模具,冲压相关英语专业翻译

模具工程类词汇英语翻译

模具工程类词汇英语翻译extension dwg睁开图plain die简略模procedure dwg工程图pierce die冲孔模die structure dwg模具构造图forming die成型模material材质progressive die连续模material thickness料片厚度gang dies复合模press specification冲床规格shearing die剪边模die height range合用模高riveting die铆合模die height闭模高度pierce冲孔burr毛边forming 成型 ( 抽凸 , 冲凸 )gap空隙draw hole抽孔punch wt.上模重量bending折弯模具词汇英语翻译 ( 模板类 ) trim 切边top plate上托板（顶板）emboss 凸点top block上垫脚dome 凸圆punch set上模座semi-shearing 半剪punch pad上垫板stamp mark冲记号punch holder上夹板deburr or coin压毛边stripper pad脱料背板punch riveting冲压铆合up stripper上脱料板side stretch侧冲压平male die公模 (凸模 )reel stretch卷圆压平feature die公母模groove压线female die母模(凹模 )blanking下料upper plate上模板stamp letter冲字(料号)lower plate下模板shearing剪断die pad下垫板tick-mark nearside正面压印die holder下夹板tick-mark farside反面压印die set下模座模具词汇英语翻译 ( 五金部件类 )bottom block下垫脚inner guiding post内导柱bottom plate下托板 (底板)inner hexagon screw内六角螺钉stripping plate内外打 ( 脱料板 ) dowel pin固定销outer stripper外脱料板coil spring弹簧inner stripper内脱料板lifter pin顶料销lower stripper下脱料板eq-height sleeves=spool等高套筒模具词汇英语翻译 ( 部件类 ) pin 销punch冲头lifter guide pin浮升导料销insert 入块 ( 嵌入件 )guide pin导正销deburring punch压毛边冲子wire spring圆线弹簧groove punch压线冲子outer guiding post外导柱stamped punch字模冲子stop screw止付螺丝round punch圆冲子located pin定位销special shape punch异形冲子outer bush外导套bending block折刀４模具词汇英语翻译 ( 冲压 )roller滚轴３baffle plate挡块located block定位块supporting block for location定位支承块air plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger增强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块模具词汇英语翻译 ( 塑件与模具 ) compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold切割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具（移转成型用模具）encapsulation molding低压封装成型（射出成型用模具）two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core搁置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷办理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销 ( 拉料杆 ) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate空隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔阂浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate地道式浇口pin gate针点浇口Runner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣模具词汇英语翻译 ( 模具钢材 )alloy tool steel合金工具钢aluminium alloy铝合金钢bearing alloy轴承合金blister steel浸碳钢bonderized steel sheet邦德防蚀钢板carbon tool steel碳素工具钢clad sheet 被覆板clod work die steel冷锻模用钢emery 金钢砂ferrostatic pressure钢铁水静压力forging die steel锻造模用钢galvanized steel sheet镀锌铁板hard alloy steel超硬合金钢high speed tool steel高速度工具钢hot work die steel热锻模用钢low alloy tool steel特别工具钢low manganese casting steel低锰铸钢marging steel马式体高强度热办理钢martrix alloy马特里斯合金meehanite cast iron米汉纳铸钢meehanite metal米汉纳铁merchant iron市售钢材molybdenum high speed steel钼系高速钢molybdenum steel钼钢nickel chromium steel镍铬钢prehardened steel顶硬钢silicon steel sheet矽钢板stainless steel不锈钢tin plated steel sheet镀锡铁板tough pitch copper韧铜troostite吐粒散铁tungsten steel钨钢vinyl tapped steel sheet塑胶覆面钢板模具词汇英语翻译 ( 工作机械 )3D coordinate measurement三次元量床boring machine搪孔机cnc milling machine CNC铣床contouring machine轮廓锯床copy grinding machine仿形磨床copy lathe仿形车床copy milling machine仿形铣床copy shaping machine仿形刨床cylindrical grinding machine外圆磨床die spotting machine合模机drilling machine冲孔机engraving machine雕琢机engraving雕模搁置加工机form grinding machine成形磨床graphite machine石墨加工机horizontal boring machine卧式搪孔机horizontal machine center卧式加工制造中心internal cylindrical machine内圆磨床jig boring machine冶具搪孔机jig grinding machine冶具磨床lap machine研磨机machine center加工制造中心multi model miller靠磨铣床NC drilling machine NC钻床NC grinding machine NC磨床 NC lathe NC 车床NC programming system NC程式制作系统planer龙门刨床profile grinding machine投影磨床projection grinder投影磨床radial drilling machine旋臂钻床shaper牛头刨床surface grinder平面磨床try machine试模机turret lathe转塔车床universal tool grinding machine全能工具磨床vertical machine center立式加工制造中心wire线割放电加工机模具词汇英语翻译 ( 模具厂常用之标准零配件 )air vent vale通气阀anchor pin锚梢angular pin角梢baffle调理阻板angular pin倾斜梢baffle plate折流档板dowel hole导套孔ball button球塞套dowel pin合模梢ball plunger定位球塞dozzle协助浇口ball slider球塞滑块dowel pin定位梢binder plate压板draft拔模锥度blank holder防皱压板draw bead张力调整杆blanking die落料冲头drive bearing传动轴承bolster上下模板ejection pad顶出衬垫bottom board浇注底板ejector脱模器bolster垫板ejector guide pin顶出导梢bottom plate下固定板ejector leader busher顶出导梢衬套bracket托架ejector pad顶出垫bumper block缓冲块ejector pin顶出梢buster堵口ejector plate顶出板casting ladle浇注包ejector rod顶出杆casting lug铸耳ejector sleeve顶出衬套cavity 模穴 ( 模仁 )ejector valve顶出阀cavity retainer plate模穴托板eye bolt 环首螺栓center pin中心梢filling core椿入蕊clamping block锁定块film gate薄膜形浇口coil spring螺旋弹簧finger pin指形梢cold punched nut冷冲螺母finish machined plate角形模板cooling spiral螺旋冷却栓finish machined round plate圆形模板core 心型fixed bolster plate固定侧模板core pin心型梢flanged pin带凸缘销cotter张口梢flash gate毛边形浇口cross 十字接头flask上箱cushion pin缓冲梢floating punch浮动冲头diaphragm gate盘形浇口gate 浇口die approach模头料道gate land浇口面die bed型底gib 凹形拉紧楔die block块形模体goose neck鹅颈管die body铸模座guide bushing指引衬套die bush合模衬套guide pin导梢die button冲模母模guide post指引柱die clamper夹模器guide plate导板die fastener模具固定用部件guide rail导轨die holder母模固定板head punch顶头冲孔die lip模唇headless punch直柄冲头die plate冲模板heavily tapered solid整体模蕊盒die set冲压模座hose nippler管接头direct gate直接浇口impact damper缓冲器dog chuck帮凶夹头injection ram压射柱塞dowel 定位梢inlay busher嵌入衬套inner plunger内柱塞inner punch内冲头insert嵌件insert pin嵌件梢king pin转向梢king pin bush主梢衬套knockout bar脱模杵land 合模平展面land area 合模面leader busher导梢衬套lifting pin起模顶销lining内衬locating center punch定位中心冲头locating pilot pin定位导梢locating ring定位环lock block压块locking block定位块locking plate定位板loose bush活动衬套making die打印冲子manifold block歧管档块master plate靠模样板match plate分型板mold base 塑胶模座mold clamp铸模紧固夹mold platen模用板moving bolster换模保持装置moving bolster plate可动侧模板one piece casting整体铸件parallel block平行垫块paring line分模线parting lock set合模定位器pass guide穴型导板peened head punch镶入式冲头pilot pin导销pin gate针尖浇口plate 衬板pre extrusion punch顶挤冲头punch 冲头puncher推杆pusher pin衬套梢rack 机架rapping rod起模杆re-entrant mold凹入模retainer pin嵌件梢retainer plate托料板return pin回位梢riding stripper浮动脱模器ring gate环型浇口roller滚筒runner 流道runner ejector set流道顶出器runner lock pin流道拉梢screw plug头塞set screw固定螺丝shedder脱模装置shim分开片shoe模座之上下模板shoot流道shoulder bolt肩部螺丝skeleton骨架slag riser冒渣口slide(slide core)滑块slip joint滑配接头spacer block间隔块spacer ring间隔环 spider 模蕊支架spindle主轴sprue注道sprue bushing 注道衬套sprue bushing guide注道导套sprue lock bushing注道定位衬套sprue puller注道拉料spue line合模线square key方键square nut方螺帽square thread方螺纹stop collar限位套stop pin止动梢stop ring止动环stopper定位停止梢straight pin圆柱销stripper bolt脱料螺栓stripper bushing脱模衬套stripper plate剥料板stroke end block行程止梢submarine gate潜入式浇口support pillar支撑支柱 / 顶出支柱support pin支撑梢supporting plate托板sweep templete造模刮板tab gate协助浇口taper key推拔键taper pin拔锥梢 / 锥形梢teeming浇注three start screw三条螺纹thrust pin推力销tie bar拉杵tunnel gate地道形浇口vent 通气孔wortle plate拉丝模板模具词汇英语翻译 ( 模具分类 ) bismuth mold铋铸模landed plunger mold有肩柱塞式模具burnishing die挤光模landed positive mold有肩全压式模具button die镶入式圆形凹模loading shoe mold料套式模具center-gated mold中心浇口式模具loose detail mold活部件模具chill mold冷硬用铸模loose mold活动式模具clod hobbing冷挤压制模louvering die百页窗冲切模composite dies复合模具manifold die分歧管模具counter punch 反凸模modular mold组合式模具double stack mold双层模具multi-cavity mold多模穴模具electroformed mold电铸成形模multi-gate mold复式浇口模具expander die扩径模offswt bending die双折冷弯模具extrusion die挤出模palletizing die叠层模family mold反套制品模具plaster mold石膏模blank through dies漏件式落料模porous mold通气性模具duplicated cavity plate复板模positive mold全压式模具fantail die扇尾形模具pressure die压紧模fishtail die鱼尾形模具profile die轮廓模flash mold溢料式模具progressive die次序模gypsum mold 石膏铸模protable mold手提式模具hot-runner mold热流道模具prototype mold雏形试验模具ingot mold钢锭模punching die落料模lancing die切口模raising(embossing)压花起伏成形re-entrant mold倒角式模具sectional die拼合模runless injection mold无流道冷料模具sectional die对合模具segment mold组合模semi-positive mold半全压式模具shaper 定型模套single cavity mold单腔模具solid forging die整体锻模split forging die拼合锻模split mold双并式模具sprueless mold无注道残料模具squeezing die挤压模stretch form die拉伸成形模sweeping mold平刮铸模swing die振动模具three plates mold三片式模具trimming die切边模unit mold单元式模具universal mold通用模具unscrewing mold 退扣式模具yoke type die轭型模accurate die casting精细压铸powder forming粉末成形calendaring molding压延成形powder metal forging粉末锻造cold chamber die casting冷式压铸precision forging精细锻造cold forging冷锻press forging冲锻compacting molding粉末压出成形rocking die forging摇动锻造epoxy resin环氧树脂 EPcompound molding复合成形ethyl cellulose乙基纤维素rotary forging展转锻造ethylene vinylacetate copolymer乙烯 -compression molding压缩成形醋酸乙烯 EVArotational molding离心成形ethylene-vinlacetate copolyme醋酸乙烯dip mold浸渍成形共聚物 EVArubber molding橡胶成形fiber reinforcement纤维增强热固性 / 纤encapsulation molding注入成形维增强复合资料sand mold casting砂模锻造high density polyethylene高密度聚乙烯extrusion molding挤出成形HDPEshell casting壳模锻造high impact polystyrene高冲击聚苯乙烯foam forming泡沫成形HIPSsinter forging烧结锻造high impact polystyrene rigidity高冲forging roll轧锻击性聚苯乙烯six sides forging六面锻造low density polyethylene低密度聚乙烯gravity casting重力锻造LDPEslush molding凝塑成形melamine resin三聚氰胺酚醛树脂 MF hollow(blow) molding中空(吹出 )成形nitrocellulose硝酸纤维素squeeze casting高压锻造phenolic resin酚醛树脂hot chamber die casting热室压铸plastic塑胶swaging挤锻polyacrylic acid聚丙烯酸 PAPhot forging热锻polyamide 耐龙 PAtransfer molding转送成形polybutyleneterephthalate聚对苯二甲injection molding射出成形酸丁酯 PBTwarm forging温锻polycarbonate聚碳酸酯 PCinvestment casting精细锻造polyethyleneglycol聚乙二醇 PFG matched die method对模成形法polyethyleneoxide聚氧化乙烯 PEO laminating method被覆淋膜成形polyethyleneterephthalate聚乙醇对苯low pressure casting低压锻造PETPlost wax casting脱蜡锻造polymetylmethacrylate聚甲基丙烯酸甲matched mould thermal forming对模热成酯 PMMA形模polyoxymethylene聚缩醛 POM模具词汇英语翻译 ( 塑胶原料 )polyphenylene oxide聚硫化亚苯acrylic压克力polyphenyleneoxide聚苯醚 PPOcasein酪素polypropylene聚丙烯 PPcellulose acetate醋酸纤维素 CA polystyrene聚苯乙烯 PScellulose acetate butyrate醋酸丁酸纤polytetrafluoroethylene聚四氟乙烯维素 CAB PTFEcomposite material复合资料polytetrafluoroethylene聚四氟乙烯cresol resin甲酚树脂 CF polythene聚乙烯 PEdially phthalate苯二甲酸二烯丙酯polyurethane聚氨基甲酸酯 PUdisperse reinforcement分别性增强复合polyvinylacetate聚醋酸乙烯 PVAC资料polyvinylalcohol聚乙烯醇 PVA engineering plastics工程塑胶polyvinylbutyral聚乙烯醇缩丁醛 PVBpolyvinylchloride聚氯乙烯 PVC isomer同分异构物polyvinylfuoride聚氟乙烯 PVF kneader混淆机polyvinylidenechloride聚偏二氯乙烯leveling agent匀涂剂PVDC lubricant润滑剂prepolymer预聚物matched die method配合成形法silicone resin矽树脂mould clamping force锁模力thermoplastic热塑性mould release agent脱模剂thermosetting热固性nozzle喷嘴thermosetting plastic塑胶oriented film取向薄膜unsaturated polyester不饱和聚酯树脂parison吹气成形坏料模具词汇英语翻译 ( 射出成形 )pellet粒料activator活化剂plasticizer可塑剂bag moulding气胎施压成形plunger压料柱塞bonding strength黏合强度porosity孔隙率breathing排气post cure後固化caulking compound填隙料premix预混料cell气孔purging除去cold slug半凝式射出reciprocating screw来去螺杆colorant著色剂resilience回弹性color matching调色resin injection树脂射出法color masterbatch色母料rheology流变学compound 混淆料sheet塑胶片copolymer共聚合体shot 注射cull残料废品shot cycle射出循环cure凝结化slip agent圆滑剂cryptometer 不透明度仪take out device取料装置daylight开隙tie bar拉杆dry cycle time空料试车周期时间toggle type mould clamping system肘杆ductility延性式锁模装置elastomer弹性体torpedo spreader鱼雷形分流板extruded bead sealing压出粒涂层法transparency透明性feed供料void content空洞率filler充填剂模具词汇英语翻译 ( 表面办理 )film blowing薄膜吹制法age hardening时效硬化floating platen活动模板ageing老化办理foaming agent发泡剂air hardening气体硬化gloss光彩air patenting空气韧化granule 颗粒料annealing退火gunk料斗anode effect阳极效应hot mark热斑anodizing阳极氧化办理hot stamping烫印atomloy treatment阿托木洛伊表面injection nozzle射出喷嘴austempering奥氏体等温淬火injection plunger射出柱塞austenite奥斯田体 / 奥氏体injection ram射出冲柱bainite贝氏体banded structure条纹状组织barrel plating滚镀barrel tumbling滚筒打光blackening染黑法blue shortness青熟脆性bonderizing磷酸盐皮膜办理box annealing箱型退火box carburizing封箱渗碳bright electroplating辉面电镀bright heat treatment光芒热办理bypass heat treatment旁路热办理carbide 炭化物carburized case depth浸碳硬化深层carburizing渗碳cementite炭化铁chemical plating化学电镀chemical vapor deposition化学蒸镀coarsening结晶粒粗大化coating 涂布被覆cold shortness低温脆性comemtite渗碳体controlled atmosphere大气热办理corner effect锐角效应creeping discharge蠕缓放电decarburization脱碳办理decarburizing脱碳退火depth of hardening硬化深层diffusion扩散diffusion annealing扩散退火electrolytic hardening电解淬火embossing压花etching表面蚀刻ferrite肥粒铁first stage annealing第一段退火flame hardening火焰硬化flame treatment火焰办理full annealing完整退火gaseous cyaniding气体氧化法globular cementite球状炭化铁grain size结晶粒度granolite treatment磷酸溶液热办理graphitizing石墨退火hardenability硬化性hardenability curve硬化性曲线hardening 硬化heat treatment热办理hot bath quenching热浴淬火hot dipping热浸镀induction hardening高周波硬化ion carbonitriding离子渗碳氮化ion carburizing离子渗碳办理ion plating离子电镀isothermal annealing等温退火liquid honing液体喷砂法low temperature annealing低温退火malleablizing可锻化退火martempering麻回火办理martensite马氏体 / 硬化铁炭metallikon金属喷镀法metallizing真空涂膜nitriding氮化办理nitrocarburizing软氮化normalizing正常化oil quenching油淬化overageing过老化overheating过热pearlite针尖组织phosphating磷酸盐皮膜办理physical vapor deposition物理蒸镀plasma nitriding离子氮化pre-annealing预备退火precipitation析出precipitation hardening析出硬化press quenching加压硬化process annealing制程退火quench ageing淬火老化quench hardening淬火quenching crack淬火裂缝quenching distortion淬火变形quenching stress淬火应力reconditioning再调质recrystallization再结晶red shortness红热脆性residual stress残留应力retained austenite残留奥rust prevention防蚀salt bath quenching盐浴淬火sand blast喷砂办理seasoning 时效办理backing衬垫second stage annealing第二段退火belt sander带式打磨机secular distortion经年变形buffing抛光segregation 偏析chamfering machine倒角机selective hardening部分淬火chamfering tool去角刀具shot blast喷丸办理chisel扁錾shot peening珠击法chuck 夹具single stage nitriding等温渗氮compass 两角规sintering烧结办理concave cutter凹面铣刀soaking均热办理convex cutter凸形铣刀softening融化退火cross joint十字接头solution treatment固熔解热办理cutting edge clearance刃口余隙角spheroidizing球状化退火drill stand钻台stabilizing treatment平定化办理edge file刃用锉刀straightening annealing矫直退火file锉刀strain ageing应变老化flange joint凸缘接头stress relieving annealing应力除去退grinder砂轮机火hammer 铁锤subzero treatment生冷办理hand brace手摇钻supercooling过冷hatching剖面线surface hardening表面硬化办理hexagon headed bolt六角头螺栓temper brittleness回火脆性hexagon nut六角螺帽temper colour回火颜色index head分度头tempering回火jack千斤顶tempering crack回火裂缝jig治具texture咬花kit工具箱thermal refining调质办理lapping研磨thermoechanical treatment加工热办理metal saw金工锯time quenching时间淬火nose angle刀角transformation变态pinchers钳子tufftride process软氮化办理pliers铗钳 plug柱塞头under annealing不完整退火polisher磨光器vacuum carbonitriding真空渗碳氮化protable driller手提钻孔机vacuum carburizing真空渗碳办理punch 冲头vacuum hardening真空淬火sand paper砂纸vacuum heat treatment真空热办理scraper刮刀vacuum nitriding真空氮化screw driver螺丝起子water quenching水淬火scribing划线wetout 浸润办理second out file中纹锉模具词汇英语翻译 ( 模具常用刀具工spanner扳手作法 )spline broach方栓槽拉刀adjustable spanner活动扳手square直角尺angle cutter角铣刀square sleeker方形镘刀arbour心轴square trowel直角度stripping剥离工具T-slot T形槽tool for lathe车刀tool point angle刀刃角tool post刀架tosecan划线盘trimming去毛边waffle die flattening压纹效平wiper脱模钳wrench 螺旋扳手模具词汇英语翻译 ( 冲模加工 ) barreling滚光加工belling压凸加工bending曲折加工blanking下料加工bulging撑压加工burring冲缘加工cam die bending凸轮曲折加工coining压印加工compressing 压缩加工 compression bending 押曲折加工 crowning 凸面加工curl bending肀咄淝庸?curling卷曲加工cutting切削加工dinking切断蕊骨double shearing叠板裁断drawing引伸加工drawing with ironing 抽引圆滑加工embossing 浮花压制加工extrusion挤制加工filing锉削加工fine blanking精细下料加工finish blanking光制下料加工finishing精整加工flanging凸缘加工folding折边曲折加工folding摺叠加工forming成形加工impact extrusion冲击挤压加工indenting压痕加工ironing引缩加工knurling滚花lock seaming固定接合louvering百页窗板加工marking刻印加工necking颈缩加工notching冲口加工parting分断加工piercing冲孔加工progressive bending连续曲折加工progressive blanking连续下料加工progressive drawing连续引伸加工progressive forming连续成形加工reaming铰孔加工restriking二次精冲加工riveting铆接加工roll bending滚筒曲折加工roll finishing滚压加工rolling压延加工roughing粗加工scrapless machining无废料加工seaming折弯重叠加工shaving缺口修整加工shearing切断加工sizing 精压加工 / 改正加工slitting割缝加工spinning卷边 ?接stamping锻压加工swaging挤锻压加工trimming整缘加工upsetting锻粗加工wiring 抽线加工模具词汇英语翻译 ( 冲压机械及周边 ) back shaft支撑轴blank determination胚料睁开bottom slide press下传动式压力机board drop hammer板落锤brake 煞车 buckle剥砂面camlachie cramp 铸包chamotte sand烧磨砂charging hopper加料漏斗clearance空隙closed-die forging合模锻造clump 夹紧clutch 离合器clutch brake离合器制动器clutch boss离合器轮壳clutch lining离合器覆盖coil car带卷起落运输机coil cradle卷材进料装置coil reel stand钢材卷料架column 圆柱connection screw 连杆调理螺钉core compound 砂心黏结剂counter blow hammer对击锻锤cradle送料架crank 曲柄轴crankless无曲柄式cross crank横向曲轴cushion缓冲depression外缩凹孔dial feed分度送料die approach模吵嘴度die assembly合模die cushion模具缓冲垫die height冲压闭合高度die life模具寿命die opening母模逃孔die spotting press调整冲模用压力机double crank press双曲柄轴冲床draght angle逃料倾斜角edging边锻伸embedded core 加装砂心feed length送料长度feed level送料高度filling core埋入砂心filling in填砂film play液面花纹fine blanking press精细下料冲床forging roll辊锻机finishing slag炼後熔渣fly wheel飞轮fly wheel brake飞轮制动器foot press脚踏冲床formboard进模口板frame 床身机架friction摩擦friction brake 摩擦煞车 gapshear 凹口剪床 gear 齿轮gib 滑块指引部gripper 夹具gripper feed夹持进料gripper feeder夹紧传递装置hammer 槌机hand press手动冲床hand rack pinion press手动齿轮齿条式冲床hand screw press手动螺旋式冲床hopper feed料斗送料idle stage空站inching 微调尺寸isothermal forging恒温锻造key clutch键槽离合器knockout 脱模装置knuckle mechanic转向机构land 模具直线刀面部loader 供料器 unloader卸料机loop controller闭回路控制器lower die下模micro inching device微寸动装置microinching equipment微动装置moving bolster活动工作台notching press冲缺口压力机opening 排料逃孔overload protection device防超载装置pinch roll导正滚轮pinion小齿轮pitch节距pressfit压入progressive连续送料pusher feed推杆式送料pusher feeder 料片押片装置quick die change system迅速换模系统regrinding再次研磨releasing松释动作reversed blanking反转下料robot机器人roll forming machine辊轧成形roll forming machine辊轧成形机roll release脱辊roller feed辊式送料roller leveler辊式矫直机rotary bender卷弯成形机safety guard安全保护装置scrap cutter废料切刀scrap press废料冲床seamless forging无缝锻造shave 崩砂shear angle剪角sheet loader薄板装料机shot 单行程工作shrinkage fit缩短配合shut height闭合高度sieve mesh 筛孔sintering of sand铸砂烧贴slide balancer滑动均衡器slug hole逃料孔spin forming machine旋压成形机spotting合模stack feeder堆叠拨送料机stickness黏模性straight side frame冲床侧板stretcher leveler拉伸矫直机strip feeder料材送料装置stripping pressure弹出压力stroke 冲程take out device取料装置toggle press肘杆式压力机transfer feed连续自动送料装置turrent punch press转塔冲床two speed clutch双速离合器uncoiler闭卷送料机unloader卸载机vibration feeder振动送料机wiring press嵌线卷边机模具词汇英语翻译 ( 线切割放电加工关系用语 )abnormal glow不规则辉光放电arc discharge电弧放电belt 皮带centreless没心chrome bronze铭铜clearance angle後角corner shear drop直角压陷deflection桡曲度discharge energy 放电能量dressing 修整dwell保压flange凸缘gap 空隙graphite石墨graphite contraction allowance电极减小余量graphite holder电极夹座hair crack发裂horn 电极臂jump 跳刀magnetic base磁性座master graphite标准电极pipe graphite管状电极pulse脉冲rib working肋部加工roller electrode滚轮式电极rotary surface旋转面shank 柄部sharp edge锐角部tough bronze韧铜traverse摇臂tungsten bronze钨青铜waviness波形起伏working allowance加工余量working dischard加工废料模具有关词汇英语翻译 ( 锻锻造关系用语 )accretion炉瘤acid converter酸性转炉acid lining cupola酸性熔铁炉acid open-hearth furnace酸性平炉aerator 松砂机air set mold常温自硬铸模airless blasting cleaning离心喷光all core molding会合式铸模all round die holder通用模座assembly mark锻造合模记号back pouring补浇注backing sand背砂base bullion粗金属锭base permeability原砂透心胸belling压凸billet坏料bleed 漏铸blocker预锻模膛blocking粗胚锻件blow hole铸件气孔board drop hammer板落锤bottom pour mold底浇bottom pouring底注boxless mold 脱箱砂模break-off core缩颈砂心brick molding砌箱造模法buckle剥砂面camber 错箱camlachie cramp铸包cast blade锻造叶片casting flange锻造凸缘casting on flat水平锻造chamotte sand烧磨砂charging hopper加料漏斗cleaning of casting铸件清理closed-die forging合模锻造core compound砂心黏结剂core template砂心模板core vent砂蕊排气孔corner gate压边浇口counter blow hammer 对击锻造counter lock 止口镶嵌方式depression 外缩凹孔 die approach 模吵嘴度 draw out 锻造拔长 draw plate 起模板 draw spike 起模长针dummying 预锻embedded core 加装砂心erosion冲砂fettling铸件清理filling core埋入砂心filling in填砂film play液面花纹finishing slag炼後熔渣flash gutter锻模飞边槽flask molding砂箱造模forging roll辊锻机formboard进模口板gutter锻模飞边槽hammer man锻工heading machine顶镦机impacter卧式锻造机inblock cast整体锻造ingot 铸锭ingot blank铸坯inlay casting镶铸法investment casting失模锻造isothermal forging恒温锻造loose piece木模活块molding pit铸模地坑pouring process浇注法recasting重铸roll forging轧锻rolled surface轧制表面rough sand 粗砂roughing forge粗锻sand crushing塌箱seamless forging无缝锻造separate分别shave 崩砂shrinkage fit缩短配合shut height闭合高度sieve mesh 筛孔sintering of sand铸砂烧贴slag 熔渣slag inclusion夹渣stickness黏模性strip layout带状胚料排样法tap casting顶注top gate顶注浇口unworked casting不加工铸件upender翻转装置upending顶锻uphill casting底铸white cast iron白口铸件模具词汇有关英语翻译 ( 砂轮用语 ) abrasive砂轮Al2O3 氧化铝borazon氧化硼立方晶buffing wheel抛光布轮diamond 钻石dresser砂轮整修机3-plate mold三板模dressing修整2-plate mold二板模endless grinding belt循环式研磨带leader pin/guide pin边钉/导边finishing allowance加工余量bushing/guide bushing边司/导套grain磨粒shoulder guide bushing中托司grinding disc研磨盘guide pin中托边jamp up孔眼拥塞ejector retainner plate顶针板mesh 网筛目support plate托板resinoid grinding wheel半树脂型砂轮screw螺丝slitting切缝量dowel pin管钉vitrified陶瓷的ply bar scot开模槽模具加工方法词汇的英语翻译core/cavity inter-lock内模管位barrel 滚筒 ( 加工 )ejector pin顶针bending涟漪加工ejector sleeve司筒broaching拉刀切削ejector pin司筒针centering定中心stripper plate推板cutting切削movable core,return core core puller 缩cylindrical lathe cutting外圆车削呵electric discharge machine放电加工nylon latch lock扣机（尼龙拉勾）electrolytic grinding电解研磨lifter斜顶embossing 压花加工mold base模胚（架）facing面车削cavity insert上内模filing锉刀修润core insert下内模hand finishing手工修润slide行位（滑块）hemming 卷边加工insert镶件hobbing滚齿加工wedge 压座 / 斜鸡joggling摇动加工wedge wear plate耐磨板 / 油板lapping抛光 / 研磨修润plate压条laser beam machining雷射加工Lsupport pillar撑头lathe cutting车床车削sprue bushing唧嘴planning刨削加工stop plate挡板polishing抛亮光locating ring定位圈reaming铰孔修润latch锁扣rough machining粗切削parting lock set扣鸡rounding圆形加工push bar推杆sawing锯削栓打螺丝scaling除去钢碇缺点eracuretun顶板shaping成形加工lever arm活动臂skiving表面研磨 slotting切缝切削spure sperader分流锥taper turning锥度车削bush水口司thread cutting螺纹切削stop pin垃圾钉ultrasonic machining超音波加工buffle隔片up cut milling逆铣加工spring rod弹弓柱模具部件英语词汇die spring弹弓ejector guide bush中托司top block上垫脚ejector guide pin中托边punch set上模座pin 镶针punch pad 上垫板dowel pin销子punch holder上夹板ball catch波子弹弓stripper pad脱料背板pipe plug喉塞up stripper上脱料板lock plate锁模块male die公模 (凸模 )angle from pin斜顶feature die公母模angle ejector rod斜顶杆female die母模(凹模 )parting locks尼龙拉勾upper plate上模板lever arm活动臂lower plate下模板early return bar复位键、提早回杆die pad下垫板valves气阀die holder下夹板angle pin斜导边die set下模座terms术语bottom block下垫脚parting surface support balance承压平bottom plate下托板 (底板)面均衡stripping plate内外打 ( 脱料板 ) parting line venting模排气outer stripper外脱料板return pin and cavity interference回inner stripper内脱料板针碰料位lower stripper下脱料板mold base shut hight模总高高出啤机规inner guiding post内导柱格inner hexagon screw内六角螺钉water line interferes withejector pin dowel pin固定销顶针碰运水coil spring弹簧part from cavith (core) side料位出上 /lifter pin顶料销下模eq-height sleeves=spool等高套筒cavity direct cut on A-plate,core direct pin 销cut on B-plate.模胚原身出料位lifter guide pin浮升导料销Do not use (core/cavity) insert禁止用guide pin导正销镶件wire spring圆线弹簧use beryllium copper insert用铍铜做镶outer guiding post外导柱件stop screw止付螺丝preliinary(final)mold design初步（正located pin定位销式）模图设计outer bush外导套reverse core反呵punch冲头spring compressed length弹弓压缩量insert 入块 ( 嵌入件 )good stability,stable稳固性好deburring punch压毛边冲子insufficient rigidity强度不够groove punch压线冲子even cooling平均冷却stamped punch字模冲子sticking扣模round punch圆冲子thero expansion热膨胀special shape punch异形冲子tolorance公差bending block折刀copper electrode铜公 ( 电极）roller滚轴top plate上托板（顶板）baffle plate挡块located block定位块发热管： cartridge heater supporting block for location定位支承探针 : thermocouples块插头： connector plugair cushion plate气垫板插座： connector socketair-cushion eject-rod气垫顶杆密封 / 封料： sealtrimming punch切边冲子三、运水： water linestiffening rib punch = stinger增强筋喉塞： line lpug冲子喉管： tuberibbon punch压筋冲子塑胶管： plastic tubereel-stretch punch卷圆压平冲子迅速接头： jiffy quick connector guide plate定位板plug/sockersliding block滑块四、模具部件： mold components sliding dowel block滑块固定块三板模： 3-plate moldactive plate活动板二板模： 2-plate moldlower sliding plate下滑块板边钉 / 导边： leader pin/guide pin upper holder block上压块边司 / 导套： bushing/guide bushing upper mid plate上中间板中托司： shoulder guide bushing spring box弹簧箱中托边 L： guide pinspring-box eject-rod弹簧箱顶杆顶针板： ejector retainner plate spring-box eject-plate弹簧箱顶板托板： support platebushing bolck衬套螺丝： screwcover plate盖板管钉： dowel pinguide pad导料块开模槽： ply bar scotmold [mEuld] n.模型 , 铸型 vt.浇铸 ,塑内模管位： core/cavity inter-lock造顶针： ejector pintooling [5tu:liN] v.加工司筒： ejector sleeve模具英语专业术语司 _______筒针： ejector pin一、入水： gate推板： stripper plate进入位： gate location缩呵： movable core,return core core 水口形式： gate type puller大水口： edge gate扣机（尼龙拉勾）： nylon latch lock 细水口： pin-point gate斜顶： lifter水口大小： gate size模胚（架）： mold base转水口： switching runner/gate上内模： cavity insert唧嘴口径： sprue diameter下内模： core insert二、流道 : runner行位（滑块）： slide热流道： hot runner,hot manifold镶件： insert热嘴冷流道 : hot sprue/cold runner压座 / 斜鸡： wedge唧嘴直流 : direct sprue gate耐磨板 / 油板： wedge wear plate圆形流道： round(full/half runner压条： plate流道电脑剖析： mold flow analysis撑头 : support pillar流道均衡 :runner balance唧嘴： sprue bushing热嘴： hot sprue挡板： stop plate热流道板： hot manifold定位圈： locating ring。

（完整版）冲压模具公司专用英文词汇

（完整版）冲压模具公司专用英文词汇公司英語: 常用術語Technology and Development Committee 技術發展委員會 BS Brain Storming 腦力激蕩QCC Quality Control Circle 品質圈PDCAPlan Do Check ActionDCC delivery control center 交貨管制中心3CComputer 電腦類產品Consumer electronics 消費性電子產品 Communication 通訊類產品Core value （核心价值）Love 愛心 Confidence 信心 Decision 決心教育訓練部沖模一廠沖模二廠樣品中心Stamping tool shop I Stamping tool shop II Prototype workshop Steel factory PCE molding tooling workshop PCE 裁剪廠Hua Nan test and measurement center MPE mobile phone enclosure MPE MBE mobile phone and notebook enclosure MGE Alloy magnesium alloy enclosure Engineer standard 工標 Document center （database center ）資料中心 Design Center 設計中心烤漆（廠） Assembly 沖壓（廠）塑模廠華南檢測中心明塑厂鎂合金Painting Stamping Education and Training 教育訓練proposal improvement/creative suggestion Technological exchange and study組裝（廠）提案改善技術交流研習會計劃執行檢查總結Corporate culture( 公司文化) Integration 融合Responsibility責任Progress 進步3T STRATEGYTime to market Time to volume Time to money 及時切入生產及時大量生產及時大量交貨Engineering control system 工程管制系統Quality control system 品質管制系統Manufacturing control system 生產管制系統Management control system 經營管制系統7SClassificati on 整理(sort ing, orga ni zati on)-seiri Regulation 整頓(arrangement, tidiness)-seiton Cleanliness 清掃(sweeping, purity)-seiso Conservation 清洁(cleaning, cleanliness)-seiktsu Culture 教養(discipline)-shitsukeSave 節約Safety 安全: 英文縮寫品質人員名稱類QC quality control 品質管理人員FQC final quality control 終點品質管制人員IPQC in process quality control 制程中的品質管制人員OQC output quality control 最終出貨品質管制人員IQC incoming quality control 進料品質管制人員TQC total quality control 全面質量管理POC passage quality control 段檢人員QA quality assurance 質量保證人員OQA output quality assurance 出貨質量保證人員FOUR CONTROL YST 大管制系統QE quality engineering 品質工程人員品質保證類FAI first article inspection 新品首件檢查FAA first article assurance 首件確認CP capability index 能力指數CPK capability process index 模具製程能力參數SSQA standardized supplier quality audit 合格供應商品質評估FMEA failure model effectiveness analysis 失效模式分析FQC S作類AQL Acceptable Quality Level 運作類允收品質水準S/S Sample size 抽樣檢驗樣本大小ACC Accept 允收REE Reject 拒收CR Critical 極嚴重的MAJ Major 主要的MIN Minor 輕微的Q/R/S Quality/Reliability/Service 品質/ 可靠度/ 服務P/N Part Number 料號L/N Lot Number 批號AOD Accept On Deviation 特采UAI Use As It 特采FPIR First Piece Inspection Report 首件檢查報告百萬分之一PPM Percent Per Million制程統計品管專類SPC Statistical Process Control 統計製程管制SQC Statistical Quality Control 統計品質管制GRR Gauge Reproductiveness & Repeatability 量具之再制性及重測性判斷量可靠與否DIM Dimension 尺寸DIA Diameter 直徑N Number 樣品數其它品質術語類QIT Quality Improvement Team 品質改善小組ZD Zero Defect 零缺點QI Quality Improvement 品質改善QP Quality Policy 目標方針TQM T otal Quality Management 全面品質管理RMA Return Material Audit 退料認可7QCT ools 7 Quality Control T ools 品管七大手法通用之件類ECN Engineering Change Notice 工程變更通知（供應商）ECO Engineering Change Order 工程改動要求（客戶）PCN Process Change Notice 工序改動通知PMP Product Management Plan 生產管制計劃SIP Standard Inspection Procedure 製程檢驗標準程序SOP Standard Operation Procedure 製造作業規範IS Inspection Specification 成品檢驗規範BOM Bill Of Material 物料清單PS Package Specification 包裝規範SPEC Specification 規格DWG Drawing 圖面系統文件類ES Engineering Standard 工程標準CGOO China General PCE龍華廠文件IWS International Workman Standard 工藝標準ISO International Standard Organization 國際標準化組織GS General Specification 一般規格部類PMC Production & Material Control 生產和物料控制PCC Product control center 生產管制中心PPC Production Plan Control 生產計劃控制MC Material Control 物料控制DC Document Center 資料中心QE Quality Engineering 品質工程（部）QA Quality Assurance 品質保證（處）QC Quality Control 品質管制（課）PD Product Department 生產部LAB Laboratory 實驗室IE Industrial Engineering 工業工程R&D Research & Design 設計開發部生產類PCs Pieces 個（根, 塊等）PRS Pairs 雙（對等）CTN Carton 卡通箱PAL Pallet/skid 棧板PO Purchasing Order 采購訂單MO Manufacture Order 生產單D/C Date Code 生產日期碼ID/C Identification Code （供應商）識別碼SWR Special Work Request 特殊工作需求L/N Lot Number 批號P/N Part Number 料號OEM Original Equipment Manufacture 原設備製造PC Personal Computer 個人電腦CPU Central Processing Unit 中央處理器A.S.A.P As Soon As Possible 盡可能快的E-MAIL Electrical-Mail 電子郵件N/A Not Applicable 不適用QTY Quantity 數量I/O input/output 輸入/ 輸出NG Not Good 不行, 不合格C=0 Critical=0 極嚴重不允許APP Approve 核準, 認可, 承認CHK Check 確認ASS'Y Assembly 裝配, 組裝T/P True Position 真位度5WIH When, Where, Who, What, Why, How to6M Man, Machine, Material, Method, Measurement, Message4MTH Man, Material, Money, Method, Time, How 人力, 物力,財務, 技術, 時間（資源）SQA Strategy Quality Assurance 策略品質保證DQA Design Quality Assurance 設計品質保證MQA Manufacture Quality Assurance 製造品質保證SSQA Sales and service Quality Assurance 銷售及服務品質保證LRR Lot Reject Rate 批退率SPS Switching power supply 電源箱DT Desk Top 臥式（機箱）MT Mini-Tower 立式（機箱）DVD Digital Video DiskVCD Video Compact DiskLCD Liquid Crystal DisplayCAD Computer Aided DesignCAM Computer Aided ManufacturingCAE Computer Aided EngineeringPCB Printed Circuit Board 印刷電路板CAR Correction Action Report 改善報告NG Not Good 不良WDR Weekly Delivery Requirement 周出貨要求PPM Percent Per Million 百萬分之一TPM Total Production Maintenance 全面生產保養MRP Material Requirement Planning 物料需計劃OS Operation System 作業系統TBA To Be Assured 待定, 定缺D/C Drawing ChangeP/P Plans & ProcedureEMI Electrical-Music Industry 電子音樂工業Electrical Magnetic Interference 電子干扰RFI Read Frequency Input 讀頻輸入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material SizeLED lighting-emitting diode 發光二极管QBR Quarter Business RecordCIP Continuous improvement processFGI Forecasted Goal InventoryCNC Computerized numeral controllerB2C Business to customerB2B Business to businessAVL Approved vendor listPOP Procedure of packagingEOL End of lifeVDCS Vender defect correcting sheetPDCS Process defect correcting sheetGRN Goods receiving noteA/R Accounting receivableA/P Accounting payable專業詞匯deputy supervisor =vice supervisor 副課長group leader 組長line leader 線長supervisor 課長responsible department 負責單位Human Resources Department 人力資源部Head count 人頭數production department 生產部門planning department 企劃部QC Section 品管課通用類president 董事長operator 作業員position 職務general manager 總經理special assistant 特助deputy manager |'depjuti| =vice manager 副理stampi ng factory 沖壓廠pain ti ng factory 烤漆廠moldi ng factory 成型廠admi nistrati on/gen eral affairs dept./ 總務部producti on un it生產單位meeting minutes 會議記錄distributi on departme nt 分發單位subject 主題conclusion 結論decisi on items 決議事項pre-fixed fini shi ng date 預定完成日Color man ageme nt 顏色管理Visual man ageme nt 目視管理producti on capacity 生產力first count 初盤first check 初盤復櫂second count 復盤second check復盤復核qua ntity of physical inventory second count 復盤點數量physical inventory 盤點數量physical count qua ntity 帳面數量differe nee qua ntity 差異量spare parts physical inven tory list 備品盤點清單cause an alysis 原因分析waste materials 廢料descripti on 品名specificati on 規格model機種work order 工令revisio n 版次remark 備注registration 登記registrati on card 登記卡to con trol 管希9 consume, consumption 消耗p notify 通知to fill in 填寫to collect, to gather 收集statistics 統計cosmetic in specti on sta ndard外觀檢驗規範computer case 電腦外殼(組件)personal computer enclosure 電腦機箱產品front plate 前板fearplate 后板chassis |' /?si| 基座bezel pan el 面板Hood 上蓋base pan 基座bezel 面板risercard 擴充卡flat cable 排線TOP driver cage 上磁架bottomdriver cage 下磁架resi n film樹脂膜(■aw materials 原料materials物料a teel plate 鋼板P oll/coil material 捲料e pare parts =buffer 備品plastic parts 塑膠件sheet metalparts/stamp ing parts 沖件material check list 物料檢查表fini shed product 成品semi-fi ni shed product 半成品good product/accepted goods/ accepted parts/good parts 良品defective product/non-good parts不良品disposed goods 處理品warehouse/hub 倉庫pack ing material 包材basket蝴蝶竺plastic basket 膠筐flow chart 流程表單producti on tempo 生產進度現狀lots of producti on 生產批量to revise, modify 修訂to switch over to, switch ——to, switch ing over 切換engin eeri ng bottle neck, project difficulty 工程瓶頸glove(s)手套gBand-Aid創可貼i ndustrial alcohol 工業酒精broom掃扌巴mop拖扌巴vacuum cleaner 吸塵器s ag抹布garbage container 灰箕garbage can 垃圾箱w arbage bag 垃圾袋i iais on 聯絡單rags抹布h amp holder 燈架to mop the floor 拖地to clea n a table 擦桌子air pipe 氣管p elivery deadli ne 交貨期die worker 模工producti on, toproduce 生產 e d。

五金模具及冲压专业英语

連續模progressive die
複合模gang dies
剪邊模shearing die
鉚合模riveting die
沖孔pierce
成型(抽凸,沖凸)forming
抽孔draw hole
折彎bending
切邊trim
凸點emboss
凸圓dome
半剪semi-shearing
沖記號stamp mark
氣墊板air cushion plate
氣墊頂桿air-cushion eject-rod
切邊沖子trimming punch
加強筋衝子stiffening rib punch = stinger
壓筋沖子ribbon punch
卷圓壓平沖子reel-stretch punch
定位板guide plate
展開圖extension dwg
工程圖procedure dwg
模具結構圖die structure dwg
料片厚度material thickness
系數factor
向上upward
向下downward
沖床規格press specification
適用模高die height range
閉模高度die height
凹模die
止付螺絲screw plug
限位塊stroke end block
浮升導料銷guide lifter pin
脫料板stripper plate
導柱guide post
導套guide bushing
有珠導柱ball bearing guide post
沖子punch
入子（鑲塊）insert
頂桿eject rod

模具英语词汇大全

模具英语词汇大全-CAL-FENGHAI.-(YICAI)-Company One1汽车冲压模具英语词汇Die / Tool= 模具Prog. Die=progressive die 级进模Ball bearing guide posts and bushings=球形滚珠导柱和轴套Casting die=铸造模Cage=套Part=钣件Rigidity=强度Die material=制模材料Thin=薄Tool design=模具设计Strip design=料条设计Using material thickness radii where sharp corners are shown on the part reduces the occurrence of chipped punch or die corners in the tool. =在尖角处使用与材料厚度一样的R角减少冲头碎裂或模具中有“刀口”Tool design approval=模具设计审核Tool design modification/revision=模具设计更改Tool parts design (detail) =模具钣件设计（详细）Heeled die sets, internally heel form & trim sections=带箱根的模架，成形与切刃冲头带导引FMC Make=保丽龙制作Construction method=结构方法modification= 更改Check & measure=检查 & 测试Machining= 机器加工Large machining=在大型机器上加工上下模架（铣、车等）Small machining=在小型机器上加工模块等Lower die trim inserts=下模切刃块Lower trim inserts retainer=下模切刃块承盘Assemble inserts=组立镶块Punch stripping plates=冲头压料板Assembly=组立Trim punch backing plates=切刃冲头背板NC Machining=NC雕刻加工Stripper window inserts=料条窗户镶块Fitting=研磨组立Spotting=合模Die tryout=试模Cushing stroke=缓冲行程Dowel pin=定位销Guide lift pin=导引升降销Assemble gas spring=安装氮气缸Stamp parts=冲钣件Adjustment=调试Run off parts=冲钣件Lower trim steels=下刃块Hit parts=冲钣件Section=冲头断面Lifters=提升器Trim punch=切刃冲头Coil=卷材jack screw hole=起重[千斤顶]螺旋孔Guide block=导引块Die set, lower plate=下模架Guide the coil through the tool=导引卷材Die set, upper plate=上模架layout inspection=全尺寸检验Die inspection & approval=模具检查和审核Stretch carriers=拉伸运送装置delivery=发货Punch stripping plates=冲头压料板Rejected=拒收Trim punch backing plates=切刃冲头背板Scrapped=报废Stripper window inserts=料条窗户镶块Rework=返工Heel plates=背托stop block=停止块Prepare for delivery=准备发货Hydro form 液压成形Key=键Shear=剪切For locating retainer blocks=承盘键Sensor=传感器For holding buttons or pilots=冲母座或导销键Stretch web=拉伸网For fixed heel or positive stop=镶根键Layout the parts=设计钣件Construction method=结构方法Preceding into the design=继续设计Manual Surface Grinder=手动平面磨床Guide the coil through the tool=导引卷材Spotting red=合模用丹红Checking aid /checking gage=检具Layout ink=试模用蓝墨水Jig=夹具Masking tape=黄色不透明胶带(遮蔽胶带) Fixture=夹具Pliers=尖嘴钳，老虎钳Ball bearing guide posts and bushings=球形滚珠轴套Cresent wrench=可调扳手Guide post=导柱Bushings=导套Pump pipe=泵管Using material thickness radii where sharp corners are shown on the part reduces the occurrence of chipped punch or die corners in the tool. =在尖角处使用与材料厚度一样的R 角减少冲头碎裂或模具中有“刀口”CMM=三次元测量仪Symmetric=对称的The axis of symmetry=对称轴Technical=技术上的Diagonal=对角线Heeled die sets, internally heel form & trim sections=带箱根的模架，成形与切刃冲头带导引One two three block=一二三模块Adjustable parallels=可调平行块Stop block=阻止块Granite Table=花岗岩平台Backing Plate=背板Plotter= .描绘器, 图形显示器, 绘图器, 坐标自记器, 标图员Shoulder Bolt=肩头螺丝(Stripper bolt)Belt Sander=带磨机Keeper Block=行程块Metal Cutting Band Saw=立式带锯床Corner Guide Block=导块Blanchard Grinder=大型平面磨床Dowel pin=定位销Joe Blocks=精密量块Set Screw=螺塞Whirly Gig=筒夹式冲子成形器Jig & fixture =夹具Chamfer Tools=倒角刀具组Checking fixture=检具Angle Plate=L形直角座Guide Block=导块Gage Pins=英寸塞规Plunger=柱塞Sine Plate (magnetic)=正弦磁台Pierce=冲孔Flute End Mill=硬质合金钢铣刀Wear Strip=耐磨板Mill Cutter=波纹粗铣刀（标准型）Mating area=组立的接触面C’bore/ counter bore=六角沉头铣刀Accommodate=适应Radius Dresser=砂轮修整器Wiping hard (very shiny)= 过分摩擦闭合[接触]（闪光）Boring Head & Boring Bar=搪孔器、搪刀杆Pin=销Increase the die clearance between the form steels=增加成形块间隙Reamer=绞刀Clearance=间隙Approval=确认Oil paper=油纸Impact wrench=气动扳手0-11” Micrometer=0-11”千分尺Air pin=空气销Trim line=切边bumper[‘bQmpE(r)] n.缓冲器+/-0.5mm unless otherwise specified 除非另有规定，否则公差为+/-0.5mmVendor [‘vendE(r), -dC:(r)] n.卖主Part tolerance=钣件公差stripper layout=排样图Ball nose=球刀drawing of panel #987415&16=钣件设计图（公差）Bore=镗Line tap=攻丝校直Arbor =柄轴；心轴Borer=镗刀，镗床Drill chuck=钻夹头Chamfer=倒角Button=冲母座Radius=半径Nitrogen Cylinder=氮气缸Coolant=切削液Pilot=导销Punch=冲头Retainer=承盘Distribution Blocks=接头座Button=冲母座Screw=螺丝Hose Straps=软管夹（塑料）Shop=车间Flat Feet Keepers=顶料销Crib=仓库Ejector Pin=顶出销CNC mill= CNC机床Spring=弹簧Jack=千斤顶Straight Port Adapter=直管接头Strips=料条Y-205 Hose=软管（塑料）Styrofoam [`stairEfEum]n.聚苯乙烯泡沫塑料（保丽龙材料）Short Neck Adapter=短接头Cut off=落料45。

模具-冲压及工序英语用语

组装、冲压、喷漆等专业词汇Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试V oltage switch of SPS电源电压接拉键sheet metal parts 冲件plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource department人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |'plein|刨床miller铣床grinder磨床driller??床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice sectionsuperisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dein|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓name of a department部门名称administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头sweeper扫把mop拖把vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机production line流水线chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小)cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screwthread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程die repair模修enterprise plan = enterprise expansionprojects企划QC品管die worker模工production, to produce生产equipment设备to start a press开机stop/switch off a press关机classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-gradeproducts良品defective products, not up-to-gradeproducts不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱die change 换模to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material,to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---to throw--over switching over切换engineering, project difficulty工程瓶颈stage die工程模automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊vocabulary for stamping冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, blockstop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑common vocabulary for dieengineering模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physical invetory second count 复盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accounting department for reference会计部存查end-user/using unit(department)使用单位summary of year-end physical inventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records of year-end physical inventory List andphysical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedulesheetPCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory differenceanalysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ acceptedparts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mm welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣品质人员名称类QC quality control 品质管理人员FQC final quality control 终点品质管制人员IPQC in process quality control制程中的品质管制人员OQC output quality control 最终出货品质管制人员IQC incoming quality control 进料品质管制人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 品质工程人员品质保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认TVR tool verification report 模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process 模具制程能力参数SSQA standardized supplier quality合格供应商品质评估OOBA out of box audit 开箱检查QFD quality function deployment品质机能展开FMEA failure model effectivenessanalysis 失效模式分析8 disciplines 8项回复内容FA final audit 最後一次稽核CAR corrective action request 改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level 运作类允收品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂品质AOQL Average Output Quality Level 平均出厂品质Q/R/S Quality/Reliability/Service 品质/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV 特殊抽样水准等级P/N Part Number 料号L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件检查报告FPIR First Piece Inspection Report 百万分之一PPM Percent Per Million 批号制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计品质管制R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR Gauge Reproducibility&Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team 品质改善小组PDCA Plan Do Check Action 计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement 品质改善QP Quality Policy 目标方针TQM Total Quality Management全面品质管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低品质水准RMA Return Material Audit 退料认可QAN Quality Amelionrate Notice品质改善活动ADM Absolute DimensionMeasuremat 全尺寸测量QT Quality Target 品质目标7QCTools 7 Quality Controll Tools品管七大手法通用之件类ECN Engineering Change Notes 工程变更通知(供应商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP Standard Operation Procedure制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 品质系统ES Engineering Standarization 工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWS International WorkmanStandard 工艺标准ISO International StandardOrganization 国际标准化组织GS General Specification 一般规格CMCS C-China M-ManufactC-Compaq S-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-Quality A-AssemblyCompaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类PMC Production & MaterialControl 生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manafacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部P/A Personal & Administration 人事行政部DC Document Center 资料中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证(处)QC Quality Control 品质管制(课) PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供应商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM Original Equipment Manufacture 原设备制造PCE Personal Computer Enclosure 个人电脑外设PC Personal Computer 个人电脑CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China中国大陆U.S.A the United States of America美国A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存I/O Input/Output 输入/输出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-static Discharge 静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact Disk Read-OnlyMemory 只读光碟FDD Floppy Disk Drive 软碟机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CA V Cavity 模穴CAD Computer Aid Design 计算机辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requitement周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间)S/T Standard Time 标准时间P/M Product Market 产品市场3CComputer,Commumcation,Consumerelectronic's 消费性电子5WIHWhen,Where,Who,What,Why,How to5MMan,Machine,Material,Method,Measurement4MIHMan,Materia,Money,Method,Time人力,物力,财务,技术,时间(资源)SQA Strategy Quality Assurance策略品质保证DQA Desigh Quality Assurance 设计品质保证MQA Manufacture QualityAssurance 制造品质保证SSQA Sales and service QualityAssurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect高磁测试FMI Frequency Modulatim Inspect高频测试B/M Boar/Molding(flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Achanced Basic input/output system 先进的基本输入/输出系统CMOS Complemeruary Metoll Oxide Semiconductor 互补金属氧化物半导体PDA Personal Digital Assistant 个人数字助理IC Integrated Circuit 集成电路ISA Industry Standard Architecture 工业标准体制结构MCA Micro Channel Architecture 微通道结构EISA Extended Industry Standard Architecture 扩充的工业标准结构SIMM Single in-line memory module 单项导通汇流组件DIMM Dual in-line Memory Module 双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectivenes 失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 排线PCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WPR Weekly Delivery Requirement 周出货要求PPM Parts Per Million 百万分之一TPM Total Production Maintenance全面生产保养MRP Material Requiremcnt Planning物料需计划OC Operation System 作业系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material Size模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotaryforging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shellcasting 壳模铸造foam forming ?泡成形sinter forging烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slushmolding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warmforging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matchedmould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landed plungermold 有肩柱塞式模具burnishing die 挤光模landed positivemold 有肩全压式模具button die 镶入式圆形凹模loadingshoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold活动式模具clod hobbing 冷挤压制模louveringdie 百叶窗冲切模composite dies 复合模具manifolddie 分歧管模具counter punch 反凸模modular mold组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bendingdie 双折冷弯模具extrusion die 挤出模palletizing die叠层模family mold 反套制品模具plastermold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoketype die 轭型模模具厂常用之标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴托板centerpin 中心梢clamping block 锁定块coil spring螺旋弹簧cold punched nut 冷冲螺母coolingspiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejectorleader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘?flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧?goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶?冲头headless punch直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram压射柱塞inlay busher 嵌入衬套inner plunger内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶?lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locatingring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block歧管档块。

冲压模具专业英语

精品文档冲压模具专业术语英汉对照目录模具厂常用之标准零配件■二，—k? 四，五, 六，七, 八，九, 模具钢材组装、冲压、喷漆等专业词汇模具工程常用词汇模具零件类质量人员名称类系统文件类模具技术用语各式模具分类用语模具常用之工作机械设备十一，表面处理关连用语十二，成形不良用语十三，各种冲模加工关连用语十四，模具常用刀具与工作法用语十五，冲压机械及周边关连用语十六，线切割放电加工关连用语十七，模具加工方法十八，机械设计及周边其它用语一•模具厂常用之标准零配件air vent vale 通气阀anchor pint锚梢angular pin角梢/倾斜梢baffle调节阻板baffle plate （折流）檔板ball button球塞套ball plunger定位球塞ball slider 球塞滑块binder plate压板bla nk holder防皱压板bla nking die落料冲头bolste垫板，上下范本bottom boarc浇注底板bottom plate下固定板brackt支架托架bumper block缓冲块buster 堵口casting ladle浇注包casting lug铸耳cavity 模穴（模仁） cavity retainer plate模穴托板cen ter pin 中心梢clamping block锁定块coil spring 螺旋弹簧cold pun ched nut冷冲螺母cooli ng spiral螺旋冷却栓core 心型core pin心型梢cotter开口梢cross 十字接头cushion pin缓冲梢diaphragm gate盘形浇口die即proach模头料道die bed型底die block块形模体die body铸模座die bush合模衬套die button冲中模母模die clamper夹模器die fastener模具固定用零件die holder 母模固定板die lip模唇die plate冲范本die set下/冲压模座direct gate直接浇口dog chuck爪牙夹头dowel hole销钉孔dozzle辅助浇口dowel （pin）定位洽模梢draft拔模锥度draw bead张力调整杆drive beari ng传动轴承ejection pad顶出衬垫ejector脱模器stripper bol脱料螺栓ejector guide pir顶出导梢ejector leader bushe顶出导梢衬套ejector pad/pin/plate/rod/sleeve/ va顶出垫/梢/板/杆/衬套/阀eye bolt环首螺栓filling core椿入蕊film gate薄膜浇口finger pin指形梢finish mach ined plate角形模板finish mach ined round plat 圆形模板fixed bolster plate固定侧模板flanged pin带凸缘？flash gate毛边形浇口flask上箱floating punch 浮动冲头gate 浇口gate land浇口面gib凹形拉紧/楔goose n eck鹅颈管guide pin/ plate/ bush ing/ post/ 导梢/板/ 轨/衬套/柱head punch 冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose n ippler 管接头impact dampe缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plun gei内柱塞inner punch内冲头insert 嵌件insert /retainer pin嵌件梢king pin转向梢king pin bush主梢衬套kn ockout ba脱模杵land合模平坦面land area合模面leader bushe导梢衬套lifti ng pin起模梢lining内衬locating center punch定位中心冲头locat ing pilot pin定位导梢locat ing ring 定位环lock block压块locking block定位块locking plate定位板loose bush活动衬套mak ing die打印冲子ma nifold block歧管檔块plate衬板master plate靠模样板match plate分型板mold base塑料模座mold clamp铸模紧固夹mold plate n 模用板moving bolste换模保持装置moving bolster plate可动侧范本one piece casti ng 整体铸件parallel block 平行垫块parti ng line 分模线parting lock set合模定位器pass guide穴型导板peened head punc镶入式冲头pilot pin导梢pin gate针尖浇口pre extrusion punc顶挤冲头punch冲头puncher 推杆pusher pin衬套梢rack 机/料架rapping rod起模杆re-entrant mold凹入模retainer plate 托料return pin 回位梢riding stripper浮动脱模器ring gate环型浇口roller滚筒runner/ shoot 流道runner ejector set流道顶出器runner lock pin 流道拉梢screw plug头塞set screw 固定螺丝shedder脱模装置shim垫片shoe模座之上下范本shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide/ram 滑块slip joint滑配接头spacer block间隔块spacer ring间隔环spider模蕊支架spindle 主车由sprue 注道sprue bush ing 注道衬套sprue bush ing guide注道导套sprue lock bushing注道定位衬套sprue puller注道拉料?spue line 合模线square key 方键square nut 方螺帽square thread方螺纹stop collar限位套stop pin止动梢stop ring止动环stopper定位停止梢straight pi n 圆柱梢stripper bush ing脱模衬套stripper plate剥料板stroke end block行程止梢submari ne gate潜入式浇口support pillar支撑柱/顶出支柱support pin支撑梢supporting plate托板sweep templete造模刮板tab gate辅助浇口taper key推拔键taper pin拔锥梢/!隹形梢teeming浇注three start screw三条螺纹thrust pin 推力销tie bar拉杵tunnel gate隧道形浇口vent通气孔wortle plate拉丝范本•模具钢材alloy tool steel 合金工具钢aluminium alloys合金beari ng alloy轴承合金blister steel 浸碳钢bon derized steel sheets 德防蚀钢板carb on tool stee碳素工具钢clad sheet 被覆板clod work die steel冷锻模用钢emery金钢砂ferrostatic pressure冈铁水静压力forging die stee锻造模用钢galvanized steel shee镀锌铁板hard alloy steel超硬合金钢high speed tool stee高速度工具钢hot work die stee热锻模用钢low alloy tool stee特殊工具钢low manganese casting stee低锰铸钢marging stee马式体高强度热处理钢martrix alloy马特里斯合金meeha nite cast iron米汉纟纳铸钢meehanite metal米汉纟纳铁merchant iron市售钢材molybdenum high speed ste钼系高速钢molybdenum steel 钼钢nickel chromium stee镍铬辛冈prehardened stee顶硬钢silic on steel sheet硅钢板sta ini ess steel 不锈钢tin plated steel shee镀锡铁板tough pitch coppe韧铜troostite 吐粒散铁tungsten stee钨钢vinyl tapped steel sheet塑料覆面钢板三.组装、冲压、喷漆等专业词汇Assembly lin组装线Layout布置图Conveye传送带Rivet table 拉钉机Rivet gun拉钉枪Screw drivei起子Electric screw drive 电动起子Pn eumatic screw drive气动起子worktable工作桌OOBA开箱检查fit togethe组装在一起fasten锁紧（螺丝）palle栈板barcode scanne条形码扫描仪fuse togethe熔合fuse machin热熔机operator作业员MT制造生技cosmetic in spec外观检查inner parts in spec内咅B检查thumb screw大头螺丝lbs. i nch英镑、英寸EMI gaske导电条front / rear plate前/后板chassis 基座/底盘bezel panel 面板power butt on/wir电源按键/线reset button复位/重置键Hi-pot test of SPSt源高压测试Voltage switch of SP 电源电压接拉键sheet metal parts 中件plastic parts塑料件SOP制造作业程序material check lis物料检查表work cell 工作间trolley 台车sub-line支线fork truck叉车planning departmen企划咅B QC Section品管科stamping factor冲压厂painting factory烤漆厂molding factory 成型厂com mon equipmen常用设备un coiler and straighte ne整平机punching machind中床robot/transfer机械手hydraulic machind由压机lathe车床planer 包U床miller, driller 铳床grin der磨床铳床wire cutti n线切割electrical sparkl 电火花welde电焊机staker=revit ing machin铆合机preside nt 董事长special assista nt man age特助factory direct。

冲压模具专业词汇知识中英文翻译

冲压模具词汇Counter bored hole 沉孔Chamfer 倒斜角Fillet 倒圆角padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder活页夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerization装箱quantity of physical inventory second count 复盘点数量Quantity of customs count 会计师盘,点数量the first page第一联filed by accounting department for reference会计部存查end-user/using unit(department)使用单位Summary of year-end physical inventory bills 年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO. 空白与作废单号plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet 物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheetPCE组装厂生产排配表model机钟work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门Stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂（degrease）main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条形码flow chart流程窗体assembly组装stamping冲压molding成型 spare parts=buffer备品coordinate坐标dismantle the die折模auxiliary function辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾deducting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave 凹convex凸short射料不足nick缺口speck瑕疪shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill钻boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴angle offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板punch冲头insert入块(嵌入件) deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location 定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模全球模具网die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘?flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶?lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块汽车英语first gear 一档second gear 二档reverse 倒车档two-stroke engine 二冲程发动机diesel 柴油机limousine 豪华轿车drophead 活动车篷汽车(美作:convertible)racing car 赛车saloon 轿车(美作:sedan)wecker, beat-up car, jalopy 老爷车notchback 客货两用车four-wheel drive 四轮驱动front-wheel drive 前轮驱动trailer 拖车truck 卡车compact car 小型汽车light-van 小型货车front wheel 前轮rear wheel 后轮tread 轮距chassis 底盘bodywork, body 车身rear window 后窗玻璃windscreen 挡风玻璃(美作:windshield)windscreen wiper 风档刮水器,风档雨雪刷(美作:windshield wiper) fender, wing, mudguard 挡泥板radiator grille 水箱wing mirror 后视镜bonnet 发动机盖(美作:hood)boot 行李箱(美作:trunk)roof rack, luggage rack 行李架license plate, number plate 车号牌wing 前翼子板hubcap 轮毂罩bumper 保险杠front blinker 前信号灯taillight, tail lamp 尾灯backup light, reversing light 倒车灯stoplight, stop lamp 刹车灯rear blinker 转弯指示灯trunk, boot 行李箱bumper 保险杠tailpipe 排气管back seat, rear seat 后座driver's seat, driving seat 驾驶席passenger seat 旅客席steering wheel, wheel 方向盘rear-view mirror, driving mirror 后视镜horn, hooter 喇叭choke 熄火装置gear stick, gear change 变速杆(美作:gearshift) gearbox 变速箱starter, self-starter 起动器,起动钮brake pedal 刹车踏板clutch pedal 离合器踏板hand brake 手制动器foot brake 脚制动器dashboard 仪表板milometer 里程表speedometer, clock 速度表transmission 传动piston 活塞radiator 散热器fan belt 风扇皮带shaft 传动轴inner tube 内胎drain tap 排气阀门silencer 消音器(美作:muffler)tank 油箱overflow 溢流孔valve 阀门exhaust pipe 排气管spare wheel 备胎,备用轮胎carburettor 汽化器(美化:carburetor) electrical system, wiring 电气系统lights 灯光headlight 大灯,头灯dipped headlight 近光灯rear lights 尾灯sidelights, parking lights 位置灯,边灯direction indicator 方向标,转向标indicator, blinker 方向指示灯sparking plug 火花塞(美作:spark plug)(spare) battery (备用)蓄电池to accelerate 加速to brake 制动,刹车to engage the clutch 接上离合器to declutch 分开离合器to stall 发动机停转to change gear 变速to decelerate 减速top speed 最高速度speed limit 速度限制to park 停车to switch off the motor 熄火模具工程常用词汇模具钢材alloy tool steel 合金工具钢 aluminium alloy 铝合金钢 bearing alloy 轴承合金 blister steel 浸碳钢 bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂 ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel钼系高速钢 molybdenum steel钼钢 nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 硅钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑料覆面钢板四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝： screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）： mold base上内模：cavity insert下内模：core insert行位（滑块）： slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴： sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate. 不准用镶件：Do not use (core/cavity) insert用铍铜做镶件：use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrode模具工程常用词汇die 模具die shoe 模瓦figure file, chart file图档cutting die, blanking die冲模progressive die, follow (-on)die 连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点incoming material to be inspected进货待验PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次production control confirmation生产确认checked by初审approved by核准stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工cause description原因说明part number/ P/N 料号item/group/class类别prepared by制year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单 spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕疵shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft 曲柄augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant 冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies 复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙punch wt.上模重量。

冲压模具专业英语

冲压模具专业英语冲压模具专业术语英汉对照目录一，模具厂常用之标准零配件二，模具钢材三，组装、冲压、喷漆等专业词汇四，模具工程常用词汇五，模具零件类六，质量人员名称类七，系统文件类八，模具技术用语九，各式模具分类用语十，模具常用之工作机械设备十一，表面处理关连用语十二，成形不良用语十三，各种冲模加工关连用语十四，模具常用刀具与工作法用语十五，冲压机械及周边关连用语十六，线切割放电加工关连用语十七，模具加工方法十八，机械设计及周边其它用语一．模具厂常用之标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢/倾斜梢baffle 调节阻板baffle plate （折流）檔板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster垫板，上下范本bottom board 浇注底板bottom plate 下固定板brackt支架托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲范本die set 下/冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel hole 销钉孔dozzle 辅助浇口dowel （pin）定位/合模梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器stripper bolt 脱料螺栓ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad /pin/plate/rod/sleeve/ valve顶出垫/梢/板/杆/衬套/阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘?flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧/楔goose neck 鹅颈管guide pin/ plate/ bushing/ post/ rail导梢/板/轨/衬套/柱head punch 冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert /retainer pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模梢lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管檔块plate 衬板master plate 靠模样板match plate 分型板mold base 塑料模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧范本one piece casting 整体铸件parallel block 平行垫块parting line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导梢pin gate 针尖浇口pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机/料架rapping rod 起模杆re-entrant mold 凹入模retainer plate 托料return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口roller 滚筒runner/ shoot 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 垫片shoe 模座之上下范本shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide/ram 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料? spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱梢stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑柱/顶出支柱support pin 支撑梢supporting plate 托板sweep templete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝范本二．模具钢材alloy tool steel 合金工具钢aluminium alloy 铝合金bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet邦德防蚀钢板carbon tool steel碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 硅钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑料覆面钢板三．组装、冲压、喷漆等专业词汇Assembly line组装线Layout布置图Conveyer传送带Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)pallet栈板barcode scanner条形码扫描仪fuse together熔合fuse machine热熔机operator作业员MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch英镑、英寸EMI gasket导电条front / rear plate前/后板chassis 基座/底盘bezel panel面板power button/wire电源按键/线reset button复位/重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS电源电压接拉键sheet metal parts 冲件plastic parts塑料件SOP制造作业程序material check list物料检查表work cell工作间trolley台车sub-line支线fork truck叉车planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot/transfer 机械手hydraulic machine油压机lathe车床planer 刨床miller，driller 铣床grinder磨床铣床wire cutting 线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机president董事长special assistant manager特助factory director厂长department director部长section supervisor课长group leader/supervisor组长line supervisor线长to move, to carry, to handle搬运be put in storage入库pack，packing，package包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load/ unload /return material上/卸/退料scraped 报废deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation氧化dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件trailer=long vehicle拖板车compound die复合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge/ jig/fixture夹/治具buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal 踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车glove(s) with exposed fingers割手套band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头sweeper 扫把mop拖把vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条（槽）jack升降机magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect 次要缺陷not up to standard不合规格dimension/size is a little bigger 尺寸偏大(小)cosmetic defect外观不良slipped screwhead/slippery screw head 螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位delivery deadline交货期die repair修模enterprise plan = enterprise expansion projects企划die worker模工to start /stop/switch off a press开/关机classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-grade products良品defective products, not up-to-grade products不良品waste废料board广告牌feeder送料机sliding rack滑料架defective product box不良品箱die change 换模to fix a die装模to take apart a die拆模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板to pull and stretch拉伸to put material in place, to cut material, to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stockchange材料变更feature change 特性变更evaluation评估prepare for, make preparations for准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---to throw--over switching over切换engineering, project difficulty 工程瓶颈stage die工程模automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机rack, shelf, stack料架cylinder油缸taker取料机conveyer belt输送带transmission rack输送架top /bottom 上/下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块dent压痕filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工to retrn of goods退货registration 登记registration card登记卡to put forward and hand in提报safe stock安全库存acceptance = receive验收notice通知application form for purchase请购单consume, consumption消耗abrasion磨损reverse angle = chamfer倒角to collect, to gather收集trouble故障statistics统计demand and supply需求career card履历卡to tight/ looser a bolt拧紧/松螺栓to move away a die plate移走范本easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑四.模具工程常用词汇die 模具figure file, chart file图檔cutting die, blanking die冲裁模progressive die, follow (-on)die连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印flange翻边to stake铆合design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board范本padding block垫块stepping bar垫条upper die set上模座lower die set下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品file/ document folder资料/文件夹to put file in order整理资料spare tools location手工备品仓first/ second count初/复盘人first /second check初盘/复盘复核人check人waste materials废料work in progress product在制品casing = containerazation装箱quantity of physical invetory second count 复盘点数量quantity of customs count 会计师盘,点数量the first page第一联filed by accounting department for reference会计部存查end-user/using unit(department)使用单位summary of year-end physical inventory bills 年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)本表请与盘点清册一起送会计部－(NHK厂区送财会部) Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO. 空白与作废单号plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点incoming material to be inspected进货待验steel/rolled steel钢材material statistics sheet 物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheetPCE组装厂生产排配表model机锺work order工令revision版次remark备注notes说明production control confirmation生产确认checked by初审approved by核准stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工cause description原因说明part number/ P/N 料号type形态item/group/class类别prepared by制表year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity账面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts 良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location 在途仓oversea location海外仓spare parts physical inventory list 备品盘点清单spare molds location模具备品仓skid栈板tox machine自铆机wire EDM线割EDM火花机coil stock卷料sheet stock片料score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die 公母模expansion drawing展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack 上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal密封revision版次good products良品scraped products报废品defective products不良品disposed products处理品flow chart流程窗体assembly组装stamping冲压forming成型spare part s=buffer备品coordinate坐标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill铣plane刨grind磨drill钻boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴angle offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization 碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机plain die简易模pierce die冲孔模forming die成型模progressive die连续模compound dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号)shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类: extension dwg展开图procedure dwg工程图die structure dwg模具结构图material 材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙punch wt.上模重量五金零件类: inner /outer guiding post内/外导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销guide pin导正销eq-height sleeves=spool等高套筒lifter guide pin浮升导料销wire spring圆线弹簧set screw止付螺丝located pin定位销范本类: top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模) feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板)outer /inner / lower stripper内/外/下脱料板五.模具零件类punch冲头insert嵌件deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location 定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文: compression molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝stripper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold掌上型模具移转成型用模具encapsulation molding低压封装成型射出成型用模具: two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate 浇道脱料板eject rod (bar)（成型机）顶业捧subzero深冷处理three plate 三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣六.质量人员名称类QC quality control 品质管理人员FQC final quality control 终点质量管理人员IPQC in process quality control 制程中的质量管理人员OQC output quality control 最终出货质量管理人员IQC incoming quality control 进料质量管理人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 质量工程人员质量保证类:FAI first article inspection 新品首件检查FAA first article assurance 首件确认TVR tool verification report 模具确认报告3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process 模具制程能力参数SSQA standardized supplier quality 合格供货商质量评估OOBA out of box audit 开箱检查QFD quality function deployment 质量机能展开FMEA failure model effectiveness analysis 失效模式分析8 disciplines 8项回复内容FA final audit 最后一次稽核CAR corrective action request 改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level 运作类允收质量水平S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂质量AOQL Average Output Quality Level 平均出厂质量Q/R/S Quality/Reliability/Service 质量/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV 特殊抽样水平等级AOD Accept On Deviation 特采UAI Use As ItFPIR First Piece Inspection Report首件检查报告PPM Percent Per Million百万分之一（制程统计品管专类）SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计质量管理R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限GRR Gauge Reproducibility&Repeatabilit量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它质量术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team 质量改善小组PDCA Plan Do Check Action 计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement 质量改善QP Quality Policy 目标方针TQM T otal Quality Management 全面质量管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低质量水平RMA Return Material Audit 退料认可QAN Quality Amelionrate Notice 质量改善活动ADM Absolute Dimension Measuremet 全尺寸测量QT Quality Target 质量目标7QCT ools 7 Quality Controll T ools 品管七大手法通用之件类ECN Engineering Change Notes 工程变更通知(供货商) ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面七.系统文件类QC Quality System 质量系统ES Engineering Standarization 工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦 C Compaq (美国)康伯公司C China 中国大陆 A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一般规格CMCS C-China M-Manufact C-Compaq S-Stamping Compaq 产品在龙华冲压厂制造作业规范CQCA Q-Quality A-Assembly Compaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类PMC Production & Material Control 生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manafacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部P/A Personal & Administration 人事行政部DC Document Center 资料中心QE Quality Engineering 质量工程(部)QA Quality Assurance 质量保证(处)QC Quality Control 质量管理(课)PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂) A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等) PRS Pairs 双(对等)PAL Pallet/skid 栈板PO Purchasing Order采购订单MO Manufacture Order生产订单D/C Date Code 生产日期码ID/C Identification Code (供货商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号其它OEM Original Equipment Manufacture 原设备制造PCE Personal Computer Enclosure 个人计算机外设CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China 中国大陆U.S.A the United States of America 美国E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用VS 以及JIT Just In Time 零库存I/O Input/Output 输入/输出NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-static Discharge 静电排放5S 希腊语：整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光盘CD-ROM Compact Disk Read-Only Memory 只读光盘FDD Floppy Disk Drive 软盘机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CAV Cavity 模穴CAD Computer Aid Design 计算机辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度WDR Weekly Delivery Requitement 周出货需求C/T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间)S/T Standard Time 标准时间P/M Product Market 产品市场3C Computer,Commumcation,Consumer electronic's 消费性电子5WIH When,Where,Who,What,Why,How to5M Man,Machine,Material,Method,Measurement4MIH Man,Materia,Money,Method,Time 人力,物力,财务,技术,时间(资源)SQA Strategy Quality Assurance 策略质量保证DQA Desigh Quality Assurance 设计质量保证MQA Manufacture Quality Assurance 制造质量保证SSQA Sales and service Quality Assurance销售及服务质量保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect 高磁测试FMI Frequency Modulatim Inspect 高频测试B/M Boar/Molding(flat cable)C/P Connector of PC A/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal Display CAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Achanced Basic in put/output system 先进的基本输入/输出系统CMOS Complemeruary Metoll Oxide Semiconductor 互补金属氧化物半导体PDA Personal Digital Assistant 个人数字助理IC Integrated Circuit 集成电路ISA Industry Standard Architecture 工业标准体制结构MCA Micro Channel Architecture 微信道结构EISA Extended Industry Standard Architecture 扩充的工业标准结构SIMM Single in-line memory module 单项导通汇流组件DIMM Dual in-line Memory Module 双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectivenes 失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 排线PCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WPR Weekly Delivery Requirement 周出货要求PPM Parts Per Million 百万分之一TPM Total Production Maintenance 全面生产保养MRP Material Requiremcnt Planning 物料需计划OC Operation System 操作系统TBA To Be Design 待定,定缺D/C Drawing Change P/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material Size八.模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming ?泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模九．各式模具分类用语bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模ouvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 迭层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模十.模具常用之工作机械3D coordinate measurement三次元量床boring machine搪孔机cnc milling machine CNC铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床copy lathe 仿形车床copy milling machine 仿形铣床copy shaping machine仿形刨床cylindrical grinding machine 外圆磨床die spotting machine 合模机drilling machine ?孔机engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindrical machine 内圆磨床jig boring machine 冶具搪孔机jiggrinding machine 冶具磨床lap machine 研磨机machine center 加工制造中心multi model miller 靠磨铣床drilling machine 钻床grinding machine磨床lathe 车床NC programming system NC程序制作系统planer 龙门刨床profile grinding machine 投影磨床projection grinder 投影磨床radial drilling machine 旋臂钻床shaper 牛头刨床surface grinder 平面磨床try machine 试模机turret lathe 转塔车床universal tool grinding machine 万能工具磨床vertical machine center 立式加工制造中心wire E.D.M. 线割放电加工机autocollimator 自动准直机bench comparator 比长仪block gauge 块规bore check 精密小测定器calibration 校准caliper gauge 卡规check gauge 校对规clearance gauge 间隙规clinoretee 测斜仪comparator 比测仪cylinder square 圆筒直尺depth gauge 测深规dial indicator 针盘指示表dial snap gauge 卡规digital micrometer 数位式测微计feeler gauge 测隙规gauge plate 量规定位板height gauge 测高规inside calipers 内卡钳inside micrometer 内分??卡interferometer 干涉仪leveling block 平台limit gauge 限规micrometer 测微计mil 千分之一寸monometer 压力计morse taper gauge 莫氏锥度量规nonius 游标卡尺optical flat 光学平晶optical parallel 光学平行passimeter 内径仪position scale 位置刻度profile projector 轮廓光学投影仪protractor 分角器radius 半径ring gauge 环规。

冲压模具专业词汇中英文翻译

冲压模具词汇Counter bored hole 沉孔Chamfer 倒斜角Fillet 倒圆角padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder活页夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerization装箱quantity of physical inventory second count 复盘点数量Quantity of customs count 会计师盘,点数量the first page第一联filed by accounting department for reference会计部存查end-user/using unit(department)使用单位Summary of year-end physical inventory bills 年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department) 本表请与盘点清册一起送会计部－(NHK厂区送财会部) Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO. 空白与作废单号plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet 物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model机钟work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门Stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list 备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock 卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂（degrease）main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条形码flow chart流程窗体assembly组装stamping冲压molding成型 spare parts=buffer备品coordinate坐标dismantle the die折模auxiliary function辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾deducting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave 凹convex凸short射料不足nick缺口speck瑕疪shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill钻boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴angle offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher 破碎机plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销oil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模) feature die公母模female die母模(凹模) upper plate上模板lower plate下模板die pad下垫板die holder 下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板punch冲头insert入块(嵌入件) deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate 挡块located block定位块supporting block for location 定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die 剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome 凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch 卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁) cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模全球模具网die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘? flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶? lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块汽车英语first gear 一档second gear 二档reverse 倒车档two-stroke engine 二冲程发动机diesel 柴油机limousine 豪华轿车drophead 活动车篷汽车(美作:convertible) racing car 赛车saloon 轿车(美作:sedan)wecker, beat-up car, jalopy 老爷车notchback 客货两用车four-wheel drive 四轮驱动front-wheel drive 前轮驱动trailer 拖车truck 卡车compact car 小型汽车light-van 小型货车front wheel 前轮rear wheel 后轮tread 轮距chassis 底盘bodywork, body 车身rear window 后窗玻璃windscreen 挡风玻璃(美作:windshield)windscreen wiper 风档刮水器,风档雨雪刷(美作:windshield wiper)fender, wing, mudguard 挡泥板radiator grille 水箱wing mirror 后视镜bonnet 发动机盖(美作:hood)boot 行李箱(美作:trunk) roof rack, luggage rack 行李架license plate, number plate 车号牌wing 前翼子板hubcap 轮毂罩bumper 保险杠front blinker 前信号灯taillight, tail lamp 尾灯backup light, reversing light 倒车灯stoplight, stop lamp 刹车灯rear blinker 转弯指示灯trunk, boot 行李箱bumper 保险杠tailpipe 排气管back seat, rear seat 后座driver's seat, driving seat 驾驶席passenger seat 旅客席steering wheel, wheel 方向盘rear-view mirror, driving mirror 后视镜horn, hooter 喇叭choke 熄火装置gear stick, gear change 变速杆(美作:gearshift)gearbox 变速箱starter, self-starter 起动器,起动钮brake pedal 刹车踏板clutch pedal 离合器踏板hand brake 手制动器foot brake 脚制动器dashboard 仪表板milometer 里程表speedometer, clock 速度表transmission 传动piston 活塞radiator 散热器fan belt 风扇皮带shaft 传动轴inner tube 内胎drain tap 排气阀门silencer 消音器(美作:muffler)tank 油箱overflow 溢流孔valve 阀门exhaust pipe 排气管spare wheel 备胎,备用轮胎carburettor 汽化器(美化:carburetor)electrical system, wiring 电气系统lights 灯光headlight 大灯,头灯dipped headlight 近光灯rear lights 尾灯sidelights, parking lights 位置灯,边灯direction indicator 方向标,转向标indicator, blinker 方向指示灯sparking plug 火花塞(美作:spark plug)(spare) battery (备用)蓄电池to accelerate 加速to brake 制动,刹车to engage the clutch 接上离合器to declutch 分开离合器to stall 发动机停转to change gear 变速to decelerate 减速top speed 最高速度speed limit 速度限制to park 停车to switch off the motor 熄火模具工程常用词汇模具钢材alloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板 carbon tool steel 碳素工具钢 clad sheet 被覆板 clod work die steel 冷锻模用钢 emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢 galvanized steel sheet 镀锌铁板 hard alloy steel 超硬合金钢 high speed tool steel 高速度工具钢 hot work die steel 热锻模用钢 low alloy tool steel 特殊工具钢 low manganese casting steel 低锰铸钢 marging steel 马式体高强度热处理钢 martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢 meehanite metal 米汉纳铁 merchant iron 市售钢材 molybdenum high speed steel钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢 prehardened steel 顶硬钢 silicon steel sheet 硅钢板 stainless steel 不锈钢 tin plated steel sheet 镀锡铁板 tough pitch copper 韧铜 troostite 吐粒散铁 tungsten steel 钨钢 vinyl tapped steel sheet 塑料覆面钢板四、模具零件：mold components三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板：support plate螺丝：screw 管钉：dowel pin 开模槽：ply bar scot 内模管位：core/cavity inter-lock 顶针：ejector pin司筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate 缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）：mold base 上内模：cavity insert 下内模：core insert 行位（滑块）：slide 镶件：insert 压座/斜鸡：wedge 耐磨板/油板：wedge wear plate 压条：plate 撑头: support pillar 唧嘴：sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring 中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞: pipe plug 锁模块：lock plate 斜顶：angle from pin斜顶杆：angle ejector rod 尼龙拉勾：parting locks 活动臂：lever arm 复位键、提前回杆：early return bar气阀：valves 斜导边：angle pin 术语：terms 承压平面平衡：parting surface support balance 模排气：parting line venting 回针碰料位：return pin and cavity interference 模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin 料位出上/下模：part from cavith (core) side 模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate. 不准用镶件：Do not use (core/cavity) insert 用铍铜做镶件：use beryllium copper insert 初步（正式）模图设计：preliinary (final) mold design 反呵：reverse core 弹弓压缩量：spring compressed length 稳定性好：good stability,stable 强度不够：insufficient rigidity 均匀冷却：even cooling 扣模：sticking 热膨胀：thero expansion 公差：tolorance 铜公(电极）：copper electrode 模具工程常用词汇 die 模具die shoe 模瓦figure file, chart file图档 cutting die, blanking die冲模 progressive die, follow (-on)die 连续模 compound die复合模 punched hole冲孔panel board镶块 to cutedges=side cut=side scrap切边 to bending折弯 to pull, to stretch拉伸Line streching, line pulling线拉伸 engraving, to engrave刻印 upsiding down edges翻边 to stake铆合 design modification设计变化die block模块 folded block折弯块 sliding block滑块 location pin定位销 lifting pin顶料销 die plate, front board模板 padding block垫块 stepping bar垫条 upper die base上模 lower die base下模座upper supporting blank上承板 upper padding plate blank上垫板 spare dies模具备品 spring 弹簧bolt螺栓plate电镀 mold成型 material for engineering mold testing工程试模材料 not included in physical inventory不列入盘点 incoming material to be inspected进货待验 PCE assembly production schedule sheet PCE组装厂生产排配表model机锺 work order工令 revision版次 production control confirmation生产确认 checked by初审 approved by核准 stock age analysis sheet 库存货龄分析表 on-hand inventory现有库存 available material良品可使用obsolete material良品已呆滞 to be inspected or reworked 待验或重工 cause description原因说明 part number/ P/N 料号 item/group/class类别 prepared by制 year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量 physical count quantity帐面数量 difference quantity差异 good product/accepted goods/ accepted parts/good parts良品 defective product/non-good parts不良品 disposed goods处理品 on way location在途仓 oversea location海外仓spare parts physical inventory list备品盘点清单 spare molds location模具备品仓 skid/pallet栈板 tox machine自铆机 wire EDM线割EDM放电机 coil stock卷料 sheet stock片料 tolerance工差 score=groove压线 cam block滑块 pilot导正筒 trim剪外边 pierce剪内边 drag form压锻差 pocket forthe punch head挂钩槽 slug hole废料孔feature die公母模 expansion dwg展开图 radius半径 shim(wedge)楔子 torch-flame cut火焰切割 set screw止付螺丝 form block折刀 stop pin定位销 round pierce punch=die button圆冲子 shape punch=die insert异形子 stock locater block定位块 under cut=scrap chopper清角 active plate活动板baffle plate挡块 cover plate盖板 male die公模 female die母模 groove punch压线冲子air-cushion eject-rod气垫顶杆 spring-box eject-plate弹簧箱顶板 bushing block衬套 insert 入块 capability能力 parameter参数f actor系数 phosphate皮膜化成 viscosity涂料粘度 alkalidipping脱脂 main manifold主集流脉 bezel斜视规 blanking穿落模 dejecting顶固模 demagnetization去磁;消磁 high-speed transmission高速传递 heat dissipation热传 rack上料 degrease脱脂 rinse水洗 alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly 组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕疵shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug 冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机 cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank 摸柄crank shaft曲柄augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant 冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies 复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点 dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch 侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material 材质material thickness料片厚度 press specification冲床规格die height range适用模高die height闭模高度burr毛边gap 间隙punch wt.上模重量模具机械专用词汇中英文对照abrasive grinding 强力磨削 abrasive 磨料的,研磨的 absence 不在，缺席 accesssory 附件 accommodate 适应accordingly 因此,从而,相应地 accuracy 精度,准确性 actuate 开动(机器),驱动 adequate 足够的 adhesive 粘合剂adjacent 邻近的 adopt 采用 advance 进步 advisable 可取的 agitate 摇动 a large extent 很大程度 algorithm 算法 align 定位，调准 alignment 校直 all-too-frequent 频繁 allowance 容差,余量alternate 交替,轮流 alternatively 做为选择,也许 aluminiun 铝 ample 充足的 analysis 分析 ancillary 补助的,副的 angular 有角的 annealing 退火 aperture 孔 applied loads 作用力 appropriate 适当的 arc 弧,弓形arise 出现,发生 arrange 安排 article 制品,产品 ascertain 确定,查明 assemble 组装 attitude 态度auxiliary 辅助的 avoid 避免 axis 轴 axle 轮轴,车轴 alternative 替换物 backup 备份 batch 一批 bearing 轴承,支座 bed 床身 behavior 性能 bench-work 钳工工作 bend 弯曲 beneath 在•••下 bin 仓，料架 blank 坯料 blank 冲裁,落料blanking 落料模 blast 一阵（风） blemish 缺点,污点 bolster 模座,垫板 boring 镗削,镗孔 bracket 支架 brass 黄铜 break down 破坏 breakage 破坏 brine 盐水 brittle 易碎的 buffer 缓冲器 built-in 内装的 bulging 凸肚burr 毛刺 bush 衬套 by far •••得多,最 by means of 借助于 boost 推进 cabinet 橱柜 call upon 要求 carbide 碳化物 carburzing 渗碳 carriage 拖板,大拖板 carry along 一起带走 carry down over 从•••上取下 carry out 完成case hardening 表面硬化 case 壳,套 cast steel 铸钢 casting 铸造,铸件 category 种类 caution 警告，警示cavity and core plates 凹模和凸模板 cavity 型腔,腔,洞 centre-drilling 中心孔 ceramic 陶瓷制品chain doted line 点划线 channel 通道,信道 characteristic 特性 check 核算 chip 切屑,铁屑chuck 卡盘chute 斜道 circa 大约 circlip (开口)簧环 circuit 回路,环路 circulate (使)循环 clamp 夹紧 clamp 压板 lay 泥土 clearance 间隙 clip 切断，夹住 cold hobbing 冷挤压 cold slug well 冷料井 collapse 崩塌,瓦解collapsible 可分解的 combination 组合 commence 开始,着手 commence 开始 commercial 商业的 competitive 竞争的 complementary 互补的 complexity 复杂性 complication 复杂化 compression 压缩 comprise 包含 compromise 妥协,折衷 concern with 关于 concise 简明的,简练的 confront 使面临 connector 连接口,接头 consequent 随之发生的,必然的 console 控制台 consume 消耗,占用 consummate 使完善 container 容器 contingent 可能发生的CPU (central processing unit) 中央处理器 conventional 常规的 converge 集中于一点 conversant 熟悉的conversion 换算,转换 conveyer 运送装置 coolant 冷却液 coordinate (使)协调 copy machine 仿形(加工)机床core 型芯,核心 corresponding 相应的 counteract 反作用,抵抗 couple with 伴随 contour 轮廓 crack （使）破裂，裂纹 critical 临界的 cross-hatching 剖面线 cross-section drawn 剖面图 cross-slide 横向滑板CRT (cathoder-ray tube) 阴极射线管 crush 压碎 cryogenic 低温学的 crystal 结晶状的 cubic 立方的,立方体的cup (使)成杯状,引伸 curable 可矫正的 curvature 弧线 curve 使弯曲 cutter bit 刀头,刀片 cyanide 氰化物complicated 复杂的 dash 破折号 daylight 板距 decline 下落,下降,减少 deform (使)变形 demonstrate 证明depict 描述 deposite 放置 depression 凹穴 descend 下降 desirable 合适的 detail 细节，详情 deterioration 退化,恶化 determine 决定 diagrammmatic 图解的，图表的 dictate 支配 die 模具,冲模,凹模 dielectric 电介质die-set 模架 digital 数字式数字 dimensional 尺寸的,空间的 discharge 放电,卸下,排出 discharge 卸下discrete 离散的,分立的 dislodge 拉出,取出 dissolution 结束 distinct 不同的，显著的 distort 扭曲distort (使)变形,扭曲 distributed system 分布式系统 dowel 销子 dramaticlly 显著地 drastic 激烈的draughting 绘图 draughtsman 起草人 drawing 制图 drill press 钻床 drum 鼓轮 dual 双的，双重的 ductility 延展性 dynamic 动力的 edge 边缘 e.g.(exempli gratia) [拉]例如 ejector 排出器 ejector plate 顶出板ejector rob 顶杆 elasticity 弹性 electric dicharge machining 电火花加工 electrode 电极electro-deposition 电铸 elementary 基本的 eliminate 消除,除去 elongate (使)伸长,延长 emerge 形成,显现emphasise 强调 endeavour 尽力 engagement 约束,接合 enhance 提高,增强 ensure 确保，保证 erase 抹去,擦掉evaluation 评价,估价 eventually 终于 evolution 进展 excecution 执行,完成 execute 执行electrochemical machining 电化学加工 exerte 施加 experience 经验 explosive 爆炸(性)的 extend 伸展external 外部的 extract 拔出 extreme 极端 extremely 非常地 extremity 极端 extrusion 挤压,挤出 envisage 设想 Fahrenheit 华氏温度 fabricate 制作,制造 flat-panel technology 平面(显示)技术 facility 设备 facing 端面车削 fall within 属于,适合于 fan 风扇 far from 毫不,一点不,远非 fatigue 疲劳 feasible 可行的 feature 特色,特征 feed 进给 feedback 反馈 female 阴的,凹形的 ferrule 套管 file system 文件系统 fitter 装配工,钳工fix 使固定,安装 fixed half and moving half 定模和动模 facilitate 帮助 flexibility 适应性,柔性 flexible 柔韧的 flow mark 流动斑点 follow-on tool 连续模 foregoing 在前的,前面的 foretell 预测,预示,预言 forge 锻造forming 成型 four screen quadrants 四屏幕象限 fracture 破裂 free from 免于 gap 裂口,间隙 gearbox 齿轮箱govern 统治,支配,管理 grain 纹理 graphic 图解的 grasp 抓住 grid 格子,网格 grind 磨,磨削,研磨 grinding 磨光,磨削 grinding machine 磨床 gripper 抓爪,夹具 groove 凹槽 guide bush 导套 guide pillar 导柱guide pillars and bushes 导柱和导套 handset 电话听筒 hardness 硬度 hardware 硬件 headstock 床头箱,主轴箱hexagonal 六角形的,六角的 hindrance 障碍,障碍物 hob 滚刀,冲头 hollow-ware 空心件 horizontal 水平的hose 软管,水管 hyperbolic 双曲线的 i.e. (id est) [拉]也就是 identical 同样的 identify 确定,识别 idle 空闲的 immediately 正好,恰好 impact 冲击 impart 给予 implement 实现 impossibility 不可能 impression 型腔in contact with 接触 in terms of 依据 inasmuch (as) co因为,由于 inch-to-metric conversions 英公制转换inclinable 可倾斜的 inclusion 内含物 inconspicuous 不显眼的 incorporate 合并,混合 indentation 压痕indenter 压头 independently 独自地,独立地 inevitably 不可避免地 inexpensive 便宜的 inherently 固有的injection mould 注塑模 injection 注射 in-line-of-draw 直接脱模 insert 嵌件 inserted die 嵌入式凹模inspection 检查,监督 installation 安装 integration 集成 intelligent 智能的 intentinonally 加强地，集中地interface 界面 internal 内部的 interpolation 插值法 investment casting 熔模铸造 irregular 不规则的，无规律irrespective of 不论,不管 irrespective 不顾的,不考虑的 issue 发布，发出 joint line 结合线 kerosene 煤油keyboard 健盘 knock 敲，敲打 lance 切缝 lathe 车床 latitude 自由 lay out 布置 limitation 限度,限制,局限(性)local intelligence 局部智能 locate 定位 logic 逻辑 longitudinal 纵向的 longitudinally 纵向的 look upon 视作,看待 lubrication 润滑 machine shop 车间 machine table 工作台 machining 加工 made-to-measure 定做maintenance 维护,维修 majority 多数 make use of 利用 male 阳的,凸形的 malfunction 故障 mandrel 心轴manifestation 表现,显示 massiveness 厚实，大块 measure 大小,度量 microcomputer 微型计算机 microns 微米microprocessor 微处理器 mild steel 低碳钢 milling machine 铣床 mineral 矿物,矿产 minimise 把减到最少,最小化 minute 微小的 mirror image 镜像 mirror 镜子 moderate 适度的 modification 修改,修正 modulus 系数 mold 模,铸模 mold 制模,造型 monitor 监控 monograph 专著 more often than not 常常 motivation 动机mould split line 模具分型线 moulding 注塑件 move away from 抛弃 multi-imprssion mould 多型腔模 narrow 狭窄的 NC (numerical control) 数控 nevertheless 然而,不过 nonferrous 不含铁的,非铁的 normally 通常地 novice 新手,初学者 nozzle 喷嘴,注口 numerical 数字的 objectionable 有异议的，讨厌的 observe 观察 obviously 明显地off-line 脱机的 on-line 联机 operational 操作的,运作的 opportunity 时机,机会 opposing 对立的,对面的opposite 反面 optimization 最优化 orient 确定方向 orthodox 正统的，正规的overall 全面的,全部的 overbend 过度弯曲 overcome 克服,战胜 overlaping 重叠 overriding 主要的,占优势的 opposite 对立的,对面的 pack 包装package 包装 pallet 货盘 panel 面板 paraffin 石蜡 parallel 平行的 penetration 穿透 peripheral 外围的periphery 外围 permit 许可,允许 pessure casting 压力铸造 pillar 柱子,导柱 pin 销,栓,钉 pin-point gate 针点式浇口 piston 活塞 plan view 主视图 plasma 等离子 plastic 塑料 platen 压板 plotter 绘图机 plunge 翻孔plunge 投入 plunger 柱塞 pocket-size 袖珍 portray 描绘 pot 壶 pour 灌,注 practicable 行得通的preferable 更好的,更可取的 preliminary 初步的，预备的 press setter 装模工 press 压,压床,冲床,压力机prevent 妨碍 primarily 主要地 procedure 步骤,方法,程序 productivity 生产力 profile 轮廓 progressively 渐进地 project 项目 project 凸出 projection 突出部分 proper 本身的 property 特性 prototype 原形 proximity 接近prudent 谨慎的 punch 冲孔 punch shapper tool 刨模机 punch-cum-blanking die 凹凸模 punched tape 穿孔带purchase 买，购买 push back pin 回程杆 pyrometer 高温计 quality 质量 quandrant 象限 quantity 量，数量quench 淬火 radial 放射状的 ram 撞锤 rapid 迅速的 rapidly 迅速地 raster 光栅 raw 未加工的 raw material 原材料 ream 铰大 reaming 扩孔,铰孔 recall 记起,想起 recede 收回,后退 recess 凹槽,凹座,凹进处 redundancy 过多re-entrant 凹入的 refer 指,涉及,谈及 reference 参照,参考 refresh display 刷新显示 register ring 定位环register 记录,显示,记数 regrind 再磨研 relative 相当的,比较的 relay 继电器 release 释放 relegate 把降低到reliability 可靠性 relief valves 安全阀 relief 解除 relieve 减轻,解除 remainder 剩余物,其余部分 removal 取出 remove 切除,切削 reposition 重新安排 represent 代表,象征 reputable 有名的,受尊敬的 reservoir 容器,储存器 resident 驻存的 resist 抵抗 resistance 阻力,抵抗 resolution 分辨率 respective 分别的,各自的 respond 响应,作出反应 responsibility 责任 restrain 抑制 restrict 限制，限定 restriction 限制 retain 保持,保留retaining plate 顶出固定板 reveal 显示，展现 reversal 反向 right-angled 成直角的 rigidity 钢度 rod 杆,棒rotate (使)旋转 rough machining 粗加工 rough 粗略的 routine 程序 rubber 橡胶 runner and gate systems 流道和浇口系统 sand casting 砂型铸造 satisfactorily 满意地 saw 锯子 scale 硬壳 score 刻划 scrap 废料,边角料,切屑 screwcutting 切螺纹 seal 密封 section cutting plane 剖切面secure 固定 secure 紧固,夹紧,固定 segment 分割 sensitive 敏感的 sequence 次序 sequential 相继的 seriously 严重地 servomechanism 伺服机构servomotor 伺服马达 setter 安装者 set-up 机构 sever 切断 severity 严重 shaded 阴影的 shank 柄 shear 剪,切 shot 注射shrink 收缩 side sectional view 侧视图 signal 信号 similarity 类似 simplicity 简单single-point cutting tool 单刃刀具 situate 使位于,使处于 slide 滑动,滑落 slideway 导轨 slot 槽 slug 嵌条soak 浸,泡,均热 software 软件 solid 立体,固体 solidify (使)凝固 solidify (使)固化 solution 溶液sophisiticated 尖端的,完善的 sound 结实的,坚固的 spark erosion 火花蚀刻 spindle 主轴 spline 花键 split 侧向分型,分型 spool 线轴 springback 反弹 spring-loaded 装弹簧的 sprue bush 主流道衬套 sprue puller 浇道拉杆square 使成方形 Servomechanism Laboratoies 伺服机构实验室 stage 阶段 standardisation 标准化 startling 令人吃惊的 steadily 稳定地 step-by-step 逐步 stickiness 粘性 stiffness 刚度 stock 毛坯,坯料storage tube display 储存管显示 storage 储存器 straightforward 直接的 strain 应变 strength 强度 stress 压力,应力 stress-strain 应力--应变 stretch 伸展 strike 冲击 stringent 严厉的 stripper 推板 stroke 冲程,行程structrural build-up 结构上形成的 sub-base 垫板 subject 使受到 submerge 淹没 subsequent 后来的subsequently 后来,随后 substantial 实质的 substitute 代替,替换subtract 减,减去 suitable 合适的,适当的suitably 合适地 sunk 下沉,下陷 superior 上好的 susceptible 易受影响的 sweep away 扫过 symmetrical 对称的synchronize 同步,同时发生 tactile 触觉的,有触觉的 tailstock 尾架 tapered 锥形的 tapping 攻丝 technique 技术 tempering 回火 tendency 趋向,倾向 tensile 拉力的,可拉伸的 tension 拉紧,张紧 terminal 终端机terminology 术语,用辞 theoretically 理论地 thereby 因此,从而 thermoplastic 热塑性的 thermoplastic 热塑性塑料 thermoset 热固性 thoroughly 十分地,彻底地 thread pitch 螺距 thread 螺纹 thrown up 推上 tilt 倾斜,翘起tolerance 公差 two-plate mould 双板式注射模 tong 火钳 tonnage 吨位,总吨数 tool point 刀锋 tool room 工具车间 toolholder 刀夹,工具柄 toolmaker 模具制造者 toolpost grinder 工具磨床 toolpost 刀架 torsional 扭转的toughness 韧性 trace 追踪 transverse 横向的 tray 盘，盘子，蝶 treatment 处理 tremendous 惊人的,巨大的trend 趋势 trigger stop 始用挡料销 tungsten 钨 turning 车削 twist 扭曲，扭转tracer-controlled milling machine 仿形铣床 ultimately 终于 undercut moulding 侧向分型模 undercut 侧向分型undercut 底切 underfeed 底部进料的 undergo 经受 underside 下面,下侧 undue 不适当的,过度的 uniform 统一的,一致的 utilize 利用 Utopian 乌托邦的,理想化的 valve 阀 vaporize 汽化 vaporize (使)蒸发variation 变化various 不同的,各种的 vector feedrate computation 向量进刀速率计算 vee 字形 velocity 速度 versatile 多才多艺的,万用的 vertical 垂直的 via prep经,通过 vicinity 附近 viewpoint 观点 wander 偏离方向 warp 翘曲washer 垫圈 wear 磨损 well line 结合线 whereupon 于是 winding 绕,卷 with respect to 相对于 withstand 经受,经得起 work 工件 workstage 工序 wrinkle 皱纹使皱 yield 生产 zoom 图象电子放大。

冲压模具专业词汇中英文翻译

冲压模具词汇Counter bored hole 沉孔Chamfer 倒斜角Fillet 倒圆角padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder活页夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerization装箱quantity of physical inventory second count 复盘点数量Quantity of customs count 会计师盘,点数量the first page第一联filed by accounting department for reference会计部存查end-user/using unit(department)使用单位Summary of year-end physical inventory bills 年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO. 空白与作废单号plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet 物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheetPCE组装厂生产排配表model机钟work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门Stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂（degrease）main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条形码flow chart流程窗体assembly组装stamping冲压molding成型 spare parts=buffer备品coordinate坐标dismantle the die折模auxiliary function辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾deducting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave 凹convex凸short射料不足nick缺口speck瑕疪shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill钻boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴angle offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location 定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模全球模具网die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘?flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶?lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块汽车英语first gear 一档second gear 二档reverse 倒车档two-stroke engine 二冲程发动机diesel 柴油机limousine 豪华轿车drophead 活动车篷汽车 (美作:convertible) racing car 赛车saloon 轿车 (美作:sedan)wecker, beat-up car, jalopy 老爷车notchback 客货两用车four-wheel drive 四轮驱动front-wheel drive 前轮驱动trailer 拖车truck 卡车compact car 小型汽车light-van 小型货车front wheel 前轮rear wheel 后轮tread 轮距chassis 底盘bodywork, body 车身rear window 后窗玻璃windscreen 挡风玻璃 (美作:windshield)windscreen wiper 风档刮水器,风档雨雪刷 (美作:windshield wiper) fender, wing, mudguard 挡泥板radiator grille 水箱wing mirror 后视镜bonnet 发动机盖 (美作:hood)boot 行李箱 (美作:trunk)roof rack, luggage rack 行李架license plate, number plate 车号牌wing 前翼子板hubcap 轮毂罩bumper 保险杠front blinker 前信号灯taillight, tail lamp 尾灯backup light, reversing light 倒车灯stoplight, stop lamp 刹车灯rear blinker 转弯指示灯trunk, boot 行李箱bumper 保险杠tailpipe 排气管back seat, rear seat 后座driver's seat, driving seat 驾驶席passenger seat 旅客席steering wheel, wheel 方向盘rear-view mirror, driving mirror 后视镜horn, hooter 喇叭choke 熄火装置gear stick, gear change 变速杆 (美作:gearshift) gearbox 变速箱starter, self-starter 起动器,起动钮brake pedal 刹车踏板clutch pedal 离合器踏板hand brake 手制动器foot brake 脚制动器dashboard 仪表板milometer 里程表speedometer, clock 速度表transmission 传动piston 活塞radiator 散热器fan belt 风扇皮带shaft 传动轴inner tube 内胎drain tap 排气阀门silencer 消音器 (美作:muffler)tank 油箱overflow 溢流孔valve 阀门exhaust pipe 排气管spare wheel 备胎,备用轮胎carburettor 汽化器 (美化:carburetor) electrical system, wiring 电气系统lights 灯光headlight 大灯,头灯dipped headlight 近光灯rear lights 尾灯sidelights, parking lights 位置灯,边灯direction indicator 方向标,转向标indicator, blinker 方向指示灯sparking plug 火花塞 (美作:spark plug) (spare) battery (备用)蓄电池to accelerate 加速to brake 制动,刹车to engage the clutch 接上离合器to declutch 分开离合器to stall 发动机停转to change gear 变速to decelerate 减速top speed 最高速度speed limit 速度限制to park 停车to switch off the motor 熄火模具工程常用词汇模具钢材alloy tool steel 合金工具钢 aluminium alloy 铝合金钢 bearing alloy 轴承合金 blister steel 浸碳钢 bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂 ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel钼系高速钢 molybdenum steel钼钢 nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 硅钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑料覆面钢板四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝： screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）： mold base上内模：cavity insert下内模：core insert行位（滑块）： slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴： sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate. 不准用镶件： Do not use (core/cavity) insert用铍铜做镶件： use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrode模具工程常用词汇die 模具 die shoe 模瓦figure file, chart file图档cutting die, blanking die冲模progressive die, follow (-on)die 连续模compound die复合模punched hole冲孔 panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合design modification设计变化 die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧 bolt螺栓plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点incoming material to be inspected进货待验PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次production control confirmation生产确认checked by初审approved by核准stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工cause description原因说明part number/ P/N 料号item/group/class类别prepared by制year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割 EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块capability能力parameter参数 factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬 desmut剥黑膜 D.I. rinse纯水次 Chromate铬酸处理 Anodize阳性处理 seal封孔revision版次 part number/P/N料号 good products良品 scraped products报放心品 defective products不良品finished products成品 disposed products处理品 barcode条码 flow chart流程表单 assembly组装 stamping冲压molding成型 spare parts=buffer备品 coordinate座标 dismantle the die折模 auxiliary fuction辅助功能 poly-line 多义线 heater band 加热片 thermocouple热电偶 sand blasting喷沙 grit 砂砾 derusting machine除锈机 degate打浇口 dryer烘干机 induction感应 induction light感应光 response=reaction=interaction感应 ram连杆 edge finder 巡边器 concave凸 convex凹 short射料不足 nick缺口 speck瑕疵 shine亮班 splay 银纹 gas mark焦痕 delamination 起鳞 cold slug冷块 blush 导色 gouge沟槽;凿槽 satin texture段面咬花 witness line证示线 patent专利 grit沙砾 granule=peuet=grain细粒 grit maker抽粒机cushion缓冲 magnalium镁铝合金 magnesium镁金 metal plate钣金 lathe车 mill锉 plane刨 grind磨drill铝 boring镗 blinster气泡 fillet镶;嵌边 through-hole form通孔形式 voller pin formality滚针形式 cam driver铡楔 shank摸柄 crank shaft曲柄 augular offset角度偏差 velocity速度 production tempo生产进度现状torque扭矩 spline=the multiple keys花键quenching淬火 tempering回火annealing退火 carbonization碳化 alloy合金 tungsten high speed steel钨高速的 moly high speed steel钼高速的 organic solvent有机溶剂 bracket小磁导 liaison联络单 volatile挥发性resistance电阻 ion离子titrator滴定仪 beacon警示灯 coolant冷却液 crusher破碎机模具工程类 plain die简易模 pierce die冲孔模forming die成型模 progressive die连续模 gang dies复合模 shearing die剪边模 riveting die铆合模 pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔 bending折弯 trim切边 emboss凸点dome凸圆 semi-shearing半剪 stamp mark冲记号 deburr or coin压毛边 punch riveting冲压铆合 side stretch侧冲压平 reel stretch卷圆压平 groove压线 blanking下料 stamp letter冲字(料号) shearing剪断 tick-mark nearside正面压印 tick-mark farside反面压印冲压名称类 extension dwg展开图 procedure dwg工程图 die structure dwg模具结构图 material材质material thickness料片厚度press specification冲床规格 die height range适用模高 die height闭模高度 burr毛边 gap间隙 punch wt.上模重量。