机电英语词汇
水电站机电英语专业词汇a turn 一匝 abno rmal 异常 abrasi on 磨损 abrasive test磨耗试验 abrasive wear 磨损 abutme nt 支墩 AC excitation circuit breaker 交流灭磁开 关 AC(alternati ng curre nt)交流 accepta nee交接，验收 access通路 accessories 附件 accide nt 事故 accord ing to根据，依照 accuracy class 精度等级 acetyle ne 乙炔 active power有功功率 actual size 实际尺寸 actual value 实际值 actuator执行机构 adapter 接头 additio nal 附加的 adequate适当的，足够的 adhesive带粘性的，胶粘 adjace nt邻近的，接近的 adjust pad调整垫片 adjust screw 顶丝 adjustable spa nner 活扳手 adjust ing plate 调整板 adjusti ng调节，调整 aga inst ground 对地 Ag-braze piece 银焊片 Ag-braze wire 银焊丝 Ag-welding plate 银焊片 Ag-welding rod 银焊条 AI (a nalog in put)模拟输入 air admission pipe补气管 air admission valve补气阀 air baffle plate 扌当风板 air chamber 储气罐 air compressor空 压机 air cooler空气冷去卩器 air flow bridge 风道 air gap气隙 air guide in sulated 隔离导气板 air guide 空气导板 air hous ing 风罩 air injection valve 补气阀 air空气 air-gap in ducti on 气隙磁密 air-ve nts通风沟 air-water heat excha nger 空气冷却器 alarm报警 alignment同轴性 alkali-less glass tape无 碱带 alloy轴承合金 alternating circuit 交流电路 alter nat ing curre nt 交流电 assembly装配，组装 assert坚持，表明 assessme nt 评估 assume承担 atmospheric pressure 大气压力 authorizati on 许可，授权 authorize 授权 auto con trol mode自动控制模式 automatic 自动 auxiliary circuit辅助设备电路 auxiliary connection 辅助接线 auxiliary in put 辅助电源 auxiliary tube 辅助套管 auxiliary辅助的 available有效的 AVR(auto voltage regulating)自动电压调 节 axial轴向 axis轴线
Babbitt layer巴氏合金 backgro und no ise 背景噪音 backup做备份 baffle plate隔板,挡板 bala nee level 水准仪 bala ncing pipe 平压管 ball valve 球阀 band 带 bar条，线棒 bare 裸 bare ness赤裸，裸露
alternator交流发电机 ambie nt temperature环境温度 ammeter 电表 amount数量 amperage安 培数 ampere-tur ns 安匝 amplifier放大器 an alog模拟量 an chor bolt 锚栓 an gle grin der 角磨机 an gle iron 角铁 an gle角度，角铁 an gular velocity 角速度 annihilate取消，削弱 anti corona paint 防晕漆 an ti-rotati on device 抗旋转装置 AO (an alog output)模拟输出 apparatus器械，设备，仪器 appare ntly 显然地 applicable 可用 applied 应用 approval认可，批准 approximately 大约 arc电弧 arm支臂 armature reacti on 电枢反应 armature 电枢 arrow箭头记号 asbestos 石棉 assemble装酉己 barometer tube 测压管 base impeda nee 阻抗基值 base基础 battery 电池 beam横梁
beari ng eleara nee瓦间隙 beari ng cover轴承盖板 bearing journal 轴领
bearing key 轴承键 beari ng metal temperature 瓦温 bearing pad 轴瓦
beari ng support 轴承支架 beari ng忍受，轴承
bell housing外壳,外罩,外箱 bend tube 弯管 between center 中心间距 bimetal双金属材料 binary开关量 blade叶片
bla nking plug 截止塞 bleachi ng sand 漂白沙 blind挡板，盲板 block shim 垫块
block搭块，间隔块，块，堵塞 blocking堵塞，屏蔽
board配电盘柜 bolt for holding 吊环螺钉 bolt plug 螺塞 bolt螺杆，螺栓 bolting螺栓连接，拧紧
bonding age nt 粘接剂 bore钻孑L
bottom layer 下层 bottom ring 底环 boucho n 衬套 box盒
bracket hub机架中心体 bracket支架，托架
brake and jacking cylinder 希9动及顶起汽 缸 brake dust suction system 制动粉尘系统 brake dust制动粉尘 brake shoe 闸皮 brake制9动
braking制动，（用闸）减速 breakdow n voltage 击穿电压 breaker failure断路器失灵 breaker断路器
break ing pin 剪断销 briefly简单地 broke n中断 brush holder 刷架 brush support 刷握 brush电刷 build into安装在
buried cable埋地电缆 burr毛边 bus bar母线 bush衬套 bush ing 套管 butterfly valve 蝶阀 buzzer蜂鸣器 bypass旁路 byte字节，8元件组 cab inet 柜 cable ladder梯形电缆架 cable tie电缆扎带 cable trays电缆托架 cage end rings 阻尼环 cage 笼 calculate 计算 calculated to 换算至 calibrator 口径测量器 cam凸轮 cap screw 半圆头螺钉 capacita nee容量，容抗 capacitive level measureme nt 容性液位测
量 capacitor电容器 capacity容量，容积，电容 carb on brush 碳刷 carb on dioxide 二氧化碳 carb on dust suction device 碳粉吸收装置 carb on mono xide 一氧化碳 carb on 碳 carpet 毡 cavetto/key 槽 / 键 C-clamp C 型夹 ceiling 顶值 cen ter line 中心线
cen ter sunk screw 沉头螺钉 cen trifugal pen dulum 离心摆 cen trifuge 离心的 certificate 证明书 cha in pulley手拉葫芦 cha in —连串，链 chalk粉笔 chamber腔，洞室 chamfer 倒角 cha nge over 切换 cha nnel 通道 characteristic 特性，特征 charge电荷，负载 check valve直通单向阀，止回阀 check检查 choice选择 circle top screw 圆头螺钉 circle圆，圆周 circuit breaker 断路器 circuit电路，回路 circular degree 圆度 claim要求 clamp block 夹板 clamp夹具 clamping bolt磁轭拉紧螺杆 clamp ing device 连接装置 clamping plate 夹板，压板 class of in sulati on 绝缘等级 cleara nee 间隙 client客户
机械专业英语词汇
机械专业英语词汇金属切削metal cutting机床machine tool金属工艺学technology of metals刀具cutter摩擦friction联结link传动drive/transmission轴shaft弹性elasticity频率特性frequency characteristic误差error响应response定位allocation机床夹具jig动力学dynamic运动学kinematic静力学static分析力学analyse mechanics拉伸pulling压缩hitting剪切shear扭转twist弯曲应力bending stress强度intensity三相交流电three-phase AC磁路magnetic circles变压器transformer异步电动机asynchronous motor几何形状geometrical精度precision正弦形的sinusoid交流电路AC circuit机械加工余量machining allowance变形力deforming force变形deformation应力stress硬度rigidity热处理heat treatment退火anneal正火normalizing脱碳decarburization渗碳carburization电路circuit半导体元件semiconductor element反馈feedback发生器generator直流电源DC electrical source门电路gate circuit逻辑代数logic algebra外圆磨削external grinding内圆磨削internal grinding平面磨削plane grinding变速箱gearbox离合器clutch绞孔fraising绞刀reamer螺纹加工thread processing螺钉screw铣削mill铣刀milling cutter功率power工件workpiece齿轮加工gear mechining齿轮gear主运动main movement主运动方向direction of main movement进给方向direction of feed进给运动feed movement合成进给运动resultant movement of feed合成切削运动resultant movement of cutting合成切削运动方向direction of resultant movement of cutting 切削深度cutting depth前刀面rake face刀尖nose of tool前角rake angle后角 clearance angle龙门刨削 planing主轴 spindle主轴箱 headstock卡盘 chuck加工中心 machining center车刀 lathe tool车床 lathe钻削镗削 bore车削 turning磨床 grinder基准 benchmark钳工 locksmith锻 forge压模 stamping焊 weld拉床 broaching machine拉孔 broaching装配 assembling铸造 found流体动力学 fluid dynamics流体力学 fluid mechanics加工 machining液压 hydraulic pressure切线 tangent机电一体化 mechanotronics mechanical-electrical integration 气压 air pressure pneumatic pressure稳定性 stability介质 medium液压驱动泵 fluid clutch液压泵 hydraulic pump阀门 valve失效 invalidation强度 intensity载荷 load应力 stress安全系数 safty factor可靠性 reliability螺纹 thread螺旋 helix键 spline销 pin滚动轴承 rolling bearing滑动轴承 sliding bearing弹簧 spring制动器 arrester brake十字结联轴节 crosshead联轴器 coupling链 chain皮带 strap精加工 finish machining粗加工 rough machining变速箱体 gearbox casing腐蚀 rust氧化 oxidation磨损 wear耐用度 durability随机信号 random signal离散信号 discrete signal超声传感器 ultrasonic sensor集成电路 integrate circuit挡板 orifice plate残余应力 residual stress套筒 sleeve扭力 torsion冷加工 cold machining电动机 electromotor汽缸 cylinder过盈配合 interference fit热加工 hotwork摄像头 CCD camera倒角 rounding chamfer优化设计 optimal design工业造型设计 industrial moulding design有限元 finite element滚齿 hobbing插齿 gear shaping伺服电机 actuating motor铣床 milling machine钻床 drill machine镗床 boring machine步进电机 stepper motor丝杠 screw rod导轨 lead rail组件 subassembly可编程序逻辑控制器 Programmable Logic Controller PLC 电火花加工 electric spark machining电火花线切割加工 electrical discharge wire - cutting 相图 phase diagram热处理 heat treatment固态相变 solid state phase changes有色金属 nonferrous metal陶瓷 ceramics 合成纤维 synthetic fibre电化学腐蚀 electrochemical corrosion车架 automotive chassis悬架 suspension转向器 redirector变速器 speed changer板料冲压 sheet metal parts孔加工 spot facing machining车间 workshop工程技术人员 engineer气动夹紧 pneuma lock数学模型 mathematical model画法几何 descriptive geometry机械制图 Mechanical drawing投影 projection视图 view剖视图 profile chart标准件 standard component零件图 part drawing装配图 assembly drawing尺寸标注 size marking技术要求 technical requirements刚度 rigidity内力 internal force位移 displacement截面 section疲劳极限 fatigue limit断裂 fracture塑性变形 plastic distortion脆性材料 brittleness material刚度准则 rigidity criterion垫圈 washer垫片 spacer直齿圆柱齿轮 straight toothed spur gear 斜齿圆柱齿轮 helical-spur gear直齿锥齿轮 straight bevel gear运动简图 kinematic sketch齿轮齿条 pinion and rack蜗杆蜗轮 worm and worm gear虚约束 passive constraint曲柄 crank摇杆 racker凸轮 cams共轭曲线 conjugate curve范成法 generation method定义域 definitional domain值域 range导数\\微分 differential coefficient求导 derivation定积分 definite integral不定积分 indefinite integral曲率 curvature偏微分 partial differential毛坯 rough游标卡尺 slide caliper千分尺 micrometer calipers攻丝 tap二阶行列式 second order determinant逆矩阵 inverse matrix线性方程组 linear equations概率 probability随机变量 random variable排列组合 permutation and combination气体状态方程 equation of state of gas动能 kinetic energy势能 potential energy机械能守恒 conservation of mechanical energy 动量 momentum桁架 truss轴线 axes余子式 cofactor逻辑电路 logic circuit触发器 flip-flop脉冲波形 pulse shape数模 digital analogy液压传动机构 fluid drive mechanism机械零件 mechanical parts淬火冷却 quench淬火 hardening回火 tempering调质 hardening and tempering磨粒 abrasive grain结合剂 bonding agent砂轮 grinding wheelair permeability test 透气性试验austenitic steel 沃斯田铁钢brinell hardness 布耐内尔硬度brinell hardness test 布氏硬度试验charpy impact test 夏比冲击试验conical cup test 圆锥杯突试验cup flow test 杯模式流动度试验dart drop impact test 落锤冲击试验Elmendorf test 埃罗门多撕裂强度试验environmental stress cracking test 环境应力龟裂试验ericessen test 埃留伸薄板拉伸试验falling ball impact test 落球冲击试验fatigue test 疲劳试验ferrite 纯铁体gantt chart 甘特图heat cycle test 热循环试验histogram 柱状图hot bend test 热弯试验izod impact test 埃左德冲击试验loop tenacity 环结强度martens heat distortion temperature test 马顿斯耐热试验martensite 马氏体mullen bursting strength tester 密廉式破裂强度试验机nol ring test 诺尔环试验normal distribution 常态分配ozone resistance test 抗臭氧试验pareto diagram 柏拉图peeling test 剥离试验pinhole test 针孔试验机rattler test 磨耗试验rockweel hardness test 洛氏硬度试验rockweel hardness 洛氏威尔硬度rolinx process 罗林克斯射出压缩成形法rossi-peakes flow test 罗西皮克斯流动试验sampling inspection 抽样检查scratch hardness 抗刮硬度shore hardness 萧氏硬度spiral flow test 螺旋流动试验surface abrasion test 表面磨耗试验taber abraser 泰伯磨耗试验机tensile impact test 拉伸冲击试验tensile strength 抗拉强度tension test 张力试验thermal shock test 冷热剧变试验torsion test 扭曲试验ubbelohde viscometer 乌别洛德黏度计vicat indentation test 维卡针压陷试验Vickers hardness test 维氏硬度试验warpage test 翘曲试验autocollimator 自动准直机bench comparator 比长仪block gauge 块规bore check 精密小测定器calibration 校准caliper gauge 卡规check gauge 校对规clearance gauge 间隙规clinoretee 测斜仪comparator 比测仪cylinder square 圆筒直尺depth gauge 测深规dial indicator 针盘指示表dial snap gauge 卡规digital micrometer 数位式测微计feeler gauge 测隙规gauge plate 量规定位板height gauge 测高规inside calipers 内卡钳inside micrometer 内分??卡interferometer 干涉仪leveling block 平台limit gauge 限规micrometer 测微计mil 千分之一寸monometer 压力计morse taper gauge 莫氏锥度量规nonius 游标卡尺optical flat 光学平晶optical parallel 光学平行passimeter 内径仪position scale 位置刻度profile projector 轮廓光学投影仪protractor 分角器radius 半径ring gauge 环规sine bar 正弦量规snap gauge 卡模square master 直角尺stylus 触针telescopic gauge 伸缩性量规working gauge 工作量规weatherometer 人工老化试验机weissenberg effect 威森伯格回转效应。
机械专业英语词汇汇总
机械专业英语词汇（大全）金属切削metal cutting 机床machine tool 金属工艺学technology of metals 刀具cutter 摩擦friction 联结link 传动drive/transmission 轴shaft 弹性elasticity 频率特性frequency characteristic 误差error 响应response 定位allocation 机床夹具jig 动力学dynamic 运动学kinematic 静力学static分析力学analyse mechanics 拉伸pulling 压缩hitting剪切shear 扭转twist 弯曲应力bending stress强度intensity 三相交流电three-phase AC 磁路magnetic circles变压器transformer 异步电动机asynchronous motor几何形状geometrical 精度precision 正弦形的sinusoid交流电路AC circuit 机械加工余量machining allowance变形力deforming force 变形deformation 应力stress硬度rigidity 热处理heat treatment 退火anneal正火normalizing 脱碳decarburization 渗碳carburization电路circuit 半导体元件semiconductor element反馈feedback 发生器generator 直流电源DC electrical source门电路gate circuit 逻辑代数logic algebra 外圆磨削external grinding 内圆磨削internal grinding 平面磨削plane grinding 变速箱gearbox 离合器clutch绞孔fraising 绞刀reamer 螺纹加工thread processing螺钉screw 铣削mill 铣刀milling cutter 功率power 工件workpiece 齿轮加工gear mechining齿轮gear 主运动main movement 主运动方向direction of main movement进给方向direction of feed 进给运动feed movement合成进给运动resultant movement of feed 合成切削运动resultant movement of cutting合成切削运动方向direction of resultant movement of cutting切削深度cutting depth 前刀面rake face刀尖nose of tool 前角rake angle 后角clearance angle 龙门刨削planing 主轴spindle主轴箱headstock 卡盘chuck 加工中心machining center车刀lathe tool 车床lathe 钻削镗削bore车削turning 磨床grinder 基准benchmark钳工locksmith 锻forge 压模stamping焊weld 拉床broaching machine 拉孔broaching装配assembling 铸造found 流体动力学fluid dynamics流体力学fluid mechanics 加工machining 液压hydraulic pressure切线tangent 机电一体化mechanotronics mechanical-electrical integration气压air pressure pneumatic pressure 稳定性stability 介质medium 液压驱动泵fluid clutch液压泵hydraulic pump 阀门valve 失效invalidation强度intensity 载荷load 应力stress安全系数safty factor 可靠性reliability 螺纹thread螺旋helix 键spline 销pin 滚动轴承rolling bearing滑动轴承sliding bearing 弹簧spring制动器arrester brake 十字结联轴节crosshead 联轴器coupling链chain 皮带strap 精加工finish machining粗加工rough machining 变速箱体gearbox casing腐蚀rust 氧化oxidation 磨损wear耐用度durability 随机信号random signal 离散信号discrete signal超声传感器ultrasonic sensor 集成电路integrate circuit挡板orifice plate 残余应力residual stress 套筒sleeve 扭力torsion 冷加工cold machining 电动机electromotor 汽缸cylinder 过盈配合interference fit热加工hotwork 摄像头CCD camera 倒角rounding chamfer优化设计optimal design 工业造型设计industrial moulding design有限元finite element 滚齿hobbing插齿gear shaping 伺服电机actuating motor 铣床milling machine钻床drill machine 镗床boring machine步进电机stepper motor 丝杠screw rod 导轨lead rail组件subassembly 可编程序逻辑控制器Programmable Logic Controller PLC电火花加工electric spark machining 电火花线切割加工electrical discharge wire - cutting 相图phase diagram 热处理heat treatment固态相变solid state phase changes 有色金属nonferrous metal陶瓷ceramics 合成纤维synthetic fibre电化学腐蚀electrochemical corrosion 车架automotive chassis悬架suspension 转向器redirector 变速器speed changer板料冲压sheet metal parts 孔加工spot facing machining车间workshop 工程技术人员engineer 气动夹紧pneuma lock数学模型mathematical model 画法几何descriptive geometry机械制图Mechanical drawing 投影projection视图view 剖视图profile chart 规范件standard component零件图part drawing 装配图assembly drawing尺寸标注size marking 技术要求technical requirements刚度rigidity 内力internal force 位移displacement截面section 疲劳极限fatigue limit 断裂fracture 塑性变形plastic distortion 脆性材料brittleness material刚度准则rigidity criterion 垫圈washer垫片spacer 直齿圆柱齿轮straight toothed spur gear斜齿圆柱齿轮helical-spur gear 直齿锥齿轮straight bevel gear 运动简图kinematic sketch 齿轮齿条pinion and rack 蜗杆蜗轮worm and worm gear 虚约束passive constraint曲柄crank 摇杆racker 凸轮cams共轭曲线conjugate curve 范成法generation method 定义域definitional domain 值域range 导数\\微分differential coefficient求导derivation 定积分definite integral不定积分indefinite integral 曲率curvature偏微分partial differential 毛坯rough游标卡尺slide caliper 千分尺micrometer calipers 攻丝tap 二阶行列式second order determinant 逆矩阵inverse matrix线性方程组linear equations 概率probability随机变量random variable 排列组合permutation and combination气体状态方程equation of state of gas 动能kinetic energy势能potential energy 机械能守恒conservation of mechanical energy动量momentum 桁架truss 轴线axes余子式cofactor 逻辑电路logic circuit 触发器flip-flop脉冲波形pulse shape 数模digital analogy 液压传动机构fluid drive mechanism 机械零件mechanical parts淬火冷却quench 淬火hardening 回火tempering 调质hardening and tempering 磨粒abrasive grain 结合剂bonding agent 砂轮grinding wheel。
机械专业英语词汇(很全)
安全系数 safty factor调质 hardening and tempering板料冲压 sheet metal parts定积分 definite integral半导体元件 semiconductor element定位 allocation变速器 speed changer定义域 definitional domain变速箱 gearbox动力学 dynamic变速箱体 gearbox casing动量 momentum变形 deformation动能 kinetic energy变形力 deforming force断裂 fracture变压器 transformer锻 forge标准件 standard component二阶行列式 second order determinant不定积分 indefinite integral发生器 generator步进电机 stepper motor阀门 valve残余应力 residual stress反馈 feedback插齿 gear shaping范成法 generation method超声传感器 ultrasonic sensor分析力学 analyse mechanics车床 lathe腐蚀 rust车刀 lathe tool概率 probability车架 automotive chassis刚度 rigidity车间 workshop刚度准则 rigidity criterion车削 turning工程技术人员 engineer尺寸标注 size marking工件 workpiece齿轮 gear工业造型设计 industrial moulding design 齿轮齿条 pinion and rack功率 power齿轮加工 gear mechining攻丝 tap触发器 flip-flop共轭曲线 conjugate curve传动 drive/transmission固态相变 solid state phase changes磁路 magnetic circles滚齿 hobbing粗加工 rough machining滚动轴承 rolling bearing脆性材料 brittleness material过盈配合 interference fit淬火 hardening焊 weld淬火冷却 quench合成进给运动 resultant movement of feed弹簧 spring 合成切削运动resultant movement of cutting弹性 elasticity 合成切削运动方向direction of resultant movement of cutting挡板 orifice plate合成纤维 synthetic fibre刀尖 nose of tool桁架 truss刀具 cutter后角 clearance angle导轨 lead rail滑动轴承 sliding bearing导数\\微分 differential coefficient画法几何 descriptive geometry 倒角 rounding chamfer回火 tempering电动机 electromotor机床 machine tool电化学腐蚀 electrochemical corrosion机床夹具 jig电火花加工 electric spark machining 机电一体化 mechanotronics mechanical-electrical integration电火花线切割加工 electrical dischargewire - cutting机械专业英语词汇（很全）电路 circuit螺钉 screw垫片 spacer螺纹 thread垫圈 washer螺纹加工 thread processing机械加工余量 machining allowance螺旋 helix机械零件 mechanical parts脉冲波形 pulse shape机械能守恒 conservation of mechanical毛坯 roughenergy机械制图 Mechanical drawing门电路 gate circuit基准 benchmark摩擦 friction集成电路 integrate circuit磨床 grinder几何形状 geometrical磨粒 abrasive grain技术要求 technical requirements磨损 wear加工 machining内力 internal force加工中心 machining center内圆磨削 internal grinding剪切 shear耐用度 durability键 spline逆矩阵 inverse matrix交流电路 AC circuit扭力 torsion绞刀 reamer扭转 twist绞孔 fraising排列组合 permutation and combination 结合剂 bonding agent皮带 strap截面 section疲劳极限 fatigue limit介质 medium偏微分 partial differential金属工艺学 technology of metals频率特性 frequency characteristic金属切削 metal cutting平面磨削 plane grinding进给方向 direction of feed剖视图 profile chart进给运动 feed movement气动夹紧 pneuma lock精度 precision气体状态方程 equation of state of gas 精加工 finish machining气压 air pressure pneumatic pressure 静力学 static汽缸 cylinder卡盘 chuck千分尺 micrometer calipers可编程序逻辑控制器 Programmable Logic前刀面 rake faceController PLC可靠性 reliability钳工 locksmith孔加工 spot facing machining强度 intensity拉床 broaching machine强度 intensity拉孔 broaching切线 tangent拉伸 pulling切削深度 cutting depth冷加工 cold machining求导 derivation离合器 clutch曲柄 crank离散信号 discrete signal曲率 curvature联结 link热处理 heat treatment联轴器 coupling热处理 heat treatment链 chain热加工 hotwork零件图 part drawing三相交流电 three-phase AC流体动力学 fluid dynamics砂轮 grinding wheel流体力学 fluid mechanics摄像头 CCD camera龙门刨削 planing渗碳 carburization逻辑代数 logic algebra失效 invalidation逻辑电路 logic circuit十字结联轴节 crosshead势能 potential energy运动简图 kinematic sketch视图 view运动学 kinematic数模 digital analogy载荷 load数学模型 mathematical model正火 normalizing丝杠 screw rod正弦形的 sinusoid伺服电机 actuating motor直齿圆柱齿轮 straight toothed spur gear 塑性变形 plastic distortion直齿锥齿轮 straight bevel gear随机变量 random variable直流电源 DC electrical source随机信号 random signal值域 range镗床 boring machine制动器 arrester brake陶瓷 ceramics轴 shaft套筒 sleeve轴线 axes投影 projection主运动 main movement凸轮 cams主运动方向 direction of main movement 退火 anneal主轴 spindle脱碳 decarburization主轴箱 headstock外圆磨削 external grinding铸造 found弯曲应力 bending stress转向器 redirector位移 displacement装配 assembling稳定性 stability装配图 assembly drawing蜗杆蜗轮 worm and worm gear组件 subassembly误差 error钻床 drill machine铣床 milling machine钻削 镗削 bore铣刀 milling cutter铣削 mill线性方程组 linear equations相图 phase diagram响应 response销 pin斜齿圆柱齿轮 helical-spur gear虚约束 passive constraint悬架 suspension压模 stamping压缩 hitting氧化 oxidation摇杆 racker液压 hydraulic pressure液压泵 hydraulic pump液压传动机构 fluid drive mechanism液压驱动泵 fluid clutch异步电动机 asynchronous motor应力 stress应力 stress硬度 rigidity优化设计 optimal design游标卡尺 slide caliper有色金属 nonferrous metal有限元 finite element余子式 cofactor。
机械工业专业英语词汇
机械工业专业英语词汇金属切削 metal cutting 机床 machine tool金属工艺学 technology of metals 刀具 cutter摩擦 friction 联结 link传动 drive/transmission 轴 shaft弹性 elasticity 频率特性 frequency characteristic误差 error 响应 response定位 allocation 机床夹具 jig动力学 dynamic 运动学 kinematic静力学 static 分析力学 analyse mechanics拉伸 pulling 压缩 hitting剪切 shear 扭转 twist弯曲应力 bending stress 强度 intensity三相交流电 three-phase AC 磁路 magnetic circles变压器 transformer 异步电动机 asynchronous motor几何形状 geometrical 精度 precision正弦形的 sinusoid 交流电路 AC circuit机械加工余量 machining allowance 变形力 deforming force 变形 deformation 应力 stress硬度 rigidity 热处理 heat treatment退火 anneal 正火 normalizing脱碳 decarburization 渗碳 carburization电路 circuit 半导体元件 semiconductor element反馈 feedback 发生器 generator直流电源 DC electrical source 门电路 gate circuit逻辑代数 logic algebra 外圆磨削 external grinding内圆磨削 internal grinding 面磨削 plane grinding变速箱 gearbox 离合器 clutch绞孔 fraising 绞刀 reamer螺纹加工 thread processing 螺钉 screw铣削 mill 铣刀 milling cutter功率 power 工件 workpiece齿轮加工 gear mechining 齿轮 gear主运动 main movement 主运动方向 direction of main movement进给方向 direction of feed 进给运动 feed movement合成进给运动 resultant movement of feed 合成切削运动resultant movement of cutting合成切削运动方向 direction of resultant movement of cutting切削深度 cutting depth 前刀面 rake face刀尖 nose of tool 前角 rake angle后角 clearance angle 龙门刨削 planing主轴 spindle 主轴箱 headstock卡盘 chuck 加工中心 machining center车刀 lathe tool 车床 lathe钻削镗削 bore 车削 turning磨床 grinder 基准 benchmark钳工 locksmith 锻 forge压模 stamping 焊 weld拉床 broaching machine 拉孔 broaching装配 assembling 铸造 found流体动力学 fluid dynamics 流体力学 fluid mechanics 加工 machining 液压 hydraulic pressure切线 tangent 气压 air pressure pneumatic pressure机电一体化 mechanotronics mechanical-electrical integration稳定性 stability 介质 medium液压驱动泵 fluid clutch 液压泵 hydraulic pump阀门 valve 失效 invalidation强度 intensity 载荷 load应力 stress 安全系数 safty factor可靠性 reliability 螺纹 thread螺旋 helix 键 spline销 pin 滚动轴承 rolling bearing滑动轴承 sliding bearing 弹簧 spring制动器 arrester brake 十字结联轴节 crosshead 联轴器 coupling 链 chain皮带 strap 精加工 finish machining粗加工 rough machining 变速箱体 gearbox casing。
机械专业英语词汇【最新完整版】
螺旋helix组件subassembly
键spline可编程序逻辑控制器Programmable
销pinLogic Controller PLC
滚动轴承rolling bearing电火花加工electric spark machining
滑动轴承sliding bearing电火花线切割加工electrical discharge
Casting,copper铸铜
Casting,gray iron铸灰口铁
Casting,malleable iron可锻铸铁
Casting,other其他铸造
Casting,steel铸钢
Chain drive链传动
Chain making tools造链机
Chamfer machines倒角机
Chucks夹盘
Bearings轴承
Belt drive带传动
Bending machines弯曲机
Blades刀片
Blades,saw锯片
Bolts,screws & nuts螺栓,螺帽及螺丝
Boring heads搪孔头
Boring machines镗床
Cable making tools造线机
Casting,aluminium铸铝
误差error平面磨削plane grinding
响应response变速箱gearbox
定位allocation离合器clutch
机床夹具jig绞孔fraising
动力学dynamic绞刀reamer
运动学kinematic螺纹加工thread processing
静力学static螺钉screw
机械专业英语词汇(带音标)
机械专业英语词汇金属切削 metal cutting [英] [ˈmetl][美] [ˈmɛtl]机床 machine tool [英] [məˈʃi:n tu:l][美] [məˈʃin tul]金属工艺学 technology of metals [tekˈnɔlədʒi] [ˈmetl]刀具 cutter[D.J.:'kʌtə][K.K.:'kʌtɚ]摩擦 friction['frikʃən][’frɪkʃən]联结 link [liŋk]传动 drive/transmission [trænzˈmiʃən]轴 shaft [ʃɑ:ft]弹性 elasticity [ɪlæ'stɪsɪti:, ,i:læ-][ɪlæ'stɪsɪti, ,ilæ-]频率特性 frequency characteristic['fri:kwənsi][ˌkæriktəˈristik]误差 error[ˈerə]响应 response[ri'spɔns]定位 allocation[ˌæləˈkeiʃən]机床夹具 jig[dʒɪg]动力学 dynamic[dai'næmik]运动学 kinematic[,kaini'mætik]静力学 static[ˈstætik]分析力学 analyse mechanics[ˈænəlaiz].[mɪˈkænɪks]拉伸 pulling['puliŋ]压缩 hitting[hitiŋ]剪切 shear[ʃiə]扭转 twist[twist]弯曲应力 bending stress['bendiŋ].[stres]强度 intensity[inˈtensiti]三相交流电 three-phase AC[feiz]磁路 magnetic circles[mæɡˈnetik].[ˈsə:kl]变压器 transformer[trænsˈfɔ:mə]异步电动机 asynchronous motor[ei'siŋkrənəs]['məutə]几何形状 geometrical[dʒɪəˈmetrɪkəl]精度 precision[priˈsiʒən]正弦形的 sinusoid[ˈsainəˌsɔid]交流电路AC circuit [ˈsə:kit]机械加工余量machining allowance[mə'ʃi:niŋ].[əˈlauəns]变形力deforming force [dɪˈfɔ:miŋ].[fɔ:s]变形deformation [ˌdi:fɔ:ˈmeɪʃən, ˌdefə-]应力stress [stres]硬度rigidity [rɪˈdʒɪdɪti:]]热处理heat treatment [ˈtri:tmənt]退火anneal [əˈni:l]正火normalizing ['nɔ:məlaiziŋ]脱碳decarburization [di:,kɑ:bjuərai'zeiʃən]渗碳carburization [,kɑ:bjurai'zeiʃən]电路circuit [ˈsə:kit]半导体元件semiconductor element[ˌsemikənˈdʌktə].[ˈelimənt] 反馈feedback [ˈfi:dbæk]发生器generator [ˈdʒenəreitə]直流电源DC electrical source [i'lektrikəl].[sɔ:s]门电路gate circuit [ɡeit] [ˈsə:kit]逻辑代数logic algebra [ˈlɔdʒik] .[ˈældʒibrə]外圆磨削external grinding [eksˈtə:nl]['ɡraindiŋ]内圆磨削internal grinding [inˈtə:nəl] ['ɡraindiŋ]平面磨削plane grinding [plein] ['ɡraindiŋ]变速箱gearbox [ˈɡiəbɔks]离合器clutch [klʌtʃ]绞孔fraising [freiziŋ]绞刀reamer D.J.[ˈri:mə]螺纹加工thread processing [θred].[prəʊˈsesɪŋ]螺钉screw [skru:]铣削mill [mil]铣刀milling cutter [ˈmiliŋ].[ˈkʌtə]功率power [ˈpauə]工件workpiece [ˈwɜ:kpi:s]齿轮加工gear machining [ɡiə] [mə'ʃi:niŋ]齿轮gear [ɡiə]主运动main movement [mein].[ˈmu:vmənt]主运动方向direction of main movement [diˈrekʃən] 进给方向direction of feed [diˈrekʃən].[fi:d]进给运动feed movement [fi:d] [ˈmu:vmənt]合成进给运动resultant movement of feed [riˈzʌltənt] [ˈmu:vmənt] [fi:d]合成切削运动resultant movement of cutting[riˈzʌltənt] [ˈmu:vmənt] [ˈkʌtɪŋ]合成切削运动方向direction of resultant movement of cutting [diˈrekʃən] [riˈzʌltənt] [ˈmu:vmənt] [ˈkʌtɪŋ] 切削深度cutting depth [ˈkʌtɪŋ] .[depθ]前刀面rake face [reik][feis]刀尖nose of tool [nəuz].[tu:l]前角rake angle [reik].[ˈæŋɡl]后角clearance angle [ˈkliərəns].[ˈæŋɡl]龙门刨削planing [plæniŋ]主轴spindle [ˈspɪndl]主轴箱headstock [ˈhedstɔk]卡盘chuck [tʃʌk]加工中心machining center [mə'ʃi:niŋ]车刀lathe tool [leɪð] .[tu:l]车床lathe [leɪð]钻削镗削bore [bɔ:]车削turning [ˈtɜ:nɪŋ]磨床grinder [ˈgraɪndə]基准benchmark [ˈbentʃˌmɑ:k]钳工locksmith [ˈlɔkˌsmɪθ]锻forge [fɔ:dʒ]压模stamping [ˈstæmpiŋ]焊weld [weld]拉床broaching machine ['brəutʃiŋ].[məˈʃi:n]拉孔broaching['brəutʃiŋ]装配assembling[ə'sembliŋ]铸造found[faund]流体动力学fluid dynamics['flu(:)id][dai'næmiks]流体力学fluid mechanics ['flu(:)id][mi'kæniks]加工machining [mə'ʃi:niŋ]液压hydraulic pressure[hai'drɔ:lik]['preʃə]切线tangent ['tændʒənt]机电一体化mechanotronics mechanical-electrical integration [,mekənə'trɔniks][mi'kænikl][i'lektrikəl] [,inti'ɡreiʃən]气压air pressure pneumatic pressure ['preʃə][nju(:)'mætik]['preʃə]稳定性stability [stə'biliti]介质medium ['mi:djəm]液压驱动泵fluid clutch ['flu(:)id][klʌtʃ]液压泵hydraulic pump [hai'drɔ:lik][pʌmp]阀门valve [vælv]失效invalidation[in'vælideiʃn]强度intensity [in'tensiti]载荷load [ləud]应力stress [stres]安全系数safety factor ['seifti]['fæktə]可靠性reliability [ri,laiə'biliti]螺纹thread [θred]螺旋helix ['hi:liks]键spline [splain]销pin [pin]滚动轴承rolling bearing ['rəuliŋ]['bɛəriŋ]滑动轴承sliding bearing ['slaidiŋ]['bɛəriŋ]弹簧spring [spriŋ]制动器arrester brake [ə'restə][breik]十字结联轴节crosshead ['krɔshed]联轴器coupling ['kʌpliŋ]链chain [tʃein]皮带strap [stræp]精加工finish machining ['finiʃ][mə'ʃi:niŋ]粗加工rough machining [rʌf][mə'ʃi:niŋ]变速箱体gearbox casing ['ɡiəbɔks]['keisiŋ]腐蚀rust [rʌst]氧化oxidation [ɔksi'deiʃən]磨损wear [wɛə]耐用度durability [,djuərə'biliti]随机信号random signal ['rændəm]['siɡnl]离散信号discrete signal [dis'kri:t] ['siɡnl]超声传感器ultrasonic sensor ['ʌltrə'sɔnik]['sensə]集成电路integrate circuit ['intiɡreit]['sə:kit]挡板orifice plate ['ɔrifis][pleit]残余应力residual stress [ri'zidjuəl][stres]套筒sleeve [sli:v]扭力torsion ['tɔ:ʃən]冷加工cold machining [mə'ʃi:niŋ]电动机electromotor [i,lektrəu'məutə]汽缸cylinder ['silində]过盈配合interference fit [,intə'fiərəns][fit]热加工hot work[hɔt] [wə:k]摄像头CCD camera ['kæmərə]倒角rounding chamfer ['raundiŋ]['tʃæmfə]优化设计optimal design ['ɔptiməl][di'zain]工业造型设计industrial moulding design [in'dʌstriəl] ['məuldiŋ][di'zain]有限元finite element ['fainait]['elimənt]滚齿hobbing ['hɔbiŋ]插齿gear shaping [ɡiə]['ʃeipiŋ]伺服电机actuating motor ['æktjueitiŋ]['məutə]铣床milling machine ['miliŋ][mə'ʃi:n]钻床drill machine [dril] [mə'ʃi:n]镗床boring machine ['bɔ:riŋ] [mə'ʃi:n]步进电机stepper motor ['stepə]['məutə]丝杠screw rod [skru:][rɔd]导轨lead rail [li:d][reil]组件subassembly ['sʌbə'sembli]可编程序逻辑控制器Programmable Logic Controller PLC ['prəuɡræməbl] ['lɔdʒik][kən'trəulə]电火花加工electric spark machining [i'lektrik][spɑ:k] [mə'ʃi:niŋ]电火花线切割加工electrical discharge wire – cutting [i'lektrikəl][dis'tʃɑ:dʒ]相图phase diagram [feiz]['daiəɡræm]固态相变solid state phase changes [feiz]有色金属nonferrous metal ['nɔn'ferəs]['metl]陶瓷ceramics [si'ræmiks]合成纤维synthetic fibre [sin'θetic]['faibə]电化学腐蚀electrochemical corrosion[i,lektrəu'kemikəl] [kə'rəuʒən]车架automotive chassis [ɔ:tə'məutiv] ['ʃæsi]悬架suspension [səs'penʃən]转向器redirector ['ri:di'rektə]变速器speed changer [spi:d]['tʃeindʒə]板料冲压sheet metal parts [ʃi:t]['metl][pɑ:ts]孔加工spot facing machining [spɔt] ['feisiŋ] [mə'ʃi:niŋ]车间workshop ['wə:kʃɔp]工程技术人员engineer [,endʒi'niə]气动夹紧pneuma lock ['nju:mə][lɔk]数学模型mathematical model [,mæθi'mætikəl]画法几何descriptive geometry [dis'kriptiv][dʒi'ɔmitri]机械制图Mechanical drawing [mi'kænikl] ['drɔ:iŋ] 投影projection [prə'dʒekʃən]视图view [vju:]剖视图profile chart ['prəufail][tʃɑ:t]标准件standard component ['stændəd][kəm'pəunənt]零件图part drawing [pɑ:t] ['drɔ:iŋ]装配图assembly drawing [ə'sembli] ['drɔ:iŋ]尺寸标注size marking [saiz]['mɑ:kiŋ]技术要求technical requirements刚度rigidity [ri'dʒiditi]内力internal force [in'tə:nl][fɔ:s]位移displacement [dis'pleismənt]截面section ['sekʃən]疲劳极限fatigue limit [fə'ti:ɡ]['limit]断裂fracture ['fræktʃə]塑性变形plastic distortion ['plæstik, plɑ:stik][dis'tɔ:ʃən]脆性材料brittleness material ['britl][mə'tiəriəl]刚度准则rigidity criterion [ri'dʒiditi] [krai'tiəriən]垫圈washer ['wɔʃə]垫片spacer ['speisə]直齿圆柱齿轮straight toothed spur gear [streit] [tu:θt, tu:ðd][spə:][ɡiə]斜齿圆柱齿轮helical-spur gear ['helikəl] [spə:][ɡiə] 直齿锥齿轮straight bevel gear [streit] ['bevəl] [ɡiə] 运动简图kinematic sketch [,kaini'mætik][sketʃ]齿轮齿条pinion and rack ['pinjən][ræk]蜗杆蜗轮worm and worm gear [wə:m] [ɡiə]虚约束passive constraint ['pæsiv][kən'streint]曲柄crank [kræŋk]摇杆racker ['rækə]凸轮cams [kæm]共轭曲线conjugate curve ['kɔndʒuɡit][kə:v]范成法generation method [,dʒenə'reiʃən]['meθəd]定义域definitional domain [,defi'niʃən][dəu'mein]值域range [reindʒ]导数\\微分differential coefficient [,difə'renʃəl][kəui'fiʃənt]求导derivation [deri'veiʃən]定积分definite integral ['definit]['intiɡrəl]不定积分indefinite integral [in'definit]['intiɡrəl]曲率curvature ['kə:vətʃə]偏微分partial differential ['pɑ:ʃəl][,difə'renʃəl]毛坯rough [rʌf]游标卡尺slide caliper [slaid]['kælipə]千分尺micrometer calipers [mai'krɔmitə] ['kælipəs] 攻丝tap [tæp]二阶行列式second order determinant ['sekənd]['ɔ:də][di'tə:minənt]逆矩阵inverse matrix ['in'və:s]['meitriks]线性方程组linear equations ['liniə][i'kweiʃən]概率probability [,prɔbə'biliti]随机变量random variable ['rændəm]['vɛəriəbl]排列组合permutation and combination[,pə:mju(:)'teiʃən][,kɔmbi'neiʃən]气体状态方程equation of state of gas [i'kweiʃən] [steit][ɡæs]动能kinetic energy [kai'netik]['enədʒi]势能potential energy [pə'tenʃəl]['enədʒi]机械能守恒conservation of mechanical energy [,kɔnsə(:)'veiʃən][mi'kænikl]['enədʒi]动量momentum [məu'mentəm]桁架truss [trʌs]轴线axes ['æksi:z]余子式cofactor [kəu'fæktə]逻辑电路logic circuit ['lɔdʒik]['sə:kit]触发器flip-flop ['flipflɔp]脉冲波形pulse shape [pʌls][ʃeip]数模digital analogy ['didʒitl][ə'nælədʒi]液压传动机构fluid drive mechanism ['flu(:)id] [draiv] ['mekənizəm]机械零件mechanical parts [mi'kænikl][pɑ:t]淬火冷却quench [kwentʃ]淬火hardening ['hɑ:dəniŋ]回火tempering ['tempəriŋ]调质hardening and tempering ['hɑ:dəniŋ]['tempəriŋ]磨粒abrasive grain [ə'breisiv][ɡrein]结合剂bonding agent ['bɔndiŋ]['eidʒənt]砂轮grinding wheel ['ɡraindiŋ][wi:l, hw-]机械零件mechanical parts [mi'kænikl][pɑ:t]淬火冷却quench [kwentʃ]淬火hardening ['hɑ:dəniŋ]回火tempering ['tempəriŋ]调质hardening and tempering ['hɑ:dəniŋ]['tempəriŋ]磨粒abrasive grain [ə'breisiv][ɡrein]结合剂bonding agent ['bɔndiŋ]['eidʒənt]砂轮grinding wheel ['ɡraindiŋ][wi:l, hw-]机床行业部分英汉对照（1)：按英文字母排序3-Jaws indexing spacers [dʒɔ:]['indeksiŋ]['speisə]三爪、分割工具头A T C system ['sɪstəm]加工中心机刀库Aluminum continuous melting & holding furnaces[ə'lu:mənəm][kən'tinjuəs]['meltiŋ]['həuldiŋ]['fə:nis]连续溶解保温炉Balancing equipment ['bælənsiŋ] [i'kwipmənt]平衡设备Bayonet ['beɪənɪt, -,net, ,beɪə'net]卡口Bearing fittings ['bɛəriŋ]['fitiŋ]轴承配件Bearing processing equipment ['bɛəriŋ][prəu'sesiŋ] [i'kwipmənt]轴承加工机Bearings ['bɛəriŋ]轴承Belt drive [belt][draɪv]带传动Bending machines ['bendiŋ][mə'ʃi:n]弯曲机Blades [bleid]刀片Blades,saw [bleid][sɔ:]锯片Bolts,screws & nuts [bəult] [skru:] [nʌts]螺栓,螺帽及螺丝Boring heads ['bɔ:riŋ][hed]搪孔头Boring machines ['bɔ:riŋ][mə'ʃi:n]镗床Cable making tools ['keibl]['meikiŋ][tu:l]造线机Casting,aluminium ['kæstɪŋ] [,ælju:'minjəm]铸铝Casting,copper ['kæstɪŋ]['kɔpə]铸铜Casting,gray iron ['kæstɪŋ][ɡrei]['aiən]铸灰口铁Casting,malleable iron ['kæstɪŋ]['mæliəbl] ['aiən]可锻铸铁Casting,other ['kæstɪŋ]其他铸造Casting,steel ['kæstɪŋ][sti:l]铸钢Chain drive [tʃein] [draɪv]链传动Chain making tools [tʃein]造链机Chamfer machines ['tʃæmfə][mə'ʃi:n]倒角机Chucks [tʃʌk]夹盘Clamping/holding systems ['klæmpiŋ]['həuldiŋ] ['sɪstəm]夹具/支持系统CNC bending presses 电脑数控弯折机（CNC=Computerized Numerical Control[kəm'pju:tə][nju(:)'merikəl][kən'trol]）['bendiŋ] [pres]CNC boring machines ['bɔ:riŋ] [mə'ʃi:n]电脑数控镗床CNC drilling machines ['driliŋ] [mə'ʃi:n]电脑数控钻床CNC EDM wire-cutting machines （EDM=Electron Discharge Machining [i'lektrɔn][dis'tʃɑ:dʒ][mə'ʃi:niŋ]放电加工）[mə'ʃi:n]['waiə]电脑数控电火花线切削机CNC electric discharge machines [i'lektrik][dis'tʃɑ:dʒ] [mə'ʃi:n]电脑数控电火花机CNC engraving machines [en'greɪvɪŋ] [mə'ʃi:n]电脑数控雕刻机CNC grinding machines ['ɡraindiŋ] [mə'ʃi:n]电脑数控磨床CNC lathes [leið]电脑数控车床CNC machine tool fittings [mə'ʃi:n][tu:l]['fitiŋ]电脑数控机床配件CNC milling machines ['miliŋ] [mə'ʃi:n]电脑数控铣床CNC shearing machines ['ʃiəriŋ] [mə'ʃi:n]电脑数控剪切机CNC toolings CNC ['tu:liŋ]刀杆CNC wire-cutting machines ['waiə] ['kʌtiŋ] [mə'ʃi:n]电脑数控线切削机Conveying chains [kən'veiiŋ][tʃein]输送链Coolers ['ku:lə]冷却机Coupling ['kʌpliŋ]联轴器Crimping tools [krimpiŋ] [tu:l]卷边工具Cutters ['kʌtə]刀具Cutting-off machines ['kʌtiŋ] [mə'ʃi:n]切断机Diamond cutters ['daiəmənd]['kʌtə]钻石刀具Dicing saws ['daisiŋ][sɔ:]晶圆切割机Die casting dies [dai]['kɑ:stiŋ]压铸冲模Die casting machines [dai]['kɑ:stiŋ] [mə'ʃi:n]压铸机Dies-progressive [dai][prə'ɡresiv]连续冲模Disposable toolholder bits [dis'pəuzəbl]['tu:l,həuldə][bit]舍弃式刀头Drawing machines ['drɔ:iŋ] [mə'ʃi:n]拔丝机Drilling machines ['driliŋ] [mə'ʃi:n]钻床Drilling machines bench ['driliŋ] [mə'ʃi:n][bentʃ]钻床工作台Drilling machines,high-speed ['driliŋ] [mə'ʃi:n] [hai] [spi:d]高速钻床Drilling machines,multispindle ['driliŋ] [mə'ʃi:n][,m ʌlti] ['spindl]多轴钻床Drilling machines,radial ['driliŋ] [mə'ʃi:n]['reidjəl]摇臂钻床Drilling machines,vertical ['driliŋ] [mə'ʃi:n]['və:tikəl]立式钻床drills [dril]钻头Electric discharge machines(EDM) [i'lektrik][dis'tʃɑ:dʒ] [mə'ʃi:n]电火花机Electric power tools [i'lektrik]['pauə][tu:l]电动刀具Engraving machines [en'greɪvɪŋ] [mə'ʃi:n]雕刻机Engraving machines,laser [en'greɪvɪŋ] [mə'ʃi:n] ['leizə]激光雕刻机Etching machines ['etʃiŋ] [mə'ʃi:n]蚀刻机Finishing machines ['finiʃiŋ] [mə'ʃi:n]修整机Fixture ['fikstʃə]夹具Forging dies ['fɔ:dʒiŋ] [dai]锻模Forging,aluminium ['fɔ:dʒiŋ] [,ælju:'minjəm]锻铝Forging,cold ['fɔ:dʒiŋ][kəuld]冷锻Forging,copper ['fɔ:dʒiŋ]['kɔpə]铜锻Forging,other ['fɔ:dʒiŋ]['ʌðə]其他锻造Forging,steel ['fɔ:dʒiŋ][sti:l]钢锻Foundry equipment ['faundri] [i'kwipmənt]铸造设备Gear cutting machines [ɡiə]['kʌtiŋ] [mə'ʃi:n]齿轮切削机Gears [ɡiə]齿轮Gravity casting machines ['ɡræviti]['kɑ:stiŋ] [mə'ʃi:n]重力铸造机Grinder bench ['ɡraində][bentʃ]磨床工作台Grinders,thread ['ɡraində][θred]螺纹磨床Grinders,tools & cutters ['ɡraində][tu:l]['kʌtə]工具磨床Grinders,ultrasonic ['ɡraində]['ʌltrə'sɔnik]超声波打磨机Grinding machines ['ɡraindiŋ] [mə'ʃi:n]磨床Grinding machines,centerless ['ɡraindiŋ] [mə'ʃi:n] ['sentəles]无心磨床Grinding machines,cylindrical ['ɡraindiŋ] [mə'ʃi:n] [si'lindrik(ə)l]外圆磨床Grinding machines,universal ['ɡraindiŋ] [mə'ʃi:n] [,ju:ni'və:səl]万能磨床Grinding tools ['ɡraindiŋ][tu:l]磨削工具Grinding wheels ['ɡraindiŋ][wi:l, hw-]磨轮Hand tools [hænd][tu:l]手工具Hard/soft and free expansion sheet makingplant [hɑ:d] [iks'pænʃən] [ʃi:t]硬(软)板(片)材及自由发泡板机组Heat preserving furnaces [pri'zə:v]['fə:nis]保温炉Heating treatment funaces ['tri:tmənt] ['fə:nis]熔热处理炉Honing machines ['həuniŋ] [mə'ʃi:n]搪磨机Hydraulic components [hai'drɔ:lik][kəm'pəunənt]液压元件Hydraulic power tools [hai'drɔ:lik]液压工具Hydraulic power units [hai'drɔ:lik]液压动力元件Hydraulic rotary cylinders [hai'drɔ:lik]['rəutəri]['silində]液压回转缸Jigs [dʒiɡ]钻模Lapping machines ['læpiŋ] [mə'ʃi:n]精研机Lapping machines,centerless ['læpiŋ] [mə'ʃi:n]无心精研机Laser cutting ['leizə]['kʌtiŋ]激光切割Laser cutting for SMT stencil ['leizə]['kʌtiŋ]['stensl, -sil]激光钢板切割机Lathe bench ['leizə][bentʃ]车床工作台Lathes,automatic ['leizə] [,ɔ:tə'mætik]自动车床Lathes,heavy-duty ['leizə][hevi:'du:ti:, -'dju:-]重型车床Lathes,high-speed ['leizə] [hai][spi:d]高速车床Lathes,turret ['leizə]['tʌrit]六角车床Lathes,vertical ['leizə]['və:tikəl]立式车床Lubricants ['lu:brikənt]润滑液Lubrication Systems [,lu:bri'keiʃən] ['sɪstəm]润滑系统Lubricators ['lju:brikeitə]注油机Machining centers,general [mə'ʃi:niŋ]['sentə]['dʒenərəl]通用加工中心Machining centers,horizontal [mə'ʃi:niŋ]['sentə][,h ɔri'zɔntl]卧式加工中心Machining centers,horizontal & vertical [mə'ʃi:niŋ] ['sentə] [,hɔri'zɔntl] ['və:tikəl]卧式及立式加工中心Machining centers,vertical [mə'ʃi:niŋ]['sentə]['və:tikəl]立式加工中心Machining centers,vertical double-column type [mə'ʃi:niŋ]['sentə]['və:tikəl]['dʌbl]['kɔləm][taip]立式双柱加工中心Magnetic tools [mæɡ'netik][tu:l]磁性工具Manifolds ['mænifəuld]集合管Milling heads ['miliŋ][hed]铣头Milling machines ['miliŋ][mə'ʃi:n]铣床Milling machines,bed type ['miliŋ][mə'ʃi:n] [taip]床身式铣床Milling machines,duplicating ['miliŋ][mə'ʃi:n]['dju:plikeitiŋ]仿形铣床Milling machines,horizontal ['miliŋ][mə'ʃi:n][,hɔri'z ɔntl]卧式铣床Milling machines,turret vertical ['miliŋ][mə'ʃi:n]['tʌrit]['və:tikəl]六角立式铣床Milling machines,universal ['miliŋ][mə'ʃi:n][,ju:ni'və:səl]万能铣床Milling machines,vertical ['miliŋ][mə'ʃi:n]['və:tikəl]立式铣床Milling machines,vertical & horizontal ['miliŋ][mə'ʃi:n]['və:tikəl] [,hɔri'zɔntl]立式及卧式铣床Mold & die components [məuld][dai][kəm'pəunənt]模具单元Mold changing systems [məuld]['tʃeindʒiŋ]['sɪstəm]换模系统Mold core [məuld][kɔ:]模芯Mold heaters/chillers [məuld]['hi:tə]['tʃilə]模具加热器/冷却器Mold polishing/texturing [məuld]['pɔliʃiŋ]['tekstʃər iŋ]模具打磨/磨纹Mold repair [məuld][ri'pɛə]模具维修Molds [məuld]模具Nail making machines [neil][mə'ʃi:n]造钉机Oil coolers [ɔil]['ku:lə]油冷却器Overflow cutting machines for aluminium wheels ['əuvə'fləu] [mə'ʃi:n][,ælju:'minjəm][wi:l, hw-]铝轮冒口切断机P type PVC waterproof rolled sheet making plant[taip] ['wɔ:təpru:f][rəuld][ʃi:t] [plɑ:nt] P型PVC 高分子防水PCB fine piecing systems [fain][pi:s]['sɪstəm]( PCB =Printed -circuit Board [bɔ:d]印刷电路板)印刷电器板油压冲孔脱料系统Pipe & tube making machines [paip] [mə'ʃi:n]['tju:b] [mə'ʃi:n]管筒制造机Planing machines [plæniŋ] [mə'ʃi:n]刨床Planing machines vertical [plæniŋ] [mə'ʃi:n]['və:tikəl]立式刨床Pneumatic hydraulic clamps [nju(:)'mætik][hai'dr ɔ:lik][klæmp]气油压虎钳Pneumatic power tools [nju(:)'mætik]['pauə][tu:l]气动工具Powder metallurgic forming machines ['paudə][,metə'lə:dʒik]['fɔ:miŋ] [mə'ʃi:n]粉末冶金成型机Presses,cold forging [pres]['fɔ:dʒiŋ]冷锻冲压机presses,crank [pres][kræŋk]曲柄压力机Presses,eccentric [pres][ik'sentrik]离心压力机Presses,forging [pres]['fɔ:dʒiŋ]锻压机Presses,hydraulic [pres]液压冲床Presses,knuckle joint [pres]肘杆式压力机Presses,pneumatic [pres][hai'drɔ:lik]气动冲床Presses,servo [pres]['sə:vəu]伺服冲床Presses,transfer [pres][træns'fə:]自动压力机Pressing dies [presiŋ]['daii:z]压模Punch formers [pʌntʃ]['fɔ:mə]冲子研磨器Quick die change systems [kwik][dai][tʃeindʒ]['sɪstəm]速换模系统Quick mold change systems [kwik][məuld][tʃeindʒ] ['sɪstəm]快速换模系统Reverberatory furnaces [ri'və:bərətəri]['fə:nis]反射炉Rollers ['rəulə]滚筒Rolling machines ['rəuliŋ] [mə'ʃi:n]辗压机Rotary tables ['rəutəri]['teibl]转台Sawing machines ['sɔ:iŋ] [mə'ʃi:n]锯床Sawing machines,band ['sɔ:iŋ] [mə'ʃi:n][bænd]带锯床Saws,band [sɔ:][bænd]带锯Saws,hack [sɔ:][hæk]弓锯Saws,horizontal band [sɔ:][,hɔri'zɔntl] [bænd]卧式带锯Saws,vertical band [sɔ:] ['və:tikəl] [bænd]立式带锯shafts [ʃɑ:ft]轴Shapers ['ʃeipə]牛头刨床Shearing machines ['ʃiəriŋ] [mə'ʃi:n]剪切机Sheet metal forming machines [ʃi:t] ['metl] ['fɔ:miŋ] [mə'ʃi:n]金属板成型机Sheet metal working machines [ʃi:t] ['metl] [mə'ʃi:n]金属板加工机Slotting machines ['slɔtiŋ] [mə'ʃi:n]插床spindles ['spindl]主轴Stamping parts ['stæmpiŋ][pɑ:t]冲压机Straightening machines ['streitniŋ] [mə'ʃi:n]矫直机Switches & buttons [switʃ]['bʌtn]开关及按钮Tapping machines ['tæpiŋ] [mə'ʃi:n]攻螺丝机Transmitted chains [trænz'mit][tʃein]传动链Tube bending machines ['tju:b] ['bendiŋ] [mə'ʃi:n]弯管机Vertical hydraulic broaching machine ['və:tikəl] [hai'drɔ:lik] ['brəutʃiŋ] [mə'ʃi:n]立式油压拉床Vises [vais]虎钳Vises,tool-maker [vais]['tu:l,meɪkə]精密平口钳Wheel dressers [wi:l, hw-]['dresə]砂轮修整器Woven-Cutting machines ['wəuvən] ['kʌtiŋ] [mə'ʃi:n]织麦激光切割机Wrenches [rentʃ]扳手螺丝词汇的中英文对照六角盖头螺帽HEX CAP NUTS (HEX= hexagon['heksəɡən] 六角形; 六边形)[kæp][nʌts]六角锯齿螺帽HEX SERRATED NUTS (HEX= hexagon ['heksəɡən] 六角形; 六边形)[se'reitid[nʌts]六角轮缘螺帽HEX FLANGE NUTS (HEX= hexagon ['heksəɡən] 六角形; 六边形)[flændʒ] [nʌts]高脚螺帽HEX COUPLING NUTS(HIGH NUTS) (HEX= hexagon ['heksəɡən] 六角形; 六边形)['kʌpliŋ][nʌts] [hai]圆螺帽ROUND NUTS [raund][nʌts]四角螺帽SQUARE NUTS HEAVY HEX NUTS [skwɛə] [n ʌts] ['hevi] (HEX= hexagon ['heksəɡən] 六角形; 六边形)不锈钢六角螺帽STAINLESS STEEL HEX NUTS ['steinlis] [sti:l] (HEX= hexagon ['heksəɡən] 六角形; 六边形)[n ʌts]不锈钢尼龙嵌入螺帽STAINLESS STEEL NYLON INSERT LOCK NUTS ['steinlis][sti:l]['nailən][in'sə:t] [lɔk] [nʌts]普通六角螺帽HEX NUTS (HEX= hexagon['heksəɡən] 六角形; 六边形)[nʌts]六角重型螺帽HEAVY HEX NUTS ['hevi] (HEX= hexagon ['heksəɡən] 六角形; 六边形)[nʌts]薄型螺帽HEX JAM NUTS (HEX= hexagon['heksəɡən] 六角形; 六边形)[dʒæm] [nʌts]尼龙嵌入防松螺帽NYLON INSERT LOCK NUTS['nailən] [in'sə:t][lɔk] [nʌts]机械螺丝用六角螺帽HEX MACHINE SCREW NUT (HEX= hexagon ['heksəɡən] 六角形; 六边形)[mə'ʃi:n][skru:] [nʌt]机械工具英语机械工具spanner 扳子(美作:wrench) ['spænə][rent ʃ]double-ended spanner ['spænə]双头扳子adjustable spanner, monkey wrench [ə'dʒʌstəbl] ['spænə]['mʌŋki] [rentʃ]活扳子,活络扳手box spanner 管钳子(美作:socket wrench) [bɔks] ['spænə]['sɔkit] [rentʃ]calipers ['kælipə]卡规pincers, tongs ['pinsəz][tɔŋz]夹钳shears [ʃiəz]剪子hacksaw ['hæksɔ:]钢锯wire cutters ['waiə]['kʌtə]剪线钳multipurpose pliers,universal pliers ['mʌlti'pə:pəs] ['plaiə][,ju:ni'və:səl]['plaiəz]万能手钳adjustable pliers [ə'dʒʌstəbl] ['plaiəz]可调手钳punch [pʌntʃ]冲子drill [dril]钻chuck [tʃʌk]卡盘scraper ['skreipə]三角刮刀reamer ['ri:mə]扩孔钻calliper gauge ['kælipə][ɡedʒ]孔径规rivet ['rivit]铆钉nut [nʌt]螺母locknut ['lɔknʌt]自锁螺母,防松螺母bolt [bəult]螺栓pin, peg, dowel [pin][peɡ]['dauəl]销钉washer ['wɔʃə]垫圈staple ['steipl]U形钉oil can 油壶jack工作服grease gun [ɡri:s]注油枪机械加工抛光polishing ['pɔliʃiŋ]安装to assemble [ə'sembl]衬套bushing ['buʃiŋ]外贸常用机械英语大全Assembly line [ə'sembl]组装线Layout ['lei,aut]布置图Conveyer [kən'vei]流水线物料板Rivet table ['rivit]拉钉机Rivet gun ['rivit]拉钉枪Screw driver 起子Pneumatic screw driver [nju(:)'mætik]气动起子worktable ['wə:kteibl]工作桌OOBA 开箱检查fit together [tə'ɡeðə]组装在一起fasten ['fɑ:sn]锁紧(螺丝)fixture ['fikstʃə]夹具(治具) pallet ['pælit]栈板bar code [bɑ:][kəud]条码bar code scanner [bɑ:][kəud]['skænə]条码扫描器fuse together [fju:z][tə'ɡeðə]熔合fuse machine[fju:z] [mə'ʃi:n]热熔机repair[ri'pɛə]修理operator['ɔpəreitə]作业员QC [=Quality Control ['kwɔliti][kən'trol]质量控制]品管supervisor ['sju:pəvaizə]课长ME [=Mechanical Engineer 机械工程师]制造工程师MT 制造生技cosmetic inspect [kɔz'metik][in'spekt]外观检查inner parts inspect ['inə][in'spekt]内部检查thumb screw [θʌm]大头螺丝lbs inch [intʃ]镑、英寸EMI gasket ['ɡæskit]导电条front plate [frʌnt][pleit]前板rear plate [riə] [pleit]后板chassis ['ʃæsi]基座bezel panel ['bezəl]['pænl]面板power button ['pauə] ['bʌtn]电源按键reset button ['ri:set] ['bʌtn]重置键Hi-pot test of SPS [test]高源高压测试Voltage switch of SPS ['vəultidʒ][switʃ]电源电压接拉键sheet metal parts [ʃi:t]冲件plastic parts ['plæstik, plɑ:stik]塑胶件SOP [=Standard Operating Procedure 标准操作程序]制造作业程序material check list [mə'tiəriəl]物料检查表work cell [wə:k] [sel]工作间trolley ['trɔli]台车carton ['kɑ:tən]纸箱sub-line ['sʌblain]支线left fork [fɔ:k]叉车personnel resource department [,pə:sə'nel] [ri'sɔ:s] [di'pɑ:tmənt]人力资源部production department[prə'dʌkʃən]生产部门planning department['plænɪŋ][di'pɑ:tmənt]企划部QC Section ['sekʃən]品管科stamping factory['stæmpiŋ]['fæktəri]冲压厂painting factory['peintiŋ]烤漆厂molding factory['məuldiŋ]['fæktəri]成型厂common equipment['kɔmən][i'kwipmənt]常用设备uncoiler and straightener[ʌn'kɔilə]['streitənə]整平机punching machine [pʌntʃiŋ][mə'ʃi:n]冲床robot['rəubɔt, 'rɔbət]机械手hydraulic machine[hai'drɔ:lik]油压机lathe[leið]车床planer |plein|刨床miller ['milə]铣床grinder['ɡraində]磨床linear cutting['liniə]['kʌtiŋ]线切割electrical sparkle[i'lektrikəl]['spɑ:kl]电火花welder['weldə]电焊机staker=reviting machine['steikə]铆合机position [pə'ziʃən职务president ['prezidənt]董事长general manager['dʒenərəl]['mænidʒə]总经理special assistant manager['speʃəl][ə'sɪstənt]['mænidʒə]特助factory director ['fæktəri] [di'rektə, dai'rektə]厂长department director[di'pɑ:tmənt] [di'rektə, dai'rektə]部长deputy manager | =vice manager 副理section supervisor课长['depjuti] ['mænidʒə] ['sju:pəvaizə] deputy section supervisor =vice section superisor['depjuti]['sekʃən] ['sju:pəvaizə]副课长group leader/supervisor['sju:pəvaizə]组长line supervisor['sju:pəvaizə]线长assistant manager助理to move, to carry, to handle['hændl]搬运be put in storage['stɔridʒ]入库pack packing包装to apply oil [ə'plai]擦油to file burr [fail][bə:]锉毛刺final inspection['fainəl][in'spekʃən]终检to connect material[kə'nekt][mə'tiəriəl]接料to reverse material [ri'və:s] [mə'tiəriəl]翻料wet station['steiʃən]沾湿台Tiana天那水cleaning cloth['kli:niŋ][klɔ(:)θ]抹布to load material[ləud] [mə'tiəriəl]上料to unload material['ʌn'ləud] [mə'tiəriəl]卸料to return material/stock to [ri'tə:n] [mə'tiəriəl] [stɔk]退料scraped [skreipid]报废scrape [skreip]v 刮;削deficient purchase[di'fiʃənt] ['pə:tʃəs]来料不良manufacture procedure[,mænju'fæktʃə] [prə'si:dʒə]制程deficient manufacturing procedure[di'fiʃənt][,mænju'fæktʃə] [prə'si:dʒə]制程不良oxidation [ɔksi'deiʃən]氧化scratch[skrætʃ]刮伤dents['dents]压痕defective upsiding down[di'fektiv] ['ʌpsaidiŋ]抽芽不良defective to staking[di'fektiv] ['steikiŋ]铆合不良embedded lump[em'bedid] [lʌmp]镶块feeding is not in place['fi:diŋ] [pleis]送料不到位stamping-missing ['stæmpiŋ] ['misiŋ]漏冲production capacity [prə'dʌkʃən] [kə'pæsiti]生产力education and training [,edju(:)'keiʃən] ['treiniŋ]教育与训练proposal improvement[prə'pəuzəl] [im'pru:vmənt]提案改善spare parts=buffer['bʌfə]备件forklift['fɔ:klift]叉车trailer=long vehicle ['treilə] ['vi:ikl]拖板车外贸常用机械英语大全(续)compound die['kɔmpaund] [dai]合模die locker [dai] ['lɔkə]锁模器pressure plate=plate pinch ['preʃə][pleit] [pintʃ]压板bolt [bəult]螺栓administration/general affairs dept[ədminis'treiʃən] ['dʒenərəl]总务部automatic screwdriver[,ɔ:tə'mætik] ['skru:draivə]电动启子thickness gauge['θiknis][ɡedʒ]厚薄规gauge(or jig)[ɡedʒ]治具power wire['pauə]['waiə]电源线buzzle[bʌzl]蜂鸣器defective product label[di'fektiv]['prɔdʌkt]['leibl]不良标签identifying sheet list [ai'dentifai][ʃi:t]标示单location[ləu'keiʃən]地点present members['preznt]['membə]出席人员subject['sʌbdʒikt]主题conclusion[kən'klu:ʒən]结论decision items[di'siʒən] ['aitem, 'aitəm]决议事项responsible department[ris'pɔnsəbl] [di'pɑ:tmənt]负责单位prefixed finishing date['pri:fiks] ['finiʃiŋ] [deit]预定完成日approved by / checked by / prepared by[ə'pru:vd] [pri'pɛəd核准/审核/承办PCE assembly production schedule sheet PCE[ə'sembli] [prə'dʌkʃən] ['ʃedju:l; 'skedʒjul] [ʃi:t]组装厂生产排配表model ['mɔdl]机锺work order[wə:k]工令revision[ri'viʒən]版次。
复试机械专业英语词汇
复试机械专业英语词汇必知金属切削metal cutting 机床machine tool金属工艺学technology of metals刀具cutter电路circuit半导体元件semiconductor element反馈feedback发生器generator直流电源DC electrical source门电路gate circuit逻辑代数logic algebra逻辑电路logic circuit触发器flip-flop脉冲波形pulse shape数模digital analogy液压传动机构fluid drive mechanism 机械零件mechanical parts摩擦friction联结link传动drive/transmission轴shaft弹性elasticity频率特性frequency characteristic误差error响应response定位allocation 机床夹具jig动力学dynamic运动学kinematic静力学static分析力学analyse mechanics拉伸pulling压缩hitting剪切shear扭转twist弯曲应力bending stress强度intensity三相交流电three-phase AC磁路magnetic circles 变压器transformer异步电动机asynchronous motor几何形状geometrical精度precision正弦形的sinusoid交流电路AC circuit机械加工余量machining allowance变形力deforming force变形deformation应力stress硬度rigidity热处理heat treatment退火anneal正火normalizing脱碳decarburization渗碳carburization淬火冷却quench淬火hardening回火tempering调质hardening and tempering磨粒abrasive grain结合剂bonding agent砂轮grinding wheel外圆磨削external grinding内圆磨削internal grinding平面磨削plane grinding变速箱gearbox离合器clutch绞孔fraising绞刀reamer螺纹加工thread processing螺钉screw铣削mill铣刀milling cutter功率power工件workpiece齿轮加工gear mechining齿轮gear主运动main movement主运动方向direction of main movement进给方向direction of feed进给运动feed movement合成进给运动resultant movement of feed合成切削运动resultant movement of cutting合成切削运动方向direction of resultant movement of cutting切削深度cutting depth前刀面rake face刀尖nose of tool前角rake angle后角clearance angle龙门刨削planing主轴spindle主轴箱headstock卡盘chuck加工中心machining center车刀lathe tool车床lathe钻削镗削bore车削turning磨床grinder基准benchmark钳工locksmith锻forge压模stamping焊weld拉床broaching machine拉孔broaching装配assembling铸造found流体动力学fluid dynamics流体力学fluid mechanics加工machining液压hydraulic pressure切线tangent机电一体化mechanotronics mechanical-electrical integration气压air pressure pneumatic pressure稳定性stability 介质medium液压驱动泵fluid clutch液压泵hydraulic pump阀门valve失效invalidation强度intensity载荷load应力stress安全系数safty factor可靠性reliability螺纹thread螺旋helix键spline销pin滚动轴承rolling bearing滑动轴承sliding bearing弹簧spring 制动器arrester brake十字结联轴节crosshead联轴器coupling链chain皮带strap精加工finish machining粗加工rough machining变速箱体gearbox casing腐蚀rust氧化oxidation磨损wear耐用度durability随机信号random signal离散信号discrete signal超声传感器ultrasonic sensor集成电路integrate circuit 挡板orifice plate金属切削metal cutting机床machine tool 金属工艺学technology of metals刀具cutter摩擦friction联结link传动drive/transmission轴shaft弹性elasticity频率特性frequency characteristic误差error响应response定位allocation机床夹具jig动力学dynamic运动学kinematic 静力学static分析力学analyse mechanics 拉伸pulling压缩hitting剪切shear扭转twist弯曲应力bending stress强度intensity三相交流电three-phase AC磁路magnetic circles变压器transformer异步电动机asynchronous motor几何形状geometrical精度precision正弦形的sinusoid交流电路AC circuit 机械加工余量machining allowance 变形力deforming force变形deformation应力stress 硬度rigidity热处理heat treatment退火anneal正火normalizing 脱碳decarburization渗碳carburization 电路circuit半导体元件semiconductor element反馈feedback发生器generator 直流电源DC electrical source门电路gate circuit 逻辑代数logic algebra外圆磨削external grinding内圆磨削internal grinding面磨削plane grinding变速箱gearbox离合器clutch 绞孔fraising绞刀reamer 螺纹加工thread processing螺钉screw 铣削mill铣刀milling cutter 功率power工件workpiece 齿轮加工gear mechining齿轮gear主运动main movement主运动方向direction of main movement 进给方向direction of feed 进给运动feed movement 合成进给运动resultant movement of feed 合成切削运动resultant movement of cutting合成切削运动方向direction of resultant movement of cutting切削深度cutting depth前刀面rake face刀尖nose of tool前角rake angle 后角clearance angle龙门刨削planing 主轴spindle主轴箱headstock 卡盘chuck加工中心machining center 车刀lathe tool车床lathe 钻削镗削bore车削turning 磨床grinder基准benchmark 钳工locksmith锻forge 压模stamping焊weld 拉床broaching machine拉孔broaching 装配assembling铸造found 流体动力学fluid dynamics流体力学fluid mechanics 加工machining液压hydraulic pressure 切线tangent气压air pressure pneumatic pressure机电一体化mechanotronics mechanical-electrical integration稳定性stability介质medium 液压驱动泵fluid clutch液压泵hydraulic pump 阀门valve失效invalidation 强度intensity载荷load 应力stress安全系数safty factor 可靠性reliability螺纹thread 螺旋helix键spline 销pin滚动轴承rolling bearing 滑动轴承sliding bearing弹簧spring 制动器arrester brake十字结联轴节crosshead 联轴器coupling链chain 皮带strap精加工finish machining 粗加工rough machining变速箱体gearbox casing 腐蚀rust氧化oxidation 磨损wear耐用度durability 随机信号random signal离散信号discrete signal 超声传感器ultrasonic sensor集成电路integrate circuit 挡板orifice plate残余应力residual stress 套筒sleeve扭力torsion 冷加工cold machining电动机electromotor 汽缸cylinder过盈配合interference fit 热加工hotwork摄像头CCD camera 倒角rounding chamfer优化设计optimal design 工业造型设计industrial moulding design 有限元finite element 滚齿hobbing插齿gear shaping 伺服电机actuating motor铣床milling machine 钻床drill machine镗床boring machine 步进电机stepper motor丝杠screw rod 导轨lead rail组件subassembly可编程序逻辑控制器Programmable Logic Controller PLC电火花加工electric spark machining电火花线切割加工electrical discharge wire - cutting相图phase diagram 热处理heat treatment固态相变solid state phase changes 有色金属nonferrous metal陶瓷ceramics 合成纤维synthetic fibre电化学腐蚀electrochemical corrosion 车架automotive chassis悬架suspension 转向器redirector变速器speed changer 板料冲压sheet metal parts孔加工spot facing machining 车间workshop工程技术人员engineer 气动夹紧pneuma lock数学模型mathematical model 画法几何descriptive geometry机械制图Mechanical drawing 投影projection视图view 剖视图profile chart标准件standard component 零件图part drawing装配图assembly drawing 尺寸标注size marking技术要求technical requirements 刚度rigidity内力internal force 位移displacement截面section 疲劳极限fatigue limit断裂fracture 塑性变形plastic distortion脆性材料brittleness material 刚度准则rigidity criterion垫圈washer 垫片spacer直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear 直齿锥齿轮straight bevel gear 运动简图kinematic sketch齿轮齿条pinion and rack 蜗杆蜗轮worm and worm gear虚约束passive constraint 曲柄crank摇杆racker 凸轮cams共轭曲线conjugate curve 范成法generation method定义域definitional domain 值域range导数\\微分differential coefficient 求导derivation定积分definite integral 不定积分indefinite integral曲率curvature 偏微分partial differential毛坯rough 游标卡尺slide caliper千分尺micrometer calipers 攻丝tap二阶行列式second order determinant 逆矩阵inverse matrix线性方程组linear equations 概率probability随机变量random variable 排列组合permutation and combination气体状态方程equation of state of gas 动能kinetic energy势能potential energy 机械能守恒conservation of mechanical energyn 动量momentum 桁架truss轴线axes 余子式cofactor逻辑电路logic circuit 触发器flip-flop脉冲波形pulse shape 数模digital analogy液压传动机构fluid drive mechanism 机械零件mechanical parts淬火冷却quench 淬火hardening回火tempering 调质hardening and tempering磨粒abrasive grain 结合剂bonding agent砂轮grinding wheel阿基米德蜗杆Archimedes worm 安全系数safety factor; factor of safety安全载荷safe load 凹面、凹度concavity扳手wrench 板簧flat leaf spring半圆键woodruff key 变形deformation摆杆oscillating bar 摆动从动件oscillating follower摆动从动件凸轮机构cam with oscillating follower 摆动导杆机构oscillating guide-bar mechanism摆线齿轮cycloidal gear 摆线齿形cycloidal tooth profile摆线运动规律cycloidal motion 摆线针轮cycloidal-pin wheel包角angle of contact 保持架cage背对背安装back-to-back arrangement 背锥back cone ；normal cone背锥角back angle 背锥距back cone distance比例尺scale 比热容specific heat capacity闭式链closed kinematic chain 闭链机构closed chain mechanism臂部arm 变频器frequency converters变频调速frequency control of motor speed 变速speed change变速齿轮change gear ; change wheel 变位齿轮modified gear变位系数modification coefficient 标准齿轮standard gear标准直齿轮standard spur gear 表面质量系数superficial mass factor表面传热系数surface coefficient of heat transfer 表面粗糙度surface roughness并联式组合combination in parallel 并联机构parallel mechanism并联组合机构parallel combined mechanism 并行工程concurrent engineering并行设计concurred design, CD 不平衡相位phase angle of unbalance不平衡imbalance (or unbalance) 不平衡量amount of unbalance不完全齿轮机构intermittent gearing 波发生器wave generator波数number of waves 补偿compensation参数化设计parameterization design, PD 残余应力residual stress操纵及控制装置operation control device 槽轮Geneva wheel槽轮机构Geneva mechanism ；Maltese cross 槽数Geneva numerate槽凸轮groove cam 侧隙backlash差动轮系differential gear train 差动螺旋机构differential screw mechanism差速器differential 常用机构conventional mechanism; mechanism in common use 车床lathe 承载量系数bearing capacity factor承载能力bearing capacity 成对安装paired mounting尺寸系列dimension series 齿槽tooth space齿槽宽spacewidth 齿侧间隙backlash齿顶高addendum 齿顶圆addendum circle齿根高dedendum 齿根圆dedendum circle齿厚tooth thickness 齿距circular pitch齿宽face width 齿廓tooth profile齿廓曲线tooth curve 齿轮gear齿轮变速箱speed-changing gear boxes 齿轮齿条机构pinion and rack齿轮插刀pinion cutter; pinion-shaped shaper cutter 齿轮滚刀hob ,hobbing cutter 齿轮机构gear 齿轮轮坯blank齿轮传动系pinion unit 齿轮联轴器gear coupling齿条传动rack gear 齿数tooth number齿数比gear ratio 齿条rack齿条插刀rack cutter; rack-shaped shaper cutter 齿形链、无声链silent chain齿形系数form factor 齿式棘轮机构tooth ratchet mechanism插齿机gear shaper 重合点coincident points重合度contact ratio 冲床punch传动比transmission ratio, speed ratio 传动装置gearing; transmission gear传动系统driven system 传动角transmission angle传动轴transmission shaft 串联式组合combination in series串联式组合机构series combined mechanism 串级调速cascade speed control创新innovation ; creation 创新设计creation design垂直载荷、法向载荷normal load 唇形橡胶密封lip rubber seal磁流体轴承magnetic fluid bearing 从动带轮driven pulley从动件driven link, follower 从动件平底宽度width of flat-face从动件停歇follower dwell 从动件运动规律follower motion从动轮driven gear 粗线bold line粗牙螺纹coarse thread 大齿轮gear wheel打包机packer 打滑slipping带传动belt driving 带轮belt pulley带式制动器band brake 单列轴承single row bearing单向推力轴承single-direction thrust bearing 单万向联轴节single universal joint单位矢量unit vector 当量齿轮equivalent spur gear; virtual gear当量齿数equivalent teeth number; virtual number of teeth当量摩擦系数equivalent coefficient of friction当量载荷equivalent load 刀具cutter导数derivative 倒角chamfer导热性conduction of heat 导程lead导程角lead angle 等加等减速运动规律parabolic motion; constant acceleration and deceleration motion等速运动规律uniform motion; constant velocity motion 等径凸轮conjugate yoke radial cam等宽凸轮constant-breadth cam 等效构件equivalent link等效力equivalent force 等效力矩equivalent moment of force等效量equivalent 等效质量equivalent mass等效转动惯量equivalent moment of inertia 等效动力学模型dynamically equivalent model底座chassis 低副lower pair点划线chain dotted line （疲劳）点蚀pitting垫圈gasket 垫片密封gasket seal碟形弹簧belleville spring 动力学dynamics顶隙bottom clearance 定轴轮系ordinary gear train; gear train with fixed axes动密封kinematical seal 动能dynamic energy动力粘度dynamic viscosity 动力润滑dynamic lubrication动平衡dynamic balance 动平衡机dynamic balancing machine动态特性dynamic characteristics 动态分析设计dynamic analysis design动压力dynamic reaction 动载荷dynamic load端面transverse plane 端面参数transverse parameters端面齿距transverse circular pitch 端面齿廓transverse tooth profile端面重合度transverse contact ratio 端面模数transverse module端面压力角transverse pressure angle 锻造forge对称循环应力symmetry circulating stress 对心滚子从动件radial (or in-line ) roller follower对心直动从动件radial (or in-line ) translating follower对心移动从动件radial reciprocating follower对心曲柄滑块机构in-line slider-crank (or crank-slider) mechanism多列轴承multi-row bearing多楔带poly V-belt 多项式运动规律polynomial motion多质量转子rotor with several masses 惰轮idle gear额定寿命rating life 额定载荷load ratingII 级杆组dyad 发生线generating line发生面generating plane 法面normal plane法面参数normal parameters 法面齿距normal circular pitch法面模数normal module 法面压力角normal pressure angle法向齿距normal pitch 法向齿廓normal tooth profile法向直廓蜗杆straight sided normal worm 法向力normal force反馈式组合feedback combining 反向运动学inverse ( or backward) kinematics反转法kinematic inversion 反正切Arctan范成法generating cutting 仿形法form cutting方案设计、概念设计concept design, CD 防振装置shockproof device飞轮flywheel 飞轮矩moment of flywheel非标准齿轮nonstandard gear 非接触式密封non-contact seal非周期性速度波动aperiodic speed fluctuation 非圆齿轮non-circular gear粉末合金powder metallurgy 分度线reference line; standard pitch line分度圆reference circle; standard (cutting) pitch circle分度圆柱导程角lead angle at reference cylinder分度圆柱螺旋角helix angle at reference cylinder 分母denominator分子numerator 分度圆锥reference cone; standard pitch cone分析法analytical method 封闭差动轮系planetary differential复合铰链compound hinge 复合式组合compound combining复合轮系compound (or combined) gear train 复合平带compound flat belt复合应力combined stress 复式螺旋机构Compound screw mechanism复杂机构complex mechanism 杆组Assur group干涉interference 刚度系数stiffness coefficient刚轮rigid circular spline 钢丝软轴wire soft shaft刚体导引机构body guidance mechanism 刚性冲击rigid impulse (shock)刚性转子rigid rotor 刚性轴承rigid bearing刚性联轴器rigid coupling 高度系列height series高速带high speed belt 高副higher pair格拉晓夫定理Grashoff`s law 根切undercutting公称直径nominal diameter 高度系列height series功work 工况系数application factor工艺设计technological design 工作循环图working cycle diagram工作机构operation mechanism 工作载荷external loads工作空间working space 工作应力working stress工作阻力effective resistance 工作阻力矩effective resistance moment公法线common normal line 公共约束general constraint公制齿轮metric gears 功率power功能分析设计function analyses design 共轭齿廓conjugate profiles共轭凸轮conjugate cam 构件link鼓风机blower 固定构件fixed link; frame固体润滑剂solid lubricant 关节型操作器jointed manipulator惯性力inertia force 惯性力矩moment of inertia ,shaking moment惯性力平衡balance of shaking force 惯性力完全平衡full balance of shaking force 惯性力部分平衡partial balance of shaking force 惯性主矩resultant moment of inertia惯性主失resultant vector of inertia 冠轮crown gear广义机构generation mechanism 广义坐标generalized coordinate轨迹生成path generation 轨迹发生器path generator滚刀hob 滚道raceway滚动体rolling element 滚动轴承rolling bearing滚动轴承代号rolling bearing identification code 滚针needle roller滚针轴承needle roller bearing 滚子roller滚子轴承roller bearing 滚子半径radius of roller滚子从动件roller follower 滚子链roller chain滚子链联轴器double roller chain coupling 滚珠丝杆ball screw滚柱式单向超越离合器roller clutch 过度切割undercutting函数发生器function generator 函数生成function generation含油轴承oil bearing 耗油量oil consumption耗油量系数oil consumption factor 赫兹公式H. Hertz equation合成弯矩resultant bending moment 合力resultant force合力矩resultant moment of force 黑箱black box横坐标abscissa 互换性齿轮interchangeable gears花键spline 滑键、导键feather key滑动轴承sliding bearing 滑动率sliding ratio滑块slider 环面蜗杆toroid helicoids worm环形弹簧annular spring 缓冲装置shocks; shock-absorber灰铸铁grey cast iron 回程return回转体平衡balance of rotors 混合轮系compound gear train积分integrate 机电一体化系统设计mechanical-electrical integration system design 机构mechanism 机构分析analysis of mechanism机构平衡balance of mechanism 机构学mechanism机构运动设计kinematic design of mechanism 机构运动简图kinematic sketch of mechanism机构综合synthesis of mechanism 机构组成constitution of mechanism机架frame, fixed link 机架变换kinematic inversion机器machine 机器人robot机器人操作器manipulator 机器人学robotics技术过程technique process 技术经济评价technical and economic evaluation技术系统technique system 机械machinery机械创新设计mechanical creation design, MCD 机械系统设计mechanical system design, MSD机械动力分析dynamic analysis of machinery 机械动力设计dynamic design of machinery机械动力学dynamics of machinery 机械的现代设计modern machine design机械系统mechanical system 机械利益mechanical advantage机械平衡balance of machinery 机械手manipulator机械设计machine design; mechanical design 机械特性mechanical behavior机械调速mechanical speed governors 机械效率mechanical efficiency机械原理theory of machines and mechanisms 机械运转不均匀系数coefficient of speed fluctuation机械无级变速mechanical stepless speed changes 基础机构fundamental mechanism基本额定寿命basic rating life 基于实例设计case-based design,CBD基圆base circle 基圆半径radius of base circle基圆齿距base pitch 基圆压力角pressure angle of base circle基圆柱base cylinder 基圆锥base cone急回机构quick-return mechanism 急回特性quick-return characteristics急回系数advance-to return-time ratio 急回运动quick-return motion棘轮ratchet 棘轮机构ratchet mechanism棘爪pawl 极限位置extreme (or limiting) position极位夹角crank angle between extreme (or limiting) positions计算机辅助设计computer aided design, CAD计算机辅助制造computer aided manufacturing, CAM计算机集成制造系统computer integrated manufacturing system, CIMS计算力矩factored moment; calculation moment 计算弯矩calculated bending moment加权系数weighting efficient 加速度acceleration加速度分析acceleration analysis 加速度曲线acceleration diagram尖点pointing; cusp 尖底从动件knife-edge follower间隙backlash 间歇运动机构intermittent motion mechanism减速比reduction ratio 减速齿轮、减速装置reduction gear减速器speed reducer 减摩性anti-friction quality渐开螺旋面involute helicoids 渐开线involute渐开线齿廓involute profile 渐开线齿轮involute gear渐开线发生线generating line of involute 渐开线方程involute equation渐开线函数involute function 渐开线蜗杆involute worm渐开线压力角pressure angle of involute 渐开线花键involute spline简谐运动simple harmonic motion 键key键槽keyway 交变应力repeated stress交变载荷repeated fluctuating load 交叉带传动cross-belt drive交错轴斜齿轮crossed helical gears 胶合scoring角加速度angular acceleration 角速度angular velocity角速比angular velocity ratio 角接触球轴承angular contact ball bearing角接触推力轴承angular contact thrust bearing 角接触向心轴承angular contact radial bearing角接触轴承angular contact bearing 铰链、枢纽hinge校正平面correcting plane 接触应力contact stress接触式密封contact seal 阶梯轴multi-diameter shaft结构structure 结构设计structural design截面section 节点pitch point节距circular pitch; pitch of teeth 节线pitch line节圆pitch circle 节圆齿厚thickness on pitch circle节圆直径pitch diameter 节圆锥pitch cone节圆锥角pitch cone angle 解析设计analytical design紧边tight-side 紧固件fastener径节diametral pitch 径向radial direction径向当量动载荷dynamic equivalent radial load 径向当量静载荷static equivalent radial load径向基本额定动载荷basic dynamic radial load rating径向基本额定静载荷basic static radial load tating径向接触轴承radial contact bearing 径向平面radial plane径向游隙radial internal clearance 径向载荷radial load径向载荷系数radial load factor 径向间隙clearance静力static force 静平衡static balance静载荷static load 静密封static seal局部自由度passive degree of freedom 矩形螺纹square threaded form锯齿形螺纹buttress thread form 矩形牙嵌式离合器square-jaw positive-contact clutch绝对尺寸系数absolute dimensional factor 绝对运动absolute motion绝对速度absolute velocity 均衡装置load balancing mechanism抗压强度compression strength 开口传动open-belt drive开式链open kinematic chain 开链机构open chain mechanism可靠度degree of reliability 可靠性reliability可靠性设计reliability design, RD 空气弹簧air spring空间机构spatial mechanism 空间连杆机构spatial linkage空间凸轮机构spatial cam 空间运动副spatial kinematic pair空间运动链spatial kinematic chain 框图block diagram空转idle 宽度系列width series雷诺方程Reynolds‘s equation 离心力centrifugal force离心应力centrifugal stress 理论廓线pitch curve离合器clutch 离心密封centrifugal seal理论啮合线theoretical line of action 隶属度membership 力force力多边形force polygon 力封闭型凸轮机构force-drive (or force-closed) cam mechanism力矩moment 力平衡equilibrium力偶couple 力偶矩moment of couple连杆connecting rod, coupler 连杆机构linkage连杆曲线coupler-curve 连心线line of centers链chain 链传动装置chain gearing链轮sprocket ; sprocket-wheel ; sprocket gear ; chain wheel 联组V 带tight-up V belt联轴器coupling ; shaft coupling 两维凸轮two-dimensional cam临界转速critical speed 六杆机构six-bar linkage龙门刨床double Haas planer 轮坯blank轮系gear train 螺杆screw螺距thread pitch 螺母screw nut螺旋锥齿轮helical bevel gear 螺钉screws螺栓bolts 螺纹导程lead螺纹效率screw efficiency 螺旋传动power screw螺旋密封spiral seal 螺纹thread (of a screw)螺旋副helical pair 螺旋机构screw mechanism螺旋角helix angle 螺旋线helix ,helical line绿色设计green design ; design for environment 马耳他机构Geneva wheel ; Geneva gear马耳他十字Maltese cross 脉动无级变速pulsating stepless speed changes脉动循环应力fluctuating circulating stress 脉动载荷fluctuating load铆钉rivet 迷宫密封labyrinth seal密封seal 密封带seal belt密封胶seal gum 密封元件potted component密封装置sealing arrangement 面对面安装face-to-face arrangement面向产品生命周期设计design for product`s life cycle, DPLC名义应力、公称应力nominal stress模块化设计modular design, MD 模块式传动系统modular system模幅箱morphology box 模糊集fuzzy set模糊评价fuzzy evaluation 模数module摩擦friction 摩擦角friction angle摩擦力friction force 摩擦学设计tribology design, TD摩擦阻力frictional resistance 摩擦力矩friction moment摩擦系数coefficient of friction 摩擦圆friction circle磨损abrasion ;wear; scratching 末端执行器end-effector目标函数objective function 耐腐蚀性corrosion resistance耐磨性wear resistance 内齿轮internal gear挠性机构mechanism with flexible elements 挠性转子flexible rotor内齿圈ring gear内力internal force 内圈inner ring能量energy 能量指示图viscosity逆时针counterclockwise (or anticlockwise) 啮出engaging-out啮合engagement, mesh, gearing 啮合点contact points啮合角working pressure angle 啮合线line of action啮合线长度length of line of action 啮入engaging-in牛头刨床shaper 凝固点freezing point; solidifying point扭转应力torsion stress 扭矩moment of torque扭簧helical torsion spring 诺模图NomogramO 形密封圈密封O ring seal 盘形凸轮disk cam盘形转子disk-like rotor 抛物线运动parabolic motion疲劳极限fatigue limit 疲劳强度fatigue strength偏置式offset 偏( 心) 距offset distance偏心率eccentricity ratio 偏心质量eccentric mass偏距圆offset circle 偏心盘eccentric偏置滚子从动件offset roller follower 偏置尖底从动件offset knife-edge follower 偏置曲柄滑块机构offset slider-crank mechanism 拼接matching评价与决策evaluation and decision 平底宽度face width频率frequency 平带flat belt平带传动flat belt driving 平底从动件flat-face follower平分线bisector 平均应力average stress平均中径mean screw diameter 平均速度average velocity平衡balance 平衡机balancing machine平衡品质balancing quality 平衡平面correcting plane平衡质量balancing mass 平衡重counterweight平衡转速balancing speed 平面副planar pair, flat pair平面机构planar mechanism 平面运动副planar kinematic pair平面连杆机构planar linkage 平面凸轮planar cam平面凸轮机构planar cam mechanism 平面轴斜齿轮parallel helical gears普通平键parallel key 其他常用机构other mechanism in common use起动阶段starting period 启动力矩starting torque气动机构pneumatic mechanism 奇异位置singular position起始啮合点initial contact , beginning of contact 气体轴承gas bearing千斤顶jack 嵌入键sunk key强迫振动forced vibration 切齿深度depth of cut曲柄crank 曲柄存在条件Grashoff`s law曲柄导杆机构crank shaper (guide-bar) mechanism 曲柄滑块机构slider-crank (or crank-slider) mechanism曲柄摇杆机构crank-rocker mechanism 曲齿锥齿轮spiral bevel gear曲率curvature 曲率半径radius of curvature曲面从动件curved-shoe follower 曲线拼接curve matching曲线运动curvilinear motion 曲轴crank shaft驱动力driving force 驱动力矩driving moment (torque)全齿高whole depth 权重集weight sets球ball 球面滚子convex roller球轴承ball bearing 球面副spheric pair球面渐开线spherical involute 球面运动spherical motion球销副sphere-pin pair 球坐标操作器polar coordinate manipulator燃点spontaneous ignition 热平衡heat balance; thermal equilibrium人字齿轮herringbone gear 冗余自由度redundant degree of freedom柔轮flexspline 柔性冲击flexible impulse; soft shock柔性制造系统flexible manufacturing system; FMS 柔性自动化flexible automation 润滑油膜lubricant film 润滑装置lubrication device润滑lubrication 润滑剂lubricant三角形花键serration spline 三角形螺纹V thread screw三维凸轮three-dimensional cam 三心定理Kennedy`s theorem砂轮越程槽grinding wheel groove 砂漏hour-glass少齿差行星传动planetary drive with small teeth difference设计方法学design methodology设计变量design variable 设计约束design constraints深沟球轴承deep groove ball bearing 生产阻力productive resistance升程rise 升距lift实际廓线cam profile 十字滑块联轴器double slider coupling; Oldham‘s coupling矢量vector 输出功output work输出构件output link 输出机构output mechanism输出力矩output torque 输出轴output shaft输入构件input link 数学模型mathematic model实际啮合线actual line of action 双滑块机构double-slider mechanism, ellipsograph 双曲柄机构double crank mechanism 双曲面齿轮hyperboloid gear双头螺柱studs 双万向联轴节constant-velocity (or double) universal joint双摇杆机构double rocker mechanism 双转块机构Oldham coupling双列轴承double row bearing 双向推力轴承double-direction thrust bearing松边slack-side 顺时针clockwise瞬心instantaneous center 死点dead point四杆机构four-bar linkage 速度velocity速度不均匀( 波动) 系数coefficient of speed fluctuation速度波动speed fluctuation 速度曲线velocity diagram 速度瞬心instantaneous center of velocity塔轮step pulley 踏板pedal台钳、虎钳vice 太阳轮sun gear弹性滑动elasticity sliding motion 弹性联轴器elastic coupling ; flexible coupling弹性套柱销联轴器rubber-cushioned sleeve bearing coupling 套筒sleeve梯形螺纹acme thread form 特殊运动链special kinematic chain特性characteristics 替代机构equivalent mechanism调节modulation, regulation 调心滚子轴承self-aligning roller bearing调心球轴承self-aligning ball bearing 调心轴承self-aligning bearing调速speed governing 调速电动机adjustable speed motors调速系统speed control system 调压调速variable voltage control调速器regulator, governor 铁磁流体密封ferrofluid seal停车阶段stopping phase 停歇dwell同步带synchronous belt 同步带传动synchronous belt drive凸的，凸面体convex 凸轮cam凸轮倒置机构inverse cam mechanism 凸轮机构cam , cam mechanism凸轮廓线cam profile 凸轮廓线绘制layout of cam profile凸轮理论廓线pitch curve 凸缘联轴器flange coupling图册、图谱atlas 图解法graphical method推程rise 推力球轴承thrust ball bearing推力轴承thrust bearing 退刀槽tool withdrawal groove退火anneal 陀螺仪gyroscopeV 带V belt 外力external force外圈outer ring 外形尺寸boundary dimension万向联轴器Hooks coupling ; universal coupling 外齿轮external gear弯曲应力beading stress 弯矩bending moment腕部wrist 往复移动reciprocating motion往复式密封reciprocating seal 网上设计on-net design, OND微动螺旋机构differential screw mechanism 位移displacement位移曲线displacement diagram 位姿pose , position and orientation稳定运转阶段steady motion period 稳健设计robust design蜗杆worm 蜗杆传动机构worm gearing蜗杆头数number of threads 蜗杆直径系数diametral quotient蜗杆蜗轮机构worm and worm gear 蜗杆形凸轮步进机构worm cam interval mechanism蜗杆旋向hands of worm 蜗轮worm gear涡圈形盘簧power spring 无级变速装置stepless speed changes devices无穷大infinite 系杆crank arm, planet carrier现场平衡field balancing 向心轴承radial bearing向心力centrifugal force 相对速度relative velocity相对运动relative motion 相对间隙relative gap象限quadrant 橡皮泥plasticine细牙螺纹fine threads 销pin消耗consumption 小齿轮pinion小径minor diameter 橡胶弹簧balata spring修正梯形加速度运动规律modified trapezoidal acceleration motion修正正弦加速度运动规律modified sine acceleration motion斜齿圆柱齿轮helical gear 斜键、钩头楔键taper key泄漏leakage 谐波齿轮harmonic gear谐波传动harmonic driving 谐波发生器harmonic generator斜齿轮的当量直齿轮equivalent spur gear of the helical gear心轴spindle 行程速度变化系数coefficient of travel speed variation行程速比系数advance-to return-time ratio 行星齿轮装置planetary transmission行星轮planet gear 行星轮变速装置planetary speed changing devices行星轮系planetary gear train 形封闭凸轮机构positive-drive (or form-closed) cam mechanism虚拟现实virtual reality 虚拟现实技术virtual reality technology, VRT虚拟现实设计virtual reality design, VRD 虚约束redundant (or passive) constraint 许用不平衡量allowable amount of unbalance许用压力角allowable pressure angle 许用应力allowable stress; permissible stress 悬臂结构cantilever structure 悬臂梁cantilever beam循环功率流circulating power load 旋转力矩running torque旋转式密封rotating seal 旋转运动rotary motion选型type selection 压力pressure压力中心center of pressure 压缩机compressor压应力compressive stress 压力角pressure angle牙嵌式联轴器jaw (teeth) positive-contact coupling雅可比矩阵Jacobi matrix 摇杆rocker液力传动hydrodynamic drive 液力耦合器hydraulic couplers液体弹簧liquid spring 液压无级变速hydraulic stepless speed changes液压机构hydraulic mechanism 一般化运动链generalized kinematic chain移动从动件reciprocating follower 移动副prismatic pair, sliding pair移动关节prismatic joint 移动凸轮wedge cam盈亏功increment or decrement work 应力幅stress amplitude应力集中stress concentration 应力集中系数factor of stress concentration 应力图stress diagram 应力—应变图stress-strain diagram优化设计optimal design 油杯oil bottle油壶oil can 油沟密封oily ditch seal有害阻力useless resistance 有益阻力useful resistance有效拉力effective tension 有效圆周力effective circle force有害阻力detrimental resistance余弦加速度运动cosine acceleration (or simple harmonic) motion预紧力preload 原动机primer mover圆带round belt 圆带传动round belt drive圆弧齿厚circular thickness 圆弧圆柱蜗杆hollow flank worm圆角半径fillet radius 圆盘摩擦离合器disc friction clutch圆盘制动器disc brake 原动机prime mover原始机构original mechanism 圆形齿轮circular gear圆柱滚子cylindrical roller 圆柱滚子轴承cylindrical roller bearing圆柱副cylindric pair 圆柱式凸轮步进运动机构barrel (cylindric) cam圆柱螺旋拉伸弹簧cylindroid helical-coil extension spring圆柱螺旋扭转弹簧cylindroid helical-coil torsion spring圆柱螺旋压缩弹簧cylindroid helical-coil compression spring圆柱凸轮cylindrical cam 圆柱蜗杆cylindrical worm圆柱坐标操作器cylindrical coordinate manipulator圆锥螺旋扭转弹簧conoid helical-coil compression spring圆锥滚子tapered roller 圆锥滚子轴承tapered roller bearing圆锥齿轮机构bevel gears 圆锥角cone angle。
机械专业英语词汇(英汉对照)
机械专业英语词汇金属切削metal cutting机床machine tool金属工艺学technology of metals刀具cutter摩擦friction联结link传动drive/transmission轴shaft弹性elasticity频率特性frequency characteristic误差error响应response定位allocation机床夹具jig动力学dynamic运动学kinematic静力学static分析力学analyse mechanics拉伸pulling压缩hitting剪切shear扭转twist弯曲应力bending stress强度intensity三相交流电three-phase AC磁路magnetic circles变压器transformer异步电动机asynchronous motor 几何形状geometrical精度precision正弦形的sinusoid交流电路AC circuit机械加工余量machining allowance 变形力deforming force变形deformation应力stress硬度rigidity热处理heat treatment退火anneal正火normalizing脱碳decarburization渗碳carburization电路circuit半导体元件semiconductor element反馈feedback发生器generator直流电源DC electrical source门电路gate circuit逻辑代数logic algebra外圆磨削external grinding内圆磨削internal grinding平面磨削plane grinding变速箱gearbox离合器clutch绞孔fraising绞刀reamer螺纹加工thread processing螺钉screw铣削mill铣刀milling cutter功率power工件workpiece齿轮加工gear mechining齿轮gear主运动main movement主运动方向direction of main movement 进给方向direction of feed进给运动feed movement合成进给运动resultant movement of feed 合成切削运动resultant movement ofcutting合成切削运动方向direction of resultant movement of cutting切削深度cutting depth前刀面rake face刀尖nose of tool前角rake angle后角clearance angle龙门刨削planing主轴spindle主轴箱headstock卡盘chuck加工中心machining center车刀lathe tool车床lathe钻削镗削bore车削turning磨床grinder基准benchmark钳工locksmith锻forge压模stamping焊weld拉床broaching machine拉孔broaching装配assembling铸造found流体动力学fluid dynamics流体力学fluid mechanics加工machining液压hydraulic pressure切线tangent机电一体化mechanotronics mechanical-electrical integration气压air pressure pneumatic pressure稳定性stability介质medium液压驱动泵fluid clutch液压泵hydraulic pump阀门valve失效invalidation强度intensity载荷load应力stress安全系数safty factor可靠性reliability螺纹thread螺旋helix键spline销pin滚动轴承rolling bearing滑动轴承sliding bearing弹簧spring制动器arrester brake十字结联轴节crosshead联轴器coupling链chain皮带strap精加工finish machining粗加工rough machining变速箱体gearbox casing腐蚀rust氧化oxidation磨损wear耐用度durability随机信号random signal离散信号discrete signal超声传感器ultrasonic sensor集成电路integrate circuit挡板orifice plate残余应力residual stress套筒sleeve扭力torsion冷加工cold machining电动机electromotor汽缸cylinder过盈配合interference fit热加工hotwork摄像头CCD camera倒角rounding chamfer优化设计optimal design工业造型设计industrial moulding design 有限元finite element滚齿hobbing插齿gear shaping伺服电机actuating motor铣床milling machine钻床drill machine镗床boring machine步进电机stepper motor丝杠screw rod导轨lead rail组件subassembly可编程序逻辑控制器ProgrammableLogic Controller PLC电火花加工electric spark machining 电火花线切割加工electrical dischargewire - cutting相图phase diagram热处理heat treatment固态相变solid state phase changes 有色金属nonferrous metal陶瓷ceramics合成纤维synthetic fibre电化学腐蚀electrochemical corrosion 车架automotive chassis悬架suspension转向器redirector变速器speed changer板料冲压sheet metal parts孔加工spot facing machining车间workshop工程技术人员engineer气动夹紧pneuma lock数学模型mathematical model画法几何descriptive geometry机械制图Mechanical drawing投影projection视图view剖视图profile chart标准件standard component零件图part drawing装配图assembly drawing尺寸标注size marking技术要求technical requirements刚度rigidity内力internal force位移displacement截面section疲劳极限fatigue limit断裂fracture塑性变形plastic distortion脆性材料brittleness material刚度准则rigidity criterion垫圈washer垫片spacer直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear直齿锥齿轮straight bevel gear运动简图kinematic sketch齿轮齿条pinion and rack蜗杆蜗轮worm and worm gear虚约束passive constraint曲柄crank摇杆racker凸轮cams共轭曲线conjugate curve范成法generation method定义域definitional domain值域range导数\\微分differential coefficient求导derivation定积分definite integral不定积分indefinite integral曲率curvature偏微分partial differential毛坯rough游标卡尺slide caliper千分尺micrometer calipers攻丝tap二阶行列式second order determinant 逆矩阵inverse matrix线性方程组linear equations概率probability随机变量random variable排列组合permutation and combination 气体状态方程equation of state of gas动能kinetic energy势能potential energy机械能守恒conservation of mechanicalenergy动量momentum桁架truss轴线axes余子式cofactor逻辑电路logic circuit触发器flip-flop脉冲波形pulse shape数模digital analogy液压传动机构fluid drive mechanism 机械零件mechanical parts淬火冷却quench淬火hardening回火tempering调质hardening and tempering磨粒abrasive grain结合剂bonding agent砂轮grinding wheel机械零件mechanical parts淬火冷却quench淬火hardening回火tempering调质hardening and tempering磨粒abrasive grain结合剂bonding agent砂轮grinding wheel机床行业部分英汉对照（1)：按英文字母排序3-Jaws indexing spacers 三爪、分割工具头A.T.C.system 加工中心机刀库Aluminum continuous melting & holding fu rnaces 连续溶解保温炉Balancing equipment 平衡设备Bayonet 卡口Bearing fittings 轴承配件Bearing processing equipment 轴承加工机Bearings 轴承Belt drive 带传动Bendingmachines 弯曲机Blades刀片Blades,saw 锯片Bolts,screws & nuts 螺栓,螺帽及螺丝Boring heads 搪孔头Boring machines 镗床Cable making tools 造线机Casting,aluminium 铸铝Casting,copper 铸铜Casting,gray iron 铸灰口铁Casting,malleable iron 可锻铸铁Casting,other 其他铸造Casting,steel 铸钢Chain drive 链传动Chain making tools 造链机Chamfer machines 倒角机Chucks 夹盘Clamping/holding systems 夹具/支持系统CNC bending presses 电脑数控弯折机CNC boring machines 电脑数控镗床CNC drilling machines 电脑数控钻床CNC EDM wire-cutting machines 电脑数控电火花线切削机CNC electric discharge machines 电脑数控电火花机CNC engraving machines 电脑数控雕刻机CNC grinding machines 电脑数控磨床CNC lathes 电脑数控车床CNC machine tool fittings 电脑数控机床配件CNC milling machines 电脑数控铣床CNC shearing machines 电脑数控剪切机CNC toolings CNC 刀杆CNC wire-cutting machines 电脑数控线切削机Conveying chains 输送链Coolers 冷却机Coupling联轴器Crimping tools 卷边工具Cutters 刀具Cutting-off machines 切断机Diamond cutters 钻石刀具Dicing saws 晶圆切割机Diecasting dies 压铸冲模Diecasting machines 压铸机Dies-progressive 连续冲模Disposable toolholder bits 舍弃式刀头Drawing machines 拔丝机Drilling machines 钻床Drilling machines bench 钻床工作台Drilling machines,high-speed 高速钻床Drilling machines,multi-spindle 多轴钻床Drilling machines,radial 摇臂钻床Drilling machines,vertical 立式钻床drills钻头Electric discharge machines(EDM) 电火花机Electric power tools 电动刀具Engraving machines 雕刻机Engraving machines,laser 激光雕刻机Etchin g machines 蚀刻机Finishing machines 修整机Fixture 夹具Forging dies 锻模Forging,aluminium 锻铝Forging,cold 冷锻Forging,copper 铜锻Forging,other 其他锻造Forging,steel 钢锻Foundry equipment 铸造设备Gear cutting machines 齿轮切削机Gears 齿轮Gravity casting machines 重力铸造机Grinde r bench 磨床工作台Grinders,thread 螺纹磨床Grinders,tools & cutters 工具磨床Grinders,ultrasonic 超声波打磨机Grinding machines 磨床Grinding machines,centerless 无心磨床Grinding machines,cylindrical 外圆磨床Grinding machines,universal 万能磨床Grinding tools 磨削工具Grinding wheels 磨轮Hand tools 手工具Hard/soft and free expansion sheet making plant 硬(软)板(片)材及自由发泡板机组Heat preserving furnaces 保温炉Heating treatment funaces 熔热处理炉Honing machines 搪磨机Hydraulic components 液压元件Hydraulic power tools 液压工具Hydraulic power units 液压动力元件Hydra ulic rotary cylinders 液压回转缸Jigs 钻模Lapping machines 精研机Lapping machines,centerless 无心精研机Laser cutting 激光切割Laser cutting for SMT stensil 激光钢板切割机Lathe bench 车床工作台Lathes,automatic 自动车床Lathes,heavy-duty 重型车床Lathes,high-speed 高速车床Lathes,turret 六角车床Lathes,vertical 立式车床Lubricants 润滑液Lubrication Systems 润滑系统Lubricators 注油机Machining centers,general 通用加工中心Machining centers,horizontal 卧式加工中心Machining centers,horizontal & vertical 卧式及立式加工中心Machining centers,vertical 立式加工中心Machining centers,vertical double-column ty pe 立式双柱加工中心Magnetic tools 磁性工具Manifolds 集合管Milling heads 铣头Milling machines 铣床Milling machines,bed type 床身式铣床Milling machines,duplicating 仿形铣床Milling machines,horizontal 卧式铣床Millin g machines,turret vertical 六角立式铣床Milling machines,universal 万能铣床Milling machines,vertical 立式铣床Milling machines,vertical & horizontal 立式及卧式铣床Mold & die components 模具单元Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Nail making machines 造钉机Oil coolers 油冷却器Overflow cutting machines for aluminium w heels 铝轮冒口切断机P type PVC waterproof rolled sheet making plant P 型PVC 高分子防水PCB fine piecing systems 印刷电器板油压冲孔脱料系统Pipe & tube making machines 管筒制造机Planing machines 刨床Planing machines vertical 立式刨床Pneumatic hydraulic clamps 气油压虎钳Pneumatic power tools 气动工具Powder metallurgic forming machines 粉末冶金成型机Presses,cold forging 冷锻冲压机presses,crank 曲柄压力机Presses,eccentric 离心压力机Presses,forging 锻压机Presses,hydraulic 液压冲床Presses,knuckle joint 肘杆式压力机Presses,pneumatic 气动冲床Presses,servo 伺服冲床Presses,transfer 自动压力机Pressingdies 压模Punch formers 冲子研磨器Quick die change systems 速换模系统Quick mold change systems 快速换模系统Reverberatory furnaces 反射炉Rollers 滚筒Rolling machines 辗压机Rotary tables 转台Sawing machines 锯床Sawing machines,band 带锯床Saws,band 带锯Saws,hack 弓锯Saws,horizontalband 卧式带锯Saws,verticalband 立式带锯shafts 轴Shapers 牛头刨床Shearing machines 剪切机Sheet metal forming machines 金属板成型机Sheet metal working machines 金属板加工机Slotting machines 插床spindles 主轴Stampingparts 冲压机Straightening machines 矫直机Switches & buttons 开关及按钮Tapping machines 攻螺丝机Transmitted chains 传动链Tubebending machines 弯管机Vertical hydraulic broaching machine 立式油压拉床Vises 虎钳Vises,tool-maker 精密平口钳Wheel dressers 砂轮修整器Woven-Cutting machines 织麦激光切割机Wrenches 扳手螺丝词汇的中英文对照六角盖头螺帽HEX CAP NUTS六角锯齿螺帽HEX SERRATED NUTS六角轮缘螺帽HEX FLANGE NUTS 高脚螺帽HEX COUPLING NUTS(HIGH NUT S) 圆螺帽ROUND NUTS四角螺帽SQUARE NUTSHEAVY HEX NUTS不锈钢六角螺帽STAINLESS STEEL HEX NUTS不锈钢尼龙嵌入螺帽STAINLESS STEEL NYLON INSERT LOCK NUTS普通六角螺帽HEX NUTS六角重型螺帽HEAVY HEX NUTS薄型螺帽HEX JAM NUTS尼龙嵌入防松螺帽NYLON INSERT LOCK NUTS机械螺丝用六角螺帽HEX MACHINE SCREW NUT机械工具英语机械工具spanner 扳子(美作:wrench) doub le-ended spanner 双头扳子adjustable spanner, monkey wrench 活扳子,活络扳手box spanner 管钳子(美作:socket wrench) c alipers 卡规pincers, tongs 夹钳shears 剪子hacksa w 钢锯wire cutters 剪线钳multipurpose pliers,universal pliers 万能手钳adjustable pliers 可调手钳punch 冲子drill 钻chuck 卡盘scraper 三角刮刀reamer 扩孔钻calliper gauge 孔径规rivet 铆钉nut 螺母locknut 自锁螺母, 防松螺母bolt 螺栓pin, peg, dowel 销钉washer 垫圈stapl e U 形钉oil can 油壶jack 工作服grease gun 注油枪机械加工抛光polishing 安装to assem ble 衬套bushing 外贸常用机械英语大全Assembly line 组装线Layout 布置图Conveyer流水线物料板Rivettable 拉钉机Rivet gun拉钉枪Screw driver 起子Pneumatic screw driver 气动起子worktable 工作桌OOBA 开箱检查fit together 组装在一起fasten 锁紧( 螺丝)fixture 夹具( 治具)pallet 栈板barcode 条码barcode scanner 条码扫描器fuse together 熔合fuse machine 热熔机repair 修理operator 作业员QC 品管supervisor 课长ME 制造工程师MT 制造生技cosmetic inspect 外观检查inner parts inspect 内部检查thumb screw 大头螺丝lbs. inch 镑、英寸EMI gasket 导电条front plate 前板rear plate 后板chassis 基座bezel panel 面板powerbutton 电源按键resetbutton 重置键Hi-pot test of SPS 高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts 塑胶件SOP 制造作业程序material check list 物料检查表work cell 工作间trolley 台车carton 纸箱sub-line 支线left fork 叉车personnel resource department 人力资源部production department 生产部门planning department 企划部QC Section 品管科stamping factory 冲压厂painting factory 烤漆厂molding factory 成型厂common equipment 常用设备uncoiler and straightener 整平机punching machine 冲床robot 机械手hydraulic machine 油压机lathe 车床planer |plein|刨床miller 铣床grinder 磨床linear cutting 线切割electrical sparkle 电火花welder 电焊机staker=reviting machine 铆合机position 职务president 董事长generalmanager 总经理special assistant manager 特助factory director 厂长department director 部长deputy manager | =vice manager 副理sectio n supervisor 课长deputy section supervisor =vice section supe risor 副课长group leader/supervisor 组长line supervisor 线长assistant manager 助理to move, to carry, to handle 搬运be put in storage 入库pack packing 包装to apply oil 擦油tofile burr 锉毛刺final inspection 终检to connect material 接料to reverse material 翻料wet station 沾湿台Tiana天那水cleaning cloth 抹布toload material 上料to unload material 卸料to return material/stock to 退料scraped |\\'skr?pid|报废scrape ..v.刮;削deficient purchase 来料不良manufacture procedure 制程deficient manufacturing procedure 制程不良oxidation |\\' ksi\\'dei?n|氧化scratch 刮伤dents 压痕defective upsiding down 抽芽不良defective to staking 铆合不良embedded lump 镶块feeding is not in place 送料不到位stamping-missing 漏冲production capacity 生产力education and training 教育与训练proposal improvement 提案改善spare parts=buffer 备件forklift 叉车trailer=long vehicle 拖板车外贸常用机械英语大全(续)compound die 合模die locker 锁模器pressure plate=plate pinch 压板bolt 螺栓administration/general affairs dept 总务部automatic screwdriver 电动启子thickness gauge 厚薄规gauge(or jig)治具power wire 电源线buzzle 蜂鸣器defective product label 不良标签identifying sheet list 标示单location 地点present members 出席人员subject 主题conclusion 结论decision items 决议事项responsible department 负责单位pre-fixed finishing date 预定完成日approved by / checked by / prepared by 核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model 机锺work order 工令revision 版次remark 备注production control confirmation 生产确认checked by 初审approved by 核准department 部门stock age analysis sheet 库存货龄分析表on-hand inventory 现有库存available material 良品可使用obsolete material 良品已呆滞to be inspected or reworked 待验或重工total 合计cause description 原因说明part number/ P/N 料号type 形态item/group/class 类别quality 品质prepared by 制表notes 说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physicalinventory 盘点数量physical count quantity 帐面数量difference quantity 差异量cause analysis 原因分析raw materials 原料materials 物料finished product 成品semi-finished product 半成品packing materials 包材good product/accepted goods/ acceptedparts/good parts 良品defective product/non-good parts 不良品disposed goods 处理品warehouse/hub 仓库on way location 在途仓oversea location 海外仓spare parts physical inventory list 备品盘点清单spare molds location 模具备品仓skid/pallet 栈板tox machine 自铆机wire EDM 线割EDM 放电机coilstock 卷料sheetstock 片料tolerance 工差score=groove 压线cam block 滑块pilot 导正筒trim 剪外边pierce 剪内边drag form 压锻差pocket for the punch head 挂钩槽slug hole 废料孔feature die 公母模expansion dwg 展开图radius 半径shim(wedge)楔子torch-flame cut 火焰切割set screw 止付螺丝form block 折刀stop pin 定位销round pierce punch=die button 圆冲子shape punch=die insert 异形子stock locater block 定位块under cut=scrap chopper 清角active plate 活动板baffle plate 挡块cover plate 盖板male die 公模female die 母模groove punch 压线冲子air-cushion eject-rod 气垫顶杆spring-box eject-plate 弹簧箱顶板bushing block 衬套insert 入块club car 高尔夫球车capability 能力parameter 参数factor 系数phosphate 皮膜化成viscosity 涂料粘度alkalidipping 脱脂main manifold 主集流脉bezel 斜视规blanking 穿落模dejecting 顶固模demagnetization 去磁;消磁high-speed transmission 高速传递heat dissipation 热传rack 上料degrease 脱脂rinse 水洗alkaline etch 龄咬desmut 剥黑膜D.I. rinse 纯水次Chromate 铬酸处理Anodize 阳性处理seal 封孔revision 版次part number/P/N 料号good products 良品scraped products 报放心品defective products 不良品finished products 成品disposed products 处理品barcode 条码flow chart 流程表单assembly 组装stamping 冲压molding 成型spare parts=buffer 备品coordinate 座标dismantle the die 折模auxiliary fuction 辅助功能poly-line 多义线heater band 加热片thermocouple 热电偶sand blasting 喷沙grit 砂砾derusting machine 除锈机degate 打浇口dryer烘干机induction 感应induction light 感应光response=reaction=interaction 感应ram 连杆edge finder 巡边器concave 凸convex 凹short 射料不足nick 缺口speck 瑕??shine 亮班splay 银纹gas mark 焦痕delamination 起鳞cold slug 冷块blush 导色gouge 沟槽;凿槽satin texture 段面咬花witness line 证示线patent 专利grit 沙砾granule=peuet=grain 细粒grit maker 抽粒机cushion 缓冲magnalium 镁铝合金magnesium 镁金metal plate 钣金lathe 车mill 锉plane 刨grind 磨drill 铝boring 镗blinster 气泡fillet 镶;嵌边through-hole form 通孔形式voller pin formality 滚针形式cam driver 铡楔shank 摸柄crank shaft 曲柄轴augular offset 角度偏差velocity 速度production tempo 生产进度现状torque 扭矩spline=the multiple keys 花键quenching 淬火tempering 回火annealing 退火carbonization 碳化tungsten high speed steel 钨高速的moly high speed steel 钼高速的organic solvent 有机溶剂bracket 小磁导liaison 联络单volatile 挥发性resistance 电阻ion 离子titrator 滴定仪beacon 警示灯coolant 冷却液crusher 破碎机机械类常用英语：生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等) CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供应商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号阀门种类英汉术语对照Air valves 空气阀门Angle Stop valves 角式截止阀Angle Throttle Valves 角式节流阀Angle Type Globe Valves 门角式截止阀Ash valves 排灰阀Aspirating valves 吸（抽）气阀Auxiliary valves 辅助（副）阀Balance valves 平衡阀Bellows valves 波纹管阀Blowdown valves 泄料（放空，排污）阀Brake valves 制动阀Butterfly Type Non-slam Check 蝶式缓冲止回阀Butterfly Valves with Gear Actuator 蜗轮传动蝶阀Buttwelding valves 对焊连接阀Clamp valves 对夹式阀门Cock二通Combination valves 组合阀CQ Thread Ball Valves CQ 螺纹球阀Culvert valves 地下管道阀Deceleration valves 减速阀DiaphragmValves 隔膜阀Decompression valves泄压阀Double Disc Flat Gate Valves 双闸板平板闸阀Double Disk Parallel Gate Valves 明杆平行式双闸板闸板Double Opening Exhaust Valves 双口排气球Drainage valves 排水阀Electric Actuated Stop Valves 电动截止阀Electric Actuated Wedge Gate Valves 电动楔式闸阀Electric Double Disk Parallel Gate Valve s 电动平行式双闸板闸板Emergeny Cut-off Valves 紧急切断阀Exhaust valves 排气阀Free Float Type Steam Trap 浮球式疏水阀Flange Ball Valves 法兰球阀Flange Gate Valves 法兰闸阀Flange Globe Valves 法兰截止阀Gauge Valves 仪表阀Hand-operated valves 手动阀Hard Seal Butterfly Valves 金属密封碟阀High Temperature Pressure Power Statio n Gate Valves 高温高压电站闸阀High Temperature Pressure Power Statio n Globe Valves 高温高压电站截止阀Hydraulic relay valves 液压继动阀Lift Check Valves 升降式止回阀Lift Check Valves 升降式止回阀Limit valves 限位阀Lining Ball Valves 衬里球阀Lining Butterfly Valves 衬里碟阀Lining Check Valves 衬里止回阀Lining Cock 衬里二通Lining Globe Valves 衬里截止阀Lining T-Cock Valves 衬里三通旋塞阀Liquid Indicator 液位计LPG Pipe Fitting 液化气管件Magnetic Co-operate Globe Valves 磁耦合截止阀Magnetism Forle Pumps 磁力泵Manual Oil Pumps Valves 手摇油泵(阀)Meter Needle Type Globe Valves 仪表针形截止阀Oblique Stop Valves 直流式截止阀Parallel Slide Valves 浆液阀Pintle valve 针形阀Piping Centrifugal Pumps 管道离心泵Plunger valves 柱塞阀Pressure valve 压力（増压）阀Piping Pumps 管道泵Piping Safety Valves 管道安全阀Plunger Globe Valves 柱塞截止阀Quick Draining Valves 快速排污阀Restrictor Valves 过流阀(或节流阀) Safety Valves 安全阀Screw Pumps 螺杆泵Scum Gate Valves 排渣闸阀S olenoid valves 电磁阀Single Disc Flat Gate Valves 单闸板平板闸阀Single Opening Exhaust Valves 单口排气球Slurry Pumps 泥浆泵Stop Valves 截止阀Strainer 过滤器Submerged Motor Pumps 潜水电泵(排污泵)Swing Check Valves 旋启式止回阀Swing Check Valves 旋启式止回阀Tank Lorry Ball Valves 槽车球阀T-Cock 三通Thin Gate Valves 薄型闸阀Throttle Valves 节流阀Tiny Drag Slow Shut Check Valves 微阻缓闭止回阀Triple (tee) valves 三通阀Two-way valves 二通阀Under Water Pumps 液下泵Vacuum Pumps 水力喷射器(真空泵) Vertical Lift Check Valves 立式止回阀Wafer Check Valves 对夹式止回阀Wafer plate valves 对夹蝶板阀Wafer Type Butterfly Valves with Rubber Itning 对夹式衬胶蝶阀Waste Valves 排污箱(阀)Water Seal Gate Valves 水封闸阀Wedge Gate Valves 楔式闸阀Y Type and Cylinder Filters Y 型筒型过滤器阀门零部件英汉术语对照Axis Guide 轴套Ball球、球芯Ball seat 密封圈Blowdown Sealing Face 启、阀件密封面Body 阀体Bonnet 阀盖Disc 阀瓣Mut 螺母Screw 螺栓Sealing 密封件Spring 弹簧Stem 阀杆Stem Mut 阀杆螺母Stem seal 填料Wedge Disc 闸板阀门规范技术英语术语对照Applicable medium 适用介质Applicable temperature 适用温度Butt Clamp 对夹Chemical analysis 化学成份Connecting format 连接形式Double disc 双闸板Flexible disc 弹性闸板Flange 法兰Hoop 卡箍Inside thread 内螺纹Jacket 夹套Mains 电源Material chemical analysis and mechanical capacity 材料化学成份和机械性能materials 材料Materials for main parts主要零件材料Mechanical capacity 机械性能Max. Discharging Capacity 最大排水量Max. Operating Temperature 最高工作温度Max. Allowable Temperature 最高允许温度Max. Allowable Pressure 最高允许压力Model 型号Name of parts 零件名称nitrogen (N) 氮Nominal bore 公称通径Nominal Pressure 公称压力Nozzle 排气口Outside thread 外螺纹Oxidant 氧化性介质Parallel 平行Piping 管路Piston 活塞Reductant 还原性介质Rising stem 明杆Seal 阀座，密封面Seat testing pressure 压力气密封试验压力Socket 卡套Specifications 性能规范Single disc 单闸板Solid 刚性Strengh testing pressure 强度试验压力Steam , condensate 蒸汽,凝结水Stroke 冲程，行程Water,oil,steam 水,温度,气Wedge 楔式Welding 焊接阀门材质术语英汉对照Atbas metal 镍铬钢Buna-N rubber 丁晴橡胶Casting aluminium brass 铸铝黄铜Casting aluminium bronze 铸铝青铜Ceramic metal 陶瓷金属Chromel alloy 镍铬合金CHR rubber 氯晴橡胶Chrominm-molybdenum-vanadium steel铬钼钒钢Chromium stainless steel 铬不锈钢Chromium-molybdenum steel 铬钼钢Corrugation pad 波形垫Cuprum alloy 铜合金Ductile Cast iron 球墨铸铁Expanded graphite 柔性石墨Fine Steel Casting iron 优质碳素钢Fluorous rubber 氟橡胶GrayCast iron 灰铸铁Hayne's alloy 钴铬钨合金Hightem perature steel 高温钢Monel 蒙乃尔合金Low temperature steel 低温钢Nylon 尼龙塑料Polytetrafluoroethylene(PTEF) 聚四氟乙烯Polythene 聚乙烯Pure aluminium 纯铝Pure cupper 纯铜Rubber graphite board 橡胶石墨板Spring steel 弹簧钢Stainless acid-resisting steel 不锈耐酸钢Stainless and Graphite 不锈钢/石墨Stainless steel 不锈钢Steel Casting iron 碳素钢铸件Shell Test Pressure 壳体试验压力Service Fluid 工作介质机械类常用英语：钢材类alloy tool steel 合金工具钢aluminium allo y 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized ste el sheet 镀锌铁板hard alloy steel 超硬合金钢high speed too l steel 高速度工具钢hot work die steel 热锻模用钢low alloy to ol steel 特殊工具钢low manganese casting steel 低锰铸钢marg ing steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 矽钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel ?钢vinyl tapped steel sheet 塑胶覆面钢板塑件模具相关英文compre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具encapsulation molding 低压封装成型、射出成型用模具two plate 两极式（模具）well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spindle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣airvent 排气道weldingline 熔合痕eject pin 顶出针knock pin 顶出销return pin 回位销反顶针sleave 套筒stripper plate 脱料板insert core 放置入子runner stripper plate 浇道脱料板guide pin 导销eject rod (bar)（成型机）顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orientation 定向sprue gate 射料浇口，直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆) slag well 冷料井side gate 侧浇口edgegate 侧缘浇口tabgate 搭接浇口filmgate 薄膜浇口flashgate 闸门浇口slitgate 缝隙浇口fangate 扇形浇口dishgate 因盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口subarine gate 潜入式浇口tunnel gate 隧道式浇口pin gate 针点浇口Runnerless 无浇道(sprue less)无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣。
机电,通讯设备词汇,中英法三语
压限器 切换器 音箱 扬声器 CD机 传声器 播放器 功放 音频控制主机
Pressure limiter Switches Speakers Loudspeakers CD player Microphone Players PA Audio control console
Limiteur de pression Commutateurs Boî de sonorisation te Haut-parleurs Lecteur de CD Microphone Joueurs PA Pupitre de commande audio 7 : Energie e mise àla terre Energie Gé rateurs né parafoudre barres de mise àla terre 8 : gestion de garage Dé tecteurs de vehicules Equipement d'entré et de sortie e Machine de distribution de cartes Dispositif d'identification de vé hicule Lecteurs 9 : Systè de sé me curité Dé tecteur d'intrusion Magné tomè tre Contrô d'alarme leur Alarme Contrô d'Accè le s Systè d'é me metteur-ré cepteur Camé ra Objectif Plateformes Support Commutateur de Matrice Magné toscope de disque dur Moniteurs Équipement d'alarme incendie Équipement d'alarme 10 : é quipement pé riphé rique Rack Câ assorti ble Accessoires
港口机电英语
港口机电英语词汇1.CONTAINER2.QUAYSIDE CONTAINER CRANE3.RUBBER-TYRED GANTRY4.RAIL-MOUNTED CRANE5.GANTRY CRANE6.FORKLIFT TRUCK7.LOADED CONTAINER HANDLER8.EMPTY CONTAINER HANDLER9.REATCH STACKER10.LOADER11.AC12.DC13.AUXILIARY POWER14.AIR COMPRESSOR15.BEARING16.BLOWER17.BRAKE18.CAM19.CABLE20.CABLE REEL21.CABIN22.CAPACITOR23.CHAIN24.CONTACTOR25.CYCLINDER26.COIL27.CONSOLE28.CRANKSHAFT29.COUPLINGMUNICATION31.CONTROL POWER32.ENGINE33.ELECTRICMAGNET34.ENCODE35.ELECTRICAL ROOM36.EARTHING37.FAN38.FILTER39.FUSE40.GUAGE41.GEAR42.GEAR BOX43.INDICATING LAMP44.LOADCELL45.LIMITED SWITCH46.LIMITED SWITCH47.MASTER CONTROLLER48.MOTOR49.PUMP50.NORMALLY OPEN /NORMALLY CLOSED51.PISTON52.PUSHBUTTON53.PULSE54.SPREADER55.SPREADER56.TWIST57.VALVE58.TRANSFORMER港口机电故障词汇1.I/O Error Master Panel2.PLC I/O Source AC Off （Master）3.Hoist-1 Deviation Check Fault4.Gantry-1 Deviation Check Fault5.Trolley Deviation Check Fault6.Boom Deviation Check Fault7.Boom Deviation Check Fault8.Boom Acc Check Fault9.Trolley Rotation Check Fault10.Trolley Motor Overload （Alarm）11.Trolley Motor Overload （Trip）12.Hoist Encoder Fault13.Hoist Controller （O、U、D North）Fault14.Gantry Controller （O、R、L North）Fault15.Trolley Controller （O、F、R North）Fault16.Mc Check Fault （Hoist Main）11M117.Mc Check Fault （Hoist Brake）11B18.Mc Check Fault （Trolley Blower）721Mc19.Mc Check Fault （Hoist Emergency Brake）901Mc20.Mc Check Fault （WS/LS Wheel Brake Pump）951Mc21.Mc Check Fault （T/C Pope Tension）1021Mc22.Mc Check Fault （Boom latch-1）1011Mc23.Mc Check Fault （Spreader Pump）1081Mc24.Mc Check Fault （T/C Pope Tension Coller）1032Mc25.Mc Check Fault （T/L/S -1）1041F26.Br Check Fault （Gantry Brake-1）Ls27.Operation Check Fault （20Ft）28.Operation Check Fault （40Ft）29.Operation Check Fault （Twistlock Lock）30.Operation Check Fault （Twistlock Unlock）31.Operation Check Fault （Twin Up）32.Operation Check Fault （Twin Down）33.Operation Check Fault （Boom Latch Left （Right）Raise）34.Operation Check Fault （Boom Latch ）35.No.1 Converter Fault36.No.1 Converter Ready Off37.No.1 Acl Fuse Blow38.Hh-1/Gt-1 Inverter Fault39.Hoist Slowdown Check Fault40.Hoist Upper Over41.Hoist Motor Overspeed42.Hoist Motor Overspeed43.Hoist Preset Error44.Spreader Interlock Off45.Hoist Operation Not Select46.Boom Level Off or Boom Latch Off47.Ttds Fault48.Hoist Lower Stopnded Ls On50.Pope Slack51.Sill Beam Stop52.Gantry Right Emergency End Stop53.Gantry Seaside Anchored-154.Spreader Interlock Off55.Hoist Encoder Fault56.Hoist Controller （Boom Level or 60 Degree Under）57.Seaside Wheel Brake Ls Off58.Shore Power On59.Trolley Anchor Left Ls On60.Trolley Washing Platform Gate Open61.Trolley Gate Open（Cabin side）62.Trolley Gate Open（Walkway side）。