RG-AP530-I灵动天线型802.11ac无线接入点
Ruijie RG-AP630 (CD) 无线接入点快速安装指南说明书

Ruijie RG-AP630 (CD) Wireless Access Points Quick Installation GuideCopyright StatementRuijie Networks©2019Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup, modification, transmission, translation or commercial use of this document or any portion of this document, in any form or by any means, without the prior written consent of Ruijie Networks is prohibited.Exemption StatementThis document is provided “as is”. The contents of this document are subject to change without any notice. Please obtain the latest information through the Ruijie Networks website. Ruijie Networks endeavors to ensure content accuracy and will not shoulder any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.Means reader take note. Notes contain helpful suggestions or references.Mounting Plate Mounting Bracket Tie Rod M8X40/M8X20 Screw Grounding Cable Hose ClampLiquid-tight Adapter for Optical Fiber Security Cable M8x60 Expansion Bolt1. Console port2. 10/100/1000 Base-T auto-sensing Ethernet/PoE IN port3. SFP combo portAttach the tie rod to the mounting plate and fasten the rod with the M8x40 screws after AP is well-positioned, shown in the following figure.Attach the mounting plate to the mounting bracket through the rod with the M8x40 screws, adjust AP orientation, and tighten the screws on the rod with the Phillips screwdriver (or the wrench). Finally, connect Loop B of the security cable to the bracket by fastening the screw attached to Loop BHorizontal pole mount is also supported. The procedure of horizontal pole mount is similar as that of vertical mount.The outdoor AP can be mounted on a wall and a pole (diameter: 75 mm to 120 mm). If the diameter of the pole is out of the range, the hose clamp is customer-supplied. In this case, we strongly recommend you to use a 304 stainless steel hose clamp with thickness of 2.5mm at least.8Mounting the AP on the WallAttach the mounting bracket to the wall with user-supplied expansion screws. M8 x 60 screws are recommended. Mark the locations of the four screw holes by using the marker. Drill four 8 mm diameter holes. Tap expansion anchorsAttach the tie rod to the mounting plate and fix the rod with the supplied M8x40 screws. Adjust the AP orientation, and drive the two-side screws on the rod. Finally, drive the screw of Loop B into the fourth anchor.Connecting the Fiber CableThe liquid-tight adapter for optical fiber is supplied for hardware V2.00 and laterWaterproofing material is customer-supplied.1)Choose an LC-LC optical fiber with the diameter of 2.7±0.2mm.Thread the fiber through the liquid-tight adapter in the order as shown.10Thread the original network cable through the liquid-tight adapter.Attach the plug into one end of the network cable nearest to the head of the liquid-light adapter.Insert the plug into the PoE IN port, and tighten the liquid-tight adapter.Make sure the plug is correctly inserted.improperly. Before removing the network cable, dismantle the liquid-tight adapter first and then the plug. 11The lock loop on the AP is for your security needs. You can fasten the AP to a fixture for anti-theft. of a security lock to a fixture. Second, secure the lock plate into the lock loop.。
RG-AP530-I灵动天线型802.11ac无线接入点

锐捷网络股份有限公司了解更多产品信息,欢迎登陆 ,咨询电话:400-620-8818。
RG-AP530-I灵动天线型802.11ac无线接入点产品简介RG-AP530-I是锐捷网络推出的搭载“X-sense”灵动天线的802.11ac无线接入点(AP)产品,支持三条空间流技术,单路射频单元可以提供高达1300Mbps的接入速率,整机提供1900Mbps的接入速率,近千兆的极速无线让性能不再成为瓶颈。
RG-AP530-I同时搭载了业界领先的“X-sense”灵动天线,跨越式的提升了AP的覆盖性能,保障了移动智能终端最优的接入效果。
RG-AP530-I产品充分考虑了无线网络安全、射频控制、移动访问、服务质量保证、无缝漫游等重要因素,配合锐捷网络WS系列无线控制器产品,完成无线用户数据转发、安全和访问控制。
RG-AP530-I采用双路双频设计,可支持同时工作在802.11ac和802.11n模式。
该产品呈壁挂式,可安全方便的安装于墙壁、天花板等各种位置。
RG-AP530-I产品可支持本地供电与远程以太网供电模式,可根据客户现场供电环境进行灵活选择,特别适合部署在大型校园、企业办公、医院、运营热点等环境。
产品特性与价值X-sense:会思考的灵动天线■1677万种天线路径选择,覆盖无死角锐捷网络创新研发的X-sense灵动天线矩阵架构,能够动态选择不同的天线组合,支持最高多达1677万种组合方案,彻底解决传统天线存在覆盖盲区的弱点。
无论在任何角落,X-sense都能定制出一条最适合移动智能终端当前位置的天线路径,真正实现全面覆盖,绝无死角。
■全自动调节,让信号随你而“动”无论终端如何移动,都有最佳的信号路径跟随,这是X-sense灵动天线技术带来的革命性改变。
无需人工干预,X-sense凭借其强大的运算性能,可以在1毫秒内完成300次指向终端的信号路径切换,即便在快速奔跑状态下也能保证时刻都有最佳的信号与终端同“行”。
802.11ac:第五代Wi-Fi技术

802.11ac:第五代Wi-Fi技术Aug, 2012802.11ac:第五代Wi-Fi技术1.概要 (3)2.什么是802.11AC? (5)2.1802.11AC的驱动力 (5)2.2802.11AC的速度为何这么快? (6)2.3我们如何保证802.11AC的健壮性? (9)2.3.1 技术综述 (9)2.3.2 802.11ac和802.11n的区别 (11)2.3.3 基于标准的波束成形 (13)2.3.4 基于带宽指示的RTS/CTS (14)2.3.5 所有的A-MPDU (16)2.3.6 信道化和80+80MHz (17)2.3.7 数据速率与覆盖范围 (21)2.3.8 频谱管制 (22)2.3.9 多用户MIMO (23)2.3.10 802.11ac项目授权请求 (24)3. 802.11AC什么时候才会到来? (25)4. 802.11AC如何影响我们? (26)4.1兼容性 (26)4.2什么时候更新到802.11AC? (28)4.3无线电资源管理和无线入侵保护系统(WIPS)效果 (29)5. 总结 (29)附录:什么是802.11N? (30)2012 Cisco and/or its affiliates. All rights reserved.1.概要802.11ac作为IEEE的新标准借鉴并更进一步地优化了802.11n的优点。
802.11ac是一个更快且更易扩展的802.11n版本。
802.11ac结合了无线技术的灵活与千兆以太网的高容量。
无线局域网站点中每个无线接入点所用支持的用户数量会获得极大的改进,每个用户能够拥有更好的体验,并且能够为更多的并行视频流提供更多的可用带宽。
即使当网络没有满载时,用户也能看到好处:文件下载及电子邮件的同步能够达到低延迟的千兆速度。
此外,由于设备的WiFi接口能够被及时唤醒,与无线接入点交换数据后更快地进入待机状态,设备的电池寿命也被延长了。
RG-AP520系列无线接入点硬件安装手册(V1

1 产品介绍锐捷RG-AP520无线局域网接入设备(简称AP520)是锐捷网络自主研发的无线接入点产品之一。
主要应用于室内比较复杂的环境,既可以作为瘦AP( Fit AP ),与有线无线一体化交换机/无线控制器合组网。
也可以作为胖AP( Fat AP ) 独立进行组网,为无线局域网用户提供无线接入服务。
1.1 RG-AP520规格参数硬件规格射频设计 2.4G:2×2MIMO5G:2×2MIMO传输协议 2.4G :802.11b/g/n5G :802.11a/n/ac工作频段802.11b/g/n :2.4G ~ 2.4835GHz802.11a/n/ac :5G:5.150~5.350GHz,5.47~5.725,5.725~5.850GHz (注:工作频段根据不同国家配置有所变化)天线类型内置全向3dBi空间流数2条流传输速率 2.4G提供最高提供300Mbps的接入速率,5G提供最高提供867Mbps的接入速率。
整机提供1.167Gbp的接入速率。
调制技术OFDM:BPSK@6/9Mbps,QPSK@12/18Mbps,16-QAM@24Mbps,64-QAM@48/54Mbps DSSS:DBPSK@1Mbps,DQPSK@2Mbps,and CCK@5.5/11MbpsMIMO-OFDM:BPSK,QPSK,16QAM 、64QAM and 256QAM接收灵敏度11b:-99dBm(1Mbps),-93dBm(5.5Mbps),-90dBm(11Mbps)11a/g:-93dBm(6Mbps),-85dBm(24Mbps),-82dBm(36Mbps),-77dBm(54Mbps)11n:-92dBm@MCS0,-74dBm@MCS7,-92dBm@MCS8,-73dBm@MCS1511ac HT20:-90dBm(MCS0), -65dBm(MCS8)11ac HT40:-85dBm(MCS0), -60dBm(MCS9)11ac HT80:-82dBm(MCS0), -58dBm(MCS9)最大发射功率27dBm实际发射功率遵照不同国家和地区法规而有所不同。
锐捷RG-AP630 802.11ac户外无线AP 数据表说明书

RUIJIE NETWORKS COMPANY LIMITEDRuijie RG-AP630 is a top-class 802.11ac outdoor wireless access point for the next-generation high-speed wireless network, offering access rates of up to 1.75Gbps. The RG-AP630 AP takes all the important factors into account including wireless security, RF control, mobile access, QoS, seamless roaming, etc. Teaming up with Ruijie RG-WS Wireless Controller Series, the AP offers Wi-Fi user data forwarding, advanced security and access control.The rugged enclosure of RG-AP630 (IP67 rated) is designed to withstand extreme outdoor conditions and simplify device installation and maintenance. In addition to the built-in antenna, the RG-AP630 AP supports automatic switching between the external and internal antennas to adapt to various application scenarios such as large campus, enterprises, hospitals, commercial towers, etc. Moreover, the RG-AP630 AP supports a PoE OUT interface of 802.3at standard, which is one of the features facilitating streamlined integration with other monitoring devices, providing high-quality, real-time transmission of surveillance data. Multi-hop and point-to-multipoint wireless bridge features further enhance the application flexibility. The outdoor RG-AP630 thereby offers unparalleled productivity in a wide variety of outdoor networking solutions.PRODUCT FEATURESHigh Performance & Reliability802.11ac Superior Wireless PerformanceThe RG - A P630 AP supports 802.1n @2.4GHz and 802.11ac@5GHz protocols and offers maximum access rates of up to 1.75Gbps. The superior wireless performance greatly optimizes users’ wireless experience, increases the number of concurrent users as well as signal coverage.High-performance Built-in X-Sense Smart AntennaRuijie’s built-in patented X-Sense Smart Antenna achieves real-time antenna beam switching, offering the best wireless experience according to the location of access devices. The built-in X-Sense Smart Antenna can provide up to 90 degree coverage and basic gain of 10dBi which can meet the coverage requirements of most outdoor scenarios, protecting users’ investment with aesthetic design and ease of installation.External Antenna with Lightning ProtectionRG-AP630 supports external antenna via software configuration.By selecting the suitable external antenna model (e.g. antenna with higher gain or larger beam angle), the RG-AP630 can support more coverage scenarios. The RG-AP630 adopts the high-reliability N-type waterproof connectors with built-in surge protection circuit, which requires no additional installation of lightning protection device to reduce customers’ investment and simplify deployment.The Industry’s Most Flexible Gigabit UplinkRG-AP630 offers a 10/100/1000Base-T Ethernet uplink port so that the wired ports are no longer the bottleneck of wireless access rates. RG-AP630 also delivers a Gigabit SFP combo port to adapt to the existing wired network of customers’ sites, providing more flexible and convenient networking.INNOVATION BEYOND NETWORKS1Unique PoE OUT DesignThe RG-AP630 AP supports unique PoE OUT design, transferring power directly to the video surveillance equipment at deployment location. The surveillance video data is transmitted back to the control room in real-time via wired or wireless network. This feature not only reduces the difficulty of surveillance device installation, but also lowers the cabling cost.Flexible Mount-KitWith the adjustable mount-kit, the RG-AP630 AP can be adjusted -60°~60° horizontally and -60°~90° vertically to simplify the optimization of wireless network coverage. Wide Operating Temperature RangeThe components and enclosure of RG-AP630 can withstand a wide temperature range. The AP can operate within a wide temperature range from -40 to 65 without affecting its stability and lifetime.Flexible & Comprehensive Security Policies User Data EncryptionThe RG-AP630 AP offers protected Wi-Fi access with the support of cutting-edge encryption technologies such as WEP, TKIP and AES to guarantee the data transmission security of the wireless network.Flexible WDS ModeSupporting the WDS (Wireless Distribution System), the RG-AP630 AP offers AP coverage or wireless network bridge. The RG-AP630 AP supports WDS bridge of 5 hops or fewer. Wireless bridging can be achieved even at remote distance. The outdoor AP also supports point-to-multipoint bridging which enhances deployment flexibility. The features enable large-scale wireless coverage and remote high-speed wireless connection, which enhance the flexibility of outdoor wireless deployment.Industry-Leading Local Forwarding Technology Employing an industry-leading local forwarding technology, the RG-AP630 AP eliminates the traffic bottleneck of wireless access controllers. Deploying with the Ruijie RG-WS Wireless Controller Series, users can flexibly pre-configure the data-forwarding mode of RG-AP630. The RG-AP630 AP also controls if the data will be forwarded via the wireless controller. The local forwarding technology can forward large-scale, delay-sensitive, and real-time transmission data to greatly alleviate the traffic pressure on the wireless LAN controllers and fulfill the high traffic transmission requirements of the 802.11ac network.Seamless Roaming ExperienceThe RG-AP630 AP teams up with the RG-WS Wireless ACs in perfect harmony, allowing wireless users to roam seamlessly on Layer 2 and Layer 3 networks without data interruption.Abundant QoS PoliciesThe RG-AP630 AP supports a wide range of QoS policies. For example, it provides bandwidth limitations in WLAN/AP/STA modes that define different priorities for different service data.Outstanding Environmental AdaptabilityThe RG-AP630 AP does not only offer a simple and stylish design, but also an IP67-rated enclosure with waterproof, dustproof, moisture-proof and flame retardant design to deliver the best performance even in long-term outdoor condition and allow the device to operate in harsh environments such as wind erosion, rain and high humidity. In addition, the outstanding environmental adaptability greatly lengthens the lifetime of the equipment and effectively reduces the maintenance cost. Virtual Wireless Packet TechnologyWith the virtual AP technology, the Ruijie RG-AP630 can offer 14 ESSIDs within the network and support 14 802.1Q VLANs. The network administrators can separately encrypt and isolate subnets or VLANs that have the same SSID. A separate authentication mode and encryption mechanism for each SSID can be configured flexibly.Standard CAPWAP EncryptionThe Ruijie RG-WS Wireless Controller Series manages the RG-AP630 AP with the adoption of the international CAPWAP standard (Control and Provisioning of Wireless Access Points) to ensure the security of the data transmission process.RF SecurityDeploying with Ruijie’s integrated network management system RG-SNC and RG-WS Series Wireless Controllers, the Ruijie RG-AP630 enables the RF probe scanning mechanism to detect unauthorized access points or other RF interference sources. Once detected, the Ruijie RG-AP630 will send real-time alert notifications to the network management system. The network administrators can monitor potential threats and usage status in the wireless environments with ease.User Access ControlThe RG-AP630 AP supports multiple authentication methods such as Web, 802.1x, MAC address and local authentication for customers' choice. The AP also supports Ruijie’s advanced Security Management Platform (SMP) BYOD Solution which complies with a standard access control system. The system has a set of control policies in terms of user access, authorization, host compliance check, network behavior monitoring, network attack defense, etc. All these control features ensure that users are authenticated before accessing the network services securely.Comprehensive Wireless ProtectionTogether with Ruijie’s RG-SNC network management system and RG-WS Wireless ACs, the RG-AP630 AP provides a powerful range of wireless security features such as Wireless Intrusion Detection System (WIDS), RF Interference Location, Rogue AP Countermeasures, Anti-ARP Spoofing and DHCP protection. The AP offers a truly secure and reliable wireless network.INNOVATION BEYOND NETWORKS 2Model RG-AP630(IODA) RG-AP630(IDA) RG-AP630(CD) Operating Temperature -40~65Operating Humidity 0~100%RH (Non-condensing)Protection Rating IP67Weight <2.5kgSafety Standard GB4943, EN60601-1-2 (medical), UL / CSA 60950-1, EN / IEC60950-1, EN / IEC 60950-22EMC GB9254-2008, EN301 489, EN55022, FCC Part15, RSS-210Software SpecificationsMaximum stations per AP 256SSID hiding YesConfiguring the authentication mode,encryption mechanism, and VLAN Yesattributes for each SSIDWDS (bridge mode) YesRemote Intelligent PerceptionYes WLAN Technology (RIPT)X-speed YesIntelligent identification of smart device YesIntelligent load balancing based on theYes number of users or trafficSTA limit SSID-based Radio-basedBandwidth limit STA/SSID/AP-based rate limit PSK, Web, and 802.1x authentication YesData encryption WPA (TKIP), WPA2 (AES), WPA-PSK, and WEP (64 or 128 bits)QR code authentication YesSMS authentication YesPEAP authentication YesData frame filtering Whitelist, static blacklist, and dynamic blacklistUser isolation YesSecurity Rogue AP detection and countermeasure YesDynamic ACL assignment YesRADIUS YesCPU Protection Policy (CPP) YesNetwork Foundation Protection PolicyYes(NFPP)WIDS (Wireless Intrusion DetectionYesSystem)Remote probe YesIPv4 address Static and dynamic IP addressRouting IPv6 transparent transmission YesMulticast Multicast to unicast conversionINNOVATION BEYOND NETWORKS 4This material was made in 2015. The pictures and technical data inside are only for reference. All rights reserved. INNOVATION BEYOND NETWORKS。
RG-AP530-I系列无线接入点硬件安装手册(V1.1)

认证 加密 WIDS GSN CPU 保护策略 基础网络保护策略 管理特性 网络管理 日志 告警 故障检测 统计信息 Fat/Fit 模式切换 物理特性 尺寸 重量 安装方式 业务端口 管理端口 射频接口 电源 工作频段 调制技术
发射功率
接收灵敏度
RG-AP530-I 系列无线接入点硬件安装手册 通过 IP40 防水防尘认证 工作温度:-10°C~55°C 存储温度:-40°C~70°C 工作湿度:5%~95%(无凝结) 存储湿度:0%~100%(无凝结) 19W GB4943、EN/IEC 60950-1 GB9254、EN301 489 EN 62311 无线发射设备型号核准、EN300 328、EN301 893
技术支持 4008-111-000
前
使用范围
言
感谢您使用锐捷网络产品,本手册为您提供了详细的硬件安装指南。
本手册主要介绍了产品在功能上和物理上的一些特性,提供了安装步骤、故障排除、技术规格,以及电缆和连接器的规格和 使用准则。 适用于想对上述内容进行了解且在安装和维护网络硬件方面具有一定经验的用户。 同时假定该款产品的用户熟知 相关术语和概念。
RG-AP530-I 系列无线接入点硬件安装手册
1 产品综述
1.1 产品简介
RG-AP530-I 是锐捷网络推出的面向下一代高速无线网络的无线接入点产品,采用了最新标准的 802.11ac 协议,每路射频 单元可以提供高达 1300Mbsp 的接入速率,单个 AP 可以提供 1900Mbps 的接入速率。RG-AP530-I 产品充分考虑了无线网 络安全、射频控制、移动访问、服务质量保证、无缝漫游等重要因素,配合锐捷网络 RG-WS 系列无线控制器产品,完成无 线用户数据转发、安全和访问控制。 RG-AP530-I 支持标准的 802.11ac 协议,采用双路双频设计,可支持同时工作在 802.11a/n/ac 和 802.11b/g/n/ac 模式。提 供两个 10/100/1000Base-T 以太网端口上联。 RG-AP530-I 采用了业内领先的双路大功率射频硬件设计,双路均具备 100mW 双向功率放大能力,可根据不同的环境和覆 盖需求,配合相应的内置式天线,为用户带来饱满的信号覆盖体验,可完全保障信号在视距和非视距的传输,并专门针对穿 透障碍物能力进行了加强,较低的噪声指数提高了接收灵敏度,更使得覆盖范围大大增加,内建的高速加密引擎,可支持所 有 TKIP 及 AES 协议且不会出现性能衰减。 RG-AP530-I 采用锐捷网络创新研发的 X-sense"灵动"天线矩阵架构,能够动态选择不同的天线组合,支持最高多达 1677 万种组合方案,彻底解决传统天线存在覆盖盲区的弱点。无论你身处哪个角落,X-sense 都能定制出一条最适合你当前位置 的天线路径,真正实现全面覆盖,绝无死角。无需人工干预,X-sense 凭借其强大的运算性能,可以在 1 毫秒内完成 300 次指向终端的信号路径切换,即便在快速奔跑状态下也能保证时刻都有最佳的信号。
ExtremeWireless 802.11ax AP310i e 室内接入点 用户手册说明书

ExtremeWireless 802.11ax AP310i/e 室内接入点AP310i/e 概述AP310i/e 接入点是室内型号 802.11ax 接入点。
AP310i 中的“i”表示接入点带有内部天线,“e”表示它带有外部天线连接器。
接入点具有内置双频无线电、两个带锁无线电、四个 WiFi 内部或外部天线以及一个低功耗蓝牙(BLE)天线。
AP310i/e 可以安装到墙壁、实心天花板等平整表面以及接线盒/电工箱上,也可以安装在吊顶上。
AP310i/e 接入点具有以下特点:•无线电:– 2 个 802.11ax 无线电(1 个2X2 2.4GHz和5 GHz无线电和1个2X2 5 GHz无线电)–1个物联网无线电(2.4 GHz)•控制台端口RJ45• 2 个 1G 以太网端口:–GE1 端口 –GE2 端口•LED 指示灯:6个–重置过程中所有 LED 指示灯都将亮起。
• 1 个重置按钮• 1 个防盗锁插孔• 1 个安全吊架• 1 个 USB 2.0 A 型连接器•功率:PoE 802.3at 和 802.3bt(有关详细信息,请参见Table 1)•天线:–AP310i:4 个 WiFi内部天线和一个 BLE 内部天线–AP310e:4个 RP-SMA外部天线端口和 1 个 BLE RP-SMA 天线•温度:–AP310i:0°C 至 +50°C (32°F 至 +122°F) –AP310e:-20°C 至 +55°C (-4°F 至 +131°F) •外壳:塑料表 1AP310i/e 电源图 1 AP310i 和AP310e 的前视图LED 指示灯LED 指示灯位于接入点的正面,但没有明显标记。
表 2AP310i/eLED 状态说明: AP310i/e最低需要 WiNG 7.3.1 基本固件。
电源介绍以太网供电 (PoE)电源通过 1G 以太网端口提供AP310i/e,符合802.3at 和 802.3bt 的电源要求,以提供全部功能。
ExtremeWireless 802.11ax AP460i e 室外接入点说明书

ExtremeWireless 802.11ax AP460i/e 室外接入点AP460i/e 概述AP460i/e 接入点是室外型企业级 802.11ax 接入点。
AP460i 中的“i”表示接入点带有内部天线,“e”表示它带有外部天线连接器。
接入点具有内置双频无线电、2 个锁频无线电、8 个 WiFi 内部或外部天线以及 1 个蓝牙低功耗(BLE)天线。
AP460i/e 可以安装在平整表面上,如墙壁或立杆。
AP460i/e 接入点具有以下特点:•无线电:– 3 个 802.11ax 无线电(1 个 2X2 2.4 GHz 无线电、1 个 4X4 5 GHz 无线电及 1 个 2X2 2.4 GHz 和 5 GHz 无线电)– 1 个物联网无线电(2.4 GHz)•控制台端口RJ45• 2 个以太网端口:– 1 个 100/1000/2500 Mbps 自动协商以太网端口,RJ45– 1 个 10/100/1000 Mbps 自动协商以太网端口,RJ45•LED 指示灯:7–所有 LED 灯将在重置期间亮起,并连接到通用输入/输出(GPIO)引脚• 1 个重置按钮•功率:PoE 802.3af(详见Table 1)•天线:–8 个 WiFi 内部/外部天线–一个AP460i上的 BLE 内部天线在 和一个AP460e上的 BLE 外部天线端口•温度:–-40°C 至 +60°C (-40°F 至 +140°F)•外壳:塑料表 1AP460i/e 电源图 1 AP460i 和AP460e 的前视图LED 指示灯LED 指示灯位于接入点的正面,但没有明显标记。
表 2AP460i/eLED 指示灯AP460i/e 盒内项目确保以下项目可用:说明: AP460i/e最低需要 WiNG 7.3.0 基本固件。
电源介绍以太网供电 (PoE)电源通过AP460i/e的 RJ45 以太网端口提供,符合 802.3at 和 802.3bt 提供完整功能的供电要求。
- 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。
锐捷网络股份有限公司了解更多产品信息,欢迎登陆 ,咨询电话:400-620-8818。
RG-AP530-I灵动天线型802.11ac无线接入点产品简介RG-AP530-I是锐捷网络推出的搭载“X-sense”灵动天线的802.11ac无线接入点(AP)产品,支持三条空间流技术,单路射频单元可以提供高达1300Mbps的接入速率,整机提供1900Mbps的接入速率,近千兆的极速无线让性能不再成为瓶颈。
RG-AP530-I同时搭载了业界领先的“X-sense”灵动天线,跨越式的提升了AP的覆盖性能,保障了移动智能终端最优的接入效果。
RG-AP530-I产品充分考虑了无线网络安全、射频控制、移动访问、服务质量保证、无缝漫游等重要因素,配合锐捷网络WS系列无线控制器产品,完成无线用户数据转发、安全和访问控制。
RG-AP530-I采用双路双频设计,可支持同时工作在802.11ac和802.11n模式。
该产品呈壁挂式,可安全方便的安装于墙壁、天花板等各种位置。
RG-AP530-I产品可支持本地供电与远程以太网供电模式,可根据客户现场供电环境进行灵活选择,特别适合部署在大型校园、企业办公、医院、运营热点等环境。
产品特性与价值X-sense:会思考的灵动天线■1677万种天线路径选择,覆盖无死角锐捷网络创新研发的X-sense灵动天线矩阵架构,能够动态选择不同的天线组合,支持最高多达1677万种组合方案,彻底解决传统天线存在覆盖盲区的弱点。
无论在任何角落,X-sense都能定制出一条最适合移动智能终端当前位置的天线路径,真正实现全面覆盖,绝无死角。
■全自动调节,让信号随你而“动”无论终端如何移动,都有最佳的信号路径跟随,这是X-sense灵动天线技术带来的革命性改变。
无需人工干预,X-sense凭借其强大的运算性能,可以在1毫秒内完成300次指向终端的信号路径切换,即便在快速奔跑状态下也能保证时刻都有最佳的信号与终端同“行”。
■功率不变,却有3倍的信号提升X-sense能够精确计算终端的位置,并通过动态组合的天线模式,针对每个终端位置来提升不同的信号强度,最大可以提升到普通AP的3倍,这使得覆盖范围内无论远近的各个点都能接收最佳信号。
而且完全不用担心由此带来的辐射增加,因为增强的信号强度都全部被用来抵消传输路径和穿透墙壁的损耗,AP的发射功率都是完全符合国家标准。
■终端接入优化设计,更适合手机和平板电脑用户当移动智能终端接入无线网络时,X-sense会快速、准确的识别到终端的类型,如果是使用功率较低的手机、平板电脑等移动终端时,X-sense能够通过动态信号补偿技术,针对移动终端802.11ac协议,最高连接速率可以达到1.3Gbps;2.4GHz沿用原802.11n无线标准,最高连接速度可达600Mbps,而且完全向下兼容a/b/g,实现平滑过渡;双频同时开启,高达1.9Gbps的极速无线,相比以往下载等无线数据传输,时间至少缩短了80%,带来真正的高速极致体验。
■绿色环保,手机WiFi用更久大量的节能新技术被应用到了RG-AP530-I中,这包括了:单天线待机技术,动态MIMO省电技术,增强型自动省电传送技术,逐包功率控制技术等,结合高性能的电源设计,使得RG-AP530-I在提供高速无线接入的同时,轻松节省了25%的电能。
■智能识别功能支持终端智能识别,能够识别出Apple、Android等智能移动终端和PC机。
■业界领先的本地转发RG-AP530-I继承了锐捷网络一贯领先的智能本地化转发技术,彻底突破了无线控制器的流量瓶颈的限制。
通过锐捷网络RG-WS系列无线控制器的配合,可灵活预配置RG-AP530-I产品的数据转发模式,根据SSID名称或者用户VLAN以决定是否需要经过无线控制器转发,或直接进入有线网络进行数据交换。
通过本地转发技术可以将延迟敏感、传输要求实时性高的数据分类通过有线网络转发,可以大大缓解无线控制器的流量压力,更好的适应802.11n网络高流量传输的要求。
■丰富的服务质量保证(QoS)RG-AP530-I支持丰富的服务质量保证(QoS),支持WLAN/AP/STA多种模式的带宽限制、支持对不同业务数据定义优先级的WMM(wifi multimedia)等,真正实现了影音传输能及时、定量、保证多媒体的顺畅应用。
RG-AP530-I支持的组播转单播技术彻底解决了无线网络中视频点播等组播应用下掉包、时延大导致视频不流畅的问题,优化了组播视频业务在无线网络中体验。
智慧灵动的无线体验■X-speed极速无线体验RG-AP530-I在多AP干扰的情况下,有效的缩短了下联用户发送无线数据包的竞争等待时间,让使用锐捷无线网络的用户在复杂环境中仍能体验极速无线。
RG-AP530-I同时解决了因终端无线网卡老旧或终端离AP较远而导致用户无线上网延时大、速度慢、AP整机性能低下的问题,为所有类型的终端分配相同的无线链路使用时间,不仅提升了AP 的整机吞吐性能,并保证了每个终端都能公平高速的访问无线网络。
■终端智能识别RG-AP530-I配合锐捷无线控制器,能根据终端特点,智能识别终端类型,自适应弹出不同大小、页面格局的Portal认证页面。
终端智能识别技术免去了用户多次拖动,调整屏幕的操作,相比原来节省了近10s的时间,为用户提供更加快捷的无线体验,并且全面支持苹果iOS、安卓和windows等主流智能终端操作系统。
■边缘智能感知传统“瘦AP+无线控制器”的集中式网络体系架构,无线数据流经AP再到无线控制器进行集中转发,这就会存在当无线控制器发生故障宕机后,AP无法正常工作的问题,导致整个无线网络瘫痪。
而锐捷网络最新的边缘智能感知技术,使RG-AP530-I能够智能的进行链路感知,当发现无线控制器故障宕机后,AP快速切换为智能模式继续进行数据转发,实现了无线网络的高可用性,真正的做到了无线用户永不掉线。
■智能负载均衡在高密度无线用户的情况下,RG-AP530-I将结合锐捷无线控制器智能实时的根据用户数及数据流量调整分配到不同的AP上提供接入服务,平衡接入负载压力,提高用户的平均带宽和QoS,提高连接的高可用性。
■用户无感知漫游访问通过与RG-WS系列无线控制器产品的配合,无线用户在RG-AP530-I之间移动访问时,可以保证二层网络和三层网络的无缝漫游,用户在过程中不会感觉到数据访问的中断。
■提供无线IPv6接入RG-AP530-I 全面支持IPv6特性,实现了无线网络的IPv6转发,让IPv4用户和IPv6用户都可以自动地与AC系列控制器进行隧道连接,让IPv6的应用承载在无线网络中。
全面安全防护更易用■用户级安全准入RG-AP530-I支持WEB、802.1X、MAC地址、本地认证等多种用户准入认证方式供客户选择。
不仅如此,RG-AP530-I全面支持我司GSN(Global Security Network)全局安全网络解决方案。
遵从标准的网络访问控制体系,从用户的接入、授权、主机的合规到网络行为监控、网络攻击防治等多个层面,对网络准入进行了严格的定义,并通过这种控制,实现了“入网即认证、入网即安全”的建设理念。
■灵活的虚拟AP技术通过虚拟无线接入点(Virtual AP)技术,RG-AP530-I最大可提供16个ESSID,支持16个802.1QVLAN,网管人员可以对使用相同SSID的子网或VLAN单独实施加密和隔离,并可针对每个SSID灵活的配置单独的认证方式、加密机制等。
■全面的无线安全防护配合锐捷网络一体化网管系统RG-SNC以及RG-WS系列无线控制器,RG-AP530-I具备WIDS(无线入侵检测)、射频干扰定位、流氓AP的反制、防ARP欺骗、DHCP安全保护等一系列无线安全防护功能,从根本上为用户构建真正安全可靠的无线网络。
■多种易用性认证方式支持无感知,短信和二维码访客等多种高效便捷的认证方式。
无线用户通过无感知认证方式接入网络,仅需首次输入账号和密码,避免了开机后再次输入账号密码的过程,让用户一次认证即可轻松上网。
通过短信认证方式的访客接入无线网络后会弹出认证页面,访客可以通过自己的手机号码进行注册,按照接收的短信中的账号密码进行上网操作。
二维码认证是另一种方便访客上网的方式,访客接入无线网络后,可获得二维码提示,通过被访者(员工)的授权后即可访问网络,访客行为与被访者直接关联,提供更佳安全性。
灵活的设备管理模式■胖瘦模式灵活切换RG-AP530-I 支持胖(FAT)瘦(FIT)模式的灵活切换,在FIT(瘦)模式下更能实现零配置安装使用,而完善的远程管理也大幅提高了无线网络的运维管理效率。
■Web界面管理RG-AP530-I提供AC和AP的Web管理界面,不仅轻松搞定无线配置,更能够整体运营无线网络,通过AC的Web界面不仅能够管理AP还能管理AP下联的用户,可以对用户进行限速和限制用户连入网络等行为,方便运维人员对无线的规划和运维。
■与网管软件的联动RG-AP530-I可以与锐捷网管软件SNC联动,网管软件SNC可以实现对网络中所有无线控制器和无线AP的管理,包括设备的配置备份,设备状态的查询,提供无线热敏图来显示无线AP在实际环境中的无线信号分布状态。
典型应用对于建筑结构较简单、无特殊阻挡物品、用户相对集中的场合及对容量需求较大的区域,如会议室、图书馆、教室、酒吧、休闲中心等场景宜选用此类AP设备,该类型设备可根据不同环境灵活实施分布。
RG-AP530-I的典型组网示意图:订购信息锐捷网络股份有限公司了解更多产品信息,欢迎登陆,咨询电话:400-620-8818。
*本资料产品图片及技术数据仅供参考,如有更新恕不另行通知,具体内容解释权归锐捷网络所有。