齿轮参数中英文对照
proe齿轮参数中英对照
proe齿轮参数中英对照2010-07-11 07:41英文齿轮参数中文齿轮参数number of teeth 齿数normal module 法向模数transverse module 端面模数addendum modification factor 变位系数reference diameter 分度圆直径tip diameter 齿顶圆直径root diameter 齿根圆直径base diameter 基圆直径prefinishing diameter 剃前渐开线起始圆直径control form diameter 渐开线检查有效直径effective outside diameter 渐开线终止圆直径lead 导程normal pressure angle 法向压力角transverse pressure angle 端面压力角helix angle 分度圆螺旋角base helix angle 基圆螺旋角hand of helix 旋向circular thickness on Dp 分度圆上弧齿厚chordal addendum 弦齿高normal circular thickness on Dp after finishing and heat treatment 分度圆弦齿厚base tangent measurement after finishing and heat treatment 公法线长度dimension over f diameter balls or pin after finishing and heat treament 跨棒距backlash 总侧系center distance 中心距tool tip radius 刀具齿顶圆角半径tooth tip fillet angle refered to axis 齿顶倒角number of teeth of mating gear 配对齿轮齿数Toothed gear；Gear 齿轮Gear pair 齿轮副Gear pair with parallel axes 平行轴齿轮副Gear pair with intersecting axes 相交轴齿轮副Train of gears 齿轮系Planetary gear train 行星齿轮系Gear drive；Gear transmission 齿轮传动Mating gears 配对齿轮Pinion 小齿轮Wheel；Gear 大齿轮Driving gear 主动齿轮Driven gear 从动齿轮Planet gear 行星齿轮Planet carrier 行星架Sun gear 太阳轮Ring gear；Annulus gear 内齿圈External gear 外齿轮Internal gear 内齿轮Centre distance 中心距Shaft angle 轴交角Line of centres 连心线Speed reducing gear pair 减速齿轮副Speed increasing gear pair 增速齿轮副Gear ratio 齿数比Transmission ratio 传动比Axial plane 轴平面Datum plane 基准平面Pitch plane 节平面Transverse plane 端平面Normal plane 法平面Reference surface 分度曲面Pitch surface 节曲面Tip surface 齿顶曲面Root surface 齿根曲面Basic tooth profile 基本齿廓Basic rack 基本齿条Counterpart rack 产形齿条Generating gear of a gear 产形齿轮Generating flank 产形齿面Tooth space 齿槽Right-hand teeth 右旋齿Left-hand teeth 左旋齿Gears with addendum modification；变位齿轮Addendum modification factor 变位系数X-gearsX-gear pair with reference centre distance 高度变位圆柱齿轮副X-gear pair with modified centre distance 角度变位圆柱齿轮副X-gear pair without shaft angle modification 高度变位锥齿轮副X-gear pair with shaft angle modification 角度变位圆柱齿轮副Modification coefficient 变位系数Addendum modification 变位量Addendum modification coefficient 径向变位系数Centre distance modification coefficient 中心距变位系数Cylindrical gear 圆柱齿轮Tip circle 顶圆Root circle 根圆Pitch 齿距Angular pitch 齿距角Base tangent length 公法线长度Reference diameter 分度圆直径Pitch diameter 节圆直径Fillet radius 齿根圆角半径Tooth depth 齿高Working depth 工作高度Addendum 齿顶高Dedendum 齿根高Chordal height 弦齿高Constant chord height 固定弦齿高Facewidth 齿宽Effective facewidth 有效齿宽Transverse tooth thickness 端面齿厚Normal tooth thickness 法向齿厚Transverse base thickness 端面基圆齿厚Normal base thickness 法向基圆齿厚Transverse chordal tooth thickness 端面弦齿厚Constant chord 固定弦齿厚Crest width 端面齿顶厚Normal crest width 法向齿顶厚Transverse spacewidth 端面齿槽宽Normal spacewidth 法向齿槽宽Tooth thickness half angle 齿厚半角Spacewidth half angle 槽宽半角Nominal pressure angle 齿形角Arc-contact worm；hollow flank worm；ZC-worm 圆弧圆柱蜗杆Enveloping worm with straight line grneratrix；TA worm 直廓环面蜗杆Planar worm wheel；P-worm wheel 平面蜗杆Planar double enveloping worm；TP-worm 平面包络环面蜗杆Planar double-enveloping worm wheel；TP-worm wheel 平面二次包络蜗杆Toroid enveloping worm wheel；TK-worm wheel 锥面包络环面蜗杆Toroid enveloping worm hich involute holicoid generatrix；TI-worm 渐开线包络环面蜗杆Spiroid 锥蜗杆Spiroid gear 锥蜗轮Spiroid gear pair 锥蜗杆副Mid-plane 中平面Prolate hypocycloid 长幅内摆线Curtate hypocycloid 短幅内摆线Involute；渐开线Involute to a circleProlate involute 延伸渐开线Curtate involute 缩短渐开线Spherical involute 球面渐开线Involute helicoid 渐开螺旋面Screw helicoid 阿基米德螺旋面Spherical involute helicoid 球面渐开螺旋面Toroid 圆环面Generant of the toroit 圆环面的母圈Middle circle of the toroid 圆环面的中性圈Middle-plane of the toroid 圆环面的中间平面Inner circle of the toroid 圆环面的内圈Meshing interference 啮合干涉Cutter interference 切齿干涉Profile modification；齿廓修型Profile correctionTip relief 修缘Root relief 修根Axial modification；齿向修形Longitudinal correctionEnd relief 齿端修薄Crowning 鼓形修整Crowned teeth 鼓形齿Undercut 挖根Instantaneous axis 瞬时轴Point of contact 瞬时接触点Line of contact 瞬时接触线Transverse path of contact 端面啮合线Surface of action 啮合曲面Plane of action 啮合平面Zone of action 啮合区域Total arc of transmission 总作用弧Transverse arc of transmission 端面作用弧Overlap arc 纵向作用弧Total angle of transmission 总作用角Transverse angle of transmission 端面作用角Overlap angle 纵向作用角Total contact ratio 总重合度Transverse ratio 端面重合度Overlap ratio 纵向重合度Standard gears 标准齿轮X-gero gear 非变位齿轮Referencr centre distance 标准中心距Nominal centre distance 名义中心距Reference cylinder 分度圆柱面Pitch cylinder 节圆柱面Basic cylinder 基圆柱面Tip cylinder 齿顶圆柱面Root cylinder 齿根圆柱面Pitch point 节点Pitch line 节线Reference circle 分度圆Pitch circle 节圆Basic circle 基圆Locating face 定位面Outer cone distance 外锥距Inner cone distance 内锥距Mean cone distance 中点锥距Back cone distance 背锥距Locating distance 安装距Tip distance；crown to back 轮冠距Apex to crown 冠顶距Offset 偏置距Offset of tooth trace 齿线偏移量Reference cone angle 分锥角Pitch cone angle 节锥角Tip angle 顶锥角Root angle 根锥角Back cone angle 背锥角Addendum angel 齿顶角Dedendum angle 齿根角Pressure angle at a point 任意点压力角Spiral angle at a point 任意点螺旋角Mean spiral angle 中点螺旋角Outer spiral angle 大端螺旋角Inner spiral angle 小端螺旋角Worm 蜗杆Worm wheel 蜗轮Worm gear pair 蜗杆副Cylindrical worm 圆柱蜗杆Cylindrical worm pair 圆柱蜗杆副Enveloping worm 环面蜗杆Enveloping worm pair 环面蜗杆副Straight sided axial worm；ZA-worm 阿基米德蜗杆Involute helicoid worm；ZI-worm 渐开线蜗杆Straight sided normal worm；ZN-worm 法向直廓蜗杆Milled helicoid worm；ZK-worm 锥面包络圆柱蜗杆Elliptical gear 椭圆齿轮Non-circular gear pair 非圆齿轮副Cylindsical lantern pinion and wheel 圆柱针轮副Cylindsical tan tein gear ；pin-wheel 针轮Harmoric gear drive 谐波齿轮副Wave generator 波发生器Flexspine 柔性齿轮Circular spline 刚性齿轮Non-circular gear 非圆齿轮Reference tosoid 分度圆环面。
齿轮参数中英文对照
齿轮参数中英文对照Gear Parameters 齿轮参数1. Pitch Circle Diameter (PCD) 中心圆直径2. Module 压力角Module refers to the ratio of the pitch circle diameter to the number of teeth. It determines the size of the gear teeth and is expressed in millimeters. The module is an essential parameter for gear manufacturing and design.3. Pressure Angle 压力角The pressure angle is the angle between the line of action and a line tangent to the pitch circle. It affects the gear's performance, including its load-carrying capacity and efficiency.4. Number of Teeth 齿数The number of teeth is the total count of teeth on a gear.It plays a crucial role in determining the gear's size,rotational speed, and torque ratio.5. Circular Pitch 圆距The circular pitch is the distance between corresponding points on adjacent gear teeth. It is usually measured along the pitch circle and is represented in millimeters.6. Face Width 面宽The face width refers to the length of the gear teeth along the axis of rotation. It is an essential parameter for ensuring proper load distribution and tooth strength.7. Helix Angle 螺旋角The helix angle is the angle formed between the helix and a plane perpendicular to the gear axis. It determines thedirection of the helical gear's tooth spiral.8. Module Angle 模仰角The module angle is the angle between the line of action and a line tangent to the helix angle. It is a critical parameterfor helical gears.9. Helix Lead 螺旋铅距10. Backlash 间隙Backlash is the amount of clearance or play between the mating gears when they are not in contact. It affects the transmission accuracy and must be carefully controlled in gear design.11. Addendum 圆顶The addendum is the radial distance between the pitch circle and the outermost point on the gear tooth. It ensures proper engagement between gears.12. Dedendum 圆谷The dedendum is the radial distance between the pitch circle and the innermost point on the gear tooth. It providessufficient space for the mating gear's teeth.13. Dedendum Angle 谷角The dedendum angle is the angle between the dedendum and a radial line from the gear center. It affects the gear'sdurability and strength.14. Working Depth 有效厚度The working depth is the radial distance between the addendum and dedendum. It plays a crucial role in determining the gear's load-carrying capacity and strength.15. Pitch Diameter 齿顶直径The pitch diameter is the diameter of the pitch circle. It is typically used in gear calculations.。
齿轮参数术语中英文对照总结
齿轮参数术语中英文对照总结-标准化文件发布号：（9556-EUATWK-MWUB-WUNN-INNUL-DDQTY-KII齿轮参数中英对照英文齿轮参数中文齿轮参数number of teeth 齿数normal module 法向模数transverse module 端面模数addendum modification factor 变位系数reference diameter 分度圆直径tip diameter 齿顶圆直径root diameter 齿根圆直径base diameter 基圆直径prefinishing diameter 剃前渐开线起始圆直径control form diameter 渐开线检查有效直径effective outside diameter 渐开线终止圆直径lead 导程normal pressure angle 法向压力角transverse pressure angle 端面压力角helix angle 分度圆螺旋角base helix angle 基圆螺旋角hand of helix 旋向circular thickness on Dp 分度圆上弧齿厚chordal addendum 弦齿高normal circular thickness on Dp after finishing and heat treatment 分度圆弦齿厚base tangent measurement after finishing and heat treatment 公法线长度dimension over f diameter balls or pin after finishing and heat treament 跨棒距backlash 总侧系center distance 中心距tool tip radius 刀具齿顶圆角半径tooth tip fillet angle refered to axis 齿顶倒角number of teeth of mating gear 配对齿轮齿数Toothed gear；Gear 齿轮Gear pair 齿轮副Gear pair with parallel axes 平行轴齿轮副Gear pair with intersecting axes 相交轴齿轮副Train of gears 齿轮系Planetary gear train 行星齿轮系Gear drive；Gear transmission 齿轮传动Mating gears 配对齿轮Pinion 小齿轮Wheel；Gear 大齿轮Driving gear 主动齿轮Driven gear 从动齿轮Planet gear 行星齿轮Planet carrier 行星架Sun gear 太阳轮Ring gear；Annulus gear 内齿圈External gear 外齿轮Internal gear 内齿轮Centre distance 中心距Shaft angle 轴交角Line of centres 连心线Speed reducing gear pair 减速齿轮副Speed increasing gear pair 增速齿轮副Gear ratio 齿数比Transmission ratio 传动比Axial plane 轴平面Datum plane 基准平面Pitch plane 节平面Transverse plane 端平面Normal plane 法平面Reference surface 分度曲面Pitch surface 节曲面Tip surface 齿顶曲面Root surface 齿根曲面Basic tooth profile 基本齿廓Basic rack 基本齿条Counterpart rack 产形齿条Generating gear of a gear 产形齿轮Generating flank 产形齿面Right-hand teeth 右旋齿Left-hand teeth 左旋齿Gears with addendum modification；变位齿轮Addendum modification factor 变位系数X-gearsX-gear pair with reference centre distance 高度变位圆柱齿轮副X-gear pair with modified centre distance 角度变位圆柱齿轮副X-gear pair without shaft angle modification 高度变位锥齿轮副X-gear pair with shaft angle modification 角度变位圆柱齿轮副Modification coefficient 变位系数Addendum modification 变位量Addendum modification coefficient 径向变位系数Centre distance modification coefficient 中心距变位系数Cylindrical gear 圆柱齿轮Tip circle 顶圆Root circle 根圆Pitch 齿距Angular pitch 齿距角Base tangent length 公法线长度Reference diameter 分度圆直径Pitch diameter 节圆直径Fillet radius 齿根圆角半径Working depth 工作高度Addendum 齿顶高Dedendum 齿根高Chordal height 弦齿高Constant chord height 固定弦齿高Facewidth 齿宽Effective facewidth 有效齿宽Transverse tooth thickness 端面齿厚Normal tooth thickness 法向齿厚Transverse base thickness 端面基圆齿厚Normal base thickness 法向基圆齿厚Transverse chordal tooth thickness 端面弦齿厚Constant chord 固定弦齿厚Crest width 端面齿顶厚Normal crest width 法向齿顶厚Transverse spacewidth 端面齿槽宽Normal spacewidth 法向齿槽宽Tooth thickness half angle 齿厚半角Spacewidth half angle 槽宽半角Nominal pressure angle 齿形角Arc-contact worm；hollow flank worm；ZC-worm 圆弧圆柱蜗杆Enveloping worm with straight line grneratrix；TA worm 直廓环面蜗杆Planar worm wheel；P-worm wheel 平面蜗杆Planar double enveloping worm；TP-worm 平面包络环面蜗杆Planar double-enveloping worm wheel；TP-worm wheel 平面二次包络蜗杆Toroid enveloping worm wheel；TK-worm wheel 锥面包络环面蜗杆Toroid enveloping worm hich involute holicoid generatrix；TI-worm 渐开线包络环面蜗杆Spiroid 锥蜗杆Spiroid gear 锥蜗轮Spiroid gear pair 锥蜗杆副Mid-plane 中平面Prolate hypocycloid 长幅内摆线Curtate hypocycloid 短幅内摆线Involute；渐开线Involute to a circleProlate involute 延伸渐开线Curtate involute 缩短渐开线Spherical involute 球面渐开线Involute helicoid 渐开螺旋面Screw helicoid 阿基米德螺旋面Spherical involute helicoid 球面渐开螺旋面Toroid 圆环面Generant of the toroit 圆环面的母圈Middle circle of the toroid 圆环面的中性圈Middle-plane of the toroid 圆环面的中间平面Inner circle of the toroid 圆环面的内圈Meshing interference 啮合干涉Cutter interference 切齿干涉Profile modification；齿廓修型Profile correctionTip relief 修缘Root relief 修根Axial modification；齿向修形Longitudinal correctionEnd relief 齿端修薄Crowning 鼓形修整Crowned teeth 鼓形齿Undercut 挖根Instantaneous axis 瞬时轴Point of contact 瞬时接触点Line of contact 瞬时接触线Transverse path of contact 端面啮合线Surface of action 啮合曲面Plane of action 啮合平面Zone of action 啮合区域Total arc of transmission 总作用弧Transverse arc of transmission 端面作用弧Overlap arc 纵向作用弧Total angle of transmission 总作用角Transverse angle of transmission 端面作用角Overlap angle 纵向作用角Total contact ratio 总重合度Transverse ratio 端面重合度Overlap ratio 纵向重合度Standard gears 标准齿轮X-gero gear 非变位齿轮Referencr centre distance 标准中心距Nominal centre distance 名义中心距Reference cylinder 分度圆柱面Pitch cylinder 节圆柱面Basic cylinder 基圆柱面Tip cylinder 齿顶圆柱面Root cylinder 齿根圆柱面Pitch point 节点Pitch line 节线Reference circle 分度圆Pitch circle 节圆Basic circle 基圆Locating face 定位面Outer cone distance 外锥距Inner cone distance 内锥距Mean cone distance 中点锥距Back cone distance 背锥距Locating distance 安装距Tip distance；crown to back 轮冠距Apex to crown 冠顶距Offset 偏置距Offset of tooth trace 齿线偏移量Reference cone angle 分锥角Pitch cone angle 节锥角Tip angle 顶锥角Root angle 根锥角Back cone angle 背锥角Addendum angel 齿顶角Dedendum angle 齿根角Pressure angle at a point 任意点压力角Spiral angle at a point 任意点螺旋角Mean spiral angle 中点螺旋角Outer spiral angle 大端螺旋角Inner spiral angle 小端螺旋角Worm 蜗杆Worm wheel 蜗轮Worm gear pair 蜗杆副Cylindrical worm 圆柱蜗杆Cylindrical worm pair 圆柱蜗杆副Enveloping worm 环面蜗杆Enveloping worm pair 环面蜗杆副Straight sided axial worm；ZA-worm 阿基米德蜗杆Involute helicoid worm；ZI-worm 渐开线蜗杆Straight sided normal worm；ZN-worm 法向直廓蜗杆Milled helicoid worm；ZK-worm 锥面包络圆柱蜗杆Elliptical gear 椭圆齿轮Non-circular gear pair 非圆齿轮副Cylindsical lantern pinion and wheel 圆柱针轮副Cylindsical tan tein gear ；pin-wheel 针轮Harmoric gear drive 谐波齿轮副Wave generator 波发生器Flexspine 柔性齿轮Circular spline 刚性齿轮Non-circular gear 非圆齿轮Reference tosoid 分度圆环面11。
花键齿轮参数中英文对照
花键齿轮参数中英文对照在花键齿轮设计中，有许多参数需要考虑。
下面是一些常见的花键齿轮参数的中英文对照。
1. Pitch Diameter (齿圈中心直径)2. Module (模数)3. Number of teeth (齿数)4. Pressure angle (压力角)5. Face width (齿宽)6. Tooth thickness (齿厚)7. Backlash (啮合间隙)8. Addendum (齿顶高)9. Dedendum (齿根高)10. Circular pitch (齿距)11. Helix angle (螺旋角)12. Pitch line velocity (周速)13. Contact ratio (接触比)14. Tooth profile (齿形)在设计花键齿轮时，这些参数是必不可少的。
以下是对每个参数的详细解释：1. Pitch Diameter (齿圈中心直径): 齿圈的中心直径，用于计算基本的齿轮几何尺寸。
2. Module (模数): 模数是齿轮设计中的一个重要参数，它表示了齿轮齿距和齿轮的尺寸之间的比例关系。
3. Number of teeth (齿数): 齿轮上的齿的数量，它决定了齿轮的大小和传动比。
4. Pressure angle (压力角): 齿轮上齿面的斜率与压力线的夹角。
5. Face width (齿宽): 齿轮上齿面的宽度，在花键齿轮传动中起支撑和传递力的作用。
6. Tooth thickness (齿厚): 齿轮上齿的厚度，决定了花键齿轮的载荷和传力能力。
7. Backlash (啮合间隙): 两个齿轮啮合时，齿的间隙或微小间隔。
8. Addendum (齿顶高): 齿轮齿面的齿高，从基圆到齿顶的距离。
9. Dedendum (齿根高): 齿轮齿面的齿根高度，从基圆到齿根尖的距离。
10. Circular pitch (齿距): 齿轮上齿与相邻齿距离的测量，从齿顶到齿顶的距离。
齿轮参数中英文对照
A.1. abrasive tooth wear 齿面研磨磨损2. absolute tangential velocity 绝对切向速度3. accelerometer 加速表4. addendum 齿顶高5. addendum angle 齿顶角6. addendum circle 齿顶圆7. addendum surface 上齿面8. adhesive wear 粘着磨损9. adjustability 可调性10. adjustability coefficients 可调系数11. adjusting wedge 圆盘端铣刀的可调型楔块12. allowable stress 允许应力13. alternate blade cutter 双面刀盘14. angular backlash 角侧隙15. angular bevel gears 斜交锥齿轮16. angular displacement 角移位17. angular pitch 齿端距18. angular testing machine 可调角度试验机19. approach action 啮入20. arbor 心轴21. arbor distance 心轴距22. arc of approach 啮入弧23. arc of recess 啮出弧24. attraction 收紧25. average cutter diameter 平均刀尖直径26. axial displacement 轴向位移27. axial factor 轴向系数28. axial locating surface 轴向定位面29. axial pitch 轴向齿距30. axial plane 轴向平面31. axial rakeangle 轴向前角32. axial thrust 轴向推力33. axle testing machine 传动桥试验机B.1．back angle 背锥角2．Back angle distance 背角距（在背锥母线方向）3．Back cone 背锥4．Back cone distance 背锥距5．Back cone element 背锥母线6．Backlash 侧隙7．Backlash tolerance 侧隙公差8．Backlash variation 侧隙变量9．Backlash variation tolerance 侧隙变量公差10．Bandwidth 频带宽11．Base circle 基圆12．Base diameter 基圆直径13．Base pitch 基节14．Base radius 基圆半径15．Base spiral angle 基圆螺旋角16．Basic rack 基本齿条17．Bearing 轴承18．Bearing preload 轴承预负荷19．Bearing spacing／spread 轴承间距20．Bending fatigue 弯曲疲劳21．Bending stress 弯曲应力22．Bevel gears 锥齿轮23．Bias 对角接触24．Bias in 内对角接触25．Bias out 外对角接触26．Blade angle 刀齿齿廓角27．Blade edge radius 刀尖圆角半径28．Blade letter 刀尖凸角代号29．Blade life 刀尖寿命30．Blade point width 刀顶宽31．Blank offset 毛坯偏置距32．Bland position 毛坯位置33．Bottom land 齿槽底面34．Boundary lubrication 界面润滑35．Breakage 破裂36．Bridged contact pattern 桥型接触斑点37．Broach 拉刀38．Burnishing 挤齿C．1. Case crushing 齿面塌陷2. CBN 立方氮化硼3. chamfer 倒角4. chordal addendum 弦齿高5. chordal thickness 弦齿厚6. chuck 卡盘7. circular broach 圆拉刀8. circular face-mill 圆盘端面铣刀9. circular peripheral-mill 圆盘铣刀10. circular pitch 周节11. circular thickness 弧齿厚12. circular thickness factor 弧齿厚系数13. clearance 顶隙14. clearance angle 后角15. coarse pitch 大节距16. coast side 不工作齿侧17. combination 组合18. combined preload 综合预负荷19. complementary crown gears 互补冠状齿轮20. completing cycle 全工序循环21. composite action 双面啮合综合检验误差22. compressive stress 压应力23. concave side 凹面24. concentricity 同心度25. concentricity tester 同心度检查仪26. cone distance 锥距27. cone element 锥面母线28. conformal surfaces 共型表面29. coniskoid 斜锥齿轮30. conjugate gears 共轭齿轮31. conjugate racks 共轭齿条32. contact fatigue 接触疲劳33. contact norma 接触点法线34. contact pattern (tooth contact pattern) 轮齿接触斑点35. contact ratio 重合度36. contact stress 接触应力37. continuous index 连续分度38. control gear 标准齿轮，检验用齿轮39. convex side 凸面40. coolant 冷却液41. corrosive wear 腐蚀性磨损42. corrugated tool 阶梯刨刀43. counter forma surfaces 反法向表面44. cradle 摇台45. cradle test roll 摇台角46. cross 大小端接触47. crossing point 交错点48. crown 齿冠49. crown circle 锥齿轮冠圆50. crowned teeth 鼓形齿51. crown gear 冠轮52. crown to back （轮冠距）轮冠至安装定位面距离53. crown to crossing point 轮冠至相错点距离54. cutter 刀盘55. cutter axial 刀盘的轴向位置56. cutter axial plane 刀盘轴向平面57. cutter axis 刀盘轴线58. cutter diameter 刀盘直径59. cutter edge radius 刀刃圆角半径60. cutter head 刀盘体61. cutter number 刀号62. cutter parallel 刀盘平垫片63. cutter point diameter 刀尖直径64. cutter point radius 刀尖半径65. cutter point width 刀顶距66. cutter spindle 刀盘主轴67. cutter spindle rotation angle 刀盘主轴转角68. cutting distance 切齿安装距69. C.V. testing mashing 常速试验机70. cyclex 格里森粗铣精拉法圆盘端铣刀71. cylindrical gears 圆柱齿轮D.1．Datum tooth 基准齿2．Debur 去毛刺3．Decibel (CB) （噪音）分贝4．Decimal ratio 挂轮比值5．Dedendum 齿根高6．Dendendum angle 齿根角7．Dedendum surface 下齿面8．Deflection 挠曲9．Deflection test 挠曲试验10．Deflection testing machine 挠曲试验机11．Depthwise taper 齿高收缩12．Design data sheet 设计数据表13．Destructive pitting 破坏性点蚀14．Destructive wear 破坏性磨损15．Developed setting 试切调整16．Dial indicator 度盘式指示表17．Diametral pitch 径节18．Diamond 菱形接触19．Dinging ball check 钢球敲击检查20．Disc-mill cuter 盘铣刀21．Dish angle 凹角22．Displacement 位移23．Displacement error 位移误差24．Double index 双分度25．Double roll 双向滚动26．Down roll 向下滚动27．Drive side 工作齿侧28．Duplete 双刃刀29．Duplex 双重双面法30．Duplex helical 双重螺旋法（加工方法之一）31．Duplex spread blade 双重双面刀齿（加工／磨齿方法）32．Duplex taper 双重收缩齿33．Durability factor 耐久系数34．Dynamic factor 动载荷系数E。
齿轮参数-中英文对照_GearText_table_translation
fα fβ Hα Hβ i pt i p pk α β
说明 Description 齿廓形状偏差 螺旋线形状偏差 齿廓斜率偏差 螺旋线斜率偏差 一齿切向综合偏差 单个齿距偏差 切向综合总偏差 齿距累计总偏差 齿距累计偏差 齿廓总偏差 螺旋线总偏差 Profile form deviation Helix form deviation Profile slope deviation Helix slope deviation Tooth-to-tooth tangential composite deviation Single pitch deviation Total tangential composite deviation Total cumulative pitch deviation Cumulative pitch deviation Total profile deviation Total helix deviation
法向模数 纵向重合度 一齿径向综合偏差 径向综合总偏差 有效长度 精度等级 齿数 径向跳动
ε
f" F"
L
Q z
F
r
ISO 1328-2
符号 Symbol 12 13 14 15 16 17 18 19 20 说明 Description 分度圆直径
n β i i AE
d m
Reference diameter Normal module Overlap ratio Tooth-to-tooth radial composite deviation Total radial composite deviation Active length Accuracy grade number Number of teeth Run out
花键齿轮参数中英文对照汇总
花键齿轮参数中英文对照汇总1. 模数（Module）：The module is the ratio of the pitch circle diameter to the number of teeth on the gear.2. 齿数（Number of Teeth）：The number of teeth on the gear.3. 压力角（Pressure Angle）：The pressure angle is the angle between the line of action and the line tangent to the pitch circle.4. 分度圆直径（Pitch Circle Diameter）：The pitch circle diameter is the diameter of the hypothetical circle that the gear teeth would be if removed from the gear.5. 脱啮廓角度（Addendum Angle）：The addendum angle is the angle between the tooth profile and the pitch circle.6. 脱啮圆直径（Addendum Circle Diameter）：The addendum circle diameter is the diameter of the imaginary circle that touches the tops of the gear teeth.7. 顶圆直径（Outside Diameter）：The outside diameter is the diameter of the gear measured over the tops of the teeth.8. 底圆直径（Root Diameter）：The root diameter is the diameter of the gear measured at the base of the tooth spaces.9. 压力角圆直径（Base Circle Diameter）：The base circle diameter is the diameter of the imaginary circle that touches the bottoms of the gear teeth.10. 正啮角（Helix Angle）：The helix angle is the angle between the gear tooth and the gear axis in the axial plane.11. 抬齿量（Lift）：The lift is the distance between the pitch circle and the tip of the gear tooth measured along the gear axis.12. 径向节圆直径（Dedendum Circle Diameter）：The dedendum circle diameter is the diameter of the imaginary circle that passes through the bottom of the tooth spaces.13. 中心距（Center Distance）：The center distance is the distance between the centers of two gears.14. 节圆直径（Dedendum Diameter）：The dedendum diameter is the diameter of the imaginary circle that touches the bottoms of the gear teeth.15. 啮合高度（Tooth Contact Height）：The tooth contact height is the height of the gear tooth that is actively meshed.16. 公法线长度（Circular Arc Length）：The circular arc length is the length of the measured arc on the pitch circle.17. 顶高（Addendum）：The addendum is the distance from the pitch circle to the top of the tooth.18. 底高（Dedendum）：The dedendum is the distance from the pitch circle to the bottom of the tooth space.19. 中面宽（Face Width）：The face width is the width of the gear tooth measured parallel to the axis.20. 齿根圆滚压深度（Fillet Depth）：The fillet depth is the depth of the circular arc notch in the root of the gear tooth.以上是关于花键齿轮参数的中英文对照汇总，希望能对您有所帮助。
齿轮参数中英对照
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
齿轮参数中英文对照WORD格式A.1.abrasivetoothwear齿面研磨磨损2.absolutetangentialvelocity绝对切向速度3.accelerometer加速表4.addendum齿顶高5.addendumangle齿顶角6.addendumcircle齿顶圆7.addendumsurface上齿面8.adhesivewear粘着磨损9.adjustability可调性10.adjustabilitycoefficients可调系数11.adjustingwedge圆盘端铣刀的可调型楔块12.allowablestress允许应力13.alternatebladecutter双面刀盘14.angularbacklash角侧隙15.angularbevelgears斜交锥齿轮16.angulardisplacement角移位17.angularpitch齿端距18.angulartestingmachine可调角度试验机19.approachaction啮入20.arbor心轴21.arbordistance心轴距22.arcofapproach啮入弧23.arcofrecess啮出弧24.attraction收紧25.averagecutterdiameter平均刀尖直径26.axialdisplacement轴向位移27.axialfactor轴向系数28.axiallocatingsurface轴向定位面29.axialpitch轴向齿距30.axialplane轴向平面31.axialrakeangle轴向前角32.axialthrust轴向推力33.axletestingmachine传动桥试验机B.1．backangle背锥角2．Backangledistance背角距（在背锥母线方向）3．Backcone 背锥4．Backconedistance背锥距5．Backconeelement背锥母线6．Backlash侧隙7．Backlashtolerance侧隙公差8．Backlashvariation侧隙变量WORD格式9．Backlashvariationtolerance侧隙变量公差10．Bandwidth 频带宽11．Basecircle基圆12．Basediameter基圆直径13．Basepitch基节14．Baseradius基圆半径15．Basespiralangle基圆螺旋角16．Basicrack基本齿条17．Bearing轴承18．Bearingpreload轴承预负荷19．Bearingspacing／spread轴承间距20．Bendingfatigue弯曲疲劳21．Bendingstress弯曲应力22．Bevelgears锥齿轮23．Bias对角接触24．Biasin内对角接触25．Biasout外对角接触26．Bladeangle刀齿齿廓角27．Bladeedgeradius刀尖圆角半径28．Bladeletter刀尖凸角代号29．Bladelife刀尖寿命30．Bladepointwidth刀顶宽31．Blankoffset毛坯偏置距32．Blandposition毛坯位置33．Bottomland齿槽底面34．Boundarylubrication界面润滑35．Breakage破裂36．Bridgedcontactpattern桥型接触斑点37．Broach拉刀38．Burnishing挤齿C．34.Casecrushing齿面塌陷35.CBN立方氮化硼36.chamfer倒角37.chordaladdendum弦齿高38.chordalthickness弦齿厚39.chuck卡盘40.circularbroach圆拉刀41.circularface-mill圆盘端面铣刀42.circularperipheral-mill圆盘铣刀43.circularpitch周节44.circularthickness弧齿厚45.circularthicknessfactor弧齿厚系数WORD格式46.clearance顶隙47.clearanceangle后角48.coarsepitch大节距49.coastside不工作齿侧/doc/e42456300.html,bination组合/doc/e42456300.html,binedpreload综合预负荷/doc/e42456300.html,plementarycro wngears互补冠状齿轮/doc/e42456300.html,pletingcycle全工序循环/doc/e42456300.html,positeaction双面啮合综合检验误差/doc/e42456300.html,pressivestress压应力56.concaveside凹面57.concentricity同心度58.concentricitytester同心度检查仪59.conedistance锥距60.coneelement锥面母线61.conformalsurfaces共型表面62.coniskoid斜锥齿轮63.conjugategears共轭齿轮64.conjugateracks共轭齿条65.contactfatigue接触疲劳66.contactnorma接触点法线67.contactpattern(toothcontactpattern)轮齿接触斑点68.contactratio重合度69.contactstress接触应力70.continuousindex连续分度71.controlgear标准齿轮，检验用齿轮72.convexside凸面73.coolant冷却液74.corrosivewear腐蚀性磨损75.corrugatedtool阶梯刨刀76.counterformasurfaces反法向表面77.cradle摇台78.cradletestroll摇台角79.cross大小端接触80.crossingpoint交错点81.crown齿冠82.crowncircle锥齿轮冠圆83.crownedteeth鼓形齿84.crowngear冠轮85.crowntoback（轮冠距）轮冠至安装定位面距离86.crowntocrossingpoint轮冠至相错点距离87.cutter刀盘88.cutteraxial刀盘的轴向位置89.cutteraxialplane刀盘轴向平面WORD格式90.cutteraxis刀盘轴线91.cutterdiameter刀盘直径92.cutteredgeradius刀刃圆角半径93.cutterhead刀盘体94.cutternumber刀号95.cutterparallel刀盘平垫片96.cutterpointdiameter刀尖直径97.cutterpointradius刀尖半径98.cutterpointwidth刀顶距99.cutterspindle刀盘主轴100.cutterspindlerotationangle刀盘主轴转角101.cuttingdistance切齿安装距102.C.V.testingmashing常速试验机103.cyclex格里森粗铣精拉法圆盘端铣刀104.cylindricalgears圆柱齿轮D.1．Datumtooth基准齿2．Debur去毛刺3．Decibel(CB)（噪音）分贝4．Decimalratio挂轮比值5．Dedendum齿根高6．Dendendumangle齿根角7．Dedendumsurface下齿面8．Deflection挠曲9．Deflectiontest挠曲试验10．Deflectiontestingmachine挠曲试验机11．Depthwisetaper齿高收缩12．Designdatasheet设计数据表13．Destructivepitting破坏性点蚀14．Destructivewear破坏性磨损15．Developedsetting试切调整16．Dialindicator度盘式指示表17．Diametralpitch径节18．Diamond菱形接触19．Dingingballcheck钢球敲击检查20．Disc-millcuter盘铣刀21．Dishangle凹角22．Displacement位移23．Displacementerror位移误差24．Doubleindex双分度25．Doubleroll双向滚动26．Downroll向下滚动27．Driveside工作齿侧28．Duplete双刃刀29．Duplex双重双面法30．Duplexhelical双重螺旋法（加工方法之一）31．Duplexspreadblade双重双面刀齿（加工／磨齿方法）32．Duplextaper双重收缩齿33．Durabilityfactor耐久系数34．Dynamicfactor动载荷系数E。
1．Ease-off修正、失配2．Eccentric偏心3．Eccentricangle偏心角4．Eccentricity偏心度5．Edgeradius刀尖圆角半径6．Effectivebearingspacing轴承有效间距7．Effectivefacewidth有效宽度（有效齿宽）8．Elasticcoefficient弹性系数9．Elasticdeformation弹性变形10．Elasticlimit弹性极限11．Elastohydrodynamiclubrication 弹性液压润滑12．Element母线、要素13．Endmovement轴向移动14．Endrem修内端凸轮、导程凸轮15．Endurancelife耐久寿命16．Endurancelimit耐久极限17．Enginetorque发动机扭矩18．Enveloping包络19．EPlubricant,EP极压润滑剂20．EPGcheck,“EPG”检查21．Equaladdendumteeth等齿顶高齿22．Equicurv等高齿大轮成形法23．Equidep等高齿24．Equiside等边25．Equivalentfearratio当量传动比26．Equivalentnumberofteeth当量齿数27．Equivalentpitchradius当量节圆半径28．Equivalentrack当量齿条29．Expander涨胎30．Expandingarbor可张心轴31．Extremepressurelubricant 极压润滑剂F.1．Faceacvance斜齿轮扭曲量2．Faceangle顶锥角（面锥角）3．Faceangledistance顶锥角距4．Faceapex顶锥顶5．Faceapexbeyondcrossingpoint顶锥顶至相错点距离6．Facecone顶锥7．Faceconeelement齿顶圆锥母线，面锥母线8．Facecontactratio齿长重合度，轴向重合度（圆柱齿轮）9．Faceline齿面与轴面交线10．Facewidth齿宽11．Factorofsafety安全系数12．Fatiguebreakage疲劳破裂13．Fatiguefailure疲劳失效14．Fatiguetest疲劳测试15．Feedcam进给凸轮16．Feedgears进给齿轮17．Fillet齿根圆角18．Filletcurve齿根过渡曲线19．Filletradius齿根圆角半径20．Filmstrength液膜强度21．Filter(electronic)（电子的）滤波器22．Filter(mechanical)（机械的）滤波器23．Finepitch（小模数）细径节24．Finisher精切机床25．Fishtail鱼尾形26．Fixedsetting固定安装法27．Flank下齿面28．Flanking下齿面加工29．Formarc加工齿轮用的曲线齿廓刀具30．Formate成形法31．Former齿廓样板，靠模32．Forming成型，在磨具内挤压成型33．Formtool成形刀34．Fourieranalysis傅里叶分析35．Frequency频率36．Frictionload摩擦负荷37．Frontangle前角38．Frontcone前锥39．Frontcrown前锥齿冠40．Frontcrowntocrossingpoint前锥齿冠至交错点41．Full-depthteeth全齿高齿42．Fundametal基频G.1．Gable山形齿沟底面2．Gear齿轮3．Gearaxialdisplacement齿轮轴向位移4．Gearaxialplane齿轮轴向平面5．Gearaxis齿轮轴线6．Gearcenter齿轮中心7．Gearcombination齿轮组合8．Gearcone大轮锥距9．Gearedindex齿轮系分度10．Gearfinisher成形法齿轮精切机床11．Gearmanufacturingsummary齿轮加工调整卡12．Gearmarkingcompound检查齿轮啮合涂色剂13．Gearmember大轮14．Gearplaner成型刨齿机15．Gearratio齿数比16．Gearrougher齿轮粗切机床17．Gears齿轮组18．Geartipping齿轮倾斜19．Generatedgear展成法齿轮20．Generatingcam展成凸轮21．Generatinggear展成齿轮22．Generatingpressureangle 产形轮压力角23．Generatingtrain展成传动键24．Generation展成25．Generator展成齿轮加工机床26．Genevaindex星形轮分度，槽轮分度27．Geometryfactor-durability齿面接触强度几何系数28．Geometryfactor0-strength强度几何系数29．G-flow格里森制金属件的商标，采用冷挤压成形法30．G-form采用热锻成形法制造31．GLE-sine砂轮内外压力角正弦波进行修整用机构32．G-plete全工序法33．Gradeability托曳力34．Grindingcracks磨削裂纹35．G-spin精密主轴的机床36．G-trac圆柱齿轮的无端链式机床的商标H．1．Handofcutter刀盘方向2．Handofspiral螺旋方向3．Hand-rollingtester手动滚动试验机4．Hardac镶篇淬硬刀体精切刀盘5．Hardfinishing硬齿面精加工6．Hardnessratiofactor硬度比系数7．Harmonic谐振8．Harmonicsearch谐振追踪9．Harmonicsweep谐振扫描10．Heel轮齿大端11．Heelpattern大端接触12．Helicalduplex双重螺旋法13．Helicalmotion螺旋运动14．Helixact螺旋运动法15．Helixform螺旋成形法16．Hertz(Hz)赫兹17．Hookangle断面前角18．Horizontaldisplacement水平位移19．Horizontaloffset水平偏置20．HRH高减速比准双曲面齿轮（大于10：1的减速比）21．Huntingtoothcombination大小齿轮齿数无公因数的齿轮副22．Hudrodynamiclubrication液压润滑23．Hupermesh超配合24．Hypoidgears准双曲面齿轮25．Hypoidoffset准双曲面齿轮偏置距I.1．Imaginarygeneratinggear假想成形法2．Incrementalindex逐齿分度3．Indexgears分度齿轮4．Indexinterval分度跳跃齿齿数5．Indexplate分度盘6．Indextolerance分度公差7．Indexvariation分度变化量8．Indicatoranchorage指示表支撑座9．Inertiafactor惯量系数10．Initialpitting初期点蚀11．Inneraddendum小端齿顶高12．Innerconedistance小端锥距13．Innerdedendum小端齿根高14．Innerslotwidth小端槽宽15．Innerspiralangle小端螺旋角16．Insertedbladecutter镶片刀盘17．Insideblade内切刀齿18．Insidepointdiameter内切刀尖直径19．Instantaneouscontactpattern瞬时接触斑点20．Interference 干涉21．Interferencepoint干涉点22．Interlockingdisc-millcutters交错齿盘形铣刀23．Intermittentindex间断分度24．Internalbevelgear内锥齿轮25．Inversegearratio反齿数比26．Involute渐开线27．Involutegear渐开线齿轮28．Involuteinterferencepoint渐开线干涉点29．Involutespiralangle渐开线螺旋角30．Involuteteeth渐开线齿J.1．Jetlubrication喷射润滑L.1．Lame顶根接触2．Lapping研磨3．Leadcam导程凸轮4．Lengthofaction啮合长度5．Lengthwisebridge纵向桥型接触6．Lengthwisemismatch 纵向失配7．Lengthwiseslidingvelocity纵向滑动速度8．Lifefactor 寿命系数9．Lift垂直位移10．Limitpointwidth极限刀顶距11．Limitpressureangle极限压力角12．Lineardisplacementtransducer线性位移传感器13．Lineofaction啮合线14．Lineofcenters中心线15．Lineofcontact接触线16．Loadsharingratio负荷分配比17．Localizedtoothcontact 齿局部接触18．Locatingsurface定位表面19．Long-and-short-addendumteeth高变位齿轮20．Long-toe-short-heel小端长，大端短接触21．Lubricant润滑剂22．Lubrication润滑23．Lubricity润滑性M.1．Machinecenter基床中心点2．Machinecentertoback机床中心至工件安装基准面3．Machineplane机床切削平面4．Machinerootangle毛坯安装角5．Markingcompound检查齿轮啮合型情况使用的涂色剂6．Masterblade标准刀齿7．Mastergear标准齿轮8．Meanaddendum中点齿顶高9．Meanconedistance中点锥距10．Meandedendum中点齿根高11．Meandiametralpitch中点径节WORD格式12．Meanmeasuringaddendum中点测量齿顶高13．Meanmeasuringdepth中点测量齿高14．Meanmeasuringthickness中点测量厚度15．Meannormalbasepitch中点法向基节16．Meannormaldiameterpitch中点法向径节17．Meannormalmodule中点法向模数18．Meanpoint中点，平均点19．Meanradius中点半径20．Meansection中点截面21．Meanslotwidth中点齿槽宽22．Meanspiralangle中点螺旋角23．Measuringaddendum 测量齿顶高24．Measuringtooththickness测量齿厚25．Member齿轮，元件26．Meshpoint啮合点27．Minimumslotwidth最小槽宽28．Mismatch失配29．Mitergears等齿数整角锥齿轮副30．Mixedlubrication混合润滑31．Modifiedcontactratio修正总重合度32．Modifiedroll滚修正比33．Module模数34．Motioncurves运动曲线35．Motortorque电机扭矩36．Mountingdistance安装距37．Mountingsurface安装面N.1．Narrow-tow-wide-heel小端窄大端宽接触2．Noload空载3．Nominal名义4．Non-generatedgear非展成大轮5．Normal法向，法线，法面6．Normalbacklash法向侧隙7．Normalbacklashtolerance法向侧隙公差8．Normalbasepitch法向基节9．Normalchordaladdendum法向弦齿高10．Normalchordalthickness法向弦齿厚11．Normalcircularpitch 法向周节12．Normalcircularthickness法向弧齿厚13．Normalcontactratio法向重合度14．Normaldiametralpitch法向径节15．Normaldirection法线方向16．Normal(perpendicular)load法向（垂直）负载17．Normalmodule法向模数18．Normalplane法向平面19．Normalpressureangle法向压力角20．Normalsection法向截面21．Normalspace-widthtaper正常齿槽宽收缩22．Normalthicknesstaper正常齿厚收缩23．Normaltilt法向刀倾24．Normalwear正常磨损25．No-rollroughing无滚动粗切26．Numberofteeth齿数O．1．Octoidteeth锥齿轮的“8字”啮合2．Offset偏置距3．Operatingload工作负荷4．Operatingpressureangle工作压力角5．Operatingtorque工作扭矩6．Outeraddendum大端齿顶高7．Outerconedistance外锥距8．Outerdedendum大端齿根高9．Outerslotwidth大端槽宽10．Outerspiralangle大端螺旋角11．Outsideblade外切刃点12．Outsidediameter外径，大端直径13．Outsidepointdiameter外切刀尖直径14．Outsideradius齿顶圆半径15．Outsidesurface外表面16．Overhungmounting双支承安装17．Overloadbreakage 超负荷破裂18．Overloadfactor超负荷系数P.1．Pathofaction啮合点轨迹2．Pathofcontact接触迹3．Peakload峰值负荷4．Peaktorque峰值扭矩5．Pedestalbearings安装差速器壳的架座轴承6．Performancetorque性能扭矩7．Perim-mate研磨锥齿轮和准双面齿轮用的全齿面研磨法8．Pinion小轮9．Pinionaxialdisplacement小轮轴向位移10．Pinioncone小轮锥距11．Pinionfrontbearing小轮前端轴承12．Pinionheadbearing 小轮后端前轴承13．Pinionrearbearing小轮后端后轴承14．Pinionrougher小轮粗切机15．Pinionoffset小轮偏置距16．Pitch节距，齿距17．Pitchangle节锥角18．Pitchapex节锥顶19．Pitchapexbeyondcrossingpoint节锥顶超出至相错点20．Pitchapextoback节锥顶至安装端面21．Pitchapextocrown节锥顶至轮冠22．Pitchcircle节圆23．Pitchcone节锥24．Pitchcurve节面曲线25．Pitchdiameter节径26．Pitchelement节面母线27．Pitchline节线28．Pitch-linechuck节圆夹具29．Pitch-linerunout节线跳动30．Pitchplane节面31．Pitchpoint节点32．Pitchradius节圆半径33．Pitchsurfaces节曲面34．Pitchtolerance齿距公差35．Pitchtrace节线36．Pitchvariation齿距变化量37．Pitting点蚀38．Planeofaction啮合平面39．Planeofrotation旋转平面40．Planninggenerator展成法刨齿机41．Plasticdeformation 塑性变形42．Plasticflow塑性流动43．Plateindex分度盘44．Pointdiameter刀尖直径45．Pointofcontact接触点46．Pointradius刀尖半径47．Pointwidth刀顶距48．Pointwidthtaper刀顶距收缩49．Pressurelubrication压力润滑50．Primemovertorque原动机扭矩51．Profileangle齿廓角52．Profilebridge齿廓桥形接触53．Profilecontactratio齿廓重合度54．Profilemismatch齿廓啮合失配55．Profileradiusofcurvature齿廓曲率半径56．Proofsurface检测基准面Q．1．Qualitymeasurementsystem质量检测系统2．Quenchingcracks淬火裂纹3．Quenchingdie淬火压模4．Quenchingpress淬火压床R．1．Rack齿条2．Radial径向刀位3．Radialload径向负荷4．Radiallocatingsurface径向定位表面5．Radialrakeangle径向前角6．Ratiocontrolroughing变滚比粗切7．Ratiogears滚比挂轮8．Ratioofroll滚比9．Ratioofrollgears滚比挂轮10．Recessaction啮出11．Relativedisplacement相对位移12．Relativemovement相对运动13．Relativeradiusofcurvature相对曲率半径14．Residualstress残余应力15．Revacycle直齿锥齿轮圆拉法用机床及刀具16．Revex直齿锥齿轮粗拉法17．Ridg-AC镶片圆盘端面粗铣刀18．Ridging沟条变形19．Ringgear大轮，环形齿轮20．Rippling振纹21．Rollcentering滚动定心22．Rollqueching滚动式淬火压床23．Rollgears摆角挂轮24．Rolling滚轧25．Rollingvelocity滚动速度26．Rootangle根锥角27．Rootangletilt齿根角倾斜28．Rootapex根锥顶29．Rootapexbeyondcrossingpoint根锥顶至相错点的距离30．Rootapextoback根锥顶至安装基准面距离31．Rootcircle齿根圆32．Rootcone根锥33．Rootdiameter根圆直径34．Rootline齿根线35．Rootradius根圆半径36．Rootsurface齿根曲面37．Roughac弧齿锥齿轮粗切刀38．Rougher粗切机39．RSR弧齿锥齿轮条形刀齿铣刀盘40．Runout径向跳动41．Runouttolerance径向跳动公差S.1．Scoring胶合2．Scoringindex胶合指数3．Scuffing胶合4．Sector扇形齿／齿弧5．Segment扇形齿／体6．Segmental-bladecutter大轮精切刀7．Separation分离间隙8．Separatingfactor分离系数9．Separatingforce分离力10．Set-in补充切入，进刀11．Set-over补充转角，调整转换12．Shaftangle轴转角13．Shotpeening喷丸强化14．Sidebank边频15．Sidemovement侧向位移16．Siderakeangle侧前角17．Singlecycle单循环法18．Singleroll单滚动19．Singlesetting单面调整法20．Singleside单面精切法21．Single-sidetaper齿槽收缩22．Sizefactor尺寸系数23．Skewbevelgears斜直齿锥齿轮24．Skipindex跳齿分度25．Slide-rollratio单位滑滚比，比滑26．Slidingbase床鞍，滑座27．Slidingbasesetting床鞍调整，滑座调整28．Slidingvelocity滑动速度29．Slip-chip直齿锥齿轮一次成形刀30．Sliptorque滑移扭矩31．Slottingtool切槽刀32．Slotwidth槽宽33．Slot-widthtaper槽宽收缩34．Smallcutterdevelopment小刀盘试切，能产生接近渐开线的刀具35．Solidcutter整体刀盘36．Soundtest噪声试验37．Space-widthtaper齿距收缩38．Spacingtolerance齿距公差39．Spacingvariation齿距变动量40．Spalling剥落41．Specificsliding单位滑动比42．Speedgears速度挂轮43．Sphericalinvoluteteeth球面渐开线齿44．Sphericalimaconteeth球面钳线齿45．Spindlerotationangle主轴旋转角46．Spiralangle螺旋角47．Spiralbevelgears弧齿锥齿轮48．Splashlubrication飞溅润滑49．Splitprofile齿型中断50．Spreadblade双面刀51．Spreadblade双面刀渐缩52．Standarddepthwisetaper标准深锥度53．Standardtaper正常收缩54．Standardthickness正常齿厚收缩55．Stockallowance毛坯加工流量56．Straddlecutter双列刀齿刀盘57．Straddlemounting跨装58．Straightbevelgears直齿锥齿轮59．Strengthfactor强度系数60．Stressconcentrationfactor应力集中系数61．Stubteeth短齿62．Subsurfaceinitiatedfatiguebreakage金属表面斜层初始疲劳破裂63．Summaryofmachinesettings机床调整卡64．Sumplubrication油槽润滑65．Sumvelocity总速度66．Surfaceasperities表面粗糙度67．Surfaceconditionfactor表面条件系数68．Surfacedeformation表面变形69．Surfacedurability表面耐久度70．Surfacefatigue表面疲劳71．Surfaceinitiatedfatiguebreakage表面初始疲劳破裂72．Surfaceofaction啮合面73．Surfaceofrevolution回转面74．Surfacetreatment表面处理75．Swingingbase回转底座76．Swingpinioncone摆动小轮节锥法77．Swivel刀转78．Swivelangle刀转角79．Symmetricalrack对称齿条80．Symmetricalrackproportions对称齿条比例T.1．Tangentialload切向负荷2．Tangentplane切平面3．Tanline小轮夹具4．Tanruf双联粗切刀，8.5模数一下5．Tan-tru用在加工1016－2540mm的锥齿刀具6．Taperroughing具有刀顶距收缩的大小轮粗切过程7．Temperaturefactor温度系数8．Testingmachine试验机9．Thicknesstaper齿厚收缩10．Tilt刀倾11．Tiltangle刀倾角12．Tiltedrootlinetaper倾斜齿根收缩13．Tipradius齿顶圆角半径14．Toe轮齿小端15．Toepattern小端接触16．Tool刀具17．Tooladvance刀具进刀18．Tooledgeradius刀刃圆角半径19．Toolpointwidth刀顶距20．Toothangle齿角21．Toothbearing齿支撑面，轮齿接触面22．Toothcontactanalysis轮齿接触分析23．Toothcontactpattern 轮齿接触斑点24．T oothhorizontal齿水平面25．Toothlayout轮齿剖面图26．Tooth-meshfrequency齿啮合频率27．Toothnumber齿数28．Toothprofile齿形，齿廓29．Toothspacingtesting齿距检查仪30．Toothspiral齿螺旋线31．Toothsurface轮齿表面32．Toothtaper轮齿收缩33．Tooth-to-toothcompositetolerance一齿度量中心距公差34．Tooth-to-Toothcompositevariation一齿度量中心距变量35．Toothtrace齿线36．Toothvertical齿垂直面37．Top齿顶38．Topland齿顶面39．Toplandwidth齿顶面宽度40．Topping修顶41．Topreliefangle顶刃后角42．Toprem修根刀片43．Topremangle刀齿突角角度44．Topslopeangle刀齿顶刃倾角45．Totalcompositetolerance总综合公差46．Totalcompositevariation总度量中心距变动量47．Totalcontactratio总重合度48．T otalindextolerance总分度公差49．T otalindexvariation总分度变动量50．Tractiveefforttorque 牵引力扭矩51．Transversecircularpitch端面周节52．Transversecircularthickness端面弧齿厚53．Transversecontactratio端面重合度54．Transversediametralpitch端面径节55．Transversemodule端面模数56．Transverseplane端平面57．Transversepressureangle 端面压力角58．Transversespace-widthtaper端面槽宽收缩59．Transversethicknesstaper端面齿厚收缩60．Tredgold’sapproximation背锥近似法61．Tribology润滑与磨损学62．Triplex三面刃圆盘端铣刀63．Two-toolgenerator双刀展成加工机床U.1．Undercut根切2．Undevelopedsettings试切前调整3．Uniformroll匀速滚动4．Uniformvelocitytester匀速试验机5．Uni-spand大轮心轴6．Unitload单位负荷7．Unitool曲面镶片刀8．Up-roll向上滚动V.1．VandHcheck锥齿轮啮合的VH检查2．Variableroll变滚动3．Velocityfactor速度系数4．Versacut弧齿锥齿轮加工多用刀盘5．Vers-grip卡紧小齿轮用的卡盘（商标名称）6．Verticaldirection垂直方向7．Verticaldisplacement垂直位移8．Verticalfactor垂直系数9．Verticalforce垂直力10．Verticaloffset垂直偏置距11．Verticalplane垂直面12．Virtualnumberofteeth当量齿数WORD格式13．Virtualpitchradius当量节圆半径14．Viscosity粘度15．V-toolV型刀具W.1．Waveform波形2．Wear磨损3．Webless-typegear无幅板式齿轮4．Web-typegear幅板式齿轮5．Wheelsliptorque车轮打滑扭矩6．Wholedepth齿全高7．Workhead工件头座8．Workheadoffset垂直轮位9．Workholdingequipment工件夹具10．Workingdepth工作齿高11．Workingstress工作允许应力12．Worktestsroll检验工件主轴转角X.1．X-pandisk大轮蝶形，涨胎心轴Z.1．Zerodepthwisetaper等齿高2．Zerol零度锥齿轮。