常用的焊接名词中英文对照表
常用焊接术语中英文对照
常用焊接术语中英文对照焊接Welding10.1 焊接种类Varieties of Welding电弧焊arc welding电熔焊electric fusion welding (EFW)气熔焊fusion gas welding (FGW)电阻焊electric resistance welding (ERW)有保护的金属电弧焊shielded metal arc welding (SMAW)手工或自动隋性气体保护钨极电弧焊manual and automatic inert gas tungsten arc welding (GTAW)自动埋弧焊automatic submerged arc welding金属极隋性气体保护电弧焊gas metal arc weiding (GMAW)氩弧焊argon-arc welding，气体保护电弧焊gas-shielded arc welding气焊gas welding; flame welding等离子焊plasma welding硬钎焊braze welding电渣焊electroslag welding爆炸焊explosive welding10.2 焊接形式Type of Welding角焊fillet welding间断焊intermittent welding点焊spot welding对焊butt welding搭焊lap welding塞焊plug welding珠焊bead welding槽焊slot welding堆焊build up welding垫板焊backing weld坡口grooveV形坡口V groove单面U形坡口single U grooveK形坡口double bevel grooveX形坡口double V groove双面U形坡口double U grooveU-V组合坡口combination U and V groove根部间隙root gap焊接符号symbol of weld错边量alignment tolerance10.3 焊接位置Welding Position仰焊overhead welding现场焊field weld (F.W.)封底焊back run welding立焊vertical welding平焊flat welding工厂（车间）焊接shop weld定位焊tack weld跳焊skip welding节距pitch10.4 焊接缺陷Defects of Welding焊接裂纹weld crack根部裂纹root crack微裂纹micro crack错位mismatch弧坑pit; crater焊穿burn through夹渣slag inclusion咬边；咬肉undercut焊瘤overlap气孔porosity, blow hole砂眼blister针孔pin hole严重飞溅excessive spatter未溶合incomplete fusion; lack of fusion 根部未焊透incomplete penetration10.5 其它母材；基层金属base metal预热preheating热影响区heat affected zone (HAZ)焊条welding electrode (rod)焊丝welding wire焊药（剂）flux。
常用的焊接名词中英文对照表
7
焊接工艺
Welding Technology (Welding Procedure)
8
焊接操作
Welding Operation
9
焊接顺序
Welding Sequence
10
熔敷顺序
Build-up Sequence
11
焊接方向
Direction of Welding
12
焊接位置
Position of Welding
常用的焊接名词中英文对照表
注：圆括号内为同义词，方括号内为可省略。
序号
焊接名词（中文）
焊接名词（英文）
1
焊接
Welding
2
熔焊
Fusion Welding
3
压焊
Pressure Welding
4
钎焊
Brazing and Soldering
5
焊接过程
Welding Process
6
焊接技术
Welding Technique
55
焊后热处理
Postweld Heat Treatment
56
预热温度
Preheat Temperature
57
后热温度
Postheating Temperature
58
层间温度
Interpass Temperature
59
焊丝伸出长度
Wire Extention
60
弧长
Arc Length
61
熔化速度
13
焊缝倾角
Weld Slope (Inclination of Weld Axis)
14
焊接名词中英文对照，看懂外国图纸分分钟搞定
焊接名词中英⽂对照，看懂外国图纸分分钟搞定当前浏览器不⽀持播放⾳乐或语⾳，请在微信或其他浏览器中播放⼭沟沟⾦志⽂ - 中国好声⾳第⼀季第13期弧光闪耀⼈⽣，⽕花飞出精彩！焊接路上家园伴你同⾏！焊⼯：你⽼婆喊你回家吃饭！Mechanical tests ⼒学性能试验Tension tests 拉伸试验Tensile specimen 拉伸试样Bend tests 弯曲试验Face bend ⾯弯Root bend 背弯Side bend 側弯Notch toughness tests 缺⼝韧性试验Hammer tests 錘击试验Peening 錘击Torque tests 扭曲试验Carbon steels 碳钢Alloy steels 合⾦钢Stainless steels 不锈钢Welding process 焊接⽅法Gas tungsten –arc welding(GTAW)(TIG) 钨极⽓体保护焊Shielded metal –arc welding (SMAW) ⼿⼯电弧焊Submerged – arc welding (SAW) 埋弧焊Plug weld 塞焊Surfacing weld 堆焊Weld metal overlay 堆焊层Stud welding 螺柱焊Metal –arc welding(GMAW)(MIG) 熔化极⽓体保护焊Plasma – arc welding (PAW) 等离⼦弧焊Electroslag welding (ESW) 电渣焊Electron beam welding (EBW) 电⼦束焊Friction welding (FRC) 摩擦焊Induction welding (IW) 感应焊Laser beam welding (LBW) 激光焊Resistance welding (RW) 电阻焊Resistance spot welding (RSW) 电阻点焊Oxyfuel gas welding (OFW) 氧—燃料⽓焊Oxyfuel gas cutting (OFC) 氧—燃料⽓割Backhand welding 右焊法Forehand welding 左焊法Post weld heat treatment(PWHT)焊后热处理Postheating 后热Preheating 预热Interpass temperature 层间温度Sorbite 索⽒体Bainite 贝⽒体Anneal (annealing) 退⽕ (缓冷)Temper(drawing) 回⽕Reduction 还原Cooling 冷却Temper brittleness 回⽕脆性Low –temperature brittleness 冷脆性Hardening 淬⽕Modified treatment 调质处理Crystal lattice 晶格Crystal nucleus 晶核Crystal (grain) 晶粒Grain boundary 晶界Crystallize 结晶Recrystal 重结晶Brazing 钎接Brazing filler metal 钎料Specimens 试样Sectioning test 切⽚试验Trimming 清理焊缝Cast iron 铸铁Nodular iron 球墨铸铁Pig iron ⽣铁Wrought iron 熟铁Moulded steel 铸钢Impact toughness 冲击韧性Austempering 等温淬⽕Fracture 断⼝Fracture surface 折断⾯Positions of welds 焊接位置Pipe 管⼦Fixed horizontal (5G) ⽔平固定Fixed vertical (2G) 垂直固定Fixed pipe on 45°(6G) 45度固定Plate 板材Flat (F)(1G) 平焊Horizontal (H)(2G) 横焊Vertical(V)（3G）⽴焊Overhead (O)(4G) 仰焊Butt joint 对接接头Tee joint 丁字接头Lap joint 搭接接头Corner joint ⾓接接头Joint design 接头型式Square groove Ⅰ型坡⼝Single –vee groove V型坡⼝Single –U groove U型坡⼝Double –U groove 双⾯U型坡⼝Double –vee groove X型坡⼝Single bevel groove 单V型坡⼝Double bevel groove K型坡⼝Single –J groove J型坡⼝Double –J groove 双⾯J型坡⼝Defect of welds 焊接缺陷Porosity ⽓孔Density porosity 密集⽓孔Density slag 密集夹渣Slag 夹渣Inclusion 夹杂Crack 裂纹Chill crack 冷裂纹Hot crack 热裂纹Intercrystalline crack 晶间裂纹Undercut 咬边Lack of penetration 未焊透Lack of fusion 未熔合Excessive penetration 焊瘤Root concavity 凹陷Visual inspection (VT) 外观检查Macro(macrography)examination宏观检查Metallographic examination ⾦相检查Penetration test (PT) （着⾊）渗透检查Ultrasonic test (UT) 超声波检查Radiographic test (RT) 射线检查Magnaflux test (MT) 磁粉检查Spectral analysis 光谱分析Etching 浸蚀Weld metal 焊缝⾦属Welding seam 焊缝Weld bead 焊道Fillet weld ⾓焊缝Fusion line 熔合线Base metal 母材Heat affected zone 熱影响区Flux (熔剂)焊剂Heat input 线能量Globular transfer 熔滴过渡Reinforcement of weld 焊缝余⾼Thickness 厚度Backing 衬垫Back gouging 背⾯清根Travel speed 焊速Multi layer 多层Single layer 单层Direct current electrode negative 正接法Direct current electrode positive 反接法Procedure qualification records (PQR)⼯艺评定记录Procedure qualification ⼯艺评定Welding variables procedure specification (WPS)焊接⼯艺规程Electrode 电焊条wire 焊丝weldment (焊接结构)焊件Welding torch 焊枪Splash 飞溅Convex root 根部凸出Common low-alloy steel 普低钢Acetylene ⼄炔Filler metal 填充⾦属Offset（偏移）错⼝Lag ⽑刺Bake 烘烤Deformed 变形Mend 挖补Oxidize 氧化Overburnt 过烧。
焊接专业术语中英文对照整理
焊接专业术语中英文对照整理机械——焊接专业术语中英文对照（郭运）整理1Single 单面的2V—groove V型坡口3Joint 焊接接头4Edges overlap 接头形式5Butt 对接6T T型焊接7Fillet 角焊缝8Edge 端接9Corner 角接10Radius 半径11Joint root 焊接根部12Bevel angle 削边角度13Groove angle 坡口角度14Root face 根部钝边15Groove face 坡口面16Plug weld 塞焊17Spot weld 点焊18Seam weld 缝焊19Slot weld 槽焊20Double—flare—bevel—groove K型坡口焊缝21Single—flare—V 单面V型22Edge flange 翻边端接23Corner flange 卷边端接24Flange weld 卷边焊缝25Flare weld 扩口焊缝26Fillet weld 角焊缝27Slot weld 槽焊缝28Spot weld 点焊缝29Surfacing weld 堆焊焊缝30Melt—through weld 熔透焊缝31Backing weld 打底焊缝32Back weld 背面焊缝33Root weld 根部焊缝34Crown weld 隆起部分35Weld reinforcement 焊缝加强36Weld face 焊缝表面37Cap pass 盖面焊道38Weld edge 焊缝边缘39Leg 焊脚40Toe 焊趾41Buildup 堆焊42Weld reinforcement 焊缝加强高43Effective throat 有效焊喉44Concave weld 凹形焊缝45Convex weld 凸形焊缝46Unequal leg fillet 不等脚角焊47Oversize weld 大尺寸焊缝48Depth of fusion 熔合深度49Depth of penetration 熔透深度50Root penetration 根部熔深51Joint penetration 接头熔深52Weld interface 焊缝分界面53Diameter of weld at point of contact 焊缝在接触点上的直径54Thickness 厚度55Tail 尾部56Arrow 箭头57Reference line 参考线58Arrow side 箭头一边59Weld symbol 焊缝符号60Near side 近侧61Arrow side 箭头侧62Far side 远侧63Other side 另一侧64Put the weld on either—side 在任意一侧施焊65There is noside significance 没有方向区别66Edge flange 双卷边67Corner flange 单卷边68Weld size 焊缝尺寸69Effective throat 有效厚度70Root opening 根部间隙71Full penetration double bevel—groove weld K形坡口全焊透焊缝72Full penetration double V—groove weld 双V形坡口全焊透焊缝73Partial penetration double bevel—groove weld K形坡口部分焊透焊缝74Partial penetration double V—groove weld 双V形坡口部分焊透焊缝75Bevel groove 削边坡口76Flare groove 喇叭形坡口77Flange groove 卷边坡口78V—groove V形坡口79Staggered intermittent fillet weld 交错间断角焊缝80Chain intermittent fillet weld 链状间断角焊缝81Segmented fillet weld 分段角焊缝82Pitch distance 间距83Depth of filling 填充深度84Slot weld width 槽焊缝宽度85Plug weld diameter 塞焊缝的直径86Angle of countersink 深孔角度87A dimension to the right of the symbol 在符号右边的尺寸88A dimension of the required suggest diameter 所要求的直径尺寸89A value for the required shear strength per spot 每点所要求的剪切强度值90Spot weld size 点焊缝尺寸91Spot weld length 点焊缝的长度92Number of spot required 所要求的点的数量93Pitch distance between adjacent spots 两个相邻点的间距94Reference line 参考线95Melt—through of weld from other side 焊缝在另一侧熔透96Single bevel—groove weld with backing weld 加垫板的单边坡口焊缝97Single bevel—groove weld with back weld 背面焊的单边坡口焊缝98Single bevel—groove weld with backing weld 带垫板的V 形坡口焊缝99Single bevel—groove weld with back weld背面焊的V形坡口焊缝100Square groove 直边坡口101Skewed groove 斜坡口102Sloped groove 倾斜坡口103Scarf 斜嵌接104Gas metal arc spot weld 气体保护点焊105Resistance spot weld 电阻点焊106Gas metal arc seam weld 气体保护滚焊缝107Resistance seam weld 电阻滚焊缝108Gas metal arc slot weld 气体保护槽焊缝109The type of electrode to use 所要求焊条形式110The weld quality standard 焊缝质量标准111The weld procedure to use 所用的焊接程序112Codes 规范113Drawing 图纸114Specifications 技术要求115Contracts 合同116General 一般注解117Local 局部注解118The point for lifting an object 吊装一物体的点119Filler metals 填充金属120Pressure vessel fabrication 压力容器制造121Be as simple as possible 尽可能简单122Welder 焊工123Code body 规范本身124Shielded metal arc 手工电弧焊125Submerged arc 埋弧焊126Face bend 面弯127Root bend 背弯128Side bend 侧弯129Nick break 缺口破坏130Tensile 拉伸131Monitoring production welding 监视生产中的焊接132Strength 强度133Toughness 韧性134Hardness 硬度135Ductility 延展性136Compressive 压缩137Impact 冲击138Fatigue 疲劳139Undercut 咬边140Overlap 焊瘤141Cracking 裂纹142Porosity 气孔143Ultimate tensile strength 极限拉伸强度144Percent elongation 延伸率145Percent reduction of area 断面收缩率146Impact strength 冲击强度147Yield strength 屈服强度148Brinell 布氏149Vickers 韦氏150Rockwell 洛氏151Knoop 努氏152Fatigue test 疲劳试验153T ensile test 拉伸试验154Micro--hardness test 显微硬度试验155Charpy impact test 夏比冲击试验156Soundness test 致密性测试157Fillet break 角焊缝断裂158Metallographic 金相159Transverse fillet weld shear test 横向角焊缝剪切试验160Quality of the fractured weld 焊缝端口的质量161Ductility of the weld metal 焊缝金属的延展性162Impact strength of the weld 焊缝的冲击强度163Tensile strength of the base metal 母材的拉伸强度164Weld—ability 可焊性165Scratches caused by improper handling 由不适当的处理导致的划痕166Incomplete fusion 未熔合167Distortion 变形168Slag inclusions 夹渣169Vibratory stress relief 振动消除应力170External restraint 外部拘束171Thermal stress relief 热消除应力172Peening 锤击173Annealing 退火174Quenching 淬火175Tempering 回火176Normalizing 正火177Decrease current 降低电流178Decrease voltage 降低电压179Increase travel speed 加快焊接速度180Change from weave to stringer bead technique 从横向摆动焊道改成直线焊道技术181Result in a wider heat—affected zone hardness导致热影响区更宽182Produce a lower heat—affected zone hardness 降低热影响区硬度183Slow down the cooling rate 降低冷却速度184Reduce the tendency to produce martensite in the heat—affected zone 减少在热影响区形成马氏体的倾向185Stress relief 消除应力186Crater crack 弧坑裂纹187SMAW 手动电弧焊188PAW 等离子焊189FCAW 药芯焊190SAW 埋弧焊191Underfill 未焊满192Excess convexity 太凸193Excess weld reinforcement 焊缝余高太高194Overfill 过充195Scratch start 擦伤196Arc strike 引弧烧伤197Tungsten inclusion 夹钨198Lamination 分层199Lamellar tear 片状撕裂200Seam 划伤201Pipe shrinkage 缩孔202Longitudinal crack 纵向裂纹203Transverse crack 横向裂纹204Underbead crack 焊道中裂纹205T oe crack 焊趾裂纹206Root crack 根部裂纹207Base metal crack 母材裂纹208Before welding 焊接前209During welding 焊接时210After welding 焊接后211Waiting time 等待时间212Penetrating time 渗透时间213Soak time 吸入时间214Dwell time 驻留时间215AC 交流电216DC 直流电217DCEP 直流反接218。
2021年-焊接专业术语中英文对照整理
机械——焊接专业术语中英文对照（郭运）整理1Single单面的2V—groove V 型坡口3Joint焊接接头4Edges overlap接头形式5Butt对接6T T 型焊接7Fillet角焊缝8Edge端接9Corner角接10Radius半径11Joint root焊接根部12Bevel angle削边角度13Groove angle坡口角度14Root face根部钝边15Groove face坡口面16Plug weld塞焊17Spot weld点焊18Seam weld缝焊19Slot weld槽焊20Double—flare—bevel—groove K 型坡口焊缝21Single—flare—V单面 V型22Edge flange翻边端接23Corner flange卷边端接24Flange weld卷边焊缝25Flare weld扩口焊缝26Fillet weld角焊缝27Slot weld槽焊缝28Spot weld点焊缝29Surfacing weld堆焊焊缝30Melt —through weld熔透焊缝31Backing weld打底焊缝32Back weld背面焊缝33Root weld根部焊缝34Crown weld隆起部分35Weld reinforcement焊缝加强36Weld face焊缝表面37Cap pass盖面焊道38Weld edge焊缝边缘39Leg焊脚40Toe焊趾41Buildup堆焊42Weld reinforcement焊缝加强高43Effective throat有效焊喉44Concave weld凹形焊缝45Convex weld凸形焊缝46Unequal leg fillet不等脚角焊47Oversize weld大尺寸焊缝48Depth of fusion熔合深度49Depth of penetration熔透深度50Root penetration根部熔深51Joint penetration接头熔深52Weld interface焊缝分界面53Diameter of weld at point of contact焊缝在接触点上的直径54Thickness厚度55Tail尾部56Arrow箭头57Reference line参考线58Arrow side箭头一边59Weld symbol焊缝符号60Near side近侧61Arrow side箭头侧62Far side远侧63Other side另一侧64Put the weld on either—side在任意一侧施焊65There is no side significance没有方向区别66Edge flange双卷边67Corner flange单卷边68Weld size焊缝尺寸69Effective throat有效厚度70Root opening根部间隙71Full penetration double bevel —groove weld K 形坡口全焊透焊缝72Full penetration double V—groove weld双 V 形坡口全焊透焊缝73Partial penetration double bevel—groove weld K形坡口部分焊透焊缝74Partial penetration double V—groove weld双 V形坡口部分焊透焊缝75Bevel groove削边坡口76Flare groove喇叭形坡口77Flange groove卷边坡口78V—groove V 形坡口79Staggered intermittent fillet weld交错间断角焊缝80Chain intermittent fillet weld链状间断角81Segmented fillet weld分段角焊缝82Pitch distance间距83Depth of filling填充深度84Slot weld width槽焊缝宽度85Plug weld diameter塞焊缝的直径86Angle of countersink深孔角度87A dimension to the right of the symbol在符号右边的尺寸88 A dimension of the required suggest diameter 所要求的直径尺寸89 A value for the required shear strength per spot 每点所要求的剪切强度值90Spot weld size点焊缝尺寸91Spot weld length点焊缝的长度92Number of spot required所要求的点的数量93Pitch distance between adjacent spots两个相邻点的间距94Reference line参考线95Melt —through of weld from other side焊缝在另一96Single bevel—groove weld with backing weld 加垫板的单边坡口焊缝97 Single bevel—groove weld with back weld背面焊的单边坡口焊缝98Single bevel—groove weld with backing weld 带垫板的 V 形坡口焊缝99Single bevel—groove weld with back weld 背面焊的 V 形坡口焊缝100Square groove直边坡口101Skewed groove斜坡口102Sloped groove倾斜坡口103Scarf斜嵌接104Gas metal arc spot weld气体保护点焊105Resistance spot weld电阻点焊106Gas metal arc seam weld气体保护滚焊缝107Resistance seam weld电阻滚焊缝108Gas metal arc slot weld气体保护槽焊缝109The type of electrode to use所要求焊条形式110The weld quality standard焊缝质量标准111The weld procedure to use所用的焊接程序112Codes规范113Drawing图纸114Specifications技术要求115Contracts合同116General一般注解117Local局部注解118The point for lifting an object吊装一物体的点119Filler metals填充金属120Pressure vessel fabrication压力容器制造121Be as simple as possible尽可能简单122Welder焊工123Code body规范本身124Shielded metal arc手工电弧焊125Submerged arc埋弧焊126Face bend面弯127Root bend背弯128Side bend侧弯129Nick break缺口破坏130Tensile拉伸131Monitoring production welding监视生产中的焊接132Strength强度133Toughness韧性134Hardness硬度135Ductility延展性136Compressive压缩137Impact冲击138Fatigue疲劳139Undercut咬边140Overlap焊瘤141Cracking裂纹142Porosity气孔143Ultimate tensile strength极限拉伸强度144Percent elongation延伸率145Percent reduction of area断面收缩率146Impact strength冲击强度147Yield strength屈服强度148Brinell布氏149Vickers韦氏150Rockwell洛氏151Knoop努氏152Fatigue test疲劳试验153Tensile test拉伸试验154Micro--hardness test显微硬度试验155Charpy impact test夏比冲击试验156Soundness test致密性测试157Fillet break角焊缝断裂158Metallographic金相159Transverse fillet weld shear test横向角焊缝剪切试验160Quality of the fractured weld焊缝端口的质量161Ductility of the weld metal焊缝金属的延展性162Impact strength of the weld焊缝的冲击强度163Tensile strength of the base metal母材的拉伸强度164Weld—ability可焊性165Scratchescaused by improper handling 由不适当的处理导致的划痕166Incomplete fusion未熔合167Distortion变形168Slag inclusions夹渣169Vibratory stress relief振动消除应力170External restraint外部拘束171Thermal stress relief热消除应力172Peening锤击173Annealing退火174Quenching淬火175Tempering回火176Normalizing正火177Decrease current降低电流178Decrease voltage降低电压179Increase travel speed加快焊接速度180Change from weave to stringer bead technique 从横向摆动焊道改成直线焊道技术181Result in a wider heat —affected zone hardness导致热影响区更宽182Produce a lower heat —affected zone hardness 降低热影响区硬度183Slow down the cooling rate降低冷却速度184Reduce the tendency to produce martensite in the heat—affected zone减少在热影响区形成马氏体的倾向185Stress relief消除应力186Crater crack弧坑裂纹187SMAW手动电弧焊188PAW等离子焊189FCAW药芯焊190SAW埋弧焊191Underfill未焊满192Excess convexity太凸193Excess weld reinforcement焊缝余高太高194Overfill过充195Scratch start擦伤196Arc strike引弧烧伤197Tungsten inclusion夹钨198Lamination分层199Lamellar tear片状撕裂200Seam划伤201Pipe shrinkage缩孔202Longitudinal crack纵向裂纹203Transverse crack横向裂纹204Underbead crack焊道中裂纹205Toe crack焊趾裂纹206Root crack根部裂纹207Base metal crack母材裂纹208Before welding焊接前209During welding焊接时210After welding焊接后211Waiting time等待时间212Penetrating time渗透时间213Soak time吸入时间214Dwell time驻留时间215AC交流电216DC直流电217DCEP直流反接218。
焊接名词中英文对照
continuous weld process连续式炉焊管法
contour weld特形焊接
convex fillet weld凸角焊缝; 凸形角焊缝
convex weld凸焊缝; 凸形焊缝
copper weld wire包铜钢丝
corner flange weld单卷边角焊缝
表面裂纹surface crack
咬边undercut
焊瘤overlap
凹坑pit
烧穿burn through
塌陷excessive penetration
未焊透incomplete penetration/ lack of penetration
未熔合lack of fusion/ incomplete fusion
X射线工业电视探伤X-ray industrial television inspection
磁粉探伤magnetic particle inspection
电磁探伤electromagnetic inspection/ eddy current test
探伤灵敏度flaw detection sensitivity
dissimilar weld metal不同的焊接金属; 不同金属的焊接
distance between the toes of a weld焊缝宽度
double groove weld双面坡口焊缝
double-bevel groove weld双斜边坡口焊缝; 双斜坡口焊
double-flanged butt weld双弯边对接焊缝
比较全面的焊接英语词汇，可以直接看不用下载呀
焊接专业术语中英对照
焊接专业术语中英对照焊接欠缺与检验焊接欠缺welding imperfection焊接缺陷weld defect气孔blowhole/ gas pore针尖状气孔pinhole密集气孔porosity条虫状气孔wormhole裂纹crack表面裂纹surface crack咬边undercut焊瘤overlap凹坑pit烧穿burn through塌陷excessive penetration未焊透incomplete penetration/ lack of penetration未熔合lack of fusion/ incomplete fusion 未焊满incompletely filled weld根部凹陷root concavity电弧擦伤arc scratch夹渣slag inclusion夹杂物inclusion夹钨tungsten inclusion白点fish eye/ flake错边misalignment/ dislocation焊接检验试件test piece试样test specimen无损检验nondestructive test破坏检验destructive test外观检查visual examination超声波探伤ultrasonic inspection直射法超声波探伤straight beam method斜射法超声波探伤angle beam method液浸法超声波探伤immersion method射线探伤radiographic inspection/ radiographyX射线探伤X-ray radiographic inspection γ射线探伤gamma-ray inspectionX射线工业电视探伤X-ray industrial television inspection磁粉探伤magnetic particle inspection电磁探伤electromagnetic inspection/ eddy current test 探伤灵敏度flaw detection sensitivity渗透探伤penetration inspection荧光探伤flurescent penetrant inspection 着色探伤dye penetrant inspection密封性检验leak test气密性检验air tight test枕形气密检验pillow test耐压检验pressure test水压检验hydraulic test气压检验pneumatic test液晶检验liquid crystal test声发射检测acoustic emission testing面弯试验face bend testing背弯试验root bend test侧弯试验side bend test横弯试验horizontal bend test纵弯试验axial bend test压扁试验squeezing testactual weld-throat thick-ness焊缝厚度all-around weld整周焊缝all-around weld (整周焊缝)环焊缝angle butt weld斜对接焊angle weld角焊appearance of weld焊缝成形arc-seam weld电弧缝焊arc-spot weld电弧点焊arc-weld电弧焊aspect ratio of weld焊缝成形系数at weld edge在焊缝边上attachment weld连接焊缝automatic spot weld自动点焊法automatic weld自动焊接axis of a weld焊缝行南? 焊接轴线axis of weld焊缝轴线; 焊接轴线back of weld焊缝背面backing groove of weld焊缝反面坡口backing weld底焊; 底焊焊缝bare metal arc weld裸焊条电弧焊bead weld珠焊; 堆焊bead-on-plate weld堆焊焊缝beading weld凸焊beam-to-beam weld梁间焊接; 梁式引线焊接block sequence weld分段多层焊bond weld钢轨接头焊接bridge seam weld桥缝焊接; 桥线焊brize weld硬焊页脚.butt weld对接焊缝butt weld ends对头焊接端butt-weld碰焊; 平式焊接; 对头焊接butt-weld in the downhand position对接平焊butt-weld joint对头焊接butt-weld pipe mill对焊管轧机button spot weld按电钮点焊cap weld最后焊层; 盖面焊缝carbon content of weld materials焊接材料的碳含量cast-weld construction铸焊结构caulk weld填缝焊caulking weld密实焊缝chain intermittent fillet weld链式分段角焊; 并列间断角焊缝chain intermittent weld并列焊接circular weld环形焊缝circumferential weld环缝; 环焊缝cleft weld裂口焊closed weld底边无缝焊; 无间隙焊缝closed-chamber fusion weld闭室熔焊cluster weld丛聚焊缝coil weld卷板对接焊; 卷板对接焊; 板卷焊cold weld冷压接commutator-controlled weld换向控制焊接complete penetration butt weld贯穿对焊composite weld紧密焊缝; 强度密封焊缝concave filled weld凹形角焊缝concave filler weld凹角焊concave fillet weld凹面填角焊concave weld凹焊缝; 凹面焊; 凹形焊缝; 轻型焊connective weld联系焊缝continuous butt-weld mill连续式炉焊管机组continuous fillet weld连续(填)角焊缝; 连续角焊缝; 连续贴角焊continuous weld连续焊缝continuous weld process连续式炉焊管法contour weld特形焊接convex fillet weld凸角焊缝; 凸形角焊缝convex weld凸焊缝; 凸形焊缝copper weld wire包铜钢丝corner flange weld单卷边角焊缝corner weld角焊corner-flange weld卷边角焊缝; 卷边角焊缝crack of weld焊部裂纹cross weld十字交叉焊缝; 横向焊缝cross-wire weld十字焊crotch weld楔接锻接; 楔接焊接cup weld带盖板焊缝depth of weld焊接深度dissimilar weld metal不同的焊接金属; 不同金属的焊接distance between the toes of a weld焊缝宽度double groove weld双面坡口焊缝double-bevel groove weld双斜边坡口焊缝; 双斜坡口焊double-flanged butt weld双弯边对接焊缝double-V groove weld双斜边坡口焊缝; 双斜坡口焊downhand weld平焊缝duplex spot weld双点点焊接头edge joint weld边缘焊edge weld端接焊; 端接焊缝; 端面焊缝; 对边焊electric resistance weld mill电阻焊管机electric weld-pipe mill电焊管机焊接专业英语词汇（通用部分）acetylene 乙炔 ampere 电流安培angle welding 角焊 arc 电弧argon arc welding 氩弧焊接 bare electrode 光熔接条butt welding 对接焊接 camber 电弧弯曲cascade 阶叠熔接法 clad weld 被覆熔接crator 焊疤 excess metal 多余金属filler rod 焊条 fillet weld 填角焊接gas shield 气体遮蔽 groove welding 起槽熔接hand face shield 手握面罩 hard facing 硬表面堆焊jig welding 工模焊接 laser beam welding 雷射光焊接metal electrode insert gas welding MIG熔接nugget 点焊熔核overlaying 堆焊 peening of welding 珠击熔接法plug welding 塞孔熔接 positioned welding 正向熔接pressure welding 压焊 propane gas cutting 丙烷气切割页脚.pure nickel electrode 纯镍熔接条reinforcement of weld 加强焊接resist 抗蚀护膜 root running 背面熔接seam 焊缝 seaming 接合seam welding 流缝熔接 series seam welding 串联缝熔接skip welding process 跳焊法 spark 火花spot welding 点焊接 stitch welding 针角焊接stud arc welding 电弧焊接 under laying 下部焊层void 焊接空隙 weld flow mark 焊接流痕weld flush 焊缝凸起 weld line 焊接纹weld mark 焊接痕 weld penetration 熔接透入weld zone 焊接区 welding 焊接welding bead 焊接泡 welding direction 焊接方向welding distortion 焊接变形 welding flux 焊剂welding ground 电熔接地 welding interval 焊接周期welding stress 熔接应变 welding torch 熔接气炬welding electrode production line 电焊条生产线welding electrode 焊条welding fixture 焊接夹具welding generator 电焊机welding goggles 焊工护目镜welding gun 焊枪welding helmet 电焊帽welding inspection ruler 焊接检验尺welding machine 焊接机welding mill 焊管机welding motor generator 电动焊接发电机welding nozzle 焊嘴welding paste 焊接药膏welding pipe 焊接管welding powder 焊粉welding rectifier 焊接整流器welding robot 焊接机器人welding rod extrusion press 焊条挤压机welding rod with acidic coating 酸性焊条welding rod with alkaline coating 碱性焊条welding rod 焊条welding simulator 焊接模拟器welding stainless electrode 不锈电焊条welding steel tube 焊接钢管welding tin billet 焊锡棒料welding tongs 焊接夹钳welding torch 焊炬welding transformer 电焊变压器welding unit 焊机welding wire machine 焊线机welding wire 焊丝welding-cutting hose 熔焊及切割胶管welding-cutting tool 焊割具welding-rod core 焊条芯welding-seam cleaner 焊缝清理机weldless pipe 无缝管weldless steel tube 无缝钢管well borer 凿井机well counter 井式计数器well deck vessel 井形甲板船well drill 钻井机well platform 钻井平台well rig 钻井机well testing truck 试井车well thermometer 井温计well tube filter 井管滤管well type tempering electric furnace 井式回火电炉well winch 矿井绞车well-logging probe 测井探头well-type counter 井型计数器Wella Balsam Conditioner 威娜宝护发素Wella Balsam shampoo 威娜宝香波Wellene 韦纶聚酯短纤维wellhead acid preventer 井口防酸器wellington 惠灵顿防雨呢Wellingtons 长筒皮靴Welltite 韦纶泰特聚丙烯和聚乙烯单丝Welsbach's alloy 韦尔斯巴赫发火合金Welsh flannel 威尔士法兰绒Welsh wool 威尔士粗羊毛welsh-onion stalk 葱白welsh-onion 葱welt cementing machine 贴边粘合机welt coloring machine 贴边染色机welt cutting machine 切沿条机welt fitting machine 贴边机welt footwear 加贴边的鞋页脚.welter screen 翻滚筛welter 镶边机Wepsin 三唑磷胺Werlisa 威里沙牌照相机Werner 维尔纳牌手表weskit 紧身背心Wessel silver 韦塞尔铜镍锌合金West cigarette 威狮牌香烟West ginseng 西洋参West Lake Dragon Well tea 西湖龙井茶West Lake silk umbrella 西湖绸伞West Lake silk 西湖丝绸West Lake water shield 西湖莼菜Westeeco 韦斯蒂科镍铬铁耐热合金Western king prawn 宽沟对虾Western saddle pants 西式马裤Western sand cherry 沙樱桃Western shirt 西式衬衫western style bed sheet 西式床单Western style hat 西式呢帽Western style pajamas 西式睡衣裤Western style pants 西裤Western style shirt 西式衬衫Western style shirt-waist blouse 西式衬衫上衣Western style suit 西服western tie 西式领带Western wool 美国西部羊毛Western-made shirt in plaid gingham 长方格贞咸布西式衬衫Westinghouse alloy 西屋镍铜热磁补偿合金wet spinning frame 湿纺细纱机wet air compressor 湿空气压缩机wet air pump 湿空气泵wet and dry bulb hygrometer 干湿球湿度计wet and dry bulb recording hygrometer 干湿球自记湿度计wet and dry bulb thermometer 干湿球温度计wet ball mill 湿式球磨机wet blue goat leather 山羊蓝湿革wet blue goat skin 蓝湿山羊皮wet board machine 湿式纸板机wet brush 湿刷wet chrome goat skin 铬湿山羊皮wet cleaner 湿法清洗器wet cloth 湿光布wet clutch 湿式离合器wet collector 湿式除尘器wet condenser 湿式冷凝器wet crude 含水原油wet crushing mill 湿粉碎机wet cylinder liner 湿式气缸套wet drill 湿式风钻wet dust collector 湿式收尘器wet dust separator 湿式除尘器wet electro-magnet 湿式电磁铁wet electrolytic capacitor 电解液电容器wet feeder 湿式给料机wet fiber filter 湿式纤维过滤器wet filter 湿式过滤器wet fourdrinier board machine 长网湿抄机wet frame 湿纺机wet furfural condenser 含水糖醛冷凝器wet gas meter 湿式气量计wet gas scrubber 湿法气体洗涤质量合格证书certification of fitness原材料rawmaterial底板 bottom plate垫层 cushion侧壁 sidewall中心线center line条形基础 strip footing附件 accessories型钢 profile steel钢板 steel plate熔渣 slag飞溅 welding spatter定位焊 tacking引弧 generating of arc熄弧 quenching of arc焊道 welding bead坡口 beveled edges外观检查 visual inspection重皮 doubleskin水平方向弧度 radian in horizontal direction 成型 molding直线度 straightness accuracy焊缝角变形 welding line angular distortion 水平度 levelness铅垂度 verticality翘曲变形 buckling deformation角尺 angle square页脚.对接焊缝 butt weld母材 parent metal法兰密封面 flange sealing surface夹层interlayer表面锈蚀浓度 surface corrosion concentration挠曲变 bending deformation超声波探伤 ultrasonic testing/ ultrasonic examination压力容器 pressure vessel预制下料prefabrication baiting排版直径 set-type diameter焊缝 welding line中幅板 ? center plate测量方法 measuring method基准点 datum mark跳焊 skip welding允许偏差 allowable variation补强板 stiffening plate开孔 tapping对接接头 banjo fixing butt jointing角钢 angle iron安装基准圆 installation fundamental circle 吊装立柱 hoisting upright column焊接钢管 welded steel pipe向心斜拉筋 centripetal canting pull rope 带板 band plate槽钢胀圈 channel steel expansion ring环口 collar extension局部变形 local distortion环缝 circumferential weld顶板 top plate拱顶 vault顶板加强肋 stiffening rib对接 butt joint胎具 clamping fixture卷板机 plate bending rolls中心支架 center bearing bracket椭圆度 ovality等分线 bisectrix搭接宽度lap width点焊spot welding搭接焊 overlap welding对称：symmetrically螺旋爬梯cockle stairs放料阀baiting valve 液位计 content gauge充水试验 filling water test错边量 unfitness of butt joint底圈 foundation ring真空度检漏 vacuum degree leak test丁字焊缝 tee welding渗透探伤 oil whiting test充水试验 filling water test侧角焊缝接头 interior angle welding line jointfoundation settlement 基础沉降测量基准点 datum mark?稳定性试验 stability test排气阀 outlet valve角钢 angle steel构件 component part机械损伤 mechanical damage缩孔 shrinkage cavityenfoldment 折迭碳钢管 carbon steel tube公称直径 nominal diameter预埋件 embedded part轴测图 axonometric drawing布置图arrangement diagram氧乙炔气割 oxyacetylene gas cutting低合金钢管low alloy steel热影响区 heat affected area修磨polish砂轮片grinding wheel等离子plasma panel重皮 coldlap凹凸unevenness缩口necking down端面 head face倾斜偏差 dip deviation外径 external diameter砂轮grinding wheel管件 pipe casting单线图single line drawing平齐parallel and level两端 two terminals满扣 buckle螺栓紧固 bolton周边 periphery附加应力 additional stress页脚.同轴度 axiality平行度 parallelism随机 stochastic允许偏差 allowable variation重直度verticality水平度 levelness隔离盲板 blind plate氩弧焊argon arc welding压盖螺栓 gland bolt间距spacing有效期 period of validity担任 take charge of ;undertake焊条 welding rod碳钢焊条carbon steel焊丝 welding wire熔化焊 melting钢丝 steel wire气体保护焊 gas shielded arc welding 烘干drying清洗ablution制度system焊接工艺welding procedure相应corresponding手工电弧焊manual electric arc welding 手工钨极 manual tungsten electrode打底render电源power source交流alternating current焊件 weldment管壁厚度 pipe thickness对接焊缝 butt weld工件壁厚 workpiece飞溅物 splash沾污 smirch油污 oil stain细锉 smooth file铣刀 milling cutter氧化膜 oxide film脱脂处理 ungrease treatment]棉质纤维 cotton fibre丙酮acetone硫 sulfur焊剂 welding flux钢板 steel plate纵向焊缝 l0ngitudinal weld l0ngitudinal seam筒节 shell ring 封头 end socket卷管 reelpipe强度试验strength test起弧arc starting穿堂风draught熔合fusion反面reverse side整体integral封堵block up焊口 weld bond医用胶布medical proof fabric高频 high frequency焊炬welding torch送气air supply焊接专业英语词汇（熔化焊）熔接fusion welding压接pressure welding焊接过程welding process焊接技术welding technique焊接工艺welding technology/procedure焊接操作welding operation焊接顺序welding sequence焊接方向direction of welding焊接位置welding position熔敷顺序build-up sequencedeposition sequence焊缝倾角weld slope/inclination of weld axis 焊缝转角weld rotation/angle of rotation平焊位置flat position of welding横焊位置horizontal position of welding立焊位置vertical position of welding仰焊位置overhead position of welding平焊downhand welding/flat position welding 横焊horizontal position welding立焊vertical position welding仰焊overhead position welding全位置焊all position welding：熔焊时，焊件接逢所处空间位置包括平焊、横焊、仰焊等位置所进行的焊接。
焊接术语中英对照
电阻焊 resistance welding (RW)点焊 spot welding；resistance spot welding凸焊 projection welding缝焊 seam welding滚点焊 roll-spot welding连续点焊 stitch welding多点焊 multiple spot welding手压点焊 push welding；poke welding单面点焊 indirect spot welding双面点焊 direct spot welding脉冲点焊 pulsation spot welding；multiple-impulse welding串联点焊 series spot welding多点凸焊 multiple projection welding频道进缝焊 step-by-step seam welding压平缝焊 mash seam welding串联缝焊 series seam welding对接缝焊 butt seam welding；foil-butt seam电阻对焊 upset butt welding闪光对焊 flash butt welding (FBW)储能焊 stored energy welding电容储能点焊 condenser discharge spot welding高频电阻焊 high frequency resistance welding冲击电阻焊 percussion welding胶接点焊 spot weld-bonding；weld-bonding 塑料喷涂 plastic spraying陶瓷喷涂 ceramic spraying喷熔 spray-fusing表面粗糙化处理 surface roughening电火花拉毛 electrospark roughening抛锚效应 anchoring喷涂层 spray-fused coating喷熔层 spray-fused coating结合层 bond coating；under coating工作层 work coating结合强度 adhesive strength涂层强度 strength of coating封孔处理 sealing封孔剂 sealant喷涂率 spray rate沉积效率 deposition efficiency孔隙率 porosity喷涂材料 spraying material自熔剂合金粉末 self-fluxing alloy powder 喷炬（枪） spray torch；热切割 thermal cutting (TC)气割 gas cutting；oxygen cutting氧溶剂切割 powder cutting氧-石英砂切割 quartz powder cutting闪光 flashing；flash过梁 bridge；lintel顶锻 upsetting；upset夹紧力 clamping force顶锻力 upsetting force；upset force电极压力 electrode force；electrode pressure电极滑移 electrode skid焊接循环 welding cycle预压时间 squeeze time锻压时间 forge-delay time；forge time焊接通电时间（电阻焊） welding time (resistance welding)预热时间 preheat time加热时间 heat time冷却时间 cool time间歇时间 quench time；chill time回火时间 temper time维持时间 hold time休止时间 off time闪光时间 flash time；flashing time顶锻时间 upset time；upsetting time有电顶锻时间 upset current time无电顶锻时间 upset current-off time闪光速度 flashing speed闪光电流 flashing current；flash current顶锻电流 upset current预热电流 preheat current 电弧切割 arc cutting氧气电弧切割 oxy-arc cutting空气电弧切割 air arc cutting等离子弧切割 plasma arc cutting (PAC)空气等离子弧切割 air plasma arc cutting氧等离子切割 oxygen plasma arc cutting水再压缩空气等离子弧切割 air plasma water injection arc cutting双层气流等离子弧切割 dual gas plasma arc cutting；shielded gas plasma arc cutting激光切割 laser cutting(LC)；laser beam cutting电子束切割 electron beam cutting喷气激光切割 gas jet laser cutting碳弧切割 carbon arc cutting水下切割 underwater cutting喷水式水下电弧切割 waterjet method underwater arc cutting氧矛切割 oxygen lancing；oxygen lance cutting溶剂氧切割 powder lancing手工气割 manual oxygen cutting自动气割 automatic oxygen cutting仿形切割 shape cutting数控切割 NC (numerical-control) cutting快速切割 high-speed cutting垂直切割 square cut叠板切割 stack cutting坡口切割 beveling；bevel cutting回火电流 temper current调伸长度 initial overhange；extension 总留量 total allowance闪光留量 flash allowance顶锻留量 upset allowance顶锻速度 upset speed电极接触面 electrode contact surface 贴合面 faying surface焊点 welding spot熔核 nugget熔核直径 diameter of nugget塑性金属环区 corona bond焊透率 penetration rate压痕 indentation压痕深度 depth of indentation压深率 indentation ratio翘离 sheet separation缩孔 shrinkage cavity胡须 intrusion电极粘损 electrode pick up喷溅 splash/ expulsion毛刺 fin飞边 upset metal/ fin焊点距 weld spacing/ spot weld spacing 边距 edge distance分流 shunt current 碳弧气割 carbon arc air gouging火焰气刨 flame gouging火焰表面清理 scarfing氧熔剂表面修整 powder washing预热火焰 preheat flame预热氧 preheat oxygen切割氧 cutting oxygen/ cutting stream切割速度 cutting speed切割线 lone of cut/ cut line切割面 face of cut/ cut face切口 kerf切口上缘 cutting shoulder切口宽度 kerf width后拖量 drag切割面平面度 evenness of cutting surface/ planeness of cutting surface割纹深度 depth of cutting veins/ stria depth切割面质量 quality of cut face上缘熔化度 shoulder meltability/ melting degree of shoulder切口角 kerf angle缺口 notch挂渣 adhering slag结瘤 dross割炬 cutting torch/ cutting blowpipe/ oxygen-fuel gas cutting torch割枪 cutting gun割嘴 cutting nozzle/ cutting tip接触电阻 contact resistance电阻焊机 resistance welding machine点焊机 spot welding machine多点焊机 multiple spot welding machine移动式点焊机 portable spot welding machine缝焊机 seam welding machine纵横两用缝焊机 universal seam welder对焊机 butt resistance welding machine凸焊机 projection welding machine三相低频焊机 three phase low frequency welder 二次整流电阻焊机 direct current resistance welder secondary rectification电容储能电阻焊机 condenser discharge resistance welder电容储能点焊机 condenser type spot welder/ capacitor spot welding machine工频电阻焊机 mains frequency resistance welding machine低频电阻焊机 frequency converter resistance welding machine高频焊机 high frequency induction welder逆变式电阻焊机 inverter type resistance welding machine全波阻焊电源 full wave resistance welding power source斩波阻焊电源 chopped wave resistance welding power source旋转焊接变压器 rotary welding transformer 快速割嘴 divergent nozzle/ high-speed nozzle表面割炬 gouging blowpipe水下割炬 under-water cutting blowpipe水下割条 electrode for under-water cutting粉剂罐 powder dispenser数控切割机 NC cutting machine门式切割机 flame planer光电跟踪切割机 photo-electric tracing cutting火焰切管机 pipe flame cutting machine磁轮式气割机 gas cutting machine with magnetic wheels焊接结构 welded structure/ welded construction 焊件 weldment焊接部件 weld assembly组装件 built-up member接头设计 joint design焊接应力 welding stress焊接瞬时应力 transient welding stress焊接残余应力 welding residual stress热应力 thermal stress收缩应力 contraction stress局部应力 local stress拘束应力 constraint stress固有应力 inherent stress固有应变区 inherent strain zone残余应力测定 residual stress analysis逐层切割法 Sach’s method点焊钳 spot welding headC形点焊钳 C-type welding head/ C-type gunX形点焊钳 pincer spot welding head/ pliers spot welding head断续器 contactor同步断续器 synchronous contactor异步断续器 non-synchronous contactor程序控制器 sequencer程序时间调节器 sequencer timer电极臂 arm电极握杆 electrode holder电极台板 backup die/ bolster电极水冷管 electrode cooling tube电极头 electrode tip电极帽 electrode cap锥头电极 truncated tip electrode平头电极 flat tip electrode尖头电极 pointed tip electrode球面电极 radius tip electrode偏心电极 offest electrode直电极 straight electrode弯电极 cranked electrode双弯电极 double cranked (swannecked) electrode 滚轮电极 circular electrode/ welding wheel斜棱滚轮电极 bevelled wheel顶锻机构 upsetting mechanism电极总行程 total electrode stroke X射线衍射法 X-ray stress analysis小孔释放法 Mathar method固有应变法 inherent strain method消除应力 stress relieving局部消除应力 local stress relieving应力重分布 stress redistribution退火消除应力 stress relieving by annealing温差拉伸消除应力 low temperature stress relieving 机械拉伸消除应力 mechanical stress relieving应力松弛 stress relaxation焊接变形 welding deformation焊接残余变形 welding residual deformation局部变形 local deformation角变形 angular distortion自由变形 free deformation收缩变形 contraction deformation错边变形 mismatching deformation挠曲变形 deflection deformation波浪变形 wave-like deformation火焰矫正 flame straightening反变形 backward deformation焊接力学 welding mechanics断裂力学 fracture mechanics弹塑性断裂变形 elasto-plastic fracture mechanics 线弹性断裂力学 linear elastic fracture mechanics 延性断裂 ductile fracture脆性断裂 brittle fracture工作行程 operational stroke辅助行程 electrode travel/ electrode stroke臂间距离 horn spacing/ throat opening电极臂伸出长度 arm extension摩擦焊 friction welding (FW)转速 friction speed摩擦压力 friction pressure/ heating pressure摩擦转矩 friction torque摩擦时间 friction time摩擦变形量 burn-off length摩擦变形速度 burn-off rate停车时间 stopping time顶锻变形量 forge length顶锻变形速度 forge rate摩擦表面 friction surface储能摩擦焊 fly-wheel type friction welding径向摩擦焊 radial friction welding扩散焊 diffusion welding (DW)过渡液相扩散焊 transient liquid phase diffusion welding热等静压扩散焊 hot isotatic pressure diffusion welding热轧扩散焊 roll diffusion welding扩散缝焊 seam diffusion welding超塑成形扩散焊 supperplastic forming diffusion bounding隔离剂 buttering material爆炸焊 explosive welding (EW) 应力腐蚀开裂 stress corrosion cracking热应变脆化 hot straining embrittlement临界裂纹尺寸 critical crack size裂纹扩展速率 crack propagation rate裂纹张开位移（COD）crack opening displacement 拘束度 restraint intensity拘束系数 restraint coefficient应变速率 strain rate断裂韧度 fracture toughness应力强度因子 stress intensity factor临界应力强度因子 critical stress intensity factors应力腐蚀临界应力强度因子 critical stress intensity factor of stress corrosion crackingJ积分 J-integration罗伯逊止裂试验 Robertson crack arrest testESSO试验 ESSO test双重拉伸试验 doucle tension test韦尔斯宽板拉伸试验 Well’s wide plate test帕瑞斯公式 Paris formula断裂分析图 fracture analysis diagram焊接车间 welding shop焊接工作间 welding booth焊接工位 welding post/ welding station焊接环境 welding surroundings焊工 welder电焊工 manual arc welder气焊工 gas welder爆炸点焊 explosive spot welding爆炸线焊 explosive line welding多层板爆炸焊 explosive welding of multiplayer plates多层管爆炸焊 explosive welding of multiplayer tubes覆板（覆管） cladding plat (tube)/ flyer plate (tube) 基板（基管） base plate(tube)/ parent plate (tube) 保护层 buffer/ protector基础 base预置角 preset angle间距 initial stand-off/ spacing装药量 explosive load装药密度 charge density/ loading density质量比 mass ratio平行法 parallel plate configuration角度法 preset angle configuration均匀布药 average arranging explosive梯形布药 gradient arranging explosive爆炸焊参数 explosive welding parameters初始参数 initial parameters动态参数 dynamic parameters界面参数 interface parameters爆轰速度 detonation velocity覆板速度 cladding plate velocity碰撞点 impact point碰撞点速度 velocity of the impact point 焊接检验员 weld inspector焊工培训 welders training焊工模拟训练器 trainer of synthetic weld焊工考试 welder qualification test焊工合格证 welder qualification/ welder qualified certification钢板预处理 steel plate pretreatment喷沙 sand blast喷丸 shot blast矫正 straighten开坡口 bevelling (of the edge)/ chanfering装配 assembly/ fitting安装 erect刚性固定 rigid fixing装配焊接顺序 sequence of fitting and welding焊接工艺评定 welding procedure qualification焊接工艺规程 welding procedure specification焊接工艺试验 welding procedure test焊接工艺卡 welding procedure card工序 operational sequence焊接材料消耗定额 welding consumables quota 焊接工时定额 welder-hour quota清渣 slag removal清根 back gouging/ back chipping锤击 peening返修次数 number of rewelding焊接工作台 welding bench弯折角 bending angle碰撞角 collision angle碰撞压力 impact pressure格尼能 Gurney energy垂直碰撞 normal impact倾斜碰撞 oblique impact/ inclined impact对称碰撞 symmetrical impact来流 upper stream出流 down stream再入射流 re-entrant jet自清理 oneself cleaning结合区 bond zone平面结合 plane bond波状结合 wave-like bond界面波长 length of the interfacial wave界面波幅 amplitude of the interfacial wave熔化层 molten layer熔化袋 molten pocket雷管区 detonator zone边界效应 edge effect焊接性窗口 weldability windows焊着率 ratio of welding area起爆方法 method of initiation内爆法 internal explosion process外爆法 external explosion process半圆柱试验法 semi-cylinder experiment method 超声波焊 ultrasonic welding (UW) 装焊平台 welding platen电磁平台 electromagnetic platen焊接翻转机 welding tilter焊接回转台 floor turnable positioner焊接变位机 positioner焊接滚轮架 turning rolls焊接操作机 manpulator焊工升降台 welder’s lifting platform焊接夹具 welding jig/ fixture磁力夹紧器 magnetic jig螺旋推撑器 screw operated tensioning unit焊丝盘绕机 welding wire coiler焊条压涂机 welding electrode extrusion press 红外线加热器 infra-red heater干燥箱 dryer焊条保温筒 thermostat for electrode流量计 flow meterCO2预热器 CO2 heaterCO2干燥器 CO2 desiccator焊接电缆 welding cable电缆夹头 welding connector地线 earth lead地线夹头 earth clamp焊接参数记录仪 welding parameter recorder 焊缝检测规 weld gauge喷嘴通针 tip cleaner测温笔 tempil stick超声波点焊 ultrasonic spot welding超声波缝焊 ultrasonic seam welding超声波点焊机 ultrasonic spot welder超声波缝焊机 ultrasonic seam welder冷压焊 cold pressure welding (CPW)热压焊 hot pressure welding热轧焊 hot roll welding旋弧压力焊 rotating arc pressure welding埋弧压力焊 submerged arc pressure welding电渣压力焊 electroslag pressure welding气压焊 gas pressure welding锻焊 forge-welding/ blacksmith welding磁力脉冲焊 magnetic-pulse welding硬钎焊 brazing软钎焊 soldering烙铁钎焊 iron soldering火焰钎焊 torch brazing/ torch soldering热风钎焊 hot gas soldering感应钎焊 induction brazing电阻钎焊 resistance brazing接触反应钎焊 contact-reaction brazing电弧钎焊 arc brazing浸渍钎焊 dip brazing/ dip soldering盐浴钎焊 saltbath dip brazing (soldering)金属浴钎焊 molten metal bath dip brazing炉中钎焊 furnace brazing/ furnace soldering保护气氛钎焊 brazing in controlled atmosphere 敲渣锤 chipping hammer焊接衬垫 backing/ welding backing保留垫板 fusible backing/ permanent backing 临时垫板 temporary backing焊剂垫 flux backing惰性气体衬垫 inert-gas backing引弧板 run-on tab/ end tab/ starting weld tab 引出板 run-off tab/ end tab定位板 strong-back加强勒 stiffener嵌条 insert套环 ferrule面罩 helmet滤光镜片 filter glass/ welding glass防护镜片 cover glass/ plain glass气焊眼镜 welding goggles焊接机器人 welding robot点焊机器人 spot welding robot弧焊机器人 arc welding robot切割机器人 cutting robot焊接机器人生产线 robot line for welding焊接机器人工作站 welding robot station机器人运动自由 degree of free for robot机器人工作空间 robot working space轨迹重复精度 path repeatability点位重复精度 PTP repeatability焊接专家系统 welding expert system真空钎焊 vacuum brazing蒸气钎焊 vapor phase soldering超声波钎焊 ultrasonic soldering扩散钎焊 diffusion brazing波峰钎焊 flow soldering/ wave soldering分级钎焊 step brazing/ step soldering不等间隙钎焊 brazing with the unparalleled clearance红外线钎焊 infra-red brazing (soldering)光束钎焊 light soldering (brazing)激光钎焊 laser brazing (soldering)电子束钎焊 electron beam brazing钎接焊 braze-welding钎料 brazing filler metal/ solder硬钎料 brazing filler metal软钎料 solder (m)自钎剂钎料 self-fluxing brazing alloy/ self-fluxing filler metal活性钎料 active filler metal/ active metal brazing alloy成形钎料 preformed filler metal/ solder preform 非晶态钎料 amorphous filler metal粉状钎料 powdered filler metal钎料膏 braze cream/ braze paste/ solder cream/ solder paste药皮钎料 flux coated brazing(soldering)rod层状钎料 sandwich filler metal药芯钎料丝 flux-cored colder wire 焊接机器人示数 welding robot play back焊接图象识别 pattern recognition for welding焊接图象处理 welding image processing计算机辅助焊接工艺设计 computer-aided welding process programming (CAWPP)计算机辅助焊接结构设计 computer-aided design for welding structure焊接烟尘 weld fume焊接发尘量 total amount of fumes焊接烟尘浓度 weld fume concentration焊接烟尘容限浓度 threshold limit values of weld fume (TLV)焊接发尘速率 weld fume emission rate焊接有害气体 welding toxic gases/ weld harmful gases 标定卫生空气需要量 nominal hygienic air requirement 焊工尘肺 pheumocomsis of welder焊工锰中毒 chronic occupational manganese poisoning of welder焊工氟中毒 fluorosis of welder焊工金属烟热 metal fume fever of welder电光性眼炎 eye-flash (arc eye)电光性皮炎 electro-photo dermatitis电弧紫外线灼伤 ultraviolet ray burn防电击装置 voltage reducing device除尘装置 dust collection device焊工手套 welding gloves护脚 welding spats防护鞋 shielding shoes敷钎料板 clad brazing sheet钎剂 brazing flux；soldering flux气体钎剂 gas flux反应钎剂 reaction flux松香钎剂 colophony flux；rosin flux钎剂膏 flux paste阻流剂 stopping-off agent钎剂活性 flux activity钎剂活性温度范围 activation temperature range of flux钎剂热稳定性 thermal stability of flux钎焊过程 brazing (soldering) process钎焊操作 brazing (soldering) operation（焊接网 ）工艺镀层 technological coating钎焊面 faying face钎缝间缝 joint gap；joint clearance钎焊参数 brazing process variables钎焊温度 brazing temperature钎焊时间 brazing time钎焊保温时间 holding time of brazing钎缝 brazing seam；soldering seam钎缝界面区 interfacial region钎缝金属 brace metal钎角 fillet钎焊接头 braced joint；soldered joint平面搭接头 joggled lap joint；flush lap joint 焊接欠缺 welding imperfection焊接缺陷 weld defect气孔 blowhole/ gas pore针尖状气孔 pinhole密集气孔 porosity条虫状气孔 wormhole裂纹 crack表面裂纹 surface crack咬边 undercut焊瘤 overlap凹坑 pit烧穿 burn through塌陷 excessive penetration未焊透 incomplete penetration/ lack of penetration 未熔合 lack of fusion/ incomplete fusion未焊满 incompletely filled weld根部凹陷 root concavity电弧擦伤 arc scratch夹渣 slag inclusion夹杂物 inclusion夹钨 tungsten inclusion白点 fish eye/ flake错边 misalignment/ dislocation试件 test piece试样 test specimen无损检验 nondestructive test破坏检验 destructive test搭接对接接头 butt and lap joint搭接T 形接头 lapped T-joint ；flanged T-joint 锁缝接头 folded joint平面锁缝接头 lick side seam joint ；flat lock seam joint锁缝角接接头 lock corner joint ；corner double seam 嵌入T 形接头 inset T joint T 形管接头 branch T saddle joint 套管接头 socket joint外喇叭口套管接头 flare tube fitting 扩口套管接头 spigot joint 钎焊性 brazability ；solderability 润湿性 wettability润湿角 wetting angle ；contact angle 铺展性 spreadability铺展系数 spread factor ；coefficient of spreading 钎着率 brazed rate脱钎 de-brazing ；de-soldering 润湿称量试验 wetting balance test 铺展性试验 spreadability test 填缝性试验 clearance fillability test 未钎透 incomplete penetration 虚钎 cold soldered joint 钎料熔析 liquation of filler metal 溶蚀 erosion钎料流失 brazing filler metal erosion 钎剂夹杂 flux inclusion外观检查 visual examination 超声波探伤 ultrasonic inspection 直射法超声波探伤 straight beam method斜射法超声波探伤 angle beam method 液浸法超声波探伤 immersion method射线探伤 radiographic inspection/ radiography X 射线探伤 X-ray radiographic inspection γ射线探伤 gamma-ray inspectionX 射线工业电视探伤 X-ray industrial television inspection磁粉探伤 magnetic particle inspection电磁探伤 electromagnetic inspection/ eddy current test 探伤灵敏度 flaw detection sensitivity 渗透探伤 penetration inspection 荧光探伤 flurescent penetrant inspection 着色探伤 dye penetrant inspection 密封性检验 leak test 气密性检验 air tight test 枕形气密检验 pillow test 耐压检验 pressure test 水压检验 hydraulic test 气压检验 pneumatic test 液晶检验 liquid crystal test声发射检测 acoustic emission testing 面弯试验 face bend testing 背弯试验 root bend test 侧弯试验 side bend test晶间渗入 intergranular penetration波峰钎焊机 wave soldering machine冷壁真空钎焊炉 cold wall type vacuum brazing 热壁真空钎焊炉 hot wall type vacuum brazing furnace钎焊盒 brazing retort钎剂涂敷器 fluxer钎炬 brazing (soldering) blowpipe喷灯 brazing lamp烙铁 solder iron热喷涂 thermal spraying火焰喷涂 flame spraying电弧喷涂 electric arc spraying等离子喷涂 plasma spraying高频感应喷涂 high frequency spraying气体爆燃式喷涂 detonation flame spraying 横弯试验 horizontal bend test 纵弯试验 axial bend test压扁试验 squeezing testinert-gas-arc-welding 惰性气体弧焊,惰性气体保护焊hard-to-weld 难焊接的可焊性差的weld-all-over 全周焊接，全部焊接V-weld V形坡口(对接)焊缝butt-weld 以对头焊接接合welding 焊接法, 定位焊接U-weld U形(坡口)焊接x-weld X型(坡口)焊缝cast-weld 铸焊,浇注焊接doubleU-weld 双U形坡口焊（焊接网welded rod 焊接篦条；焊接篦条,焊接筛条weld nugget 点焊焊点；点焊焊点,点焊熔核welding terminals 电焊机接线端，电焊机接线端子weld pass 焊接道次；焊接道次,焊接次数scarf weld 斜面焊接, 两端搭接焊, 嵌接焊scarf welding 两端搭接焊, 嵌焊, 斜面焊接atomic-hydrogen welding 核氢焊,核氢焊机,氢原子电弧焊weld area 焊接部位；焊接部位,焊缝区linde welding 林德钢管对焊法,林德钢管对焊法flush weld 齐平焊缝,平焊,削平补强的焊缝 ）tack-weld 点焊，定位焊all-welded 全焊体全焊的oxy-welding (氧)气焊butt-welded 对接焊接的press-welding 压焊，冷焊spot-weld vt 点焊l.w.|lap-welded 搭接焊的 lap-welded 搭接焊的space-welding 间隔焊接weld-edgewise 沿边焊forge-welding 锻焊welding-lead 电焊引线crotch-weld 楔接焊接weld-nut 焊接螺母arc-welding 电弧焊接weld-time 焊接时间welding-position 焊接位置intermittent-weld 断续焊接automatic-welding 自动焊接welding-stress 焊接应力welding-flame 焊接火焰welding-symbol 焊接符号welding-equipment 焊接设备weld-spacing 焊接间距butt-resistance-welding 电阻对焊welding-sequence 焊接顺序autogenous-welding 氩氧锂接welding burner 焊工喷燃器,焊焊枪嘴,焊接喷灯resistance welding 电阻焊，电阻焊接，接触焊接bridge welding 加搭板对接点焊,加搭板对接滚焊welding die 接触板；接触板,凸焊用电极flux-cored welding 管状焊丝电弧焊,药芯焊丝电弧焊welding process 焊接法，焊接过程，焊接方式electropercussive welding 电冲击焊, 电接触焊, 电点焊pressure welding 压焊，压力焊接，加压焊接weld preparation 开焊接坡口，焊接接头准备welding ground 电焊(接)地线，焊接地线unionare welding 磁性焊剂二氧化碳气体爆ず附樱weld together 焊接起来,使结合在一起arc welding 电炉焊接,电弧焊；电弧焊backhand welding 反手焊接,右向焊,后退式气焊intermittent welding 断续焊，间断焊，断续焊接scarf weld 斜面焊接,两端搭接焊,嵌接焊welding powder 焊粉；焊粉,粉状焊接熔剂welding point 焊拉点；焊拉点,焊接位置closed-butt weld 密接对接焊缝,无间隙对接焊缝welding pressure 电极压力,镦粗压力，顶锻压力stick welding 气体保护金属极电弧焊,粘结焊commutator-controlled welding 换向控制焊接,可控整流器焊接horizontal-rolled-position welding 横向滚动位置焊接,滚动水平焊torch welding 气炬焊接，气炬焊扫，气焊welded joint 焊缝，焊接接头，焊接接合tight-weld 密封焊性weld-length 焊缝长度welding-symbols 焊接符号welding-current 焊接电流welding-ground 电焊地线weld-size 焊接尺寸explosive-welding 爆炸焊接welding-source 焊接电源friction-welding 摩擦焊接seam-welding 缝焊,滚焊ultrasonic-welding 超声波焊接bead-weld 珠焊,堆焊horizontal-welding 横焊,平焊forge-welding 锻接,锻焊welding-flux 焊剂,焊料welding-transformer 焊接变压器weld-penetration 熔深,熔透blacksmith-welding 锻接,锻焊forge-weld 锻接,锻焊enclosed-welding 强制成形焊welding 焊接法,粘结weld 焊接,焊接点welding-head 焊头,烙铁头fillet-welding 填角焊,条焊butt-welding 对焊,对接焊forward-welding 前进焊,左焊butt-weld 对接焊,对焊welding generator 电焊发电机，焊接用发电机mash welding 交叉焊条式压薄点焊,压薄滚焊edge weld 边缘焊缝，端焊接，端焊缝field weld 安装焊接装配焊接工地焊接Welding Association 德国焊接技术协会[联邦德国] welding rectifier 电焊整流器，焊接整流器cascade welding 阶梯形多层焊, 串级叠置焊welding station 焊接室；焊接室,焊接台meshed weld 压边焊接焊缝,啮合焊接焊缝single-fillet weld 单边角接焊缝,单面填角焊缝plasma-arc welding 等离子弧焊接,等离子电弧焊girth welding 环缝焊接,环形焊缝焊接TIG welding 钨极惰性气体保护电弧焊TlG-arc welding 钨极惰性气体保护电弧焊air-hydrogen welding 空气-氢焊接submerged-arc welding 焊剂层下焊接beading weld 窄焊缝,珠焊welding bench 焊接工专weld throat 焊缝厚度hf welding 高频焊接welding engineering 焊接工程welding section 焊接断面inverted weld 凹面焊缝jump-welded pipe 对缝焊管intermittent weld 断续焊缝butt-welded tube 对缝焊管forged weld 锻接焊缝block-sequence-welding 多段多层焊接法welded-joint 锻焊缝,锻接头seal-weld 密封焊,封闭焊percussion-welding 冲击焊,储能焊butt-seam-welding 对缝焊,对线焊welding-torch 焊接吹管,焊矩weld-zone 焊接区,焊接处thermit-welding 铝热焊,热剂焊tack-welding 点固焊,平头焊接fusion-welding 熔焊接,熔融焊接backstep-welding 后退焊接,分段退焊welding-force 阻焊加压,电极压力edge-weld 边缘焊接,端接焊接flash-welding 闪光焊接,闪光对焊upset-welding 电阻对焊,镦压焊接welded-pipe 锻接管,压力焊接管backhand-welding 后退焊接,反手焊接tack-weld 定位焊点,点固焊点discontinuous-welding 断续焊接,间断焊接as-welded 熔接状态,焊接状态welding-shop 焊接车间,焊接工场welding-leads 电焊引线,焊机电缆线pulsation-welding 脉冲焊接,多脉冲焊接strength-weld 高强度焊接,强密焊接fillet-welding-joint 填角焊缝接头,角焊接头parallel-welding 直接焊珠焊接,焊珠焊接weld 熔焊,结合；焊接,焊skip weld 间断焊缝welding characteristics 焊接特性weld flaw 焊接缺陷welding deformations 焊接变形welded frame 焊接骨架profection welding 凸出焊接welding department 焊接车间welding strees 焊接应力helical welding 螺旋焊接groove-welded joint 坡口焊缝welding characteristic 焊接性能blacksmiths weld 锻焊接头weld failure 焊缝开裂pipe welding 管路焊接weld hardening 焊接硬化backup weld 封底焊缝weld spatter 焊接飞溅weld metallurgy 焊接冶金back-step welding 分段退焊welding tangs 焊接夹钳frection welding 摩擦焊roll welding 滚压焊butt-welded seam 对焊缝union-melt welding 埋弧焊welding clamp 电焊夹头all-around weld 整周焊缝welding factor 焊接系数welded 熔焊,结合；焊接的welded 熔焊(结合)；焊接的manual-welding 手焊接resistance-welding 电阻焊welding-machine 焊接管weld-line 焊接线welding-heat 焊接热welding-operator 焊接工block-welding 块焊接welding-rod 焊条welding 焊接fusion-weld 熔焊slot-welding 槽焊gas-welding 气焊spot-welding 点焊skip-welding 跳焊smith-welding 锻焊lap-welding 搭焊plug-welding 塞焊flush-weld 平焊flat-welding 平焊manual-weld 手焊electric-welding 电焊spot-weld 焊点slot-weld 槽焊pressure-welding 压焊projection-weld 凸焊weld dressing 清理焊烽welding rules 焊接规则weld crosswise 交叉焊接double-vee weld X形焊缝flash butt-welding 闪光对接焊one-pass weld 联合筑路机full-penetration weld 全焊透焊缝welding gutter 焊管拉模welding crack 焊接裂纹weld cracking 焊缝破裂backing weld 底层焊接backing welding 底层焊接hand welding 手工焊接weld wire 包铜钢丝welding code 焊接规范welding cycle 焊接周期ripple weld 鳞纹焊缝welding mask 焊接面罩weld cycle 焊接周期weld jig 焊接夹具welding atmosphere 焊接气氛welding amperage 焊接电流welding voitage 焊接电压multilayer welding 多层焊接overhead weld 仰焊焊缝welding data 施焊工艺条件flash butt-weld 闪光对接焊缝mig welding 惰性气体保护金属极电极弧焊；米克焊接；金属惰性气体保护焊接,惰性气体保护金属极焊接machine welding 机械焊接，机械化焊接，自动焊接，自动焊，机械(化)焊（焊接网 ）mag welding 活性气体保护金属极焊接；MAG焊,活性气体保护电弧焊welding inspector 焊接工段检验员；焊接工段检验员,焊件检查员tack weld 点住焊，定位焊，定位焊点，定位焊接，钉焊mesh weld 压边焊接焊缝；压边焊接焊缝,啮合焊接焊缝welding head 烙铁头，焊枪，(自动电焊机的)机头，焊机头aircomatic welding 自动调弧氩弧焊, 惰性气体保护金属极弧焊welding outfit 焊接配备；焊接设备,焊机，焊接装置shallow weld 浅熔焊焊缝；浅熔焊焊缝,末焊透焊缝aircomatic welding 自动调弧氩弧焊,惰性气体保护金属极弧焊site welding 安装焊接,工地焊接,现场焊接,安装焊接heliarc welding 海利亚克法焊接；赫利焊接,氦气保welding precaution 焊接预防措施structural welding 建筑结构焊接oxy-hydrogen welding 氢氧焰焊接incomplete-penetration weld 未焊透焊缝sagged weld 成凹陷焊缝directarc welding 直接电弧焊multiple-row weld 多排焊接头girth weld 环形焊缝around weld 周围焊缝gas-welding flame 气焊火焰puddle welding 堆焊,熔焊hammer weld 锻接,锻程plasma welding 等离子焊接welding metallurgy 焊接冶金学welded break 捍接断裂处welding mill 焊管机welding grade 焊接级blacksmith's weld 锻焊缝gas-welding heat 气焊热welding pool 焊接池two-axis welding 双轴焊welding leads 焊接铅vibration welding 振动焊tape welding 带焊接welding shaft 焊接轴gas welded 气焊的welded bridge 焊接桥护焊接sealing weld 封底焊缝，密封焊缝，密封焊，封底焊rod welding 焊条焊,特种成分的焊条作为焊接的填充料back weld 封底焊缝，封底焊背面焊缝，背面焊welding torch 焊接喷灯，焊接吹管，焊炬，气焊嘴welded chert 熔合燧石；玉髓燧石,红色豆粒燧石horizontal welding 横焊，水平焊，水平焊接，横向焊接butt weld 对焊,对接焊缝；对接焊,对头焊缝Sigma welding 惰性气体保护金属极弧焊, 西格马焊接welding regulator 焊接气体减压器，焊接电流调节器spot weld 点焊缝，点焊接(电阻焊的一种) welding converter 焊接变流机；焊接变流机,电焊机wandering welding 分段跳焊；分段跳焊,分散间隔焊series welding 单边多电极焊接, 串焊, 系列焊接flash welding 火花〔电弧,闪光〕焊,电弧对焊接weld porosity 焊缝气孔；焊缝气孔,焊缝孔隙bevel weld 坡口焊缝,铲边焊缝；斜角焊缝welding goggles 焊工护目镜；黑玻璃,滤色玻璃forge welded 锻焊的pipeline welding 管线焊aluminithermic weld 铝热焊接dry weld 干式焊件production weld 制品焊接hydrogen welding 氢焊接。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
K形坡口
Double Bevel Groove
86
Z形坡口
Z-Type Groove
87
Y形坡口
Single V Groove with Broad Root Face
88
焊缝
Weld
89
焊缝代号
Welding Symbol
90
焊缝金属
Weld Metal
91
填充金属
Filler Metal
92
熔化系数
Melting Coeffcient
65
熔敷系数
Deposition Coeffcient
66
熔敷效率
Deposition Efficiency
67
飞溅
Spatter
68
熔合比
Penetration Ratio
69
稀释
Dilution
70
稀释率
Rate of Dilution
71
合金过渡系数
43
焊接条件
Welding Condition
44
焊接工艺参数
Welding Parameter (Welding Condition)
45
焊接电流
Welding Current
46
极性
Polarity
47
正接
Electrode Negative (Straight Polarity)
48
反接
Electrode Positive (Reversed Polarity)
熔敷金属
Deposited Metal
93
焊缝正面
Face of Weld
94
焊缝背面
Back of Weld
95
焊缝轴线
Axis of Weld
96
焊趾
Toe of Weld
97
焊缝宽度
Weld Width
98
焊缝长度
Weld length
99
焊缝厚度
Throat Depth(Throat Thickness)
Multi-Layer Welding
30
打底焊
Backing Welding
31
封底焊
Back Sealing Welding
32
左焊法
Leftward Welding
33
右焊法
Rightward Welding
34
自动焊
Automtic Welding
35
半自动焊
Semi-Automtic Welding
49
电流密度
Current Density
50
电弧电压
Arc Voltage
51
焊接速度
Welding Speed
52
线能量
Heat Input (Energy Input)
53
预热
Preheat
54
后热
Postheat
55
焊后热处理
Postweld Heat Treatment
56
预热温度
Preheat Temperature
100
焊缝成形系数
Form Factor of Weld
101
熔深
Penetration(Depth of Penetration)
102
焊缝成形
Appearance of Weld
103
余高
Reinforcement(Excess Weld Metal)
常用的焊接名词中英文对照表
常用的焊接名词中英文对照表
注：圆括号内为同义词，方括号内为可省略。
序号
焊接名词（中文）
焊接名词（英文）
1
焊接
Welding
2
熔焊
Fusion Welding
3
压焊
Pressure Welding
4
钎焊
Brazing and Soldering
5
焊接过程
Welding Process
17
立焊位置
Vertical Position of Welding
18
仰焊位置
Overhead Position of Welding
19
对接焊
Butt Welding
20
角焊
Fillet Welding
21
搭接焊
Lap Welding
22
船形焊
Fillet Welding in the Downhand (Flat) Position
57
后热温度
Postheating Temperature
58
层间温度
Interpass Temperature
59
焊丝伸出长度
Wire Extention
60
弧长
Arc Length
61
熔化速度
Melting Rate
62
熔化时间
Melting Time
63
熔敷速度
Deposition Rate
64
36
手工焊
Manual (hand) Welding
37
堆焊
Surfacing (Overlaying)
38
塞焊
Plug Welding
39
槽焊
Slot Welding
40
焊剂垫
Flux Backing
41
焊剂垫焊
Welding with Flux Backing
42
窄间隙焊
Narrow-Gap Welding
6
焊接技术
Welding Technique
7
焊接工艺
Welding Technology (Welding Procedure)
8
焊接操作
Welding Operation
9
焊接顺序
Welding Sequence
10
熔敷顺序
Build-up Sequence
11
焊接方向
Direction of Welding
12
焊接位置
Position of Welding
13
焊缝倾角
Weld Slope (Inclination of Weld Axis)
14
焊缝转角
Weld Rotation (Angle of Rotation)
15
平焊位置
Flat Position of Welding
16
横焊位ng
77
卷边高度
Height of Flange
78
单面坡口
Single Groove
79
双面坡口
Double Groove
80
I形坡口
Square Groove
81
V形坡口
Single V Groove
82
U形坡口
Single U Groove
83
J形坡口
Single J Groove
84
X形坡口
Double V Groove
Transfer Efficiency (Recovery[of an Element])
72
坡口
Groove
73
坡口角度
Included Angle
74
钝边
Root Face
75
钝边高度
Thickness(Width) of Root Face
76
根部间隙
Root Gap (Root Opening)
23
定位焊
Tack Welding
24
单面焊
Welding by One Side
25
双面焊
Welding by Both Sides
26
单道焊
Single-Pass (-Run) Welding
27
多道焊
Multi-Pass Welding
28
单层焊
Single-Layer Welding
29
多层焊