世伟洛克阀门样本
计量阀(流量阀)世伟洛克MS-01-142[1]
![计量阀(流量阀)世伟洛克MS-01-142[1]](https://img.taocdn.com/s3/m/e2efef06f12d2af90242e61f.png)
S 系列直通型 1.56 1.90 2.04 2.34 (59.4) 1.90 2.04
(39.6) (48.3) (51.8) (48.3) (51.8)
—
0.38
(9.6)
0.45
(11.4)
0.92
(23.4)
外螺纹 VCR 1/4 in. SS-SVR4 接头 1/16 in. 1/8 in. 世伟洛克 卡套管接头 1/4 in. 3 mm SS-SS1-A SS-SS2-A SS-SS4-A SS-SS3MM-A
最大流量 —— 0.16 Cv
至大气压 的压降 psi (bar) 10 (0.68) 50 (3.4) 100 (6.8) 空气流量 std ft3/min
(std L/min)
(35.1)
1.38
流量系数 (Cv)
水流量 U.S. gal/min
(L/min)
2.0 (56.6) 6.4 (181) 11.4 (323)
1
A
S 系列
M 系列 阀体材料 黄铜
L 系列 材料等级/ ASTM 规范 酚醛/D4617 镀镍镉钢 316 SS/A276 PTFE/D1710 316 SS/A276 440C SS/A276 316 SS/B783 316 SS/A276 316 SS/A479
316 SS 材料等级/ASTM 规范 300 SS/A276
316 SS/A182
带碳氢化合物载体的 镍防卡死剂
润滑剂
润湿元件用 斜体 表示。 ➀ 厌氧型粘结剂。 ➁ 直通型和双重型 M 系列阀。 ➂ 角 型和交叉型 M 系列阀门不包括阀体密封。
二硫化钼基；硅基
测试
每个世伟洛克S、 M和L系列计量阀都在工厂在 1000 psig (69 bar) 的条件下用氮气进行了测试.对壳体也按照检测不到泄 漏的要求用检漏液进行了测试. 每个世伟洛克L系列计量阀都在100 psig (6.8 bar) 的差压下进 行了无气泡阀座关闭测试. 世伟洛克的每一 31 系列针阀都在 1000 psig (69 bar)压力下进 行氮气测试。 阀座的最大容许泄漏率为 0.1 std cm3/min。
世伟洛克
W65
SS-51K-W65-BK
67, 68 67, 68 3 通 T67M, T68M
SS-51K-67-BK SS-51K-67X-BK SS-51K-67
尺寸，in. (mm)
A
B
C
2.37 (60.2)
0.69 (17.5)
0.98 (24.9)
4.50 (114)
6.00 (152)
9.14 (232)
W63
SS-51K-W63K-OG
65 65 3 通 T65M
SS-51K-65K-OG SS-51K-65XK-OG SS-51K-65K
W65
SS-51K-W65K-OG
67, 68 SS-51K-67K-OG 67, 68 3 通 SS-51K-67XK-OG T67M, T68M SS-51K-67K
杆式手柄成套件订购号
4 螺栓阀门
8 螺栓阀门
SS-51K-62L-BK
SS-51K-S62L-BK
SS-51K-62XL-BK
—
锁定支架可以把阀门锁定在开或关位置，适合直径小于如下尺 寸的钩环： ■ 0.344 in. (8.7 mm)—62, 63 和 65 系列 ■ 0.375 in. (9.5 mm)—67 和 68 系列 带锁定支架的阀门不能面板安装。
A-88 球阀
工艺球阀手柄选购件
手柄成套件和工厂安装的手柄
■ 杆式和椭圆形手柄 ■ 杆式和椭圆形手柄的锁定支架 ■ 椭圆形闩锁手柄
60 系列阀门手柄
60 系列球阀的标准配置是杆式手柄。还可提供: ■ 椭圆形手柄 ■ 杆式和椭圆形手柄的锁定支架 ■ 椭圆形闩锁手柄 ■ 备用乙烯树脂衬套。
杆式手柄
世伟洛克针阀资料(中文)
➁ O、 20 和 1 系列带有 0.172 in. (4.4 mm) 孔口 — 2 双弹簧；
18、 26, 和 1 系列带有 0.250 in. (6.4 mm) 孔口 — 3 弹簧。
➂ 可调和 V 形阀杆尖和螺纹;软座阀杆螺纹。
测试
每个整体式阀帽针阀都在工厂用 1000 psig (69 bar) 下的氮进行 过测试。阀座的最大可允许漏泄率为 0.1 标准 cm3/min。壳体 测试是根据使用检漏液时无可探测出的泄漏的要求进行的。
O、1 和 18 系列
ASME 级别 材料级别 材料名称 温度，°C (°F) –53 (–65) 至 –28 (–20) –28 (–20) 至 37 (100) 93 (200) 121 (250) 148 (300) 176 (350) 204 (400) 232 (450) 260 (500) 315 (600) 5000 (344) 5000 (344) 4295 (295) 4085 (281) 3875 (266) 3715 (255) 3560 (245) 3435 (236) 3310 (228) 3130 (215) 2080 2.2 316 SS 铜 3000 (206) 3000 (206) 2350 (161) 2200 (151) 2050 (141) 1470 (101) 390 (26) — — — N/A N/A 钢 — 3000 (206) 2730 (188) 2695 (185) 2660 (183) 2615 (180) — — — — 工作压力，psig (bar) 3000 (206) 3000 (206) 2640 (181) 2555 (176) 2470 (170) 2430 (167) 2390 (164) 2380 (163) 2375 (163) — 1500 3.4 合金 400
swagelok
(38.9)
1.53
(63.5)
2.50
25/32 面板孔
(19.8)
0.19 (4.8) 最大面板 厚度
SWAGELOK
B A
所示尺寸是世伟洛克卡套管接头螺母用手指旋紧时的尺寸。 ➀ 可订购带有两种不同端接的 SK 系列阀。 关于订购信息可与您当地授权的世伟洛克公司代表联系。 ➁ 参阅规范 ISO 7/1、 BS EN 10226-1, DIN-2999 和 JIS B0203。 ➂ 标准阀门上的 VCO 接头包括低温碳氟化合物 FKM O-型圈。
316 SS / A479 PTFE 基 具有烃粘合剂涂层的二硫化钼
13 15 18
订购信息与尺寸
选择一个订购号。 以 in. (mm) 为单位表示的尺寸仅供参考， 可能有变动。
端接➀ 类型 世伟洛克 卡套管接头 内螺纹 NPT 内螺纹 ISO➁ 外螺纹 NPT 外螺纹 VCO 接头➂ 尺寸 1/4 in. 3/8 in. 6 mm 8 mm 1/4 in. 1/4 in. 1/4 in. 1/4 in. 订购号 SS-4SKPS4 SS-4SKPS6 SS-4SKPS6MM SS-4SKPS8MM SS-4SKPF4 SS-4SKPF4RT SS-4SKPM4 SS-4SKPVCO4 Cv 1.3 1.4 1.3 1.3 1.2 1.2 1.1 0.9 0.188 (4.8) 孔径 尺寸, in. (mm) A 3.60 (91.4) 3.73 (94.7) 3.60 (91.4) 3.68 (93.5) 2.91 (73.9) 2.91 (73.9) 3.23 (82.0) 3.15 (80.0) B 1.80 (45.7) 1.86 (47.2) 1.80 (45.7) 1.84 (46.7) 1.46 (37.1) 1.46 (37.1) 1.62 (41.1) 1.58 (40.1)
世伟洛克swagelok40和40G系列一体式仪表球阀
上海别众实业有限公司 电话：021-59742356 传真：021-59747932 邮箱：mgd@ 网址：/
仪表球阀—40G 系列和 40 系列
303
目录
世伟洛克® (Swagelok®)仪表球阀 . . . . . . . . . . . . . . . . 303 有关世伟洛克仪表球阀 的重要信息 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303 特点 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 304 结构材料 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305 压力—温度额定值 . . . . . . . . . . . . . . . . . . . . . . . . . . . 306 在 20°C (70°F) 时的流量数据 . . . . . . . . . . . . . . . . . . 306 测试 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306 清洁和包装 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306 开关 (2 通) 阀门 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 307 切换 (3 通) 阀门 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309 切换 (5 通和 7 通) 阀门 (40 系列) . . . . . . . . . . . . . . . . 311 交叉转换 (4 通和 6 通) 阀门 (40 系列) . . . . . . . . . . . . 312 手柄选购件 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313 排放口和阀杆延长选购件 . . . . . . . . . . . . . . . . . . . . . . 315 附件 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315 气动执行机构 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 316 符合 ISO 5211 标准的气动执行机构 . . . . . . . . . . . . . 319 用于气动执行机构的选购件 . . . . . . . . . . . . . . . . . . . . 321 电动执行机构 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322 工艺选项 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323 服务选项 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323 流动路径选项 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 324 订购多种选购件和附件 . . . . . . . . . . . . . . . . . . . . . . . 328
swagelok安全阀
设定压力和再密封压力
■ 设定压力是首次有流体流出时的上游压力。 室温下 ， 初始卸荷完成
背压
高压阀 (R3A 和 R4 系列)
通过这些高压阀的设计使系统背压的影响减至最小。
后， 每个阀门的设定压力在 ± 5 % 范围内可重复。
■ 再密封压力是无流体流出时的上游压力， 再密封压力总是低于设
定压力。
碳氟 FKM
316 SS/A479 316 SS/A182
9 10 11 12
润滑剂
二硫化钼基干燥薄膜 和湖剂；硅酮基
仅
R4
润湿元件用斜体字列出。 ➀ 可要求提供粘结剂的材料安全数据表。
12a
13 19
RL3
R3A
RL4
R4
比例卸荷阀
20°C (70°F) 时流量数据
空气
RL3 和 RL4 系列
系列 RL3, RL4 R3A, R4
所需的设定压力是 120 psig. 系统背压是 40 psig。 步骤 1. 将背压乘以 0.8。 40 psig 3 0.8 = 32 psig。 步骤 2. 将结果从所需的设定压力中减去。 120 psig – 32 psig = 88 psig。 步骤 3. 把比例卸荷阀预设于 88 psig.
仅
R3A
7
12a 粘结杆 13 粘结盘 14 阀座 15 垫片
碳氟 FKM－粘结➀ 316 SS/A479
316 SS/A479 PTFE 涂层 316 SS/A240 316 SS/A479
12 13 14 15
19
12 16 17 18
8
16 阀座护圈 17 O 型圈 18 插入件 19 阀体
元件 1 塞头 2 帽盖 3 标签 4 锁紧螺母 5 弹簧 6 衬套 材料等级/ASTM 规格 RL3，R3A—镀镍黄铜； RL4，R4—黄铜 316 SS/A479 聚酯 RL3，R3A—粉末金属， 300 系列 SS/B783； RL4，R4—316 SS/A276 S17700 SS/AMS 5678 304 SS/A240 RL3，R3A—粉末金属， 300 系列 SS/B783； RL4，R4—316 SS/A276 316 SS/A479
世伟洛克 40G,40,60,83系列 和 AFS 球阀 说明书
适用于世伟洛克球阀的符合 ISO 5211 的执行机构 A-97A40G, 40, 60, 83 系列和 AFS 球阀■ 气动齿轮、齿条执行机构■ 执行机构符合行业接口标准：ISO 5211, NAMUR 和 VDI/VDE 3845■ 可提供工厂装配好的成品或供现场装配的成套件适用于世伟洛克球阀的符合 ISO 5211 的执行机构A-98 球阀A符合 ISO 5211 的世伟洛克齿条和齿轮气动执行机构适用于一般应用。
提供直通阀和角型阀用弹簧回程和双作用模式的产品。
世伟洛克可提供符合 ISO 5211、NAMUR 和 VDI/VDE 3845 接口标准的带全部执行机构的球阀组件、包括阀门、执行机构、传感器、支架成套件和电磁阀。
本产品目录所列阀门执行机构组件的设计条件是：■ 最高阀门压力■ 环境温度 (10 到 37°C [50 到100°F])■ 设计余量为计算操作扭矩的 20%。
欲获得关于阀门操作扭矩计算的更多信息、请参阅世伟洛克带执行机构的球阀选型指南、符合 ISO 5211 的执行机构安装支架成套件、P A-105。
执行机构工作额定值最大的执行机构压力是 116 psig (8 .0 bar)。
证书对于工厂装配的符合 ISO 5211 的世伟洛克执行机构、可在订单报价时要求提供 ATEX 认证。
现场装配不提供 ATEX 认证。
执行机构结构材料还可以提供更多材料。
请联系您的授权世伟洛克代表。
执行机构安装支架阀门阀门接地弹簧电磁阀安装支架位置指示器接头阀杆螺母锁定片固定螺钉接头面板螺母40G, 40, 83, H83 系列AFS 球阀60 系列 4 螺栓铸造不锈钢墙壁安装支架六角螺栓有头螺钉六角 螺母锁紧垫圈符合 ISO 5211 标准的气动执行机构适用于世伟洛克球阀的符合 ISO 5211 的执行机构 A-99A40G 和 40 系列阀门关于阀门特点、结构材料和技术数据、请参阅世伟洛克产品目录一体式仪表球阀—40G系列和 40 系列, P A-3。
MS-01-146 世伟洛克60系列球阀 60 Series Ball Valve
Ball ValvesGeneral Purposeand Special Application60 Seriess1/8 to 2 in. and 6 to 25 mm sizess Stainless steel, carbon steel, brass, and special alloy materials s On-off (2-way) and switching (3-way) valvess Compensating seat designs Live-loaded, two-piece stem packing260 Series Ball ValvesUnique coned-disc spring-loaded seat s compensates for seat wear, pressure, and temperature changes s reduces seat wear from pressure surges s seals regardless of flow directionSupport ringcontains the seat and protects against seat bulge, premature wear,and deformationSeatFlange sealprovides leaktight seal between flange and center bodyContentsPageFeatures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2Materials of Construction . . . . . . . . . . . . . . . . . . . . . . . . . .4Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Cleaning and Packaging . . . . . . . . . . . . . . . . . . . . . . . . . .5Pressure-Temperature Ratings . . . . . . . . . . . . . . . . . . . . . .6Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8DimensionsSwagelok ®Tube Fitting End Connections . . . . . . . . . . . .9Female Pipe Thread End Connections . . . . . . . . . . . . . .10Tube and Pipe Socket Weld Connections . . . . . . . . . . . .11Pipe Butt Weld Connections . . . . . . . . . . . . . . . . . . . . . .12Tube Extension End Connections . . . . . . . . . . . . . . . . . .13VCO ®and VCR ®Face Seal Fitting End Connections . . .13Sanitary Fitting End Connections . . . . . . . . . . . . . . . . . .14Mixed End Connections . . . . . . . . . . . . . . . . . . . . . . . . .14Special Application ValvesSteam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15Thermal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16Fire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17Chlorine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18All Welded . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18Low Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19Rapid-Cycle Service . . . . . . . . . . . . . . . . . . . . . . . . . . . .19Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20Rack and Pinion Pneumatic Actuators . . . . . . . . . . . . . . . .22Featuress Quarter-turn actuations Stainless steel, carbon steel, brass, and special alloys s Lever, oval, extended oval, and locking handless Variety of end connections in 1/8 to 2 in. and 6 to 25mm sizes s Pneumatic and electric actuatorss Mounting brackets and couplings to enable mounting ofISO 5211 standard actuatorss Optional vent portingOn-Off (2-Way) ValveBallConed-disc springOxygen Service HazardsFor more information about hazards and risks of oxygen-enriched systems, see the Swagelok Oxygen System Safety technical report, MS-06-13.Important Information About Packed Valvess Packing adjustment may be required during the valve’sservice life.s Swagelok ball valves are designed to be operated in a fullyopen or fully closed position.60 Series Ball Valves 3Directional stem flatsshow open or closed positionStem springscompensate for changesin pressure andtemperature, and wearGrounding springgrounds stem to providecontinuity for antistaticprotectionLive-loaded,2-piecechevron stem packings requires less operating torques improves performances compensates for stem wearHigh-strength stem bearingss provide smooth actuations eliminate galling betweenvalve stem and bodys resist wearBottom-loaded stems prevents stem blowouts enhances system safetySwitching (3-Way) ValveAll stainless steel switching ball valves incorporate many ofthe features of the on-off (2-way) design. The one-piece centerbody uses no welding and allows 180°actuation. Theswitching design allows the user to:s divert flow from a common inlet to one of two outletss block flow from one inlet port and bleed out the opposite port.Flexing seat design ensures leaktight seal in both low-and high-pressure systemsUnder low pressure, seals are created by the coned discspring-loaded seats pushing against the ball. Pressure isnot required to create a seal.Under high pressure, the ball is forced downstream, flexing thedownstream seat and creating a seal. The upstream seat alsoflexes with the ball movement and maintains a seal.460 Series Ball ValvesMaterials of ConstructionWetted components listed in italics.➀Special alloy materials available include alloy 400, alloy C-276, alloy 20, alloy 600, and titanium. Contact your authorized Swagelok sales and service representative.➁62 series—no upper stem spring and stop plate integral with handle.➂Valves assembled with pneumatic actuators contain a lock tab (not shown) to secure the nut to the stem.➃Additional materials available; see Additional Seat Materials,below.➄Coated with hydrocarbon rust-preventive compound.➅Coated with molybdenum disulfide with hydrocarbon binder. Alloy X-750—2 bearings; PEEK—1 bearing.➆Additional materials available; see Flange Seal Kits,page 21.➇62 series—material specification is ASTM A574.➈62 series—nuts are grade 4130 or 4140/ASTM A322 or A331.Additional Seat Materials➀Molybdenum disulfide coated.➁62 and 65 series—Grafoil®-lined coned-disc springs; 67 and 68 series—PEEK-lined coned-disc springs.60 Series Ball Valves 5141521201918171613121110987645321TestingPlastic-Seated ValvesEvery 60 series ball valve is factory tested with nitrogen at 1000 psig (69bar) or its maximum workingpressure if less than 1000psig (69 bar).Seats have a maximum allowable leak rate of 0.1 std cm 3/min.Shell testing with nitrogen at 1000 psig (69bar) or the maximum rated pressure if less than 1000psig (69 bar) is performed on 62, 63, and 65 seriesvalves to a requirement of no detectable leakage with a liquid leak detector.Shell testing with water at 1.5 times the maximum working pressure isperformed on 67 and 68 series valves.Special-Application ValvesCertain valves may have different testing requirements, as described in Special-Application Valves.Cleaning and PackagingEvery 60 series ball valve is cleaned in accordance with Swagelok standard cleaning and packaging specification (SC-10). Cleaning and packaging in accordance with Special Cleaning and Packaging (SC-11)to ensure compliance with product cleanliness requirements stated in ASTM G93 Level C is available.Contact your authorized Swagelok representative for more information.Metal-Seated Valves and 3-Way PEEK-Seated ValvesEvery 60 series ball valve is factory tested with nitrogen at 50psig (3.4 bar)for leaktight integrity of the seats as specified by FCI 70-2 Specification Class VI.Shell testing with nitrogen at 1000 psig (69bar) or the maximum rated pressure if less than 1000psig (69 bar) is performed on 62, 63, and 65 seriesvalves to a requirement of no detectable leakage with a liquid leak detector.Shell testing with gas at 1.5 times the maximum working pressure isperformed on 67 and 68 series valves.2322660 Series Ball ValvesPressure-Temperature RatingsPressure-temperature ratings are based on standardmaterials of construction, as listed on page 4 and in the table notes below. Ratings for valves with alternative materials of construction may not match those shown. For example,Reinforced PTFE Seats (60T Series)Ratings based on reinforced PTFE seats and packings and alloy X-750 stem bearings on stainless steel or steel, PEEK stem bearings on brass, and fluorocarbon FKM O-rings.Fastener materials: 316 SS on stainless steel valves and carbon steel grade 8 on steel or brass valves.Steel valves with Swagelok tube fitting end connections: 375°F (190°C) max.Alloy X-750 Seats (60M Series)Ratings based on alloy X-750 seats and stem bearings, reinforced PTFE packings, and fluorocarbon FKM O-rings.Fastener materials: 316 SS on stainless steel valves and carbon steel grade 8on steel valves.Steel valves with Swagelok tube fitting end connections: 375°F (190°C) max.Carbon/Glass PTFE Seats (60C Series)Ratings based on carbon/glass PTFE seats, reinforced PTFE packings, and alloy X-750 stem bearings on stainless steel or steel; PEEK stem bearings on brass;and fluorocarbon FKM O-rings.Fastener materials: 316SS on stainless steel valves and carbon steel grade 8 on steel or brass valves.Steel valves with Swagelok tube fitting end connections: 375°F (190°C) max.2-way, stainless steel 67 and 68 series valves with reinforced PTFE seats are rated at 2200 psig at 100°F (151 bar at 37°C)when assembled with optional cadmium-plated carbon steel grade 8 fasteners.60 Series Ball Valves 7 PEEK Seats (60P Series)Ratings based on PEEK seats, packings, and stem bearings,and fluorocarbon FKM quad-seal flange seals.Fastener materials: 316 SS on stainless steel valves and carbonsteel grade 8 on steel or brass valves.Steel valves with Swagelok tube fitting end connections: 375°F(190°C) max.Polyethylene Seats (60E Series)Ratings based on UHMWPE seats and packings, PEEK stem bearings, and ethylene propylene O-rings.Fastener materials: 316 SS on stainless steel valves and carbon steel grade 8 on steel or brass valves.Steel valves with Swagelok tube fitting end connections: 375°F (190°C) max.Virgin PTFE Seats (60V Series)Ratings based on virgin PTFE seats and packings and alloy X-750 stem bearings on stainless steel or steel, PEEK stem bearings onbrass, and fluorocarbon FKM O-rings.Fastener materials: 316 SS on stainless steel valves and carbon steel grade 8 on steel or brass valves.Steel valves with Swagelok tube fitting end connections: 375°F (190°C) max.Ordering InformationOn-Off (2-Way) ValvesSelect an ordering number from the Dimensions tables starting on page 9.See the table below for availability of other valve body materials. To order, replace SS with B or S. Examples: B-62TS4S-62TS4860 Series Ball ValvesAdditional Seat MaterialsMost valve ordering numbers specify reinforced PTFE seat material. For other seat materials, replace T with the desired designator.Examples: SS-62P S4S-62E S4Switching (3-Way) ValvesSwitching (3-way) valves are available with:s stainless steel valve body materials standard or low-temperature services all seat materials except alloy X-750s bottom end connections shown below at right.To order a switching (3-way) valve with three of the same end connections,insert X into the valve ordering number. Example: SS-62X TF4To order a switching (3-way) valve with a different bottom end connection,insert X into the valve ordering number and add a bottom end connection designator.Example: SS-62X TF4-S4To order three different end connections,contact your authorized Swagelok representative.Cross-Port Mixing of FluidsA spherical ball is available in valves with UHMWPE or PEEK seats to prevent cross-port mixing of fluids. To order, insert O into the ordering number.Example: SS-62X O PF460 Series Ball Valves 9DimensionsDimensions, in inches (millimeters), are for reference only and are subject to change.Swagelok Tube Fitting End ConnectionsDimensions shown with Swagelok nuts finger-tight. See Ordering Information,page 8.Swagelok Hydraulic Swaging UnitWhen installing a Swagelok 60 series ball valve with tube fittings larger than 1 in., the Swagelok MHSU hydraulic swaging unit is needed. The unit swages the ferrules onto the tubing without applying stress to fitting body threads.See the Swagelok Multihead Hydraulic Swaging Unitcatalog, MS-02-154, for more information.All 67 and 68 stainless steel steam and thermal series valves and 67 and 68 series valves with UHMWPE seats are assembled with silver-plated front ferrules. All other 67 and 68 series stainless steel valves are assembled with PFA-coated front ferrules.➀Height and width of 63 through 68 series flanges. Height of 62 series flange is 1.59 in. (40.4mm); width is J dimension.1060 Series Ball ValvesFemale Pipe Thread End ConnectionsFemale NPT pipe thread dimensions conform to ASME B1.20.1. ISO tapered thread dimensions conform to ISO 7/1, EN 10226-1, DIN-2999, and JIS B0203. See Ordering Information,page 8.➀Height and width of 63 through 68 series flanges. Height of 62 series flange is 1.59 in. (40.4mm); width is J dimension.Steam Trap Test AssemblyDesigned for use with saturated steamsystems, the Swagelok TVA seriesintegrated test valve assembly consists of two 63 series ball valves and a universal mount for use with acustomer-supplied steam trap. The test assembly offers fast visual monitoring of condensate removal with a simple quarter turn of the test valve.Tube and Pipe Socket Weld End ConnectionsPipe socket diameter and depth conform to ASME B16.11. See Ordering Information,page 8.➀Height and width of 63 through 68 series flanges. Height of 62 series flange is 1.59 in. (40.4mm); width is J dimension.Swagelok Welding SystemsThe Swagelok welding system offersconsistent, repeatable orbital gastungsten arc welds (GTAW). It can be used to weld a variety of weld end connections available on Swagelok 60 series ball valves.Pipe Butt Weld End ConnectionsPipe butt weld end connections conform to ASME B16.25. See Ordering Information,page8.➀Height and width of 63 through 68 series flanges. Height of 62 series flange is 1.59 in. (40.4mm); width is J dimension.Tube Extension End ConnectionsTube extensions are available on stainless steel valves only. Tube extension material is 316L SS. See Ordering Information,page 8.➀Height and width of 63 through 68 series flanges. Height of 62 series flange is 1.59 in. (40.4mm); width is J dimension.VCO O-ring Face Seal and VCR Metal Gasket Face Seal Fitting End ConnectionsFace seal fitting end connections require minimal axial clearance for ease of installation and service.VCO fitting contains fluorocarbon FKM O-ring. See Ordering Information,page 8.VCO Fitting Pressure ratings of valves with VCR or VCO fitting end connections are based on the ratings of the mating fitting; see the Swagelok VCR Metal Gasket Face SealFittings or Swagelok VCO O-ring Face Seal Fittings catalogs, MS-01-24 and MS-01-28.➀Height and width of 63 series flange. Height of 62 series flange is 1.59 in. (40.4mm); width is J dimension.VCR FittingSanitary Fitting End ConnectionsValves with Swagelok TS and SC sanitary fitting end connections are available inmaterial and clamp used.a surface finish roughness average (R a )of 15 µin. (0.38µm). For more information, see the SwagelokBiopharm Fittings—TS Series catalog,MS-03-13.SC sanitary clamp end connections are ISO 2852 compatible.See Ordering Information,page 8.➀Height and width of 63 through 68 series flanges. Height of 62 series flange is 1.59 in. (40.4mm); width is J dimension.Mixed End Connections60 series valves can be ordered with two different end connections. Contact your authorized Swagelok representative for ordering information.TS Sanitary FittingsSC Sanitary Clamp Fittings➀Height and width of 63 through 68 series flanges. Height of 62 series flange is 1.59 in. (40.4mm); width is J dimension.Special-Application ValvesSteam Service (S60P Series)Steam service ball valves can reduce lost energy, downtime,and safety hazards associated with leaking valves in a steam system. Unlike conventional sealing methods, the patented designs of the seats and stem packing in the steam series ball valves resist the erosive nature of steam, thus improving performance and enhancing safety.Featuress Stainless steel or carbon steel materials.s PEEK (polyetheretherketone) seats and stem seals s resist absorption of waters resist erosive damage of steam.Grafoil flange seals maintain leaktight integrity at high temperaturesEncased 8-bolt constructionresists differential thermal expansionof body components during rapid temperature cyclingOrdering InformationTo order, insert S before the series designator and replace T with P.Example: SS-S 62P S4To order steel valve body material, replace SS with S.Example: S -S62PS4Wetted components listed in italics.All other components same as shown on page 4.➀S62P and S65P series —impregnated with hydrocarbon-based lubricant.➁S62P and S65P series —RTV silicone sealant.➂S63P series —contains no 316 SS.Materials of ConstructionPressure-Temperature RatingsSeal KitsSeal kits contain instructions and components of the materials listed in Materials of Construction.Kits contain stem springs, gland,packing support, packings, stem bearing, seats, seat springs, back sheets, flange seals, lubricant, and sealant.Select a kit ordering number.Saturated Steam RatingsStainless Steel Valves1050 psig at 550°F (72.3 bar at 287°C)Carbon Steel Valves680 psig at 500°F (46.8 bar at 260°C)Steel valves with Swagelok tube fitting end connections: 375°F (190°C) max.Thermal Service (T60M Series)The Swagelok thermal service ball valve, with its unique,spring-like metal seat, is designed to maintain a seal with a minimum seat load against the ball.Featuress 316 SS or carbon steel material with Grafoil packingand alloy X-750 seatss Resists contamination of the thermal liquid.s Enhances safety in thermal liquid systems.s Meets or exceeds FCI 70-2 Class VI for leaktight shutoff.s Exceeds performance requirements of Fire Test Standard API 607, 4th edition.Wetted components listed in italics.All other components same as shown on page 4.➀Coated with molybdenum disulfide with hydrocarbon binder.➁Impregnated with fluorocarbon-based lubricant.➂Impregnated with anaerobic adhesive. T63M and T65M series —RTV silicone sealant.Ordering InformationThermal series ball valves are available in 63, 65, 67, and 68series sizes. To order, insert T before the series designator and replace the second T with M.Example: SS-T 63M S8To order steel valve body material, replace SS with S.Example: S -T63MS8Smooth,quarter-turn rotary operation s resists outside contaminants s provides reliable containment of thermal liquidsUnique,spring-loaded metal seatss provide positive leaktightsealing at temperatures up to 850°F (454°C)s work equally well in low-and high-pressure systems.Materials of ConstructionEncased 8-bolt constructionresists differential thermal expansion of bodycomponents during rapid temperature cyclingSeal KitsSeal kits contain instructions and components of the materials listed in Materials of Construction.Kits contain ball, seats, packing, flange seals, stem bearings,back seats, packing supports, stem springs, lubricant, and sealant.Select a kit ordering number.Pressure-Temperature RatingsSteel valve ratings limited to –20°F (–28°C).Steel valves with Swagelok tube fitting end connections: 375°F (190°C) max.TestingAll thermal service ball valves are tested with pure nitrogen at 50 psig (3.4 bar) for leaktight integrity of the ball seats as specified by FCI 70-2 Class VI.Stem packing and body seals are tested for no visible leakage using a liquid leakGrafoil weir ringprovides seatseal against theball during fireconditions,even if only aportion of the seat isdestroyedLive-loaded Grafoilstem packingprovides a reliablestem seal duringnormal conditions andmaintains a seal in theevent of fireHigh-strength metalstem bearingsprovide smoothactuation, resist wearand extrusion, andmaintain packing loadin the event of fireGrafoil flange sealsprovide leaktight containment undernormal and fire conditions, eliminatingthe need for a secondary flange sealVented ballallows pressure to equalize between valve bodyand upstream port, preventing overpressurizationand potential seal blowout under fire conditionsEncased 8-bolt constructionmaintains body integrity and bodyseals during rapid temperaturechanges resulting from fire exposureand water quenchingCompensatingseat designlive loads the seat tocompensate for wear andchanges in temperatureor pressure during normalconditions and reducesdistortion of seats frompressure surgesFire Series (A60T Series)Fire series ball valves meet fire test specification API Standard 607, 4th edition.Materials of ConstructionOrdering InformationFire series ball valves are available in 63, 65, 67, and 68series sizes. To order, insert A in the ordering number.Example: SS-A63T S8To order steel valve body material, replace SS with S.Example: S-A63TS8TestingIn addition to the requirements given in Testing,page 5, fireseries ball valves meet those of API Standard 607, 4th edition,and Swagelok WS-166 Fire Test Specification. See theSwagelok Fire Series Ball Valves—A60T Series catalog,MS-02-47, for more details.Wetted components listed in italics.All other components same as shown on page 4.➀RTV silicone sealant on flange seals.Pressure-Temperature RatingsSteel valve ratings limited to –20°F (–28°C).Steel valves with Swagelok tube fitting end connections: 375°F (190°F) max.Seal KitsKits contain stem springs, gland,packing, packing supports, stembearings, seats with integral weirrings, seat springs, and flangeseals.Chlorine Series (C60V Series)Featuress Materials include carbon steel valve body with virgin PTFE seats and packing, in accordance with the guidelines of the Chlorine Institute Pamphlet 6, Piping Systems for Dry Chlorine.s Upstream ball vent prevents overpressurization in ball and body when valve is closed.Pressure-Temperature Ratings300 psig at –20 to 250°F (20.6 bar at –28 to 121°C).Cleaning and PackagingC60V series valve bodies and flanges are cleaned in mineral spirits followed by an aqueous cleaning solution containing a surfactant. All other wetted components are cleaned in accordance with Special Cleaning and Packaging (SC-11).C60V series ball valves are capped and sealed individually in desiccant packaging and are tagged for chlorine service.TestingEvery chlorine series valve is factory tested with nitrogen at 300psig (20.6 bar). Seats have a maximum allowable leak rate of 0.04 std cm 3/min.Shell testing with gas at 300 psig (20.6bar) is performed on 62, 63, and 65 chlorine series valves.Shell testing with gas at 1.5 times the maximum working pressure is performed on 67 and 68 chlorine series valves.Ordering InformationSelect an ordering number from the Dimensions tables for Swagelok tube fitting, female NPT, or tube and pipe socketMaterials of ConstructionAll-Welded Valves (W60T Series)FeaturesAll-welded ball valves incorporate the proven design features of the on-off (2-way)ball valve, all-welded body construction, and live-loaded packing to ensure total system fluid containment.TestingIn addition to the requirements given in Testing,page 5, a hydrostatic shell test is performed with pure water at 1.5times the working pressure.Dimensions and Ordering InformationDimensions in inches and (millimeters) are for reference only, subject to change.Select an ordering number.To order other seat materials, replace T C for carbon/glass PTFE, E for UHMWPE,or V for virgin PTFE.Example: SS-W63C F8Full penetration weld provides one-piece body construction for leaktight fluid containmentSeal KitsKits contain instructions, stem springs, gland, packing support,packings, stem bearing, seatsubassemblies, flange seals, and lubricant.Select a kit ordering number.Wetted components listed in italics.All other components same as shown on page 4.weld end connections. Insert C before the series designator.Replace SS and T with S and V,respectively.Example: S -C 62V S4Featuress Temperature rating –65 to 250°F(–53to 121°C).s Available in 2-way and 3-way 62, 63,and 65 series sizes in stainless steel and in 2-way 62, 63, and 65 series sizes in brass.s Available with seat materials shownin the table below.Ordering InformationT o order, insert L in the ordering number.Examples: SS-L 62TS4SS-L 62XTS4Seal KitsSeal kits contain instructions and components of the materials listed in Materials of Construction.See Seal Kits,page 21.Materials of ConstructionPressure-Temperature RatingsWetted components listed in italics.All other components same as shown on page 4.Wetted components listed in italics.All other components same as shown on page 4.➀Coated with molybdenum disulfide with hydrocarbon binder.Materials of ConstructionOrdering InformationTo order, insert R before the seriesdesignator in the valve ordering number.Example: SS-R 63TS8Pressure-Temperature RatingsSeal KitsSeal kits contain instructions and components of the materials listed in Materials of Construction.Kits contain stem spring, quad seal supports, spacer ring, stem quad seal,stem bearing, seats, seat springs,flange seals, and lubricant.Select a kit ordering number.See Pressure-Temperature Ratings,page 6, for ratings from 100 to 250°F (37 to 121°C).Valves for Low-Temperature Service (L60 Series)Valves for Rapid-Cycle Service (R60T Series)The quad seal-packed ball valve may be moreeffective in applications requiring rapid cycling of a valve or when packing adjustments may be difficult.Vented Valvess Allows vertical or horizontalmounting.s Can be installed on panelsup to 3/16 in. (4.8 mm) for 62 series and 1/4 in.(6.4mm) thick for 63, 65,67, and 68 series.s Fits oval and lever handle.s Provides template for drillingholes.Ordering InformationSelect an ordering number.For 4-Bolt Valves Assembled with Carbon Steel or Stainless Steel Bolts Kit includes self-cinching nut,cover plate, cap screws,panel mount brackets, two stainless and two carbon steel bolts, and instructions.Options and AccessoriesHandlesPanel Mount KitLow Dead Space Inserts s Reduce fluid entrapment around the ball, stem, and seatswhile the valve is in the open or closed position.s For use in select ball valves; not for use on steam, thermal,or fire series valves.s Made from carbon/glass reinforced PTFE.To order, add -LD to the valve ordering number.Examples: SS-62TS4-LD;SS-62XTS4-F8-LDKits for Field AssemblyFor 4-Bolt Valves Assembled with Stainless Steel Studs and All 8-Bolt Valves Kit includes self-cinching nut,cover plate, cap screws, panel mount brackets, and instructions.Vent PassageVent PassageExternal Vent OptionInternal Vent OptionLocking Lever Bracket Handle Oval HandleA variety of handle options is available for use with 60 series ball valves. To order a locking lever bracket handle, add -JL to the ordering number. To order an oval handle, add -JK to the ordering number. For additional information and dimensions,see the Swagelok Process Ball Valves Handle Options catalog,MS-01-137.On-off (2-way) ball valves are available with either an internal or an external vent. These vents are available for either upstream or downstream service. For details and ordering information, see the Swagelok Process Ball Valve Vent Options catalog, MS-02-28.。
世伟洛克FKB系列耳轴型中压球阀说明书
中压球阀FKB 系列世伟洛克 FKB 系列耳轴型球阀采用紧凑型设计，具有扭矩 低、四分之一圈操作的特点，能够在压力最高达 15,000 psig (1034 bar) 的应用场合提供可靠关断。
其它特点还有：■ 流量系数 (C v ) 为 0.44 到 11.3■ 可测的世伟洛克中压卡套管接头和内螺纹 NPT 端接 ■ 2 通（通-断）和 3 通（切换）流动方式■ 经检测的氮气阀座和经检测的外壳可确保产品完整性■ 位置可调的条形手柄和符合 ISO 5211 标准的气动执行机构■ 可选择手动阀面板和肩式安装。
压力—温度额定值欲了解关于带中压卡套管接头端接阀门压力额定值的更多信息，请参考世伟洛克产品目录中压可检测卡套管接头和转换接头，MS-02-335。
有关世伟洛克球阀的重要说明世伟洛克球阀设计用于全开或全闭位置。
在一段时间内未使用的阀门可能会有较高的初始启动力矩。
世伟洛克® 中压卡套管接头 端接：■ 减少阀门安装时间和费用■ 提供牢固的卡套管抓紧和 抗振动性能。
带有独特止动盘的位置可调 手柄：■ 提供元件布局灵活性，能够 减小系统占用的空间。
底部负载阀杆设计：■ 消除了阀杆冲出，提高了操作员安全性。
创新的阀杆密封设计 （正在申请专利）：■ 在整个工作温度范围内保持全压力额定值耳轴球阀采用创新的直接负载设计：■ 能够在很宽压力范围内（即使在系 统卸压和重新加压条件下）保持一 致的密封■ 确保改善的控制系统执行的可靠 操作。
2 FKB 系列中压球阀结构材料4171015161819202124262930235961113121481722252327282-Way3-WayFKB 系列中压球阀 3测试每一个世伟洛克中压球阀生产厂中都使用氮气在 1000 psig(68.9 bar) 压力下进行测试。
阀座的最大容许泄漏率为0.1 std cm 3/分钟。
壳体测试是使用检漏液进行的，达到未检测到泄漏的要求。
swagelock大流量手动气体调压阀
工艺
P =世伟洛克 超高纯工艺规范 (SC‑01); 电抛光, Ra 平均 5 µin. (0.13 µm)
P1 =世伟洛克 特殊清洁与包装 (SC-11); 电抛光, Ra 平均 5 µin. (0.13 µm)
弹簧成套件
弹簧成套件包括加载弹簧、加载盘、标 签和安装说明书。订购时，按照要求的 调压阀出口压力范围选择弹簧成套件 订购型号。
窄型手柄
■ 当系统元件与工艺管线之间空间很小时，用此手柄更容易进 行压力调节
■ 指尖抓紧及外表面滚花设计保证可靠操作。
1.125 in. 模块化表面安装型
■ 用于 1.125 in. C 形和 W 形密封集成气体系统 ■ 流量达 160 std L/min ■ 提供两种压力范围的产品：真空至 30 psig (2.0 bar)
SS – HFM3B – VCR4 – P
阀体材料 316L VIM-VAR 不锈钢
型号 HFM3B = 直线型
MSM-HFM3B = 模块化表面安装
端接 VCR4 = 1/4 in. VCR 短接管➀
VCR4L = 1/4 in. VCR 长接管➀ BW4 = 1/4 in. 卡套管对焊 无 = C 密封表面安装(仅 MSM-HFM3B)
0.40
40..040
0.40 4.0
0.35
30..535
0.35 3.5
尺寸
尺寸以 in. (mm) 为单位表示，仅供参考，可能有变动。
直线型
低扭矩手柄
标准手柄
2.00 (50.8) 直径
1.48 (37.6) 直径
4.12 (105) 最大
4.17 (106) 最大
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
62 系列—316 SS / A276； 63, 65 系列—黄铜 CDA 360 / B16
17 支承环 (2) 18 阀座 (2)
316 SS / A240, A276, 或 A479 加强型 PTFE ➃
19 锥形碟片弹簧 (2) 20 法兰密封 (2) 21 法兰 (2) 22 阀体紧固件 (4) 23 阀体六角螺母 (8 或 4)
其他阀座材料
阀门的阀座是...
还含有...
以及这些润滑剂
合金 X-750➀
S17400 SS 阀球➀ 和 316 SS 后阀座
硅脂基、氟化的二流化钨基 和 PTFE 基
碳 / 玻璃 PTFE PEEK➀➁
与带有 PTFE 阀座的阀相同
PEEK 阀杆支撑➀ 和填料➀
PTFE 基
UHMWPE
UHMWPE 填料， PEEK 阀杆支撑➀ 乙烯丙烯 O 形圈，
60 系列球阀
压力—温度额定值
压力-温度额定值是基于标准结构材料的，如同 4 上和以下表的 附注中所列出的那样。具有替代的结构材料的阀其额定值可能 不与所示出的相符。
对于带 CE 标记的 67 和 68 系列不锈钢 阀门，以 1.5 倍最大工作压力进行壳体 测试。
特殊用途阀
按特殊用途阀一节中所述，某些阀可能有 不同测试要求。
清洁和包装
每个 60 系列球阀均是按照世伟洛克标准 清洁和包装规格 (SC-10), MS-06-62 来 进行处理的。同样也可按照特殊清洁和包 装 (SC‑11), MS‑06‑63 来进行处理，以保 证满足 ASTM G93 等级 C 中所列出的产 品清洁度要求。详情请向您当地授权的世 伟洛克销售服务代表联系。
流体
在高压情况下，阀球被迫向下游，使下游阀座挠曲并产生密封。 上游阀座也随阀球运动而挠曲并保持密封。
流体
切换 (3 通) 阀
所有不锈钢切换球阀都具有通-断 (2 通) 球阀设计的许多特点。整块式中心阀体不使用焊接， 并能作 180°动作，这种切换设计使用户能： ■ 将流体从一个公共入口转移至两个出口之一 ■ 将流体在一个入口上阻塞并泄放反向端口
316L SS / A479 或 CF3M / A351 316 SS gr B8M cl 2 / A193 316 SS gr 8M str hd / A194
应变硬化 316 SS / A167 或 A240
碳氟 FKM ➆
WCB ➄ / A216
黄铜 CDA 360 / B16
镀镉碳钢等级 8 / SAE J429➇
球阀
通用和特殊用途
60 系列
■ 1/8 至 2 in. 和 6 至 25 mm 口径 ■ 不锈钢、碳钢和黄铜和特种合金材料 ■ 通-断 (2 通) 阀和切换 (3 通) 阀 ■ 补偿阀座设计 ■ 活动负载的、两件式阀杆填料
60 系列球阀
目录
有关世伟洛克工艺球阀 的重要信息................................................................... 2 结构材料....................................................................... 4 测试.............................................................................. 5 清洁与包装................................................................... 5 压力-温度额定值.......................................................... 6 订购信息....................................................................... 8 尺寸 世伟洛克 (Swagelok®) 管接头端接........................... 9 内螺纹端接................................................................ 10 卡套管和公称管承插焊连接....................................... 11 公称管对焊连接......................................................... 12 卡套管接长端接......................................................... 13 VCO® 和 VCR® 面密封接头端接............................... 13 卫生设备管接头端接.................................................. 14 混合端接.................................................................... 14 专用阀 耐蒸气阀.................................................................... 15 耐热阀....................................................................... 16 耐火阀....................................................................... 17 耐氯气阀.................................................................... 18 全焊接阀.................................................................... 19 低温阀....................................................................... 20 快速循环用................................................................ 21 选购件和附件................................................................. 22 气动执行机构................................................................. 24 符合 ISO 5211 标准的气动执行机构............................. 28 用于气动执行机构的选购件........................................... 31 电动执行机构................................................................. 31
镀镉碳钢等级 8 / SAE J995➈
润滑剂
硅脂基和 PTFE 基润滑剂；可提供其他的润滑剂
润湿元件用斜体表示。 ➀ 可供应的特种合金材料包括合金 400、合金 C-276、合金 20、合金 600 和钛。请联系您当地授权的世伟洛克销售和服务代表。 ➁ 62 系列—没有与手柄结合在一起的上阀杆弹簧和止动板。 ➂ 装有气动执行器的阀带有一锁定片（未示出）以将螺母固定在阀杆上。 ➃ 其他可供应的材料；见下文的其他阀体材料。 ➄ 涂有碳氢防锈剂。 ➅ 涂有含碳氢粘合剂的二硫化钼。合金 X-750—2 个支撑；PEEK—1 个支撑。 ➆ 其他可供应的材料；见成套密封法兰，P8。 ➇ 62 系列—材料规格是 ASTM A574。 ➈ 62 系列—螺母是等级 4130 或 4140/ASTM A322 或 A331。
接地弹簧 使阀杆接地提供持续的防静电
活负载、两件式 V 形阀杆填料 ■ 所 需的操作扭矩较小 ■ 能 改善性能 ■ 补 偿阀杆磨损
高强度阀杆支撑 ■ 能 获得平稳的启动 ■ 消 除阀杆和阀体之间的摩擦 ■ 耐磨损
底部加载阀杆 ■ 防止阀杆冲出 ■ 加 强系统安全性
60 系列球阀 挠性阀座设计保证了在低压和高压系统中都具有无泄漏的密封 在低压情况下，密封由锥形碟片弹簧加载阀座推向阀球而获得。 不需要由压力来产生密封。
316 SS
302 SS / A313 低合金钢等级 7 / A194
8 阀杆弹簧 (2)
应变硬化 316 SS / A240
9 密封压盖
涂 PTFE 316 SS / B783
黄铜 CDA 360 / B16
10 填料支承
聚醚醚酮 (PEEK)
11 上填料 12 下填料 13 阀体 14 阀杆支撑➅
对于带 CE 标记的 67 和 68 系列阀门， 以 1.5 倍最大工作压力进行壳体测试。
金属阀座阀和 3 通 PEEK 阀座阀
按 FCI 70-2 规格等级 VI 的规定，每个 60 系列球阀在出厂前用氮气在 50 psig (3.4 bar) 压力下进行测试以检查其阀座 防漏完好性。
用氮气在 1000 psig (69 bar)- 若最高额定 压力低于 1000 psig (69 bar)，则使用最高 额定压力-下进行壳体测试，达到使用检漏 液检测不到泄漏的要求。
60 系列球阀
结构材料
阀体材料➀
不锈钢
碳钢
黄铜
元件 1 阀杆螺母 2 阀杆弹簧➁ 3 止动板➁ 4 手柄
316 SS
材料等级 / ASTM 规范 低合金钢等级 7 / A194
应变硬化 316 SS / A240
304 SS / A240 或 316 SS / A240