature of the part does typ.[mm]3,83,854,0EA M a r k i n gCDBFGRDC is measured at these pointsBezeichnung :description :BD 11-01-11NameDatum / dateSPEICHERDROSSEL WE-HCI POWER-CHOKE WE-HCIDATUM / DATE : 2011-01-11........................................................................................................................................................Freigabe erteilt / general release:Kunde / customer..............................................................................................................................................Version 1Datum / dateUnterschrift / signature Würth ElektronikD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400http://www.we-online.deGeprüft / checked Kontrolliert / approvedÄnderung / modification0,001,002,003,004,005,006,007,00246810121416L (µH )Current (A)Induktivität vs Strom (typ.)Inductance vs Current (typ.)Bezeichnung :description :BD 11-01-11NameDatum / dateVersion 1Freigabe erteilt / general release:Kunde / customerGeprüft / checked Kontrolliert / approvedÄnderung / modification........................................................................................................................................................Datum / dateUnterschrift / signature Würth Elektronik..............................................................................................................................................http://www.we-online.deD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 4000,0010,0020,0030,0040,0050,0060,0070,0080,0090,00100,0002468101214T [ °C ]Current (A)Temperaturanstieg vs. Strom (typ.)/ Temperature rise vs. Current (typ.)Bezeichnung :description :I Rollenspezifikation / tape and reel specification :A 11,3± 0,1mm B16,0± 0,1mm + 0,1- 0,0+ 0,05- 0,05E 4,00± 0,1mmF 2,00± 0,1mmG 1,75± 0,1mmH 11,5± 0,1mmI 10,8± 0,1mmJ 5,40± 0,1mm T 0,35± 0,05mm W24,0± 0,3mma 330,00± 2,0mmb 24,5± 0,8mmc 29,50± 0,5mmd 100,0± 1,5mmBD 11-01-11NameDatum / datemm SPEICHERDROSSEL WE-HCI POWER-CHOKE WE-HCIDATUM / DATE : 2011-01-11........................................................................................................................................................Freigabe erteilt / general release:Kunde / customerVersion 1Datum / dateUnterschrift / signature Würth ElektronikD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked Kontrolliert / approvedÄnderung / modificationWürth Elektronik eiSos GmbH & Co. KG................................................................................................................................................Rollenspezifikation / Reel specification:D 1,55mm Gurtspezifikation / Tape specification:C 1,50Ø cabWEFGA B CØ DHITJ150feeding directionThis electronic component has been designed and developed for usage in general electronic equipment. Before incorporating this component into any equipment where higher safety and reliability is especially required or if there is the possibility of direct damage or injury to human body, for example in the range of aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc, Würth Elektronik eiSos GmbH must be informed before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.dcb分销商库存信息: WURTH-ELECTRONICS 744325650。

744732681;中文规格书,Datasheet资料

2.0 1.02012-08-272010-03-15SStCZCZWürth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyTel. +49 (0) 79 42 945 - 0A Dimensions: [mm]C Schematic:F Typical Inductance vs. Current Characteristics:H4: Classification Wave Soldering Profile:H5: Classification Wave ProfileProfile FeaturePreheat- Temperature Min (T smin )- Temperature Typical (T stypical ) - Temperature Max (T smax ) - Time (t s ) from (T smin to T smax )Δ preheat to max Temperature Peak temperature (T p )Time of actual peak temperature (t p )Ramp-down rate - Min - Typical - MaxTime 25°C to 25°C Pb-Free Assembly 100°C 120°C 130°C 70 seconds 150°C max.250°C - 260°C max. 10 secondsmax. 5 second each wave ~ 2 K/s ~ 3.5 K/s ~ 5 K/s 4 minutesSn-Pb Assembly 100°C 120°C 130°C 70 seconds 150°C max.235°C - 260°C max. 10 secondsmax. 5 second each wave ~ 2 K/s ~ 3.5 K/s ~ 5 K/s 4 minutesrefer to EN 61760-1:2006H Soldering Specifications:I Cautions and Warnings:The following conditions apply to all goods within the product series of WE-TISof Würth Elektronik eiSos GmbH & Co. KG:General:All recommendations according to the general technical specifications of the data-sheet have to be complied with.The disposal and operation of the product within ambient conditions which probably alloy or harm the wire isolation has to be avoided.If the product is potted in customer applications, the potting material might shrink during and after hardening. Accordingly to this the product is exposed to the pressure of the potting material with the effect that the core, wire and termination is possibly damaged by this pressure and so the electrical as well as the mechanical characteristics are endanger to be affected. After the potting material is cured, the core, wire and termination of the product have to be checked if any reduced electrical or mechanical functions or destructions have occurred.The responsibility for the applicability of customer specific products and use in a particular customer design is always within the authority of the customer. All technical specifications for standard products do also apply for customer specific products.Washing varnish agent that is used during the production to clean the application might damage or change the characteristics of the wire in-sulation, the marking or the plating. The washing varnish agent could have a negative effect on the long turn function of the product.Direct mechanical impact to the product shall be prevented as the ferrite material of the core could flake or in the worst case it could break. Product specific:Follow all instructions mentioned in the datasheet, especially:•The solder profile has to be complied with according to the technical wave soldering specification, otherwise no warranty will be sustai-ned.•All products are supposed to be used before the end of the period of 12 months based on the product date-code, if not a 100% solderabi-lity can´t be warranted.•Violation of the technical product specifications such as exceeding the nominal rated current will result in the loss of warranty.•Due to heavy weight of the components of size 1014, strong forces and high accelerations might have the effect to damage the electrical connection or to harm the circuit board and will result in the loss of warranty.1. General Customer ResponsibilitySome goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the are-as, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The responsibi-lity for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not.2. Customer Responsibility related to Specific, in particular Safety-Relevant ApplicationsIt has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime can-not be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications.In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component.3. Best Care and AttentionAny product-specific notes, warnings and cautions must be strictly observed.4. Customer Support for Product SpecificationsSome products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve spe-cific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter.5. Product R&DDue to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the customer as per Secti-on 1 and 2 remains unaffected.6. Product Life CycleDue to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a stan-dard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability ex-pectancy before or when the product for application design-in disposal is considered.The approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.7. Property RightsAll the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth Elektronik eiSos GmbH & Co. KG.8. General Terms and ConditionsUnless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth Elektronik eiSos Group”, last version available at .J Important Notes:The following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG:分销商库存信息: WURTH-ELECTRONICS 744732681。

74476012C;中文规格书,Datasheet资料

Bezeichnung :description :Größe / size 0805CA 2,28±0,2mmB 1,70±0,2mmC 1,28±0,2mmD 0,50 ref mm F 0,51 ref mm H 1,78 ref mm I 1,02 ref mm J0,76 ref mmB Elektrische Eigenschaften / electrical properties :Eigenschaften / properties Wert / valueEinheit / unittol.Induktivität /inductance Güte Q /Q factorDC-Widerstand /DC-resistance Nennstrom /rated currentEigenres.-Frequenz /self-res.-frequencyE Testbedingungen / test conditions :Luftfeuchtigkeit / humidity:33% Umgebungstemperatur / temperature:+20°CG Eigenschaften / general specifications :Keramik/ ceramic Lagerbedingungen / Storage conditions: -10°C ~ +40 °C 30 ~70 % RH Betriebstemperatur / operating temperature: -40°C - +125°CHBH Version 411-07-07ES Version 310-08-27SkleVersion 207-01-17SkleVersion 108-03-06Name Änderung / modificationDatum / datektronik eiSos GmbH & Co. KGGermany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400 min.R DCmin.L max.500 MHz∆T = 15 K250 MHz MHz.......................................................................................................................................................................................................Würth ElektronikCeramic-SMD-Inductor WE-KIKontaktmaterial/ contact platingFreigabe erteilt / general release:A Mechanische Abmessungen / dimensions :±5%22nHQ 55Artikelnummer / part number :Geprüft / checked 2600SRFDatum / date...........................................................................Unterschrift / signature Kontrolliert / approvedSpezifikation für Freigabe / specification for releaseDATUM / DATE : 2011-07-07max.mA Testbedingungen / test conditionsKunde / customer :74476012CBasismaterial / base material:F Werkstoffe & Zulassungen / material & approvalsENA 5071B für/for SRFD Prüfgeräte / test equipment :Agilent 4287A +HP 16193A für/for L und/and Q HP 4338B für/for R DCC Lötpad / soldering spec.:Ag + Ni + AuKunde / customer0,22I DC HP 4285A + 42841A + 42842C + 42851 - 6110 für/for I DC 500IJ IHThis electronic component has been designed and developed for usage in general electronic equipment. Before incorporating this component into any equipment where higher safety andreliability is especially required or if there is the possibility of direct damage or injury to human body, for example in the range of aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc, Würth Elektronik eiSos GmbH must be informed before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.LFAFBDCSEITE 1 VON 1/分销商库存信息: WURTH-ELECTRONICS 74476012C。

74458001;中文规格书,Datasheet资料

33% Umgebungstemperatur / temperature:+20°CFerrit/ ferrite MST 04-10-11NameDatum / dateÄnderung / modificationVersion 1Luftfeuchtigkeit / humidity:HP 34401 A für/for I DC und/and R DCHP 4274 A für/for L und/and Q Sockel / BaseAnbindung an Elektrode /Sn/Cu - 99.3/0.7%UL94-V0Endoberfläche / finishing electrode 100% Snhttp://www.we-online.deDatum / date.............................................................................Unterschrift / signature Kontrolliert / approvedWürth Elektronik eiSos GmbH & Co. KGD-74638 Waldenburg · Max-Eyth-Strasse 1 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked ................................................................................................It is recommended that the temperature of the part does not exceed 125°C under worst case operating conditions.Umgebungstemp. / ambient temperature: -40°C - + 85°C Basismaterial / base material:Draht / wire:2UEWF 155°C F Werkstoffe & Zulassungen / material & approvals:G Eigenschaften / general specifications:D Prüfgeräte / test equipment:E Testbedingungen / test conditions:Betriebstemp. / operating temperature: -40°C - + 125°C soldering wire to platingFreigabe erteilt / general release:Kunde / customerWürth Elektronik..................................................................................description :MST 04-10-11NameDatum / dateÄnderung / modificationVersion 1http://www.we-online.de................................................................................................Geprüft / checked Kontrolliert / approvedWürth ElektronikWürth Elektronik eiSos GmbH & Co. KGD-74638 Waldenburg · Max-Eyth-Strasse 1 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400...............................................................................................................................................................Datum / dateUnterschrift / signature DATUM / DATE : 2004-10-11H Induktivitätskurve / Inductance curve:Freigabe erteilt / general release:Kunde / customerPOWER-CHOKE WE-PD 4description :MST 04-10-11NameDatum / dateVersion 1http://www.we-online.deGeprüft / checked Kontrolliert / approvedWürth Elektronik eiSos GmbH & Co. KGD-74638 Waldenburg · Max-Eyth-Strasse 1 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Änderung / modificationWürth Elektronik...............................................................................................................................................................................................................................................................Datum / dateUnterschrift / signature Freigabe erteilt / general release:Kunde / customerPOWER-CHOKE WE-PD 4The force for tearing off cover tape is20 to 70 grams in arrow directionfeeding directionThis electronic component is designed and developed with the intention for use in general electronics equipments. Before incorporating the components into any equipments in the field such asaerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc. where higher safety and reliability are especially required or if there is possibility of direct damage or injury to human body. In addition, even electronic component in general electronic equipments, when use electrical circuits that require high safety, reliability functions or performance, the sufficient reliability evaluation-check for the safety must be performed before use. It is essential to give consideration when to install a protective circuit at the design stage分销商库存信息: WURTH-ELECTRONICS 74458001。

74477030;中文规格书,Datasheet资料

Bezeichnung :description := Start of winding Marking = Inductance code33% Umgebungstemperatur / temperature:+20°C100% SnMST 04-10-11MST 03-12-10RT 03-03-03MST02-03-27MST 02-02-20NameDatum / dateIt is recommended that the temperature of the part does not exceed 125°C under worst case operating conditions.Anbindung an Elektrode / soldering wire to plating:Sn/Ag/Cu - 96.5/3.0/0.5%Draht / wire:2SFBW 155°CUmgebungstemp. / ambient temperature: -40°C - + 85°C Freigabe erteilt / general release:Kunde / customerWürth Elektronik....................................................................................................................................................................Unterschrift / signature Ferrit/ferrite F Werkstoffe & Zulassungen / material & approvals :G Eigenschaften / general specifications :D Prüfgeräte / test equipment :E Testbedingungen / test conditions :Basismaterial / base material:Betriebstemp. / operating temperature: -40°C - + 125°C D-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked ..........................................................................................................................Kontrolliert / approvedWürth Elektronik eiSos GmbH & Co. KG74477030SPEICHERDROSSEL WE-PDPOWER-CHOKE WE-PDArtikelnummer / part number : Luftfeuchtigkeit / humidity:HP 4274 A für/for L und/and Q HP 34401 A für/for I DC und/and R DCÄnderung / modificationVersion 1Version 2Version 3Version 4Version 5 Datum / dateEndoberfläche / finishing electrode:• MarkingRoHS compliantLFdescription :MST 04-10-11MST 03-12-10RT 03-03-03MST02-03-27MST 02-02-20NameDatum / dateH Induktivitätskurve / Inductance curve :POWER-CHOKE WE-PDDATUM / DATE : 2004-10-11Kontrolliert / approvedDatum / dateUnterschrift / signature Würth ElektronikWürth Elektronik eiSos GmbH & Co. KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Freigabe erteilt / general release:Kunde / customer..................................................................................................................................................................................................................................................................................Geprüft / checked Version 4Version 5Änderung / modificationVersion 1Version 2Version 3a 330,0± 0,5mmb 20,20± 0,2mm+ 0,5- 1,0d 100,0± 0,2mmMST 04-10-11MST 03-12-10RT 03-03-03MST02-03-27MST 02-02-20NameDatum / dateRollenspezifikation / Reel specification:Freigabe erteilt / general release:Kunde / customerc 13,00mm....................................................................................................................................................................Datum / dateUnterschrift / signature Würth Elektronik..........................................................................................................................Würth Elektronik eiSos GmbH & Co. KGGeprüft / checked Kontrolliert / approvedD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Änderung / modificationVersion 1Version 2Version 3Version 4Version 5The force for tearing off cover tape is 10 to 130 grams in arrow direction165 to 180°feeding directionThis electronic component is designed and developed with the intention for use in general electronics equipments. Before incorporating the components into any equipments in the field such as aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc. where higher safety and reliability are especially required or if there is possibility of direct damage or injury to human body. In addition, even electronic component in general electronic equipments, when used in electrical circuits that require high safety, reliability functions or performance, the sufficient reliability evaluation-check for the safety must be performed before use. It is essential to give consideration when to install a protective circuit at the design stage.分销商库存信息: WURTH-ELECTRONICS 74477030。

7447745022;中文规格书,Datasheet资料

description := Start of winding Marking = Inductance code33% Umgebungstemperatur / temperature:+20°CFerritME09-05-19ME 07-04-21NameDatum / dateÄnderung / modificationVersion 1Version 2Typ MSKunde / customerFreigabe erteilt / general release:E Testbedingungen / test conditions:Luftfeuchtigkeit / humidity:It is recommended that the temperature of the part does not exceed 125°C under worst case operating conditions.F Werkstoffe & Zulassungen / material & approvals:Endoberfläche / finishing electrode:Sn/Cu - 99,3/0,7%Betriebstemp. / operating temperature: -40°C - + 125°C DATUM / DATE : 2009-05-19Datum / date..................................................................................Unterschrift / signature Kontrolliert / approvedWürth Elektronik eiSos GmbH & Co.KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked Umgebungstemp. / ambient temperature: -40°C - + 85°C Basismaterial / base material: G Eigenschaften / general specifications:POWER CHOKE WE-PD2D Prüfgeräte / test equipment:HP 4274 A für/for L und/and Q HP 34401 A für/for R DC und I DC......................................................................................................................................................................................................................................................Würth Elektronikdescription :ME09-05-19ME 07-04-21NameDatum / dateWürth ElektronikWürth Elektronik eiSos GmbH & Co.KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400....................................................................................................................................................................Datum / dateUnterschrift / signature Version 2POWER CHOKE WE-PD2DATUM / DATE : 2009-05-19H Induktivitätskurve / Inductance curve:Freigabe erteilt / general release:Kunde / customer....................................................................................................................................................................Geprüft / checked Kontrolliert / approvedÄnderung / modificationVersion 1description :A 6,10± 0,1a 330,0± 0,5mmb 21,0± 0,8mm + 0,5- 1,0d 100,0± 1,0mmME09-05-19ME 07-04-21NameDatum / dateÄnderung / modificationVersion 1Version 2c POWER CHOKE WE-PD2DATUM / DATE : 2009-05-19Würth Elektronik eiSos GmbH & Co.KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Gurtspezifikation / Tape specification:Rollenspezifikation / Reel specification:....................................................................................................................................................................Geprüft / checked Kontrolliert / approvedDatum / dateUnterschrift / signature Würth ElektronikFreigabe erteilt / general release:Kunde / customer....................................................................................................................................................................mm 13,00The force for tearing off cover tape is 20 to 70 grams in arrow directionfeeding directionThis electronic component has been designed and developed for usage in general electronic equipment. Before incorporating this component into any equipment where higher safety and reliability is especially required or if there is the possibility of direct damage or injury to human body, for example in the range of aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc, Würth Elektronik eiSos GmbH must be informed before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.J分销商库存信息: WURTH-ELECTRONICS 7447745022。

744731331;中文规格书,Datasheet资料

3.1 3.0 2.02012-06-282012-05-102011-04-07SStSStCZSStCZWürth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyTel. +49 (0) 79 42 945 - 0A Dimensions: [mm]F Typical Inductance vs. Current Characteristics:H4: Classification Wave Soldering Profile:H5: Classification Wave ProfileProfile FeaturePreheat- Temperature Min (T smin )- Temperature Typical (T stypical ) - Temperature Max (T smax ) - Time (t s ) from (T smin to T smax )Δ preheat to max Temperature Peak temperature (T p )Time of actual peak temperature (t p )Ramp-down rate - Min - Typical - MaxTime 25°C to 25°C Pb-Free Assembly 100°C 120°C 130°C 70 seconds 150°C max.250°C - 260°C max. 10 secondsmax. 5 second each wave ~ 2 K/s ~ 3.5 K/s ~ 5 K/s 4 minutesSn-Pb Assembly 100°C 120°C 130°C 70 seconds 150°C max.235°C - 260°C max. 10 secondsmax. 5 second each wave ~ 2 K/s ~ 3.5 K/s ~ 5 K/s 4 minutesrefer to EN 61760-1:2006H Soldering Specifications:I Cautions and Warnings:The following conditions apply to all goods within the product series of WE-TISof Würth Elektronik eiSos GmbH & Co. KG:General:All recommendations according to the general technical specifications of the data-sheet have to be complied with.The disposal and operation of the product within ambient conditions which probably alloy or harm the wire isolation has to be avoided.If the product is potted in customer applications, the potting material might shrink during and after hardening. Accordingly to this the product is exposed to the pressure of the potting material with the effect that the core, wire and termination is possibly damaged by this pressure and so the electrical as well as the mechanical characteristics are endanger to be affected. After the potting material is cured, the core, wire and termination of the product have to be checked if any reduced electrical or mechanical functions or destructions have occurred.The responsibility for the applicability of customer specific products and use in a particular customer design is always within the authority of the customer. All technical specifications for standard products do also apply for customer specific products.Washing varnish agent that is used during the production to clean the application might damage or change the characteristics of the wire in-sulation, the marking or the plating. The washing varnish agent could have a negative effect on the long turn function of the product.Direct mechanical impact to the product shall be prevented as the ferrite material of the core could flake or in the worst case it could break. Product specific:Follow all instructions mentioned in the datasheet, especially:•The solder profile has to be complied with according to the technical wave soldering specification, otherwise no warranty will be sustai-ned.•All products are supposed to be used before the end of the period of 12 months based on the product date-code, if not a 100% solderabi-lity can´t be warranted.•Violation of the technical product specifications such as exceeding the nominal rated current will result in the loss of warranty.1. General Customer ResponsibilitySome goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the are-as, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The responsibi-lity for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not.2. Customer Responsibility related to Specific, in particular Safety-Relevant ApplicationsIt has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime can-not be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications.In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component.3. Best Care and AttentionAny product-specific notes, warnings and cautions must be strictly observed.4. Customer Support for Product SpecificationsSome products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve spe-cific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter.5. Product R&DDue to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the customer as per Secti-on 1 and 2 remains unaffected.6. Product Life CycleDue to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a stan-dard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability ex-pectancy before or when the product for application design-in disposal is considered.The approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.7. Property RightsAll the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth Elektronik eiSos GmbH & Co. KG.8. General Terms and ConditionsUnless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth Elektronik eiSos Group”, last version available at .J Important Notes:The following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG:分销商库存信息: WURTH-ELECTRONICS 744731331。

7443310033;中文规格书,Datasheet资料

Bezeichnung :description :33%Umgebungstemperatur / temperature:+20°CIron Powder Core Lagertemp. / storage temperature: -40°C - +60°C BD09-11-03Rst 08-11-11NameDatum / dateÄnderung / modificationVersion 1Version 2Luftfeuchtigkeit / humidity:It is recommended that the temperature of the part does HP 34401 A & Fluke 54II für/for I DC; SPEICHERDROSSEL WE-HCC 1210 (Eisenpulver)POWER-CHOKE WE-HCC 1210 (Iron Powder)Artikelnummer / part number :7443310033D-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked .................................................................................................Basismaterial / base material:Metra HIT 27I für/for R DCArbeitstemperatur / operating temperature: -40°C - +125°C WAYNE KERR 3260B für/for L 0; I SAT D Prüfgeräte / test equipment:E Testbedingungen / test conditions:Kunde / customerF Werkstoffe & Zulassungen / material & approvals:G Eigenschaften / general specifications:not exceed 125°C under worst case operating conditions.Draht / wire:JIS 155°C , UL : E201757Würth Elektronik..................................................................................Freigabe erteilt / general release:http://www.we-online.deDatum / date.............................................................................Unterschrift / signatureKontrolliert / approvedWürth Elektronik eiSos GmbH & Co. KGmarkingBezeichnung :description :H Induktivitätskurve / Inductance curve:BD09-11-03Rst 08-11-11NameDatum / dateSPEICHERDROSSEL WE-HCC 1210 (Eisenpulver)POWER-CHOKE WE-HCC 1210 (Iron Powder)DATUM / DATE : 2009-11-03Freigabe erteilt / general release:Kunde / customer...............................................................................................................................................................Datum / dateUnterschrift / signature Würth ElektronikVersion 2..........................................................................................................................................Version 1D-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400http://www.we-online.deGeprüft / checked Kontrolliert / approvedÄnderung / modificationWürth Elektronik eiSos GmbH & Co. KGBezeichnung :description :I Temperaturanstieg / Temperature rise curve:BD09-11-03Rst 08-11-11NameDatum / dateDATUM / DATE : 2009-11-03Version 1D-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400...............................................................................................................................................................Datum / dateUnterschrift / signaturehttp://www.we-online.deGeprüft / checked Kontrolliert / approvedÄnderung / modificationWürth Elektronik eiSos GmbH & Co. KGSPEICHERDROSSEL WE-HCC 1210 (Eisenpulver)POWER-CHOKE WE-HCC 1210 (Iron Powder)Freigabe erteilt / general release:Kunde / customerWürth ElektronikVersion 2..........................................................................................................................................Bezeichnung :description :BD09-11-03Rst 08-11-11NameDatum / dateSPEICHERDROSSEL WE-HCC 1210 (Eisenpulver)POWER-CHOKE WE-HCC 1210 (Iron Powder)Freigabe erteilt / general release:Kunde / customer...............................................................................................................................................................Datum / dateUnterschrift / signature Würth ElektronikVersion 2............................................................................................................................................Version 1D-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked Kontrolliert / approvedÄnderung / modificationWürth Elektronik eiSos GmbH & Co. KGThe Force for tearing off cover tape is 20 to 70 grams in arrow direction150°feeding directionThis electronic component has been designed and developed for usage in general electronic equipment. Before incorporating this component into any equipment where higher safety and reliability is especially required or if there is the possibility of direct damage or injury to human body, for example in the range of aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc, Würth Elektronik eiSos GmbH must be informed before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.分销商库存信息: WURTH-ELECTRONICS 7443310033。