CNC机床常用普通螺纹钻孔参数表
cnc攻牙对照表【免费下载】
攻牙机是一种在机件壳体、设备端面、螺母、法兰盘等各种具有不同规格的通孔或盲孔的零件的孔的内侧面加工出内螺纹、螺丝或叫牙扣的机械加工设备。
以下我列出了cnc攻牙的对照表，攻牙机也叫攻丝机、螺纹攻牙机、螺纹攻丝机、自动攻牙机等。
根据驱动动力种类的不同攻牙机可以分为手动攻牙机、气动攻牙机、电动攻牙机、模内攻牙机和液压攻牙机等；根据攻牙机主轴数目不同可分为单轴攻牙机、二轴攻牙机、四轴攻牙机、六轴攻牙机、多轴攻牙机等；根据加工零件种类不同攻牙机又可分为模内攻牙机、万能攻牙机、热打螺母攻牙机、法兰螺母攻牙机、圆螺母攻牙机、六角螺母攻牙机、盲孔螺母攻牙机、防盗螺母攻牙机等多种型号；根据攻牙机加工过程的自动化程度不同攻牙机可分为全自动攻牙机、半自动攻牙机和手动攻牙机等；规格普通丝攻挤压丝攻底孔直径S F 底孔直径S FM1.0×0.25 0.75～0.78 120 0.25 0.86～0.88 400 0.25M1.2×0.25 0.95～0.98 150 0.25 1.06～1.08 450 0.25M1.4×0.3 1.1～1.14 210 0.3 1.24～1.25 500 0.3M1.6×0.35 1.25～1.32 280 0.35 1.41～1.43 560 0.35M1.5×0.35 1.15～1.2 250 0.35 \ 0.35 M2.0×0.4 1.6～1.68 360 0.4 1.78～1.80 600 0.4M2.5×0.45 2.1～2.14 320 0.45 2.25～2.28 550 0.45 M3.0×0.5 2.5～2.6 300 0.5 2.73～2.75 500 0.5注:1、此表参数只限铝材攻牙；2、需氧化的产品,钻孔选择最小底孔直径；3、此表只供参考，加工中应按切削液浓度与攻牙深度适当调整转数；4、此表为G95攻牙模式；5、螺旋丝攻与普通丝攻参数基本一致，攻牙时转数可加倍。
各种螺纹详细参数和钻孔直径对照表
註(1)M1.4以下等級：5H、M1.6以上等級：6H (2)基於JIS B 0209-1982標準
(2)基於JIS B 0211-1982標準
螺纹下孔径表
螺纹下孔径表
螺纹下孔径表。
螺纹下孔径表
美制管用耐密斜行螺纹(NPTF‧NPSF) (單位：
上述钻头直径來源於美制管用耐密斜行螺纹ANSI B1.20.3—1957 Dryseal Pipe Threads (Inch)標準。
螺纹下孔径表(無屑絲攻用)
螺纹下孔径表(無屑絲攻用)
螺纹下孔径表(無屑絲攻用)
螺纹下孔径表(無屑絲攻用)
螺纹下孔径表(護套螺纹用)
螺纹下孔径表(護套螺纹用)
螺纹下孔径表(護套螺纹用)
各種換算表
管用螺絲基準寸法(mm)
美制螺絲外徑公厘(mm)換算表。
机加工螺纹攻牙钻孔直径对照表
机加工螺纹攻牙钻孔直径对照表螺纹攻牙钻孔直径对照表：公制粗螺纹规格标准径2级牙钻孔径最大最小M1.0×0.250.750.7850.729M1.1×0.250.850.8850.829M1.2×0.250.950.9850.929M1.4×0.3 1.10 1.142 1.075M1.6×0.35 1.25 1.321 1.221M1.7×0.35 1.35 1.421 1.321M1.8×0.35 1.45 1.521 1.421M2.0×0.4 1.60 1.679 1.567M2.2×0.45 1.75 1.838 1.713M2.3×0.4 1.90 1.979 1.867M2.5×0.45 2.10 2.138 2.013M2.6×0.45 2.20 2.238 2.113M3.0×0.5 2.50 2.599 2.459M3.0×0.6 2.40 2.44 2.280M3.5×0.6 2.90 3.010 2.850M4.0×0.7 3.30 3.422 3.242M4.0×0.75 3.25 3.326 3.106M4.5×0.75 3.80 3.878 3.688M5.0×0.8 4.20 4.334 4.134M5.0×0.9 4.10 4.170 3.930M6.0×1.0 5.00 5.153 4.917M7.0×1.0 6.00 6.153 5.917M8.0×1.25 6.80 6.912 6.647M9.0×1.257.807.9127.647M10×1.58.508.6768.376M11×1.59.509.6769.376M12×1.7510.3010.44110.106M14×2.012.0012.21011.735M16×2.014.0014.21013.835M18×2.515.5015.74415.294M20×2.517.5017.74417.294M22×2.519.5019.74419.294M24×3.021.0021.25220.752M27×3.024.0024.25223.752M30×3.526.5026.77126.211公制细螺纹规格标准径2级牙钻孔径最大最小M1.0×0.20.800.8210.783M1.1×0.20.900.9210.883M1.2×0.2 1.00 1.0210.983M1.4×0.2 1.20 1.2210.183M1.6×0.2 1.40 1.421 1.383M1.7×0.2 1.45 1.500 1.460M1.8×0.2 1.60 1.621 1.583M2.0×0.25 1.75 1.785 1.729M2.0×0.25 1.75 1.785 1.729 M2.2×0.25 1.95 1.985 1.929 M2.3×0.25 2.05 2.061 2.001 M2.5×0.35 2.20 2.221 2.121 M2.6×0.35 2.20 2.246 2.186 M3.0×0.35 2.70 2.721 2.621 M3.5×0.35 3.20 3.221 3.121 M4.0×0.5 3.50 3.599 3.459 M4.5×0.5 4.00 4.099 3.959 M5×0.5 4.50 4.599 4.459 M5.5×0.5 5.00 5.099 4.959 M6.0×0.75 5.30 5.378 5.188 M6.0×0.5 5.50 5.550 5.400 M7.0×0.75 6.30 6.37861.88 M7.0×0.5 6.50 6.55064.00 M8.0×1.07.007.153 6.917 M8.0×0.757.307.3787.188 M8×0.57.507.5207.400 M9×1.08.008.1537.917 M9×0.758.308.3788.188 M10×1.258.808.9128.647 M10×1.09.009.1538.917 M10×0.759.309.3789.188 M10×0.59.509.5209.400 M11×1.010.0010.1539.917 M11×0.7510.3010.37810.188 M11×1.510.5010.67610.376 M12×1.2510.8010.91210.647公制细螺纹规格标准径2级牙钻孔径最大最小M12×1.011.0011.15310.917 M12×0.511.5011.52011.4M14×1.512.5012.67612.376 M14×1.013.0013.15312.917 M15×1.513.5013.67613.376 M15×1.014.0014.15313.917 M16×1.514.5014.67614.376 M16×1.015.0015.15314.917 M17×1.515.5015.67615.376 M17×1.016.0016.15315.917 M18×2.016.0016.21015.835 M18×1.516.5016.67016.376 M18×1.017.0017.15316.917 M20×2.018.0018.21017.835 M20×1.518.5018.67618.376 M20×1.019.0019.15318.917 M20×2.020.0020.21019.835 M22×1.520.5020.67620.376 M22×1.021.0021.15320.917 M24×2.022.0022.21021.835 M24×1.522.5022.67622.376 M24×1.023.0023.15322.917 M25×2.023.0023.21022.835M25×1.523.5023.67623.376M25×1.523.5023.67623.376M25×1.024.0024.15323.917M26×1.524.5024.67624.376M27×2.025.0025.21024.835M27×1.525.5025.67625.376M27×1.026.0026.15325.917M28×2.026.0026.21025.835M28×1.526.5026.67626.376M28×1.027.0027.15326.917M30×3.027.0027.25226.752M30×2.028.0028.21027.835M30×1.528.5028.67628.376M30×1.029.0029.15328.917M32×2.030.0030.21029.835M32×1.530.5030.67630.376M33×3.030.0030.25229.752M33×2.031.0031.21030.835M33×1.531.5031.37631.376M35×1.533.5033.67633.376M36×3.033.0033.25232.752M36×2.034.0034.21033.835M36×1.534.5034.67634.376美制细螺纹规格(UNF)标准径2级牙钻孔径最大最小番数牙外径NO.0-80(1.524) 1.25 1.305 1.182 NO.1-72(1.854) 1.55 1.612 1.474 NO.2-64(2.184) 1.85 1.912 1.756 NO.3-56(2.515) 2.10 2.197 2.025 NO.4-48(2.845) 2.40 2.458 2.271 NO.5-44(3.175) 2.70 2.740 2.551 NO.6-40(3.505) 2.90 3.022 2.820 NO.8-36(4.166) 3.50 3.606 3.404 NO.10-32(4.826)4.10 4.165 3.963 NO.12-28(5.846)4.60 4.724 4.496 1/4 -28 5.50 5.588 5.360 5/16 -24 6.907.035 6.782 3/8 -248.508.6368.382 7/16 -209.9010.0339.729 1/2 -2011.5011.60711.329 9/16 -1812.9013.08112.751 5/8 -1814.5014.68114.351 3/4 -1617.5014.67817.323 7/8 -1420.5020.67520.270 1 -1223.2023.57123.114 1-1/8 -1226.5026.74626.289 1-1/4 -1229.5029.92129.464 1-3/8 -1232.8033.09632.464 1-1/2 -1236.0036.27035.814无屑丝攻钻孔径规格精度等级RH4.5.6RH7.8RH9M1.0×0.250.860.88-M1.1×0.250.960.98-M1.2×0.25 1.06 1.08-M1.2×0.25 1.06 1.08-M1.4×0.3 1.24 1.25-M1.6×0.35 1.41 1.43-M1.7×0.35 1.51 1.53-M1.8×0.35 1.61 1.63-M2.0×0.4 1.78 1.80-M2.2×0.45 1.95 1.98-M2.3×0.4 2.08 2.10-M2.5×0.45 2.25 2.28-M2.6×0.45 2.35 1.38-M3.0×0.5 2.73 2.75-M3.0×0.6 3.17 3.20-M4.0×0.7 3.62 3.65 3.69M5.0×0.8 4.56 4.60 4.64M6.0×1.0 5.45 5.50 5.55M7.0×1.0 6.45 6.50 6.55M8.0×1.257.317.387.44M10×1.59.189.259.32M10×1.259.319.389.44M12×1.7511.0411.1211.21M12×1.2511.3111.3811.44美制管螺纹规格(UNEF)标准径2级牙钻孔径最大最小NO.12 -32 4.70 4.826 4.623 1/4 -32 5.60 5.690 5.486 5/16 -327.107.2647.087 3/8 -328.708.8658.661 7/16 -2810.2010.33810.135 1/2 -2811.8011.93811.709 9/16 -2813.2013.38613.132 5/8 -2414.8014.98614.732 3/4 -2017.8017.95817.678 7/8 -2021.0021.13320.853 1 -2024.0024.30824.028美制粗螺纹规格(UNC)标准径2级牙钻孔径番数牙外径最大最小NO.1-64(1.854) 1.55 1.582 1.425 NO.2-56(2.184) 1.80 1.871 1.695 NO.3-48(2.515) 2.10 2.146 1.941 NO.4-40(2.845) 2.30 2.385 2.157 NO.5-40(3.175) 2.60 2.697 2.487 NO.6-32(3.505) 2.80 2.895 2.642 NO.8-32(4.166) 3.40 3.530 3.302 NO.10-24(4.826)3.90 3.962 3.682 NO.12-24(5.846)4.50 4.597 4.344 1/4 -20 5.10 5.257 4.979 5/16 -18 6.60 6.731 6.401 3/8 -168.008.1537.987 7/16 -149.409.5009.144 1/2 -1310.8011.02310.592 9/16 -1212.2012.44611.989 5/8 -1113.6012.86813.386 3/4 -1016.2016.84016.307 7/8 -919.5019.76119.177 1 -822.2022.60621.9711 -822.2022.60621.971 1-1/8 -725.0025.34924.638 1-1/4 -728.2028.52427.813 1-3/8 -630.8031.11530.353 1-1/2 -634.0034.29033.528 1-3/4 -539.5039.82738.964 2 -4-1/245.2045.59344.679英制螺纹规格钻孔径硬材软材W1/8 - 40 2.65 2.60W5/32 - 323.25 3.20W3/16 - 243.75 3.70W1/4 - 20 5.10 5.00W5/16 - 186.60 6.50W3/8 - 168.007.90W7/16 - 149.409.30W1/2 - 1210.7010.50W9/16 - 1212.3012.00W5/8 - 1113.7013.50W3/4 - 1016.7016.50W7/8 - 919.5019.30W1 - 822.4022.00W1-1/8 - 725.0024.80W1-1/4 - 728.3028.00英制管螺纹规格标准径钻孔径最大最小PS1/16 -28 6.50 6.632 6.490PS1/8 -288.508.6378.495PS1/4 - 1911.4011.54911.341PS3/8 - 1915.0015.05414.846PS1/2 - 1418.5018.77318.489PS3/4 - 1424.0024.25923.975PS1 - 1130.2030.47130.111PS1-1/4 -1138.8039.13238.772PS1-1/2 -1144.8045.02544.665PS2 - 1156.5056.83656.476英制管螺纹规格标准径有效牙部之长度(最小)中之母螺牙内径标准长度(最小)中之母螺牙内径使用绞刀时不用绞刀时PT1/16 -28 6.10 6.2 6.244 6.384 PT1/8 -288.108.28.2498.388 PT1/4 -1910.701110.96211.174 PT3/8 -1914.2014.514.44814.658 PT1/2 -1417.601817.97918.263 PT3/4 -1423.0023.523.37823.663 Pt1 -1129.0029.529.45929.822 PT1-1/4 -1137.503837.97638.339 PT1-1/2 -1143.404443.86944.232 Pt2 -1154.9055.555.41255.844美制螺纹滚造径规格钻孔径规格钻孔径NPT NPS使用绞刀时不用绞刀时1/16 -27 6.1 6.25 6.35 1/8 -278.338.438.74 1/4 -1810.7211.1311.13 3/8 -1814.2714.2714.68 1/2 -1417.4817.8618.26 3/4 -1422.6323.0123.42 1 -11-1/228.5828.9829.36 1-1/4-11-1/237.3137.6938.1 1-1/2-11-1/243.6644.0444.45 2 -11-1/255.5855.9656.36英制螺纹滚造径规格滚造径W 3/16 - 24 4.08 - 4.05W 1/4 - 20 5.51 - 5.46W 5/16 - 187.01 - 6.95W 3/8 - 168.48 - 8.41W 7/16 - 149.92 - 9.85W 1/2 - 1211.31 - 11.24W 9/16 -1212.89 - 12.82公制螺纹规格滚造径M3.0×0.6 2.56 2.53M3.5×0.6 3.06 3.03M4.0×0.7 3.49 3.45M4.0×0.75 3.45 3.41M4.5×0.75 3.96 3.92M5.0×0.8 4.43 4.38M5.0×0.9 4.36 4.31M6.0×1.0 5.30 5.25M7.0×1.0 6.30 6.25M8.0×1.07.28 - 7.23M8.0×1.257.12 - 7.07M9.0×1.258.12 - 8.07M10×1.259.10 - 9.04M10×1.58.97 - 8.91M11×1.59.97 - 9.91M12×1.510.92 - 10.87M12×1.7510.79 - 10.73M14×2.012.63 - 12.56M16×2.014.63 - 14.56M18×2.516.31 - 16.23M20×2.518.31 - 18.23M22×2.520.31 - 20.23针车用螺纹规格(UNC)滚造径SM 1/8 40 2.735 -2.688SM 1/8 44 2.769 -2.722SM 9/64 40 3.128 -3.083SM 11/64 40 3.855 -3.805SM 3/16 32 4.205 -4.155SM 3/16 28 4.143 -4.093SM 7/32 32 5.003 -4.955SM 15/64 28 5.325 -4.955SM 1/4 40 5.890 -5.735SM 1/4 40 5.890 -5.735 SM 1/4 28 5.721 -5.366 SM 9/32 28 6.528 -6.648 SM 11/32 288.092 -8.432 SM 3/8 298.880 -8.015 SM 7/16 3010.466 -10.401 SM 7/16 1610.037 -9.967 SM 1/2 2011.819 -11.749 SM 9/16 2013.400 -13.425美制粗螺纹规格(UNC)滚造径NO.5-40 2.70 - 2.67 NO.6-32 2.95 - 2.91 NO.8-32 3.60 - 3.57 NO.10-24 4.09 - 4.05 NO.12-24 4.75 - 4.701/4 -20 5.50 - 5.455/16 -18 6.98 - 6.933/8 -168.45 - 8.407/16 -149.89 - 9.831/2 -1311.39 - 11.32 9/16 -1212.87 - 12.80美制细螺纹规格(UNF)滚造径NO.5-44 2.73 - 2.70 NO.6-40 3.05 - 3.02 NO.8-36 3.66 - 3.63 NO.10-32 4.26 - 4.80 NO.12-28 4.84 - 4.801/4 -28 5.72 - 5.685/16 -247.20 - 7.163/8 -248.79 - 8.747/16 -2010.23 - 10.18 1/2 -2011.82 - 11.76。
螺纹牙套规格及钻孔尺寸表 2
螺纹牙套纹格及纹孔尺寸表之阳早格格创做U7/16-14 4 1/27 3/810 1/413 1/816 1/8U1/2-13 4 7/87 7/81114 1/817 1/8U9/16-12 5 1/88 1/411 1/214 3/417 7/8U5/8-11 5 1/48 1/211 3/41518 3/8U3/4-10 5 7/89 3/81316 1/220 1/8U7/8-9 6 1/41013 3/417 1/221 1/4好英制细牙螺纹最小最大适用钻头1D2D3DU#8-36 3 7/8 6 1/29 1/811 5/814 1/4U#10-32 4 1/8 6 7/89 1/212 1/414 7/8U1/4-2858 1/411 3/814 1/217 5/8U5/16-24 5 1/28 7/812 1/415 5/819U3/8-24 6 7/8111519 1/823 1/8U7/16-20 6 5/810 5/814 5/818 1/222 1/2U1/2-207 7/812 3/816 7/821 3/825 7/8U5/8-18914 1/819 1/424 1/429 3/8U3/4-169 3/415 1/820 5/82631 1/2火星塞博用最小最大适用钻头10L15L20L4 5/8 6 1/29 3/413 1/8螺纹牙套做纹步调表一. 钻孔使用功具两.攻牙使用功具三.护套拆进目标四. P型工具拆进护套五. S型工具拆进六.敲断护套导舌七.使用后结构八.益坏时与出要领(以差异目标与出)问：请问怎么样采用功具？问：工具其脚段是把牙套拆进工件中，修议M6[U1/4]以下请使用Ｐ型工具，所有细牙也请使用Ｐ型工具，M6[U1/4]以上细牙Ｐ型Ｓ型两种工具多可采用.问：请问怎么样采用博用丝攻？问：牙套丝攻可分为脚攻[2收组]及板滞攻用螺旋丝攻[单收].问：为甚么所购的少度规格量起去出有敷少？问：果为牙线加进螺纹里会随螺纹线展启少，故请依规格表采用牙套.问：牙套拆出有进去母件有那几种本果？问：(A)牙套目标错了(B)使用P型工具出通过导牙端便曲交用前端锁进(C)出使用博用丝攻(D)钻孔钻大了出有自愿，里头已出螺纹[出有适用牙套].问：使用牙套机本上应注意那些事项？问：钻孔请依确定钻孔捡查是出有是有扩孔攻牙后捡查螺纹是出有是偏偏了会做用牙套功能，牙套拆进只可逆目标，出有克出有及反目标可则牙套及工具会益坏.螺纹纹套之功能螺纹护套系利用弹簧弛力之个性，将护套拆进母件螺纹内，使其螺纹啮合之能源、静力背荷均衡，故能使所有螺纹之强度减少，达到更好的锁合效验.螺纹纹套之用途板滞五金整件中，有铝、铜、铸铁、电木....等，其螺纹部位，果母材强度出有敷，常制成溃牙，螺纹护套可办理此一问题，普及产品价格.正在普遍的制制历程中，可补救过失的孔径或者益坏之牙孔，达到本规格之螺栓，脆持其产品之品量.螺纹护套适用止业，有使用螺丝之产品，皆是其对于象，比圆：汽车工业、五金制品、各式板滞、国防工业、中销产品.....等，使用螺纹护套可普及其产品价格.螺纹纹套使用材纹螺纹护套系使用下档出有锈钢SUS304弹簧线材，以热轧加工成细稀的菱形断里，再采与进步之CNC估计机博用加工机，依其规格加工成螺旋状之螺纹护套，再经恒温处理，使护套个性越发宁静出有简单金属疲倦，硬度达RC43°~50°，故使用护套之螺纹部位战淬火之钢品一般耐用，更超出普遍攻牙资料.。
螺纹钻孔尺寸
20.917 21.835 22.376 22.917 22.835 23.376 23.917 24.376 24.835 25.376 25.917 25.835 26.376 26.917 26.752 27.835 28.376 28.917 29.835 30.376 29.752 30.835 31.376 33.376 32.752 33.835 34.376
3.121 M22 1.0 3.459 M24 2.0 3.959 M24 1.5 4.459 M24 1.0 4.959 M25 2.0 5.188 M25 1.5 5.400 M25 1.0 6.188 M26 1.5 6.400 M27 2.0 6.917 M27 1.5 7.188 M27 1.0 7.400 M28 2.0 7.917 M28 1.5 8.188 M28 1.0 8.647 M30 3.0 8.917 M30 2.0 9.188 M30 1.5 9.400 M30 1.0 9.917 M32 2.0 10.188 M32 1.5 10.376 M33 3.0 10.647 M33 2.0 10.917 M33 1.5 11.400 M35 1.5 12.376 M36 3.0 12.917 M36 2.0 13.376 M36 1.5
3.221 3.599 4.099 4.599 5.099 5.378 5.550 6.378 6.550 7.153 7.378 7.520 8.153 8.378 8.921 9.153 9.378 9.520 10.153 10.378 10.676 10.912 11.153 11.520 12.676 13.153 13.676
0.80 0.90 1.00 1.20 1.40 1.45 1.60 1.75 1.95 2.05 2.20 2.20 2.70
螺纹打底孔用钻头直径尺寸表
（一）一般螺纹钻底孔用钻头直径
计算公式：
P<1mm时，D0=d-P
P>1mm时，D0=d-(1~P
式中 P——螺距（mm）
D0——攻螺纹前钻头直径（mm）
d——螺纹公称直径（mm）
工厂里的体会公式：钻孔直径＝*螺丝直径（取近式值），比如：用M8*= M8一样用的钻头就行，固然能够加大十几个司，如此好攻牙点，用7的钻头钻OK的。
粗
2
细
2
细
细
细
1
15
39
粗
4
18
粗
细
3
细
2
细
2
细
细
细
1
17
公称直径d
螺距P
钻头直径D0
公称直径d
螺距P
钻头直径D0
42
粗
48
粗
5
细
4
细
4
细
3
细
3
细
2
细
2
细
细
45
粗
52
粗
细
4
细
4
细
3
细
3
细
2
细
2
细
细
公称直径d
螺距P
钻头直径D0
公称直径d
螺距P
钻头直径D0
1
粗
20
粗
细
细
2
2
粗
细
细
细
1
19
3
粗
22
粗
细
细
2
4
粗
细
细
细
1
机加工螺纹攻牙钻孔直径对照表
机加工螺纹攻牙钻孔直径对照表螺纹攻牙钻孔直径对照表：公制粗螺纹规格标准径2级牙钻孔径最大最小M1.0×0.250.75 0.785 0.729 M1.1×0.250.85 0.885 0.829 M1.2×0.250.95 0.985 0.929 M1.4×0.3 1.10 1.142 1.075 M1.6×0.35 1.25 1.321 1.221 M1.7×0.35 1.35 1.421 1.321 M1.8×0.35 1.45 1.521 1.421 M2.0×0.4 1.60 1.679 1.567 M2.2×0.45 1.75 1.838 1.713 M2.3×0.4 1.90 1.979 1.867 M2.5×0.45 2.10 2.138 2.013 M2.6×0.45 2.20 2.238 2.113 M3.0×0.5 2.50 2.599 2.459 M3.0×0.6 2.40 2.44 2.280 M3.5×0.6 2.90 3.010 2.850 M4.0×0.7 3.30 3.422 3.242 M4.0×0.75 3.25 3.326 3.106 M4.5×0.75 3.80 3.878 3.688 M5.0×0.8 4.20 4.334 4.134 M5.0×0.9 4.10 4.170 3.930 M6.0×1.0 5.00 5.153 4.917 M7.0×1.0 6.00 6.153 5.917 M8.0×1.25 6.80 6.912 6.647 M9.0×1.257.80 7.912 7.647 M10×1.58.50 8.676 8.376 M11×1.59.50 9.676 9.376 M12×1.7510.30 10.441 10.106 M14×2.012.00 12.210 11.735 M16×2.014.00 14.210 13.835 M18×2.515.50 15.744 15.294 M20×2.517.50 17.744 17.294M22×2.519.50 19.744 19.294 M24×3.021.00 21.252 20.752 M27×3.024.00 24.252 23.752 M30×3.526.50 26.771 26.211 公制细螺纹规格标准径2级牙钻孔径最大最小M1.0×0.20.80 0.821 0.783 M1.1×0.20.90 0.921 0.883 M1.2×0.2 1.00 1.021 0.983 M1.4×0.2 1.20 1.221 0.183 M1.6×0.2 1.40 1.421 1.383 M1.7×0.2 1.45 1.500 1.460 M1.8×0.2 1.60 1.621 1.583 M2.0×0.25 1.75 1.785 1.729 M2.2×0.25 1.95 1.985 1.929 M2.3×0.25 2.05 2.061 2.001 M2.5×0.35 2.20 2.221 2.121 M2.6×0.35 2.20 2.246 2.186 M3.0×0.35 2.70 2.721 2.621 M3.5×0.35 3.20 3.221 3.121 M4.0×0.5 3.50 3.599 3.459 M4.5×0.5 4.00 4.099 3.959 M5×0.5 4.50 4.599 4.459 M5.5×0.5 5.00 5.099 4.959 M6.0×0.75 5.30 5.378 5.188 M6.0×0.5 5.50 5.550 5.400 M7.0×0.75 6.30 6.378 61.88 M7.0×0.5 6.50 6.550 64.00 M8.0×1.07.00 7.153 6.917 M8.0×0.757.30 7.378 7.188 M8×0.57.50 7.520 7.400 M9×1.08.00 8.153 7.917 M9×0.758.30 8.378 8.188 M10×1.258.80 8.912 8.647 M10×1.09.00 9.153 8.917 M10×0.759.30 9.378 9.188M11×1.010.00 10.153 9.917 M11×0.7510.30 10.378 10.188 M11×1.510.50 10.676 10.376 M12×1.2510.80 10.912 10.647 公制细螺纹规格标准径2级牙钻孔径最大最小M12×1.011.00 11.153 10.917 M12×0.511.50 11.520 11.4 M14×1.512.50 12.676 12.376 M14×1.013.00 13.153 12.917 M15×1.513.50 13.676 13.376 M15×1.014.00 14.153 13.917 M16×1.514.50 14.676 14.376 M16×1.015.00 15.153 14.917 M17×1.515.50 15.676 15.376 M17×1.016.00 16.153 15.917 M18×2.016.00 16.210 15.835 M18×1.516.50 16.670 16.376 M18×1.017.00 17.153 16.917 M20×2.018.00 18.210 17.835 M20×1.518.50 18.676 18.376 M20×1.019.00 19.153 18.917 M20×2.020.00 20.210 19.835 M22×1.520.50 20.676 20.376 M22×1.021.00 21.153 20.917 M24×2.022.00 22.210 21.835 M24×1.522.50 22.676 22.376 M24×1.023.00 23.153 22.917 M25×2.023.00 23.210 22.835 M25×1.523.50 23.676 23.376 M25×1.024.00 24.153 23.917 M26×1.524.50 24.676 24.376 M27×2.025.00 25.210 24.835 M27×1.525.50 25.676 25.376 M27×1.026.00 26.153 25.917M28×1.526.50 26.676 26.376 M28×1.027.00 27.153 26.917 M30×3.027.00 27.252 26.752 M30×2.028.00 28.210 27.835 M30×1.528.50 28.676 28.376 M30×1.029.00 29.153 28.917 M32×2.030.00 30.210 29.835 M32×1.530.50 30.676 30.376 M33×3.030.00 30.252 29.752 M33×2.031.00 31.210 30.835 M33×1.531.50 31.376 31.376 M35×1.533.50 33.676 33.376 M36×3.033.00 33.252 32.752 M36×2.034.00 34.210 33.835 M36×1.534.50 34.676 34.376 美制细螺纹规格(UNF) 标准径2级牙钻孔径最大最小番数牙外径NO.0-80(1.524) 1.25 1.305 1.182 NO.1-72(1.854) 1.55 1.612 1.474 NO.2-64(2.184) 1.85 1.912 1.756 NO.3-56(2.515) 2.10 2.197 2.025 NO.4-48(2.845) 2.40 2.458 2.271 NO.5-44(3.175) 2.70 2.740 2.551 NO.6-40(3.505) 2.90 3.022 2.820 NO.8-36(4.166) 3.50 3.606 3.404 NO.10-32(4.826) 4.10 4.165 3.963 NO.12-28(5.846) 4.60 4.724 4.496 1/4 -28 5.50 5.588 5.360 5/16 -24 6.90 7.035 6.782 3/8 -24 8.50 8.636 8.382 7/16 -20 9.90 10.033 9.729 1/2 -20 11.50 11.607 11.329 9/16 -18 12.90 13.081 12.751 5/8 -18 14.50 14.681 14.3513/4 -16 17.50 14.678 17.323 7/8 -14 20.50 20.675 20.270 1 -12 23.20 23.571 23.114 1-1/8 -12 26.50 26.746 26.289 1-1/4 -12 29.50 29.921 29.464 1-3/8 -12 32.80 33.096 32.464 1-1/2 -12 36.00 36.270 35.814 无屑丝攻钻孔径规格精度等级RH4.5.6 RH7.8 RH9M1.0×0.250.86 0.88 -M1.1×0.250.96 0.98 -M1.2×0.25 1.06 1.08 -M1.4×0.3 1.24 1.25 -M1.6×0.35 1.41 1.43 -M1.7×0.35 1.51 1.53 -M1.8×0.35 1.61 1.63 -M2.0×0.4 1.78 1.80 -M2.2×0.45 1.95 1.98 -M2.3×0.4 2.08 2.10 -M2.5×0.45 2.25 2.28 -M2.6×0.45 2.35 1.38 -M3.0×0.5 2.73 2.75 -M3.0×0.6 3.17 3.20 -M4.0×0.7 3.62 3.65 3.69 M5.0×0.8 4.56 4.60 4.64 M6.0×1.0 5.45 5.50 5.55 M7.0×1.0 6.45 6.50 6.55 M8.0×1.257.31 7.38 7.44 M10×1.59.18 9.25 9.32 M10×1.259.31 9.38 9.44 M12×1.7511.04 11.12 11.21 M12×1.2511.31 11.38 11.44 美制管螺纹规格(UNEF) 标准径2级牙钻孔径最大最小NO.12 -32 4.70 4.826 4.6231/4 -32 5.60 5.690 5.486 5/16 -32 7.10 7.264 7.087 3/8 -32 8.70 8.865 8.661 7/16 -28 10.20 10.338 10.135 1/2 -28 11.80 11.938 11.709 9/16 -28 13.20 13.386 13.132 5/8 -24 14.80 14.986 14.732 3/4 -20 17.80 17.958 17.678 7/8 -20 21.00 21.133 20.853 1 -20 24.00 24.308 24.028 美制粗螺纹规格(UNC) 标准径2级牙钻孔径番数牙外径最大最小NO.1-64(1.854) 1.55 1.582 1.425 NO.2-56(2.184) 1.80 1.871 1.695 NO.3-48(2.515) 2.10 2.146 1.941 NO.4-40(2.845) 2.30 2.385 2.157 NO.5-40(3.175) 2.60 2.697 2.487 NO.6-32(3.505) 2.80 2.895 2.642 NO.8-32(4.166) 3.40 3.530 3.302 NO.10-24(4.826) 3.90 3.962 3.682 NO.12-24(5.846) 4.50 4.597 4.344 1/4 -20 5.10 5.257 4.979 5/16 -18 6.60 6.731 6.401 3/8 -16 8.00 8.153 7.987 7/16 -14 9.40 9.500 9.144 1/2 -13 10.80 11.023 10.592 9/16 -12 12.20 12.446 11.989 5/8 -11 13.60 12.868 13.386 3/4 -10 16.20 16.840 16.307 7/8 -9 19.50 19.761 19.177 1 -8 22.20 22.606 21.971 1-1/8 -7 25.00 25.349 24.638 1-1/4 -7 28.20 28.524 27.813 1-3/8 -6 30.80 31.115 30.353 1-1/2 -6 34.00 34.290 33.528 1-3/4 -5 39.50 39.827 38.9642 -4-1/2 45.20 45.593 44.679 英制螺纹规格钻孔径硬材软材W1/8 - 40 2.65 2.60W5/32 - 32 3.25 3.20W3/16 - 24 3.75 3.70W1/4 - 20 5.10 5.00W5/16 - 18 6.60 6.50W3/8 - 16 8.00 7.90W7/16 - 14 9.40 9.30W1/2 - 12 10.70 10.50W9/16 - 12 12.30 12.00W5/8 - 11 13.70 13.50W3/4 - 10 16.70 16.50W7/8 - 9 19.50 19.30W1 - 8 22.40 22.00W1-1/8 - 7 25.00 24.80W1-1/4 - 7 28.30 28.00英制管螺纹规格标准径钻孔径最大最小PS1/16 -28 6.50 6.632 6.490PS1/8 -28 8.50 8.637 8.495PS1/4 - 19 11.40 11.549 11.341PS3/8 - 19 15.00 15.054 14.846PS1/2 - 14 18.50 18.773 18.489PS3/4 - 14 24.00 24.259 23.975PS1 - 11 30.20 30.471 30.111PS1-1/4 -11 38.80 39.132 38.772PS1-1/2 -11 44.80 45.025 44.665PS2 - 11 56.50 56.836 56.476英制管螺纹规格标准径有效牙部之长度(最小)中之母螺牙内径标准长度(最小)中之母螺牙内径使用绞刀时不用绞刀时PT1/16 -28 6.10 6.2 6.244 6.384 PT1/8 -28 8.10 8.2 8.249 8.388 PT1/4 -19 10.70 11 10.962 11.174 PT3/8 -19 14.20 14.5 14.448 14.658 PT1/2 -14 17.60 18 17.979 18.263 PT3/4 -14 23.00 23.5 23.378 23.663 Pt1 -11 29.00 29.5 29.459 29.822 PT1-1/4 -11 37.50 38 37.976 38.339 PT1-1/2 -11 43.40 44 43.869 44.232 Pt2 -11 54.90 55.5 55.412 55.844 美制螺纹滚造径规格钻孔径NPT NPS使用绞刀时不用绞刀时1/16 -27 6.1 6.25 6.351/8 -27 8.33 8.43 8.741/4 -18 10.72 11.13 11.133/8 -18 14.27 14.27 14.681/2 -14 17.48 17.86 18.263/4 -14 22.63 23.01 23.421 -11-1/2 28.58 28.98 29.361-1/4-11-1/2 37.31 37.69 38.11-1/2-11-1/2 43.66 44.04 44.452 -11-1/2 55.58 55.96 56.36英制螺纹滚造径规格滚造径W 3/16 - 24 4.08 - 4.05W 1/4 - 20 5.51 - 5.46W 5/16 - 18 7.01 - 6.95W 3/8 - 16 8.48 - 8.41W 7/16 - 14 9.92 - 9.85W 1/2 - 12 11.31 - 11.24W 9/16 -12 12.89 - 12.82公制螺纹规格滚造径M3.0×0.6 2.56 2.53M3.5×0.6 3.06 3.03M4.0×0.7 3.49 3.45M4.0×0.75 3.45 3.41M4.5×0.75 3.96 3.92M5.0×0.8 4.43 4.38M5.0×0.9 4.36 4.31M6.0×1.0 5.30 5.25M7.0×1.0 6.30 6.25M8.0×1.07.28 - 7.23M8.0×1.257.12 - 7.07M9.0×1.258.12 - 8.07M10×1.259.10 - 9.04M10×1.58.97 - 8.91M11×1.59.97 - 9.91M12×1.510.92 - 10.87 M12×1.7510.79 - 10.73 M14×2.012.63 - 12.56 M16×2.014.63 - 14.56 M18×2.516.31 - 16.23 M20×2.518.31 - 18.23 M22×2.520.31 - 20.23 针车用螺纹规格(UNC) 滚造径SM 1/8 40 2.735 -2.688 SM 1/8 44 2.769 -2.722 SM 9/64 40 3.128 -3.083 SM 11/64 40 3.855 -3.805 SM 3/16 32 4.205 -4.155 SM 3/16 28 4.143 -4.093 SM 7/32 32 5.003 -4.955 SM 15/64 28 5.325 -4.955 SM 1/4 40 5.890 -5.735 SM 1/4 28 5.721 -5.366 SM 9/32 28 6.528 -6.648 SM 11/32 28 8.092 -8.432 SM 3/8 29 8.880 -8.015 SM 7/16 30 10.466 -10.401 SM 7/16 16 10.037 -9.967SM 1/2 20 11.819 -11.749 SM 9/16 20 13.400 -13.425 美制粗螺纹规格(UNC) 滚造径NO.5-40 2.70 - 2.67 NO.6-32 2.95 - 2.91 NO.8-32 3.60 - 3.57 NO.10-24 4.09 - 4.05 NO.12-24 4.75 - 4.701/4 -20 5.50 - 5.455/16 -18 6.98 - 6.933/8 -16 8.45 - 8.407/16 -14 9.89 - 9.831/2 -13 11.39 - 11.32 9/16 -12 12.87 - 12.80 美制细螺纹规格(UNF) 滚造径NO.5-44 2.73 - 2.70 NO.6-40 3.05 - 3.02 NO.8-36 3.66 - 3.63 NO.10-32 4.26 - 4.80 NO.12-28 4.84 - 4.801/4 -28 5.72 - 5.685/16 -24 7.20 - 7.163/8 -24 8.79 - 8.747/16 -20 10.23 - 10.18 1/2 -20 11.82 - 11.76。
各种螺纹参数和钻孔直径对照表
螺纹下孔径表公制粗牙螺纹JIS B 0209-1982(單位：mm)螺纹尺寸钻头直径崁合度區分：中(注1)2級(注2)下孔径崁合度區分：中(註1)2級(註2)內螺纹小径最小直径最大直径M1× 0.25 0.75 0.78 (80%) 0.729 0.7851.1 × 0.25 0.85 0.88 (80%) 0.829 0.8851.2 × 0.25 0.95 0.98 (80%) 0.929 0.9851.4 × 0.3 1.1 1.14 (80%) 1.075 1.1421.6 × 0.35 1.25 1.32 (75%) 1.221 1.3211.8 × 0.35 1.45 1.52 (75%) 1.421 1.5212× 0.4 1.6 1.65 (80%) 1.567 1.6792.2 × 0.45 1.75 1.83 (75%) 1.713 1.8382.5 × 0.45 2.1 2.13 (75%) 2.013 2.1383× 0.5 2.5 2.59 (75%) 2.459 2.5993.5 × 0.6 2.9 3.01 (75%) 2.850 3.0104× 0.7 3.3 3.39 (80%) 3.242 3.4224.5 × 0.75 3.8 3.85 (80%) 3.688 3.8785× 0.8 4.2 4.31 (80%) 4.134 4.334 6× 1 5 5.13 (80%) 4.917 5.153 7× 1 6 6.13 (80%) 5.917 6.153 8× 1.25 6.8 6.85 (85%) 6.647 6.912 9× 1.25 7.8 7.85 (85%) 7.647 7.912 10× 1.5 8.5 8.62 (85%) 8.376 8.676 11× 1.5 9.5 9.62 (85%) 9.376 9.676 12× 1.75 10.3 10.40 (85%) 10.106 10.441 14× 2 12 12.2 (85%) 11.835 12.210 16× 2 14 14.2 (85%) 13.835 14.210 18× 2.5 15.5 15.7 (85%) 15.294 15.744 20× 2.5 17.5 17.7 (85%) 17.294 17.744 22× 2.5 19.5 19.2 (85%) 19.294 19.744 24× 3 21 21.2 (85%) 20.752 21.252 27× 3 24 24.2 (85%) 23.752 24.252 30× 3.5 26.5 26.6 (90%) 26.211 26.771 33× 3.5 29.5 29.6 (90%) 29.211 29.771 36× 4 32 32.1 (90%) 31.670 32.27039 × 4 35 35.1 (90%) 34.670 35.27042 × 4.5 37.5 37.6 (90%) 37.129 37.79945 × 4.5 40.5 40.6 (90%) 40.129 40.79948 × 5 43 43.1 (90%) 42.587 43.297 註(1)M1.4以下等級：5H、M1.6以上等級：6H(2)基於JIS B 0209-1982標準螺纹下孔径表公制細牙螺纹JIS B 0211-1982(單位：mm)螺纹尺寸钻头直径崁合度區分：中(注1)2級(注2)下孔径崁合度區分：中(註1)2級(註2)內螺纹小径最小直径最大直径M2.5 × 0.35 2.2 2.22 (75%) 2.121 2.221 3× 0.35 2.7 2.72 (75%) 2.621 2.7213.5 × 0.35 3.2 3.22 (75%) 3.121 3.2214× 0.5 3.5 3.59 (75%) 3.459 3.5994.5 × 0.5 4 4.09 (75%) 3.959 4.0995× 0.5 4.5 4.59 (75%) 4.459 4.5995.5 × 0.5 5 5.09 (75%) 4.959 5.0996× 0.75 5.3 5.35 (80%) 5.188 5.378 7× 0.75 6.3 6.35 (80%) 6.188 6.378 8× 1 7 7.13 (80%) 6.917 7.153 8× 0.75 7.3 7.35 (80%) 7.188 7.378 9× 1 8 8.13 (80%) 7.917 8.153 9× 0.75 8.3 8.35 (80%) 8.188 8.378 10× 1.25 8.8 8.85 (85%) 8.647 8.912 10× 1 9 9.13 (80%) 8.917 9.153 10× 0.75 9.3 9.35 (80%) 9.188 9.378 11 × 1 10 10.13 (80%) 9.917 10.15311 × 0.75 10.3 10.35 (80%) 10.188 10.37812 × 1.5 10.5 10.62 (85%) 10.376 10.676 12 × 1.25 10.8 10.85 (85%) 10.647 10.912 12 × 1 11 11.13 (80%) 10.917 11.153 14 × 1.5 12.5 12.62 (85%) 12.376 12.67614 × 1 13 13.13 (80%) 12.917 13.15315 × 1.5 13.5 13.62 (85%) 13.376 13.67615 × 1 14 14.13 (80%) 13.917 14.15316 × 1.5 14.5 14.62 (85%) 14.376 14.67616 × 1 15 15.13 (80%) 14.917 15.15317 × 1.5 15.5 15.62 (85%) 15.376 15.67617 × 1 16 16.13 (80%) 15.917 16.15318 × 2 16 16.2 (85%) 15.835 16.210 18 × 1.5 16.5 16.62 (85%) 16.376 16.676 18 × 1 17 17.13 (80%) 16.917 17.153 20 × 2 18 18.2 (85%) 17.835 18.210 20 × 1.5 18.5 18.62 (85%) 18.376 18.67622 × 2 20 20.2 (85%) 19.835 20.21022 × 1.5 20.5 20.62 (85%) 20.376 20.67622 × 1 21 21.13 (80%) 20.917 21.15324 × 2 22 22.2 (85%) 21.835 22.21024 × 1.5 22.5 22.62 (85%) 22.376 22.67624 × 1 23 23.13 (80%) 22.917 23.15325 × 2 23 23.2 (85%) 22.835 23.21025 × 1.5 23.5 23.62 (85%) 23.376 23.67625 × 1 24 24.13 (80%) 23.917 24.153螺纹下孔径表公制細牙螺纹JIS B 0211-1982(單位：mm)螺纹尺寸钻头直径崁合度區分：中(注1)2級(注2)下孔径崁合度區分：中(註1)2級(註2)內螺纹小径最小直径最大直径M26 × 1.5 24.5 24.62 (85%) 24.376 24.67627 × 2 25 25.2(85%) 24.835 25.21027 × 1.5 25.5 25.62 (85%) 25.376 25.67627 × 1 26 26.13 (80%) 25.917 26.15328 × 2 26 26.2(85%) 25.835 26.21028 × 1.5 26.5 26.62 (85%) 26.376 26.67628 × 1 27 27.13 (80%) 26.917 27.15330 × 3 27 27.2 (85%) 26.752 27.25230 × 2 28 28.2 (85%) 27.835 28.21030 × 1.5 28.5 28.62 (85%) 28.376 28.67630 × 1 29 29.13 (80%) 28.917 29.15332 × 2 30 30.2 (85%) 29.835 30.21032 × 1.5 30.5 30.62 (85%) 30.376 30.67633 × 3 30 30.2 (85%) 29.752 30.25233 × 2 31 31.2 (85%) 30.835 31.21033 × 1.5 31.5 31.62 (85%) 31.376 31.67635 × 1.5 33.5 33.62 (85%) 33.376 33.67636 × 3 33 33.2 (85%) 32.752 33.25236 × 2 34 34.2 (85%) 33.835 34.21036 × 1.5 34.5 34.62 (85%) 34.376 34.67638 × 1.5 36.5 36.62 (85%) 36.376 36.67639 × 3 36 36.2 (85%) 35.752 36.25239 × 2 37 37.2 (85%) 36.835 37.21039 × 1.5 37.5 37.62 (85%) 37.376 37.67640 × 3 37 37.2 (85%) 36.752 37.25240 × 2 38 38.2 (85%) 37.835 38.21040 × 1.5 38.5 38.62 (85%) 38.376 38.67642 × 4 38 38.1 (90%) 37.670 38.27042 × 3 39 39.2 (85%) 38.752 39.25242 × 1.5 40.5 40.62 (85%) 40.376 40.676 45 × 4 41 41.1 (90%) 40.670 41.270 45 × 3 42 42.2 (85%) 41.752 42.252 45 × 2 43 43.2 (85%) 42.835 43.210 45 × 1.5 43.5 43.62 (85%) 43.376 43.676 48 × 4 44 44.1 (90%) 43.670 44.270 48 × 3 45 45.2 (85%) 44.752 45.25248 × 2 46 46.2 (85%)45.835 46.21048 × 1.5 46.5 46.62 (85%) 46.376 46.67650 × 3 47 47.2 (85%) 46.752 47.25250 × 2 48 48.2 (85%) 47.835 48.21050 × 1.5 48.5 48.62 (85%) 48.376 48.676註(1)等級：6H(2)基於JIS B 0211-1982標準螺纹下孔径表美制粗牙螺纹(單位：mm)螺纹尺寸钻头直径2B級螺纹下孔径內螺纹小径最小直径最大直径NO.1 -64UNC 1.55 1.57 (65%) 1.425 1.5822 -56 1.8 1.86 (65%) 1.695 1.8713 -48 2.1 2.14 (65%) 1.941 2.1464 -40 2.3 2.36 (70%) 2.157 2.3855 -40 2.6 2.69 (70%) 2.487 2.6976 -32 2.8 2.86 (75%) 2.642 2.8958 -32 3.4 3.52 (75%) 3.302 3.53010 -24 3.9 3.91 (80%) 3.683 3.96212 -24 4.5 4.57 (80%) 4.344 4.5971/4-20 5.1 5.25 (80%) 4.979 5.257 5/16-18 6.6 6.72 (80%) 6.401 6.731 3/8-16 8 8.15 (80%) 7.798 8.153 7/16 -14 9.4 9.50 (80%) 9.144 9.550 1/2-13 10.8 11.0 (80%) 10.592 11.023 9/16 -12 12.2 12.3 (85%) 11.989 12.446 5/8-11 13.6 13.8 (85%) 13.386 13.868 3/4-10 16.5 16.8 (80%) 16.307 16.840 7/8-9 19.5 19.6 (85%) 19.177 19.7611 -8 22.2 22.5 (85%) 21.971 22.60611/8 -7 25 25.2 (85%) 24.638 25.349 11/4 -7 28.2 28.4 (85%) 27.813 28.524 13/8 -6 30.8 31.0 (85%) 30.353 31.115 11/2 -6 34 34.2 (85%) 33.528 34.290 13/4 -5 39.5 39.8 (85%) 38.964 39.8272 - 4 45.2 45.3 (90%) 44.679 45.593螺纹下孔径表美制細牙螺纹(單位：mm)螺纹尺寸钻头直径2B級螺纹下孔径內螺纹小径最小直径最大直径NO.0-80UNF1.25 1.30 (65%) 1.182 1.3051 -72 1.55 1.61 (65%) 1.474 1.6122 -64 1.85 1.90 (65%) 1.756 1.9123 -56 2.1 2.17 (70%) 2.025 2.1974 -48 2.4 2.44 (70%) 2.271 2.4585 -44 2.7 2.74 (70%) 2.551 2.7406 -40 2.9 3.02 (70%) 2.820 3.0228 -36 3.5 3.59 (75%) 3.404 3.60610 -32 4.1 4.14 (80%) 3.963 4.16512 -28 4.6 4.70 (80%) 4.496 4.7241/4-28 5.5 5.56 (80%) 5.360 5.5885/16-24 6.9 7.02 (80%) 6.782 7.035 3/8-24 8.5 8.61 (80%) 8.382 8.6367/16-20 9.9 10.01 (80%) 9.729 10.033 1/2-20 11.5 11.60 (80%) 11.329 11.6079/16-18 12.9 13.07 (80%) 12.751 13.081 5/8-18 14.5 14.65 (80%) 14.351 14.681 3/4-16 17.5 17.59 (85%) 17.323 17.678 7/8-14 20.5 20.6(85%) 20.270 20.675 1-12 23.2 23.5(85%) 23.114 23.5711 1/8 -12 26.5 26.7(80%) 26.289 26.7461 1/4 -12 29.5 29.9(80%) 29.464 29.9211 3/8 -12 32.8 33.0(85%) 32.639 33.0961 1/2 -12 36 36.2(85%) 35.814 36.271螺纹下孔径表英制粗牙螺纹(單位：mm)螺纹尺寸下孔径嵌合率A列(硬材質) B列(軟材質) A列直径B列直径內螺纹最小径內螺纹最大径W 1/8 2.6 2.5 70.7 83.0 70.0 88.3 3/16 3.7 3.6 78.4 85.8 70.0 88.3 1/4 5.1 5.0 76.9 83.0 70.5 88.3 5/16 6.6 6.5 74.0 99.5 70.1 88.4 3/8 8.0 7.9 75.0 80.0 69.5 88.2 7/16 9.4 9.3 73.7 80.0 69.0 88.81/2 10.7 10.5 73.8 81.2 69.0 88.29/16 12.3 12.0 73.4 84.4 69.0 88.25/8 13.7 13.5 73.5 80.3 69.6 88.53/4 16.7 16.5 72.3 78.4 69.6 88.37/8 19.5 19.3 75.4 80.9 70.1 88.41 22.4 22.0 73.8 83.6 71.0 88.21 1/825.0 24.8 76.9 81.3 72.0 88.41 1/428.3 28.0 74.3 80.7 72.0 88.41 3/830.5 30.3 81.6 85.3 73.8 88.61 1/233.8 33.5 79.3 84.8 73.8 88.61 5/836.0 35.7 81.1 85.7 74.8 88.31 3/439.2 39.0 80.7 83.8 74.8 88.31 7/841.8 41.5 80.6 84.7 74.7 88.42 45.0 44.7 80.2 84.4 74.7 88.4螺纹下孔径表英制管用螺纹(單位：mm)管用螺纹尺寸JIS B 0203 JIS B 2301 錐管內螺纹Rc(PT) 平行內螺纹Rp(PS) 錐管內螺纹計算值下孔径計算值下孔径計算值下孔径1/16 6.230 6.2 6.490 6.5 －－1/8 8.235 8.2 8.495 8.5 8.191 8.2 1/4 10.941 10.9 11.341 11.4 10.945 10.9 3/8 14.428 14.4 14.846 14.9 14.388 14.4 1/2 17.950 18 18.489 18.5 17.943 18 3/4 23.349 23 23.975 24 23.305 23 1 29.423 29 30.111 30 29.353 29 1 1/437.940 38 38.772 39 37.890 381 1/243.833 44 44.565 45 43.720 432 55.412 55 56.476 56 55.406 552 1/270.701 71 72.009 72 70.788 703 83.201 83 84.709 85 83.364 833 1/295.547 96 97.155 97 95.747 954 107.834 108 109.855 110 108.322 1085 133.110 133 135.255 135 133.597 1336 158.510 159 160.655 161 158.810 1587 183.360 183 185.954 1868 208.560 209 211.354 2129 233.960 234 236.754 23710 259.166 259 262.154 26212 309.747 310 312.875 313螺纹下孔径表英制平行管用螺纹PF(G) (單位：mm) 螺纹下孔径內螺纹小径(參考)尺寸大径標準嵌合高度H系列100 95 90 85 80 75 70 65 60 最小直径最大直径G 1/16 7.723 0.5808 6.56 6.62 6.68 6.74 6.79 6.85 6.91 6.97 7.03 6.843 6.561 G(PF)1/8 9.728 〞8.57 8.62 8.68 8.74 8.80 8.86 8.92 8.97 9.03 8.848 8.566 1/4 13.157 0.8560 11.53 11.62 11.70 11.79 11.87 11.96 12.04 12.13 11.890 11.445 3/8 16.662 〞14.95 15.04 15.12 15.21 15.29 15.38 15.46 15.55 15.64 15.395 14.950 1/2 20.955 1.1618 18.8 18.9 19.0 19.1 19.2 19.3 19.4 19.6 19.172 18.631 5/8 22.911 〞20.6 20.7 20.8 20.9 21.0 21.2 21.3 21.4 21.5 21.130 20.589 3/4 26.441 〞24.2 24.4 24.5 24.6 24.7 24.8 24.9 25.0 24.658 24.117 7/8 30.201 〞27.9 28.0 28.1 28.2 28.3 38.5 28.6 28.7 28.8 28.418 27.877 1 33.249 14.786 30.3 30.4 30.6 30.7 30.9 31.0 31.2 31.3 31.5 30.931 30.2911 1/837.897 〞35.1 35.2 35.4 35.5 35.7 35.8 35.9 36.5 35.579 34.939 1 1/441.910 〞39.0 39.1 39.2 39.4 39.6 39.7 39.8 40.0 40.1 39.592 38.952 1 3/844.323 〞41.4 41.5 41.7 41.8 42.0 42.1 42.2 42.4 42.6 42.005 41.3651 1/247.803 〞45.0 45.1 45.3 45.4 45.6 45.7 45.9 46.0 45.485 49.0231 5/851.910 〞49.2 49.3 49.5 49.6 49.8 49.9 50.0 50.2 49.672 50.7881 3/453.746 〞50.8 50.9 51.1 51.2 51.4 51.5 51.7 52.0 52.0 51.428 56.6562 59.614 〞56.8 57.0 57.1 57.2 57.4 57.5 57.8 57.8 57.296使用粗線左側數據作為攻絲前的底孔直径，可加工符合JIS B 0202的A級或B級的內螺纹小径。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
4、孔加工循环的高度平面选择：a:Z向R高度：对G81、G82，为螺纹孔上表面以上3-5mm,对G84应大些，为10mm以上。
b:初始平面高度：为螺纹孔上表面以上20mm。公司选用100mm。
5、孔底面高度：对底孔钻，考虑到钻头角度以及孔是通孔的因素，取螺纹孔下表面下方0.3D底孔。
注：若攻不通孔螺纹，底孔深度：D钻=h有效+0.7D+0.3D底孔。
6、对钻头加工倒角，大小采用估算法，手轮进给倒角，切削一定深度后，退出游标卡尺测量，一般比螺纹孔径大3-4mm。
7、对丝锥：因为孔加工刀具对刀时是以钻尖或丝锥端中心为刀位点，攻螺纹时，由于丝锥切削部分有锥角，端部不能切出完整的牙型， 丝锥钻入深度应大于螺纹有效深度。一般可取：H丝=h有效+0.7D。D为螺纹大径。 8、中心钻应短，有良好的刚度。
180
500
500
NPT1/8″
8.7 14
700
180
加工过程：
1、先铣削上表面，再加工螺纹，若表面无要求，则可不铣面。
2、加工螺纹的方法:先用中心钻加工底孔的中心孔，再钻底孔，然后对底孔倒角，最后攻丝。
公司为提高效率，在点孔时，点的稍大些，连倒角一起做了。
3、孔加工循环的选择，中心钻选用G82,底孔加工选用G81，倒角选用G82，螺纹若是右旋，选用G84。
M16×2
13.9 9（23） 460
220
400
800 M20×1.5 18.5
M20×2.5 17.4 10（24） 365
180
320
800 M20×1.5 18.5
M24×3
21 11（25）Байду номын сангаас340
160
250
750
M30X3.5
26.5
250
125
200
700
M10×1
9 12（26） 700
普通螺纹
M4×0.7 M5×0.8 M6×1 M8×1.25
M10×1.5
CNC机床常用普通螺纹钻孔参数表
底孔 刀号 钻头转速 钻头进给 丝锥转速 丝锥进给
3.3 3
950
90
4.2 4
900
90
445
356
5 5（19） 850
180
425
425
6.7 6（20） 800
200
500
625
细螺纹
底孔直径
通用管螺 纹
1/4″ 2/8″ 1/2″ 3/4″
底孔直径
11.5 15
18.7 24.2
钻头转速
600 430 340 270
钻头进给
160 120 100 150
8.5 7（21） 700
300
500
750 M12×1.25 10.7
M12×1.75 10.2 8（22） 630
280
500
875 M16×1.5 14.5